EN
INSTRUCTIONS
HD HARD DISK CAMCORDER
GZ-HD7U
Dear Customer
Thank you for purchasing
this hard disk camera. Before
use, please read the safety
information and precautions
contained in pages 4 and 5 to
ensure safe use of this product.
For Future Reference:
Enter the Model No. (located on
the bottom of the camera) and
Serial No. (located on the battery
pack mount of the camera)
below.
Model No.
Serial No.
Back Up High-Definition Images
on DVD Discs!
Video can easily be backed up on a DVD disc by connecting to
a separate DVD burner (CU-VD40/CU-VD20). (੬ pg. 47)
This DVD disc can then be played in the camera or a PC, but
not in a DVD player.
•
If a CU-VD40 is used, the DVD burner can be connected
directly to a television so the disc can be played without using
the camera.
•
Edit High-Definition Images on
a PC!
Perform advanced editing on high-definition images by loading
to a PC.
8 For PC models that can be connected
See page 53 or 64.
3
Safety Precautions
When the equipment is installed in a cabinet or on
a shelf, make sure that it has sufficient space on
all sides to allow for ventilation (10 cm (3-15/16")
or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
The apparatus shall not be exposed to dripping
or splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
WARNING:TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
NOTES:
The rating plate and safety caution are on the
bottom and/or the back of the main unit.
•
Do not point the lens directly into the sun. This
can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a
risk of fire or electric shock.
The serial number plate is on the battery pack
mount.
•
The rating information and safety caution of the
AC adapter are on its upper and lower sides.
•
CAUTION!
The following notes concern possible physical
damage to the camera and to the user.
Carrying or holding the camera by the LCD monitor
can result in dropping the unit, or in a malfunction.
Do not use a tripod on unsteady or unlevel surfaces.
It could tip over, causing serious damage to the
camera.
Caution on Replaceable lithium battery
The battery used in this device may present a fire
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
or incinerate.
Replace battery with Panasonic (Matsushita
Electric), Sanyo, Sony or Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.)
to the camera and leaving it on top of the TV is
not recommended, as tripping on the cables will
cause the camera to fall, resulting in damage.
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose of in
fire.
•
•
•
CAUTION:
For USA-California Only
The mains plug shall remain readily operable.
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material
– special handling may apply.
WARNING:
Batteries shall not be exposed to excessive heat
such as direct sunshine, fire or the like.
4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
Remember that this camera is intended for
private consumer use only.
Any commercial use without proper permission
is prohibited. (Even if you record an event such
as a show, performance or exhibition for personal
enjoyment, it is strongly recommended that you
obtain permission beforehand.)
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
Trademarks
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
i.LINK is a trademark of Sony
Corp.
•
HDMI is a trademark of HDMI
•
Licensing, LLC.
Windows® is either registered trademark or
•
trademark of Microsoft Corporation in the United
States and/or other countries.
9. Only use attachments/accessories specified by
the manufacturer.
10.Use only with the cart,
stand, tripod, bracket,
or table specified by
Macintosh is a registered trademark of Apple
Computer, Inc.
Other product and company names included
in this instruction manual are trademarks
and/or registered trademarks of their respective
holders.
•
•
the manufacturer,
or sold with the
apparatus. When a cart
is used, use caution
when moving the
cart/apparatus combination to avoid injury from
tip-over.
11.Unplug this apparatus during lightning storms
or when unused for long periods of time.
12.Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
5
JVC Software License Agreement
4 LIMITED WARRANTY
JVC SOFTWARE LICENSE AGREEMENT
JVC warrants that any media in which the
Program is embodied are free from any defects
in materials and workmanship for a period of
thirty (30) days from the date of Your purchasing
any our products accompanying the Program.
JVC’s entire liability and your exclusive remedy
in connection with the Program shall be
replacement of such defective media. EXCEPT
FOR THE EXPRESS WARRANTIES STATED
HEREIN AND TO THE EXTENT PERMITTED BY
APPLICABLE LAW, JVC AND ITS LICENSORS
DISCLAIM ANY OTHER WARRANTIES, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN REGARD TO
THE PROGRAM AND THE ACCOMPANYING
PRINTED MATERIALS. SHOULD THERE BE
ANY PROBLEM ARISING FROM OR CAUSED
BY THE PROGRAM, YOU SHOULD SETTLE
ALL SUCH PROBLEM AT YOUR OWN COST
AND EXPENSE.
IMPORTANT
TO CUSTOMERS: PLEASE MAKE SURE TO
READ THIS CAREFULLY BEFORE INSTALLING
OR USING THE SOFTWARE PROGRAM
NAMED “DIGITAL PHOTO NAVIGATOR”
(“Program”) ON YOUR PC.
The right to use the Program is granted by Victor
Company of Japan, Limited (“JVC”) to You only
on the condition that You agree to the following.
Should You not agree to the terms hereof, You
may not install or use the Program. HOWEVER,
INSTALLING OR USING THE PROGRAM
INDICATES YOUR ACCEPTANCE OF THESE
TERMS AND CONDITIONS.
1 COPYRIGHT; OWNERSHIP
You acknowledge that all copyrights and other
intellectual property rights in the Program are
owned by JVC and its licensor, and remain
vested in JVC and such licensor. The Program is
protected under the copyright law of Japan and
other countries, and related Conventions.
2 GRANT OF LICENSE
5 LIMITED LIABILITY
TO THE EXTENT PERMITTED BY APPLICABLE
LAW, IN NO EVENT SHALL JVC AND ITS
LICENSORS BE LIABLE FOR ANY INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES WHATSOEVER, REGARDLESS
OF THE FORM OF ACTION WHETHER IN
CONTRACT, TORT OR OTHERWISE ARISING
OUT OF OR IN CONNECTION WITH THE USE
OF OR INABILITY TO USE THE PROGRAM,
EVEN IF JVC HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.YOU
WILL INDEMNIFY AND HOLD HARMLESS
JVC FROM ANY LOSS, LIABILITY OR
(1)
Subject to the conditions of this Agreement,
JVC grants to You a non-exclusive right to
use the Program.You may install and use the
Program on a HDD or other storage devices
incorporated in Your PC.
(2)
You may make one (1) copy of the Program
solely for your personal backup or archival
purposes.
3 RESTRICTION ON THE PROGRAM
(1) You may not reverse engineer, decompile,
disassemble, revise or modify the Program,
except to the extent that expressly permitted
by applicable law.
(2) You may not copy or use the Program, in
whole or in part, other than as expressly
specified in this Agreement.
COST ARISING OUT OF OR IN ANY WAY
CONNECTED TO CLAIMS FROM ANY THIRD
PARTY RELATING TO THE USE OF THE
PROGRAM.
(3) You have no right to grant a license to use
the Program, and may not distribute, rent,
lease or transfer the Program to any third
party or otherwise let them use the Program.
6
NOTE
6 TERM
If You acquired the Program in Germany, the
provisions of Sections 4 (Limited Warranty)
and 5 (Limited Liability) provided above will be
replaced with those of the German version of this
Agreement.
This Agreement will become effective on the date
when You install and use the Program on Your
machine, and continue to be in effect until the
termination under the following provision.
Should You breach any provision of this
Agreement, JVC may terminate this Agreement
without giving any notice to You. In this event,
JVC may claim against You for any damages
caused by Your breach. Should this Agreement
be terminated, You must immediately destroy the
Program stored in Your machine (including the
erasing from any memory in Your PC), and no
longer own such Program.
CAUTION:
Operate this equipment according to the
operating procedures described in this manual.
•
Use only the provided CD-ROM. Never use any
other CD-ROM to run this software.
•
Do not attempt to modify this software.
Changes or modifications not approved by
JVC could void user’s authority to operate the
equipment.
•
•
7 EXPORT CONTROL
You agree that You will not ship, transfer or
export the Program or underlying information
and technology to any countries to which Japan
and other relevant countries have initiated an
embargo on such goods.
How to handle a CD-ROM
Take care not to soil or scratch the mirror
•
surface (opposite to the printed surface). Do
not write anything or put a sticker on either
the front or back surface. If the CD-ROM
gets dirty, gently wipe it with a soft cloth
outward from the center hole.
8 U.S. GOVERNMENT USER
If You are an agency of the United States of
America (the “Government”), You acknowledge
JVC’s representation that the Program is
a “Commercial Item” as defined in Federal
Acquisition Regulation (FAR) part 2.101 (g)
consisting unpublished “Commercial Computer
Software” as those items are used at FAR part
12.212 and is only licensed to You with the same
use rights JVC grants all commercial end users
pursuant to the terms of this Agreement.
Do not use conventional disc cleaners or
cleaning spray.
•
Do not bend the CD-ROM or touch its mirror
surface.
•
Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
•
9 GENERAL
(1) No modification, change, addition, deletion
or other alternation of or to this Agreement
will be valid unless reduced to writing and
signed by an authorized representative of
JVC.
You can find the latest information (in
English) on the provided software program
jvc-victor.co.jp/english/global-e.html
(2) If any part of this Agreement is held
invalid by or in conflict with any law having
jurisdiction over this Agreement, the
remaining provisions will remain in full force
and effect.
(3) This Agreement shall be governed by and
interpreted under the laws of Japan. The
Tokyo District Court has jurisdiction over all
disputes which may arise with respect to the
execution, interpretation and performance of
this Agreement.
Victor Company of Japan, Limited
7
Contents
GETTING STARTED
PLAYBACK
Accessories .......................................... 10
Playing Back Files................................ 30
Attaching/Detaching the Lens Hood............10
Attaching the Shoulder Strap.......................11
Preparing the Remote Control.....................11
Index ...................................................... 12
Indications on LCD Monitor................. 14
Necessary Settings before Use........... 16
Charging the Battery Pack...........................16
Language Setting ........................................17
Date/Time Setting........................................17
Other Settings....................................... 18
Video Playback ...........................................30
Still Image Playback ...................................31
File Search Function....................................32
To Play Back TPD Files ...............................33
Playback with Special Effects......................34
Watching Images on TV........................ 36
Connection with TV......................................36
Playback Operation .....................................37
EDITING/PRINTING
Grip Adjustment...........................................18
Lens Cover ..................................................18
Checking the Remaining Battery Power......18
Tripod Mounting...........................................18
When Using an SD Card .............................19
Managing Files...................................... 38
Deleting/Protecting Files..............................38
Viewing File Information ..............................40
Changing the Event Registration of Video
Files after Recording ...................................41
To Extract a Still Image File From a Video File ...42
DPOF Print Setting......................................42
Playlists................................................. 44
Creating Playlists ........................................44
Playing Back Playlists..................................45
Other Operations of Playlists.......................46
RECORDING
Recording Files..................................... 20
Video Recording..........................................20
Still Image Recording ..................................21
Zooming.......................................................22
Record Using the Viewfinder .......................22
Registering Files to Events..........................23
Checking the Remaining Space on the
COPYING
Recording Media .........................................23
Manual Recording ............................... 24
Copying Files........................................ 47
Using a DVD Burner to Copy Files from the
Camera........................................................47
Using a VCR/DVD Recorder to Dub Files from
the Camera..................................................50
Copying/Moving Still Image Files.................52
To Change to Manual Recording Mode.......24
Program AE.................................................24
Aperture Priority Setting..............................25
Changing the Shutter Speed .......................25
Adjust Brightness.........................................26
Manual Focus..............................................26
Nightalive.....................................................27
Backlight Compensation..............................27
Spot Exposure Control ................................27
Manual Setting in Function Menu................28
8
PC OPERATION
Read This First!
File Backup on the PC – Windows® .... 53
8 Make a backup of important
recorded data
System Requirements .................................53
Software Installation ....................................54
Connecting the Camera to the PC...............56
File Backup on the PC.................................57
File Backup on the PC without Using
Software ......................................................58
Other PC Operations – Windows® ...... 59
Playing back Files on the PC.......................59
Creating Discs/Editing Files.........................60
Getting More Use from the Software...........62
File Backup on the PC – Macintosh ... 64
System Requirements .................................64
Software Installation ....................................64
Connecting the Camera to the PC...............65
File Backup on the PC.................................66
JVC will not be responsible for any
lost data. It is recommended to copy
your important recorded data to a DVD
or other recording media for storage.
(੬ pg. 47)
8 Make a trial recording
Before the actual recording of important
data, make a trial recording and play
back the recorded data to check that the
video and sound have been recorded
correctly.
8 Reset the camera if it does not
operate correctly
This camera uses a microcomputer.
Factors such as background noise and
interference can prevent it from operating
correctly. If the camera does not operate
correctly, reset the camera. (੬ pg. 74)
8 Precautions on handling batteries
FURTHER INFORMATION
Be sure to use the JVC BN-VF815U/
•
VF823U battery packs.
Changing the Menu Settings............... 67
Folder Structure and Extensions........ 73
Troubleshooting.................................... 74
Warning Indications ............................. 78
Cleaning ................................................ 79
Specifications ....................................... 80
Cautions ................................................ 82
Terms..................................................... 84
If the camera is subjected to
electrostatic discharge, turn the power
off before using it again.
•
8 If a malfunction occurs, stop
using the camera immediately and
consult your local JVC dealer
If a problem occurs when using the SD
•
card, take the card together with the
camera for repair. If one of them is not
included, the cause of the malfunction
cannot be diagnosed, and the camera
cannot be repaired.
Recorded data may be erased while
•
the camera is being repaired or
inspected. Back up all data before
requesting repairs or inspections.
8 Because the camera may be used
for demonstration in a shop, the
demonstration mode is set to on by
default
To deactivate the demonstration mode,
set [DEMO MODE] to [OFF]. (੬ pg. 70)
9
GETTING STARTED
Accessories
AC Adapter
AP-V14U
Battery Pack
BN-VF815U
Component Cable
Audio/Video Cable
(੬ pg. 37, 51)
(੬ pg. 36)
USB Cable
(੬ pg. 47, 56, 65)
Lens Hood
Already attached to
the camera.
Shoulder Strap
(੬ pg. 11)
CD-ROM
(੬ pg. 54, 64)
(੬ below)
Remote Control Unit
RM-V750U (੬ pg. 11)
Lithium Battery
CR2025
Pre-installed in the
remote control unit.
NOTE
Make sure to use the provided cables for connections. Do not use any other cables.
Attaching/Detaching the Lens Hood
Place the protrusion in
the groove.
Protrusion
10
Attaching the Shoulder Strap
Peel off the pad and thread
the end of the strap through
the eyelet.
Thread the strap through the
Position the buckle near the
eyelet and reattach the pad.
buckle, adjust its length, and
use the strap guide to fix it
in place.
Buckle
Strap Guide
Eyelet
Preparing the Remote Control
A battery is included inside the remote control at the time of purchase.
Remove the insulation sheet before use.
Beam Effective Area
To Reinsert the Battery
Pull out the battery holder by pressing the
lock tab.
Remote Sensor
Lock Tab
Lithium Battery
(CR2025)
Effective distance:
5 m (16 ft)
NOTE
The transmitted beam may not be effective
or may cause incorrect operation when the
remote sensor is directly exposed to sunlight
or powerful lighting.
11
Index
NOTES
The LCD monitor can rotate 270°.
•
Power-linked operation
•
You can also turn the camera on/off by
opening/closing the LCD monitor during the
recording mode.
Be careful not to cover C, Dand Kduring
shooting.
•
12
9 Video Recording Start/Stop Button [REC]
(੬ pg. 20)
Camera
: Grip Strap (੬ pg. 18)
! Index Button [INDEX] (੬ pg. 32)/
Remaining Space Button/Data Battery
Button [ 0/1] (੬ pg. 18, 23)
# Set Lever
; Battery Pack Mount (੬ pg. 16)
< i.LINK Connector [ i ] (੬ pg. 50)
= HDMI Connector [HDMI] (੬ pg. 36)
> USB (Universal Serial Bus) Connector [
]
2
Move to ¡:
(੬ pg. 47, 56, 65)
Reverse Skip (੬ pg. 30)/Up
Move to ¢:
? DC Input Connector [DC] (੬ pg. 16)
@ Lock Button (੬ pg. 16)
A Power/Mode Switch [OFF (CHARGE),
STANDBY/ON, MODE] (੬ pg. 16)
B Shoe
C Camera Sensor
Remote Sensor (੬ pg. 11)
D Stereo Microphone
Forward Skip (੬ pg. 30)/Down
Move to £:
Reverse Search (੬ pg. 30)/Left/
Nightalive [NIGHT] (੬ pg. 27)
Move to ¤:
Forward Search (੬ pg. 30)/Right/
Program AE [PROGRAM AE] (੬ pg. 24)
Press down:
E Focus Ring (੬ pg. 26)
F Lens Hood (੬ pg. 10)
G Microphone Input Connector [MIC]
Play/Pause (੬ pg. 30)
$ Playback/Recording Mode Switching
Button [SELECT PLAY/REC] (੬ pg. 20)
% Auto/Manual Mode Button [AUTO/
MANUAL] (੬ pg. 24)
H Audio/Video Connector [AV] (੬ pg. 37, 51)
I Lens Cover Switch [ ] (੬ pg. 18)
,
=>
J Tally Lamp (੬ pg. 70)
K Lens
& Backlight Compensation Button/
Spot Exposure Control Button [BACK
LIGHT] (੬ pg. 27)
( Information Button [INFO] (੬ pg. 40)
) Aperture Priority Setting Button [A]
(੬ pg. 25)
L Lens Cover (੬ pg. 18)
M Stud Hole (੬ pg. 18)
N Tripod Mounting Socket (੬ pg. 18)
O SD Card Slot (੬ pg. 19)
[ Manual Focus Button [FOCUS] (੬ pg. 26)
\ Focus Assist Button [FOCUS ASSIST]
(੬ pg. 26)
* Function Button [FUNCTION] (੬ pg. 28)
+ LCD Monitor
, Direct Backup Button [DIRECT BACK
UP] (੬ pg. 57)/Event Button [EVENT]
(੬ pg. 23)
Remote Control
- S Connector [S] (੬ pg. 37, 51)
. Speaker (੬ pg. 30)
/ Component Connector [COMPONENT]
(੬ pg. 36)
0 Menu Button [MENU] (੬ pg. 17)
1 Value Adjustment Lever [M-MENU]
(੬ pg. 25)
2 Brightness Button [BRIGHT] (੬ pg. 26)
3 Shutter Speed Button [S] (੬ pg. 25)
4 Viewfinder (੬ pg. 22)
5 Battery Release Button [BATT.] (੬ pg. 16)
6 Access/Charge Lamp [ACCESS/CHARGE]
(੬ pg. 16)
(Blinks when you access files or charge the
battery. Do not turn off the power or remove the
battery pack/AC adapter while accessing files.)
Video/Still Image Mode Lamp [ !, #]
(੬ pg. 20, 21)
Q Infrared Beam Transmitting Window
R ZOOM (T/W) Buttons
Zoom In/Out
S Up Button
Rotate Button (counterclockwise)
(੬
pg. 31)
T Skip Backward Button
U Left Button
V Back Button
W PLAYLIST Button (੬ pg. 44)
X START/STOP Button
Y SNAPSHOT Button (੬ pg. 21)
Z INFO Button (੬ pg. 40)
a Skip Forward Button
b PLAY/PAUSE Button
c Right Button
d Next Button
e Down Button
Rotate Button (clockwise) (੬ pg. 31)
f INDEX Button
g DATE Button
7 Still Image Shooting Button [SNAPSHOT]
(੬ pg. 21)
8 Zoom Lever [W 7,T ] (੬ pg. 22)
,
Speaker Volume Control [–VOL+]
(੬ pg. 30)
13
Indications on LCD Monitor
During both Video and Still Image
Recording
During Video Recording Only
[ 4 h 5 9 m ]
0 : 0 4 : 0 1
REC
0
2 0 0 X
W
T
F 5 . 6
1/4000
FOCUS
4 : 5 5 PM
! Mode Indicator (੬ pg. 20)
JAN. 20. 2007
# Wind Cut Indicator (੬ pg. 68)
$ Picture Quality (੬ pg. 68)
% Remaining Time (੬ pg. 20, 81)
& Counter (੬ pg. 68)
! Selected Recording Mode Indicator
(੬ pg. 24)
# Tele Macro Mode Indicator (੬ pg. 29)
$ Approximate Zoom Ratio (੬ pg. 22)
% Inhibit Indicator
& Zoom Indicator (੬ pg. 22)
( Focus Assist Indicator (੬ pg. 26)
) Shutter Speed (੬ pg. 25)
* Brightness/Sharpness Control Indicator
(੬ pg. 29, 70)
+ Battery Indicator (੬ pg. 78)
, Date/Time (੬ pg. 17)
( 7REC : (Appears during recording.)
(੬ pg. 20)
79 : (Appears during record-standby
mode.)
)
External Microphone Input Level Indicator
(੬ pg. 68)
* Event Indicator (੬ pg. 23)
+ Optical Image Stabilizer (OIS) Indicator
(Appears when [OIS] is set to [OFF].)
(੬ pg. 68)
- Manual Focus Adjustment Indicator
(੬ pg. 26)
. Selected Recording Medium Indicator
(੬ pg. 68, 69)
During Still Image Recording Only
/ Drop Detection Indicator (Appears when
[DROP DETECTION] is set to [OFF].)
(੬ pg. 70)
1920
[ 9 9 9 9 ]
FINE
0 Effect Mode Indicator (੬ pg. 29)
1 Program AE Mode Indicator (੬ pg. 24)/
5: Nightalive Indicator (੬ pg. 27)
2 White Balance Indicator (੬ pg. 28)
3 Aperture Value (F-number) (੬ pg. 25)
PHOTO
10
! Mode Indicator (੬ pg. 21)
# ISO Sensitivity
4
0 : Exposure Adjustment Indicator
(੬ pg. 26)
(GAIN): When set to [AUTO], there is no
indication. (੬ pg. 69)
-: Backlight Compensation Indicator
$ Focus Indicator (੬ pg. 21)
% Image Size (੬ pg. 69)
(੬ pg. 27)
.: Spot Exposure Control Indicator
(੬ pg. 27)
& Picture Quality (੬ pg. 69)
( Remaining Number of Shots (੬ pg. 81)
) {: Continuous Shooting Mode Indicator
(੬ pg. 69)
5 Iris Lock Indicator (੬ pg. 27)
J: Bracket Shooting Mode Indicator
(੬ pg. 69)
* Shooting Indicator (੬ pg. 21)
+ Self-Timer Recording Indicator (੬ pg. 69)
14
During Video Playback
During Still Image Playback
X - 6 0
1 : 5 5 : 0 1
1 0 1 - 0 0 9 8
4 : 5 5 PM
JAN. 20. 2007
4 : 5 5
PM
JAN. 20. 2007
! Mode Indicator (੬ pg. 30)
: Playlist Playback Indicator (Appears
! Mode Indicator (੬ pg. 31)
#
# Folder/File Number
6
when playing back a playlist.) (੬ pg. 45)
¨ª: Event Search Playback Indicator
(Appears when playing back a video file
from the event search.) (੬ pg. 33)
¨©: Date Search Playback Indicator
(Appears when playing back a video file
from the date search.) (੬ pg. 32)
$ Slide Show Playback Indicator (੬ pg. 31)
% Battery Indicator (੬ pg. 78)
& Date/Time (੬ pg. 70)
( Selected Medium Indicator (੬ pg. 68, 69)
) Drop Detection Indicator (Appears when
[DROP DETECTION] is set to [OFF].)
(੬ pg. 70)
$ Picture Quality (੬ pg. 68)
% Playback Mode (੬ pg. 30)
U : Playback
* Effect Mode Indicator (੬ pg. 34)
9 : Pause
5
: Forward Search
: Reverse Search
3
9U : Forward Slow-Motion
Y9 : Reverse Slow-Motion
(The number on the left shows speed.)
& Counter (੬ pg. 68)
Operation guide display
The operation guide is displayed at the
bottom of the screen during menu display
etc.
( Volume Level Indicator
) Battery Indicator (੬ pg. 78)
* Date/Time (੬ pg. 70)
+ Selected Medium Indicator (੬ pg. 68, 69)
, Drop Detection Indicator (Appears when
[DROP DETECTION] is set to [OFF].)
(੬ pg. 70)
- Effect Mode Indicator (੬ pg. 34)
. Wipe/Fader Effect Indicator (੬ pg. 35)
SELECT SET
QUIT
15
Necessary Settings before Use
3 Connect the AC adapter.
Power/Mode
Switch
Access/Charge
Lamp
DC Connector
AC Adapter
To AC Outlet
(110V to 240V)
Set Lever
The access/charge lamp blinks to
indicate charging has started.
When the lamp goes out, charging is
finished. Unplug the AC adapter from the
AC outlet and disconnect the AC adapter
from the camera.
•
•
Be sure to configure the following three
settings before use.
Charging the Battery Pack
Required charging / recording time
(approx.)
1 Set the power/mode switch to OFF.
Recording
Slide while pressing down the lock button.
Battery pack Charging time
time
BN-VF815U
2 hr. 40 min.
(Provided)
1 hr. 20 min.
(1hr. 25 min.*)
OFF
(CHARGE)
2 hr. 00 min.
(2 hr. 10 min.*)
BN-VF823U 3 hr. 50 min.
2 Attach the battery pack.
* When using the viewfinder.
Slide the battery pack down until it locks
in place.
8 To detach the battery pack
Slide and hold BATT. (੬ step 2), then
remove the battery pack.
BATT.
8 To check the remaining battery power
See page 18.
NOTES
You can also use the camera with just the
AC adapter.
•
Please do not pull or bend the AC adapter
plug and cable. This may damage the AC
adapter.
•
16
Date/Time Setting
Language Setting
After performing steps 1-4 (੬ left column)
The language on the display can be changed.
5 Select [CLOCK ADJUST].
1 Set the power/mode switch to
STANDBY/ON.
CLOCK ADJUST
Select
DATE
TIME
Slide while pressing down the lock button.
JAN 31 2007 11 07 AM
STANDBY/ON
Set
SELECT SET
QUIT
6 Set the date and time.
Select
2
VIDEO
SCENE COUNTER
EXTERNAL MIC LEVEL
MENU
QUALITY
ZOOM
OIS
Set
SELECT SET
QUIT
Repeat this step to input the month, day,
year, hour and minute.
3
VIDEO
SCENE COUNTER
EXTERNAL MIC LEVEL
QUALITY
ZOOM
OIS
8 To return to the previous screen
Move the set lever to £.
SELECT SET
QUIT
8 To exit the screen
Press MENU.
4 Select [GENERAL].
GENERAL
Select
DISPLAY
DISPLAY ON TV
LANGUAGE
CLOCK ADJUST
You have now finished configuring the
necessary settings.
DATE DISPLAY STYLE
8 To use the camera right away
See page 20.
Set
SELECT SET
QUIT
8 To configure other settings
See page 18.
5 Select [LANGUAGE].
LANGUAGE
Select
Set
ENGLISH
SELECT SET
QUIT
6 Select the desired language.
Select
Set
8 To return to the previous screen
Move the set lever to £.
8 To exit the screen
Press MENU.
17
Other Settings
Checking the Remaining Battery
Power
Power/Mode
Switch
Preparation:
Set the power/mode switch to OFF.
Attach the battery pack.
•
•
BATTERY CONDITION
100%
MAX TIME
LCD MONITOR
min
50%
0%
FINDER
min
INDEX
Battery information is displayed for approx. 3
seconds if the button is pressed and released
quickly, and for approx. 15 seconds if the
button is pressed and held for several seconds.
Lens Cover
Switch
NOTES
If “COMMUNICATING ERROR” appears,
•
there may be a problem with your battery.
In such a case, consult your nearest JVC
dealer.
Grip Adjustment
The recordable time display should only be
used as a guide. It is displayed in 10 minute
units.
•
Open the pad and make grip adjustments.
Tripod Mounting
Align the camera stud hole with the tripod
stud, and the mounting socket with the screw,
and then rotate the camera clockwise to
mount it to the tripod.
Bottom of the Camera
Lens Cover
When not using the camera, close the lens
cover to protect the lens.
Open the lens cover
Close the lens cover
NOTE
Do not push the lens cover strongly. Doing so
may cause damage to the lens.
NOTE
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camera.
18
3 Close the SD card cover.
When Using an SD Card
If you want to record to an SD card, the
following three operations need to be
performed.
8 To remove an SD card
Push the SD card once.
After the card comes out a little, pull it out.
Operations are guaranteed on the following
SD cards.
•
NOTES
Video recording: Class 6 compatible SDHC
card
Still image recording: Panasonic, TOSHIBA,
SanDisk, ATP (128MB to 4 GB) or SDHC
card (4GB)
Insert and remove the SD card only while
the power is turned off. Otherwise, data on
the card may be corrupted.
•
Do not touch the terminal on the reverse
side of the label.
•
If other media are used, they may fail to
record data correctly, or they may lose data
that had already been recorded.
•
RChange the recording medium
MultiMediaCards are not supported.
Files in full high-definition picture quality
cannot be recorded on an SD card.
•
The camera is programmed to record on the
built-in hard disk when it is shipped from the
factory.You can change the recording medium
to SD card.
•
Cards used to record video on this camera
cannot be played back on other devices.
•
Set [REC MEDIA FOR VIDEO] and
[REC MEDIA FOR IMAGE] to [SD].
(੬ pg. 68, 69)
QInsert an SD card
Preparation:
Set the power/mode switch to OFF.
NOTE
1 Open the SD card cover.
Video picture quality (੬ pg. 68) will
automatically be set to [SP].
SFormat an SD card when using it for
the first time
This will also ensure stable speeds and
operation when accessing the SD card.
Select [EXECUTE] in [FORMAT SD
CARD] to format the card. (੬ pg. 72)
Bottom of the
Camera
2 Firmly insert the card with its clipped
edge first.
Clipped Edge
19
RECORDING
Recording Files
Video Recording
Preparation: Set the power/mode switch to STANDBY/ON.
Slide the power/mode switch to
Press the PLAY/REC button to
MODE to select
(video) mode.
select recording mode.
!
MODE
The switch returns
to the original
position when it is
released.
SELECT
PLAY/REC
The
lamp on the camera lights up.
!
Press the REC button to start
recording.
REC
[ 4 h 5 9 m ]
REC
Approximate remaining time for
recording appears.
8 To stop recording
Press the REC button again.
8 To change the picture quality
Change the settings in [QUALITY].
(੬ pg. 68)
8 To register a file to an event
See page 23.
NOTES
The video recording mode is automatically selected when you turn the camera’s power off and
then on again.
If the camera is not operated for 5 minutes while the power is on, it turns itself off automatically
to conserve power. To turn the camera on again when using the battery pack, set the
power/mode switch to OFF, then to STANDBY/ON. When using the AC adapter, perform any
operation such as zooming.
•
•
Video files are given the names MOV001.TOD to MOV009.TOD, MOV00A.TOD to
MOV00F.TOD, and MOV010.TOD in order of recording.
•
A new file will be created for every 4 GB or approx. 19 minutes of continuous shooting.
This camera records video in MPEG2 format compliant with SD-VIDEO format.
Do not move or shake the camera suddenly during recording. If you do so, the sound of the
hard disk drive may be recorded.
•
•
•
20
Still Image Recording
Preparation: Set the power/mode switch to STANDBY/ON.
Slide the power/mode switch to
Press the PLAY/REC button to
select recording mode.
MODE to select
mode.
(still image)
#
19
MODE
The switch returns
to the original
position when it is
released.
SELECT
PLAY/REC
The
lamp on the camera lights up.
#
Press and hold the SNAPSHOT
button halfway.
1920
[
FINE
The ?indicator becomes green when
the captured image is focused.
8 To change the picture quality
Change the settings in [QUALITY].
(੬ pg. 69)
Press the SNAPSHOT button to
start recording.
8 To record still images continuously
Set [CONTINUOUS SHOOTING] to
[ON]. (੬ pg. 69)
20
[ 9 9 9 9 ]
FINE
PHOTO
8 To change the image size
Change the settings in [IMAGE SIZE].
(੬ pg. 69)
NOTES
If the camera is not operated for 5 minutes while the power is on, it turns itself off automatically
to conserve power. To turn the camera on again when using the battery pack, set the
power/mode switch to OFF, then to STANDBY/ON. When using the AC adapter, perform any
operation such as zooming.
•
The sides of still images recorded in 16:9 size may be cut off when printed. Check whether
16:9 size prints can be printed at your local print store.
•
21
Recording Files (Continued)
Record Using the Viewfinder
Power/Mode Switch
Zoom Lever
Recording by using the viewfinder is
recommended in bright environments where
the LCD monitor is difficult to see or to
increase recording time on battery.
Preparation:
Slide the power/mode switch to MODE to
•
select
or
mode.
! #
Press the PLAY/REC button to select
•
recording mode.
1 Close the LCD monitor.
PLAY/REC
Button
2 Extend the viewfinder.
DIRECT
BACKUP/
EVENT
Set Lever
Zooming
Preparation:
Slide the power/mode switch to MODE to
•
select
or
mode.
! #
Press the PLAY/REC button to select
•
recording mode.
3 Adjust the view using the control bar.
Zoom out
Zoom in
W: Wide angle
T: Telephoto
Maximum zoom ratio is 10X (factory-preset).
8 To change the maximum zoom ratio (for
!mode only)
NOTE
If the LCD monitor is opened while using
the viewfinder, the picture will move to the
LCD monitor and will not be displayed in
the viewfinder. To set the viewfinder as
priority when recording, set the [PRIORITY
SETTING] to [FINDER]. (੬ pg. 71)
Change the settings in [ZOOM]. (੬ pg. 68)
NOTE
Macro shooting is possible as close as
approx. 5 cm (2") to the subject when the
zoom lever is set all the way to W.
22
Registering Files to Events
Checking the Remaining Space on
– !mode only
the Recording Media – !mode only
If you select an event to register the file to
before starting recording, the file will be
registered to the selected event, thus making
the file easy to find at playback. There are up
to 3 different destinations within each event
(for example: BABY1, BABY2, BABY3).
Preparation:
Slide the power/mode switch to MODE to
•
select
mode.
!
Press the PLAY/REC button to select
•
recording mode.
MAX RECORDING TIME
HDD
F
Preparation:
5h00m
7h00m
4h56m
Slide the power/mode switch to MODE to
1
•
C
FREE
USED
select
mode.
!
INDEX
Press the PLAY/REC button to select
•
recording mode.
The maximum recording time is displayed for
each picture quality mode.
1
CHANGE EVENT REG.
ON/SELECT
OFF
DIRECT
BACKUP
8 To return to the normal screen
/EVENT
Press the 0button again.
2 Select [ON/SELECT].
Select
VACATION
1/ 3
NON SECTION
SELECT SET
NEXT PAGE
QUIT
Set
3 Select the event that you want to
register the file to.
To select a different destination, select
[NEXT PAGE].
•
To cancel the event registration, select
[NON SECTION].
•
Select
Set
The selected event is displayed on the screen.
Press the REC button to start recording.
8 To exit the screen
Press EVENT.
8 To search by event for a file to play back
See page 32.
NOTE
Once you select to register a file to a certain event,
the setting will remain even if you turn the power off.
Unless you change the setting, you will register a file
to the same event that you had previously selected.
23
Manual Recording
Program AE
Power/Mode
Switch
Focus Ring
You can record videos or still images with
optimum brightness by adjusting the exposure
and shutter speed to suit your surroundings or
the subject.
AUTO/MANUAL
BACK LIGHT
Set Lever
After performing “To Change to Manual
Recording Mode” (੬ left column)
1
OFF
PLAY/REC
Button
BRIGHT
2 Select the desired setting.
For details on each setting, see below.
Select
A
S
M
-MENU
FUNCTION
FOCUS
FOCUS
ASSIST
Set
8 To cancel the program AE
Select [OFF] in step 2.
Manual recording mode enables you to set
the focus and screen brightness etc. manually.
You need to switch to this mode because auto
recording mode, which adjusts these settings
automatically, is selected by default.
8 Items for program AE setting
6PORTRAIT:
•
The subject in the foreground is
accentuated by blurring the background.
HSPORTS:
•
•
Records fast moving subjects clearly.
GSNOW:
To Change to Manual Recording
Mode
Compensates for subjects that may
appear too dark when shooting in
extremely bright surroundings, such as
in snow.
Preparation:
Slide the power/mode switch to MODE to
•
/SPOTLIGHT:
select
or
mode.
! #
•
•
Select this when a spotlight makes a
subject appear too bright.
Press the PLAY/REC button to select
•
recording mode.
TWILIGHT:
I
Press twice.
Makes evening scenes look more natural.
8 To return to the auto recording mode
Press the AUTO/MANUAL button so that
the 4indicator appears.
24
Aperture Priority Setting
Changing the Shutter Speed
You can add a blurring effect to the background
by setting the aperture value (F-number).
A fast shutter speed can freeze the motion
of a fast-moving subject, and a slow shutter
speed can blur the subject to give the
impression of motion.
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
1
A
1
S
F 1 . 8
1 / 6 0
2 Select the desired setting. (F1.8 to
F8.0)
The lower the F-number (larger aperture
value), the more blurred the background
will become. The higher the F-number
(smaller aperture value), the clearer the
focus will be for both near and far objects.
2 Select the desired setting (1/2 to
1/4000 in !mode, 1/2 to 1/500 in #
mode).
The smaller the value, the faster the
shutter speed.
M
MENU
M
MENU
Select
Set
Select
Set
8 To cancel the aperture priority setting
Press the A button so that the value
indicator disappears.
8 To cancel the shutter speed setting
Press the S button so that the value
indicator disappears.
NOTE
NOTE
If the image is too bright, set to a larger
F-number. If the image is too dark, set to a
smaller F-number.
It is recommended to use the tripod (੬ pg. 18)
when recording with a slow shutter speed.
25
Manual Recording (Continued)
Adjust Brightness
Manual Focus
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
1
1
FOCUS
BRIGHT
0
4 :
JAN. 2
2 Select the desired setting. (–6 to +6
in !mode, –2.0EV to +2.0EV in #
mode)
2 Slide the focus ring to adjust the
focus.
M
MENU
Select
Set
8 To lock the exposure
After you finish configuring the setting,
press and hold the set lever for more than 2
seconds. The indicator appears.
C
8 To cancel the manual focus setting
Press the FOCUS button so that the @/A
indicator disappears.
8 To cancel the brightness setting
Press the BRIGHT button so that the value
indicator disappears.
Focus Assist
The borderlines of focused images are
displayed in blue. Use these as a guide for
adjusting the focus precisely.
FOCUS
8 To cancel the focus assist mode
Press the FOCUS ASSIST button again.
8 To change the borderline color
Change the settings in [FOCUS ASSIST].
(੬ pg. 70)
NOTE
If you use focus assist in dark places, the
grainy sections gain color, and the color of the
borderline becomes difficult to see.
26
Nightalive
Spot Exposure Control
The shutter speed is automatically adjusted
from 1/2 to 1/250 seconds. It enables
recording with low light levels in dim locations.
Use this function when backlight
compensation does not work well, or to adjust
the brightness in the desired spot.
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
1 Press twice.
A
8 To cancel nightalive
Move the set lever to £(NIGHT) so that the
2 Select the desired spot metering area
indicator disappears.
5
frame.
NOTE
[ 5 h 5 6 m ]
Select
It is recommended to use the tripod (੬ pg. 18)
when recording with a slow shutter speed.
Set
Backlight Compensation
8 To lock the exposure
After you finish configuring the setting,
press and hold the set lever for more than 2
Backlight compensation brightens the subject
by increasing the exposure.
seconds. The indicator appears.
C
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
8 To cancel spot exposure control
Press the BACK LIGHT button once so
that the .indicator disappears.
8 To cancel backlight compensation
Press the BACK LIGHT button twice so
that the -indicator disappears.
27
Manual Recording (Continued)
3 Select the desired setting.
Manual Setting in Function Menu
Select
EFFECT
OFF
You can use manual recording functions
easily by selecting items in the function
menus.
SEPIA
MONOTONE
CLASSIC FILM
STROBE
Set
The following illustrations of display
screens are examples of when [EFFECT] is
set to [SEPIA].
4
FUNCTION
After performing “To Change to Manual
Recording Mode” (੬ pg. 24)
1
The menu disappears and the indicator for
the set function appears.
FUNCTION
WB
EFFECT
TELE MACRO
ZEBRA
CUSTOM SETTING
8 To return to the previous screen
Move the set lever to £.
8 To exit the screen
Press FUNCTION.
2 Select the desired menu.
For details on each menu, see below.
Select
EFFECT
OFF
SEPIA
MONOTONE
CLASSIC FILM
STROBE
Set
Menus
Settings: [ ] = Factory-preset
[AUTO]: White balance is adjusted automatically.
@
BMWB: Adjusts the white balance manually depending on the
light source.
1) Hold a sheet of plain white paper in
front of the subject so that the white
paper fills the screen.
2) Press and hold the set lever until the
Bindicator starts blinking then stops
blinking.
WB
Adjusts the white balance
to achieve the optimum
colors for the amount of
light in your surroundings
during recording.
DFINE: When shooting outdoors on a sunny day.
ECLOUD: When shooting outdoors on a cloudy day.
FHALOGEN: When a video light or similar type of lighting is used.
28
Menus
Settings: [ ] = Factory-preset
[OFF]: No effect is used.
JSEPIA: The image has a brownish tint like old photos.
KMONOTONE: The image becomes black and white like old
movies.
1
EFFECT
Enables you to record
videos or still images with
special effects.
LCLASSIC FILM*: This effect skips frames to give images of an
old movie atmosphere.
MSTROBE*: The image looks like a series of consecutive
snapshots.
TELE MACRO
Enables you to shoot
a subject as large as
possible at a distance of
approx. 40 cm (1.32 ft).
1[OFF]: Disables the function.
tON: Activates the function.
ZEBRA*
The sections of the
photographic subject that
are reflected as white due
to light are displayed in a
striped pattern. Use this
as a guide for adjusting
the brightness.
[OFF]: Deactivate this function.
70%: Sections that are close to being reflected as white (bright)
are displayed in a striped pattern.
100%: Sections that are completely reflected as white (too bright)
are displayed in a striped pattern.
CUSTOM SETTING*
Press down the set lever then select sub menus.
Adjust the sharpness moving the set lever to £/ ¤, then press
down.
SHARPNESS
Adjusts the
enhancement level
of the outline of the
recorded image.
NOTES
Several functions will not be accessible when sharpness is set.
Enhancing the sharpness causes the recorded image to appear
grainy.
•
•
COLOR BAR
The color bar will
be displayed. The
color characteristics
of the camera can
be confirmed by
[OFF]: Deactivate this function.
ON: Activate this function.
recording this display.
* Not available in #mode.
29
PLAYBACK
Playing Back Files
Video Playback
Slide the power/mode switch to
Press the PLAY/REC button to
select playback mode.
MODE to select
(video) mode.
!
VIDEO
8/8
MODE
The switch returns
to the original
position when it is
released.
SELECT
PLAY/REC
SELECT SET
SORT
The
lamp on the camera lights up.
The index screen for videos appears.
!
Move the set lever to ¡/ ¢/ £/ ¤
to select the desired file, then
press down.
Select
Set
8 To return to the index screen
Press INDEX.
8 To watch on TV
See page 36.
8 To turn the date display on/off
Change the settings in [DATE/TIME]. (੬ pg. 70)
8 To check the file information
Press INFO when playback is paused. (੬ pg. 40)
Operations during Playback
Return to the first
scene of the file
J : Turn down the
volume
Play/Pause
Forward search/
Frame-by-frame
playback
Reverse search/
Frame-by-frame
playback
(during pause)
(during pause)
Go to the first scene
of the next file
I : Turn up the
volume
During forward/reverse search, moving the set lever to £/ ¤
alters the search speed (maximum 60x).
30
Still Image Playback
Slide the power/mode switch to
Press the PLAY/REC button to
select playback mode.
MODE to select
mode.
(still image)
#
IMAGE
8/8
MODE
The switch returns
to the original
position when it is
released.
SELECT
PLAY/REC
SELECT SET
SORT
The index screen for still images
appears.
The
lamp on the camera lights up.
#
Move the set lever to ¡/ ¢/ £/ ¤
to select the desired file, then
press down.
Select
Set
8 To return to the index screen
Press INDEX.
8 To watch on TV
See page 36.
8 To turn the date display on/off
Change the settings in [DATE/TIME]. (੬ pg. 70)
8 To check the file information
Press INFO. (੬ pg. 40)
Operations during Playback
Rotate 90 degrees
(counterclockwise)
Start/end the slide show
Display the next file
Display the previous file
Rotate 90 degrees
(clockwise)
During the slide show, moving the set lever to ¡/ ¢changes the playback order.
31
Playing Back Files (Continued)
2 Select the recording date.
Select
JAN 07 2007
1/3
Power/Mode
Switch
Set
SELECT SET
SORT
3 Select the file you want to play back.
Select
Set
PLAY/REC
Button
Set Lever
FUNCTION
8 To return to the index screen
Press the INDEX button.
Event Screen – !mode only
You can search the desired file by the event
that you registered the file to when recording.
(੬ pg. 23) After searching by the event, you
can search by the recording date to narrow
down the search.
File Search Function
You can switch the index screen to the
date index screen or event screen for the
convenient file search.
The event screen can be used in
mode. It
Preparation:
!
cannot be used in
mode.
Slide the power/mode switch to MODE to
#
•
select
mode.
!
Date Index Screen
Press the PLAY/REC button to select the
•
playback mode.
You can search the desired file by the
recording date.
1 Press twice.
Preparation:
VACATION
1/ 3
Slide the power/mode switch to MODE to
•
select
or
mode.
! #
Press the PLAY/REC button to select
•
NEXT PAGE
SORT
playback mode.
INDEX
SELECT SET
1
SEARCH DATE
JAN 31 2007
JAN 25 2007
JAN 22 2007
DEC 22 2006
DEC 19 2006
DEC 01 2006
SELECT SET
INDEX
SORT
32
2 Select the event.
To Play Back TPD Files
– !mode only
To move to the next page, select [NEXT
PAGE].
SEARCH EVENT
Select
After backing up to a PC, the video files which
were edited on a PC and then recopied to the
camera will be stored in the EXTMOV folder
rather than the normal destination folder. This
file can then be played using the following
procedures.
ALL SCENES
JAN 25 2007
JAN 22 2007
Set
SELECT SET
SORT
3 Select the recording date.
Preparation:
To display all the files, select [ALL
SCENES].
Slide the power/mode switch to MODE to
•
select
mode.
!
Select
VACATION
1/3
Press the PLAY/REC button to select
•
playback mode.
1
DELETE
FUNCTION
PROTECT
Set
SELECT SET
SORT
EFFECT
WIPE/FADER
PLAYBACK PLAYLIST
EDIT PLAYLIST
PLAYBACK TPD FILE
PLAYBACK NORMAL FILE
4 Select the file you want to play back.
Select
2 Select [PLAYBACK TPD FILE].
Select
VIDEO [TPD]
8/8
Set
8 To return to the index screen
Press the INDEX button.
Set
SELECT SET
QUIT
8 To change the event registration of a file
See page 41.
3 Select the file you want to play back.
Select
Set
8 To exit the screen
Press FUNCTION.
8 To return to the normal file playback
mode
Select [PLAYBACK NORMAL FILE] in
step 2.
NOTE
During TPD file playback, you cannot use
some of the functions.
33
Playing Back Files (Continued)
4 Select the file you want to play back.
Playback with Special Effects
Select
Playback effects
Add effects that, for example, alter the color
tones of images.
Set
Preparation:
8 To exit the screen
Press FUNCTION.
Slide the power/mode switch to MODE to
•
select
or
mode.
! #
Press the PLAY/REC button to select the
•
8 To turn off the effect
Select [OFF] in step 3.
playback mode.
8 Items for EFFECT setting
1
DELETE
FUNCTION
PROTECT
SEPIA:
J
EFFECT
•
WIPE/FADER
PLAYBACK PLAYLIST
EDIT PLAYLIST
The image is given a brownish tint like an
old photo.
PLAYBACK TPD FILE
PLAYBACK NORMAL FILE
MONOTONE:
The image becomes black and white like
an old movie.
K
•
•
2 Select [EFFECT].
CLASSIC FILM*:
L
Select
The image is given an old movie
atmosphere by the effect of skipping
frames.
EFFECT
OFF
SEPIA
MONOTONE
CLASSIC FILM
STROBE
STROBE*:
The image looks like a series of
consecutive snapshots.
M
•
Set
SELECT SET
QUIT
3 Select a desired effect.
* Not available in #mode.
For details on each effect, see right
column.
Select
VIDEO
8/8
Set
SELECT SET
SORT
34
Wipe or fader effects – !mode only
Add effects at the beginning and end of
videos. These effects cannot be set for still
images.
8 Items for WIPE/FADER setting
FADER-WHITE:
Fade in or out with a white screen.
FADER-BLACK:
Fade in or out with a black screen.
O
P
Q
•
•
•
FADER-B.W:
Preparation:
Slide the power/mode switch to MODE to
Fade in to a color screen from a black
and white screen, or fade out in the
opposite way.
•
select
mode.
!
Press the PLAY/REC button to select
•
WIPE-CORNER:
R
playback mode.
•
•
Wipe in on a black screen from the upper
right to the lower left corner, or wipe out
in the opposite way.
1
DELETE
FUNCTION
PROTECT
EFFECT
WIPE/FADER
PLAYBACK PLAYLIST
EDIT PLAYLIST
WIPE-WINDOW:
S
PLAYBACK TPD FILE
PLAYBACK NORMAL FILE
The scene starts in the center of a black
screen and wipes in toward the corners,
or wipes out in the opposite way.
WIPE-SLIDE:
Wipe in from right to left, or wipe out in
the opposite way.
T
•
•
2 Select [WIPE/FADER].
Select
WIPE/FADER
1/2
OFF
WIPE-DOOR:
U
FADER-WHITE
FADER-BLACK
FADER-B.W
Wipe in as the two halves of a black
screen open to the left and right revealing
the scene, or wipe out in the opposite
way.
WIPE-CORNER
Set
SELECT SET
QUIT
3 Select a desired effect.
WIPE-SCROLL:
V
•
•
For details on each effect, see right
column.
The scene wipes in from the bottom to
the top of a black screen, or wipes out in
the opposite way.
Select
VIDEO
8/8
WIPE-SHUTTER:
W
Wipe in from the center of a black screen
toward the top and bottom, or wipe out in
the opposite way.
Set
SELECT SET
SORT
NOTE
4 Select the file you want to play back.
There is no effect on files with a play time
shorter than 7 seconds.
Select
Set
8 To exit the screen
Press FUNCTION.
8 To turn off the effect
Select [OFF] in step 3.
35
Watching Images on TV
This camera is designed to be used with
high-definition or NTSC-type color television
signals. It cannot be used with a television of
a different standard.
8 To connect using the COMPONENT
connector
COMPONENT
Connector
DC Connector
Connection with TV
You can output videos from the HDMI
connector, COMPONENT connector, or AV/S
connector. Select the connector that best suits
your television.
AC Adapter
Preparation: Turn off all units.
8 To connect using the HDMI connector
To AC
Outlet
AV Connector
HDMI Connector
DC Connector
AV Cable
Component
Cable
HDMI Cable
(optional)
AC Adapter
To AC
Outlet
COMPONENT
Input Connector
Audio L/R Input
Connector
Video Connector
is not in use.
NOTE
Change the settings in [COMPONENT
OUTPUT] as you like. (੬ pg. 71)
HDMI Connector
NOTE
Change the settings in [HDMI OUTPUT],
[HDMI COLOR SETTING] or [HDMI
ENHANCE SETTING] as you like. (੬ pg. 71)
36
8 To connect using the AV/S connectors
Playback Operation
After the connection with TV is
completed
S Connector
DC Connector
1 Turn on the camera and the TV.
2 Set the TV to its VIDEO mode.
3 (Only when connecting the camera to the
AC Adapter
VCR/DVD recorder)
To AC
Outlet
Turn on the VCR/DVD recorder, and
set the VCR/DVD recorder to its AUX
input mode.
AV Connector
4 Start playback on the camera.
(੬ pg. 30, 31)
8 To display camera’s on-screen display
on TV
Set [DISPLAY ON TV] to [ON]. (੬ pg. 71)
S Cable
(optional)
AV Cable
S Input Connector
AV Input Connector
NOTE
Change the settings in [VIDEO/S OUTPUT]
to suit the screen size of your television.
(੬ pg. 71)
37
EDITING/PRINTING
Managing Files
Preparation:
Set Lever
Slide the power/mode switch to MODE to
•
SNAP
SHOT
PLAY/REC
Button
select
or
mode.
! #
Press the PLAY/REC button to select
•
playback mode.
Zoom Lever
The following illustrations of display
screens are examples of when performing
[DELETE].
1
DELETE
FUNCTION
PROTECT
EFFECT
WIPE/FADER
PLAYBACK PLAYLIST
EDIT PLAYLIST
PLAYBACK TPD FILE
PLAYBACK NORMAL FILE
DIRECT
BACKUP/
EVENT
INFO
FUNCTION
CAUTION
2 Select [DELETE] or [PROTECT].
Select
Power/Mode
Switch
DELETE
CURRENT
FILE SELECT
DELETE ALL
Set
SELECT SET
QUIT
Do not remove the recording medium or
perform any other operation (such as turning
off the power) while accessing files. Also,
be sure to use the provided AC adapter, as
the data on the recording medium may be
corrupted if the battery becomes exhausted
during operation. If the data on the recording
medium becomes corrupted, format the
recording medium. (੬ pg. 72)
Deleting/Protecting the Currently
Displayed File
After performing steps 1-2
3 Select [CURRENT].
Select
DELETE?
REMAINING FILES:
0008
EXECUTE
Set
SELECT SET
Deleting/Protecting Files
You can select the previous or next file by
moving the set lever to £/ ¤.
Protected files cannot be deleted. To delete
them, release the protection first.
Once files are deleted, they cannot be
restored. Check files before deleting.
•
4 Select [EXECUTE].
•
Select
For an SD card, you can use the write/erase
•
protection tab to set protection. To protect
all the files, slide the tab to the “LOCK”
position.
Set
8 To exit the screen
Press FUNCTION.
Write/erase protection tab
38
Selecting and Deleting/Protecting Files
Deleting/Protecting All Files
After performing steps 1-2 (੬ pg. 38)
After performing steps 1-2 (੬ pg. 38)
3 Select [FILE SELECT].
3 Select [DELETE ALL] or [PROTECT
ALL].
Select
VIDEO DELETE
8/8
Select
DELETE ALL?
EXCEPT PROTECTED FILE
EXECUTE
Set
SELECT SET
QUIT
Set
SELECT SET
4 Select the desired file.
Select
VIDEO DELETE
8/8
4 Select [EXECUTE].
Select
Set
SELECT SET
QUIT
The or
mark appears on the file. To
$ x
Set
•
•
select other files, repeat this step.
If you slide the zoom lever towards T,
the preview screen is displayed. Sliding
the zoom lever towards W returns to the
index screen.
8 To exit the screen
Press FUNCTION.
8 To release protection
5
FUNCTION
Select the protected file in step 4
(“Selecting and Deleting/Protecting Files”
੬ left column).
DELETE?
QUIT
CANCEL
SELECT SET
8 To release protection of all files
1) In step 3, select [CANCEL ALL], then
press down the set lever.
6 Select [EXECUTE AND QUIT] (when
performing [DELETE]) or [QUIT]
(when performing [PROTECT]).
Select
2) Move the set lever to ¡/ ¢to select
[EXECUTE], then press down.
Set
8 To exit the screen
Press FUNCTION.
39
Managing Files (Continued)
Histogram – #mode only
Viewing File Information
A histogram is a graph indicating the image’s
brightness.
By checking the image and its histogram, you
can see the exposure level pattern and the
overall tone reproduction.
Preparation:
For !mode: Pause the playback.
Alternatively, select the file on the index
screen.
•
•
For #mode: Play back the still image.
Alternatively, select the file on the index
screen.
Preparation:
Play back the still image.
INFO
Press twice.
FILE
: MOV005.TOD
: PRG001
FOLDER
DATE/TIME
PB TIME
QUALITY
PROTECT
: JAN 1 06 10:56 AM
: 00:30:02
: FHD
INFO
: OFF
1/250 s
F3.5
FILE:
ISO100
D
B
•
•
•
•
•
•
•
File name
FOLDER:
Folder name
DATE/TIME:
Date and time of the recording
PB TIME (for video files):
Playback time (length of the file)
SIZE (for still images):
Image size (੬ pg. 69)
QUALITY:
A larger number of pixels in the center
position indicates correct exposure and well-
balanced brightness.
•
•
D
(Dim)
B
Brightness level
Image quality (੬ pg. 68, 69)
PROTECT:
File protection status (੬ pg. 38)
(Bright)
The shutter speed, F-number and ISO
sensitivity (GAIN) when recorded are also
displayed.
8 To turn off the file information display
Press INFO again.
8 To turn off the file information display
Press INFO several times.
NOTE
The shutter speed displayed during shooting
in auto mode is an approximation. It may not
match the one displayed with the histogram.
40
4
Changing the Event Registration of
Video Files after Recording
– !mode only
EVENT RE-REGISTRATION ENDS
DO YOU WANT TO SAVE?
DIRECT
BACKUP
/EVENT
DELETE AND QUIT
CANCEL
SELECT SET
Preparation:
Slide the power/mode switch to MODE to
•
5 Select [SAVE AND QUIT].
select
mode.
!
Select
Press the PLAY/REC button to select playback
•
mode.
1
VACATION
1/ 3
Set
DIRECT
BACKUP
/EVENT
NON SECTION
NEXT PAGE
QUIT
8 To exit the screen
SELECT REGISTER
Press FUNCTION.
2
Select a new event to register the file to.
To move to the next page, select [NEXT
•
PAGE].
To cancel the event registration, select
[NON SECTION].
•
VIDEO
8/8
Select
Set
SELECT SET
QUIT
3 Select the file you want to register.
Select
Set
To select other files, repeat this step.
If you slide the zoom lever towards T,
the preview screen is displayed. Sliding
the zoom lever towards W returns to the
index screen.
•
•
41
Managing Files (Continued)
To Extract a Still Image File From a
Video File – !mode only
DPOF Print Setting – #mode only
The number of prints to make of a still image
recorded on an SD card can be set. This
feature is useful when taking the SD card to a
photo lab for printing.
You can extract the desired scene from a
recorded video file, and record it as a still
image file.
Preparation:
Preparation:
Slide the power/mode switch to MODE to
Slide the power/mode switch to MODE to
•
•
select
mode.
#
select
mode.
!
Press the PLAY/REC button to select
Press the PLAY/REC button to select
•
•
•
playback mode.
Set [REC MEDIA FOR IMAGE] to [SD].
(੬ pg. 69)
playback mode.
1 Select the desired video file.
VIDEO
8/8
Select
1
FUNCTION
DELETE
PROTECT
COPY
MOVE
EFFECT
DPOF
Set
SELECT SET
SORT
Playback starts. Search the desired scene.
2 Select [DPOF].
Select
2
DPOF
SELECT IMAGES
ALL 1
CHECK SETTINGS
RESET
SNAP
SHOT
Set
SELECT SET
QUIT
NOTES
Setting Files Individually
Extracted still images are stored at a
resolution of 1920 x 1080. The image can
be elongated in the horizontal or vertical
directions depending on the picture quality
of the source video file.
•
After performing steps 1-2
3 Select [SELECT IMAGES].
Select
DPOF TOTAL:
0
8/8
Images cannot be extracted when the video
file is in search or slow-motion playback.
Extract images when the video is in normal
playback, or when it is paused.
The continuous shooting function (੬ pg. 69)
cannot be used to extract images.
•
•
Set
SELECT SET
QUIT
42
Setting All Files Together (One Print for
Each)
4 Select the desired file.
Select
After performing steps 1-2
3 Select [ALL1].
Set
Select
If you slide and hold the zoom lever
towards T, the preview screen of the still
image is displayed.
ALL1
CANCEL
Set
SELECT SET
5 Select the number of prints. (max. 15
prints)
4 Select [EXECUTE].
Select
Select
Set
Set
To set print information for other images,
repeat steps 4 and 5. (You can set up to
999 files.)
8 To exit the screen
Press FUNCTION.
6
FUNCTION
8 To cancel the selection
Set the number of prints to “00” in step 5.
8 To confirm DPOF settings
In step 3, move the set lever to ¡/ ¢to
select [CHECK SETTINGS], then press down.
If necessary, change the number of
prints for the desired file by following
steps 4 and 5.
•
8 To exit the screen
Press FUNCTION.
8 To cancel the selection
Set the number of prints to “00” in step 5.
8 To reset DPOF settings
1) In step 3, move the set lever to ¡/ ¢to
select [RESET], then press down.
2) Move the set lever to ¡/ ¢to select
[EXECUTE], then press down.
8 To confirm DPOF settings
In step 3, move the set lever to ¡/ ¢to
select [CHECK SETTINGS], then press down.
If necessary, change the number of
prints for the desired file by following
•
steps 4 and 5.
8 To reset DPOF settings
1) In step 3, move the set lever to ¡/ ¢to
select [RESET], then press down.
2) Move the set lever to ¡/ ¢to select
[EXECUTE], then press down.
43
Playlists – !mode only
3 Select [NEW LIST].
Power/Mode
Switch
Select
NEW LIST
PLAY/REC
Button
IMPORT FROM DATE
ALL SCENES
Set
SELECT SET
QUIT
4 Select an item and display files.
Select
Set
[IMPORT FROM EVENT]:
•
Search for an event and display the
corresponding files listed by recording
date.
FUNCTION
Set Lever
Move the set lever to ¡/ ¢/ £/ ¤to
select the event, then press down.
[IMPORT FROM DATE]:
Display all the files in the medium listed
by recording date.
[ALL SCENES]:
It is a list that enables you to organize
recorded videos in order of preference.
•
Preparation:
•
Slide the power/mode switch to MODE to
•
Display all files individually.
select
mode.
!
EDIT
Press the PLAY/REC button to select
•
playback mode.
TOTAL
00h00m
Creating Playlists
SELECT REGISTER
1
5 Select the file to add to playlist.
DELETE
FUNCTION
PROTECT
EFFECT
WIPE/FADER
Select
EDIT
PLAYBACK PLAYLIST
EDIT PLAYLIST
TOTAL
PLAYBACK TPD FILE
PLAYBACK NORMAL FILE
00h00m
Set
2 Select [EDIT PLAYLIST].
Files recorded in 1440 CBR video picture
quality are displayed with a 1440 CBR
icon.
To preview scenes, move the set lever
to ¡/ ¢to select the file and press the
INDEX button. When the index screen
of individual scenes appears, move the
set lever to ¡/ ¢/ £/ ¤to select the file,
then press down.
•
•
Select
EDIT PLAYLIST
NEW LIST
EDIT
RENAME
DELETE
Set
SELECT SET
QUIT
To return to previous screen, press
INDEX.
44
6 Select the insertion point.
Playing Back Playlists
Select
EDIT
TOTAL
30h15m
1
DELETE
FUNCTION
PROTECT
EFFECT
WIPE/FADER
PLAYBACK PLAYLIST
EDIT PLAYLIST
PLAYBACK TPD FILE
PLAYBACK NORMAL FILE
Set
SELECT REGISTER
To add other files, repeat steps 5 and 6.
To delete a registered scene, move the
set lever to ¡/ ¢to select the registered
file, then press down.
•
•
2 Select [PLAYBACK PLAYLIST].
Select
PLAYBACK PLAYLIST
7
01 2007 JAN.07 04:45PM
02 2007 JAN.07 09:25PM
03 2007 JAN.07 09:55PM
FUNCTION
QUIT PLAYLIST
SAVE EDITED CONTENTS?
DELETE AND QUIT
CANCEL
Set
SELECT SET
QUIT
SELECT SET
3 Select the playlist that you want to
play back.
8 Select [SAVE AND QUIT].
Select
Select
Set
Set
8 To exit the screen
Press FUNCTION.
8 To exit the screen
Press FUNCTION.
8 To stop playback
Press down the set lever.
NOTES
A maximum of 99 playlists can be created.
Each playlist can consist of a maximum of
99 scenes.
If you delete the original files, the
corresponding files are also deleted from
the playlist.
8 To return to the normal file playback
mode
Select [PLAYBACK NORMAL FILE] in
step 2.
•
•
•
8 To play back from the desired scene
1) In step 2, press the INDEX button. (The
index screen for playlist appears.)
2) Move the set lever to ¡/ ¢/ £/ ¤to
select the desired scene, then press
down.
45
Playlists – !mode only (Continued)
Deleting Playlist
Other Operations of Playlists
Original files are not deleted even if you
delete the playlist.
You can perform additional editing and delete
files in a created playlist.
Preparation:
Perform steps 1-2. (੬ pg. 44)
3 Move the set lever to ¡/ ¢to select
[DELETE], then press down.
Adding/Deleting Files in Playlist
4 Move the set lever to ¡/ ¢to select a
playlist you want to delete.
To delete all playlists at once, select
[DELETE ALL].
3 Move the set lever to ¡/ ¢to select
[EDIT], then press down.
4 Move the set lever to ¡/ ¢to select
the playlist you want to edit, then
press down.
To add or delete files, follow the steps 5 to
8 in “Creating Playlists”. (੬ pg. 44)
5 Press down the set lever.
6 Move the set lever to ¡/ ¢to select
[EXECUTE], then press down.
Changing Playlist Names
The default name of a playlist is its creation
date and time.
3 Move the set lever to ¡/ ¢to select
[RENAME], then press down.
4 Move the set lever to ¡/ ¢to select
the desired playlist, then press down.
5 Move the set lever to ¡/ ¢/ £/ ¤to
select the desired letter, then press
down.
Repeat this process to complete the
name.
•
You can change the character types
(capital letters, small letters or marks) by
selecting [A/a/@].
•
To correct a letter, select [}] or []] and
•
press down the set lever to move the
cursor to the letter, then select [CLEAR]
and press down the set lever.
6 Move the set lever to ¡/ ¢/ £/ ¤to
select [¯], then press down.
46
COPYING
Copying Files
Using a DVD Burner to Copy Files
from the Camera
Power/Mode
Switch
PLAY/REC
Button
The files in the camera can be backed up to a
DVD disc using a DVD burner (CU-VD40/
CU-VD20 sold separately).
Supported media: DVD-R, DVD-RW, DVD-R
•
DL (More than one disc may be required
depending on the size of the file to be
copied. In this case, use new (unused)
discs.)
This disc cannot be played in a normal DVD
player. Use one of the following methods to
view the disc.
•
— Playback the disc using the camera.
(“To play back the created disc using the
camera” ੬ pg. 48, 50)
FUNCTION
Set Lever
— Playback the disc using a DVD burner.*
(Only possible when using a CU-VD40.)
— Playback on a PC.*
* The disc must first be finalized on the
camera.
Types of Copying and Connectable Device
The Camera
Connection with a DVD Burner
You can copy still images
between the HDD and
SD card with this camera
alone. (੬ pg. 52)
Preparation:
Set the power/mode switch to OFF.
USB Connector
DC Connector
DVD Burner
(CU-VD40/CU-VD20)
You can copy video/still
image files recorded on
this camera onto DVD
discs. (੬ right column)
VCR/DVD Recorder
You can dub video
files recorded on this
camera onto DVD discs.
(੬ pg. 50)
USB Cable
USB Connector
AC Adapter
PC
To AC Outlet
You can copy video/still
image files on this camera
onto your PC. For details,
refer to PC OPERATION
section. (੬ pg. 53 to 66)
DVD Burner
NOTE
Use the USB cable that came with the DVD
burner.
Continued on next page
47
Copying Files (Continued)
Backup All Files
4 Select [EXECUTE] or [EXECUTE AND
FINALIZE].
Preparation:
Connect the camera to the DVD burner.
(੬ pg. 47)
Slide the power/mode switch to MODE to
By selecting [EXECUTE AND FINALIZE],
the disc is finalized after the files are
copied.
•
•
Select
select
or
mode.
! #
The following illustrations of display
screens are examples of when backing up
video files.
Set
The disc begins to be created. When
[COMPLETED] appears, press down the
set lever to complete the operation.
•
1 Select [NORMAL BACK-UP].
Select
NORMAL BACK-UP
When [COMPLETED. CHANGE DISC]
appears, change the disc. The second
disc begins to be created.
•
ALL
UNSAVED SCENES
To cancel the disc creation, select
[STOP].
•
Set
SELECT SET
TOP
2 Select the desired menu.
8 To return to the top screen
Press MENU, then move the set lever to
¡/ ¢to select [YES] and press down.
8 To finalize the disc after copy is finished
1) Connect the camera to the DVD burner.
(੬ pg. 47)
2) Turn the camera’s power on.
3) Select [FINALIZE].
[ALL]:
•
All files in the recording medium are
copied.
[UNSAVED SCENES/FILES NOT
BACKED-UP]:
•
Files that have never been copied to a
DVD disc are automatically selected and
copied.
4) Select [EXECUTE].
Select
VIDEOS ARE RECORDED
5) When [COMPLETED] appears, select
[OK].
FORMAT
CANCEL
8 To play back the created disc using the
camera
Set
SELECT SET
TOP
1) Connect the camera to the DVD burner.
(੬ pg. 47)
2) When watching on TV, connect the
camera to TV. (੬ pg. 36)
3) Turn the camera’s power on.
4) Select [PLAYBACK].
5) Select the desired folder.
6) Select the creation date of the disc.
7) Select the desired file. To return to
the previous screen, press the INDEX
button.
3 Select the desired menu.
[FORMAT]:
•
After the disc is formatted (all recorded
data on the disc is deleted), the files are
copied to the disc.
[CONTINUE TO COPY]:
•
Files are added to the free space of a
disc. Displayed only when a recordable
disc is inserted.
Select
DVD
DVD(DL)
5
3
EXECUTE AND FINALIZE
CANCEL
Set
SELECT SET
TOP
48
Select Files for Backup
Preparation:
[SELECT FROM PLAYLIST*]:
Select the desired playlist from the list
of playlists. The selected playlists are
displayed in a list.
1) Move the set lever to ¡/ ¢/ £/ ¤
to select the desired list, then press
down. To select other lists, repeat this
process.
•
•
Connect the camera to the DVD burner.
(੬ pg. 47)
•
Slide the power/mode switch to MODE to
•
select
or
mode.
! #
The following illustrations of display
screens are examples of when backing up
video files.
2) Move the set lever to ¤twice.
[SELECT FROM DATE]:
Files are sorted according to the date on
which they were recorded. Relevant files
are displayed in a list. Move the set lever
to ¡/ ¢to select the recording date,
then press down.
1 Select [SELECT BACK-UP].
Select
SELECT BACK-UP
SELECT FROM DATE
SELECT FROM SCENES
* Not available in #mode.
SELECT FROM EVENT
SELECT FROM PLAYLIST
Set
To preview scenes, press the INDEX
SELECT SET
TOP
button. (The index screen of individual
scenes appears.) Move the set lever to ¡/
¢/ £/ ¤to select the file, then press down.
To return to previous screen, press INDEX.
2 Select the desired menu.
Select
SELECT FROM EVENT
ALL
JAN.01.2007 12:04
JAN.01.2007 12:15
FEB.01.2007 12:04
FEB.01.2007 12:15
3 Select [ALL].
Set
SELECT SET
SORT
VIDEOS ARE RECORDED
[SELECT FROM SCENES/SELECT
FROM IMAGES]:
Register backup files individually.
1) Move the set lever to ¡/ ¢/ £/ ¤
to select the desired file, then press
down. To select other files, repeat this
process.
2) Press the INDEX button then go to
step 4.
[SELECT FROM EVENT*]:
Files are sorted according to event.
Relevant files are displayed in a list.
Move the set lever to ¡/ ¢/ £/ ¤to
select the event, then press down.
•
•
FORMAT
CANCEL
SELECT SET
TOP
4 Select the desired menu.
[FORMAT]:
•
After the disc is formatted (all recorded
data on the disc is deleted), the files are
copied to the disc.
[CONTINUE TO COPY]:
•
Files are added to the free space of a
disc. Displayed only when a recordable
disc is inserted.
Select
DVD
DVD(DL)
5
3
EXECUTE AND FINALIZE
CANCEL
Set
SELECT SET
TOP
Continued on next page
49
Copying Files (Continued)
5 Select [EXECUTE] or [EXECUTE AND
Using a VCR/DVD Recorder to Dub
Files from the Camera
FINALIZE].
By selecting [EXECUTE AND FINALIZE],
the disc is finalized after the files are
copied.
You can connect the camera to a VCR or DVD
recorder, and dub the camera’s files directly
onto those devices.
Select
Connection with a VCR/DVD Recorder
You can connect using either the i.LINK
connector or AV/S connector. Select the
connector that best suits your VCR/DVD
recorder.
Set
The disc begins to be created. When
[COMPLETED] appears, press down the
set lever to complete the operation.
•
When [COMPLETED. CHANGE DISC]
appears, change the disc. The second
disc begins to be created.
To cancel the disc creation, select
[STOP].
Preparation: Turn off all units.
8 To connect using the i.LINK connector
•
i.LINK Connector
DC Connector
•
8 To return to the top screen
Press MENU, then move the set lever to
¡/ ¢to select [YES] and press down.
8 To finalize the disc after copy is finished
1) Connect the camera to the DVD burner.
(੬ pg. 47)
2) Turn the camera power on.
3) Select [FINALIZE].
i.LINK Cable
(optional)
AC Adapter
4) Select [EXECUTE].
5) When [COMPLETED] appears, select
[OK].
i.LINK Connector
8 To play back the created disc using the
camera
To AC Outlet
1) Connect the camera to the DVD burner.
(੬ pg. 47)
2) When watching on TV, connect the
camera to TV. (੬ pg. 36)
3) Turn the camera’s power on.
4) Select [PLAYBACK].
5) Select the desired folder.
6) Select the creation date of the disc.
7) Select the desired file. To return to
previous screen, press the INDEX
button.
VCR/DVD Recorder
NOTES
When dubbing using the i.LINK connector,
only the playlist which has been played for
dubbing can be dubbed. (੬ pg. 51) Normal
video files and normally played playlists
cannot be dubbed.
When copying using the i.LINK connector,
only files which are recorded in 1440 CBR
video picture quality can be dubbed. If a DV
input compatible device is connected, files
recorded in other picture quality can also be
dubbed. Set the [i.LINK OUTPUT (DUB)] to
[DV]. (੬ pg. 71)
•
•
50
8 To connect using the AV/S connectors
Dubbing Operation
1 Set the VCR/DVD recorder to its AUX
S Connector
DC Connector
input mode.
Check that the images from the camera
have been input correctly to the VCR/DVD
recorder.
2 Start playback on the camera.
To play back videos (੬ pg. 30)
To play back playlists
•
•
AC Adapter
To AC
Outlet
1) Press the FUNCTION button.
2) Move the set lever to ¡/ ¢to select
[PLAYBACK PLAYLIST], then press
down.
AV Connector
3) Move the set lever to ¤. *1
4) Move the set lever to ¡/ ¢to select
[START PLAYBACK], then press down.
(A black screen is displayed for five
seconds at the first and the last
scene. *2)
When dubbing using the i.LINK
connection and with [i.LINK OUTPUT
(DUB)] set to [1440 CBR], a
1
*
S Cable
(optional)
AV Cable
confirmation screen is displayed after
operation. Select [OK] and proceed to
step 4).
When dubbing using the i.LINK
connection and with [i.LINK OUTPUT
(DUB)] set to [1440 CBR], the image
to be dubbed is not displayed on the
camera’s screen. Check the images on
the VCR/DVD recorder side.
2
*
VCR/DVD
Recorder
S Connector
AV Connector
3 At the point you want to start
dubbing, start recording on the VCR/
DVD recorder.
Refer to the VCR/DVD recorder’s
instruction manual
.
8 To stop dubbing
Stop recording on the VCR/DVD recorder,
then press the REC button again.
NOTES
The date displays cannot be dubbed using
the i.LINK connection.
•
When playing back images dubbed using
the i.LINK on a VCR/DVD recorder, the
images may stop momentarily at junctions
between scenes.
•
51
Copying Files (Continued)
4
Copying/Moving Still Image Files
You can copy or move still image files
between the HDD and SD card using the on-
screen display.
Preparation:
5 Set the file unit ([ALL] or [FILE]) to
Slide the power/mode switch to MODE to
copy/move.
•
select
mode.
#
Press the PLAY/REC button to select
•
•
•
playback mode.
Make sure that SD card is inserted in the
SD slot.
Make sure that enough free space is left in
the copy/move destination medium.
[FILE]:
•
Select when you want to transfer the
selected files.
1
1) Move the set lever to ¡/ ¢/ £/ ¤
to select the desired file, then press
down.
FUNCTION
DELETE
PROTECT
COPY
MOVE
EFFECT
DPOF
The smark appears on the file. To
•
select other files, repeat this step.
2) Press FUNCTION.
2 Select [COPY] or [MOVE].
[ALL]:
•
[COPY]:
•
Select when you want to transfer all files
in the recording medium.
Files are copied to the destination
medium while leaving original files in the
source medium.
[MOVE]:
6 Select [EXECUTE].
•
Files are moved to the destination
medium while deleting original files
(except read-only files) in the source
medium.
Select
Set
Select
IMAGE COPY
MEDIA
ALL
File transfer starts. When [COPYING/
MOVING COMPLETED] appears, press
down the set lever.
FILE UNIT
NUMBER OF FILE
0059
EXECUTE
CANCEL
Set
SELECT SET
QUIT
8 To exit the screen
3 Set the direction of copy/move.
Press MENU, then move the set lever to
¡/ ¢to select [EXECUTE] and press
down.
(HDD ] SD or SD ] HDD)
8 To stop the file transfer
1) Press down the set lever.
2) Select [EXECUTE] and press down the
set lever.
52
PC OPERATION
File Backup on the PC – Windows®
System Requirements
Power/Mode Switch
Set Lever
OS:
Windows® XP Home Edition [XP] (pre-
installed),
or Windows® XP Professional [XP] (pre-
installed)
CPU:
Intel® Pentium® 4, at least 2.4 GHz
(at least 3.0 GHz recommended)
Intel® Pentium® M, at least 1.6 GHz
RAM:
At least 512 MB (at least 1 GB recommended)
Free hard disk space:
At least 750 MB for installation
For creating Blu-ray disc, at least 30 GB (at
least 60 GB recommended)
DIRECT BACKUP/
EVENT
Connector:
Install the software that came with the camera
to your PC.
USB 2.0 connector
Sound card:
Direct Sound compatible sound card
Display:
Must be capable of displaying at least
1024 x 768 (XGA) in high color 16 bit or higher
(1280 x 1024 (SXGA) or higher is recommended)
Intel/nVidia/ATI MPEG-2 HD DxVA compatible
card
You can back up your files on your computer
with a simple one-touch operation, edit your
files on your computer, and also create discs.
If you cannot install the software, you can
still back up your files on your computer.
(੬ pg. 58)
Miscellaneous:
Internet Explorer 5.5 or later
DirectX 9.0 or later
DirectX is automatically installed during
installation.
Supported media:
BD-RE, BD-R, DVD-R/-RW, DVD+R/+RW,
CD-R/RW
For the compatible drives:
powerproducer/3/comp_dvd_drives.jsp
Q You can perform detailed settings for each
item.
R Select a function on the right, and an
explanation is displayed.
S The operating procedure for each function
is displayed.
T Plays back video files on the PC (੬ pg. 59)
U Plays back still image files on the PC
(੬ pg. 59)
For the compatible BD drives:
ev/eng/support.htm
NOTE
V Creates discs/Edits files (੬ pg. 60)
W Backs up camera files onto the PC
(੬ pg. 57)
Even if your system meets the recommended
requirements above, you may still experience
dropped frames while playing back high
definition video, or you may find that editing
takes a long time. In order to use these
functions more smoothly, it is recommended
that you use a higher performance computer
(CPU: Intel® CoreTM 2 Duo, memory: 2GB or
more).
You can find the latest information on the
provided software program at CyberLink’s
co.jp/products/ne/
53
File Backup on the PC – Windows® (Continued)
2 Click [Easy Installation].
Software Installation
If you want to specify the type of software
to install or the installation destination
folder etc., select [Custom Installation].
Follow the instructions on the screen to
install the software.
The following software is included in the CD-
ROM that came with your camera.
CyberLink BD Solution
•
Comprehensive application software that
consists of the following 3 software.
PowerCinema NE for Everio
The main authoring software.You can
perform various operations such as file
backup, playback, and editing from the top
menu of this software.
PowerProducer 3 NE
Allows you to create discs. Automatically
starts from an operation in PowerCinema
NE for Everio.
PowerDirector 5 NE Express
Allows you to edit files on your PC.
Automatically starts from an operation in
PowerCinema NE for Everio.
3 Click [Yes].
Digital Photo Navigator 1.5
Allows you to change the format of still
image files backed up on your computer.
•
Preparation:
Quit any other software you are using. (Check
that there are no other application icons on
the status bar.)
4 Select the desired language and click
1 Load the provided CD-ROM into the
[OK].
PC.
After a moment, the [SETUP] screen
appears. If the [SETUP] screen does not
appear, double-click the CD-ROM icon in
[My Computer].
54
5 Click [Yes].
The software installation starts.
6 Click [Finish].
8 When installation is completed
The installed software is displayed in [All
Programs].
The backup destination folder [MyWorks]
for files is created on the hard disk drive
that has the most free space.
55
File Backup on the PC – Windows® (Continued)
8 When you have finished operation
Always follow the procedures below when
Connecting the Camera to the PC
disconnecting the camera, or turning off the
camera/computer power.
Failing to do so may cause damage to the
camera and computer.
Preparation:
Set the camera’s power/mode switch to OFF.
USB Connector
DC Connector
1) Confirm that the access/charge lamp on
the camera does not light or blink.
(If the access/charge lamp lights or
blinks, wait until it is turned off before
proceeding.)
2) Double-click the [Safely Remove
Hardware] or [Unplug or Eject Hardware]
icon in the status bar.
3) Select [USB Mass Storage Device] or
[USB Disk], and then click [Stop].
4) Click [OK].
USB Cable
AC Adapter
5) Disconnect the USB cable.
6) Turn off the camera and PC.
To AC Outlet
USB Connector
NOTES
When the USB cable is connected, turning
on or off the camera causes malfunctions of
the PC.
•
Connect the camera directly to the PC, not
through the hub.
•
Do not use an extension USB cable.
Saving the wrong kinds of files in a
recording medium or deleting files or
folders from a recording medium can cause
problems with the operation of the camera.
When it is necessary to delete a file from
a recording medium, delete it through the
camera. Also, do not move or rename
folders and files in the medium on PC.
Never disconnect the USB cable while the
access/charge lamp on the camera lights or
blinks.
•
•
•
56
File Backup from the specified media
Preparation:
File Backup on the PC
This method uses the included software to
back up files onto your computer.
Video files that have never been backed
up onto the connected computer are
automatically selected from the back up
history and backed up.
If you could not install the software, turn to
pg. 58 for details of how to back up your files
without using this software.
Install the software from the included CD-
ROM. (੬ pg. 54)
•
Connect the camera to the computer with
the USB cable. (੬ pg. 56)
•
1 Set the camera’s power/mode switch
to STANDBY/ON.
Preparation:
Install the software from the included CD-
ROM. (੬ pg. 54)
PLAYBACK ON PC
BACK UP
•
Connect the camera to the computer with
the USB cable. (੬ pg. 56)
•
SELECT SET
QUIT
1 Set the camera’s power/mode switch
to STANDBY/ON.
2 On the camera, move the set lever
to ¡/ ¢to select [BACK UP], then
press down.
2 On the camera, press the DIRECT
BACK UP button.
A dialog box is displayed on the PC
screen. However, you do not need to
use the dialog box. File copy starts
automatically.
3 Click [EVERIO_HDD] or [EVERIO_
SD].
When the progress bar disappears, the
process is complete.
When the progress bar disappears, the
process is complete.
NOTE
When backup is performed, a folder for each
of the media (HDD or SD) stored in the
[MyWorks] folder (੬ pg. 55) is created, and
the files are backed up inside those folders.
(If backup is performed from more than one
camera HDD, that number of HDD folders is
created.)
57
File Backup on the PC – Windows® (Continued)
4 Double-click [EVERIO_HDD] or
File Backup on the PC without Using
[EVERIO_SD].
Software
Preparation:
Connect the camera to the computer with the
USB cable. (੬ pg. 56)
1 Create a folder to back up files into.
5 Select the folder that you want to
back up, and drag & drop it into the
folder you created in step 1.
SD_VIDEO:
•
Folder that contains video files. If you
want to back up files individually, open
this folder, and drag & drop folders such
as [PRG001] one by one.
DCIM:
Folder that contains still image files. If
you want to back up files individually,
open this folder, and drag & drop files
2 Set the camera’s power/mode switch
•
to STANDBY/ON.
such as [PIC_0001.JPG] one by one.
PLAYBACK ON PC
BACK UP
SELECT SET
QUIT
3 On the camera, move the set lever to
¡/ ¢to select [PLAYBACK ON PC],
then press down.
NOTE
For further details on the use of folders,
please refer to pg. 73.
58
Other PC Operations – Windows®
4 Click the media that contains desired
Playing back Files on the PC
files.
Preparation:
Install the software from the included CD-
ROM. (੬ pg. 54)
•
Connect the camera to the computer with
the USB cable. (੬ pg. 56)
•
1 Set the camera’s power/mode switch
to STANDBY/ON.
5 Click the desired file.
PLAYBACK ON PC
BACK UP
You can use the convenient file search
function.
Sort by:
•
The order of files is rearranged according
to item that you selected.
SELECT SET
QUIT
Filter by:
Files are filtered according to the item
that you selected.
•
2 On the camera, move the set lever to
¡/ ¢to select [PLAYBACK ON PC],
then press down.
A dialog box is displayed on the PC
screen. However, you do not need to
use the dialog box. PowerCinema starts
automatically.
3 Click [Browse Videos] (for video
playback) or [Browse Pictures] (for
still image playback).
59
Other PC Operations – Windows® (Continued)
3 Click [Copy/Edit].
Creating Discs/Editing Files
Preparation:
Install the software from the included CD-
ROM. (੬ pg. 54)
•
Connect the camera to the computer with
the USB cable. (੬ pg. 56)
•
1 Set the camera’s power/mode switch
to STANDBY/ON.
4 Click the media that contains desired
PLAYBACK ON PC
BACK UP
files.
SELECT SET
QUIT
2 On the camera, move the set lever to
¡/ ¢to select [PLAYBACK ON PC],
then press down.
A dialog box is displayed on the PC
screen. However, you do not need to
use the dialog box. PowerCinema starts
automatically.
5 Click the check box of the desired
file.
The smark appears in the check box.
To select other files, repeat this step.
60
6 Click [Copy/Advanced function].
7 Click [Create Disc] for creating discs,
or [Advanced Editing] for editing.
PowerProducer (for creating discs) or
PowerDirector (for editing) starts. For
more information on detailed operations
of these softwares, refer to their Read
me (੬ pg. 62) or CyberLink web site.
(੬ pg. 53)
NOTES
Supported media is BD-RE, BD-R,
DVD-R/-RW, DVD+R/+RW, CD-R/RW.
•
DVD-RAM discs cannot be used. Regarding
•
DVD-R/DVD+R discs, only unused DVD-R/
DVD+R discs can be used. Regarding
DVD-RW/DVD+RW discs, used DVD-RW/
DVD+RW discs can also be used, but they
need to be formatted before recording.
Formatting a disc deletes all content
recorded on the disc up until that time.
You may not able to play back the created
•
disc depending on the performance
of a device. Also the image may stop
momentarily at junctions between scenes.
PC must be equipped a compatible drive
and player software to playback the created
disc.
•
Edited files should be read and played back
with PowerDirector.
•
61
Other PC Operations – Windows® (Continued)
Digital Photo Navigator 1.5
Getting More Use from the Software
The User’s Guide is included on the CD-ROM
in PDF format.
For more information on detailed operations
of the software, see the Tutorials for each
software program or the User’s Guides.
1 Load the provided CD-ROM into the
PC.
PowerCinema NE for Everio
2 Right-click the CD-ROM icon in [My
1 Select [PowerCinema NE for Everio]
Computer], then click [Open].
from [All Programs].
3 Double-click the [DOCS] folder.
2 Click [Tutorial].
4 Open the “Start.pdf” file and click the
button of the desired language.
PowerProducer 3 NE
NOTES
1 Select [PowerProducer 3 NE] from
[All Programs].
You need to connect to the Internet to be
•
able to see the Tutorial.
Adobe® Acrobat® ReaderTM or Adobe®
•
2 Click [Readme].
Reader® must be installed to read PDF
files. Adobe® Reader® can be loaded from
PowerDirector 5 NE Express
1 Select [PowerDirector 5 NE Express]
from [All Programs].
2 Click [User’s Guide] or [Readme].
62
Contact us for information on the included software
Use of this software is authorized according to the terms of the software license.
JVC
When contacting the nearest JVC office or agency in your country about this software (refer
e.html), please fill out the following and have the appropriate information ready.
Product Name
Model
Problem
PC
•
•
•
•
•
Manufacturer
Model (Desktop/Laptop)
CPU
OS
Error Message
Memory (MB)
Available Hard Disk Space (MB)
Please note that it may take some time to respond to your questions, depending on their subject
matter.
JVC cannot answer questions regarding basic operation of your PC, or questions regarding
specifications or performance of the OS, other applications or drivers.
CyberLink
Telephone/fax support
Office hours
(Mon. to Fri.)
Location
Language
Phone #
Fax #
English / German /
French / Spanish /
Italian / Dutch
9:00 am to
5:00 pm
+49-700-462-
92375
Germany
+49-241-70525-25
+886-2-8667-1300
9:00 am to
6:00 pm
+886-2-8667-1298
ext. 333
Taiwan
Japan
Mandarin
Japanese
10:00 am to
5:00 pm
+81-3-3516-9555 +81-3-3516-9559
Paid voice support
Lines are open
(Mon. to Fri.)
Location
Language
English
URL
1:00 pm to 10:00 pm
CST
new_site/voice_support.jsp
U.S.A.
Support web/e-mail
Language
URL/e-mail address
index.html
English
German / French / Spanish /
Italian
Japanese
63
File Backup on the PC – Macintosh
You can back up camera files onto your
computer.
Software Installation
Furthermore, if the software from the included
CD-ROM is installed, the backed up file can
be viewed in Quick Time Player or edited in
iMovie HD or Final Cut Pro. (Several functions
will not be accessible.)
Preparation:
Quit any other software you are using.
1 Load the provided CD-ROM into the
PC.
You can find the latest information on the
provided software program at our world wide
ne/
2 Double-click the CD-ROM icon.
System Requirements
Hardware:
Macintosh 1.25 GHz or faster Power PC G4/
G5 or Intel® processor (at least Intel® CoreTM
Duo recommended.)
USB 2.0 connector is required.
OS:
Mac OS X (10.4.4 to 10.4.8)
RAM:
3 Double-click the QuickTime
Component for Everio icon.
At least 512MB (at least 1GB recommended)
4 Click [Continue].
64
5 Click [Continue].
Connecting the Camera to the PC
Preparation:
Set the camera’s power/mode switch to OFF.
DC Connector
USB Connector
6 Click [Install].
The software installation starts.
USB Cable
AC Adapter
To AC Outlet
7 Click [Close].
USB Connector
NOTES
When the USB cable is connected, turning
on or off the camera causes malfunctions of
the PC.
•
Connect the camera directly to the PC, not
through the hub.
•
Do not use an extension USB cable.
Saving the wrong kinds of files in a
recording medium or deleting files or
folders from a recording medium can cause
problems with the operation of the camera.
When it is necessary to delete a file from
a recording medium, delete it through the
camera. Also, do not move or rename
folders and files in the medium on PC.
Never disconnect the USB cable while the
access/charge lamp on the camera lights or
blinks.
•
•
•
Continued on next page
65
File Backup on the PC – Macintosh (Continued)
8 When you have finished operation
Always follow the procedures below when
disconnecting the camera, or turning off the
camera/computer power.
3 On the camera, move the set lever to
¡/ ¢to select [PLAYBACK ON PC],
then press down.
Failing to do so may cause damage to the
camera and computer.
1) Drag & drop the recording medium icon
on the desktop into the [Trash] icon.
If the confirmation message appears,
click [OK].
2) Confirm that the access/charge lamp on
the camera does not light or blink.
If the access/charge lamp lights or
blinks, wait until it is turned off before
proceeding.
3) Disconnect the USB cable.
4) Turn off the camera and PC.
4 Double-click [EVERIO_HDD] or
[EVERIO_SD].
5 Select the folder that you want to
back up, and drag & drop it into the
folder you created in step 1.
File Backup on the PC
SD_VIDEO:
•
Preparation:
Connect the camera to the computer with the
USB cable. (੬ pg. 65)
Folder that contains video files. If you
want to back up files individually, open
this folder, and drag & drop folders such
as [PRG001] one by one.
1 Create a folder to back up files into.
DCIM:
•
Folder that contains still image files. If
you want to back up files individually,
open this folder, and drag & drop files
such as [PIC_0001.JPG] one by one.
2 Set the camera’s power/mode switch
to STANDBY/ON.
PLAYBACK ON PC
BACK UP
NOTE
For further details on the use of folders,
please refer to pg. 73.
SELECT SET
QUIT
66
FURTHER INFORMATION
Changing the Menu Settings
3 Select the desired menu from the first
menu item.
MENU
[VIDEO]:
•
Display menus related to !mode.
[IMAGE]:
•
Display menus related to #mode.
[GENERAL]:
•
Display menus common to !and #
modes.
[OUTPUT SETTING]:
Display menus related to image output
when connecting to other devices.
•
[MEDIA]:
Display menus related to recording
media (HDD and SD cards).
•
Set Lever
GENERAL
Select
DISPLAY
DISPLAY ON TV
LANGUAGE
CLOCK ADJUST
DATE DISPLAY STYLE
The following illustrations of display
screens are examples of when [DEMO
MODE] is set to [OFF].
Set
SELECT SET
QUIT
4 Select the desired menu from the
second menu item.
1
VIDEO
SCENE COUNTER
EXTERNAL MIC LEVEL
QUALITY
ZOOM
OIS
MENU
For details on each menu, see page 68
to 72.
Select
DEMO MODE
SELECT SET
QUIT
ON
OFF
VIDEO
2
SCENE COUNTER
EXTERNAL MIC LEVEL
QUALITY
Set
SELECT SET
QUIT
ZOOM
OIS
SELECT SET
5 Select the desired setting from the
QUIT
third menu item.
Select
Set
8 To return to the previous screen
Move the set lever to £.
8 To exit the screen
Press MENU.
67
Changing the Menu Settings (Continued)
Menus
Settings: [ ] = Factory-preset
[FHD]: Record in 1920 x 1080i (full high-definition),
VBR (Variable Bit Rate). Select this to record in the
highest picture quality.
SP: Record in 1440 x 1080i (high-definition), VBR
(Variable Bit Rate). Select this in order to record for
a long time.
1440 CBR: Record in 1440 x 1080i (high-definition),
CBR (Constant Bit Rate). Select this to copy a
recorded video using the i.LINK connector.
nQUALITY
Enables you to set the picture
quality for videos.
NOTE
If you switch the quality settings, a new file management
folder is created in the HDD or SD card. If you change
the settings frequently, you may not be able to record due
to a limited quantity of folders. In this case, perform the
operation shown on page 79.
[10X] / 40X / 200X
@ZOOM
NOTE
Enables you to set the maximum
zoom ratio.
When the smallest value is set, the optical zoom is used.
When one of the larger values is set, the digital zoom is
used.
OFF: Disables the function.
[ON]: Activates the function.
NOTES
qOIS
Accurate stabilization may not be possible if hand shake
is excessive, or depending on the shooting conditions.
Compensates for hand shake.
•
Switch off this mode when recording with the camera on a
tripod.
•
pGAIN UP
Makes the subject appear bright
automatically when you record in
dark places. However, the overall
color tones appear grayish.
OFF: Disables the function.
[ON]: Activates the function.
[OFF]: Disables the function.
ON: Activates the function.
oWIND CUT
Reduces noise caused by wind.
[HDD] / SD
NOTE
/REC MEDIA FOR VIDEO
Enables you to set the recording
medium for videos.
When set to [SD], video picture quality will automatically be
set to [SP].
hSCENE COUNTER
Enables you to set whether to
display the scene counter.
[OFF]: Disables the function.
ON: Activates the function.
|EXTERNAL MIC LEVEL
Enables you to set whether
display the input level when the
external microphone (optional) is
connected.
OFF: Disables the function.
[ON]: Activates the function.
68
Menus
Settings: [ ] = Factory-preset
[FINE] / STANDARD
nQUALITY
Enables you to set the picture
quality for still images.
yIMAGE SIZE
Enables you to select the picture [1920 x 1080] / 1440 x 1080 / 1024 x 768 / 640 x 480
size for still images.
2GAIN
You can set the ISO setting to
[AUTO] / 100 / 200 / 400
increase the sensitivity in dark
conditions.
[OFF]: Disables the function.
ON: Activates the function.
BRACKETING: Activates the bracket shooting function.
In addition to an image with the exposure set by
the camera, two other images are recorded with
exposure values shifted to the + 0.3 EV and – 0.3
{CONTINUOUS SHOOTING
EV sides.You can select the image that has a
Records still images continuously
suitable exposure after shooting.
while the SNAPSHOT button is
NOTES
pressed.
The interval between recording still images is approx. 0.5
seconds.
Continuous shooting may not work well depending on the
recording medium.
The continuous shooting speed will drop if this function is
used repeatedly.
•
•
•
[OFF] / 2SEC / 10SEC
NOTES
zSELF-TIMER
Starts recording when the
set time elapses after the
SNAPSHOT button is pressed.
The operation of the timer can be confirmed by the tally
lamp.
•
This can also be used to prevent vibration by hand.
•
3REC MEDIA FOR IMAGE
Enables you to set the recording
medium for still images.
[HDD] / SD
9LANGUAGE
[ENGLISH] / FRANÇAIS / ESPAÑOL /
Enables you to set the display
language. (੬ pg. 17)
PORTUGUÊS /
/
/
:CLOCK ADJUST
Enables you to set the time.
(੬ pg. 17)
DATE / TIME
DATE STYLE:
year.month.day / [month.day.year] / day.month.year
TIME:
24h / [12h]
;DATE DISPLAY STYLE
Enables you to set the date and
time display format.
69
Changing the Menu Settings (Continued)
Menus
Settings: [ ] = Factory-preset
OFF: The date/time does not appear.
[AUTO]: The date/time appears for approx. 5 seconds in
the following cases.
<DATE/TIME
Enables you to set whether to
display the current time on the
LCD monitor.
When the power/mode switch is set from OFF to
STANDBY/ON
•
When playback starts
•
ON: The date/time is always displayed.
EXECUTE: Performs this function.
[CANCEL]: Returns to the menu screen without
executing reset.
ZPRESET
Returns all the camera settings
to their default values.
gBRIGHT
Adjust the brightness of the display moving the set lever
to £/ ¤, then press down.
Enables you to set the brightness
of the LCD monitor or viewfinder.
OFF: Disables the function.
[ON]: Activates the function.
To turn the unit on when the drop detection
worked, set the power/mode switch to OFF, and to
STANDBY/ON again.
^DROP DETECTION
HDD by turning off the power
automatically when the camera
detects that it has been dropped.
Prevents damage to the
CAUTION
Setting this function to off increases the chances of
damaging the built-in hard disk if the camera is accidentally
dropped.
NFOCUS ASSIST
When the focus assist function
is used, the borderline of the
focused subject is displayed in
the selected color.
[BLUE] / RED / GREEN
]REMOTE
OFF: The camera does not receive the signal from the
remote control.
[ON]: Enables operation with the remote control.
Turns reception of the operation
signal from the remote control
on/off.
OFF: Disables the function.
[ON]: Activates the function.
NOTES
[DEMO MODE
Introduces special features of
the camera when there is no
operation for about 3 minutes
during recording mode.
The demonstration only works when the AC adapter is
connected, not with the battery.
•
If an SD card is in the camera, demonstration will not take
place even if this mode is set to [ON].
•
\OPERATION SOUND
Enables you to set the operation
sound or turn the operation
sound on/off.
OFF: Turns off the operation sound.
[MELODY]: The melody sounds when any operation is
performed.
OTALLY LAMP
OFF: Unlit.
[ON]: Lit.
Set whether to light the tally lamp
while shooting.
70
Menus
Settings: [ ] = Factory-preset
PPRIORITY SETTING
[LCD MONITOR]: Projects the image onto the LCD
monitor.
FINDER: Projects the image onto the viewfinder.
Set whether to project the
image onto the LCD monitor or
viewfinder when both are open.
lDISPLAY
OFF: Turns off the on-screen display.
[ON]: Turns on the on-screen display.
Enables you to set whether to
display the on-screen display.
[OFF]: Does not display on TV.
ON: Displays on TV.
NOTE
When connected to a TV using the i.LINK cable, the
camera’s on-screen display is not displayed on the TV, even
if this setting is [ON].
%DISPLAY ON TV
Used for displaying camera’s on-
screen display on a TV screen.
RVIDEO/S OUTPUT
Set the television screen size
(16:9/4:3) of the connected
television when outputting from
the AV/S connector.
4:3 / [16:9]
SCOMPONENT OUTPUT
Set the definition of the video
output from the COMPONENT
connector.
[480i]: Outputs at 480i.
1080i: Outputs at 1080i.
[AUTO]: The definition that best suits the connected
device is automatically selected in the following
order: 1080i, 480p.
THDMI OUTPUT
Set the definition of the video
output from the HDMI connector.
480p: Outputs at 480p. Select when the video is not
projected correctly.
UHDMI COLOR SETTING
Set the video format of the video
output from the HDMI connector.
[AUTO]: Select this under normal circumstances.
RGB: Select when the video is not projected correctly.
VHDMI ENHANCE SETTING
Select whether or not to
automatically adjust the image
quality (depth of color, dark color
suppression etc) of video output
when connecting to the TV’s DVI
connector.
[OFF]: Image quality is not automatically adjusted.
ON: Image quality is automatically adjusted.
Wi.LINK OUTPUT (DUB)
When using the i.LINK connector
to copy files, set according to the
type of device connected or file
picture quality.
DV: Select when copying with a device that supports
DV input.
[1440 CBR]: Select when copying video that was
recorded with [1440 CBR] set as the [QUALITY].
71
Changing the Menu Settings (Continued)
Menus
Settings: [ ] = Factory-preset
Connect the AC adapter.
)CLEAN-UP HDD
EXECUTE: Performs this function. Select [OK] when
completed.
[CANCEL]: Cancels this function.
Writing speed to HDD tends to
become slow after long periods
of repeated use. Execute cleanup
periodically to regain the writing
speed.
NOTE
Depending on the condition of the HDD, it may take several
minutes for the cleanup process to be completed.
EXECUTE: Performs this function. Select [OK] when
completed.
[CANCEL]: Cancels this function.
*FORMAT HDD
This will ensure stable speeds
and operation when accessing
the hard disk drive.
NOTES
Be aware that all files and data including protected files
will be erased by the formatting process.
•
Do not format the recording medium on your PC.
•
+DELETE DATA ON HDD
This will make it more difficult to
recover data on the HDD which
has already been erased. It is
recommended that you do this
when disposing of the camera
to prevent illegal data recovery
(using commercially available
software).
Connect the AC adapter.
EXECUTE: Performs this function. Select [OK] when
completed.
[CANCEL]: Cancels this function.
EXECUTE: Performs this function. Select [OK] when
completed.
[CANCEL]: Cancels this function.
,FORMAT SD CARD
You have to format newly
purchased SD cards with this
camera before using them.
This will also ensure stable
speeds and operation when
accessing the SD card.
NOTES
Be aware that all files and data including protected files
will be erased by the formatting process.
•
Do not format the recording medium on your PC.
•
-VIDEO NO. RESET
.IMAGE NO. RESET
By resetting the file number
(name), a new folder will be
made. The new files you are
going to make will be stored in
the new folder.
EXECUTE: Performs this function. Select [OK] when
completed.
[CANCEL]: Cancels this function.
It is convenient to separate
the new files from previously
recorded files.
72
Folder Structure and Extensions
Recording medium
X = number
[DCIM]
Contains the still image folders.
[XXXJVCSO]
[XXXJVCSO]
[XXXJVCSO]
Contains the video file folders.
[SD_VIDEO]
[MGR_INFO]
[PRGXXX]
[PRGXXX.PGI]
Management information* for the media as a
whole
Management information*
Video file
[MOVXXX.TOD]
[MOVXXX.MOI]
Management information* for the video file
[PRGXXX]
[PRGXXX]
After backing up to a PC, the video files which
were edited on a PC and then recopied to the
camera are saved.
[EXTMOV]
[MOV_XXXX.TPD]
[MOV_XXXX.TPD]
[MOV_XXXX.TPD]
[MISC]
[PRIVATE]
Contains folders with DPOF setting data.
Contains management information files of event
information and/or DVD creation for the files taken
with the camera.
* Information such as the date and time of recording, recorded with the video file.
Extensions
Video files
Still image files
: “.TOD”
: “.jpg”
The file extension may not appear depending on the [FOLDER] option setting of Windows®.
73
Troubleshooting
The camera is a microcomputer-controlled
device. External noise and interference (from
a TV, a radio, etc.) might prevent it from
functioning properly.
To solve the problem, first follow the
instructions below.
If the problem is not solved, reset the
camera. (੬ below)
If the problem persists, please consult your
nearest JVC dealer.
•
•
•
The following phenomena are not
malfunctions.
8 To reset the camera
The camera heats up when it is used for a
long time.
•
1) Set the power/mode switch to OFF and
remove the power supply (battery pack
or AC adapter) from the camera, then
reattach it.
2) Execute [PRESET] from the menu.
(੬ pg. 70)
The battery heats up during charging.
When playing back a video file, the
image stops momentarily or the sound is
interrupted at junctions between scenes.
•
•
Trouble
Action
੬
Connect the AC adapter securely.
Detach the battery pack once again and re-attach it firmly.
Replace the dead battery with a fully charged one.
16
16
–
•
•
•
•
No power is supplied.
If the camera is not operated for 5 minutes while the
power is on, it turns itself off automatically to conserve
power. To turn the camera on again when using the
battery pack, set the power/mode switch to OFF, then to
STANDBY/ON. When using the AC adapter, perform any
operation such as zooming.
–
No display appears.
Adjust the brightness of the LCD monitor or viewfinder.
When using the viewfinder, the LCD monitor is opened.
Either close the LCD monitor, or set the [PRIORITY
SETTING] to [FINDER].
70
71
•
•
Move to a place where no vibration or excessive sound.
The drop detection function operated. Set the power/
mode switch to OFF, and to STANDBY/ON again. To turn
off this function, set [DROP DETECTION] to [OFF].
–
70
•
•
The power was turned
off accidentally.
Fully charge the battery, and then run it down. If the
problem persists, the battery is worn out and needs to be
replaced. Please purchase a new one.
The displayed amount
of remaining battery
power differs from the
actual operating time.
16
•
Make sure to use the camera under appropriate operating
temperatures.
The battery is worn out and needs to be replaced. Please
purchase a new one.
The power does not
turn on, or the battery
operation time is
extremely short even
after the battery is
fully charged.
80
–
•
•
Charging is difficult in places subject to extremely
high/low temperatures. To protect the battery, it is
recommended to charge it in places with a temperature
of 10°C to 35°C (50°F to 95°F).
When the battery is already fully charged, the lamp does
not light. Check the remaining battery power.
–
•
The access/charge
lamp on the camera
does not light during
charging.
18
•
74
Trouble
Action
੬
Adjust the brightness and angle of the LCD monitor.
When the LCD monitor’s LED light reaches the end of
its service life, images on the LCD monitor become dark.
Consult your nearest JVC dealer.
70
–
•
•
Images on the LCD
monitor appear dark
or whitish.
The LCD monitor is made with high precision technology.
However, black spots or bright spots of light (red, green
or blue) may appear constantly on the LCD monitor.
These spots are not recorded on the picture. This is not
due to any defect of the unit.
–
•
Colored bright spots
appear on the LCD
monitor.
(Effective dots: more than 99.99 %)
Recording medium is full. Delete unnecessary files or
replace the SD card.
Select the recording medium properly.
38
•
Recording cannot be
performed.
68, 69
–
•
•
Such a phenomenon occurs when shooting a subject
illuminated by bright light. This is not a malfunction.
Vertical lines appear
on recorded images.
Such a phenomenon occurs when shooting under direct
sunlight. This is not a malfunction.
–
70
–
The LCD monitor
becomes red or black
for an instant.
•
•
•
Set [DATE/TIME] to [ON].
During recording, the
date/time does not
appear.
The temperature of the camera is increasing. If the
camera continues to heat up, recording may be stopped
to protect the recording medium. In this case, turn off the
power, and then wait until the camera cools down.
During video
recording, the 7REC
indicator flashes.
Certain modes of program AE, effect, OIS, and other
functions that cannot be used together are selected at
the same time.
–
•
The LCD monitor
indications blink.
Change the settings in [ZOOM].
Digital zoom is not available in the still image recording
mode.
68
–
•
•
Digital zoom does not
work.
Set focus to the automatic mode.
Clean the lens and check the focus again.
26
79
The focus is not
adjusted automatically.
•
•
•
Wait to become natural color. The camera adjusts the
white balance automatically but it takes a time.
Try manual white balance adjustment.
In bright places, setting “Nightalive” or a slow speed is
not recommended.
When the recorded image is too dark, try backlight
compensation or adjust brightness.
–
28
–
•
•
The color of the
image looks strange.
26, 27
26
•
•
When the recorded image is too bright, try adjust
brightness.
Do not select the sepia (SEPIA) or monotone
(MONOTONE) mode before setting white balance.
29
–
White balance setting
cannot be activated.
•
•
The continuous shooting speed will drop when
repeatedly making continuous shots, when using certain
recording media, or under certain recording conditions.
The continuous
shooting speed is
slow.
75
Troubleshooting (Continued)
Trouble
Action
੬
Select the recording medium properly.
To watch images on a TV, set the TV’s input mode or
channel that is appropriate for video playback.
68, 69
37
•
•
Playback cannot be
performed.
Do not select the sepia (SEPIA) or monotone
(MONOTONE) mode before setting white balance.
34
–
The black & white
fader does not work.
•
•
The sound of the hard disk drive may have been
recorded if the camera was moved suddenly during
recording. Do not move or shake the camera suddenly
during recording.
There is a noise
during playback.
The temperature of the camera is increasing. If the
camera continues to heat up, playback may be stopped
to protect the recording medium. In this case, turn off the
power, and then wait until the camera cools down.
–
•
•
During video
playback, the U
indicator flashes.
Change the settings in [VIDEO/S OUTPUT] so that it
matches the screen size of the connected TV.
71
Aspect ratio of the
image is strange
when watching
images on your TV.
Set [HDMI OUTPUT] to [AUTO].
71
–
When outputting from
the HDMI connector,
a part of the TV
screen appears to be
shaking.
•
•
Some functions cannot be used when playing back a
disc that was created with a DVD burner. (E.g.: Slow-
motion playback, frame-by-frame playback, playback
effects etc.)
Some functions
cannot be used when
using the camera
to playback a disc
created with a DVD
burner.
Remove protection from the files and delete them.
38
Files cannot be
deleted.
•
•
There is a large number of still images (approx. 1,000 or
more) stored in the recording medium. Copy the stored
files to other devices, and delete them from the recording
medium.
47, 53
The data process is
too slow after the
power is switched
on or the mode is
changed.
Push the SD card in a few more times.
19
The SD card cannot
be removed from the
camera.
•
76
Trouble
Action
੬
Linked operation from an i.LINK connection is not
supported.
–
When connected
with the i.LINK
cable, the camera
does not operate
even if controls are
attempted from the
PC etc.
•
Output files recorded in [1440 CBR] quality from the
i.LINK connection for dubbing.
— When dubbing, change the [i.LINK OUTPUT (DUB)]
setting to [1440 CBR].
— Only playlists that are played back for dubbing can be
output via i.LINK.
50
44
•
•
Dubbing cannot
be done in high-
definition.
In order to allow high definition dubbing, the [i.LINK
OUTPUT (DUB)] setting of this camera is set to [1440
CBR] in the factory. Due to this setting, files other than
those recorded at 1440 CBR quality are not output. If you
want to perform dubbing in high definition quality, do not
include files recorded at a quality other than 1440 CBR in
the playlist.
When connected to a device that supports DV input, you
can output files recorded at other quality settings. Set
the [i.LINK OUTPUT (DUB)] setting to [DV]. However, the
quality of the dubbed images will be the standard quality.
When connecting using an AV/S cable, you can output
files irrespective of the quality. However, the quality of the
dubbed images will be the standard quality.
When dubbing a
playlist using i.LINK
output, some videos
cannot be played
back.
71
51
•
•
77
Warning Indications
Indication
Meaning/Action
੬
Displays the remaining battery power.
–
•
•
High
Exhausted
(Battery indicator)
As the battery power comes close to nil, the battery
indicator blinks. When the battery power is exhausted,
power turns off automatically.
–
Appears when the date/time is not set.
17
16
•
•
The built-in clock’s rechargeable lithium battery is
discharged, so the previously set date/time is erased.
Connect the camera to an AC outlet using the AC adapter
for over 24 hours to charge the clock’s lithium battery. Then
set the date/time.
SET DATE/TIME!
Appears for 5 seconds after power is turned on in recording
mode if the lens cover is closed or when it is dark.
–
•
•
LENS COVER
Remove the card once and insert it again. At this time,
switch the camera’s power on after inserting the SD card. If
the error is not cancelled, replace the card with one that has
been guaranteed for correct operation.
19
HDD ERROR!
MEMORY CARD
ERROR!
Perform clean up to restore the capacity of the recording media.
72
38
•
•
Appears when you attempt recording when the write/erase
protection tab on the SD card is set to the “LOCK” position.
CHECK CARD’S WRITE
PROTECTION SWITCH
The video management file is broken. Recovery is required
to record or play back video files. Move the set lever to ¡/
¢to select [YES], then press down to recover the video
management file.
–
VIDEO MANAGEMENT
FILE IS BROKEN.TO
RECORD/PLAYBACK
VIDEO, RECOVERY IS
REQUIRED. RECOVER?
•
Appears when the event information cannot be read.
–
CAN NOT READ EVENT
INFORMATION
•
•
The writing speed of recording medium is slow, or the
recording medium is corrupted. Use an SD card that is
guaranteed to operate.
19
The recording medium was subjected to vibrations or jolts.
Be careful not to subject the recording medium to vibrations
or jolts.
Appears when the recording medium is full and recording
is not possible. Delete unnecessary files, or replace the SD
card.
–
•
•
RECORDING FAILURE
38
Appears when an incompatible USB device is connected to
the camera.
Appears when a DVD burner that is switched off is
connected. If you want to use the DVD burner, switch the
power on.
–
–
•
•
INCOMPATIBLE USB
DEVICE
78
Indication
Meaning/Action
੬
The data may not be recorded on the recording medium
correctly. Try recording again.
Otherwise, replace the SD card.
–
RECORDING MAY NOT
BE CORRECT ON THE
MEMORY CARD
•
19
–
•
•
To turn the unit on again, set the power/mode switch to
OFF, and to STANDBY/ON again.
DROP DETECTION
WORKED AND THE
POWER IS TURNED
OFF
Cannot record because the number of file management
folders on either the HDD or SD card has reached the
maximum number. Backup your files to other media, and
then perform the following operations to reset the folder
numbers.
–
•
NUMBER OF FOLDERS
OVERFLOW
1) Select and set [FORMAT HDD] (to reset the HDD folder
numbers) or [FORMAT SD CARD] (to reset the SD card
folder numbers).
2) With [EXECUTE] selected, hold down the DIRECT BACK
UP button and press down the set lever.
3) When [OK] is displayed, press down the set lever to
complete the process.
Cleaning
Before cleaning, turn off the camera and remove the battery pack and AC adapter.
8 To clean the exterior
Wipe gently with a soft cloth. If the camera is particularly dirty, dip the cloth into diluted mild
soap and wring it out well before wiping. Then wipe again with a dry cloth.
8 To clean the LCD monitor
Wipe gently with a soft cloth. Be careful not to damage the monitor.
8 To clean the lens
Wipe gently with lens cleaning paper.
NOTES
Avoid using strong cleaning agents such as benzine or alcohol.
Mold may form if the lens is left dirty.
When using a cleaner or chemically treated cloth, refer to the cautions for each product.
•
•
•
79
Specifications
8 For video/Audio
Format
SD-VIDEO
Recording/Playback format
Video: MPEG-2 TS
Audio: MPEG-1 Layer 2
Signal format
1080/60i
Recording mode (video)
FHD:VBR, average of 26.6 Mbps
SP: VBR, average of 19 Mbps
1440 CBR: CBR, 27 Mbps
Recording mode (audio)
48 kHz, 384 kbps
Camera
8 For general
Power supply
DC 11 V (Using AC adapter)
DC 7.2 V (Using battery pack)
Power consumption
Approx. 7.1 W (When using the LCD monitor)
Approx. 6.7 W (When using the viewfinder)
Approx. 7.7 W (Maximum; when recording)
Dimensions (W x H x D)
91 mm x 77 mm x 186 mm
(3-5/8" x 3-1/16" x 7-3/8")
Weight
Approx. 665 g (1.5 lbs)
(incl. strap)
Approx. 750 g (1.7 lbs)
(incl. battery and strap)
Operating temperature
0°C to 40°C (32°F to 104°F)
Operating humidity
35% to 80%
Storage temperature
–20°C to 50°C (–4°F to 122°F)
8 For still image
Format
JPEG
Image size
4 modes (1920 x 1080 / 1440 x 1080 /
1024 x 768 / 640 x 480)
Picture quality
2 modes (FINE/STANDARD)
8 For connectors
HDMI
HDMI Ver.1.2a output
Component output
Y, Pb, Pr component output
i.LINK output
4-pin (I.LINK/IEEE1394 compliant)
Pickup
1/5" (570,000 pixels) progressive CCD
Lens
F 1.8 to 1.9, f = 3.3 mm to 33.0 mm, 10:1
power zoom lens
Filter diameter
ø46.0 mm
LCD monitor
2.8" diagonally measured, LCD panel/TFT
active matrix system
Viewfinder
Electronic viewfinder with 0.57" color LCD
Speaker
Monaural
S output
Y: 1.0 V (p-p), 75 Ω
C: 0.29 V (p-p), 75 Ω
AV output
Video output: 1.0 V (p-p), 75 Ω
Audio output: 300 mV (rms), 1 kΩ
USB
Mini USB type A and type B, USB 2.0
compliant
Language
English/French/Spanish/Portuguese/
Japanese/Korean/Traditional Chinese
Microphone
ø3.5mm stereo mini jack
AC Adapter
Power requirement
AC 110 V to 240 Vd, 50 Hz/60 Hz
Output
DC 11 V
, 1 A
§
80
Dimensions (W x H x D)
42 mm x 14.5 mm x 91 mm
(1-11/16" x 5/8" x 3-5/8")
Weight
Approx. 30 g (0.07 lbs)
(incl. battery)
Remote Control
Power supply
DC 3 V
Battery life
Approx. 1 year (depending on the frequency of
use)
Operating distance
Within 5 m (16.4 ft)
Operating temperature
0°C to 40°C (32°F to 104°F)
Design and specifications subject to change
without notice.
Approximate recording time (minutes) (for video)
SDHC
Card
Recording medium
HDD
Quality
60 GB
300
4 GB
–
FHD
SP
420
25
–
1440 CBR
300
Approximate number of storable images (for still image)
HDD
SD Card
1 GB
Recording medium
Image size/Quality
1440 x 1080 / FINE
60 GB
9999
9999
9999
9999
9999
9999
9999
9999
512 MB
740
2 GB
2880
4540
5700
9080
9999
9999
2160
3440
4 GB
5760
9080
9999
9999
9999
9999
4320
6880
1440
2270
2850
4540
7140
9999
1080
1720
1440 x 1080 / STANDARD
1024 x 768 / FINE
1160
1460
2320
3650
6400
550
1024 x 768 / STANDARD
640 x 480 / FINE
640 x 480 / STANDARD
1920 x 1080 / FINE
1920 x 1080 / STANDARD
880
81
Cautions
AC Adapter
Recording Medium
When using the AC adapter in areas other
than the USA
The provided AC adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
Be sure to follow the guidelines below
to prevent corruption or damage to your
recorded data.
•
Do not bend or drop the recording medium, or
•
subject it to strong pressure, jolts or vibrations.
Do not splash the recording medium with water.
Do not use, replace, or store the recording
medium in locations that are exposed to strong
static electricity or electrical noise.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to
an AC wall outlet other than American National
Standard C73 series type use an AC plug
adapter, called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest
JVC dealer.
•
•
Do not turn off the camera power or remove
•
the battery or AC adapter during shooting,
playback, or when otherwise accessing the
recording medium.
Plug Adapter
Do not bring the recording medium near objects
that have a strong magnetic field or that emit
strong electromagnetic waves.
•
Do not store the recording medium in locations
with high temperature or high humidity.
•
Do not touch the metal parts.
•
When formatting or erasing data using the
camera, only the file administration information
is changed. The data is not completely erased
from the hard disk. If you want to completely
erase all of the data, we recommend either
using commercially available software that
is specially designed for that purpose, or
by physically destroying the camera with a
hammer etc.
•
Battery Packs
The supplied battery
Terminals
pack is a lithium-ion
battery. Before using
the supplied battery
pack or an optional
battery pack, be sure
to read the following
cautions:
LCD Monitor
To avoid hazards
... do not burn.
•
To prevent damage to the LCD monitor, DO
NOT
... push it strongly or apply any shocks.
... place the camera with LCD monitor on the
bottom.
To prolong service life
... avoid rubbing it with coarse cloth.
•
... do not short-circuit the terminals. Keep it away
from metallic objects when not in use. When
transporting, make sure the provided battery
cap is attached to the battery. If the battery
cap is misplaced, carry the battery in a plastic
bag.
•
... do not modify or disassemble.
... do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause
the battery to overheat, explode or catch fire.
... use only specified chargers.
Main Unit
For safety, DO NOT
... open the camera’s chassis.
... disassemble or modify the unit.
... allow inflammables, water or metallic objects
to enter the unit.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
camera is not in use.
... place naked flame sources, such as lighted
candles, on the apparatus.
... expose the apparatus to dripping or splashing.
•
To prevent damage and prolong service life
•
... do not subject to unnecessary shock.
... charge within the temperature range of 10°C
to 35°C (50°F to 95°F). This is a chemical
reaction type battery — cooler temperatures
impede chemical reaction, while warmer
temperatures can prevent complete charging.
... store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
... fully charge and then fully discharge the
battery every 6 months when storing the
battery pack over a long period time.
... remove from charger or powered unit when
not in use, as some machines use current
even when switched off.
82
Avoid using the unit
•
Declaration of Conformity
Model Number : GZ-HD7U
Trade Name : JVC
Responsible party : JVC AMERICAS CORP.
Address : 1700 Valley Road Wayne, N. J.
07470
... in places subject to excessive humidity or dust.
... in places subject to soot or steam such as
near a cooking stove.
... in places subject to excessive shock or
vibration.
... near a television set.
... near appliances generating strong magnetic
or electric fields (speakers, broadcasting
antennas, etc.).
... in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or
32°F) temperatures.
... in places subject to the air pressure is low
(more than 3000 m (9870 ft) above the sea
level).
Telephone Number : 973-317–5000
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
DO NOT leave the unit
•
... in places of over 50°C (122°F).
... in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
... in direct sunlight.
Changes or modifications not approved
by JVC could void the user’s authority to
operate the equipment. This equipment has
been tested and found to comply with the
limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following
measures: Reorient or relocate the receiving
antenna. Increase the separation between the
equipment and receiver.
... in a closed car in summer.
... near a heater.
... in high places such as on a TV. Leaving the
unit in high places while a cable is connected
may result in a malfunction if the cable is
caught and the unit falls onto the floor.
To protect the unit, DO NOT
•
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration
during transportation.
... keep the lens directed at extremely bright
objects for long periods.
... expose the lens to direct sunlight.
... swing it excessively when using the hand
strap.
... swing the soft camera case excessively when
the camera is inside it.
How to Handle a CD-ROM
Take care not to soil or scratch the mirror
•
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/
TV technician for help.
surface (opposite to the printed surface). Do
not write anything or put a sticker on either the
front or back surface. If the CD-ROM gets dirty,
gently wipe it with a soft cloth outward from the
center hole.
Do not use conventional disc cleaners or
cleaning spray.
Do not bend the CD-ROM or touch its mirror
surface.
Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
•
•
•
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
83
Terms
A
AC Adapter ................................................ 16, 82
M
Manual Recording ........................................... 24
Menu Settings ................................................. 67
Adjust Brightness ............................................ 26
Aperture Priority .............................................. 25
AV/S Connection ................................. 37, 51, 71
N
O
Nightalive ......................................................... 27
On-Screen Display .......................................... 71
Operation Sound ............................................. 70
Optical Image Stabilizer (OIS) ......................... 68
B
C
Backlight Compensation .................................. 27
Battery Pack ........................................ 16, 18, 82
Brightness Control (LCD Monitor/Viewfinder) . 70
P
PC ............................................................. 53, 64
Picture Quality ........................................... 68, 69
Playlist ............................................................. 44
Power-Linked Operation .................................. 12
Preset .............................................................. 70
Program AE ..................................................... 24
Protecting Files ............................................... 38
Clean-up HDD ................................................. 72
Clock Adjust .............................................. 17, 69
Color Bar ......................................................... 29
Component Connection ............................ 36, 71
Continuous Shooting ....................................... 69
Copying (Moving) Still Images . 47, 50, 52, 53, 64
Copying Video Files ....................... 47, 50, 53, 64
R
S
Recordable Time/Number of Images ............... 81
Recording Medium ........................ 23, 68, 69, 82
Remote Control ................................... 11, 13, 70
Resetting the Camera ..................................... 74
Resetting the File Number ............................... 72
D
Date/Time ........................................................ 70
Date Display Style ........................................... 69
Date Index Screen ........................................... 32
Deleting Files ............................................ 38, 72
Deleting Playlist ............................................... 46
Demonstration Mode ....................................... 70
Display on TV .................................................. 71
DPOF .............................................................. 42
Drop Detection ................................................ 70
DVD Burner ..................................................... 47
DVD Recorder ................................................. 50
Scene Counter ................................................ 68
SD Card .......................................................... 19
Self-Timer ........................................................ 69
Sharpness ....................................................... 29
Shutter Speed ................................................. 25
Slide Show ...................................................... 31
Speaker Volume .............................................. 30
Spot Exposure Control .................................... 27
Still Image ................................................. 21, 31
E
F
Effect ......................................................... 29, 34
Event Registration ..................................... 23, 41
Event Screen ................................................... 32
External Microphone ................................. 13, 68
T
Tally Lamp ................................................. 13, 70
Tele Macro ....................................................... 29
Tripod Mounting ............................................... 18
TV .................................................................... 36
File Information ................................................ 40
Focus ............................................................... 26
Focus Assist .............................................. 26, 70
Formatting a Recording Medium ..................... 72
V
VCR ................................................................. 50
Video ......................................................... 20, 30
Viewfinder .................................................. 22, 71
G
H
I
Gain ................................................................. 69
Gain Up ........................................................... 68
W
Z
White Balance ................................................. 28
Wind Cut ......................................................... 68
Wipe or Fader Effects ...................................... 35
Hard Disk ........................................................ 82
HDMI Connection ...................................... 36, 71
i.LINK Connection ..................................... 50, 71
Image Rotation ................................................ 31
Image Size ...................................................... 69
Zebra ............................................................... 29
Zooming .................................................... 22, 68
L
Language Setting ...................................... 17, 69
LCD Monitor ........................................ 12, 14, 82
Lens Cover ...................................................... 18
Printed in Japan
0607FOH-AL-VP
US
© 2007 Victor Company of Japan, Limited
|