DIGITAL VIDEO CAMERA
ENGLISH
CONTENTS
AUTOMATIC DEMONSTRATION
6
GR-DVL120
Please visit our Homepage on the World Wide Web and
answer our Consumer Survey (in English only):
GETTING STARTED
7 – 13
RECORDING & PLAYBACK 14 – 22
RECORDING ................................ 15 – 18
PLAYBACK .................................. 19 – 22
ADVANCED FEATURES
23 – 45
FOR RECORDING .......................... 24 – 31
For Accessories:
USING MENUS FOR
DETAILED ADJUSTMENT ............. 32 – 37
DUBBING .................................... 38 – 39
USING THE OPTIONAL REMOTE
CONTROL UNIT.......................... 40 – 44
SYSTEM CONNECTIONS........................ 45
REFERENCES
46 – Back Cover
DETAILS ............................................ 47
TROUBLESHOOTING ..................... 48 – 52
USER MAINTENANCE ........................... 53
CAUTIONS ................................... 54 – 56
SPECIFICATIONS ................................. 57
INDEX ......................................... 58– 62
TERMS ............................ 63 – Back Cover
For Customer Use:
Enter below the Model No. and Serial
No. which is located on the bottom of the
camcorder. Retain this information for
future reference.
Model No.
Serial No.
INSTRUCTIONS
EN
LYT0944-001A
EN
3
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides
to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
This product has a fluorescent lamp that contains a small amount of mercury. Disposal of these materials
may be regulated in your community due to environmental considerations.
For disposal or recycling information please contact your local authorities, or the Electronics Industries
Alliance:
<http://www.eiae.org>
IMPORTANT PRODUCT SAFETY INSTRUCTIONS
(1) Read these instructions.
(2) Keep these instructions.
(3) Heed all warnings.
(10) Use only with the cart,
stand, tripod, bracket, or
table specified by the
manufacturer, or sold
with the apparatus. When
a cart is used, use
(4) Follow all instructions.
(5) Do not use this apparatus near water.
(6) Clean only with dry cloth.
caution when moving the
cart/apparatus
combination to avoid
injury from tip-over.
(7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
(11) Unplug this apparatus during lightning storms or
(8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
when unused for long periods of time.
(12) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has been
dropped.
apparatus (including amplifiers) that produce heat.
(9) Only use attachments/accessories specified by
the manufacturer.
4
EN
SAFETY PRECAUTIONS
Do not point the lens or the viewfinder directly into the sun. This can cause eye injuries, as well as lead to
the malfunctioning of internal circuitry. There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical damage to the camcorder and to the user.
When carrying, be sure to always securely attach and use the provided shoulder strap. Carrying or
holding the camcorder by the viewfinder and/or the LCD monitor can result in dropping the unit, or in a
malfunction.
Take care not to get your finger caught in the cassette holder cover. Do not let children operate the
camcorder, as they are particularly susceptible to this type of injury.
Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the
camcorder.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving the unit on top of the TV is
not recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.
Ⅲ This camcorder is designed exclusively for the digital video cassette. Only cassettes marked
“
” can be used with this unit.
Before recording an important scene . . .
.... make sure you only use cassettes with the Mini DV mark
.
.... remember that this camcorder is not compatible with other digital video formats.
.... remember that this camcorder is intended for private consumer use only. Any commercial use without
proper permission is prohibited. (Even if you record an event such as a show, performance or
exhibition for personal enjoyment, it is strongly recommended that you obtain permission
beforehand.)
EN
5
PROVIDED ACCESSORIES
AC Adapter AP-V10U,
AP-V11U or AP-V12U
Battery Pack
BN-V408U
Lens Cap
(੬ pg. 6 for
attachment)
Shoulder Strap
Audio/Video Cable
(ø3.5 mini-plug to RCA plug)
NOTE:
In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or more
core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to the camcorder.
6
EN
AUTOMATIC DEMONSTRATION
Automatic Demonstration takes place when “DEMO
MENU/BRIGHT Wheel
MODE” is set to “ON” (factory-preset).
Ⅲ Automatic Demonstration starts when there is no operation for
about 3 minutes after the Power Switch is set to “ ” or “
”
and no cassette is in the camcorder.
Ⅲ Performing any operation during the demonstration stops the
demonstration temporarily. If no operation is performed for more
than 3 minutes after that, the demonstration will resume.
Ⅲ “DEMO MODE” remains “ON” even if the camcorder power is
turned off.
Ⅲ To cancel Automatic Demonstration:
1. Set the Power Switch to “ ” while pressing down the Lock
Button located on the switch and press the MENU/BRIGHT
wheel in. The Menu Screen appears.
Lock Button
Power Switch
Sub Menu
2. Rotate the MENU/BRIGHT wheel to select “
SYSTEM”
and press it. The SYSTEM Menu appears.
3. Rotate the MENU/BRIGHT wheel to select “DEMO MODE”
DEMO MODE
–
OFF
ON
and press it. The Sub Menu appears.
4. Rotate the MENU/BRIGHT wheel to select “OFF” and press
it.
5. Rotate the MENU/BRIGHT wheel to select “
RETURN”,
and press it twice. The normal screen appears.
NOTE:
If you do not detach the Lens Cap, you cannot see the actual changes of the Automatic Demonstration activated on
the LCD monitor or viewfinder.
How To Attach The Lens Cap
To protect the lens, attach the provided lens cap to the camcorder as shown in the illustration.
NOTE:
To confirm the lens cap is on correctly make sure the cap is flush to the camera.
1
2
3
EN
7
GETTING STARTED
GETTING STARTED
CONTENTS
Power.................................................. 8 – 9
Grip Adjustment ......................................... 10
Viewfinder Adjustment.................................. 10
Shoulder Strap Attachment ............................. 10
Tripod Mounting.......................................... 10
Date/Time Settings...................................... 11
Loading/Unloading A Cassette ......................... 12
Recording Mode Setting ................................. 13
8
EN
GETTING STARTED (cont.)
BAT. RELEASE Button
Power
This camcorder’s 2-way power supply system lets
you choose the most appropriate source of power. Do
not use provided power supply units with other
equipment.
1
CHARGING THE BATTERY PACK
3
2
1
Tilt the viewfinder upward 1. With the arrow on
the battery pack pointing downward, push the battery
pack slightly against the battery pack mount 2, then
slide down the battery pack until it locks in place 3.
Power Switch
2
Set the Power Switch to “OFF”. Connect the AC
Adapter to the camcorder 4.
Battery pack
3
Plug the AC Adapter into an AC outlet 5.
CHARGE Lamp
The CHARGE lamp on the camcorder blinks to
indicate charging has started.
4
When the CHARGE lamp stops blinking but stays
lit, charging is finished. Unplug the AC Adapter from
the AC outlet. Disconnect the AC Adapter from the
camcorder.
AC Adapter
To Detach The Battery Pack . . .
..... Press BAT. RELEASE and pull out the battery
pack.
5
To DC
connector
4
To AC outlet
NOTES:
● If the protective cap is attached to the battery pack,
remove it first.
● During charging, the camcorder cannot be operated.
● Charging is not possible if the wrong type of battery is
used.
● When charging the battery pack for the first time or
after a long storage period, the CHARGE lamp may not
light. In this case, remove the battery pack from the
camcorder, then try charging again.
Battery pack
Charging time
approx. 1 hr. 30 min.
approx. 3 hrs.
BN-V408U
BN-V416U (optional)
BN-V428U (optional)
approx. 5 hrs.
● If the battery operation time remains extremely short
even after having been fully charged, the battery is
worn out and needs to be replaced. Please purchase a
new one.
● Using the optional AA-V40U AC Power Adapter/
Charger, you can charge the BN-V408U/V416U/V428U
battery pack without the camcorder. However, it cannot
be used as an AC adapter.
For other notes, ੬ pg. 47
EN
9
ATTENTION
USING THE BATTERY PACK
Before detaching the power source, make sure that
the camcorder’s power is turned off. Failure to do so
can result in a camcorder malfunction.
Perform step 1 of “CHARGING THE BATTERY
PACK” (੬ pg. 8).
Approximate recording time
NOTES:
Battery
pack
● Recording time is reduced significantly under the
following conditions:
LCD monitor on
1 hr.
Viewfinder on
BN-V408U
1 hr. 15 min.
2 hrs. 30 min.
• Zoom or Record-Standby mode is engaged
repeatedly.
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
BN-V416U
(optional)
2 hrs.
BN-V428U
(optional)
3 hrs. 30 min.
5 hrs.
4 hrs. 20 min.
6 hrs. 10 min.
8 hrs. 40 min.
BN-V840U
(optional)
BN-V856U
(optional)
7 hrs.
INFORMATION
The extended-use battery pack kit is a set composed of a battery pack and AC Power Adapter/Charger:
VU-V840 KIT: BN-V840U battery pack & AA-V15U AC Power Adapter/Charger
VU-V856 KIT: BN-V856U battery pack & AA-V80U AC Power Adapter/Charger
Read the kit's instruction manual before using.
Also, by using the optional JVC VC-VBN856U DC Cord, it will be possible to connect BN-V840U or BN-V856U
battery packs to the camcorder and supply power directly to the camcorder.
USING AC POWER
Use the AC Adapter (connect as shown in the
illustration).
NOTES:
AC Adapter
● The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
● For other notes, ੬ pg. 47.
To DC connector
To AC outlet
About Batteries
DANGER! Do not attempt to take the batteries apart,
or expose them to flame or excessive heat, as it may
cause a fire or explosion.
WARNING! Do not allow the battery or its terminals
to come in contact with metals, as this can result in a
short circuit and possibly start a fire.
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have a large
Lithium-ion is vulnerable in colder temperatures.
power capacity. However, when one is exposed to
cold temperatures (below 10°C/50°F), its usage time
becomes shorter and it may cease to function. If this
happens, place the battery pack in your pocket or
other warm, protected place for a short time, then re-
attach it to the camcorder. As long as the battery pack
itself is not cold, it should not affect performance.
(If you’re using a heating pad, make sure the battery
pack does not come in direct contact with it.)
10EN
GETTING STARTED (cont.)
Grip Adjustment
Power Zoom Lever
1
2 Separate the Velcro strip.
Pass your right hand through the loop and grasp
the grip.
Recording
Start/Stop
button
3
Adjust your thumb and fingers through the grip, to
easily operate the Recording Start/Stop button and
Power Switch and Power Zoom Lever. Be sure to
fasten the Velcro strip to your preference.
Power Switch
Viewfinder Adjustment
1
Set the Power Switch to “ ” or “ ” while
pressing down the Lock Button located on the switch.
Diopter
Adjustment Control
2
Turn the Diopter Adjustment Control until the
indications in the viewfinder are clearly focused.
PAUSE
Shoulder Strap Attachment
1
Make sure the battery pack is removed. Following
the illustration, thread the strap through the eyelet 1,
then fold it back and thread it through the buckle 2.
Repeat the procedure to attach the other end of the
strap to the other eyelet 3 located under the Grip
Strap . Confirm the strap is not twisted.
1
2
3
Tripod Mounting
CAUTION
When attaching the camcorder to a tripod, extend its
legs to stabilize the camcorder. It is not advised to
use small sized tripods. This may cause damage to
the unit by falling over.
1
To attach the camcorder to a tripod, align the
direction stud and screw to the mounting socket and
stud hole on the camcorder. Then tighten the screw
clockwise. Some tripods are not equipped with studs.
EN 11
MENU/BRIGHT Wheel
Power Lamp
Date/Time Settings
The date/time is recorded onto the tape at all times,
but its display can be turned on or off during playback
(੬ pg. 36, 37).
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch. The
power lamp lights and the camcorder is turned on.
2
Press the MENU/BRIGHT wheel in to access the
Menu Screen.
3
Rotate the MENU/BRIGHT wheel to select
DISPLAY”. Press it and the DISPLAY Menu
appears.
“
Lock Button
4
Rotate the MENU/BRIGHT wheel to select
Power Switch
“CLOCK ADJ.”. Press it and “month” is highlighted.
Rotate the MENU/BRIGHT wheel to input the month.
Press it. Repeat to input the day, year, hour and
minute.
Display
Rotate the MENU/BRIGHT wheel to select
W I P E / FADER
OF
F
PROGRAM AE
EXPOSURE
W. BALANCE
CAMERA
MANUAL
SYSTEM
D I SPLAY
“
RETURN”, and press it twice. The Menu Screen
closes.
NOTE:
Even if you select “CLOCK ADJ.”, if the parameter is not
highlighted the camcorder’s internal clock continues to
operate. Once you move the highlight bar to the first date/
time parameter (month), the clock stops. When you finish
setting the minute and press the MENU/BRIGHT wheel
in, the date and time begin operation from the date and
time you just set.
END
DISPLAY Menu
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
OFF
DEC 25 ’02
5 : 30 PM
ADJ .
RETURN
CLOCK
ADJ .
DEC 25 ’02
5 : 30 PM
12EN
GETTING STARTED (cont.)
Loading/Unloading A Cassette
The camcorder needs to be powered up to load or
eject a cassette.
Erase protection tab*
Make sure the
window side is
facing out.
1
Slide and hold OPEN/EJECT in the direction of
the arrow then pull the cassette holder cover open
until it locks. The cassette holder opens automatically.
• Do not touch internal components.
PUSH HERE
Cassette
holder
2
Insert or remove a tape and press “PUSH HERE”
to close the cassette holder.
• Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
• When the battery’s charge is low, you may not be
able to close the cassette holder cover. Do not apply
force. Replace the battery with a fully charged one
before continuing.
3
Close the cassette holder cover firmly until it
locks into place.
Cassette holder cover
OPEN/EJECT Switch
Approximate recording time
Recording mode
* To Protect Valuable Recordings . . .
.... slide the erase protection tab on the back of the
tape in the direction of “SAVE”. This prevents the
tape from being recorded over. To record on this
tape, slide the tab back to “REC” before loading it.
Tape
SP
LP
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
45 min.
90 min.
120 min.
Be sure to press only the section labeled “PUSH
HERE” to close the cassette holder; touching other
parts may cause your finger to get caught in the
cassette holder, resulting in injury or product damage.
NOTES:
● It takes a few seconds for the cassette holder to open. Do not apply force.
● If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the
cassette holder still does not open, turn the camcorder off then on again.
● If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later,
insert it again.
● When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the
cassette holder cover.
● Closing the cassette holder cover before the cassette holder comes out may cause damage to the camcorder.
● Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder is closed
with the camcorder switched off, however, it may not recede. It is recommended to turn the power on before loading or
unloading.
● When resuming recording, once you open the cassette holder cover a blank portion will be recorded on the tape or a
previously recorded scene will be erased (recorded over) regardless of whether the cassette holder came out or not.
See page 18 for information about recording from the middle of a tape.
EN 13
MENU/BRIGHT Wheel
Power Lamp
Recording Mode Setting
Set the tape recording mode depending on your
preference.
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch. The
power lamp lights and the camcorder is turned on.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select
CAMERA” and press it. The CAMERA Menu
appears.
“
Lock Button
4
Rotate the MENU/BRIGHT wheel to select “REC
MODE” and press it. The Sub Menu appears. Select
“SP” or “LP” by rotating the MENU/BRIGHT wheel
and press it. Rotate the MENU/BRIGHT wheel to
Power Switch
select “
RETURN”, and press it twice. The Menu
Screen closes.
Display
• Audio Dubbing (੬ pg. 43) and Insert Editing
(੬ pg. 44) are possible on tapes recorded in the
SP mode.
• “LP” (Long Play) is more economical, providing
1.5 times the recording time.
Menu Screen
Sub Menu
REC MODE
–
SP
LP
NOTES:
● If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
● It is recommended that tapes recorded in the LP mode
on this camcorder be played back on this camcorder.
● During playback of a tape recorded on another
camcorder, blocks of noise may appear or there may be
momentary pauses in the sound.
14EN
RECORDING & PLAYBACK
RECORDING
&
PLAYBACK
CONTENTS
RECORDING ................................. 15 – 18
Basic Recording..................................... 15
Journalistic Shooting ............................... 16
Self-Recording ...................................... 16
Operation Mode .................................... 16
Zooming ............................................ 17
Time Code ........................................... 18
PLAYBACK ................................... 19 – 22
Normal Playback ................................... 19
Still Playback ....................................... 19
Shuttle Search ...................................... 19
Frame-By-Frame Playback ........................ 19
Connections .................................. 20 – 21
Blank Search ........................................ 22
EN 15
RECORDING
Power lamp
Basic Recording
Power Switch
NOTE:
You should already have performed the procedures
listed below. If not, do so before continuing.
● Power (੬ pg. 8)
● Grip Adjustment (੬ pg. 10)
● Viewfinder Adjustment (੬ pg. 10)
● Load A Cassette (੬ pg. 12)
● Recording Mode Setting (੬ pg. 13)
1
2 Remove the lens cap.
Set the Power Switch to “ ” or “ ” while
During
shooting
Lock Button
pressing down the Lock Button located on the switch.
Shooting while using the LCD monitor: Make sure
the LCD monitor is fully open. Tilt it upward/
downward for best viewability.
Shooting while using the viewfinder: Close the
LCD monitor.
Recording Start/Stop Button
Display
25min
Tape remaining time
indicator (Approximate)
• The power lamp lights and the camcorder enters the
Record-Standby mode. “PAUSE” is displayed.
3
Press the Recording Start/Stop Button. “
appears while recording is in progress.
”
min
3 min
90 min
0 min
89 min
(Now calculating)
To Stop Recording . . .
..... press the Recording Start/Stop Button. The
1 min
(Blinking)
2 min
(Blinking)
camcorder re-enters the Record-Standby mode.
(Blinking)
To Adjust The Brightness Of The Display . . .
..... rotate the MENU/BRIGHT wheel until the bright
level indicator on the display moves and the
appropriate brightness is reached.
BR I GHT
NOTES:
● If the Record-Standby mode continues for 5 minutes,
the camcorder’s power shuts off automatically. To turn
the camcorder on again, set the Power Switch to
“OFF”, then back to “ ” or “ ”.
MENU/BRIGHT Wheel
● The image will not appear simultaneously on the LCD
monitor and the viewfinder. It will appear in the
viewfinder when the LCD monitor is in the lock position,
and it will appear on the LCD monitor when fully
extended.
● When a blank portion is left between recorded scenes
on the tape, the time code is interrupted and errors may
occur when editing the tape. To avoid this, refer to
“Recording from the middle of a tape” (੬ pg. 18).
● To turn the beep sounds off, ੬ pg. 32, 34.
PUSH OPEN Button
For other notes, ੬ pg. 47
16EN
RECORDING (cont.)
JOURNALISTIC SHOOTING
In some situations, different shooting angles may
provide more dramatic results. Hold the camcorder in
the desired position and tilt the LCD monitor in the
most convenient direction. It can rotate 270° (90°
downward, 180° upward).
Self-
Recording
SELF-RECORDING
You can shoot yourself while viewing your own image
in the LCD monitor. Open the LCD monitor and tilt it
upward 180° so that it faces forward, then point the
lens toward yourself and start recording.
To turn on the camcorder, set the Power Switch to
any operation mode except “OFF”while pressing
down the Lock Button located on the switch.
Operation Mode
Choose the appropriate operation mode according to
your preference using the Power Switch.
Power Switch
Power Switch Position
(Manual):
Allows you to set various recording functions using the
Menus. If you want more creative capabilities than Full
Auto recording, try this mode.
Power lamp
Lock Button
(Full Auto):
Allows you to record using NO special effects or
manual adjustments. Suitable for standard recording.
OFF:
Allows you to switch off the camcorder.
PLAY:
• Allows you to play back a recording on the tape.
• Allows you to transfer a still image recorded on the
tape to a computer.
When the Power Switch is set to “ ”, “
”
appears. When set to “ ” or “PLAY”, there is no
indication.
EN 17
Zoom in (T: Telephoto)
FEATURE: Zooming
PURPOSE:
1x
W
T
10x
W
T
To produce the zoom in/out effect, or an instanta-
neous change in image magnification.
20x
W
T
40x
W
T
OPERATION:
Zoom In
Slide the Power Zoom Lever towards “T”.
Zoom Out
Zoom out (W: Wide angle)
Slide the Power Zoom Lever towards “W”.
Ⅲ The further you slide the Power Zoom Lever, the
quicker the zoom action.
Zoom display
NOTES:
● Focusing may become unstable during Zooming. In
this case, set the zoom while in Record-Standby,
lock the focus by using the manual focus
(੬ pg. 29), then zoom in or out in Record mode.
● Zooming is possible to a maximum of 700X, or it
can be switched to 16X magnification using the
optical zoom (੬ pg. 33).
● Zoom magnification of over 16X is done through
Digital image processing, and is therefore called
Digital Zoom.
16x
W
T
Digital zoom zone
16X (optical)
zoom zone
Approximate zoom ratio
● During Digital zoom, the quality of image may
suffer.
● Macro shooting (as close as approx. 5 cm (2") to
the subject) is possible when the Power Zoom
Lever is set all the way to “W”. Also see “TELE
MACRO” in the Menu Screen on page 34.
Power Zoom Lever
18EN
RECORDING (cont.)
Time Code
During recording, a time code is recorded on the tape. This code is to confirm the location of the recorded
scene on the tape during playback.
If recording starts from a blank portion, the time code begins counting from “00:00:00”
(minute:second:frame). If recording starts from the end of a previously recorded scene, the time code
continues from the last time code number.
If during recording a blank portion is left partway through the tape, the time code is interrupted. When
recording is resumed, the time code starts counting up again from “00:00:00”. This means the camcorder
may record the same time codes as those existing in a previously recorded scene. To prevent this, perform
“Recording From The Middle of A Tape” below in the following cases;
• When shooting again after playing back a
recorded tape.
• When power shuts off during shooting.
• When a tape is removed and re-inserted during
shooting.
Display
Frames are not displayed
during recording.
Minutes
• When shooting using a partially recorded tape.
• When shooting on a blank portion located
partway through the tape.
• When shooting again after shooting a scene
then opening/closing the cassette holder cover.
Seconds
Frames
(30 frames = 1 second)
12 : 34 : 24
Recording From The Middle Of A Tape
1. Play back a tape or use Blank Search (੬ pg. 22) to find the spot at which you want to start recording,
then engage the Still Playback mode (੬ pg. 19).
2. Set the Power Switch to “ ” or “ ” while pressing down the Lock Button located on the switch, then
start recording.
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time code indication does not move smoothly.
● The time code is displayed only when “TIME CODE” is set to “ON” (੬ pg. 35, 37).
When a blank portion is recorded on a tape
Time code
00:00:00
Time code
05:43:21
Time code
00:00:00
Tape
Already recorded scene
Blank
Newly recorded scene
Shooting start point
Shooting stop point
Shooting start point
Proper recording
Time code
00:00:00
Time code
05:43:21
Time code
05:44:00
Tape
Already recorded scene
New scene
Latest scene
Shooting start point
Shooting start point
Shooting start point
EN 19
PLAYBACK
Play/Pause Button (4/6)
Power Zoom Lever
(VOL.)
Normal Playback
Rewind Button (2
)
1
2 Load a tape (੬ pg. 12).
Set the Power Switch to “PLAY” while pressing down
Fast-Forward
Stop Button (5)
Button (3
)
the Lock Button located on the switch. To start playback,
press 4/6.
• To stop playback, press 5.
• Press
2
to rewind, or
3
to fast-forward the tape
during Stop mode.
To Control The Speaker Volume . . .
..... slide the Power Zoom Lever (VOL.) towards “+”
to turn up the volume, or towards “–” to turn down
the volume.
Speaker
NOTES:
● If Stop mode continues for 5 minutes when power is supplied from a battery, the camcorder shuts off automatically. To
turn on again, set the Power Switch to “OFF”, then to “PLAY”.
● The playback picture can be viewed in the LCD monitor, viewfinder or on a connected TV (੬ pg. 20).
● You can also view the playback picture on the LCD monitor with it flipped over and pushed against the camera body.
● LCD monitor/viewfinder indications:
• When power is supplied from a battery: the “
” battery pack remaining power indicator is displayed.
When power is supplied from an AC outlet: “
” does not appear.
• During Stop mode, none of the indications are displayed.
● When a cable is connected to the AV connector, the sound is not heard from the speaker.
Still Playback: Pauses during playback.
1) Press 4/6 during playback.
2) To resume normal playback, press 4/6 again.
● If still playback continues for more than about 3 minutes, the camcorder’s Stop mode is automatically engaged.
After 5 minutes in the Stop mode, the camcorder’s power is automatically turned off.
● When 4/6 is pressed, the image may not pause immediately while the camcorder stabilizes the still image.
Shuttle Search: Allows high-speed search in either direction.
1) Press
2) To resume normal playback, press 4/6.
● During playback, press and hold or 3. The search continues as long as you hold the button. Once you
release it, normal playback resumes.
3
for forward or
2
for reverse search during playback.
2
● A slight mosaic effect appears on screen during Shuttle Search. This is not a malfunction.
Frame-By-Frame Playback: Allows frame-by-frame search.
1) Engage Still Playback.
2) Rotate the MENU/BRIGHT wheel towards “+” for forward Frame-By-Frame Playback, or towards “–” for
reverse Frame-By-Frame Playback during Still Playback.
● To resume normal playback, press 4/6.
ATTENTION
During Shuttle Search, parts of the picture may not be clearly visible, particularly on
the left side of the screen.
20EN
PLAYBACK (cont.)
Connections
These are some basic types of connections. When making the connections, refer also to your VCR and TV
instruction manuals.
A. Connection to a TV or VCR equipped with an S-VIDEO IN and A/V input
connectors
To TV or VCR
To AV
White to
AUDIO L IN**
TV
Red to
AUDIO R IN**
Audio/Video cable
(provided)
Yellow:
Not connected
Connector
cover*
VCR
To S-VIDEO
S-Video cable
(optional)
To S-VIDEO IN
* When connecting the cables, open this cover.
** The Audio cable is not required for watching still images only.
B. Connection to a TV or VCR equipped only with A/V input connectors
To TV or VCR
TV
To AV
White to
AUDIO L IN**
Red to
AUDIO R IN**
Audio/Video cable
(provided)
Yellow to
VIDEO IN
VCR
Connector cover*
* When connecting the cables, open this cover.
** The Audio cable is not required for watching still images only.
EN 21
NOTES:
1
2 Make sure all units are turned off.
Connect the camcorder to a TV or VCR as shown
in the illustration (੬ pg. 20).
If using a VCR . . . go to step 3.
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 9).
● The S-Video cable is optional. Be sure to use the
YTU94146A S-Video cable.
Consult the JVC Service Center described on the
sheet included in the package for details on its
availability. Make sure to connect the end with a
core filter to the camcorder. The core filter reduces
interference.
3 If not . . . go to step 4.
Connect the VCR output to the TV input, referring
to your VCR’s instruction manual.
● To monitor the picture and sound from the camcorder
without inserting a tape, set the camcorder’s Power
Switch to “ ” or “ ”, then set your TV to the
appropriate input mode.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound when
the camcorder is turned on.
● If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the TV
as interference will occur in the camcorder playback
picture.
● While the Audio/Video cable is connected to the AV
connector, sound cannot be heard from the speaker.
4
5 Turn on the camcorder, the VCR and the TV.
Set the VCR to its AUX input mode, and set the
TV to its VIDEO mode.
To choose whether or not the following displays
appear on the connected TV . . .
• Date/Time
..... set “DATE/TIME” to “AUTO”, “ON” or “OFF” in the
Menu Screen (੬ pg. 36).
• Time Code
..... set “TIME CODE” to “ON” or “OFF” in the Menu
Screen (੬ pg. 36).
• Playback Sound Mode, Tape Speed And Tape
Running Displays for tape playback
..... set “ON SCREEN” to “LCD” or “LCD/TV” in the
Menu Screen (੬ pg. 36).
22EN
PLAYBACK (cont.)
BLANK SEARCLH Button
Blank Search
Helps you find where you should start recording in
the middle of a tape to avoid time code interruption
(੬ pg. 18).
1
2 Load a tape (੬ pg. 12).
Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
3
Press BLANK SEARCH.
• “BLANK SEARCH” appears blinking and the
camcorder automatically starts reverse or forward
shuttle search, then stops at the spot which is about
3 seconds of tape before the beginning of the
detected blank portion.
Lock Button
Power Switch
To cancel Blank Search midway . . .
..... press 5.
Display
44
NOTES:
● In step 3, if the current position is at a blank portion the
camcorder searches in the reverse direction, and if the
current position is at a recorded portion the camcorder
searches in the forward direction.
BLANK SEARCH
● Blank Search does not work if “HEAD CLEANING
REQUIRED. USE CLEANING CASSETTE” has
appeared with the tape.
● If the beginning or end of the tape is reached during
Blank Search, the camcorder stops automatically.
● A blank portion which is shorter than 5 seconds of tape
may not be detected.
Stop Button (5)
● The detected blank portion may be located between
recorded scenes. Before you start recording, make sure
there is no recorded scene after the blank portion.
EN 23
ADVANCED FEATURES
ADVANCED FEATURES
CONTENTS
FOR RECORDING ........................................... 24 – 31
Night-Alive ............................................................ 24
Program AE With Special Effects .............................24 – 25
Fade/Wipe Effects .............................................26 – 27
Snapshot ............................................................... 28
Auto Focus/Manual Focus ............................................ 29
Exposure Control ...................................................... 30
Iris Lock ................................................................ 30
White Balance Adjustment ........................................... 31
Manual White Balance Operation.................................... 31
USING MENUS FOR DETAILED ADJUSTMENT............. 32 – 37
For Recording Menu............................................32 – 35
For Playback Menu ............................................36 – 37
DUBBING .................................................... 38 – 39
Dubbing To A VCR..................................................... 38
Dubbing To Or From A Video Unit Equipped With A DV Connector .... 39
USING THE OPTIIONAL REMOTE CONTROL UNIT ........ 40 – 44
Installing The Battery ................................................. 40
Playback Zoom ........................................................ 42
Audio Dubbing ......................................................... 43
Insert Editing .......................................................... 44
SYSTEM CONNECTIONS ............................................45
Connection To A Personal Computer ................................. 45
24EN
FOR RECORDING
NOTES:
Night-Alive
● During Night-Alive, the following functions or settings
cannot be activated and its indicator blinks or goes out:
• Some modes of “Program AE With Special Effects”
(੬ pg. 24, 25).
• “GAIN UP” in the CAMERA Menu (੬ pg. 33).
• “DIS” in the MANUAL Menu (੬ pg.33).
● During Night-Alive, it may be difficult to bring the
camcorder into focus. To prevent this, use of manual
focus and/or a tripod is recommended.
Makes dark subjects or areas even brighter than they
would be under good natural lighting. Although the
recorded image is not grainy, it may look as if it is
strobing due to the slow shutter speed.
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch.
2
Press NIGHT ALIVE so that the Night-Alive
indicator “ ”appears.
• The shutter speed is automatically adjusted to
provide up to 30 times sensitivity.
• “A” appears beside “
” while the shutter speed is
being automatically adjusted.
MENU/BRIGHT Wheel
To Deactivate Night-Alive . . .
..... press NIGHT ALIVE again so that the Night-Alive
indicator disappears.
Program AE With Special Effects
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch.
Lock Button
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
Power Switch
3
Rotate the MENU/BRIGHT wheel to select
PROGRAM AE”, then press it.
“
NIGHT ALIVE Button
4
Rotate the MENU/BRIGHT wheel to select the
desired mode (੬ pg. 25), then press it. Selection is
complete. Press the MENU/BRIGHT wheel in again.
The Menu Screen closes.
• The PROGRAM AE Menu disappears and the
selected mode is activated. The selected mode
indicator appears.
To Deactivate The Selected Mode . . .
..... select “OFF” in step 4.
NOTES:
Display
● Program AE with special effects can be changed during
recording or during Record-Standby.
● Some modes of Program AE special effects cannot be
used during Night-Alive.
ᮡ
SNO
W
SPOTL I GHT
I L I GHT
TW
SEP I A
MONOTONE
CLASS I C F I LM
STROBE
IMPORTANT
SLO
W
4
X
Some modes of Program AE with special effects
cannot be used with certain Fade/Wipe Effects
(੬ pg. 26, 27). If an unusable mode is selected, its
indicator blinks or goes out.
OFF
ᮢ
EN 25
SEPIA
SHUTTER
Recorded scenes have a brownish tint like old
photos. Combine this with the Cinema mode for a
classic look.
1/60–The shutter speed is fixed at 1/60th of a
second. Black bands that usually appear when
shooting a TV screen become narrower.
1/100–The shutter speed is fixed at 1/100th of a
second. The flickering that occurs when shooting
under a fluorescent light or mercury-vapor lamp is
reduced.
MONOTONE
Like black and white films, your footage is shot in
B/W. Used together with the Cinema mode, it
enhances the “classic film” effect.
SPORTS
(Variable
Shutter Speed:
1/250 – 1/4000)
CLASSIC FILM
Gives recorded scenes a strobe effect.
This setting allows fast-moving images to be
captured one frame at a time, for vivid, stable slow-
motion playback. The faster the shutter speed, the
darker the picture becomes. Use the shutter
function under good lighting conditions.
SNOW
Compensates for subjects that may otherwise
appear too dark when shooting in extremely bright
surroundings such as in the snow.
STROBE
Your recording looks like a series of consecutive
snapshots.
SPOTLIGHT
Compensates for subjects that may otherwise
appear too bright when shooting under extremely
strong direct lighting such as spotlights.
SLOW (Slow Shutter)
Lights dark subjects or areas even brighter than
they would be under good natural lighting. Use
“SLOW” only in dark areas.
NOTE:
“SPOTLIGHT” has the same effect as –3 with the
exposure control (੬ pg. 30).
SLOW 4X
Slow Shutter raises light sensitivity to allow
shooting in dark environments.
NOTES:
● When using “SLOW”, the image takes on a strobe-
like effect.
● When using “SLOW”, it may be difficult to bring the
camcorder into focus. To prevent this, use of manual
focus and/or a tripod is recommended.
TWILIGHT
Makes evening scenes look more natural.
White Balance (੬ pg. 31) is initially set to
can be changed to your desired setting. When
, but
Twilight is chosen, the camcorder automatically
adjusts the focus from approx. 10 m (32 ft) to
infinity. From less than 10 m (32 ft), adjust the
focus manually.
26EN
FOR RECORDING (cont.)
Fade/Wipe Effects
These effects let you make pro-style scene
transitions. Use them to spice up the transition from
one scene to the next.
IMPORTANT
Some Fade/Wipe Effects cannot be used with certain
modes of Program AE with special effects (੬ pg. 24,
25). If an unusable Fade/Wipe Effect is selected, its
indicator blinks or goes out.
Fade or Wipe works when tape recording is started or
when you stop recording.
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch.
MENU/BRIGHT Wheel
Power Switch
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select “
WIPE/FADER”, then press it.
4
Rotate the MENU/BRIGHT wheel to select the
desired function, then press it. Selection is complete.
Press the MENU/BRIGHT wheel in again.
• The WIPE/FADER Menu disappears and the effect
is reserved. The indicator representing the selected
effect appears.
5
Press the Recording Start/Stop Button to activate
the Fade-in/out or Wipe-in/out.
Lock Button
To Deactivate The Selected Effect . . .
..... select “OFF” in step 4.
Recording Start/Stop Button
NOTE:
You can extend the length of a Fade or Wipe by pressing
and holding the Recording Start/Stop Button.
EN 27
Fader And Wipe Menu
Menu
Effect
Fade in or out with a white screen.
FADER — WHITE
Fade in or out with a black screen.
FADER — BLACK
FADER — B.W
Fade in to a color screen from a black and white screen, or fade out
from color to black and white.
Wipe in on a black screen from the upper right to the lower left corner,
or wipe out from lower left to upper right, leaving a black screen.
WIPE — CORNER
The scene starts in the center of a black screen and wipes in toward
the corners, or comes in from the corners, gradually wiping out to the
center.
WIPE — WINDOW
WIPE — SLIDE
Wipe in from right to left, or wipe out from left to right.
Wipe in as the two halves of a black screen open to the left and right,
revealing the scene, or wipe out and the black screen reappears from
left and right to cover the scene.
WIPE — DOOR
The scene wipes in from the bottom to the top of a black screen, or
wipes out from top to bottom, leaving a black screen.
WIPE — SCROLL
WIPE — SHUTTER
Wipe in from the center of a black screen toward the top and bottom,
or wipe out from the top and bottom toward the center leaving a black
screen.
28EN
FOR RECORDING (cont.)
SNAPSHOT Button
Snapshot
This feature lets you record still images that look like
photographs onto a tape.
SNAPSHOT MODE SELECTION
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
Lock Button
Power Switch
3
Rotate the MENU/BRIGHT wheel to select
CAMERA”. Press it and the CAMERA Menu
“
appears.
4
Rotate the MENU/BRIGHT wheel to select
“SNAP MODE”, then press it.
Display
Menu Screen
5
Rotate the MENU/BRIGHT wheel to select the
desired Snapshot mode, then press it.
Rotate the MENU/BRIGHT wheel to select
SNAP MODE
–
FULL
P I N–UP
FRAME
“
RETURN” and press it twice. The Menu Screen
closes.
SNAPSHOT RECORDING
1
Press SNAPSHOT. “PHOTO” appears while the
snapshot is being taken.
FULL
Snapshot mode with no
frame
If you press during Record-Standby . . .
..... “PHOTO” appears and a still image will be recorded
for approx. 6 seconds, then the camcorder re-enters
the Record-Standby mode.
If you press during Recording . . .
..... “PHOTO” appears and a still image will be recorded
for approx. 6 seconds, then the normal recording
resumes.
• Regardless of the Power Switch position (“ ” or “ ”),
Snapshot recording takes place using the selected
Snapshot mode.
PIN-UP
Pin-Up mode
Motor Drive Mode
Keeping SNAPSHOT pressed provides an effect similar
to serial photography. (Interval between still images:
approx. 1 second)
NOTES:
● To remove the shutter sound, ੬ “BEEP” on pg. 32, 34.
● If Snapshot recording is not possible, “PHOTO” blinks
when SNAPSHOT is pressed.
● If Program AE with special effects (੬ pg. 24) is
engaged, certain modes of Program AE with special
effects are disabled during Snapshot recording. In such
a case, the icon blinks.
FRAME
Snapshot mode with
frame
● If SNAPSHOT is pressed when “DIS” is set to “ON”
(੬ pg. 33), the Stabilizer will be disabled.
● During playback as well, all Snapshot modes are
available. The shutter sound is not heard.
● During Snapshot recording, the image displayed in the
viewfinder may be partially missing. However, there is
no effect in the recorded image.
There is the sound effect of a shutter closing.
● When a cable is connected to the AV connector, the
shutter sound is not heard from the speaker, however it
is recorded onto the tape.
EN 29
Focus detection zone
While focusing on a further
subject
While focusing on a nearer
subject
FEATURE: Auto Focus
PURPOSE:
The camcorder’s Full Range AF system offers continuous shooting ability from close-up (as close as approx.
5 cm (2") to the subject) to infinity.
However, correct focus may not be obtainable in the situations listed below (in these cases use manual
focusing):
• When two subjects overlap in the same scene.
• When illumination is low.*
• When the subject has no contrast (difference in brightness and darkness), such as a flat, one-color
wall, or a clear, blue sky.*
• When a dark object is barely visible in the viewfinder.*
• When the scene contains minute patterns or identical patterns that are regularly repeated.
• When the scene is affected by sunbeams or light reflecting off the surface of a body of water.
• When shooting a scene with a high-contrast background.
* The following low-contrast warnings appear blinking:
,
,
and
NOTES:
● If the lens is smeared or blurred, accurate focusing is not possible. Keep the lens clean, wiping with a piece of soft
cloth if it gets dirty. When condensation occurs, wipe with a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens, zoom out first (੬ pg. 17). If zoomed-in in the auto focus mode, the
camcorder may automatically zoom out depending on the distance between the camcorder and the subject. This
will not occur when “TELE MACRO” (੬ pg. 34) is activated.
FEATURE: Manual Focus
PURPOSE:
To obtain correct focus.
OPERATION:
1) If you are using the viewfinder, you should already have made the necessary viewfinder adjustments
(੬ pg. 10).
2) Set the Power Switch to “ ” while pressing down the Lock Button located on the switch, then press
FOCUS (੬ pgs. 58 and 59, 7 FOCUS Button). The manual focus indicator appears.
3) To focus on a farther subject, rotate the MENU/BRIGHT wheel towards “+”. “ ” appears and blinks.
To focus on a nearer subject, rotate the MENU/BRIGHT wheel towards “–”. “ ” appears and blinks.
4) Press the MENU/BRIGHT wheel in. Focus adjustment is complete.
To reset to Auto Focus, press FOCUS twice or set the Power Switch to “ ”.
If FOCUS is pressed once, the camcorder will enter the focus adjustment mode again.
NOTES:
● Be sure to focus the lens in the maximum telephoto position when you use the Manual Focus mode. If you focus in
on a subject in the wide-angle position, sharply focused images cannot be obtained when zoomed up because the
depth-of-field is reduced at longer focal lengths.
● When the focus level cannot be adjusted any further or closer, “ ” or “ ” will blink.
30EN
FOR RECORDING (cont.)
Exposure Control
Iris Lock
Manual exposure adjustment is recommended in the
following situations:
Use this function in the following situations:
• When shooting a moving subject.
• When shooting using reverse lighting or when the
background is too bright.
• When shooting on a reflective natural background
such as at the beach or when skiing.
• When the background is overly dark or the subject
light.
• When the distance to the subject changes (so its
size in the LCD monitor or the viewfinder changes),
such as when the subject is backing away.
• When shooting on a reflective natural background
such as at the beach or when skiing.
• When shooting objects under a spotlight.
• When zooming.
When the subject is close, keep the iris locked. Even
when the subject moves away from you, the image
will not darken or brighten.
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
Before the following steps, perform steps 1
through 4 of “Exposure Control”.
3
Rotate the MENU/BRIGHT wheel to select “
EXPOSURE”, then press it.
5
Adjust zoom so that the subject fills the LCD
monitor or the viewfinder, then press and hold the
MENU/BRIGHT wheel for over 2 seconds. The
exposure control indicator and “ ” appear.
Press the MENU/BRIGHT wheel in. “ ” changes to
4
Rotate the MENU/BRIGHT wheel to select
“MANUAL”, then press it. The Menu Screen
disappears. The exposure control indicator appears.
“
” and the iris is locked.
5
Rotate the MENU/BRIGHT wheel towards “+” to
brighten the image, or towards “–” to darken the
image. (maximum ±6)
Iris lock indicator
6
Press the MENU/BRIGHT wheel in. Exposure
adjustment is complete.
BACKLIGHT
Button (5)
3
To Return To Automatic Exposure Control . . .
..... select “AUTO” in step 4. Or, set the Power Switch
to “ ”.
MENU/BRIGHT
Wheel
To Brighten The Subject Quickly . . .
..... press BACKLIGHT.
is displayed and the
subject is brightened. If pressed again,
disappears and the brightness returns to the
previous level.
Power Switch
• +3 exposure has the same effect as the
BACKLIGHT Button.
• Using BACKLIGHT may cause the light around the
subject to become too bright and the subject to
become white.
• Backlight compensations is also available when the
Power Switch is set to “ ”.
To Return To Automatic Iris Control . . .
..... rotate MENU/BRIGHT to display “AUTO” then
press it in step 4. The exposure control indicator
and “ ” disappear. Or, set the Power switch to
NOTE:
You cannot use the manual exposure control at the same
time with backlight, spotlight (੬ pg. 25) compensation
and “SNOW” (੬ pg. 25).
“
”.
To Lock The Exposure Control And The Iris . . .
..... after step 4 of “Exposure Control”, adjust the
exposure rotating the MENU/BRIGHT wheel.
Then lock the iris in step 5 of “Iris Lock”. For
automatic locking, rotate the MENU/BRIGHT
wheel to select “AUTO”, then press it in step 4.
The iris becomes automatic after about 2
seconds.
Iris
Like the pupil of the human eye, it contracts in well-lit
environments to keep too much light from entering,
and dilates in dim environments to allow in more light.
EN 31
White Balance Adjustment
Manual White Balance Operation
A term that refers to the correctness of color
reproduction under various lighting. If the white
balance is correct, all other colors will be accurately
reproduced.
Perform Manual White Balance when shooting under
various types of lighting.
1
Follow steps 1 through 4 of the white balance
adjustment, and select “ MWB”.
The white balance is usually adjusted automatically.
However, more advanced camcorder operators
control this function manually to achieve a more
professional color/tint reproduction.
2
Hold a sheet of plain white paper in front of the
subject. Adjust zoom or position yourself so that the
white paper fills the screen.
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch.
3
Press the MENU/BRIGHT wheel in until
begins blinking rapidly.
When the setting is completed,
blinking.
resumes normal
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
4 Press the MENU/BRIGHT wheel in twice. The
Menu Screen closes and the Manual White Balance
indicator is displayed.
3
Rotate the MENU/BRIGHT wheel to select
W.BALANCE”, then press it. The W.BALANCE
Menu appears.
“
4
Rotate the MENU/BRIGHT wheel to select the
desired mode.
MENU/BRIGHT Wheel
“AUTO” ................. White balance is adjusted
automatically (factory preset).
“
“
“
“
MWB” ............ White balance is set manually.
FINE” ............. Outdoors on a sunny day.
CLOUD” ........ Outdoors on a cloudy day.
HALOGEN” ... A video light or similar type of
lighting is used.
White paper
5
Press the MENU/BRIGHT wheel in. Selection is
complete. Press the MENU/BRIGHT wheel in again.
The Menu Screen closes and the selected mode
indicator except “AUTO” appears.
Power Switch
To Return To Automatic White Balance . . .
..... select “AUTO” in step 4. Or, set the Power Switch
to “ ”.
NOTES:
● In step 2, it may be difficult to focus on the white paper.
In such a case, adjust focus manually (੬ pg. 29).
● A subject can be shot under various types of lighting
conditions indoors (natural, flourescent, candlelight,
etc.). Because the color temperature is different
depending on the light source, the subject tint will differ
depending on the white balance settings. Use this
function for a more natural result.
NOTE:
White balance cannot be used when Sepia or Monotone
(੬ pg. 25) is activated.
● Once you adjust white balance manually, the setting is
retained even if the power is turned off or the battery
removed.
32EN
USING MENUS FOR DETAILED ADJUSTMENT
MENU/BRIGHT Wheel
For Recording Menu
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the
more detailed camcorder settings (੬ pg. 33 – 35).
1
Set the Power Switch to “ ” while pressing
down the Lock Button located on the switch.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select the
desired function menu, and press it. The selected
function menu appears.
Lock Button
Power Switch
4
Function menu setting depends on the function.
If you have selected “
WIPE/FADER”,
Display
“
“
PROGRAM AE”, “
W. BALANCE” . . .
EXPOSURE” or
W I P E / FADER
OF
F
Menu Screen
PROGRAM AE
EXPOSURE
W. BALANCE
CAMERA
MANUAL
SYSTEM
D I SPLAY
..... see pg. 33.
If you have selected “
MANUAL”, “
..... go to step 5.
CAMERA”, “
REC MODE
SOUND MODE
ZOOM
SNAP MODE
GA I N UP
–
–
–
–
–
SP
SYSTEM” or “
DISPLAY” . . .
12B I T
40
FULL
AGC
X
END
5
Rotate the MENU/BRIGHT wheel to select the
desired function and press it. The Sub Menu appears.
Then, rotate the MENU/BRIGHT wheel to select the
parameter, and press it. Selection is complete.
RETURN
Sub Menu
6
Rotate the MENU/BRIGHT wheel to select
“
RETURN” and press it twice. The Menu Screen
closes.
D I S
–
OFF
ON
• The
icon represents “END”.
NOTE:
When the Menu Screen is left on for a couple of
minutes, a residual image may be left on the screen
and it may take several seconds for the residual
image to disappear. This is not due to any defect of
the unit.
BEEP
DEMO MODE
CAM RESET
–
–
MELODY
ON
RETURN
ON SCREEN
DATE / T I ME
T I ME CODE
CLOCK
–
–
–
LCD / TV
AUTO
OFF
DEC 25 ’02
ADJ .
5 : 30 PM
RETURN
W I P E / FADER
PROGRAM AE
EXPOSURE
W. BALANCE
CAMERA
MANUAL
SYSTEM
D I SPLAY
END
Normal Screen
EN 33
Menu Screen Explanations
WIPE/FADER
PROGRAM AE
EXPOSURE
Refer to “Fade/Wipe Effects” (੬ pg. 26, 27).
Refer to “Program AE With Special Effects” (੬ pg. 24, 25).
Refer to “Exposure Control” and “Iris Lock” (੬ pg. 30).
W.BALANCE
Refer to “White Balance Adjustment” and “Manual White Balance Operation”
(੬ pg. 31).
REC MODE
Allows you to set the tape recording mode (SP or LP) depending on your
pre-ference (੬ pg. 13).
SOUND
MODE
12BIT
Enables tape recording of stereo sound on four separate channels, and is
recommended for use when performing audio dubbing. (Equivalent to the
32 kHz mode of previous models)
16BIT
16X
Enables tape recording of stereo sound on two separate channels. (Equivalent
to the 48 kHz mode of previous models)
ZOOM
When set to “16X” while using digital zoom, the zoom magnification will reset
to 16X since digital zoom will be disengaged.
40X
Allows you to use the Digital Zoom. By digitally processing and magnifying
images, zooming is possible from 16X (the optical zoom limit), to a maximum
of 40X digital magnification.
700X
Allows you to use the Digital Zoom. By digitally processing and magnifying
images, zooming is possible from 16X (the optical zoom limit), to a maximum
of 700X digital magnification.
SNAP MODE
GAIN UP OFF
AGC
Refer to “Snapshot” (੬ pg. 28).
Allows you to shoot dark scenes with no picture brightness adjustment.
The overall appearance may be grainy, but the image is bright.
AUTO
The shutter speed is automatically adjusted (1/30 — 1/200 sec.). Shooting a
subject in low or poor lighting at 1/30 sec. shutter speed provides a brighter
image than in the AGC mode, but the subject’s movements are not smooth or
natural. The overall appearance may be grainy. While the shutter speed is
being automatically adjusted, “
” is displayed.
DIS
OFF
ON
To compensate for unstable images caused by camera-shake, particularly at
high magnification.
NOTES:
● Accurate stabilization may not be possible if hand shake is excessive, or
under the following conditions:
• When shooting subjects with vertical or horizontal stripes.
• When shooting dark or dim subjects.
• When shooting subjects with excessive backlighting.
• When shooting scenes with movement in various directions.
• When shooting scenes with low-contrast backgrounds.
● Switch off this mode when recording with the camcorder on a tripod.
● The “
” indicator blinks or goes out if the Stabilizer cannot be used.
: Factory-preset
NOTES:
● Settings made in the “
the menu settings can be changed only when the Power Switch is set to “ ”.
● The “ MANUAL” settings are effective only when the Power Switch is set to “ ”.
CAMERA” Menu remain effective whether the Power Switch is set to “ ” or “ ”. However,
CONTINUED ON NEXT PAGE
34EN
USING MENUS FOR DETAILED ADJUSTMENT (cont.)
Menu Screen Explanations (cont.)
TELE
MACRO
OFF
Usually the distance to a subject where the lens is in focus depends on the
zoom magnification. Unless there is a distance more than 1m (3.3 ft.) to the
subject, the lens is out of focus at the maximum telephoto setting. When set to
“ON”, you can shoot a subject as large as possible at a distance of approx. 60
cm (2 ft.).
ON
• Depending on the zoom position, the lens may go out of focus.
WIDE
MODE
Records with no change in the screen ratio. For playback on a TV with a
normal screen ratio.
OFF
Inserts black bands at the top and bottom of the screen. During playback on
wide-screen TVs, the black bands at the top and bottom of the screen are cut
CINEMA
and the screen ratio becomes 16:9.
appears. When using this mode, refer
to your wide-screen TV’s instruction manual. During playback/recording on 4:3
TVs/LCD monitor/viewfinder, black bands are inserted at the top and bottom of
the screen and the image appears like a letterboxed 16:9 movie.
For playback on TVs with an aspect ratio of 16:9. Naturally expands the image
SQUEEZE
to fit the screen without distortion.
appears. When using this mode, refer
to your wide-screen TV’s instruction manual. During playback/recording on 4:3
TVs/LCD monitor/viewfinder, the image is elongated vertically.
WIND
CUT
Disengages the function which cuts down on noise created by wind.
OFF
ON
Helps cut down on noise created by wind. “
” appears. The quality of the
sound will change. This is normal.
BEEP
Even though not heard while shooting, shutter sound is recorded on the tape.
OFF
The beep sounds when the power is turned on or off, and at the beginning and end
BEEP
of recording. Also to activate the shutter sound effect (੬ pg. 28).
Instead of a beep, a melody sounds when any operation is performed. It also
MELODY
activates the shutter sound effect (੬ pg. 28).
: Factory-preset
NOTES:
● The “
MANUAL” settings are effective only when the Power Switch is set to “ ”.
● “
SYSTEM” functions which are set when the Power Switch is set to “ ” are also applied when the Power Switch
is set to “PLAY” (੬ pg. 36).
EN 35
DEMO
MODE
OFF
ON
Automatic demonstration will not take place.
Demonstrates certain functions such as Program AE with special effects, etc.,
and can be used to confirm how these functions operate.
Demonstration starts in the following cases:
• When the Menu Screen is closed after “DEMO MODE” is turned “ON”.
• With “DEMO MODE” set to “ON”, if there is no operation for about 3 minutes
after the Power Switch is set to “ ” or “ ” .
Performing any operation during the demonstration stops the demonstration
temporarily. If no operation is performed for more than 3 minutes after that, the
demonstration will resume.
NOTES:
● If a tape is in the camcorder, the demonstration cannot be turned on.
● “DEMO MODE” remains “ON” even if the camcorder power is turned off.
● If “DEMO MODE” remains “ON”, some functions will not be available. After
viewing demo, set to “OFF”.
CAM
CANCEL
Does not reset all settings to the factory-preset.
RESET
EXECUTE Resets all settings to the factory-preset.
ON
LCD
Keeps the camcorder’s display (except the date, time and time code) from
SCREEN
appearing on the connected TV screen.
LCD/TV
Makes the camcorder’s display appear on screen when the camcorder is
connected to a TV.
DATE/
TIME
OFF
The date/time does not appear.
AUTO
Displays the date/time for approx. 5 seconds in the following cases:
• When the Power Switch is set from “OFF” to “ ” or “ ”.
• When tape playback starts. The camcorder displays the date/time when
scenes are recorded.
• When the date is changed during tape playback.
ON
The date/time is always displayed.
Time code is not displayed.
TIME
CODE
OFF
ON
Time code is displayed on the camcorder and on the connected TV. Frame
numbers are not displayed during recording.
CLOCK ADJ.
Allows you to set the current date and time (੬ pg. 11).
: Factory-preset
NOTES:
● “
SYSTEM” and “
DISPLAY” functions which are set when the Power Switch is set to “ ” are also applied
when the Power Switch is set to “PLAY” (੬ pg. 36). “CLOCK ADJ.” only appears when the Power Switch is set to
”.
● Settings made in the “
menu settings can be changed only when the Power Switch is set to “ ”.
“
DISPLAY” Menu remain effective even when the Power Switch is set to “ ”. However, the
36EN
USING MENUS FOR DETAILED ADJUSTMENT (cont.)
MENU/BRIGHT Wheel
For Playback Menu
Power Switch
1
Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
2
Press the MENU/BRIGHT wheel in. The Menu
Screen appears.
3
Rotate the MENU/BRIGHT wheel to select the
desired function menu, and press it. The selected
function menu appears.
4
Rotate the MENU/BRIGHT wheel to select the
desired function, and press it to display the Sub Menu.
5
Rotate the MENU/BRIGHT wheel to select the
desired parameter and press it. Selection is complete.
Lock Button
Recording Start/Stop Button
6
Rotate the MENU/BRIGHT wheel to select “
RETURN” and press it twice to close the Menu Screen.
Display
Menu Screen Explanations
V I DEO
SOUND MODE
12B I T MODE
REC MODE
SOUND MODE ੬ pg. 37.
SYSTEM
D I SPLAY
12BIT MODE
REC MODE
੬ pg. 37.
Allows you to set the tape
recording mode (SP or LP)
depending on your preference
(੬ pg. 13).
END
It is recommended you use
“REC MODE” in the “
VIDEO” Menu when using this
camcorder as a recorder during
dubbing (੬ pg. 39).
SOUND MODE
12B I T MODE
REC MODE
–
–
–
STEREO
SOUND
SP
1
Each setting is linked with “
DISPLAY” or
“
SYSTEM”, which appears when the Power
Switch is set to “ ” (੬ pg. 34, 35).
The parameters are the same as in the
description on pg. 34, 35.
RETURN
BEEP
DEMO MODE
CAM RESET
–
–
MELODY
ON
NOTE:
“REC MODE” can be set when the Power Switch is set to
“PLAY” or “ ” (੬ pg. 13, 33).
RETURN
ON SCREEN
DATE / T I ME
T I ME CODE
–
–
–
LCD / TV
AUTO
OFF
RETURN
EN 37
Playback Sound
During tape playback, the camcorder detects the sound mode in which the recording was made, and plays the
sound back. Select the type of sound to accompany your playback picture. According to the menu access
explanation on pg. 36, select “SOUND MODE” or “12BIT MODE” from the Menu Screen and set it to the desired
parameter.
STEREO
SOUND L
SOUND R
MIX
Sound is output on both “L” and “R” channels in stereo.
Sound from the “L” channel is output in stereo.
Sound from the “R” channel is output in stereo.
SOUND MODE
12BIT MODE
Original and dubbed sounds are combined and output in stereo on both
“L” and “R” channels in stereo.
SOUND 1
SOUND 2
Original sound is output on both “L” and “R” channels in stereo.
Dubbed sound is output on both “L” and “R” channels in stereo.
: Factory-preset
NOTES:
● The “SOUND MODE” setting is available for both 12-bit and 16-bit sound. (In previous models’ functions, “12-bit” is
called “32 kHz” and “16-bit” is called “48 kHz”.)
● The camcorder cannot detect the sound mode in which the recording was made during fast-forward or rewind. During
playback the sound mode is displayed in the upper left corner.
Display
ON SCREEN setting:
For playback sound, tape
speed and tape running.
DATE/TIME setting:
For date/time.
TIME CODE setting:
For time code.
4
12B I T / SOUND
L
1
SP
6
DEC 25 ’ 02
5 : 30 PM
12 : 34 : 24
Frames*
Seconds
Minutes
*30 frames = 1 second
38EN
DUBBING
Power Switch
Dubbing To A VCR
1
Following the illustration, connect the camcorder
and the VCR. Also refer to pg. 20 and 21.
Connector cover*
2
Set the camcorder’s Power Switch to “PLAY”
while pressing down the Lock Button located on the
switch, turn on the VCR’s power, and insert the
appropriate cassettes in the camcorder and the VCR.
3
4 Engage the VCR’s AUX and Record-Pause modes.
Engage the camcorder’s Play mode to find a spot
To AV
just before the edit-in point. Once it is reached, press
4/6 on the camcorder.
5
Press 4/6 on the camcorder and engage the
VCR’s Record mode.
To
S-VIDEO
6
Engage the VCR’s Record-Pause mode and
press 4/6 on the camcorder.
Audio/Video
cable (provided)
7
Repeat steps 4 through 6 for additional editing,
then stop the VCR and camcorder when finished.
NOTES:
● As the camcorder starts to play your footage it will
appear on your TV. This will confirm the connections
and the AUX channel for dubbing purposes.
● Before you start dubbing, make sure that the
indications do not appear on the connected TV. If they
do, they are being recorded onto the new tape.
S-Video cable
(optional)
White to
AUDIO L IN
To choose whether or not the following displays
appear on the connected TV . . .
Yellow to
VIDEO** IN
Red to
AUDIO R IN
• Date/Time
To S-VIDEO IN
..... set “DATE/TIME” to “AUTO”, “ON” or “OFF” in
the Menu Screen (੬ pg. 36).
• Time Code
VCR
..... set “TIME CODE” to “ON” or “OFF” in the Menu
Screen (੬ pg. 36).
• Playback Sound Mode, Tape Speed And Tape
Running Displays
..... set “ON SCREEN” to “LCD” or “LCD/TV” in the
Menu Screen (੬ pg. 36).
● The S-Video cable is optional. Be sure to use the
YTU94146A S-Video cable.
TV
Consult the JVC Service Center described on the
sheet included in the package for details on its
availability. Make sure to connect the end with a
core filter to the camcorder. The core filter reduces
interference.
* When connecting the cables, open this cover.
** Connect when an S-Video cable is not used.
EN 39
Dubbing To Or From A Video Unit
Equipped With A DV Connector
(Digital Dubbing)
It is also possible to copy recorded scenes from this
camcorder onto another video unit equipped with a
DV connector. Since a digital signal is sent, there is
little if any image or sound deterioration.
To DV
IN/OUT
[To use this camcorder as a player]
1
Make sure all units are turned off. Connect this
camcorder to a video unit equipped with a DV input
connector using a DV cable as shown in the
illustration.
Lock Button
Core filter
2
Set this camcorder’s Power Switch to “PLAY”
while pressing down the Lock Button located on the
switch, turn on the video unit’s power, and insert the
appropriate cassettes in this camcorder and the video
unit.
DV cable
(optional)
Power Switch
3
4
to play back the source tape.
4 Press
While watching the playback on the monitor,
Core filter
engage the DV connector-equipped video unit’s
record mode from the spot on the source tape you
want to begin recording.
To DV
IN/OUT
Video unit equipped
with DV connector
NOTES:
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 9).
● If the remote control is used when both the player and
recorder are JVC video units, both units will perform the
same operation. To prevent this from happening, press
the buttons on both units.
● If a blank portion or disturbed image is played back on
the player during dubbing, the dubbing may stop so that
an unusual image is not dubbed.
● Even though the DV cable is connected correctly,
sometimes the image may not appear in step 4. If this
occurs, turn off the power and make connections again.
● If “Playback Zoom” (੬ pg. 42) or “Snapshot” is
attempted during playback, only the original playback
image recorded on the tape is output from the DV IN/
OUT connector.
● When using a DV cable, be sure to use the optional
JVC VC-VDV204U DV cable.
[To Use This Camcorder As A Recorder]
1. Set this camcorder’s Power Switch to “PLAY” while pressing down the Lock Button located on the switch.
2. Set “REC MODE” to “SP” or “LP” in the Menu Screen (੬ pg. 36).
3. Connect the DV cable as shown in the illustration and load a cassette to record on.
4. Press the Recording Start/Stop button to engage the Record-Pause mode. “
” appears on the screen.
DV. IN
5. Press the Recording Start/Stop button to start recording.
rotates.
6. Press the Recording Start/Stop button again to engage the Record-Pause mode.
stops rotating.
NOTES:
● Digital Dubbing is performed in the sound mode recorded on the original tape, regardless of the current “SOUND
MODE” setting (੬ pg. 33).
● During Digital Dubbing, no signals are output from the video or audio connectors.
40EN
USING THE OPTIONAL REMOTE CONTROL UNIT
The Full-Function Remote Control Unit can operate
this camcorder from a distance as well as the basic
operations (Playback, Stop, Pause, Fast-Forward and
Rewind) of your VCR. It also makes additional
playback functions possible.
A
1
2
3
Installing The Battery
(RM-V700U, optional)
1
1
Lock hole
The remote control uses one lithium battery
(CR2025).
B
1There are 2 ways to pull the battery holder out of
the RM-V700U.
: Pull out the battery holder while sliding the lock
hole.
2
: Pinch the release tab and pull out the battery
holder.
3
2
Insert the battery in the holder, and be sure to
have the “+” mark visible.
Knob
1
3
Slide the holder back in until you hear a click.
• Read the caution concerning lithium batteries in the
RM-V700U instruction manual.
Remote sensor
When using the remote control, be sure to point it
at the remote sensor. The transmitted beam’s
approximate effective distance for indoor use is
5m (16ft).
The transmitted beam may not be effective or
may cause incorrect operation outdoors or when
the remote sensor is directly exposed to sunlight
or powerful lighting.
EN 41
1
3
9
!
0
@
2
4
5
7
#
%
6
8
$
^
&
RM-V700U
(optional)
Functions
Buttons
With the camcorder’s Power Switch set to With the camcorder’s Power Switch
the camera position (
“
” or “
”).
set to “PLAY”.
1 PAUSE IN Connector*
—
—
—
2 MBR SET Button*
3 INT. TIME Button*
SELF TIMER Button*
4 REC TIME Button*
—
ANIM. Button*
5 FF Button
—
—
Forward, Forward Shuttle Search
(੬ pg. 19)
6 REW Button
Rewind, Reverse Shuttle Search
(੬ pg. 19)
7 PAUSE Button
—
—
Pause (੬ pg. 19)
8 PLAY Button
Playback start (੬ pg. 19)
9 Infrared beam
Transmits the beam signal.
transmitting window
0 START/STOP Button
! VISS Button*
Functions the same as the Recording Start/Stop Button on the camcorder.
—
@ ZOOM (T/W) Buttons
# VCR CTL Button*
$ A.DUB Button
Zoom in/out (੬ pg. 17)
Zoom in/out (੬ pg. 42)
—
—
—
—
—
੬ pg. 43
% STOP Button
Stops (੬ pg. 19)
੬ pg. 44
^ INSERT Button
& R.A.EDIT Buttons*
* This function is unavailable with this camcorder.
42EN
USING THE OPTIONAL REMOTE CONTROL UNIT (cont.)
Remote sensor
FEATURE: Playback Zoom
PURPOSE:
To magnify the recorded image up to 70X at any
time during playback.
OPERATION:
1) Press PLAY (4) to find the scene of interest.
2) Press the Zoom Buttons (T/W) on the remote
control. Make sure the remote control is pointed
at the camcorder's remote sensor. Pressing T
zooms in.
Ⅲ To end zoom, press and hold W until
magnification returns to normal. Or, press STOP
(5) and then press PLAY (4).
NOTES:
● Zoom can also be used during still playback.
● Due to ditital image processing, the quality of the
image may suffer.
RM-V700U
(optional)
Zoom Buttons
STOP
PLAY
Normal playback
Press T
EN 43
Display
Audio Dubbing
Audio Dub Standby
mode
The audio track can be customized only when
recorded in the 12-bit mode (੬ pg. 33).
6e
NOTES:
● Audio Dubbing is not possible on a tape recorded in 16-
bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.
● To perform Audio Dubbing while watching on the
television, make connections (੬ pg. 20).
1
Play back the tape to locate the point where
editing will start, then press PAUSE (6).
Speaker
Power Switch
2
While holding A.DUB (e) on the remote control,
press PAUSE (6). “6e” appears.
3
Press PLAY (4) , then begin “narrating”.
Speak into the microphone.
• To pause dubbing, press PAUSE (6).
4
To end Audio Dubbing, press PAUSE (6), then
STOP (5).
To hear the dubbed sound during playback . . .
..... set “12BIT MODE” to “SOUND 2” or “MIX” in the
Menu Screen (੬ pg. 36, 37).
NOTES:
Remote sensor
Stereo
● Sound is not heard from the speaker during Audio
Dubbing.
microphone
● When editing onto a tape that was recorded at 12-bit,
the old and new soundtracks are recorded separately.
● If you dub onto a blank space on the tape, the sound
may be disrupted. Make sure you only edit recorded
areas.
● If feedback or howling occurs during TV playback,
move the camcorder’s microphone away from the TV,
or turn down the TV’s volume.
● If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.
● During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit
audio or a blank portion, Audio Dubbing stops
(੬ pg. 62).
RM-V700U
(optional)
A.DUB
STOP
PAUSE
PLAY
44EN
USING THE OPTIONAL REMOTE CONTROL UNIT (cont.)
Insert Editing
You can record a new scene into a previously
recorded tape, replacing a section of the original
recording with minimal picture distortion at the in and
outpoints. The original audio remains unchanged.
NOTES:
● Before performing the following steps, make sure that
“TIME CODE” is set to “ON” in the Menu Screen
(੬ pg. 35, 37).
● Insert Editing is not possible on a tape recorded in the
LP mode or on a blank portion of a tape.
● To perform Insert Editing while watching in the
television, make connections (੬ pg. 20).
Lock Button
Power Switch
1
Play back the tape, locate the Edit-Out point and
press PAUSE (6). Confirm the time code at this point
(੬ pg. 35, 37).
Display
2
Press REW (2) until the Edit-In point is located,
then press PAUSE (6).
w
6
3
Press and hold INSERT (w) on the remote
control, then press PAUSE (6). “6w” and the Time
Code (min.:sec.) appear and the camcorder enters
Insert-Pause mode.
12 : 34
4
Press START/STOP to begin editing.
• Confirm the insert at the time code you checked in
step 1.
Remote sensor
• To pause editing, press START/STOP. Press it
again to resume editing.
5
To end Insert Editing, press START/STOP, then
STOP (5).
NOTES:
● Program AE with special effects (੬ pg. 24, 25) can be
used to spice up the scenes being edited during Insert
Editing.
● During Insert Editing, the date and time information
changes.
● If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.
● During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert
Edting stops (੬ pg. 62).
START/STOP
REW
PAUSE
PLAY
STOP
INSERT
RM-V700U
(optional)
EN 45
SYSTEM CONNECTIONS
Power Switch
Core filter
Core filter
To DV
DV cable (optional)
To DV
IN/OUT
connector
PC with DV
connector
NOTES:
Connection To A Personal Computer
● It is recommended to use the AC Adapter as the
power supply instead of the battery pack (੬ pg. 9).
● The date/time information cannot be captured into the
PC.
This camcorder can transfer still images to a PC with
a DV connector by using software equipped with the
PC or commercially available software.
● Refer to the instruction manuals of the PC and
Software.
1
2 Make sure the camcorder and PC are turned off.
Connect the camcorder to your PC using the
● The still images can also be transferred to a PC with a
DV connector-equipped capture board.
● When using a DV cable, be sure to use the optional
JVC VC-VDV206U or VC-VDV204U DV cable
depending on the type of DV connector (4 or 6 pins)
on the PC, or use the DV cable provided with the
capture board.
appropriate cable as shown in the illustration.
3
Turn the camcorder’s Power Switch to “PLAY”
while pressing down the Lock Button located on the
switch and turn on the PC.
• Refer to the instruction manual of the software on
how to transfer a still image to the PC.
● The system may not work properly depending on the
PC or capture board you are using.
4
When finished, turn off the PC first, then the
camcorder.
46EN
REFERENCES
REFERENCES
CONTENTS
DETAILS ............................................ 47
TROUBLESHOOTING ....................... 48 – 52
USER MAINTENANCE ............................. 53
CAUTIONS .................................. 54 – 56
SPECIFICATIONS .................................. 57
INDEX ....................................... 58 – 62
Controls, Connectors And Indicators ....... 58 – 59
Indications ................................... 60 – 62
TERMS ........................ 63 – Back Cover
EN 47
DETAILS
I T E M S
❍ Power
N O T E S
❍ Perform charging where the temperature is between 10°C and 35°C (50°F
and 95°F). 20°C to 25°C (68°F to 77°F) is the ideal temperature range for
charging. If the environment is too cold, charging may be incomplete.
(੬ pg. 8)
❍ Charging times are for a fully discharged battery pack.
❍ Charging time varies according to the ambient temperature and the status of
the battery pack.
❍ To avoid interference with reception, do not use the AC Adapter near a radio.
❍ Since the AC Adapter processes electricity internally, it becomes warm
during use. Be sure to use it only in well-ventilated areas.
❍ The following operation stops charging:
• Set the Power Switch to “PLAY”, “ ” or “ ”.
• Disconnect the AC adapter from the camcorder.
• Unplug the AC adapter from the AC outlet.
• Detach the battery from the camcorder.
❍ When you use the LCD monitor outdoors in direct sunlight, the LCD monitor
may be difficult to see. If this happens, use the viewfinder instead.
❍ RECORDING
(੬ pg. 15, 16)
❍ The cassette holder cannot be opened unless a power supply is attached.
❍ There may be a delay after you open the cassette holder cover until the
cassette holder opens. Do not use force.
❍ Once the cassette holder is closed, it recedes automatically. Wait until it
recedes completely before closing the cassette holder cover.
❍ When the Recording Start/Stop button is pressed, it may take a few seconds
before actual recording starts. “
” starts rotating when the camcorder
actually starts recording.
❍ The time required to calculate and display the remaining tape length, and the
accuracy of the calculation, may vary according to the type of tape used.
❍ “TAPE END” appears when the tape reaches its end, and the power goes off
automatically if left in this condition for 5 minutes. “TAPE END” also appears
when a cassette at its end is loaded.
48 EN
TROUBLESHOOTING
If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio,
etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery
pack, AC Adapter, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the
beginning.
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
1 No power is supplied.
• The power is not connected
properly.
• The battery is dead.
• Connect the AC Adapter securely
(੬ pg. 9).
• Replace the dead battery with a
fully charged one (੬ pg. 8, 9).
2 “SET DATE/TIME!”
• The date/time is not set.
• Set the date/time (੬ pg. 11).
• Consult your nearest JVC dealer
for replacement.
appears.
• The built-in clock battery has run
out and the previously set date/time
has been erased.
3 Recording cannot be
• The tape’s erase protection tab is
set to “SAVE”.
• The Power Switch is set to “PLAY”
or “OFF”.
• “TAPE END” appears.
• The cassette holder cover is open.
• Set the tape’s erase protection tab
to “REC” (੬ pg. 12).
performed.
• Set the Power Switch to “ ” or
“
” (੬ pg. 16).
• Replace with new cassette
(੬ pg. 12).
• Close the cassette holder cover.
4 There is no picture.
• The camcorder is not getting
power, or some other malfunction
exists.
• Turn the camcorder’s power off
and on again (੬ pg. 16).
5 The focus does not adjust
• Focus is set to the Manual mode.
• The recording was done in a dark
place, or the contrast was low.
• The lens is dirty or covered with
condensation.
• Set Focus to the Auto mode
(੬ pg. 29).
• Clean the lens and check the focus
again (੬ pg. 53).
automatically.
6 The cassette will not load
• The cassette is in the wrong
position.
• The battery’s charge is low.
• Set it in the right position
(੬ pg. 12).
• Install a fully charged battery
(੬ pg. 8, 9).
properly.
7 Snapshot mode cannot be
• The Squeeze mode is selected.
• Disengage the Squeeze mode
(੬ pg. 34).
used.
EN 49
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
8 The color of Snapshot looks • The light source or the subject does • Find a white subject and compose
strange.
not include white. Or there are
various different light sources
behind the subject.
• The Sepia or Monotone mode is
activated.
your shot so that it also appears in
the frame (੬ pg. 28).
• Turn off Sepia and Monotone
(੬ pg. 24, 25).
9 The image taken using
• Shooting was performed under
backlit conditions.
• Press the BACKLIGHT Button
(੬ pg. 30).
Snapshot is too dark.
0 The image taken using
• The subject is too bright.
• Set “PROGRAM AE” to
“SPOTLIGHT” in the Menu Screen
(੬ pg. 24).
Snapshot is too bright.
! Digital Zoom does not work. • 16X optical zoom is selected.
• Set “ZOOM” to “40X” or “700X” in
the Menu Screen (੬ pg. 33).
@ The Black & White Fader
• The Sepia or Monotone mode is
activated.
• Turn off Sepia and Monotone
(੬ pg. 24, 26).
does not work.
# Even when Slow Shutter is
not selected, the image
• When shooting in the dark, the unit • If you want the lighting to look
becomes highly sensitive to light
and the image takes on an effect
similar to Slow Shutter.
more natural, set GAIN UP to
“AGC” or “OFF” in the Menu
Screen (੬ pg. 33).
looks like it is activated.
$ White Balance cannot be
• The Sepia or Monotone mode is
activated.
• Turn off Sepia or Monotone before
setting White Balance (੬ pg. 25,
31).
activated.
% When shooting a subject
illuminated by bright light,
vertical lines appear.
• This is a result of exceedingly high
contrast, and is not a malfunction.
————
^ When the screen is under
direct sunlight during
shooting, the screen
becomes red or black for an
instant.
• This is not a malfunction.
————
CONTINUED ON NEXT PAGE
50 EN
TROUBLESHOOTING (cont.)
CORRECTIVE ACTION
SYMPTOM
POSSIBLE CAUSES
& During recording, the date/
• “DATE/TIME” is set to “OFF” in the
Menu Screen.
• Set “DATE/TIME” to “ON” in the
Menu Screen (੬ pg. 35).
time does not appear.
* Time code does not appear. • “TIME CODE” is set to “OFF” in the • Set “TIME CODE” to “ON” in the
Menu Screen.
Menu Screen (੬ pg. 35, 36).
( Images on the LCD monitor • In places subject to low tempera-
• Adjust the brightness and angle of
the LCD monitor (੬ pg. 15, 16).
appear dark or whitish.
ture, images become dark due to
the characteristics of the LCD
monitor. When this happens, the
displayed colors differ from those
that are actually recorded. This is
not a defect of the camcorder.
• When the LCD monitor's fluores-
cent light reaches the end of its
service life, images on the LCD
monitor become dark. Consult your
nearest JVC dealer.
) The rear of the LCD monitor • The light used to illuminate the LCD • Close the LCD monitor to turn it off
is hot.
monitor causes it to become hot.
or set the Power Switch to “OFF”,
and let the unit cool down.
q The indicators and the
image color on the LCD
monitor are not clear.
• This may occur when the surface or
the edge of the LCD monitor is
pressed.
————
w The LCD monitor or
• Certain Fade/Wipe effects, certain
modes of Program AE with special
effects, “DIS” and other functions
that cannot be used together are
selected at the same time.
• Re-read the sections covering
Fade/Wipe effects, Program AE
with special effects and “DIS”
(੬ pg. 24 – 27, 33).
viewfinder indications blink.
EN 51
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
e Colored bright spots appear • The LCD monitor and the view-
all over the LCD monitor or
the viewfinder.
finder are made with high-precision
technology. However, black spots
or bright spots of light (red, green
or blue) may appear constantly on
the LCD monitor or the viewfinder.
These spots are not recorded on
the tape. This is not due to any
defect of the unit. (Effective dots:
more than 99.99 %)
————
r During recording, sound
• This is normal.
————
cannot be heard.
t Play, Rewind and Fast-
Forward functions do not
work.
• The Power Switch is set to “ ” or
• Set the Power Switch to “PLAY”
(੬ pg. 19).
“
”.
y The LCD monitor image is
• During playback of the unrecorded
portion, High-speed Search and still
playback, LCD monitor indications
appear distorted. This is not a
defect.
distorted.
————
u Images on the LCD monitor • The speaker volume is too great.
• Turn the speaker volume down
(੬ pg. 19).
are jittery.
i Blocks of noise appear
• Clean the video heads with an
optional cleaning cassette
(੬ pg. 55).
during playback, or there is
————
no playback picture and the
screen becomes blue.
CONTINUED ON NEXT PAGE
52 EN
TROUBLESHOOTING (cont.)
CORRECTIVE ACTION
SYMPTOM
POSSIBLE CAUSES
o The LCD monitor, the
viewfinder and the lens
have become dirty (ex.
fingerprints).
• Wipe them gently with soft cloth.
Wiping strongly can cause damage
(੬ pg. 53).
————
p An unusual mark appears.
• Check the section of the manual
that explains LCD monitor/
viewfinder indications
————
(੬ pg. 60 – 62).
Q An error indication
• A malfunction of some kind has
occurred. In this case the
camcorder’s functions become
unusable.
• Remove the power supply (battery
pack, etc.) and wait a few minutes
for the indication to clear. When it
does, you can resume using the
camcorder. If the indication
(E01, E02 or E06) appears.
remains even though you repeat
the above two or three times,
please consult your nearest JVC
dealer. Do not eject the cassette.
This will cause damage to the tape.
W An error indication
• A malfunction of some kind has
occurred. In this case the
camcorder’s functions become
unusable.
• Eject the cassette once and re-
insert it, then check if the indication
clears. When it does, you can
resume using the camcorder. If the
indication remains even though you
repeat the above two or three
times, please consult your nearest
JVC dealer.
(E03 or E04) appears.
E The charger indicator on
the camcorder does not
light.
• The temperature of the battery is
extremely high/low.
• Charging is difficult in places
subject to extremely high/low
temperatures.
• To protect the battery, it is
recommended to charge it in
places with a temperature of 10°C
to 35°C (50°F to 95°F) (੬ pg. 54).
R When the image is printed
from the printer, a black bar
appears at the bottom of
the screen.
• This is not a malfunction.
• By recording with “DIS” activated
(੬ pg. 33) this can be avoided.
T When the camcorder is
connected via the DV
connector, the camcorder
does not operate.
• The DV cable was plugged/
unplugged with power turned on.
• Turn the camcorder’s power off and
on again, then operate it.
EN 53
USER MAINTENANCE
After Use
Cleaning The Camcorder
1
1
To clean the exterior, wipe gently with a soft cloth.
Put the cloth in diluted mild soap and wring it well to
wipe off heavy dirt. Then wipe again with a dry cloth.
2 Turn off the camcorder.
Slide and hold OPEN/EJECT in the direction of
the arrow, then pull the cassette holder cover open
until it locks. The cassette holder opens automatically.
Remove the cassette.
2
Press PUSH OPEN and open the LCD monitor.
Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
3
Press “PUSH HERE” to close the cassette holder.
• Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely before
closing the cassette holder cover.
3
To clean the lens, blow it with a blower brush,
then wipe gently with lens cleaning paper.
4
To clean the viewfinder, raise it to the vertical
4
Tilt the viewfinder upward 1. Press BAT.
position. Open the viewfinder cleaning hatch in the
RELEASE 2 and remove the battery pack 3 .
direction of the arrow 1.
5
Insert a lens blower or soft cloth into the gap at
the bottom of the viewfinder and clean the interior of
the viewfinder with it 2.
6
Close the hatch. Tilt the viewfinder back to the
horizontal position.
NOTES:
Remove.
● Avoid using strong cleaning agents such as benzine or
alcohol.
Cassette
holder
PUSH HERE
● Cleaning should be done only after the battery pack
has been removed or other power units have been
disconnected.
● Mold may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth refer
to the cautions of each product.
Cassette holder
cover
OPEN/EJECT Switch
BAT. RELEASE Button
1
2
Hatch
Lens blower
1
2
3
54 EN
CAUTIONS
When using the AC Adapter in areas other than
the USA
NOTES:
● It is normal for the battery pack to be warm after
charging, or after use.
Ⅲ The provided AC Adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
Temperature Range Specifications
Charging ................ 10°C to 35°C (50°F to 95°F)
Operation ............... 0°C to 40°C (32°F to 104°F)
Storage................... –10°C to 30°C (14°F to 86°F)
● Recharging time is based on room temperature of 20°C
(68°F).
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an AC
wall outlet other than American National Standard
C73 series type use an AC plug adapter, called a
“Siemens Plug”, as shown.
● The lower the temperature, the longer recharging takes.
For this AC plug adapter, consult your nearest JVC
dealer.
Cassettes
To properly use and store your cassettes, be sure to
read the following cautions:
Plug adapter
1. During use . . .
... make sure the cassette bears the Mini DV mark.
... be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
... make sure the cassette is positioned properly
when inserting.
... do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage.
... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
Battery Packs
The supplied battery pack is
a lithium-ion battery. Before
using the supplied battery
pack or an optional battery
pack, be sure to read the
following cautions:
Terminals
1. To avoid hazards . . .
... do not burn.
2. Store cassettes . . .
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
... do not short-circuit the terminals. When
transporting, make sure the provided battery cap
is attached to the battery. If the battery cap is
misplaced, carry the battery in a plastic bag.
... do not modify or disassemble.
... do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
... use only specified chargers.
... vertically, in their original cases.
2. To prevent damage and prolong service life . . .
... do not subject to unnecessary shock.
... charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type battery—
cooler temperatures impede chemical reaction,
while warmer temperatures can prevent
complete charging.
... store in a cool, dry place. Extended exposure to
high temperatures will increase natural
discharge and shorten service life.
... fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period time.
... remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
EN 55
4. To protect the unit, DO NOT . . .
LCD Monitor
1. To prevent damage to the LCD monitor,
DO NOT . . .
... push it strongly or apply any shocks.
... place the camcorder with the LCD monitor on
the bottom.
2. To prolong service life . . .
... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for LCD
monitor use.
These are not malfunctions:
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration during
transportation.
... keep the lens directed at extremely bright
objects for long periods.
... expose the lens to direct sunlight.
... carry it by holding the LCD monitor or the
viewfinder.
... swing it excessively when using the shoulder
strap or the grip.
5. Dirty heads can cause the following problems:
• While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
• If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
Main Unit
1. For safety, DO NOT . . .
... open the camcorder’s chassis.
... disassemble or modify the unit.
... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
... allow inflammables, water or metallic objects to
enter the unit.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
camcorder is not in use.
• No picture during playback.
• Blocks of noise appear during playback.
• During recording or playback, the Head Clog
Warning indicator “ ” appears.
• Recording cannot be performed properly.
In such cases, use an optional cleaning cassette.
Insert it and play back. If the cassette is used more
than once consecutively, damage to the video
heads may result. After the camcorder plays back
for about 20 seconds, it stops automatically. Also
refer to the cleaning cassette’s instructions.
If, after using the cleaning cassette, the problems
still exist, consult your nearest JVC dealer.
Mechanical moving parts used to move the video
heads and video tape tend to become dirty and
worn out over time. In order to maintain a clear
picture at all times, periodic check-ups are
recommended after using the unit for about 1,000
hours. For periodic check-ups please consult your
nearest JVC dealer.
2. Avoid using the unit . . .
... in places subject to excessive humidity or dust.
... in places subject to soot or steam such as near
a cooking stove.
... in places subject to excessive shock or
vibration.
... near a television set.
... near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
... in places subject to extremely high (over 40°C or
104°F) or extremely low (under 0°C or 32°F)
temperatures.
3. DO NOT leave the unit . . .
... in places of over 50°C (122°F).
... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
... in direct sunlight.
... in a closed car in summer.
... near a heater.
56 EN
CAUTIONS (cont.)
About moisture condensation . . .
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form
on the glass‘ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a place
directly subjected to the cool air from an air
conditioner.
Change or modifications not approved by the
party responsible for compliance could void the
user’s authority to operate the equipment. This
equipment has been tested and found to comply
with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment gener-
ates, uses, and can radiate radio frequency
energy and, if not installed and used in accord-
ance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equip-
ment and receiver.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
The camcorder is a microcomputer-controlled
device. External noise and interference (from a
TV, a radio, etc.) might prevent it from functioning
properly. In such cases, first disconnect its power
supply unit (battery pack, AC Adapter, etc.) and
wait a few minutes and then re-connect it and
proceed as usual from the beginning.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
EN 57
SPECIFICATIONS
Camcorder
General
Power supply
: DC 11.0 V
DC 7.2 V
(Using AC Adapter)
(Using battery pack)
Power consumption
LCD monitor off, viewfinder on
LCD monitor on, viewfinder off
Dimensions (W x H x D)
: Approx. 4.3 W
: Approx. 5.3 W
: 83 mm x 94 mm x 223 mm (3-5/16" x 3-3/4" x 8-13/16")
(with the LCD monitor closed and the viewfinder pushed down)
: Approx. 630 g (1.4 lbs)
Weight
Operating temperature
Operating humidity
Storage temperature
Pickup
: 0°C to 40°C (32°F to 104°F)
: 35% to 80%
: –20°C to 50°C (–4°F to 122°F)
: 1/4" CCD
Lens
: F 1.6, f = 3.9 mm to 62.4 mm, 16:1 power zoom lens
: ø40.5 mm
: 2.5" diagonally measured, LCD panel/TFT active matrix system
: Electronic viewfinder with 0.24" black/white LCD
: Monaural
Filter diameter
LCD monitor
Viewfinder
Speaker
Digital Video Camera
Format
: DV format (SD mode)
Signal format
: NTSC standard
Recording/Playback format
: Video: Digital component recording
: Audio: PCM digital recording, 32 kHz 4-channel (12-bit),
48 kHz 2-channel (16-bit)
Cassette
: Mini DV cassette
Tape speed
: SP: 18.8 mm/s
LP: 12.5 mm/s
Maximum recording time
(using 80 min. cassette)
: SP: 80 min.
LP: 120 min.
Connectors
S-Video
Output
: Y: 1 V (p-p), 75 Ω, analog
C: 0.29 V (p-p), 75 Ω, analog
AV
Video output
Audio output
DV
: 1 V (p-p), 75 Ω, analog
: 300 mV (rms), 1 kΩ, analog, stereo
Output
Input
: 4-pin, IEEE 1394 compliant
: 4-pin, IEEE 1394 compliant
AC Adapter
Power requirement
U.S.A. and Canada
Other countries
Output
: AC 120 V`, 60 Hz
: AC 110 V to 240 V`, 50 Hz/60 Hz
: DC 11 V
, 1 A
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject to
change without notice.
58 EN
INDEX Controls, Connectors And Indicators
& ^
)
e
w
1
u
2
3 4 5 6 7
q
@ # $
r
y
t
8 9 0 !
Q W
%
i
o
p
( *
EN 59
Controls
Indicators
1 Monitor Open Button [PUSH OPEN] ...... ੬ pg. 15
) CHARGE Lamp ........................................ ੬ pg. 8
2 Diopter Adjustment Control .................... ੬ pg. 10
q Power Lamp ..................................... ੬ pg. 15, 16
3 Battery Release Button
[BAT. RELEASE] ...................................... ੬ pg. 8
Other Parts
4 • MENU Wheel [+, –, PUSH] .................. ੬ pg. 32
• LCD Monitor BRIGHT (Brightness)
w Stereo Microphone ................................. ੬ pg. 43
e Viewfinder............................................... ੬ pg. 10
r Viewfinder Cleaning Hatch ..................... ੬ pg. 53
t Shoulder Strap Eyelets .......................... ੬ pg. 10
y Grip Strap ............................................... ੬ pg. 10
u • Remote Sensor .................................... ੬ pg. 40
Control [+, –] ........................................ ੬ pg. 15
5 Snapshot Button
[SNAPSHOT] ......................................... ੬ pg. 28
6 • Power Zoom Lever [T/W] ..................... ੬ pg. 17
• Speaker Volume Control [VOL.] ........... ੬ pg. 19
• Camera Sensor
7 • FOCUS Button ..................................... ੬ pg. 29
Be careful not to cover this area, a sensor
necessary for shooting is built-in here.
• BLANK SEARCH Button...................... ੬ pg. 22
8 • Stop Button [5] .................................... ੬ pg. 19
• BACKLIGHT Button ............................. ੬ pg. 30
i LCD Monitor ..................................... ੬ pg. 15, 16
o Speaker .................................................. ੬ pg. 19
p Battery Pack Mount .................................. ੬ pg. 8
Q Stud Hole ............................................... ੬ pg. 10
W Tripod Mounting Socket ......................... ੬ pg. 10
9 • Rewind Button [2] ............................. ੬ pg. 19
• NIGHT ALIVE Button ........................... ੬ pg. 24
0 Play/Pause Button [4/6]........................ ੬ pg. 19
! Fast-Forward Button [3] ...................... ੬ pg. 19
@ Power Switch
[
,
, PLAY, OFF] .............................. ੬ pg. 16
# Recording Start/Stop Button .................. ੬ pg. 15
$ Lock Button ............................................ ੬ pg. 16
% OPEN/EJECT Switch ............................. ੬ pg. 12
Connectors
The connectors ^ to * are located beneath a cover.
^ Audio/Video Output Connector
[AV] ................................................... ੬ pg. 20, 38
& S-Video Output Connector
[S-VIDEO] ........................................ ੬ pg. 20, 38
* DC Input Connector ............................. ੬ pg. 8, 9
( Digital Video Connector
[DV IN/OUT] (i.Link*) ........................ ੬ pg. 39, 45
* i.Link refers to the IEEE1394-1995 industry
specification and extensions thereof.
The logo is used for products compliant with
the i.Link standard.
60 EN
INDEX Indications
LCD Monitor/Viewfinder Indications During Recording
8 9 0
!
@ # $
LP 50min
REC
1
2
40x W
T
%
^
w
6
3
4
5
3
&
*
6
BR I GHT
JAN 10 ’ 02
10 : 00 AM
15 : 55
7
q
)
(
1 Appears when the Power Switch is set to “ ”.
(੬ pg. 16)
: Appears when Night-Alive is engaged.
(੬ pg. 24)
: Appears when “GAIN UP” is set to
“AUTO” and the shutter speed is being
automatically adjusted. (੬ pg. 33)
3 Appears when the white balance is adjusted.
(੬ pg. 31)
4 • “ؓ”:Appears when the exposure is adjusted.
(੬ pg. 30)
: Appears when backlight compensation is
used. (੬ pg. 30)
! Appears when in the Squeeze or Cinema mode.
(੬ pg. 34)
2 •
@ Rotates while the tape is running.
# Displays the recording mode (SP or LP).
(੬ pg. 13)
(੬ pg. 15)
(੬ pg. 15)
•
$ Displays the tape remaining time.
% • “REC” appears during recording.
• “PAUSE” appears during Record-Standby
mode.
(੬ pg. 15)
• “PHOTO” appears when taking a Snapshot.
(੬ pg. 28)
•
^ Appears when the Insert Editing (w) or Insert
Editing Pause (6w) mode is engaged.(੬ pg. 44)
5 Displays the selected Program AE with special
& Appears when the wind cut mode is engaged to
effects.
(੬ pg. 24)
(੬ pg. 30)
cut down on noise created by wind. (੬ pg. 34)
6 Appears when the iris is locked.
* • BRIGHT : Displays the brightness of the LCD
monitor.
(੬ pg. 15)
7 Appears when Digital Image Stabilizer (“DIS”) is
• SOUND : Displays the sound mode for approx.
engaged. (੬ pg. 33)
5 seconds after turning on the
8 Approximate zoom ratio: Appears during
camcorder.
(੬ pg. 33)
zooming.
(੬ pg. 17)
( Displays the date/time.
(੬ pg. 11)
9 Appears during zooming.
Zoom level indicator
) Appears when the focus is adjusted manually.
(੬ pg. 29)
(੬ pg. 18, 35)
(੬ pg. 17)
0 Displays the selected Fade/Wipe effect.
(੬ pg. 26, 27)
q Displays the Time Code.
EN 61
LCD Monitor/Viewfinder Indications During Playback
1 Displays the sound mode.
2 Displays the Blank Search mode.
(੬ pg. 36, 37)
(੬ pg. 22)
1
2
3
4
3 Displays the tape speed.
(੬ pg. 13)
4 Appears while a tape is running.
4
: Playback
12B I T
L
/
SOUND
1
SP
4
6
3
2
6
: Fast-Forward/Shuttle search
: Rewind/Shuttle search
: Pause
6
1
e
4
: Forward slow-motion
: Reverse slow-motion
: Audio Dubbing
BLANK SEARCH
VOLUME
6
6e : Audio Dubbing Pause
5 Displays the date/time.
6 • BRIGHT : Displays the brightness of the
(੬ pg. 36, 37)
DEC 25 ’ 02
116 : 21 : 25
10 : 00 AM
LCD monitor.
(੬ pg. 15)
• VOLUME : Displays the speaker
volume.
The level indicator moves.
(੬ pg. 19)
7
6
5
7 Displays the time code.
(੬ pg. 36, 37)
62 EN
Warning Indications
INDEX Indications (cont.)
Indications
Function
Displays the battery remaining power.
Remaining power level: high
Remaining power level: exhausted
As the battery power comes close to nil, the battery indicator
blinks.
(੬ pg. 12)
When the battery power is exhausted, power turns off automatically.
Appears when no tape is loaded.
Appears when the erase protection tab is set to “SAVE” while the Power
CHECK TAPE’S ERASE
PROTECTION TAB
Switch is set to “ ” or “ ”.
(੬ pg. 12)
Appears if dirt is detected on the heads during recording or playback.
Use an optional cleaning cassette.
(੬ pg. 55)
HEAD CLEANING
REQUIRED USE
CLEANING CASSETTE
Appears if condensation occurs. When this indication is displayed, wait more
than 1 hour until condensation disappears.
CONDENSATION
OPERATION PAUSED
PLEASE WAIT
Appears if a tape is not loaded when the Recording Start/Stop Button or
SNAPSHOT Button is pressed while the Power Switch is set to “ ” or
TAPE!
“
”.
Appears when the tape ends during recording or playback.
Appears if a tape in another format is loaded.
(੬ pg. 47)
TAPE END
DIFFERENT
FORMATTED TAPE
● Appears when the date/time is not set.
(੬ pg. 11)
● Appears when the built-in clock battery runs out and the previously set
SET DATE/TIME!
date/time is erased. Consult your nearest JVC dealer for replacement.
Appears for 5 seconds after power is turned on if the lens cap is attached.
LENS COVER
Appears if Audio Dubbing is attempted on a blank portion of a tape.
A. DUB ERROR!
(੬ pg. 43)
● Appears if Audio Dubbing is attempted on a tape recorded in the LP mode.
(੬ pg. 43)
A. DUB ERROR!
<CANNOT DUB
● Appears if Audio Dubbing is attempted on a tape recorded in 16-bit audio.
(੬ pg. 43)
ON A LP RECORDED TAPE>
<CANNOT DUB
● Appears if A. DUB (e) on the remote control is pressed when the erase
ON A 16BIT
RECORDING>
<CHECK TAPE’S ERASE
PROTECTION TAB>
protection tab is set to “SAVE”.
(੬ pg. 43)
Appears if Insert Editing is attempted on a blank portion of a tape.
INSERT ERROR!
(੬ pg. 44)
● Appears if Insert Editing is attempted on a tape recorded in the LP mode.
(੬ pg. 44)
INSERT ERROR!
<CANNOT EDIT
ON A LP RECORDED TAPE>
<CHECK TAPE’S ERASE
PROTECTION TAB>
● Appears if INSERT (w) on the remote control is pressed when the erase
protection tab is set to “SAVE”.
(੬ pg. 44)
The error indications (E01, E02 or E06) show what type of malfunction has
occured. When an error indication appears, the camcorder turns off
automatically. Remove the power supply (battery, etc.) and wait a few
minutes for the indication to clear. When it does, you can resume using the
camcorder. If the indication remains, consult your nearest JVC dealer.
E01, E02 or E06
UNIT IN SAFEGUARD
MODE REMOVE AND
REATTACH BATTERY
The error indications (E03 or E04) show what type of malfunction has
occured. When an error indication appears, the camcorder turns off
automatically. Eject the cassette once and re-insert it, then check if the
indication clears. When it does, you can resume using the camcorder. If the
indication remains, consult your nearest JVC dealer.
E03 or E04
UNIT IN SAFEGUARD
MODE EJECT AND
REINSERT TAPE
EN 63
Terms
A
I
AC Adapter................................................ ੬ pg. 8, 9
Audio Dubbing ............................................ ੬ pg. 43
Auto Date .................................................... ੬ pg. 35
Auto Focus .................................................. ੬ pg. 29
Auto Shut off ......................................... ੬ pg. 15, 19
Icons ................................................... ੬ pg. 33 – 35
Insert Editing ............................................... ੬ pg. 44
Iris ............................................................... ੬ pg. 30
Iris Lock ....................................................... ੬ pg. 30
J
B
Journalistic Shooting ................................... ੬ pg. 16
Backlight Compensation ............................. ੬ pg. 30
Battery Low ................................................. ੬ pg. 62
Battery Pack ........................................ ੬ pg. 8, 9, 54
Beep............................................................ ੬ pg. 34
Blank Search............................................... ੬ pg. 22
Brighten The LCD Monitor .......................... ੬ pg. 15
L
LCD monitor/Viewfinder Indications .... ੬ pg. 60 – 62
Load A Tape ................................................ ੬ pg. 12
M
Manual Focus ............................................. ੬ pg. 29
Menu Screen, CAMERA ............................. ੬ pg. 33
Menu Screen, DISPLAY ........................ ੬ pg. 35, 36
Menu Screen, MANUAL........................ ੬ pg. 33, 34
Menu Screen, SYSTEM ...................... ੬ pg. 34 – 36
Menu Screen, VIDEO ................................. ੬ pg. 36
Monotone .................................................... ੬ pg. 25
Motor Drive Mode ....................................... ੬ pg. 28
C
Channels (Left/Right) .................................. ੬ pg. 37
Charge The Battery Pack .............................. ੬ pg. 8
Cinema ........................................................ ੬ pg. 34
Classic Film................................................. ੬ pg. 25
Clean The Camcorder ................................. ੬ pg. 53
Connections ...................... ੬ pg. 8, 9, 20, 21, 38, 45
N
D
Night-Alive................................................... ੬ pg. 24
Darken The LCD Monitor ............................ ੬ pg. 15
Date/Time Display ............................... ੬ pg. 35 – 37
Date/Time Settings...................................... ੬ pg. 11
Demonstration Mode ............................... ੬ pg. 6, 35
Digital Zoom .......................................... ੬ pg. 17, 33
DIS (Digital Image Stabilizer) ...................... ੬ pg. 33
Diopter Adjustment...................................... ੬ pg. 10
Dubbing................................................. ੬ pg. 38, 39
P
Playback Zoom ........................................... ੬ pg. 42
Power Switch Position ................................ ੬ pg. 16
Program AE With Special Effects .......... ੬ pg. 24, 25
Provided Accessories.................................... ੬ pg. 5
R
Record-Standby .......................................... ੬ pg. 15
Recording Mode.......................................... ੬ pg. 13
Remote Control ........................................... ੬ pg. 40
Reset........................................................... ੬ pg. 35
Rewind The Tape ........................................ ੬ pg. 19
E
Erase Protection ......................................... ੬ pg. 12
Exposure Control ........................................ ੬ pg. 30
F
Fade-In/Out ........................................... ੬ pg. 26, 27
Fast-Forward The Tape ............................... ੬ pg. 19
Frame-By-Frame Playback ......................... ੬ pg. 19
CONTINUED ON NEXT PAGE
G
Gain Up ....................................................... ੬ pg. 33
Grip Adjustment .......................................... ੬ pg. 10
S
T
Self-Recording ............................................ ੬ pg. 16
Sepia ........................................................... ੬ pg. 25
Set Remote Control/VCR Code .................. ੬ pg. 43
Shuttle Search ............................................ ੬ pg. 19
Shutter Speed ............................................. ੬ pg. 25
Slow Shutter ................................................ ੬ pg. 25
Snapshot ..................................................... ੬ pg. 28
Snapshot Mode ........................................... ੬ pg. 28
Snow ........................................................... ੬ pg. 25
Sound Mode .................................... ੬ pg. 33, 36, 37
Speaker Volume .......................................... ੬ pg. 19
Specifications ........................................ ੬ pg. 60, 61
Sports .......................................................... ੬ pg. 25
Spotlight ...................................................... ੬ pg. 25
Squeeze ...................................................... ੬ pg. 34
Still Playback............................................... ੬ pg. 19
Strobe ......................................................... ੬ pg. 25
Tally ............................................................. ੬ pg. 34
Tele Macro .................................................. ੬ pg. 34
Time Code..................................... ੬ pg. 18, 35 – 37
Tripod Mounting .......................................... ੬ pg. 10
Twilight ........................................................ ੬ pg. 25
U
Unload A Tape ............................................. ੬ pg. 12
W
W
White Balance ............................................. ੬ pg. 31
Wide Mode .................................................. ੬ pg. 34
Wind Cut ..................................................... ੬ pg. 34
Wipe In/Out ........................................... ੬ pg. 26, 27
Z
Zooming ...................................................... ੬ pg. 17
See previous page as well.
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Japan
0202HOV*UN*SN
U
COPYRIGHT© 2002 VICTOR COMPANY OF JAPAN, LTD.
|