Kenwood KDC BT51U User Manual

KDC-BT51U  
KDC-5751SD  
KDC-5051U  
CD-RECEIVER  
INSTRUCTION MANUAL  
Before reading this manual, click the button below to check the latest edition and the  
modified pages.  
Check the latest edition  
© 2010 Kenwood Corporation All Rights Reserved.  
IM327_Ref_E_en_01  
English  
|
3
Before use  
Before using this unit for the first time  
This unit is initially set on the Demonstration mode.  
When using this unit for the first time, cancel the  
Demonstration mode. Refer to <Exit Demonstration  
Mode> (page 4) of Quick start guide.  
About discs used with this unit  
• This unit can only play the CDs with  
• The following discs cannot be used:  
- Discs that are not round  
- Discs with coloring on the recording surface or  
discs that are dirty  
- Recordable/Rewritable disc that has not been  
finalized (For the finalization process, refer to  
your disc writing software, and your disc recorder  
instruction manual.)  
- 8 cm (3 inch) disc (Attempt to insert using an  
adapter can cause malfunction.)  
.
2WARNING  
To prevent injury or fire, take the following  
precautions:  
• Stop the car before operating the unit.  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools) inside  
the unit.  
Handling discs  
¤
CAUTION  
• Do not touch the recording surface of the disc.  
• Adjust the volume so that you can hear sounds  
outside the car. Driving with the volume too high  
may cause an accident.  
• Wipe off the dirt on the panel with a dry silicon or  
soft cloth.  
• Do not stick tape etc. on the disc, or use a disc with  
tape stuck on it.  
• Do not use any accessories for the disc.  
• Do not use any solvents to clean discs. Use a dry  
silicon or soft cloth.  
• Clean from the center of the disc and move  
outward.  
Failure to observe this precaution may result in  
damage to the monitor or unit.”  
• When removing discs from this unit, pull them out  
horizontally.  
• Remove the rims from the center hole and disc  
edge before inserting a disc.  
Cleaning the connector  
Wipe off dirt on the connector of the unit and panel.  
Use a cotton swab or cloth  
Condensation  
When the car is air-conditioned, moisture may collect  
on the laser lens. This may cause disc read errors. In  
this case, remove the disc and wait for the moisture  
to evaporate.  
How to reset your unit  
If the unit fails to operate properly, press the Reset  
button. The unit returns to factory settings when the  
Reset button is pressed.  
Reset button  
Notes  
• If you experience problems during installation,  
consult your Kenwood dealer.  
• When you purchase optional accessories, check with  
your Kenwood dealer to make sure that they work  
with your model and in your area.  
• Characters that conform to ISO 8859-1 can be  
displayed.  
• Characters that conform to ISO 8859-5 or ISO 8859-  
1 can be displayed. Refer to “Russian” of <Initial  
setting> (page 31).  
• The Radio data system feature won’t work where  
the service is not supported by any broadcasting  
station.  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on the  
display on the actual equipment, and some of the  
illustrations on the display may be inapplicable.  
|
4
KDC-BT51U/ KDC-5751SD/ KDC-5051U  
English  
|
5
Component names  
Function setting  
1 2 3 4  
5
6
Function setting operation  
Preferences of this unit can be set in the Function  
setting mode. For detailed setting procedure and  
items, refer to the explanation for each source  
function.  
1 Select the source  
Press the [SRC] button.  
w
q
p
9
8 7  
Switch to the source to display the items to set.  
1 [ ] button  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Release button  
3 [SRC] button  
4 Control knob  
5 [PRESET] button  
6 [0] button  
3 Select the Function item  
Turn the Control knob to display the item to  
set, and then press the Control knob.  
Press the [  
item.  
] button to return to the previous  
Example:  
Play Mode  
Settings  
7 USB terminal  
8 Auxiliary input  
AUX Name Set  
9
KDC-BT51U  
Clock&Date  
Summer Time  
[
] [  
] button  
Initial Settings  
Clock Adjust  
KDC-5751SD  
DISP&ILLUMI  
Date Mode  
[SD] button  
KDC-5051U  
In this Instruction manual, the procedure to select  
“Clock Adjust” item in the Function setting layer as  
above is described as the following example:  
“Settings” > “Clock&Date” > “Clock Adjust.  
[iPod] button  
p [LOG] button  
q [DISP] button  
4 Determine the setting value  
w [  
] button  
Turn the Control knob to display the value to  
set, and then press the Control knob.  
The previous item is displayed.  
5 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
|
6
KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Audio adjustments  
Audio control  
You can set Bass, Middle, and Treble for each source.  
About Supreme  
You can adjust following Audio Control items;  
Display  
Audio item  
Subwoofer level  
Bass Boost  
Preset Equalizer  
curve  
Range  
–15 — +15 (dB)  
Level1/Level2/OFF  
“Rock”/“Pops”/“Easy”/  
“Top40”/Jazz”/ ”Game”/  
“Natural”/“User”‡  
Technology to extrapolate and supplement with proprietary  
algorithm, the high-frequency range that is cut off when  
encoding at low bit rate (less than 128Kbps, Sampling  
frequency is 44.1kHz).  
Supplementing is optimized by compression format (AAC,  
MP3 or WMA) and processed according to bit rate.  
The effect is negligible with music that is encoded at high  
bit rate, variable bit rate or has minimal high frequency  
range.  
About Dual Zone System  
Main source and sub source (Auxiliary input) output Front  
channel and Rear channel separately.  
- When “2Zone” is set to “ON, the main source sound and  
AUX input sound are output to the front speakers and rear  
speakers separately.  
- Set up the channel of sub source by “2Zone.  
- Select Main source by [SRC] button.  
- Adjust the volume of Front channel by Control knob.  
- Adjust the volume of Rear channel by “2Zone Rear  
Volume.  
- The Audio Control has no effect on sub source.  
- When Bluetooth audio source is selected, set “2Zone F/R  
Select” to “Rear. 2Zone” cannot be turned “ON” when this  
is set to “Front. While “2Zone” is turned “ON, 2Zone F/R  
Select” function is disabled.  
“SubWoofer Level”  
“Bass Boost”  
“System Q”  
“Bass Adjust”  
“Bass Center FRQ” Bass Center  
40/50/60/70/80/100/  
120/150 (Hz)  
–8 — +8 (dB)  
1.00/1.25/1.50/2.00  
OFF/ON  
Frequency  
Bass level  
“Bass Level”  
“Bass Q Factor” Bass Q Factor  
“Bass EXT”  
Bass Extend  
“Middle Adjust”  
“Middle Center  
FRQ”  
“Middle Level”  
“Middle Q Factor” Middle Q Factor  
“Treble Adjust”  
“Treble Center FRQ” Treble Center  
Frequency  
“Treble Level”  
“Balance”  
“Fader”  
“2Zone Rear Volume” Rear volume during 0 — 35  
Dual zone  
“SubWoofer”  
Middle Center  
Frequency  
Middle level  
0.5/1.0/1.5/2.0 (kHz)  
–8 — +8 (dB)  
1.0/2.0  
10.0/12.5/15.0/17.5 kHz  
Treble level  
Balance  
Fader  
–8 — +8 (dB)  
Left 15 — Right 15  
Rear 15 — Front 15  
1 Select the source to adjust  
Press the [SRC] button.  
Subwoofer output OFF/ON  
“Detailed Settings”  
“HPF Front”  
2 Enter Audio control mode  
Press the Control knob.  
Front High Pass  
Filter  
Rear High Pass Filter Through/40/60/80/100/  
120/150/180/220 (Hz)  
Through/40/60/80/100/  
120/150/180/220 (Hz)  
“HPF Rear”  
3 Select the Audio item to adjust  
Turn the Control knob to select the audio item  
for adjustment and then press the Control  
knob.  
“LPF SubWoofer” Low Pass Filter  
50/60/80/100/120/  
Through (Hz)  
“SubWoofer Phase” Subwoofer Phase Reverse (180°)/  
Normal (0°)  
“2Zone”  
“2Zone F/R Select” Dual Zone output Rear/Front  
channel  
“Supreme”  
Press the [  
item.  
] button to return to the previous  
Dual Zone System ON/OFF  
4 Adjust the Audio item  
Turn the Control knob to display the value to  
set, and then press the Control knob.  
The previous item is displayed.  
Supreme setting ON/OFF  
“Audio Preset”  
Audio Preset  
Recall/Memory  
memoy†  
“Volume Offset  
ADJ”  
Volume offset  
–8 — 0 (dB)  
(AUX: -8 — +8)  
5 Exit Audio control mode  
Press the [  
] button for at least 1 second.  
Refer to <Audio preset Memory> (page 8), <Audio preset  
recall> (page 8).  
“User”: The customized Bass, Middle, and Treble levels are  
effective.  
English  
|
7
Audio adjustments  
Audio preset Memory  
Audio preset recall  
Registering the value setup by Audio Control.  
Recalling the sound setup registered by <Audio  
preset Memory> (page 8).  
1 Setup Audio control  
Setup the <Audio control> (page 7).  
1 Select the source  
Press the [SRC] button.  
2 Enter Audio control mode  
Press the Control knob.  
2 Enter Audio control mode  
Press the Control knob.  
3 Select Audio preset memory mode  
The item can be selected and determined as  
follows.  
“Detailed Settings” > “Audio Preset”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
3 Select Audio preset memory mode  
The item can be selected and determined as  
follows.  
“Detailed Settings” > “Audio Preset”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
4 Select the Audio preset memory  
Turn the Control knob to select “Memory, and  
then press the Control knob.  
4 Select the Audio preset recall  
Turn the Control knob to select “Recall, and  
then press the Control knob.  
5 Turn the Control knob to select “YES, and  
then press the Control knob.  
“Memory Completed” is displayed.  
5 Turn the Control knob to select “YES, and  
then press the Control knob.  
“Recall Completed” is displayed.  
6 Exit Audio Control mode  
Press the [  
] button for at least 1 second.  
6 Exit Audio Control mode  
Press the [  
] button for at least 1 second.  
Register 1 pair of Audio Preset Memory. You cannot register  
by the source.  
When you press the Reset, all the sources will be the setting  
value which is registered.  
The following items can be registered.  
“Bass Center FRQ, Bass Level, Bass Q Factor, Bass EXT,  
“Middle Center FRQ, Middle Level, Middle Q Factor,  
Treble Center FRQ, Treble Level, SubWoofer Level, HPF  
Front, HPF Rear, LPF SubWoofer, SubWoofer Phase”  
|
8
KDC-BT51U/ KDC-5751SD/ KDC-5051U  
iPod control operation  
For basic operation to playback iPod contents, refer  
to the Quick Start Guide.  
Alphabet search  
You can select an alphabetic character from the  
list in the browse item (artist, album, etc.) currently  
selected.  
Music search  
1 Enter Music search mode  
Press the [ ] button twice.  
“MUSICSEARCH” is displayed.  
Searching for the song you want to play.  
1 Enter Music search mode  
Press the [ ] button.  
“MUSICSEARCH” is displayed.  
2 Select Alphabet search mode  
Turn the Control knob to select “Alphabet  
Search, and then press the Control knob.  
2 Search for music  
3 Search for character  
Operation type  
Operation  
Operation type  
Operation  
Movement between items Turn the Control knob.  
Select the characters  
Determine the characters.  
Turn the Control knob.  
Press the Control knob.  
Move to the Alphabet  
search mode  
Press the [ ] button for at least 1  
second. Refer to <Alphabet search>  
(page 9).  
Return to the Music search mode.  
Selection of item  
Press the Control knob.  
Cancelling the Alphabet search mode  
Return to previous item  
Return to Top menu  
Press the [ ] button.  
Push the Control knob towards left for at  
least 1 second.  
Press the [  
] button for at least 1 second.  
The time of Alphabet search may become long depending  
on the number of items (songs) in iPod.  
Cancelling the Music search mode  
Press the [ ] button for at least 1 second.  
To search for a character other than A to Z and 1, enter “*.  
If the first character string begins with an article “a, an,  
or “the” in the alphabet search mode, it is searched for in  
defiance of the article.  
If no characters included in a song name can be displayed,  
the browse item name and digits are displayed.  
Items  
Playlists  
Artists  
Albums  
Songs  
Display  
“PLIST***” Podcasts  
“ART***”  
“ALB***”  
“PRGM***”  
Items  
Display  
“PDCT***”  
“GEN***”  
“COM***”  
Genres  
Composers  
English  
|
9
iPod control operation  
Related search  
Direct search  
Browsing for music of the same artist or genre as  
the one being played.  
Searching for music by selecting a browse item and  
an alphabetic character(s).  
1 Enter Search select mode  
Press the [ ] button for at least 1 second.  
1 Enter Search select mode  
Press the [ ] button for at least 1 second.  
2 Select Related search mode  
Turn the Control knob to select “Related  
Search, and then press the Control knob.  
2 Select Direct search mode  
Turn the Control knob to select “Direct Search,  
and then press the Control knob.  
3 Select desired browsing item  
Turn the Control knob to select browse item,  
and then press the Control knob.  
3 Select browse item  
Turn the Control knob to select browse item,  
and then press the Control knob.  
Display  
Browses music  
Display  
Browses item  
“Search Artist”  
“Search Album”  
Displays the album of the same artist.  
Displays music in the album in which the one  
being played is included.  
“PLAYLISTS”  
Playlists  
“ARTISTS”  
Artists  
“Search Genre”  
Displays the artist of the same genre.  
“ALBUMS”  
“SONGS”  
Albums  
Songs  
“Search Composer” Displays the album including music created by the  
same composer.  
“PODCASTS”  
“GENRES”  
Podcasts  
Genres  
4 Search for music  
Operation type  
Operation  
Movement between items Turn the Control knob.  
“COMPOSERS”  
Composers  
Selection of item  
Return to previous item  
Press the Control knob.  
Press the [ ] button.  
4 Select the character to be searched for  
Turn the Control knob to select character, and  
then press the Control knob.  
Cancelling the Related search mode  
Press the [ ] button for at least 1 second.  
You can select up to three characters.  
5 Search for music  
Related search cannot be performed while playing a  
Podcast.  
Turn the Control knob to select “DONE, and  
then press the Control knob.  
A search result list is displayed.  
When the music being played has no information on  
browsing items or no music was found, “Not Found” is  
displayed.  
6 Select the music  
Turn the Control knob to select music, and then  
press the Control knob.  
Cancelling the Direct search mode  
Press the [  
] button for at least 1 second.  
|
10 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Skip search  
Skip search ratio setting  
The number of songs to be skipped is determined  
by the ratio of the total number of songs in the list  
which is selected.  
Sets the ratio of skip performed with <Skip search>  
(page 11).  
1 Select iPod source  
Press the [SRC] button.  
Select the “iPod” display.  
1 Enter Music search mode  
Press the [ ] button.  
“MUSICSEARCH” is displayed.  
2 Enter Function setting mode  
2 Enter Search select mode  
Press the [ ] button.  
Press the Control knob for at least 1 second.  
3 Select the Skip search  
The item can be selected and determined as  
follows.  
3 Select Skip search mode  
Turn the Control knob to select “Skip Search,  
and then press the Control knob.  
“Settings” > “Skip Search”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
4 Search for music  
Operation type  
Operation  
4 Set the Skip search ratio  
Movement between items Turn the Control knob.  
Skip Search  
Push the Control knob towards up or down.  
Turn the Control knob to select ratio (“0.5%,  
“1%, 5%, or “10%”), and then press the  
Control knob.  
Selection of item  
Sets the ratio of skip  
performed  
Press the Control knob.  
Push the Control knob towards right or left.  
5 Exit Function setting mode  
Cancelling the Music search mode  
Press the [ ] button for at least 1 second.  
Press the [  
] button for at least 1 second.  
The ratio of the Skip Search is set to 0.5% as default. Refer to  
<Skip search ratio setting> (page 11).  
Keep pushing Control knob for 3 seconds or longer skips  
songs at 10% regardless of the setting.  
English  
|
11  
iPod control operation  
Play mode  
Registering a song in the playlist  
You can select a Play Mode, such as Random play  
and Repeat play.  
You can register your favorite songs to make a  
playlist. You can register up to ten songs in the  
playlist.  
1 Select iPod source  
Press the [SRC] button.  
Select the “iPod” display.  
1 Play the song you want to register  
Push the Control knob towards up, down, right,  
and left.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Enter Search select mode  
Press the [ ] button for at least 1 second.  
3 Select the Play mode  
Turn the Control knob to select “Play Mode,  
and then press the Control knob.  
3 Register the song  
Turn the Control knob to select “Register My  
Playlist, and then press the Control knob.  
“## (registration number) Stored” is displayed. You  
can register up to ten songs.  
4 Select the desired Play function  
Turn the Control knob to select Play function,  
and then press the Control knob.  
Display  
“Play Mode”  
Overview  
In Music search mode  
“iPod by Hand” When set toON, allows you to operate iPod  
with the control on the iPod.  
1 Enter Music search mode  
Press the [ ] button.  
“MUSICSEARCH” is displayed.  
“ON” / “OFF”  
“Folder Random” When set toON, plays the music in the folder  
randomly. (Music only)  
2 Play the song you want to register  
Refer to <Music search> (page 9).  
“ON” / “OFF”  
“All Random”  
“File Repeat”  
When set toON, plays all songs in iPod  
randomly. (Music only)  
“ON” / “OFF”  
When set toON, plays the music repeatedly.  
“ON” / “OFF”  
3 Enter Register playlist mode  
Press the [ ] button.  
4 Register the song  
Turn the Control knob to select “Register My  
Playlist, and then press the Control knob.  
“## (registration number) Stored” is displayed. You  
can register up to ten songs.  
(
: Factory setting)  
5 Set the Play function  
Press the Control knob.  
The previous item is displayed.  
6 Exit Function setting mode  
When creating a playlist, you can register the songs stored  
in one iPod. If you attempt to register a song by connecting  
an unregistered iPod, “My Playlist Delete” is displayed.  
Selecting “YES” deletes the playlist.  
Press the [  
] button for at least 1 second.  
If you attempt to register the eleventh song, “Memory Full”  
is displayed and you cannot register the song. To register it,  
delete an unnecessary song.  
Do not register Podcasts. Songs may be registered or played  
improperly. For example, unintended songs are registered.  
|
12 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Playing the playlist  
Deleting a song from the playlist  
1 Enter Search select mode  
Press the [ ] button for at least 1 second.  
1 Enter Search select mode  
Press the [ ] button for at least 1 second.  
2 Select Recall playlist mode  
Turn the Control knob to select “Recall My  
Playlist, and then press the Control knob.  
2 Select Delete playlist mode  
Turn the Control knob to select “Delete My  
Playlist, and then press the Control knob.  
3 Play a song in the playlist  
3 Select how to delete song(s)  
Turn the Control knob to select the song you  
want to play, and then press the Control knob.  
Turn the Control knob to select “Delete One” or  
“Delete All, and then press the Control knob.  
Selecting “Delete All” deletes all songs.  
Selecting “Delete All” moves to step 5 and all songs  
are deleted.  
To stop playing the song in the playlist, turn the power off.  
If a song does not end with 1 second or longer silence, its  
last portion may not be played.  
4 Select the song to delete  
Turn the Control knob to select the song, and  
then press the Control knob.  
Songs cannot be played at random during playback of the  
songs in playlist.  
5 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Completed” is displayed.  
In Function setting mode  
1 Select iPod source  
Press the [SRC] button.  
Select the “iPod” display.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select the Playlist delete mode  
The item can be selected and determined as  
follows.  
“Settings” > “My Playlist Delete” > “Delete One”  
or “Delete All”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
Selecting “Delete All” deletes all songs.  
Selecting “Delete All” moves to step 5 and all songs  
are deleted.  
4 Select the song to delete  
Turn the Control knob to select the song, and  
then press the Control knob.  
5 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Completed” is displayed.  
6 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
English  
|
13  
Music disc/Audio file (CD, USB, or SD) Operation  
For basic operation to playback Music disc/Audio  
file contents, refer to the Quick Start Guide.  
Music Editor media  
Skip search  
The number of songs to be skipped is determined  
by the ratio of the total number of songs in the list  
which is selected.  
Music search  
1 Enter Music search mode  
Press the [ ] button.  
Selecting the music you want to listen to from the  
device or media being played now.  
“MUSICSEARCH” is displayed.  
1 Enter Music search mode  
Press the [ ] button.  
“MUSICSEARCH” is displayed.  
2 Enter Search select mode  
Press the [ ] button.  
3 Select Skip search mode  
Turn the Control knob to select “Skip Search,  
and then press the Control knob.  
2 Search for music  
Audio file  
Operation type  
Movement between  
folders/files  
Selection of folder/flie Press the Control knob.  
Return to previous folder Press the [ ] button.  
Operation  
Turn the Control knob.  
4 Search for music  
Operation type  
Operation  
Movement between items Turn the Control knob.  
Skip Search  
Selection of item  
Sets the ratio of skip  
performed  
Push the Control knob towards up or down.  
Press the Control knob.  
Push the Control knob towards right or left.  
Return to root folder  
Push the Control knob towards left for at  
least 1 second.  
Cancel the Music Search Press the [ ] button for at least 1 second.  
mode  
Cancelling the Music search mode  
Press the [ ] button for at least 1 second.  
¡ indicator: Audio file  
] indicator: Folder  
The ratio of the Skip Search is set to 0.5% as default. Refer to  
<Skip search ratio setting> (page 11).  
Keep pushing Control knob for 3 seconds or longer skips  
songs at 10% regardless of the setting.  
CD source  
Operation type  
Movement between track Turn the Control knob.  
Operation  
Selection of track  
Press the Control knob.  
Return to first track  
Push the Control knob towards left for at  
least 1 second.  
Cancel the Music Search Press the [ ] button.  
mode  
|
14 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Function of disc changers with KDC-5751SD/  
KDC-5051U  
Play mode  
You can select a Play Mode, such as Random play  
and Repeat play.  
Basic operation of Disc changer  
(Optional)  
1 Select CD/ USB/ SD source  
Press the [SRC] button.  
Select the “CD, USB, or “SD” display.  
Selecting CD changer source  
Press the [SRC] button.  
Select the “CD CH” display.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
Music search  
Push the Control knob towards right or left.  
3 Select the Play function mode  
Turn the Control knob to select “Play Mode,  
and then press the Control knob.  
Disc search  
Push the Control knob towards up or down.  
4 Select the desired Play function  
Turn the Control knob to select Play function,  
and then press the Control knob.  
Display  
Overview  
“Play Mode”  
“Track Scan”(CD)/ When set toON, plays the intro of the music  
“File Scan”(Audio in the disc/folder successively.  
file)  
“ON” / “OFF”  
“Disc Random”(CD)/ When set to“ON, plays the music in the folder  
“Folder Random” randomly.  
(Audio file)  
“ON” / “OFF”  
“All Random”  
When set toON, plays all songs in CD/USB  
randomly. (Audio file only)  
“ON” / “OFF”  
“Track Repeat”(CD)/ When set toON, plays the music repeatedly.  
“File Repeat”(Audio “ON” / “OFF”  
file)  
“Disc Repeat”(CD When set to“ON, plays the music in the disc/  
changer)/“Folder folder repeatedly.  
Repeat”(Audio file) “ON” / “OFF”  
“MGZN Random” When set toON, plays the music in the disc  
changer randomly. (Disc changer only)  
“ON” / “OFF”  
(
: Factory setting)  
5 Set the Play function  
Press the Control knob.  
The previous item is displayed.  
6 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
KDC-5751SD  
Press the SD button during SD source, move to the Play  
function mode.  
English  
|
15  
Tuner Operation  
For basic operation to listen to the radio, refer to the  
Quick Start Guide.  
Seek mode setting  
Selects the tuning mode of the radio.  
1 Select Tuner source  
Press the [SRC] button.  
Select the “TUNER” display.  
Auto memory  
Memorizes 18 (FM)/ 6 (AM) stations with good  
reception automatically.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
1 Select Tuner source  
Press the [SRC] button.  
Select the “TUNER” display.  
3 Select the Seek mode  
The item can be selected and determined as  
follows.  
“Settings” > “Seek Mode”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select the Auto memory mode  
The item can be selected and determined as  
follows.  
4 Set to the desired Seek mode  
Tuning mode  
Display Operation  
Auto seek  
“Auto1” Automatic search for a station.  
“Settings” > “Auto Memory”  
Preset station seek “Auto2” Search in order of the stations in the  
Preset memory.  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
Manual  
“Manual” Normal manual tuning control.  
4 Start Auto memory mode  
Turn the Control knob to select “YES, and then  
press the Control knob.  
Turn the Control knob to select Seek mode, and  
then press the Control knob.  
5 Exit Function setting mode  
When 18 (FM)/ 6 (AM) stations that can be received  
are put in the memory, auto memory entry closes.  
Press the [  
] button for at least 1 second.  
|
16 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
6 Exit Function setting mode  
Press the [ ] button for at least 1 second.  
Tuner setting  
Sets the tuner items.  
1 Select Tuner source  
Press the [SRC] button.  
Select the “TUNER” display.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select the Setting mode  
Turn the Control knob to select “Settings, and  
then press the Control knob.  
4 Select the desired Tuner setting item  
Turn the Control knob to select Tuner setting  
item, and then press the Control knob.  
Display  
Overview  
“Settings”  
“Local Seek”  
Only stations whose reception is good are  
searched in auto seek tuning.  
“ON” / “OFF”  
“MONO”  
You can reduce the noise when stereo  
broadcasts are received as monaural.  
“ON” / “OFF”  
“News Interrupt” Automatically receives news bulletin when  
it starts. Set the time during which interrupt  
is to be disabled after start of another news  
bulletin.  
Changing“00MIN”to“90MIN”turns this  
function ON.  
If news bulletin starts when this function is  
ON, “NEWS”is displayed and news is received.  
If“20MIN”is has been set, reception of another  
news bulletin will not start for 20 minutes.  
The news bulletin volume is the same level  
that was set for Traffic Information.  
“OFF” / “00MIN” – “90MIN”  
“AF”  
When the reception is poor, automatically  
alternate to another frequency broadcasting  
the same program in the same Radio data  
system network with better reception.  
“ON” / “OFF”  
“Regional”  
Sets whether to switch to the station only in  
the specific region using theAF SETcontrol.  
“ON” / “OFF”  
“Auto TP Seek”  
When traffic information station reception is  
poor, automatically searches for a station that  
can be received better.  
“ON” / “OFF”  
(
: Factory setting)  
5 Set the Tuner setting item  
Turn the Control knob to select desired value,  
and then press the Control knob.  
The previous item is displayed.  
English  
|
17  
Tuner Operation  
PTY (Program Type)  
Program Type preset  
Selecting the Program Type below and searching  
for a station;  
Putting the Program Type in the Preset button  
memory and quick recall.  
Program Type Display  
Program Type Display  
Serious Classical “Classics”  
Presetting the Program Type  
Speech  
Music  
News  
“Speech”  
“Music”  
“News”  
1 Select the Program Type to preset  
Refer to <PTY (Program Type)> (page 18).  
Other Music  
Weather  
Finance  
“Other M”  
“Weather”  
“Finance”  
Current Affairs  
Information  
Sport  
“Affairs”  
“Info”  
“Sport”  
2 Enter Program Type preset mode  
Press the [PRESET] button.  
Children’s programs “Children”  
Social Affairs  
Religion  
Phone In  
“Social”  
3 Select a number and store it in the memory  
Turn the Control knob to select memory  
number (“1” – “6”), and then press the Control  
knob for at least 2 seconds.  
Education  
Drama  
Culture  
Science  
Varied  
Pop Music  
Rock Music  
Easy Listening  
Music  
“Educate”  
“Drama”  
“Culture”  
“Science”  
“Varied”  
“Pop M”  
“Rock M”  
“Easy M”  
“Religion”  
“Phone In”  
“Travel”  
Travel  
Leisure  
“Leisure”  
“Jazz”  
“Country”  
“Nation M”  
“Oldies”  
Jazz Music  
Country Music  
National Music  
Oldies Music  
Folk Music  
Documentary  
Cancelling the Preset Memory mode  
Press the [  
] button.  
Recalling the preset Program Type  
“Folk M”  
“Document”  
Light Classical  
“Light M”  
1 Enter PTY mode  
Press the [ ] button twice.  
Speech and Music include the Program type shown  
below.  
Music: Black character item.  
Speech: White character item.  
2 Enter Preset memory mode  
Press the [PRESET] button.  
3 Select the number you want to recall from the  
memory  
Turn the Control knob to select recall number  
(“1” – “6”), and then press the Control knob.  
1 Enter PTY mode  
Press the [ ] button twice.  
2 Select the Program Type  
Turn the Control knob.  
3 Search for the selected Program Type station  
Push the Control knob towards right or left.  
4 Exit PTY mode  
Press the [  
] button.  
This function cannot be used during a traffic bulletin or AM  
reception.  
When the selected Program Type is not found, “No PTY” is  
displayed. Select another Program Type.  
|
18 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Changing Language for PTY Function  
Selecting the Program Type display language as  
follows;  
Language  
English  
French  
Display  
“English”  
“French”  
“German”  
German  
1 Enter PTY mode  
Press the [ ] button twice.  
2 Enter Changing Language mode  
Press the Control knob.  
3 Select the language  
Turn the Control knob to select language, and  
then press the Control knob.  
English  
|
19  
Log memory  
Log memory recall  
Log memory item lock  
This unit automatically memorizes the previously  
used functions and Function setting items, which  
can easily be recalled.  
Locks Log memory items to avoid them being  
deleted.  
1 Display the Log memory list  
Press the [LOG] button.  
1 Display the Log memory list  
Press the [LOG] button.  
2 Lock the Log memory item  
2 Recall the desired function  
Turn the Control knob to select function, and  
then press the Control knob.  
Turn the Control knob to select item, and then  
press the Control knob for at least 1 second.  
Locked items are indicated with “ .  
Category display  
“FM”  
“AM”  
“iPod”  
“USB”  
Function category  
FM broadcast  
AM broadcast  
iPod music  
3 Exit Log memory  
Press the [  
] button.  
USB music  
“SD”  
SD card  
“CD”  
CD music  
“PLAY”  
“INIT”  
“SET”  
Play mode item  
Initial setting item  
Setting item  
“DISP”  
“AUD”  
“BT”  
Display setting item  
Audio control setting  
Calling number  
Cancelling the Log memory recall  
Press the [ ] button.  
Maximum of 15 recently used functions are logged. When  
this limit is reached, they are deleted from the oldest.  
Logged functions can be deleted. Refer to <Deleting a Log  
memory item> (page 21).  
Functions to be logged can be set by categories. Refer to  
<Log memory category setting> (page 21).  
Logged functions can be locked to avoid them being  
deleted. Refer to <Log memory item lock> (page 20).  
Stations are logged after 2 minutes of reception.  
This timing can be changed. Refer to <Tuner log memory  
time setting> (page 22).  
|
20 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Deleting a Log memory item  
Log memory category setting  
Deletes Log memory items.  
Sets the function category to be logged.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select the Log delete mode  
The item can be selected and determined as  
follows.  
2 Select the Log memory setting mode  
The item can be selected and determined as  
follows.  
“Settings” > “Log” > “Log Delete”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
“Settings” > “Log” > “Log Settings”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
3 Select the Log memory item to delete  
Turn the Control knob to select Log memory  
item, and then press the Control knob.  
Selecting “All” deletes all Log memory. (exclude a  
locked items.)  
3 Set the category to be logged  
Category display  
“Tuner Log”  
“Data CD Log”  
“iPod Log”  
Setting category  
Radio-related  
CD-related  
iPod-related  
“USB Log”  
“SD Log”  
“Phone Log”  
“Function Log”  
USB-related  
SD card-related (KDC-5751SD only)  
Call-related  
4 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Completed” is displayed.  
Function setting-related  
5 Exit Function setting mode  
Turn the Control knob to select category, and  
then press the Control knob.  
Press the [  
] button for at least 1 second.  
4 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
English  
|
21  
Log memory  
Tuner log memory time setting  
You can set the timing to log the station by the  
reception time.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select the Tuner log time set mode  
The item can be selected and determined as  
follows.  
“Settings” > “Log” > “Tuner Log Time Set”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
3 Set the reception time for the timing to start  
logging the station  
Turn the Control knob to select time (“10SEC,  
“30SEC, 1MIN, 2MIN, or “5MIN”), and then  
press the Control knob.  
4 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
|
22 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
English  
|
23  
Display settings  
Selecting display type  
Selecting text display  
Shown below are examples of display types.  
Changes displayed information on each of the  
following sources:  
Display type Display information  
Type A  
Type B  
Type C  
Type D  
Type E  
Displays 3 lines of text.  
Displays 2 line of text.  
Displays the clock.  
Displays the spectrum analyzer.  
Displays off.  
In Tuner source  
Information  
Frequency & Program Service name (FM)  
Song title(FM)*  
Artist name(FM)*  
Title & Artist name(FM)**  
Station name(FM)  
Radio text +(FM)  
Radio text(FM)  
Frequency (MW, LW)  
Spectrum analyzer & Clock  
Date  
Display  
“Frequency/PS”  
“Song Title”  
“Artist Name”  
“Title/Artist”  
“Station Name”  
“Radio Text Plus”  
“Radio Text”  
“Frequency”  
“Speana/Clock”  
“Date”  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select the Display type select mode  
The item can be selected and determined as  
follows.  
“Settings” > “DISP&ILLUMI” > “Display Select” >  
“Type Select”  
Blank  
“Blank”  
Information of Radio text plus is displayed.  
*Dispaly type A only  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
**Dispaly type B only  
3 Select the Display type  
Turn the Control knob to select Display type,  
and then press the Control knob.  
In CD & External disc source  
Information  
Disc title  
Display  
“Disc Title”  
“Track Title”  
“P-Time”  
Track title  
Play time  
4 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
Spectrum analyzer & Clock  
Date  
“Speana/Clock”  
“Date”  
Blank  
“Blank”  
In Audio file/ iPod source  
Information  
Display  
Song Title*  
Album name*  
Artist name*  
Title & Artist name**  
Album & Artist name  
Folder name  
“Song Title“  
“Album Name”  
“Artist Name”  
“Title/Artist”  
“Album/Artist”  
“Folder Name”  
“File Name”  
“P-Time”  
File name  
Play time  
Spectrum analyzer & Clock  
Date  
“Speana/Clock”  
“Date”  
Blank  
“Blank”  
*Dispaly type A only  
**Dispaly type B only  
In Standby/ Auxiliary input source  
Information  
Display  
Source name  
Spectrum analyzer & Clock (AUX only)  
Clock (Standby only)  
“Source Name”  
“Speana/Clock”  
“Clock”  
Date  
“Date”  
Blank  
“Blank”  
|
24 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
In Bluetooth Audio “BT AUDIO EXT” (Optional  
accessory KCA-BT200, KCA-BT300) source  
Information display setting  
Sets side and graphic parts of the display.  
Information  
Display  
Source name  
Spectrum analyzer & Clock  
Date  
“Source Name”  
“Speana/Clock”  
“Date”  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select the Display select mode  
The item can be selected and determined as  
follows.  
Title & Artist name (KCA-BT300 only)  
Album & Artist name (KCA-BT300 only)  
Blank  
“Title/Artist”  
“Album/Artist”  
“Blank”  
“Settings” > “DISP&ILLUMI” > “Display Select”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select the desired Information display setting  
item  
Turn the Control knob to select Display setting  
item, and then press the Control knob.  
2 Select Text display selection mode  
The item can be selected and determined as  
follows.  
“Settings” > “DISP&ILLUMI” > “Display Select” >  
Text Select”  
Display  
Overview  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
“Display Select”  
“Side Select”  
Sets the side part display for Type A, B, and D.  
1 / 2 / 3  
3 Select the text display part  
Push the Control knob towards up or down.  
The selected text display part blinks.  
“Graphic Select”  
“Status”  
Sets the Type C clock display and Type D  
spectrum analyzer display.  
1 / 2  
Sets the status display (ON/OFF indicator for  
each function) for Type A and B.  
“ON” / “OFF”  
4 Select the text  
Turn the Control knob.  
5 Exit Function setting mode  
(
: Factory setting)  
Press the [  
] button for at least 1 second.  
4 Set the Display setting item  
Turn the Control knob to select desired value,  
and then press the Control knob.  
The previous item is displayed.  
If the selected display item does not have any information,  
alternative information is displayed.  
Setting is available when the Display type is A or B which  
allows text display. Refer to <Selecting display type> (page  
24).  
5 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
Some items cannot be selected depending on the display  
type and row.  
When selecting “Folder name” while playing with iPod,  
names will be displayed depending on currently selected  
browsing items.  
If the iPod Control by Hand Mode is set to on while playing  
the iPod, “iPod by Hand Mode” is displayed.  
If all characters cannot be displayed while playing with iPod,  
the file number in the list is displayed.  
Information  
Music title  
Folder name  
File name  
Display  
“TITLE***”  
“FLD***”  
“FILE***”  
English  
|
25  
Display settings  
Illumination color selection  
Display & Illumination setting  
Selecting the Illumination Color of the panel.  
Sets the display and illumination.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select Color select mode  
The item can be selected and determined as  
follows.  
2 Select Display & Illumination setting mode  
The item can be selected and determined as  
follows.  
“Settings” > “DISP&ILLUMI” > “Color Select”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
“Settings” > “DISP&ILLUMI”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
3 Select the part where you want to set the  
Illumination Color  
3 Select the desired Display & Illumination  
setting item  
Turn the Control knob to select Display &  
Illumination setting item, and then press the  
Control knob.  
Display  
“Color Select”  
“ALL”  
Part  
All  
“Display”  
“Key”  
Display  
Button  
Display  
“DISP&ILLUMI”  
Overview  
“USB&AUX”  
USB terminal and Auxiliary input  
“Display Dimmer” Dims the display part in conjunction with the  
light switch of the vehicle.  
Turn the Control knob to select part, and then  
press the Control knob.  
“Auto”: Dims the display in conjunction with  
the Light switch of the vehicle.  
“Manual1”: Dims the display constantly.  
“Manual2”: Dims the display darker than  
Manual1.  
“OFF”: Does not dim the display.  
Sets the display contrast.  
4 Select the Illumination Color  
Turn the Control knob to select color, and then  
press the Control knob.  
Select the color from “Variable Scan”/ “Color1” —  
“Color24.  
“Contrast”  
“1” – ”10” – “30”  
“DISP NEGA/POSI” Switches the panel display between positive  
or negative.  
Adjusting RGB values  
You can create your original color during the  
selection from “Color1” — “Color24.”  
The color you created can be called when you  
select “User.  
1. Press the Control knob for at least 1 second.  
Enter the detail color adjustment mode.  
2. Set the color.  
“NEGA1”: Displays the text in the negative.  
“NEGA2”: When the interior light is off, the  
text is displayed in the negative;  
when the interior light is on, the text  
is displayed in the positive.  
“POSI1”: Displays the text in the positive.  
“POSI2”: When the interior light is off, the text  
is displayed in the positive; when  
the interior light is on, the text is  
displayed in the negative.  
Sets the method of scroll to view hidden text.  
“Auto” : Scrolls.  
“Once” : Scrolls once.  
“OFF” : Does not scroll.  
Operation type  
To select the color to adjust. Push the Control knob towards right  
(red, green, or blue)  
To adjust color.  
(Range: 0 – 9)  
Operation  
“Text Scroll”  
or left.  
Turn the Control knob.  
3. Press the Control knob.  
Exit the detail color adjustment mode.  
“BT DVC Status”  
You can display the connection status, signal  
strength, and battery level.  
: Battery level of cell-phone.  
: Signal strength of cell-phone.  
5 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
|
26 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
“ILLUMI Dimmer” Reduces the key Illumination brightness.  
“Auto”: Dims the illumination in conjunction  
with the Light switch of the vehicle.  
“Manual1”: Dims the illumination constantly.  
“Manual2”: Dims the illumination darker than  
Manual1.  
“OFF”: Does not dim the illumination.  
“ILLUMI Effect”  
Sets whether the key illumination color is  
changed in conjunction with the key operation.  
“ON” / “OFF”  
“ILLUMI Music  
SYNC”  
Sets whether the key illumination color is  
changed in conjunction with the sound  
volume.  
“ON” / “OFF”  
(
: Factory setting)  
4 Set the Display & Illumination setting items  
Turn the Control knob to select desired value,  
and then press the Control knob.  
The previous item is displayed.  
5 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
English  
|
27  
General operation  
Adjusting the Clock  
Adjusting the Date  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select the Clock Adjust mode  
The item can be selected and determined as  
follows.  
2 Select the Date Adjust mode  
The item can be selected and determined as  
follows.  
“Settings” > “Clock&Date” > “Clock Adjust”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
“Settings” > “Clock&Date” > “Date Adjust”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
3 Set hour  
3 Set year  
Turn the Control knob to adjust the hour, and  
then press the Control knob.  
Turn the Control knob to adjust the year, and  
then press the Control knob.  
4 Set minute  
Turn the Control knob to adjust the minute, and  
then press the Control knob.  
4 Set month  
Turn the Control knob to adjust the month, and  
then press the Control knob.  
5 Exit Function setting mode  
5 Set day  
Press the [  
] button for at least 1 second.  
Turn the Control knob to adjust the day, and  
then press the Control knob.  
For adjustment during summer time, refer to “Summer Time”  
6 Exit Function setting mode  
Press the [  
of <Clock & Date display type setting> (page 29).  
] button for at least 1 second.  
|
28 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Dual clock display  
Clock & Date display type setting  
Sets time for two different cities.  
Sets the display type of the clock and calendar.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select the City Select mode  
The item can be selected and determined as  
follows.  
2 Select the Clock & Date setting mode  
The item can be selected and determined as  
follows.  
“Settings” > “Clock&Date” > “City Select”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
“Settings” > “Clock&Date”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
3 Select the clock display part  
3 Select the desired Clock & Date setting item  
Turn the Control knob to select Clock & Date  
display setting item, and then press the Control  
knob.  
Push the Control knob towards up or down.  
4 Set cities for Home/ Sub  
Turn the Control knob.  
Display  
“Clock&Date”  
Overview  
5 Determine cities for Home/ Sub  
Press the Control knob.  
“Time Synchronized” Synchronizing the Radio data system station  
time data and this unit’s clock.  
6 Exit Function setting mode  
“ON” / “OFF”  
Advances the clock one hour when set to ON.  
“ON” / “OFF”  
Press the [  
] button for at least 1 second.  
“Summer Time”  
For adjustment of Home time, refer to <Adjusting the  
Clock> (page 28).  
“Sub Clock Adjust” Adjusts the time difference caused by summer  
time.  
Time of Sub City is automatically derived from Home time.  
When summer time systems are different between Home  
and Sub cities, adjustment can be done by referring to  
“Sub Clock Adjust” of <Clock & Date display type setting>  
(page 29).  
“-1h” / “0h” / “+1h”  
Sets the date display mode.  
7 types  
“Date Mode”  
(
: Factory setting)  
4 Set the Clock & Date setting items  
Turn the Control knob to select desired value,  
and then press the Control knob.  
The previous item is displayed.  
5 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
English  
|
29  
General operation  
Function of KDC-5751SD, KDC-5051U  
Muting the audio upon reception of  
phone call  
Auxiliary input display setting  
Sets the display when switched to AUX source.  
1 Select the AUX source  
Press the [SRC] button.  
Select the “AUX” display.  
The audio system automatically mutes when a call  
comes in.  
When a call comes in  
“CALLis displayed.  
The audio system pauses.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select the Name set mode  
The item can be selected and determined as  
follows.  
Listening to the audio during a call  
Press the [SRC] button.  
The “CALLdisplay disappears and the audio system  
comes back ON.  
“Settings” > “AUX Name Set”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
When the call ends  
Hang up the phone.  
The “CALLdisplay disappears and the audio system  
comes back ON.  
4 Sets the display of the AUX source  
Turn the Control knob to select Auxiliary input  
display, and then press the Control knob.  
Select “AUX, DVD, PORTABLE, GAME, VIDEO, or  
“TV.  
To use the TEL Mute feature, you need to hook up the MUTE  
wire to your telephone using a commercial telephone  
accessory. Refer to <Connecting wires to terminals> (page  
12) of Quick start guide.  
5 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
|
30 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
“CD Read”  
Sets the method for reading CD.  
Initial setting  
When unable to play special format CD, set  
this function to“2”to force playing. Note that  
some music CDs may be unplayable even  
when set to“2.  
In addition, audio files cannot be played when  
set to“2. Normally, keep this set to“1.  
1: Automatically distinguishes between audio  
file disc and music CD when playing disc.  
2: Forces playing as music CD.  
Configures initial settings of this unit.  
1 Select Standby  
Press the [SRC] button.  
Select the “STANDBY” display.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
“Built-in AMP”  
“Speaker Select”  
Selecting“OFF”turns off the built-in amplifier.  
Turning off the built-in amplifier improves the  
quality of the sound from Preout.  
“ON” / “OFF”  
Fine-tuning so that the System Q value is  
optimal when setting the speaker type as  
follows;  
3 Select the Initial setting mode  
Turn the Control knob to select “Initial Settings,  
and then press the Control knob.  
4 Select the desired Initial setting item  
Turn the Control knob to select Initial setting  
item, and then press the Control knob.  
“OFF”: OFF  
“5/4inch”: For 5 & 4 in. speaker  
“6x9/6inch”: For 6 & 6x9 in. speaker  
“O.E.M.”: For the OEM speaker  
Display  
“Initial Settings”  
“Source Select”  
Overview  
Select“2”to change the source selection  
method. Press the [SRC] button, turn the  
Control knob to select the source, and then  
press the Control knob to determine it.  
1 / 2  
Setting the operation check sound (beep  
sound) ON/OFF.  
“F/W Update #.##” Upgrades the firmware.  
Selecting“YES”and then pressing Control knob  
starts upgrading the firmware.  
For how to update the firmware, access our  
web site.  
“Key Beep”  
“Russian”  
(
: Factory setting)  
“ON” / “OFF”  
When this is set to ON, the following character  
strings are displayed in Russian:  
Folder name/ File name/ Song title/ Artist  
name/ Album name/ KCA-BT200/BT300  
(optional accessory)  
5 Set the Initial setting item  
Turn the Control knob to select desired value,  
and then press the Control knob.  
The previous item is displayed.  
“ON” / “OFF”  
6 Exit Function setting mode  
“Function Language” Changes the display language of items in  
Function setting.  
Press the [  
] button for at least 1 second.  
“English” / “Français” / “Español” /  
“Deutsch” / “Italiano” / “Pyccкий”  
“Power OFF Wait” Setting the timer to turn this unit’s power OFF  
automatically when Standby mode continues.  
Using this setting can save the vehicle’s battery  
power.  
“OFF”: Power OFF Timer function is OFF.  
“20MIN”:Turns the power OFF after 20  
minutes. (Factory setting)  
“40MIN”:Turns the power OFF after 40  
minutes.  
“60MIN”:Turns the power OFF after 60  
minutes.  
“Built-in AUX”  
Sets whether to display AUX during source  
selection.  
“ON” / “OFF”  
English  
|
31  
General operation  
Demonstration mode Setting  
Turning the demonstration mode ON/OFF.  
1 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Select the Demonstration mode  
Turn the Control knob to select “DEMO Mode,  
and then press the Control knob.  
3 Set the Demonstration mode  
Turn the Control knob to select desired value  
(“ON” or “OFF”), and then press the Control  
knob.  
Exit Function setting mode.  
|
32 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
English  
|
33  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Operation of hands-free phoning  
Function of KDC-BT51U  
Before use  
Registering cell-phone  
KDC-BT51U  
• If your cell-phone is not yet registered, register (pair)  
it by referring to <Registering cell-phone> (page 9)  
in the Quick Start Guide or <Registering cell-phone>  
(page 34) in this document.  
• To register a new cell-phone, you can also refer to  
<Registering cell-phone> (page 34).  
1 Enter Bluetooth mode  
Press the [ ] button for at least 1 second.  
If your cell-phone is not yet registered, the search  
for a cell-phone starts with “Searching” displayed.  
Paring with new cell-phone  
Turn the Control knob to select “Device Search,  
and then press the Control knob.  
The search for a cell-phone starts with “Searching”  
displayed.  
KDC-5751SD/ KDC-5051U  
• If your cell-phone is not yet registered, register (pair)  
it by referring to <Registering cell-phone> (page 9)  
in the Quick Start Guide or <Registering Bluetooth  
device> (page 44) in this document.  
2 Select the used cell-phone  
Turn the Control knob to select cell-phone  
name, and then press the Control knob.  
• For details on the Bluetooth cell-phone with the  
hands-free function, see <About the Cell-phone>  
(page 53).  
3 Input the PIN code  
Operation type  
Operation  
Select the numbers.  
Move to the next digit.  
Delete the last digit.  
Transmit the PIN code.  
Turn the Control knob.  
Push the Control knob towards right.  
Push the Control knob towards left.  
Press the Control knob.  
Pairing completes with “HF Connect” displayed.  
When any error code is displayed while the paring is in  
progress, refer to <Troubleshooting guide> (page 54).  
|
34 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Receiving a call  
Calling a number in the Phone book  
Answering a phone call  
KDC-BT51U  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the Control knob.  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
The following operations disconnect the line:  
- Insering a CD.  
2 Select the Name search mode  
Turn the Control knob to select “Phone Book,  
and then press the Control knob.  
- Connecting a USB device.  
The name of the calling party is displayed if it has already  
been registered in the Phone Book.  
3 Search for Phone book  
Operation type  
Select the Phone number.  
Select the name.  
Operation  
Rejecting an incoming call  
Turn the Control knob.  
Push the Control knob towards right  
or left.  
Push the Control knob towards up  
or down.  
KDC-BT51U  
Press the [  
] button.  
KDC-5751SD KDC-5051U  
Select the initial.  
Press the [SRC] button.  
Determine the Phone number. Press the Control knob.  
4 Make a call  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the Control knob.  
Pressing [DISP] button each time switches between name  
and telephone number.  
During search, a non-accent character such as “u” is  
searched for instead of an accent character such as “ü.  
English  
|
35  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Operation of hands-free phoning  
Dialing a number  
Calling a number in the call log  
1 Enter Bluetooth mode  
KDC-BT51U  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
2 Select the Number dial mode  
2 Select the call log mode  
Turn the Control knob to select “Number Dial,  
and then press the Control knob.  
Turn the Control knob to select “Incoming  
Calls, Outgoing Calls, or “Missed Calls, and  
then press the Control knob.  
3 Enter a phone number  
Turn the Control knob to select number, and  
then Push the Control knob towards right.  
“Incoming Calls: Incoming calls  
“Outgoing Calls: Outgoing calls  
“Missed Calls: Missed calls  
4 Make a call  
3 Select a name or phone number  
KDC-BT51U  
Turn the Control knob.  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the Control knob.  
4 Make a call  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the Control knob.  
To erase the entered phone number digit by  
digit:  
Push the Control knob towards left.  
Pressing [DISP] button each time switches between name  
and telephone number.  
You can input a maximum of 32 (KCA-BT300/BT200)/ 25  
(KDC-BT51U) digits.  
The outgoing call list, the incoming call list, and the missed  
call list, are the lists of calls originated from and received  
at this unit. They are not the ones stored in the cell-phone  
memory.  
|
36 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Speed dialing (Preset dial)  
Registering to the Preset dial number  
list  
1 Enter Bluetooth mode  
KDC-BT51U  
1 Enter the phone number you wish to register  
Enter the phone number with reference to the  
following:  
Dialing a number/ Calling a number in the call log/  
Calling a number in the Phone Book  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
2 Select the Preset dial mode  
Turn the Control knob to select “Preset Call,  
and then press the Control knob.  
2 Enter Preset memory mode  
Press the [PRESET] button.  
3 Select a number and store it in the memory  
Turn the Control knob to select memory  
number (“P1” – “P6”), and then press the  
Control knob for at least 2 seconds.  
3 Select the number you want to recall from the  
memory  
Turn the Control knob to select recall number  
(“P1” – “P6”), and then press the Control knob.  
Cancelling the Preset memory mode  
4 Make a call  
Press the [  
] button.  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the Control knob.  
You need to register the preset dial number. Refer to  
<Registering to the Preset dial number list> (page 37).  
English  
|
37  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Operation of hands-free phoning  
During a call  
Call waiting  
Disconnecting a Call  
Press the [SRC] button.  
Answering another incoming call with the  
current call suspended  
KDC-BT51U  
Switching to the Private mode  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Push the Control knob towards right or left.  
Switches between Private talk (“PRIVATE”) and  
Hands-free talk each time this button is pressed.  
1) Press the Control knob.  
2) Turn the Control knob to select “Answer, and  
then press the Control knob.  
Depending on the type of your cell-phone, switching  
to the private talk mode may select the source that was  
used before commencing the hands-free connection. If  
this happens, the source cannot be switched back to the  
hands-free talk mode by operating this unit. Operate your  
cell-phone to return to the hands-free talk mode.  
Answering another Incoming call after  
terminating the current call  
Press the [SRC] button.  
Continuing the Current Call  
1) Press the Control knob.  
Adjusting the voice volume during a call  
Turn the Control knob.  
2) Turn the Control knob to select “Reject, and  
then press the Control knob.  
Answering the waiting call after terminating  
the current call  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [SRC] button.  
Switching between the current call and waiting  
call  
Press the Control knob.  
Each pressing of this knob switches the calling  
party.  
|
38 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Clearing the Disconnection message  
Making a voice dialing call  
KDC-BT51U  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“HF Disconnect” disappears.  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
2 Enter voice recognize mode  
Turn the Control knob to select “Voice  
Recognize, and then press the Control knob.  
3 Have the unit recognize your spoken name  
Press the Control knob. If you hear a beep,  
speak a registered name within 2 seconds.  
4 Have the unit recognize the spoken category  
When you hear a beep, speak the category  
within 2 seconds.  
The recognized phone number (name) is displayed.  
When you want to change the displayed phone  
number (name), press the [DISP] button.  
5 Make a call  
Press the Control knob.  
If your voice cannot be recognized, a message is displayed.  
Refer to <Troubleshooting guide> (page 54).  
Pressing the Control knob allows you to retry voice input.  
Both the name and category requires registration of a voice  
tag. Refer to <Setting a voice command for category>  
(page 49).  
English  
|
39  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Operation of hands-free phoning  
Displays of phone number type  
(category)  
The category items in the Phone Book are displayed  
as follows:  
Display  
Information  
General  
General”/  
Home  
Office  
Mobile  
Other  
Home”/  
Office”/  
Mobile”/  
Other”/  
|
40 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
English  
|
41  
Function of KCA-BT300/BT200 (Optional Accessory)  
Bluetooth audio operation  
Before Use  
Basic operation  
• You need to register your Bluetooth audio player  
before using it with this unit. For more details, see  
<Registering Bluetooth device> (page 44).  
• You need to select the Bluetooth audio player you  
wish to connect. Refer to <Selecting the Bluetooth  
device you wish to connect> (page 46).  
Selecting Bluetooth audio source  
Press the [SRC] button.  
Select the “BT AUDIO EXT” display.  
Pause and play  
Press the [  
] button.  
Music search  
Push the Control knob towards right or left.  
All or some of the operations above cannot be performed if  
the Bluetooth audio player is not ready for remote control.  
Switching between Bluetooth audio sources does not start  
or stop playback automatically. Perform the operation for  
starting or stopping playback.  
Some audio players cannot be controlled remotely or  
reconnected after Bluetooth disconnection. Operate the  
main unit of the audio player to connect Bluetooth.  
When “2Zone” is set to “ON” and “2Zone F/R Select” is set to  
“Front” of <Audio control> (page 7), Bluetooth Audio source  
cannot be selected.  
|
42 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
English  
|
43  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Bluetooth setup  
4 Select the desired Bluetooth device  
Registering Bluetooth device  
Turn the Control knob to select Bluetooth  
device, and then press the Control knob.  
KDC-BT51U  
To make your Bluetooth device (cell-phone) usable  
with this unit, you need to register it (pairing). You  
can register up to five Bluetooth devices to this unit.  
Input the PIN code (steps 5).  
KDC-5751SD KDC-5051U  
When registering from Bluetooth devices  
When “Paring Success” is displayed, PIN code input  
(steps 5) is not required.  
1 Turn on the this unit.  
When “Pin Code NG” is displayed, press the Control  
knob. Then enter the PIN code (steps 5).  
2 Start registering a unit by operating the  
Bluetooth device  
By operating the Bluetooth device, register the  
hands-free unit (pairing). Select “KENWOOD BT  
CD/R-3P1, KCA-BT300, or “KCA-BT200” from the list  
of connected units.  
5 Input the PIN code  
Operation type  
Select the numbers.  
Move to the next digit.  
Delete the last digit.  
Transmit the PIN code.  
Operation  
Turn the Control knob.  
Push the Control knob towards right.  
Push the Control knob towards left.  
Press the Control knob.  
3 Enter a PIN code  
Input the PIN code registered as mentioned in  
<Registering PIN Code> (page 45).  
Check that registration is complete on the  
Bluetooth device.  
If “Pairing Success” is displayed, registration is  
complete.  
6 Return to the device list  
Press the Control knob.  
4 By operating the Bluetooth device, start hands-  
free connection.  
7 Exit Bluetooth mode  
Press the [SRC] button.  
When registering from this unit  
1 Enter Bluetooth mode  
KDC-BT51U  
This unit allows up to eight digits to be input for a PIN code.  
If a PIN code cannot be input from this unit, it can be input  
from the Bluetooth device.  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
If there are 5 Bluetooth devices registered, you cannot  
register a new Bluetooth device.  
If the error message appears even though the PIN code is  
correct, try <Registering Special bluetooth device> (page 45).  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select Bluetooth device registration mode  
The item can be selected and determined as  
follows.  
“Settings” > “Pairing” > “Device Registration”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
Search for the Bluetooth device.  
When search is completed, “Finished” is displayed.  
|
44 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Registering Special bluetooth device  
Registering PIN Code  
Allow registration of a special device that cannot be  
registered normally (pairing).  
By operating the Bluetooth device, specify the PIN  
code necessary for registering this unit.  
1 Enter Bluetooth mode  
KDC-BT51U  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select Special device registration mode  
The item can be selected and determined as  
follows.  
3 Select PIN code edit mode  
The item can be selected and determined as  
follows.  
“Settings” > “Pairing” > “SPCL Device Select”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
“Settings” > “Detailed Settings” >  
“PIN Code Edit”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
4 Select a desired device name  
Turn the Control knob to select device name,  
and then press the Control knob.  
If “Completed” is displayed, registration is  
completed.  
4 Input the PIN code  
Operation type  
Operation  
Select the numbers.  
Move to the next digit.  
Delete the last digit.  
Transmit the PIN code.  
Turn the Control knob.  
Push the Control knob towards right.  
Push the Control knob towards left.  
Press the Control knob.  
5 Go through the procedure of <Registering  
Bluetooth device> (page 44) and complete the  
registration (pairing).  
If “Completed” is displayed, registration is complete.  
5 Exit Bluetooth mode  
Press the [SRC] button.  
Cancelling Bluetooth mode  
Press the [SRC] button.  
By default, “0000” is specified.  
If the device name is not in the list, select “Other Phones.  
A PIN code can be specified with up to eight digits.  
English  
|
45  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Bluetooth setup  
Downloading the Phone book  
Selecting the Bluetooth device you  
wish to connect  
Download the phone book data from the cell-  
phone to this unit so that you can use the Phone  
Book of this unit.  
When two or more Bluetooth devices have already  
been registered, you need to select the Bluetooth  
device you wish to use.  
Downloading automatically  
If the cell-phone supports a phone book  
synchronization function, the phone book is  
downloaded automatically after Bluetooth  
connection.  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
Setting on the cell-phone may be required.  
If no phone book data is found in the unit even after the  
“Completed” is displayed, your cell-phone may not support  
automatic download of phone book data. In this case, try  
downloading manually.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select Bluetooth device selection mode  
The item can be selected and determined as  
follows.  
“Settings” > “Pairing” > “Phone Selection” (to  
select the cell-phone) or “Audio Selection” (to  
select the audio player)  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
“(name)” is displayed.  
Downloading from the cell-phone manually  
1 Operate the cell-phone to end the hands-free  
connection.  
2 Operate the cell-phone to send the phone  
book data to this unit  
By operating the cell-phone, download the phone  
book data to this unit.  
• During downloading:  
“Downloading” is displayed.  
• After completion of downloading:  
“Completed” is displayed.  
4 Select a desired Bluetooth device  
Turn the Control knob to select Bluetooth  
device name, and then press the Control knob.  
(name)’ or ‘-(name)’ is displayed.  
”: The selected Bluetooth device is busy.  
“-”: The selected Bluetooth device is on standby.  
“ “ (blank): The Bluetooth device is deselected.  
3 Operate the cell-phone to start the hands-free  
connection.  
Clearing the downloading completion message  
Press any button.  
5 Exit Bluetooth mode  
Press the [SRC] button.  
Up to 1000 phone numbers can be registered for each  
registered cell-phone.  
If a cell-phone is already selected, deselect it, and then  
select a different one.  
Up to 32 digits can be registered for each phone number  
along with up to 50* characters representing a name.  
(* 50: Number of alphabetic alphabetical characters.  
Fewer characters can be input depending on the type of  
characters.)  
If you cannot select a device using the audio player,  
connect the device with the audio player.  
To cancel downloading of the phone book data, operate  
the cell-phone.  
|
46 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Deleting a registered Bluetooth  
device  
Displaying the firmware version  
Display the version of the firmware of this unit.  
You can delete a registered Bluetooth device.  
1 Enter Bluetooth mode  
KDC-BT51U  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select Bluetooth firmware update mode  
The item can be selected and determined as  
follows.  
“Settings” > “Detailed Settings” >  
“BT F/W Update”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
The firmware version appears.  
3 Select Bluetooth device deletion mode  
The item can be selected and determined as  
follows.  
“Settings” > “Pairing” > “Device Delete”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
Device name is displayed.  
4 Exit Bluetooth mode  
4 Delete the selected Bluetooth device  
Turn the Control knob to select device name,  
and then press the Control knob.  
Press the [SRC] button.  
For how to update the firmware, access our web site.  
5 Turn the Control knob to select “YES, and then  
press the Control knob.  
“Completed” is displayed.  
6 Exit Bluetooth mode  
Press the [SRC] button.  
When a registered cell-phone is deleted, its Phone Book,  
log, SMS, and voice tag are also deleted.  
English  
|
47  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Bluetooth setup  
Pressing the Control knob allows you to retry voice input.  
Adding a voice dialing command  
Selecting “Check” (Play)  
Add a voice tag to the phonebook for voice dialing.  
You can register up to 35 voice tags.  
6 Press the Control knob.  
Play the registered voice and return to step 2.  
1 Enter Bluetooth mode  
KDC-BT51U  
Selecting “Delete” (Delete)  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
6 Delete a voice tag  
Press the Control knob.  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
7 Turn the Control knob to select “YES, and then  
press the Control knob.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
Exit Bluetooth mode  
Press the [SRC] button.  
3 Select Phonebook name edit mode  
The item can be selected and determined as  
follows.  
“Settings” > “Voice Tag” > “PB Name Edit”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
4 Search for the name to register  
Turn the Control knob to select name, and then  
press the Control knob.  
If a voice tag has already been registered for a  
name, “*” is displayed before the name.  
5 Select a mode  
Turn the Control knob.  
Display  
Operation  
“Register”  
“Check”*  
“Delete”*  
Register a voice tag.  
Play a voice tag.  
Delete a voice tag.  
*Displayed only when a name for which a voice tag has  
been registered is selected.  
Selecting “Register” (Regist)  
6 Register a voice tag (first)  
Press the Control knob. When you hear a beep,  
speak the voice tag within 2 seconds.  
7 Confirm the voice tag (second)  
Press the Control knob. When you hear a  
beep, speak the same voice tag again within 2  
seconds.  
“Completed” is displayed.  
8 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
Return to step 2. You can register another voice tag  
continuously.  
If your voice cannot be recognized, a message is displayed.  
(Refer to <Troubleshooting guide> (page 54))  
|
48 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Setting a voice command for category  
Add a voice tag to the phone number category  
(type) for voice calling.  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
3 Select Phonebook type edit mode  
The item can be selected and determined as  
follows.  
“Settings” > “Voice Tag” > “PN Type Edit”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
4 Select the category (type) you wish to set  
Turn the Control knob to select category name,  
and then press the Control knob.  
“General”/ “Home”/ “Office”/ “Mobile”/ “Other”  
5 Select a mode  
Turn the Control knob.  
Display  
Operation  
“Register”  
“Check”*  
“Delete”*  
Register a voice tag.  
Play a voice tag.  
Delete a voice tag.  
*KCA-BT300/BT200 only. Displayed only when a name for  
which a voice tag has been registered is selected.  
6 Register the category (type) by performing  
steps 6 to 7 in <Adding a voice dialing  
command> (page 48).  
7 Exit Bluetooth mode  
Press the [SRC] button.  
Set the voice tag for all the 5 categories. If the voice tag is  
not registered for all the categories, the Phonebook may  
not be recalled by voice command.  
English  
|
49  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
Bluetooth setup  
“MIC Gain”  
Adjusts the sensitivity of the built-in  
microphone for a telephone call. Adjust the  
voice of caller. Setting to“+”increases the  
voice volume.  
Function of the KDC-BT51U  
“-3” – ”0” – “+3”  
Bluetooth detail setting  
Configures initial settings of this unit.  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
“NR Level”  
SReduces the noises generated by surrounding  
environment without changing the built-in  
microphone volume. Adjust the voice of caller  
when it is not clear. Setting to“+”increases  
the noise reduction.  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
Function of the KDC-BT51U  
“-3” – ”0” – “+3”  
Sets the echo cancellation level.  
Function of the KDC-BT51U  
“-2” – ”0” – “+2”  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
“Echo Cancel”  
3 Select Bluetooth detail setting mode  
The item can be selected and determined as  
follows.  
(
: Factory setting)  
“Settings” > “Detailed Settings”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
5 Set the Bluetooth detail setting item  
Turn the Control knob to select desired value,  
and then press the Control knob.  
The previous item is displayed.  
4 Select the desired Bluetooth detail setting  
item  
Turn the Control knob to select Bluetooth detail  
setting item, and then press the Control knob.  
6 Exit Function setting mode  
Press the [  
] button for at least 1 second.  
Display  
Overview  
“Detailed Settings”  
“Auto Answer”  
This function automatically answers (responds  
to) a call after lapse of the preset time interval  
for automatic answer.  
“OFF”: Does not answer the phone call  
automatically.  
“0”: Automatically answers the phone call  
at once.  
“1SEC” – “8SEC” – “99SEC”:  
Automatically answers the phone call after  
lapse of 1 – 99 seconds.  
“Auto Reconnect” WhenON”is selected, re-pairing with the  
registered Bluetooth device starts automatically  
when pairing is disconnected.  
“ON” / “OFF”  
“Bluetooth HF”  
“Bluetooth HF/  
Audio”  
You can specify output speakers for hands-free  
voice communication and Bluetooth audio  
sound.  
“Front” : Outputs sound from the front  
speakers.  
“All” : Outputs sound from the front and rear  
speakers.  
“Call Beep”  
You can output a beep from the speaker when  
a call comes in.  
“ON” : Beep is heard.  
“OFF” : Beep is canceled.  
|
50 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Function of KDC-BT51U, KCA-BT300/BT200 (Optional Accessory)  
SMS (Short Message Service)  
Displaying the SMS  
Downloading the SMS  
The SMS received by at the cell-phone is displayed  
on the receiver.  
Download the short message (SMS) received by the  
cell-phone so that it can be read on this unit.  
A newly received message is displayed.  
1 Enter Bluetooth mode  
KDC-BT51U  
¤
To prevent car accidents, the driver should not read the  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
SMS while driving.  
Press the [LOG] button for at least 1 second.  
“BT MODE” is displayed.  
When a new message arrives  
“SMS Received” is displayed.  
The display disappears with any operations.  
2 Enter Function setting mode  
Press the Control knob for at least 1 second.  
Displaying the SMS  
3 Select SMS download mode  
The item can be selected and determined as  
follows.  
1 Enter Bluetooth mode  
KDC-BT51U  
Press the [ ] button.  
KDC-5751SD KDC-5051U  
“Settings” > “SMS Download”  
To select the item, turn the Control knob. To  
determine the item, press the Control knob.  
Press the [LOG] button for at least 1 second.  
2 Select SMS inbox display mode  
Turn the Control knob to select “SMS Inbox,  
and then press the Control knob.  
4 Start downloading  
Press the Control knob.  
“SMS Downloading” is displayed.  
When the downloading finishes, “Completed” is  
displayed.  
3 Select a message  
Turn the Control knob.  
Each press of the [DISP] button switches between  
displaying the telephone number or name and  
message reception date.  
5 Exit Bluetooth mode  
Press the [SRC] button.  
4 Display the text  
The cell-phone must be able to transmit the SMS using  
Bluetooth. Setting on the cell-phone may be required. If  
the cell-phone does not support SMS function, the SMS  
download item in Function Control mode is not displayed.  
When the SMS is downloaded from the cell-phone, the  
unopened messages in the cell-phone are opened.  
The up to 75 already-read and unread short messages  
respectively can be downloaded.  
Press the Control knob.  
Turn the Control knob to scroll through the  
message.  
Press the Control knob to return to the message  
list screen.  
5 Exit Bluetooth mode  
Press the [SRC] button.  
The unopened message is displayed at the beginning of the  
list. Other messages are displayed in the order of reception.  
The SMS that are received when the cell-phone is not linked  
with Bluetooth cannot be displayed. Download the SMS.  
The short message cannot be displayed during  
downloading the SMS.  
English  
|
51  
Appendix  
About Audio file  
About USB device  
Playable Audio file  
• When the USB device is connected to this unit,  
it can be charged up provided that this unit is  
powered.  
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)  
Playable disc media  
CD-R/RW/ROM  
Playable disc file format  
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.  
Playable USB device  
USB mass storage class  
Playable USB device and SD card file system  
• Install the USB device in the place where it will not  
prevent you from driving your vehicle properly.  
• You cannot connect a USB device via a USB hub and  
Multi Card Reader.  
• Save backups of the audio files used with this unit.  
The files can be erased depending on the operating  
conditions of the USB device.  
We shall have no compensation for any damage  
arising out of erasure of the stored data.  
• No USB device comes with this unit. You need to  
purchase a commercially available USB device.  
• When connecting the USB device, usage of the  
CA-U1EX (option) is recommended.  
• Normal playback is not guaranteed when a cable  
other than the USB compatible cable is used.  
Connecting a cable whose total length is longer  
than 4 m can result in abnormal playback.  
FAT16, FAT32  
Even if the audio files comply with the standards listed  
above, the play may be impossible depending on the  
types or conditions of media or device.  
Playing order of the Audio file  
In the example of folder/file tree shown below, the  
files are played in the order from to .  
^
¡
: Folder  
Folder  
CD  
(1)  
:
A
udiofile  
¡!  
2
3
¡"  
¡#  
iPod/iPhone that can be connected to this  
unit  
Made for  
• iPod nano (6th generation) • iPod nano (5th generation)  
• iPod nano (4th generation) • iPod nano (3rd generation)  
• iPod nano (2nd generation) • iPod nano (1st generation)  
• iPod with video  
• iPod touch (4th generation) • iPod touch (3rd generation)  
• iPod touch (2nd generation) • iPod touch (1st generation)  
4
¡$  
5
¡%  
¡P  
• iPod classic  
An online manual about audio files is put on the site,  
manual, detailed information and notes which are not  
written in this manual are provided. Make sure to read  
through the online manual as well.  
• iPhone 4  
• iPhone 3G  
• iPhone 3GS  
• iPhone  
• For information on the compatibility of iPod/iPhone  
software, visit www.kenwood.com/cs/ce/ipod/.  
• Type of control available varies depending  
on the type of connected iPod. See  
www.kenwood.com/cs/ce/ipod/ for further details.  
• The word “iPod” appearing in this manual indicates  
the iPod or the iPhone connected with the iPod  
connection cable* (optional accessory).  
* Not supported model KCA-iP500.  
• Refer to the web site for connectable iPod and iPod  
connection cable.  
In this manual, the word “USB device” is used for flash  
memories and digital audio players which have USB  
terminals.  
About SD card  
• This unit is capable of playback of SD/SDHC  
memory cards complying with the SD or SDHC  
standard.  
SD card (≤2 GB), SDHC card (≤32 GB)  
• A special adapter is required to use a miniSD card,  
miniSDHC card, microSD card or microSDHC card.  
• The MultiMedia Card (MMC) cannot be used.  
• Data recorded in the SD audio format cannot be  
played back.  
If you start playback after connecting the iPod, the music  
that was playing on the iPod is played first.  
In this case, “RESUMING” is displayed without displaying a  
folder name, etc. Changing the browse item will display a  
correct title, etc.  
You cannot operate iPod if “KENWOOD” or “” displayed on  
iPod.  
|
52 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Function of KDC-BT51U  
About “KENWOOD Music Editor”  
• This unit supports the PC application “KENWOOD  
Music Editor Light ver1.1” or later.  
• When you use the audio file with database  
information added by the “KENWOOD Music Editor  
Light ver1.1, you can search a file by title, album or  
artist name using the <Music search> (page 14).  
About the Cell-phone  
This unit conforms to the following Bluetooth  
specifications:  
Version  
Profile  
Bluetooth Ver. 2.0 Certified  
HFP (Hands Free Profile)  
HSP (Headset Profile)  
SPP (Serial Port Profile)  
• In the Instruction manual, the term “Music Editor  
media” is used to mean the device that contains  
audio files with database information added with  
KENWOOD Music Editor.  
PBAP (Phonebook Access Profile)  
OPP (Object Push Profile)  
SYNC (Synchronization Profile)  
• “KENWOOD Music Editor Light ver1.1” is available  
from the following web site:  
• For further information on “KENWOOD Music  
Editor Light ver1.1, refer to the site above or the  
application help.  
For the cell-phones verified for compatibility, access  
the following URL:  
The units supporting the Bluetooth function have been  
certified for conformity with the Bluetooth Standard  
following the procedure prescribed by Bluetooth  
SIG. However, it may be impossible for such units to  
communicate with your cell-phone depending on its type.  
HFP is a profile used to make a hands-free call.  
OPP is a profile used to transfer data such as a phone book  
between units.  
English  
|
53  
Troubleshooting guide  
Some functions of this unit may be disabled by  
some settings made on this unit.  
The messages shown below display your  
systems condition.  
TOC Error:  
• No disc has been loaded in the disc  
magazine.  
• The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
!
!
• Cannot set up Display.  
<Demonstration mode Setting> (page 32) is not set to  
Off.  
Error 05:  
Error 77:  
The disc is unreadable.  
• Cannot set up “Text Select, Side Select, and  
“Status” of “Display Select.  
<Selecting display type> (page 24) is set to Displays  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the  
“Error 77” code does not disappear, consult  
your nearest service center.  
off.  
!
!
• Cannot set up the subwoofer.  
• Cannot set up the low pass filter.  
• No output from the subwoofer.  
“SubWoofer” of <Audio control> (page 7) is not set to  
On.  
Mecha Error: Something is wrong with the disc magazine.  
Or the unit is malfunctioning for some reason.  
Check the disc magazine. And then press  
the reset button on the unit. If the “Mecha  
Error” code does not disappear, consult  
your nearest service center.  
Cannot set up the subwoofer Phase.  
“LPF SubWoofer” of <Audio control> (page 7) is set to  
“Through.  
IN (Blink):  
The CD player section is not operating  
properly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
Protect (Blink): The speaker wire has a short-circuit or  
touches the chassis of the vehicle, and then  
the protection function is activated.  
General  
? The Key beep does not sound  
Wire or insulate the speaker cable properly  
and press the reset button. If the “Protect”  
code does not disappear, consult your  
nearest service center.  
The preout jack is being used.  
The Key beep cannot be output from the preout  
jack.  
NA File:  
An Audio file is played with a format that this  
unit can’t support.  
Tuner source  
? Radio reception is poor.  
Copy PRO:  
Read Error:  
A copy-protected file is played.  
The car antenna is not extended.  
Pull the antenna out all the way.  
The file system of the connected USB device  
is broken.  
Copy the files and folders for the USB  
device again. If the error message is still  
displayed, initialize the USB device or use  
other USB devices.  
Disc source  
? The specified disc does not play, but another one  
plays instead.  
The specified CD is quite dirty.  
Clean the CD, referring to the CD cleaning of the  
section on <Handling discs> (page 4).  
No Device:  
N/A Device:  
The USB device is selected as a source  
although no USB device is connected.  
Change the source to any source other  
than USB. Connect an USB device, and  
change the source to USB again.  
The disc is severely scratched.  
Try another disc instead.  
Audio file source  
• An unsupported USB device is connected.  
• Connection to the iPod has failed.  
Check that the connected iPod is an iPod  
that is supported. See <About Audio file>  
(page 52) for information on supported  
iPods.  
? The sound skips when an Audio file is being  
played.  
The media is scratched or dirty.  
Clean the media, referring to the CD cleaning of  
the section on <Handling discs> (page 4).  
The recording condition is bad.  
Record the media again or use another media.  
|
54 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
No Music Data/Error 15:  
• The connected USB device contains no  
Too Long:  
The word or utterance is too long to be  
recognized.  
playable audio file.  
• Media was played that does not have data  
recorded that the unit can play.  
No Phonebook: Data is not contained in the phone book.  
No Message: No short message in In Box.  
USB ERROR:  
iPod Error:  
Some trouble may have occurred to the  
connected USB device.  
Remove the USB device, then cycle the  
power switch to ON. If the same display is  
repeated, use another USB device.  
No Record:  
The voice tag is not registered in the  
phonebook.  
Memory Full: The number of voice tags reaches the  
maximum number to be registered in the  
phonebook.  
Connection to the iPod has failed.  
Remove the USB device and then  
reconnect it.  
Confirm that the software for the iPod is  
the latest version.  
LOG: No Memory:  
The procedure is not registered to Log Preset  
Memory.  
No Access:  
The procedure preset with Log Preset  
Memory cannot be available. The preset  
content may not be recalled depending on  
the selected source or mode.  
Reset iPod/ iPhone.  
No Number:  
No Data:  
• The calling party does not notify a caller ID.  
• There is no phone number data.  
• There is no outgoing call list.  
• There is no incoming call list.  
• There is no missed call list.  
• There is no phone book list.  
No Voice:  
No call.  
Memory Full: The tag memory of HD Radio is FULL.  
iPod Full: The iPod memory is FULL.  
No Entry:  
The cell-phone has not been registered  
(pairing).  
N/A Channels: No receivable channel and category.  
HF Disconnect: The unit cannot communicate with the cell-  
phone.  
HF Error 07:  
The memory cannot be accessed.  
Turn off the power and on again. If this  
message still appears, press the reset  
button on the control unit.  
HF Error 68:  
The unit cannot communicate with the cell-  
phone.  
Turn off the power and on again. If this  
message still appears, press the reset  
button on the control unit.  
Unknown:  
The Bluetooth device cannot be detected.  
Device Full:  
5 Bluetooth device have already been  
registered. No more Bluetooth devices are  
registered.  
PIN Code NG: The PIN code is wrong.  
Connect NG: The unit cannot be connected to the device.  
Pairing Failed: Pairing error.  
Err No Matching:  
The voice tag is wrong. Voice cannot be  
recognized because of an unregistered voice  
tag, etc.  
Too Soft:  
Voice is too small and cannot be recognized.  
Voice is too large to be recognized.  
Too Loud:  
English  
|
55  
Specifications  
FM tuner section  
USB Interface  
Frequency range (50 kHz step)  
: 87.5 MHz – 108.0 MHz  
USB Standard  
: USB1.1/ 2.0 (Full speed)  
Usable sensitivity (S/N = 26dB)  
: 1 μV/75 Ω  
File System  
: FAT16/ 32  
Quieting Sensitivity (S/N = 46dB)  
: 2.5 μV/75 Ω  
Maximum Supply current  
: 500 mA  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
Signal to Noise ratio (MONO)  
: 63 dB  
WMA decode  
: Compliant with Windows Media Audio  
Stereo separation (1 kHz)  
: 40 dB  
AAC decode  
: AAC-LC .m4a” files  
MW tuner section  
Bluetooth section (KDC-BT51U)  
Frequency range (9 kHz step)  
: 531 kHz – 1611 kHz  
Version  
: Bluetooth Ver. 2.0 Certified  
Usable sensitivity (S/N = 20dB)  
: 36 µV  
Frequency range  
: 2.402 – 2.480 GHz  
Output Power  
: +4dBm (MAX), 0dBm (AVE) Power Class 2  
Maximum Communication range  
: Line of sight approx.10m (32.8 ft)  
Profiles  
: HFP (Hands Free Profile)  
: HSP (Headset Profile)  
LW tuner section  
Frequency range  
: 153 kHz – 279 kHz  
Usable sensitivity (S/N = 20dB)  
: 57 µV  
: SPP (Serial Port Profile)  
CD player section  
Laser diode  
: GaAlAs  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 24 Bit  
Spindle speed  
: 500 – 200 rpm (CLV)  
Wow & Flutter  
: Below Measurable Limit  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz)  
: 0.008 %  
Signal to Noise ratio (1 kHz)  
: 110 dB  
: PBAP (Phonebook Access Profile)  
: OPP (Object Push Profile)  
: SYNC (Synchronization Profile)  
Audio section  
Maximum output power  
: 50 W x 4  
PWR DIN45324,+B=14.4V  
: 30 W x 4  
Speaker Impedance  
: 4 – 8 Ω  
Tone action  
Bass : 100 Hz 8 dB  
Middle : 1 kHz 8 dB  
Treble : 12.5 kHz 8 dB  
Preout level / Load (CD)  
: 2500 mV/10 kΩ  
Preout impedance  
: ≤ 600 Ω  
Dynamic range  
: 93 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
AAC decode  
: AAC-LC .m4a” files  
|
56 KDC-BT51U/ KDC-5751SD/ KDC-5051U  
Auxiliary input  
Frequency response ( 3 dB)  
: 20 Hz – 20 kHz  
Input Maximum Voltage  
: 1200 mV  
Input Impedance  
: 10 kΩ  
General  
Operating voltage  
KDC-BT51U : 14.4 V (10.5 – 16V allowable)  
KDC-5751SD/ KDC-5051U  
: 14.4 V (11 – 16V allowable)  
Maximum Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 53 x 160 mm  
Weight  
: 1.3 kg  
Specifications subject to change without notice.  
English  
|
57  
This Product is not installed by the manufacturer of a  
vehicle on the production line, nor by the professional  
importer of a vehicle into an EU Member State.  
The Bluetooth word mark and logos are owned by  
the Bluetooth SIG, Inc. and any use of such marks  
by Kenwood Corporation is under license. Other  
trademarks and trade names are those of their  
respective owners.  
Information on Disposal of Old Electrical and  
Electronic Equipment and Batteries (applicable  
for EU countries that have adopted separate  
waste collection systems)  
The “AAC” logo is a trademark of Dolby Laboratories.  
iTunes is a trademark of Apple Inc.  
“Made for iPod” and “Made for iPhone” mean that an  
electronic accessory has been designed to connect  
specifically to iPod or iPhone, respectively, and has  
been certified by the developer to meet Apple  
performance standards. Apple is not responsible for  
the operation of this device or its compliance with  
safety and regulatory standards. Please note that the  
use of this accessory with iPod or iPhone may affect  
wireless performance.  
iPhone, iPod, iPod classic, iPod nano, and iPod touch  
are trademarks of Apple Inc., registered in the U.S. and  
other countries.  
“Adobe Reader” is a trademark of Adobe Systems  
Incorporated.  
Products and batteries with the symbol (crossed-  
out wheeled bin) cannot be disposed as  
household waste.  
Old electrical and electronic equipment and  
batteries should be recycled at a facility capable  
of handling these items and their waste  
byproducts.  
Contact your local authority for details in locating  
a recycle facility nearest to you.  
Proper recycling and waste disposal will help  
conserve resources whilst preventing detrimental  
effects on our health and the environment.  
Notice: The sign “Pb” below the symbol for  
batteries indicates that this battery  
contains lead.  
SDHC Logo is a trademark of SD-3C, LLC.  
The marking of products using lasers  
CLASS 1  
LASER PRODUCT  
The label is attached to the chassis/case and says  
that the component uses laser beams that have been  
classified as Class 1. It means that the unit is utilizing  
laser beams that are of a weaker class. There is no  
danger of hazardous radiation outside the unit.  
This symbol mark indicates that Kenwood  
manufactured this product so as to  
decrease harmful influence on the  
environment.  
Magyar  
Declaration of Conformity with regard to  
the EMC Directive 2004/108/EC  
Alulírott, Kenwood, kijelenti, hogy a jelen KDC-BT51U megfelel az 1999/5/EC  
irányelvben meghatározott alapvető követelményeknek és egyéb vonatkozó  
előírásoknak.  
Svenska  
For KDC-BT51U:  
Declaration of Conformity with regard to  
the R&TTE Directive 1999/5/EC  
Manufacturer:  
Kenwood Corporation  
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan  
Härmed intygar Kenwood att denna KDC-BT51U stär l överensstämelse med de  
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av  
direktiv 1999/5/EG.  
Suomi  
Kenwood vakuuttaa täten että KDC-BT51U tyyppinen laite on direktiivin  
1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen  
mukainen.  
EU Representative's:  
Kenwood Electronics Europe BV  
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands  
Slovensko  
S tem Kenwood izjavlja, da je ta KDC-BT51U v skladu z osnovnimi zahtevami in  
ostalimi ustreznimi predpisi Direktive 1999/5/EC.  
Slovensky  
Spoločnosť Kenwood týmto vyhlasuje, že KDC-BT51U spĺňa zákldné požiadavky  
a ďalšie prislušné ustanovenia Direktĺvy 1999/5/EC.  
English  
Dansk  
Undertegnede Kenwood erklærer harved, at følgende udstyr KDC-BT51U  
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.  
Ελληνικά  
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Kenwood ΔΗΛΩΝΕΙ ΟΤΙ KDC-BT51U ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ  
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ  
1999/5/EK.  
Hereby, Kenwood declares that this unit KDC-BT51U is in compliance with the  
essential requirements and other relevant provisions of Directive 1999/5/EC.  
Français  
Par la présente Kenwood déclare que l’appareil KDC-BT51U est conforme aux  
exigences essentielles et aux autres dispositions pertinentes de la directive  
1999/5/CE.  
Par la présente, Kenwood déclare que ce KDC-BT51U est conforme aux  
exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui  
lui sont applicables.  
Eesti  
Sellega kinnitab Kenwood, et see KDC-BT51U vastab direktiivi 1999/5/EC  
põhilistele nõudmistele ja muudele asjakohastele määrustele.  
Deutsch  
Latviešu  
Hiermit erklärt Kenwood, dass sich dieser KDC-BT51U in Übereinstimmung mit  
den grundlegenden Anforderungen und den anderen relevanten Vorschriften  
der Richtlinie 1999/5/EG befindet. (BMWi)  
Ar šo, Kenwood, apstiprina, ka KDC-BT51U atbilst Direktīvas 1999/5/EK  
galvenajām prasībām un citiem tās nosacījumiem.  
Lietuviškai  
Hiermit erklärt Kenwood die Übereinstimmung des Gerätes KDC-BT51U mit den  
grundlegenden Anforderungen und den anderen relevanten Festlegungen der  
Richitlinie 1999/5/EG. (Wien)  
Šiuo, Kenwood, pareiškia, kad šis KDC-BT51U atitinka pagrindinius Direktyvos  
1999/5/EB reikalavimus ir kitas svarbias nuostatas.  
Malti  
Nederlands  
Hawnhekk, Kenwood, jiddikjara li dan KDC-BT51U jikkonforma mal-ħtiġijiet  
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/  
EC.  
Hierbij verklaart Kenwood dat het toestel KDC-BT51U in overeenstemming  
is met de essentiële eisen en de andere relevante bepalingen van richtlijn  
1999/5/EG.  
Українська  
Bij deze verklaat Kenwood dat deze KDC-BT51U voldoet aan de essentiële eisen  
en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.  
Компанія Kenwood заявляє, що цей виріб KDC-BT51U відповідає ключовим  
вимогам та іншим пов’язаним положенням Директиви 1999/5/EC.  
Italiano  
Turkish  
Con la presente Kenwood dichiara che questo KDC-BT51U è conforme ai  
requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva  
1999/5/CE.  
Kenwood, işbu belge ile KDC-BT51U numaralı bu ünitenin 1999/5/EC  
Direktifi’nin özel gereksinimlerine ve ilgili diğer hükümlerine uygun olduğunu  
beyan eder.  
Español  
Por medio de la presente Kenwood declara que el KDC-BT51U cumple con los  
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de  
la Directiva 1999/5/CE.  
Português  
Kenwood declara que este KDC-BT51U está conforme com os requisitos  
essenciais e outras disposições da Directiva 1999/5/CE.  
Polska  
For Turkey  
Kenwood niniejszym oświadcza, że KDC-BT51U spełnia zasadnicze wymogi  
oraz inne istotne postanowienia dyrektywy 1999/5/EC.  
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli  
ve Elektronik Eşyalarda Bazı Zararlı Maddelerin Kullanımının  
Sınırlandırılmasına Dair Yönetmeliğe uygun olarak üretilmiştir.  
Český  
Kenwood timto prohlasuje, ze KDC-BT51U je ve shode se zakladnimi pozadavky  
a s dalsimi prislusnymi ustanoveni Narizeni vlady c. 426/2000 Sb.  
This product complies with Directive, Number 26891  
regarding “REGULATION ON THE RESTRICTION OF THE USE  
OF CERTAIN HAZARDOUS SUBSTANCES IN LECTRICAL AND  
ELECTRONIC EQUIPMENT.  

Pioneer XDV P90 User Manual
Philips Car Video System 200VW8FB User Manual
Panasonic HHR150AA User Manual
Panasonic Blu ray Player BP325N User Manual
Metz 36 AF 4C User Manual
Leupold VX 3 User Manual
Laney Amplification Car Amplifier AH100 User Manual
KitchenAid 4KFP750CR0 User Manual
Kenwood KDV MP7439 User Manual
Kenwood KAC 7205 User Manual