KDC-U546BT
CD-RECEIVER
INSTRUCTION MANUAL
CD 收放机
使用说明书
© B64-4540-00/00 (MW/M0)
Before Use
Notes
2WARNING
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
To prevent injury or fire, take the following
precautions:
To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
• The characters which can be displayed by this unit
are A-Z 0-9 @ “ ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |
~ .
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
When using this unit for the first time, cancel
the Demonstration mode. Refer to <Exit of the
Demonstration Mode> (page 5).
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
¤
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
About the Terminals of the Unit and
Faceplate
•
To prevent deterioration, do not touch the terminals of the
unit and faceplate with your fingers.
CDs that cannot be used
•
If the terminals on the unit or faceplate get dirty, wipe them
with a clean soft dry cloth.
• CDs that are not round cannot be used.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not
been finalized. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-R/
CD-RW recorder instruction manual.)
• 3 inch CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
English
|
3
Component names and functions
1
2
3
4
5
15 14 13 12 11
10
9
8
7
6
1 Release button
p [4] / [¢] button
The faceplate of the unit can be detached and
taken with you, helping to deter theft. Refer to
<Removing the Faceplate> (page 19).
To select a station, song and setting items.
q Microphone
The microphone for the hands free phone is built
in. When your voice cannot be recognized due
to the low microphone volume, noises or echo
in the vehicle. Adjust the microphone settings
by “MIC GAIN”, “NR LEVEL” and “EC LEVEL” of
<Bluetooth Setup> (page 20).
2 [SRC] button
To turn on this unit and select the Source.
To turn off this unit (press the button at least 1
second).
3 Disc slot
When inserted a disc (label side up), the source is
switched automatically and a song starts playing.
w [VOL] knob
To adjust volume.
Enters function setting mode and setting item
(turn and press the knob). Refer to <Function
Setting Operation> (page 5) for details.
4 Display window
5 [0] button
To eject the disc.
e [BAND] button
To select the remove mode, and remove the USB
device or an iPod (press the button at least 2
seconds or more).
To select the receiving band, the folder for audio
file.
r [
] button
6 USB Terminal
To return to previous item.
When connecting, open up the USB terminal lid. A
USB device or an iPod can be connected.
t [ ] button
To enter the music search mode.
To enter the dialing mode.
7 Auxiliary Input Terminal
Portable audio device can be connected with the
mini-plug (3.5 mm ø).
•
Use the mini-plug cable which is stereo type and does
not have any resistance.
8 [1] – [6] button
To recall the memorized station.
Switches the play mode between music discs,
audio files, and iPod.
9 [VOICE] button
To make a voice dialing call.
To change text scroll. (press the button at least 1
second)
|
4
KDC-U546BT
General operation
Before Using
Function Setting Operation
The basic operating procedure for using this
function is described below. The individual function
items are covered in the operating procedures.
Exit of the Demonstration Mode
Turn off the demonstration mode when you use it
for the first time after installation.
1 Select the source
1 Press the [VOL] knob to quit the demonstration
mode when the messages “CANCEL DEMO” and
“PRESS”, “VOLUME KNOB” are displayed (approx.
15 seconds).
Press the [SRC] button.
Function items vary from source to source. For a list
of the function items. Refer to <Function Item List>
(Page 30).
2 Turn the [VOL] knob to select “YES” and press the
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
”FUNCTION” is displayed.
[VOL] knob.
⁄
•
The demonstration can be set or cancel using
<Demonstration Mode Setting> (page 18).
3 Select your desired function item
Turn the [VOL] knob and press it when the
desired item is displayed.
Repeat the operation until your desired function
item is selected.
Common Operation
Power and source select
Turns the power ON by pressing the [SRC]
button.
⁄
Press the [ ] button to return to the previous
item.
Pressing [SRC] button each time switches
between sources.
Tuner (“TUNER”) ➜ USB or iPod (“USB” or “iPod”)
➜ CD (“CD”) ➜ Auxiliary input (“AUX”) ➜ Standby
(“STANDBY”)
Example:
ꢂ
ꢁ
ꢀ
ꢂ
ꢁ
AUDIO CONTROL
BASS BOOST
ꢀ
ꢀ
ꢂ
[VOL]
[VOL]
ꢁ
DETAILED SET
SUPREME SET
Keeping pressing the [SRC] button at least 1
second turns the power OFF.
DISP SELECT
SETTINGS
⁄
•
When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
In this manual, the above selection is indicated as
Select “AUDIO CONTROL” > “DETAILED SET” >
“SUPREME SET”.
•
The source “CD” and “iPod” can be selected when each
source is ready to play.
Volume
Turning the [VOL] knob adjusts the sound
volume.
4 Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
English
|
5
Music Disc/Audio File/iPod Operation
[SRC] [VOL]
Disc slot
[ꢀ]
CA-U1EX
•
•
CA-U1EX (optional accessory) is
required to connect a USB device.
KCA-iP101 (optional accessory) is
required to connect an iPod.
ꢁ E
[ ] / [ ]
[
] [
]
[BAND]
[1] [6]
USB Terminal
—
Basic Operation
Play function
Playing Disc
Scan play
Insert a disc into the disc slot (label side up).
When inserted, the source is switched
automatically and a song starts playing.
When a disc is inserted, the “IN” indicator is lights
up.
Press the [2] button.
Successively plays the intro of the music in the disc
or folder.
When Scan Play is turned on, “TRACK SCAN”/ “FILE
SCAN” is displayed.
Pressing this button again plays songs in the
normal mode starting with the song being played
now.
Playing USB device or iPod
Connect a USB device or iPod to the USB terminal.
When connected, the source is switched
automatically and a song starts playing.
⁄
•
The Scan play operation cannot be performed while
iPod is playing.
Pause and play
Press the [6] button to pause or resume
playback (track or file).
Random play
Press the [3] button.
Randomly plays the music in the disc or folder.
When Random Play is turned on, “DISC RANDOM”/
“FOLDER RANDOM” is displayed.
Folder select
Press the [BAND] button switches a folder.
The iPod can be operated only when a category
has been selected in the search mode.
Press this button again cancels the Random play.
Song select
Press the [4] or [¢] button selects a song
(track or file).
Fast reverses or forwards the music while
pressing the [4] or [¢] button.
(No sound is output while playing audio file.)
Repeat play
Press the [4] button.
Switches between Track Repeat (“TRACK REPEAT”)
and OFF (“REPEAT OFF”) when pressed while
playing a CD.
Switches between File Repeat (“FILE REPEAT”),
Folder Repeat (“FOLDER REPEAT”), and OFF
(“REPEAT OFF”) when pressed while playing an
audio file.
Ejecting Disc
Press the [0] button ejects a disc.
You can eject the disc for 10 minutes after
switching off the engine.
Removing USB device or iPod
Press the [0] button for at least 2 seconds can
be entered to the USB Remove mode (“USB
REMOVE” is displayed) and the USB device, iPod
can be removed safely.
Selecting CD, USB or iPod source
Press the [SRC] button.
Select the “CD”/“USB” or “iPod” display.
|
6
KDC-U546BT
Function of iPod
Cancelling the Music Search mode
Press the [
] button for at least 1 second.
All Random
⁄
All songs in iPod are played at random.
•
Skip Search: The number of songs to be skipped is
determined by the ratio of the total number of songs in
the list which is selected. Set the ratio with “SKIP SEARCH”
of <Audio File/ iPod Setting> (page 9). Keep pushing the
Press the [3] button for at least 1 second.
Pressing the button toggles the setting between
All random play on (“ALL RANDOM”) and off
(“RANDOM OFF”). Press this button again cancels
the Random play.
[
4] or [¢] button for 3 seconds or longer skips songs
at 10% regardless of the setting.
•
* This operation is effective only for the files registered in
the database created with KENWOOD Music Editor.
⁄
•
•
•
The time required to turn on the all random function
may become longer depending on the number of songs
in iPod.
Function of iPod
Turning on the all random function changes the iPod
browse item to “SONGS”. This browse item will not be
changed even if the all random function is turned off.
If the browse item is changed to search for music while
the all random function is on, the all random function is
turned off and the songs in the browse item are played
at random.
Music Search for iPod
Searching for the song (in iPod) you want to play.
1 Enter Music Search mode
Press the [ ] button.
“SEARCH” is displayed.
2 Search for music
Operation type
Move between items
Skip Search
Select an item
Return to previous item Press the [ ] button.
Function of Audio file/ CD source
Operation
Turn the [VOL] knob.
Music Search
Press the [
Press the [VOL] knob.
4] or [¢] button.
Selecting the music you want to listen to from the
device or media being played now.
1 Enter Music Search mode
Press the [ ] button.
“SEARCH” is displayed.
Return to Top menu
Search by Alphabet
Press the [BAND] button.
Press the [ ] button. Refer to <Alphabet
Search> (page 8).
Displays the current Audio file name.
Cancelling the Music Search mode
2 Search for music
Press the [
] button for at least 1 second.
Audio file
⁄
•
Skip Search: The number of songs to be skipped is
determined by the ratio of the total number of songs in
the list which is selected. Set the ratio with “SKIP SEARCH”
of <Audio File/ iPod Setting> (page 9). Keep pushing the
Operation type
Operation
Move between folders/ Turn the [VOL] knob.
files
Skip Search*
Select of folder/file
Press the [
Press the [VOL] knob.
4] or [¢] button.
[4] or [¢] button for 3 seconds or longer skips songs
at 10% regardless of the setting.
If no characters included in a song name can be
displayed, the browse item name and digits are
displayed.
Return to previous folder Press the [ ] button.
Return to root folder Press the [BAND] button.
•
“<” or “>” beside the displayed folder name
indicates that this folder is preceded or followed by
another folder.
Items
Playlists
Artists
Albums
Songs
Display
Items
Podcasts
Genres
Display
“PLIST***”
“ART***”
“ALB***”
“PRGM***”
“PDCT***”
“GEN***”
“COM***”
CD source
Composers
Operation type
Move between track
Select of track
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Return to first track
Press the [BAND] button before selecting
a track.
English
|
7
Music Disc/Audio File/iPod Operation
Function of iPod
You can select the song to play by referring to
<Music Search for iPod> (page 7).
Alphabet Search
2 Register the song
You can select a song by alphabet. This function
searches songs whose name contain the specified
character(s) in the list of the selected browse item
(artist, album, etc.).
Press the [5] button for at least 2 seconds.
“## STORED (Registration number)” is displayed.
You can register up to 10 songs.
⁄
1 Enter Music Search mode
Press the [ ] button.
“SEARCH” is displayed.
•
Make a Playlist from the songs stored in one iPod. If you
attempt to register a song stored in a different iPod, ”NO
INFO” appears and then ”MPLIST DELETE” appears. To
delete the Playlist, turn the [VOL] knob to select “YES”
and then press the [VOL] knob.
2 Enter Alphabet Search mode
Press the [ ] button.
“SEARCH <_ _ _>” is displayed.
•
The song displayed in the Music Search mode can be
registered in the same manner. For how to use the music
search function, refer to <Music Search for iPod> (page
7).
3 Select the character to be searched for
Operation type
Operation
•
•
If you attempt to register the eleventh song, ”MEMORY
FULL” appears and you cannot register it accordingly. To
register the song, delete an unnecessary song.
Do not register Podcasts. Songs you do not want to
register may be registered, or playback may not be
carried out correctly.
Select the characters
Turn the [VOL] knob.
Move the cursor to the Press the [
enter character position
4] or [¢] button.
You can enter up to 3 characters.
4 Determine the selected character
Playing the Song in the Playlist
Press the [VOL] knob.
Start search. When the search is completed,
the music search mode is selected again at the
selected character position.
1 Display the Playlist
Press the [5] button.
“MY PLAYLIST” is displayed.
Cancelling the Alphabet Search mode
2 Play the song in the Playlist
Press the [
] button for at least 1 second.
Turn the [VOL] knob to select the song you
want to play, and then press the [VOL] knob.
⁄
•
The time of Alphabet search may become long
⁄
depending on the number of songs or number of
playlists in iPod.
•
Turning the power OFF stops playing the song in the
Playlist.
•
To search for a character other than A to Z and 0 to 9, enter
“*” at the first character position. In this case, you cannot
enter any character at the second and third character
positions.
•
If a song does not end with at least 1 second of silence,
the ending part of the song may not play out.
Deleting a Song from the Playlist
•
If the first character string begins with an article “a”, “an”,
or “the” in the alphabet search mode, it is searched for in
defiance of the article.
1 Turn the [VOL] knob to display the song you
want to delete, and then press the [VOL] knob
for at least 2 seconds.
2 Turn the [VOL] knob to select ”ONE” or “ALL”,
and then press the [VOL] knob.
Function of iPod
Selecting “DELETE ALL” deletes all songs.
My Playlist for iPod
3 Turn the [VOL] knob to select ”YES”, and then
press the [VOL] knob.
“COMPLETE” is displayed.
Allows you to register your favorite songs in the
Playlist of this unit. You can register up to 10 songs
in the Playlist.
⁄
Registering Songs in the Playlist
•
You can also delete all songs from the Playlist by
selecting “MPLIST DELETE” described in <Audio File/iPod
Setting> (page 9).
1 Play the song you want to register
Press the [BAND], [4], and [¢] button.
|
8
KDC-U546BT
Function of remote control
Audio File/ iPod Setting
Direct Music Search
You can select following setting items.
Searching the music by entering the track number.
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
1 Enter Direct Music Search mode
Press the [DIRECT] button.
2 Select the function item
2 Enter the music number
Turn the [VOL] knob and press it when the
desired item is displayed.
Press the number buttons.
3 Search the music
Select “SETTINGS” > Function item.
Press the [4] or [¢] button.
Function item
Selectable setting/item
Cancelling Direct Music Search
“SKIP SEARCH”
The number of songs to be skipped is
determined by the ratio of the total number of
songs in the list which is selected. (iPod and
KENWOOD Music Editor File only)
0.5%/1%/5%/10%
Press the [
] button.
⁄
•
Direct Music Search cannot be performed during playing
of iPod, “Music Editor” media, Random play, or scan play.
“MPLIST DELETE”
Deletes the saved My Playlist. <My Playlist for
iPod>(page 8) (iPod only)
NO/YES
(Factory setting: Underlined)
3 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
When select “MPLIST DELETE”:
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
Deletes the saved My Playlist.
4 Exit Function Setting mode
Press the [
] button for at least 1 second.
Function of iPod
iPod Control by Hand Mode
Allowing you to operate iPod with the control on
the iPod.
Press the [1] button.
Pressing the button toggles the setting between
iPod control by hand mode on (“HANDS ON”) and
off (“HANDS OFF”).
⁄
•
•
•
In the iPod Control by hand mode, iPod cannot be
operated using this unit.
This mode is not compatible with music information
display. The display will show “iPod MODE”.
iPod can be operated when it conforms to the iPod
control function.
English
|
9
Tuner Operation
Tuner Setting
[SRC] [VOL]
You can select following Tuner Setting items.
1 Select the TUNER source
Press the [SRC] button.
Select the “TUNER” display.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
ꢁ
E
]
[
]
[BAND]
[
] / [
—
[1] [6]
3 Select the function item
Basic Operation
Turn the [VOL] knob and press it when the
desired item is displayed.
Selecting Tuner source
Press the [SRC] button.
Select “SETTINGS” > Function item.
Select the “TUNER” display.
Function item Selectable setting/item
“LOCAL SEEK”
Only stations whose reception is good are searched
in auto seek tuning. (AM band only)
OFF/ON
Selects the tuning mode of the radio.
AUTO1: Automatic search for a station.
AUTO2: Search in order of the stations in the Preset
memory.
Selecting the Receiving Band
Press the [BAND] button.
Each time you press the button, the receiving band
alternates between the FM1, FM2, FM3, MW, SW1,
and SW2
“SEEK MODE”
Selecting the Receiving station
Press the [4] or [¢] button.
During reception of stereo stations the “ST”
indicator lights up.
MANUAL: Normal manual tuning control.
“AUTO MEMORY”* Putting stations with good reception in the memory
automatically.
NO/YES
“MONO SET”
You can reduce the noise when stereo broadcasts
are received as monaural. (FM band only)
OFF/ON
Selecting the preset channel
Press the [1] – [6] button.
(Factory setting: Underlined)
4 Make a setting
Station Preset Memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Putting a station in the memory.
When select “AUTO MEMORY”:
Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
When 6 stations that can be received are put in the
memory, auto memory entry closes.
1 Select the frequency to put in the memory
Press the [4] or [¢] button.
2 Select the number to put in the memory
Press the [1] – [6] button for at least 2 seconds.
⁄
5 Exit Function Setting mode
•
Up to 6 stations with a different band (FM/MW/SW) can
be memorized to the [1] – [6] button according to the
setting of “PRESET TYPE” of <Initial Setting> (page 18).
Press the [
] button for at least 1 second.
⁄
•
* This setting can be made when “TYPE NORMAL” is
selected for the “PRESET TYPE” of <Initial Setting> (page
18).
|
10 KDC-U546BT
Function of remote control
Direct Access Tuning
Tuning in a desired radio station by entering the
frequency.
1 Enter Direct Access Tuning mode
Press the [DIRECT] button.
“– – – –” is displayed.
2 Enter the frequency
Press the number buttons.
Example:
Desired frequency
92.1 MHz (FM)
810 kHz (AM)
Press button
[9], [2], [1]
[8], [1], [0]
3 Tune in to entered the frequency
Press the [4] or [¢] button.
Cancelling Direct Access Tuning
Press the [
] button.
⁄
•
You can enter the FM band frequency in steps of a
minimum of 0.1 MHz.
Frequency Step Setting
Changing the tuning frequency step.
The original setting is FM band 50 kHz and MW
band 9 kHz.
1 Turn the power OFF
Press the [SRC] button for at least 1 second.
2 Switch the frequency step
While pressing the [1] and [5] buttons, press the
[SRC] button.
Release your fingers from the button after the
display appears.
The frequency step changes to FM band 200 kHz,
and MW band 10 kHz.
⁄
•
When the same operation is repeated, the frequency
step returns to the original setting.
•
When the frequency step is changed, the frequencies in
the memory are deleted.
English
|
11
Operation of Hands-Free Phoning
⁄
[SRC] [VOL]
•
When registering from this unit. Refer to <Registering
Bluetooth Device> (page 21).
•
For details on the Bluetooth cell-phone with the hands-
free function, see <About the Cell-Phone> (page 29).
Making a Call
ꢁ
E
]
—
[
][ ][BAND]
[
] / [
[VOICE] [1] [6]
You can select following dialing method.
Connecting a Bluetooth Device
1 Enter Bluetooth mode
Press the [VOL] knob.
“BT MODE” is displayed.
Before use the Bluetooth device, you need to
connect Bluetooth device to this unit. The following
3 steps procedure is necessary.
2 Enter dialing method mode
Press the [ ] button.
“PHONE BOOK is displayed.
Step 1. Pairing (Registering from Bluetooth
devices)
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing).
3 Select a dialing method
Turn the [VOL] knob and press it when the
desired item is displayed.
1 Turn on this unit.
Display
Overview
Press the [SRC] button.
“PHONE BOOK” Selecting the initial to be searched or name for the
phone book.
2 Start registering this unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD BT
CD/R-3P1” from the list of connected units.
“OUT-CALL”
“IN-CALL”
Calling a number in the outgoing call list.
Calling a number in the incoming call list.
“MISSED CALLS” Calling a number in the missed calls list.
“NUMBER DIAL” Making a call by entering phone number.
Operation method of each mode is described
below.
3 Enter a PIN code
Input the PIN code (“0000”) in the Bluetooth
device.
4 Exit the dialing method mode
Check that registration is complete on the
Bluetooth device. PIN code is set to “0000” as
the default. You can change this code. Refer to
<Registering PIN Code> (page 22).
Press the [
] button for at least 1 second.
Disconnecting a Call
Press the [SRC] button.
4 By operating the Bluetooth device, start hands-
free connection.
Calling a Number in the Phone Book
Step 2. Connection
If you have registered 2 or more cell-phones, you
need to select one of them. For more details, see
<Selecting the Bluetooth Device You Wish to
Connect> (page 23).
When a cell-phone is connected, the “BT” indicator
is lights up.
1 Select the Phone Book mode
For how to select dialing method, refer to <Making
a Call> (page 12).
Select the “PHONE BOOK” display.
2 Select the initial to be searched for
Operation type
Move to the next character. Turn the [VOL] knob.
Move to the next row. Press the [BAND] button.
Determine the selected initial. Press the [VOL] knob.
Operation
Step 3. Hands-free phoning
You can do hand-free phoning when the
connection is made.
|
12 KDC-U546BT
3 Select the name
Operation type
Move to the next phone
number.
3 Make a call
• Press the [VOL] knob.
• Press the [OK] button on the remote
controller.
Operation
Turn the [VOL] knob.
Move to the next name.
Press the [4] or [¢] button.
⁄
•
You can input max 25 digits.
4 Make a call
Press the [VOL] knob.
⁄
Make a Voice Dialing Call
•
To use the Phone Book, it must be downloaded to this
unit in advance. Refer to <Downloading the Phone
Book> (page 22).
1 Enter voice recognition mode
Press the [VOICE] button.
“V-RECG READY” is displayed.
•
During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.
2 Press the [VOL] knob.
“PB NAME” is displayed.
When a beep is heard, say the name within 2
seconds.
Calling a Number in the Call Log
3 “PN TYPE” is displayed.
1 Select the call log mode
When a beep is heard, say the category name
within 2 seconds.
For how to select dialing method, refer to <Making
a Call> (page 12).
Select the “OUT-CALL” (outgoing call), “IN-CALL”
(incoming call), or “MISSED CALLS” (missed call)
display.
4 Make a call
Press the [VOL] knob.
Move to the next phone number
Turn the [VOL] knob.
2 Select a name or phone number
Turn the [VOL] knob.
⁄
3 Make a call
•
If your voice cannot be recognized, a message is
displayed. Pressing the [VOL] knob allows you to retry
voice input. (page 35)
Press the [VOL] knob.
⁄
•
•
Both the name and category require registration of a
voice tag. (page 24)
Audio sound is not output during voice recognition.
•
The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
Registering to the Preset Dial Number
(Preset Memory)
Dial a Number
1 Enter the phone number you wish to register
Enter the phone number with reference to the
following:
Dial a number/ Calling a number in the call log/
Calling a number in the Phone Book
1 Select the number dial mode
For how to select dialing method, refer to <Making
a Call> (page 12).
Select the “NUMBER DIAL” display.
2 Enter a phone number
2 Select the number to put in the memory
Operation type
Operation
Press the [1] – [6] button for at least 2 seconds.
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Press the [
Press the [
¢
4
] button.
] button.
• Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
English
|
13
Operation of Hands-Free Phoning
Speed Dialing (Preset Dial)
Call Waiting
1 Select the number you want to recall from the
memory
Answering Another Incoming Call with the
Current Call Suspended
Press the [1] – [6] button.
1 Press the [VOL] knob.
2 Make a call
2 Turn the [VOL] knob and press it when the
Press the [VOL] knob.
desired item is displayed.
Select “ANSWER”.
⁄
•
You need to register the preset dial number.
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button.
Receiving a Call
Continuing the Current Call
1 Press the [VOL] knob.
Answering a Phone Call
Press the [VOL] knob.
2 Turn the [VOL] knob and press it when the
desired item is displayed.
⁄
Select “REJECT”.
•
The following operations disconnect the line:
- Insert a CD.
Answering the Waiting Call after Terminating
the Current Call
Press the [SRC] button.
- Connect a USB device.
•
The name of the calling party is displayed if it has already
been registered in the Phone Book.
Switching between the Current Call and Waiting
Call
Press the [VOL] knob.
Rejecting an Incoming Call
Press the [SRC] button.
Each pressing of this knob switches the calling
party.
During a Call
Disconnecting a Call
Press the [SRC] button.
Other Functions
Clearing the Disconnection Message
Press the [VOL] knob.
“HF DISCONCT” disappears.
Switching to the Private Mode
Press the [6] button.
Switches between Private talk (“PRIVATE TALK”) and
Hands-free talk each time this button is pressed.
Switching between Display Modes
Press the [ ] button.
Pressing this button each time switches between
⁄
•
Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection.
If this happens, the source cannot be switched back to
the hands-free talk mode by operating this unit. Operate
your cell-phone to return to the hands-free talk mode.
name and telephone number.
Display of Phone Number Type
(Category)
Adjusting the Voice Volume during a Call
Turn the [VOL] knob.
The category items in the Phone Book are displayed
as follows.
Display
“GE”
“HM”
“OF”
Information
General
Home
Office
“MO”
“OT”
Mobile
Other
|
14 KDC-U546BT
Audio Adjustments
“SUB-W LEVEL”
“DETAILED SET”
You can set subwoofer level.
–15 — 0 — +15
Move to detailed item
[SRC] [VOL]
“LPF SUBWOOFER” Selects cut off frequency of subwoofer output.
85/120/160/THROUGH (OFF) Hz
“SUB-W PHASE” Selects the phase of subwoofer output.
REVERSE (180°)/ NORMAL (0°)
“SUPREME SET” Turns on/off the supreme function.
OFF/ON
“VOLUME OFFSET” Sets each source’s volume as a difference from
the basic volume.
[
]
–8 — 0 (AUX: –8 —0 — +8)
(Factory setting: Underlined)
Audio Control
You can adjust following Audio Control items.
4 Make a setting
1 Select the source
Turn the [VOL] knob and press it when the
desired item is displayed.
Press the [SRC] button.
Select the “TUNER”/“USB”/“iPod” or “CD”/“AUX”
display.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
⁄
• SUPREME:
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is
cut off when encoding at low bit rate (less than 128Kbps,
Sampling frequency is 44.1kHz).
3 Select the function item
Turn the [VOL] knob and press it when the
desired item is displayed.
Supplementing is optimized by compression format
(MP3 or WMA) and processed according to bit rate. The
effect is negligible with music that is encoded at high
bit rate, variable bit rate or has minimal high frequency
range.
Select “AUDIO CONTROL” > Function item or
select “AUDIO CONTROL” > “DETAILED SET” >
Function item.
Function item
Selectable setting/item
“SUBWOOFER SET” Turns on/off the subwoofer output.
OFF/ON
“BASS BOOST”
“SYSTEM Q”
Selects bass boost setting mode.
OFF/LV1/LV2 (The indicator turns on according
to the setting.)
Switches between the following preset equalizer
curves. “EQ“ indicator is lights when System Q is
set to an EQ mode other than“NATURAL”.
NATURAL/USER/ROCK/POPS/EASY/TOP40/
JAZZ/GAME
For USER: This appears when Bass level, Middle
level, and Treble level are adjusted.
You can set bass level for each source.
–8 — 0 — +8
You can set middle level for each source.
–8 — 0 — +8
You can set treble level for each source.
–8 — 0 — +8
Adjusts left/right speaker balance.
(Left) L15 — 0 — R15 (Right)
Adjusts front/rear speaker balance.
(Rear) R15 — 0 — F15 (Front)
“BASS LEVEL”
“MID LEVEL”
“TRE LEVEL”
“BALANCE”
“FADER”
English
|
15
Display Settings
4 Exit Function Setting mode
[SRC] [VOL]
Press the [
] button for at least 1 second.
⁄
•
•
•
When you select the clock display, the display setting of
each source will be changed to the clock display.
If the selected display item does not have any
information, alternative information is displayed.
When selecting “FOLDER NAME” while playing with
iPod, names will be displayed depending on currently
selected browsing items.
[
]
[VOICE]
•
•
If the iPod Control by Hand Mode is set to on while
playing the iPod, “iPod MODE” is displayed.
If all characters cannot be displayed while playing with
iPod, the file number in the list is displayed.
Display Selection
Changing displayed information on each source
following.
Information
Music title
Folder name
File name
Display
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
“TITLE***”
“FOLDER***”
“FILE***”
2 Enter Display Select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Text Scroll
Select “DISP SELECT”.
Scrolling the displayed File name, Song title, etc.
3 Select the text
Turn the [VOL] knob and press it when the
desired item is displayed.
Press the [VOICE] button for at least 1 second.
In Tuner source
Information
Frequency
Clock
Display
“FREQUENCY”
“CLOCK”
In Audio file/ iPod source
Information
Display
Music title & Artist name
Album & Artist name
Folder name
File name
Play time & Music number
Clock
“TITLE/ARTIST”
“ALBUM/ARTIST”
“FOLDER NAME”
“FILE NAME”
“P-TIME”
“CLOCK”
In CD source
Information
Disc title
Track title
Play time & Track number
Clock
Display
“DISC TITLE”
“TRACK TITLE”
“P-TIME”
“CLOCK”
In Standby/ Auxiliary input source
Information
Source name
Clock
Display
“SOURCE NAME”
“CLOCK”
|
16 KDC-U546BT
Display Setting
Auxiliary Input Display Setting
You can select following Display Setting items.
Selecting the display when changing to Auxiliary
input source.
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
1 Select the AUX source
Press the [SRC] button.
Select the “AUX” display.
2 Select the function item
Turn the [VOL] knob and press it when the
desired item is displayed.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
Select “SETTINGS” > “DISPLAY” > Function item.
Function item
“DIMMER SET”
Selectable setting/item
Adjusts the brightness of the display according to
the surrounding illumination.
3 Enter Auxiliary input display setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “SETTINGS” > “AUX NAME SET”.
The presently selected Auxiliary input display is
displayed.
OFF/ON
“TEXT SCROLL”
Scrolling the displayed File name, Song title, etc.
Selecting AUTO scrolls them automatically.
AUTO/MANUAL
“BT DVC STATUS”
You can display the connection status, signal
strength, and battery level of cell-phone.
HF-CON: Connection status.
BATT: Battery level of cell-phone.
SIGNAL: Signal strength of cell-phone.
• Data are not displayed if information cannot be
obtained from the cell-phone.
• Since the number of steps of this unit is
different from that of the cell-phone, the
statuses displayed on this unit may discord
from those displayed on the cell-phone.
4 Select the Auxiliary input display
Turn the [VOL] knob and press it when the
desired item is displayed.
“AUX”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
(Factory setting: Underlined)
3 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
4 Exit Function Setting mode
Press the [
] button for at least 1 second.
English
|
17
Other Functions
Release button
3 Set the Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
[SRC] [VOL]
Select “ON” or “OFF”.
4 Exit Function Setting mode
Press the [
] button for at least 1 second.
[
]
Initial Setting
You can select following Initial Setting items.
Clock Adjustment
1 Select the Standby source
Press the [SRC] button.
Select the “STANDBY” display.
1 Select the source
Press the [SRC] button.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
3 Enter Clock adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “SETTINGS” > “CLOCK” > “CLOCK
ADJUST”.
3 Select the function item
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “INITIAL SET” > Function item.
Function item Selectable setting/item
The hour display blinks
“PRESET TYPE” TYPE NORMAL:
1 station can be assigned to 1 preset button in each
of 6 bands (FM1, FM2, FM3, MW, SW1 and SW2),
i.e., a total of 36 stations (6 stations x 6 bands) can
be preset.
4 Adjusting Clock
Turn the [VOL] knob to set the hours and press
it when to finish the hour adjusting.
The minute display blinks.
TYPE MIX:
Turn the [VOL] knob to set the minutes and
press it when to finish the minute adjusting.
A total of 6 stations can be assigned to a total of 6
preset buttons regardless of band (FM1, FM2, FM3
MW, SW1, and SW2). You can recall a preset station
without switching between bands.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
“KEY BEEP”
Setting the operation check sound (beep sound)
on/off.
OFF/ON
Demonstration Mode Setting
“TDF ALARM”
Informs you by alarm sound about 30 seconds
that you forgot to detach the faceplate when ACC
is set to OFF.
Turning the demonstration mode ON/OFF.
OFF/ON
1 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
“BUILT-IN AUX” When this is set to ON, AUX source can be selected.
ON1: Outputs the sound of external unit connected
to the AUX terminal when switched to AUX
source.
2 Select Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
ON2: Activates the attenuator function when
turning on the power with AUX source
selected. Cancel the attenuator function
by turning the volume knob clockwise
when listening to the audio of the external
equipment.
Select “DEMO MODE”.
OFF: Disables the selection of AUX source. Set to
OFF when not using the AUX terminal.
|
18 KDC-U546BT
“CD READ”
Sets the method for reading CD.
Removing the Faceplate
1: Automatically distinguishes between audio file
disc and music CD when playing disc.
2: Forces playing as music CD.
The faceplate of the unit can be detached and taken
with you, helping to deter theft.
“SWITCH PREOUT” Switches the preout between rear output (“REAR”)
and subwoofer output (“SUB-W”)
Detach the faceplate
Press the Release button.
REAR/SUB-W
“SP SELECT”
Fine-tuning so that the System Q value is optimal
when setting the speaker type as follows;
SP OFF: OFF
SP 5/4: For 5 & 4 in. speaker
SP 6*9/6: For 6 & 6x9 in. speaker
SP OEM: For the OEM speaker
Display the firmware version and update the
firmware.
Reattaching the Faceplate
Refer to the following diagram when
reattaching the faceplate.
“F/W UP”
MEDIA USB: Select a USB device.
MEDIA CD: Select CD.
For how to update the firmware, access our web
site.
¤
•
After pressing the Release button, detach the faceplate
immediately. If the faceplate is left attached, it can fall
due to vibration and so on.
The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
Keep the faceplate in its faceplate case while detached.
Do not place the faceplate (and the faceplate case)
in areas exposed to direct sunlight, excessive heat or
humidity. Also avoid places with too much dust or the
possibility of water splashing.
(Factory setting: Underlined)
4 Make a setting
Turn the [VOL] knob and press it when the
desired item is displayed.
•
•
•
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
How to Reset Your Unit
If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when
the Reset button is pressed.
1 Release the faceplate lock so that it can be
removed.
Refer to <Removing the Faceplate> (page 19).
2 Press the Reset button and reattaching the
faceplate.
Reset button
English
|
19
Bluetooth Setup
“AUTO ANSWER” This function automatically answers (responds
to) a call after lapse of the preset time interval
for automatic answer.
[SRC] [VOL]
OFF: Does not answer the phone call
automatically.
0: Automatically answers the phone call at once.
1 – 8 –99: Automatically answers the phone
call after lapse of 1 – 99 seconds.
“BT SP SELECT” You can specify the audio output speakers.
Select the speaker which is further from the
microphone in order to prevent howling or
echoes.
ꢁ
E
]
[
] / [
[
] [
]
Bluetooth Setup
SP FRONT: Outputs audio from the front-left and
front-right speakers.
You can select following Bluetooth Setup items.
SP ALL: Outputs audio from the all speakers.
“CALL BEEP”
You can output a beep from the speaker when a
call comes in.
ON: Beep is heard.
OFF: Beep is canceled
1 Enter Bluetooth mode
Press the [VOL] knob.
“BT MODE” is displayed.
2 Enter Function Setting mode
Press the [VOL] knob for at least 1 second.
“FUNCTION” is displayed.
“BT F/W UPDATE” Display the firmware version and update the
firmware. Refer to <Displaying the Firmware
Version> (page 22).
“MIC GAIN”
Adjust the sensitivity of the built-in microphone
for a telephone call. Adjust the voice of caller.
Setting to“+”increases the voice volume.
–3 – 0 – +3
3 Select the function item
Turn the [VOL] knob and it when the desired
item is displayed.
“NR LEVEL”
Reduce the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to“+”increases the
noise reduction.
Select “SETTINGS” > Function item or select
“SETTINGS” > “DETAILED SET” > Function item.
Function item
Selectable setting/item
“PHONE SELECT”
Selects a cell-phone connection. Refer to
<Selecting the Bluetooth Device You Wish to
Connect> (page 23).
–3 – 0 – +3
“EC LEVEL”
Adjusts the level of echo cancellation. Setting to
“+”increases the echo cancel reduction.
–2 – 0 – +2
“SMS DOWNLOAD” Download a short message. Refer to
<Downloading the SMS> (page 23).
(Factory setting: Underlined)
“SMS INBOX”
Display the received short message. Refer to
<SMS (Short Message Service)> (page 24).
Registers voice for voice recognition and
voice to select the Phone number category in
Phone book. Refer to <Adding a Voice Dialing
Command> (page 24) and <Setting a Voice
Command for Category> (page 25).
4 Make a setting
“VOICE TAG”
Turn the [VOL] knob and press it when the
desired item is displayed.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
“DETAILED SET”
Move to detailed item.
“DEVICE REGIST” Registers a Bluetooth device (pairing).
Refer to <Registering Bluetooth device>
(page 21).
“S-DVC SELECT”
“DEVICE DELETE” Cancel registration of the Bluetooth device. Refer
to <Deleting a Registered Bluetooth Device>
(page 21).
“PIN CODE EDIT” Specify the PIN code required when registering
this unit using the Bluetooth device. Refer to
<Registering PIN Code> (page 22).
|
20 KDC-U546BT
Registering Bluetooth Device (Pairing)
2 Enter Special device registration mode
Press the [VOL] knob.
A list is displayed.
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to 5 Bluetooth devices to this unit.
3 Select a device name
Turn the [VOL] knob and press it when the
desired device name is displayed.
If “COMPLETE” is displayed, registration is
completed.
Registering from this unit
1 Select Bluetooth device registration mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “DETAILED SET” > “DEVICE
REGIST”.
4 Go through the procedure step 3 of <When
registering from this unit> and complete the
registration (pairing).
2 Enter Bluetooth device registration mode
Press the [VOL] knob.
Search for the Bluetooth device.
Cancelling Special device registration mode
Press the [VOL] knob for at least 1 second.
⁄
When search is completed, “FINISHED” is displayed.
•
If the device name is not in the list, select “OTHER
PHONE”.
3 Select the Bluetooth device
Turn the [VOL] knob and press it when the
desired Bluetooth device name is displayed.
Deleting a Registered Bluetooth Device
4 Input the PIN code
You can delete a registered Bluetooth device.
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
1 Select Bluetooth device deletion mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Press the [¢
4
] button.
] button.
Press the [
Select “SETTINGS” > “DETAILED SET” > “DEVICE
DELETE”.
5 Transmit the PIN code
Press the [VOL] knob.
If “PAIRING OK” is displayed, registration is
completed. If the error message appears even
though the PIN code is correct, try Registering
Special Bluetooth device.
2 Enter Bluetooth device deletion mode
Press the [VOL] knob.
“(name)” is displayed.
3 Select the Bluetooth device
6 Return to the device list
Turn the [VOL] knob.
Press the [VOL] knob.
4 Delete the selected Bluetooth device
Press the [VOL] knob.
“DELETE” is displayed.
7 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
5 Exit Function Setting mode
•
This unit allows up to 8 digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be
input from the Bluetooth device.
If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
Press the [
] button for at least 1 second.
⁄
•
When a registered cell-phone is deleted, its Phone Book,
•
log, SMS, and voice tag are also deleted.
Registering Special Bluetooth device
Allow registration of a special device that cannot
be registered normally (pairing).
1 Select Special device registration mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “DETAILED SET” > “S-DVC
SELECT”.
English
|
21
Bluetooth Setup
Registering PIN Code
Downloading the Phone Book
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
1 Select PIN code edit mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “DETAILED SET” > “PIN
CODE EDIT”.
To download automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
2 Enter PIN code edit mode
Press the [VOL] knob.
The current setting of PIN code is displayed.
⁄
•
•
Setting on the cell-phone may be required.
If no phone book data is found in the unit even after
the compete display, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
3 Input the PIN code
Operation type
Operation
Select the numbers.
Turn the [VOL] knob.
Move to the next digit. Press the [
Delete the last digit. Press the [
¢
4
] button.
] button.
To download from the cell-phone manually
1 By operating the cell-phone, end the hands-free
connection.
4 Register a PIN code
Press the [VOL] knob.
2 By operating the cell-phone, send the phone
book data to this unit
By operating the cell-phone, download the phone
If “COMPLETE” is displayed, registration is
completed.
book data to this unit.
• During downloading:
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
“DOWNLOADING” is displayed.
• After completion of downloading:
“COMPLETE” is displayed.
⁄
•
By default, “0000” is specified.
A PIN code can be specified with up to 8 digits.
•
3 By operating the cell-phone, start the hands-
free connection.
⁄
Displaying the Firmware Version
•
Up to 1000 person phone numbers can be registered for
each registered cell-phone.
Display the version of the firmware of this unit.
•
Up to 25 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type
of characters.)
1 Enter Bluetooth Firmware update mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “DETAILED SET” > “BT F/W
UPDATE”.
•
To cancel downloading of the phone book data, operate
the cell-phone.
2 Enter Bluetooth Firmware update mode
Press the [VOL] knob.
The firmware version appears.
3 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
•
For how to update the firmware, access our web site.
|
22 KDC-U546BT
Selecting the Bluetooth Device You
Wish to Connect
Downloading the SMS
Download the short message (SMS) arrived at the
cell-phone so that it can be read on this unit.
When 2 or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
1 Select SMS download mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
1 Select Bluetooth device selection mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “SMS DOWNLOAD”.
2 Enter SMS download mode
Press the [VOL] knob.
Select “SETTINGS” > “PHONE SELECT”.
“DOWNLOADING” is displayed.
When the downloading finishes, “COMPLETE” is
displayed.
2 Enter Bluetooth device selection mode
Press the [VOL] knob.
“(name)” is displayed.
3 Exit Function Setting mode
3 Select the Bluetooth device
Press the [
] button for at least 1 second.
Turn the [VOL] knob.
4 Set up the Bluetooth device
⁄
•
The cell-phone must be able to transmit the SMS using
Press the [VOL] knob.
Bluetooth. Setting on the cell-phone may be required.
If the cell-phone does not support SMS function, the
SMS download item in Function Control mode is not
displayed.
When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
‘✱(name)’ or ‘-(name)’ is displayed.
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
•
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
•
If a cell-phone is already selected, deselect it, and then
select a different one.
English
|
23
Bluetooth Setup
SMS (Short Message Service)
Adding a Voice Dialing Command
The SMS arrived at the cell-phone is displayed on
the receiver.
Add a voice tag to the phone book for voice dialing.
You can register up to 35 voice tags.
A newly arrived message is displayed.
1 Select Phone book name edit mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
¤
•
To prevent car accidents, the driver should not read the
SMS while driving.
Select “SETTINGS” > “VOICE TAG”.
2 Enter Voice Tag edit mode
When a new message arrives
“SMS RECEIVED” is displayed.
Press the [VOL] knob.
The display disappears with any operations.
3 Enter Phone book name edit mode
Turn the [VOL] knob to select “PB NAME EDIT”,
and then press the [VOL] knob.
Displaying the SMS
1 Select SMS Inbox mode
4 Search for the name to register
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select the name to register with reference to 3 in
<Calling a Number in the Phone Book> (page 12).
If a voice tag has already been registered for a
name, “*” is displayed before the name.
Select > “SETTINGS” > “SMS INBOX”.
2 Enter SMS Inbox mode
Press the [VOL] knob.
A message list appears.
5 Select a mode
Turn the [VOL] knob.
3 Select a message
Display
Operation
Turn the [VOL] knob.
“PB NAME REG”
“PB NAME CHK”*
“PB NAME DEL”*
“RETURN”
Register a voice tag.
Play a voice tag.
Delete a voice tag.
Return to step 3.
Each pushing of the [ ] button switches
between telephone number or name and message
reception date.
4 Display the text
* Displayed only when a name for which a voice tag has
been registered is selected.
Press the [VOL] knob.
Turning the [VOL] knob scrolls the message.
Pressing the [VOL] knob again returns to the
message list screen.
Select “PB NAME REG” (Register)
6 Register a voice tag (first)
Press the [VOL] knob.
“ENTER1” is displayed.
When a beep is heard, say a voice tag within 2
seconds.
5 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
•
The unopened message is displayed at the beginning
7 Confirm the voice tag (second)
Press the [VOL] knob.
“ENTER 2” is displayed.
When a beep is heard, say the same voice tag as
that you said in step 5 within 2 seconds.
“COMPLETE” is displayed.
of the list. Other messages are displayed in the order of
reception.
•
The SMS that has arrived when the cell-phone is not
linked with Bluetooth cannot be displayed. Download
the SMS.
•
•
The short message cannot be displayed during
downloading the SMS.
Unread messages are prefixed with an asterisk (*).
8 End registration
Press the [VOL] knob.
Return to step 3. You can register another voice tag
continuously.
⁄
•
If your voice cannot be recognized, a message is
displayed. Pressing the [VOL] knob allows you to retry
voice input. (page 35)
|
24 KDC-U546BT
Select “PB NAME CHK” (Play)
6 Press the [VOL] knob.
Play the registered voice and return to step 3.
Select “PB NAME DEL” (Delete)
6 Delete a voice tag
Press the [VOL] knob.
7 Turn the [VOL] knob to select “YES”, and then
press the [VOL] knob.
Exit Phone book name edit mode
Press the [
] button for at least 1 second.
⁄
•
Audio sound is not output during voice tag registration.
Setting a Voice Command for
Category
Add a voice tag to the phone number category
(type) for voice calling.
1 Select Phone Number type edit mode
For how to select setup item, refer to <Bluetooth
Setup> (page 20).
Select “SETTINGS” > “VOICE TAG”.
2 Enter Voice Tag edit mode
Press the [VOL] knob.
3 Enter Phone Number type edit mode
Turn the [VOL] knob to select “PN TYPE EDIT”,
and then press the [VOL] knob.
4 Select the category (type) you wish to set
Turn the [VOL] knob and press it when the
desired category name is displayed.
“GENERAL”/ “HOME”/ “OFFICE”/ “MOBILE”/ “OTHER”
5 Select a mode
Turn the [VOL] knob.
Display
Operation
“PB TYPE REG”
“RETURN”
Register a voice tag.
Return to step 3.
6 Register the category (type) by performing
steps 6 to 8 of select “PB NAME REG” (Register)
in <Adding aVoice Dialing Command> (page 24).
7 Exit Function Setting mode
Press the [
] button for at least 1 second.
⁄
•
Set the voice tag for all the 5 categories. If the voice tag
is not registered for all the categories, the Phone book
may not be recalled by voice command.
English
|
25
Basic Operations of Remote Control
In iPod/CD/Audio file Source
Music select [4]/[¢] button
Folder/Disc select [FM+]/[AM–] button
Pause/Play [38] button
Enter Music search mode [5]/[∞] button
Movement between folders/files in Music search
VOL
SRC
ATT
ENT
ꢂ/P
mode [5]/[∞] button
Return to previous folder
[
] button
AUD
FM
EXIT
AM
Hands-Free Phone Control
0 — 9
Making a call
Enter Bluetooth mode
[
] button
Enter the dialing method selection mode
[5]/[∞] button
DIRECT/OK
(page 9, 11, 13)
Select a dialing method [ENT] button
Number dial input
Operation type
Input a digit.
Input“+”.
Input“#”.
Input“*”.
Operation
Volume control [VOL] button
Source select [SRC] button
Volume reduce [ATT] button
“ATT“ indicator is blinks when the attenuator function
is on. When the button is pressed again, the volume
returns to the previous level.
[0] – [9] buttons
[¢] button
[FM+] button
[AM–] button
[4] button
Clear the entered phone number.
Make a call [OK] button
Enter Audio Control mode [AUD] button
⁄
Receiving a call
•
Refer to <Audio Control> (page 15) for the operation
method, such as the procedures for Audio control and
others operations.
Answer the call
[
] button
Switch between the private talk mode and the
hands-free talk mode [38] button
Return to previous item
[
] button
Exit from mode [EXIT] button
Selection of item [5]/[∞] button
Determination [ENT] button
Call waiting
Answer Another Incoming Call with the Current
Call Suspended
[
] button
Answer another Incoming Call after Terminating
the Current Call [SRC] button
In Tuner Source
Continue the Current Call [1] button
Band select [FM+]/[AM–] button
Station select [4]/[¢] button
Recall preset stations [1] — [6] button
During a call
End the call [SRC] button
Adjust the voice volume [VOL] button
|
26 KDC-U546BT
Preparing the remote control unit
Pull the battery sheet out from the remote control
unit to the direction of the arrow.
Changing the battery of the remote control
unit
Use a commercially available button battery (CR2025).
1 Insert something narrow like a paperclip into the
hole and pull out the battery tray.
Press
Pull out
2 Insert the battery with the + and – poles aligned
properly, following the illustration inside the case.
CR2025(+side)
¤ CAUTION
• Do not set the remote control in hot places such
as on the dashboard.
• Lithium battery.
Danger of explosion if the battery is incorrectly
replaced.
Replace only with the same or equivalent type.
• The battery pack or batteries shall not be exposed
to excessive heat such sunshine, fire or the like.
• Keep battery out of reach of children and in
original package until ready to use. Dispose of
used batteries promptly. If swallowed contact
physician immediately.
English
|
27
Appendix
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
About Audio file
•
•
•
•
Playable Audio file
MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
iPod/iPhone that can be connected to this
unit
Made for
• iPod nano (1st generation) • iPod nano (2nd generation)
• iPod nano (3rd generation) • iPod nano (4th generation)
• iPod nano (5th generation)
•
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
• iPod with video
• iPod classic
• iPod touch (1st generation) • iPod touch (2nd generation)
Works with
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
• iPhone
• iPhone 3G
• iPhone 3GS
<
v
: Folder
Folder
:
A
CD
(ꢂ)
udiofile
vꢀ
ꢁ
ꢃ
vꢆ
vꢇ
• Update iPod/iPhone software to the latest version.
• Type of control available varies depending on the
type of connected iPod. See www.kenwood.com/
cs/ce/ipod for further details.
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable*. A KCA-iP101 is required (optional
accessory).
* Not supported model KCA-iP500.
Refer to the web site for connectable iPod and iPod
connection cable.
ꢅ
vꢄ
ꢈ
vꢉ
v.
An online manual about audio files is put on the site,
www.kenwood.com/cs/ce/audiofile/. On this online
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
About USB device
• In this manual, the word “USB device” is used for
flash memories and digital audio players which have
USB terminals.
•
If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, “RESUMING” is displayed without displaying a
folder name, etc. Changing the browse item will display a
correct title, etc.
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
•
You cannot operate iPod if “KENWOOD” or “✓” displayed on
iPod.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
|
28 KDC-U546BT
About the Cell-Phone
This unit conforms to the following Bluetooth
specifications:
The marking of products using lasers
CLASS 1
LASER PRODUCT
Version
Profile
Bluetooth Standard Ver. 2.0
HFP (Hands Free Profile)
OPP (Object Push Profile)
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
PBAP (Phone book Access Profile)
SYNC (Synchronization Profile)
For the cell-phones verified for compatibility, access
the following URL:
⁄
This symbol mark indicates that
Kenwood manufactured this product
so as to decrease harmful influence on
the environment.
•
The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
HFP is a profile used to make a hands-free call.
OPP is a profile used to transfer data such as a phone book
between units.
•
•
About “KENWOOD Music Editor”
• This unit supports the PC application “KENWOOD
Music Editor Lite ver1.0” or later.
• When you use the audio file with database
information added by the “KENWOOD Music Editor
Lite ver1.0”, you can search a file by title, album or
artist name using the <Music Search> (page 7).
• In the Instruction manual, the term “Music Editor
media” is used to mean the device that contains
audio files with database information added with
KENWOOD Music Editor.
• “KENWOOD Music Editor Lite ver1.0” is available from
the following web site:
• For further information on “KENWOOD Music Editor
Lite ver1.0”, refer to the site above or the application
help.
•
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
•
•
iTunes is a trademark of Apple Inc.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
•
•
iPhone is a trademark of Apple Inc.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple
performance standards.
•
•
“Works with iPhone” means that an electronic
accessory has been designed to connect specifically
to iPhone and has been certified by the developer to
meet Apple performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
English
|
29
Appendix
Function Item List
In Standby
In Tuner source
1st hierarchy
2nd hierarchy
3rd hierarchy
Page
15
16
“AUDIO CONTROL”(See in CD/Audio file source)
“DISP SELECT”
1st hierarchy
“DISP SELECT”
“SETTINGS”
2nd hierarchy
3rd hierarchy
Page
16
18
“SETTINGS”
“LOCAL SEEK”
“SEEK MODE”
“AUTO MEMORY”
“MONO SET”
“CLOCK”
“CLOCK”
“CLOCK ADJUST”
“DIMMER SET”
“TEXT SCROLL”
“BT DVC STATUS”
“DISPLAY”
10
17
“CLOCK ADJUST”
18
17
18
“INITIAL SET”
“PRESET TYPE”
“KEY BEEP”
“DISPLAY”(See in standby)
“DEMO MODE”
“TDF ALARM”
“BUILT-IN AUX”
“CD READ”
“SWITCH PREOUT”
“SP SELECT”
“F/W UP”
In Hands-Free BT mode
18
1st hierarchy
“DISP SELECT”
“SETTINGS”
2nd hierarchy
3rd hierarchy
Page
16
“PHONE SELECT”
“SMS DOWNLOAD”
“SMS INBOX”
“DEMO MODE”
18
In CD/ Audio file source
“VOICE TAG”
“DETAILED SET”
“DEVICE REGIST”
“S-DVC SELECT”
“DEVICE DELETE”
“PIN CODE EDIT”
“AUTO ANSWER”
“BT SP SELECT”
“CALL BEEP”
1st hierarchy
2nd hierarchy
3rd hierarchy
Page
“AUDIO CONTROL” “SUBWOOFER SET”
“BASS BOOST”
“SYSTEM Q”
20
“BASS LEVEL”
“MID LEVEL”
“TRE LEVEL”
“BT F/W UPDATE”
“MIC GAIN”
“NR LEVEL”
“EC LEVEL”
“CLOCK ADJUST”
“BALANCE”
“FADER”
“SUB-W LEVEL”
“DETAILED SET”
15
“LPF SUBWOOFER”
“SUB-W PHASE”
“SUPREME SET”
“CLOCK”
18
17
18
“DISPLAY”(See in standby)
“DEMO MODE”
“VOLUME OFFSET”
“DISP SELECT”
“SETTINGS”
16
18
17
18
In AUX source
“CLOCK”
“DISPLAY”(See in standby)
“CLOCK ADJUST”
1st hierarchy
2nd hierarchy
3rd hierarchy
Page
15
16
17
18
“AUDIO CONTROL”(See in CD/Audio file source)
“DISP SELECT”
“DEMO MODE”
In USB/ iPod source
“SETTINGS”
“AUX NAME SET”
“CLOCK”
1st hierarchy
“AUDIO CONTROL”(See in CD/Audio file source)
“DISP SELECT”
2nd hierarchy
3rd hierarchy
Page
15
16
“CLOCK ADJUST”
“DISPLAY”(See in standby)
17
18
“DEMO MODE”
“SETTINGS”
“SKIP SEARCH”
“MPLIST DELETE”
“CLOCK”
9
“CLOCK ADJUST”
18
17
18
“DISPLAY”(See in standby)
“DEMO MODE”
|
30 KDC-U546BT
Accessories/ Installation Procedure
with battery wires, the battery may die.
Accessories
•
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
1
2
3
4
•
•
•
..........1
..........2
..........4
..........4
•
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
Reception may drop if there are metal objects near the
Bluetooth antenna.
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
•
•
•
7. Reconnect the - battery.
8. Press the reset button.
Bluetooth antenna unit
For Good Reception
2WARNING
To assure good reception, note the following:
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
• Communicate with the cell-phone within the line-
of-sight distance of 10 m (30 ft). The communication
range becomes shorter depending on the
surrounding environment. The communication
range also becomes shorter when there is an
obstacle between this unit and the cell-phone. The
above maximum communication range (10 m) is
not always assured.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
• A broadcast station or walkie-talkie located nearby
can interfere with communication due to too strong
signal.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
•
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
English
|
31
Connecting Wires to Terminals
USB connector
AUX input (Stereo)
Use the mini-plug cable which is stereo type and
does not have any resistance.
FM/AM antenna input
Front output
R
L
Fuse (10A)
Rear output/Sub Woofer output
Switches the preout between rear output (“REAR”) and subwoofer
output (“SUB-W”). Refer to “SWITCH PREOUT” of <Initial Setting>
(page 18).
Wiring harness
(Accessory1)
White
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
If no connections are made, do not let the wire come out from the tab.
Depending on what antenna you are using, connect either to the control
Motor antenna control wire(Blue)
Mute control wire (Brown)
ANT. CONT
terminal of the motor antenna, or to the power terminal for the booster
amplifier of the film-type or short pole type antenna.
To connect the Kenwood navigation system, consult your navigation
manual.
MUTE
Steering remote control wire
(Light Blue/Yellow)
To use the steering wheel remote control feature, you need to an
exclusive remote adapter (not supplied) matches your car is required.
REMOTE CONT
STEERING WHEEL
REMOTE INPUT
Power control wire (Blue/White)
Connect either to the power control terminal when using the optional
power amplifier.
P.CONT
Car fuse
box
Ignition key
switch
Ignition wire (Red)
ACC
Car fuse box
(Main fuse)
Battery wire (Yellow)
Ground wire (Black) · (To car chassis)
Battery
+
–
|
32 KDC-U546BT
Installation/Removing the Unit
Non-Japanese Cars
Removing the Hard Rubber Frame
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
Lock
Catch
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Accessory2
⁄
Removal tool
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
2 When the upper level is removed, remove the
lower two locations.
⁄
•
The frame can be removed from the bottom side in the
same manner.
Japanese Cars
1 Refer to the section <Removing the Hard Rubber
Frame> and then remove the hard rubber frame.
Removing the Unit
2 Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and secure
the unit with the accessory screws.
1 Refer to the section <Removing the Hard Rubber
Frame> and then remove the hard rubber frame.
2 Detach the faceplate.
T
N
3 Insert the two removal tools deeply into the slots
T/N
on each side, as shown.
T
N
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
T: Toyota cars
N: Nissan cars
Accessory2
8 mm
MAX.
8mm
MAX.
3
4
ø5mm
ø5mm
Accessory3...for Nissan car
Accessory4...for Toyota car
¤
•
¤ CAUTION
Be careful to avoid injury from the catch pins on the
removal tool.
Install this unit in the console of your vehicle.
5 Pull the unit all the way out with your hands, being
Do not touch the metal part of this unit during and
shortly after the use of the unit. Metal part such as
the heat sink and enclosure become hot.
careful not to drop it.
English
|
33
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
Audio file source
? The sound skips when an Audio file is being
played.
!
• Cannot set up the subwoofer.
• Cannot set up the low pass filter.
• No output from the subwoofer.
• “SUBWOOFER SET” of <Audio Control> (page 15) is
not set to ON.
✔
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 3).
The recording condition is bad.
Record the media again or use another media.
☞
• Preout is not set to subwoofer.
☞ “SWITCH PREOUT” of <Initial Setting> (page 18).
Hands-free phoning
? The hands-free talk volume is low.
!
!
Cannot set up the subwoofer phase.
The Low Pass Filter is set to “THROUGH”.
☞ “LPF SUBWOOFER” of <Audio Control> (page 15).
✔
The hands-free talk volume is set at a low level.
☞
The hands-free talk volume can be adjusted
independently. Adjust it during hands-free
talk. “MIC GAIN”, “NR LEVEL” and “EC LEVEL” of
<Bluetooth Setup> (page 20).
The number of songs contained in “SONGS”
category of this unit is different from that
contained in “SONGS” category of iPod.
Podcast files are not counted in this unit as this unit
does not support the playback of podcast files.
? No sound is heard from the rear speakers.
You are talking in the hand-free talk mode.
✔
☞
No sound is heard from the rear speakers in the
hands-free talk mode.
? No beep is heard at reception of an incoming call.
✔
No beep is heard depending on the type of your
cell-phone.
What might seem to be a malfunction in your unit
may just be the result of slight miss operation or
miss wiring. Before calling service, first check the
following table for possible problems.
☞
The “CALL BEEP” of <Bluetooth Setup> (page 20)
is set to ON.
? Voice is not recognized.
✔
✔
✔
The vehicle window is open.
General
☞
If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows
to reduce noise.
? The operation check sound (beep sound) does not
sound.
✔
The preout jack is being used.
Small voice.
If voice is too small, it cannot be recognized
☞
The operation check sound (beep sound) cannot
be output for the preout jack.
☞
properly. Speak into the microphone a little more
loudly and naturally.
The person saying the voice tag is not the one who
registered the it.
Tuner source
? Radio reception is poor.
☞
Only the voice of the person who registered the
voice tag can be recognized.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
☞
Clean the CD, referring to the CD cleaning of the
section on <Handling CDs> (page 3).
The disc is severely scratched.
Try another disc instead.
☞
|
34 KDC-U546BT
NO MUSIC DATA/ERROR 15:
• The connected USB device contains no
The messages shown below display your
systems condition.
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
TOC ERROR:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
USB ERROR:
iPod ERROR:
Some trouble may have occurred to the
connected USB device.
➪ Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
ERROR 05:
ERROR 77:
The disc is unreadable.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
“ERROR 77” code does not disappear,
consult your nearest service center.
Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
IN (Blink):
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
USB REMOVE (Blink):
The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
NO NUMBER: • The calling party does not notify a caller ID.
• There is no phone number data.
PROTECT (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button. If
the “PROTECT” code does not disappear,
consult your nearest service center.
NO DATA:
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
NO ENTRY:
The cell-phone has not been registered
(pairing).
NA FILE:
An Audio file is played with a format that this
unit can’t support.
HF DISCONCT: The unit cannot communicate with the cell-
phone.
COPY PRO:
A copy-protected file is played.
HF ERROR 07: The memory cannot be accessed.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
READ ERROR: The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
HF ERROR 68: The unit cannot communicate with the cell-
phone.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
NO DEVICE:
N/A DEVICE:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
UNKNOWN:
The Bluetooth device cannot be detected.
DEVICE FULL: 5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
• An unsupported USB device is connected.
• Connection to the iPod has failed.
➪ Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 28) for information on supported
iPods.
PIN CODE NG: The PIN code is wrong.
CONNECT NG: The unit cannot be connected to the device.
PAIRING NG:
Pairing error.
English
|
35
Troubleshooting Guide
Specifications
NO MATCHING: The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
FM Tuner Section
Frequency Range
: 87.9 MHz – 107.9 MHz (200 kHz Space)
: 87.5 MHz – 108.0 MHz (50 kHz Space )
Usable Sensitivity (S/N = 26dB)
: 11.2 dBf (1.0 μV/75 Ω)
TOO SOFT:
TOO LOUD:
TOO LONG:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
The word or utterance is too long to be
recognized.
Quieting Sensitivity (DIN S/N = 46dB)
: 19.2dBf (2.5 μV/75 Ω)
Frequency Response ( 3 dB)
NO PHONEBOOK:
Data is not contained in the phone book.
: 30 Hz – 15 kHz
Signal to Noise Ratio (MONO)
: 63 dB
NO MESSAGE: No short message in In Box.
Stereo Separation (1 kHz)
: 40 dB
NO RECORD: The voice tag is not registered in the phone
book.
MEMORY FULL: The number of voice tags reaches the
maximum number to be registered in the
phone book.
AM Tuner Section
Frequency Range
Band1 (MW) : 530 kHz – 1700 kHz (10 kHz Space)
: 531 kHz – 1611 kHz (9 kHz Space)
Band2 (SW1) : 2940 kHz – 7735 kHz (5 kHz Space)
NO ACCESS:
The procedure preset with mixed preset
memory function cannot be available.
The preset content may not be recalled
depending on the selected band.
Band3 (SW2) : 9500 kHz – 10135 kHz / 11580 kHz
- 18135 kHz (5 kHz Space)
NO VOICE:
No call.
Usable Sensitivity (S/N = 20dB)
MW : 31 dBμ (36 μV)
SW : 32 dBμ (40 μV)
CD Player Section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle Speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency Response ( 1 dB)
: 20 Hz – 20 kHz
Total Harmonic Distortion (1 kHz)
: 0.01 %
Signal to Noise Ratio (1 kHz)
: 105 dB
Dynamic Range
: 93 dB
MP3 Decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA Decode
: Compliant with Windows Media Audio
|
36 KDC-U546BT
USB Interface
General
USB Standard
: USB1.1/ 2.0 (Full Speed)
Operating Voltage
: 14.4 V (10.5 – 16V allowable)
File System
: FAT16/ 32
Maximum Current Consumption
: 10 A
MP3 Decode
: Compliant with MPEG-1/2 Audio Layer-3
Installation Size (W x H x D)
: 182 x 53 x 155 mm
WMA Decode
: Compliant with Windows Media Audio
Weight
: 1.3 kg
Maximum Supply Current
: 500 mA
Bluetooth Section
Version
: Bluetooth Ver. 2.0 Certified
Frequency Range
: 2.402 – 2.480 GHz
Output Power
: +4dBm (MAX), 0dBm (AVE) Power Class 2
Maximum Communication Range
: Line of sight approx.10m (32.8 ft)
Profile
: HFP (Hands Free Profile)
: HSP (Headset Profile)
: SPP (Serial Port Profile)
: PBAP (Phone book Access Profile)
: OPP (Object Push Profile)
: SYNC (Synchronization Profile)
Audio Section
Maximum Output Power
: 50 W x 4
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
Speaker Impedance
: 4 – 8 Ω
Tone Action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout Level / Load (CD)
: 2000 mV/10 kΩ
Preout Impedance
: ≤ 600 Ω
Auxiliary Input
Frequency Response ( 3 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
Specifications subject to change without notice.
English
|
37
目录
使用之前
39
40
41
其他功能
54
56
时钟调节
演示模式设定
初始设定
拆卸面板
本机的复位方法
各部分的名称和功能
一般操作
使用之前
共通操作
功能设定操作
Bluetooth设置
Bluetooth设置
音乐光盘/音频文件/iPod的操作
42
登录Bluetooth装置 (配对)
删除登录的Bluetooth装置
登录PIN代码
显示固件版本
下载电话簿
基本操作方法
播放功能
全部随机播放
音乐搜索
搜索iPod中的音乐
字符搜索
选择需要连接的Bluetooth装置
下载短信
iPod的播放列表
音频文件/iPod设定
iPod手动控制模式
直接搜索音乐
SMS (短信服务)
添加语音拨号指令
对分类设定语音指令
遥控器的基本操作
附录
62
64
67
68
69
70
72
调谐器的操作方法
46
48
基本操作方法
电台预设存储
调谐器设定
直接调谐
附件/安装步骤
将导线与端子连接
本机的安装/拆卸方法
故障检修
设定频率步进
免提通话的操作
连接Bluetooth装置
拨打电话
拨打电话簿中的号码
拨打通话记录中的号码
拨号
规格
进行语音拨号通话
登录预设拨号 (预设存储)
快速拨号 (预设拨号)
接听电话
在通话中
通话等候
其他功能
电话号码类型 (分类) 的显示
音响调节
51
52
音响控制
显示设定
显示的选择
文本滚动
显示设定
辅助输入显示设定
|
38 KDC-U546BT
使用之前
说明
2警告
·安装发生困难时，请与建伍经销商洽谈。
为了防止受伤和火灾，请遵守下列注意事项：
·当购买选购附件时，请与建伍经销商洽谈，确认选
购附件是否适合您的机型以及能否在您的地区使
用。
为了防止短路等事故，请勿将金属物品 (硬币、工具
等) 掉落在装置中。
·本机可以显示的字符为A-Z 0-9 @ " ‘ ` % & * + – = , . /
\ < > [ ] ( ) : ; ^ - { } | ~。
在首次使用本机之前
本机在出厂时被设定为演示模式。
·在本说明书中采用的显示和面板的插图是为了更加
明确地举例说明控制的使用方法。因此，在插图中
出现的显示可能与实际装置的显示有所不同，并且
某些显示的插图可能不适用。
首次使用本机时，请取消演示模式。请参照＜退出演
示模式＞(第41页)。
装置的保养
如果本机的面板被弄脏，请使用硅布等干燥的软布擦
拭清洁。如果面板很脏，请蘸中性清洁剂擦拭污垢，
然后擦去清洁剂。
CD的使用
·手持CD时，请不要触摸CD的记录面。
·请勿向CD粘贴胶带等。并且请不要使用粘贴了胶
带的CD。
¤
·请不要使用光盘用附件。
对本机直接喷洒清洁剂将可能使得机械部件受到影响。使用
硬质的布或者使用诸如稀释剂或酒精等挥发性溶剂擦拭面板
将划伤表面或者将字符擦掉。
·请从光盘的中心向外侧擦拭。
·将CD从本机中取出时，请向水平方向拉出。
·当CD的中心孔以及外侧圆周部位有毛刺时，请使
关于本机和面板的端子
用圆珠笔等将毛刺去除，然后再使用。
·为了防止劣化，请不要用手触摸本机和面板的端子。
·装置或面板端子脏污时，请使用软布擦拭。
无法使用的CD
·无法使用圆形以外的CD。
透镜雾气
在寒冷的天气使用汽车暖气时，本机的CD播放器透镜
可能凝聚结露，称为透镜雾气，透镜上的结露可能影
响CD的播放。这时，请取出光盘等候结露蒸发。如果
在等一会后本机仍然无法正常运行，请与当地的建伍
经销商洽询。
·无法使用记录面著色的CD以及肮脏的CD。
·本机仅能够播放具备下列标志
的CD。
对于没有这些标志的CD，本机可能无法正常播放。
·没有进行过最终处理的CD-R以及CD-RW无法播
放。(有关最终处理的详细内容，请参照所使用的
CD-R/CD-RW记录软件和CD-R/CD-RW记录器的使用
说明书。)
·无法使用3英寸CD。如果试图使用适配器插入将导
致故障。
|
中文
39
各部分的名称和功能
1
2
3
4
5
15 14 13 12 11
10
9
8
7
6
1 释放按钮
p [
选择电台、歌曲以及设定项目。
q 麦克风
4
] / [
¢
] 按钮
本机的面板可以拆下带走，便于防盗。
请参照＜拆卸面板＞(第55页)。
2 [SRC] 按钮
本机内设麦克风用于免提通话。如果因麦克风
音量较低、车内噪音或回音的影响而无法识别语
音，请选择＜Bluetooth设置＞(第56页) 的 "MIC
GAIN" (麦克风增益)、"NR LEVEL" (降低噪音等
级) 或 "EC LEVEL" (回音等级) 调节麦克风设
定。
接通本机电源和选择信号源。
切断本机电源 (按下该按钮1秒钟以上)。
3 光盘槽
插入光盘后 (标签面朝上)，信号源自动切换，开
始播放歌曲。
w [VOL] 旋钮
4 显示窗
调节音量。
5 [0] 按钮
进入功能设定模式和设定项目 (转动和按下该
旋钮)。
有关详细内容，请参照＜功能设定操作＞(第41
页)。
弹出光盘。
选择拆除模式，拆除USB装置或iPod (按下该按
钮2秒钟以上)。
6 USB端子
e [BAND] 按钮
连接时打开USB端子盖，可连接USB装置或
iPod。
选择接收波段、文件夹或音频文件。
r [
] 按钮
7 辅助输入端子
返回至前一个项目。
可以使用微型插头 (直径3.5mm) 连接携带式音
响装置。
·请使用无阻抗的立体声微型插头导线。
t [
] 按钮
进入音乐搜索模式。
进入拨号模式。
8 [1] － [6] 按钮
呼出存储的电台。
在音乐光盘、音频文件以及iPod之间切换播放
模式。
9 [VOICE] 按钮
使用语音拨号通话。
变更文本滚动显示。(按下1秒钟以上)
|
40 KDC-U546BT
一般操作
使用之前
功能设定操作
使用本功能进行基本操作的方法说明如下所示。
各功能项目将在操作方法中说明。
退出演示模式
安装后第一次使用本机时，请取消演示模式。
1 选择信号源
1
在显示 "CANCEL DEMO"、"PRESS"、"VOLUME KNOB"
时 (约15秒)，请按下 [VOL] 旋钮取消演示模式。
按下 [SRC] 按钮。
各信号源的功能项目各不相同。有关功能项目的列
表，请参照＜功能项目列表＞(第66页)。
2 转动 [VOL] 旋钮选择 "YES" (是)，然后按下 [VOL]
旋钮。
2 进入功能设定模式
⁄
按下 [VOL] 按钮1秒钟以上。
显示 "FUNCTION"。
·也可以使用＜演示模式设定＞(第54页) 设定或取消
演示模式。
3 选择需要的功能项目
转动 [VOL] 旋钮，在显示需要的项目时按下。
重复上述操作，直到选择了需要的功能。
共通操作
⁄
按下 [ ] 按钮返回至前一个项目。
选择电源和信号源
例：
按下 [SRC] 按钮接通电源。
ꢂ
ꢁ
每次按下 [SRC] 按钮，即在信号源之间切换。
调谐器 ("TUNER") ➜ USB 或 iPod ("USB" 或 "iPod")
➜CD("CD")➜辅助输入("AUX")➜待机("STANDBY")
按下 [SRC] 按钮1秒钟以上，电源切断。
ꢀ
ꢂ
ꢁ
AUDIO CONTROL
BASS BOOST
ꢀ
ꢀ
ꢂ
[VOL]
[VOL]
ꢁ
DETAILED SET
SUPREME SET
⁄
·当识别了连接iPod时，信号源的显示从 "USB" 变成
"iPod"。
DISP SELECT
SETTINGS
·各信号源的播放准备就绪时，可以选择 "CD" 和 "iPod"
信号源。
在本使用说明书中，上述选择表示为
选择 "AUDIO CONTROL" (音响控制)
音量
＞
"DETAILED
转动 [VOL] 旋钮调节音量。
SET" (详细设定)
＞
"SUPREME SET" (SUPREME设定)。
4 进行设定
转动 [VOL] 旋钮选择设定值，然后按下 [VOL] 旋钮。
5 退出功能设定模式
按下 [
] 按钮1秒钟以上。
|
中文
41
音乐光盘/音频文件/iPod的操作
光盘槽
[SRC] [VOL]
[ꢀ]
CA-U1EX
·连接USB装置时需要使用CA-U1EX
(选购附件)。
·连接iPod时需要使用KCA-iP101
(选购附件)。
ꢁ E
[ ] / [ ]
[
] [
]
[BAND]
[1] [6] USB端子
—
基本操作方法
播放功能
播放光盘
扫描播放
将光盘插入光盘槽 (标签面朝上)。
插入后信号源自动切换，开始播放歌曲。
插入光盘后，"IN" 指示点亮。
按下 [2] 按钮。
连续播放光盘或文件夹中的音乐开头部分。
扫描播放接通时，显示 "TRACK SCAN" (音轨扫描)/
"FILE SCAN" (文件扫描)。
再次按下该按钮，从当前播放的歌曲开始，以通常
模式播放。
播放USB装置或iPod
将USB装置或iPod与USB端子连接。
连接后信号源自动切换，开始播放歌曲。
⁄
暂停和播放
·播放iPod时，无法进行扫描播放操作。
按下 [6] 按钮，暂停、或恢复播放 (音轨或文件)。
随机播放
按下 [3] 按钮。
随机播放光盘或文件夹中的音乐。
随机播放接通时，显示 "DISC RANDOM" (光盘随机
播放)/ "FOLDER RANDOM" (文件夹随机播放)。
再次按下该按钮，随机播放取消。
选择文件夹
按下 [BAND] 按钮切换文件夹。
只有在搜索模式选择了分类后才能操作iPod。
选择歌曲
按下 [4] 或 [¢] 按钮选择歌曲 (音轨或文件)。
按下 [4] 或 [¢] 按钮可使音乐快退或快进。
(在播放音响文件时，无声音输出。)
重复播放
按下 [4] 按钮。
如果在播放CD时按下，即在音轨重复播放 ("TRAC
REPEAT") 和重复播放切断 ("REPEAT OFF") 之间
切换。
弹出光盘
按下 [0] 按钮弹出光盘。
关闭汽车发动机后，在10分钟之内可以弹出光盘。
如果在播放音频文件时按下，即在文件重复播放
("FILE REPEAT")、文件夹重复播放 ("FOLD REPEAT"/
"FOLDER REPEAT") 和重复播放切断 ("REPEAT OFF")
之间切换。
拆除USB装置或iPod
按下 [0] 按钮2秒钟以上，进入USB装置拆除模式
(显示 "USB REMOVE")，然后可以安全拆除USB装
置或iPod。
选择CD、USB或iPod信号源
按下 [SRC] 按钮。
选择 "CD"/"USB" 或 "iPod" 显示。
|
42 KDC-U546BT
· * 本操作仅对在使用 KENWOOD Music Editor (音乐
编辑器)制作的数据库中登录的文件有效。
iPod的功能
全部随机播放
随机播放iPod中的全部歌曲。
iPod的功能
按下 [3] 按钮1秒钟以上。
按下该按钮即在全部随机播放接通 ("ALL RANDOM")
和切断 ("RANDOM OFF") 之间切换。再次按下该按
钮，随机播放取消。
搜索iPod中的音乐
搜索需要播放的歌曲 (在iPod中)。
1 进入音乐搜索模式
⁄
·根据iPod中歌曲的数量，接通全部随机播放功能可
能需要较长时间。
按下 [
] 按钮。
显示 "SEARCH"。
·接通全部随机播放功能后，iPod的浏览项目即切换
到 "SONGS" (歌曲)。即使切断全部随机播放功能，
该浏览项目也不会改变。
2 搜索音乐
操作种类
操作
·全部随机播放功能接通时，如果变更浏览项目搜索
音乐，则全部随机播放功能切断，随机播放浏览项
目中的歌曲。
在项目之间移动
转动 [VOL] 旋钮。
按下 [4] 或 [¢] 按钮。
按下 [VOL] 旋钮。
跳跃搜索
选择项目
返回前一个项目
返回至首页选单
按照字符搜索
按下 [
] 按钮。
按下 [BAND] 按钮。
音频文件/CD信号源的功能
按下 [
(第44页)。
] 按钮。请参照＜字符搜索＞
音乐搜索
从装置或正在播放的媒体中选择需要欣赏的音乐。
取消音乐搜索模式
按下 [
] 按钮1秒钟以上。
1 进入音乐搜索模式
按下 [
] 按钮。
⁄
显示 "SEARCH"。
显示当前的音响文件名称。
·跳跃搜索：跳跃的歌曲数取决于选择的列表中歌曲
总数的百分比。通过＜音频文件/iPod设定＞(第45
页) 中的 "SKIP SEARCH" (跳跃搜索) 设定百分比。
2 搜索音乐
音响文件
按下 [
跃歌曲，而与设定无关。
4] 或 [¢] 按钮3秒钟以上，即按照10％跳
·如果歌曲名称中不含可显示的字符，则显示浏览项
目名称和数字。
操作种类
在文件夹/文件之间移动
操作
转动 [VOL] 旋钮。
项目
显示
项目
播客
显示
跳跃搜索*
按下 [4] 或 [¢] 按钮。
按下 [VOL] 旋钮。
播放列表
艺术家
专辑
"PLIST***"
"ART***"
"ALB***"
"PRGM***"
"PDCT***"
"GEN***"
"COM***"
选择文件夹/文件
返回到前一个文件夹
返回到根文件夹
流派
按下 [
] 按钮。
作曲家
按下 [BAND] 按钮。
歌曲
在文件夹名称旁显示的 "＜" 或 "＞" 表示该文件夹
位于其他文件夹之前或之后。
CD信号源
操作种类
操作
在音轨之间移动
选择音轨
转动 [VOL] 旋钮。
按下 [VOL] 旋钮。
选择音轨前，按下 [BAND] 按钮。
返回第一音轨
取消音乐搜索模式
按下 [
] 按钮1秒钟以上。
⁄
·跳跃搜索：跳跃的歌曲数取决于选择的列表中歌曲
总数的百分比。通过＜音频文件/iPod设定＞(第45
页) 中的 "SKIP SEARCH" (跳跃搜索) 设定百分比。
按下 [
跃歌曲，而与设定无关。
4] 或 [¢] 按钮3秒钟以上，即按照10％跳
|
中文
43
音乐光盘/音频文件/iPod的操作
iPod的功能
⁄
·
字符搜索
使用存储在一个iPod中的歌曲制作播放列表。如果试
图登录存储在其他iPod中的歌曲，则出现 "NO INFO"
(无信息)，然后出现 "MPLIST DELETE" (播放列表的
删除)。删除播放列表时，转动 [VOL] 旋钮选择 "YES"
(是)，然后按下 [VOL] 旋钮。
可以按照字符选择歌曲。
本功能在选择的浏览项目 (艺术家、专辑等) 列表中，
搜索歌名包含指定字符的歌曲。
·对于在音乐搜索模式下显示的歌曲，也可以按照相
同的方法登录。关于如何使用音乐搜索功能，请参
照＜搜索iPod中的音乐＞(第43页)。
·如果试图登录第11首歌曲，则出现 "MEMORY FULL"
(存储器存满) 而无法登录。如果需要登录歌曲，请
删除不需要的歌曲。
1 进入音乐搜索模式
按下 [
] 按钮。
显示 "SEARCH" (搜索)。
2 进入字符搜索模式
按下 [
] 按钮。
·请不要登录播客。否则可能登录不需要登录的歌曲
或无法正常播放。
显示 "SEARCH ＜_ _ _＞"。
3 选择需要搜索的字符
播放在播放列表中的歌曲
操作种类
操作
1 显示播放列表
选择字符
转动 [VOL] 旋钮。
按下 [5] 按钮。
将光标移动到输入字符的位置
按下 [4] 或 [¢] 按钮。
显示 "MY PLAYLIST" (播放列表)。
最多可以输入3个字符。
2 播放在播放列表中的歌曲
转动 [VOL] 旋钮选择需要播放的歌曲，然后按下
[VOL] 旋钮。
4 确定选择的字符
按下 [VOL] 旋钮。
开始搜索。搜索结束后，在选择的字符位置，再次
选择音乐搜索模式。
⁄
·切断电源可停止播放在播放列表中的歌曲。
·如果在一首歌曲的结束没有1秒钟或更长的无声时
间，则可能无法播放该歌曲的结束部分。
取消字符搜索模式
按下 [
] 按钮1秒钟以上。
⁄
从播放列表中删除歌曲
· 根据歌曲的数量或iPod中播放列表的数量，字符搜
索可能需要较长时间。
1 转动 [VOL] 旋钮显示需要删除的歌曲，然后按下
· 如果搜索A至Z和0至9以外的字符，应在第一字符位
置输入 "*"。这时，不能在第二和第三字符位置输入
任何字符。
· 对于字母搜索模式，如果第一个字符串以冠词 "a"、
"an" 或 "the" 开始，搜索将忽略该冠词。
[VOL] 旋钮2秒钟以上。
2 转动 [VOL] 旋钮选择 "ONE" (一首) 或 "ALL" (全部)，
然后按下 [VOL] 旋钮。
选择 "DELETE ALL" (全部删除) 可删除全部歌曲。
3 转动 [VOL] 旋钮选择 "YES" (是)，然后按下 [VOL]
旋钮。
iPod的功能
显示 "COMPLETE"。
iPod的播放列表
⁄
可以在本机的播放列表中登录喜爱的歌曲。在播放列
表中可最多登录10首歌曲。
·选择在＜音频文件/iPod设定＞(第45页) 中说明的
"MPLIST DELETE" (播放列表的删除)，也可以删除
播放列表中的全部歌曲。
在播放列表中登录歌曲
1 播放需要登录的歌曲
按下 [BAND]、[4] 和 [¢] 按钮。
请参照＜搜索iPod中的音乐＞(第43页) 选择播放的
歌曲。
2 登录歌曲
按下 [5] 按钮2秒钟以上。
显示 "## STORED (登录号码)"。
可最多登录10首歌曲。
|
44 KDC-U546BT
遥控器的功能
音频文件/iPod设定
直接搜索音乐
可以选择以下设定项目。
输入音轨号码搜索音乐。
1 进入功能设定模式
按下 [VOL] 旋钮1秒钟以上。
显示 "FUNCTION" (功能)。
1 进入直接搜索音乐模式
按下 [DIRECT] 按钮。
2 选择功能项目
2 输入音乐号码
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "SETTINGS" (设定) ＞ 功能项目。
按下数字按钮。
3 搜索音乐
功能项目
"SKIP SEARCH"
(跳跃搜索)
可选设定/项目
按下 [4] 或 [¢] 按钮。
跳跃的歌曲数取决于选择的列表中歌曲总数
的百分比。(仅限iPod和建伍音乐编辑器文件)
0.5%/1%/5%/10%
取消直接搜索音乐
按下 [
] 按钮。
"MPLIST DELETE"
(删除播放列表)
删除存储的播放列表。
＜iPod的播放列表＞(第44页) (仅限iPod)
NO/YES
⁄
·播放iPod、"Music Editor" (音乐编辑器) 媒体、随机
播放或扫描播放时，无法进行直接搜索音乐。
(出厂设定：加下划线)
3 进行设定
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "MPLIST DELETE" (播放列表的删除) 时：
转动 [VOL] 旋钮选择 "YES" (是)，然后按下 [VOL]
旋钮。
删除存储的播放列表。
4 退出功能设定模式
按下 [
] 按钮1秒钟以上。
iPod的功能
iPod手动控制模式
可以通过iPod的控制操作iPod。
按下 [1] 按钮。
按下该按钮，即在iPod手动控制模式接通 ("HANDS
ON") 和切断 ("HANDS OFF") 之间切换。
⁄
·在iPod手动控制模式，无法使用本机操作iPod。
·本模式不兼容音乐信息显示。将显示 "iPod MODE"
(iPod模式)。
·如果iPod符合iPod控制功能，则可以操作iPod。
|
中文
45
调谐器的操作方法
调谐器设定
[SRC] [VOL]
可以选择以下调谐器设定项目。
1 选择调谐器信号源
按下 [SRC] 按钮。
选择 "TUNER" (调谐器) 显示。
2 进入功能设定模式
按下 [VOL] 旋钮1秒钟以上。
显示 "FUNCTION" (功能)。
ꢁ
E
]
[
]
[BAND]
[
] / [
—
[1] [6]
3 选择功能项目
基本操作方法
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "SETTINGS" (设定) ＞ 功能项目。
选择调谐器信号源
功能项目
可选设定/项目
按下 [SRC] 按钮。
"LOCAL SEEK"
(本地搜索)
自动搜索调谐只搜索接收良好的电台。
(仅限AM波段)
OFF(切断)/ON(接通)
选择 "TUNER" 显示。
选择接收波段
按下 [BAND] 按钮。
每次按下该按钮，接收波段即在FM1、FM2、FM3、
MW、SW1和SW2之间切换
"SEEK MODE"
(搜索模式)
选择接收装置的调谐模式。
AUTO1: 自动搜索电台。
AUTO2: 按照预设存储器中的电台顺序
搜索。
选择接收电台
按下 [4] 或 [¢] 按钮。
接收立体声电台时，"ST" 指示点亮。
MANUAL: 通常的手动调谐控制。
"AUTO MEMORY"*
(自动存储)
自动存储接收状态良好的电台。
NO/YES
"MONO SET"
(单声道设定)
当立体声广播作为单声道接收时，可以减
少噪音。(仅限FM波段)
OFF(切断)/ON(接通)
选择预设电台
按下 [1] － [6] 按钮。
(出厂设定：加下划线)
4 进行设定
电台预设存储
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "AUTO MEMORY" (自动存储输入) 时：
转动 [VOL] 旋钮选择 "YES" (是)，然后按下 [VOL]
旋钮。
向存储器输入电台。
1 选择存储的频率
按下 [4] 或 [¢] 按钮。
存储了6个可接收的电台后，自动存储输入关闭。
2 选择存储的号码
5 退出功能设定模式
按下 [1] － [6] 按钮2秒钟以上。
按下 [
] 按钮1秒钟以上。
⁄
⁄
· 根据＜初始设定＞(第54页) 的 "PRESET TYPE" (预设
类型) 设定，最多可向 [1] － [6] 按钮存储6个不同
波段 (FM/MW/SW) 的电台。
·* 对＜初始设定＞(第54页) 的 "PRESET TYPE" (预设
类型) 选择了 "TYPE NORMAL" (普通型) 时，可以
完成本设定。
|
46 KDC-U546BT
遥控器的功能
直接调谐
输入频率直接调谐需要的广播电台。
1 进入直接调谐模式
按下 [DIRECT] 按钮。
显示 "- - - -"。
2 输入频率
按下数字按钮。
例：
所需频率
按键
92.1 MHz (FM)
810 kHz (AM)
[9], [2], [1]
[8], [1], [0]
3 调谐输入的频率
按下 [4] 或 [¢] 按钮。
取消直接调谐
按下 [
] 按钮。
⁄
·可以输入的FM波段频率的最小单位是0.1MHz。
设定频率步进
改变调谐频率步进。
FM波段的初始设定为50kHz，MW波段的初始设定为
9kHz。
1 切断电源
按下 [SRC] 按钮1秒钟以上。
2 切换频率步进
在按下 [1] 和 [5] 按钮的同时按下 [SRC] 按钮。
出现显示后松开按钮。
FM波段的频率步进变成200kHz，MW波段变成
10kHz。
⁄
·重复相同的操作时，频率步进恢复到初始设定。
·变更频率步进后，存储的频率被删除。
|
中文
47
免提通话的操作
拨打电话
[SRC] [VOL]
可以选择以下拨号方法。
1 进入Bluetooth模式
按下 [VOL] 旋钮。
显示 "BT MODE" (Bluetooth模式)。
2 进入拨号方法模式
按下 [
] 按钮。
ꢁ
E
]
—
[
][ ][BAND]
[
] / [
[VOICE] [1] [6]
显示 "PHONE BOOK" (电话簿)。
3 选择拨号方法
连接Bluetooth装置
转动 [VOL] 旋钮，在显示需要的项目时按下。
使用Bluetooth装置之前，需要建立Bluetooth装置与本
机的连接。以下为三个必要步骤。
显示
概述
"PHONE BOOK"
"OUT-CALL"
"IN-CALL"
在电话簿中选择需要搜索的首字母和姓名。
拨打拨出通话列表中的号码。
拨打来电通话列表中的号码。
拨打未接听电话列表中的号码。
输入电话号码拨打电话。
第一步 配对 (从Bluetooth装置侧登录)
为了本机能够使用您的Bluetooth装置 (手机)，需要
进行登录 (配对)。
"MISSED CALLS"
"NUMBER DIAL"
1 接通本机电源。
各种模式的操作方法将在以下说明。
按下 [SRC] 按钮。
4 退出拨号方法模式
2 操作Bluetooth装置，开始向本机登录
操作Bluetooth装置，向免提装置登录 (配对)。
从连接的装置列表中，选择 "KENWOOD BT CD/R-
3P1"。
按下 [
] 按钮1秒钟以上。
中断通话
按下 [SRC] 按钮。
3 输入PIN代码
在Bluetooth装置输入PIN代码 ("0000")。
确认Bluetooth装置的登录是否完成。PIN代码的初
始值设定为 "0000"。可以变更该代码。
请参照＜登录PIN代码＞(第58页)。
拨打电话簿中的号码
1 选择电话簿模式
关于如何选择拨号方法，请参照＜拨打电话＞(第
48页)。
4 操作Bluetooth装置，开始免提连接。
选择 "PHONE BOOK" 显示。
第二步 连接
2 选择需要搜索的首字母
如果已经登录了两部或更多部手机，需要选择其中
的一部手机。有关详细内容，请参见＜选择需要连
接的Bluetooth装置＞(第59页)。
操作种类
操作
移动到相邻的字符。
移动到相邻的一行。
确定选择的首字母。
转动 [VOL] 旋钮。
按下 [BAND] 按钮。
按下 [VOL] 旋钮。
手机连接后，"BT" 指示点亮。
第三步 免提通话
建立了连接后，就可以进行免提通话。
⁄
·从本机侧登录时，请参照＜登录Bluetooth装置＞(第
57页)。
·有关Bluetooth手机免提功能的详细内容，请参照＜关
于手机＞(第65页)。
|
48 KDC-U546BT
3 选择姓名
操作种类
⁄
·可以最多输入25位号码。
操作
移动到下一个电话号码。
转动 [VOL] 旋钮。
移动到下一个姓名。
按下 [4] 或 [¢] 按钮。
进行语音拨号通话
4 通话
按下 [VOL] 旋钮。
1 进入语音识别模式
按下 [VOICE] 按钮。
⁄
显示 "V-RECG READY" (语音识别准备就绪)。
·为了使用电话簿，必须事前下载到本机。
请参照＜下载电话簿＞(第58页)。
·在搜索中，对于诸如 "u" 的重音字符，按照 "ü" 等无
重音字符搜索。
2 按下 [VOL] 旋钮。
显示 "PB NAME"。
听到提示音后，请在2秒钟之内说出姓名。
3 显示 "PN TYPE"。
听到提示音后，请在2秒钟之内说出分类。
拨打通话记录中的号码
4 通话
按下 [VOL] 旋钮。
1 选择通话记录模式
移动到下一个电话号码
转动 [VOL] 旋钮。
关于如何选择拨号方法，请参照＜拨打电话＞(第
48页)。
选择 "OUT-CALL" (拨出通话) 显示、"IN-CALL" (来
电通话) 显示、或 "MISSED CALLS" (未接听电话)
显示。
⁄
·如果语音没有被识别，则显示消息。按下 [VOL] 旋
钮，可以再次输入语音。(第71页)
2 选择姓名或电话号码
·姓名和分类均需要登录语音标签。(第60页)
·进行语音识别时，不输出音响。
转动 [VOL] 旋钮。
3 通话
按下 [VOL] 旋钮。
登录预设拨号 (预设存储)
⁄
·拨出通话列表和来电通话列表以及未接听电话列表
是由本机拨出的和接收的通话。这不是存储在手机
存储器中的通话。
1 输入需要登录的电话号码
参照以下内容输入电话号码:
拨号/拨打通话记录中的号码/拨打电话簿中的号码
2 选择存储的号码
按下 [1] － [6] 按钮2秒钟以上。
拨号
1 选择拨号模式
关于如何选择拨号方法，请参照＜拨打电话＞(第
48页)。
选择 "NUMBER DIAL" 显示。
2 输入电话号码
操作种类
操作
选择号码。
转动 [VOL] 旋钮。
按下 [¢] 按钮。
按下 [4] 按钮。
移动到下一位。
删除最后一位。
· 按下遥控器上的数字 ([1]－[0])、#([FM])、
* ([AM]) 或 +([¢]) 按钮。
3 通话
· 按下 [VOL] 旋钮。
· 按下遥控器上的 [OK] 按钮。
|
中文
49
免提通话的操作
快速拨号 (预设拨号)
通话等候
1 选择需要从存储器中呼出的号码
暂停当前的通话，接听其他来电
按下 [1] － [6] 按钮。
1 按下 [VOL] 旋钮。
2 通话
2 转动 [VOL] 旋钮，在显示需要的项目时按下。
按下 [VOL] 旋钮。
选择 "ANSWER" (接听)。
⁄
中断当前的通话，接听其他来电
按下 [SRC] 按钮。
·需要登录预设拨号号码。
继续当前的通话
1 按下 [VOL] 旋钮。
接听电话
2 转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "REJECT" (拒接)。
接听电话
按下 [VOL] 旋钮。
中断当前的通话，接听等候的通话
按下 [SRC] 按钮。
⁄
·以下操作将挂断电话：
在当前的通话和等候的通话之间切换
按下 [VOL] 旋钮。
- 插入CD。
- 连接USB装置。
每次按下该旋钮，切换通话的对方。
·如果已经在电话簿中登录，将显示通话对方的姓
名。
拒接来电
按下 [SRC] 按钮。
其他功能
清除中断连接的消息
按下 [VOL] 旋钮。
"HF DISCONCT" 消失。
在通话中
切换显示模式
中断通话
按下 [SRC] 按钮。
按下 [
] 按钮。
每次按下该按钮，即在姓名和电话号码之间切换。
切换到专用模式
按下 [6] 按钮。
每次按下该按钮，即在专用通话 ("PRIVATE TALK")
和免提通话之间切换。
电话号码类型 (分类) 的显示
电话簿中的分类项目显示如下所示。
⁄
显示
"GE"
信息
共同
·某些型号的手机在切换到专用通话模式时可能选择
在开始免提通话之前使用的装置。如果发生这种现
象，操作本机将无法切换回免提通话模式。请操作
手机恢复到免提通话模式。
"HM"
"OF"
自家
办公室
手机
"MO"
"OT"
在通话时调整音量
转动 [VOL] 旋钮。
其他
|
50 KDC-U546BT
音响调节
"SUB-W LEVEL"
(重低音扬声器电平)
可以设定重低音扬声器电平。
-15 — 0 — +15
[SRC] [VOL]
"DETAILED SET"
(详细设定)
移动到详细项目
"LPF SUBWOOFER" 选择重低音扬声器输出的截止频率。
(重低音扬声器低通 85/120/160/THROUGH (OFF) Hz
滤波器)
"SUB-W PHASE"
选择重低音扬声器输出的相位。
(重低音扬声器相位) REVERSE (180°) (反相)/
[
]
NORMAL (0°) (标准)
"SUPREME SET"
(SUPREME设定)
接通/切断Supreme功能。
OFF(切断)/ON(接通)
音响控制
"VOLUME OFFSET" 对各个音源的音量可以进行与基本音量不
可以调节以下音响控制项目。
(音量偏置)
同的设定。
-8 — 0 (AUX: -8 —0 — +8)
1 选择信号源
(出厂设定：加下划线)
按下 [SRC] 按钮。
4 进行设定
选择 "TUNER" (调谐器)/"USB"/"iPod" 或 "CD"/"AUX"
(辅助) 显示。
转动 [VOL] 旋钮，在显示需要的项目时按下。
2 进入功能设定模式
5 退出功能设定模式
按下 [VOL] 旋钮1秒钟以上。
显示 "FUNCTION" (功能)。
按下 [
] 按钮1秒钟以上。
⁄
·SUPREME：
对于使用低位速率 (低于128kbps、取样频率为44.1kHz)
编码压缩的高频区域，采用专有运算法则进行推断和
补充的技术。
根据位速率，通过压缩格式 (MP3或WMA) 实现最佳
补充和处理。
3 选择功能项目
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "AUDIO CONTROL" (音响控制)
目、或者选择 "AUDIO CONTROL" (音响控制)
"DETAILED SET" (详细设定) 功能项目。
＞
功能项
＞
＞
功能项目
"SUBWOOFER SET"
(重低音扬声器设定)
可选设定/项目
接通/切断重低音扬声器输出。
OFF(切断)/ON(接通)
对于使用高位速率、可变位速率编码的或具有最小
限度高频范围的音乐，该效果不明显。
"BASS BOOST"
(低音提升)
选择低音提升设定模式。
OFF/LV1/LV2 (根据设定，指示点亮。)
"SYSTEM Q"
(系统Q值)
在以下预设均衡器曲线之间切换。系统Q
值设定为除"NATURAL" (自然) 以外的EQ模
式时，"EQ" 指示点亮。
NATURAL (自然音乐)/USER (用户设定)/
ROCK (摇滚乐)/POPS (流行音乐)/
EASY (通俗音乐)/TOP40 (顶尖40)/
JAZZ (爵士乐)/GAME (游戏)
用户设定：调节低音电平、中音电平和高
音电平时显示。
"BASS LEVEL"
(低音电平)
可以对各信号源设定低音电平。
-8 — 0 — +8
"MID LEVEL"
(中音电平)
可以对各信号源设定中音电平。
-8 — 0 — +8
"TRE LEVEL"
(高音电平)
可以对各信号源设定高音电平。
-8 — 0 — +8
"BALANCE"
(平衡)
调节左侧/右侧扬声器的平衡。
(左侧) L15 — 0 — R15 (右侧)
"FADER"
(衰减器)
调节前侧/后侧扬声器的平衡。
(后侧) R15 — 0 — F15 (前侧)
|
中文
51
显示设定
⁄
[SRC] [VOL]
·选择时钟显示时，各信号源的显示设定将变成时钟
显示。
·如果选择的显示项目没有信息，则显示其他信息。
·播放iPod时，如果选择 "FOLDER NAME" (文件夹名
称)，将根据当前选择的浏览项目显示名称。
·播放iPod时，如果iPod手动控制模式接通，则显示
"iPod MODE"。
·使用iPod播放时，如果所有字符无法显示，将显示
列表中的文件号码。
[
]
[VOICE]
信息
显示
显示的选择
音乐名称
文件夹名称
文件名称
"TITLE***"
"FOLDER***"
"FILE***"
变更以下各信号源的显示信息。
1 进入功能设定模式
按下 [VOL] 旋钮1秒钟以上。
显示 "FUNCTION" (功能)。
文本滚动
2 进入显示选择模式
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "DISP SELECT" (显示选择)。
滚动显示的文件名称、歌曲标题等。
按下 [VOICE] 按钮1秒钟以上。
3 选择文本
转动 [VOL] 旋钮，在显示需要的项目时按下。
调谐器信号源
信息
频率
时钟
显示
"FREQUENCY"
"CLOCK"
音频文件/ iPod信号源
信息
显示
音乐标题和演员姓名
专辑和演员姓名
文件夹名称
文件名称
"TITLE/ARTIST"
"ALBUM/ARTIST"
"FOLDER NAME"
"FILE NAME"
"P-TIME"
播放时间和音乐号码
时钟
"CLOCK"
CD信号源
信息
显示
光盘标题
音轨标题
播放时间和音轨号码
时钟
"DISC TITLE"
"TRACK TITLE"
"P-TIME"
"CLOCK"
待机/辅助输入信号源
信息
显示
信号源名称
时钟
"SOURCE NAME"
"CLOCK"
4 退出功能设定模式
按下 [
] 按钮1秒钟以上。
|
52 KDC-U546BT
显示设定
辅助输入显示设定
可以选择以下显示设定项目。
选择切换到辅助输入信号源时的显示。
1 进入功能设定模式
1 选择AUX信号源
按下 [VOL] 按钮1秒钟以上。
显示 "FUNCTION" (功能)。
按下 [SRC] 按钮。
选择 "AUX" (辅助) 显示。
2 选择需要的功能项目
2 进入功能设定模式
转动 [VOL] 旋钮，在显示需要的项目时按下。
按下 [VOL] 旋钮1秒钟以上。
显示 "FUNCTION" (功能)。
选择 "SETTINGS" (设定)
功能项目。
＞
"DISPLAY" (显示)
＞
3 进入辅助输入显示设定模式
功能项目
可选设定/项目
转动 [VOL] 旋钮，在显示需要的项目时按下。
"DIMMER SET"
(调光器设定)
按照周围环境的照明调节显示亮度。
OFF(切断)/ON(接通)
选择 "SETTINGS" (设定)
输入名称设定)。
＞
"AUX NAME SET" (辅助
"TEXT SCROLL"
(文本滚动)
滚动显示的文件名称、歌曲标题等。
选择AUTO可自动滚动显示。
AUTO/MANUAL
显示当前选择的辅助输入显示。
4 选择辅助输入显示
转动 [VOL] 旋钮，在显示需要的项目时按下。
"AUX"/"DVD"/"PORTABLE"/"GAME"/"VIDEO"/"TV"
可以显示手机的连接状态、信号强度以及
电池电量。
"BT DVC STATUS"
(Bluetooth装置状态)
HF-CON: 连接状态。
BATT: 手机电池电量。
SIGNAL: 手机信号强度。
· 如果无法从手机获得信息，则无法显
示数据。
5 退出功能设定模式
按下 [
] 按钮1秒钟以上。
· 由于本机的级数和手机的级数不同，因
此本机上显示的状态可能和手机上显示
的状态不一致。
(出厂设定：加下划线)
3 进行设定
转动 [VOL] 旋钮，在显示需要的项目时按下。
4 退出功能设定模式
按下 [
] 按钮1秒钟以上。
|
中文
53
其他功能
释放按钮
初始设定
[SRC] [VOL]
可以选择以下初始设定项目。
1 选择待机信号源
按下 [SRC] 按钮。
选择 "STANDBY" 显示。
2 进入功能设定模式
按下 [VOL] 按钮1秒钟以上。
显示 "FUNCTION" (功能)。
[
]
3 选择功能项目
时钟调节
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "INITIAL SET" (初始设定) ＞ 功能项目。
1 选择信号源
功能项目
"PRESET TYPE"
(预设类型)
可选设定/项目
TYPE NORMAL (普通型) :
按下 [SRC] 按钮。
2 进入功能设定模式
可以分别在6个波段 (FM1、FM2、
FM3、MW、SW1以及SW2) 对1个预设按
钮指定1个电台，也就是可以合计预设36
个电台 (6个电台×6个波段)。
TYPE MIX (混合型) :
与波段 (FM1、FM2、FM3、MW、
SW1及SW2) 无关，可以对6个预设按钮合
计指定6个电台。可以呼出预设电台而无
需切换波段。
按下 [VOL] 按钮1秒钟以上。
显示 "FUNCTION" (功能)。
3 进入时钟调节模式
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "SETTINGS" (设定) ＞ "CLOCK" (时钟) ＞
"CLOCK ADJUST" (时钟调节)。
小时的显示闪烁。
"KEY BEEP"
(按键提示音)
设定操作核对音 (提示音) 的接通/切断。
OFF(切断)/ON(接通)
4 调节时钟
转动 [VOL] 旋钮调节小时，结束小时的调节时按
下 [VOL] 旋钮。
"TDF ALARM"
(防盗面板提醒音)
切断ACC时发出约30秒钟提醒音，提醒不
要忘记拆下面板。
OFF(切断)/ON(接通)
分钟的显示闪烁。
转动 [VOL] 旋钮调节分钟，结束分钟的调节时按
下 [VOL] 旋钮。
"BUILT-IN AUX"
(内置AUX)
当设定为接通时，可以选择AUX信号源。
ON1: 当切换至AUX信号源时，输出连接在
AUX端子的外部装置的音响。
ON2: 如果选择了AUX信号源，接通电源
时，衰减器功能开启。欣赏外部设备
音响时，顺时针旋转音量旋钮取消
衰减器功能。
5 退出功能设定模式
按下 [
] 按钮1秒钟以上。
OFF: 关闭AUX信号源选择。如果不使用
AUX端子，请设定为关闭。
演示模式设定
接通/关闭演示模式。
"CD READ"
(读取CD)
设定读取CD的方法。
1: 在播放光盘时，自动识别音响文件光盘
和音乐CD。
1 进入功能设定模式
按下 [VOL] 按钮1秒钟以上。
显示 "FUNCTION" (功能)。
2: 作为音乐CD进行强制播放。
"SWITCH PREOUT"
(切换预输出)
在后侧输出 ("REAR") 和重低音扬声器输出
("SUB-W") 之间切换预输出
REAR/SUB-W
2 选择演示模式
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "DEMO MODE" (演示模式)。
"SP SELECT"
(选择扬声器)
设定下列扬声器类型时，细调获得最佳
系统Q值。
SP OFF: 关闭
3 设定演示模式
SP 5/4: 对于5英寸和4英寸扬声器
SP 6*9/6: 对于6英寸和6×9英寸扬声器
SP OEM: 对于OEM扬声器
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "ON" (接通) 或 "OFF" (切断)。
4 退出功能设定模式
按下 [
] 按钮1秒钟以上。
|
54 KDC-U546BT
"F/W UP"
(固件升级)
显示固件版本，升级固件。
MEDIA USB: 选择USB装置。
MEDIA CD: 选择CD。
拆卸面板
本机的面板可以拆下带走，便于防盗。
有关固件的升级方法，请浏览本公司
网站。
拆卸面板
按下释放按钮。
(出厂设定: 加下划线)
重新安装面板
请参照下图重新安装面板。
4 进行设定
转动 [VOL] 旋钮，在显示需要的项目时按下。
5 退出功能设定模式
按下 [
] 按钮1秒钟以上。
¤
·按下释放按钮后，请立即取下面板。如果面板没有
取下，则可能由于震动等落下。
·面板是精密的设备部件，可能由于震动和颠簸而损
坏。
·面板拆下后，应保存在面板盒中。
·不得将面板 (或面板盒) 暴露在直射的阳光下或者放
在温度过高或湿度过高的环境。并且应避免过多的
灰尘和可能溅到水。
本机的复位方法
如果本机无法正常工作，请按下复位按钮。按下复位
按钮后，本机恢复到出厂设定状态。
1 解除面板锁定，将面板拆下。
请参照＜拆卸面板＞(第55页) 。
2 按下复位按钮，然后重新安装面板。
复位按钮
|
中文
55
Bluetooth设置
"BT SP SELECT"
(选择Bluetooth装 克风的扬声器以避免发生啸叫或回音。
可以指定输出话音的扬声器。选择远离麦
[SRC] [VOL]
置扬声器)
SP FRONT: 从前侧左扬声器和前侧右扬声器
输出话音。
SP ALL: 从全部扬声器输出话音。
"CALL BEEP"
(来电哔哔声)
当有来电时可输出哔哔声。
ON: 发出哔哔声。
OFF: 取消哔哔声。
"BT F/W UPDATE" 显示固件版本，升级固件。
ꢁ
[
E
] / [ ]
[
] [
]
(Bluetooth固件
升级)
请参照＜显示固件版本＞(第58页)。
"MIC GAIN"
(麦克风增益)
调节用于通话的内置麦克风灵敏度。调节
通话人的声音。设定为 "+" 提高音量。
-3 — 0 — +3
Bluetooth设置
可以选择以下Bluetooth设置项目。
"NR LEVEL"
(降低噪音等级)
降低周围环境产生的噪音但不改变内置麦克
风音量。语音不清晰时请调节通话人的声
音。设定为 "+" 提高降低噪音的强度。
-3 — 0 — +3
1 进入Bluetooth模式
按下[VOL]旋钮。
显示 "BT MODE" (Bluetooth模式)。
"EC LEVEL"
(回音等级)
调节消除回音的等级。设定为 "+" 提高消除
回音的强度。
-2 — 0 — +2
2 进入功能设定模式
按下 [VOL] 旋钮1秒钟以上。
显示 "FUNCTION" (功能)。
(出厂设定: 加下划线)
3 选择功能项目
4 进行设定
转动 [VOL] 旋钮，在显示需要的项目时按下。
选择 "SETTINGS" (设定) ＞ 功能项目或选择
"SETTINGS" (设定) ＞ "DETAILED SET" (详细设定)
＞ 功能项目。
转动 [VOL] 旋钮，在显示需要的项目时按下。
5 退出功能设定模式
按下 [
] 按钮1秒钟以上。
功能项目
可选设定/项目
"PHONE SELECT"
(选择手机)
选择手机连接。请参照＜选择需要连接的
Bluetooth装置＞(第59页)。
"SMS DOWNLOAD"
(下载短信)
下载短信。请参照＜下载短信＞(第59页)。
"SMS INBOX"
(短信收件箱)
显示接收的短信。
请参照＜SMS (短信服务)＞(第60页)。
"VOICE TAG"
(语音标签)
登录语音识别的语音和在电话簿中选择电
话号码分类的语音。
请参照＜添加语音拨号指令＞(第60页) 和
＜对分类设定语音指令＞(第61页)。
"DETAILED SET"
(详细设定)
移动到详细项目。
"DEVICE REGIST" 登录Bluetooth装置 (配对)。
(登录装置)
请参照＜登录Bluetooth装置＞(第57页)。
"S-DVC SELECT"
(选择特殊装置)
"DEVICE DELETE" 取消Bluetooth装置的登录。
(删除装置)
请参照＜删除登录的Bluetooth装置＞(第
57页)
"PIN CODE EDIT" 设定当使用Bluetooth装置登录本机时需要的
(PIN代码编辑)
PIN代码。请参照＜登录PIN代码＞(第58页)
"AUTO ANSWER"
(自动接听)
本功能在预先设定的时间经过后自动接
听来电。
OFF: 不自动接听电话。
0: 立即自动接听电话。
1 — 8 — 99: 经过1-99秒后自动接听
来电。
|
56 KDC-U546BT
登录Bluetooth装置 (配对)
3 选择装置名称
转动 [VOL] 旋钮，在显示需要的装置名称时按下。
显示 "COMPLETE" 后，登录完成。
为了本机能够使用您的Bluetooth装置 (手机)，需要进行
登录 (配对)。最多可向本机登录5台Bluetooth装置。
4
进行＜从本机侧登录＞的第3步，完成登录 (配对)。
从本机侧登录
取消特殊装置登录模式
1 选择Bluetooth装置登录模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
按下 [VOL] 旋钮1秒钟以上。
⁄
·
如果表中没有装置名称，请选择 "OTHER PHONE"。
选择 "SETTINGS" (设定)
＞
"DETAILED SET" (详细设
定) "DEVICE REGIST" (登录装置)。
＞
2 进入Bluetooth装置登录模式
按下 [VOL] 旋钮。
删除登录的Bluetooth装置
搜索Bluetooth装置。
可以删除注册的Bluetooth装置。
完成搜索后，显示 "FINISHED"。
1 选择Bluetooth装置删除模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
3 选择Bluetooth装置
转动 [VOL] 旋钮，在显示需要的Bluetooth装置名称
时按下。
选择 "SETTINGS" (设定)
＞
"DETAILED SET" (详细设
定) "DEVICE DELETE" (删除装置)。
＞
4 输入PIN代码
2 进入Bluetooth装置删除模式
按下 [VOL] 旋钮。
显示 "(姓名)"。
操作种类
选择号码。
操作
转动 [VOL] 旋钮。
按下 [¢] 按钮。
按下 [4] 按钮。
移动到下一位。
删除最后一位。
3 选择Bluetooth装置
转动 [VOL] 旋钮。
5 传送PIN代码
4 删除选择的Bluetooth装置
按下 [VOL] 旋钮。
显示 "DELETE"。
按下 [VOL] 旋钮。
如果显示 "PAIRING OK" (配对成功)，登录完成。
如果即使PIN代码正确但仍然出现错误消息，请尝
试登录特殊Bluetooth装置。
5 退出功能设定模式
按下 [
] 按钮1秒钟以上。
6 返回至装置列表
按下 [VOL] 旋钮。
⁄
7 退出功能设定模式
·登录的手机删除后，电话簿、通话记录、SMS和语
按下 [
] 按钮1秒钟以上。
音标签也被删除。
⁄
·对于PIN代码，本机可最多输入8位。如果PIN代码无
法通过本机输入，则可以通过Bluetooth装置输入。
·如果已经登录了5台或更多的Bluetooth装置，则无
法登录新的Bluetooth装置。
登录特殊Bluetooth装置
允许登录无法正常登录 (配对) 的特殊装置。
1 选择特殊装置登录模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
第56页)。
选择 "SETTINGS" (设定) ＞ "DETAILED SET" (详细
设定) ＞ "S-DVC SELECT" (选择特殊装置)。
2 进入特殊装置登录模式
按下 [VOL] 旋钮。
显示列表。
|
中文
57
Bluetooth设置
登录PIN代码
下载电话簿
操作Bluetooth装置，设定用于登录本机的PIN代码。
从手机下载电话簿资料，然后才能使用本机的电话
簿。
1 选择PIN代码编辑模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
自动下载
如果手机兼容电话簿同步同能，在连接了Bluetooth
装置后，电话簿将自动下载。
选择 "SETTINGS" (设定) ＞ "DETAILED SET" (详细
设定) ＞ "PIN CODE EDIT" (PIN代码编辑)。
⁄
2 进入PIN代码编辑模式
按下 [VOL] 旋钮。
显示当前的PIN代码设定。
·可能要求进行手机的设定。
·如果在出现完成显示后仍然无法找到电话簿数据，
您的手机可能不兼容自动下载电话簿数据的功能。
对于这种情况，请手动操作下载。
3 输入PIN代码
从手机手动操作下载
操作种类
操作
1 操作手机，结束免提连接。
选择号码。
转动 [VOL] 旋钮。
按下 [¢] 按钮。
按下 [4] 按钮。
移动到下一位。
删除最后一位。
2 操作手机，向本机传送电话簿数据
操作手机，向本机下载电话簿资料。
·在下载时: 显示 "DOWNLOADING"。
·下载结束后: 显示 "COMPLETE"。
4 登录PIN代码
按下 [VOL] 旋钮。
3 操作手机，开始免提连接。
显示 "COMPLETE" 后，登录完成。
⁄
5 退出功能设定模式
·对于每部登录的手机，最多可登录1000个人的电话
号码。
·每个电话号码可以最多登录25位号码、以及最多
50*个表示姓名的字符。(* 50: 字符的数量。根据字
符的类型，可以输入的字符可能较少。)
·请操作手机取消下载电话簿资料。
按下 [
] 按钮1秒钟以上。
⁄
·初始值为 "0000"。
·对于PIN代码可最多指定8位。
显示固件版本
显示本机的固件版本。
1 进入Bluetooth固件升级模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
选择 "SETTINGS" (设定) ＞ "DETAILED SET" (详细
设定) ＞ "BT F/W UPDATE" (Bluetooth固件升级)。
2 进入Bluetooth固件升级模式
按下 [VOL] 旋钮。
显示固件版本。
3 退出功能设定模式
按下 [
] 按钮1秒钟以上。
⁄
·有关固件的升级方法，请浏览本公司网站。
|
58 KDC-U546BT
选择需要连接的Bluetooth装置
下载短信
如果已经登录了两台或更多台Bluetooth装置，需要选
择将要使用的Bluetooth装置。
下载手机接收的短信 (SMS)，由本机阅读。
1 选择下载短信模式
1 选择Bluetooth装置选择模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
选择 "SETTINGS" (设定) ＞ "PHONE SELECT" (选择
手机)。
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
选择 "SETTINGS" (设定) ＞ "SMS DOWNLOAD" (下
载短信)。
2 进入下载短信模式
2 进入Bluetooth装置选择模式
按下 [VOL] 旋钮。
显示 "(姓名)"。
按下 [VOL] 旋钮。
显示 "DOWNLOADING" (下载)。
下载结束后，显示 "COMPLETE" (完成)。
3 选择Bluetooth装置
3 退出功能设定模式
转动 [VOL] 旋钮。
按下 [
] 按钮1秒钟以上。
4 设定Bluetooth装置
⁄
按下 [VOL] 旋钮。
·手机必须能够使用Bluetooth传送SMS。可能要求进
行手机的设定。如果手机不兼容SMS功能，功能控
制模式中的SMS下载项目不显示。
显示‘✱(名称)’或‘-(名称)’。
"✱" : 选择的Bluetooth装置占用。
"-" : 选择的Bluetooth装置待机。
" " (空白): Bluetooth装置的选择取消。
·从手机下载SMS时，手机中未打开的短信将被打开。
5 退出功能设定模式
按下 [
] 按钮1秒钟以上。
⁄
·如果一台手机已经被选择，请解除选择，然后选择
其他手机。
|
中文
59
Bluetooth设置
SMS (短信服务)
添加语音拨号指令
在本接收机显示手机收到的SMS。
显示新收到的短信。
向电话簿添加语音标签用于语音拨号。可以最多登录
35个语音标签。
1 选择电话簿姓名编辑模式
¤
关于如何选择设置项目，请参照＜Bluetooth设置＞
·为了防止发生交通事故，驾驶人员在驾驶车辆时不
(第56页)。
得阅读短信。
选择 "SETTINGS" (设定) ＞ "VOICE TAG" (语音标
签)。
当新收到短信时
显示 "SMS RECEIVED"。
无论进行任何操作，该显示均消失。
2 进入语音标签编辑模式
按下 [VOL] 旋钮。
显示SMS
3 进入电话簿姓名编辑模式
转动 [VOL] 旋钮选择 "PB NAME EDIT" (电话簿姓名
编辑)，然后按下 [VOL] 旋钮。
1 选择短信收件箱模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
4 搜索姓名进行登录
选择 "SETTINGS" (设定) ＞ "SMS INBOX" (短信收
件箱)。
请参照＜拨打电话簿中的号码＞(第48页) 的步骤3，
选择需要登录的姓名。
如果已经对一个姓名登录了语音标签，则在该姓名
前显示 "*"。
2 进入短信收件箱模式
按下 [VOL] 旋钮。
显示短信列表。
5 选择模式
转动 [VOL] 旋钮。
3 选择短信
转动 [VOL] 旋钮。
显示
操作
每次按下 [
] 按钮，即在电话号码或姓名和短信
"PB NAME REG"
"PB NAME CHK"*
"PB NAME DEL"*
"RETURN"
登录语音标签。
播放语音标签。
删除语音标签。
返回至步骤3。
接收日期之间切换。
4 显示文本
按下 [VOL] 旋钮。
转动 [VOL] 旋钮滚动短信。
再次按下 [VOL] 旋钮，返回至短信列表画面。
* 只有当选择已经登录了语音标签的名称时显示。
选择 "PB NAME REG" (登录)
5 退出功能设定模式
6 登录语音标签 (第一次)
按下 [
] 按钮1秒钟以上。
按下 [VOL] 旋钮。
⁄
显示 "ENTER1" (第一次输入)。
听到提示音后，请在两秒钟之内说出语音标签。
·在列表的开头，显示没有打开的短信。其他短信按
照接收的顺序显示。
7 确认语音标签 (第二次)
·手机在没有通过Bluetooth连接时收到的SMS无法显
示。下载SMS。
按下 [VOL] 旋钮。
显示 "ENTER 2" (第2次输入)。
听到提示音后，请在两秒钟之内说出与在步骤5中
说过的语音标签相同的语音标签。
显示 "COMPLETE" (完成)。
·下载SMS时无法显示短信。
·在未阅读的短信前面加星号 (*) 表示。
8 结束登录
按下 [VOL] 旋钮。
返回至步骤3。可以继续登录其他语音标签。
⁄
·如果语音没有被识别，则显示消息。按下 [VOL] 旋
钮可再次尝试语音输入。(第71页)
选择 "PB NAME CHK" (播放)
6 按下 [VOL] 旋钮。
播放登录的语音，返回至步骤3。
|
60 KDC-U546BT
选择 "PB NAME DEL" (删除)
6 删除语音标签
按下 [VOL] 旋钮。
7 转动 [VOL] 旋钮选择 "YES" (是)，然后按下 [VOL]
旋钮。
退出电话簿姓名编辑模式
按下 [
] 按钮1秒钟以上。
⁄
·在进行语音标签登录时不输出音响。
对分类设定语音指令
对语音拨号通话添加电话号码分类 (类型) 语音标签。
1 选择电话号码类型编辑模式
关于如何选择设置项目，请参照＜Bluetooth设置＞
(第56页)。
选择 "SETTINGS" (设定) ＞ "VOICE TAG" (语音标
签)。
2 进入语音标签编辑模式
按下 [VOL] 旋钮。
3 进入电话号码类型编辑模式
转动 [VOL] 旋钮选择 "PN TYPE EDIT" (电话号码类
型编辑)，然后按下 [VOL] 旋钮。
4 选择需要设定的分类 (类型)
转动 [VOL] 旋钮，在显示需要的分类时按下。
"GENERAL"/"HOME"/"OFFICE"/"MOBILE"/"OTHER"
5 选择模式
转动 [VOL] 旋钮。
显示
操作
"PB TYPE REG"
"RETURN"
登录语音标签。
返回至步骤3。
6 完成＜添加语音拨号指令＞(第60页) 中的步骤6至8，
登录分类 (类型)。
7 退出功能设定模式
按下 [
] 按钮1秒钟以上。
⁄
·对全部5项分类设定语音标签。如果没有对全部分
类登录语音标签，可能无法通过语音指令呼出电话
簿。
|
中文
61
遥控器的基本操作
iPod/CD/音频文件信号源
选择音乐 [4]/[¢] 按钮
选择文件夹/光盘 [FM+]/[AM-] 按钮
暂停/播放 [38] 按钮
VOL
SRC
ATT
ENT
进入音乐搜索模式 [5]/[∞] 按钮
ꢂ/P
音乐搜索模式时在文件夹/文件之间移动
[5]/[∞] 按钮
AUD
FM
EXIT
AM
返回至前一个文件夹
[
] 按钮
免提手机控制
0 — 9
拨打电话
进入Bluetooth模式
[
] 按钮
DIRECT/OK
(第45, 47, 49页)
进入拨号方法选择模式 [5]/[∞] 按钮
选择拨号方法 [ENT] 按钮
号码拨号输入
共通控制
音量控制 [VOL] 按钮
信号源选择 [SRC] 按钮
降低音量 [ATT] 按钮
操作种类
操作
输入数字。
[0] － [9] 按钮
输入"+"。
[¢] 按钮
输入"#"。
[FM
[AM
[4] 按钮
+
] 按钮
衰减器功能接通时，"ATT" 指示闪烁。再次按下该按
钮时，恢复到先前的音量。
输入"*"。
-
] 按钮
清除输入的电话号码。
进入音响控制模式 [AUD] 按钮
通话 [OK] 按钮
⁄
·有关音响控制步骤和其他操作等操作方法，请参照
＜音响控制＞(第51页)。
接听电话
接听电话
[
] 按钮
返回至前一个项目
[
] 按钮
在专用通话模式和免提通话模式之间切换
从模式退出 [EXIT] 按钮
选择项目 [5]/[∞] 按钮
确定 [ENT] 按钮
[38] 按钮
通话等候
暂停当前的通话，接听其他来电
[
] 按钮
中断当前的通话，接听其他来电 [SRC] 按钮
调谐器信号源
继续当前的通话 [1] 按钮
波段选择 [FM+]/[AM-] 按钮
电台选择 [4]/[¢] 按钮
呼出预设电台 [1] — [6] 按钮
在通话中
结束通话 [SRC] 按钮
调节话音音量 [VOL] 按钮
|
62 KDC-U546BT
遥控器的准备
沿箭头方向，从遥控器中拉出电池绝缘片。
更换遥控器的电池
请使用市售的纽扣型电池 (CR2025)。
1 将诸如曲别针等尖细物体插入小孔，然后拉出电
池座。
按下
拉出
2 根据电池盒内的标识，按照正确的＋、－极方向
放入电池。
CR2025 (+极面)
¤ 注意
·不要将遥控器放在仪表盘等较热的位置。
·锂电池。
如果电池错误放置，可能发生爆炸。仅限使用
相同或同等类型的电池更换。
·不得将电池组或电池放在阳光下、靠近明火等
过热之处。
·请将电池放在儿童拿不到的地方，并且在使用
之前不要打开原包装。请妥善处理旧电池。万
一误吞了电池，请立即与医生取得联系。
|
中文
63
附录
关于音响文件
能够与本机连接的iPod/iPhone
Made for
·可播放的音响文件
MP3 (.mp3)、WMA (.wma)
·
·
·
·
·
·
iPod nano (1st generation)
iPod nano (3rd generation)
iPod nano (5th generation)
iPod with video
iPod touch (1st generation)
iPod touch (2nd generation)
·
·
iPod nano (2nd generation)
iPod nano (4th generation)
·可播放的光盘媒体
CD-R/RW/ROM
·
iPod classic
·可播放的光盘文件格式
ISO 9660 Level 1/2、Joliet、Romeo、长文件名称。
·可播放的USB装置
USB大容量存储器
Works with
iPhone
·
·
iPhone 3G
·
iPhone 3GS
·可播放的USB装置文件系统
FAT16、FAT32
虽然音响文件采用了上述标准，但是由于不同的媒体
或装置的形式或条件而可能无法播放。
·音响文件的播放顺序
文件夹/文件分层例如下所示，文件按照从①至⑩
的顺序播放。
•
•
请将iPod/iPhone软件升级到最新版本。
<
v
: Folder
文件夹
CD
(ꢂ)
根据连接的iPod机型，可使用的控制类型有所不
同。有关详细内容，请参照 www.kenwood.com/cs/
ce/ipod。
:
音响文件
vꢀ
ꢁ
•
在本使用说明书中出现的词汇 "iPod" 表示通过iPod
连接线*连接的iPod或iPhone。需要使用KCA-iP101
(选购附件)。
ꢃ
vꢆ
vꢇ
ꢅ
* 不兼容KCA-iP500。
vꢄ
ꢈ
关于可使用的iPod或iPhone连接线，请参照以下网
页。
vꢉ
v.
⁄
有关音频文件的在线使用指南可以从 www.kenwood.
com/cs/ce/audiofile/ 网站获得。该在线使用指南提供
了本使用说明书中没有记载的详细信息和注释。请务
必同时阅读在线使用指南。
·如果在连接了iPod后开始播放，则先播放由iPod播放的音
乐。这时将显示 "RESUMING" 而不显示文件夹名称等。变
更浏览项目将显示正确的标题等。
·如果iPod显示 "KENWOOD" 或 "✓"，则无法操作iPod。
关于USB装置
·在本使用说明书中，将闪存存储器和具备USB端子
的数字音响播放器称为 "USB装置"。
·如果本机电源接通，当USB装置与本机连接时可进
行充电。
·USB装置应安装在不影响正常驾驶车辆的位置。
·无法通过USB集线器或多合一读卡器连接USB装
置。
·请对本机使用的音响文件备份。由于USB装置的操
作条件，音响文件可能被删除。
对于任何因删除存储的数据造成的损害，本公司不
承担赔偿责任。
·本机不随机提供USB装置。请在市场上购买USB装
置。
·建议使用CA-U1EX (选购) 连接USB装置。
使用非USB兼容连接线将无法保证正常播放。如果
连接线的总长度超过5m，将发生播放异常。
|
64 KDC-U546BT
关于手机
使用激光的产品标志
本机符合下列Bluetooth规格:
CLASS 1
LASER PRODUCT
版本
配置文件
Bluetooth标准版本 2.0
HFP (免提配置文件)
OPP (对象推送配置文件)
PBAP (电话簿存取配置文件)
SYNC (同步配置文件)
关于已获得兼容性验证的手机，请浏览以下URL:
1类激光产品
⁄
贴附在机架或外盒上的标记，是表示该产品使用了分
类为CLASS1激光的标志，表明本装置利用了最弱级
的激光束，并无向装置外辐射的危险。
·对于支持Bluetooth功能的装置，按照Bluetooth SIG规定的
程序进行鉴定，证明符合Bluetooth标准。但是某些型号的
手机无法与这些装置通讯。
·HFP是用于免提通话的配置文件。
·OPP是用于传输资料的配置文件，诸如在装置之间传输电
话簿等。
本象征标志表示，建伍公司制造的本
产品有利于减少对环境的有害影响。
关于 "KENWOOD Music Editor"
·本机支持电脑应用程序 "KENWOOD Music Editor
Lite ver1.0" (KENWOOD音乐编辑器版本1.0) 或更新
的版本。
·使用由 "KENWOOD Music Editor Lite ver1.0" 添
加了数据库信息的音响文件时，可以通过＜音乐搜
索＞(第43页)，按照标题、歌曲集或演员姓名搜索
文件。
·在本使用说明书中，"Music Editor media" (音乐编
辑器媒体) 指含有由建伍音乐编辑器添加了数据库
信息的音频文件的装置。
·可以通过以下网站获得 "KENWOOD Music Editor Lite
ver1.0"：
·有关 "KENWOOD Music Editor Lite ver1.0" 的详细
内容，请参照上述网站或该应用程序的帮助文件。
·The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
·iTunes is a trademark of Apple Inc.
·iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
·iPhone is a trademark of Apple Inc.
·"Made for iPod" means that an electronic accessory
has been designed to connect specifically to iPod
and has been certified by the developer to meet
Apple performance standards.
·"Works with iPhone" means that an electronic
accessory has been designed to connect specifically
to iPhone and has been certified by the developer to
meet Apple performance standards.
·Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
|
中文
65
附录
功能项目列表
待机
调谐器信号源
第一阶层
第二阶层
第三阶层
页
51
52
"AUDIO CONTROL" (参见CD/音频文件信号源部分)
"DISP SELECT"
"SETTINGS"
第一阶层
"DISP SELECT"
"SETTINGS"
第二阶层
第三阶层
页
52
54
"LOCAL SEEK"
"SEEK MODE"
"AUTO MEMORY"
"MONO SET"
"CLOCK"
"CLOCK"
"DISPLAY"
"CLOCK ADJUST"
"DIMMER SET"
"TEXT SCROLL"
"BT DVC STATUS"
46
53
"CLOCK ADJUST"
54
53
54
"INITIAL SET"
"PRESET TYPE"
"KEY BEEP"
"TDF ALARM"
"BUILT-IN AUX"
"CD READ"
"SWITCH PREOUT"
"SP SELECT"
"F/W UP"
"DISPLAY" (参见待机部分)
"DEMO MODE"
Bluetooth免提模式
54
第一阶层
"DISP SELECT"
"SETTINGS"
第二阶层
第三阶层
页
52
"PHONE SELECT"
"SMS DOWNLOAD"
"SMS INBOX"
"DEMO MODE"
54
"VOICE TAG"
CD/音频文件信号源
"DETAILED SET"
"DEVICE REGIST"
"S-DVC SELECT"
"DEVICE DELETE"
"PIN CODE EDIT"
"AUTO ANSWER"
"BT SP SELECT"
"CALL BEEP"
"BT F/W UPDATE"
"MIC GAIN"
"NR LEVEL"
第一阶层
第二阶层
第三阶层
页
"AUDIO CONTROL"
"SUBWOOFER SET"
"BASS BOOST"
"SYSTEM Q"
"BASS LEVEL"
"MID LEVEL"
"TRE LEVEL"
"BALANCE"
"FADER"
"SUB-W LEVEL"
"DETAILED SET"
56
51
"EC LEVEL"
"CLOCK ADJUST"
"LPF SUBWOOFER"
"SUB-W PHASE"
"SUPREME SET"
"CLOCK"
"DISPLAY" (参见待机部分)
54
53
54
"DEMO MODE"
"VOLUME OFFSET"
"DISP SELECT"
"SETTINGS"
52
54
53
54
AUX信号源
"CLOCK"
"DISPLAY" (参见待机部分)
"CLOCK ADJUST"
第一阶层
第二阶层
第三阶层
页
51
52
53
54
53
54
"AUDIO CONTROL" (参见CD/音频文件信号源部分)
"DISP SELECT"
"SETTINGS"
"DEMO MODE"
"AUX NAME SET"
"CLOCK"
"DISPLAY" (参见待机部分)
USB/iPod信号源
"CLOCK ADJUST"
第一阶层
第二阶层
第三阶层
页
51
52
"AUDIO CONTROL" (参见CD/音频文件信号源部分)
"DISP SELECT"
"DEMO MODE"
"SETTINGS"
"SKIP SEARCH"
"MPLIST DELETE"
"CLOCK"
45
"CLOCK ADJUST"
54
53
54
"DISPLAY" (参见待机部分)
"DEMO MODE"
|
66 KDC-U546BT
附件/安装步骤
· 请正确地将扬声器导线分别连接相应的扬声器端子上。如
果共用负极-导线、或将其与汽车的金属部件连接，可能
造成本机损坏或无法正常工作。
附件
1
2
3
4
· 当系统仅连接两个扬声器时，请将两个扬声器的连接器都仅
连接在前侧输出或后侧输出的其中之一 (不得前后混合)。
例如，如果将左侧扬声器的+连接器与前侧输出端子连
接，则不得将-连接器与后侧输出端子连接。
· 安装结束后，请确认汽车制动灯、转向灯和雨刷等是否正
常动作。
..........1
..........2
..........4
..........4
· 本机安装角度不得大于30度。
· 如果有金属物体靠近Bluetooth天线，接收可能发生中断。
Bluetooth天线装置
安装步骤
为了良好的接收
1. 为了防止短路事故，请拔下点火开关钥匙，拆除
为了保证良好接收，请注意下列事项：
蓄电池负极-端子的连接。
·与手机的通讯视线距离为10m (30英尺) 之内。周围
环境可能会使通讯范围缩小。如果在本机和手机之
间存在障碍物，通讯范围也会缩小。上述最大通讯
距离 (10m) 并非保证值。
2. 正确连接各装置的输入和输出导线。
3. 连接电线束的扬声器导线。
4. 按照以下顺序连接电线束导线：接地导线，蓄电
池导线，点火导线。
·由于附近的广播电台或对讲机的信号过强，将会对
通讯造成干扰。
5. 将电线束接头与本机连接。
6. 将本机安装到汽车上。
7. 重新连接蓄电池的负极-端子。
8. 按下复位按钮。
2警告
如果将点火导线 (红色) 和蓄电池导线 (黄色) 与汽车底盘 (接
地) 连接，将造成短路，甚至可能发生火灾。应务必将这些导
线通过保险丝盒与电源连接。
¤
· 安装本机导线需要一定的技能和经验。为了保证安全，应
请专业人员完成安装和连接导线作业。
· 请以 (-) 接地的12V直流电源向本装置供电。
· 不得将本机安装在暴露于直射阳光、高温或高湿的环境。
并且应避免过多的灰尘和可能溅到水。
· 不得使用自备的螺丝。只能使用随机提供的螺丝。如果使
用不适当的螺丝，将可能损坏本机。
· 如电源没有接通 (显示 "PROTECT" (保护))，则扬声器导线可
能发生了短路、或者与汽车底盘接触，保护功能可能启动。
这时，请检查扬声器导线。
· 如果汽车的点火系统没有ACC位置，请将点火导线连接在
可通过点火钥匙接通/切断的电源上。如果将点火导线与诸
如蓄电池导线等始终提供提供电压的电源连接，蓄电池将
会耗尽。
· 仪表板有盖子时，请务必在安装本机时使得面板的开闭操
作不要碰撞盖子。
· 保险丝烧断时，应首先检查导线等有无短路，然后使用相
同规格的保险丝更换。
· 使用胶带或类似材料绝缘未连接的导线。另外，为了防止
短路事故，请不要拆卸附在未连接的导线和端子上的外
罩。
|
中文
67
将导线与端子连接
USB端子
AUX输入 (立体声)
请使用无阻抗的立体声微型插头导线。
FM/AM天线输入
R
L
前侧输出
保险丝 (10A)
后侧输出/重低音扬声器输出
在后侧输出 ("REAR") 和重低音输出 ("SUB-W") 之间切换前级
输出。请参照＜初始设定＞(第54页) 的 "SWITCH PREOUT"
(切换预输出)。
电线束 (附件1)
白色
向前置左扬声器
向前置右扬声器
向后置左扬声器
向后置右扬声器
白色/黑色
灰色
灰色/黑色
绿色
绿色/黑色
紫色
紫色/黑色
不连接时，请不要使得导线从护套中伸出。
电动天线控制导线 (蓝色)
消音控制导线 (茶色)
根据使用的天线，请与电动天线的控制端子、或薄膜型天线
的增幅放大器电源端子或短棒型天线连接。
ANT. CONT
MUTE
有关建伍牌导航系统的连接，请参照该导航系统的使用说明书。
方向盘遥控导线 (淡蓝色/黄色)
功率控制导线 (蓝色/白色)
如果使用方向盘遥控功能，需要安装对应该汽车的专用遥控
适配器 (没有提供)。
REMOTE CONT
STEERING WHEEL
REMOTE INPUT
使用选购的功率放大器时，与电源控制端子连接。
P.CONT
汽车保险
丝盒
点火开关
钥匙
点火导线 (红色)
ACC
汽车保险丝盒
(主保险丝)
蓄电池导线 (黄色)
接地导线 (黑色) · (至汽车底盘)
蓄电池
+
–
|
68 KDC-U546BT
本机的安装/拆卸方法
非日本制造的汽车
取下硬橡胶框
1 操作拆卸工具的凸耳，拆除上侧的两个锁扣。
按图示要领将框向上抬，再向前拉动。
锁定装置
凸耳
使用螺丝刀等折弯安装套管凸耳
部位，将其固定。
附件2
可拆工具
2 上侧拆除后，拆除下侧的两处位置。
⁄
· 请切实固定本机。如本机安装不牢固，会造成跳音等故
障。
⁄
· 框架可以按照同样方法从下侧开始拆下。
日本制造的汽车
本机的拆卸方法
1 请参照＜取下硬橡胶框＞拆卸硬橡胶框。
1 请参照＜取下硬橡胶框＞拆卸硬橡胶框。
2 使用附件螺丝，将本机上的孔 (一边两处) 对准汽
2 取下面板。
车托架固定。
3 如图所示，将两个拆卸工具深深插入两侧的槽
内。
T
N
4 将拆卸工具向下移动，然后在压向内侧的同时将
T/N
本机拉出到中途。
T
N
附件2
T: 丰田牌汽车
N: 日产牌汽车
8 mm
MAX.
8mm
MAX.
3
4
ø5mm
ø5mm
附件3...日产牌汽车
附件4...丰田牌汽车
¤
· 请注意不要被可拆工具的凸耳碰伤。
5 用手小心托住本机全部拉出，以免掉落。
¤ 注意
请将本机安装在汽车的控制台。
在使用本机中和使用后的片刻，不得触摸本机的金
属部件。诸如散热器和壳体等金属部件较热。
|
中文
69
故障检修
本机的某些功能可能由于对本机的某些设置而无效。
音响文件信号源
? 播放音响文件时发生跳音。
! ·无法设置低重音扬声器。
·无法设定低通滤波器。
·重低音扬声器无输出。
✔ 媒体擦伤或者肮脏。
☞ 参照＜CD的使用＞(第39页) 的清洁CD部分清
洁媒体。
·＜音响控制＞(第51页) 的 "SUBWOOFER SET"
(重低音扬声器设定) 没有设定接通。
✔ 录制条件不良。
☞ 重新录制，或者使用其他媒体。
·前级输出没有设定为重低音扬声器。
☞ ＜初始设定＞(第54页) 的 "SWITCH
PREOUT" (切换前级输出)。
免提通话
? 免提通话音量较低。
! 无法设置重低音扬声器相位。
✔ 免提通话音量的设定较低。
低通滤波器设定为 "THROUGH" (通过)。
☞ ＜音响控制＞(第51页) 的 "LPF SUBWOOFER"
(重低音扬声器低通滤波器)。
☞ 免提通话音量可以单独调整。请在免提通话
时调整。＜Bluetooth设置＞(第56页) 的 "MIC
GAIN" (麦克风增益)、"NR LEVEL" (降低噪音
等级) 或 "EC LEVEL" (回音等级)。
! 本机的 "SONGS" (歌曲) 分类包含的歌曲数量与iPod
? 后侧扬声器无声音。
的 "SONGS" (歌曲) 分类包含的歌曲数量不同。
✔ 正在使用免提通话模式通话。
因为本机不支持播客文件的播放，因此本机不算
入播客文件。
☞ 在免提通话模式时，后侧扬声器无声音。
? 在接收来电时无哔哔声。
✔ 某些型号的手机无法听到哔哔声。
☞ 将＜Bluetooth设置＞(第56页) 的 "CALL BEEP"
(来电哔哔声) 设定接通。
有时似乎是本机故障的现象，其实可能是因微小的误
操作或配线失误造成的。在联系维修之前，请首先按
照下表检查可能发生的问题。
? 语音未被识别。
✔ 车窗打开。
共同
☞ 如果环境噪音过大，语音将无法被正常识
别。关闭车窗降低噪音。
? 不发出操作核对音 (提示音)。
✔ 语音较小。
✔ 使用了预输出插口。
☞ 如果语音过小，则无法被正常识别。请以稍
大的声音对着麦克风自然讲话。
☞ 操作核对音 (提示音) 无法从预输出插口输
出。
✔ 说语音标签的人员不是进行登录的人员。
调谐器音源
☞ 仅能够识别登录语音标签人员的语音。
? 广播的接收质量差。
✔ 没有伸展汽车天线。
☞ 全部伸展天线。
光盘音源
? 不播放指定光盘，而播放其他光盘。
✔ 指定的光盘异常脏污。
☞ 请参照＜CD的使用＞(第39页) 的清洁CD部分
清洁CD。
✔ 光盘划伤严重。
☞ 请使用其他光盘。
|
70 KDC-U546BT
NO MUSIC DATA/ERROR15：
·连接的USB装置中没有可播放的音响
下列信息表示系统的状态。
TOC ERROR：
·光盘盒没有光盘。
·光盘过于脏污。
光盘装入方向不对 (反面)。光盘上擦
伤多。
文件。
·播放的媒体中没有记录本机可以播
放的数据。
USB ERROR：
iPod ERROR：
某些故障可能发生在连接的USB装置方
面。
➪ 拆除USB装置，然后将电源开关重
新接通。如果重复同样的显示，请
使用另外的USB装置。
ERROR 05：
ERROR 77：
无法读取该光盘。
因故不能正常运转。
➪ 按下本机的复位按钮。
如果 "ERROR 77" 代码不消失，请与
当地的服务中心洽谈。
与iPod的连接失败。
➪ 拆除USB装置，然后再次连接。
➪ 请确认iPod的软件是否是最新版
本。
IN (闪烁)：
CD播放部分没有正常运行。
➪ 重新插入CD。如果CD无法弹出、或
者即使正确地重新插入CD也依然闪
烁，请切断电源，与附近的服务中
心洽谈。
USB REMOVE (闪烁)：
对于USB/iPod装置选择了拆除模式。
可以安全地拆除USB/iPod装置。
PROTECT (闪烁)：扬声器导线短路、或与汽车底盘接
触，保护功能动作。
NO NUMBER：
NO DATA：
·来电对方未通报来电显示。
·没有电话号码资料。
➪ 妥善布线或者绝缘扬声器导线，然
后按下复位按钮。如果 "PROTECT"
代码仍不消失时，请与当地的服务
中心洽询。
·没有拨出通话一览。
·没有来电通话一览。
·没有未接听电话一览。
·没有电话簿一览。
NA FILE：
播放的音响文件格式本机无法使用。
播放了防止复制的文件。
COPY PRO：
NO ENTRY：
手机没有登录 (配对)。
READ ERROR： 连接的USB装置文件系统损坏。
➪ 再次向USB装置复制文件和文件
夹。如果仍然显示错误信息，请对
USB装置进行初始化处理或使用其
他USB装置。
HF DISCONCT： 本机无法与手机通讯。
HF ERROR 07： 无法使用记忆体。
➪ 切断电源然后再次接通。如果仍然
出现该消息，请按下控制装置的复
位按钮。
NO DEVICE：
虽然没有连接USB装置，但是选择了
USB装置作为信号源。
HF ERROR 68： 本机无法与手机通讯。
➪ 切断电源然后再次接通。如果仍然
出现该消息，请按下控制装置的复
位按钮。
➪ 将信号源变换成为USB以外的其他
信号源。连接USB装置，然后再次
变换成为USB信号源。
UNKNOWN：
无法检测Bluetooth装置。
N/A DEVICE：
·连接了不兼容的USB装置。
DEVICE FULL： 已经登录了5台Bluetooth装置。无法再
登录Bluetooth装置。
·与iPod的连接失败。
➪ 请检查连接的iPod是否兼容。有关
iPod兼容的详细信息，请参照＜关
于音响文件＞(第64页)。
PIN CODE NG： PIN代码错误。
CONNECT NG： 本机无法与该装置连接。
PAIRING NG：
配对错误。
|
中文
71
故障检修
规格
NO MATCHING： 语音标签错误。由于未登录的语音标
签等原因，语音无法被识别。
调频调谐器部
频率范围
: 87.9 MHz － 107.9 MHz (200 kHz间隔)
: 87.5 MHz － 108.0 MHz (50 kHz间隔)
TOO SOFT：
TOO LOUD：
TOO LONG：
语音过轻，无法被识别。
语音过响，无法被识别。
词句或说话过长，无法被识别。
可用灵敏度 (S/N = 26dB)
: 11.2 dBf (1.0 μV/75 Ω)
静噪灵敏度 (DIN S/N = 46dB)
: 19.2dBf (2.5 μV/75 Ω)
NO PHONEBOOK：数据没有包含在电话簿中。
NO MESSAGE： 收件箱内无短信。
频率响应 (±3 dB)
: 30 Hz － 15 kHz
NO RECORD：
语音标签没有在电话簿登录。
信噪比 (单声道)
: 63 dB
MEMORY FULL： 语音标签的数量达到了可在电话簿中
登录的最大数量。
立体声分隔度 (1 kHz)
: 40 dB
NO ACCES：
混合预设存储功能的步骤预设无法使
用。根据选择的波段，预设内容可能
无法呼出。
AM调谐器部
频率范围
波段1 (MW) : 530 kHz － 1700 kHz (10 kHz间隔)
NO VOICE：
无通话。
: 531 kHz － 1611 kHz (9 kHz间隔)
波段2 (SW1) : 2940 kHz － 7735 kHz (5 kHz间隔)
波段3 (SW2) : 9500 kHz － 10135 kHz / 11580 kHz
－ 18135 kHz (5 kHz步进)
可用灵敏度 (S/N = 20dB)
MW : 31 dBμ (36 μV)
SW : 32 dBμ (40 μV)
CD播放机部
激光二极管
: GaAlAs
数字滤波器 (数/模)
: 8倍取样
数/模转换器
: 24 Bit
心轴速度
: 500 － 200 rpm (CLV)
抖晃度
: 低于测量极限
频率响应 (±1 dB)
: 20 Hz － 20 kHz
总谐波失真 (1 kHz)
: 0.01 %
信噪比 (1 kHz)
: 105 dB
动态范围
: 93 dB
MP3解码
: MPEG-1/2 Audio Layer-3标准
WMA解码
: Windows Media Audio标准
|
72 KDC-U546BT
USB接口
共同
USB标准
工作电压
: USB1.1/ 2.0 (全速)
: 14.4 V (容许范围10.5 － 16V)
文件系统
: FAT16/ 32
最大耗电电流
: 10 A
MP3解码
: MPEG-1/2 Audio Layer-3标准
安装尺寸 (宽 × 高 × 深)
: 182 × 53 × 155 mm
WMA解码
重量
: Windows Media Audio标准
: 1.3 kg
最大供电电流
: 500 mA
Bluetooth部
版本
: 获得认证的Bluetooth版本 2.0
频率范围
: 2.402 － 2.480 GHz
输出功率
: +4dBm (MAX)、0dBm (AVE) Power Class 2
最大通讯范围
: 大约10m (32.8英尺) 视线距离
配置文件
: HFP (免提配置文件)
: HSP (耳机配置文件)
: SPP (串行端口配置文件)
: PBAP (电话话簿存取配置文件)
: OPP (对象推送配置文件)
: SYNC (同步配置文件)
音响部
最大输出功率
: 50 W × 4
全带宽功率 (THD1％以下)
: 22 W × 4
扬声器阻抗
: 4 － 8 Ω
音调
低音 : 100 Hz ±8 dB
中音 : 1 kHz ±8 dB
高音 : 10 kHz ±8 dB
预输出电平/负载 (CD)
: 2000 mV/10 kΩ
预输出阻抗
: ≤ 600 Ω
辅助输入
频率响应 (±3 dB)
: 20 Hz － 20 kHz
最大输入电压
: 1200 mV
输入阻抗
: 10 kΩ
规格可能会变更，恕不另行通知。
|
中文
73
产品中有毒有害物质或元素的名称及含量
有毒有害物质或元素
部件名称
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯 多溴二苯醚
(PBB)
(PBDE)
安装基板
×
○
○
○
○
○
○
○
○
○
○
○
○
○
○
框架
×
○
○
机芯 (硬盘驱动器、DVD、CD等)
其他 (附件)
×
○
○
×
○
○
○：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
该标识中表示的数字为自生产日期开始对环境的保护期限、表示不会因产品中含有的有毒有害
物质或元素的外泄造成环境污染、以及对人体或财产造成严重损害的年数。
该环境保护期限并不是对于性能、功能的保证期限。
表示例
在产品及电池等正常使用结束、进行废弃时，请遵守各地方政府的法律和规定予以处理。
|