Kenwood DNX7120 User Manual

GPS NAVIGATION SYSTEM

DNX7120

MONITOR WITH DVD RECEIVER

DDX712

DDX7032

INSTRUCTION MANUAL

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best

performance from your new GPS Navigation System/ DVD Receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the

warranty card, and in the space provided below. Refer to the model and serial numbers

whenever you call upon your Kenwood dealer for information or service on the product.

Model DNX7120/DDX712/DDX7032 Serial number

US Residence Only

www.Kenwoodusa.com

Muting Audio Volume upon Reception

Hands Free Unit Control

Control Screen Function

When Received a Call

Calling by Entering a Phone Number

Quick Dialing

of Phone call

Character Entry

Controlling tone-based services

Calling by Phonebook

How To Use the Character Entry Screen

Making a Call Using Outgoing/Incoming Call

Records

Screen Control

Calling by Voice Recognition

Setting Up the Hands Free Phone

Voice Registration

Key Word Voice Registration

Phone Number Preset

SMS (Short Message Service)

Remote Controller

Setup Menu

Battery installation

Setup Menu

Remote Controller mode switch

Common operations (AUD mode)

DVD/VCD/CD/Audio files (DVD mode)

Radio (AUD mode)

NAVI (NAVI mode)

TV (TV mode)

Audio Setup

Crossover Network Setup

DVD Setup

Language Setup

Parental Level Setup

System Setup

AV Interface Setup

User Interface

Direct Source Button Setup

Entering Background

Background Delete

Background Select

Touch Panel Adjustment

Clock Setup

Audio Control

Audio Control Menu

Audio Control

Equalizer Control

Tone Setup

Monitor Setup

Security Code Setup

Deactivating Security Code

iPod Setup

Zone Control

Sirius Setup

Sirius Parental Code Setup

Sirius Parental Lock Setup

Sirius Parental Lock Channel Select

Bluetooth Setup

Registering Bluetooth Unit

Registering Bluetooth Unit PIN Code

Registering Special Bluetooth Unit

Bluetooth Unit Connection

Deleting Bluetooth Unit

DivX Setup

DVD Language Codes

Help? Troubleshooting

Help? Error

Specifications

100

Setup Memory

EXT SW Setup

English

How to read this manual

This manual uses illustrations to explain its

operations.

Seek Mode

The displays and panels shown in this manual

are examples used to provide clear explanations

of the operations.

Sets a station selection.

For this reason, they may be different from the

actual displays or panels used, or some display

patterns may be different.

The mode is switched in following order each

time you touch the button.

Display

Setting

"AUTO1"

Tunes in a station with good reception

automatically.

"AUTO2"

"MANU"

Tunes in stations in memory one after another.

Switches to the next frequency manually.

Manual Memory

Stores the current receiving station in memory.

Select a station you wish to store in

memory

Store in memory

Continue to touch until the memory number

appears.

Next page 3

The above operation example with the mark

differs from the actual operation.

DNX7120/DDX712/DDX7032

English

Before Use

Handling discs

2WARNING

• Do not touch the recording surface of the disc.

• Do not stick tape etc. on the disc, or use a disc with

tape stuck on it.

• Do not use disc type accessories.

• Clean from the center of the disc and move

outward.

To prevent injury or fire, take the following

precautions:

• To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools) inside

the unit.

• Do not watch or fix your eyes on the unit’s display

when you are driving for any extended period.

• When removing discs from this unit, pull them out

horizontally.

• If the disc center hole or outside rim has burrs,

use the disc only after removing the burrs with a

ballpoint pen etc.

How to reset your unit

• If the unit or the connected unit (disc auto

changer, etc.) fails to operate properly, press the

Reset button. The unit returns to factory settings

when the Reset button is pressed.

Discs that cannot be used

• Discs that are not round cannot be used.

• Remove the USB device before pressing the Reset

button. Pressing the Reset button with the USB

device installed can damage the data contained in

the USB device. For how to remove the USB device,

refer to <Playing a USB device> (page 10).

• Discs with coloring on the recording surface or

discs that are dirty cannot be used.

• This unit can only play the CDs with

This unit may not correctly play discs which do not

have the mark.

• You cannot play a CD-R or CD-RW that has not

been finalized. (For the finalization process refer to

your CD-R/CD-RW writing software, and your CD-

R/CD-RW recorder instruction manual.)

Reset button

Cleaning the Unit

• If you try to load a 3-inch-disc with its adapter into

the unit, the adapter might separate from the disc

and damage the unit.

If the faceplate of this unit is stained, wipe it with a

dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain off

with a cloth moistened with neutral cleaner, then

wipe it again with a clean soft dry cloth.

Other notes

• If you experience problems during installation,

consult your Kenwood dealer.

• When you purchase optional accessories, check

with your Kenwood dealer to make sure that they

work with your model and in your area.

• The characters conforming to ISO 8859-1 character

set can be displayed.

•

Applying spray cleaner directly to the unit may affect its

mechanical parts. Wiping the faceplate with a hard cloth

or using a volatile liquid such as thinner or alcohol may

scratch the surface or erases characters.

• The RDS or RBDS feature won’t work where the

service is not supported by any broadcasting

station.

Lens Fogging

When you turn on the car heater in cold weather,

dew or condensation may form on the lens in the

disc player of the unit. Called lens fogging, this

condensation on the lens may not allow discs to play.

In such a situation, remove the disc and wait for the

condensation to evaporate. If the unit still does not

operate normally after a while, consult your Kenwood

dealer.

DNX7120/DDX712/DDX7032

Notes

List of playable discs

Navigation units that can be connected to

this unit (DDX712/DDX7032 only)

Disc

types

DVD

Standard

Support

Remark

• KNA-G510*

• KNA-DV4100

• KNA-DV2100

‡

DVD Video

DVD Audio

DVD-R

• KNA-DV3100

* Update the navigation software to the latest

version. For how to update the software, refer to the

instruction manual of the navigation unit.

‡

MP3/WMA/AAC/JPEG/

MPEG Playback

Multi-border/Multisession/

(Playback depends on

authoring conditions)

Compatible with 8-cm (3

inch) discs

‡

DVD-RW

DVD+R

iPod that can be connected to this unit

You can control an iPod from this unit by connecting

an iPod (commercial product) with Dock connector

using an optional accessory iPod connection cable

(KCA-iP300V).

The following iPods can be controlled from this unit.

• iPod nano

• iPod nano (Second Generation)

• iPod nano (3rd Generation)

• Fifth Generation iPod (iPod with video)

• iPod classic

DVD+RW

‡

DVD-R DL (Dual layer)

DVD+R DL (Double layer)

DVD-RAM

Only video format

‡

Music CD

CD-TEXT/8-cm (3 inch)

discs supported.

MP3/WMA/AAC/JPEG

playback

Multisession supported

Packet write not supported.

‡

CD-ROM

CD-R

CD-RW

• iPod touch

Update iPod software to the latest version.

Supports audio only on iPod Touch.

‡

DTS-CD

Video CD (VCD)

Super video CD

Photo CD

CD-EXTRA

Only music CD session can

be played.

Sound quality of normal

CD music

By connecting your iPod to this unit with an optional

accessory iPod connection cable (KCA-iP300V), you

can supply power to your iPod as well as charge it

while playing music. However, the power of this unit

must be on.

HDCD

CCCD

Others

Dualdisc

Super audio CD

Only CD layer can be

played.

Bluetooth unit that can be connected to

this unit

• KCA-BT200

‡ : Playback is possible.

% : Playback is partly possible.

× : Playback is impossible.

About Satellite Radio tuner

This unit supports Satellite Radio tuners which are

released by SIRIUS and XM.

Optional accessories below are necessary for

connection.

SIRIUS tuner : Conversion cable CA-SR20

XM tuner : XM interface Box KCA-XM100

Use of "DualDisc"

When playing a "DualDisc" on this unit, the surface

of the disc that is not played may be scratched

while the disc is inserted or ejected. Since the music

CD surface does not conform to the CD standard,

playback may be impossible.

(A "DualDisc" is a disc with one surface containing

DVD standard signals and the other surface

containing music CD signals.)

Refer to the instruction manual of Satellite Radio

tuner.

About HD Radio

When you connect an HD Radio, Tuner features of

the unit are disabled and changed to HD Radio tuner

features.

With the HD Radio tuner, you can use the similar

functions of Tuner features. Refer to Tuner features for

how to use the functions.

English

Notes

About Audio files

iPod with KCA-iP300V

•

Playable Audio file

Acceptable discs, disc formats, file and folder names

and playing order are the same as those for audio

files. Refer to <About Audio files>.

AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)

⁄

•

If music of normal CD and other playback systems are

About Picture files

Acceptable picture files

JPEG

Extensions

jpg, jpeg

Acceptable media

CD-R/RW/ROM, DVD R/RW

Acceptable discs, disc formats, file and folder names

and playing order are the same as those for audio

files. Refer to <About Audio files>.

recorded in the same disc, only the playback system

recorded at the first setout is played.

Playable disc media

CD-R/RW/ROM, DVD R/RW

Playable disc file format

ISO 9660 Level 1/2, Joliet, Romeo, Long file name.

Playable USB device

USB mass storage class, iPod with KCA-iP300V

Playable USB device file system

FAT16, FAT32

•

Although the audio files are complied with the standards

listed above, the play maybe impossible depending on

the types or conditions of media or device.

About USB device

• If you start playback after connecting the iPod, the

music that has been played by the iPod is played

first.

In this case, "RESUMING" is displayed without

displaying a folder name, etc. Changing the browse

item will display a correct title, etc.

• When the iPod is connected to this unit,

"KENWOOD" or "✓" is displayed on the iPod to

indicate that you cannot operate the iPod.

• When the USB device is connected to this unit,

it can be charged up provided that this unit is

powered.

• Install the USB device in the place where it will not

prevent you from driving your vehicle properly.

• You cannot connect a USB device via a USB hub

and Multi Card Reader.

• Take backups of the audio files used with this unit.

The files can be erased depending on the operating

conditions of the USB device.

We shall have no compensation for any damage

arising out of erasure of the stored data.

• No USB device comes with this unit. You need to

purchase a commercially available USB device.

• When connecting the USB device, usage of the CA-

U1EX (option) is recommended.

Normal playback is not guaranteed when a cable

other than the USB compatible cable is used.

Connecting a cable whose total length is longer

than 5 m can result in abnormal playback.

•

Playing order of the Audio file

In the example of folder/file tree shown below, the

files are played in the order from ① to ⑩.

FFoollddeerr

AAuuddiioofﬁile

(ꢂ)

vꢀ

ꢁ

ꢃ

vꢆ

vꢇ

ꢅ

vꢄ

ꢈ

vꢉ

An online manual about audio files is put on the

site, www.kenwood.com/audiofile/. On this online

manual, detailed information and notes which are

not written in this manual are provided. Make sure

to read through the online manual as well.

⁄

•

In this manual, the word "USB device" is used for flash

memories and digital audio players which have USB

terminals.

•

The word "iPod" appearing in this manual indicates the

iPod connected with the KCA-iP300V (optional accessory).

About Video files

•

Acceptable video files

MPEG1, MPEG2

Extensions

mpg, mpeg, m1v, m2v

Acceptable media

CD-R/RW/ROM, DVD R/RW, VCD,

DNX7120/DDX712/DDX7032

Region codes in the world

The DVD players are given a region code according to the country or area it is marketed, as shown in the

following map.

DVD disc marks

Operation regulatory marks

With this DVD, some functions of this unit such as the

play function may be restricted depending on the

location where the DVD is playing. In this case, the

following marks will appear on the screen. For more

information, refer to the disc manual.

Symbol

Description

Indicates a region number. The discs with this mark can

be played with any DVD player.

ALL

Indicates the number of audio languages recorded. Up

to 8 languages can be recorded in a movie. You can

select a favorite language.

Prohibition Mark

禁止マーク

Indicates the number of subtitled languages recorded.

Up to 32 languages can be recorded.

Discs with limited period of use

Do not leave discs with a limited period of use in this

unit. If you load an already expired disc, you may not

be able to remove it from this unit.

If a DVD disc has scenes shot from multiple angles, you

can select a favorite angle.

Indicates the type of screen for the image. The left mark

indicates that a wide image picture (16:9) is displayed

on a standard TV set screen (4:3) with a black band at

both the top and bottom of the screen (letter box).

16:9 LB

English

Basic Operations

Turns power ON/OFF

Switches to the Navigation system

Press the button to turn on the power.

When the button is pressed and held down for

1 second or more, the power is turned off.

Press the button to switch the display to the

navigation system screen.

Attenuates the volume

Press it to attenuate the volume.

Press it again to cancel muting.

Adjusts the volume

Playing a USB device

When connecting a USB device, playback starts automatically.

You must update the database if you are using a USB device that is different from the one you used

before or if you have replaced the audio files in the USB device. For information on how to update the

database, refer to <Function while displaying the Control Screen> in USB Device Control (page 36).

⁄

•

If the USB source is selected when a USB device is not connected, "No Device" is

displayed.

•

When the playback is stopped and then restarted, the playback will start from

the point where it was stopped at the last time. Even if the USB is removed and

connected again, the playback will start from the last stopped point unless the

contents in the USB device is changed.

•

Make sure that the USB device is connected firmly.

Removing the USB device

Press

on the USB control screen to enter the USB suspend mode, and then remove the USB

device. Refer to <USB Device Control> (page 36).

•

Removing the USB device before entering the USB suspend mode may result in damaging the data in the USB device.

DNX7120/DDX712/DDX7032

Selecting a source

Press it to display the source select screen. Touch the source button to select the source.

Full Source Select screen

1 Scrolls the source display.

⁄

•

The displayed source depends on the type of device

connected. In addition, you cannot press the button of

currently unavailable source.

The following buttons are always displayed on the

source select screen and source control screen.

2 Clock display

3 Displays the Source Select screen.

The display switches between Favorite Source Select

screen and Full Source Select screen by touching the

button.

4 Displays Source Control screen.

5 Displays the Audio Control Menu screen. (page 86)

6 Displays the SETUP Menu screen. (page 62)

7 Displays the external device control screen. See

<External Device Power Supply Control> (page 47).

8 Changes the screen skin each time it is pressed.

9 Displays the Hands Free screen. (page 51)

p Adjust the volume.

Favorite Source Select screen

q Press for at least 2 seconds to erase the buttons. Touch

the screen to redisplay the buttons.

⁄

•

If a Bluetooth Unit is not connected, [TEL] will not appear.

w Displays the full source screen.

⁄

•

For how to register the frequently used source buttons to

Favorite Source Select screen, see <Direct Source Button

Setup> (page 70).

Playing a disc

When you load a disc into disc loading slot, the disc starts playing.

If a menu appears, when playing a video disc, select the desired item.

⁄

• See <List of playable discs> (page 7) for a list of supported discs and formats.

Removing a disc

Press

(Eject) button.

English

Basic Operations

Switches to the Hands Free control

Switches to the rear view

Press it for more than 1 second to the Hands

Free control screen.

Press it for more than 1 second to switch to

rear view.

Press it again for more than 1 second to

resume the normal display.

Press it again for more than 1 second to

resume the normal display.

(with the optional accessory Bluetooth unit

connected only)

⁄

• Functions of the [NAV] button can be changed to

Display Off function. See <System Setup> (page 66)

for the function setting of the [NAV] button.

Sets the Loudness

Press it for more than 1 second to turn the

Loudness function on or off.

If turned on, high and low tones are enhanced

during low volume.

DNX7120/DDX712/DDX7032

Switching the function screen

The function control screen switches in the following order each time you press the button.

Navigation screen

Picture or Video playback

screen

[FNC] button

Easy Control buttons

appear.

Easy Control buttons

appear.

Navigation screen

Picture or Video playback screen

Mode:Full AV–OUT:AV–IN

DVD VIDEO

SCRN

ꢀ

DVD MEDIA

0:00:05

DVD VIDEO

Title

C ha p

0:00:05

PICTURE

Easy Control button

⁄

• For the functions of Easy Control buttons, see <Control of other sources while displaying the navigation screen> (page

14).

English

Navigation Control

Sets and controls the navigation system function.

Control of Other Sources While Displaying

the Navigation Screen

Using the Navigation System

Displays the navigation system screen and makes

the navigation function available.

Selected source can be controlled while

displaying navigation screen.

Displaying the navigation screen

Display the easy control buttons

When "DVD" is selected:

SCRN

ꢀ

DVD VIDEO

Title

C ha p

0:00:05

Setting the navigation system function

Touch the navigation system button displayed

on the screen. See the included NAVIGATION

SYSTEM's INSTRUCTION MANUAL for

1 ∞: changes between [SCRN], [TEL], and [EXT

SW] button each time this is pressed.

SCRN: Displays the Screen Control screen.

See <Screen Control> (page 50).

TEL: Displays the Hands Free screen. (page

51)

EXT SW: Displays the external device control

screen. See <External Device Power

Supply Control> (page 47).

2 Adjust the volume.

information on using the navigation system.

⁄

•

You can set the navigation system function when

nothing else is displayed on the screen. If anything else,

such as Easy control panel is displayed, erase it first.

For DDX712/DDX7032, an optional navigation system

needs to be connected. See <Navigation unit that can

be connected to this unit> (page 7) for connectable

navigation units.

•

3 During DVD play :

Selects a chapter.

During VCD play :

Selects a scene (when PBC is On) or a track

(when PBC is Off).

During CD play :

Selects music.

During Audio file, Video file, or Picture file

play :

Selects a file.

4 Stops playing.

When pressed twice, the disc is played from

its beginning when you play it in the next

DNX7120/DDX712/DDX7032

time. (DVD play only)

5 Plays or pauses.

6 When touched this area, the source control

screen appears.

When "Bluetooth" is selected:

a Selects a file.

s Plays.

d Pauses.

When "USB" or "iPod" is selected:

iPod

0:00:05

f When touched this area, the source control

screen appears.

7 During iPod play :

Searches Music or Video.

During USB play :

Selects a file.

⁄

•

The Easy Control buttons are hidden when you touch the

central part of the screen.

8 Plays or pauses.

9 When touched this area, the source control

screen appears.

When "TUNER" is selected:

F M

TUNER

FM1

A M

98.1 MHz

p Tunes in a station.

q Switches the band (to AM or FM 1/2/3).

w When touched this area, the source control

screen appears.

When "SIRIUS" or "XM" is selected:

Band

SEEK

SIRIUS

100 ch

SEEK1

e Tunes in a station.

r Switches the band.

Sirius : SR1/ SR2/ SR3/ SR4

XM : XM1/ XM2/ XM3/ XM4

t Switches the Seek mode.

SEEK 1 : Tunes channels one after the other.

SEEK 2 : Selects channels in memory one

after the other.

y When touched this area, the source control

screen appears.

When "TV" is selected:

u Selects a channel.

Use the <Seek Mode> (page 40) to change

the channel tuning sequence.

i Switches to TV1 or TV2.

o Switches the Seek mode.

; When touched this area, the source control

screen appears.

English

Watching DVD/VCD

You can play DVD/VCD using various functions.

•

For the basic method of how to watch DVD/VCD, refer to <Basic Operations> (page 10).

Set the remote controller mode switch to "DVD" mode before starting operation, refer to <Remote Controller mode switch>

(page 90).

6 DVD Disc Menu Control Buttons Area

Displays the Disc Menu Control buttons

(page 18).

Functions During the Playback Screen

Basic functions are available even when the

playback screen is displayed.

The Highlight Control screen appears

when pressed while the DVD Top menu is

displayed.

Display the playback screen

7 Information Display Button Area

VCD playback screen

Mode:Full

DVD VCD

AV–OUT:AV–IN

DVD VCD

Scene

0:05

PBC

VER2

8 Scene/Track Number Display

9 Play time Display

p Forward Scene/Track Search Area

Selects the next scene (when PBC is On) or

track (when PBC is Off).

q Backward Scene/Track Search Area

Selects the previous scene (when PBC is On)

or track (when PBC is Off).

w Zoom Control Button Area

Displays the Zoom Control buttons (page

20).

e Information Display Button Area

DVD playback screen

Mode:Full

AV–OUT:AV–IN

DVD VIDEO

⁄

•

The information display is cleared automatically after

approximately 5 seconds. Also, the information can be

displayed automatically when it is updated.

DVD VIDEO

Title

C ha p

0:00:05

1 Title Number Display

2 Chapter Number Display

3 Play Time Display

4 Forward Chapter Search Area

Selects the next chapter.

5 Backward Chapter Search Area

Selects the previous chapter.

DNX7120/DDX712/DDX7032

Functions When Displaying the Easy

Control Panel

Functions While Displaying the Control

Screen

Displays the basic operation buttons on the

screen.

Switches to the source control screen to use

various playback functions.

While the source is playing, press the [FNC]

button

While the source is playing, press the [FNC]

button

Mode:Full

AV–OUT:AV–IN

DVD VIDEO

Mode:Full

AV–OUT:AV–IN

DVD VIDEO

SCRN

ꢀ

DVD VIDEO

Title

C ha p

0:00:05

DVD VIDEO

Title

C ha p

0:00:05

1 Chapter Search (during DVD play)

Searches for a chapter.

Scene/Track Search (during VCD play)

Selects a scene (when PBC is On) or a track

(when PBC is Off).

When playing a DVD

2 Stops playing.

When pressed twice, the disc is played from

its beginning when you play it in the next

time.

3 Plays or pauses.

4 Switches to the playback screen.

⁄

•

When the navigation screen is displayed, press the [NAV]

button to switch to the source playback screen.

The Easy Control Panel is hidden when you touch a

central part of the monitor.

When playing a VCD

•

1 Switches to the playback screen.

2 Title Number Display (during DVD play)

3 Chapter/Scene/Track Number Display

4 Play Mode Display

5 Play Time Display

Next page 3

English

Watching DVD/VCD

6 Volume Label Display

When is appeared, the text display is

DVD Disc Menu

Selects an option from the DVD Disc Menu.

scrolled by pressing it.

7 Fast Forwards or Fast Backwards.

8 Stops playing.

Display the Disc Menu Control screen

Mode:Full

AV–OUT:AV–IN

DVD VIDEO

When pressed twice, the disc is played from

its beginning when you play it in the next

time.

9 Selects a chapter, a scene or a track.

When the DVD-VIDEO/VCD is paused, touch

this button to start single-frame stepping.

p Plays or pauses.

DVD VIDEO

Title

C ha p

0:00:05

q Ejects the disc from the built-in disc player.

w Slow Forwards or Backwards. (during DVD

play)

e Switches the button display.

r Switches the Repeat Play operations in the

following sequence.

Top

e n u C t r l

Return

DVD: Title Repeat, Chapter Repeat, Repeat

Off

VCD: Track Repeat, Repeat Off (Available

when the PBC is off)

E n t e r

C a n c e

E x

Highlight

t Displays the Hands Free screen. (page 51)

y Switches the play time display in the

following sequence.

DVD: Chapter, Title, remaining titles

VCD: Track, disc, remaining discs (Effective

only when the PBC function is off)

u Function Indicator

1 Calls the Menu.

2 Returns to the Disc Menu screen.

3 Selects a menu option.

4 Enters your menu selection.

5 Returns to the previous menu screen.

6 Displays the Top Menu.

7 Highlight Control.

8 Clears the Disc Menu Control.

i Appears when a disc is inserted.

o Sound indicator

; Turns the PBC function of VCD On or Off.

(only when VCD Ver 2.0 is in use)

a Appears when PBC is On.

s VCD version indicator

d Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

DNX7120/DDX712/DDX7032

Highlight Control

(during program playback only)

q Switches the subtitle language.

(during program playback only)

w Switches the voice language.

(during program playback only)

e Displays the Zoom Control screen.

r Clears the Disc Menu Control.

You can select a chapter and title for the DVD

Menu screen. When you touch the screen, you

can select the DVD menu.

Top

e n u C t r l

Return

Zoom Control

Audio

1 / 2

e n u C t r l

S U B

3 / 3

E n t e r

C a n c e

E x

Highlight

Z o om

Angle

E x i t

1 / 1

H i g h l i gh t On

Z o omC t r l

⁄

•

To cancel Highlight Control, press [FNC] button.

The operation ends automatically if you do not operate

within 10 seconds.

Z o om

x 2

C a n c e

E x

t Changes the zoom ratio at 4 levels (2 times,

3 times, 4 times, or off) each time you

touch.

y Scrolls the screen in the direction you

touch.

Select Disc Menu options

Disc Menu

Top

e n u C t r l

Return

u Returns to the Disc Menu screen.

i Clears the Disc Menu Control.

E n t e r

C a n c e

E x i t

Highlight

Audio

1 / 2

e n u C t r l

S U B

3 / 3

E x

Z o om

Angle

i t

1 / 1

9 Calls the Menu Control.

p Switches the picture angle.

English

Watching DVD/VCD

VCD Zoom Control

Displays an enlarged VCD screen.

Display the Zoom Control screen

Mode:Full

DVD VCD

AV–OUT:AV–IN

DVD VCD

Scene

0:05

PBC

VER2

Z o omC t r l

Z o om

x 2

E x

1 Changes the zoom ratio at 2 levels (2 times

or off) each time you touch.

2 Scrolls the screen in the direction you

touch.

3 Clears the Zoom Control button.

DNX7120/DDX712/DDX7032

Music Disc & Audio File Listening

You can recall various control screens during CD/Audio file playback.

•

For the basic method of how to play a music disc/audio file, refer to <Basic Operations> (page 10).

Refer to <List of playable discs> (page 7) for playable discs.

Refer to <About Audio file> (page 8) for playable files.

Functions While Displaying the Control

Screen

Selects the Disc Name (See <Set Disc

Name>, page 23), Disc Text or Track Text.

When

is appeared, the text display is

Switches to the source control screen to use

various playback functions.

scrolled by pressing it.

5 Fast Forwards or Fast Backwards.

6 Stops playing the built-in disc player. When

pressed twice, the disc is played from its

beginning when you play it in the next

time.

7 Selects a track.

8 Plays or pauses.

9 Ejects the disc from the built-in disc player.

p Starts or stops Scan Play (that plays the

beginning of each music one after the

other).

q Repeats to play (the present track).

w Starts or stops Random Play (to play music

in random order).

e Switches the number of lines displayed in

the Information Display.

r Displays the Hands Free screen. (page 51)

t Switches the play time display between

Track, Disc, and Disc Remaining Time.

y Function Indicator

u Appears when a disc is inserted.

i Sets a name to the disc being played. See

<Set Disc Name> (page 23).

o Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

During CD playback

1 Track (Music) Number Display

2 Play Mode Display

3 Play Time Display

4 Music information display

Next page 3

English

Music Disc & Audio File Listening

During Audio file playback

; Appears when a disc is inserted.

a Repeats to play the music or data of the

present folder.

s You can search for folders and Audio files

through a hierarchy. See <Folder Select>

(page 23).

d Displays music information (such as Tag

and content property) of Audio file being

played.

f Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

1 Switches to the playback screen. If there is

no playback screen, wallpaper is displalyed.

2 Folder and File Number Display

3 Play Mode Display

4 Play Time Display

5 Music information display

Selects Folder Name, File Name, Title, Artist

Name, or Album Name.

When

is appeared, the text display is

scrolled by pressing it.

6 Fast Forwards or Fast Backwards.

(Disabled when a JPEG is being played.)

7 Stops playing.

When pressed twice, the disc is played back

from its beginning in the next time.

8 Selects a file.

9 Plays or pauses.

p Ejects a disc.

q Selects a folder.

w Switches the button display.

e Starts or stops Scan Play (that plays the

beginning of each music or data one after

the other).

r Repeats to play (the preset files or data).

t Starts or stops Random Play (to play files of

the present folder in random order).

y Switches the number of lines displayed in

the Information Display.

u Displays the Hands Free screen. (page 51)

i Function Indicator

o MUSIC, MOVIE or PICTURE indicator

DNX7120/DDX712/DDX7032

Set Disc Name

Folder Select (Function of Audio File)

Assigns a name to a CD.

Searches folders and Audio files stored in media

and devices according to hierarchy.

Play a CD you wish to name

Start Name set

Start Folder Select

Selects a song

Enter the name

See <Character Entry> (page 49) for

information on how to enter a name.

End Name set

1 Scrolls the list.

2 Lists folders and Audio files

Folder opens when touched, and the Audio

file is played.

When

is appeared, the text display is

scrolled by pressing it.

3 Moves to the top hierarchy level.

4 Moves up a hierarchy level.

5 Opens the selected folder.

6 Returns to the original screen.

English

Video File/Picture Watching

You can recall various control screens during playback of video file (MPEG 1 and MPEG 2 file) and picture file

(JPEG file).

Function During Playback Screen

⁄

•

The information display is cleared automatically after

approximately 5 seconds. Also, the information can be

displayed automatically when it is updated.

Basic functions are available even when the

playback screen is displayed.

Display the playback screen

Functions When Displaying the Easy

Control Panel

Displays the basic operation buttons on the

screen.

While the source is playing, press the [FNC]

button

Mode:Full

AV–OUT:AV–IN

DVD MEDIA

SCRN

ꢀ

DVD MEDIA

0:00:05

PICTURE

Mode:Full

AV–OUT:AV–IN

DVD MEDIA

1 Selects a file.

2 Stops playing.

3 Plays or pauses.

⁄

•

When the navigation screen is displayed, press the [NAV]

button to switch to the source playback screen.

The Easy Control Panel is hidden when you touch a

central part of the monitor.

DVD MEDIA

0:00:05

•

1 Folder/File Number Display

2 Play Time Display

3 Forward File Search Area

Selects the next file.

4 Backward File Search Area

Selects the previous file.

5 JPEG: Picture Control Button Area (page 26)

MPEG: Not effective

6 Information Display Button Area

DNX7120/DDX712/DDX7032

Functions While Displaying the Control

Screen

When

scrolled by pressing it.

6 Fast Forwards or Fast Backwards.

(Disabled when a JPEG is being played.)

7 Stops playing.

is appeared, the text display is

Switches to the source control screen to use

various playback functions.

When pressed twice, the disc is played back

from its beginning in the next time.

8 Selects a file.

While the source is playing, press the [FNC]

button

9 Plays or pauses.

p Ejects a disc.

q Selects a folder.

w Switches the button display.

e Starts or stops Scan Play (that plays the

beginning of each song or data one after

the other).

Mode:Full

AV–OUT:AV–IN

DVD MEDIA

r Repeats to play (the preset files or data).

t Starts or stops Random Play (to play files of

the present folder in random order).

y Switches the number of lines displayed in

the Information Display.

SCRN

ꢀ

DVD MEDIA

0:00:05

PICTURE

u Displays the Hands Free screen. (page 51)

i Function Indicator

o PICTURE or MUSIC indicator

; Appears when a disc is inserted.

a Repeats to play the file of the present folder.

s You can search for folders and files through

a hierarchy. See <Folder Select> (page 26).

d Displays information of file being played.

f Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

1 Switches to the playback screen.

2 Folder and File Number Display

3 Play Mode Display

4 Play Time Display

5 Video/Picture information display

Selects Folder Name, File Name, Title, Artist

Name, or Album Name.

English

Video File/Picture File Watching

Picture Control

Folder Select

Adjusting the video display.

Searches folders and Video files/Pictures stored in

media and devices according to hierarchy.

Start Picture Control

Start Folder Select

Mode:Full

AV–OUT:AV–IN

DVD MEDIA

0:00:05

Adjust the video display

Selects a file

Picture Ctrl

Exit

1 Reverses the picture horizontally.

2 Rotates counter clockwise.

3 Rotates clockwise.

1 Lists folders and Video files/Picture files.

Folder opens when touched, and the Video/

Picture file is played.

4 Ends Picture Control.

When

is appeared, the text display is

scrolled by pressing it.

2 Scrolls the list.

3 Moves to the top hierarchy level.

4 Moves up a hierarchy level.

5 Opens the selected folder.

6 Returns to the original screen.

DNX7120/DDX712/DDX7032

Radio Listening

Various control screens appear in the Tuner Source mode.

•

For the basic method of receiver button operations, refer to <Basic Operations> (page 10).

Set the remote controller mode switch to "AUD" mode before starting operation, refer to <Remote Controller mode switch>

(page 90).

Functions While Displaying the Control

Screen

1/2, or Radio Text.

5 Turns the Traffic Information function On or

Off.

See <Traffic Information>, (page 31).

6 Switches to the FM1/2/3 band.

7 Switches to the AM band.

Switches to the source control screen to use

various functions.

8 Tunes in a station.

Use the <Seek Mode> (page 28) to change

the frequency switching.

9 Switches the button display.

p Turns the CRSC function On or Off. (Only

when receiving the FM broadcast)

q Selects the Auto Memory mode.

(Refer to page 28 for the <Auto Memory>)

w Switches the Seek mode.

(Refer to page 28 for the <Seek Mode>)

e Switches the number of lines displayed in

the Information Display.

r Displays the Hands Free screen. (page 51)

t When

buttons appear, you

can recall the stations on memory.

For memory of broadcasting stations, refer

to <Auto Memory> (page 28) or <Manual

Memory> (page 29).

y Sets a name to the station. See <Set Station

Name> (page 30).

u Searches station by program type. See

<Search for Program Type> (page 31).

i Lists and selects memorized station. See

<Preset Select> (page 29).

o Displays Radio Text screen. See <Radio

Text> (page 30).

; Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

1 Band display

2 Preset number

3 Frequency display

4 Radio station information display.

Selects the Program Service Name, Title &

Artist name, Station Name, Category Name

English

Radio Listening

Seek Mode

Auto Memory

Sets a station selection.

Stores stations with good reception in memory

automatically.

Select a band you wish to store in memory

The mode is switched in following order each

time you touch the button.

Display

"AUTO1"

Setting

Select the Auto Memory mode

Tunes in a station with good reception

automatically.

"AUTO2"

"MANU"

Tunes in stations in memory one after another.

Switches to the next frequency manually.

Start Auto Memory

Touch

Auto Memory terminates when 6 stations are

stored or when all stations are tuned in.

⁄

•

The operation ends automatically if you do not operate

within 10 seconds.

DNX7120/DDX712/DDX7032

: Press for # seconds.

Manual Memory

Preset Select

Stores the current receiving station in memory.

Lists and selects memorized station.

Select a station you wish to store in

memory

1 Start Preset Select

Selects a station

Store in memory

1 Scrolls the list.

2 Memorized stations are displayed. Touch to

tune in.

Continue to touch until the memory number

appears.

3 Switches the list display name to Station

name or Program Service Name.

4 Returns to the original screen.

English

Radio Listening

Radio Text

Set Station Name

You can display the radio text. (Only when

receiving the FM broadcast)

Assigns a name to a station.

Tune in to the station to name

Start Name set

Select a station

Display the radio text

Enter the name

See <Character Entry> (page 49) for

information on how to enter a name.

End Name set

1 Selects the Program Service Name, Title &

Artist name, Station Name, Radio Text Plus,

or Radio Text for text display.

When

is appeared, the text display is

scrolled by pressing it.

2 Scrolls the text display.

3 Returns to the original screen.

DNX7120/DDX712/DDX7032

: Press for # seconds.

Traffic Information

Search for Program Type

When a traffic bulletin starts, any source is

switched to the traffic information and it is

displayed automatically.

A program is tuned when you set its program

type. (Only when receiving the FM broadcast)

Enter Program Type mode

Set the Traffice information mode

When the traffic bulletin starts...

Select a Program Type

The Traffic Information screen appears

automatically.

Traffic Information screen

1 Program Type is displayed. Touch to select a

Program Type.

2 Scrolls the Program Type list.

⁄

Search a station of the selected Program

Type

•

It is necessary to have Traffic Information function set to

On in order to have the Traffic Information screen appear

automatically.

•

During reception of traffic information the adjusted

volume is automatically remembered, and the next time

it switches to traffic information it's automatically the

remembered volume.

3 Searches for the program type.

It is displayed when the Program type is

selected.

4 Continue to touch more than 2 seconds,

the currently receiving station is registered

to have the selected program type.

English

iPod Control

You can control and listen to songs in your iPod by connecting an iPod to this unit with KCA-iP300V

(optional accessory). You can also display video contents on this unit when connecting an iPod with video.

Functions when Displaying the Easy

Control Panel

Connecting an iPod

Connect an iPod to this unit.

Displays the basic operation buttons on the

screen.

While the source is playing, press the [FNC]

button

Mode:Full

AV–OUT:AV–IN

iPod

Mode:Full

AV–OUT:AV–IN

iPod

SCRN

ꢀ

iPod

0:00:05

iPod

0:00:05

1 Forward music/video search area

1 Music/Video Search.

2 Plays or pauses.

Selects the next music/video.

2 Backward music/video search area

Selects the previous music/video.

3 Information display button area

The information is displayed for 5 seconds.

⁄

•

When the navigation screen is displayed, press the [NAV]

button to switch to the source playback screen.

The Easy Control Panel is hidden when you touch a

central part of the monitor.

•

⁄

•

Remove all accessories such as headphone before

connecting an iPod. You may not be able to control the

iPod if you connect it with accessories attached.

When you connect an iPod to this unit, playback starts

from the song you were playing on the iPod itself

(Resume Function).

•

If the played song is not a video content, "No iPod Video

Signal" is displayed on the video screen.

While connecting an iPod, "KENWOOD" appears on the

iPod and the iPod's control is disabled.

DNX7120/DDX712/DDX7032

Functions while Displaying the Control

Screen

Switches to the source control screen to use

various playback functions.

When Video or picture is playing, press the

[FNC] button.

1 Image picture

Switches to the playback screen. If there is

no playback screen, wallpaper is displalyed.

2 Total number of music in the iPod and the

music number display

3 Play Mode Display

Mode:Full

AV–OUT:AV–IN

iPod

4 Play Time Display

5 Music/Video Information Display

Selects the Title, Artist Name, Album Name

or iPod Name.

SCRN

ꢀ

When

is appeared, the text display is

scrolled by pressing it.

iPod

0:00:05

6 Fast Forwards or Fast Backwards.

7 Selects Music/Video.

8 Plays or pauses.

9 Switches the button display.

p Starts or stops Scan Play (that plays the

beginning of each music or video one after

the other).

q Repeats to play (the preset files or data).

w Starts or stops Random play.*

e Displays the Hands Free screen. (page 51)

r MUSIC or VIDEO indicator

t Starts or stops Album Random Play (plays

randomly from current album).*

y Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

u Displays the list of music category. See

<iPod List> (page 34).

i Displays the list of video category. See

<iPod List> (page 34).

o Displays the previous music/video list

screen. See <iPod List> (page 34).

; Displays information screen of music/video

being played.

⁄

* Disabled when VIDEO is being played.

English

iPod Control

iPod List

Lists and searches music/video contained in the

iPod.

Display the iPod List

Select music/video

1 Switches list page.

2 Categories and music are listed.

Touch a category name to move its lower

level. If music title is displayed, the music is

played by touching it.

When

is appeared, the text display is

scrolled by pressing it.

3 All the music in its category is played.

4 Returns to previous category.

5 Moves to the top category.

6 Displays the currently playing category.

DNX7120/DDX712/DDX7032

English

USB Device Control

You can control and listen to songs in your USB device by simply connecting it to the USB connector of this

unit.

•

For the connection of a USB device, refer to <Basic Operations> (page 10).

Functions while displaying the Control

Screen

5 Removes the USB device.

When "No Device" is shown, the USB device

can be removed safely.

If you wish to play it again while the USB

device is connected, press it again.

6 Selects a folder. (Only in Folder Select

Mode)*

Switches to the source control screen to use

various playback functions.

7 Selects a file.

8 Plays or pauses.

9 Switches the button display.

p Starts or stops Scan Play (that plays the

beginning of each music one after the

other).

q Repeats to play (the present music).

w Starts or stops Random Play (to play music

in random order).

e Displays the Hands Free screen. (page 51)

r Repeats to play the music or data of the

present folder. (Only in Folder Select Mode)

t Updates the audio file database in the USB

device.

y Displays the folder list. Refer to <Folder

Select> (page 37).

u Displays the list of category. Refer to <USB

List> (page 37).

i Displays information screen of music being

played.

o Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

⁄

* Disabled during play list mode.

1 Track (Music) Number Display

2 Play Mode Display

3 Play Time Display

4 Music information display

Selects the Folder Name, File Name, TItle,

Artist Name, or Album Name.

When

is appeared, the text display is

scrolled by pressing it.

DNX7120/DDX712/DDX7032

USB List

Folder Select

Lists and searches music contained in the USB

device.

Searches folders and Audio files stored in the USB

device according to hierarchy.

Display the Category List

1 Start Folder Select

Select a category

2 Select music

When

is appeared, the text display is

1 Lists folders and Audio files

scrolled by pressing it.

1 Displays the currently playing category.

2 Returns to the original screen.

Folder opens when touched, and the Audio

file is played.

2 Scrolls the list.

3 Moves to the top hierarchy level.

4 Moves up a hierarchy level.

5 Displays the currently playing file.

Select music

3 Switches to the lower level of the category.

When is appeared, the text display is

scrolled by pressing it.

4 Scrolls the list.

5 Lists all the music in the selected category.

6 Moves to the upper level of the category.

7 Moves to the top category.

8 Displays the currently playing category.

(Only in Category Mode)

9 Returns to the original screen.

English

TV Watching

Various control screens appear in the TV source mode. You can only operate TV with the optional accessory

TV Tuner connected.

Functions When Displaying the Easy

Control Panel

Function During TV Screen

Basic functions are available even when the TV

screen is displayed.

Displays the basic operation buttons on the

screen.

Display the TV screen

While the source is playing, press the [FNC]

button

Mode:Full

AV–OUT:AV–IN

SCRN

ꢀ

Mode:Full

AV–OUT:AV–IN

BAND SEEK

Preset 1

2ch

TV1

1 Selects a channel.

Use the <Seek Mode> (page 40) to change

the channel tuning sequence.

TV1

Group 1

Preset 1

2ch

⁄

AUTO1

•

When the navigation screen is displayed, press the [NAV]

button to switch to the source playback screen.

The Easy Control Panel is hidden when you touch a

central part of the monitor.

1 TV Band Number Display

2 Memory Number Display

3 Channel Number Display

4 Channel Up Area

•

Increases the channel.

5 Channel Down Area

Decreases the channel.

6 Band Switch Area

Switches to TV1 or TV2.

7 Information Display Button Area

⁄

•

The information display is cleared automatically after

approximately 5 seconds. Also, the information can be

displayed automatically when it is updated.

DNX7120/DDX712/DDX7032

Functions While Displaying the Control

Screen

7 Switches to TV1 or TV2.

8 Switches the button display.

9 Selects the Auto Memory mode.

See <Auto Memory> (page 41).

p Switches the Seek mode.

Switches to source control screen to use various

functions.

See <Seek Mode> (page 40).

While the source is playing, press the [FNC]

button

q Displays the Hands Free screen. (page 51)

w Indicates current Seek mode.

e When

buttons, you can

recall channels on memory.

For memory of broadcasting stations, see

<Auto Memory> (page 41) or <Manual

Memory> (page 41).

r Sets a name to the tuned station. (page 42)

t Lists and selects memorized station.

y Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

Mode:Full

AV–OUT:AV–IN

SCRN

ꢀ

BAND SEEK

Preset 1

2ch

TV1

1 Switches to the TV screen.

2 Band display

3 Memory Number Display

4 Channel display

5 Channel information display

6 Select a channel.

Use the <Seek Mode> (page 40) to change

the channel tuning sequence.

English

TV Watching

Seek Mode

Auto Memory

Sets a station selection.

Stores stations with good reception in memory

automatically.

Select a band you wish to store in memory

The mode is switched in following order each

time you touch the button.

Display

"AUTO1"

Setting

Select the Auto Memory mode

Tunes in a station with good reception

automatically.

"AUTO2"

"MANU"

Tunes in stations in memory one after another.

Switches to the next frequency manually.

Start Auto Memory

Auto Memory terminates when 6 stations are

stored or when all stations are tuned in.

⁄

•

The operation ends automatically if you do not operate

within 10 seconds.

DNX7120/DDX712/DDX7032

: Press for # seconds.

Manual Memory

Stores the current receiving channel in memory.

Select a station you wish to store in

memory

Store in memory

Continue to touch until the memory number

appears.

English

TV Watching

Preset Select

Set Station Name

Lists and selects memorized station.

Assigns a name to a station.

Start Preset Select

Select a station you wish to name

Start Name set

Selects a station

Enter the name

See <Character Entry> (page 49) for

information on how to enter a name.

End Name set

1 Memorized stations are displayed. Touch to

tune in.

DNX7120/DDX712/DDX7032

SIRIUS/XM Control (North American sales area only)

Various control screens appear in the Satellite radio source mode. (with the optional accessory Satellite

radio connected only. To connect the Sirius tuner, a conversion cable CA-SR20V (optional accessory) is

necessary and to connect the XM tuner, an XM interface Box KCA-XM100V (optional accessory) is necessary.)

•

This document uses the SIRIUS display as an example.

Functions While Displaying the Control

Screen

XM : Changes the display from Channel

Name, Song Title Name, to Category

Name.

Displays the ID number when Channel 0 is

selected.

Switches to control screen to use various

functions.

Sirius : Displays the SIRIUS ID.

XM : Displays the RADIO ID.

5 Tunes in a station.

6 Switches the band.

7 Switches the button display.

8 Starts or stops Channel Scan (that tunes

channels one after the other).

9 Switches the Seek mode.

SEEK 1: Tunes channels one after the other.

SEEK 2: Selects channels in memory one

after the other.

p Switches the number of lines displayed in

the Information Display.

q Displays the Hands Free screen. (page 51)

w Indicates current Seek mode

e When

buttons appear, you

can recall the channel on memory. For

memory of channel stations, see <Channel

Memory> (page 44) .

r You can tune in by entering the desired

channel number. See <Direct Channel

Search> (page 45)

t You can tune in by specifying the desired

category. See <Channel Search> (page 44)

y Displays the program information screen.

u Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

1 Band display

2 Preset number

3 Channel display

4 Displays information concerning music

being played.

Sirius : Changes the display from Channel

Name, Song Title Name, Artist Name,

Composer Name, to Category Name.

English

SIRIUS/XM Control (North American sales area only)

Channel Search

Channel Memory

Specifying the desired category and selecting a

channel.

Stores the current receiving channel in memory.

Select a channel you wish to store in

memory

Start Channel Search

Store in memory

Select a category

1 Selects a category.

Continue to touch until the memory number

appears.

Displays the channel screen.

2 Scrolls the category.

3 Displays all channels of all categories.

Select a channel

4 Selects a channel.

Tunes in the selected channel.

5 Scrolls the channel list.

6 Display the category list.

7 Switches the sequence of the list.

Changes the display from Channel Name,

Category Name, Song Title, Artist Name, to

Composer Name. (SIRIUS only)

DNX7120/DDX712/DDX7032

: Press for # seconds.

Direct Channel Search

Tuning in by entering the desired channel

number.

Start Direct Channel Search

Enter the channel number

1 Enters the channel number.

2 Cancels the direct channel search.

3 Clears the channel number.

Tune in the channel

English

Bluetooth Audio Control

When KCA-BT200 (optional accessory) is connected, you can listen to audio files stored in Bluetooth audio

player and cell-phone.

•

You need to register your audio player to your Bluetooth Unit beforehand. Make sure to read the instruction manual of the

Bluetooth Unit as well.

Functions While Displaying the Control

Screen

Switches to control screen to use various

functions.

1 Plays.

2 Pauses.

3 Stops playing.

4 Selects a file.

5 Displays the Hands Free screen. (page 51)

6 Displays the external device control

screen. See <External Device Power Supply

Control> (page 47).

⁄

•

If the Bluetooth Audio player does not support AVRCP

profile, buttons 1 to 4 are not displayed. Operate from

the Audio player.

DNX7120/DDX712/DDX7032

External Device Power Supply Control

Controlling the external device power supply.

External Device Power Supply Control

Controlling the external device power supply.

Displays the EXT SW Control screen

[EXT SW] appears when the control screen of

each source or Easy control panel is displayed.

Controls the external device power supply

1 You can turn on or off the external device

power supply.

2 Returns to the original screen.

⁄

•

You must connect a commercially available relay unit in

order to use this function.

Connect the external device to be controlled to that

relay unit.

•

Refer to <EXT SW Setup> (page 85) for information on

setting the power on or off specification.

English

Muting Audio Volume upon Reception of Phone call

When the telephone is called, the system is paused automatically.

Muting Audio Volume upon Reception of

Phone Call

When the telephone is called...

The Phone Call ("CALL") screen appears, and

system is paused.

Phone Call ("CALL") screen

When the call ends...

Hang up the phone.

The system resumes playing automatically.

⁄

•

To use the TEL Mute feature, you need to hook up

the MUTE wire to your telephone using a commercial

telephone accessory. Refer to <INSTALLATION MANUAL>.

DNX7120/DDX712/DDX7032

Character Entry

When you select the Set Station Name mode or others, the following screen appears for character entry.

How To Use the Character Entry Screen

Character Entry screen

1 Shifts the cursor.

2 Enters characters.

3 Scrolls up or down the character button

display.

4 Sets the key layout of the character buttons.

abc : Alphabetical key layout.

qwe : Qwerty key layout.

5 Enters a space.

If you erase a character, locate the cursor on

it and touch this button.

6 Clears the character.

7 Exits the Character Entry mode and returns

to the previous screen.

⁄

•

You can enter characters only after you have applied the

parking brake.

English

Screen Control

Setting the monitor screen.

Day/Night display setting.

7 Returns to the previous screen.

Screen Control

Display Easy Control panel

⁄

•

The Screen Control screen is displayed only when you

have applied the parking brake.

•

The picture quality can be set for each source.

You can set image quality of screens such as menu from

<Monitor Setup> (page 73) of the <Setup Menu>.

Display the Screen Control screen

Mode:Full

AV–OUT:AV–IN

SCRN

ꢀ

BAND SEEK

Preset 1

2ch

TV1

Adjust the picture quality

D I M

OFF

SYNC

NAV-SYNC

Return

1 Brightness Control

2 Tint Control

Displayed for an NTSC system image on

Video, iPod, USB or Rear View Camera.

3 Color Control

Displayed on Video, iPod, USB or Rear View

Camera screen only.

4 Contrast Control

5 Black Level Adjustment

6 Dimmer Mode Setup

"ON": The display dims.

"OFF": The display doesn’t dim.

"SYNC": Turning the Dimmer function

On or Off when the vehicle light

control switch is turned On or Off.

"NAV-SYNC" (DNX7120 only):

Turning the Dimmer function On

or Off according to the Navigation

DNX7120/DDX712/DDX7032

Hands Free Unit Control

Various functions can be used in the Hands Free control mode. (with the optional accessory Bluetooth unit

connected only)

•

You need to register your cell-phone to your Bluetooth Unit beforehand. Make sure to read the instruction manual of the

Bluetooth Unit as well

•

To use the Phonebook, it must have been downloaded from the cell-phone. For more details, see the instruction manual of

your Bluetooth Unit and your cell-phone.

The more the number of bar segments,

the stronger the signal.

: Displays the present Auto Answering

status

Control Screen Function

Displaying the control screen and using various

functions.

: When Auto Answering is on

: When Auto Answering is off

: Displays the battery drain of the cell-

phone.*

Display the Hands Free Control screen

The more the number of bar segments,

the higher the battery level.

Press the [FNC] button for more than 1 second.

2 Displays the called phone numbers.

If you have registered a phone number in

the Phonebook, the destination person

name is displayed.

3 Calls the displayed preset phone number.

4 Displays the SMS Select screen.

See <SMS (Short Message Service)> (page

61).

5 Displays the Search for Phonebook screen.

See <Calling by Phonebook> (page 54).

6 Displays the Outgoing Calls screen.

See <Making a Call Using Outgoing/

Incoming Call Records> (page 55).

7 Displays the Incoming Calls screen.

See <Making a Call Using Outgoing/

Incoming Call Records> (page 55).

8 Calls the preset phone number.

For information on how to preset a phone

number, see <Phone Number Preset> (page

60).

9 Displays the Hands Free Set Up screen.

See <Setting Up the Hands Free Phone>

(page 57).

p Displays the Dialing Display screen.

See <Calling by Entering a Phone Number>

(page 52).

1 Displays the various conditions.

: Displays short message status. If a cell-

phone which supports SMS function

is not connected, this mark does not

appear.

: There is unread short message.

: There is no unread short message.

: Downloading Phonebook.

q Starts voice recognition.

See <Calling by Voice Recognition> (page

56).

w Returns to the previous screen.

: Indicates there is a call on hold.

: Displays the signal strength.*

Next page 3

English

Hands Free Unit Control

Calling by Entering a Phone Number

⁄

•

While your car is moving, some functions are disabled for

safety’s sake. The buttons associated with the disabled

functions become ineffective if pressed.

Make a call by entering a phone number.

Display the number input screen

•

When the Hands Free Control screen appears, the name

of the connected cell-phone is displayed for 5 seconds.

* Since the number of steps of the control unit is different

from that of the cell-phone, the statuses displayed on

the control unit may discord from those displayed on

the cell-phone. No status is displayed if information

about it cannot be obtained.

•

Setting the cell-phone in the private mode can disable

the hands free function.

Enter a phone number

When Received a Call

When you receive a call, you can use the hands

free phone.

Respond to a call

1 Calls the entered phone number.

2 Creates an SMS for the entered phone

number.

See <SMS (Short Message Service)> (page

61).

3 Clears the number.

4 Returns to the previous screen.

When a call arrives, the Talking screen appears

automatically.

1 Starts conversation with a person called.

Switches the call destination if you hear a

tone of call-waiting.

Make a call

Resumes conversation with the person on

hold after completed conversation with the

other party.

You can start talking when the destination

responds.

2 Disconnects the phone.

3 Switches the voice output between phone

and speaker.

End the call

4 Outputs dial tone.

See <Controlling Tone-based Services>

(page 53).

The Hand Free screen reappears.

⁄

•

You can input max 32 digits.

DNX7120/DDX712/DDX7032

Quick Dialing

Controlling tone-based services

You can register up to 6 phone numbers for quick

dialing.

Uses tone base service using DTMF (Dual Tone

Multi Frequency).

⁄

Display the DTMF input screen

•

Phone numbers must be registered in advance.

See <Phone Number Preset> (page 60).

Display the Talking screen. See <Calling by

Entering a Phone Number> (page 52).

Recall the phone number

You can send tones during a call

Make a call

⁄

•

Only the phone numbers can be registered for Quick

Dialing. Therefore, the destination subscriber name and

others are not displayed during dialing.

1 Returns to the previous screen.

English

Hands Free Unit Control

Calling by Phonebook

Cyrillic alphabet search screen

You can call a person using his/her phone

number that you have registered in the

Phonebook.

ꢇ

ꢀ

ꢈ

ꢁ

ꢉ

ꢂ

ꢃ

ꢋ

ꢄ

ꢅ

ꢍ

ꢆ

ꢊ

ꢌ

Display the Phonebook screen

5 Displays the Phonebook beginning with

the name whose first character you have

touched.

Select the name to call

The Initial Input screen appears.

Select the Phonebook search method

You can search by the initial of the Phonebook

data.

Initial alphabet screen

6 Phonebook data list.

"REC" turns on for data with voice for voice

recognition already registered.

7 Scrolls the Phonebook data list.

8 Scrolls the name.

9 Registers the voice for voice recognition to

the selected Phonebook. If there are already

35 voice tag registered in the same cell-

phone, [Record] button is deactivated.

See <Voice Registration> (page 58).

p Plays the voice registered in the selected

Phonebook data.

1 Displays the Phonebook beginning with

the name whose first character you have

touched.

2 Scrolls the character array display.

3 Returns to the Hands Free Control screen.

q Deletes the voice registered in the selected

Phonebook data.

Touch to display the confirmation screen.

Touch [YES] to delete or [NO] to cancel.

w Displays the detail of the selected

Phonebook data.

Initial number screen

e Returns to the Initial Input screen.

Select the phone number to call

4 Displays a list of numbers in the Phonebook

starting with the selected number.

DNX7120/DDX712/DDX7032

Making a Call Using Outgoing/Incoming

Call Records

r Calls the selected phone number.

t Creates an SMS for the displayed phone

number.

Calls by selecting a phone number from the

outgoing or incoming calls list.

See <SMS (Short Message Service)> (page

61).

y Scrolls the phone number.

u Returns to the Name List screen.

i Returns to the Initial Input screen.

Display the Outgoing Calls or Incoming

Calls screen

Make a call

⁄

•

To use the Phonebook, it must have been downloaded

from the cell-phone. For more details, see the instruction

manual of your Bluetooth Unit and your cell-phone.

Initials including no corresponding name will not be

displayed.

: Outgoing Calls

: Incoming Calls

The Outgoing Calls or Incoming Calls list screen

appears.

•

During search, a non-accent character such as "u" is

searched for instead of an accent character such as "ü".

Select from calls list

Example : Outgoing Calls screen

1 Outgoing Calls list.

2 Scrolls the list.

3 Makes a call to the selected number.

4 Creates an SMS for the selected phone

number. See <SMS (Short Message

Service)> (page 61).

5 Displays the detail of the selected phone

number.

6 Returns to the Hands Free Control screen.

Make a call

⁄

•

The Outgoing Calls list screen or Incoming Calls list

screen shows the list of the calls originated from or

received at this unit. They are not the ones stored in the

cell-phone memory.

English

Hands Free Unit Control

If you hear another Beep sound:

Calling by Voice Recognition

Speak the key word within 2 seconds after the

Beep, or touch the [Phonebook List] button to

select the phone number.

Calls by recognizing the registered voice.

⁄

•

In order to perform voice recognition, voice must

be registered in the Phonebook data. See <Voice

Registration> (page 58). Or, to perform voice recognition

by Phone number category (Home, Office, Mobile etc.)

of Phonebook data, a key word voice must be registered.

See <Key Word Voice Registration> (page 59).

Make a call.

⁄

•

If there are more than one phone numbers registered

under the same name, and the key word voice is

registered for each phone number, you will hear another

beep. For how to register key word, see <Key Word Voice

Registration> (page 59).

Display the Voice Recognition screen

If there are more than one phone numbers

registered under the same name, go to step

Select a Phone number category

Utter the voice registered in the

Phonebook

4 Calls the displayed phone number.

5 Creates an SMS to the displayed address.

See <SMS (Short Message Service)> (page

61).

6 Selects the Phone number category.

7 Scrolls the phone number.

8 Returns to the previous screen.

Utter within 2 seconds after the Beep.

1 Displays the recognized phone number or

address.

2 Cancels voice recognition.

Make a call

If the voice recognition is succeeded and

there is only one phone number found:

⁄

•

A message is displayed if the voice is not recognized.

Read the message for the further operation.

Make a call.

3 Displays the phonebook list.

DNX7120/DDX712/DDX7032

"On": Beep is heard.

"Off": Beep is canceled.

6 Returns to the "Hands Free Control" screen.

7 Returns to the "Hands Free Set Up 1" screen.

8 Sets whether to use cell-phone phonebook,

outgoing calls list and incoming calls list.

Setting Up the Hands Free Phone

The Hands Free system can be set as follows.

Display the Hands Free Setup screen

(

"On")

"On": Yes.

"Off": No.

9 Sets the SMS function. ( "On")

"On": Use SMS function.

"Off": SMS not available.

p Registers the voice to select phone number

category with voice recognition.

See <Key Word Voice Registration> (page

59).

Setup each item

q Registers the phone number to Hands Free

Control screen preset button.

See <Phone Number Preset> (page 60).

w Returns to the Hands Free Control screen.

⁄

•

Either the time interval for automatic answer set on this

unit or the time interval set on the cell-phone, whichever

is shorter, takes effect.

•

Select the speaker which is further from the microphone

in order to prevent howling or echoes.

1 Moves to the "Hands Free Set Up 2" screen.

2 Sets an automatic response time after call

termination. ( "8")

"Off": This function can not use.

"0-99": Sets to calling ring time (second).

3 Sets a ringing tone output position.

(

"Front R")

"Front L": Outputs the tone from the front

left-hand side speaker.

"Front R": Outputs the tone from the front

right-hand side speaker.

"Front All": Outputs the tone from the both

front speakers.

4 Sets the beep of the incoming call.

(

"On")

"On": Beep is heard.

"Off": Beep is canceled.

5 Sets the beep of the incoming SMS.

(

"On")

English

Hands Free Unit Control

Voice Registration

End voice registration

Registers voice for voice recognition in

Phonebook. Up to 35 voices can be recorded in

one cell-phone.

Select the name to register

Go through the procedure of <Calling by

Phonebook> (page 54).

⁄

•

A message is displayed if the voice is not recognized.

Read the message for the further operation.

Repeat from 1st try if the voice is different from the 1st

try.

•

1 Selects a name.

"REC" turns on for data with voice for voice

recognition already registered.

Display the voice registration screen

Utter the voice to register (1st try)

2 Registers the voice.

3 Cancels voice registration.

Utter within 2 seconds after the Beep.

Utter the voice to register (2nd try)

DNX7120/DDX712/DDX7032

Utter the voice to register (1st try)

Key Word Voice Registration

Registers the voice to select the Phone number

category by Voice Recognition.

Display the Key Word List screen

Display the "Hands Free" screen and touch

[Setup]. See <Control Screen Function> (page

51).

6 Registers the voice.

7 Cancels voice registration.

Utter within 2 seconds after the Beep.

Utter the voice to register (2nd try)

Select the Phone number category to

End voice registration

1 Selects the Phone number category. "REC"

turns on for data with voice for voice

recognition already registered.

2 Registers voice for the selected Phone

number category.

3 Plays voice registered for the selected

Phone number category.

4 Deletes voice registered for the selected

Phone number category. Touch to display

the confirmation screen. Touch [YES] to

delete or [NO] to cancel.

⁄

•

A message is displayed if the voice is not recognized.

Read the message for the further operation.

Repeat from 1st try if the voice is different from the 1st

try.

•

5 Returns to the Hands Free Set Up screen.

Display voice registration screen

English

Hands Free Unit Control

Phone Number Preset

p Deletes the currently displayed phone

number.

q Returns to the previous screen.

Registers frequently used phone number to

Hands Free control screen preset button.

Search phone number to register with

each function

Display the Hands Free Preset List screen

Display the "Hands Free" screen and touch

[Setup]. See <Control Screen Function> (page

51)

⁄

•

Press [Delete] to delete the registered phone number.

Select the Preset number to register

1 Returns to the Hands Free Set Up screen.

Select the search destination of the

number to register

2 Registers from SMS incoming calls list.

3 Registers from SMS outgoing calls list.

4 Registers from Phonebook.

5 Registers from outgoing calls list.

6 Registers from incoming calls list.

7 Registers by entering phone numbers.

8 Registers voice for voice recognition to

preset number.

9 Registers the currently displayed phone

number.

DNX7120/DDX712/DDX7032

SMS Message screen

SMS (Short Message Service)

Uses SMS function.

Display the SMS Select screen

p Calls the number in the selected message.

q Creates a new message for the selected

message.

w Scrolls the message.

e Returns to the previous screen.

Select a function

Create a message

1 Displays received message list.

2 Displays sent message list.

r Moves the cursor.

t Displays remaining number of characters

allowed.

y Enters character.

u Changes keyboard character type.

i Sends the message.

o Sets the key layout of the character buttons.

ABC : Alphabetical key layout.

QWE : Qwerty key layout.

3 Displays the Message screen. If there is an

unfinished message, the button will be

active.

4 Retrieves SMS messages from the cell-

phone.

5 Returns to the Hands Free screen.

Select message to display

; Enters space.

a Erases the entered character.

If pressed more than 1 second, all the input

characters are erased.

s Returns to the previous screen.

6 Calls the number in the selected message.

7 Creates a new message for the selected

message.

8 Scrolls the list.

9 Displays the selected message.

English

Setup Menu

You can setup various receiver parameters.

Setup Menu

Audio Setup

Displays the setup menu to set various functions.

You can setup a speaker network, etc.

Display the control screen of any source

Display the Audio SETUP screen

Touch

in the "SETUP

Menu" screen (page 62).

⁄

•

[Audio SETUP] cannot be selected under the following

conditions:

– When no source is selected.

– When dual zone function is set to on. See <Zone

Control> (page 88)

Touch any source button on the "Source Select"

screen.

Display the SETUP Menu

Setup each item

1 Selects the speaker to set the crossover. See

<Crossover Network Setup> (page 63).

2 Sets the availability of subwoofers. See

<System Setup> (page 66).

3 Selects the type of front speakers.

"Standard": Setup for general diameter

speakers

Select the setup item

"Narrow": Setup for small diameter

speakers

"Middle": Setup for middle diameter

speakers

1 The selected setup screen appears.

2 Scrolls the setup menu.

"Wide":

Setup for large diameter

speakers

⁄

•

[Audio SETUP] and [AV Interface] options can be locked.

The key mark is displayed in reverse video for the locked

option. See <Setup Memory> (page 84).

4 Switches to the crossover setup screen.

See <Crossover Network Setup> (page 63).

5 Returns to the "SETUP Menu" screen.

DNX7120/DDX712/DDX7032

Crossover Network Setup

DVD Setup

You can set a crossover frequency of speakers.

You can setup the DVD play.

Select the speaker to set the crossover

Display the DVD SETUP screen

Touch

in the "SETUP

Menu" screen (page 62).

Setup each item

1 Sets the High Pass Filter of the front speaker.

2 Sets the High Pass Filter of the rear speaker.

3 Sets the Low Pass Filter of the sub woofer.

4 Switches to the crossover setup screen.

5 Returns to the "SETUP Menu" screen.

1 Moves to the "DVD SETUP 2" screen.

2 Selects a disc menu language.*¹

(See <Language Setup>, page 64)

3 Selects a subtitle language.*¹

(See <Language Setup>, page 64)

4 Selects an audio language.*¹

(See <Language Setup>, page 64)

Display the Crossover setup screen

Set the crossover

5 Sets the dynamic range.*¹( "Wide")

The dynamic range is reduced by changing

from "Wide" to "Normal" and from "Normal"

to "Dialog". "Dialog" makes the total sound

volume becomes larger as compared with

"Wide" and "Normal", allowing you to listen

to the movie's dialog more clearly.

This is effective only when you are using a

Dolby Digital software.

6 Sets the cross over frequency.

When front speaker or rear speaker is

selected in step 1:

The operation is available during the play

stop mode.

High Pass Filter adjustment

6 Returns to the "SETUP Menu" screen.

When Subwoofer is selected in step 1 :

Low Pass Filter adjustment

7 Sets the sub woofer phase. (Only when

"Subwoofer" is set to "ON" in Audio Setup

and "LPF SUB FREQ" is set to other than

"Through")

8 Returns to the "Audio SETUP" screen.

Next page 3

English

Setup Menu

Language Setup

Selects a language you use for the speech and

menus.

Select the language item to set

See to <DVD Setup> (page 63) and select

[Menu Language], [Subtitle Language] or

[Audio Language].

7 Returns to the "DVD SETUP 1" screen.

8 Moves to the "DVD SETUP 3" screen.

9 Sets an angle mark display. ( "On")

p Selects the screen display mode.*¹(

"16:9")

"16:9": Displays wide pictures.

"4:3 LB": Displays wide pictures in the Letter

Box format (having black stripes at

the top and bottom of screen).

"4:3 PS": Displays wide pictures in the Pan &

Scan format (showing pictures cut

at the right and left ends).

Display the Language SETUP screen

q Displays the Parental Lock screen.*¹

(

"Off")

(See <Parental Level Setup>, page 65)

w Keep "Auto" to use.*¹

e Returns to the "SETUP Menu" screen.

1 Enters a language code.

2 Cancels the language setup and returns to

the "DVD SETUP 1" screen.

3 Sets the original audio language.

(It appears during Audio Language setup.)

4 Sets the language and returns to the "DVD

SETUP 1" screen.

(It appears after you have entered a

language code.)

5 Clears the language code.

r Returns to the "DVD SETUP 2" screen.

t Selects a picture display time. *¹

Enter a language code

(

"Middle")

The Display of a JPEG picture is changed.

("Short", "Middle", "Long")

y Returns to the "SETUP Menu" screen.

See <DVD Language Codes> (page 96) and

select the desired language.

Set the language you use

⁄

•

*1 Disabled when a DVD is being played.

DNX7120/DDX712/DDX7032

Select a parental level and complete the

setup

Parental Level Setup

Sets a parental level.

Display the Parental Level code number

screen

See to <DVD Setup> (page 63) and touch

[Parental Level].

6 Selects a parental level.

7 Complete the parental level setup and

returns to the "DVD SETUP 2" screen.

⁄

•

If a disc has higher parental lock level, you need to enter

the code number.

The parental lock level varies depending on a loaded

disc.

If a disc has no parental lock, anybody can play it back

even when you have set the parental lock.

Enter the code number

1 Enters a code number.

2 Cancels the current setup and returns to

the "DVD SETUP 2" screen.

3 Indicates the present parental lock level.

4 Determines the code number and displays

the Parental Level setup screen.

5 Clears the code number.

⁄

•

The number you enter first is set as your code number.

You can clear the code number by pressing the Reset

button.

Display the Parental Level SETUP screen

English

Setup Menu

System Setup

You can setup the system parameters.

Display the SETUP System screen

Touch

in the "SETUP

Menu" screen (page 62).

Setup each item

7 Returns to the "SETUP System 1" screen.

8 Sets the function of the [NAV] button.

"V. OFF" : Press the [NAV] button for more

than 1 second to turn the display

off.

"R. CAM": Press the [NAV] button for more

than 1 second to switch to rear

view.

9 Returns to the "SETUP Menu" screen.

1 Moves to the "SETUP System 2" screen.

2 Turns the key touch tone On or Off.

(

"On")

3 Allows scrolling of text display on the

Source Control screen. ( "Auto")

"Auto":

Scrolls the screen automatically.

"Manual": Allows you to scroll the screen

manually.

4 Selects a remote control signal. ( "On")

When turned "Off", the remote control of TV

reception is rejected.

5 Sets a music CD playback. ( "1")

"1": Automatically recognizes and plays

back an Audio file disc, a DVD or a

music CD.

"2": Forcibly plays back a disc as a music

CD. Select "2" if you wish to play a

music CD having a special format or

if you cannot play a disc in the "1"

position.

6 Returns to the "SETUP Menu" screen.

⁄

•

You cannot play an Audio file/VCD disc in the "2"

position. Also, you may not play some music CDs in the

"2" position.

•

Your setup is disabled when the disc is being played.

DNX7120/DDX712/DDX7032

AV Interface Setup

You can set audio and visual (AV) interface

parameters.

Display the AV Interface screen

Touch

in the "SETUP

Menu" screen (page 62).

6 Returns to the "AV Interface 1" screen.

7 Moves to the "AV Interface 3" screen.

8 Selects an AV source to be output at the AV

OUTPUT port. ( "AV-IN")

9 Sets a method to switch to the rear view

camera video display. ( "Off")

Setup each item

"On": Switches to the rear view camera

video display when engaging the

shift knob of car to "Reverse".

"Off": Switches to the rear view camera

video display when engaging the

shift knob of car to "Reverse" and

1 Moves to the "AV Interface 2" screen.

2 Sets a name to be displayed when you

select a system that is connected via the AV

INPUT port. ( "VIDEO")

3 Sets an image display of the system that is

connected via the AV INPUT port.

then pressing the [NAV] button for

more than 1 second.

p You can flip the left and right of the rear

view camera video display. Set to "On" and

the the rear view will be displayed left and

right in mirror image on the screen.

(

"Off")

"Off": When the image source is switched,

an image entered via the AV INPUT

port is displayed.

(

"Off")

q Returns to the "SETUP Menu" screen.

"On": When an image signal is entered

via the AV INPUT port, this image is

displayed.

4 Selects a navigation system connection.

(

"RGB") (DDX712/DDX7032 only)

"RGB": Allows the Kenwood's Navigation

System to connect via the AV INPUT

port.

"AV-IN": Allows a third-party navigation

system to connect via the AV INPUT

port.

w Returns to the "AV Interface 2" screen.

e Selects speakers used for voice guidance of

the navigation system. ( "F-Left")

"Off": Must be used if no navigation system

is connected. (The navigation display

is cancelled when the AV source is

switched.)

"F-Left":

Uses the front left side speaker

for voice guidance.

5 Returns to the "SETUP Menu" screen.

"F-Right": Uses the front right side speaker

for voice guidance.

"Front All": Uses both front speakers for

voice guidance.

r Adjusts the volume for voice guidance of

the navigation system. ( "21")

Next page 3

English

Setup Menu

t Mutes the volume during voice guidance of

User Interface

the navigation system. ( "On")

When turned "On", the volume level drops

for voice guidance.

You can setup user interface parameters.

Display the User Interface screen

y Sets the voice guidance method of the

Navigation system. ( "On")

(DNX7120 only)

Touch

Menu" screen (page 62).

in the "SETUP

"On" : Voice guidance is On.

"Off" : Voice guidance is Off.

u Returns to the "SETUP Menu" screen.

Setup each item

1 Moves to the "User Interface 2" screen.

2 Selects the background to display.

"Change": Displays images entered into

this unit. Refer to <Background

Select> (page 71).

3 Enables entering or deleting of background

images into or from this unit.

Press

to enter the USB suspend

mode, and then remove the USB device.

"Memory": Enables entering of background

images. Refer to <Entering

Background> (page 70).

"Delete": Enables deleting of background

image entered into this unit.

Refer to <Background Delete>

(page 71).

4 Registers the source displayed in the

favorite source screen.

See <Direct Source Button Setup> (page

70).

5 Returns to the "SETUP Menu" screen.

6 Returns to the "User Interface 1" screen.

7 Moves to the "User Interface 3" screen.

8 Sets an on-screen display of the iPod

DNX7120/DDX712/DDX7032

Playback screen. ( "Auto")

"Auto": Information is displayed for 5

seconds when updated.

"Manual": Information is displayed when you

touch on the screen.

9 Sets an on-screen display of the navigation

screen. ( "Off")

"Auto": Information is displayed for 5

seconds when updated.

"Off": Information is not displayed.

p Sets an on-screen display of the video

playback screen. ( "Auto")

u Returns to the "User Interface 3" screen.

i Sets whether to display animation when

switching screens. ( "On")

o Sets whether to display the name of the

"Auto": Information is displayed for 5

seconds when updated.

"Manual": Information is displayed when you

touch on the screen.

, and

buttons on

the right side of the menu screen.

; Sets whether to display the target when

touching the panel.

q Returns to the "SETUP Menu" screen.

a Returns to the "SETUP Menu" screen.

w Returns to the "User Interface 2" screen.

e Moves to the "User Interface 4" screen.

r Sets an on-screen display of the TV screen.

(

"Auto") (with the optional accessory TV

tuner connected only)

"Auto": Information is displayed for 5

seconds when updated.

"Manual": Information is displayed when

you touch on the screen.

t Sets an on-screen display of the DVD

Playback screen. ( "Manual")

"Auto": Information is displayed for 5

seconds when updated.

"Manual": Information is displayed when you

touch on the screen.

y Returns to the "SETUP Menu" screen.

English

Setup Menu

Direct Source Button Setup

Entering Background

Registers the source displayed in the favorite

source screen.

Loads a image for background.

Connect the device which has the image to

load

Displays the Direct SRC button Setup

screen

Display the User Interface screen

Touch

in the "SETUP

Menu" screen (page 62).

Display the Background Memory screen

See <User Interface> (page 68).

Select a preset button

Select the image to load

1 Selects the preset button to register.

2 Selects the source to register.

3 Scrolls the source button list.

1 Lists the files.

2 Scroll the list.

4 Returns to the "User Interface 4" screen.

3 Returns to Media Select screen.

4 Returns to the previous folder.

5 Returns to the "User Interface" screen.

Select a source to register

Load the image

Complete the registration

6 Rotates the image.

7 Returns to the Picture Select screen.

⁄

•

Refer to <About Picture files> (page 8) for readable

image specifications.

•

Up to 3 images can be loaded.

This operation is not possible when USB is selected as the

source.

DNX7120/DDX712/DDX7032

Background Delete

Background Select

Deletes the background image.

Selects a image for background.

Display Delete Image Select screen

1 Select Background Change screen

Select the image to be deleted

2 Select a image for background

1 Returns to the initial background.

2 Returns to the original screen.

1 Returns to the original screen.

Delete the image

Set the image as the background

Confirm

2 Returns to the Pictrue Select screen.

English

Setup Menu

Touch Panel Adjustment

Clock Setup

You can adjust the touch panel operations.

You can adjust the clock time.

Display the Touch panel Adjustment

screen

Display the Clock Setup screen

Touch

in the "SETUP

Touch

in the "SETUP

Menu" screen (page 62).

Setup the Clock

Start Touch panel setup

1 Clock time display

2 Adjusts hours.

1 Returns to the "SETUP Menu" screen.

3 Adjusts minutes.

4 Sets "00" minute.

Adjust the Touch panel

Setup examples: 3:00 – 3:29 \ 3:00

3:30 – 3:59 \ 4:00

5 Sets the clock time in synchronization with

the time data sent from the navigation

system or the RDS station.

(

DNX7120: "Navigatoin",

DDX712/DDX7032: "On")

When the synchronized mode is set, the

clock cannot be adjusted manually.

6 Returns to the "SETUP Menu" screen.

Follow the instruction on the screen and touch

the center of

2 Cancels the adjustment and returns to the

Touch Panel Adjust screen.

Adjust the clock time

3 Resets to the initial status.

DNX7120/DDX712/DDX7032

p Stores the current monitor angle as the

angle during power off.

q Returns to the "SETUP Menu" screen.

Monitor Setup

You can adjust the position, picture quality and

the screen mode of the monitor.

Displaying the Monitor SETUP screen

Touch

in the "SETUP

Menu" screen (page 62).

Setup each item

w Returns to the "Tilt Control" screen.

e Moves to the "Mode Select 2" screen.

r Selects a screen mode of the iPod VIDEO

playback screen.

You can select any of the following screen

mode.

"Full", "Just", "Zoom", "Normal"

t Selects a screen mode of the DVD playback

screen.

You can select any of the following screen

mode.

"Full", "Just", "Zoom", "Normal"

y Selects a screen mode of the VIDEO

playback screen.

You can select any of the following screen

mode.

"Full", "Just", "Zoom", "Normal"

u Selects a screen mode of the TV screen.

You can select any of the following screen

mode.

1 Moves to "Tilt Control" screen.

2 Brightness control

3 Contrast Control

4 Black Level Adjustment

5 Dimmer Mode Setup

"ON": The display dims.

"OFF": The display doesn’t dim.

"SYNC": Turning the Dimmer function

On or Off when the vehicle light

control switch is turned On or Off.

"NAV SYNC": Turning the Dimmer function

On or Off according to the

Navigation Day/Night display

setting.

6 Returns to the "SETUP Menu" screen.

⁄

"Full", "Just", "Zoom", "Normal"

i Returns to the "SETUP Menu" screen.

•

In this Screen Control screen, you can perform setups for

the menu screen. Setups for videos such as DVD can be

performed on the <Screen Control> (page 50).

o Returns to the "Mode Select 1" screen.

; Selects a screen mode of the rear view

camera (R-CAM) screen.

7 Returns to the "Screen Control" screen.

8 Moves to "Mode Select 1" screen.

9 Sets the Monitor angle.

You can select any of the following screen

Next page 3

English

Setup Menu

mode.

Security Code Setup

"Full", "Just", "Zoom", "Normal"

You can set a security code to protect your

receiver system against theft.

a Returns to the "SETUP Menu" screen.

⁄

•

When you select the Menu or Navigation, the display is

shown in the full-size display mode automatically. The

screen mode of these displays cannot be changed.

The picture qua¡lity can be set for each source.

When the Security Code function is activated, the code

cannot be changed and the function cannot be released.

Note the Security Code can be set as the 4 digit number

of your choice.

•

Full picture mode ("Full")

Display the Security Code Setup screen

Touch

in the "SETUP

Menu" screen (page 62).

Justify picture mode ("Just")

Zoom picture mode ("Zoom")

Normal picture mode ("Normal")

1 Displays the Security code input screen.

2 Turns the SI function on or off.

If turned "On", the burglar alarm lamp

flashes when the vehicle ignition is off.

(

"On")

3 Returns to the original screen.

Start Security Code setup

⁄

•

If you have already completed the code registration,

Clear

is displayed.

Enter a security Code

Input four-digit number.

DNX7120/DDX712/DDX7032

If you have pressed the Reset button or if

you have disconnected the Receiver from

battery...

Reenter the security code

Enter the correct security code

Reenter the same security code as that you

have entered in Step 3 for confirmation.

⁄

•

If you enter a different security code, the screen returns

to Step 3 (for the first code entry).

You must enter the same security code as that

you have entered in Step 3.

Enter the security code

Now, your security code is registered.

If you press the Reset button or if you

disconnect your receiver from the battery after

the code registration, you need to enter the

registered security code.

Now, you can use your Receiver.

English

Setup Menu

Deactivating Security Code

iPod Setup

To deactivate the Security Code function.

Performs setup when using iPod.

Display Security Code Setup screen

Display the iPod SETUP screen

Touch

in the "SETUP

Touch

in the "SETUP

Menu" screen (page 62).

Start to cancel a registration of the

Security Code

Setup each item

1 Sets the Audio book playback speed.

2 Sets Wide Screen on or off.

3 Returns to the "SETUP Menu" screen.

Enter a security Code

⁄

•

"Wide Screen" cannot be set while the iPod is connected.

Input by four-digit number.

Now, your security code is cleared.

DNX7120/DDX712/DDX7032

Sirius Setup

Sirius Parental Code Setup

You can setup the Parental lock for Sirius.

Sets a Sirius Parental code.

Display the Sirius Setup screen

Display the Parental Code screen

Touch

in the "SETUP

Menu" screen (page 62).

⁄

•

If you have already completed the code registration,

Change is displayed.

•

If you to clear the code which has already registered,

press Clear

1 Sets the Parental lock code.

Enter the current code number

See <Sirius Parental Code Setup> (Page 77).

2 Switch the Parental lock function on and off.

See <Sirius Parental Lock Setup> (Page 78).

3 Sets the channel to set parental lock.

See <Sirius Parental Lock Channel Select>

(Page 79).

4 Returns to the "SETUP Menu" screen.

1 Enters a code number.

2 Cancels te current setup and returns to the

SIRIUS Setup screen.

3 Determines the code number and displays

the Parental Code 1st screen.

4 Clears the code number.

5 Returns to the "SIRIUS SETUP" screen.

⁄

•

If you are to register the parental code for the first time,

this screen will not appear. Go to Step 3.

Enter the new code number

Next page 3

English

Setup Menu

Confirm the code number

Sirius Parental Lock Setup

Sets a Sirius Parental Lock function on or off.

Enter the same code number as you input in

step 3.

Display the Parental Code screen

Sirius Parental code is now set, and the display

returns to "SIRIUS SETUP" screen.

⁄

•

You need to complete <Sirius Parental Code Setup>

beforehand.

Enter the code number

Enter the same code number as you input in

<Sirius Parental Code Setup>.

Parental Lock function is now set to on or

off, and the display returns to "SIRIUS SETUP"

screen.

⁄

•

If you have not registered the parental code, the code

number you input in this step will be the number to

requested to input the code once more.

DNX7120/DDX712/DDX7032

Set the parental lock for each channel

Sirius Parental Lock Channel Select

Selects the channel to enable Sirius Parental lock

function.

Display the Parental Code screen

5 Lists the channel.

The channel name scrolls by pressing

6 Scrolls the channel list.

7 Sets the Parental lock function on or off for

each channel.

You need to input the Parental code to

switch the Parental lock function on or off.

8 Displays the sort sequence

9 Switch the sort sequence of the channel list.

("Channel", "Category", "Song title", "Artist"

and "Composer")

Enter the code number

Enter the same code number as you input in

<Sirius Parental Code Setup>.

p Moves to SIRIUS Category Select Setup

screen.

q Returns to the "SIRIUS SETUP" screen.

Select a category

1 Lists the category.

The category name scrolls by pressing

2 Scrolls the category list.

3 Displays all the channels.

4 Returns to the "SIRIUS SETUP" screen.

English

Setup Menu

Bluetooth Setup

Registering Bluetooth Unit

Registers and selects Bluetooth unit.

Registers the Bluetooth unit to be connected.

Display the Bluetooth Setup screen

1 Display the Connect Device List screen

Touch

in the "SETUP

Menu" screen (page 62).

Setup each item

Search for a Bluetooth unit

1 Sets cell-phone for Hands Free and Audio

player for Bluetooth Audio.

2 Sets the PIN code of the Bluetooth unit to

enter when registering (pairing) from the

cell-phone or audio player side.

1 Displays the registered Bluetooth unit.

Displays the busy service in blue. Displays

the available service in gray.

3 Returns to the "SETUP Menu" screen.

2 Scrolls the name of the Bluetooth unit.

3 Searches for Bluetooth unit.

4 Registers Bluetooth unit that cannot be

registered by normal register (paring)

operation.

5 Returns to the previous screen.

⁄

•

A new device cannot be registered if there are 5

registered Bluetooth units. Delete unnecessary

registration. See <Deleting Bluetooth Unit> (page 83).

Select the Bluetooth unit to register

6 Displays the searched Bluetooth unit.

7 Scrolls the name of the Bluetooth unit.

8 Cancels searching of Bluetooth unit.

9 Starts search.

p Scrolls.

q Returns to the previous screen.

DNX7120/DDX712/DDX7032

Enter PIN code

Registering Bluetooth Unit PIN Code

Sets the PIN code of the Bluetooth unit to enter

when registering (pairing) from the cell-phone or

audio player side.

Enter the PIN code specified for the Bluetooth

unit to register.

Display the Receiver PIN Code screen

w Enters a code number.

e Cancels registration of PIN code.

r Enters PIN code.

t Clears the code number.

Enter PIN code

⁄

•

You can also register from the Bluetooth unit side. For

the PIN code necessary for registration, see <Registering

Bluetooth Unit PIN Code> (page 81).

•

If the error message appears even though the PIN code

is correct, try <Registering Special Bluetooth Unit> (page

82).

1 Enters a code number.

2 Cancels registration of PIN code.

3 Enters PIN code.

4 Clears the code number.

English

Setup Menu

Registering Special Bluetooth Unit

Bluetooth Unit Connection

Registers Special Bluetooth unit that results in

error by normal operation by selecting from

model name.

Selects the Bluetooth unit to connect.

Display the Connect Device List screen

Display the Special Device List screen

Select a registered Bluetooth unit

Select a model name

1 Displays the registered Bluetooth unit.

2 Scrolls the name of the Bluetooth unit.

3 Returns to the previous screen.

1 Displays the Bluetooth unit name that can

be registered.

2 Scrolls the name of the Bluetooth unit.

3 Scrolls.

Select the service to use

4 Returns to the previous screen.

Confirm whether to register

4 Connects/disconnects cell-phone to use for

Hands Free.

5 Connects/disconnects Audio player to use

for Bluetooth Audio.

6 Deletes registration (pairing).

7 Returns to the previous screen.

5 Cancels registration.

⁄

•

Only models in Bluetooth unit name list can be

registered.

Go through the procedure of <Registering

Bluetooth Unit> (page 80) and complete

the registration (pairing).

DNX7120/DDX712/DDX7032

Deleting Bluetooth Unit

DivX Setup

Deletes the registered Bluetooth unit.

Checks the registration code. This code is needed

when making a disc which has DRM (Digital

Rights Management).

Display the Connect Device List screen

Display the DivX Setup screen

Touch

in the "SETUP

Menu" screen (page 62).

Select a Bluetooth unit to delete

1 Displays the registration code.

⁄

•

When downloading a DivX VOD file controlled by DRM,

one above. Otherwise the file may not be able to play

with this unit. Remaining number of viewing is displayed

when playing a DivX VOD file with the viewing restriction.

When the remaining number of viewing reached 0, a

warning message appears and the file cannot be played.

Delete the Bluetooth unit

Confirm deleting of Bluetooth unit

English

Setup Menu

Memorize or recall the settings

Setup Memory

Audio Setup and AV Interface settings can be

memorized. The memorized settings can be

recalled at any time. For example, even when the

settings are cleared due to replacement of the

battery, the settings can be restored.

When memorizing the Audio Setup and AV

Interface settings:

Display the SETUP Memory screen

If settings have already been memorized, a

Yes

Setup Memory

confirmation message appears. Touch

Touch

in the "SETUP

To cancel memorization, touch

Menu" screen (page 62).

When recalling the memorized settings:

Touching the screen displays a confirmation

Yes

message. Touch

. To cancel recalling,

touch

When clearing the currently memorized

settings:

1 Locks the Audio Setup and AV Interface

Lock

settings. When

is selected, you

cannot set the Audio Setup and AV

Interface settings.

2 Memorizes or recalls the settings. To cancel

Touching the screen displays a confirmation

Yes

the function, touch

memorization, touch

. To cancel

message. Touch

. To cancel clearing,

touch

The SETUP Menu screen appears again.

3 Returns to the original screen.

Quit memorization/recalling of settings

Start Setup Memory

4 Recalls the memorized settings.

5 Memorizes the current Audio Setup and AV

Interface settings.

6 Clears the currently memorized settings.

7 Returns to "SETUP Memory" screen.

DNX7120/DDX712/DDX7032

Setting EXT SW Control 2 (EXT SW2)

EXT SW Setup

Setting up power specification of the external

device for which the power is controlled from

this unit.

Display the EXT SW SETUP screen

Touch

in the "SETUP

Menu" screen (page 62).

The setup method is the same as "EXT SW1".

Perform EXT SW Setup

Setting EXT SW Control 1 (EXT SW1)

1 Sets the name of the external device. See

<Character Entry> (page 49) for information

on how to enter the name.

2 Sets the power signal output mode.

(

EXT SW1: Pulse, EXT SW2: Level)

Pulse: Generates a single power signal

pulse.

Level: Continues output of high power

signal.

Sets to turn output on/off each time the

button on the EXT SW Control screen is

pressed.

3 Sets the Pulse signal output time.

Outputs 500ms when "1" is set. Increases

by 200ms with each step. Up to 100 steps

can be set.

4 Returns to the original screen.

English

Audio Control

Audio Control Menu

Audio Control

Displays the Audio Control menu to set the sound

effect function of this unit.

You can adjust the front/rear and right/left audio

balance.

Display the control screen of any source

Display Audio Control screen

Touch

in the "Audio

Control Menu" screen (page 86).

Set the each item

Press several times until the control screen

appears.

Display the Audio Control menu

1 Moves to the "Audio Control 2" screen.

2 Adjust the front/back and left/right volume

around the touched area.

3 Adjusts the right and left volume balance.

4 Adjusts the front and rear volume balance.

5 Turns the Loudness control function On or

Off.

Select the Audio Control item

If turned "On", high and low tones are

automatically enhanced during low volume.

6 Displays the present source information.

The stream (Dolby Digital, dts, Linear PCM,

MPEG, MP3, WMA or AAC) is displayed.

7 Returns to the "Audio Control Menu" screen.

1 Switches to the selected Audio Control

screen.

8 Returns to the "Audio Control 1" screen.

9 Adjusts the volume of the present source

based on the difference level of original

volume.

DNX7120/DDX712/DDX7032

p Adjusts the subwoofer volume.

q Returns to the "Audio Control Menu" screen.

Equalizer Control

You can setup the equalizer.

⁄

Display Equalizer Control

•

If you have increased the volume first, then reduced the

volume using the "Vol. Offset", the sound generated if

you suddenly switch to another source may be extremely

loud.

Touch

in the "Audio

Control Menu" screen (page 86).

•

You may not set some models of power amp boost to

"+18". See the catalog or instruction manual of power

amplifier.

Display the Equalizer screen

1 Selects an equalizer curve type.

You can select any of the following

equalizer curves.

• "Natural"

• "Rock"

• "Pops"

• "Easy"

• "Top40"

• "Jazz"

• "User"

⁄

•

"User" can be selected after tone adjustment is carried

out. See <Tone Setup> (page 88).

2 Selects items to be adjusted for tone curve

setup.

If turned "Off", only Level can be setup for

tone curves.

3 Displays the Tone curve setup screen. (page

88)

4 Returns to the "Audio Control Menu" screen.

English

Audio Control

Tone Setup

Zone Control

You can set a Tone curve.

You can set the front and rear audio source.

Display the Tone screen

Display Zone Control

Touch

in the "Audio

Control Menu" screen (page 86).

See <Equalizer Control> (page 87).

Set the Tone

1 Displays the current source.

2 Returns to the "Audio Control Menu" screen.

Set the Zone Control

1 Tone curve becomes flat.

2 Bass adjustment items are displayed.

3 Middle adjustment items are displayed.

4 Treble adjustment items are displayed.

5 Sets the Center frequency.

6 Sets the level.

3 Turns the Zone Function (that sets different

source sounds for front and rear speakers)

On or Off.

7 Sets the Q factor. (Only Bass and Middle can

be set)

8 Bass DC Extend settings. (Only when Bass is

selected)

4 Switches the front and rear audio sources.

(This button appears when the Zone

function is On.)

If turned "On", it extends the bass

center frequency to the low register by

approximately 20%.

Use "Reverse" to change over the front and

rear audio sources.

9 Returns to the "Equalizer" screen.

5 Sets the front and rear audio source

separately.

(This button appears when the Zone

function is On.)

⁄

•

When the rear speaker sound is switched, the audio

source that is output at the AV OUTPUT terminal is also

switched to the same source.

6 Adjusts the volume of the rear channel.

(This button appears when the Zone

function is On.)

7 Returns to the "Audio Control Menu" screen.

DNX7120/DDX712/DDX7032

⁄

•

There are following limitations when zone function is set

to "On".

- There is no output from the subwoofer.

- <Audio Setup> (page 62) and <Equalizer Control>

(page 87) are not available.

English

Remote Controller

This unit can be operated using the Remote Controller (DNX7120; RC-DV330, DDX712/DDX7032; RC-DV340)

supplied with the unit.

•

Put the Remote Controller in a place where it will not move during braking or other operations. A dangerous situation could

result, if the Remote Controller falls down and gets wedged under the pedals while driving.

Do not place the battery near an open flame or heat source. This may cause the battery to explode.

Do not recharge, short, break up or heat the battery or place it in an open fire. Such actions may cause the battery to leak

fluid. If spilled fluid comes in contact with your eyes or on clothing, immediately rinse with water and consult a physician.

Place the battery out of reach of children. In the unlikely event that a child swallows the battery, immediately consult a

physician.

•

Battery installation

Remote Controller mode switch

Use two "AAA"/"R03"-size batteries.

Insert the batteries with the + and – poles aligned

properly, following the illustration inside the case.

The functions operated from the remote

controller differ depending on the position of the

mode switch.

RC-DV330

AUD mode

Switch to this mode when

controlling a selected source or

tuner source, etc.

POSITION

DVD mode

Switch to this mode when playing

AUD

DVDs or CDs etc. with the player

integrated in this unit.

TV mode

This is switched when controlling

TV.

•

DVD

NAVI

RETURN

NAVI mode

This is switched when controlling

Navigation unit.

CANCEL

⁄

•

If the Remote Controller operates only over shorter

distances or does not operate at all, it is possible that

the batteries are depleted. In such instances, replace the

both batteries with new ones.

RC-DV340

AUD mode

Switch to this mode when

controlling a selected source

or tuner source, etc.

AUD

•

DVD mode

DVD

Switch to this mode when

playing DVDs or CDs etc.

with the player integrated in

this unit.

TV mode

This is switched when

controlling TV.

⁄

•

The position of the remote control mode switch is

indicated in the title of each mode, e.g., "(AUD mode)".

When controlling a player that is not integrated in the

unit, select "AUD" mode.

•

DNX7120/DDX712/DDX7032

Display angle

Switches the display angle each time it is pressed.

Common operations (AUD mode)

[RC-DV330]

[RC-DV340]

NAVI

AUD•

DVD•

TV•

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

ENTER

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

Source switching

Switches to the source to be played.

SUBTITLE

ANGLE

MAP DIR

AM−

OPEN

VOL

ꢄ

VOL

DISP

SRC

V.SEL

SRC

V.SEL

ZOOM

OUT

MODE FNC/PBC

ꢃ

ꢁꢂ

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

POSITION

Cursor key

AUD

AUDIO

SUBTITLE

•

DVD

Moves the cursor when displaying menu.

ENTER

ꢁꢂ

ꢃ

ZOOM

ꢁꢂ

ꢃ

ꢁꢂ

OUT

POSITION

Volume control

AUD

DVD

•

AUD

•

ENTER

DVD

Adjusts the volume.

ENTER

VIEW

MAP DIR

NAVI

ANGLE

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

AM−

OPEN

ꢄ

AM−

OPEN

VOL

ZOOM

ꢄ

ꢅ

−

ꢅ

2ZONE

ENTER

Enters options.

2ZONE

2^ABC3DEF

ꢃ

ꢁꢂ

POSITION

ꢁꢂ

ꢃ

Volume attenuator

Press the key once to lower the volume. Press again

OUT

AUD

DVD

•

DVD

ENTER

to restore the previous volume.

NAVI

R.VOL

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

R.VOL

AM−

OPEN

PQRS 8^TUV9WXYZ

ꢀ

7PQRS 8^TUV9WXYZ

ꢀ

CLEAR

DIRECT

ATT

CLEAR

DIRECT

ATT

Hands-free communication

Enters the dialing method selection mode.

When a call comes in, it answers the call.

Dual Zone

AUDIO RETURN

CANCEL

MODE/TOP MENU FNC/MENU/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

AM−

OPEN

Switches the Dual Zone function ON and OFF.

SUBTITLE

VOL

MAP DIR

−

OPEN

ꢄ

^FM+

ꢄ

ꢅ

2ZONE

ꢁ

VOL

ANGLE

ZOOM

ꢄ

ꢅ

2^ABC3DEF

−

VOL

ꢆ

ꢅ

2ZONE

2ABC 3DEF

2^ABC3DEF

ꢆ

ꢁ

4GHI 5JKL 6MNO

Function

R.VOL

Switches the function screen.

•

Rear volume control

Adjusts volume at rear when the Dual Zone

ENTER

•

DISP

•

NAVI

SRC

V.SEL

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

MODE FNC/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

function is ON.

2ZONE

SUBTITLE

AUDIO

SUBTITLE

2ZONE

MAP DIR

2^ABC3DEF

ꢆ

ANGLE

ꢁꢂ

ꢃ

ꢁ

R.VOL

ꢀ

ꢁ

R.VOL

ꢀ

4GHI 5JKL 6MNO

7PQRS 8^TUV9WXYZ

MODE

Switches the screen mode.

PQRS 8^TUV9WXYZ

CLEAR

DIRECT

CLEAR

DIRECT

ATT

Screen mode changes each time you press this key.

•

V.SEL

•

NAVI

AUDIO RETURN

CANCEL

DISP

SRC

V.SEL

Switches to the navigation screen.

MODE/TOP MENU FNC/MENU/PBC

MODE FNC/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

SUBTITLE

DISP

MAP DIR

AUDIO

SUBTITLE

SRC

V.SEL

SRC

MODE FNC/PBC

V.SEL

ANGLE

ZOOM

OUT

ꢃ

ꢁꢂ

ꢄ

ꢁꢂ

ꢃ

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

POSITION

AUD

AUDIO

SUBTITLE

•

DVD

ENTER

ꢁꢂ

ꢃ

English

Remote Controller

DVD/VCD/CD/Audio files (DVD mode)

Track number

Play time

Cancel

[RC-DV330]

[RC-DV340]

Folder search

Selects the folder to be played.

Audio files

ANGLE

ꢄ

AM−

OPEN

VOL

ZOOM

VOL

Folder number

File number

Cancel

−

ꢄ

ꢅ

2ZONE

2^ABC3DEF

2ZONE

2^ABC3DEF

ꢆ

Track search and file search

Selects the track or file to be played.

VCD 1.X, VCD 2.X (PBC OFF)

VIEW

MAP DIR

ANGLE

ZOOM

Track number

Cancel

AM−

OPEN

ꢄ

VOL

ꢄ

ꢅ

−

ꢅ

2ZONE

2^ABC3DEF

ꢆ

VCD 2.X (PBC ON)

Play/Pause

Pauses the track.

Press again to resume playing.

Scene number

Number

Cancel

TOP MENU

AUDIO

DVD SETUP

ANGLE

RETURN

ZOOM

DISP

SRC

V.SEL

SUBTITLE

ZOOM

OUT

ꢃ

ꢁꢂ

ꢃ

POSITION

Once you have switched to the direct search

feature, specify the search number from the

AUD

•

AUD

•

DVD

ENTER

numeric keypad, and then press [ENTER] key.

Stop

Numeric keypad

Memorizes the last point where the disc stopped.

When pressed again, the last point is deleted.

2ZONE

ꢅ

2ZONE

2^ABC3DEF

ꢆ

ꢁ

R.VOL

ꢀ

ꢁ

R.VOL

ꢀ

4GHI 5JKL 6MNO

TOP MENU

AUDIO

DVD SETUP

ANGLE

RETURN

ZOOM

DISP

SRC

V.SEL

SUBTITLE

7PQRS 8^TUV9WXYZ

PQRS 8^TUV9WXYZ

ZOOM

OUT

ꢃ

ꢁꢂ

CLEAR

DIRECT

ꢁꢂ

ꢃ

POSITION

CLEAR

DIRECT

ATT

AUD

•

AUD

•

DVD

ENTER

•

Specify the number to search in direct search.

Direct search

R.VOL

2ABC

Press

to fast forward/backward.

R.VOL

PQRS 8^TUV9WXYZ

ꢀ

PQRS 8^TUV9WXYZ

ꢀ

CLEAR

DIRECT

Switches the fast forward/backward speed each

time you press this key.

ATT

CLEAR

DIRECT

ATT

•

Press

4GHI

5JKL

to slow forward/backward.

Switches the slow playback speed each time you

press this key.

Pressing this button switches the features that can

be searched directly.

DVD Top Menu

Returns to the DVD top menu.

DVD

•

Title number

Chapter number

Play time

Item number*

Cancel

•

DISP

NAVI

SRC

V.SEL

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

MODE FNC/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

SUBTITLE

AUDIO

SUBTITLE

MAP DIR

ANGLE

ꢁꢂ

ꢃ

* You may not be able to use this function with some discs

or scenes.

DNX7120/DDX712/DDX7032

DVD Menu

Displays the DVD menu.

Turns the playback control on or off while playing

Radio (AUD mode)

[RC-DV330]

[RC-DV340]

VCD.

Band switching

Switches to bands received by the unit.

ENTER

•

DISP

•

NAVI

AUDIO RETURN

CANCEL

SRC

V.SEL

MODE/TOP MENU FNC/MENU/PBC

MODE FNC/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

ANGLE

SUBTITLE

ꢄ

AUDIO

SUBTITLE

AM−

OPEN

MAP DIR

VOL

ZOOM

VOL

ANGLE

ꢁꢂ

ꢃ

−

ꢄ

ꢅ

2ZONE

2^ABC3DEF

2ZONE

2^ABC3DEF

SUBTITLE

ꢆ

Switches the subtitle language.

NAVI

Station selection

DISP

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

SRC

V.SEL

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

Switches to broadcast stations received by the unit.

MODE FNC/PBC

SUBTITLE

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

VIEW

MAP DIR

ANGLE

ZOOM

ANGLE

ZOOM

AUDIO

SUBTITLE

AM−

OPEN

ꢄ

VOL

ꢁꢂ

ꢃ

ꢄ

ꢅ

−

ꢅ

2ZONE

2^ABC3DEF

ꢆ

ZOOM

Switches the zoom ratio each time you press this

Direct tuning

After pressing this key, use the keypad to specify

key.

VIEW

MAP DIR

DISP

ANGLE

ZOOM

the broadcast station you wish to receive.

SRC

V.SEL

ꢄ

MODE FNC/PBC

R.VOL

VOL

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

R.VOL

PQRS 8^TUV9WXYZ

ꢀ

7PQRS 8^TUV9WXYZ

ꢀ

−

CLEAR

DIRECT

AUDIO

SUBTITLE

ꢅ

2ZONE

ATT

CLEAR

DIRECT

ATT

2^ABC3DEF

ꢁꢂ

ꢃ

Picture Angle

Switches the picture angle each time you press this

Example: 92.1MHz (FM)

9WXYZ

2ABC

key.

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

DISP

Example: 810kHz (AM)

SUBTITLE

ANGLE

ZOOM

SRC

V.SEL

MAP DIR

MODE FNC/PBC

TOP MENU

DVD SETUP

ANGLE

RETURN

ZOOM

8TUV

ꢄ

AUDIO

SUBTITLE

VOL

−

ꢁꢂ

ꢃ

Numeric keypad

ꢅ

2ZONE

ꢅ

2ZONE

2^ABC3DEF

ꢆ

AUDIO

Switch Voice Language

ꢆ

ꢁ

R.VOL

ꢀ

ꢁ

R.VOL

ꢀ

4GHI 5JKL 6MNO

7PQRS 8^TUV9WXYZ

PQRS 8^TUV9WXYZ

CLEAR

DIRECT

Switches the voice language each time you press

this key.

CLEAR

DIRECT

ATT

DVD

•

DISP

ENTER

•

To use preset tuning, press the number of a

programmed broadcast station. (

Press the direct tuning key first, then specify the

frequency of the station to receive.

•

SRC

V.SEL

NAVI

AUDIO RETURN

CANCEL

MODE FNC/PBC

MODE/TOP MENU FNC/MENU/PBC

TOP MENU

AUDIO

DVD SETUP

ANGLE

RETURN

ZOOM

–

6MNO

)

ROUTEM

AV OUT

VIEW

VOICE

OPEN

SUBTITLE

MAP DIR

ꢁꢂ

ꢃ

ANGLE

English

Remote Controller

ROUTEM

Displays Route Option menu.

NAVI (NAVI mode)

•

[RC-DV330]

[—]

ENTER

•

NAVI

AUDIO RETURN

Joystick

MODE/TOP MENU FNC/MENU/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

SUBTITLE

ANGLE

Scrolls the map, or moves the cursor.

MAP DIR

ZOOM

OUT

ꢃ

ꢁꢂ

POSITION

AUD

•

DVD

VIEW

Switches between 2D and 3D map displays.

ENTER

NAVI

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

SUBTITLE

MAP DIR

ENTER

ANGLE

ZOOM

ꢄ

Performs the selected function.

VOL

ꢃ

ꢁꢂ

OUT

POSITION

VOICE

Plays Voice guidance.

AUD

•

DVD

ENTER

NAVI

•

ENTER

•

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

•

NAVI

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

ZOOM

SUBTITLE

MAP DIR

Zooms in or out the navigation map.

ANGLE

DISP

MAP DIR

SRC

V.SEL

ZOOM

OUT

ꢃ

ꢁꢂ

POSITION

Switches between the heading up navigation and

AUD

•

north up navigation map displays.

DVD

ENTER

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

SUBTITLE

MAP DIR

Displays Main menu.

ANGLE

ZOOM

ꢄ

VOL

DISP

SRC

V.SEL

ZOOM

OUT

ꢃ

ꢁꢂ

POSITION

AUD

•

DVD

ENTER

CANCEL

Displays previous screen.

•

ENTER

•

NAVI

AUDIO RETURN

MODE/TOP MENU FNC/MENU/PBC

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

SUBTITLE

MAP DIR

ANGLE

POSITION

Displays the current position.

DISP

SRC

V.SEL

ZOOM

OUT

ꢃ

ꢁꢂ

POSITION

AUD

•

DVD

ENTER

DNX7120/DDX712/DDX7032

TV (TV mode)

[RC-DV330]

[RC-DV340]

Switching Band/Video

It switches between the station of the TV band to

receive and video input.

ROUTEM

AV OUT

VIEW

VOICE

OPEN

CANCEL

SUBTITLE

ANGLE

ZOOM

MAP DIR

AM−

OPEN

VOL

ꢄ

ꢅ

ꢄ

VOL

2ZONE

2^ABC3DEF

−

ꢆ

ꢅ

2ZONE

Channel Selection

The TV channel to receive is selected.

VIEW

MAP DIR

ANGLE

ZOOM

AM−

OPEN

ꢄ

VOL

ꢄ

ꢅ

−

ꢅ

2ZONE

2^ABC3DEF

ꢆ

Direct tuning

(NTSC TV type only)

R.VOL

PQRS 8^TUV9WXYZ

ꢀ

PQRS 8^TUV9WXYZ

ꢀ

CLEAR

DIRECT

ATT

CLEAR

DIRECT

ATT

Press this key first, and then specify the station to

receive with the numeric keypad.

Example: In case of Channel 6 (2-digit)

6MNO

Numeric keypad

2ZONE

ꢅ

2^ABC3DEF

2ZONE

2^ABC3DEF

ꢆ

ꢁ

R.VOL

ꢀ

4GHI 5JKL 6MNO

ꢁ

R.VOL

ꢀ

4GHI 5JKL 6MNO

PQRS 8^TUV9WXYZ

7PQRS 8^TUV9WXYZ

CLEAR

DIRECT

ATT

CLEAR

DIRECT

ATT

•

The number of the memorized station is

selected. (

–

6MNO

)

Press the direct tuning key first, then specify the

channel of the station to receive.

English

DVD Language Codes

Code

Language

Afar

Abkhazian

Afrikaans

Amharic

Arabic

Assamese

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bislama

Bengali, Bangla

Tibetan

Breton

Catalan

Corsican

Czech

Code

Language

Icelandic

Italian

Japanese

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean

Kashmiri

Kurdish

Kirghiz

Latin

Luxembourgish

Lingala

Laotian

Lithuanian

Latvian, Lettish

Malagasy

Maori

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay

Maltese

Burmese

Nauru

Nepali

Dutch

Norwegian

Occitan

(Afan) Oromo

Oriya

Punjabi

Code

Language

Singhalese

Slovak

Slovenian

Samoan

Shona

Somali

Albanian

Serbian

Siswati

Sesotho

Sundanese

Swedish

Swahili

Tamil

Telugu

Tajik

Thai

Tigrinya

Turkmen

Tagalog

Setswana

Tongan

Turkish

Tsonga

Tatar

Welsh

Danish

German

Bhutani

Greek

English

Esperanto

Spanish

Estonian

Basque

Persian

Finnish

Fiji

Faroese

French

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Twi

Ukrainian

Urdu

Uzbek

Vietnamese

Volapuk

Wolof

Xhosa

Yoruba

Chinese

Zulu

gli

Polish

Pashto, Pushto

Portuguese

Quechua

Rhaeto-Romance

Kirundi

Romanian

Russian

Kinyarwanda

Sanskrit

Hebrew

Hindi

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

Indonesian

Sindhi

Sangho

Serbo-Croatian

DNX7120/DDX712/DDX7032

Help?

Troubleshooting

Tuner source

Some functions of this unit may be disabled by

some settings made on this unit.

Radio reception is poor.

✔

The car antenna is not extended.

Pull the antenna out all the way.

• Cannot set up the subwoofer.

• Cannot set up subwoofer phase.

• No output from the subwoofer.

• Cannot set up the low pass filter.

• Cannot set up the high pass filter.

☞

✔

The antenna control wire is not connected.

☞

Connect the wire correctly, referring to the

section on <INSTALLATION MANUAL>.

Subwoofer is not set to On. ☞ <Audio Setup>

(page 62)

Disc source

The Dual zone function is enabled. ☞ <Zone

Control> (page 88)

The specified disc does not play, but another

one plays instead.

✔

The specified CD is quite dirty.

Clean the CD.

Cannot set up the subwoofer phase.

Subwoofer is not set to On. ☞ <Audio Setup>

(page 62)

☞

✔

The disc is loaded in a different slot from that

specified.

Eject the disc magazine and check the

number for the specified disc.

Low pass filter is set to Through. ☞ <Crossover

Network Setup> (page 63)

☞

✔

The disc is severely scratched.

Try another disc instead.

• Cannot select the output destination of the

subsource in the Dual zone.

• Cannot adjust the volume of the rear

speakers.

The Dual zone function is disabled. ☞ <Zone

Control> (page 88)

☞

Audio file source

The sound skips when an Audio file is being

played.

✔

The media is scratched or dirty.

Cannot play audio files.

"CD Read" of <System Setup> (page 66) is set

to "2".

☞

Clean the media, referring to the CD

cleaning of the section on <Handling discs>

(page 6).

Cannot Folder select.

The Scan play or Random play function is

enabled.

✔

The recording condition is bad.

Record the media again or use another

media.

☞

Cannot perform Repeat play.

The PBC function is enabled.

Navigation

The touch panel control of the navigation

system does not work.

• Cannot set up the equalizer.

• Cannot set up the crossover network.

The Dual zone function is enabled. ☞ <Zone

Control> (page 88)

✔

Navigation software is not the latest version.

☞

Update the navigation software. For how to

update the software, refer to the instruction

manual of the navigation unit.

What might seem to be a malfunction in your unit

may just be the result of slight misoperation or

miswiring. Before calling service, first check the

following table for possible problems.

General

The Touch Sensor Tone doesn’t sound.

✔

The preout jack is being used.

☞

The Touch Sensor Tone can’t be output from

the preout jack.

English

Help?

Error

Error 07–67:

When the unit fails to operate correctly, the

cause of the failure appears on the display.

The unit is not operating correctly due to some reason

or other.

Protect :

➡ Push the unit's Reset button. If the "Error 07−67"

message does not disappear, see your nearest

Kenwood dealer.

Protective circuit has been activated because a speaker

cord has shorted or it has come in contact with the car

chassis.

No Device (USB device)/Disconnected (iPod):

The USB device/iPod is selected as a source although

no USB device/iPod is connected.

➡ Change the source to any source other than

USB/iPod. Connect an USB device/iPod, and

change the source to USB/iPod again.

➡ Wire or insulate the speaker cord as appropriate

and then push the Reset button.

Hot Error :

When the internal temperature of this unit rises to 60°C

or more, the protection circuit is activated and you

may not be able to operate the unit. At such times this

message will appear.

No Music:

➡ Use the unit again after reducing the

temperature inside the vehicle.

The connected USB device contains no playable audio

file.

Media was played that doesn’t have data recorded that

the unit can play.

Hold Error :

Activation of the protective circuit when the

temperature inside the disc changer is higher than 60

degrees Celsius stops the disc changer from operating.

At such times this message will appear.

USB Device Error!!:

The connected USB device is rated a current capacity

higher than the allowable limit. .

➡ Use when the temperature at the site where the

disc changer has been fitted has dropped.

➡ Check the USB device.

Some trouble may have occurred to the connected

USB device.

➡ Change the source to any source other than USB.

Remove the USB device.

Mecha Error :

The disc player is malfunctioning.

➡ Eject the disc and try inserting it again. Contact

the Kenwood dealer if this indicator continues

blinking or the disc cannot be ejected.

Authorization Error:

Connection to the iPod has failed.

➡ Remove the iPod and then reconnect it.

The unit does not support the iPod.

➡ Refer to <iPod that can be connected to this

unit> (page 7).

Disc Error :

An unplayable disc is inserted.

Read Error :

Disc is quite dirty.

Update your iPod:

➡ Clean the disc, referring tot he section on

<Handling discs> (page 6).

Disc is upside down.

The iPod's software is an older version which the unit

can not support.

➡ Confirm that the software for the iPod is the

latest version. Refer to <iPod that can be

connected to this unit> (page 7).

➡ Load the disc with the labeled side up.

Region code Error :

The disc you wanted to play has a region code that

cannot be played with this unit.

Update your USB database:

The USB device is different from the previous one or

the contained audio files are replaced.

➡ Update your database. Refer to <Function wihle

display the Control Screen> of USB Device

Control (page 36).

Parental level Error:

The disc you wanted to play has a higher level than the

parental level you set.

DNX7120/DDX712/DDX7032

Check Sirius:

CH UNAUTHORIZED:

The unit cannot recognize the connected Sirius Tuner

Box.

➡ Check the connection of the Sirius Tuner Box.

The selected channel is not subscribed.

OFF AIR:

The broadcast of the selected channel has finished.

Antenna Error:

Something is wrong with the anntena.

➡ Check the connection of the antenna.

Acquring Signal:

The unit cannot receive any signal.

➡ Move the vehicle to the area where the unit can

receive signal.

Updating Firmware:

Updating the firmware of Sirius tuner.

➡ Operation is invalid until the update is

completed.

Updating Channels **% Completed:

Updating the Sirius Channel Map.

➡ Operation is invalid until the update is

completed.

Subscription Updated:

Updating the suscription information.

➡ Operation is invalid until the update is

completed.

Invalid Channel:

The selected channel is invalid.

➡ Select a different channel.

Call 888-539-SIRIUS to Subscribe:

The selected channel is not subscribed.

➡ Call the displayed number for subscription.

CHECK XM TUNER:

The unit cannot recognize the connected XM Tuner.

➡ Check the connection of the XM Tuner.

NO SIGNAL:

The unit cannot receive any signal.

➡ Check the connection of the antenna.

CHECK ANTENNA:

Something is wrong with the anntena.

➡ Check the connection of the antenna.

CH UNAVAILABLE:

The selected channel is invalid.

➡ Select a different channel.

English

Specifications

Monitor section

USB interface section

Picture Size

USB Standard

: 6.95 inches (diagonal) wide

: 156.2 mm (W) x 82.4 mm (H)

: USB 1.1/ 2.0

File Sytem

Display Sytem

: FAT 16/ 32

: Transparent TN LCD panel

Maximum Power Supply Current

Drive System

: 500 mA

: TFT active matrix system

D/A Converter

Number of Pixels

: 24 Bit

: 336,960 (480H x 234V x RGB)

Audio Decoder

Effective Pixels

: MP3/ WMA/ AAC

: 99.99 %

Pixel Arrangement

: RGB striped arrangement

Back Lighting

: Cold Cathode Fluorescent Tube

FM tuner section

Frequency Range (200 kHz)

: 87.9 MHz – 107.9 MHz

Usable Sensitivity (S/N : 30 dB)

: 9.3 dBf (0.8 μV/ 75 Ω)

Quieting Sensitivity (S/N : 50 dB)

DVD player section

D/A Converter

: 15.2 dBf (1.6 μV/ 75 Ω)

: 24 bit

Frequency Response ( 3.0 dB)

Audio Decoder

: 30 Hz – 15 kHz

: Linear PCM/ Dolby Digital/ dts/ MP3/ WMA/ AAC

S/N Ratio (dB)

Video Decoder

: 70 dB (MONO)

: MPEG1/ MPEG2/ MPEG4 (DivX)

Selectivity ( 400 kHz)

Wow & Flutter

: ≥ 80 dB

: Below Measurable Limit

Stereo Separation

Frequency Response

: 40 dB (1 kHz)

Sampling frequency; 96 kHz : 20 – 44,000 Hz

Sampling frequency; 48 kHz : 20 – 22,000 Hz

Sampling frequency; 44.1 kHz : 20 – 20,000 Hz

Total Harmonic Distortion

: 0.008 % (1 kHz)

AM tuner section

Frequency Range (10 kHz)

: 530 kHz – 1700 kHz

Usable Sensitivity

: 28 dBμ

S/N Ratio (dB)

: 98 dB (DVD-Video 96 kHz)

Dynamic Range

: 98 dB (DVD-Video 96 kHz)

Disc Format

: DVD-Video/ VIDEO-CD/ CD-DA

Sampling Frequency

: 44.1/ 48/ 96 kHz

Quantifying Bit Number

: 16/ 20/ 24 bit

100

DNX7120/DDX712/DDX7032

Video section

Navigation section (DNX7120 only)

Color System of External Video Input

Receiver

: NTSC

: High-sensitivity GPS receiver

External Video Input Level (mini jack)

Reception Frequency

: 1 Vp-p/ 75 Ω

: 1575.42 MHz (C/A code)

External Audio Max Input Level (mini jack)

Acquisition Times

: 2 V/ 25 kΩ

Cold : < 38 seconds

Factory Reset : < 45 seconds

(On average for a stationary receiver with a clear

view of the sky)

Video Output Level (RCA jacks)

: 1 Vp-p/ 75 Ω

Audio Output Level (RCA jacks)

: 1.2 V/ 10 kΩ

Accuracy

Position : < 10 meters typical

Velocity : 0.05 m/sec. RMS

Position Method

Analog RGB input (DDX712/DDX7032 only)

: 0.7 Vp-p/ 75 Ω

: GPS

Antenna

: External GPS antenna

Audio section

Maximum Power (Front & Rear)

: 50 W x 4

Full Bandwidth Power (Front & Rear)

(4 Ω, 14.4 V, 1 % THD)

: 22 W x 4

Preout Level (V)

: 2 V/ 10 kΩ

General

Operating voltage

: 14.4 V (11 – 16 V allowable)

Current Consumption

: 15 A

Preout Impedance

: ≤600 Ω

DImensions (W × H × D)

: 182 × 112 × 163 mm

7-3/16 x 4-7/16 x 6-7/16 inch

Operational Temperature Range

: -10 °C – +60 °C

Speaker Impedance

: 4 – 8 Ω

Tone action

Bass : 100 Hz 8 dB

Middle : 1 kHz 8 dB

Treble : 10 kHz 8 dB

Storage Temperature Range

: -20 °C – +85 °C

Weight (DNX7120)

: 2.5 kg (5.5 lbs)

Weight (DDX712/DDX7032)

: 2.45 kg (5.4 lbs)

External SW

Maximum Power Supply Current

: 500 mA

Specifications subject to change without notice.

Although the effective pixels for the liquid crystal panel is given as 99.99% or more, 0.01% of pixels may not light or may light

incorrectly.

English

101

2CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation

exposure.

In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product

safety.

Kenwood Corporation

2967-3, ISHIKAWA-MACHI,

HACHIOJI-SHI

TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS N0.21 CFR

1040. 10, CHAPTER 1, SUBCHAPTER J.

Location : Bottom Panel

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful

interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to

operate this equipment if an unauthorized change or modification is made.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the

instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

About DivX

DivX is a popular media technology created by DivX, Inc. DivX media Files contain highly compressed video

with high visual quality that maintains a relatively small file size. DivX files can also include advanced media

features like menus, subtitles, and alternate audio tracks. Many DivX media files are available for download

online, and you can create your own using your personal content and easy-to-use tools from DivX.com.

About DivX Certified

DivX Certified products are officially tested by the creators of DivX and guaranteed to play all versions of DivX

video, including DivX 6. Certified products qualify for one of several DivX Profiles that designate the type of

video the product supports, from compact portable video to high-definition video.

The "AAC" logo is trademark of Dolby Laboratories.

Apple, the Apple logo, and iPod are trademarks of Apple Inc., registered in the U.S. and other countries.

is a trademark of DVD Format/Logo Licensing Corporation registered in the U.S., Japan and other countries.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property

rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other

limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Manufactured under license from Dolby Laboratories.

"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and

worldwide patents issued & pending. DTS and DTS 2.0 + Digital Out are registered trademarks and the DTS logos and Symbol

Pyramid Car Audio Car Amplifier Pyramid America Series amplifier User Manual
Pioneer Premier DEH P350 User Manual
Pioneer DEQ P7650 User Manual
Pelco Camera Lens C2403M C User Manual
Panasonic VARIABLE FRAME RATE AJ HDC27H User Manual
Panasonic HDC SD20PC User Manual
LG Electronics GBW H20N User Manual
Kenwood KRC 365L User Manual
Kenwood Car Stereo System KDC M4524G User Manual
JVC LYT1265 001A User Manual