JVC XV BP1 User Manual

BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 1  
Blu-ray Disc Player  
XV-BP1  
For customer use:  
Enter below the Model No. and  
Serial No. which are located on the  
rear of cabinet. Retain this  
information for future reference.  
INSTRUCTIONS  
Model No.  
Serial No.  
LVT2007-001B  
[J]  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 3  
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
9.  
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with  
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade  
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an elec-  
trician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and  
the point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus.  
When a cart is used, use caution when moving the cart/product combination to avoid injury from tip-over.  
13. Unplug this apparatus during lightning storms or when unused for long periods of time.  
14. Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in  
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into  
the apparatus, the product has been exposed to rain or moisture, does not operate normally, or has been  
dropped.  
3
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 4  
Notes on Copyrights  
Licenses  
Java and all Java-based trademarks and logos are  
trademarks or registered trademarks of Sun  
Microsystems, Inc. in the United States and other  
countries.  
Because AACS (Advanced Access Content  
System) is approved as content protection sys-  
tem for BD format, similar to use of CSS (Content  
Scramble System) for DVD format, certain restric-  
tions are imposed on playback, analog signal out-  
put, etc., of AACS protected contents. The opera-  
tion of this product and restrictions on this prod-  
uct may vary depending on your time of purchase  
as those restrictions may be adopted and/or  
changed by AACS after the production of this  
product.  
Manufactured under license from Dolby  
Laboratories. Dolby and the double-D symbol are  
trademarks of Dolby Laboratories.  
Manufactured under license under U.S. Patent #:  
5,451,942; 5,956,674; 5,974,380; 5,978,762;  
6,487,535 & other U.S. and worldwide patents  
issued & pending. DTS is a registered trademark  
and the DTS logos, Symbol, DTS-HD and DTS-HD  
Advanced Digital Out are trademarks of DTS, Inc. ©  
1996-2008 DTS, Inc. All Rights Reserved.  
Furthermore, BD-ROM Mark and BD+ are addi-  
tionally used as content protection systems for  
BD format, which imposes certain restrictions  
including playback restrictions for BD-ROM Mark  
and/or BD+ protected contents. To obtain addi-  
tional information on AACS, BD-ROM Mark, BD+,  
or this product, please contact an authorized  
Customer Service Center.  
HDMI, the HDMI logo and High-Definition  
Multimedia Interface are trademarks or registered  
trademarks of HDMI licensing LLC.  
“BD-LIVE” logo is a trademark of Blu-ray Disc  
Association.  
Many BD-ROM/DVD discs are encoded with copy  
protection. Because of this, you should only con-  
nect your player directly to your TV, not to a VCR.  
Connecting to a VCR results in a distorted picture  
from copy-protected discs.  
“DVD Logo” is a trademark of DVD Format/Logo  
Licensing Corporation.  
“x.v.Color” is a trademark of Sony Corporation.  
“Blu-ray Disc” is a trademark.  
This product incorporates copyright protection  
technology that is protected by U.S. patents and  
other intellectual property rights. Use of this copy-  
right protection technology must be authorized by  
Macrovision, and is intended for home and other  
limited viewing uses only unless otherwise autho-  
rized by Macrovision. Reverse engineering or dis-  
assembly is prohibited.  
“BONUSVIEW” is trademark of Blu-ray Disc  
Association.  
This product is licensed under the AVC patent port-  
folio license and VC-1 patent portfolio license for the  
personal and non-commercial use of a consumer to  
(i) encode video in compliance with the AVC  
Standard and VC-1 Standard (“AVC/VC-1 Video”)  
and/or (ii) decode AVC/VC-1 Video that was encod-  
ed by a consumer engaged in a personal and non-  
commercial activity and/or was obtained from a  
video provider licensed to provide AVC/VC-1 Video.  
No license is granted or shall be implied for any  
other use. Additional information may be obtained  
Under the U.S. Copyright laws and Copyright  
laws of other countries, unauthorized recording,  
use, display, distribution, or revision of television  
programs, videotapes, BD-ROM discs, DVDs,  
CDs and other materials may subject you to civil  
and/or criminal liability.  
“AVCHD” and the “AVCHD” logo are trademarks of  
Panasonic Corporation and Sony Corporation.  
4
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 5  
Contents  
Introduction . . . . . . . . . . . . . . . . . .6-12  
Operations . . . . . . . . . . . . . . . . . .24-32  
General playback features . . . . . . . . . . .24-25  
If a disc menu screen is displayed . . . . . . . .26  
Enlarge the playback image . . . . . . . . . . . . .26  
Time Search . . . . . . . . . . . . . . . . . . . . . . . .26  
Skip Search . . . . . . . . . . . . . . . . . . . . . . . . .26  
Marker Search . . . . . . . . . . . . . . . . . . . . . . .26  
Watching from a different angle . . . . . . . . .26  
Last Scene Memory . . . . . . . . . . . . . . . . . . .26  
Using Color (R, G, B, Y) Buttons . . . . . . . .27  
Screen Saver . . . . . . . . . . . . . . . . . . . . . . .27  
Displaying Disc Information On-Screen . . . .27  
About the  
Symbol Display . . . . . . . . . . . . .6  
Symbols Used in this Manual . . . . . . . . . . . . .6  
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . .6  
Moisture Condensation . . . . . . . . . . . . . . . . .6  
Handling the Unit . . . . . . . . . . . . . . . . . . . . . .6  
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . .7  
Regional Code . . . . . . . . . . . . . . . . . . . . . . .7  
BD-ROM Disc Features . . . . . . . . . . . . . . . . .8  
Compatibility Notes . . . . . . . . . . . . . . . . . . . .9  
Certain System Requirements . . . . . . . . . . . .9  
Resetting the Player . . . . . . . . . . . . . . . . . . .9  
Using a USB Flash Drive . . . . . . . . . . . . . . .10  
Using the Home Menu . . . . . . . . . . . . . . . . .10  
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . .11  
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . .11  
Remote Control . . . . . . . . . . . . . . . . . . . . . .12  
Remote Control Operation . . . . . . . . . . . . . .12  
Enjoying BD-LIVE™ or BONUS VIEW™  
in BD-Video . . . . . . . . . . . . . . . . . . . . . . . .28  
Playing a DVD VR Format Disc . . . . . . . . . .29  
Playing a MPEG4 movie file . . . . . . . . . . . .30  
Playing an Audio CD or MP3/WMA files . . . .31  
Viewing a Photo file . . . . . . . . . . . . . . . . . . .32  
Reference . . . . . . . . . . . . . . . . . . .33-37  
Language Codes . . . . . . . . . . . . . . . . . . . . .33  
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . .33  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .34  
Specifications . . . . . . . . . . . . . . . . . . . . . . .35  
This unit’s Audio Output Specifications . . . . .36  
Open source software notice . . . . . . . . . . . .37  
Installation and Setup . . . . . . . . .13-23  
HDMI connection . . . . . . . . . . . . . . . . . . . .13  
Connections to Your TV . . . . . . . . . . . . . . . .14  
Connecting to an Amplifier . . . . . . . . . . . . . .15  
Internet connection . . . . . . . . . . . . . . . . . . .16  
Resolution Setting . . . . . . . . . . . . . . . . .17-18  
Initial Settings . . . . . . . . . . . . . . . . . . . . . . .19  
- General Operation . . . . . . . . . . . . . . . .19  
- [DISPLAY] Menu . . . . . . . . . . . . . . . . .19  
- [LANGUAGE] Menu . . . . . . . . . . . . . .20  
- [AUDIO] Menu . . . . . . . . . . . . . . . . . .20  
- [LOCK] Menu (Parental Control) . . . . . .21  
- [NETWORK] Menu . . . . . . . . . . . . . . . .22  
- [OTHERS] Menu . . . . . . . . . . . . . . . . .23  
5
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 6  
Introduction  
Cleaning Discs  
Fingerprints and dust on the disc can cause poor  
picture quality and sound distortion. Before playing,  
clean the disc with a clean cloth. Wipe the disc from  
the center out.  
To ensure proper use of this product, please read  
this owner’s manual carefully and retain for future  
reference.  
This manual provides information on the operation  
and maintenance of your player. Should the unit  
require service, contact an authorized service loca-  
tion.  
About the Symbol Display  
Do not use strong solvents such as alcohol, ben-  
zine, thinner, commercially available cleaners, or  
anti-static spray intended for older vinyl records.  
“ may appear on your TV display during opera-  
tion and indicates that the function explained in this  
owner’s manual is not available on that specific  
media.  
Moisture Condensation  
Never operate this product immediately after moving  
it from a cold location to a warm location. Leave it  
for two or three hours without operating it. If you use  
this product in such a situation, it may damage discs  
and internal parts.  
Symbols Used in this Manual  
Note:  
Indicates special notes and operating features.  
Handling the Unit  
When shipping the unit  
Tip:  
Indicates tips and hints for making the task easier.  
Please save the original shipping carton and pack-  
ing materials. If you need to ship the unit, for maxi-  
mum protection, re-pack the unit as it was originally  
packed at the factory.  
A section whose title has one of the following sym-  
bols are applicable only to the disc represented by  
the symbol.  
ALL All discs listed below  
Keeping the exterior surfaces clean  
BD BD-ROM disc  
Do not use volatile liquids such as insecticide  
spray near the unit.  
DVD DVD-Video, DVD R/RW in Video mode or  
VR mode and finalized  
Wiping with strong pressure may damage the  
surface.  
AVCHD DVD R/RW in AVCHD format  
MPEG4 MPEG4 files  
ACD Audio CDs  
Do not leave rubber or plastic products in con-  
tact with the unit for a long period of time.  
MP3 MP3 files  
Cleaning the unit  
WMA WMA files  
To clean the player, use a soft, dry cloth. If the sur-  
faces are extremely dirty, use a soft cloth lightly  
moistened with a mild detergent solution.  
Do not use strong solvents such as alcohol, benzine,  
or thinner, as these might damage the surface of the  
unit.  
PHOTO Photo files  
Notes on Discs  
Handling Discs  
Do not touch the playback side of the disc. Hold the  
disc by the edges so that fingerprints do not get on  
the surface. Never stick paper or tape on the disc.  
Maintaining the Unit  
The unit is a high-tech, precision device. If the opti-  
cal pick-up lens and disc drive parts are dirty or  
worn, the picture quality could be diminished.  
For details, please contact your nearest authorized  
service center.  
Storing Discs  
After playing, store the disc in its case. Do not expose  
the disc to direct sunlight or sources of heat and never  
leave it in a parked car exposed to direct sunlight.  
6
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 7  
• Some AVCHD format discs may not play, depend-  
ing on the recording condition.  
Playable Discs  
• AVCHD format discs need to be finalized.  
• “x.v.Color” offers a wider color range than normal  
DVD camcorder discs.  
Blu-ray Disc  
- Discs such as movies that can be pur-  
chased or rented  
- BD-R/RE discs that contain audio titles,  
MPEG4, MP3, WMA, or Photo files.  
Regional Code  
This unit has a regional code printed on the rear of  
the unit. This unit can play only BD-ROM or DVD  
discs labeled same as the rear of the unit or “ALL”.  
DVD-VIDEO  
Discs such as movies that can be pur-  
chased or rented  
DVD-R  
Notes:  
- Video mode and finalized only  
- Supports the dual layer disc also  
- AVCHD format  
- DVD-R discs that contain audio titles,  
MPEG4, MP3, WMA, or Photo files.  
Depending on the conditions of the recording  
equipment or the CD-R/RW (or DVD R/RW) disc  
itself, some CD-R/RW (or DVD R/RW) discs can-  
not be played on the unit.  
Do not attach any seal or label to either side (the  
labeled side or the recorded side) of a disc.  
DVD-RW  
- VR mode, Video mode and finalized  
only  
- AVCHD format  
- DVD-RW discs that contain audio titles,  
MPEG4, MP3, WMA, or Photo files.  
Do not use irregularly shaped CDs (e.g., heart-  
shaped or octagonal). Doing so may result in  
malfunctions.  
Depending on the recording software & the final-  
ization, some recorded discs (CD-R/RW or  
DVD R/RW) may not be playable.  
DVD+R  
- Finalized disc only  
- Supports the dual layer disc also  
- AVCHD format  
- DVD+R discs that contain audio titles,  
MPEG4, MP3, WMA, or Photo files.  
DVD R/RW and CD-R/RW discs recorded using  
a personal computer or a DVD or CD Recorder  
may not play if the disc is damaged or dirty, or if  
there is dirt or condensation on the player’s lens.  
If you record a disc using a personal computer,  
even if it is recorded in a compatible format, there  
are cases in which it may not play because of the  
settings of the application software used to create  
the disc. (Check with the software publisher for  
more detailed information.)  
DVD+RW  
- Video mode and finalized only  
- AVCHD format  
- DVD+RW discs that contain audio titles,  
MPEG4, MP3, WMA, or Photo files.  
This player requires discs and recordings to meet  
certain technical standards in order to achieve  
optimal playback quality. Pre-recorded DVDs are  
automatically set to these standards. There are  
many different types of recordable disc formats  
(including CD-R containing MP3 or WMA files)  
and these require certain pre-existing conditions  
to ensure compatible playback.  
Audio CD  
Audio CDs or CD-Rs/CD-RWs in audio  
CD format that can be purchased  
CD-R/CD-RW  
CD-R/CD-RW discs that contain audio  
titles, MPEG4, MP3, WMA, or Photo files.  
AVCHD (Advanced Video Codec High Definition)  
• This player can playback AVCHD format discs.  
These discs are normally recorded and used in  
camcorders.  
• The AVCHD format is a high definition digital video  
camera format.  
• The MPEG-4 AVC/H.264 format is capable of  
compressing images at higher efficiency than that  
of the conventional image compressing format.  
• Some AVCHD discs use the “x.v.Color” format.  
• This player can playback AVCHD discs using  
“x.v.Color” format.  
Customers should note that permission is  
required in order to download MP3 / WMA files  
and music from the Internet. Our company has no  
right to grant such permission. Permission should  
always be sought from the copyright owner.  
This player supports 8 cm disc except Blu-ray  
Disc.  
7
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 8  
Menu sounds  
BD-ROM Disc Features  
BD-ROM Discs can store 25 GB (single layer) or  
50 GB (dual layer) on a single sided disc - about  
5 to 10 times the capacity of a DVD.  
When you highlight or select a menu option, sounds  
can be heard such as button clicks or a voice-over  
explaining the highlighted menu choice.  
Multi-page/PopUp Menus  
BD-ROM Discs also support the highest quality HD  
video available in the industry (up to 1920 x 1080) -  
Large capacity means no compromise on video  
quality. Furthermore, a BD-ROM disc has the same  
familiar size and look as DVD.  
With DVD-Video, playback is interrupted each time a  
new menu screen is accessed. Due to BD-ROM  
disc’s ability to preload data from the disc without  
interrupting playback, a menu can consist of several  
pages.  
You can browse through the menu pages or select  
different menu paths, while the audio and video  
remain playing in the background.  
The following BD-ROM disc features are disc  
dependent and will vary.  
Appearance and navigation of features will also  
vary from disc to disc.  
Not all discs will have the features described  
below.  
BD-ROM, Hybrid disc have both BD-ROM and  
DVD (or CD) layers on one side. On such discs,  
BD-ROM layer will be only played back in this  
player.  
Interactivity  
Certain BD-ROM Discs may contain animated  
menus and/or trivia games.  
User Browsable Slideshows  
With BD-ROM Discs, you can browse through vari-  
ous still pictures while the audio remains playing.  
Video highlights  
The BD-ROM format for movie distribution supports  
three highly advanced video codecs, including  
MPEG-2, MPEG4 AVC (H.264), and SMPTE VC1.  
HD video resolutions are also available:  
Subtitles  
Depending on what is contained on the BD-ROM  
disc, you may be able to select different font styles,  
sizes and colors for some subtitles. Subtitles may  
also be animated, scrolled or faded in and out.  
1920 x 1080 HD  
1280 x 720 HD  
BD-J Interactive Capability  
For High-Definition Playback  
The BD-ROM format supports Java for interactive  
functions. “BD-J” offers content providers almost  
unlimited functionality when creating interactive  
BD-ROM titles.  
To view high-definition contents from BD-ROM discs,  
an HDTV is required. Some discs may require HDMI  
OUT for viewing of high-definition contents. Ability to  
view high-definition contents in BD-ROM discs may  
be limited depending on the resolution of your TV.  
BD-ROM Disc Compatibility  
This player supports BD-ROM Profile 2.  
• Discs supporting BD-Live (BD-ROM version 2  
Profile 2) that allows interactive functions to be  
used when this unit is connected to the Internet in  
addition to the BONUSVIEW function.  
• Discs supporting BONUSVIEW (BD-ROM version  
2 Profile 1 version 1.1/Final Standard Profile) that  
allows Virtual packages or Picture-in-Picture func-  
tions to be used.  
Graphic planes  
Two individual, full HD resolution (1920x1080)  
graphic planes (layers) are available, on top of the  
HD video layer. One plane is assigned to video-  
related, frame accurate graphics (like subtitles), and  
the other plane is assigned to interactive graphic  
elements, such as buttons or menus.  
For both planes, various wipes, fades and scroll  
effects may be available.  
• See “Enjoying BD-LIVE™ or BONUS VIEW™ in  
BD-Video” on page 28 for details.  
Graphic  
Plane  
HD Video  
8
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 9  
Compatibility Notes  
Resetting the Player  
If you observe any of the following symptoms...  
When the Player is plugged in, but the power will  
not turn on or off.  
When the display window is not working.  
When the Player does not operate normally.  
Because BD-ROM are a new format, certain disc,  
digital connection and other compatibility issues  
are possible. If you experience compatibility prob-  
lems, please contact an authorized Customer  
Service Center.  
Viewing high-definition content and up-converting  
standard DVD content may require an HDMI-  
capable input or HDCP-capable DVI input on  
your display device.  
You can reset the Player as follows:  
Press and hold the STANDBY/ON button for more  
than five seconds. This will force the Player to  
power off. Press the STANDBY/ON button again  
to turn the Player back on.  
Unplug the power cord and then plug the power  
cord again after more than five seconds.  
Some BD-ROM and DVD discs may restrict the  
use of some operation commands or features.  
Dolby TrueHD, Dolby Digital Plus and DTS-HD  
are supported with maximum 7.1 channels if you  
use HDMI connection for the audio output of the  
unit.  
You can use a USB Flash Drive that is used to  
store some disc related information, including  
downloaded on-line content. The disc you are  
using will control how long this information is  
retained.  
Certain System Requirements  
For high definition video playback:  
High definition display that has COMPONENT or  
HDMI input jacks.  
BD-ROM disc with high definition content.  
HDMI or HDCP capable DVI input on your display  
device is required for some content (as specified  
by disc authors).  
For up-conversion of standard definition DVD, an  
HDMI or HDCP capable DVI input on your display  
device is required for copy protected content.  
For Dolby® Digital Plus, Dolby TrueHD and DTS-HD  
multi-channel audio playback:  
An amplifier/receiver with a built-in (Dolby Digital,  
Dolby Digital Plus, Dolby TrueHD, DTS or  
DTS-HD) decoder.  
Main, center, surround speakers and subwoofer  
as necessary for chosen format.  
9
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 10  
4. Select [USB] then press ENTER.  
Using a USB Flash Drive  
This unit can play the movie, music and photo files con-  
tained on the USB Flash Drive.  
[MOVIE], [MUSIC] or [PHOTO] menu appears.  
Details for the menu are on pages 30-32.  
Using the Home Menu  
From the Home Menu screen you can access all the  
Media for playback and setting of the unit.  
Insert/Remove a USB Flash Drive  
1. Press HOME and the [Home Menu] appears.  
USB Flash Drive  
Inserting a USB Flash Drive  
Insert straight-in until it fits into place.  
Removing a USB Flash Drive  
Withdraw the USB Flash Drive carefully.  
2. Use b / B to select the desired option then  
press ENTER.  
Notes:  
[Movie] – Start video media’s playback or dis-  
plays the [MOVIE] menu.  
This unit supports only USB Flash Drive with  
FAT16 or FAT32 format.  
The USB Flash Drive can be used for the local  
storage for enjoying BD-Live discs with Internet  
Do not extract the USB Flash Drive during opera-  
tion (play, etc.).  
A USB Flash Drive which requires additional pro-  
gram installation when you have connected it to a  
computer is not supported.  
[Photo] – Displays [PHOTO] menu. (page 32)  
[Music] – Displays [MUSIC] menu. (page 31)  
[Setup] – Displays [Setup] menu. (page 19)  
Note:  
When a disc and USB Flash Drive have the con-  
tents, it can choose those menus.  
About Setup menu:  
Menus Buttons Operations  
Moves the cursor.  
USB Flash Drive: USB Flash Drive that support  
USB1.1 and USB2.0.  
Movie Files (MPEG4), Music files (MP3/WMA)  
and photo files (JPEG/PNG/GIF) can be played.  
For details of operations on each file, refer to rel-  
evant pages.  
Regular back up is recommended to prevent data  
loss.  
If you use a Card Reader, USB extension cable  
or USB HUB, the USB Flash Drive may not be  
recognized.  
Some USB Flash Drives may not work with this  
unit.  
Digital camera and mobile phone are not support-  
ed.  
USB Port of the unit cannot be connected to PC.  
The unit cannot be used as a storage device.  
When take off an active device connecting to USB  
port, please take it off after switching off the unit.  
Activates the selected item.  
Closes the menu.  
Tip:  
If you select the [Movie], [Photo] or [Music] option  
when a USB Flash Drive is connected and a disc is  
inserted simultaneously, the menu for selecting a  
media will appear. Select a media then press  
ENTER.  
For example:  
Note:  
The unit will be in stop mode then the [Home Menu]  
will appear if you press HOME during playback.  
Using the USB Flash Drive  
1. Connect a USB Flash Drive.  
2. Press HOME on the Remote Control.  
3. Select [Music], [Photo] or [Movie] option then  
press ENTER.  
10  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 11  
Front Panel  
a
b
c
d
e
f
g
h
i
a 1/' (STANDBY/ON) Button  
f x (STOP)  
Stops playback.  
Switches the unit ON or OFF.  
b Disc Tray  
g N / X (PLAY / PAUSE)  
Insert a disc here.  
Starts playback.  
Pause playback temporarily, press again to exit  
pause mode.  
c Display Window  
Shows the current status of the player.  
h . / > (SKIP)  
d Remote Sensor  
Go to next or previous file/track/chapter.  
Point the Remote Control here.  
i USB Port  
e Z (OPEN/CLOSE)  
Connect a USB Flash Drive.  
Opens or closes the disc tray.  
Rear Panel  
a
b
c
d
e
f
g
h
a AC IN connector  
e LAN port  
Connect the supplied power cord.  
Connect a network with an always-on  
broadband connection.  
b COMPONENT VIDEO OUT (Y Pb Pr)  
Connect to a TV with Y Pb Pr inputs.  
f VIDEO OUT  
Connect to a TV with video inputs.  
c DIGITAL AUDIO OUT (COAXIAL)  
Connect to digital (coaxial) audio equipment.  
g 2CH AUDIO OUT (Left/Right)  
Connect to a TV with 2 channel audio inputs.  
d HDMI OUT (Type A)  
Connect to TV with HDMI inputs. (Interface for  
digital audio and video)  
h DIGITAL AUDIO OUT (OPTICAL)  
Connect to digital (optical) audio equipment.  
11  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 12  
Depending on a disc type or  
DISC MENU: Accesses menu on  
Remote Control  
the pre-recorded contents of  
the BD-ROM disc, different  
functions may be executed  
than other media or there are  
no responses when pressing  
some buttons (depending on  
media used).  
a disc.  
Direction buttons: Select an  
option in the menu.  
ENTER ( ): Acknowledges  
menu selection.  
RETURN (O): Exits or closes  
the menu, or resumes playback.  
The resume play function may  
work depending on the BD-ROM  
disc.  
OPEN/CLOSE (Z): Opens and  
closes the disc tray.  
a
0-9 numerical buttons: Select  
numbered options in a menu.  
DISPLAY: Displays or exits On-  
Screen Display.  
CLEAR: Removes a mark on the  
search menu or a number when  
setting the password.  
AUDIO: Selects an audio lan-  
guage or audio channel.  
JVC TV Control Buttons:  
• TV STANDBY/ON (1/'): Turn  
the TV on or off.  
• INPUT: Switch the TV’s input  
source between the TV and  
other input sources.  
• CH (+/-): Scan up or down  
through memorized channels.  
• VOL (+/-): Adjust the volume of  
the TV.  
SUBTITLE: Selects a  
subtitle language.  
b
c
SUBTITLE ON/OFF: Switches  
the subtitle on or off.  
TITLE/POP-UP: Displays the  
DVD title menu or BD-ROM’s  
popup menu, if available.  
ꢀ ꢀ ꢀ ꢀ d ꢀ ꢀ ꢀ ꢀ  
• MUTING: Temporarily turns TV  
sound OFF, press again to  
restore.  
Color (R, G, B, Y) buttons: Use  
to navigate BD-ROM menus.  
They are also used for [MOVIE],  
[PHOTO] and [MUSIC] menu.  
ꢀ ꢀ ꢀ ꢀ b ꢀ ꢀ ꢀ ꢀ  
MARKER: Marks any point dur-  
m / M (SCAN): Search  
backward or forward.  
ing playback.  
d
SEARCH: Displays or exits the  
. / > (SKIP): Go to next or  
search menu.  
previous chapter / track / file.  
REPEAT: Repeat a desired sec-  
X (PAUSE/STEP): Pauses  
tion.  
playback.  
ꢀ ꢀ ꢀ ꢀ a ꢀ ꢀ ꢀ ꢀ  
ZOOM: Displays or exits the  
[ZOOM] menu.  
N (PLAY): Starts playback.  
STANDBY/ON (1/'): Switches  
the player ON or OFF.  
RESOLUTION: Sets the output  
resolution for HDMI and  
COMPONENT VIDEO OUT  
jacks.  
x (STOP): Stops playback.  
PIP AUDIO Switch on/off  
Secondary Audio (BD-ROM only).  
ꢀ ꢀ ꢀ ꢀ c ꢀ ꢀ ꢀ ꢀ  
PIP : Switches on/off Secondary  
HOME: Displays or exits the  
[Home Menu].  
: This button is not available.  
Video (Picture-in-picture)  
(BD-ROM only).  
Remote Control Battery Installation  
Remote Control Operation  
Point the Remote Control at the remote sensor and  
Remove the battery cover on  
the rear of the Remote Control,  
and insert a R03 (size AAA)  
press the buttons.  
Caution  
battery with  
correctly.  
and  
matched  
• Do not mix old and new batteries and never mix dif-  
ferent types of batteries such as standard, alkaline,  
etc.  
• Do not put the batteries in the place where young  
children can reach.  
12  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 13  
Installation and Setup  
HDMI connection  
HDMI compatible TV  
HDMI  
If you have a HDMI TV or monitor, you can connect  
it to this player using a HDMI cable.  
1. Connect the HDMI jack on the player to the HDMI  
jack on a HDMI compatible TV or monitor (H).  
H
2. Set the TV’s source to HDMI (refer to TV’s  
Owner’s manual).  
Notes:  
You must select a HDMI audio output and a  
maximum sampling frequency that your TV  
accepts using [HDMI] and [Sampling Freq.]  
options on the setup menu (see page 20).  
If a connected HDMI device does not accept the  
audio output of the unit, the HDMI device’s audio  
sound may be distorted or may not output.  
Rear of the player  
Additional Information for HDMI  
Tips:  
When you connect a HDMI or DVI compatible  
device make sure of the following:  
- Try switching off the HDMI/DVI device and this  
player. Next, switch on the HDMI/DVI device  
and leave it for around 30 seconds, then switch  
on this player.  
- The connected device’s video input is set cor-  
rectly for this unit.  
- The connected device is compatible with  
720x480p, 1280x720p, 1920x1080i or  
1920x1080p video input.  
• When you use HDMI connection, you can change  
the resolution for the HDMI output. (Refer to  
“Resolution Setting” on page 17.)  
• Select the type of video output from the HDMI  
OUT jack using [HDMI Color Setting] option on the  
[Setup] menu (see page 19).  
Cautions  
Changing the resolution when the connection has  
already been established may result in malfunc-  
tions. To solve the problem, turn off the player and  
then turn it on again.  
When the HDMI connection with HDCP is not veri-  
fied, TV screen is changed to black screen. In this  
case, check the the HDMI connection, or discon-  
nect the HDMI cable.  
Not all HDCP-compatible HDMI or DVI devices  
will work with this player.  
- The picture will not be displayed properly with  
non-HDCP device.  
- This player does not playback and TV screen is  
changed to black screen.  
If there is noise or lines on the screen, please  
check the HDMI cable (length is generally limited  
to 15ft).  
13  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 14  
Connections to Your TV  
Rear of TV  
Make one of the following connections, depending  
on the capabilities of your existing equipment.  
VIDEO  
INPUT  
AUDIO INPUT  
COMPONENT VIDEO INPUT  
Pr  
R
L
Y
Pb  
Tips  
Depending on your TV and other equipment you  
wish to connect, there are various ways you  
could connect the player. Use only one of the  
connections described below.  
Please refer to the manuals of your TV, Stereo  
System or other devices as necessary to make  
the best connections.  
A
V
C
Caution  
– Make sure the player is connected directly to the  
TV. Tune the TV to the correct video input chan-  
nel.  
– Do not connect the player’s AUDIO OUT jack to  
the phono in jack (record player) of your audio  
system.  
– Do not connect your player via your VCR. The  
image could be distorted by the copy protection  
system.  
Rear of the  
player  
Component Video Connection  
Connect the COMPONENT VIDEO OUT jacks on  
the player to the corresponding input jacks on the  
TV using Y Pb Pr cables (C).  
Tip:  
When you use COMPONENT VIDEO OUT connec-  
tion, you can change the resolution for the output.  
(Refer to “Resolution setting” on page 17.)  
Video Connection  
Connect the VIDEO OUT jack on the player to the  
video in jack on the TV using a video cable (V).  
Audio (Left/Right) Connection  
Connect the left and right AUDIO OUT jacks of the  
player to the audio left and right IN jacks on the TV  
using the audio cables (A).  
14  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 15  
Notes:  
Connecting to an Amplifier  
Make one of the following connections, depending  
on the capabilities of your existing equipment.  
You must select a digital audio output and a max-  
imum sampling frequency that your Amplifier (or  
AV receiver) accepts using [SPDIF], [HDMI] and  
[Sampling Freq.] options on the [Setup] menu  
(see page 20).  
Note:  
Since many factors affect the type of audio output,  
see “The unit’s Audio Output Specifications” on page  
36 for details.  
With digital audio connection (SPDIF or HDMI),  
Disc Menu button sounds of BD-ROM may not be  
heard if the [SPDIF] or [HDMI] option is set to  
[Primary Pass-Thru].  
Connecting to an Amplifier via 2 Channel  
Audio Output  
If the audio format of the digital output does not  
match the capabilities of your receiver, the receiver  
will produce a strong, distorted sound or no sound at  
all.  
Connect the Left and Right 2CH AUDIO OUT jacks  
on the player to the audio left and right in jacks on  
your amplifier, receiver, or stereo system, using  
audio cables (A).  
Multi-channel Digital Surround Sound via digital  
connection can only be obtained if your receiver is  
equipped with a Digital Multi-channel decoder.  
Connecting to an Amplifier via Digital Audio  
Output (Optical or Coaxial)  
To see the audio format of the current disc in the  
on-screen display, press AUDIO.  
1. Connect the player’s DIGITAL AUDIO OUT jack  
to the corresponding in jack (OPTICAL O or  
COAXIAL X) on your amplifier. Use an optional  
digital (optical O or coaxial X) audio cable.  
Rear of the player  
2. You will need to activate the player’s digital out-  
put. (See “[AUDIO] Menu” on pages 20.)  
Connecting to an Amplifier via HDMI Output  
1. Connect the player’s HDMI OUT jack to the cor-  
responding in jack on your amplifier. Use an  
HDMI cable (H1).  
2. You will need to activate the player’s digital out-  
put. (See “[AUDIO] Menu” on pages 20.)  
Tip:  
A
X
O
H1  
Connect the amplifier’s HDMI output jack to HDMI  
input jack on your TV using an HDMI cable (H2) if  
your amplifier has HDMI output jack.  
Digital Multi-channel sound  
HDMI OUTPUT  
A digital multi-channel connection provides the best  
sound quality. For this you need a multi-channel  
Audio/Video Receiver that supports one or more of  
the audio formats supported by your player. Check  
the receiver manual and the logos on the front of the  
receiver. (PCM Stereo, PCM Multi-Ch, Dolby Digital,  
Dolby Digital Plus, Dolby TrueHD, DTS and/or  
DTS-HD)  
L
R
COAXIAL  
DIGITAL INPUT  
OPTICAL  
DIGITAL INPUT  
AUDIO INPUT  
HDMI INPUT  
Amplifier (Receiver)  
H2  
HDMI  
HDMI compatible TV  
15  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 16  
The features of BD-ROM discs made available  
through the Internet Connection feature are not  
created or provided by our company, and our  
company is not responsible for their functionality  
or continued availability. Some disc related mate-  
rial available by the Internet Connection may not  
be compatible with this player. If you have ques-  
tions about such content, please contact the pro-  
ducer of the disc.  
Internet connection  
This player can be connected to a local area net-  
work (LAN) via the LAN port on the rear panel.  
After making the physical connection the player  
needs to be set up for network communication. This  
is done from the [Setup] menu — see “[NETWORK]  
Menu” on page 22 for detailed instructions.  
Connect the player’s LAN port to the corresponding  
port on your Modem or Router using a LAN cable.  
Use a commercially available straight LAN cable  
(Category 5/CAT5 or better with RJ45 connector).  
Some internet contents may require a higher  
bandwidth connection.  
Even if the player is properly connected and con-  
figured, some internet contents may not operate  
properly because of internet congestion, the  
quality or bandwidth of your internet service, or  
problems at the provider of the content.  
Some internet connection operations may not be  
possible due to certain restrictions set by the  
Internet service provider (ISP) supplying your  
broadband Internet connection.  
Any fees charged by an ISP including, without  
limitation, connection charges are your responsi-  
bility.  
A 10 Base-T or 100 Base-TX LAN port is  
required for connection to this player. If your  
internet service does not allow for such a con-  
nection, you will not be able to connect the play-  
er.  
You must use a Router to use xDSL service.  
A DSL modem is required to use DSL service  
and a cable modem is required to use cable  
modem service. Depending on the access  
method of and subscriber agreement with your  
ISP, you may not be able to use the internet con-  
nection feature contained in this player or you  
may be limited to the number of devices you can  
connect at the same time. (If your ISP limits sub-  
scription to one device, this player may not be  
allowed to connect when a PC is already con-  
nected.)  
By connecting the unit to broadband Internet, you  
can use a disc that offers BD-Live function (see  
page 28).  
Cautions:  
When plugging or unplugging the LAN cable, hold  
the plug portion of the cable. When unplugging,  
do not pull on the LAN cable but unplug while  
pressing down on the lock.  
Do not connect a modular phone cable to the  
LAN port.  
Since there are various connection configura-  
tions, please follow the specifications of your  
telecommunication carrier or internet service  
provider.  
Rear of the player  
The use of a “Router” may not be allowed or its  
usage may be limited depending on the policies  
and restrictions of your ISP. For details, contact  
your ISP directly.  
Your ISP may protect this player from being con-  
nected to network when confirming MAC  
ADDRESS. In that case, contact your ISP to  
request to initialize MAC ADDRESS.  
Broadband  
Service  
Router  
Notes:  
Depending on the internet service provider (ISP),  
the number of devices that can receive internet  
service may be limited by the applicable terms of  
service. For details, contact your ISP.  
Our company is not responsible for any malfunc-  
tion of the player and/or the internet connection  
feature due to communication errors/malfunc-  
tions associated with your broadband internet  
connection, or other connected equipment.  
Our company is not responsible for any trouble  
in your internet connection.  
16  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 17  
5. Use v / V to select the desired resolution then  
Resolution Setting  
press ENTER to confirm your selection.  
The player provides several output resolutions for  
HDMI OUT and COMPONENT VIDEO OUT jacks.  
You can change the resolution using [Setup] menu  
or pressing the RESOLUTION button in stop mode.  
Available resolution according to  
connection and media format  
HDMI OUT connection  
Note:  
• If you select a resolution manually and then con-  
nect the HDMI jack to TV and your TV does not  
accept it, the resolution setting is set to [Auto].  
Since several factors affect the resolution of video  
output, see “Video output according to the  
Resolution setting” on next page.  
• If the [1080p Display Mode] option is set to  
[24 Hz], the 1080p video output frame rate may be  
automatically set to either 24Hz or 60Hz depend-  
ing both on the capability and preference of the  
connected TV and based on the native video  
frame rate of the content on the BD-ROM disc.  
Auto – If the HDMI OUT jack is connected for  
TVs providing display information (EDID), auto-  
matically selects the resolution best suited to the  
connected TV. If the COMPONENT VIDEO OUT  
is only connected, this changes the resolution to  
1080i as default resolution.  
COMPONENT VIDEO OUT connection  
1080p – Outputs 1080 lines of progressive  
• For the 720p, 1080i, 1080p resolution setting with  
protected media, real output resolution of COM-  
PONENT VIDEO OUT will be outputted at 480p  
resolution.  
video.  
1080i – Outputs 1080 lines of interlaced video.  
720p – Outputs 720 lines of progressive video.  
480p – Outputs 480 lines progressive video.  
480i – Outputs 480 lines of interlaced video.  
• Even if the resolution is set to 1080p, non-copy  
protected BDs and DVDs playback are outputted  
at 1080i resolution.  
• BD or DVD video stream could prevent up-scaling  
on analog output.  
How to change the resolution using  
RESOLUTION button  
VIDEO OUT connection  
Press RESOLUTION button in stop mode.  
• The resolution of the VIDEO OUT jack is always  
outputted at 480i resolution.  
Notes:  
RESOLUTION button  
• Depending on your display, some of the resolution  
settings may result in the picture disappearing or  
an abnormal picture appearing. In this case, press  
HOME key then RESOLUTION repeatedly until  
the picture re-appear.  
How to change the resolution using  
Setup menu  
• This player supports simultaneous output of all  
video out jacks. The resolution of the HDMI output  
may not be the same as the resolution output on  
the component video output.  
1. Press HOME and the Home Menu appears.  
2. Select [Setup] and press ENTER. The Setup  
menu appears.  
• When the 1080p/24Hz video source is outputted  
via HDMI connection, the VIDEO OUT and COM-  
PONENT VIDEO OUT will not output any video  
signal.  
3. Use v / V to select [DISPLAY] option then press  
B to move to the second level.  
4. Use v / V to select the [Resolution] option then  
press B to move to the third level.  
17  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 18  
Available resolution according to the resolution setting  
• When the non-copy protected media is playing back  
Video Output  
HDMI OUT  
COMPONENT VIDEO OUT  
Resolution Setting  
480i  
480i  
480p  
480i  
480p  
480p  
720p  
720p  
720p  
1080i  
1080i  
1080i  
1080p / 24Hz  
1080p / 60Hz  
1080p / 24Hz  
1080p / 60Hz  
1080i / 60Hz *  
1080i / 60Hz  
• When the copy protected media is playing back  
Video Output  
HDMI OUT  
COMPONENT VIDEO OUT  
Resolution Setting  
480i  
480i  
480p  
480i  
480p  
480p  
480p  
480p*  
480p  
480p  
720p  
720p  
1080i  
1080i  
1080p / 24Hz  
1080p / 60Hz  
1080p / 24Hz  
1080p / 60Hz  
* When the 1080p/24Hz video source is outputted via HDMI connection, the VIDEO OUT and  
COMPONENT VIDEO OUT will not output any video signal.  
18  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 19  
TV Aspect Ratio  
Initial Settings  
[4:3 Letter Box] – Select when a standard 4:3  
TV is connected. Displays theatrical images with  
masking bars above and below the picture.  
By using the Setup menu, you can make various  
adjustments to items such as picture and sound.  
You can also set a language for the subtitles and the  
Setup menu, among other things. For details on  
each Setup menu item, see pages 19 to 23.  
[4:3 Pan Scan] – Select when a standard 4:3 TV  
is connected. Displays pictures cropped to fill your  
TV screen. Both sides of the picture are cut off.  
To display and exit the Menu:  
[16:9 Original] – Select when a 16:9 wide TV is  
connected. The 4:3 picture is displayed with an  
original 4:3 aspect ratio, with black bars appear-  
ing at the left and right sides.  
Press HOME and the Home Menu appears. Select  
[Setup] then press ENTER, and Setup menu  
appears.  
Press RETURN or HOME to exit the Setup menu.  
[16:9 Wide] – Select when a 16:9 wide TV is  
connected. The 4:3 picture is adjusted horizon-  
tally (in a linear proportion) to fill the entire  
screen.  
To go to the next level:  
Press B on the Remote Control.  
To go back to the previous level:  
Press b on the Remote Control.  
Resolution  
Sets the output resolution of the Component and  
HDMI video signal. Refer to “Resolution Setting” on  
page 17 for details about the resolution.  
General Operation  
1. Press HOME and the Home Menu appears.  
2. Select [Setup] and press ENTER. The Setup  
menu appears.  
1080p Display Mode  
When the resolution is set to 1080p, select [24Hz]  
for smooth presentation of film material (1080/24p)  
with an HDMI-equipped display compatible with  
1080/24p input.  
Notes:  
• When you select [24Hz], you may experience  
some picture disturbance when the video switches  
video and film material. In this case, select [60Hz].  
• Even when [1080p Display Mode] is set to [24Hz],  
if your TV is not compatible with 1080/24p, the  
actual frame frequency of the video output will be  
60 Hz.  
• When the 1080p/24Hz video source is outputted  
via HDMI connection, the VIDEO OUT and COM-  
PONENT VIDEO OUT will not output any video  
signal.  
3. Use v / V to select the desired option then press  
B to move to the second level. The screen  
shows the current setting for the selected item,  
as well as alternate setting(s).  
4. Use v / V to select the second desired option  
then press B to move to the third level.  
• If you want to set the 1080p/24Hz, set the resolu-  
tion setting to [1080p] and [1080p Display Mode]  
option to [24Hz].  
5. Use v / V to select the desired setting then  
press ENTER to confirm your selection. Some  
items require additional steps.  
HDMI Color Setting  
6. Press RETURN or HOME to exit the Setup  
menu.  
Select the type of output from the HDMI OUT jack.  
For this setting, please refer to the manuals of your  
display device.  
[DISPLAY] Menu  
[YCbCr] – Select when connecting to an HDMI  
display device.  
[RGB] – Select when connecting to an RGB dis-  
play device.  
Note:  
When you connect the HDMI OUT jack to DVI dis-  
play device, the [HDMI Color Setting] will automati-  
cally switch to [RGB].  
19  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 20  
[PCM Stereo] – Select if you connect this unit’s  
HDMI OUT or DIGITAL AUDIO OUT jack to a  
device with two-channel digital stereo decoder.  
[LANGUAGE] Menu  
[PCM Multi-Ch] (HDMI only) – Select if you  
connect this unit’s HDMI OUT jack to a device  
with multi-channel digital decoder.  
[DTS Re-Encode] – Select if you connect this  
unit’s HDMI OUT or DIGITAL AUDIO OUT jack to  
a device with DTS decoder.  
[Primary Pass-Thru] – Select if you connect this  
unit’s DIGITAL AUDIO OUT and HDMI OUT jack  
to a device with LPCM, Dolby Digital, Dolby  
Digital Plus, Dolby TrueHD, DTS and DTS-HD  
decoder.  
Display Menu  
Select a language for the [Setup] menu and on-  
screen display.  
Disc Menu / Disc Audio / Disc Subtitle  
Notes:  
Select the language you prefer for the audio track  
(disc audio), subtitles, and the disc menu.  
• When [HDMI] option is set to [PCM Multi-CH], the  
audio may output as PCM Stereo if the PCM  
Multi-Ch information is not detected from HDMI  
device with EDID.  
[Original] – Refers to the original language in  
which the disc was recorded.  
[Other] – Press ENTER to select another lan-  
guage. Use number buttons then ENTER to  
enter the corresponding 4-digit number accord-  
ing to the language code list on page 33.  
• If the connected device is only capable of PCM,  
the menu can be changed but it will not affect the  
actual output format.  
[Off] (for Disc Subtitle) – Turn off Subtitle.  
Sampling Freq. (Only for SPDIF audio)  
[192KHz] – Select this if your A/V Receiver or  
Amplifier is capable of handling 192 KHz signals.  
Note:  
Depending upon the disc, your language setting  
may not work for some discs.  
[96KHz] – Select this if your A/V Receiver or  
Amplifier is NOT capable of handling 192 KHz  
signals. When this choice is made, this unit auto-  
matically converts any 192 KHz signals to  
96 KHz so your system can decode them.  
[AUDIO] Menu  
Each disc has a variety of audio output options. Set  
the player’s Audio options according to the type of  
audio system you use.  
[48KHz] – Select this if your A/V Receiver or  
Amplifier is NOT capable of handling 192 KHz  
and 96 KHz signal. When this choice is made,  
this unit automatically converts any 192 KHz and  
96 KHz signals to 48 KHz so your system can  
decode them.  
Note:  
Since many factors affect the type of audio output,  
see “The unit’s Audio Output Specifications” on page  
36 for details.  
Check the documentation for your A/V Receiver or  
Amplifier to verify its capabilities.  
DRC (Dynamic Range Control)  
When a disc encoded in Dolby Digital or Dolby  
Digital Plus is playing back, you may wish to com-  
press the dynamic range of the audio output (the dif-  
ference between the loudest sounds and the qui-  
etest ones). This allows you to listen to a movie at a  
lower volume without losing clarity of sound. Set  
DRC to [On] for this effect.  
HDMI / SPDIF (Digital Audio Output)  
Select the output sound format when a device  
equipped with an HDMI or Digital Audio input jack is  
connected to the HDMI OUT or DIGITAL AUDIO  
OUT jack on this player.  
20  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 21  
[LOCK] Menu (Parental Control)  
Rating  
DVD  
Use the v / V / b / B buttons to select [LOCK] set-  
tings in the [Setup] menu.  
The [LOCK] settings affect only BD and DVD play-  
back. Set the password and have to input it to vali-  
date the [LOCK] settings.  
Blocks playback of rated disc based on their con-  
tent. (Not all discs are rated.)  
1. Select [Rating] on the [LOCK] menu then  
press B.  
2. To access this option, you must input the pass-  
word you have created. If you have not yet  
entered password, you will be prompted to do so.  
Input a password and press ENTER. Enter it  
again and press ENTER to verify. If you make a  
mistake before pressing ENTER, press b to  
delete a number one by one.  
3. Select a rating from 1 to 8 using the v / V but-  
tons.  
Password  
[Rating 1-8] – Rating one (1) has the most  
restrictions and rating eight (8) is the least  
restrictive.  
You can create, change or delete the password.  
1. Select [Password] option on the [LOCK] menu  
[Unlock] – If you select unlock, parental control  
then press B.  
is not active and the disc plays in full.  
2. Use number buttons on the remote control to  
input the 4-digit password.  
4. Press ENTER to confirm your rating selection.  
To create new password, press ENTER when the  
[New] option is highlighted. Input new password  
and press ENTER. Enter it again and press  
ENTER to verify.  
BD Age  
BD  
Set an age limit for BD-ROM viewing.  
1. Select [BD Age] on the [LOCK] menu then  
To change the password, press ENTER when the  
[Change] option is highlighted, then input old  
password and press ENTER. Input new password  
and press ENTER. Enter it again and press  
ENTER to verify.  
press B.  
2. Follow step 2 as shown above (Rating).  
3. Use number buttons to input an age limit for  
BD-ROM viewing.  
To delete the password, select [Delete] option  
then press ENTER, then input old password and  
press ENTER. The password is deleted.  
[255] – All BD-ROM can be played.  
[0-254] – Prohibits play of BD-ROM with corre-  
sponding ratings recorded on them.  
Tip:  
If you make a mistake before pressing ENTER,  
press b to delete a number one by one.  
4. Press ENTER to confirm your selection.  
Area Code  
If you forget your password  
If you forget your password, you can clear it using  
the following steps:  
Enter the code of the area whose standards were  
used to rate the DVD video disc, based on the list  
on page 33.  
1. Remove any disc that might be in the player.  
1. Select [Area Code] on the [LOCK] menu then  
2. Select [LOCK] t [Password] option in the  
press B.  
[Setup] menu.  
2. Follow step 2 as shown above (Rating).  
3. Use Number buttons to enter the 6-digit number  
“210499”.  
3. Select the first character using v / V buttons  
The password is cleared.  
then press ENTER.  
4. Select the second character using v / V buttons  
then press ENTER to confirm your selection.  
21  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 22  
IP Setting  
[NETWORK] Menu  
The [NETWORK] settings are needed to use the  
BD Live features.  
This option is available only if [IP Mode] option is set  
to [Static IP].  
Some BD-ROM discs may enable you to access  
special BD-ROM sites, if you connect the player to  
the Internet. For example, if an BD-ROM site  
includes content such as links to future movie trail-  
ers, you can watch the downloaded on-line content  
on the player.  
Use the v / V / b / B buttons to select a field; use  
the number buttons to enter a value. Press ENTER  
when [OK] is highlighted to finish and exit the  
screen.  
BD-LIVE connection  
You do not need to connect to a PC to use this func-  
tion.  
You can restrict Internet access when BD-Live func-  
tions are used. See “Enjoying BD-LIVE™ or BONUS  
VIEW™ in BD-Video” on page 28 for details.  
Preparations:  
This feature requires an always-on broadband  
internet connection. (see page 16.)  
[Permitted] Internet access is permitted for all  
BD-Live contents.  
An BD-ROM disc compatible with this feature is  
required. Not all BD-ROM discs are compatible.  
[Partially permitted] Internet access is permit-  
ted only for BD-Live contents which have content  
owner certificates. Internet access and AACS  
Online functions are prohibited for all BD-Live  
contents without a certificate.  
[Prohibited] Internet access is prohibited for all  
BD-Live contents.  
When [Prohibited] is selected, the screen may  
become black when BD-Live functions are  
selected. Press STOP to return to Main menu.  
IP Mode  
Notes:  
• Connection confirmation of the Internet is  
displayed when BD-Live mode is started.  
If there is a DHCP server on the local area network  
(LAN), this player will automatically be allocated an  
IP address. If you’re using a broadband router or  
broadband modem that has a DHCP (Dynamic Host  
Configuration Protocol) server function, select  
[Dynamic IP]. The IP address will automatically be  
determined.  
• There are BD-Live data downloaded in USB Flash  
Drive.  
If there is no DHCP server on the network and you  
want to set the IP address manually, select  
[Static IP] then set the [IP Address], [Subnet Mask],  
[Gateway] and [DNS Server] using [IP Setting]  
option.  
How to check the network configuration  
Select [IP Mode] option and check the Network sta-  
tus indicator shown above the menu. (The Network  
status indicator changes according to Network con-  
figuration.)  
Able to use network  
Testing Network  
Unable to use network  
22  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 23  
[OTHERS] Menu  
Skin  
Changes the background of the initial screen.  
Java Font Size BD  
You can adjust the default text size displayed for the  
BD-J contents during BD-ROM playback.  
This setting is only valid when BD-J contents do not  
set the size of text.  
Please select a font size bigger than 24 when the  
player is connected with an HD TV.  
Initialize  
You can reset the player to its original factory set-  
tings or initialize the BD storage.  
1. Select [Initialize] option then press B.  
2. Press v / V to select the desired option then  
press ENTER.  
The confirm message will appear.  
[Factory Set] – If you need to, you can reset the  
player to all its factory settings. Some options  
cannot be reset. (Rating, Password and Area  
Code, etc.)  
[BD Storage Clear] – Deletes the downloaded  
on-line content for BD-Live feature from the con-  
nected USB Flash Drive. The files (such as  
movie, music or photo file) stored in the USB  
Flash Drive except content downloaded via  
BD-Live are not erased.  
3. Use b / B to select [Yes] or [No] then press  
ENTER.  
23  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 24  
Operations  
General playback features  
1. Load your chosen disc in the tray, with the playback side down.  
2. Start playback using the HOME menu (see page 10).  
Buttons  
Operations  
Discs  
ALL  
OPEN / CLOSE (Z) Opens or closes the disc tray.  
ALL  
N (PLAY)  
Starts the playback.  
BD  
DVD  
ENTER  
Acknowledges the selection on the menu screen (Disc  
menu, Title menu, POP-UP menu, etc.).  
ALL  
BD  
x (STOP)  
Stops the playback.  
DVD ACD  
The unit records the stopped point, depending on the  
disc. “Xx” appears on the screen briefly. Press  
N (PLAY) to resume playback (from the scene point). If  
you press x (STOP) again or unload the disc (“x”  
appears on the screen.), the unit will clear the stopped  
point. (Xx = Resume Stop, x = Complete Stop)  
MP3 WMA AVCHD  
MPEG4  
Notes:  
• The resume point may be cleared when a button is  
pressed (for example; STANDBY/ON, OPEN/CLOSE,  
etc).  
• On BD-Video discs including BD-J, the resume play  
function does not work.  
• On BD-ROM interactive title, the unit will be in  
Complete Stop mode if you press x (STOP) once dur-  
ing playback.  
ALL  
X (PAUSE)  
During playback, press X (PAUSE) to pause playback.  
Tip: During Audio CD or MP3/WMA playback, press X  
once again to resume playback.  
DVD  
BD  
AVCHD  
Press X (PAUSE) repeatedly to play Frame-by-Frame.  
MPEG4  
ALL  
. / > (SKIP)  
During playback, press . or > to go to the next  
chapter/track/file or to return to the beginning of the cur-  
rent chapter/track/file.  
Press . twice briefly to step back to the previous  
chapter/track/file.  
ALL  
m / M (SCAN)  
During playback, press SCAN (m or M) repeatedly  
to select the required scan speed.  
- DVD, BD, AVCHD, MPEG4: 5 steps,  
- Audio CD, MP3, WMA: 3 steps  
DVD  
BD  
BD  
AVCHD  
AVCHD  
While the playback is paused, press SCAN M repeat-  
edly to play in slow motion (4 steps, forward only).  
MPEG4  
DVD  
TITLE/POP-UP  
DISC MENU  
If the current DVD or BD-ROM disc has a menu, the Title  
menu or Popup menu appears on the screen. Depending  
on the disc, the menu may not be available.  
The menu appears on the screen. Depending on the  
disc, the menu may not be available.  
DVD  
BD  
AVCHD  
Continued t  
24  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 25  
General disc playback features (Continued)  
Buttons  
Operations  
Discs  
DVD  
REPEAT  
Playing repeatedly:  
During playback, press REPEAT repeatedly to select a  
desired repeat mode.  
DVD, BD, AVCHD: Chapter/Title/Off  
Audio CD, MP3, WMA, MPEG4: Track/All/Off  
BD  
ACD  
MP3 WMA AVCHD  
MPEG4  
Note:  
If you press > once during Repeat Chapter/Track  
playback, the repeat playback cancels.  
Repeating a specific portion (A-B):  
During playback, press REPEAT to select [A-] at the  
beginning of the portion you wish to repeat and press  
ENTER at the end of the portion.  
DVD  
BD  
ACD  
AVCHD MPEG4  
To return to normal playback, press REPEAT repeatedly  
to select [Off].  
Note:  
You cannot select a portion less than 3 seconds.  
SUBTITLE  
During playback, press SUBTITLE repeatedly to select a  
desired subtitle language.  
DVD  
BD  
AVCHD  
MPEG4  
Note:  
Some discs allow you to change subtitle selections only  
via the disc menu. If this is the case, press  
TITLE/POPUP or DISC MENU button and choose the  
appropriate subtitle from the selections on the disc  
menu.  
SUBTITLE ON/OFF During playback, press SUBTITLE ON/OFF to switch  
the subtitle on or off.  
DVD  
MPEG4  
DVD  
BD  
BD  
AVCHD  
AVCHD  
AUDIO  
During playback, press AUDIO repeatedly to hear a dif-  
ferent audio language or audio track.  
MPEG4  
Notes:  
• Some discs allow you to change audio selections only  
via the disc menu. If this is the case, press  
TITLE/POPUP or DISC MENU button and choose the  
appropriate audio from the selections on the disc  
menu.  
• Immediately after you have switched sound, there  
may be a temporary discrepancy between the display  
and actual sound.  
• On BD-ROM disc, the multi audio format (5.1CH or  
7.1CH) is displayed with [MultiCH] in the on-screen  
display.  
Notes on general features:  
When you turn on the player or replace a disc, the player returns to the initial default setting. Depending  
on a disc, a specific type of audio the disc has is output.  
Depending on the pre-recorded contents of the BD-ROM, some functions may not be available or may be  
operated differently than other media.  
25  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 26  
If a disc menu screen is displayed  
Marker Search  
MPEG4  
DVD  
BD  
AVCHD  
MPEG4  
DVD  
BD  
AVCHD  
To enter a Marker  
The menu screen may be displayed first after loading  
a disc which contains a menu.  
You can start playback from up to nine memorized  
points. To enter a marker, press MARKER at the  
desired point on the disc. The Marker icon appears  
on the TV screen briefly. Repeat to enter up to nine  
markers.  
Use b / B / v / V buttons to select the title/chapter  
you want to view, then press ENTER to start play-  
back.  
To Recall or Clear a Marked Scene  
Enlarge the playback image  
1. Press SEARCH and the search menu appears  
on the screen.  
MPEG4  
DVD AVCHD  
2. Press a number button to select a marker num-  
ber that you want to recall. Playback starts from  
the marked scene.  
1. During playback or pause mode, press ZOOM to  
display the [ZOOM] menu.  
2. Use b / B to select zoom mode (16 steps).  
OR  
Press RETURN to exit the [Zoom] menu.  
3. To return to the normal picture size, select [Off]  
on the [ZOOM] menu.  
Press V to highlight a marker number. Use b / B  
to select a marked scene that you want to recall  
or clear.  
Press ENTER and playback starts from the  
marked scene. Press CLEAR and the marked  
scene is erased from the search menu.  
Note:  
This function may not work on some disc or titles.  
Time Search  
MPEG4  
DVD  
BD  
AVCHD  
Notes:  
This function may not work on some disc or  
titles.  
To start playing at any chosen time on the disc:  
1. Press DISPLAY during playback.  
All marked points are cleared if you press  
x (STOP) twice (complete stop), the title is  
changed or unload the disc.  
2. Press v / V to select the time clock icon and  
“--:--:--” appears.  
3. Input the required start time in hours, minutes,  
and seconds from left to right. For example, to  
find a scene at 2 hours, 10 minutes, and  
20 seconds, enter “21020” and press ENTER. If  
you enter the wrong numbers, press CLEAR to  
remove the numbers you entered. Then input the  
correct numbers.  
Watching from a different angle  
BD  
DVD  
If the disc contains scenes recorded at different  
camera angles, you can change to a different cam-  
era angle during playback.  
4. Press ENTER to confirm. Playback starts from  
the selected time.  
1. Press DISPLAY during playback.  
2. Press v / V to select the angle icon then use  
Note:  
b B to select desired angle.  
This function may not work on some disc or titles.  
Last Scene Memory  
DVD  
BD  
Skip Search  
MPEG4  
DVD  
BD  
AVCHD  
This unit memorizes last scene from the last disc  
that is viewed. The last scene remains in memory  
even if you remove the disc from the unit or switch  
off the unit. If you load a disc that has the scene  
memorized, the scene is automatically recalled.  
You can skip the playback 15 seconds forward or  
backward using the search menu.  
1. During playback, press SEARCH and the search  
menu appears on the screen.  
2. Press b / B to skip the playback forward or  
Notes:  
backward.  
Settings are stored in memory for use any time.  
This unit does not memorize settings of a disc if  
you switch off the unit before commencing to  
play it.  
Tip:  
You can select a point that you want to skip by  
pressing and holding b / B button.  
Last Scene Memory function for a previous disc  
is erased once a different disc is played.  
This function may not work depending on the  
disc.  
26  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 27  
Using Color (R, G, B, Y) Buttons  
BD  
These buttons are available only during BD-J  
contents playback. Use the appropriate buttons as  
indicated by the display. Depending on the disc  
contents, the functions of each button may differ.  
Screen Saver  
The screen saver appears when you leave the play-  
er in Stop mode for about five minutes. If the Screen  
Saver is displayed for five minutes, the unit automat-  
ically turns itself off.  
Displaying Disc Information  
On-Screen DVD BD  
MPEG4  
AVCHD  
You can display various information about the disc  
loaded on-screen.  
1. Press DISPLAY to show various playback infor-  
mation.  
The items displayed differ depending on the disc  
type or playing status.  
2. During BD-ROM or DVD playback, you can  
select an item by pressing v / V and change or  
select the setting by pressing b / B.  
Title/Track – Current title/track number/total  
number of titles/tracks.  
Chapter – Current chapter number/total num-  
ber of chapters.  
Time – Elapsed playing time.  
Audio – Selected audio language or channel.  
Subtitle – Selected subtitle.  
Angle – Selected angle/total number of angles.  
Repeat – Selected repeat mode.  
Notes:  
If no button is pressed for a few seconds, the on-  
screen display disappears.  
A title number cannot be selected on some discs.  
An item may not be available on some discs or  
titles.  
If BD interactive title is playing back, some set-  
ting information is displayed on the screen but  
prohibited to be changed.  
27  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 28  
It may take up to several minutes to load and  
start enjoying BD-Live contents.  
Depending on the disc, the BD-Live function  
may not be operated if [BD-LIVE connection]  
option is set to [Partially Permitted]. In this  
case, set [BD-LIVE connection] option to  
[Permitted] (See page 22.)  
The connection to the Internet may take time  
or the Internet may not be connected depend-  
ing on the connection environment. It is  
required that you use a broadband connec-  
tion.  
Do not remove the USB Flash Drive during oper-  
ation. The USB Flash Drive may be damaged.  
Stop playback and turn off the menu beforehand.  
Enjoying BD-LIVE™ or BONUS  
VIEW™ in BD-Video  
BD  
This unit allows you to enjoy functions such as pic-  
ture-in-picture, secondary audio and Virtual pack-  
ages, etc., with BD-Video supporting BONUSVIEW  
(BD-ROM version 2 Profile 1 version 1.1/ Final  
Standard Profile). In addition to the BONUSVIEW  
function, BD-Video supporting BD-Live (BD-ROM  
version 2 Profile 2) that has a network extension  
function allows you to enjoy more functions such as  
online games by connecting this unit to the Internet.  
Enjoying BD-Live discs with Internet  
This unit supports BD-Live, a new BD-Video function  
that allows you to use the following interactive func-  
tions when connected to the Internet. (The usable  
functions and the operating method may vary with  
each disc. For details, refer to the instructions for  
the disc.)  
Tip:  
Special video data, etc. may be played back while  
they are being downloaded to a USB Flash Drive  
using one function of BD-Live. The playback may be  
paused depending on the communication environ-  
ment.  
Additional contents such as movie’s trailer, subti-  
tles and BD-J, etc. can be downloaded to the  
USB Flash Drive to play them.  
Some functions may be disabled to prevent skipping  
to sections that have not been downloaded, etc.  
Special video data, etc. may be played back while  
they are being downloaded to a USB Flash Drive.  
AACS Online  
When discs supporting BD-Live are played back, the  
player or disc IDs may be sent to the content  
provider via the Internet.  
Services and functions to be provided differ depend-  
ing on the disc.  
Preparations:  
• The unit must be connected to the Internet and  
set up to use the BD-Live functions (see page 16  
and 22).  
You can be introduced to other similar movies if  
you record your viewing history on the server by  
using these IDs.  
• A USB Flash Drive is required to use this function.  
Connect a USB Flash Drive (see page 10).  
• The free space in the USB Flash Drive must be  
more than 1GB.  
Game score histories can be saved.  
• Please connect USB Flash Drive before playback  
the Disc.  
Playing secondary video (picture-in-picture)  
and secondary audio  
Caution:  
Secondary video can be played from a disc compati-  
ble with the picture-in-picture function.  
For the playback method, refer to the instructions for  
the disc.  
Do not extract the connected USB Flash Drive  
while content is being downloaded or a Blu-ray  
disc is still in the disc tray. Doing so may dam-  
age the connected USB Flash Drive and BD-Live  
features may not operate properly with the dam-  
aged USB Flash Drive anymore.  
To turn on/off secondary video, press PIP.  
Secondary video is played.  
Press the button to turn it ON or OFF.  
To turn on/off audio with the secondary video,  
press PIP AUDIO. The secondary audio is  
played. Press the button to turn it ON or OFF.  
If the connected USB Flash Drive seems dam-  
aged from such an action, you can format the  
connected USB Flash Drive from the PC and  
reuse it with this player.  
BD-Live on-line contents may not be download-  
ed because of insufficient space in the USB  
Flash Drive. In this case, please change USB  
Flash Drive with sufficient space or erase the  
data using [BD Storage Clear] option on the  
setup menu (See page 23 for details.)  
Notes:  
• Discs may not always be played back according to  
the settings on this unit, as certain playback for-  
mats are prioritized on certain discs.  
• Only the primary video is played during  
search/slow-motion or frame-by-frame.  
• When the secondary video is turned off, the sec-  
ondary audio does not play.  
Notes:  
Some BD-Live contents may be restrictively  
• This function may not work depending on the disc.  
accessed in some territories by contents  
provider's own decision.  
28  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 29  
MOVIE menu options  
Playing a DVD VR Format Disc  
This unit will play DVD-RW disc that is recorded  
using the Video Recording (VR) format.  
1. Use v / V to select a title on the [MOVIE] menu  
then press ENTER.  
The menu options appear.  
1. Insert a disc and close the tray.  
2. Use v / V to select an option, then press  
The [MOVIE] menu appears on the TV screen  
ENTER.  
2. Press v / V to select a title then press  
N (PLAY) and playback starts.  
You can use variable playback functions.  
Refer to pages 24-27.  
3. Press DISC MENU to move to the list menu.  
[Play] Starts playback the selected title.  
Notes:  
[Resume Play] Starts playback from where  
you stopped it previously.  
On the [MOVIE] menu, use red or blue button to  
move to the previous or next page.  
[Close] Exits menu options. Also you can  
Unfinalized DVD-VR format discs may not be  
played in this player.  
disappear it by pressing RETURN button.  
Some DVD-VR disc are made with CPRM data by  
DVD RECORDER. This unit cannot support these  
kinds of discs.  
What is CPRM?  
CPRM is a copy protection system (with scramble  
system) only allowing the recording of ‘copy once’  
broadcast programs. CPRM stands for Content  
Protection for Recordable Media.  
29  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 30  
[Play] Starts playback the selected title.  
Playing a MPEG4 Movie File  
The player can play MPEG4 files. Before playing  
MPEG4 files, read “MPEG4 file requirement” on  
right.  
[Resume Play] Starts playback from where  
you stopped it previously.  
[Close] Exits menu options. Also you can  
disappear it by pressing RETURN button.  
1. Insert a disc containing MPEG4 files, or connect  
the USB Flash Drive containing MPEG4 files.  
Notice for displaying the MPEG4 subtitle  
2. Press HOME and Home Menu appears.  
If the subtitle does not display properly, press and  
hold SUBTITLE for 3 seconds during playback. The  
language code will appear. Press b / B repeatedly  
to select another language code until the subtitle is  
displayed properly and then press ENTER.  
3. Select [Movie] then press ENTER.  
The MOVIE menu appears on the TV screen.  
Note:  
When the USB Flash Drive is connected and a  
disc is inserted simultaneously, the menu for  
selecting a media will appear. Select a media  
then press ENTER.  
MPEG4 file requirement  
MPEG4 file compatibility with this player is limited  
as follows:  
• Available resolution size: 1920 x1080 (W x H)  
pixels  
• The file names of MPEG4 and subtitle are limit-  
ed to 50 characters.  
• MPEG4 file extensions: “.avi”, “.mpg”, “.mpeg”,  
“.mp4”, “.mkv”  
• This unit does not support the DivX file.  
• Playable MPEG4 subtitle: SubRip (.srt / .txt),  
SAMI (.smi), SubStation Alpha (.ssa/.txt),  
MicroDVD (.sub/.txt), SubViewer 2.0 (.sub/.txt),  
TMPlayer (.txt), DVD Subtitle System (.txt)  
2. Press v / V to select a title then press  
N (PLAY) and playback starts.  
You can use variable playback functions.  
Refer to pages 24-27.  
• Playable Codec format: “XVID”, “H.264/MPEG-4  
AVC”  
3. Press DISC MENU to move to the list menu.  
• Playable Audio format: “Dolby Digital”, “DTS”,  
“MP3”, “WMA”, “AAC”  
Note:  
On the [MOVIE] menu, use red or blue colour button  
to move to the previous or next page.  
• Sampling frequency: within 8 - 48 kHz (MP3),  
within 32 - 48 kHz (WMA)  
MOVIE menu options  
• Bit rate: within 8 - 320 kbps (MP3),  
within 32 - 164 kbps (WMA)  
1. Use v / V to select a title on the [MOVIE] menu  
then press ENTER.  
• CD-R/RW, DVD R/RW, BD-R/RE Format:  
ISO 9660+JOLIET, UDF and UDF Bridge format  
The menu options appear.  
• Maximum Files/Folder:  
Less than 650 (total number of files and folders)  
2. Use v / V to select an option, then press  
ENTER.  
• Not all the WMA Audio format is compatible with  
this unit.  
• This player support H.264/MPEG-4 AVC profile  
Main, High at Level 4.1.  
For a file with higher level, the player will ask  
whether you want to play or not.  
• Displaying subtitle file is not available for video  
files with “.mpg” and “.mpeg” extensions.  
• HD movie files contained on the CD or USB  
1.0/1.1 may not played properly. BD, DVD or  
USB 2.0 are recommended to play back HD  
movie files.  
30  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 31  
2. Use v / V to select an option, then press  
Playing an Audio CD or  
ENTER.  
ACD MP3 WMA  
MP3/WMA files  
The player can play Audio CDs and MP3/WMA files.  
Before playing MP3/WMA files, read “MP3/WMA  
audio file requirement” on right.  
1. Insert Audio CD or a disc containing MP3/WMA  
files, or connect the USB Flash Drive containing  
MP3/WMA files  
2. Press HOME and Home Menu appears.  
3. Select [Music] then press ENTER.  
The MUSIC menu appears on the TV screen.  
Note:  
When the USB Flash Drive is connected and a  
disc is inserted simultaneously, the menu for  
selecting a media will appear. Select a media  
then press ENTER.  
[Play] Starts playback the selected track or  
file.  
[Select Play] Plays back only the marked  
track(s) or file(s). Use MARKER for selecting  
the multiple files or tracks.  
All marked tracks or files are cleared if you  
select [Play] option or press PLAY after select-  
ing an unmarked track or file.  
[Random] Starts or stops random playback.  
By pressing > during random playback, the  
unit selects another track and resumes ran-  
dom playback.  
Example) Audio CD  
[Unmark All] Unmarks all marked files or tracks.  
4. Use v/V to select a track or file then press  
N (PLAY). Playback starts.  
[Close] Exits menu options. Also you can dis-  
appear it by pressing RETURN button.  
You can use variable playback functions. Refer  
to pages 24-27.  
Note:  
5. To stop playback at any time, press x (STOP).  
You cannot use [Select Play] and [Random]  
functions simultaneously.  
Tips:  
To go directly to any track or file and play, enter  
the track/file number using the numbered  
buttons (0-9).  
MP3/WMA audio file requirement  
File extensions: “.mp3”, “.wma”  
The playback may start automatically if the  
Audio CD inserted.  
Select a folder then press ENTER and you can  
view the files in the folder. If you want to move to  
the upper directory, use b or v/V to highlight  
Sampling frequency: within 8 - 48 kHz (MP3),  
within 32 - 48kHz (WMA)  
Bit rate: within 8 - 320kbps (MP3),  
within 32 - 164kbps (WMA)  
CD-R/RW, DVD R/RW, BD-R/RE Format:  
ISO 9660+JOLIET, UDF and UDF Bridge format  
and press ENTER.  
[UP Folder]  
On the [MUSIC] menu, use red or blue button to  
move to the previous or next page.  
Maximum Files/Folder:  
Less than 650 (total number of files and folders)  
The equalizer indicator is not coupled with the  
music in play back.  
If there is impossible code to express in the file  
name, it may be displayed as illegible.  
Notes on MP3/WMA file  
• Depending on the size and number of the  
MP3/WMA files, it may take several minutes to  
read the contents of the media.  
• This unit cannot support the ID3 Tag embedded  
in the MP3 file.  
MUSIC menu options  
1. Use v / V to select a track or file on the [MUSIC]  
menu then press ENTER.  
• The total playback time indicated on the screen  
may not correct for VBR files.  
The menu options appear.  
31  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 32  
On the PHOTO menu, use red or blue color but-  
ton to move to the previous or next page.  
PHOTO  
Viewing a Photo file  
If there is impossible code to express in the file  
name, it may be displayed as illegible.  
This unit can play photo files. Before playing photo  
files, read “Photo file requirement” on below.  
Options during viewing a photo file  
in full screen  
You can use various options during viewing a picture in full  
screen. Use v V b B to select an option and use the  
options as described below.  
1. Insert a disc containing photo files, or connect  
the USB Flash Drive containing photo files.  
2. Press HOME and Home Menu appears.  
3. Select [Photo] then press ENTER.  
The PHOTO menu appears on the TV screen.  
a
Note:  
When the USB Flash Drive is connected and a  
disc is inserted simultaneously, the menu for  
selecting a media will appear. Select a media  
then press ENTER.  
b
c
d
e
f
g
a Use b B to advance to the previous or next  
file.  
b Press ENTER to start or pause the slide  
show.  
c Press ENTER to play or pause the back-  
ground music. This option is available after  
the background music is selected using  
[Music Select] option.  
4. Use v V b B to select a file and press ENTER.  
The selected image is displayed in full screen.  
d Press ENTER to rotate the picture clockwise.  
This option is not available during slide show.  
e Press ENTER to set the Slide Show speed.  
f Selects the background music.  
1) Press ENTER and the menu will appear.  
2) Use v V b B to select a media or folder  
that there are music file(s).  
3) Press ENTER to confirm your selection.  
g Press ENTER to exit the option menu.  
5. To stop viewing at any time, press x (STOP).  
To appear the menu again, press ENTER.  
The PHOTO menu appears.  
Tips:  
Photo file requirement  
File extensions: “.jpg”, “.jpeg”, “.png”, “.gif”  
To go directly to any file and play, enter the file  
number using the numbered buttons (0-9).  
You can advance to the previous or next file by  
pressing . or > during viewing a photo file  
in full screen.  
Recommended size:  
Less than 3,000 x 3,000 x 24 bit/pixel  
Less than 3,000 x 2,250 x 32 bit/pixel  
You can start the slide show by pressing  
N (PLAY) while the [PHOTO] menu appears.  
To start the slide show, choose the folder con-  
taining photo files or the photo file then press  
N (PLAY).  
CD-R/RW, DVD R/RW, BD-R/RE Format:  
ISO 9660+JOLIET, UDF and UDF Bridge format  
Maximum Files/Folder:  
Less than 650 (total number of files and folders)  
Notes on Photo file  
Progressive and lossless compression photo  
image files are not supported.  
Depending on the size and number of the photo  
files, it may take several minutes to read the  
contents of the media.  
Select a folder then press ENTER and you can  
view the files in the folder. If you want to move to  
the upper directory, use v/V/b/B to highlight  
and press ENTER.  
[UP Folder]  
32  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 33  
Reference  
Language Codes  
Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and  
[Disc Menu].  
Language  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Ameharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
Bengali; Bangla  
Bhutani  
Bihari  
Breton  
Bulgarian  
Burmese  
Byelorussian  
Cambodian  
Catalan  
Chinese  
Corsican  
Croatian  
Czech  
Code  
6566  
6565  
6570  
8381  
6577  
6582  
7289  
6583  
6589  
6590  
6665  
6985  
6678  
6890  
6672  
6682  
6671  
7789  
6669  
7577  
6765  
9072  
6779  
7282  
6783  
6865  
7876  
6978  
6979  
6984  
7079  
Language  
Fiji  
Finnish  
French  
Frisian  
Galician  
Georgian  
German  
Greek  
Greenlandic  
Guarani  
Gujarati  
Hausa  
Code  
7074  
7073  
7082  
7089  
7176  
7565  
6869  
6976  
7576  
7178  
7185  
7265  
7387  
7273  
7285  
7383  
7378  
7365  
7165  
7384  
7465  
7487  
7578  
7583  
7575  
7589  
7579  
7585  
7679  
7665  
7686  
Language  
Lingala  
Lithuanian  
Macedonian  
Malagasy  
Malay  
Malayalam  
Maltese  
Maori  
Code  
7678  
7684  
7775  
7771  
7783  
7776  
7784  
7773  
7782  
7779  
7778  
7865  
7869  
7879  
7982  
8065  
8083  
7065  
8076  
8084  
8185  
Language  
Singhalese  
Slovak  
Slovenian  
Somali  
Spanish  
Sudanese  
Swahili  
Swedish  
Tagalog  
Tajik  
Code  
8373  
8375  
8376  
8379  
6983  
8385  
8387  
8386  
8476  
8471  
8465  
8484  
8469  
8472  
6679  
8473  
8479  
8482  
8475  
8487  
8575  
8582  
8590  
8673  
8679  
6789  
8779  
8872  
7473  
8979  
9085  
Marathi  
Moldavian  
Mongolian  
Nauru  
Nepali  
Norwegian  
Oriya  
Panjabi  
Pashto, Pushto  
Persian  
Polish  
Portuguese  
Quechua  
Rhaeto-Romance 8277  
Rumanian  
Russian  
Samoan  
Sanskrit  
Scots Gaelic  
Serbian  
Serbo-Croatian  
Shona  
Tamil  
Tatar  
Hebrew  
Hindi  
Telugu  
Thai  
Tibetan  
Tigrinya  
Tonga  
Turkish  
Turkmen  
Twi  
Ukrainian  
Urdu  
Hungarian  
Icelandic  
Indonesian  
Interlingua  
Irish  
Italian  
Japanese  
Javanese  
Kannada  
Kashmiri  
Kazakh  
Kirghiz  
8279  
8285  
8377  
8365  
7168  
8382  
8372  
8378  
8368  
Uzbek  
Vietnamese  
Volapük  
Welsh  
Wolof  
Xhosa  
Yiddish  
Yoruba  
Zulu  
Danish  
Dutch  
English  
Esperanto  
Estonian  
Faroese  
Korean  
Kurdish  
Laothian  
Latin  
Latvian, Lettish  
Sindhi  
Area Codes  
Choose an Area code from this list.  
Area  
Code  
AF  
AR  
AU  
AT  
Area  
Ethiopia  
Fiji  
Finland  
France  
Germany  
Great Britain  
Greece  
Greenland  
Code  
ET  
FJ  
Area  
Code  
MY  
MV  
MX  
MC  
MN  
MA  
NP  
Area  
Saudi Arabia  
Senegal  
Singapore  
Slovak Republic  
Slovenia  
South Africa  
South Korea  
Spain  
Sri Lanka  
Sweden  
Switzerland  
Taiwan  
Thailand  
Turkey  
Code  
SA  
SN  
SG  
SK  
SI  
Afghanistan  
Argentina  
Australia  
Austria  
Belgium  
Bhutan  
Bolivia  
Brazil  
Cambodia  
Canada  
Chile  
China  
Colombia  
Congo  
Costa Rica  
Croatia  
Czech Republic  
Denmark  
Ecuador  
Egypt  
Malaysia  
Maldives  
Mexico  
Monaco  
Mongolia  
Morocco  
Nepal  
Netherlands  
Netherlands Antilles AN  
New Zealand  
Nigeria  
Norway  
FI  
FR  
DE  
GB  
GR  
GL  
BE  
BT  
ZA  
BO  
BR  
KH  
CA  
CL  
CN  
CO  
CG  
CR  
HR  
CZ  
DK  
EC  
EG  
SV  
KR  
ES  
LK  
NL  
Herd and Mcdonald Islands HM  
Hong Kong  
Hungary  
India  
Indonesia  
Israel  
Italy  
Jamaica  
Japan  
Kenya  
Kuwait  
Libya  
Luxembourg  
HK  
HU  
IN  
ID  
IL  
NZ  
NG  
NO  
OM  
PK  
PA  
PY  
PH  
PL  
SE  
CH  
TW  
TH  
TR  
UG  
UA  
US  
UY  
UZ  
VN  
ZW  
Oman  
Pakistan  
Panama  
Paraguay  
Philippines  
Poland  
Portugal  
Romania  
Russian Federation RU  
IT  
Uganda  
Ukraine  
United States  
Uruguay  
Uzbekistan  
Vietnam  
JM  
JP  
KE  
KW  
LY  
LU  
PT  
RO  
El Salvador  
Zimbabwe  
33  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 34  
Troubleshooting  
Possible Cause  
Correction  
Symptom  
No power.  
• The power cord is disconnected.  
• Plug the power cord into the wall out-  
let securely.  
• No disc is inserted.  
• Insert a disc. (Check the disc indica-  
tor in the display window is lit.)  
The power is on, but  
the player does not  
work.  
• The TV is not set to receive video  
signal output.  
• Select the appropriate video input  
mode on the TV.  
No picture.  
No sound.  
• The video cable is not connected  
securely.  
• Connect the video cable securely.  
• The selected resolution is not capa-  
ble with your TV.  
• Select another resolution using  
RESOLUTION button.  
• The equipment connected with the  
audio cable is not set to receive disc  
signal output.  
• Select the correct input mode of the  
audio receiver so you can listen to  
the sound from the player.  
• The power of the equipment connect- • Turn on the equipment connected  
ed with the audio cable is turned off.  
with the audio cable.  
• The [AUDIO] options are set to the  
wrong position.  
• Set the [AUDIO] options to the cor-  
rect position (see page 20).  
• The player is in reverse play, fast for- • Return to the normal playback.  
ward, slow motion or pause mode.  
• The disc is upside down.  
• An unplayable disc is inserted.  
• The rating level is set.  
• Insert the disc with the playback side  
down.  
The player does not  
start playback.  
• Insert a playable disc. (Check the  
disc type and regional code.)  
• Change the rating level.  
• The disc was recorded on another  
unit and was not finalized.  
• Finalize the disc on that unit.  
• A USB Flash Drive is not connected.  
• Connect a FAT16 or FAT32 formatted  
USB Flash Drive to the USB port  
(see page 10).  
BD-Live feature does  
not work.  
• The connected USB Flash Drive  
does not have enough space.  
• Secure at least 1GB free space in  
the USB Flash Drive for using  
BD-Live features  
• Internet connection is not established.  
Ensure that the unit is correctly con-  
nected to the local area network and  
can access the internet (see ) 16).  
Your broadband speed is not fast  
enough to use the BD-Live features.  
• Contact your Internet Service  
Provider (ISP) and increase the  
broadband speed is recommended.  
• The [BD-LIVE connection] option in  
the [Setup] menu is set to  
[Prohibited].  
• Set the [BD-LIVE connection] option  
to [Permitted].  
The Remote Control  
• The Remote Control is not pointed at • Point the Remote Control at the  
the remote sensor on the player.  
remote sensor of the player.  
does not work properly.  
• The Remote Control is too far from  
the player.  
• Operate the Remote Control closer to  
the player.  
• A state is unstable.  
• Unplug the power cord and then plug  
the power cord again after more than  
five seconds.  
The system does not  
function at all.  
34  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 35  
Specifications  
General  
Power requirements:  
Power consumption:  
Dimensions (W x H x D):  
Net Weight (Approx.):  
Operating temperature:  
Operating humidity:  
AC 120 V~, 60 Hz  
18W  
Approx. 16.9 x 2.1 x 9.7 inches (430 x 54 x 245 mm) without foot  
6.2 lbs (2.8 kg)  
41 °F to 95 °F (5 °C to 35 °C)  
5 % to 90 %  
Outputs  
VIDEO OUT:  
1.0 V (p-p), 75 , sync negative, RCA jack x 1  
COMPONENT VIDEO OUT:  
(Y) 1.0 V (p-p), 75 , sync negative, RCA jack x 1  
(Pb)/(Pr) 0.7 V (p-p), 75 , RCA jack x 2  
HDMI OUT (video/audio):  
ANALOG AUDIO OUT:  
19 pin (HDMI standard, Type A)  
2.0 Vrms (1 kHz, 0 dB), 600 , RCA jack (L, R) x 1  
0.5 V (p-p), 75 , RCA jack x 1  
DIGITAL OUT (COAXIAL):  
DIGITAL OUT (OPTICAL):  
3 V (p-p), Optical jack x 1  
System  
Laser:  
Semiconductor laser, wavelength: 405nm / 650 nm  
Standard NTSC Color TV system  
Signal system:  
Frequency response:  
Signal-to-noise ratio:  
Harmonic distortion:  
Dynamic range:  
LAN port:  
20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)  
More than 100 dB (ANALOG OUT connectors only)  
Less than 0.008%  
More than 95 dB  
Ethernet jack x 1, 10BASE-T/100BASE-TX  
Accessories:  
Video cable (1)  
Audio cable (1)  
Remote control (1)  
Batteries (1)  
Note: Design and specifications are subject to change without prior notice.  
35  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 36  
The unit’s Audio Output Specifications  
SPDIF (DIGITAL AUDIO OUT) *5  
Jack/  
Setting  
Analog Output  
Stereo  
PCM  
Stereo  
DTS  
Primary  
Source  
Dolby Digital  
Re-encode *4  
Pass-Thru *1  
Dolby Digital  
Dolby Digital  
Dolby Digital  
DTS  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
DTS  
DTS  
DTS  
DTS  
DTS  
DTS  
DTS  
DTS  
Dolby Digital Plus  
Dolby TrueHD  
DTS  
DTS-HD  
DTS  
Linear PCM 2ch  
Linear PCM 5.1ch  
Linear PCM 7.1ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
Jack/  
Setting  
HDMI OUT  
PCM  
Stereo  
PCM  
Multi-Ch  
DTS  
Primary  
Source  
Dolby Digital  
Re-encode *4  
Pass-Thru *1, *2  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 2ch  
PCM 5.1ch *3  
PCM 7.1ch *3  
PCM 7.1ch *3  
PCM 5.1ch *3  
PCM 5.1ch *3  
PCM 2ch  
DTS  
DTS  
DTS  
DTS  
DTS  
DTS  
DTS  
DTS  
Dolby Digital  
Dolby Digital Plus  
Dolby TrueHD  
DTS  
Dolby Digital Plus  
Dolby TrueHD  
DTS  
DTS-HD  
DTS-HD  
Linear PCM 2ch  
Linear PCM 5.1ch  
Linear PCM 7.1ch  
PCM 2ch  
PCM 5.1ch *3  
PCM 7.1ch *3  
PCM 5.1ch *3  
PCM 7.1ch *3  
Notes:  
*1 The secondary and interactive audio may not be included in the output bitstream if [SPDIF] or [HDMI]  
option is set to [Primary Pass-Thru]. (Except LPCM Codec : the output always include interactive and  
secondary audio.)  
*2 This player automatically selects the HDMI audio according to the decoding capability of the connected  
HDMI device even though [HDMI] option is set to [Primary Pass-Thru].  
*3 On the Multi-Ch PCM audio output, the sampling frequency of HDMI audio output is limited to 96 kHz or  
48 kHz.  
*4 If the [HDMI] or [SPDIF] option is set to [DTS re-encode], the audio output is limited to 48 kHz and 5.1  
Ch.  
• The audio is outputted as PCM 48 kHz/16 bit for MP3/WMA file and PCM 44.1kHz/16 bit for Audio CD  
while playback.  
36  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 37  
Open source software notice  
This product includes  
• Freetype library : copyright © 2003 The FreeType Project (www.freetype.org).  
• Zlib compression library: Copyright © 1995-2002 Jean-loup Gailly and Mark Adler.  
• Expat library : copyright © 2006 expat maintainers.  
• OpenSSL library :  
- cryptographic software written by Eric Young ([email protected]).  
- software written by Tim Hudson ([email protected]).  
- software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org)  
This product includes other open source software.  
• Copyright © 1995, 1996, 1997 Kungliga Tekniska Hogskolan (Royal Institute of Technology, Stockholm,  
Sweden).  
• Copyright © 1995-2008 International Business Machines Corporation and others  
• Copyright © 1999, ASMUS, Inc.  
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associat-  
ed documentation files (the “Software”), to deal in the Software without restriction, including without limita-  
tion the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the  
Software, and to permit persons to whom the Software is furnished to do so, subject to the following condi-  
tions:  
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR  
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS  
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR  
COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN  
AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION  
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.  
• HarfBuzz  
IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE TO ANY PARTY FOR DIRECT, INDIRECT,  
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS SOFT-  
WARE AND ITS DOCUMENTATION, EVEN IF THE COPYRIGHT HOLDER HAS BEEN ADVISED OF  
THE POSSIBILITY OF SUCH DAMAGE.  
THE COPYRIGHT HOLDER SPECIFICALLY DISCLAIMS ANY WARRANTIES, INCLUDING, BUT NOT  
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE. THE SOFTWARE PROVIDED HEREUNDER IS ON AN “AS IS” BASIS, AND THE COPY-  
RIGHT HOLDER HAS NO OBLIGATION TO PROVIDE MAINTENANCE, SUPPORT, UPDATES,  
ENHANCEMENTS, OR MODIFICATIONS.  
37  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 38  
38  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 39  
MEMO  
39  
BD310-JN_BUSAJJK_OM_ENG 2/27/09 4:58 PM Page 40  
EN  
0209SKMLGEEGL  
P/N: MFL62026427  

RCA CC 285 User Manual
Panasonic Car Stereo System DEH 1350MP User Manual
Oregon Scientific Fun Movie Cam AC01 18 User Manual
MTX Audio TA5302 User Manual
Lexar Media DS SDHC 133 381 User Manual
Lanzar Car Audio Lanzar Vibe VIBE251 User Manual
KitchenAid KUWO24LSBX User Manual
Kenwood KFC HQ710 User Manual
Kenwood DPX308U User Manual
JVC GZ HD620U User Manual