Kathrein BAS 60 User Manual

Conversion set for flat antenna BAS 60 / BAS 61  
- Modification instructions -  
The conversion set for BAS 60/BAS 61 enables you to convert your mobile flat  
antenna to a stationary antenna. The use determination (purpose) of your  
antenna will also change. After the rnodification has been effected, the antennas  
are identical with the flat antennas BAS 62 or BAS 63. These are flat antennas for  
stationary use. The instructions for the „Conversion set“ are complemented by the  
12-page brochure „Mounting instructions“ supplied together with the flat antennas  
BAS 62/BAS 63.  
Important notice!  
The rnounting instructions contain important information regarding the stationary  
use, the installation, the mounting site and the safety of your flat antenna. lt is  
absolutely necessary that you pay attention to these instructions.  
Do not separate the modification instructions from the mounting instructions. In  
case you sell the antenna, both instructions should be handed over to the new  
owner.  
Purpose  
The conversion set must only be used for the modi-  
fication of the flat antennas BAS 60 and BAS 61. The  
conversion set changes the flat antenna BAS 60 to a  
BAS 62 and the flat antenna BAS 61 to a BAS 63  
(see opposite illustration). After the modification, the  
mobile antennas BAS 60/BAS 61 are stationary anten-  
nas BAS 62/BAS 63.  
Antenna support  
Mobile antenna  
support  
Scope of the supply  
The conversion set is composed of the preassembled  
antenna support and 4 washers (see illustration oppo-  
site). The modification instructions and the 12-page  
mounting instructions „Flat antennas for stationary use,  
BAS 62 and BAS 63“ are in the scope of supply of the  
conversion set.  
Antenna support  
4 x washer  
These instructions for the conversion of your antenna assume that you have the  
skill and knowledge required for a correct rnodification. lf you do not have the  
needed qualities, ask a specialist to do the job for you.  
Safety instructions  
The modification work on the roof of your caravan, mobile home or truck can  
create problems for your safety and life. Kathrein does not assume any responsi-  
bility for damages to people and goods.  
Park the vehicle in a safe place where you are not exposed to dangers (e.g. from  
motor cars passing by) in order to carry out the conversion work.  
Switch off the ignition and pull the handbrake. Only step on the roof of the vehicle  
after having secured the working place.  
Ladders or other climbing aids must be in perfect condition. Wear non-slip shoes.  
4. Driving without the mounted flat antenna  
lf you wish to drive with your vehicle without the flat  
antenna mounted, but the jointed mast still installed,  
you should protect the antenna as shown in opposite  
illustration.  
Mobile antenna support  
Joint  
• Care for adequate insulation or sealing of the  
antenna plug. Protect the plug from moisture.  
Cable binder  
Cable plug  
• Bend the antenna cable to the form of a loop and  
introduce the end of the cable into the joint of the  
mast until the plug has disappeared in the lower  
part of the joint.  
Then check if the mobile antenna support is well  
fixed. lf necessary, tighten the two socket head  
screws of the bracket.  
Driving direction  
5. Mounting the antenna support  
4 hex. socket head screws  
with washers  
• Place the flat antenna evenly on an appropriate  
support.  
Antenna support  
• Place the washers on the socket head screws and  
screw the antenna support to the back of the flat  
antenna (see opposite illustration). Use for that  
purpose the 4 socket head screws belonging to  
the mobile antenna support.  
• Now screw in with your fingers the 4 socket head  
screws. Pay attention that they are not twisted and  
damage the thread.  
Flat antenna  
• When positioning the antenna support, make sure  
that the socket head screws are positioned exactly  
in the middle of the elongated holes. Then take the  
short shaft of an Allen key in your hand and screw  
the socket head screws tight. See opposite  
illustration.  
The hex. socket head screw  
must be positioned in the  
middle of the elongated  
hole of the antenna support  
• Then tighten the socket head screws with a torque  
spanner. The torque moment is 6.5 Nm. lf no  
torque spanner is available, the following method  
will do: Take the long shaft of the Allen key in your  
hand and tighten the socket head screws giving an  
1/4 to an 1/2 turn.  
Take the short  
shaft of the Allen  
key in your hand  
and screw the  
hex. socket  
screw tight.  
Take the long shaft of the  
Allen key in your hand  
and tighten the socket  
head screws giving an  
1/4 to an 1/2 turn.  
6. Notice regarding the polarisation setting  
The polarisation setting is dependent on the geo-  
graphic reception site. The annexed mounting  
instructions „Flat antennas BAS 62 and BAS 63  
for stationary use“ explain on page 4 how the  
polarisation is set.  
KATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 • Postfach 10 04 44 • D-83004 Rosenheim • Deutschland • Telefon (0 80 31) 18 40 • Fax (0 80 31) 18 43 06  

Ricoh CX1 User Manual
Philips Blu ray Player BDP5600 User Manual
Philips AQ6481 User Manual
Panasonic PV GS90 User Manual
Olympus FL 50R User Manual
Nikon 8x25DCF User Manual
MB QUART FKB116 User Manual
Magic Chef EWWC30MCG User Manual
Lochinvar KNIGHT 51 211 User Manual
Kenwood KDC 132 User Manual