Kenwood DDX7025 User Manual

DDX7025

MONITOR WITH DVD RECEIVER

INSTRUCTION MANUAL

TV Setup ..........................................................70

• Displaying the TV1 Area Set Up screen

• Displaying the TV2 Area Set Up screen

RDS Setup ........................................................71

• Displaying the RDS Set Up 1 screen

• Displaying the RDS Set Up 2 screen

DAB Set Up ......................................................72

• Displaying the DAB Set Up screen

• Announcement Selection

AMP Control ....................................................74

• Displaying the AMP Control screen

Sound Effects Menu

Sound Effects Menu ........................................76

• Displaying the Control screen

• Displaying the Sound Effects Menu screen

Audio Control ..................................................77

• Displaying the Audio Control 1 screen

• Displaying the Audio Control 2 screen

Equalizer ..........................................................78

• Displaying the Equalizer screen

• Tone curve setup

• Parametric Equalizer

Zone Control ....................................................82

• Displaying the Zone Control screen

Digital Effect ....................................................83

• Displaying the Digital Effect screen

Position ..............................................................84

• Displaying the Position screen

Hands-Free Unit Control......................................86

GSM control ....................................................86

• Displaying the Control screen

• When called

• When dialing

• Calling by Phone Book

• Addition to Phone Book

• Editing the Phone Book

• Quick Dialing

• Hands Free Setup

• Reading the SMS (Short Message Service)

messages

• Creating an SMS (Short Message Service)

message

Glossary ................................................................94

Troubleshooting Guide........................................95

Specifications ..................................................100

English 3

Before Use

Audio units you can control from the

2WARNING

DDX7025 Receiver (in November of 2003):

To prevent injury and/or fire, take the following

precautions:

• Ensure that the unit is securely installed. Otherwise it

may fly out of place during collisions and other jolts.

• When extending the ignition, battery or ground wires,

make sure to use automotive-grade wires or other wires

KDC-CPS89, KDC-CPS87, KDC-CPS85, KDC-C719,

KDC-C717, KDC-C715, KDC-C669, KDC-C667, KDC-C665,

KDC-C469, KDC-C467, KDC-C465, KDC-D301, KMD-D401,

KTC-9090DAB, KDV-C820, KDC-C719MP, KCA-HF521,

KPA-CP100, KTC-V500N/P/E (Set the "O-N" switch to "N"

position if provided.)

with an area of 0.75mm (AWG18) or more to prevent

cable deterioration and damage to the cable coating.

Navigation units you can control from the

DDX7025 Receiver (in November of 2003):

KNA-DV3200, KNA-DV2200

• To prevent short circuits, never put or leave any metallic

objects (e.g., coins or metal tools) inside the unit.

• If the unit starts to emit smoke or strange smells, turn

off the power immediately and consult your Kenwood

dealer.

• Do not touch the liquid crystal fluid if the LCD is

damaged or broken due to shock. The liquid crystal fluid

may be dangerous to your health or even fatal.

If the liquid crystal fluid from the LCD contacts your body

or clothing, wash it off with soap immediately.

Loading and Replacing the battery

Use one lithium battery

(CR2025).

Insert the batteries with

the + and - poles aligned

properly, following the

Keep on slide

illustration inside the case.

Pull out

2CAUTION

2WARNING

To prevent damage to the machine, take the

following precautions:

• Make sure to ground the unit to a negative 12V DC

power supply.

Store unused batteries out of the reach of children. Contact

a doctor immediately if the battery is accidentally

swallowed.

Do not set the remote on hot places such as above the

dashboard.

• Do not open the top or bottom covers of the unit.

• Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

• Do not subject the faceplate to excessive shock, as it is

a piece of precision equipment.

• The provided batteries are intended for use in operation

checking, and their service life may be short.

• When the remote controllable distance becomes short,

replace both of the batteries with new ones.

• When replacing a fuse, only use a new one with the

prescribed rating. Using a fuse with the wrong rating

may cause your unit to malfunction.

• To prevent short circuits when replacing a fuse, first

disconnect the wiring harness.

• Do not use any screws except for the ones provided.

The use of improper screws might result in damage to

the main unit.

• You cannot view video pictures whilst the vehicle is

moving. To enjoy TV/video pictures, find a safe place to

park and engage the parking brake.

Cleaning the panel and monitor

When the operator panel and monitor panels are dirty, wipe

and clean them using a soft cloth (such as a commercially

available silicon coated cloth). When contaminated

excessively, clean them using a cloth dipped in a neutral

detergent first, then remove the detergent using a dry cloth.

Do not use a hard cloth and a volatile chemical (such as an

alcohol). If used, the panel surface may be scratched or

printed letters may be erased.

Cleaning the disc slot

As dust can accumulate in the disc slot, clean it

occasionally. Your discs can get scratched if you put them

in a dusty disc slot.

NOTE

• If you experience problems during installation, consult

your Kenwood dealer.

• If the unit does not seem to be working right, try

pressing the reset button first. If that does not solve the

problem, consult your Kenwood dealer.

Lens Fogging

Right after you turn on the car heater in cold weather, dew

or condensation may form on the lens in the disc player of

the unit. Called lens fogging, discs may be impossible to

play. In such a situation, remove the disc and wait for the

condensation to evaporate. If the unit still does not operate

normally after a whilst, consult your Kenwood dealer.

This Product is not installed by the manufacturer of a

vehicle on the production line, nor by the professional

importer of a vehicle into an EU Member State.

Reset button

Screen brightness during low temperatures

When the temperature of the unit falls such as during

winter, the liquid crystal panel's screen will become darker

than usual. Normal brightness will return after using the

monitor for a whilst.

4 English

Region codes in the world

The DVD players are given a region code according to the country or area it is marketed, as shown in the following map.

Icons on the DVD discs

Icon

Description

Indicates the region code where the disc can be played.

Number of voice languages recorded with the audio function. The number in the icon indicates the number

of voice languages. (Max. 8 languages)

Number of subtitle languages recorded with the subtitle function. The number in the icon indicates the

number of subtitle languages. (Max. 32 languages)

Number of angles provided by the angle function. The number in the icon indicates the number of angles.

(Max. 9 angles)

Aspect ratios that can be selected. "LB" stands for Letter Box and "PS" for Pan/Scan. In the example on the

left, the 16:9 video can be converted into letter box video.

16:9 LB

Unplayable discs

This player cannot play back any of the following discs.

• DVD-ROM/DVD-RAM discs

• HQ-VCD discs

• CDV discs (Only the audio part can be reproduced)

• Photo CD discs

• CD-G/CD-EG/CD-EXTRA discs (Only the audio can be reproduced)

• DVD-Audio

Also, you cannot play back the DVD-R/RW and DVD+R/RW discs if not recorded in the DVD-Video format.

Restrictions due to difference between discs

Explanation of icons used on this manual

Some DVD and VCD discs can be played only in

certain playback modes according to the intentions

of the software producers. As this player plays

discs according to their intentions, some functions

may not work as intended by you. Please be sure

to read the instructions provided with each disc.

When an inhibition icon is displayed on the

Inhibition

icon

Indicates the key operation on the receiver.

Indicates the button you must touch.

Indicates the key or joystick operation on the remote

controller.

monitor, it indicates that the disc being played is

under the restriction as described above.

The initial value of each setup is shown.

The illustrations of the display and the panel appearing in this

manual are examples used to explain more clearly how the

controls are used. Therefore, what appears on the display in the

illustrations may differ from what appears on the display on the

actual equipment, and some of the illustrations on the display

may represent something impossible in actual operation.

Gives an additional information or an operation advice.

Time is displayed on each control screen in the 12 hour clock display type (with AM/PM displayed) or in the 24 hour clock display type

(without AM/PM displayed) depending on the sales area. The display type cannot be changed. In this instruction manual, screens of the

24 hour display type are used as examples.

English 5

About discs

Handling discs

Removing discs

• Don’t touch the recording surface of the disc.

When removing discs from this unit pull them out

horizontally.

Discs that can’t be used

• Discs that aren’t round can’t be used.

• CD-R/RW, DVD-R/RW, and DVD+R/RW are easier to

damage than a normal music CD. Use a CD-R/RW, DVD-

R/RW, or DVD+R/RW after reading the caution items on

the package etc.

• Don’t stick tape etc. on the disc.

Also, don’t use a disc with tape stuck on it.

• Discs with coloring on the recording surface or that are

dirty can’t be used.

• This unit can only play the CDs with

It may not correctly play discs which do not have the

mark.

• A CD-R or CD-RW that hasn’t been finalized can’t be

played. (For the finalization process refer to your CD-

R/CD-RW writing software, and your CD-R/CD-RW

recorder instruction manual.)

When using a new disc

If the disc center hole or outside rim has burrs, use it after

removing them with a ball pen etc.

Burrs

Disc storage

• Don’t place them in direct sunlight (On the seat or

dashboard etc.) and where the temperature is high.

• Store discs in their cases.

Burrs

Disc accessories

Don’t use disc type accessories.

Disc cleaning

Clean from the center of the disc and move outward.

6 English

Notes on playing MP3/WMA

This unit can play MP3 (MPEG1 Audio Layer 3)/WMA.

Note, however, that the MP3/WMA recording media

and formats acceptable are limited. When writing

MP3/WMA, pay attention to the following restrictions.

Entering file and folder names

The code list characters are the only file names and folder

names that can be entered and displayed.

If you use any other character for entry, the file and folder

names are not displayed correctly. They may neither be

displayed correctly depending on the CD writer used.

The unit recognizes and plays only those MP3/WMA which

have the MP3/WMA extension (.MP3/.WMA).

Acceptable media

The MP3/WMA recording media acceptable to this unit are

CD-ROM, CD-R, and CD-RW.

When using CD-RW, do full format not quick format to

prevent malfunction.

A file with a name entered with characters not on the code

list may not play correctly.

Writing files into a medium

Acceptable medium formats

When a medium containing MP3/WMA data is loaded, the

unit checks all the data on the medium. If the medium

contains a lot of folders or non-MP3/WMA files, therefore,

it takes a long time until the unit starts playing MP3/WMA.

In addition, it may take time for the unit to move to the

next MP3/WMA file or a File Search or Folder Search may

not be performed smoothly.

The following formats are available for the media used in

this unit. The maximum number of characters used for file

name including the delimiter (".") and three-character

extension are indicated in parentheses.

• ISO 9660 Level 1 (12 characters)

• ISO 9660 Level 2 (31 characters)

• Joliet (64 characters)

Loading such a medium may produce loud noise to damage

the speakers.

• Romeo (128 characters)

• Do no attempt to play a medium containing a non-

MP3/WMA file with the MP3/WMA extension.

The unit mistakes non-MP3/WMA files for MP3/WMA data

as long as they have the MP3/WMA extension.

Up to 170 characters can be displayed in the long file name

format. For a list of available characters, see the instruction

manual of the writing software and the section Entering file

and folder names below.

The media reproducible on this unit has the following

limitations:

• Do not attempt to play a medium containing non

MP3/WMA.

• Maximum number of directory levels: 8

• Maximum number of files per folder: 255

• Maximum number of characters for folder name: 64

• Maximum number of folders: 100

MP3/WMA written in the formats other than the above

may not be successfully played and their file names or

folder names are not properly displayed.

MP3/WMA playing order

When selected for play, Folder Search, File Search, or for

Folder Select, files and folders are accessed in the order in

which they were written by the CD writer.

Because of this, the order in which they are expected to be

played may not match the order in which they are actually

played. You may be able to set the order in which

MP3/WMA are to be played by writing them onto a

medium such as a CD-R with their file names beginning

with play sequence numbers such as "01" to "99",

depending on your CD writer.

Settings for your MP3/WMA encoder and CD

writer

Do the following setting when compressing audio data in

MP3/WMA data with the MP3/WMA encoder.

• Transfer bit rate: MP3: 8 —320 kbps

WMA: 48 —192 kbps

• Sampling frequency: MP3: 32, 44.1, 48 kHz

WMA: 32, 44.1, 48 kHz

When you use your CD writer to record MP3 up to the

maximum disc capacity, disable additional writing. For

recording on an empty disc up to the maximum capacity at

once, check Disc at Once.

Play mode may not be possible when portions of the

functions of Windows Media Player 9 or higher are used.

Entering ID3 tag

The Displayable ID3 tag is ID3 version 1.x.

For the character code, refer to the List of Codes.

English 7

DDX7025 Basic operations

8 English

Play Disc

[Disc insertion slot]

Track/Station Selectors

[SEEK] key

A disc is played when you insert it.

Selects a music or chapter, track, or frequency.

Play/Pause

Attenuator/Loudness

[ATT]/[LOUD] key

[

] key

Pauses and replays a disc.

Attenuates the volume.

Press it again to cancel muting.

Press it for more than one second to turn the Loudness

function on or off. (see page 77)

If turned on, high and low tones are enhanced during

low volume.

Eject Disc

[EJECT] key

The disc is ejected.

Switch Video Sources

[V.SEL] key

Traffic Information

[TI] key

The video sources are switched each time you press

the key.

Turns the Traffic Information function On or Off. (see

page 24)

Screen Setup

[SCRN] key

Displays the Screen Control or Tilt Control screen. (see

page 46)

Function

[FNC] key

* Optional accessory

Clears the video image when pressed more than one

second. When pressed again, the original image is

redisplayed.

The video sources are switched each time you press

the key.

Switch Audio Source/Power Supply

[SRC] key

The audio sources are switched each time you press

the key.

Switches the source that is output at the AV OUTPUT

terminal when it is pressed more than 1 second.

Switch Screen Mode/GSM

[MODE]/[GSM] key

The screen mode is switched. (see page 12)

The GSM Control screen appears when you hold down

the key more than 1 second.

* Optional accessory

Hold down more than 1 second to turn the power

supply Off.

Push it again to turn power supply On.

Volume Controls

[VOL] key

The display turns on when you put the parking brake,

except for the navigation system.

English 9

Basic Operations of Remote Controller

Remote Control Mode selector

[DISC]

Selects one of the following remote control modes.

TV: TV source

DVD: Built-in DVD/VCD/CD/MP3/WMA player source

AUD: Tuner source or attached disc changer/disc

player source

Stops to play the built-in disc player.

Switches over the sound source each time it is

pressed.

Selects the Direct Search mode.

(see page 19/24/33 for <Direct Search>)

Volume Control

Adjusts the volume.

10 English

Joystick

[DVD]

[DISC]

Select a folder or a disc.

Enters your selection from the DVD Disc Menu.

[TV]

[DVD] [VCD]

FM: Switches to TV1, TV2, or VIDEO.

Returns to the previous screen when the DVD/VCD

Disc Menu is used.

[TUNER]

FM: Switches to the FM1, FM2, or FM3 band.

AM: Switches to the AM band.

[DVD]

Calls the Top menu of DVD Disc Menu.

[DISC]

Switch Video Sources

[V.SEL] key (When is set to "TV")

Selects a chapter, a track or a song.

[TV]

The video sources are switched each time you press

the key.

Select a channel.

[TUNER]

Selects a station.

[DVD]

1 : Fast Backward (Rewind). The speed changes

each time it is pressed.

¡ : Fast Forward. The speed changes each time it is

* Optional accessory

pressed.

[DVD]

[TV] [TUNER]

Calls the DVD Disc Menu.

—

Call the stations from memory.

[DVD]

[DISC]

Each time you press the button, the angle switches.

Plays or pauses.

[DVD] [VCD]

[TUNER]

Each time you press the button, the zoom ratio

switches.

Selects the Seek mode. (see page 22/40 for the <Seek

Mode>)

[DVD]

;

Switches a subtitle language.

Slow Backward.

: Slow Forward.

[DVD]

Switches an audio language.

Attenuator

[ATT] key

Attenuates the volume.

Press it again to cancel muting.

[DVD]

[VCD]

[DISC]

[TV]

: An operation during DVD playback

: An operation during VCD playback

: An operation during DVD, VCD, CD, MP3/WMA or MD playback

: An operation during TV source

[TUNER]

: An operation during FM/AM broadcasting source

English 11

Switch Screen Mode

The Screen mode of the monitor changes each time the [MODE] key is pressed.

[MODE] key

Full picture mode [FULL]

Justify picture mode [JUST]

Cinema picture mode [CINEMA]

Zoom picture mode [ZOOM]

Normal picture mode [NORMAL]

• When the Menu, Easy Control screen, or Navigation is selected, it is shown in the full-size display mode automatically.

Their Screen mode cannot be changed.

• The Screen mode can be set for each of DVD/VCD, TV, and video images.

12 English

English 13

Control during DVD Video or Video CD Playback

Various control screens appear when you play back a DVD Video (DVD) or a Video

Displaying the DVD/VCD

Playback screen

You can use the following operations when displaying

DVD/VCD images.

Title Number Display

Chapter Number Display

Play Time Display

Plays back the

DVD or VCD.

Forward Chapter Search Area

Selects the next chapter.

Backward Chapter Search Area

Selects the previous chapter.

DVD playback screen

DVD VIDEO

Title 1 Chap 3

0:02:37

DVD Disc Menu Control Buttons Area

Displays the Disc Menu Control buttons (see page

18).

MODE: FU L L AV-OUT: AV - I N

Information Display Button Area (see page 19)

DVD VIDEO

Title 1 Chap 3

0:02:37

VCD playback screen

Scene/Track Number Display

MODE: FU L L AV-OUT: AV - I N

DVD VCD

PBC

Scene 255

2:37

VER2

Forward Scene/Track Search Area

Selects the next scene (when PBC is On) or track

(when PBC is Off).

Backward Scene/Track Search Area

Selects the previous scene (when PBC is On) or

track (when PBC is Off).

Zoom Control Button Area

Displays the Zoom Control buttons (see page 19).

DVD VCD

Scene 255

2:37

Information Display Button Area (see page 19)

• For DVD/VCD playback, DVD/VCD picture

selection, or controller key operations, see

<DDX7025 Basic Operations> (see page 8).

• The information display is cleared automatically

after approximately 5 seconds. Also, the

information can be displayed automatically when

it is updated (see page 65).

14 English

CD (VCD) disc.

Displaying the Easy Control

Panel

The Control Panel is displayed in a floating position of the

DVD/VCD screen.

Switches the source.

Stops to play.

Rewinds or fast forwards.

Chapter Search (DVD)

Searches for a chapter.

Scene/Track Search (VCD)

Selects a scene (when PBC is On) or a track (when

PBC is Off).

Display the Easy Control Panel

T i t l e

MODE: FU L L AV-OUT: AV - I N

C h a p

0 : 0 5 : 3 2

DVD VIDEO

Plays or pauses.

The Easy Control Panel display is cleared when you

touch the center of image display area.

SRC

DVD VIDEO

T i t l e

C h a p

0 : 0 5 : 3 2

English 15

Control during DVD Video or Video CD Playback

Displaying the DVD/VCD

Control screen

Ejects the disc from the built-in disc player.

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu. (see page 47)

Displays the Source Select screen. (see page 45)

Fast Forwards or Rewinds.

;

Plays a DVD/VCD using various functions.

DVD/VCD Control screen

Stops to play.

DVD V I DEO

When pressed twice, the disc is played from its

beginning when you play it in the next time.

1 3 : 5 0

Audio

Set Up

Selects a chapter, a scene or a track.

When the DVD is paused, touch this button to start

single-frame stepping.

Direct

SRC

SCRL²⁹

PBC²⁷REP²⁸

Title Chap

KENWOOD

TIME

Plays or pauses.

T0:05:20

Slow Forwards or Backwards. (during DVD playback

only)

T-REP

Turns the PBC function of VCD On or Off. (when

VCD Ver 2.0 or SVCD is in use only)

Switches the Repeat Play operations in the

following sequence.

DVD: Title Repeat, Chapter Repeat, Repeat Off

VCD: Track Repeat, Repeat Off (Available when the

PBC is off)

Scrolls the display text.

Switches the play time display in the following

sequence.

DVD: Title, chapter, remaining titles

VCD: Track, disc, remaining discs (Effective only

when the PBC function is off)

Title Number Display (DVD)

Chapter/Scene/Track Number Display

Play Time Display

Appears when a disc is inserted.

Function Indicator

16 English

English 17

Control during DVD Video or Video CD Playback

DVD Disc Menu

Select Disc Menu options

Disc Menu

Selects an option from the DVD Disc Menu.

Displays the Disc Menu Control screen

C t r l

DVD Disc Menu Control Buttons

Area (page 14)

R e t u r n

C t r l

Top

Audio

1 / 1

C t r l

SUB

1 0 / 1 0

C a n c e l

E n t e r

E x i t

Zoom

A n g l e 1 / 1

E x i t

Calls the Menu.

Returns to the Disc Menu Control screen.

Selects a menu option.

Calls the Menu Control.

Switches the picture angle.

Enters your menu selection.

Returns to the previous menu screen.

Displays the Top Menu.

(during program playback only)

Switches the caption language.

(during program playback only)

Switches the voice language.

(during program playback only)

Displays the Zoom Control screen.

Clears the Disc Menu Control.

Zoom Control

Zoom

Zoom^{C t r l}

C a n c e l

Zoom

O f f

E x i t

Changes the zoom ratio at 4 levels (2 times, 3

times, 4 times, or off) each time you touch.

Scrolls the screen in the direction you touch.

Returns to the Disc Menu Control screen.

Clears the Disc Menu Control.

18 English

VCD Zoom Control

Direct Search

Displays an enlarged VCD screen.

You can search for a DVD/VCD chapter, scene

or track by entering its number.

Displays the Zoom Control screen

Selects the Direct Search mode

Zoom Control Button Area

(page 14)

Zoom^{C t r l}

The following items can be searched directly each

time it is pressed.

DVD: Title, Chapter, Time, Direct number

VCD (when PBC is On): Scene, Direct number

VCD (when PBC is Off): Track, Time

However, the direct search may not be supported for

some discs.

Zoom O f f

E x i t

Enter a number or time

Changes the zoom ratio at 4 levels (2 times, 3

times, 4 times, or off) each time you touch.

Scrolls the screen in the direction you touch.

Clears the Zoom Control button.

—

Information Display

Displays the DVD and AV information.

The operation ends automatically if you do not

operate within 10 seconds.

Information Display Button Area

(Page 14)

The information is displayed for 5 seconds.

English 19

Tuner Control

Various control screens appear in the Tuner Source mode.

Displaying the Easy Control

Panel

The Tuner Control Panel is displayed in a floating position

of the selected picture.

Switches the source.

Switches the band (to AM or FM1/2/3).

Tunes in a station

Switches the Seek mode.

(see page 22 for the <Seek Mode>)

Displaying the Easy Control Panel

• For receiver key operations, see <DDX7025 Basic

Operations> (see page 8).

• The Easy Control Panel display is cleared when

you touch the center of image display area.

MODE: FU L L AV-OUT: AV - I N

SRC

TUNER

A M F M

P r e s e t

SEEK

9 8 . 1 M H z

F M 1

20 English

Displaying the Tuner Control

screen

Calls the Tuner Menu.

You can tune in a station using various functions.

Calls the Sound Effects Menu. (see page 76)

Displays the Source Select screen. (see page 45)

Calls the Setup Menu. (see page 47)

Switches to the FM1/2/3 band.

Tuner Control screen

Switches to the AM band.

Tunes in a station.

Use the <Seek Mode> to change the frequency

switching.

TUNER

1 3 : 5 0

Audio

Set Up

Direct

SRC

Switches between

buttons and

Function buttons to use.

LO.S ¹³AME SEEK DISP SCRL MONO

Turns the Local seek function On or Off.

FM1

Preset

98. 1 MHz

Selects the Auto Memory mode.

AUTO 1

(See page 22 for the <Auto Memory>)

Switches the Seek mode.

(see page 22 for the <Seek Mode>)

Selects the Program Service Name or Radio Text

mode for text display. (Only when receiving the FM

broadcast)

Scrolls the display text.

Select the Monaural reception mode. (Only when

receiving the FM broadcast)

When

buttons appear, you can call

up the stations from memory.

For memory of broadcasting stations, see <Auto

Memory> (see page 22) or <Manual Memory> (see

page 23).

Seek Mode Indicator

;

Displaying the Tuner Menu

screen

Memory Number Display

Selects options from various function menus.

Returns to the Tuner Control screen.

You can select menu options using various functions.

The available functions vary depending on the

model used (the tuner specifications and the

broadcasting system that can be received).

Tuner Menu screen

P r e s e t Se l e c t

PTY Sea r c h

Rad i o T e x t

TUNER

Audio

Set Up

SRC

English 21

Tuner Control

Seek Mode

Auto Memory

Sets a station selection.

Stores stations with good reception in memory

automatically.

SEEK

Select a band you wish to store in memory

If SEEK is not shown, touch

The mode is switched each time you touch the

button.

Select the Auto Memory mode

Tunes in a station with good

reception automatically.

AUTO 1

AME

Tune in stations in memory one

after another.

If AME is not shown, touch

AUTO 2

Start Auto Memory

Switches to the next channel

manually.

MANUAL

Touch

Auto Memory terminates when 6 stations are stored

or when all stations are tuned in.

The operation ends automatically if you do not

operate within 10 seconds.

22 English

Manual Memory

Preset Select

Stores the current receiving station in memory.

Lists and tunes in stations in memory one after

the other.

Select a station you wish to store in memory

Call the Tuner Menu

Store in memory

Call the Preset Select Menu

—

P r e s e t Se l e c t

are not shown, touch

Continue to touch until the memory number appears.

TUN₄ER

FM3 1) 100. 5 MHz

Audio

FM3 2) 100. 5 MHz

FM3 3) 100. 5 MHz

FM3 4) 100. 5 MHz

FM3 5) 100. 5 MHz

FM3 6) 100. 5 MHz

Set Up

SRC

98.1

Tunes in the displayed station.

Switches the band of the displayed station list.

Band display.

Returns to the Tuner Menu.

English 23

Tuner Control

Direct Search

Traffic Information

Tunes in a station when its frequency is

entered.

When a traffic bulletin starts, any source is

switched to the traffic information and it is

displayed automatically.

Select a band

When the traffic bulletin starts...

The Traffic Information screen appears automatically.

Traffic Information screen

Selects the Direct Search mode

1 3 : 5 0

T U N E R

Audio

Set Up

Direct

SRC

Enter a frequency

Traffic Infomation

—

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu. (see page 47)

When you enter them, signal reception starts.

Example: When you receive FM 92.1 MHz

During reception of traffic information the

adjusted volume is automatically remembered,

and the next time it switches to traffic

information it's automatically the remembered

volume.

Example: When you receive AM 810 kHz

Please note that if DSP unit (optional accessory)

is connected, the volume will be preset by

The operation ends automatically if you do not

operate within 10 seconds.

pressing the

button for 2 seconds or more.

24 English

Search for Program Type

Radio Text

A program is tuned when you set its program

type.

You can display the radio text.

Call the Tuner Menu

Display the Radio Text

Call the PTY Search Menu

Rad i o T e x t

PTY Sea r c h

TUNER

Rad i o t e x t :

Audio

TUNER

A l l S p e e c h

Set Up

SRC

Audio

A l l M u s i c

Set Up

Direct

SRC

N e w s

C u r r e n t A f f a i r s

I n f o r m a t i o n

SRCH

98.1

Re t u r n

Not Found

Displays the Radio Text.

Returns to the Tuner Menu.

Selects a program type.

Scrolls the program type list.

Searches for the program type.

It is displayed when the Program Type is selected.

Returns to the Tuner Menu.

Select a program type

N e w s

etc.

Search for the program type

SRCH

English 25

CD/MP3/WMA/Disc Changer Play Control

You can call various control screens during CD/MP3/WMA/Disc Changer playback.

Displaying the Easy Control

Panel

The CD/MP3/WMA/Disc Changer Play Control Panel is

displayed in a floating position of the selected picture.

Switches the source.

Stops to play the built-in disc player.

When a CD is played back on the built-in disc player:

Rewinds or fast forwards.

Selects a song.

Plays or pauses.

Display the Easy Control Panel

During CD playback

When an MP3/WMA is played back on the built-in

disc player:

Selects a folder.

DVD CD

MODE: FU L L AV-OUT: AV - I N

When a disc is played back on the disc changer:

Selects a disc.

• For CD/MP3/WMA/Disc Changer playback and

receiver key operations, see <DDX7025 Basic

Operations> (see page 8).

SRC

DVD CD

• The Easy Control Panel display is cleared when

you touch the center of image display area.

T r a c k

5 : 3 2

During MP3/WMA playback

SRC

DVD MP3/WMA

–

0 : 0 5 : 3 2

During playback on disc changer

SRC

CD CH

T 3

D 1

5 : 3 2

During playback on CD player

SRC

T 3

5 : 3 2

26 English

Displaying the CD/MP3/WMA/

Disc Changer Control screen

You can play the CD/MP3/WMA/disc changer using

various functions.

During CD playback

Calls the CD Menu.

Calls the Sound Effects Menu. (see page 76)

Displays the Source Select screen. (see page 45)

Calls the Setup Menu. (see page 47)

Ejects the disc from the built-in disc player.

Selects a track.

CD Control screen

DVD CD

1 3 : 5 0

Fast Forwards or Rewinds.

Audio

Plays or pauses.

Set Up

Starts or stops Scan Play (that plays the beginning

of each song one after the other).

Direct

SRC

SCRL

SCN

DISP

2:09

REP RDM

TIME

Repeats to play (the present track).

Track

Starts or stops Random Play (to play songs in

random order).

REP

Selects the Disc Name (see <Set Disc Name>, page

31), Disc Text, or Track Text mode for text display.

Scrolls the display text.

;

Switches the play time display between Track, Disc,

and Disc Remaining Time.

Track Number Display

Play Time Display

Appears when a disc is inserted.

Stops to play the built-in disc player.

When pressed twice, the disc is played from its

beginning when you play it in the next time.

Function Indicator

English 27

CD/MP3/WMA/Disc Changer Play Control

MP3/WMA Control screen

During MP3/WMA play

DVD MP3/WMA

1 3 : 5 0

Calls the MP3/WMA Menu.

Fast Forwards.

Audio

Set Up

Direct

SRC

Stops to play.

When pressed twice, the disc is played from its

beginning when you play it in the next time.

SCN

RDM

DISP

SCRL

0:00:38

PEP

Selects a song.

Plays or pauses.

Selects a folder.

KENWOOD

REP

FREP

Starts or stops Scan Play (that plays the beginning

of each song one after the other).

Repeats to play (the present song).

Starts or stops Random Play (to play songs of the

present folder in random order).

Selects the Folder name, File name, Title (ID3/WMA

tag), Artist name (ID3/WMA tag), or Album name

(ID3 tag) for text display.

Scrolls the display text.

Switches the button display.

Repeats to play the song of the present folder.

Folder and File Number Display

Play Time Display

Appears when a disc is inserted.

Function Indicator

Ejects a disc.

28 English

Disc Changer/CD player Control screen

During play by the disc changer/CD player

CD- CH

1 3 : 5 0

Calls the Disc Changer/CD player Menu.

Disc

Audio

Selects a track.

Starts Fast Forward or Fast Rewind when it is held

down.

Set Up

Direct

SRC

Disc

DISP ⁵⁵SCRL

Selects a disc. (Function of Disc Changer)

Plays or pauses.

TIME

SCN

REP RDM

1:24

Starts or stops Scan Play (that plays the beginning

of each song one after the other).

REP

DREP⁵²MRDM

Repeats to play (the present track).

Starts or stops Random Play (to play songs in

random order).

Repeats to play disc (the present disc). (Function of

Disc Changer)

Starts or stops Magazine Random Play (to play

songs of the disc changer in random order).

(Function of Disc Changer)

Switches the button display.

Selects the Disc Name (see <Set Disc Name>,

page 31), Disc Text, or Track Text mode for text

display.

Scrolls the display text.

Switches the play time display between Track, Disc,

and Disc Remaining Time.

Disc Number Display (Function of Disc Changer)

Track Number Display

Play Time Display

Function Indicator

The functions that can be used and the information

that can be displayed will differ depending on the

models being connected.

English 29

CD/MP3/WMA/Disc Changer Play Control

Displaying the CD/MP3/WMA/

Disc Changer Menu screen

Selects options from various function menus.

You can select menu options using various functions.

Returns to the CD/MP3/WMA/Disc Changer Control

screen.

CD Menu screen

Name Set

DVD CD

Audio

Set Up

SRC

The available functions vary depending on the

source used.

30 English

Set Disc Name

Directory List (during

MP3/WMA play)

Names a CD.

The directory of an MP3/WMA disc are listed

for quick search.

Play a CD you wish to name

Call the CD/Disc Changer Menu

Call the MP3/WMA Menu

Select the Set Name mode

Start the Directory List

Name Set

Directory List

Name Set

The

position varies

Fo l d e r Name

MP3/WMA

depending on the disc you are playing.

Audio

Fo l d e r Name

F i l e Name

Set Up

SRC

Enter a name

Fol

Root

For character entry details, see <Character Entry>

(see page 44).

F i l e Name

Open

0:35:27

F i l e Name

Exit the Set Name mode

Returns to the root directory.

Displays the next higher level of hierarchy.

Displays a directory if the subdirectory has a

directory. When you touch the directory, it opens.

Displays a directory if the subdirectory has files

without a directory. When you touch the directory,

it opens and songs in the directory are played.

Displays the MP3/WMA files. When you touch a

file, its song is played back.

• You cannot name an MD or MP3/WMA disc.

• Number of discs that can be stored in memory

Built-in disc player: 10

External CD changer/ player:

Varies depending on the CD changer/ player.

Refer to the CD changer/ player manual.

Plays the selected directory.

Scrolls the list.

Select a song

F i l e Name

Display the desired song and touch the file display.

English 31

CD/MP3/WMA/Disc Changer Play Control

ID3/WMA TAG Display (during Disc Select (during play by

MP3/WMA play)

disc changer)

The ID3/WMA TAG information of MP3/WMA

file is listed.

The discs loaded on the disc changer are listed

for quick disc selection.

Call the MP3/WMA Menu

Calls the Disc Changer Menu

Display the ID3/WMA TAG

Call the Disc Select Menu

Information

Disc Select

MP3

CD- CH

1. D i s c Name

2. D i s c Name

3. D i s c Name

4. D i s c Name

5. D i s c Name

6. D i s c Name

TITLE:

Audio

Set Up

DISP

ARTIST:

ALBUM:

SRC

2:35

Scrolls the list.

Plays the displayed disc.

Selects the Disc Name or Disc Text mode for text

display.

Scrolls the list.

(It is not displayed when a disc changer having 6

or less discs is used.)

Select the desired disc

1. D i s c Name

Touch the desired disc display.

32 English

Mute Telephone

Direct Search

Mute Telephone

Searches for a disc or a song when its number

is entered.

When the telephone is called, the system is

paused automatically.

When the telephone is called...

During play on the built-in disc player

The Phone Call ("CALL") screen appears, and system

is paused.

Select the Direct Search mode

Phone Call ("CALL") screen

1 3 : 5 0

C A L L

Audio

The following items can be searched directly each

time it is pressed.

Set Up

Direct

SRC

CD: Track number, Total play time

MP3/WMA: Folder, File

Enter a disc or track number

—

If you continue to listen the source audio

during phone call...

When searching for a song:

The system restarts to play while the phone call is

continued.

When the call ends...

During play on an external in disc player or disc

changer

Hang up the phone.

The system restarts to play.

Enter a disc or track number

—

When searching for a song:

When searching for a disc:

The operation ends automatically if you do not

operate within 10 seconds.

English 33

TV Control

TV Control ^{(with the optional accessory TV Tuner connected only)}

Various control screens appear in the TV Source mode.

Displaying the TV Picture

screen

TV Band Number Display

Various control screens appear in the TV Source mode.

TV Area Group Display (see page 70)

Memory Number Display

Selects the

TV Pictures.

Channel Number Display

Channel Up Area

Increase the channel.

TV Picture screen

MODE: FU L L

AV-OUT: AV - I N

Group 1

Preset 3

2 c h

T V 1

Channel Down Area

Decrease the channel.

Band/Video Switch Area

Switches to TV1, TV2, or VIDEO.

Information Display Button Area

• For TV picture selection and receiver key

operations, see <DDX7025 Basic Operations>

(see page 8).

Group 1

Preset 3

2 c h

T V 1

• The information display is cleared automatically

after approximately 5 seconds. Also, the

information can be displayed automatically when

it is updated (see page 65).

Displaying the Easy Control

Panel

The Control Panel is displayed in a floating position of the

TV picture.

Switches the source.

Switches to Video (VIDEO).

Switches the TV band (to TV1 or TV2).

Calls up a channel.

Switches the Seek mode.

(see page 36 for the <Seek Mode>)

Displaying the Easy Control Panel

The Easy Control Panel display is cleared when you

touch the center of image display area.

T V 1

MODE: FU L L AV-OUT: AV - I N

VID¹⁰T V¹¹

Group 1

SRC

SEEK

Preset 3

2 c h

T V 1

34 English

Displaying the TV Control

screen

Calls the TV Menu.

;

You can tune in a TV station using various functions.

Calls the Sound Effects Menu. (see page 76)

Displays the Source Select screen. (see page 45)

Calls the Setup Menu. (see page 47)

Switches to VIDEO.

TV Control screen

Switches to TV1 or TV2.

1 3 : 5 0

Select a channel.

Use the <Seek Mode> (see page 36) to change the

channel tuning sequence.

VIDEO

Audio

Set Up

Direct

SRC

Switches between

buttons and

AME²²SEEK

Function buttons to use.

Group

Preset

Selects the Auto Memory mode.

(see page 36 for the <Auto Memory>)

AUTO 1

Switches the Seek mode.

(see page 36 for the <Seek Mode>)

When

buttons appear, you can

call up the channels from memory.

For memory of broadcasting stations, see <Auto

Memory> (see page 36) or <Manual Memory> (see

page 36).

Seek Mode Indicator

TV Area Group Display (see page 70)

Memory Number Display

Displaying the TV Menu screen

You can select menu options using various functions.

Selects options from various function menus.

Returns to the TV Control screen.

The available functions vary depending on the

model used (the tuner specifications and the

broadcasting system that can be received).

TV Menu screen

P r e s e t Se l e c t

Name Set

Audio

Set Up

SRC

English 35

TV Control

Seek Mode

Auto Memory

Sets a TV station selection.

Stores stations with good reception in memory

automatically.

SEEK

Select a band you wish to store in memory

If SEEK is not shown, touch

The mode is switched each time you touch the

button.

Select the Auto Memory mode

Tunes in a station with good

reception automatically.

AUTO 1

AME

Tune in stations in memory one

after another.

AUTO 2

If AME is not shown, touch

Start Auto Memory

Switches to the next channel

manually.

MANUAL

Touch

Auto Memory terminates when 6 stations are stored

or when all stations are tuned in.

The operation ends automatically if you do not

operate within 10 seconds.

Manual Memory

Stores the current receiving channel in

memory.

Select a channel you wish to store in memory

Store in memory

—

are not shown, touch

Continue to touch until the memory number appears.

36 English

Preset Select

Set Station Name

Lists and tunes in stations in memory one after

the other.

Names a station.

Select a station you wish to name

Select a band you wish to call

Call the TV Menu

(P35

)

Selects the Set Name mode

Call the Preset Select Menu

Name Set

P r e s e t Se l e c t

Enter a name

TV1 1) 1ch

TV1 2) 1ch

TV1 3) 1ch

²Menu

For character entry details, see <Character Entry>

(see page 44).

Audio

Set Up

SRC

Exit the Set Name mode

TV1 4) 1ch

TV1 5) 1ch

TV1 6) 1ch

3ch

Tunes in the displayed station.

If the station name is displayed if it has been set.

Returns to the TV Menu.

• You can store up to 20 stations in memory.

• You can set a station name only after you have

applied the parking brake.

English 37

DAB Tuner control

DAB Tuner control ^{(with the optional accessory DAB tuner connected only)}

Various control screens appear in the DAB Tuner source mode.

Displaying the Easy Control

Panel

The DAB Tuner Control Panel is displayed in a floating

position of the selected picture.

Switches the source.

Switches the band (to DAB1/2/3).

Selects a service.

Selects the Ensemble.

Switches the Seek mode.

(see page 40 for the <Seek Mode>)

Display the Easy Control Panel

• For system key operations, see <DDX7025 Basic

Operations> (see page 8).

MODE: FU L L AV-OUT: AV - I N

• The Easy Control Panel display is cleared when

you touch the center of image display area.

SRC

DAB

BAND

D A B 1

SEEK

2 2 0 . 0 9 4 M H Z

38 English

Displaying the DAB Tuner

Control screen

You can select the Ensemble and services using various

functions.

Calls the DAB Tuner Menu.

Calls the Sound Effects Menu. (see page 76)

Displays the Source Select screen. (see page 45)

Calls the Setup Menu. (see page 47)

Switches the band (to DAB1/2/3).

Selects a service.

DAB Tuner Control screen

DAB

1 3 : 5 0

Selects the Ensemble.

Ser v i c e

Band

Audio

Switches between

buttons and

Set Up

Function button to use.

Direct

SRC

Ser v i c e

Selects the primary or secondary operation.

P/S ¹⁴AME SEEK DISP

Selects the Auto memory mode. (see page 40 for

the <Auto Ensemble memory>)

DAB1

Preset2

Service Label

Switches the Seek mode.

(see page 40 for the <Seek Mode>)

AUTO1

Changes the display between Ensemble label, PTY

label, Component label, Region label, and Audio

quality.

When

buttons appear, you can

call a service from memory.

Seek Mode Indicator

Displaying the DAB Tuner

Menu screen

Selects options from various function menus.

Returns to the DAB Tuner Control screen.

;

You can select menu options using various functions.

For DAB Tuner function details, see the Instruction

Manual of DAB Tuner (optional accessory).

DAB Tuner Menu screen

DAB

Service Select

Audio

Langua g e F i l t e r

Set Up

SRC

PTY Sea r c h

DAB I n forma t i o n

English 39

DAB Tuner control

Seek Mode

Service Preset Memory

A service selection method can be set.

The current receiving service is stored in

memory.

SEEK

Select a service you wish to store in memory

Band

If SEEK is not shown, touch

The mode display is switched each time you touch

the button.

Ser v i c e

Store in memory

Tunes in an ensemble with good

reception automatically.

AUTO 1

AUTO 2

MANUAL

—

Selects services in memory one

after another.

are not shown, touch

Switches to the next channel

manually.

Auto Ensemble Memory

An ensemble with good reception is stored in

memory automatically.

Select a band you wish to store in memory

Band

Select the Auto Memory mode

AME

If AME is not shown, touch

Start Auto Memory

Touch

Auto Memory terminates when 6 ensembles are

stored or when all ensembles are tuned in.

40 English

Service Select

Language Filter

The service list of the currently receiving

ensemble is displayed for your selection.

The languages are list for your selection.

Call the DAB Tuner Menu

Call the Language Filter Menu

Call the Service Select Menu

Languag e F i l t e r

Service Select

DAB

Audio

Ser v i c e Name

DAB₃

Audio

Language

Set Up

E n g l i s h

Ser v i c e Name

Direct

SRC

Set Up

SRC

SRCH

Ser v i c e Name

Re t u r n

220.094 MHz

Selects a language.

Searches for the selected language.

Returns to the DAB Tuner Menu.

Selects a service.

Scrolls the service list.

Returns to the DAB Tuner Menu.

Select a language you wish to use

Select a service

Ser v i c e Name

Search for the language

SRCH

English 41

DAB Tuner control

Search for Program Type

Select a Language

The services are received when you set its

program type.

Display the Language select screen

Call the DAB Tuner Menu

LANG

DAB

Audio

PTY

Set Up

N e w s

Language

Call the PTY Search Menu

Direct

SRC

E n g l i s h

SRCH

PTY Sea r c h

Re t u r n

DAB

Selects a Language.

Audio

PTY

Searches for the program type.

Returns to the PTY Search Menu.

Set Up

N e w s

Direct

SRC

Select a Language

SRCH

LANG

Re t u r n

Selects a program type.

Searches for the program type.

Search for the program type

Displays the Language select screen.

Returns to the DAB Tuner Menu.

SRCH

Select a program type

42 English

DAB Information

DAB Announcement

The DAB information is displayed.

When the Announcement you have turned on

starts, any source is switched to the

Announcement automatically.

Call the DAB Tuner Menu

When the announcement starts...

The Announcement screen appears automatically.

Announcement screen

Display the DAB Information screen

1 3 : 5 0

D A B

Audio

DAB I n forma t i o n

Set Up

Direct

SRC

DAB

Service Label:

Audio

Traffic News

Set Up

SRC

Ensemble Label:

Component Label:

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu. (see page 47)

Displays the DAB information (such as Service

label, Ensemble label, Component label, Audio

quality, Region label, and Dynamic label).

Scrolls the information display.

Returns to the DAB Tuner Menu.

English 43

Character Entry

How To Use the Character

Entry screen

When you select the Set Disc Name mode or

others, the following screen appears for

character entry.

Character Entry screen

KENWOOD

Space

Shifts the cursor.

Enters a space.

If you erase a character, locate the cursor on it

and touch this button.

Enters characters.

Scrolls up or down the character button display.

Exits the Character Entry mode and returns to the

previous screen.

You can enter characters only after you have

applied the parking brake.

44 English

Source Select

The source you wish to listen to can be selected quickly.

Displaying the Control screen

Press this key several times unit the Control screen

appears.

Control screen

DVD V I DEO

1 3 : 5 0

Audio

Set Up

Direct

SRC

SCRL

T0:05:20

TIME

REP

Chap

KENWOOD

Title

The Source Select screen can be displayed from

the control screen of any source.

T-REP

Displaying the Source Select

screen

Select the source.

Returns to the Control screen previously displayed.

Direct

SRC

Source Select screen

STANDBY

Audio

TUNER

Set Up

DVD

SRC

VIDEO

CD CH

MD CH

English 45

Adjusting the Monitor Display Position and Quality

You can adjust the position and picture quality of the monitor.

Displaying the Screen Control

screen

You can adjust the picture quality using the following

keys.

Brightness Control

Tint Control

Displayed for an NTSC system image on TV or

Video.

Color Control

Displayed on the TV and Video screen only.

Screen Control screen

Contrast Control

Black Level Adjustment

Displays the Adjust Monitor Position screen.

(see <Displaying the Tilt Adjust screen>, page 46)

Tilt

Returns to the previous screen.

The Screen Control screen is displayed only when

you have applied the parking brake.

Displaying the Tilt Adjust

screen

Monitor Tilt Adjustment

You can set the monitor tilt.

The monitor fully closes.

Returns to the Screen Control screen.

Returns to the previous screen.

Tilt

Tilt Adjust screen

If you turn the power off, the panel will close.

However, if you turn the power back on, it will

return to the adjusted tilt.

T i l t A d j u s t

S c r e e n

T i l t

F u l l C l o s e

46 English

Setup Menu

You can set up various receiver parameters.

Displaying the Control screen

Press this key several times until the Control screen

appears.

Control screen

DVD V I DEO

1 3 : 5 0

Audio

Set Up

Direct

SRC

SCRL

T0:05:20

TIME

REP

Chap

KENWOOD

Title

You can call the same Setup Menu for the Control

screen of each source.

T-REP

Displaying the Setup Menu

screen

Scrolls the Setup Menu.

Calls each Setup Menu.

Set Up

Calls the Sound Effects Menu. (see page 76)

Returns to the Control screen of the previous

source.

Setup Menu screen

• Your setup on the <Sound Effects Menu> is

adjusted automatically according to your <Audio

Set Up> (see page 48) on the Setup menu. We

recommend you to complete the <Audio Set Up>

first, then set up the <Sound Effects Menu>.

Set Up

Audi o S e t Up

DVD SETUP

Audio

Set Up

Sys t em S e t U p

AV I / F S e t Up

User I / F S e t Up

SRC

• The available functions vary depending on the

model used (the tuner specifications and the

broadcasting system that can be received).

English 47

Setup Menu

Audio Set Up

You can setup a speaker network, etc.

Displaying the Audio Set Up

screen

Returns to the Control screen of the previous

source.

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

Audi o S e t Up

Displays the X'Over setup screen. (see page 49)

Speaker setup screen

Sets up the front speaker type to fine-tune for the

optimal equalizer curves.

Standard: Setup for general diameter speakers

Narrow: Setup for small diameter speakers

Middle: Setup for small diameter woofer

Audio

X' Ov e r

Set Up

SRC

Fr o n t L&R

Standard

Wide:

Setup for large diameter woofer

Speaker

48 English

Crossover Network Setup

You can set a crossover frequency of speakers.

(P48

)

X' Ov e r

X'Over setup screen

X' Over

HPF Front FREQ

THR

HPF Rear FREQ

THR

LPF SUB FREQ

THR

Rev e r s e

Return

Sets a Front High Pass Filter frequency.

You can select any of the following frequency.

Through, 40, 60, 80, 100, 120, 150, 180, 220 Hz

Sets a Rear High Pass Filter frequency.

You can select any of the following frequency.

Through, 40, 60, 80, 100, 120, 150, 180, 220 Hz

Sets a Sub woofer Low Pass Filter frequency.

You can select any of the following frequency.

50, 80, 120, Through Hz

Sets the phase of subwoofer output.

The phase is reversed 180 degrees when set to

"Reverse".

Returns to the Speaker setup screen.

English 49

Setup Menu

Audio Set Up ^{(with the optional accessory DSP unit connected only)}

You can set up more detailed settings by connecting the optional accessory DSP

Displaying the Car Type Set Up

screen

If your vehicle type is selected, the Digital Time

Alignment is set automatically (for timing adjustment of

sound output for each channel) to have the highest

surround effects.

Returns to the Control screen of the previous

source.

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

Sets up the car type you use together with this unit.

Audi o S e t Up

Displays the DTA (Digital Time Alignment) Setup

screen. (see page 52)

You can adjust the digital time alignment that was

set automatically when you selected the car type.

Car Type Set Up screen

Displays the Speaker Set Up screen.

DTA

Audio

Set Up

Car Type

You cannot set up "Car Type" when "Position

Setting" (see page 84) is "All".

Sma l l

SRC

Car Type

50 English

unit.

Displaying the Speaker Set Up

screen

When the speaker type and size are set, the speaker

crossover network and equalizer curve are set

automatically.

Displays the X'over (HPF) screen.

(See <High Pass Filter Setup>, page 54)

Display the X'over (LPF) screen.

(See <Low Pass Filter Setup>, page 54)

Sets up the front speaker type to fine-tune for the

optimal equalizer curves.

Standard: Setup for general diameter speakers

Narrow: Setup for small diameter speakers

Middle: Setup for small diameter woofer

Speaker Set Up screen

Wide:

Setup for large diameter woofer

X' Ov e r HPF

Select the speakers for Multi-channel sounds.

"3/2": Center speaker, Front speaker, Rear speaker

"2/2": Front speaker, Rear speaker

"3/0": Center speaker, Front speaker

"2/0": Front speaker

Audio

X' Ov e r LPF

Set Up

₁₀Mu l t i Channel

3 / 2

SRC

Fr o n t L&R

Standard

Sub Woo f e r

O f f

Set the use or no use of Sub Woofer.

Displays the Channel Level Setup screen.

Displays the Car Type Set Up screen.

Speaker

• "X’Over HPF" and "X’Over LPF" can be set only

when "Sub Woofer" is set to "On".

• To turn the Center speaker on in the "Multi

channel" settings, turn "Dolby Pro Logic" (see

page 83) on.

Displaying the Channel Level

screen

Selects a speaker to be set.

(see <Channel Level>, page 52)

You can set the volume at each setup position.

Sets the speaker volume.

(see <Channel Level>, page 52)

Starts or stops test signal tone output for setup

check.

Channel Level screen

Displays the Speaker Set Up screen.

• Your setup on the <Sound Effects Menu> is

adjusted automatically to get the best sound

effects according to the car type and speaker you

have set on the <Audio Set Up> (see page 48).

We recommend you to complete the <Audio Set

Up> first, then set up the <Sound Effects

Menu>.

You can fine-adjust the automatic set value by

<DTA Setup> (see page 52) or <Parametric

Equalizer> (see page 80).

Audio

Set Up

Test

SRC

Cent er

+1 0dB

Chann e l L e v e l

• Stop the test signal tone if you have finished

setting up the Channel Level. If you leave the test

signal tone on, you may not be able to set up

other settings.

English 51

Setup Menu

Channel Level

DTA Setup

Set the volume at each setup position.

Manually set the sound output timing of each

channel.

Select a speaker you wish to adjust

Display the DTA Setup screen

(P50

)

DTA

Channel Level setup screen

DTA Setup screen

DTA

Audio

Set Up

Test

Pr e s e t

SRC

Cent er

+1 0dB

Front

1 m

Chann e l L ev e l

Return

Left front speaker

Right front speaker

Left rear speaker

Right rear speaker

Center speaker

Selects a speaker to be adjusted.

Sets the distance between the selected speakers

to adjust delay time.

Stores the adjusted status in memory or calls it

from memory.

Returns to the Car Type Set Up screen.

Adjust the volume

Select a speaker you wish to adjust

Front speaker

Rear speaker

Subwoofer

Center speaker

52 English

Set a delay time

The speakers are virtually moved to the desired

distance.

When the values of center speaker and front

speakers increase, they are virtually moved forward.

When the values of rear speakers and subwoofer

increase, they are virtually moved backward.

Store or call your setup into/from memory

To store your setup in memory

Pr e s e t

Continue to touch more than 2 seconds.

To call your setup from memory

Pr e s e t

English 53

Setup Menu

High Pass Filter Setup

Low Pass Filter Setup

You can manually set a High Pass Filter of

Crossover Network.

You can manually set a Low Pass Filter of

Crossover Network.

(P51

)

(P51

)

X' Ov e r HPF

X' Ov e r LPF

HPF F r ont

100 Hz

HPF Rear

100 Hz

Rev e r s e

Sets a crossover frequency of Front High Pass

Filter.

Sets a crossover slope of Front High Pass Filter.

Sets a crossover frequency of Rear High Pass

Filter.

Sets a crossover frequency of Low Pass Filter.

Sets a crossover slope of Low Pass Filter.

Sets the phase of subwoofer output.

The phase is reversed 180 degrees when set to

"Reverse".

Sets a crossover slope of Rear High Pass Filter.

Sets a crossover frequency of Center High Pass

Filter.

Returns to the Speaker Set Up screen.

Sets a crossover slope of Center High Pass Filter.

Returns to the Speaker Set Up screen.

"HPF Center" can be set only when "Multi

Channel" (see page 51) is set to "3/2" or "3/0".

54 English

English 55

Setup Menu

DVD Setup

You can set up the DVD play.

Displaying the DVD SETUP 1

screen

Returns to the Control screen of the previous

source.

DVD SETUP

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

Selects a disc menu language.*¹

(See <Language Setup>, page 58)

DVD SETUP 1 screen

Selects a subtitle language.*¹

(See <Language Setup>, page 58)

Selects an audio language.*¹

(See <Language Setup>, page 58)

Menu LANG

Sub t i t l e LANG

Audio

Set

Set Up

Aud i o LANG

Dynam i c R ange Con t r o l

SRC

Sets the dynamic range.*²

(

Wide)

Mi d n i g h t

The dynamic range is reduced by changing from

"Wide" to "Normal" and from "Normal" to "Midnight".

You can easy to listen a small sound when the

dynamic range is narrow.

DVD S ETUP

This is effective only when you are using a Dolby

Digital software.

Displays the DVD SETUP 2 screen.

DVD SETUP

is not shown,

to display it.

touch

56 English

Displaying the DVD SETUP 2

screen

Sets an angle mark display. (

On)

Selects the screen display mode.*¹(

"16:9": Displays wide pictures.

16:9)

"4:3 LB": Displays wide pictures in the Letter Box

format (having black stripes at the top and

bottom of screen).

DVD SETUP 2 screen

"4:3 PS": Displays wide pictures in the Pan & Scan

format (showing pictures cut at the right

and left ends).

Ang l e Mar k

Sc r e e n Ra t i o

Audio

O f f

S e t

Set Up

Displays the Parental Lock screen.*¹(

(See <Parental Level Setup>, page 59)

OFF)

4 : 3 LB

SRC

Pa l en t a l L ev e l

Off

Keep "AUTO" to use.

Output

AUTO

Displays the DVD SETUP 1 screen.

DVD S ETUP

*¹Disabled when a DVD is being played.

*²Disabled when the Zone function is On.

English 57

Setup Menu

Language Code Table

Language Setup

Abbreviation

Language

Abbreviation

Afar

Latvian, Lettish

Malagasy

Maori

Select a language you use for the speech and

menus.

Abkhazian

Afrikaans

Amharic

Arabic

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay

Display the Language Setup screen

Assamese

Aymara

Azerbaijani

Bashkir

See <Displaying the DVD SETUP 1 screen> (see

page 56) and select a language you wish to use.

Byelorussian

Bulgarian

Bihari

Maltese

Burmese

Nauru

Audio LANG

Bislama

Bengali, Bangla

Tibetan

Nepali

Dutch

Norwegian

Occitan

(Afan) Oromo

Oriya

Breton

Catalan

O R I G N⁴

Corsican

Czech

Punjabi

C l e ar

Cancel

E n t e r

Welsh

Polish

Danish

Pashto, Pushto

Portuguese

Quechua

Rhaeto-Romance

Kirundi

German

Bhutani

Greek

Enters a language code.

English

Cancels the language setup and returns to the

DVD SETUP 1 screen.

Esperanto

Spanish

Estonian

Basque

Persian

Romanian

Russian

Kinyarwanda

Sanskrit

Sindhi

Clears the language code.

Sets the original audio language.

(It appears during audio language setup.)

Sets the language and returns to the DVD SETUP

1 screen.

Finnish

Sangho

Fiji

Serbo-Croatian

Singhalese

Slovak

Faroese

French

(It appears after you have entered a language

code.)

Frisian

Slovenian

Samoan

Shona

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Enter a language code

Somali

Albanian

Serbian

See the Language Code Table shown at right to

select the desired language.

Siswati

Hindi

Sesotho

Sundanese

Swedish

Swahili

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

Set the language you use

Tamil

Telugu

Tajik

E n t e r

Indonesian

Icelandic

Italian

Thai

Tigrinya

Turkmen

Tagalog

Setswana

Tongan

Hebrew

Japanese

Yiddish

Javanese

Georgian

Kazakh

Turkish

Tsonga

Tatar

Greenlandic

Cambodian

Kannada

Korean

Twi

Ukrainian

Urdu

Uzbek

Kashmiri

Kurdish

Kirghiz

Vietnamese

Volapuk

Wolof

Latin

Xhosa

Lingala

Yoruba

Laotian

Chinese

Zulu

Lithuanian

58 English

Parental Level Setup

Display the Parental Level Setup screen

Sets a parental level.

E n t e r

Display the Parental Level code number screen

(P57

)

P a r e n t a l L e v e l

S e t

Le v e l 5

P a r e n t a l Pa s s

* * * *

Return

Le v e l 5

Enter

Sets a parental level.

C l e ar

Cancel

Returns to the DVD SETUP 2 screen.

Set a parental level and a country code

Enters a code number.

Cancels the current setup and returns to the DVD

SETUP 2 screen.

Clears the code number.

Displays the present parental lock level.

Determines the code number and displays the

Parental Level Setup screen.

Enter the parental level setup

Enter the code number

Return

—

• If a disc has a higher parental lock level, the

audience needs to enter the code number.

• The parental lock level varies depending on a

loaded disc.

• The number you enter first is set as your code

number.

• If a disc has no parental lock, any audience can

play it back even when you have set the

parental lock.

• You can clear the code number by pressing the

Reset button.

English 59

Setup Menu

System Setup

You can set up the system parameters.

Displaying the System Set Up

1 screen

Returns to the Control screen of the previous

source.

Sys t em S e t U p

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

System Set Up 1 screen

Turns the key touch tone On or Off. (

On)

Allows scrolling of text display on the Source

Control screen. ( Manual)

"Auto": Scrolls the screen automatically.

"Manual": Allows you to scroll the screen manually.

Beep

Audio

O f f

Set Up

Sc r o l l

Manua l

Remo t e Se n s o r

SRC

Selects a remote control signal. ( On)

When turned "Off", the remote control of TV

reception is rejected.

Displays the System Set Up 2 screen.

System Se t Up

Sys t em S e t U p

is not shown,

to display it.

touch

60 English

Displaying the System Set Up

2 screen

Sets a music CD playback. (

"1" Automatically recognizes and plays back an

MP3/WMA disc, a DVD or a music CD.

"2" Forcibly plays back a disc as a music CD.

Select "2" if you wish to play a music CD having

a special format or if you cannot play a disc in

the "1" position.

System Set Up 2 screen

• You cannot play an MP3/WMA/VCD disc in the "2"

position. Also, you may not play some music

CDs in the "2" position.

CD Read

Audio

Set Up

Key ILLUMI

Green

• Your setup is disabled when the disc is being

played.

SRC

Selects an illumination color of receiver keys.

(

Red)

"Green" Green

System Se t Up

"Red"

Red

Displays the System Set Up 1 screen.

English 61

Setup Menu

AV Interface

You can set audio and visual (AV) interface parameters.

Displaying the AV I/F 1 screen

Returns to the Control screen of the previous

source.

AV I / F S e t Up

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

AV I/F 1 screen

Selects a navigation system connection. (

RGB)

"RGB" Allows the Kenwood’s Navigation System

to connect via its interface cable.

"AV-IN": Allows a third-party navigation system to

connect via the AV INPUT port.

NAV

AV - I N Name

Audio

AV - I N

Set Up

V I DEO

"OFF" Must be used if no navigation system is

SRC

AV - I N

connected. (The navigation display is

Nor ma l

R-CAM View

Nor ma l

cancelled when the AV source is switched.)

Sets a name to be displayed when you select a

system that is connected via the AV INPUT port.

AV I / F

(

VIDEO)

If you have set the navigation system connection to

"AV-IN", the display is fixed to "NAV".

Sets an image display of the system that is

connected via the AV INPUT port. ( Normal)

"Normal" When the image source is switched, an

image entered via the AV INPUT port is

displayed.

"AUTO": When an image signal is entered via the

AV INPUT port, this image is displayed.

Sets how the rear camera image is displayed.

"Reverse": Displays with left and right reversed.

"Normal": Displays as it is.

"R-CAM View" can be set only when "AV-IN Name"

is set to "R-CAM".

Displays the AV I/F 2 screen.

AV I / F S e t Up

is not shown,

to display it.

touch

62 English

Displaying the AV I/F 2 screen

Selects an AV source to be output at the AV

OUTPUT port. (

AV-IN)

If you select DVD as a source when the optional

accessory DSP unit is connected, no DVD sound is

output to the AV output port.

Selects speakers used for voice guidance of the

AV I/F 2 screen

navigation system. (

F-Left)

"F-Left" Uses the front left side speaker for voice

AV -OUT

N AV I n t e r r u p t i o n

F - A l l

NAV Guide Volume Level

guidance.

Audio

AV - I N

"F-Right": Uses the front right side speaker for voice

guidance.

Set Up

SRC

"F-All":

Uses both front speakers for voice

guidance.

L i n e Mu t e

Adjusts the volume for voice guidance of the

O f f

navigation system. (

19)

AV I / F

Mutes the volume during voice guidance of the

navigation system. ( On)

When turned "On", the volume level drops for voice

guidance.

Displays the AV I/F 1 screen.

English 63

Setup Menu

User Interface

You can set up user interface (IF) parameters.

Displaying the User I/F 1

screen

Returns to the Control screen of the previous

source.

User I / F S e t Up

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

User I/F 1 screen

Switches the wall paper.

Displays the User I/F 2 screen.

Audio

User I / F S e t Up

is not shown,

to display it.

Set Up

Wall Paper

touch

Wall

SRC

User I / F

64 English

Displaying the User I/F 2

screen

Sets an on-screen display of the navigation screen.

(

Auto)

If you set to "Auto", an information is displayed for 5

seconds when updated.

Sets an on-screen display of the video playback

User I/F 2 screen

screen. (

Auto)

If you set to "Auto", an information is displayed for 5

seconds when updated.

On SCRN NAV

On SCRN VIDEO

On SCRN DVD

On SCRN TV

MANU

Audio

Sets an on-screen display of the DVD playback

Set Up

screen. (

MANU)

SRC

If you set to "Auto", an information is displayed for 5

seconds when updated.

Sets an on-screen display of the TV screen.

(

Auto) (with the optional accessory TV tuner

User I / F

connected only)

If you set to "Auto", an information is displayed for 5

seconds when updated.

Displays the User I/F 1 screen.

English 65

Setup Menu

Touch Panel Adjust

Adjustment

You can adjust the touch panel operations.

Display the Touch Panel Adjust screen

Touch the center of left lower and right upper

when requested

Touch Adjust

is not shown, touch

to display it.

³Menu

Touch Ad j u s t

Audio

S e t

Set Up

SRC

T ouch

Returns to the Control screen of the previous

source.

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

Allows you to start touch panel adjustment.

Start to adjust the touch panel

S e t

Touch Ad j u s t

Cancel

Reset

Cancels the adjustment and returns to the Touch

Panel Adjust screen.

Resets to the initial status.

66 English

Clock

Adjusts the clock time.

Display the Clock Screen

Clock Adjust

is not shown, touch

to display it.

³Menu

PM 1 1 : 1 8

Audio

Set Up

Res e t

SRC

SYNC

O f f

C lock

Returns to the Control screen of the previous

source.

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

Clock time display.

Adjusts hours.

Adjusts minutes.

Sets "00" minute.

→

Setup examples: 3:00~3:29

3:00

4:00

3:30~3:59

Sets the clock time in synchronous with the time

data sent from the RDS station. (

On)

When turned "On", the synchronous mode starts

and the clock cannot be adjusted manually.

Adjust the clock time

English 67

Setup Menu

Security Code Setup

Start the security code registration

You can set a security code to protect your

receiver system against theft.

S e t

When the Security Code function is activated it can't

be released.

Note, your Security Code is the 4 digit number

entered in your "Car Audio Passport" in this package.

Pa ss Wor d

* * * *1 s t

Display the Security Code Setup screen

Security Set Up

Clear

Cancel

Enter

is not shown, touch

Enters a security code.

Clears your entry.

to display it.

Cancels the registration and returns to the

Security Code Setup screen.

Enters the security code.

Sec u r i t y Code

S e t

O f f

Audio

S I

Set Up

SRC

Enter a security code

—

Secur i t y

Input a four-digit number.

Returns to the Control screen of the previous

source.

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

Allows you to start security code registration.

E n t e r

Turns the SI function On or Off.

If turned "On", the burglar alarm lamp flashes

when the vehicle ignition is off.

Reenter the security code

If you have already completed the code

registration, the S e t is not displayed.

Reenter the same security code as that you have

entered in Step 3 for confirmation.

If you enter a different security code, the screen

returns to Step 3 (for the first code entry).

E n t e r

Your security code has been registered.

If you press the Reset button or if you disconnect

your Receiver from the battery after the code

registration, you need to enter the registered

security code.

See below for details.

68 English

If you have pressed the Reset button or if you

have disconnected the Receiver from battery...

Enter the correct security code

—

You must enter the same security code as that you

have entered in Step 3 above.

Enter the security code

E n t e r

Now, you can use your Receiver.

If you enter an incorrect security code, you

cannot use your Receiver for a while.

Incorrect entry count Receiver inoperable

time

—

5 minutes

1 hour

24 hours

4 or more

English 69

Setup Menu

TV Setup ^{(with the optional accessory TV Tuner connected only)}

The TV signal receiving areas can be set.

Displaying the TV1 Area Set Up

screen

Returns to the Control screen of the previous

source.

TV S e t U p

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

TV1 Area Set Up screen

Sets the present TV1 receiving area.

Displays the TV2 Area Set Up screen.

Aust r a l i a

Audio

Spa i n

Sw i t z e r l a nd Denmark

Germany

Sweden

No r w a y

TV S e t U p

is not shown,

to display it.

Set Up

touch

Yougos l a v i a

Ne t h e r l and

P o r t u gal

Croa t i a

Bel g i um

F i n l and

SRC

TV1 Area Set

Displaying the TV2 Area Set Up

screen

Sets the present TV2 receiving area.

Displays the TV1 Area Set Up screen.

TV2 Area Set Up screen

Aust r a l i a

Audio

Spa i n

Sw i t z e r l a nd Denmark

Germany

Sweden

No r w a y

Set Up

SRC

Yougos l a v i a

Ne t h e r l and

P o r t u gal

Croa t i a

Bel g i um

F i n l and

TV2 Area Set

70 English

RDS Setup

The related RDS parameters can be set.

Displaying the RDS Set Up 1

screen

Returns to the Control screen of the previous

source.

RDS S e t U p

Calls the Sound Effects Menu. (see page 76)

Calls the Setup Menu.

RDS Set Up1 screen

Sets a news bulletin interrupt time.

Turns the Alternative Frequency function On or Off.

(

On)

News

Audio

Of f

Turns the Region Restriction function On or Off.

Set Up

(

On)

O f f

SRC

Reg i onal

Turns the Auto TP Seek function On or Off. (

Displays the RDS Set Up 2 screen.

On)

Au t o TP S e ek

RDS Se t Up

RDS S e t U p

is not shown,

to display it.

touch

Displaying the RDS Set Up 2

screen

Selects a display language for the PTY function.

Displays the RDS Set Up 1 screen.

RDS Set Up2 screen

Language Se l e c t

German

Audio

Set Up

SRC

RDS Set Up 2

English 71

Setup Menu

DAB Set Up ^{(with the optional accessory DAB Tuner connected only)}

The DAB reception can be set.

Displaying the DAB Set Up

screen

Calls the Sound Effects Menu. (see page 76)

Returns to the Control screen of the previous

source.

DAB Set Up

Calls the Setup Menu.

DAB Set Up screen

Turns the DAB Priority On or Off.

Turns the Dynamic Range Control function On or

Off.

DAB P r i o r i t y

DRC

O f f

Audio

Turns the Regional Announcement function On or

Off.

Set Up

Reg i o n a l I nt.

SRC

PTY Watch

Sets a program type to be selected automatically

when the receiving ensemble starts.

P T Y Wa t c h O f f

Announcement Se l e c t S e t

DAB Se t Up

Displays the Announcement Selection screen.

DAB Set Up

is not shown,

to display it.

touch

72 English

Announcement Selection

Various announcement reception parameters

can be set.

Displays the Announcement Selection screen

S e t

Announcement

ea t her

O f f

Ev ent

O f f

Spe ci a l Ev ent

O f f

Radio I nfo

Return

Turns the Announcement Reception function On

or Off.

Scrolls the Announcement items.

Returns to the DAB Set Up screen.

Set the announcement parameters

etc.

ea t her

Traffic News:

Traffic information

Transport News: Time table information of public

transportation services

Warning:

Lower priority items than alarms

(power failure, cutoff of water

supply and others)

News:

News flash

Weather:

Event:

Weather forecasting

Event information

Special Event:

Radio Info:

Undetermined event information

Programme information, advance

notice

Sports news:

Sports news

Financial news: Financial news

Terminate the setup

Return

English 73

Setup Menu

AMP Control ^{(with the optional accessory LX Power AMP connected only)}

Sets the power amp connected via the LX bus.

Displaying the AMP Control

screen

Calls the Setup Menu.

Calls the Sound Effects Menu. (see page 76)

AMP Ctrl

Returns to the Control screen of the previous

source.

AMP Control screen

Setup option and value display

Select a setup option.

Selects a set value.

Audio

Set Up

Enters the set value.

SRC

AMP Ctrl

• If

is not shown,

to display it.

touch

A M P 1 VO LT 1 4 . 4 V

A M P C o n t r o l

S e t

• For the model name of amp you can control from

the system, see the amp’s catalog.

• For the options and values you can change and

for the amp’s operation when changed, see the

amp’s instruction manual.

74 English

English 75

Sound Effects Menu

You can set up the receiver sound effects.

Displaying the Control screen

Control screen

DVD V I DEO

1 3 : 5 0

Audio

Set Up

Direct

SRC

SCRL

T0:05:20

TIME

REP

Chap

KENWOOD

Title

You can display the same Sound Effects Menu on

the Control screen of any source.

T-REP

Displaying the Sound Effects

Menu screen

Calls the Sound Effects Menu.

Calls the Setup Menu. (see page 47)

Audio

Returns to the Control screen of the previous

source.

Sound Effects Menu screen

• Your setup on the <Sound Effects Menu> is

adjusted automatically according to your <Audio

Set Up> (see page 48) on the Setup menu. We

recommend you to complete the <Audio Set Up>

first, then set up the <Sound Effects Menu>.

Aud i o Co n t r o l

Equa l i z e r

Aud i o

Audio

Set Up

SRC

Zone Con t r o l

• Displayed items vary depending on the optional

accessory connected.

76 English

Audio Control

You can adjust the front and rear and right and left audio balance.

Displaying the Audio Control

1 screen

Returns to the Control screen of the previous

source.

Aud i o Co n t r o l

Calls the Setup Menu. (see page 47)

Calls the Sound Effects Menu.

Adjusts the right and left volume balance.

Adjusts the front and rear volume balance.

Audio Control 1 screen

F r o n t

FAD F12

BAL R1 2

Adjusts the volume of the present source based on

the difference level of original volume.

Audio

Set Up

If you have increased the volume first, then

reduced it using the "Vol. Offset", the big sound

may suddenly be generated when you switch to

another source.

SRC

SUB -15

R e a r

Vo l . O f f s e t

- 1 5

LOUD

O f f

Adjusts the subwoofer volume.

Aud i o Con t ro l 1

Turns the Loudness control function On or Off.

(Does not appear when the optional accessory DSP

unit is connected.)

If turned "On", high and low tones are automatically

enhanced during low volume. (

On)

Displays the Audio Control 2 screen.

Displaying the Audio Control

2 screen

Adjusts the bass boost of the B.M.S power

amplifier (optional accessory).

You may not set some models of power amp boost

to "+18". See the catalog or instruction manual of

power amplifier.

Set the center frequency of bass boost you have set

for the "AMP Bass".

If you set it to "Low", the center frequency is

dropped for 20 to 30%.

Audio Control 2 screen

Audio

BMS AMP Bass

F l a t

BMS AMP FREQ

Set Up

SRC

Displays the Audio Control 1 screen.

Normal

Low

Aud i o Con t ro l 2

English 77

Sound Effects Menu

Equalizer

You can set up the equalizer.

Displaying the Equalizer

screen

Returns to the Control screen of the previous

source.

Equa l i z e r

Calls the Setup Menu. (see page 47)

Calls the Sound Effects Menu.

Equalizer screen

Select the adjustment items for the Tone Curve

setup. (Does not appear when the optional

accessory DSP unit is connected.)

If you set it to "Off", only "Level" can be set up for

Tone Curve.

Tone

System

Audio

Set Up

N a t u r a l

SRC

Tone

Displays the Tone curve setup

screen. (see page 79)

Syst em Q -Ex

O f f

P-EQ

: Displays the Parametric Equalizer

screen. (see <Parametric Equalizer>

page 80) (with the optional accessory

DSP unit connected)

Equa l i zer

You can adjust the value set for the

Equalizer Curve Type.

Selects an equalizer curve type.

You can select any of the following equalizer curves.

System Q

• "Natural"

• "Rock"

• "Pops

• "Easy"

• "Top 40"

• "Jazz"

• "User" (when the tone curve (page 79) is set up)

KBS (with the optional accessory DSP unit connected)

• "Natural"

• "Top 40"

• "Rock"

• "Dance"

• "Vocal"

• "Classic"

• "User" (when Parametric Equalizer (page 80) is

set up)

78 English

Tone curve setup

Set a Q factor

Q Factor

You can set a Tone curve.

Display the Tone setup screen

You can set it up only when Bass or Middle is

adjusted.

Tone

Close the Tone setup screen

Tone setup screen

Tone

FREQ

Bass

Return

- 5

Le v e l

F a c t o r

Midd l e

T r e b l e

1 . 0

O f f

Bass DC EXT

Re t u r n

Bass adjustment items are displayed.

Middle adjustment items are displayed.

Treble adjustment items are displayed.

Bass DC Extend settings

If turned "On", it extends the bass center

frequency to the low register by approximately

20%.

Returns to the Equalizer screen.

Tone curve can be set for each source.

Select a frequency band you wish to adjust

Bass

Midd l e

T r e b l e

You can adjust the following frequency bands.

Bass: 60, 70, 80, 100/150 (When "Q Factor" is

"2.00") Hz

Middle: 500, 1k, 1.5k, 2k Hz

Treble: 10k, 12.5k, 15k, 17.5k Hz

Set a center frequency

FREQ

Set a level

Level

English 79

Sound Effects Menu

Parametric Equalizer

Set a Q value

You can Manually set the equalizer curve by

adjusting the center frequency, gain and Q

value. (with the optional accessory DSP unit

connected)

Store or call the equalizer curve into/from

memory

Display the Parametric Equalizer screen

To store the equalizer curve in memory:

P-EQ

—

P aramet r i c Equ a l i z e r

Continue to touch

2 seconds.

more than

Band3 Band4

¹Band1 Band2

800

KH z

2 . 2 5

KH z

2 . 2 5

FREQ

G a i n

+12

To call the equalizer curve from memory:

3. 0 0

—

Re t u r n

Touch

of the equalizer curve

Select a band to be adjusted.

1234

you wish to call from memory.

Sets a frequency.

When you call an equalizer curve, its type is shown

as "User".

Sets a gain level.

Sets a Q value.

Store the present equalizer curve in memory, or

calls it from memory.

Close the Parametric Equalizer screen

Exits the Parametric Equalizer setup and returns

to the Equalizer screen.

Return

Select a frequency band you wish to adjust

Band1

—

Band4

You can adjust the following frequency bands.

60, 80, 100, 120, 160, 200, 250 Hz

315, 400, 500, 630, 800, 1k Hz

1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k Hz

5k, 6.3k, 8k, 10k, 12.5k, 16k Hz

Set a center frequency

FREQ

Set a gain

Gain

80 English

English 81

Sound Effects Menu

Zone Control

You can set the front and rear audio source.

Displaying the Zone Control

screen

Returns to the Control screen of the previous

source.

Calls the Setup Menu. (see page 47)

Calls the Sound Effects Menu.

Zone Con t r o l

Turns the Zone Function (that sets different source

sounds for front and rear speakers) On or Off.

Zone Control screen (when the Zone function is On)

When turned On,

and

are shown.

Dua l

Zone

Sets the front and rear audio source separately.

(This button appears when the Zone function is On.)

Audio

Set Up

Area

R e v e r s e

When the rear speaker sound is switched, the

audio source that is output at the AV OUTPUT

terminal is also switched to the same source.

However, if you have set the "Area" to "Reverse",

the audio source that is output at the AV OUTPUT

terminal is switched depending on the front sound

source.

SRC

F r o n t

Rear

TUNER

DVD

Zone Con t r o l

Switches the front and rear audio sources.

(This button appears when the Zone function is On.)

Use "Reverse" to change over the front and rear

audio sources.

If the zone function is turned on, the

button appears on each source control screen, with

which you can adjust the volume balance between

the front and rear sources.

DVD V I DEO

1 3 : 5 0

Audio

Set Up

Direct

SRC

SCRL

TIME

PBC REP

Title

KENWOOD

T-REP

Chap

T0:05:20

82 English

Digital Effect ^{(with the optional accessory DSP unit connected only)}

You can set up the Digital Effect.

Displaying the Digital Effect

screen

Returns to the Control screen of the previous

source.

Digital Effect

Calls the Setup Menu. (see page 47)

Calls the Sound Effects Menu.

Digital Effect screen

PCM Center

If you set to "On", a sound is output from the center

speaker.

De f e a t

O f f

PCM C e n t e r

D o l b y P r o Logi c

Audio

Turns the Dolby Pro Logic function on or off.

Set Up

B i Phant om

O f f

Turns the Bi Phantom function on or off.

If you set to "On", the signal of the center channel is

controlled so that it can be exactly positioned.

SRC

Dynam i c R a n g e

Sets up the dynamic range when the Dolby Digital

sound is used.

If you set to "On", it compresses the dynamic range

to control loud sounds.

D i g i t a l E f f e c t

The DSP unit settings return to default.

• The Dolby Pro Logic and PCM Center functions

are effective when the 2ch PCM signal is used.

• You cannot set up "Bi Phantom" when "Dolby Pro

Logic" is "Off".

• You cannot set up "PCM Center" when "Dolby Pro

Logic" is "On".

English 83

Sound Effects Menu

Position ^{(with the optional accessory DSP unit connected only)}

You can adjust the sound effects according to your listening position.

Displaying the Position screen

Returns to the Control screen of the previous

source.

Calls the Setup Menu. (see page 47)

Calls the Sound Effects Menu.

Position

Sets a listening position.

Position screen

You can select any of "Front R" (Right front), "Front

L" (Left front), "Front" (All front), "Rear" (All rear), and

"ALL" (All) positions.

Audio

Set Up

The final distance is adjusted to the total of Car

Type Set Up value (see page 50) and Position

Setup (both Position and Position Fine Control)

value.

SRC

Pos i t i on

F r o n t

Pos i t i on

84 English

English 85

Hands-Free Unit Control

GSM control

You can call the following control screens if the GSM is connected to the system.

Displaying the Control screen

Displays the Search for Phone Book screen.

(See the <Calling by Phone Book>, page 88)

Or the telephone

is called.

Adds a number to the Phone Book.

(See the <Addition to Phone Book>, page 89)

Displays the Create a Mail screen.

(See the <Creating an SMS (Short Message

Service) messages>, page 92)

GSM Control screen

AUTO

FULL

Hands Free

¹⁶KENWOOD

0123456789

Displays the SMS list.

(See the <Reading SMS (Short Message Service)

messages>, page 92)

Displays the Hands-Free Call Setup screen.

(See the <Hands Free Setup>, page 91)

Clear

Enter three phone numbers for quick dialing.

(See the <Quick Dialing>, page 91)

Return

Set Up

Enters a phone number.

(See the <When dialing>, page 87)

Clears the entered phone number.

All numbers you have entered are cleared if the

button is pressed more than 1 second.

Starts the hands-free phone call.

Displays the previously called phone number.

Ends the hands-free phone call.

Returns to the previous screen.

Displays the radio wave intensity

Displays the present Auto Response status

AUTO

When Auto Response is on:

When Auto Response is off:

Indicates the SMS registration availability

Displays the calling and called phone numbers

If you have registered a phone number in the Phone

Book, the destination person name is displayed.

For details on the hands-free phone calls, see the

Instruction Manual of KCA-HF521 GSM Hands-Free

Unit (optional accessory).

86 English

When called

When dialing

When you are called, you can use the hands-

free phone.

Originate a call by entering a phone number.

Enter a phone number

Respond to a phone call

—

Originate a call

When the telephone is called, the GSM Control

screen appears automatically.

Terminate the phone call

You can start talking when the destination responds.

Terminate the phone call

The previous screen reappears.

English 87

Hands-Free Unit Control

Phone Book List screen

Calling by Phone Book

AUTO

FULL

Phone Book L i s t

0123456789

KENWOOD

You can call a person using his/her phone

number that you have registered in the Phone

Book.

Name

E d i t

Clear

Name

Display the Search for Phone Book screen

Name

Return

Name

Scrolls the list.

The Initial Input screen appears.

Enters the destination (called party) name.

Displays the destination data edit screen.

(See the <Editing the Phone Book>, page 90)

Clears the destination if this button is touched

more than 2 seconds.

Enters the destination data and returns to the

GSM Control screen.

Returns to the GSM Control screen.

Initial Input screen

AUTO

FULL

Phone Book L i s t

Type

Select a destination you wish to call

Return

Name

Switches the character type.

Scrolls the character array display.

Displays the Phone Book beginning with the

Select a destination you wish to call

name whose first character you have touched.

Returns to the GSM Control screen.

Select the initial character of a person name

in memory

The GSM Control screen appears again. The selected

destination data is displayed.

etc.

Originate a call

The Phone Book List screen appears.

You can start talking when the destination responds.

Terminate the phone call

The previous screen reappears.

88 English

Select a memory device in which you wish

to register phone data

Addition to Phone Book

You can add a phone number to the Phone

Book.

SIM CARD

IN MEMORY

Enter a phone number you wish to register

When you select the device, the Name Edit screen

appears.

—

Name Edit screen

Start phone number registration

AUTO

FULL

₁Name Ed i t

Kenwood

Type

Clear

Device Select screen

Space

Return

AUTO

FULL

D e v i c e S e l e c t

SIM CARD

Shifts the cursor.

IN MEMORY

Switches the character type.

The digits, accent and extended code characters,

and alphabets are switched each time it is

pressed.

Return

Scrolls the keyboard display.

Enters a character.

Clears the character.

Registers a phone number in the SIM card.

All entry characters are cleared if this key is

touched more than 1 second.

Enters the entry characters.

Registers a phone number in the GSM system

itself.

Returns to the GSM Control screen.

Returns to the Device Select screen.

Enters a space.

The extended code characters are displayed only

when a cellular phone supporting the GSM

alphabets is connected.

Each of extended code characters (^, {, }, \, [, ], ¯,

|, €) occupies a two-character memory space

when registered.

Enter a name

etc.

The name has been registered.

English 89

Hands-Free Unit Control

Editing the Phone Book

You can edit data you have registered in the

Phone Book.

Select an item you wish to edit

The phone number is registered, the Edit Name

("Name Edit") screen appears.

Name

Edit Name ("Name Edit") screen

AUTO

FULL

See the <Calling by Phone Book> (see page 88) and

select an item you wish to edit on the Phone Book

List screen.

₁Name Ed i t

Kenwood

Type

AUTO

FULL

Clear⁵

Phone Book L i s t

0123456789

KENWOOD

Name

E d i t

Clear

Space

Return

Shifts the cursor.

Return

Switches the character type.

The digits, accent and extended code characters,

and alphabets are switched each time it is

pressed.

Start editing

Scrolls the keyboard display.

Enters a character.

Clears the character.

E d i t

All entry characters are cleared if this key is

touched more than 1 second.

Enters the entry characters.

The Edit Phone Number screen appears.

Returns to the Edit Phone Number ("TEL Number

Edit") screen.

Enters a space.

Edit Phone Number ("TEL Number Edit") screen

AUTO

FULL

Number Ed i t

The extended code characters are displayed only

when a cellular phone supporting the GSM

alphabets is connected.

Each of extended code characters (^, {, }, \, [, ], ¯,

|, €) occupies a two-character memory space

when registered.

0123456789

²Clear

Return

Enter a name

Enters a phone number.

etc.

Clears the input phone number.

All entry number are cleared if this key is touched

more than 1 second.

Returns to the Phone Book List screen.

Enters the phone number.

Enter a phone number

The editing completes and the Phone Book data is

updated.

—

90 English

Quick Dialing

Hands Free Setup

You can register up to 3 phone numbers for

quick dialing.

The hands-free system can be set as follows.

Display the SMS Set Up screen

To register a phone number:

Display a phone number you wish to register

Set Up

See the <Calling by Phone Book> (see page 88) and

<When dialing> (see page 87).

Hands Free Set Up screen

AUTO

FULL

Hands Free Set Up

Au t o Response Time

31 sec

MIC s e nce

Phone Vo i c e

—

Continue to touch more than 2 seconds.

To call a phone number from memory:

Right

L e f t

Book SYNC

SMS SYNC

Return

Sets an automatic response time after call

termination.

—

Adjusts the microphone sensitivity.

Sets a ringing tone output position.

"Left": Outputs the tone from the front left-hand

side speaker.

Only a phone number can be registered for

Quick Dialing. Therefore, the destination

subscriber name and others are not displayed

during dialing.

"Right": Outputs the tone from the front right-hand

side speaker.

Synchronizes the GSM with the Phone Book of

optional KCA-HF521 unit.

Synchronizes the GSM with the SMS of optional

KCA-HF521 unit.

Returns to the GSM Control screen.

The "Phone Voice" of both "Left" and "Right" can

be turned On at the same time. But they cannot

be turned Off at the same time.

English 91

Hands-Free Unit Control

Reading the SMS (Short

Message Service) messages

Creating an SMS (Short

Message Service) message

You can display messages received by the

SMS.

You can create a message to be sent by the

SMS.

Enter the destination number where you

wish to send an SMS message

Display the BOX Message List screen

—

BOX Message List screen

Display the SMS Message Input screen

AUTO

FULL

Box L i s t

0 1234567890123456

SMS Message Input screen

AUTO

FULL

Message I n p u t

Kenwood

Return

Type

Displays messages.

Scrolls the message list.

Returns to the GSM Control screen.

Clear⁶

Space

Return

Select a message you wish to display

Shifts the cursor.

Switches the character type.

The digits, accent and extended code characters,

and alphabets are switched each time it is

pressed.

The message is displayed on the Box Message

screen.

Enters a space.

Scrolls the keyboard display.

Enters a character.

BOX Message screen

AUTO

FULL

Clears the character.

Box Message

31 / 0 1 /02 2 0 :15

All entry characters are cleared if this key is

touched more than 1 second.

Sends the created message.

Returns to the GSM Control screen.

Clear

Return

Create a message

etc.

Scrolls for a single message.

Clears the message if this button is touched more

than 2 seconds.

Returns to the BOX Message List screen.

92 English

Send the message

Returns to the GSM Control screen.

The extended code characters are displayed only

when a cellular phone supporting the GSM

alphabets is connected.

Each of extended code characters (^, {, }, \, [, ], ¯,

|, €) occupies a two-character memory space

when registered.

English 93

Glossary

DVD: Digital Versatile Disc

Title number (DVD)

A type of disc which contains recording of

audio/video packaged media with high video and

audio quality, such as a movie, featuring large

recording capacity and digital signal processing

capability.

The title is the largest unit of video and audio

recorded in a DVD. It usually corresponds to a

single movie of video software or an album

(sometimes a piece of music) of music software.

The numbers assigned to individual titles are

referred to as the title numbers.

VCD: VIDEO CD

Chapter number (DVD)

A type of CD which contains the recording of

moving images. It compresses image information

by about 1/120 and audio information by about 1/6

and accommodates up to 74 minutes of recording

in a disc with the same diameter as ordinary

music CD of 12 cm.

The chapter is a section of video and audio

recorded in a DVD. A title is composed of several

chapters. The numbers assigned to individual

chapters are referred to as the chapter numbers.

Some VCDs do not have the P.B.C. compatibility

and are capable of playback only, while some are

P.B.C.-compatible and are capable of various

special playback control operations. This player

can play both of these VCDs.

Subtitles (DVD)

Some DVD discs contains the recording of more

than one subtitle language. This player allow you

to select one of the recorded subtitle languages

during playback.

MPEG: Moving Picture Expert Group (DVD, VCD)

Track number (CD, VCD)

This is an international standard for digital video

and audio compression and decompression in

media.

A track is also a section of video and audio

recorded in a disc. The numbers assigned to

individual tracks are referred to as the track

numbers.

With most of music CDs, a track is assigned to a

piece of music. However, with a VCD, the

sections of the contents do not always

correspond to the assigned tracks.

As (special) playback functions such as skipping

and programming of ordinary CDs are based on

track number data, such playback functions are

sometimes impossible with some VCDs.

Dolby Digital

This is a digital audio compression technology

developed by Dolby Laboratories. It is compatible

with 5.1-channel surround audio as well as normal

stereo (2-channel) audio and can accommodate a

large amount of audio data efficiently in a disc.

DTS

Name of a digital surround system developed by

Digital Theater Systems, Inc.

P.B.C.: Play-Back Control (VCD)

When a VIDEO CD carries "Play Back Control

capable" or similar message on the disc or jacket,

desired scenes and information can be played

back in an interactive manner using a hierarchical

structure while viewing the menu screens

displayed on the TV screen.

Top menu/menu (DVD)

Some DVDs display more than one title in a

screen. This screen is referred to as the top

menu.

The menu is the item display (menu screen) for

use in setting operations. The menu can be

recalled any time during playback to perform

settings according to the current software,

including the audio switching between Dolby

Digital and PCM, switching of language used in

the subtitles and spoken voice.

94 English

Troubleshooting Guide

Some system functions are limited to control depending on your setup.

"Multi Channel" has been set to "2/0"

or "3/0" (no rear speaker setting) on

the Speaker Set Up screen (page 51).

The rear speakers of DTA cannot be set.

The "Channel Level" of rear speakers cannot be set.

No signals can be set.

The "Equalizer" cannot be set.

The "Position" cannot be set.

The Zone Control has been turned

On (page 82).

The "Car Type Setup" value cannot be set.

The "Speaker Setup" value cannot be set.

No crossover frequency can be set.

The "Channel Level" (test signal output) cannot be set.

"Multi Channel" has been set to "2/0"

or "2/2" (no center speaker setting) on

the Speaker Set Up screen (page 51).

The center speaker for DTA cannot be set.

The "Channel Level" of the center speaker cannot be set.

The subwoofer of DTA cannot be set.

"Sub Woofer" has been set to "Off" on

the Speaker Set Up screen (page 51).

The "Channel Level" of the subwoofer cannot be set.

English 95

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or

miswiring. Before calling service, first check the following table for possible problems.

General

■

The power does not turn on.

• The fuse has blown.

• After checking for short circuits in the wires, replace the

fuse with one having the same rating.

The desired source is NOT selected although you pressed the SRC button.

• A non-connected source is not selected. See

<INSTALLATION MANUAL> and connect the unit correctly.

• Press the reset button (see page 4).

• An optional unit required to listen to each source is

not connected yet.

• The RESET button is not pressed yet although the

optional unit has been connected to the system.

• The "O-N" switch of the optional unit is at the "O"

position.

• Set the "O-N" switch to the "N" position.

• Use a disc changer supported by the system (see page 4).

• A disc changer not supported by the system is used.

Nothing happens when the buttons are pressed.

• Press the reset button on the unit (see page 4).

• The computer chip in the unit is not functioning

normally.

No television/video image appears.

• Make proper connections according to <INSTALLATION

MANUAL>.

• The unit is not connected to the parking brake

detection switch.

• For safety reasons no television/video images are

displayed while the vehicle is moving. Engaging the

parking brake will cause images to be displayed.

• The parking brake is not engaged.

The screen is dark.

• If the temperature of the monitor unit drops, the screen

may appear darker when power is first turned on due to

the characteristics of a liquid crystal panel. Wait a while

after turning power on for the temperature to rise. Normal

brightness will return.

• The unit is in a location where temperature is low.

The screen does not darken when the vehicle’s lights are turned on.

• When the unit is set to auto dimmer, it is not linked to the

vehicle's light switch.

• The unit is set to auto dimmer.

• Make proper connections according to <INSTALLATION

MANUAL>.

• The illumination wire has not been connected. (If

manual dimmer is set)

AM/FM radio reception is poor and/or there is noise.

• Separate the two antennas as far as possible.

• Turn off the main unit.

• The TV antenna and vehicle‘s radio antenna are too

close.

The remote controller does not operate.

• Switch the remote control mode selector according to the

source you select (see page 10).

• The remote control mode selector is not set

correctly.

96 English

No sound can be heard, or the volume is low.

• Turn off Attenuator.

• Attenuator is turned on.

• Reset the fader and/or balance settings.

• The fader or balance settings are set all the way to

one side.

• Reconnect the input/output wires or the wiring harness

correctly. See the section on <INSTALLATION MANUAL>.

• The input/output wires or wiring harness are

connected incorrectly.

The sound quality is poor or distorted.

• Check the speaker wiring.

• One of the speaker wires is being pinched by a

screw in the car.

• Reconnect the speaker wires so that each output terminal

is connected to a different speaker.

• The speakers are not wired correctly.

Radio reception is poor.

• Pull the antenna out all the way.

• The car antenna is not extended.

• Connect the wire correctly, referring to the section on

<INSTALLATION MANUAL>.

• The antenna control wire is not connected.

The memory is erased when the ignition is turned off.

• The battery wire has not been connected to the

proper terminal.

• The ignition and battery wire are incorrectly

connected.

• Connect the wire correctly, referring to the section on

<INSTALLATION MANUAL>.

• Connect the wire correctly, referring to the section on

<INSTALLATION MANUAL>.

The TEL mute function does not work.

• Connect the wire correctly, referring to the section on

<INSTALLATION MANUAL>.

• The TEL mute wire is not connected properly.

The TEL mute function turns on even though the TEL mute wire is not connected.

• Pull the TEL mute wire away from the metal part of the

car.

• The TEL mute wire is touching a metal part of the

car.

The sound/picture skips on a DVD/VCD/CD.

• Clean the disc, referring to the section on <Disc cleaning>

(see page 6).

• The disc is scratched or dirty.

A track will not play.

• Turn off random play.

• Random play has been selected.

A VCD cannot be played using menus.

• The VCD disc being played is not compatible with

P.B.C.

• Menu playback is available only with VCD discs recorded

with P.B.C.

The subtitle is not displayed.

• The subtitle cannot be displayed when the DVD disc being

played does not contain the recording of subtitles.

• The DVD disc being played does not contain the

recording of subtitles.

The voice (or subtitle) language cannot be changed.

• The voice (or subtitle) language cannot be changed when

the DVD disc being played does not contain the recording

of more than one voice (or subtitle) language.

• The DVD disc being played does not contain the

recording of more than one audio (or subtitle)

language.

English 97

Troubleshooting Guide

The viewing angle cannot be changed.

• The viewing angle cannot be changed when the DVD disc

being played does not contain the recording of more than

one angle.

• The DVD disc being played does not contain the

recording of more than one angle.

• More than one viewing angle may be recorded only in

limited sections in a disc.

• You are attempting to switch the angle in a DVD

section where more than one angle is not recorded.

Playback will not start even after a title is selected.

• Check the viewing restriction level (RATING) setting.

• A viewing restriction (RATING) has been set for the

disc.

The voice or subtitle language selected in the initial setting is not played.

• Use a DVD disc containing the recording of the selected

voice or subtitle language.

• The DVD disc being played does not contain the

recording of the selected voice or subtitle language.

Disc source

■

The disc control mode cannot be selected.

• Connect the wire to the disc changer input terminal on the

unit.

• No wire has been connected to the disc changer

input terminal on the unit.

The specified disc does not play, but another one plays instead.

• Clean the CD.

• The specified CD is quite dirty.

• The CD is upside-down.

• The disc is loaded in a different slot from that

specified.

• Load the CD with the labeled side up.

• Eject the disc magazine and check the number for the

specified disc.

• Try another disc instead.

• The disc is severely scratched.

The sound skips.

• Something is touching the disc changer.

• The CD is scratched or dirty.

• Remove whatever is touching it.

• If skipping happens at the same place when the car is

stopped, something with the CD is wrong. Clean the CD.

The display shows that the changer is being played, but no sound can be heard.

• The computer chip in the unit is not functioning

normally.

• Press the reset button on the unit (see page 4).

The specified track will not play.

• Turn off random play or magazine random play.

• Random play or magazine random play has been

selected.

Track repeat, disc repeat, track scan, disc scan, random play, and magazine random play start by themselves.

• The settings for these functions remain on until the

setting to off or the disc ejected, even if the power is

turned off or the source changed.

• The setting is not cancelled.

Can’t remove disc.

• The disc can only be removed within 10 minutes of the

ACC switch being turned OFF. If more than 10 minutes

has elapsed, turn the ACC switch ON again and press the

Eject button.

• The cause is that more than 10 minutes has elapsed

since the vehicle ACC switch was turned OFF.

98 English

MP3/WMA source

■

Cannot play an MP3/WMA.

• The media is scratched or dirty.

• Clean the media, referring to the CD cleaning of the

section on <About discs> (see page 6).

The sound skips when an MP3/WMA is being played.

• The media is scratched or dirty.

• The recording condition is bad.

• Clean the media, referring to the CD cleaning of the

section on <About discs> (see page 6).

• Record the media again or use another media.

The MP3/WMA track time isn’t displayed correctly.

• ---

• There are times when it isn’t displayed correctly according

to the MP3/WMA recording conditions.

Can’t display the ID3 tag information correctly.

• Record is not made in conformity with the ID3 tag

version 1.x.

• Record in conformity with the ID3 tag version 1.x.

Also, the display may be incorrect if an MP3 file uses the

ID3 tag v1.x standard and if this standard has been

expanded after production of the machine software.

The following messages are displayed when certain problems are occurring in your system. Take

the recommended actions.

Hot Error

The protective circuit in the unit activates when the temperature inside the unit exceeds 60°C

(140°F), stopping all operation.

]

Cool down the unit by opening the windows or turning on the air conditioner. As the

temperature falls below 60°C (140°F), the disc will start playing again.

Hold Error

Mecha Error

The protective circuit in the unit activates when the temperature inside the automatic disc

changer exceeds 60°C (140°F), stopping all operation.

]

Cool down the unit by opening the windows or turning on the air conditioner. As the

temperature falls below 60°C (140°F), the disc will start playing again.

The disc player is malfunctioning.

]

Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continues

blinking or the disc cannot be ejected.

Disc Error

Read Error

The unplayable discs is inserted.

The disc is upside-down.

]

Load the disc with the labeled side up.

The disc is quite dirty.

]

Clean the disc, referring to the section on <Disc cleaning> (see page 6).

Region code Error

Parental level Error

Error 07 — 67

The DVD software encoded for other region code.

The parental level is set to high levels.

The unit is malfunctioning for some reason.

]

Press the reset button on the unit. If the "Error ##" code does not disappear, consult your

nearest service center.

English 99

Specifications

Specifications subject to change without notice.

Monitor section

Video section

Picture size................................................6.4 inches wide

143.6(W)×77.1(H)mm

Color system of external video input ................NTSC/PAL

External video input level (RCA jacks) ..............1Vp-p/75Ω

External audio max input level (RCA jacks) ..........1V/22kΩ

Analog RGB input ..........................................0.7Vp-p/75Ω

Display system ........................Transparent TN LCD panel

Drive system..............................TFT active matrix system

Number of pixels....................336,960 (480H×234V×RGB)

Effective pixels ......................................................99.99%

Pixel arrangement......................RGB striped arrangement

Back lighting ....................Cold Cathode Fluorescent Tube

Audio section

Maximum Power (Front&Rear) ..............................50W×4

Output power (Front&Rear)

(DIN 45324, +B=14.4V) ......................................30W×4

Preout level (V) ....................................................2V/10kΩ

Preout impedance ..................................................≤ 600Ω

Tone action

Bass........................................................100 Hz 10 dB

Middle ......................................................1 kHz 10 dB

Treble......................................................10 kHz 10 dB

DVD section

D/A Converter ............................................................24Bit

Decoder ............Linear PCM/Dolby digital/dts/MP3/WMA

Wow & Flutter ............................Below Measurable Limit

Frequency response

(Sampling frequency;96k) ........................20~44,000Hz

(Sampling frequency;48k) ........................20~22,000Hz

(Sampling frequency;44.1k) ......................20~20,000Hz

Total harmonic distortion (1k) ................................0.010%

Signal to Noise ratio................................100dB (DVD 96k)

Dynamic range........................................100dB (DVD 96k)

DISC Format........................DVD-Video/VIDEO-CD/CD-DA

Sampling frequency........................44.1kHz/48kHz, 96kHz

Quantifying bit number ....................................16/20/24bit

General

Operating voltage....................................14.4V (11V~16V)

Current consumption ..................................................15A

Dimensions (W×H×D) ..............182mm×112mm×163mm

Operational temperature range ......................-10°C~60°C

Storage temperature range ............................-20°C~85°C

Weight ......................................................................2.8kg

FM Tuner section

Frequency range (50kHz)..........................87.5~108.0MHz

Usable sensitivity (S/N=26dB) ..........................0.7µV/75Ω

Quieting sensitivity (S/N=46dB) ........................1.6µV/75Ω

Frequency response ( 3.0dB) ......................30Hz~15kHz

S/N (dB) (MONO) ......................................................66dB

Selectivity ( 400kHz)..............................................≥ 80dB

Stereo separation............................................39dB (1kHz)

LW Tuner section

Frequency range (9kHz) ..........................153kHz~281kHz

Usable sensitivity ....................................................28dBµ

MW Tuner section

Frequency range (9kHz) ........................531kHz~1611kHz

Usable sensitivity ....................................................28dBµ

Although the effective pixels for the liquid crystal panel is given as 99.99% or more, 0.01% of pixels may not light or may

light incorrectly.

100 English

The marking of products using lasers (Except for some areas)

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and says that the component uses laser beams that have been classified as

Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous

radiation outside the unit.

is a trademark of DVD Format/Logo Licensing Corporation registered in the U.S., Japan and other countries.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual

property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home

and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is

prohibited.

Manufactured under license from Dolby Laboratories.

"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

"DTS" and "DTS 2.0 + Digital Out" are trademarks of Digital Theater Systems, Inc.

English 101

Reliable i702 User Manual
Panasonic HHR120AA User Manual
Panasonic Cordless Phone With Answering Machine KXTG7645M User Manual
Panasonic AW RP400N User Manual
Oster Blender 139846 User Manual
MTX Audio MTX Thunder Axe Separates TX4001 User Manual
Mercedes Benz Comand 6515 6786 13 User Manual
Magnadyne S DV424 User Manual
Liebherr WS14300 User Manual
KitchenAid KFP720WH0 User Manual