Kenwood Car Stereo System KDC U7056BTL User Manual

KDC-U7056DAB  
KDC-U7056BT  
KDC-U7056BTL  
CQDu-RiEcCkEIVSERtart Guide  
© 2012 JVC KENWOOD Corporation  
B59-2188-10/01 (M)  
• To display characters in the following  
language, additional setting is required.  
KDC-U7056DAB KDC-U7056BT  
- Chinese  
How to reset your unit  
If the unit fails to operate properly, press the  
Reset button. The unit returns to the factory  
settings.  
Refer to “Chineseof <12-5. Initial  
Reset button  
settings>.  
KDC-U7056BTL  
- Arabic  
- Persian  
- Thai  
Refer to “TAG Languageof <12-5. Initial  
settings>.  
About the discs used with this unit  
• This unit can only play the CDs with  
.
• The following discs cannot be used:  
- A disc that is not round  
- A disc with coloring on the recording  
surface or a disc that is dirty  
- A recordable/rewritable disc that has  
not been finalized (For the finalization  
process, refer to the instruction manual  
that came with your disc writing  
software or your disc recorder.)  
- An 8 cm (3 inch) disc (An attempt  
to insert using an adapter can cause  
malfunction.)  
The illustrations of the display and panel appearing  
in this manual are examples used to explain more  
clearly how the controls are used. Therefore, what  
appears on the display in the illustrations may differ  
from what appears on the display on the actual  
equipment, and some of the images on the display  
may be inapplicable.  
Handling discs  
! CAUTION  
• Do not touch the recording surface of  
the disc.  
• Keep battery out of reach of children  
and in original package until ready to  
use. Dispose of used batteries promptly.  
If swallowed, contact a physician  
immediately.  
• Do not stick tape etc. on the disc, or use a  
disc with tape stuck on it.  
• Do not use any accessories for the disc.  
• Do not use any solvents to clean discs.  
Use a dry silicon or soft cloth.  
• Clean the disc by moving the cloth  
outward from the center of the disc.  
• When removing a disc from this unit, pull  
it out horizontally.  
• If the center hole or outside rim of a disc  
has burrs, remove them before inserting  
a disc.  
• Do not leave the battery near fire or  
under direct sunlight. A fire, explosion  
or excessive heat generation may result.  
• Do not set the remote control in hot  
places such as on the dashboard.  
• The Lithium battery is in danger of  
explosion if replaced incorrectly.  
Replace it only with the same or  
equivalent type.  
|
English  
3
Appendix  
Preparations  
About Audio file  
• Playable Audio files  
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma),  
WAV (.wav) of USB device  
• Playable disc media  
CD-R/RW/ROM  
• Playable disc file formats  
ISO 9660 Level 1/2, Joliet, Long file name.  
• Playable USB devices  
USB mass storage class  
• Playable USB device file systems  
FAT12, FAT16, FAT32  
The online manual about  
audio files is put on the site,  
Before using this unit for the first  
time  
When this unit is first turned on, the  
interactive menu appears for setting the  
interface language and demonstration  
mode. This menu disappears when no  
action is taken for 15 seconds.  
Models of iPods/iPhones that can  
be connected to this unit  
Made for  
• iPod touch (4th generation)  
• iPod touch (3rd generation)  
• iPod touch (2nd generation)  
• iPod touch (1st generation)  
• iPod classic  
1
KDC-U7056BTL only:  
Select the interface language to display  
the menu items of the Function setting,  
from English, Arabic, and Persian.  
Turn [Control] knob to select the  
language, and then press [Control] knob.  
• iPod with video  
• iPod nano (6th generation)  
• iPod nano (5th generation)  
• iPod nano (4th generation)  
• iPod nano (3rd generation)  
• iPod nano (2nd generation)  
• iPod nano (1st generation)  
• iPhone 4S  
• iPhone 4  
• iPhone 3GS  
• iPhone 3G  
• iPhone  
2
KDC-U7056BTL only:  
If you selected English in step 1, select  
the language to display the audio file  
information, from English and Thai.  
(Arabic or Persian is automatically  
selected if you selected Persian or Arabic  
in step 1.)  
3 Press [Control] knob when the message  
To cancel DEMO Press the volume knob”  
appears.  
For information on the compatibility with  
iPod/iPhone software, visit www.kenwood.  
com/cs/ce/ipod/.  
4 Turn [Control] knob to select “YES, and  
then press [Control] knob.  
The interface language and  
demonstration mode can also be set  
with the Function setting. Refer to <12-  
4. Demonstration mode setting> in  
Instruction manual  
|
4
Quick Start Guide  
[Control] knob (Volume knob)  
Release  
1 6  
/ ]  
[
Adjusting the clock  
Detaching/ Attaching the faceplate  
1
Press [Control] knob to enter the  
Function setting mode.  
The item can be selected and  
determined as follows.  
”SettingsÁ “Clock & DateÁ “Clock  
Adjust”  
Turn [Control] knob to select the item,  
and press [Control] knob.  
Press the  
Release button.  
2 Turn [Control] knob to adjust the hour,  
and then press [Control] knob.  
3 Turn [Control] knob to adjust the  
minute, and then press [Control] knob.  
4 Press and hold [1/6] to exits the  
Function setting mode.  
!
• Remove the faceplate at once after  
pressing the Release button; otherwise it  
can fall down due to vibration.  
• The faceplate is a precision component of  
the unit and can be damaged by shocks  
or jolts.  
• Keep the faceplate in its case while  
detached.  
• Do not place the faceplate (and case) in  
areas exposed to direct sunlight, excessive  
heat or humidity. Also avoid places with  
too much dust or the possibility of water  
splashing.  
|
English  
5
General operations  
USB terminal  
[SRC] [Control] knob (Volume knob)  
Auxiliary input  
Power  
To turn the power ON, press [SRC].  
To turn the power OFF, press and hold  
Bluetooth audio  
CD[1]  
Auxiliary Input  
“BT AUDIO”  
“CD”  
“AUX”  
[SRC].  
[1] This source can be selected only when it can  
be played.  
[2] Function of KDC-U7056DAB.  
[3] Function of KDC-U7056BT.  
Source selection  
Pressing [SRC] repeatedly switches  
among sources.  
Volume  
Source  
Display  
Turn [Control] knob to adjust the sound  
Standby  
“STANDBY”  
“DIGITAL RADIO”  
“TUNER”  
volume.  
Digital radio[2]  
USB terminal  
Tuner  
A USB device or iPod can be connected.  
The CA-U1EX (Max. 500mA) or KCA-iP102  
(optional accessories) is recommended  
to connect a USB device or iPod.  
USB device connected to front USB  
terminal  
USB device connected to rear USB  
terminal  
“USB (FRONT)”  
“USB (REAR)”  
iPod connected to front USB terminal[1] “iPod (FRONT)”  
iPod connected to rear USB terminal[1] “iPod (REAR)”  
Pandora® of iPod connected to front “Pandora  
Auxiliary input  
A portable audio device can be  
connected with a stereo mini-plug (3.5  
mm ø).  
USB terminal[1][2][3]  
(FRONT)”  
Pandora of iPod connected to rear USB “Pandora  
terminal[1][2][3]  
(REAR)”  
Pandora of device connected via  
Bluetooth[1][2][3]  
“Pandora”  
aha™ of iPod connected to front USB “aha (FRONT)”  
terminal[1]  
aha™ of iPod connected to rear USB “aha (REAR)”  
terminal[1]  
aha™ of device connected via  
Bluetooth[1]  
“aha”  
|
6
Quick Start Guide  
Playing music (CD/USB/iPod)  
CA-U1EX[1]  
Disc slot  
G
[
]
Disc slot cover  
[Control] knob  
KCA-iP102[1]  
REAR USB indicator  
USB Terminal  
1 6  
E F R S  
]
[
/
]
[
/
]
[
/
Playing a disc  
Pause and play a song (track or  
Open the Disc slot cover upward.  
Insert a disc in the Disc slot.  
When it is inserted, the source is  
switched automatically and playback  
starts.  
file)  
Press and hold [1/6].  
Music search  
You can search for the song you want to  
play.  
Close the Disc slot cover.  
1
Press [1/6].  
Playing a USB device/ iPod  
Connect a USB device or iPod to the USB  
terminal as shown above.  
When it is connected, the source is  
switched automatically and playback  
starts.  
You can connect the iPod or USB device  
to either one of the USB terminals  
provided at the front and rear of this unit.  
If you connect it to the rear USB terminal,  
2 Search for a song.  
Operation type  
Operation  
Turn [Control] knob.  
Press [Control] knob.  
Selecting items  
Determining selection  
Returning to previous item Press [1/6].  
To cancel music search in audio files or  
iPod, Press and hold [1/6].  
Ejecting disc  
the “REAR USBindicator stays lit.  
[1] optional accessories  
Open the Disc slot cover upward, and  
press [G].  
Selecting an audio file folder  
Press [R] or [S].  
Removing USB device/ iPod  
Switch to a source other than USB,  
iPod, Pandora, and Aha Radio, and then  
remove the USB device.  
Selecting a song (track or file)  
Press [E] or [F].  
Data contained in the USB device/ iPod  
may be damaged if you remove it when  
it is used as the active source.  
Fast-forwarding or fast-  
backwarding a song (track or file)  
Press and hold [E] or [F].  
|
English  
7
Listening to the radio/Digital radio  
[SRC]  
[Control] knob  
[
R
]
1 6  
E F  
]
[
/
]
[
/
4 Turn [Control] knob to select preset  
number (FM/ Digital Radio: “118,  
AM: “16”), and then press and hold  
[Control] knob.  
Selecting a tuner source  
Press [SRC] to select “TUNERor “DIGITAL  
RADIO(KDC-U7056DAB only). Refer to  
<Source selection> (page 6).  
Recalling the stations in the  
memory  
Selecting a band (FM or AM)  
(Tuner only)  
Press [R].  
1
Press [R] to select a band. (Tuner only)  
2 Press [1/6].  
Selecting a station/ service  
Press [E] or [F].  
3 Turn [Control] knob to select a preset  
number (FM/ Digital Radio: “118, AM:  
“16”), and then press [Control] knob.  
In the Mix Station preset mode, band  
names of tuner sources are displayed as  
follows:  
The seek mode can be changed. Refer to  
<9-5. Tuner setting> or <10-1. Listening  
to the Digital Radio> in Instruction  
manual  
Station preset memory  
FM: FM broadcast station  
AM: AM broadcast station  
1
Press [R] to select a band. (Tuner only)  
2 Press [E] or [F] to select the  
station/ service you want to save in the  
station preset memory.  
DR: Digital Radio service  
3 “TUNER”: Press [1/6].  
“DIGITAL RADIO”: Press [1/6] twice.  
Press [1/6] again to enter the Mix  
Station preset mode. In this mode,  
different bands and tuner sources (FM,  
AM, Digital Radio etc.) can be saved  
in the same preset layer, which allows  
you to recall a desired station without  
switching between bands and/or tuner  
sources. Maximum of 6 stations can be  
preset in the Mix Station preset mode.  
|
8
Quick Start Guide  
Hands-free phoning  
[Control] knob  
Ú
[
]
Dialing a number in the phone  
Pairing a Bluetooth device  
You can pairing your Bluetooth device in  
this unit.  
book  
Dial the phone number in the phone book  
of your cell phone.  
1
Operate the Bluetooth device to request  
this unit for connection.  
If the phone book has not been  
downloaded to this unit, operate the cell  
phone to download it.  
The name of this unit (“KDC-####”)  
appears on the Bluetooth device.  
“Press the volume knobappears.  
1
Press [Ú].  
2 Press [Control] knob.  
2 Turn [Control] knob to select “Phone  
Connection to your Bluetooth device  
starts, “Pairing Successappears a while  
later, and then the previous source is  
selected.  
Book, and then press [Control] knob.  
3 Turn [Control] knob to select a name,  
and then press [Control] knob.  
4 Turn [Control] knob to select a phone  
When registration of your cell phone is  
completed, the phone book of the cell  
phone is automatically downloaded  
to this unit. (If the phone book has not  
been downloaded to this unit, operate  
the cell phone to download it.)  
number.  
5 Press [Ú].  
Answering a phone call  
Press [Ú].  
Disconnecting a call  
Press [Ú].  
|
English  
9
Before installation  
you connect the + connector of the left  
speaker to a front output terminal, do  
not connect the - connector to a rear  
output terminal.  
• Connect the speaker wires correctly to the  
corresponding terminals. The unit may  
be damaged or fail to work if you share  
the - wires or ground them to any metal  
part in the car.  
# WARNING  
• The unit can only be installed in a car with  
a 12V DC power supply, negative ground.  
• If you connect the ignition wire (red)  
and the battery wire (yellow) to the car  
chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always  
connect those wires to the power source  
running through the fuse box.  
• Do not use your own screws. Use only  
the supplied screws. Using wrong screws,  
could damage the unit.  
!
CAUTION  
• Use the power harness enclosed with this  
unit for connecting power. Using a power  
harness enclosed with other models can  
cause malfunction.  
• Install this unit in the console of your  
vehicle.  
• Do not touch the metal parts of this unit  
during and shortly after use of the unit.  
Metal parts such as the heat sink and  
enclosure become hot.  
• Mounting and wiring this product  
requires skills and experience. For safety’s  
sake, leave the mounting and wiring work  
to professionals.  
• If your car’s ignition key switch does  
not have an ACC position, connect the  
ignition wires to a power source that can  
be turned on and off with the ignition  
key. If you connect the ignition wires to  
a constant-voltage power source, as with  
battery wires, the battery may die.  
• If the console has a lid, make sure to  
install the unit so that the faceplate will  
not hit the lid when it is closed or opened.  
• After the installing the unit, check  
whether the brake lamps, blinkers, wipers,  
etc. on the car are working properly.  
• Mount the unit so that the mounting  
angle is 30° or less.  
• If you experience any problem during  
installation, consult your Kenwood dealer.  
• Disconnect the battery’s negative terminal  
before installing the unit.  
• Reception may become poor if there are  
metal objects near the Bluetooth antenna.  
• Insulate unconnected wires with vinyl  
tape or other similar materials. To prevent  
a short circuit, do not remove the caps on  
the ends of the unconnected wires and  
terminals.  
Bluetooth antenna unit  
• Be sure to ground this unit to the car’s  
chassis again after mounting.  
• If the fuse blows, first make sure the wires  
are not touching other parts to cause a  
short circuit, and then replace the old fuse  
with one with a new the same rating.  
• When connecting only two speakers,  
connect the connectors either to both  
of the front output terminals or to both  
of the rear output terminals (do not mix  
front and rear terminals). For example, if  
|
10 Quick Start Guide  
KDC-U7056DAB  
3
• This unit has the cooling fan to decrease  
the internal temperature. Do not mount  
the unit in a place where the cooling  
fan of the unit are blocked. Blocking  
these openings will inhibit the cooling  
of the internal temperature and result in  
malfunction.  
.....4  
.....4  
4
Cooling fan  
5
For Good Reception  
.....1 (3m)  
.....1  
To assure good reception, note the  
following:  
6[1]  
7[1]  
8[1]  
• Communicate with the cell phone within  
the line-of-sight distance of 10 m (30  
ft). The communication range becomes  
shorter depending on the surrounding  
environment. The communication  
range also becomes shorter when there  
is an obstacle between this unit and  
the cell phone. The above maximum  
communication range (10 m) is not  
always assured.  
.....1  
• A broadcast station or walkie-talkie  
located nearby can interfere with  
communication due to a too strong  
signal.  
.....3  
Installation accessories  
9[1]  
1
.....1  
.....1  
[1] KDC-U7056DAB only  
2
.....2  
|
English 11  
Connecting wires to terminals  
Rear output  
R
L
Front output  
Subwoofer output  
Fuse (10A)  
FM/AM antenna input  
R
L
Digital radio antenna  
(Accessory7)  
(KDC-U7056DAB only)  
Wiring harness  
(Accessory1)  
Microphone (Accessory5)  
(KDC-U7056BT/  
KDC-U7056BTL only)  
White  
White/Black  
To front left speaker  
To front right speaker  
Gray  
Gray/Black  
Green  
Green/Black  
Purple  
To rear left speaker  
To rear right speaker  
Purple/Black  
<
Ignition key  
switch  
• Speaker Impedance: 4 – 8 Ω  
Car fuse  
box  
ACC  
Red (Ignition wire)  
Car fuse box  
(Main fuse)  
Yellow (Battery wire)  
Black (Ground wire) · (To car chassis)  
+
Battery  
KDC-U7056DAB only  
|
12 Quick Start Guide  
USB connector (0.8m)  
To USB device.  
USB maximum power supply current  
: DC 5 V = 1 A  
Microphone (Accessory5)  
(KDC-U7056DAB only)  
If no connections are made, do not let the wire come out from  
the tab.  
Blue/White  
(Power control wire)  
When using the optional power amplifier, connect  
this wire to its power control terminal.  
P.CONT  
Depending on what antenna you are using, connect  
either to the control terminal of the motor antenna,  
or to the power terminal for the booster amplifier of  
the film-type or short pole type antenna.  
(Max. 300mA, 12V)  
Blue (Antenna control wire)  
ANT.  
CONT  
Brown (Mute control wire)  
When connecting to the Kenwood navigation  
system: Refer to your navigation manual.  
MUTE  
Orange/ White  
(Dimmer control wire)  
To car light control switch.  
ILLUMI  
Light Blue/ Yellow  
(Steering remote control wire)  
To use the steering wheel remote control feature,  
an exclusive remote adapter (not supplied) that  
matches your car is required.  
REMOTE CONT  
STEERING WHEEL  
REMOTE INPUT  
|
English 13  
3 way speaker system setup  
Connect the speaker wires  
Tweeter output  
R
L
Mid Range output  
Woofer output  
R
L
Wiring harness  
(Accessory1)  
White  
White/Black  
Gray  
To MID Range left speaker  
To MID Range right speaker  
Gray/Black  
Green  
Green/Black  
Purple  
To left Tweeter  
To right Tweeter  
Purple/Black  
Blue/White  
(Power control wire)  
When using the optional power amplifier,  
connect this wire to its power control  
terminal.  
P.CONT  
If no connections are made, do not  
let the wire come out from the tab.  
¤
Select a crossover mode according to  
how the speakers are connected. Refer  
to <2-Way/3-Way Crossover Setting>  
(next page).  
For how to connect speaker wires  
If you select a wrong mode:  
to terminals other than speaker  
terminals and Preout terminals, refer  
to <Connecting wires to terminals>  
(page 12).  
• The speakers can break.  
• The output sound level may be  
extremely low.  
|
14 Quick Start Guide  
2-Way/3-Way Crossover Setting  
Select a crossover mode 2-way or 3-way  
according to how the speakers are  
connected.  
1
Press the [SRC] to select “STANDBY.  
2 Pressing down the [S] and [E]s for at  
least 3 seconds, allows you to enter the  
2-way/3-way crossover setting mode.  
3 The currently selected crossover mode  
is displayed.  
To change it, turn [Control] knob to  
select “YES, and then press [Control]  
knob.  
4 A confirmation screen appears.  
If you are sure you want to change the  
crossover mode, turn the [Control]  
knob to select “YES, and then press the  
[Control] knob.  
5 The newly selected crossover mode is  
displayed, canceling the 2-way/3-way  
crossover setting mode.  
|
English 15  
Installing/Removing the unit  
Non-Japanese cars  
Removing the trim plate  
1
Engage the catch pins on the extraction  
key (Accessory2) and release the two  
locks on the upper part of frame.  
Lift up and pull the frame forward as  
shown in the figure.  
Catch  
Lock  
Bend the tabs of the mounting sleeve  
with a screwdriver or the like and  
attach it in place.  
Accessory2  
<
2
When the upper part of frame is  
removed, remove the lower part of frame.  
• Make sure that the unit is installed  
securely in place. If the unit is unstable, it  
may malfunction (for example, the sound  
may skip).  
<
• The frame can be removed from the  
bottom side in the same manner.  
Japanese cars  
1
Remove the trim plate with reference to  
<Removing the trim plate>.  
Removing the unit  
Remove the trim plate with reference to  
<Removing the trim plate>.  
1
2 Align the holes in the unit (two locations  
on each side) with the vehicle mounting  
bracket and secure the unit with the  
accessory screws.  
2 Remove the faceplate.  
3 Insert the two extraction keys  
(Accessory2) deeply into the slots on  
both sides as shown.  
4 Lower the extraction key toward the  
bottom, and then pull out the unit  
halfway while pressing the extraction key  
towards the inside.  
Accessory2  
3
4
8 mm  
MAX.  
8mm  
MAX.  
ø5mm  
ø5mm  
!
• Be careful to avoid injury from the catch  
5pPinusllothnethuenietxatlrlatchteiownakyeyo.ut with your  
hands, being careful not to drop it.  
|
16 Quick Start Guide  
KDC-U7056DAB only  
Installing the  
Microphone unit  
Installing the Digital  
radio antenna  
!
CAUTION  
1
Check the installation position of the  
microphone (Accessory 5).  
• This film antenna is exclusively for use  
inside the vehicle.  
2 Clean the installation surface.  
• Do not install at the following locations:  
- Where it may block driver’s view  
- Where it may obstruct operation of  
safety devices such as air bags  
- On movable glass surface such as rear  
hatch  
• Signal strength will decrease at the  
following locations:  
- On IR reflecting glass or where covered  
with mirror type glass film  
3 Install the microphone.  
4 Lay the cable up to the unit with it  
secured at several positions using tape  
or the like.  
<
• Install the microphone as far as possible  
from the cell phone.  
- Where it overlaps with genuine radio  
antenna (pattern)  
Accessory5  
- Where it overlaps with window heating  
wires  
- At side of vehicle (e.g. door, front  
quarter window)  
- On rear window  
- When glass that blocks radio signals  
(e.g. IR reflecting glass, thermal  
insulation glass) is used  
- Reception may decrease due to noise  
when windshield wiper, air conditioner,  
or motor is turned on.  
Fix the cable with a commercial item of tape.  
- Reception may decrease depending on  
the direction of the broadcast station  
with respect to the vehicle (antenna).  
• Be sure to check the installation location  
of film antenna (Accessory 6) before  
installing. Film antenna cannot be  
re-pasted.  
Remove the separator of  
the microphone, and stick  
the microphone to the  
place shown above.  
• Thoroughly wipe oil and dirt from the  
pasting surface with the included cleaner  
(Accessory 9).  
• Do not bend or damage the film antenna  
(Accessory 6).  
Adjust the direction of the  
microphone to the driver.  
• Warm the pasting surface by turning on  
the heater for example, before applying.  
• It may not be possible to install on some  
type of vehicle.  
• Check the cable routing of the film  
antenna (Accessory 6) and amplifier  
(Accessory 7) before pasting.  
|
English 17  
KDC-U7056DAB only  
Installing the Digital radio antenna  
Installation overview  
Determining the antenna  
installation location  
When installing the antenna on the  
left side  
Accessory67  
Front pillar  
150 mm  
Earth sheet  
Antenna cable (3.5 m)  
70 mm*  
• The antenna should be installed on the  
passenger side for safety.  
Accessory6  
• Use cord clamper (Accessory 8) to  
secure the antenna to the pillar at several  
locations.  
• The direction of the antenna film  
(Accessory 6) changes depending on  
whether the film antenna is installed on  
the right side or left side.  
Accessory7  
When installing the antenna on the  
right side  
Front pillar  
Accessory7  
• Separate the antenna film (Accessory 6)  
from the ceramic line (black part) at the  
top of the front glass by 150 mm.  
Also, place it about 70 mm inside the  
ceramic line at the side end of the front  
glass. (where the earth sheet of the  
amplifier can be pasted on the metal part  
of the front pillar)  
Earth sheet  
150 mm  
Accessory6  
• Separate from other antennas by at least  
100 mm.  
70 mm*  
• Do not paste the amplifier (Accessory 7)  
on the ceramic line (black part) around  
the front glass. Because there is not  
enough adhesion.  
*Where the earth sheet of amplifier unit  
(Accessory 7) can be pasted on the metal  
part of the front pillar.  
|
18 Quick Start Guide  
5 After pasting, rub the element in the  
glass surface in the direction of the arrow  
shown in the figure to bond it.  
Antenna Installation  
1
Check the installation location.  
2 Clean the area where antenna film  
(Accessory 6), amplifier unit (Accessory  
7), and earth sheet are pasted with the  
included cleaner (Accessory 9).  
The coating on the metal surface need  
not be removed.  
• Wait until the glass surface is  
completely dry before pasting.  
• If the glass surface is cold, such as  
during winter, warm it with defroster or  
dryer.  
3 Remove the separator (tag I) of antenna  
film horizontally and paste the antenna  
on the front glass.  
6 Remove the application film (tag III).  
• Do not touch the feeder terminal of  
the element. Also, do not apply any  
glass cleaner.  
Feeder terminal  
7 Match the protrusion of the amplifier  
with the 5 on the antenna film and  
paste.  
• Do not touch the feeder terminal or  
the pasting surface (adhesive side) of  
the amplifier.  
• Remove the separator gently.  
• Do not touch the pasting surface  
(adhesive side) of the antenna film.  
4 Remove the separator (tag II) of antenna  
film vertically and paste the antenna  
gently while applying pressure.  
When installing the antenna on the  
right side  
Match the protrusion with 5  
Earth sheet  
Accessory6  
Accessory7  
|
English 19  
KDC-U7056DAB only  
Installing the Digital radio antenna  
When installing the antenna on the  
<
left side  
• Take the following precautions when  
Accessory7  
passing the antenna cable inside the front  
pillar where the air bag is installed.  
- Install the amplifier part of the antenna  
cable in front or above the air bag so  
that the antenna and the air bag do not  
interfere.  
Accessory6  
Earth sheet  
Accessory7  
Match the protrusion with 5  
8 Remove the film covering the earth  
sheet and paste the earth sheet on the  
metal part of the vehicle.  
Provide sufficient leeway for the earth  
sheet so that it does not interfere with  
the interior parts (front pillar cover).  
Also take care that the interior parts do  
not interfere with the amplifier.  
Air bag  
Front pillar  
- The front pillar cover is secured with  
a special clip which may need to be  
replaced when the front pillar cover is  
removed.  
Front glass  
Accessory7  
Front pillar  
Contact your vehicle dealer for details  
on replacing the front pillar cover and  
availability of replacement parts.  
Interior part  
Earth sheet  
Interior part  
Clip  
9 Wire the antenna cables.  
• Use cord clamper (Accessory 8) to  
secure the antenna to the pillar at  
several locations.  
|
20 Quick Start Guide  
Audio section  
Specifications  
Maximum output power : 50 W x 4  
Full Bandwidth Power (at less than 1% THD)  
FM tuner section  
: 22 W x 4  
Frequency range  
200 kHz step : 87.9 MHz – 107.9 MHz  
50 kHz step : 87.5 MHz – 108.0 MHz  
Usable sensitivity (S/N = 26dB)  
: 7.2dBf (0.63 μV/75 Ω)  
Quieting Sensitivity (S/N = 46dB)  
: 15.2dBf (1.6 μV/75 Ω)  
Frequency response (±3 dB) : 30 Hz – 15 kHz  
Signal to Noise ratio (MONO) : 75 dB  
Stereo separation (1 kHz) : 45 dB  
Preout level/ Load (CD)  
KDC-U7056DAB : 2500 mV/10 kΩ  
KDC-U7056BT/ KDC-U7056BTL : 4000 mV/10 kΩ  
Preout impedance : ≤ 600 Ω  
Speaker Impedance : 4 – 8 Ω  
Tone:  
Band1 : 62.5 Hz ±9 dB, Band2 : 100 Hz ±9 dB  
Band3 : 160 Hz ±9 dB, Band4 : 250 Hz ±9 dB  
Band5 : 400 Hz ±9 dB, Band6 : 630 Hz ±9 dB  
Band7 : 1 kHz ±9 dB,  
Band8 : 1.6 kHz ±9 dB  
Band9 : 2.5 kHz ±9 dB, Band10 : 4 kHz ±9 dB  
Band11 : 6.3 kHz ±9 dB, Band12 : 10 kHz ±9 dB  
Band13 : 16 kHz ±9 dB  
AM tuner section  
Frequency range  
10 kHz step : 530 kHz – 1700 kHz  
9 kHz step : 531 kHz – 1611 kHz  
Usable sensitivity (S/N = 20dB) : 31 dBµ (36 µV)  
Bluetooth section  
Version : Bluetooth Ver. 2.1+EDR Certified  
Frequency range : 2.402 – 2.480 GHz  
Output Power  
DAB tuner section (KDC-U7056DAB)  
: +4dBm (MAX), 0dBm (AVE) Power Class 2  
Frequency range  
L-BAND : 1452.960 MHz – 1490.624 MHz  
BAND III : 174.928 MHz – 239.200 MHz  
Sensitivity : -100 dBm  
Signal to Noise ratio : 80 dB  
Antenna Connector type : SMB  
Antenna Output Voltage (11 – 16V) : 14.4 V  
Antenna Maximun Current : <100 mA  
Maximum Communication range  
: Line of sight approx.10m  
Profiles  
: HFP (Hands Free Profile)  
: SPP (Serial Port Profile)  
: PBAP (Phonebook Access Profile)  
: OPP (Object Push Profile)  
: A2DP (Advanced Audio Distribution Profile)  
: AVRCP (Audio/Video Remote Control Profile)  
CD player section  
Auxiliary input  
Laser diode : GaAlAs  
Digital filter (D/A) : 8 Times Over Sampling  
D/A Converter : 24 Bit  
Spindle speed (Audio files) : 500 – 200 rpm (CLV)  
Wow & Flutter : Below Measurable Limit  
Frequency response (±1 dB) : 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz) : 0.008 %  
Signal to Noise ratio (1 kHz) : 110 dB  
Dynamic range : 93 dB  
Frequency response (±3 dB) : 20 Hz – 20 kHz  
Input Maximum Voltage : 1200 mV  
Input Impedance : 10 kΩ  
General  
Operating voltage : 14.4 V (10.5 – 16V allowable)  
Maximum Current consumption : 10 A  
Installation Size (W x H x D) : 182 x 53 x 159 mm  
Weight : 1.3 kg  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
Specifications subject to change without notice.  
AAC decode : AAC-LC .m4a” files  
USB interface  
USB Standard : USB1.1/ 2.0 (Full speed)  
File System : FAT12/16/ 32  
Maximum Supply current : DC 5 V  
Decode : MP3, WMA, AAC, WAV  
1 A  
|
English 21  
Requirements Pandora:  
Requirements for listening to the Pandora  
are as follows:  
Requirements Aha™:  
Requirements for listening to the Aha™ are  
as follows:  
iPhone or iPod touch  
iPhone or iPod touch  
• Use an Apple iPhone or iPod touch  
running under iOS3 or later.  
• Use an Apple iPhone or iPod touch  
running iOS4 or later.  
• Search for “Pandorain the Apple iTunes  
App Store to find and install the most  
current version of the Pandora application  
on your device.  
• Search for “ahain the Apple iTunes App  
Store to find and install the most current  
version of the Aha™ application on your  
device.  
• iPhone/ iPod touch connected to this unit • iPhone/ iPod touch connected to this unit  
with a KCA-iP102.  
with a KCA-iP102.  
Android™ or BlackBerry®  
Android™  
• Download the Pandora application to  
your smartphone from Pandora site using  
it’s standard browser.  
• Bluetooth must be built in and the  
following profiles must be supported.  
- SPP (Serial Port Profile)  
- A2DP (Advanced Audio Distribution  
Profile)  
NOTE  
• Use Android OS 2.2 or later.  
• Download the Aha™ application to your  
smartphone from the Google Play.  
• Bluetooth must be built in and the  
following profiles must be supported.  
- SPP (Serial Port Profile)  
- A2DP (Advanced Audio Distribution  
Profile)  
NOTE  
• In the application on your device, log in  
and create an account with Pandora.  
(If you are not already a registered user,  
an account can also be created at www.  
pandora.com.)  
• In the application on your device, log in  
and create a free account with Aha.  
• Internet connection by LTE, LTE, 3G, EDGE,  
or WiFi.  
• Because Aha™ is a third-party service,  
the specifications are subject to change  
without prior notice. Accordingly,  
compatibility may be impaired or some  
or all of the services may become  
unavailable.  
• Some Aha™ functionality cannot be  
operated from this unit.  
• aha, the Aha logo, and the Aha trade dress  
are trademarks or registered trademarks  
of HARMAN International Industries, used  
with permission.  
• Internet connection by LTE, LTE, 3G, EDGE,  
or WiFi.  
• Pandora is available only in the U.S,  
Canada, Australia and New Zealand.  
• Because Pandora is a third-party service,  
the specifications are subject to change  
without prior notice. Accordingly,  
compatibility may be impaired or some  
or all of the services may become  
unavailable.  
• Some functions of Pandora cannot be  
operated from this unit.  
• For issues using the application, please  
contact Pandora at pandora-support@  
pandora.com  
PANDORA, the PANDORA logo, and the  
Pandora trade dress are trademarks or  
registered trademarks of Pandora Media,  
Inc., used with permission.  
The marking of products using  
lasers (Except for some areas)  
CLASS 1  
The Bluetooth word mark and logos are  
owned by the Bluetooth SIG, Inc. and any use  
of such marks by JVC KENWOOD Corporation  
is under license. Other trademarks and trade  
names are those of their respective owners.  
The “AAClogo is a trademark of Dolby  
Laboratories.  
“Made for iPodand “Made for iPhone”  
mean that an electronic accessory has been  
designed to connect specifically to iPod or  
iPhone, respectively, and has been certified  
by the developer to meet Apple performance  
standards. Apple is not responsible for the  
operation of this device or its compliance with  
safety and regulatory standards. Please note  
that the use of this accessory with iPod or  
iPhone may affect wireless performance.  
iPhone, iPod, iPod classic, iPod nano, and iPod  
touch are trademarks of Apple Inc., registered  
in the U.S. and other countries.  
LASER PRODUCT  
The label is attached to the chassis/case and  
says that the component uses laser beams  
that have been classified as Class 1. It means  
that the unit is utilizing laser beams that  
are of a weaker class. There is no danger of  
hazardous radiation outside the unit.  
TRA  
REGISTERED No. : ER0106384/13  
DEALER No. : 0016026/08  
iTunes and Safari are trademark of Apple Inc.  
IOS is a trademark or registered trademark of  
Cisco in the U.S. and other countries and is  
used under license.  
Adobe, Acrobat and Reader are either  
registered trademarks or trademarks of Adobe  
Systems Incorporated in the United States  
and/or other countries.  
Android and Chrome are trademark of  
Google Inc.  
BlackBerry®, RIM®, Research In Motion® and  
related trademarks, names and logos are the  
property of Research In Motion Limited and  
are registered and/or used in the U.S. and  
countries around the world. Used under  
license from Research In Motion Limited.  
Internet Explorer and Windows Media are  
registered trademark of Microsoft Corporation  
in the United States and other countries.  
Firefox is a registered trademark of Mozilla  
Foundation in the United States and other  
countries.  
PANDORA, the PANDORA logo, and the  
Pandora trade dress are trademarks or  
registered trademarks of Pandora Media, Inc.,  
used with permission.  
aha, the Aha logo, and the Aha trade dress  
are trademarks or registered trademarks of  
HARMAN International Industries, used with  
permission.  

Polk Audio db521 User Manual
Polk Audio Car Speaker MM455 User Manual
Pioneer GM D7400M User Manual
Pioneer DVD RDS AV Receiver AVH P8400BH User Manual
Panasonic NV S5A User Manual
Panasonic Lumix Mirrorless Camera DMCGF3XK User Manual
Panasonic CQ C5405U User Manual
Omega B2100 User Manual
Lanzar Car Audio Lanzar Street Vision SVDVD28 User Manual
Kenwood KRC 365L User Manual