JVC GY HD201E User Manual

INTRODUCTION

CONTROLS,

INDICATORS AND

CONNECTORS

PREPARATIONS

FOR OPERATION

SETTING AND

ADJUSTMENTS

BEFORE SHOOTING

SHOOTING

OPERATION

HD CAMERA RECORDER

PLAYBACK MODE

USING EXTERNAL

COMPONENTS

INSTRUCTIONS

GY-HD200U/CHU

GY-HD200E/CHE

GY-HD201E/CHE

MENU SCREENS

FEATURES OF THE

CAMERA SECTION

OTHERS

The illustration shows the GY-HD200U/

GY-HD200E/GY-HD201E HD CAMERA

RECORDER with the provided lens,

viewfinder and microphone attached.

Thank you for purchasing this JVC product. Before operating this

device, please read the instructions carefully to ensure the best

possible performance.

For Customer Use:

Enter below the Serial No. which is located on the body.

Retain this information for future reference.

Model No.

Serial No.

LST0512-001A

WARNING:

Information for Users on Disposal of

Old Equipment

Safety Precautions (Cont’d)

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

This unit should be used with 12V DC only.

CAUTION:

FOR EUROPE

To prevent electric shocks and fire hazards, do NOT

use any other power source.

This equipment is in conformity with the provisions and protection

requirements of the corresponding European Directives.

This equipment is designed for professional video appliances and

can be used in the following environments:

NOTE:

Attention:

This symbol is only valid in the European

Union.

The rating plate (serial number plate) is on the bottom of the unit.

residential area (in houses)

commercial and light industry; e.g. offices or theatres

urban outdoors

CAUTION:

To prevent electric shock, do not open the cabinet. No user ser-

[European Union]

viceable parts inside. Refer servicing to qualified service person-

nel.

This symbol indicates that the electrical and electronic equip-

ment should not be disposed as general household waste at

its end-of-life. Instead, the product should be handed over to

the applicable collection point for the recycling of electrical

and electronic equipment for proper treatment, recovery and

recycling in accordance with your national legislation.

In order to keep the best performance and furthermore for electro-

magnetic compatibility we recommend to use cables not exceeding

the following length:

Due to design modifications, data given in this instruction book are

subject to possible change without prior notice.

Camera

The apparatus shall not be exposed to dripping or splashing and

that no objects filled with liquids, such as vases, shall be placed

close to the apparatus.

Port

Cable

Length

2 m

By disposing of this product correctly, you will help to con-

serve natural resources and will help prevent potential nega-

tive effects on the environment and human health which

could otherwise be caused by inappropriate waste handling

of this product. For more information about collection point

and recycling of this product, please contact your local

municipal office, your household waste disposal service or

the shop where you purchased the product.

DC IN

Exclusive Cable

Coaxial Cable

Shielded Cable

VIDEO

Y, PB, PR

3 m

Worded - “CAUTION - Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equivalent type.”

3 m

AUDIO INPUT1,

INPUT2

3 m

AUDIO OUT CH1,

CH2

Shielded Cable

3 m

Penalties may be applicable for incorrect disposal of this

waste, in accordance with national legislation.

Phones1, 2

Exclusive Cable

2 m

IEEE1394 (HDV/DV) Exclusive Cable

REMOTE Exclusive Cable

4.5 m

5 m

(Business users)

If you wish to dispose of this product, please visit our web

page www.jvc-europe.com to obtain information about the

take-back of the product.

Caution: Where there are strong electromagnetic waves or mag-

netism, for example near radio or TV transmitter, transformer,

motor, etc., the picture and the sound may be disturbed. In such

case, please keep the apparatus away from the sources of the dis-

turbance.

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accor-

dance with applicable national legislation or other rules in

your country for the treatment of old electrical and electronic

equipment.

Dear Customer,

This apparatus is in conformance with the valid European direc-

tives and standards regarding electromagnetic compatibility and

electrical safety.

European representative of Victor Company of Japan Limited is:

JVC Technology Centre Europe GmbH

P.O. Box 10 05 52

61145 Friedberg

Germany

III

Thank you for purchasing the JVC HD CAMERA RECORDER.

These instructions are for the GY-HD200U/CHU, GY-

HD200E/CHE and GY-HD201E/CHE.

•

Camera section designed with 3-CCD system for high-

quality picture

1/3" 3-CCD with 1,110,000 effective pixels employed. Dig-

ital signal processing for reproduction of HDV/DV high-

quality picture.

ACCESSORIES

MAIN FEATURES

•

A lens is included with the GY-HD200U, GY-HD200E and

GY-HD201E.

lens is not included with the GY-HD200CHU, GY-

Multi-Zone Auto Iris Detection Circuit

HD200CHE and GY-HD201CHE.

IEEE1394 input is possible with the GY-HD200U/CHU and

GY-HD201E/CHE.

Multi-zone auto iris detection circuit ensures optimum iris

position even in back light conditions or when a bright sub-

ject moves in a frame.

This device records in HDV format or DV format. DV for-

mat can record and play back SD (Standard Definition)

video on Mini DV videocassettes.

Explanations concerning unique GY-HD200U/CHU and GY-

HD201E/CHE functions are set off by the (GY-HD200U/GY-

HD201E only) notice.

Information applicable only to the GY-HD200U/CHU is

marked by “(U model only)”.

HDV format can record and play back HD (High Definition)

video on Mini DV videocassettes.

There are two types of recording formats within HDV format.

HDV 720p (720 effective scan lines, progressive scan)

HDV 1080i (1080 effective scan lines, interlaced scan)

•

Safety Zone indication in viewfinder

Zebra pattern video level indication in viewfinder

Full Auto Shooting (FAS) function

This device supports HDV 720p format. (HDV 720p)

Information applicable only to theGY-HD200E/CHE, GY-

HD201E/CHE is marked by “(E model only)”.

Eliminates the need for troublesome switch or filter opera-

tions by automatically providing a wide range of compati-

bility with shooting conditions that change as you move

between indoors and outdoors or between bright and dark

locations.

HDV and

are trademarks of Sony Corporation

(Excluding the CHU/CHE

model)

and Victor Company of Japan, Limited.

Model

(Accessories)

IEEE1394 Applicable

Lens Availability

Input

Model

•

24p mode shooting function

In HDV format, it records in 24p mode.

Lens

Microphone

GY-HD200U

GY-HD200CHU

Yes

U model

X See pages 10 and 33

X See page 33

It uses a 2:3:2:3 pulldown when recording to tape and con-

verts the images to 60 frames. Component output is con-

verted to 60 frames during playback as well.

24p DV format video uses a 2:3:2:3 pulldown (24p Mode).

A 2:3:3:2 pulldown (24p Advanced Mode) is also supported.

It can shoot with the same number of frames as movie

film.

•

ND filters for 1/4ND, 1/16ND provided

GY-HD200E

GY-HD200CHE

Yes

E model

IEEE1394 connector

IEEE1394 connector (6-pin) provided. Enables transfer of

digital data to other equipment provided with IEEE1394

connector, such as a non-linear editing system. (Power

cannot be supplied.)

GY-HD201E

GY-HD201CHE

Yes

Core Filter

For Viewfinder Cable

X See page 34

Clamp Filters ×4

For DC (×2)/Earphone/

IEEE1394 Cable

•

Tapes recorded in the DVCAM format can only be played

back (simple playback).

Recording in the DVCAM format is not possible.

•

1/3" bayonet type lens

X See pages 12, 36 and 63

Built-in color bars (ARIB (multi-format color bars), SMPTE/

EBU type)

This device is

recorder.

Videocassettes marked with the A symbol can be used.

HDV/DV video system format camera

DVCAM is a registered trademark of Sony Corporation.

•

60 Hz/50 Hz HD or HDTV signals

Supports both 60 Hz/50 Hz HD or HDTV signals.

You can select this in a menu screen.

•

Shutter speeds and menus can be selected using a dial,

making it very easy to use.

The following phenomena may occur when tapes recorded

on other units (including another GY-HD200U/GY-HD200E/

GY-HD201E) are recorded or played back on this device.

Variable scan shutter

There is no flicker when shooting computer screens and

other non-NTSC/PAL format screens.

Cross-convert video output

You can output converted video from the video output con-

nectors. You can select this in a menu screen.

SD memory card

X See page 34

•

The transient section between scenes recorded on other

units and those recorded on this device may appear dis-

turbed.

Digital noise may appear during playback due to track-

ing errors.

•

Slow shutter

Makes it possible to brightly shoot video of dark subjects

with little motion by accumulating the images.

•

Focus assist function

Enables easy and accurate focusing during shooting.

Backup recording function

Continuous extended recording is possible by connecting

to HDV/DV devices.

User buttons added

Enables you to switch camera settings instantly to suit the

shooting conditions.

This device records and plays back in the SP mode.

Recording or playback in the LP mode is not possible.

(In DV format)

Due to manufacturing dispersion of tapes, we recom-

mend not to record pictures within the first 2 to 3 min-

utes from the beginning of the tape.

Before recording important scenes, be sure to perform a

test recording and confirm that both video and audio are

recorded correctly.

Recorded video and audio contents are for private use.

Other use may infringe on the rights of copyright hold-

ers.

•

Time code reader/generator

The built-in time code reader/generator can be used to

record the time code and user’s bits.

Built-in large 3.5" color LCD display

In addition to displaying the camera image and the play-

back image, the LCD monitor shows the status screens,

menu screens for settings, and alarm indications.

•

Built-in monitor speaker for audio checking

The input audio can be monitored in recording or EE mode.

The playback sound can be monitored in the playback

mode. The speaker also outputs an alarm tone in case an

abnormal condition occurs in this device.

JVC cannot assume liabilities that may derive from the

impossibility of normal recording or playback of video or

audio due to malfunction of this device or the videocas-

sette.

Recording check function for convenient recording review

function

All product names in this manual are trademarks or regis-

tered trademarks of their respective companies.

Marks such as ™, ® and © are not used in this manual.

Attaching the Tripod Base (Optional) . . . . . . . . . . . . . . . . .35

AC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Charging the Built-in Battery. . . . . . . . . . . . . . . . . . . . .36

Battery Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . .37

Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . .37

Precautions for the Battery Operation. . . . . . . . . . . . . .38

Remaining Battery Power Display . . . . . . . . . . . . . . . .38

Operating Time with Battery Pack . . . . . . . . . . . . . . . .38

Precautions for the Battery Pack . . . . . . . . . . . . . . . . .38

Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Selecting the audio signal input . . . . . . . . . . . . . . . . . .55

Adjusting Audio during Recording . . . . . . . . . . . . . . . .55

Monitoring Audio during Recording . . . . . . . . . . . . . . .56

FILE MANAGE Menu Screen . . . . . . . . . . . . . . . . . . . . . .96

Displaying the FILE MANAGE menu screen . . . . . . . .96

Loading a menu settings file . . . . . . . . . . . . . . . . . . . . .96

Saving settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97

Resetting the menu settings to the factory settings . . .98

Initializing (formatting) an SD memory card . . . . . . . . .98

CONTENTS

SHOOTING OPERATION

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Basic Recording Operation . . . . . . . . . . . . . . . . . . . . . . . .57

If the Record-Standby Mode Continues . . . . . . . . . . . .58

Checking Recorded Contents in Record-Standby Mode

(Recording Check Function) . . . . . . . . . . . . . . . . . .58

HEADER REC Function . . . . . . . . . . . . . . . . . . . . . . . . . .59

FEATURES OF THE CAMERA SECTION

How to Use Skin Detail . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Outputting Color Bars . . . . . . . . . . . . . . . . . . . . . . . . . . .101

INTRODUCTION

Precautions for Proper Use . . . . . . . . . . . . . . . . . . . . . . . . .6

Routine and Periodical Maintenance . . . . . . . . . . . . . . . . . .7

Precautions for Use of Head Cleaning Tape . . . . . . . . . . . .7

Battery Pack to be Used . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Videocassette to be Used . . . . . . . . . . . . . . . . . . . . . . . . . .8

For recording and storing videotapes in the best

PREPARATIONS FOR OPERATION

PLAYBACK MODE

OTHERS

Turning the Power ON . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Turning the Power ON . . . . . . . . . . . . . . . . . . . . . . . . .39

Turning the Power OFF . . . . . . . . . . . . . . . . . . . . . . . .39

Loading/Unloading the Cassette . . . . . . . . . . . . . . . . . . . .40

Cassette Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Unloading the Cassette. . . . . . . . . . . . . . . . . . . . . . . . .40

Setting and Displaying the Date and Time . . . . . . . . . . . .41

Setting the Date and Time Style . . . . . . . . . . . . . . . . . .41

Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . .42

Displaying the Time and Date on the Screen . . . . . . . .42

Displaying Time Code . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Time code input entered the IEEE1394 connector

Playback Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Fast-Forward, Rewind . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Outputting Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Warnings and Responses . . . . . . . . . . . . . . . . . . . . . . . .102

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

How to Display the Hour Meter . . . . . . . . . . . . . . . . . . . .107

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108

EXTERNAL DIMENSIONS . . . . . . . . . . . . . . . . . . . . .109

condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Characteristic CCD Phenomena . . . . . . . . . . . . . . . . . . . . .9

USING EXTERNAL COMPONENTS

Connecting the Video Signal Cables . . . . . . . . . . . . . . . . .63

Connecting the IEEE1394 Cable . . . . . . . . . . . . . . . . .63

Dubbing with AV Devices . . . . . . . . . . . . . . . . . . . . . . . . .64

HDV/DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Backup Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Connect a Remote Control Unit (RM-LP55/RM-LP57) . . .68

CONTROLS, INDICATORS AND

CONNECTORS

ZOOM Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Front Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Rear Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

LCD Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Right Side Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Left Side Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Top Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Recording and Image Output Formats . . . . . . . . . . . . . . .20

Indications on the LCD Monitor and in the Viewfinder . . . .22

Status Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Status Screens in the Camera Mode . . . . . . . . . . . . . .23

Status Screen in VTR MODE . . . . . . . . . . . . . . . . . . . .28

Magnified Status Indications on the LCD Monitor. . . . .29

Auto White Balance Indication

(GY-HD200U/GY-HD201E only) . . . . . . . . . . . . . . .43

Presetting and Recording of Time Code . . . . . . . . . . . . . .44

Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Presetting time code data . . . . . . . . . . . . . . . . . . . . . . .45

Presetting user’s bit data . . . . . . . . . . . . . . . . . . . . . . .45

Zero-resetting the Time Code or User’s Bit Data . . . . .45

Presetting the Time Code from the LCD Screen . . . . . . . .46

Recording Time Codes in Continuation of Time Codes

Recorded on Tape . . . . . . . . . . . . . . . . . . . . . . . . .47

Playing Back Time Code . . . . . . . . . . . . . . . . . . . . . . . . . .47

Synchronizing with the Time Code of the IEEE1394

MENU SCREENS

Menu Screen Configuration . . . . . . . . . . . . . . . . . . . . . . . .70

Setting Menu Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

TOP MENU Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

VIDEO FORMAT[1/2] Menu Screen . . . . . . . . . . . . . . . . .74

VIDEO FORMAT[2/2] Menu Screen . . . . . . . . . . . . . . . . .76

CAMERA OPERATION Menu Screen . . . . . . . . . . . . . . . .77

CAMERA PROCESS[1/2] Menu Screen . . . . . . . . . . . . . .78

CAMERA PROCESS[2/2] Menu Screen . . . . . . . . . . . . . .79

ADVANCED PROCESS Menu Screen . . . . . . . . . . . . . . .80

COLOR MATRIX ADJUST Menu Screen . . . . . . . . . . . . .81

SKIN COLOR ADJUST Menu Screen . . . . . . . . . . . . . . . .81

WHITE BALANCE Menu Screen . . . . . . . . . . . . . . . . . . . .82

SWITCH MODE Menu Screen . . . . . . . . . . . . . . . . . . . . .83

AUDIO/MIC[1/2] Menu Screen . . . . . . . . . . . . . . . . . . . . .84

AUDIO/MIC[2/2] Menu Screen . . . . . . . . . . . . . . . . . . . . .85

LCD/VF[1/4] Menu Screen . . . . . . . . . . . . . . . . . . . . . . . .86

LCD/VF[2/4] Menu Screen . . . . . . . . . . . . . . . . . . . . . . . .87

LCD/VF[3/4] Menu Screen . . . . . . . . . . . . . . . . . . . . . . . .88

LCD/VF[4/4] Menu Screen . . . . . . . . . . . . . . . . . . . . . . . .89

TC/UB/CLOCK Menu Screen . . . . . . . . . . . . . . . . . . . . . .90

HEADER REC Menu Screen . . . . . . . . . . . . . . . . . . . . . . .91

TIME/DATE Menu Screen . . . . . . . . . . . . . . . . . . . . . . . . .92

OTHERS[1/2] Menu Screen . . . . . . . . . . . . . . . . . . . . . . .93

OTHERS[2/2] Menu Screen . . . . . . . . . . . . . . . . . . . . . . .94

(DV)-Connected Master Unit . . . . . . . . . . . . . . . . .48

Screen Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Viewfinder Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Back Focus Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .50

White Balance Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .51

White Balance Adjustment . . . . . . . . . . . . . . . . . . . . . .51

Full Auto White Balance (FAW) . . . . . . . . . . . . . . . . . .51

White Shading Adjustment . . . . . . . . . . . . . . . . . . . . . . . .52

(Camera mode only) . . . . . . . . . . . . . . . . . . . . . . . .30

Menu Setting Screen . . . . . . . . . . . . . . . . . . . . . . . . . .30

Alarm Message Display . . . . . . . . . . . . . . . . . . . . . . . .30

Safety Zone Indication (Camera mode only) . . . . . . . .30

Switching between the LCD Screen and Viewfinder

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

PREPARATIONS

SETTING AND ADJUSTMENTS BEFORE

SHOOTING

Basic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Attaching the Zoom Lens . . . . . . . . . . . . . . . . . . . . . . . . .33

Attaching the Microphone (Provided) . . . . . . . . . . . . . . . .33

How to Attach the Viewfinder . . . . . . . . . . . . . . . . . . . . . .33

Inserting an SD Memory Card . . . . . . . . . . . . . . . . . . . . . .34

Inserting an SD Memory Card . . . . . . . . . . . . . . . . . . .34

Taking out the SD memory card. . . . . . . . . . . . . . . . . .34

About SD Memory Cards . . . . . . . . . . . . . . . . . . . . . . .34

Setting the Video Format . . . . . . . . . . . . . . . . . . . . . . . . . .53

Setting the FRAME RATE Item. . . . . . . . . . . . . . . . . . .53

Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Screen Size (4:3/16:9) Mode Selection . . . . . . . . . . . . . . .54

Audio Input Signal Selection . . . . . . . . . . . . . . . . . . . . . . .55

Selecting the CH-2 channel input connector. . . . . . . . .55

INTRODUCTION

•

Do not insert an object other than a videocassette in the

cassette insertion slot. Be sure to close the cassette cover

when this device is not to be used for a long period.

Do not set the POWER switch to OFF or remove the

power cable during recording or playback. Otherwise the

tape may be damaged.

The sensitivity level of the provided microphone is set

lower than the reference input (–60 dBs) setting.

When this device is not in use, be sure to set the POWER

switch to OFF in order to reduce power consumption.

Cleaning the body: Wipe body with a dry, soft cloth. To

prevent deformation of the body, etc. and to avoid opera-

tion hazards, do not allow volatile liquids such as benzine

and thinner to touch the body, and do not wipe it with a

cloth soaked in such a liquid. When it is extremely dirty,

soak the cloth in a solution of neutral detergent, wipe the

body with it, and then use a clean cloth to remove the

detergent.

•

The maintenance contents vary depending on the operat-

ing environment and method. Therefore, the data in the

chart should be considered as a reference.

Precautions for Proper

Use

Routine and Periodical

Maintenance

Time management

The accumulated running time of this device can be con-

firmed with the hour meter display (which shows the accu-

mulated drum and fan motor running time). X See “How to

Display the Hour Meter” on page 107.

•

Supply voltage

This device incorporates precision mechanical parts, which

will collect dirt, wear out and deteriorate as this device is

used. After this device has been used for a long period even

in a normal environment, the heads, drums and tape trans-

port mechanisms also collect dirt. Especially, dust which

penetrates the inside of the VTR section during outdoor use

will promote the wear and deterioration of mechanical parts

by causing poor contact between tape and heads or failing to

maintain the video and audio quality at high levels. To pre-

vent wear and deterioration, clean the mechanical parts

using a head cleaning tape as routine maintenance. How-

ever, cleaning with a head cleaning tape alone is not enough

for cleaning the entire tape transport mechanism, so it is also

recommended to apply periodical maintenance (inspection)

to prevent the sudden occurrence of failure. As the replace-

ment, adjustment and servicing of parts require advanced

skill and equipment, please consult the person in charge of

professional video equipment at your nearest JVC-autho-

rized service agent.

Make sure that the power is between 11 V and 15 V DC. If

the power voltage is too low, abnormal color and

increased noise may occur.

Allowable ambient temperature and humidity

Be sure to use this device within the allowable tempera-

ture range of 0°C to 40°C and a relative humidity of 30% to

80%. Using this device at a temperature or humidity out-

side the allowable ranges could result not only in malfunc-

tion but the impact on the CCD elements could be serious

as small white spots may be generated.

Strong electromagnetic waves or magnetism

Noise may appear in the picture or audio and/or the colors

may be incorrect if the camera is used near a radio or tele-

vision transmitting antenna, in places where strong mag-

netic fields are generated by transformers, motors, etc., or

near devices emitting radio waves, such as transceivers or

cellular phones.

For consultations related to the maintenance planning or

cost, please contact the person in charge of professional

video equipment at your nearest JVC-authorized service

agent.

Precautions for Use of

Head Cleaning Tape

•

The camera may not show stable pictures in the period

immediately after the power is turned on, but this is not a

malfunction.

A sound occurs when the built-in head cleaner that runs

when you load or eject a videocassette operates, but this

is not a malfunction.

Please use cleaning tape produced by JVC.

Adhere to the following precautions when using the head

cleaning tape.

1.Insert the cleaning tape.

•

Use of wireless microphone near the camera

The LCD monitor and the viewfinder screen

Press the PLAY/STILL button after the cleaning tape is

fully loaded.

The tape runs for 10 seconds at a time in the PLAY

mode. (The tape stops automatically and then this device

enters the STOP mode.)

When

wireless microphone or wireless microphone

The LCD monitor and the viewfinder screen are manufac-

tured using high-precision technology. Black spots may

appear on the LCD monitor and the viewfinder screen, or

red, blue, green and/or white spots may not turn off. How-

ever, this is not a malfunction and these spots are not

recorded on the tape.

If you use this device continuously for a long period of

time, the characters displayed in the viewfinder may tem-

porarily remain on the screen. This is not recorded on the

tape. In addition, they are no longer displayed if you turn

the power off and then on again.

If you use this device in a cold location, the images may

appear to lag on the screen, but this is not a malfunction.

This is not recorded on the tape.

Do not insert fingers or foreign objects into the cassette

insertion slot as this may result in personal injury or dam-

age to the mechanism.

Head Cleaning

To maintain beautiful pictures and sound, be sure to use a

head cleaning tape to clean the head periodically.

X See “Precautions for Use of Head Cleaning Tape”. If

head cleaning is not performed periodically,

mosaic noise called block noise may appear in the picture

or sound may be interrupted.

tuner is used near the camera during recording, the tuner

could pick up noise.

Avoid using or placing this device in places;

•

subject to extreme heat or cold;

with excessive dirt or dust;

with high humidity or moisture;

subject to smoke or vapour such as near a cooking

stove;

type of

2.Do not use the tape more than four times at the most for

each cleaning.

•

„ Use the following chart as a guide for periodical head

•

subject to strong vibrations or on an unstable surface;

also do not leave this device for long hours in a parked

car under direct sunlight or near room heating equip-

ment.

cleaning.

Low

Room

High

•

Running

temperature

•

Do not leave this device where it is subject to radiation or

X-rays or where corrosive gasses occur.

Protect this device from being splashed with water (espe-

cially when shooting in the rain).

Protect this device from being wet when shooting on a

beach.

In addition, salt and sand may adhere to the camera body.

Be sure to clean the camera after use.

Protect this device against penetration of dust when using

it in a place subject to sandy dust.

Optical performance of lens

Due to the optical performance of the lens, color diver-

gence phenomena (magnification chromatic aberration)

may occur at the periphery of the image.

Operating envi- 0°C to 10°C

ronment

10°C to 35°C

35°C to 40°C

Block Noise

Yardstick

use of cleaning ery 5 hours

tape

for 1 to 2 times ev- 1 to 2 times ev- 1 to 2 times ev-

ery 20 to 30 ery 5 hours

hours

•

Please use cleaning tape produced by JVC. Do not use

head cleaning tapes other than specified.

X See “Precautions for Use of Head Cleaning Tape”

about how to use the head cleaning tape and precautions

for use of the head cleaning tape.

When dust adheres to the heads, the warning message

“HEAD CLEANING REQUIRED!” is displayed on the LCD

monitor, and in the viewfinder during playback and record-

ing check using the RET button on the lens section.

To prevent damage to the connectors, use this device with

the connector covers on when you are not using the video/

audio signal output connectors.

Note 1) When used in a low humidity environment, head

cleaning should be conducted at intervals half of

those given in the chart above.

Note 2) If an M-DV80 tape is used immediately after head

cleaning, the “HEAD CLEANING REQUIRED!”

indicator may remain on. In this case, let the tape

run as the indicator will turn off after the tape has

run for a while.

•

CAUTION

•

Do not point the lens or viewfinder directly at the sun or

other strong light source.

Periodical Maintenance

Contents : Check or replace the following mechanical parts

according to the running time.

•

Eye damage could result.

This is not a camera malfunction.

Note 3) Use the cleaning tape in the room temperature

(10°C to 35°C).

If the lens or viewfinder is left pointed at the sun, rays

may collect inside this device and cause damage or a

fire.

•

Noise may appear in the viewfinder when switching

between the playback picture and the EE picture.

Use this device in an upright position.

If placed on its side, heat release efficiency will deterio-

rate, adversely affecting the tape transport. Depending on

circumstances the tape may also be damaged.

Vibrations

Colors may fail to appear and/or the image and sound

may be disturbed during VTR playback in locations sub-

jected to strong vibrations.

Note 4) The cleaning tape case contains instructions for

use of the cleaning tape. However, some of these

instructions differ from the contents of this sheet.

When using the cleaning tape, please follow the

instructions of this sheet.

Note 5) If the “HEAD CLEANING REQUIRED!” does not

disappear after repeated head cleanings, the

recording tape may be abnormal. Avoid excessive

repeated use of the head cleaning tape.

Usage Time

500H 1000H 1500H 2000H

When carrying the camera, be sure to hold the carrying

handle. Holding the lens or viewfinder may result in

damage.

Drum assembly (includ-

ing heads)

Tape guides, rollers

Belt gears

•

Drive parts

G: Clean, check and adjust.

E: Clean and check. Replace as required.

F: Replace.

•

Precautions for transportation

Do not drop or hit this device against a hard object.

Remove the videocassette before transporting this device.

INTRODUCTION

eocassette, place this device in a tightly sealed vinyl bag,

and then move it to a new environment.

To ensure no condensation occurs, allow the temperature

of this device in the bag to reach that of the new environ-

ment before using it.

Battery Pack to be Used

For recording and storing

videotapes in the best con-

dition

Condensation

This device can use any of the following batteries. (Factory

setting)

U model: Anton Bauer battery

E model: IDX battery

•

If this device has been cooled down in a cold place and is

then carried to a warm place, the moisture contained in

the warm air may adhere to the head drum or tape guides

and be cooled into water droplets. This phenomenon is

referred to as condensation (dew). When this occurs, the

head drum and tape guides are covered with droplets

allowing the tape to be stuck to them, leading to tape dam-

age.

Characteristic CCD Phe-

nomena

Observe the following instructions for the best recording and

storage of videotapes.

Take care of the conditions of handling videotapes. It is

recommended that you record and store videotapes in the

environment below.

•

Recommended batteries

U model: Dionic 90 (Anton Bauer)

E model: Endura-7 (IDX)

Smear and Blooming

Storage

Due to the physical structure of a CCD it is possible to induce

vertical streaking (called “smear”) when shooting an

extremely bright light source. Another effect is the expansion

of light around a bright light or object (called “blooming”).

The CCD employed in this device is characterized by induc-

ing very little smear or blooming. Nevertheless, please take

note that smear or blooming may be induced when shooting

a bright light source.

•

Condensation occurs in the following cases:

Short period

(Up to 10

years)

Long period

(Over 10

years)

CAUTION

Recording

•

When this device is suddenly

Use only the recommended batteries.

If a heavy battery is used, the battery may fall out depend-

ing on the way the HD camera recorder is used.

Head drum

moved from

warm place.

cold place to

Temperature

Humidity

17°C to 25°C 15°C to 23°C 15°C to 19°C

•

When

room heater has just

30% to 70%

40% to 55%

25% to 35%

started or when this device is

exposed directly to cold air from

an air conditioner.

Hourly tempera-

ture change

Less than

10°C

Video tape

Smear

Hourly humidity

change

Less than

10%

•

When this device is placed in a

very humid place.

Vertical pale streaking appearing at high

luminous object

Videocassette to be Used

•

Do not leave the videotapes neglected for a long period. If

videotapes are left wound for a long period of time, it may

result in distortion of the tape. Also it may cause tape-to-

tape adhesion (known as blocking). It is recommended

that videotapes be unspooled and rewound once a year

for refreshing.

When tapes are not in use, store them in cases and on

end. Storage cases protect videotapes from humidity, dust

and ultraviolet light. Keep tapes in cases and do not store

them lying flat. When housed in a horizontal position, pres-

sure from other tapes can cause distortions and deforma-

tions of the tape edges.

High luminous object

(Electric light, sunlight, etc.)

Do not leave the videocassette inserted when moving the

camera under conditions where the temperature environ-

ment changes.

After moving this device, do not use until the internal parts

have stabilized.

Blooming

Blurring in highlight

Monitor screen

•

Use JVC’s videocassette tapes marked with the

symbol.

Mini DV videocassette : M-DV63HD

M-DV63PROHD

* Do not use M-DV80.

Moire or Aliasing

•

“CONDENSATION ON DRUM” is displayed on the LCD

monitor and in the viewfinder when condensation occurs

in this device.

Shooting stripes or fine patterns may cause a jagged effect

or a banding in fine mesh patterns.

•

Videocassettes cannot be used upside down.

Avoid storing a videocassette with its tape not being com-

pletely wound, as this may damage the tape. Rewind it to

the beginning before placing a cassette into storage.

Store videocassettes in a place with little humidity and

good ventilation where mould does not form.

After a videocassette tape has been used repeatedly, it

becomes unable to maintain full performance due to an

increase in noise caused by dropouts, etc. Do not continue

to use a dirty or damaged tape, as this will reduce the

rotary head life.

White dots

High temperatures can cause CCD sensor pixels to produce

the effect of white dots in the image. This condition is con-

spicuous especially when gain is applied.

This is a characteristic of the charged-coupled device (CCD).

As far as possible, use this device under conditions where

the temperature of this device does not increase.

•

Videocassette tapes with the A symbol are provided

with a switch on the back to prevent accidental erasure.

Slide the switch to SAVE to protect the required recording

in the tape from being overwritten.

Keep the power on until the warning message disappears.

If the power is turned off while the warning message is dis-

played, condensation may remain in the device even if the

warning message is not displayed. Wait until this device is

completely dry before using.

To record on the tape, slide the switch to REC.

Switch

•

Pay attention to condensation even before the condensa-

tion indication appears.

As condensation forms gradually, the condensation indica-

tion may not appear for the first 10-15 minutes after con-

densation has formed inside.

In an extremely cold place, the condensation could freeze

and turn into frost. In such a case, it takes an additional 2-

3 hours for the frost to first melt into condensation and

then to be dissolved.

•

To prevent condensation

When moving this device from one place to another where

the temperatures are greatly deferent, first remove the vid-

CONTROLS, INDICATORS AND CONNECTORS

6ZOOM servo control lever

6[ZEBRA] Zebra switch

To operate the servo zoom feature with this lever, set the

ZOOM knob b to “S”.

When this switch is ON, a zebra pattern is imposed on the

viewfinder or LCD areas having luminance levels in accor-

dance with the menu settings made for the video signal.

This pattern can be used as a reference for manual adjust-

ment of the lens iris. Zebra patterns are also displayed

during color bar display when this switch is set to ON.

ZOOM Lens

Front Section

•

Pressing the “W” section of this lever increases the

angle of the lens for a wider shooting angle.

Pressing the “T” section of this lever narrows the lens

angle perspective for telephoto shots.

The zoom lens is not provided with the GY-HD200CHU, GY-

HD200CHE or the GY-HD201CHE.

Pushing harder changes the speed of the zoom.

•

The default value is 70% - 80%. The luminance level

can be changed with the ZEBRA setting in the LCD/

VF[1/4] menu screen.

7IRIS mode switch

Th16 × 5.5BRMU

: Activates the auto iris feature.

: Allows manual iris control.

X See page 86.

While this switch is pressed to the SKIN AREA side, the

color tone areas specified with the SKIN COLOR ADJUST

item on the ADVANCED PROCESS menu are indicated in

the viewfinder. The switch returns to the OFF position

when released.

8Momentary auto iris button

When the IRIS mode switch 7 is at “M”, pushing this but-

ton activates the Auto Iris Function while it is held down

only.

X See “How to Use Skin Detail” on pages 99 and 100.

9[S] IRIS speed adjusting control

The Skin Detail color tone areas are not indicated while

the color bar or VTR playback picture is shown in the

viewfinder or on the LCD monitor.

For adjusting the iris operation speed.

MEMO

RET

If the speed becomes too fast, hunting may occur. To avoid

the phenomena described above, perform adjustment

again.

7[AWB] Auto white balance button

When the WHT.BAL switch c on page 15 is set to A or B

and you press this button, the white balance is automati-

cally adjusted.

0FILTER thread

It is not activated in preset, full auto shooting, full auto

white balance and color bar modes.

7 8

Protect the lens with a clear filter or UV filter by screwing

the filter onto the thread inside the lens hood from the

front.

X See “White Balance Adjustment” on page 51.

1Shoe

8Lens mounting ring/Lens lock lever

Hold the lens and use the lever to turn the ring anticlock-

wise to release lens.

Other filters can be used for various effects.

Makes it possible to mount separately sold lights and

accessories.

aZOOM servo connector

Connect an optional zoom servo unit here.

To mount lens make sure the lens guide pin fits well, and

then turn the ring clockwise until firm.

X See “Attaching the Zoom Lens” on page 33.

2Knob

b[ZOOM] ZOOM mode knob

This is the mounting knob for the microphone holder 3.

: Servo zoom mode. Allows operation by the zoom

servo control lever 6.

3Microphone holder

Makes it possible to attach the provided microphone or a

separately sold microphone.

: Manual zoom mode. Allows zoom control by the

zoom lever/ring 2.

X See “Attaching

the

Microphone

(Provided)”

on page 33.

cBACK FOCUS ring/fixing screw

For back focus adjustment only. Secure with the screw

knob after adjustment. X See “Back Focus Adjustment”

on page 50.

4Front tally lamp

1FOCUS ring

Manual focus ring.

This lamp lights up when this device enters the record

mode. It blinks during the transition to the record mode.

When the tape has run out, or the VTR enters the warning

mode, it blinks quickly.

2ZOOM lever/ring

dMacro focusing ring (for close-up shooting)

By rotating this ring in the direction of the arrow, close-up

shooting of very small objects becomes possible.

Normal focus adjustment and zooming are not available in

the macro mode.

To shoot images in the macro mode, set the focus ring 1

to the infinite position (f) and the zoom ring 2 to the max-

imum wide-angle position. To adjust the focus of the

macro image, rotate this ring in the direction of the arrow

until the object is focused.

This is the manual zoom ring equipped with a zoom lever.

To adjust the zoom manually, turn the zoom mode knob b

to position “M”.

•

Use the FRONT TALLY item on the OTHERS[1/2] menu

screen to select whether or not the lamp should light

and the lighting pattern.

3IRIS ring

X See page 93.

Manual iris ring. To activate the auto iris feature, set the

Iris Mode switch 7 to “A”.

5[LENS] Lens control connector

Connect 12-pin lens control cable from lens here.

4[VTR] VTR trigger button

To start/stop shooting.

No.

Function

Return switch

Function

Iris position

5[RET] Return video button

You can only monitor the return video signal from the VTR

on the viewfinder, LCD monitor and video signal connector

while this button is pressed.

When the camera control unit is connected, you can moni-

tor the return video signal on the viewfinder while this but-

ton is pressed. You cannot monitor on the LCD monitor or

video output terminal.

When you set the LENS RET item to “FOCUS ASSIST” in

the SWITCH MODE menu screen, you can use this button

as the FOCUS ASSIST button.

CAUTION

VTR trigger

GND

IRIS A/R INPUT

•

The back-focus knob is located close to the macro ring,

be careful not to mistake the back-focus knob for the

macro ring.

After the required operation, be sure to return the macro

focusing ring to the normal position.

EXTENDER position

Lens AUTO/MANU con- 10 ZOOM position

trol

•

IRIS control

+12V DC

–

X See “Attaching the Zoom Lens” on page 33.

X See “Back Focus Adjustment” on page 50.

X See page 83.

CONTROLS, INDICATORS AND CONNECTORS

„ Connecting the Earphone Cable

To reduce the emission of unwanted radio waves, be sure to

attach the provided clamp filter as shown in the figure below.

4[TC GENE.] Time code generator setting switch

Switch for setting the time code generator to preset mode

or regeneration mode. It is also used to select the time

code run mode when the preset mode is selected.

Rear Section

LCD Door

•

Attach the clamp filter as close to this device as possible,

as shown in the figure.

FREE

: The preset mode is selected, and the time

code run mode becomes the FREE run

mode.

Set to this position to record with the time

code or user’s bits set anew (preset). In this

setting, the time code always operates in the

run mode.

Earphone cable

Clamp filter

LCD BRIGHT

CAM/VTR

If this setting is used when recording

scenes one after another, the time codes

become discontinuous at the transition

points between scenes.

AUDIO SELECT

CH-2

DISPLAY

GENE.

CH-1

FREE

AUTO

MANU

3Shoulder belt hooks

REC

REGEN

REC

: The preset mode is selected, and the time

code run mode becomes the REC run mode.

Set to this position to record with the time

code or user’s bits set anew (preset). The

time code operates in the run mode during

recording only. If this setting is used when

recording scenes one after another, the time

codes are recorded as continuous time

codes.

: Regeneration mode, in which this device

reads existing time codes on the tape and

records time codes in continuation of the

existing ones. Set to this position when you

want to add additional time codes to time

codes already recorded on the tape.

Allows you to attach a separately sold shoulder belt.

4LCD monitor

Shows a color camera image or the VTR playback picture.

It is also used for displaying the following:

•

Menu Setting screens

Characters showing the whether this device is set to

shooting mode or VTR playback mode

Date and time and time code

Audio level meter

1[LCD BRIGHT +/–] LCD brightness +/– button

This button is for adjusting the brightness of the LCD mon-

itor display.

•

Pushing the button in the + direction makes the monitor

brighter.

Pushing the button in the – direction makes the monitor

darker.

Pushing the +/– buttons simultaneously returns the set-

ting to the standard setting.

REGEN

Warning indications, etc.

1Back tally lamp

X See page 22.

This lamp lights up when this device enters the record

mode. It blinks during the transition to the record mode.

When the tape has run out, or the VTR enters the warning

mode, it blinks quickly.

•

Use the BACK TALLY item on the OTHERS[1/2] menu

screen to select whether or not the lamp should light

and the lighting pattern.

2[CH-1/CH-2 AUDIO SELECT] CH-1/CH-2 audio selector

switch

MEMO

Selects the method of adjusting the CH-1 and CH-2 audio

channel audio levels.

Preset of time code and user’s bits is performed on the TC/

UB/CLOCK menu.

X See page 44.

X See page 93.

2[PHONES] Earphone jack

AUTO

: The audio level is automatically adjusted

according to the input level. When excessive

audio is input, the limiter works to suppress

the audio level.

This is a stereo mini-jack for connecting an earphone for

audio monitoring. Plug in an earphone or headphone with

a 3.5 mm diameter plug. The earphone can also be used

to monitor alarm tones in accordance with the circum-

stances.

The audio channel to be output is selected with the AUDIO

MONITOR item on the AUDIO/MIC[2/2] menu screen and

MONITOR SELECT switch d on page 19.

X See “TC/UB/CLOCK Menu Screen” on page 90.

5[CAM/VTR] Camera/VTR mode switch button

Each time you press this button, the mode switches

between camera mode and VTR mode.

When you do this, the VTR indicator f on page 19 dis-

plays the following statuses.

The “AUTO” LED in the CH-1/CH-2 AUDIO

LEVEL area f on page 15 lights.

MANU

: Allows you to adjust the audio levels using

the CH-1/CH-2 AUDIO LEVEL volume con-

trols f on page 15.

While the mode is being switched: Flashing

The audio output level is adjusted with the Audio monitor

volume control 3 on page 14.

Set AUDIO LIMITER on the AUDIO/MIC[1/2]

menu screen to use limiter functions when

excessive audio is input.

In VTR mode

: Lit

In camera mode

: Off

•

Select the Camera mode to record the camera image.

Select the VTR mode to playback VTR or to input the

HDV/DV signal from the IEEE1394 connector on

MEMO

X See “AUDIO LIMITER” on page 84.

•

The volume of the alarm sound is set with the ALARM

VR LEVEL item on the OTHERS[1/2] menu screen.

When using a stereotype jack and stereo sound should

be output, the following setting should be performed.

Set the MONITOR SELECT switch d on page 19 to

BOTH.

3[TC DISPLAY] TC/UB display switch

Selects the contents displayed on the TC counter of the

LCD monitor or in the viewfinder. (This switch works when

the TC/UB item on the LCD/VF[3/4] menu screen is set to

ON.)

page 16. (HDV/DV signal input is possible with the

GYHD200U/GY-HD201E.)

•

When the power is turned on, the mode becomes the

Camera mode.

: Set to this position to display time code values.

Set the AUDIO MONITOR item on the AUDIO/MIC[2/2]

menu screen to STEREO.

UB : Set to this position to display the user’s bits values.

CONTROLS, INDICATORS AND CONNECTORS

X See “LCD/VF[1/4] Menu Screen” on page 86.

7Clamp

Attach the cable from the viewfinder here.

a[STATUS] Status/Menu button

d[POWER] Power ON/OFF switch

Switch that turns the power ON/OFF.

When the power is OFF, “POFF” is displayed in the LCD

monitor or viewfinder.

•

Pressing this button in the normal screen mode (condi-

tion in which the menu screen is not shown) displays a

status screen in the viewfinder or on the LCD monitor.

The displayed status screen changes each time the but-

ton is pressed.

Right Side Section

8[USER1/2/3] User buttons

You can assign camera functions to the USER1 - 3 but-

tons.

Use them to switch shooting conditions depending upon

the subject.

Wait at least 5 seconds if you need to turn the power on

again.

X See “Status Screens” on page 22.

e[REC] REC trigger button (start/stop recording)

Start and stop recording using this button.

(This works together with the REC trigger button on the

top and the lens VTR trigger button.)

When “SPLIT” is set for the 1394 REC TRIGGER item on

the OTHERS[2/2] menu screen, this button becomes the

start/stop recording button for an external device.

X See page 94.

•

Pressing this button for more than 1 second in the nor-

mal screen mode displays the menu screen in the view-

finder or on the LCD monitor. Pressing this button while

the menu screen is displayed in the viewfinder or on the

LCD monitor makes the menu screen disappear.

X See “Setting Menu Screens” on page 72.

Set them using the USER1

MODE menu screen.

X See page 83.

items in the SWITCH

Use this button to preset the time code.

X See page 46.

b[GAIN] Sensitivity selector switch

Electronically boosts the light sensitivity when there is

insufficient illumination on the subject.

The boosting level differs depending on the switch position

as follows:

VF BRIGHT

MEMO

X See “Backup Recording” on page 67.

USER

•

The USER buttons work together with the menu settings.

When a menu screen is being displayed, they also func-

tion as menu operation buttons. X See “Setting Menu

Screens” on page 72.

f[CH-1/CH-2 AUDIO LEVEL] CH-1/CH-2 Audio level con-

trols and AUTO LED

Allow you to adjust the audio level for the CH-1 and CH-2

audio channels.

ND FILTER

(Factory presets)

STATUS

WHT.BAL

: 0 dB (no boosting is applied)

AUTO

CH-1

AUTO

AUDIO

•

To use these controls, set the CH-1/CH-2 AUDIO

SELECT switch 2 on page 13 to “MANU”.

When the FULL AUTO switch g on page 19 or the CH-

1/CH-2 AUDIO SELECT switch 2 on page 13 is set to

“AUTO”, “AUTO” LED lights. (The audio level controls

do not work.)

LEVEL

CH-2

M : 9 dB (boosted to approximately 3 times the original)

H : 18 dB (boosted to approximately 8 times the original)

OFF

9[SHUTTER] Shutter/Menu dial

•

POWER

REC

•

Every time this dial is pressed while in the normal

screen mode (when the menu screen is not displayed),

the shutter speed switches between on/off.

•

The boosting level for each switch position can be

changed with the SWITCH MODE menu screen.

X See page 83.

•

When this dial is turned 1 click up or down in the normal

screen mode, the shutter speed indicator is shown for

about 3 seconds on the LCD monitor or in the view-

finder. The shutter speed is changed when this dial is

turned while the shutter speed indicator is shown.

X See page 83.

The more the boosting level is increased, the more the

resulting image will be noisy.

1Monitoring speaker (Cheek pad)

g[HDV/DV LED]

•

In the Camera mode, the input sound can be EE moni-

tored.

•

In camera mode, this lights according to the setting for

•

When the FULL AUTO switch g on page 19 is “ON”,

this is fixed at “ALC”.

the video format being shot.

In the VTR mode, the speaker outputs the VTR play-

back sound. In the VTR mode, the HDV/DV input sound

can be EE monitored. (HDV/DV signal input is possible

with the GY-HD200U/GY-HD201E.)

The sound to be output is selected with the MONITOR

SELECT switch d on page 19.

•

In VTR mode, it lights according to the video format

being recorded on tape or the IEEE1394 input video for-

mat.

c[WHT.BAL] White balance switch

Three white balance modes are selectable with this

switch.

•

When this dial turned upward or downward while the

menu screen is displayed, the cursor (K) also moves

upward or downward to allow selection of items in the

menu. To change the setting value of the item, press

this dial. When the setting value starts blinking, turn this

dial upward or downward to change the setting.

X See “Setting Menu Screens” on page 72.

HDV

: Lights when the format is HDV.

: Lights when the format is DV.

: Switch into white balance mode memorized

in B. If white balance is performed with the

switch in this position, it will be memorized

into B.

•

The sound level is adjusted with the MONITOR sound

level volume 3. This speaker also outputs various

warning sounds superimposed on other sound.

HDV/DV : Turns off when the format is 1080i.

MEMO

X See “Alarm Sound” on page 105.

: Switch into white balance mode memorized

in A. If white balance is performed with the

switch in this position, it will be memorized

into A.

•

During

system error, HDV/DV flash alternately.

2Cheek pad set screw

Screw for adjusting the height of the cheek pad.

0[ND FILTER] ND filter switch

Switches the built-in ND filter.

X See page 104.

•

Select whether or not to have this light in the FORMAT

LED item on the OTHERS[1/2] menu screen.

X See page 93.

3[MONITOR] Audio monitor volume control

Adjusts the volume of the monitoring loudspeaker and ear-

phone.

OFF : Turns the filter OFF (FILTER OFF)

PRST

: Switch into white balance mode (3200K or

Cuts the light intensity to approximately 1/4. (1/4ND)

Cuts the light intensity to approximately 1/16. (1/16ND)

(PRESET) 5600K) set in PRESET TEMP. item on the

CAMERA OPERATION menu screen.

X See page 77.

4[VF BRIGHT] Viewfinder brightness adjustment

To adjust the brightness of the viewfinder.

X See page 49.

When you change this switch, the type of the new ND filter

is displayed in the LCD monitor or viewfinder.

hLCD door lock and release knob

To open the LCD door, move this knob on the direction

toward the rear section.

FAW (Full Auto White Balance) mode can be set to A, B or

PRESET with the SWITCH MODE menu screen.

X See page 83.

In the FAW mode, video color temperatures are constantly

sampled for automatic adjustment to a proper white bal-

ance.

CAUTION

5[PEAKING] Contour adjustment

To adjust the contours of the LCD monitor and viewfinder

image.

iLCD door

LCD monitor door.

If you switch the ND filter while shooting is in progress, the

picture may be disturbed or noise may occur in the audio.

X See “Camera Settings” on page 54.

The LCD monitor is located on the inner side of the door.

The LCD monitor can be viewed when this door is opened.

The door can be turned to change the orientation of the

LCD monitor, and it can be rotated so that it can be

accommodated in the main body of the camera.

X See page 49.

When the Focus Assist function is running, this control

does not operate.

X See page 49.

•

When the FULL AUTO switch g on page 19 is “ON”,

this is fixed at “FAW”.

6[FOCUS ASSIST] Focus assist button

When you press this button during shooting, the area of

focus is displayed in blue, red or green, making it easy to

focus accurately.

MEMO

Fine-tune red and blue to match the white adjusted in auto

white balance in WHITE PAINT<R>/ on the WHITE

BALANCE menu screen. (Available only when this switch is

set to A or B.)

MEMO

•

When FOCUS ASSIST on the LCD/VF[1/4] menu screen is

set to ACCU-FOCUS and this button is pressed, ACCU

FOCUS functions with FOCUS ASSIST. This makes depth of

field shallower, making it easier to focus.

X See “WHITE BALANCE Menu Screen” on page 82.

•

This button has the same function as the FOCUS

ASSIST button 7 in the Top Section.

CONTROLS, INDICATORS AND CONNECTORS

•

Set the [AUDIO INPUT] switch

device to be connected.

Set the CH-2 audio input connector using the [CH-2

INPUT] switch 2.

according to the

Left Side Section

The CH-2 audio from the set connector is recorded.

5Shoulder pad slide button

Button to adjust the position of the shoulder pad.

When you press this button, you can move the position of

the shoulder pad 6 forward or backward.

6Shoulder pad

7Cassette cover

Sliding the EJECT switch a on page 18 located on the

top section opens this cover to allow insertion or removal

of the videocassette.

CAUTION

To prevent foreign objects from entering the internal parts of

the VTR unit, do not leave this device with the cover open

for extended periods of time.

a[IEEE1394] IEEE1394 switch

Set according to the image format of the input/output sig-

nal and playback signal of the IEEE1394 terminal.

HDV : Set to this for HDV format.

1Viewfinder connector (6-pin)

Connect the cable from the viewfinder here.

8[VIDEO OUT] Video output terminal (RCA)

This is a terminal for composite video signal output.

2[CH-2 INPUT] CH-2 audio input connector selector

switch

Selects the CH-2 audio input connector.

: Set to this for DV format.

•

Select whether or not to output a signal with setup in

SET UP on the VIDEO FORMAT[2/2] menu screen.

(Only for U model)

b[Y/PB/PR] Component Y/PB/PR signal output terminal

(BNC × 3)

Outputs analog component (Y/PB/PR) signals.

INPUT1

: Inputs the audio from the INPUT1 connector

4 into CH-2.

•

Set ANALOG OUT CHAR. item on the OTHERS[1/2]

menu screen to ON to output menu setting screens and

warnings from this terminal.

•

Select whether or not to add setup signals to DV format

signals in SET UP item on the VIDEO FORMAT[2/2]

menu screen. (Only for U model)

INPUT2

: Inputs the audio from the INPUT2 connector

4 into CH-2.

9[AUDIO OUTPUT CH-1/CH-2] Audio output connector

(RCA)

Output connector for audio signals.

•

Set ANALOG OUT CHAR. item on the OTHERS[1/2]

menu screen to ON to output menu setting screens and

warnings from this terminal.

MEMO

The audio from the INPUT1 connector is also input into

CH-1 regardless of the setting.

•

Outputs the input audio signal in the Camera mode.

Outputs the playback audio signal in the VTR mode.

When a HDV/DV signal (IEEE1394) is input, the EE

sound of the input audio signal is output in the VTR

mode. (HDV/DV signal input is possible with the

GYHD200U/GY-HD201E.)

c[REMOTE] REMOTE terminal (Round 6-pin)

Some functions of this camera can be controlled exter-

nally.

Connect to a remote control unit (RM-LP55/RM-LP57).

X See “Connect a Remote Control Unit (RM-LP55/RM-

LP57)” on page 68.

3[AUDIO INPUT] Audio input signal selector switch

This switch is used to select the input sound signal from

INPUT1 or INPUT2 connector.

LINE

: Set to this position when connected to audio

equipment, etc. The reference input level is

+4 dBs.

MEMO

d[DC INPUT] DC input terminal (XLR 4-pin)

This is the 12V DC power input terminal. Connect to the

AC adapter.

When a battery is installed and a cable is connected to this

terminal, power supply from the battery stops and power is

supplied by this terminal.

Alarm sound is not output.

MIC

: Set to this position when the dynamic micro-

phone is connected.

0[IEEE1394] IEEE1394 connector (6-pin)

MIC+48V : Set to this position when

requiring +48 power supply (phantom

microphone, etc.) is connected.

microphone

Using an IEEE1394 cable (optional), a digital video com-

ponent with IEEE1394 connector can be connected here.

X See “Connecting the IEEE1394 Cable” on page 63.

X See “HDV/DV Dubbing” on page 65.

CAUTION

When connecting a component that does not require +48 V

power supply, make sure that the switch is not set to

MIC+48V before the component is connected.

When connecting the IEEE1394 cable, confirm that the

connector is facing the right direction before inserting.

X See page 63.

MEMO

You can select the normal input level for MIC and MIC+48V

in the INPUT1, 2 MIC REF. item on the AUDIO/MIC[1/2]

menu screen.

Put the covers on the connectors when you are not using

them.

X See page 84.

4[INPUT1/INPUT2] INPUT1/INPUT2 audio input connec-

tors

These are audio input connectors for connecting to an

external audio device or microphone.

CONTROLS, INDICATORS AND CONNECTORS

MEMO

d[MONITOR SELECT] Audio monitor selector switch

This switch is used to select the monitor sound output and

playback sound output from the monitoring speaker 1 on

page 14 or the PHONES jack 2 on page 12.

•

When you release FAS mode, all of the settings return

to their previous modes.

•

When FOCUS ASSIST on the LCD/VF[1/4] menu screen

Top Section

is set to ACCU-FOCUS and this button is pressed,

ACCU FOCUS functions with FOCUS ASSIST. This

makes depth of field shallower, making it easier to focus.

This button has the same function as the FOCUS

ASSIST button 6 in the Right Side Section.

CAUTION

When the power is turned on while the camera is in the

FAS mode, it takes about 10 seconds before the automatic

adjustment of FAS is completed.

All of the previous setting contents are recalled when the

FAS mode is cancelled.

CH-1 : The CH-1 channel audio is output.

BOTH : CH-1 and CH-2 channel audio are output mixed.

When this setting is selected, the menu screen

can be used to select whether the mixed sound

or stereo sound should be output via the

PHONES jack. (AUDIO MONITOR item on the

AUDIO/MIC[2/2] menu screen)

•

X See “LCD/VF[1/4] Menu Screen” on page 86.

8[REC] REC trigger button (start/stop recording)

Start and stop recording using this button.

(This works together with the REC trigger button on the

right panel and the lens VTR trigger button.)

h[STOP] Stop button

Press to enter the stop mode.

When AUDIO MONITOR item on the AUDIO/

MIC[2/2] menu screen is set to “STEREO”, only

the audio of CH-1 is output from the monitoring

speaker.

i[REW] Rewind button

Press this button to rewind the tape.

•

9[REC LOCK] REC LOCK switch

Pressing this button in the stop or fast forward mode ini-

tiates the rewind mode. (Only for VTR mode)

Pressing this button during playback, still picture play-

back or forward search initiates reverse search.

Slide this switch in the direction of the arrow to lock the

[REC] trigger button 8. Use this to prevent unwanted

recording.

(The REC trigger button on the right panel and the lens

VTR trigger button are not locked.)

CH-2 : The CH-2 channel audio is output.

•

X See “Outputting Audio” on page 62.

X See “AUDIO/MIC[2/2] Menu Screen” on page 85.

j[PLAY/STILL] Play/still button

CAUTION

Press to start playback. Press to enter the still picture

mode during playback, in the stop mode or in the search

mode.

Depending on the ambient temperature, if still image play-

back mode continues for between 30 seconds and 3 min-

utes, it stops automatically. (Tape protect mode)

During still picture playback and search mode, press this

button to return to the normal playback mode.

0SD memory card cover

When you open this cover, you can insert and remove the

SD memory card.

X See “Inserting an SD Memory Card” on page 34.

When an SD memory card is loaded

Make sure to move switches all the way. Do not leave a

switch stopped in a midway position. Noise will be gener-

ated and operation irregularities will occur.

e[DISPLAY] Display button

•

You can save, call up and reset the menu settings on

this device.

•

When LCD+VF in the LCD/VF[4/4] menu display is set

to OFF, press the DISPLAY button for 2 seconds to

switch between the LCD screen and the viewfinder

screen.

•

You can initialize (format) an SD memory card.

If the auto tracking is active at the moment the play

mode is entered, the playback video will be interfered

with digital noise.

X See “FILE MANAGE Menu Screen” on page 96.

a[EJECT] Eject switch and LED

Slide this switch to the side to insert or eject a videocas-

sette tape.

•

When LCD+VF in the LCD/VF[4/4] menu display is set

to ON, press the DISPLAY button for

seconds to

k[FF] Fast forward button

Press this button to fast forward the tape.

•

switch the LCD screen ON and OFF. Press the DIS-

PLAY button briefly to change the display mode for the

LCD screen as follows.

The LED lights while ejecting is in progress.

Pressing this button in the stop or rewind mode initiates

the fast forward mode. (Only for VTR mode)

Pressing this button during playback, still picture play-

back or reverse search initiates forward search.

MEMO

Only image displayed

Characters shown enlarged

•

It takes

few seconds before the videocassette is

ejected. Do not close the cassette cover during the eject

operation.

Image and characters displayed

lScrew holes for mounting accessories

1Viewfinder

Displays the camera image and the playback picture.

•

Do not touch the cassette insertion slot or cassette dur-

ing the eject operation. This could result in damage.

X See “Magnified Status Indications on the LCD Monitor”

on page 29.

You can mount lights and other accessories.

2Eyepiece

f[VTR] VTR indicator

Ensures that ambient light does not reach the viewfinder

screen or falls into the eye of the cameraman.

bOperation cover

Open this cover when operating in the playback mode.

Otherwise, keep this cover closed.

This indicator lights when the camera is in the VTR mode.

To perform VTR playback or to input the HDV/DV signal

from the IEEE1394 connector 0 on page 16, press the

CAM/VTR button 5 on page 13 to turn on this indicator.

It flashes when the mode is being changed.

(HDV/DV signal input is possible with the GY-HD200U,

GY-HD201E.)

3Eyepiece focus ring

You can adjust the focus by turning this ring.

This cover can be opened by sliding it to the side.

4Eyepiece mounting ring

You can adjust the position of the eyepiece forward or

backward by loosening this ring.

MEMO

When the STOP button h is pressed in the Camera mode

to set the VTR operation mode indicator to indicate STOP,

playback operations become possible.

g[FULL AUTO] Full auto shooting (FAS) switch

This is the ON/OFF switch for FAS mode.

5Slide mounting ring

You can adjust the position of the viewfinder left or right by

loosening this ring.

•

During FAS mode, “FAS” is displayed on the LCD moni-

tor or the viewfinder.

cBattery adapter

Attach the battery.

U model: Anton Bauer battery

E model: IDX battery

X See “Battery Operation” on page 37.

6Clamp

Attach the microphone cable here.

•

FAS mode works together with the auto iris and auto

level control (ALC) modes and automatically adjusts to

the optimal video signal level and white balance.

You can select automatic adjustment mode or manual

adjustment mode for audio recording level.

X See “AUDIO/MIC[2/2] Menu Screen” on page 85.

Even if there are color bars, this automatically sets to

camera video.

Auto iris mode operates even if the lens iris mode

switch is set to the manual position.

The gain changes continuously until it reaches the max-

imum ALC MAX setting, and the shutter speed also

changes continuously.

7[FOCUS ASSIST] Focus assist button

When you press this button during shooting, the area of

focus is displayed in blue, red or green, making it easy to

focus accurately.

•

CONTROLS, INDICATORS AND CONNECTORS

„ When Recording HDV or DV Images from the IEEE1394 Terminal (Only with the GY-HD200U and GY-HD201E)

Component Out

Recording and Image Out-

put Formats

Recording

(IEEE1394 In)

[HDV PB OUTPUT] menu item

Rec on Tape

Composite Out

NATIVE

720P

1080I

1080/60i

1080/50i

1080/60i

N/A

NTSC

480/60i

N/A

PAL

N/A

720/60p

720/30p

720/50p

720/25p

720/24p

480/60p

576/50p

480/60i

N/A

480/60i

576/50i

480/60i

N/A

720/60p

N/A

This device supports HDV and DV image formats. This device also has various output terminals. (Composite, analog component,

IEEE1394)

During recording and playback, image formats from each of the output terminals are as shown in the table below.

576/50i

N/A

HDV

720/50p

720/60p

N/A

480/60i

N/A

Notes about the table

(Shaded): Indicates the setting item in the VIDEO FORMAT menu screen.

N/A: Terminal is not available.

N/A

: Same format as the left.

U model

480/60i(24p)

576/50i

„ When recording camera images

Recording (Shooting)

E model

576/50i(25p)

Component Out

(EE Out)

Composite Out

(EE Out)

Rec on Tape

IEEE1394 Out

[REC] menu item

HDV-HD60P

HDV-HD30P

HDV-HD50P

HDV-HD25P

HDV-HD24P

Format

720/60p

720/30p

720/50p

720/25p

720/24p

480/60i

MEMO

720/60p

480/60i

576/50i

480/60i

Synchronize the setting for FRAME RATE on the VIDEO FORMAT menu screen with the frame rate of the IEEE1394 input signal.

(HDV)

720/50p

720/60p

DV-60I

DV-24P

U model only

E model only

480/60i(24p)

DV-24PA 480/60i(24p)

DV-50I

576/50i

DV-25P

576/50i(25p)

[1080I CAMERA]

menu item

Frame rate

Rec on Tape

IEEE1394 Out

Component Out

Composite Out

60/30

50/25

N/A

1080/60i

1080/50i

480/60i

576/50i

„ In PLAY mode

Component Out

Playback

IEEE1394 Out

[HDV PB OUTPUT] menu item

Composite Out

NATIVE

720P

1080I

1080/60i

1080/50i

1080/60i

N/A

NTSC

480/60i

N/A

PAL

N/A

720/60p

720/30p

720/50p

720/25p

720/24p

480/60p

576/50p

N/A

480/60i

576/50i

480/60i

N/A

720/60p

N/A

576/50i

N/A

HDV

720/50p

720/60p

N/A

480/60i

N/A

480/60i

U model

E model

480/60i(24p)

576/50i

576/50i(25p)

MEMO

Synchronize the setting for FRAME RATE in the VIDEO FORMAT menu screen with the frame rate of the playback signal.

CONTROLS, INDICATORS AND CONNECTORS

The contents of the status display are divided into those for

the Camera mode and those for the VTR mode.

Status Screens in the Camera Mode

Indications on the LCD

Monitor and in the View-

finder

•

Each time the STATUS button is pressed in the Camera

mode, one of 5 status screens is displayed. (STATUS 0, 1,

2, 3, 4)

•

One type of screen is displayed in the VTR mode.

CAMERA MODE (display example)

266S DD

In addition to showing the EE image and the playback pic-

ture, the LCD monitor and viewfinder are also used for the

following character displays.

To show characters on the LCD monitor, press the DISPLAY

button briefly.

STATUS 0

STATUS 1

STATUS 0 Screen

STATUS 0

Event Indication

When the Gain or Shutter Speed is changed manually, the setting condition is displayed for about 3 seconds at the time the

change is made.

•

Set the shutter display method to seconds or angle in SHUTTER DISP. on the LCD/VF[3/4] menu screen. (Only when

frame rate is 24p or 25p mode)

DISPLAY button

STATUS 2

STATUS 4

„ Status screens (screens for checking the current cam-

•

VTR MODE

(display example)

Setting Status

Contents of Indications

GAIN 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 15 dB, 18 dB

era settings)

Gain value was changed

„ Auto white display (only displayed in the Camera

mode)

„ Menu setting screens

„ Alarm message display

„ Safety zone display (only displayed in the Camera

mode)

Gain value reached the ALC

FULL AUTO was turned ON/OFF

ZEBRA was turned ON/OFF

Shutter speed value was changed

GAIN ALC

FULL AUTO ON, FULL AUTO OFF

ZEBRA ON, ZEBRA OFF

SHUTTER 1/6, 1/6.25, 1/7.5, 1/12, 1/12.5, 1/15, 1/24, 1/25, 1/30, 1/48, 1/50, 1/60, 1/100, 1/120,

1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000

(When SHUTTER DISP. is set to SEC)

Variable shutter speed value was changed

(When SHUTTER DISP. is set to SEC)

V. SHUTTER 1/24.01 to 1/10489.5

MEMO

When ANALOG OUT CHAR. on the OTHERS[1/2] menu

screen is ON, characters are also shown on images from

the Y/PB/PR OUT and VIDEO OUT terminals.

STATUS 3

STATUS

Shutter was turned OFF

SHUTTER OFF [1/**]

Shutter speed value was changed

(When SHUTTER DISP. is set to DEG)

SHUTTER 360.0°, 180.0°, 172.8°, 150.0°, 144.0°, 135.0°, 120.0°, 105.0°, 90.0°, 75.0°, 60.0°,

45.0°, 30.0°, 22.5°, 11.2°

MEMO

Variable shutter speed value was changed

(When SHUTTER DISP. is set to DEG)

24p: 0.82° to 359.4°

25p: 0.85° to 359.4°

•

When the STATUS button is pressed for 1 second or

longer, the menu setting screen is displayed.

To display the Status screen while the menu setting

screen is displayed, press the STATUS button to return

to the normal screen.

You can switch between the LCD monitor and the view-

finder by holding down the DISPLAY button for about 2

seconds. (When the LCD+VF item on the LCD/VF[4/4]

menu screen is set to OFF.)

White balance value was changed

(Example)

WHITE BAL A [3200K]

Status Screens

Numeric value: Any of 2300, 2500, 2800, 3000, 3200, 3400, 3700, 4300, 5200, 5600, 6500,

8000

Press the STATUS button while normal screen is displayed

to show one of the status screens.

•

FILTER value was changed

FILTER OFF, FILTER ND 1 [1/4ND], FILTER ND 2 [1/16ND]

AE LEVEL –3, –2, –1, NORMAL, +1, +2, +3

AE LEVEL value was changed

BLACK gain value was changed

BLACK NORMAL

BLACK STRETCH 1, 2, 3, 4, 5

BLACK COMPRESS 1, 2, 3, 4, 5

USER

SHUTTER

*2 *3

PRESET TEMP. value was changed

WHITE BAL PRST [3200K], WHITE BAL PRST [5600K]

HEADER REC

ND FILTER

HEADER REC is running

FOCUS ASSIST was turned ON/OFF

Time code was set to zero reset

REC LOCK switch was turned ON/OFF

FOCUS ASSIST ON, FOCUS ASSIST OFF

TC ZERO PRESET X See page 45.

STATUS

REC SWITCH LOCKED, REC SWITCH UNLOCKED X See page 18, 9 REC LOCK switch.

A REC command was sent from the IEEE1394 TRIGGER TO HDV, TRIGGER TO DV

connector

STATUS button

CONTROLS, INDICATORS AND CONNECTORS

Indications on the LCD Monitor

and in the Viewfinder (Cont’d)

Setting Status

Contents of Indications

FF/REW button was pressed in CAMERA SWITCH TO VTR MODE

mode

REC/VTR trigger button was pressed when 1080I REC INVALID

1080I CAMERA in the VIDEO FORMAT[1/2]

menu screen was set to ON

Other Displays

X See “FILE MANAGE Menu Screen” on pages 96-98.

X See “Warnings and Responses” on page 102.

STATUS 1 Screen

The range for the shutter speed differs depending on the video format setting. X See page 83.

Displayed if functions were assigned to the USER1 - 3 buttons. X See page 83.

Displayed when the [WHT.BAL] white balance selector switch c on page 15 is set to PRST (PRESET).

“ ** ” depends on the video format.

STATUS 1

In addition to the information on the STATUS 0 screen, this screen displays the following items.

No.

Item

Contents

No.

Item

Contents

VIDEO FORMAT display

Displays the currently selected video format.

Allows you to select the REC item on the VIDEO FORMAT[1/2] menu screen. X See page 74.

You can switch this display ON/OFF using the VIDEO FORMAT item on the LCD/VF[3/4] menu screen.

X See page 88.

VTR mode indication

STBY : In record standby mode (record-pause mode)

REC : During recording

PLAY : During playback

: During fast forward

Time Code (TC)/User’s Bits Indicates the time code (h:m:s:frame) or user’s bits data.

REW : During rewind

(UB) indication

(Example) Time code TC 00 : 00 : 00 : 00

STL

: During still picture playback mode

FWD : During playback in forward direction (FWD1: About ×2 speed, FWD2: About ×5 speed, FWD3:

About ×10 speed)

Colon (:) when non-drop frame mode

Dot (.) when drop frame mode

REV

: During playback in reverse direction (REV1: About ×2 speed, REV2: About ×5 speed, REV3:

About ×10 speed)

User’s bits UB FF EE DD 20

Whether or not to display this item is set with the TC/UB item on the LCD/VF[3/4] menu screen.

X See page 88.

Whether the time code or user’s bits should be shown is selected with the TC DISPLAY switch inside the

LCD door.

STOP : Stop mode (Tape protect mode)

EJECT : Cassette being ejected

- - -

: No tape loaded

Indication of date and time

LCD BRIGHT indication

Indicates the date and time.

Whether or not the date and time should be displayed as well as the display style are set on the TIME/

DATE menu.

Remaining tape indication

Remaining tape indication (displayed in 1-minute steps)

This indicator blinks when remaining tape time is equivalent to less than 3 minutes.

Whether or not to display this item is set with the TAPE REMAIN item on the LCD/VF[3/4] menu screen.

X See page 88.

* When inserting a brand-new tape, the remaining tape time is not indicated.

When the tape has been run, the indication will appear.

* The remaining tape indication is to be regarded only as a guide.

* When this device is used at low temperatures, it may take a while before the indication of the remaining

tape time appears.

When the brightness of the monitor screen is adjusted with the LCD BRIGHT button, the date and time

indications and the VTR mode indication 2 are turned off and the LCD BRIGHT indicator is displayed.

(Example)

BRIGHT +5 •••••+•••••O

Numeric value: Any of –5, –4, –3, –2, –1, 0, +1, +2, +3, +4, +5.

Indication of Black operation

B : Displayed when the black stretch or black compress settings are other than NORMAL.

Indication of skin tone detail SD : Indicated when skin tone detail is ON.

color operation

Voltage indication

(Example) 12.2V: Indicates remaining battery level in 0.1V steps.

Battery voltage and remaining battery are displayed. Select the display method in BATTERY INFO. on the

LCD/VF[3/4] menu screen. X See page 88.

Anton Bauer battery: Voltage/remaining capacity (%)/remaining time

IDX Endura battery : Voltage/remaining capacity (%)

Indication of Iris level opera- I : Displayed when the AE LEVEL setting is other than NORMAL

tion

Indication of FAW operation

Gain operation indication

FAW : Indicated when Full Auto White Balance is ON.

* dB : Indicates gain value when gain is other modes than 0 dB and ALC.

Indication of various function FOCUS

: Displayed when the Focus Assist function is ON.

operations SKIN AREA : Blinks while the skin detail color area is displayed.

ALC

FAS

: Displayed when ALC function alone is ON.

: Displayed when the Full Auto Shooting function is ON.

: Displayed when the shutter speed is a setting other than the default setting.

X See page 83.

Indication of DR-HD100 Oper- When a DR-HD100 (HDD unit by FOCUS enhancements) is connected, its operation status is displayed.

ation

[: DR-HD100 is connected (displays white)

[: Recording with DR-HD100 (displays red)

(For details, refer to the DR-HD100 INSTRUCTION MANUAL.)

CONTROLS, INDICATORS AND CONNECTORS

Indications on the LCD Monitor

and in the Viewfinder (Cont’d)

No.

Item

Contents

Audio sampling frequency in- 32 K : Indicated when the AUDIO MODE item on the AUDIO/MIC[1/2] menu screen is set to 32 K. (Audio

dication

is recorded with 12-bit, 32 kHz sampling.)

48 K : Indicated when the AUDIO MODE item on the AUDIO/MIC[1/2] menu screen is set to 48 K. (Audio

is recorded with 16-bit, 48 kHz sampling.) When HDV format is set, 48K is displayed.

X See page 84.

STATUS 2 Screen

STATUS 3 Screen

STATUS 2

Whether or not to display this item is set with the AUDIO item on the LCD/VF[3/4] menu.

This screen displays the camera setup statuses.

Event display is not available while this screen is displayed.

Audio level meter indication

Displays the CH-1, CH-2 audio level meters.

Whether or not to display this item is set with the AUDIO item on the LCD/VF[3/4] menu.

X See page 88.

Indication

Indication Contents

FILE

F CAM1 [********], CAM2-4 [********], and EXT1 - 4 [********] * indicates SUB NAME X See pages 96-98.

Standard audio level indication The level at which audio is recorded on the tape is indicated by “O”.

A F symbol is displayed when a menu setting read from LOAD FILE was changed.

–20 dB, –12 dB

The display disappears when the setting is saved using STORE FILE.

X See “AUDIO REF.LEVEL” on page 84.

FULL AUTO

GAIN

ON, OFF

0dB, 3dB, 6dB, 9dB, 12dB, 15dB, 18dB, ALC

–20 dB

–12 dB

SHUTTER

(When STEP is selected)

OFF, 1/6, 1/6.25, 1/7.5, 1/12, 1/12.5, 1/15, 1/24, 1/25, 1/30, 1/48, 1/50, 1/60, 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000,

CH-1

CH-2

\ \ \ ]

1/4000, 1/10000

(When VARIABLE is selected)

1/24.01 - 1/10489.5

Iris indicator display

Iris F-value indication

Filter position indication

M: Iris set higher than normal

b: Iris set to normal

N: Iris set lower than normal

(Displayed when FAS or ALC mode is selected)

EEI

* The range for the shutter speed differs depending on the video format. X See page 83.

The indication can be switched ON/OFF with the F.NO/IRIS IND. item on the LCD/VF[1/4] menu screen.

X See page 86.

WHT. BAL

A[##00K], B[##00K], PRESET[##00K], FAW, MANUAL (Only when the remote control unit is used)

For A and B, ## represents 23, 25, 28, 30, 32, 34, 37, 43, 52, 65, or 80. For PRESET, 32 or 56.

AE LEVEL

FILTER

ZEBRA

–3, –2, –1, NORMAL, +1, +2, +3

Indicates the F-number of the connected lens.

OPEN, F2, F2.8, F4, F5.6, F8, F11, F16, CLOSE

It is not displayed when the lens is removed. For some lenses, no display appears.

The indication can be switched ON/OFF with the F.NO/IRIS IND. item on the LCD/VF[1/4] menu screen.

X See page 86.

OFF, ND1 [1/4ND], ND2 [1/16ND]

60-70%, 70-80%, 85-95%, OVER 95%, OVER 100%

Displays the remaining tape (minutes)

REMAIN

AUDIO

Displays the audio sampling frequency and the audio level adjustment mode (Ex: 32K (CH1 Z CH2 a) Z (for AUTO

mode) a (for MANUAL mode)

Indicates the current filter position.

No display : FILTER OFF

* When SHUTTER DISP. on the LCD/VF[3/4] menu screen is set to DEG, the shutter display for the frame rate in 24p or 25p mode is degrees.

Indication Indication Contents

SHUTTER

ND1

ND2

: FILTER ND1 (1/4ND)

: FILTER ND2 (1/16ND)

The indication can be switched ON/OFF with the FILTER item on the LCD/VF[1/4] menu screen.

X See page 86.

(When STEP is selected)

360.0°, 180.0°, 172.8°, 150.0°, 144.0°, 135.0°, 120.0°, 105.0°, 90.0°, 75.0°, 60.0°, 45.0°, 30.0°, 22.5°, 11.2°

(When VARIABLE is selected)

Audio Lock Indication

Displayed when the audio signal is locked to the video signal.

24p: 0.82° to 359.4°, 25p: 0.85° to 359.4°

STATUS 3

Displays a list of setting statuses for USER1, 2, and 3 as well as LENS RET item on the SWITCH MODE menu screen.

X See page 83.

Events are not displayed while these statuses are being displayed.

Indication

Indication Contents

USER1

USER2

NONE, BARS, PRESET TEMP., B.STRETCH1 to 5, B.COMPRESS1 to 5, AE LEVEL+, AE LEVEL–, RET, LOAD FILE

USER3

NONE, BARS, PRESET TEMP., B.STRETCH1 to 5, B.COMPRESS1 to 5, RET, LOAD FILE

RET, FOCUS ASSIST

LENS RET

STATUS 4

This screen only displays VTR mode indication, date and time, event display and alarm indications.

Whether or not date and time should be displayed and the display style are set on the TIME/DATE menu screen.

X See “Displaying the Time and Date on the Screen” on page 42.

CONTROLS, INDICATORS AND CONNECTORS

No.

Item

Contents

Indications on the LCD Monitor

and in the Viewfinder (Cont’d)

Time/Date indication

Recorded data are displayed during playback, fast forward, and rewind.

During recording in DV format, the data from the IEEE1394 connector is displayed.

During recording in HDV format, the data of internal clock is displayed.

(HDV/DV signal input is possible with the GY-HD200U, GY-HD201E.)

Whether or not the date and time should be displayed and the display style are set on the TIME/DATE

menu screen. X See page 92.

When the date and time have not been set, the following indication appears.

- -/- -/- - - -: - -: - -

Status Screen in VTR MODE

Voltage indication

(Example) 12.2V : Indicates remaining battery level in 0.1V steps.

Battery voltage and remaining battery are displayed. Select the display method in BATTERY INFO. on the

LCD/VF[1/2] menu screen X See page 88.

Anton Bauer battery: Voltage/remaining capacity (%)/remaining time

IDX Endura battery : Voltage/remaining capacity (%)

Audio Lock indication

Displayed when the audio signal from DV recording or playback is locked to the video signal.

Magnified Status Indications on the

LCD Monitor

The characters on the status screens can be showed alone

in magnified size on the LCD monitor.

DISPLAY button

No.

Item

VIDEO FORMAT display

Contents

Displays the video format recorded on the tape when in VTR mode. Also displays the video format of the

HDV/DV input signal.

You can switch this display ON/OFF using the VIDEO FORMAT item on the LCD/VF[1/2] menu screen.

X See page 88.

Time code (TC) and user’s bits Displays the time code data being recorded (hour, minute, second, frame) when in VTR mode.

(UB) display

You can switch this display ON/OFF using the TC/UB item on the LCD/VF[1/2] menu screen.

X See page 88.

266S DD

You can select to display either the time code or the user’s bits using the TC DISPLAY switch in the LCD

door.

Remaining tape time

Remaining tape indication (displayed in 1-minute steps)

This indicator blinks when remaining tape time is equivalent to less than 3 minutes.

Whether or not to display this item is set with the TAPE REMAIN item on the LCD/VF[1/2] menu screen.

X See page 88.

* When inserting a brand-new tape, the remaining tape time is not indicated.

When the tape has been run, the indication will appear.

* The remaining tape indication is to be used only as a guide.

* When this device is used at low temperatures, it may take a while before the indication of the remaining

tape time appears.

1. Set the LCD+VF item on the LCD/VF[4/4] menu screen to ON. X See page 89.

2. When the DISPLAY button is briefly pressed while the LCD monitor is displayed, the displayed contents change every time the

DISPLAY button is pressed.

Only image displayed

Characters shown enlarged

Image and characters displayed

Event display

Displays messages related to VTR operations. X See pages 102-104.

Audio sampling frequency in- The audio sampling frequency used for the recording is displayed during playback.

dication

No.

Item

Contents

Displayed during recording and playback when the audio signal is locked to the video signal.

(32 K, 48 K, 44.1 K)

Audio Lock Indicator

Whether or not to display this item is set with the AUDIO item on the LCD/VF[1/2] menu screen.

Time Code Generator Setting Indicates the set status of the TC GENE switch on the side section.

X See page 88.

Indicator

FREE : TC GENE switch is set to PRESET-FREE RUN MODE.

RECR : TC GENE switch is set to PRESET-REC RUN MODE.

REGN : TC GENE switch is set to REGEN MODE.

Audio level meter indication

VTR mode indication

Displays the audio level meters during playback.

Whether or not to display this item is set with the AUDIO item on the LCD/VF[1/2] menu screen.

X See page 88.

DUPL : There is 1394 input in VTR mode and TC DUPLI. menu is set to ON.

Indicates the VTR operation status

Drop/Non-drop Indicator

Indicates the framing mode of the time code.

STBY, STOP, PLAY, REC, FF, REW, FWD, REV, STL, - - - (No tape loaded), SLOW: During variable play-

back in forward direction (Displayed when using non-linear editing software.)

(SLOW+1: About ×0.1 speed, SLOW+2: About ×0.2 speed, SLOW+3: About ×0.5 speed)

During variable playback in reverse direction (Displayed when using non-linear editing software.)

(SLOW–1: About ×–0.1 speed, SLOW–2: About ×–0.2 speed, SLOW–3: About ×–0.5 speed)

NDF : Non-drop frame mode

Indication of DR-HD100 Oper- When a DR-HD100 (HDD unit by FOCUS enhancements) is connected, its operation status is displayed.

ation (For details, refer to the DR-HD100 INSTRUCTION MANUAL.)

: Drop frame mode

MEMO

When characters indicating the status are displayed in

magnified size on the LCD monitor, the viewfinder display

the image.

CONTROLS, INDICATORS AND CONNECTORS

SAFETY ZONE

CENTER MARK

2.35:1CE

OFF

2.35:1CH

OFF

Indications on the LCD Monitor

and in the Viewfinder (Cont’d)

Alarm Message Display

•

The following alarm messages are displayed while the STA-

TUS (0, 1, 4) screen is shown in the Camera mode, or a STA-

TUS screen is shown in the VTR mode.

DV-60I

DV-50I

4:3

Cannot be selected

DV-24P

DV-24PA

DV-25P

If an alarm is generated while the STATUS 2, 3 screen is

shown, the STATUS 0 screen returns to display the alarm.

X See page 102.

When an abnormality occurs in the VTR, a warning message

with an error code is displayed.

16:9

HDV-HD60P

HDV-HD50P

HDV-HD30P

HDV-HD25P

HDV-HD24P

•

Auto White Balance Indication

(Camera mode only)

[16:9]

X See pages 102-104.

The AUTO WHITE indication and the result of the operation are dis-

played during the auto white balance adjustment operation.

X See “White Balance Adjustment” on page 51.

Switching between the LCD Screen

and Viewfinder Display

„ When the LCD+VF item in the LCD/VF[4/4] menu is set to

OFF, the LCD monitor and viewfinder (VF) displays are as

shown below.

DISPLAY button

Alarm display area

LCD Monitor Status

LCD Display

VF Display

LCD Closed

Normal LCD

Inverted LCD

Normal LCD

Inverted LCD

OFF

LCD Open

OFF

Normal LCD

OFF

Menu Setting Screen

MEMO

Screen used for making various settings.

The Menu Setting Screen appears when the STATUS button is

pressed for 1 second or more.

X See “Setting Menu Screens” on page 72.

•

You can switch between the LCD monitor and the view-

finder by holding down the DISPLAY button for about 2

seconds.

Inverted LCD

•

After you set up the function that switches the display

between the LCD monitor and the viewfinder by holding

down the DISPLAY button, the display mode is cancelled

by the LCD monitor open/close and normal/inverted

operations.

LCD open 40° or

LCD close less

than 40°

•

If the LCD monitor is closed inside this device with the

screen in the normal display orientation, holding down

the DISPLAY button does not work.

„ When the LCD+VF item in the LCD/VF[4/4] menu is set to

ON, the LCD monitor and viewfinder (VF) displays are as

shown below.

TOP MENU screen (Camera mode)

LCD Monitor Status

LCD Display

VF Display

Safety Zone Indication (Camera mode only)

LCD Closed

Normal LCD

Inverted LCD

Normal LCD

Inverted LCD

OFF

The indication of the following safety zone and center mark indications can be turned ON/OFF with the SAFETY ZONE item and CEN-

TER MARK item on the LCD/VF[1/4] menu screen. X See page 86.

In addition, the safety zone display is on or off depending on the REC item setting and the ASPECT item setting in the VIDEO FOR-

MAT[1/2] menu screen, as shown below.

LCD Open

SAFETY ZONE

CENTER MARK

OFF

4:3

14:9

16:9

16:9+4:3

OFF ON

OFF

MEMO

REC

ASPECT

•

Press the DISPLAY button for 2 seconds to switch the

LCD screen display ON and OFF.

The viewfinder screen is always displayed.

DV-60I

DV-50I

DV-24P

DV-24PA

DV-25P

4:3

Cannot be selected

•

16:9

HDV-HD60P

HDV-HD50P

HDV-HD30P

HDV-HD25P

HDV-HD24P

[16:9]

PREPARATIONS

1. 3. Knob

2. Microphone

Basic System

Attaching the Zoom Lens

1. Loosen the mount ring.

Shoulder Belt

Microphone

holder

2. Attach the lens with its pin aligned with the hole in the

mount.

Component Cable

BNC

3. Tighten the mount ring.

4. Connect the cable connector.

5. Clamp the lens cable.

Microphone

XLR 3P

Monitor

Composite Cable

RCA pin

Earphone

Audio Cable

RCA pin

5. Clamp

Hole

Focus Manual Unit

*1 HZ-FM13 (FUJINON)

HZ-FM15 (CANON)

Monitor

HDD Unit

DR-HD100

Microphone

IEEE1394 Cable

6P-6P

4. INPUT1, 2 connector

1/3 Zoom Lens

Th13 × 3.5BRMU (FUJINON)

For GY-HD200U

Clamp

DV VTR

How to Attach the View-

finder

USER

Wide Converter

WCV-82SC

STATUS

Anton Bauer

Battery Charger

WHT.BAL

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

Anton Bauer

Battery

OFF

POWER

REC

1/3 Zoom Lens

CAUTION

Focus Manual Unit

Th16 × 5.5BRMU (FUJINON)

BR-HD50

(Excluding the CHU/CHE model)

Battery mount

For GY-HD200E/GY-HD201E

•

Be sure to tighten the mount ring completely. Incomplete

tightening may result in the lens dropping off or disturbed

back focus.

Set this device’s power switch to “OFF” before the zoom

lens is attached or detached.

GY-HD200U: Gold Mount

GY-HD200E: V Mount

GY-HD201E: V Mount

1.To attach the viewfinder, slide it in the direction of the

Non-linear Editing System

SD Memory Card

2.^aS^re^rot t^wh^.e viewfinder to a comfortable position and then turn

Zoom Servo Unit

HZ-ZS13B

•

IDX

Battery Charger

the slide mounting ring and mount.

GY-HD200U/GY-HD200E/GY-HD201E

Standard Package

IDX (Endura)

Battery

„ To take off the viewfinder, pull the knob in the direction of

the arrow as you slide the viewfinder.

Mount Converter

(1/2r1/3): ACM-12

(2/3r1/3): ACM-17

XLR 4P

Knob

Tripod Base

Taking off the viewfinder

Attaching the Microphone

(Provided)

AC Adapter

1/2 Zoom Lens

S14 × 7.3B12U (FUJINON)

S17 × 6.6BRM (FUJINON)

S20 × 6.4B12U (FUJINON)

YH16 × 7K12U (CANON)

YH19 × 6.7K12U (CANON)

2/3 Zoom Lens

2. ^{Slide mounting ring}

Remote Control Unit

RM-LP55/RM-LP57

Carrying Case

Tripod

Connect the provided microphone to the microphone holder.

Provided microphone is a phantom microphone.

1. Turn the knob on the microphone holder anticlockwise to

loosen it and open the microphone holder.

Dolly

2. Place the microphone in the microphone holder.

Place the microphone toward the front to prevent it from

interfering with the cassette cover.

An HZ-FM13 cannot be used with a Th16 × 5.5BRMU or S14 × 7.3B12/U zoom lens.

Use a FUJINON focus manual unit (FMM-8, CFH-3, CFC-12-990).

For details, please consult your JVC authorized dealer.

3. Turn the knob on the microphone holder clockwise to

secure the microphone.

4. Connect the microphone cable to the INPUT1 or INPUT2

input connector on this device.

5. Attach the microphone cable to the clamp.

6. Make sure to perform the correct setting for use of a

phantom microphone.

X See page 55.

PREPARATIONS

3.Close the SD memory card cover.

CAUTION

How to Attach the Viewfinder

(Cont’d)

•

The front base mount may be locked while the pin of the

tripod base is not inserted into the hole on the rear base

mount of this device. Therefore, after mounting, make

sure that these parts are engaged properly.

Attaching the Tripod Base

(Optional)

Cutout

•

When moving this device mounted on

tripod, any

impact or vibration should be avoided as this may cause

this device to become detached and to drop from the tri-

pod.

Be sure to remove this device from the tripod before

transporting it.

Use the optional tripod base to place the camera on a tripod.

About the Viewfinder Cable

Attach the viewfinder cable to the clamp 7 on page 14.

To reduce the emission of unwanted radio waves, be sure to

attach the provided core filter as shown in the figure below.

1. Attach the tripod base on the tripod by using the hole that

balances this device most optimally.

•

Attach the core filter (black) as close to this device as pos-

sible, as shown in the figure.

SD memory card cover

1. Tripod mounting holes

Taking out the SD memory card

2. While pushing the safety lever, pull the lock lever toward

1.Push the SD memory card in the direction of the arrow.

the front until the front mount clip clicks into place.

•

The SD memory card comes out slightly.

3. Pin

2.Pull the SD memory card straight out.

Front mount clip

Core filter (black)

2. Safety lever

Lock lever

Inserting an SD Memory

Card

3. Place this device on the tripod base by aligning the rear

base mount of this device with the pin on the tripod base.

By using an SD memory card, you can save and call up menu

settings and camera settings for this device.

X See “FILE MANAGE Menu Screen” on page 96.

Check that the POWER switch is OFF.

About SD Memory Cards

•

When you use an SD memory card that is either new or

was formatted on a device other than this device, format it

on this device.

Inserting an SD Memory Card

4. Front base mount

3. Rear base mount

X See page 98.

Recommended SD memory cards

Panasonic: 16 MB to 2 GB

1. Open the SD memory card cover.

4. Hold the camera on the top and slide forward so that the

base mount of the camera is locked by the front mount

clip of this device as it clicks into place.

2. Face the cutout end of the SD memory card inward and

insert it in the direction of the arrow.

•

You can write-protect the card so that saved files are not

mistakenly erased. Set the switch on the side of the SD

memory card to the “LOCK” position.

CAUTION

Be sure not to touch the metal connector area of the SD

memory card.

LOCK switch

VF BRIGHT

USER

ND FILTER

STATUS

WHT.BAL

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

OFF

POWER

REC

MEMO

SDHC-compliant memory cards cannot be used with this

device.

PREPARATIONS

„GY-HD200E/GY-HD201E

Charging the Built-in Battery

Use an IDX (Endura) battery.

AC Operation

Battery Operation

Attaching the Battery

The built-in, rechargeable backup battery retains the date

and time and the time code data.

1.Face the battery terminals down and align the battery V-

The built-in battery is constantly being charge whenever this

device is connected to a power supply, but it gradually dis-

charges while this device is disconnected from a power sup-

ply. The battery will be fully discharged when this device is

not used for about three months, in which case the set date

and time and time code data are reset.

In this case, recharge the built-in battery and then set the

date and time and time code data again.

However, it is possible to use this device even if the built-in

battery is discharged but the date and time and time code

data cannot be recorded.

mount with the battery adapter V-mount attachment.

This device is operable with AC power supply or battery

pack.

Use the AC adapter as the AC power supply.

The attachable battery varies depending on location.

Recommended batteries

U model: Dionic 90 (Anton Bauer)

E model: Endura-7 (IDX)

V-mount

attachment

1. After making sure that the power switches of this device

and of the AC adapter are set to OFF, connect the DC

cable to the DC OUTPUT connector of the AC adapter

and the DC INPUT connector of this device as shown in

the illustration.

CAUTION

Use only the recommended batteries.

If a heavy battery is used, the battery may fall out depend-

ing on the way the HD camera recorder is used.

•

To lessen the amount of unnecessary radio waves

emitted, attach a provided Clamp filter near both ends

of the DC cable as shown in the diagram.

„GY-HD200U

Use an Anton Bauer battery.

How to charge the built-in battery

1.Connect the AC adapter to this device and an AC outlet

or mount a charged battery on this device.

2.Set the POWER switch on this device to “ON” or “OFF”

(charging takes places with the POWER switch set to

either of the positions).

Attaching the Battery

2.Slide the battery down until it clicks and locks.

•

The battery is attached.

1. Align the battery guide pins (three places) with the bat-

tery adapter guide holes and insert straight. Battery will

not be properly attached if guide pins are not straight.

3.Leave the equipment in this condition for about 4 hours.

•

The built-in battery will remain charged for about

months after being charged for about 4 hours.

Removing the Battery

Slide the battery up while holding down the lock release but-

ton to remove the battery.

Clamp filter

Guide pins

Cassette cover

side panel

Guide

holes (×3)

DC INPUT

Release button

Battery

Release lever

DC cable

Battery pack

(trim pack)

LCD screen

side panel

2. Slide the battery towards the Cassette cover side panel

DC OUTPUT

until it clicks.

•

The battery is attached.

Clamp filter

AC adapter

Removing the Battery

Slide the battery towards you (LCD screen side panel) while

holding down the release lever, and pull away from the

device to remove the battery.

2. Press the POWER switch of this device to ON. Power is

supplied to the VTR section and the camera.

CAUTION

•

Do not remove or connect the DC cable while recording

is being performed.

Release lever

Battery

•

Do not use any power source with large fluctuations in

the power source voltage, power sources generating

noise, such as ripples or power sources with lower volt-

age.

PREPARATIONS

PREPARATIONS FOR OPERATION

•

When you use an Anton Bauer battery, the remaining

battery (capacity or time) can be displayed in the STA-

TUS 1 screen of the LCD screen or viewfinder. Set BAT-

TERY INFO. on the LCD/VF[3/4] menu screen to

CAPA% or TIME to display the remaining battery. When

using the IDX Endura battery, the remaining capacity (%)

can be displayed. X See page 88.

Battery Operation

(Cont’d)

Turning the Power OFF

Turning the Power ON

1.Place this device in the record-standby or STOP mode.

2.Set the POWER switch to OFF.

3.Remove the battery pack or the power supply to the DC

INPUT connector. (When the camera is not going to be

used for a longer period.)

Turning the Power ON

Precautions for the Battery Opera-

tion

CAUTION

1. Set the POWER switch to ON.

Operating Time with Battery Pack

This device turns on in Camera mode.

•

Do not set the POWER switch to OFF while recording is

taking place.

Confirm that the “STBY” or “STOP” indication is shown in

the VTR operation mode indication area before the

power is turned off.

Should the POWER switch accidentally be set to OFF

during a recording, wait at least 5 seconds before turning

the power on again.

Always set the POWER switch to OFF before discon-

necting the power supply.

•

Do not detach the battery pack while recording is taking

place.

Do not connect or disconnect the DC cable while operat-

ing with a battery pack.

The following symptoms may occur if the DC cable is con-

nected or disconnected while operating with

pack.

When a fully charged battery pack is attached, the approxi-

mate continuous operating time is as follows

„ The operation differs according to whether this device is in

the Camera mode or in the VTR mode.

The mode switches each time you press the CAM/VTR button.

When the mode is switched, the VTR indicator displays

the following statuses.

Battery Pack

Continuous Operating Time (at 25°C (77°F))

Approx. 3.2 hours

Dionic 90

(U model)

battery

Endura-7

(E model)

Approx. 2.5 hours

While the mode is being switched : Flashing

•

The power is cut off for a moment when the DC cable is

In VTR mode

: Lit

disconnected.

In Camera mode

: Off

•

Battery operating time may differ depending on the age of

the battery pack, charging conditions and the operating

environment, etc. Use the values in the table on the above

for approximate reference times.

•

Noise to the video and audio signals occurs. Audio sig-

nal are muted.

Do not remove the battery pack or turn AC adapter OFF

while the POWER switch on the camera is still set to ON.

•

When operation is continued with DC input after the bat-

tery pack capacity has been used up, set the POWER

switch to OFF after the DC power is applied. Then switch

ON again.

If this device is left with the battery pack attached, a small

amount of power is consumed even if the POWER switch

on this device is set to OFF.

•

Operating time is reduced in areas with a cold environ-

ment.

Operating time is reduced when the power zoom lens and

LCD are used frequently.

VTR indicator

Remove the battery pack when this device is not going to

be used.

Precautions for the Battery Pack

VF BRIGHT

•

When the battery pack is not in use, it must be stored in a

cool, dry place.

USER

Remaining Battery Power Display

ND FILTER

LCD BRIGHT

Do not leave the battery pack in a place where it might be

subject to a high temperature (under direct sunlight in a

car, etc.), this could cause leakage of the fluid or shorten

service life.

CAM/VTR

AUDIO SELECT

CH-1

CH-2

DISPLAY

GENE.

FREE

AUTO

MANU

REC

STATUS

REGEN

LCD monitor/Viewfinder

WHT.BAL

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

•

When the terminal section of the battery pack gets dirty,

the operating time will be shortened.

If the operating time becomes greatly reduced even imme-

diately after recharging, the service life of the battery pack

is nearly finished.

OFF

POWER

REC

CAM/VTR button

POWER switch

Camera mode

Purchase a new battery pack.

This device enters the Camera mode. The camera image

is displayed in the viewfinder or on the LCD monitor. When

a recordable videocassette is loaded, this device enters

the record-standby mode automatically. “STBY” is dis-

played in the VTR operation mode indication area of the

LCD monitor and/or in the viewfinder. In this condition,

press the REC/VTR trigger button to start recording.

Playback is also possible in the Camera mode.

Playback operation becomes possible when the STOP

button is pressed to set the VTR operation mode indica-

tor to indicate “STOP”.

Recharging

When the remaining battery power is nearly exhausted, the

following warnings will be generated.

„ Viewfinder screen or LCD monitor

When a Status screen is displayed (excluding the STATUS

2, 3 screen in the Camera mode)

•

Recharge the battery pack after completely discharging it.

Repeated recharging with residual charge remaining could

result in reduced battery capacity.

If the battery capacity is reduced by repeating incomplete

recharging, or recharging without discharging, once dis-

charge the battery pack completely, then recharge it to

restore the battery capacity.

If the battery pack is recharged with its internal tempera-

ture raised immediately after use, recharging may not be

performed completely.

Perform charging in an environment where the tempera-

ture is between 10°C (50°F) and 35°C (95°F). 20°C (68°F)

to 25°C (77°F) is the ideal temperature range for charging.

If the environment is too cold, charging may not complete.

•

Alarm indication: LOW VOLTAGE displayed.

„ FRONT and BACK TALLY lamp on camera: Blinks

„ Monitoring loudspeaker and PHONES jack: Alarm sound

VTR mode

This device enters the VTR mode. The camera image will

not be displayed in the viewfinder or on the LCD monitor.

When a videocassette is loaded, this device enters the

stop mode.

“STOP” is displayed in the VTR operation mode indication

area of the LCD monitor and/or in the viewfinder.

HDV/DV input is possible through the IEEE1394 connector.

•

MEMO

•

After the remaining battery power warnings appear, this

device automatically stops operation if the battery power

operation is continued.

PREPARATIONS FOR OPERATION

TC/UB/CLOCK menu screen

Unloading the Cassette

Loading/Unloading the

Cassette

Setting and Displaying the

Date and Time

1.Turn the POWER switch to ON.

2.When this device is in shooting standby mode or stop

mode, slide the EJECT switch to the side and wait until

the videocassette cover opens completely.

The date and time of the built-in clock should be set. Pow-

ered by the built-in backup battery the set date and time data

continue to count even when the power is switched off.

The set date and time data are displayed on the LCD mon-

itor or in the viewfinder and recorded on the tape in accor-

dance with the settings made on the menu screen.

Cassette Loading

•

The LED next to the EJECT switch flashes.

A few seconds pass before the videocassette tape is

ejected.

•

Use a videocassette tape marked MiniDV.

•

To record, slide the switch on the back for use in prevent-

ing accidental erasure to the “REC” side.

3.The LED turns off and the videocassette cover opens.

Take out the videocassette tape.

•

Remove any the tape slack before loading.

5.Make settings on the TIME/DATE menu screen. (This

4.Carefully push the center of the videocassette cover in

includes display style, etc.)

1. Turn the POWER switch ON.

the direction of the arrow as far as it will go to close it.

Setting the Date and Time Style

2. Slide the EJECT switch on the top panel of this device to

TIME/DATE menu screen

CAUTION

the side.

The date and time are set on the menu screen.

When setting while observing on a monitor connected to the

connector, set the ANALOG OUT CHAR. item on the OTH-

ERS[1/2] menu screen to ON.

•

When you close the videocassette cover, push it in firmly

as far as it will go. If the videocassette cover is not closed

properly, it becomes half-locked and this device cannot

function.

The videocassette cover opens automatically and a vid-

eocassette tape can be inserted.

3. Insert a videocassette tape into the videocassette holder.

With the tape window facing out, move the switch on the

back of the videocassette up and firmly push the center

back of the videocassette straight in as far as it will go.

If this happens, firmly push the videocassette cover in

again as far as it will go to lock it.

1. Set the POWER switch to ON.

2. Press the STATUS button for 1 second or longer to dis-

•

The videocassette cover does not open during recording

even if you slide the EJECT switch.

Do not leave the videocassette cover open for a long

time.

play the TOP MENU screen.

4. Carefully push the center (“Push here” sticker) of the vid-

eocassette cover in the direction of the arrow as far as it

will go to close it.

•

After the cover is closed, it takes about 10 seconds

until recording can begin or this device can enter

STOP mode.

Dust or dirt may enter the inside and cause damage.

Do not touch the videocassette cover or interfere with the

eject operation while ejecting is in progress. This will

cause damage.

When you close the videocassette cover, do not press

the black area of the inner cover.

USER

DATE STYLE : Selects the style for displaying the

date.

•

SHUTTER dial

ND FILTER

YY/MM/DD (Year, month, day)

MM/DD/YY (Month, day, year)

DD/MM/YY (Day, month, year)

REC/SAVE

Tape window

switch

TIME STYLE : The time can be set to display as a 12-

hour or 24-hour clock system.

SEC DISPLAY : To select whether or not indication of

seconds should be displayed on the

screen.

STATUS

EJECT switch

STATUS button

Cassette holder

WHT.BAL

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

OFF

TIME SHIFT

: Adds time to the built-in clock (time

compensation) and displays it. The

adjusted time is also recorded on the

tape.

POWER

REC

1Rotate the SHUTTER dial to align the cursor (K) with

the item to be set, and then press the SHUTTER dial.

1. ^{POWER switch}

•

The setting area of the selected item starts blinking.

3. Rotate the SHUTTER dial to align the cursor (K) with the

TC/UB/CLOCK item, and then press the SHUTTER dial

in the direction of the camera body.

Videocassette cover

Inner cover

2Rotate the SHUTTER dial to change the setting, and

then press the SHUTTER dial.

•

The setting area stops blinking and the setting is

entered.

•

The TC/UB/CLOCK menu screen appears.

4. Rotate the SHUTTER dial to align the cursor (K) with the

„ If the power is on, the modes are as shown below.

MEMO

TIME/DATE item, and then press the SHUTTER dial.

REC/SAVE switch

MODE

•

The TIME/DATE menu screen appears.

Set the DISPLAY item on the TIME/DATE menu

screen to ON.

The TIME STYLE, SEC DISPLAY, DATE STYLE and TIME

SHIFT items can also be set and changed after the date

and time have been set.

REC

SAVE

STOP mode

Camera

VTR

Record-standby mode

REC INHIBIT is displayed

on the LCD monitor and in

the viewfinder.

STOP mode

PREPARATIONS FOR OPERATION

Setting and Displaying the Date

and Time (Cont’d)

Displaying the Time and Date on the

Screen

Time code input entered the

IEEE1394 connector (GY-HD200U/

GY-HD201E only)

Displaying Time Code

Whether or not the time and date should be displayed on the

screen and how to display them are set on the TIME/DATE

menu screen.

This device records SMPTE-standard (NTSC) or EBU-stan-

dard (PAL) time codes and user’s bits. In the play mode or

the record mode, the reproduced time codes or user’s bits

are shown on the LCD monitor or in the viewfinder.

Pressing the STOP button for 1 second in the EJECT or stop

mode displays the DV input time code data or user’s bit data

from the IEEE1394 connector on the STATUS screen.

Setting the Date and Time

DTCG : The time code data from the IEEE1394 connector

DUBG : The user’s bit data from the IEEE1394 connector

1. Display the CLOCK ADJUST menu screen.

Select the CLOCK ADJUST item on the TIME/DATE

menu screen.

The time codes or user’s bits can be shown on the LCD mon-

itor or in the viewfinder during playback and recording as fol-

lows. (Status screen)

To return to display of the original time code or user’s bit,

press the STOP button. (Display of the normal time code or

user’s bit is also restored by performing VTR operation.)

TIME/DATE menu screen

Setting

MEMO

1. Set the TC/UB item on the LCD/VF[3/4] menu screen to

•

To record HDV/DV input time code and user’s bit from

the IEEE1394 connector, set the TC DUPLI. item on the

TC/UB/CLOCK menu screen to ON.

ON.

Date

Time

•

Time codes or user’s bit data are displayed on the

STATUS screen.

X See page 90.

1.Display the TIME/DATE menu screen.

•

To maintain the continuity of time code data, use with the

TC GENE. switch set to REGEN mode when recording

HDV/DV input signal from the IEEE1394 connector.

There is no time code display for HDV input.

Time code indication

Select the TC/UB/CLOCK item on the TOP MENU

screen.

(Example)

Time code indication

00:00:00:00

2Select the TIME/DATE item on the TC/UB/CLOCK

menu screen.

User’s bits indication

FF EE DD 20

2.Set the TIME/DATE menu screen.

2. Set the date and time.

CAUTION

The blinking digit is the one to be set.

•

DISPLAY item : Sets whether or not date and time

should be displayed.

A time code with a duration of more than 2 hours may not

be displayed correctly by DV components for general con-

sumer use, as some of these lack the capability to display

longer time codes.

CLOCK ADJUST menu screen

Date

Set to ON to display the indications.

•

DISPLAY MODE : Sets the video output mode in

item

which date and time should be dis-

played.

BARS

CAM

Displayed when outputting the color

bar.

STATUS 1 screen

: Displayed when outputting the color

camera image.

: Sets the style in which the date and

time are displayed.

: Date and time are displayed.

: Date only is displayed.

2. Whether time codes or user’s bit data should be dis-

played is selected with the TC DISPLAY switch inside the

LCD door.

BARS+CAM

DISPLAY

STYLE item

DATE+TIME

DATE

Date and time are always displayed.

•

: Time codes are displayed.

: User’s bit data is displayed.

Time (Hour:Min)

TIME

: Time only is displayed.

1When the SHUTTER dial is pressed, the blinking digit

moves to the next digit.

2When the SHUTTER dial is rotated, the value of the

blinking digit changes.

„ Display of date and time in the various operation modes.

In Camera mode

: The date and time of the internal

clock are displayed.

LCD BRIGHT

CAM/VTR

When the SHUTTER dial is rotated upward, the value

becomes higher. When rotated downward, the value

becomes smaller.

3Repeat the procedure described in 1 and 2 above to

set the day, month, year, hours, minutes.

The digits indicating seconds cannot be set.

4Press the SHUTTER dial in sync with a time signal to

enter the date and time precisely.

In VTR playback mode : The date and time recorded on the

tape are displayed.

AUDIO SELECT

CH-2

In VTR stop mode

: The last read date and time values

are displayed.

DISPLAY

GENE.

FREE

CH-1

AUTO

MANU

REC

REGEN

When an HDV/DV sig- : The date and time of the DV input

nal is input from the are displayed in DV format. The

IEEE1394 connector

date and time of the internal clock

are displayed in HDV format.

TC DISPLAY switch TC GENE. switch

(GY-HD200U/GY-HD201E only)

3. When all the settings are completed, rotate the SHUT-

TER dial to align the cursor with the PAGE BACK item,

and then press the SHUTTER dial.

The TIME/DATE menu screen returns.

4. ^•To return to the normal screen, use either of the following

methods.

Press the STATUS button

Return to the TOP MENU screen and then select the

EXIT item on the TOP MENU screen before pressing the

SHUTTER dial.

PREPARATIONS FOR OPERATION

„ TC/UB/CLOCK menu screen (FRAME RATE: 60/30)

Use the DROP FRAME item to select the framing mode

for the time code generator.

Presetting time code data

Presetting user’s bit data

Presetting and Recording

of Time Code

DROP

: The time code generator’s running method is

set the drop frame mode.

The time code and user’s bit data are preset on the TC/UB/

CLOCK menu screen.

The user’s bit data are preset with the UB PRESET item on

the TC/UB/CLOCK menu screen.

The method for setting is the same as the method for setting

the time code described on the left.

Use this setting when placing emphasis on

the recording time.

1. Display the TC/UB/CLOCK menu screen.

Select the TC/UB/CLOCK item on the TOP MENU

screen.

The time codes from the internal time code generator can be

recorded at the time of recording scenes.

The TC/UB/CLOCK menu screen differs depending on

whether the FRAME RATE item on the VIDEO FORMAT

menu screen is “60/30” or “50/25”.

There are two ways to preset the time code.

Set from the TC/UB/CLOCK menu screen.

Set in the LCD screen without opening the menu screen.

NON

DROP

: The time code generator’s running method is

set to the non drop frame mode.

Use this setting when placing emphasis on

the number of frames.

•

The user’s bit can be specified using numerals or alpha-

betic letters from 0 to F for each digit.

•

To record user’s bit data, set the UB REC item to ON (Only

when set to FRAME RATE 50/25).

TC/UB/CLOCK menu screen

(FRAME RATE: 60/30)

CAUTION

•

It is not possible to set all the digits of the user’s bit data to

This section explains how to set from the TC/UB/CLOCK

menu screen.

“F”.

Reading of the data during playback will not be possible for

an all-F setting.

See page 46 for instructions of setting from the LCD

screen.

Framing mode:

Drop frame/

Non-drop setting

Menu and switch settings to set the time code preset are the

same as the settings below.

Time code (hour, min, sec, frame)

Zero-resetting the Time Code or

User’s Bit Data

2. Set the time code (hours, minutes, seconds, frames).

Setting

1Rotate the SHUTTER dial to align the cursor (K) with

TC PRESET, and then press the SHUTTER dial.

This is performed with the TC or UB PRESET item on the

TC/UB/CLOCK menu screen. (Performed separately for the

time code and the user’s bit data.)

•

The first digit of the time code blinks.

The blinking digit is the one to be set.

To preset the Time Code, make the following settings.

„ TC GENE. switch

Set to REC or FREE.

MEMO

Drop frame/Non-drop frame mode

2When the SHUTTER dial is pressed, the blinking digit

changes.

In the NTSC system, the actual number of frames per 1

second is approximately 29.97 frames, but per time code

30 frames are processed. To compensate for this differ-

ence, the mode called “drop mode” drops frame 00 and 01

for every minute not divisible by 10.

1Rotate the SHUTTER dial to align the cursor (K) with the

TC or UB PRESET item, and then press the SHUTTER

dial.

REC

: The data preset in the time code generator

runs only during recording.

Use this setting if it is necessary to record

continual time codes across different scenes.

3When the SHUTTER dial is rotated, the value of the

blinking digit changes.

When the SHUTTER dial is rotated upward, the value

becomes higher. When rotated downward, the value

becomes smaller.

2Rotate the SHUTTER dial to select ZERO PRESET as the

setting value, and then press the SHUTTER dial.

However, approximately ±1-frame varia-

tions may occur in scene accuracy.

The “non-drop frame mode” is when no frames are dropped

and the actual time shift neglected.

MEMO

FREE

: The time code starts to run from the time it is

preset in the time code generator.

4Repeat the procedure described in 2 and 3 above to

set the desired value for all digits.

When a menu screen is not being displayed, you can zero

reset the time code data by simultaneously holding down

the USER2 button and the STOP button for about 1 sec-

ond.

„ TC/UB/CLOCK menu screen (FRAME RATE: 50/25)

Whether or not user’s bit data should be recorded can be

selected with the UB REC item on the TC/UB/CLOCK

menu screen.

5After setting the frame digit, press the SHUTTER dial to

make EXECUTE blink. The setting values are con-

firmed when the SHUTTER dial is pressed again.

To cancel the setting, select CANCEL and press the

SHUTTER dial.

TC/UB/CLOCK menu screen

(FRAME RATE: 50/25)

3. When all the digits are set

•

Press the STATUS button to return to the normal

screen

•

Rotate the SHUTTER dial to align the cursor (K) with

the PAGE BACK item, and then press the SHUTTER

dial to return to the TOP MENU screen.

PREPARATIONS FOR OPERATION

Presetting the Time Code

from the LCD Screen

Recording Time Codes in

Continuation of Time

Playing Back Time Code

Codes Recorded on Tape

The time code can be preset directly from the LCD screen

without opening the TC/UB/CLOCK menu screen.

This device features a time code reader. During playback,

the time code or user’s bit data recorded on the tape is dis-

played on the LCD screen or viewfinder status screen.

This device also incorporates a time code reader. Therefore,

when this device enters record mode from record-standby

mode, it can read the time code data recorded on the tape

and record time codes in continuation of the existing data.

The recorded user’s bit data are identical to the user’s bit

date recorded on tape.

However, approximately ±1-frame variations may occur in

scene accuracy.

To enable this function, set the time code related switches as

follows before starting recording.

CAUTION

MEMO

PRESET mode is not available in the following.

Blink

•

TC GENE. switch is set to REGEN.

TC DUPLI. item in the TC/UB/CLOCK menu screen is

set to ON.

•

During playback, if a portion of tape without recording

time code runs through, the time code stops running.

Playback continues.

When a tape with a time code that is longer than two

hours is played on home-use DV equipment, time code

may not be played properly on some models.

2.Press the USER2 button to reset all data.

•

Data becomes “00:00:00:00” and the hour digit starts

blinking.

•

Menu screen is displayed.

RECORDING mode is active.

Switching to CAM/VTR mode (When VTR indicator is

blinking).

3.Set the time code (hour, minute, second and frame).

The blinking digit can be set.

1Turn the SHUTTER dial to change the value of the

blinking digit. Turn the SHUTTER dial up to increase the

value and down to decrease the value.

Setting

„ TC/UB/CLOCK menu screen

•

Set the TC GENE. switch inside the LCD door to REGEN.

Set TC DUPLI. item on the TC/UB/CLOCK menu screen

to OFF.

2Press the SHUTTER dial to change the blinking digit.

•

Set framing of the time code generator in DROP

FRAME. (When set to FRAME RATE 60/30)

Set to enable/disable user’s bit recording in UB REC.

(When set to FRAME RATE 50/25)

3Repeat steps 1 and 2 and continue setting for each

row.

MEMO

•

The time code framing mode automatically becomes the

mode (drop frame or non drop frame) already recorded on

the tape.

4.Press the USER3 button to confirm the setting data.

„ Set the TC GENE switch to REC or FREE.

•

The LCD screen returns to the original screen.

MEMO

Presetting User’s Bit

You can specify the user’s bit with a number or character

between 0 - F.

See page 44 for details on the above settings.

About Time Code Mode

„ Camera mode

„ Set the TC DISPLAY switch.

Set to TC to preset time code and UB to preset user’s bit.

TC GENE. switch

REC

TC PRESET mode

CAUTION

FREE

REGEN

All digits of user’s bit cannot be set to F.

If all digits are set to F and read, user’s bit is deemed as

undefined during playback.

Operation

This section describes presetting of the time code.

TC REGENE mode

„ VTR mode/IEEE1394 input mode

TC/UB/CLOCK menu

TC GENE. switch

Aborting Preset Operation

While presetting, press the USER1 button while holding

down the STATUS button.

USER 2 button

USER 1 button

TC DUPLI. item

FREE

REC

REGEN

USER 3 button

OFF

TC PRESET mode

TC REGENE mode

IEEE1394 TC

SLAVE mode*

USER

IEEE1394 TC DUPLI. mode

•

Preset operation stops and the LCD screen returns to

the original screen.

SHUTTER

ND FILTER

IEEE1394 TC SLAVE mode is performed with special operations. X See page 48.

SHUTTER dial

VF BRIGHT

CAUTION

USER

OFF

ND FILTER

„ Preset operation is terminated in the following.

STATUS button

STATUS

WHT.BAL

•

TC DISPLAY switch is changed

CAM/VTR mode switch is changed

VTR operations are performed

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

STATUS

OFF

POWER

REC

„ USER1, USER2, and USER3 presetting in the SWITCH

MODE menus screen is not available when the Time Code

Preset screen is displayed.

„ The time code preset screen is displayed on the LCD

screen or viewfinder. It will not be output from the VIDEO

OUT terminal.

1. In Standby or Stop mode, press the USER1 button for

about 2 seconds while holding down the STATUS button.

•

The current time code generator data is displayed in

enlarged display mode on the LCD screen. The hour

digit starts blinking.

PREPARATIONS FOR OPERATION

Synchronizing with the

Screen Adjustment

Viewfinder Adjustment

Time Code of the IEEE1394

(DV)-Connected Master Unit

LCD monitor direction, angle, screen brightness, etc. can be

adjusted.

Direction of the Viewfinder

Adjust the position and angle of the viewfinder.

You can synchronize the time code when performing multi-camera recording. The internal time code generator will be synchro-

nized with the time code in the signal input from the IEEE1394 terminal. After synchronization (slave lock), the internal time code

generator continues to run even if the IEEE1394 cable is disconnected.

Diopter Adjustment

Rotate the eyepiece focusing ring until the viewfinder screen

image is clearly visible.

Adjusting the Direction and Angle of the

LCD monitor

Master unit

Slave unit

•

With the LCD door in the open condition, rotate the LCD

door.

Adjustment of the Viewfinder Screen

•

PEAKING:

•

It can be turned 180° in upward direction and 90° in down-

ward direction.

Adjusts the contour of the LCD monitor and the viewfinder

screen.

VF BRIGHT

When turned 180° upward direction, the LCD monitor can

be viewed from the lens side (vertically inverted image).

USER

ND FILTER

•

VF BRIGHT:

STATUS

Adjusts the brightness of the viewfinder screen.

WHT.BAL

AUTO

CH-1

AUTO

CH-2

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

AUDIO

LEVEL

OFF

POWER

REC

POWER

REC

PEAKING volume

Eyepiece focusing ring

Eyepiece

Slide the IEEE1394

switch to the [DV] side.

IEEE1394 terminal

Slide the IEEE1394

switch to the [DV] side.

LCDBRIGHT

button

IEEE1394 cable

VF BRIGHT volume

PEAKING volume

You can use the GY-HD200U or GY-HD201E as a slave unit.

You cannot use the GY-HD200E as a slave unit.

Status display

DTCG 00 : 00 : 00 : 00

Sliding securing ring

LCD

BRIG

Connections

Connect the master unit and the slave unit with an IEEE1394

M/V

AUDIO

CH-1

SELE

CH-2

AUTO

MAN

DISPL

TC SLAVE LOCK

GENE.

FREE

REC

REG

cable.

180° up

EXECUTE

CANCEL

USER1

USER3

90° down

Settings and Operations

•

Master unit (GY-HD200U/GY-HD200E/GY-HD201E/GY-

HD250U/GY-HD251E/GY-HD100, 101 series/GY-HD110,

111 series)

LCD lock release lever

Adjusting the LCD monitor

1. Set the IEEE1394 switch on the left side to [DV].

2. Set to Camera mode.

8.Check that the time code that is synchronized with the

•

PEAKING:

master unit is running.

Adjusts the contour of the LCD monitor.

LCD BRIGHT:

Adjusts the brightness of the LCD monitor.

3. Set the recording format to DV-60I or DV50I.

4. Set the TC GENE. switch to [FREE].

•

9.Disconnect the IEEE1394 cable.

10.The slave unit finally returns to Camera mode.

•

Slave unit (GY-HD200U/GY-HD201E)

Viewfinder mount base

Adjustments are made on the LCD/VF[2/4] menu screen.

X See page 87.

MEMO

1. Set the IEEE1394 switch on the left side to [DV].

2. Set to VTR mode.

Adjustments are made on the LCD/VF[4/4] menu screen.

„ Slave lock cannot be performed in the following

instances.

•

LCD MIRROR MODE:

X See page 89.

3. Check that the camera image from the master unit is input.

Sets the LCD monitor to display mirrored images when

shooting facing the subject.

•

VF CONTRAST:

•

Slave unit is in CAMERA mode

Slave unit is in VTR mode and there is no DV signal

The TC GENE. switch on the slave unit is not set to

FREE

4. Set the TC GENE. switch to [FREE] and the TC DISPLAY

Adjusts the contrast of the viewfinder screen.

BLACK & WHITE:

Sets the LCD monitor and viewfinder to black and white

display.

switch to [TC].

•

Adjustments are made on the LCD/VF[4/4] menu screen.

X See page 89.

5. Set to STOP mode or EJECT mode.

•

The slave unit is GY-HD200E

HDV format

6. Press the STOP button for 1 second.

•

LCD CONTRAST:

•

The DV input time code data from the IEEE1394 termi-

nal is displayed in the status display. (When status is in

magnified size, characters are displayed.)

Adjusts the contrast of the LCD monitor.

BLACK & WHITE:

MEMO

„ If slave lock is performed in DV format and is then

switched to HDV format, frame digit may deviate.

•

The screen size of the viewfinder can be changed by

selecting the desired size with the ASPECT item on the

VIDEO FORMAT[1/2] menu screen (4:3 or 16:9).

Sets the LCD monitor and viewfinder to black and white

display.

7. Press the USER1 button to begin slave lock.

(To skip slave lock, press the USER3 button and clear

the status display.)

„ If power is turned off, slave lock is disabled. Perform

slave lock operation again.

„ Slave lock cannot be performed for UB (User’s bit).

„ If the frame rate for the master unit and slave unit is not

synchronized, it will not run properly. Synchronize frame

rate before using.

„ If DROP/NON DROP is not synchronized, it will not run

properly. Synchronize DROP/NON DROP before using.

PREPARATIONS FOR OPERATION

1.Set the IRIS mode switch to M (Manual).

•

ERROR: LOW LIGHT (Insufficient illumination)

Displayed when the illumination is dim. Increase the illumi-

nation and then re-adjust the white balance.

ERROR: OVER LIGHT (Excessive illumination)

Displayed when the light is excessively bright. Decrease

the illumination and then re-adjust the white balance.

2.Set the zoom mode to M (Manual).

Back Focus Adjustment

White Balance Adjustment

3.Open the iris by turning the iris ring.

If the illumination is too strong, reduce it or move to a

darker place.

4.Turn the zoom lever until the lens is at the maximum tele-

It is only necessary to perform this when the lens is attached

for the first time or when focusing is not correct in both the

telephoto and wide-angle positions.

Since the color of light (color temperature) varies depending on

the light source, it is necessary to re-adjust the white balance

when the main light source illuminating the subject changes.

photo position.

5.Bring the subject into focus.

6.Set the lens to maximum wide-angle.

7.Loosen the back focus ring retaining knob.

•

It is easier to adjust back focus when the subject is more

than 3 meters from the camera.

White Balance Adjustment

8.View the same subject and adjust the back focus ring for

The optimal subject for this adjustment is a Siemens star

chart.

the best possible focus.

Two kinds of white balance adjustment results can be stored

in memories AUTO A and AUTO B.

During operation

Result message

9.Repeat steps 4. through 8. about three times for fine

adjustment until the subject remains in focus in both the

telephoto position and the wide-angle position.

Adjustment procedure

4, 6

10.Tighten the back focus ring retaining knob to secure the

1. Set the following switches.

ring.

•

Set the POWER switch to ON.

Set the IRIS mode switch of the lens to A (Auto).

Set the FULL AUTO switch to OFF.

2. Set the ND filter switch according to the current lighting.

Improper object

Insufficient illumination

3. Set the WHT.BAL switch to A or B.

4. Place a white object near the center of the screen under

the same lighting conditions as the target subject and

zoom in to fill the screen with white.

5. Press the AWB (Auto White Balance) button.

“AUTO WHITE A, B OPERATION” is displayed in the view-

finder while the auto white balance adjustment circuit operates.

When correct white balance is obtained, the approximate

color temperature is displayed together with “AUTO

WHITE A, B OK” for about 5 seconds.

Excessive illumination

CAUTION

•

Do not adjust using any highly reflective objects, such as

metal, etc., as this may result in improper white balance

adjustment.

Iris mode switch (7 on page 10)

•

The FAW (Full Auto White balance) function cannot pro-

vide optimum white balance with a subject outside the

FAW adjustment range, for example when it contains

only a single color or not enough white color.

The accuracy of the FAW (Full Auto White balance) is

inferior to that of the Auto white balance.

When the power is turned on with the FAW mode

selected, it takes about 10 seconds for the FAW adjust-

ment to be completed.

•

7, 8, 10

ND filter

Do not shoot within this interval.

WHT.BAL

switch

POWER switch

AWB button

Full Auto White Balance (FAW)

MEMO

Fine-tune red and blue to match the white adjusted in white

balance in WHITE PAINT<R>/ on the WHITE BAL-

ANCE menu screen. X See page 82.

The FAW function adjusts the white balance value automati-

cally as the lighting condition changes.

Siemens star chart

This mode is convenient when you have no time to adjust the

white balance or when the camera is moved frequently in

and out of places under different lighting conditions.

„ Setting procedure

Error messages

If the adjustment ends abnormally, an error message, as

described below, blinks for about 5 seconds.

The FAW function can be activated with the FAW item on

the SWITCH MODE menu screen. The FAW function can

be allocated to one of the white balance switching

switches A, B, or PRESET.

•

NG: OBJECT (Improper object)

Displayed when there is not enough white color on an

object or the color temperature is not suitable.

Replace the color temperature conversion filter or use

another white object and re-adjust the white balance.

X See page 83.

PREPARATIONS FOR OPERATION

SETTING AND ADJUSTMENTS BEFORE SHOOTING

Setting in the WHITE BALANCE screen is performed as fol-

lows.

4.Turn the SHUTTER dial, change the setting and push the

SHUTTER dial.

White Shading Adjustment

Setting the Video Format

•

The setting stops flashing and is temporarily set.

Move the cursor (K) to the EXECUTE item and EXE-

CUTE flashes.

„ Selecting an item

Turn the SHUTTER dial to align the cursor (j) with the

desired item, and press the SHUTTER dial.

5.Push the SHUTTER dial.

•

The item is selected and the setting value blinks.

•

“REBOOT! SYSTEM CHANGE” is displayed on the

screen and after a few seconds the system is reboo-

ted.

It is necessary to perform this adjustment to the camera

when attaching a lens that is different from the previously

attached lens.

Even if white balance is achieved in the middle of the screen,

it may not be achieved at the top and bottom of the screen.

Greens and magentas may be colored. This is due to char-

acteristics of the lens. Correcting this phenomenon is called

White Shading Adjustment.

Set the video format using the FRAME RATE item and the

REC item on the VIDEO FORMAT menu screen.

„ Changing the setting value

Turn the SHUTTER dial to change the blinking value. When

the SHUTTER dial is pressed, the value stops blinking and

the setting is changed.

Setting the FRAME RATE Item

2 Perform the above steps to set SHADING to MANUAL.

3 Select LEVEL R, LEVEL G, LEVEL

and press the

1. Press the STATUS button for at least 1 second.

SHUTTER dial.

•

The TOP MENU screen is displayed.

SHUTTER dial

Perform this after adjusting white balance.

White shading adjustment is performed on the WHITE BAL-

ANCE menu screen.

•

The setting value for the selected LEVEL blinks and

becomes available for changing.

4 Change the setting values for LEVEL R, LEVEL G, and

LEVEL B with the SHUTTER dial while referring to the

monitor.

When setting values are increased, colors at the bottom

of the screen are suppressed and the top is enhanced.

LEVEL R: Adjusts reds.

LEVEL G: Adjusts greens.

LEVEL B: Adjusts blues.

<Range: -128 to +127>

Adjustment procedure

1. White balance the camera.

USER

SHUTTER

2. Set the camera’s lens controls as follows:

a.Set the IRIS opening to F4 or higher number.

b.In the case of a zoom lens set the ZOOM at the center

of its range.

ND FILTER

Setting the REC Item

Set the REC item using the same steps as for the FRAME

RATE item.

3. Shoot a uniformly lit white sheet of paper and fill the mon-

STATUS

MEMO

itor screen with it.

5 Press the SHUTTER dial after changing the setting val-

•

If you change the FRAME RATE item setting, the system

is rebooted.

The synchronous video signal is momentarily disturbed

when the REC item setting is switched.

We recommend the following settings for REC item (in

HDV format).

ues to save in the memory.

4. Set the monitor CHROMA level to maximum.

6 Press the STATUS button to return to the normal screen.

STATUS button

5. Check the color of the monitor screen. If the top and the

bottom of the monitor screen are white then no adjust-

ment is necessary. If the top of the monitor screen is

greenish and the bottom is reddish or if the top is reddish

and the bottom is greenish then continue with this adjust-

ment.

8.When white shading adjustment is completed, adjust

white balance again.

X See “White Balance Adjustment” on page 51.

2. Turn the SHUTTER dial and bring the cursor (K) to the

VIDEO FORMAT.. item and press the SHUTTER dial.

•

The VIDEO FORMAT[1/2] menu screen is displayed.

When recording images with a lot of motion:

Set to HDV60p or HDV50p

6. Adjust the LEVEL G in the SHADING menu item to mini-

mize the color difference between the top and bottom of

the screen.

When recording images with little motion:

Set to HDV30p or HDV25p

CAUTION

•

If the lens setup is incorrect, the white shading adjust-

ment might result in over compensation. When perform-

ing this adjustment, set the lens to the recommended

settings. Do not open the lens IRIS beyond F4; do not

set a telephoto lens to its extreme wide position or tele-

photo position.

7. It is recommended that only LEVEL G be adjusted.

1 Display the WHITE BALANCE menu screen.

Follow the steps in “Setting Menu Screens” on page 72

and proceed as follows.

MENUrCAMERA PROCESS[1/2]rCAMERA PRO-

CESS[2/2]rADVANCE PROCESSrWHITE BALANCE

•

White shading occurs due to the optical characteristics of

the mounted lens, it is not a camera malfunction.

3. Turn the SHUTTER dial and bring the cursor (K) to the

FRAME RATE item and press the SHUTTER dial.

•

The setting for the selected item flashes and can be

changed.

“CHANGE THE SYSTEM” is displayed on the screen.

SETTING AND ADJUSTMENTS BEFORE SHOOTING

MEMO

ASPECT item

4:3

You can select the normal input level for MIC and MIC+48V

in the INPUT1, 2 MIC REF. item on the AUDIO/MIC[1/2]

menu screen.

4:3 TV

Camera Settings

Audio Input Signal Selec-

tion

1. Set the switch positions.

A. [GAIN] switch: Set to L ( 0 dB).

B. [WHT. BAL] (Auto White Balance) switch: Set to A or

This device is provided with the INPUT1 connector and the

INPUT2 connector for audio input.

Select the audio from the INPUT1 connector or the INPUT2

connector using the CH-2 INPUT switch for the audio to be

recorded in CH-2.

16:9 TV

Adjusting Audio during Recording

For each audio channel, use the CH-1/CH-2 AUDIO

SELECT switch to select whether the audio level adjustment

should be set to AUTO mode or MANUAL mode.

2. Set the lens’ iris mode switch to “A” (Auto iris side).

3. Select the ND filter.

ND FILTER

Suitable Location

16:9

4:3 TV

„ Adjusting the audio input level control

The audio input level can be adjusted manually when this device

is in the record, record-standby or stop mode.

Selecting the CH-2 channel input

connector

OFF OFF

Indoors, dark outdoors

1/4ND

Outdoors under clear sky

1/16ND

Outdoors under extremely clear sky

1.Set the CH-1/CH-2 AUDIO SELECT switch of the chan-

nel whose audio level that you want to adjust manually to

MANU.

Select using the CH-2 INPUT switch.

4. Set the shutter speed to OFF with the SHUTTER dial.

[SQUEEZE]

4:3 TV

INPUT1

: Inputs the audio from the INPUT1 connector

into CH-2.

INPUT2

: Inputs the audio from the INPUT2 connector

into CH-2.

CH-2 INPUT switch

Monitor

speaker

[LETTER]

16:9 TV

MONITOR SELECT FULL AUTO switch

switch

VTR indicator

MONITOR

volume

AUDIO INPUT

VF BRIGHT

switch

USER

•

In DV mode, selection of SQUEEZE and LETTER is not

possible. The screen display mode becomes SQUEEZE.

USER

ND FILTER

LCD BRIGHT

CAM/VTR

AUDIO SELECT

CH-1

CH-2

AUDIO SELECT

CH-1

CH-2

DISPLAY

GENE.

DISPLAY

GENE.

FREE

AUTO

MANU

FREE

MEMO

AUTO

MANU

REC

STATUS

REGEN

STATUS

REGEN

WHT.BAL

•

When you set the REC item on the VIDEO FORMAT[1/2]

menu to HDV format, the ASPECT item is fixed at 16:9

and “[16:9]” is displayed.

If the above applies, you can set to display the image in

the style of 4:3 televisions.

X See “DOWN CON. [HDV]” on page 75.

In the SAFETY ZONE item on the LCD/VF[1/4] menu

screen, you can display the safety zone for a standard

screen as well as a 16:9 screen in the viewfinder or LCD

monitor.

AUTO

CH-1

AUTO

CH-2

WHT.BAL

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

AUDIO

LEVEL

OFF

POWER

REC

POWER

REC

CH-1 audio input

level volume

CH-1/CH-2

AUDIO SELECT switch

CAM/VTR button

MEMO

CH-2 audio input level

volume

The audio from the INPUT1 connector is also input into CH-

1 regardless of the setting.

2.Rotate the audio input level control corresponding to the

Screen Size (4:3/16:9)

Mode Selection

audio input level to be adjusted.

•

Adjust so that the peak level does not exceed the –3 dB

point when a loud sound is input.

X See page 86.

Selecting the audio signal input

•

When the ASPECT item is set to 4:3, the screen that is

displayed may differ depending on the 16:9 television

you are using.

STATUS 1 screen

Select the sound to be input to the INPUT1 or INPUT2 con-

nector using the AUDIO INPUT switch.

The setting is made for each of INPUT1 or INPUT2 connector.

The screen size of recorded images can be selected with the

ASPECT item on the VIDEO FORMAT[1/2] menu screen.

X See page 75.

To record using the standard screen, set ASPECT to 4:3.

To record using the 16:9 screen, set ASPECT to 16:9.

LINE

: Set to this position when connected to audio

equipment, etc.

The reference input level is +4 dBs.

•

MIC

: Set to this position when using

microphone.

dynamic

MIC+48V : Set to this position when a microphone (phan-

tom microphone) requiring +48

DC power

supply is connected.

Audio level

CAUTION

Indicator level (reference)

When connecting a component that does not require +48 V

power supply, make sure that the switch is not set to

MIC+48V before the component is connected.

SETTING AND ADJUSTMENTS BEFORE SHOOTING

SHOOTING OPERATION

•

The loudspeaker or earphone outputs an alarm tone in the

MEMO

case of an abnormal condition occurring in this device.

An alarm tone is also output when the tape end is reached

or when the battery is running down.

Audio Input Signal Selection

(Cont’d)

The way the FRONT TALLY and the BACK TALLY lamps

flash differ depending on what you set in the FRONT

TALLY and BACK TALLY items on the OTHERS[1/2] menu

screen. X See page 93.

Basic Recording Opera-

tion

Do not increase the audio monitoring volume exces-

sively; otherwise howling with the camera microphone

may occur.

MEMO

1. Set the POWER switch to ON.

CAUTION

MEMO

•

This device turns on in camera mode.

•

When AUDIO LIMITER in the AUDIO/MIC[1/2] menu

screen is set to ON, the AUDIO LIMITER functions in

manual adjust mode. Recording level is suppressed

when excessive audio is input.

•

This device enters the stop mode automatically at TAPE

•

When connecting a stereotype earphone, make the fol-

2. Start recording.

END. If this mode continues for

switches to the tape protect mode.

minutes, the mode

lowing settings to output stereo sound.

1Set the MONITOR SELECT switch to BOTH.

Press the REC/VTR trigger button on this device to start

recording.

See “OTHERS[1/2] Menu Screen” on page 93.

X See “AUDIO LIMITER” on page 84.

2Set the AUDIO MONITOR item on the AUDIO/MIC[2/2]

Once recording has started, the FRONT TALLY lamp and

BACK TALLY lamp light red.

(LONG PAUSE TIME item)

•

The reference level for audio recorded on the tape can

be set with the AUDIO REF. LEVEL item on the AUDIO/

MIC menu screen. (–20 dB or –12 dB) The level will

change for both CH-1 and CH-2.

menu screen to STEREO.

•

If the REC/VTR trigger button is pressed very quickly

and repeatedly, or the POWER switch is moved immedi-

ately after the trigger button is pressed, this device may

not enter the record mode.

•

When AUDIO MONITOR item on the AUDIO/MIC[2/2]

menu screen is set to “STEREO”, only the audio of CH-1

is output from the monitoring speaker.

The volume of the alarm tone is set with the ALARM VR

LEVEL item on the OTHERS[1/2] menu screen. (OFF/

LOW/MIDDLE/HIGH)

FOCUS ASSIST button

FRONT TALLY lamp

To remedy this condition set the POWER switch to OFF

and wait for 5 seconds or more before turning the power

on again.

CAUTION

•

When the AUDIO INPUT switch is set to MIC, be sure to

check that the microphone is connected to the INPUT1/2

connector. If the microphone is not connected, increasing the

audio level could cause noise from the input connector to be

recorded on the tape. When the microphone is not con-

nected to the INPUT1/2 connector, set the AUDIO INPUT

switch to “LINE” or turn down the audio level control.

In the FULL AUTO mode, the audio level volume cannot

be adjusted with the audio level controls on the CH-1 and

CH-2.

•

A neat transition to the next recorded scene cannot be

guaranteed if

POWER switch or DC power supply OFF, or by removing

the battery pack.

recording is ended by turning the

•

Trial-shooting is always recommended before recording

important events to confirm the recording is satisfactory.

The microphone may pick up the sound of the lens’ iris if

the iris is changed abruptly or the iris is manually moved

abruptly during recording.

•

Monitoring Audio during Recording

About the QUICK REC START Mode

If the REC/VTR trigger button is pressed immediately after

the videocassette is inserted, the mode becomes the

QUICK REC START mode that enables quick start of

recording.

The audio input during recording, in record-pause or stop

mode can be monitored through the monitoring speaker or

earphone.

REC trigger button

POWER switch

However, when shooting starts in the middle of the tape, a

blank space appears as the new scene will not be linked

smoothly with the previous image.

Also, the time code does not continue. (Some overlap may

also occur.)

FOCUS ASSIST

button

REC trigger button

BACK TALLY lamp

About the Focus Assist Function

When you press this button during shooting, the area of

focus is displayed in blue, red or green, making it easy to

focus accurately.

X See “LCD/VF[1/4] Menu Screen” on page 86.

You can also set this function from the RET button.

X See “SWITCH MODE Menu Screen” on page 83. (LENS

RET item)

When FOCUS ASSIST on the LCD/VF[1/4] menu screen is

set to ACCU-FOCUS, ACCU FOCUS functions with FOCUS

ASSIST. This makes focusing with shallower depth of field

easier. ACCU FOCUS automatically turns OFF after approxi-

mately 10 seconds. X See page 86

PHONES jack

RET button

VTR trigger button

•

Select the audio channel to be monitored using the MONI-

TOR SELECT switch.

: The sound input to the CH-1 channel is output.

BOTH : The sound input to the CH-1 and CH-2 chan-

nels is output mixed.

CH-1

CH-2

: The sound input to the CH-2 channel is output.

The MONITOR volume control adjusts the monitoring vol-

ume.

SHOOTING OPERATION

•

The recorded contents can be checked on the LCD moni-

tor, in the viewfinder or on a monitor connected to the

video signal output connectors.

Basic Recording Operation

(Cont’d)

HEADER REC Function

1.In the record-standby mode, press the RET button on the

camera lens section.

When the REC/VTR trigger button is pressed while the STOP button is pressed, this function first records the color bar video and

the test tone (1 kHz sine-wave) of the built-in signal generator at the beginning of the tape. Then it records the black video signal

and the mute audio signal for the duration specified in advance. When the recording is completed, this device enters the Record-

Standby mode. The time code value at the Record-Standby position becomes the time code specified in advance. (HEADER

REC function)

If the Record-Standby Mode Contin-

ues

•

Settings related to the HEADER REC function, such as whether the HEADER REC function should be enabled, the HEADER

REC execution duration, and the time code value setting when the HEADER REC recording is completed, etc., are made on

the HEADER REC menu screen.

The HEADER REC function is executed under the following circumstances:

CAM/VTR button: Set to CAM mode.

Setting the time before the tape protection mode is engaged

The time before the tape protection mode is engaged from

the record-standby mode can be set to 5 minutes or 3 min-

utes with the LONG PAUSE TIME item on the OTHERS[1/2]

screen menu. X See page 93.

•

In the Record-Standby or Stop mode

1. RET button

When the record-standby mode has continued for about 5

minutes or 3 minutes, this device automatically stops drum

rotation in order to protect the tape. (Tape protect mode)

In the tape protect mode, STOP is shown as the VTR

mode indication on the LCD monitor and in the viewfinder

screen. (STATUS 1 screen)

Record-Standby mode

Tape beginning

HEADER REC

Normal recording

(Example) 30 sec

Color bar video signal

Test tone (1 kHz)

Black video signal

Mute audio (No sound)

•

The tape rewinds and about 6 seconds of the content

recorded in DV format is played back, and about 8 sec-

onds of the content recorded in HDV format is played

back. After playback, this device returns to standby

mode at the position on the tape where the RET button

was pressed.

(Setting range: 0 to 99 sec)

Time code, user’s bits recording

Time code:

User’s bits:

„ If you continue to hold down the RET button, up to about

18 seconds of content recorded in DV format and up to

about 20 seconds of content recorded in HDV format can

be rewound and played back.

The value specified on the HEADER

REC menu screen.

(Example) 00:00:00:00

The value specified on the HEADER

REC menu screen- HEADER REC time.

(Example) 23:59:00:00

The value specified for the UB

DATA item on the HEADER REC

menu screen.

The value specified for the UB

PRESET item on the TC/UB/

CLOCK menu screen.

(only when set to REC RUN or

FREE RUN mode)

VTR mode indication

•

Pressing the REC/VTR trigger button during playback

will put this device in REC standby mode. The camera

will automatically return to recording mode after play-

back.

„ HEADER REC menu screen contents

„ To start recording from the tape protect mode, press the

REC/VTR trigger button.

Item

Function/Initial Setting

START KEY

Sets whether the HEADER REC operation should be executed when the REC/VTR trigger button is pressed while the

STOP button is pressed.

•

The drum starts rotating, and recording starts after

about 3 seconds.

CAUTION

DISABLE

STOP+REC

HEADER REC operation is not executed.

HEADER REC operation is executed.

•

This function does not work when using RET button is

used as FOCUS ASSIST button.

This function does not work when this device is in the

stop mode.

During recording check, the following indication will

appear if the error rate increases due to head clogging,

etc.

„ To return to the record-standby mode from the tape protect

mode, press the RET button.

TC DATA

Sets the time code value for the point when the Record-Standby mode is engaged following completion of HEADER

REC.

CAUTION

EXECUTE

ZERO PRESET: Resets all time codes to zero “0”.

CANCEL Clears the set time code.

Confirms the set time code.

This function does not work when using RET button is used

as FOCUS ASSIST button.

The frame mode is set depending on the setting in the DROP FRAME item on the TC/UB/CLOCK menu screen.

* The time code value at the point when the Record-Standby mode is engaged may differ some frames from the value

set for this item.

“HEAD CLEANING REQUIRED!” is shown on the LCD

monitor or in the viewfinder. (When the STATUS 0, 1, 4

screen is displayed.)

UB DATA

Sets the user’s bits of the HEADER REC section.

Checking Recorded Contents in

Record-Standby Mode (Recording

Check Function)

EXECUTE

Confirms the set user’s bits.

ZERO PRESET: Resets all user’s bits data to zero “0”.

CANCEL

Clears the set user’s bits.

MEMO

The user’s bits for the normal recording section are set on the TC/UB/CLOCK menu screen.

This function is available only when this device is in the

standby mode.

In standby mode, about 5 seconds of the last part of the con-

tent recorded in DV format can be played back, and about 7

seconds when the content was recorded in HDV format can

be played back.

BARS TIME

Sets the duration (seconds) in which the color bar signal and test tone (1 kHz) is recorded during HEADER REC. (1-sec

steps)

[Initial Setting: 0SEC - 30SEC - 99SEC]

BLACK TIME

PAGE BACK

Sets the duration (seconds) in which the black signal is recorded during HEADER REC. (1-sec steps)

[Initial Setting: 0SEC - 30SEC - 99SEC]

The TC/UB/CLOCK menu screen returns when the SHUTTER dial is pressed.

SHOOTING OPERATION

PLAYBACK MODE

2.While pressing the STOP button, press the REC/VTR

•

When the automatic tracking function is activated at the

start of the playback mode, digital noise may appear in

the playback image.

This device does not allow manual tracking adjustment.

When playing back a tape that was recorded on another

unit, digital noise may appear during playback.

Following loading of the tape, the built-in head cleaner

will emit a sound while operating. This does not indicate

a malfunction.

trigger button.

HEADER REC Function

(Cont’d)

Playback Procedure

•

The tape automatically rewinds to the beginning, and

HEADER REC operation starts from the beginning of

the tape.

•

After HEADER REC recording is performed for the

specified duration only, the Record-Standby mode is

engaged automatically.

During HEADER REC recording, “HEADER REC” is

shown (blinking) on the LCD monitor and in the view-

finder.

•

Recorded pictures can be viewed in the viewfinder, or on the

LCD monitor, or on the monitor connected to the video output

connector.

How to set the HEADER REC menu screen

•

1. Display the HEADER REC menu screen.

The data recorded for the date and time or time code on

the tape can be shown on the screen. To enable or dis-

able the display is selected on the menu screen:

1Select the TC/UB/CLOCK.. item on the TOP MENU

screen.

STOP button

PLAY/STILL button

2Select the HEADER REC item on the TC/UB/CLOCK

Display of date and time : TIME/DATE menu screen

menu screen.

Display of time code

: LCD/VF[1/2] menu screen

TC/UB/CLOCK menu screen

REW button

FF button

Fast-Forward, Rewind

MEMO

During HEADER REC

This device can play back the following two types of video-

cassettes:

„ Press the FF button in the stop mode to fast forward the

tape. Press the REW button in the stop mode to rewind

the tape. (VTR mode only)

•

The menu screen is not displayed during HEADER REC

recording.

•

MiniDV videocassette

DVCAM videocassette

HEADER REC menu screen

“SWITCH TO VTR MODE” is displayed and the function

does not work if the “FF” or “REW” buttons are pressed

when Camera mode is in the stop mode.

Tapes recorded in the LP mode cannot be played back.

3.After HEADER REC recording is completed and the

Record-Standby mode is engaged, normal recording

starts when you press the REC/VTR trigger button.

2. Setting the HEADER REC menu screen.

1. Set the POWER switch to ON.

„ Press the STOP button to stop fast forwarding or rewind-

ing.

1Select the menu item.

2. Set this device to the VTR mode.

•

When the TC GENE. switch is set to either REC or

REGEN, the time code value at the start of the

HEADER REC menu screen.

Rotate the SHUTTER dial to align the cursor (K) with

the item to be set, and then press the SHUTTER dial.

The setting area of the selected item starts blinking.

Press the CAM/VTR button to turn on the VTR indicator.

Playback is also possible in the Camera mode.

Playback operation becomes possible when the STOP

button is pressed to set the VTR operation mode indi-

cator to indicate STOP.

MEMO

•

When the tape approaches the end during fast forward-

ing or rewinding, the tape speed decelerates to protect

the tape.

The time required for fast forwarding and rewinding may

become longer when used in a cold environment. This is

not a malfunction.

MEMO

2Changing the setting value.

Rotate the SHUTTER dial to change the setting, and

then press the SHUTTER dial.

•

To stop during HEADER REC operation, press the REC/

VTR trigger button or the STOP button.

The HEADER REC menu screen cannot be opened dur-

ing HEADER REC recording.

HEADER REC operation is accepted even during load-

ing of the cassette tape.

The test tone (1 kHz sine-wave) recorded in the color bar

section will be recorded unrelated to the setting for the

TEST TONE item on the AUDIO/MIC[1/2] menu screen.

The time code preset on the TC/UB/CLOCK menu

screen becomes invalid when HEADER REC recording

is performed.

The user’s bits following completion of HEADER REC

recording will be the user’s bits value set on the TC/UB/

CLOCK menu screen.

3. Load the recorded videocassette correctly.

•

When the videocassette is loaded, this device enters

the Stop mode.

4. Open the operation cover on the upper section of this

device.

Slide the operation cover to the side to open.

5. Press the PLAY/STILL button.

•

Playback starts.

•

6. Press the PLAY/STILL button to stop playback tempo-

rarily.

•

This device enters the still mode.

„ Press the FF button in the play mode or still mode to

search the tape in the forward direction. Playback takes

place while fast forwarding.

Pressing the REW button executes search of the tape in

the reverse direction. Playback takes place while rewind-

ing.

(Each press on the button switches the speed to ×2, ×5,

and ×10.)

„ Press the PLAY/STILL button to resume normal playback.

„ Press the STOP button to stop.

7. To re-start playback, press the PLAY/STILL button.

Cursor

Item

Set value

8. To stop playback or the still mode, press the STOP but-

The running of the time code following completion of

HEADER REC recording will be in accordance with the

setting of the TC GENE. switch.

„ In the case of the TC DATA item and the UB DATA

item, the blinking digit position moves when the SHUT-

TER dial is pressed. When the SHUTTER dial is

rotated, the value of the blinking digit changes. After all

the digits have been set and the SHUTTER dial is

pressed, EXECUTE starts blinking. Press the SHUT-

TER dial once more to confirm the set value.

ton.

MEMO

FREE RUN

: Continuous running.

•

In the VTR mode, the camera image is not output on the

LCD monitor, in the viewfinder or through the video out-

put connector.

REC RUN or REGEN: Runs only during REC.

Camera images are not output to the LCD monitor, view-

finder or video output during REW mode when the

HEADER REC operation begins.

•

When the still picture mode or stop mode has continued

for a while, this device automatically switches to the tape

protect mode.

3. To terminate the setting, press the STATUS button.

MEMO

•

To output sound during the search, set the SEARCH

AUDIO [DV] item on the AUDIO menu screen to ON.

Block noise may appear in the picture or the image may

freeze during the search.

Tape protect mode : Drum rotation is stopped in order to

protect the tape.

Executing the HEADER REC Function

The START KEY item on the HEADER REC menu screen

should be set to STOP+REC.

•

Noise may appear in the picture in the still mode.

1. Load the cassette and engage the Record-Standby mode

or the Stop mode.

PLAYBACK MODE

USING EXTERNAL COMPONENTS

1.Display the AUDIO menu screen.

Displaying Alarms

Select the AUDIO item on the TOP MENU screen.

•

CHANGE 1394 SWITCH

Outputting Audio

Connecting the Video

Signal Cables

2.Set the AUDIO menu screen.

Displayed when the setting for the input/output video format

from the IEEE1394 connector and the setting for the

IEEE1394 switch are different.

•

PB AUDIO CH [DV] Items

CH1/2

: To reproduce the sound (CH-1, CH-2)

recorded during shooting.

Set the IEEE1394 switch so it matches the video format.

MIX

: To reproduce the sound recorded during

shooting (CH-1, CH-2) and the after-

recorded sound (on CH-3 and CH-4)

simultaneously.

Setting

Connecting the IEEE1394 Cable

Confirm that this device is in the VTR mode.

(VTR indicator: On)

To reduce the emission of unwanted radio waves, be sure to

attach the provided clamp filter as shown in the figure below.

CH3/4

: To reproduce the sound after-recorded

on CH-3 and CH-4.

C H A N G E 1 3 9 4 S W I T C H

•

Attach the clamp filter as close to this device as possible,

as shown in the figure.

Set the IEEE1394 switch on the left panel of this device.

AUDIO OUT connector

PB AUDIO CH [DV]

CH-1

CH1

CH-2

CH2

CH1/2

MIX

: DV format

MONITOR

SELECT switch

HDV

: HDV format

VTR indicator

CH1+CH3

CH3

CH2+CH4

CH4

CH3/4

IEEE1394 switch

For HDV format, audio is output to CH1 and CH2 no matter

the settings.

Clamp filter

VF BRIGHT

USER

ND FILTER

3.Either of the following operations returns you to the nor-

LCD BRIGHT

CAM/VTR

SHUTTER

dial

mal screen.

AUDIO SELECT

CH-1

CH-2

DISPLAY

GENE.

FREE

AUTO

MANU

REC

•

Press the STATUS button

STATUS

REGEN

WHT.BAL

Wind once

AUTO

CH-1

AUTO

CH-2

AUDIO

LEVEL

STATUS

button

•

Return to the TOP MENU screen, select the EXIT item

and press the SHUTTER dial.

OFF

POWER

REC

MEMO

CAM/VTR button

AUDIO menu screen

The DV format is capable of recording up to 4 channels

when the 12-bit, 32 kHz sampling frequency is employed.

This device records audio on the two channels CH-1 and

CH-2. (4-channel recording is possible in the case of DV

input.)

When this device is used for playback of a tape that was

recorded on another unit with audio recorded on the CH-3

and CH-4 channels, the PB AUDIO CH [DV] item on the

AUDIO menu screen must be set.

CAUTION

When connecting the IEEE1394 cable from/to Camcorder,

VCR and other IEEE1394 device, make sure the following

instructions, otherwise the IEEE1394 circuit device may be

destroyed.

After-recording on the CH-3 and CH-4 channels is not pos-

sible.

•

Turn the power of both devices OFF and connect the

IEEE1394 cable.

•

Do not insert incorrectly (in reverse) the IEEE1394 cable

end to IEEE1394 port of both devices.

„ Earphone terminal output audio

Audio output is as shown in the table below depending on

the MONITOR SELECT switch and AUDIO MONITOR

and PB AUDIO CH [DV] settings on the AUDIO menu

screen.

PB AUDIO CH [DV]

MONITOR

CH1/2

MIX

CH3/4

SELECT

AUDIO MONITOR

•

Do not connect the IEEE1394 cable under the condition

of static electricity.

Turn the power of both devices OFF when changing the

IEEE1394 switch from/to HDV/DV.

CH-1

L/R: CH1

L/R: CH1+CH3

L/R: CH3

BOTH

MIX

L/R: CH1+CH2

L: CH1 R:CH2

L/R: CH1+CH2+CH3+CH4 L/R: CH3+CH4

L: CH1+CH3 R: CH2+CH4 L: CH3 R: CH4

STEREO

CH-2

L/R: CH2

L/R: CH2+CH4

L/R: CH4

In HDV format, you can only select the settings within the bold frame.

USING EXTERNAL COMPONENTS

5.Set the audio output. X See page 62.

5.Set the PB TAPE item on the VIDEO FORMAT menu

screen. X See page 76.

Select whether to automatically detect the playback tape

video format or play back only a particular format.

Normally, use the “AUTO” setting.

Set the AUDIO menu screen. X See page 84.

Dubbing with AV Devices

HDV/DV Dubbing

AUDIO menu screen

VIDEO FORMAT menu screen

By connecting the video signal output terminal and the

AUDIO OUTPUT terminal on this device to an AV device,

analog signal dubbing is possible.

Connecting this device to another video component

equipped with HDV/DV connector (IEEE1394 standard)

using a IEEE1394 cable (optional) enables dubbing of digital

signals with high picture quality and high-quality sound.

1. Connect the cables.

Using this device as the playback unit

(Dubbing to another video)

Composite cable

Component cable

•

PB AUDIO CH [DV] item:

1. Set the IEEE1394 switch on the left panel of this device.

Set the audio channel to be output.

DV : When dubbing in DV format

HDV : When dubbing in HDV format

6.Insert the videocassettes.

6.Insert a videocassette tape.

This device

: Insert the recorded videocas-

2. Connect the IEEE1394 cable.

This device

: Recorded videocassette tape

: Videocassette you want to dub

sette.

Recording unit

: Insert the videocassette to be

dubbed to.

3. Turn both devices on.

Signal flow

7.Press the PLAY/STILL button on this device to start play-

4. Set this device to VTR mode.

back.

7.Press the PLAY/STILL button on this device to start play-

Press the CAM/VTR button. The VTR indicator lights.

Recording unit

back.

8.Start recording on the recording device.

See the recording device user manual for more informa-

tion.

8.Start recording on the recording unit.

For details, see the instructions to the unit used for

recording.

IEEE1394 switch

AUDIO

OUTPUT

connector

9.When dubbing is finished, stop recording on the record-

ing device, press the STOP button on this device, and

stop the playback.

9.When dubbing is completed.

Stop recording on the recording unit, and then press the

STOP button on this device to stop playback.

Signal flow

MEMO

•

Switch the IEEE1394 switch when this device is OFF.

When you dub still images, they are low resolution

images. Noise may also enter the audio.

Operations may differ depending on the features and

specifications of the connected device, and operations or

data exchange may not be possible even if the devices

are connected.

If noise appears on the screen or the audio cuts out, re-

connect the IEEE1394 cable or turn this device on again.

If you turn the power to the device connected to the

IEEE1394 connector on and off or switch the video input,

noise may occur in the audio. If you perform this type of

operation, set the speaker volume as low as possible on

the audio device connected to this device.

2. Turn both devices on.

Recording unit

3. Set this device to VTR mode.

Press the CAM/VTR button. The VTR indicator lights.

•

4. Set the video output.

Set the VIDEO FORMAT menu screen. X See page 74.

VIDEO FORMAT menu screen

•

IEEE1394 cable

Signal flow

CAUTION

•

Set the IEEE1394 switch on both devices to either HDV

or DV.

Start recording after making sure that both devices are

properly connected.

•

Recording may not be possible in some cases even if the

recorder is equipped with a IEEE1394 connector.

•

HDV PB OUTPUT item:

Set the video format to be output from the video output

terminal during tape playback.

•

PB TAPE item:

Select whether to automatically detect the playback tape

video format or play back only a particular format.

Normally, use the “AUTO” setting.

USING EXTERNAL COMPONENTS

MEMO

„ Backup unit

HDV/DV Dubbing

(Cont’d)

•

Place in HDV/DV signal input mode.

Depending on the used component, it may be neces-

sary to set “REMOTE SELECT”.

In HDV format, the UB set in this device is recorded regard-

less of the setting.

Backup Recording

•

When BR-HD50 is used, set the Backup Recording

function to OFF.

Also, set REM SEL HDV/DV in the REMOTE[1/2] menu

of the BR-HD50 to ON or LOC+REM.

Insert the tape and set to STOP or REC PAUSE status.

When Using the GY-HD200U/GY-HD201E

as Recording Unit

(Dubbing From Another Videocassette)

Backup Recording of this Device’s Cam-

era Image and Sound Through the

IEEE1394 Connector

•

CAUTION

This device’s camera image and sound can be recorded for

backup on another component that is equipped with

IEEE1394 connector.

1. Set the IEEE1394 switch on left side of the GY-HD200U/

•

Set the IEEE1394 switch on both devices to either HDV

or DV.

Start recording after making sure that both devices are

properly connected.

If the RET button is pressed during backup recording,

output from the IEEE1394 terminal is stopped, the image

is switched to the image recorded on this device, inter-

rupting the backup recording image.

GY-HD201E.

DV : When dubbing in DV format

HDV : When dubbing in HDV format

Connections

Use this device as the master unit.

2. Connect the units with the IEEE1394 cable.

3. Turn ON both units.

Connect the master unit and the backup unit with

IEEE1394 cable.

4. Place the GY-HD200U/GY-HD201E in the VTR MODE.

Press the CAM/VTR button to turn on the VTR indicator.

TC/UB

5. Set the frame rate.

Operation

IEEE1394 switch

Set the FRAME RATE item (60/30, 50/25, 24) on the

VIDEO FORMAT[1/2] menu to match the HDV/DV signal

frame rate input from the IEEE1394 connector.

X See page 74.

Start and stop of recording on the backup unit takes place in

accordance with the operation of the REC/VTR trigger button

on the master unit.

(Depending on this device or the backup unit, the image,

audio, and/or time code may deviate from what they should

be at the points where the recording is started or stopped.)

IEEE1394 switch

Backup unit

MEMO

•

When the backup recording is started, the “TRIGGER

TO DV” or “TRIGGER TO HDV” indication is shown on

the LCD or in the viewfinder for approx. 3 seconds.

When the Series Recording function of BR-HD50 is

used, this device’s 1394 REC TRIG. item should be set

to OFF.

If the backup device is equipped with a feature to record

time codes input from the IEEE1394 connector (TC

DUPLICATE feature), time code data the same as on the

master side can be recorded.

If the master unit tape is paused or stopped when the

master unit time code running mode is in REC RUN

mode, the time code for the slave unit stops.

When using BR-HD50 as a backup device and switching

this device from the playback mode to the record mode,

noise will be noticed on the monitor output screen of BR-

HD50 (backup will be correctly recorded).

Date and Time

Master unit

(this device)

7.Insert the videocassettes.

IEEE1394 cable

Signal flow

GY-HD200U/

GY-HD201E

: Insert the videocassette to be dubbed

to.

Playback unit : Insert the recorded videocassette.

Recording unit

Settings

„ Master unit (this device)

8.Start playback on the playback unit.

For details, see the instructions to the unit used for play-

back.

1. Set the IEEE1394 switch on left side of this device.

DV : When backup in DV format

HDV : When backup in HDV format

Signal flow

IEEE1394 cable

•

The playback picture from the playback unit appears

on the GY-HD200U/GY-HD201E’s LCD monitor and

viewfinder screen.

2. Place in Camera mode.

CAUTION

•

3. Set the 1394 REC TRIG. item on the OTHERS[2/2] menu

•

Set the IEEE1394 switch on both devices to either HDV

or DV.

Start recording after making sure that both devices are

properly connected.

9.Press the REC/VTR trigger button on the GY-HD200U/

screen. X See page 94.

GY-HD201E to start recording.

For HDV mode, set the BACK SPACE [HDV] item.

X See page 94.

•

„ To temporarily pause the recording, press the REC or

VTR trigger button.

„ To restart the recording, press the REC or VTR trigger

button again.

OTHERS[2/2] menu screen

6. Set the time code and user bit recording.

Set the TC DUPLI. item on the TC/UB/CLOCK menu

screen.

10.When dubbing is completed.

Press the REC/VTR trigger button or the STOP button on

the GY-HD200U/GY-HD201E to stop recording, and then

stop playback on the playback unit.

OFF

: Records the TC/UB set in this

device.

: Records the TC/UB for the

IEEE1394 input.

MEMO

Date and time data : Records the data sent from the

playback device in DV format.

Depending on the player, sound may not be heard momen-

tarily from this device when switching modes from STILL to

PLAY.

Records the data of the internal

clock in HDV format.

USING EXTERNAL COMPONENTS

Notes on Using the Remote Control Unit

Remote Control Unit Functions List

SC FINE

RANDOM SHUTTER

VARIABLE SHUTTER LEVEL

SLOW SHUTTER LEVEL

•

When the switch function of this device and the remote

control unit are the same, the remote control switch func-

tion is prioritized.

Connect a Remote Con-

trol Unit (RM-LP55/RM-

LP57)

Function

Action

RM-LP55

BARS [OFF/ON]

RM-LP57

•

FOCUS and ZOOM cannot be adjusted with the remote

control unit.

Shutter speed slightly differs from the value displayed on

this device.

q: Same as RM-LP55

G: Available

CONTOUR [OFF/ON]

CONTOUR V/H LEVEL

IRIS [MANU/AUTO]

IRIS LEVEL

: None

X: Not available

Only when frame rate is 60p, 60i, 30p, or 24p

Only when frame rate is 50p, 50i, or 25p

Set camera switch functions with the remote control unit

(RM-LP55/RM-LP57).

Shutter Speed in 24p Mode

When this device is in 24p mode, shutter speed cannot be

set to 1/60 (U model) or 1/50 (E model) with the remote

control unit.

Even if shutter speed is set to 1/60 or 1/50 with the remote

control unit when in 24p mode, the shutter speed for the

device is 1/48.

IRIS DETECT

Connection

Connect the remote control unit cable to the REMOTE termi-

nal.

WHT.BAL

AUTO1

AUTO2

FAW

PRESET

MANU

•

AUTO WHITE Function

When the device is in VTR mode, during playback or

HEADER REC, the AUTO WHITE function does not work

even if the auto white operation is performed with the RM-

LP55 and RM-LP57.

In the case of the RM-LP55, “LOW LIGHT ERROR” is dis-

played on the LCD screen of the RM-LP55.

AUTO WHITE

MANUAL WHITE BALANCE R/B

LEVEL

Clamp filter

PAINT R/B LEVEL

GAIN

0dB

6dB

Wind once

9dB

12dB

LOLUX

–3dB

–6dB

ALC+EEI

ALC

REMOTE

RM-LP55

•

Attach the clamp filter included with the remote control unit

to the remote cable.(The clamp filter can be substituted

with the clamp filter included with this device.)

NEGA [OFF/ON]

SHUTTER

NORMAL

1/100

G *

Consult your JVC dealer if you do not have a clamp filter.

1/120

CAUTION

1/250

Turn the power OFF when connecting.

1/500

1/1000

1/2000

1/4000

1/10000

EEI

Operation

1. Turn the device ON.

2. Turn ON the OPERATE switch on remote control unit to

activate the remote control unit.

V.SCAN

See page 69 for details on functions that can be operated

with the remote control unit.

ZOOM

FOCUS

HI-RESO [OFF/ON]

MASTER BLACK LEVEL

GAMMA [OFF/ON]

GAMMA MASTER LEVEL

KNEE MASTER LEVEL

TITLE [OFF/ON]

TITLE POSITION

TITLE CLEAR

H PHASE

SC COARSE [0°/90°/180°/270°]

MENU SCREENS

Menu Screen Configura-

tion

The Menu Screen consists of multiple layers of menu screens as shown below. The menu screen to be set is selected from the

TOP MENU in accordance with the function or purpose.

„ VTR Mode/IEEE1394 Input Mode

(HDV/DV signal input is possible with the GY-HD200U, GY-HD201E.)

The items on the menu screens differ with the Camera mode and the VTR mode. The contents of set items are stored in this

device’s memory and are retained even when the power is turned off.

The FILE MANAGE menu screen can be used to store the menu setting contents on this device or SD memory card.

„ Camera Mode

TOP MENU screen (VTR)

TOP MENU screen (CAM)

MENU SCREENS

4.Select the menu screen to be set.

Rotate the SHUTTER dial to align the cursor (K) with the

menu screen to be set, and then press the SHUTTER

dial.

Setting Menu Screens

TOP MENU Screen

•

The selected menu screen appears.

Item

Setting

Make the settings while observing the LCD monitor or the

viewfinder screen.

Different menu screens are displayed depending on whether this device is in the Camera mode or in the VTR mode. In the VTR

mode, the CAMERA OPERATION, CAMERA PROCESS and SWITCH MODE menu screens are not displayed.

If the ANALOG OUT CHAR. item on the OTHERS[1/2]

screen is set to ON, the menu screen can also be viewed on

a monitor connected to the video signal output connector.

Item

Function

VIDEO FORMAT..

Displays the menu screen for setting the video format for shooting and playing back video.

Camera mode: It consists of two screens.

1. Set the POWER switch to ON.

VTR mode

: It consists of one screen.

• The cursor (K) does not move to this item when this device is recording.

2. Set the mode of this device with the CAM/VTR button.

CAMERA OPERATION.. Displays a menu screen for setting the operation mode for camera shooting.

• This item is only displayed in the Camera mode.

(Camera mode or VTR mode)

3. Press the STATUS button for 1 second or longer.

CAMERA PROCESS..

Displays a menu screen for adjustments of the picture quality of the camera image.

It consists of two screens.

The ADVANCED PROCESS menu screen, WHITE BALANCE menu screen, and SKIN COLOR ADJUST screen can

be displayed through the CAMERA PROCESS menu screen.

• This item is only displayed in the Camera mode.

• The cursor (K) does not move to this item when this device is in VTR mode (PLAY, STL, FWD, REV).

•

The TOP MENU screen appears.

VIDEO FORMAT[1/2] menu screen

USER1 USER2 USER3 button

5.Select the menu item on the menu screen.

Rotate the SHUTTER dial to align the cursor (K) with the

item to be set, and then press the SHUTTER dial.

SHUTTER dial

•

The setting area of the selected item starts blinking,

and the setting can now be made.

USER

SWITCH MODE..

AUDIO/MIC..

Displays the menu screens related to the camera switch functions.

• This item is only displayed when in camera mode.

SHUTTER

ND FILTER

6.Change the setting.

Displays a menu screen related to audio.

Camera mode: It consists of two screens.

VTR mode

Rotate the SHUTTER dial to change the setting, and then

press the SHUTTER dial.

: It consists of one screen.

•

The setting area stops blinking and the setting is

entered.

• In VTR mode, the screen changes to the AUDIO menu screen.

• The cursor (K) does not move to this item when this device is recording.

STATUS

„ To change multiple items, repeat the procedures in steps

5. and 6. above.

LCD/VF..

Displays a menu screen for selecting whether to display characters on the LCD monitor or in the viewfinder, and for

adjustments of the picture quality of LCD monitor.

Camera mode: It consists of four screens.

7.Return to the TOP MENU screen.

STATUS button

VTR mode

: It consists of two screens.

Rotate the SHUTTER dial to align the cursor (K) with the

PAGE BACK item, and then press the SHUTTER dial.

„ To change settings on other menu screens, repeat the

procedures in steps 4. to 7. above.

TC/UB/CLOCK..

Displays a menu screen for setting the time code, user’s bit data, date and time.

The ways that the date and time are recorded together with the display style are set here.

The TIME/DATE menu screen and CLOCK ADJUST screen can be displayed through the TC/UB/CLOCK menu

screen.

Cursor

Menu screen

„ To save the set contents in FILE, select the FILE MAN-

AGE menu screen and perform the operations for saving

to file.

• The cursor (K) does not move to this item when this device is recording.

OTHERS..

Displays a menu screen for setting other functions and to display the hour meter.

It consists of two screens.

X See “FILE MANAGE Menu Screen” on page 96.

FILE MANAGE..

Displays the FILE MANAGE menu screen.

8.To return to the normal screen after completing the set-

tings, use either of the following methods.

Press the STATUS button

Saves the menu screen settings as a file on this device or an SD memory card, or reads the menu screen settings

saved in the file. It is also possible to reset the menu settings to default settings or initialize (format) an SD memory

card.

X See “FILE MANAGE Menu Screen” on page 96.

• The cursor (K) does not move to this item when VTR is activated.

Return to the TOP MENU screen and align the cursor (K)

with the EXIT item, and then press the SHUTTER dial.

EXIT

The normal screen returns when the SHUTTER dial is pressed while the cursor is aligned with this item.

TOP MENU screen

MEMO

•

While the menu screen is being displayed, the USER1,

USER2 and USER3 buttons can also perform menu

operations.

USER1 button : Raises the cursor (K)/Changes the set-

ting

USER2 button : Lowers the cursor (K)/Changes the set-

ting

USER3 button : Confirms the menu item/Confirms the

setting

•

The menu screen is not displayed when switching

between Camera and VTR mode (VTR indicator

flashes).

MENU SCREENS

VIDEO FORMAT[1/2] Menu

Screen

The VIDEO FORMAT menu screen consists of two screens (1/2 screen, 2/2 screen).

In VTR mode, this screen consists of one screen.

This is not displayed in VTR mode.

Item

Function/Setting (bold characters indicate initial settings)

This is not displayed in VTR mode.

ASPECT*

Sets the screen size for the recording video signal. (Can only be displayed and set in camera mode)

Item

Function/Setting (bold characters indicate initial settings)

Sets the frame rate for shooting.

4:3

16:9

: Outputs the video with an aspect ratio of 4:3.

: Outputs the video with an aspect ratio of 16:9.

FRAME RATE

The resolution in the vertical direction drops compared to 4:3 video.

U model

60/30

50/25

E model

60/30

: Shoots at 480/60i, 720/60p, 720/30p.

: Shoots at 720/50p, 720/25p.

: Shoots at 480/24p (2:3:2:3 pulldown), 480/24p advance mode (2:3:3:2 pulldown), 720/24p.

MEMO

• When the format setting is HDV, the ASPECT item is fixed at 16:9. (“[16:9]” is displayed.)

• The synchronous video signal is momentarily disturbed when the ASPECT item setting is switched.

: Shoots at 720/60p, 720/30p.

: Shoots at 576/50i, 720/50p, 576/25p, 720/25p.

: Shoots at 720/24p.

HDV PB OUTPUT

When playing back an HDV recorded tape, set video format for component output from the Y/PB/PR terminal.

You can set the following depending on the FRAME RATE of the HDV recorded tape.

50/25

CANCEL

EXECUTE

: Cancels the settings.

: Executes the settings.

Setting

NATIVE

Description

FRAME RATE

Outputs the signal being recorded on the tape.

60/30

50/25

MEMO

720P

1080I

NTSC

Converts the signal being recorded on tape to 720p and outputs it.

Converts the signal being recorded on tape to 1080i and outputs it.

Converts the signal being recorded on tape to 480i and outputs it.

• If you change the FRAME RATE item setting, the system is rebooted. X See page 53.

• The cursor (K) does not move to this item when this device is in VTR mode or is ejecting a tape.

60/30

1080I CAMERA*

Selects whether or not to output camera images in HDV1080i signals. HDV1080i signals are output from component

output of the Y/PB/PR terminal. However, they are not recorded on this device.

OFF

PAL

Converts the signal being recorded on tape to 576i and outputs it.

50/25

: No HDV1080i signal is output. Output setting of camera images is based on the REC settings below.

: HDV1080i signal is output. (60/30 Frame rate: 1080/60i, 50/25 Frame rate: 1080/50i)

480/60i or 576/50i signals are output from the VIDEO OUT terminal. (Composite signal)

MEMO

• If you convert video recorded in HDV format to DV format and output it, the colors may change.

• This item is also applied to EE images when HDV signals are input to the IEEE1394 terminal.

• Fixed at NATIVE during DV recorded tape playback or DV signal input.

• ON/OFF is set when the SHUTTER dial is pressed.

MEMO

• Tape recording and IEEE1394 output are not available when this is ON.

• REC item cannot be set when this is ON.

• The cursor is positioned on 1080I CAMERA in the VIDEO FORMAT[1/2] menu screen when this is ON.

• When the FRAME RATE is set to 24, this is fixed to OFF.

DOWN CON. [HDV]

Set the style to display down-converted images in aspect ratio 4:3.

SQUEEZE

: Image that is squeezed horizontally is displayed.

LETTER

: Wide image with the top and bottom blackened is displayed.

MEMO

REC*

Sets the video format for shooting. (Can only be displayed and set in camera mode)

You can set the following according to the FRAME RATE.

This setting is only valid in HDV mode.

In DV mode, the style becomes SQUEEZE regardless of the setting of this item.

Setting

DV-60I

Description

FRAME RATE

PAGE BACK

To display the VIDEO FORMAT[2/2] menu screen, move the cursor to this position and press the SHUTTER dial.

The TOP MENU returns when the SHUTTER dial is pressed with the cursor at this position.

DV format Shoots using a 480/60i signal.

(U model Only)

HDV-HD60P HDV format Shoots using a 720/60p signal.

HDV-HD30P HDV format Shoots using a 720/30p signal.

HDV-HD50P HDV format Shoots using a 720/50p signal.

HDV-HD25P HDV format Shoots using a 720/25p signal.

60/30

50/25

DV-50I

DV format Shoots using a 576/50i signal.

DV format Shoots using a 576/25p signal.

DV format Shoots at 480/24p (2:3:2:3 pulldown).

DV format Shoots at 480/24p (2:3:3:2 pulldown).

(E model Only)

(U model Only)

DV-25P

DV-24P

DV-24PA

(U model Only) 24

HDV-HD24P HDV format Shoots using a 720/24p signal.

CANCEL

EXECUTE

: Cancels the settings.

: Executes the settings.

MEMO

• The synchronous video signal is momentarily disturbed when the REC item setting is switched.

• On the E model, the video format is fixed at HDV-HD24P when the FRAME RATE item is set to “24”. “[HDV-

HD24P]” is displayed.

MENU SCREENS

VIDEO FORMAT[2/2] Menu

Screen

CAMERA OPERATION

Menu Screen

This is not displayed in VTR mode.

The CAMERA OPERATION menu screen is only displayed in the Camera mode.

Item

Function/Setting (bold characters indicate initial settings)

Item

Function/Setting (bold characters indicate initial settings)

PB TAPE

Selects whether to automatically detect the playback tape video format or play back only a particular format.

Normally, use the “AUTO” setting.

For adjusting the image level when using auto iris, “ALC” or “EEI”.

Increase value : Increases level.

AE LEVEL

AUTO

HDV

: During tape playback, the format signal is switched automatically and played back.

: During tape playback, only the part of the tape recorded in DV format is played back.

: During tape playback, only the part of the tape recorded in HDV format is played back.

: During tape playback, only the part of the tape recorded in DVCAM format is played back.

Decrease value : Decreases level.

[Settings: –3, –2 - NORMAL (0) - 2, 3]

ALC MAX

Sets the maximum “ALC” value to automatically change the signal intensity level depending on the brightness.

[Setting: 6 dB, 12 dB, 18 dB]

DVCAM

MEMO

PRESET TEMP.

Sets the basic color temperature when the [WHT.BAL] white balance selector switch c on page 15 is in the PRST

(PRESET) position.

3200K

If you play back a tape containing both DV and HDV formats, the video signal is disturbed when the signal is

switched.

: Sets the basic color temperature to 3200K. (Use for light sources with a low color temperature,

such as halogen lamps.)

SET UP

Selects whether to add a setup signal to the composite signal from the VIDEO OUT terminal.

In DV format, a setup signal can be added to COMPONENT output.

5600K

: Sets the basic color temperature to 5600K. (Use for light sources with a high color temperature,

such as sunlight.)

* You can also select a setup signal in the IEEE1394 signal input mode.

MEMO

0.0%

7.5%

: No setup signal is added.

: A setup signal is added.

This item does not function when the FAW item on the SWITCH MODE menu screen is set to “PRESET”.

Initial settings: U model: 7.5% E model: 0.0%

Smoothens the transition when the [GAIN] switch b on page 15, or [WHT.BAL] switch c on page 15 is switched

over and achieves gradual change in place of sudden change.

SMOOTH TRANS

MEMO

However, the smooth transition function does not function when switching the [GAIN] switch set in ALC, FULL AUTO

ON.

When the FRAME RATE item is set to 50/25, this item is not displayed.

PAGE BACK

When the cursor is in this position, press the SHUTTER dial to the VIDEO FORMAT[1/2] menu screen.

OFF

: Deactivates the smooth transition function.

: Activates the smooth transition function.

Sets whether or not color bars are output. (This is fixed at “OFF” when in FULL AUTO mode)

BARS

OFF

: Color bars are not output.

: Color bars are output.

PAGE BACK

The TOP MENU returns when the SHUTTER dial is pressed with the cursor at this position.

REMOTE appears as the setting value of this item when the remote control unit is connected.

MENU SCREENS

CAMERA PROCESS[1/2]

Menu Screen

CAMERA PROCESS[2/2]

Menu Screen

The CAMERA PROCESS menu screen consists of two screens. (1/2 screen, 2/2 screen)

The CAMERA PROCESS menu screen is only displayed in camera mode.

Item

Function/Setting (bold characters indicate initial settings)

Changes the gain in dark areas. Change this depending on the video signal being shot.

BLACK

Item

Function/Setting (bold characters indicate initial settings)

NORMAL

: Normal status

STRETCH

: Enhances the dark areas of the video so the contrast between light and dark is more visible by

stretching the signal only in the dark areas.

MASTER BLACK

Adjusts the pedestal level (master black) that serves as the reference black.

Increase the number : Raises the pedestal level.

Set elongation level with STRETCH LEVEL below.

Decrease the number : Lowers the pedestal level.

COMPRESS : If the video that was shot is bright overall and lacking in contrast, the gain in the dark areas is com-

pressed, which adds contrast.

[Settings: MIN (–10), –9 - NORMAL (0) - 9, MAX (10)]

DETAIL

Adjusts the contour (detail) sharpness level.

Increase the number : Sharpens the contour.

Decrease the number : Softens the contour.

Set compression level with COMPRESS LEVEL below.

STRETCH LEVEL

COMPRESS LEVEL

WHITE CLIP

The amount of stretching increases from LEVEL1oLEVEL2oLEVEL3oLEVEL4oLEVEL5.

[Settings: LEVEL1, LEVEL2, LEVEL3, LEVEL4, LEVEL5]

OFF

: Does not function.

[Settings: OFF, MIN (–10), –9 - NORMAL (0) - 9, MAX (10)]

When this item is set to “OFF”, “-----” is displayed for the following menu items and they cannot be selected.

The amount of compression increases from LEVEL1oLEVEL2oLEVEL3oLEVEL4oLEVEL5.

[Settings: LEVEL1, LEVEL2, LEVEL3, LEVEL4, LEVEL5]

V/H BALANCE

Sets which contours (details) to sharpen, those in the horizontal (H) direction or those in the vertical (V) direction.

Increase the number : Sharpens H direction.

Decrease the number : Sharpens V direction.

Sets the white clipping point on input video signals with a high luminance level.

108%

100%

: The white clipping point is set at a luminance level of 108%.

: The white clipping point is set at a luminance level of 100%. If the screen is too white at

108%, set it to 100%.

[Settings: H-MIN (–5), –4 - NORMAL (0) - 4, H-MAX (5)]

H FREQUENCY

Changes the horizontal contour compensation frequency for the contours (details). Set this as appropriate for the

subject.

KNEE

Sets whether to run the “knee” function, which compresses video signals over a certain level to render the tonality

in the highlight areas, automatically or manually. Set “MANUAL” when you want to check the bright areas, and adjust

the knee point manually.

LOW

: Enhances low frequency bands.

Use this when shooting subjects with large patterns.

: Enhances middle frequency bands.

AUTO

MANUAL

: Adjusts the knee point automatically, according to the luminance level.

: You can change the luminance level in the “LEVEL” item.

MIDDLE

HIGH

: Enhances high frequency bands.

LEVEL

Sets the start point for knee compression (knee point).

Increase the number : Raises the knee point level.

Decrease the number : Lowers the knee point level.

[Settings: 80%, 85%, 90%, 95%, 100%]

Use this when shooting subjects with small patterns.

V FREQUENCY

Use this when shooting subjects with finely detailed patterns.

Changes the vertical contour compensation frequency for the contours (details). Compensates for distortion when

outputting progressive video to an interlaced monitor.

MEMO

HIGH

LOW

: Enhances high frequency bands.

: Enhances low frequency bands.

When the “KNEE” item is set to “AUTO”, “-----” is displayed and this cannot be selected.

SKIN DETECT

LEVEL

Sets ON/OFF for the skin detail function.

REVERSE PICTURE

DNR

When the lens image is inverted and flipped, set “ROTATE” to record properly.

OFF

: Turns off the skin detail function.

: Turns on the skin detail function. (Softens detected skin color area details.)

OFF

: No inversion.

ROTATE

: Invert lens image.

X See “Using the Skin Detail Function” on page 100.

Selects whether or not to set the noise reduction.

Sets the contour compensation level (amount of softening) for the skin detail function.

This can only be selected when the SKIN DETECT item is set to ON.

The DNR (Digital Noise Reduction) function is applied to the tape recording signal, HD component output signal, and

the IEEE1394 output signal in CAMERA mode.

When camcorder’s picture is noisy, because of low light conditions, you can improve picture’s S/N by turning DNR

on.

–1

–2

–3

: Low contour compensation level (amount of softening)

: Medium contour compensation level (amount of softening)

: High contour compensation level (amount of softening)

OFF

: Noise reduction is not performed.

: Sets noise reduction.

PAGE BACK

To display the CAMERA PROCESS[2/2] menu screen, move the cursor to this position and press the SHUTTER dial.

The TOP MENU returns when the SHUTTER dial is pressed while the cursor is at this position.

MEMO

When the REC item on the VIDEO FORMAT[1/2] menu is set to “DV-60I” or “DV-50I”, “-----” is displayed and this cannot be

selected.

REMOTE appears as the setting value of this item when the remote control unit is connected.

• DNR is not applied in VTR mode or during playback.

• DNR is not applied to composite output signals in CAMERA mode.

• When the DNR is set to ON, the camcorder’s S/N ratio becomes better but the “blurring of moving objects” will

increase.

ADVANCED PROCESS.. Calls up the ADVANCED PROCESS menu screen.

X See “ADVANCED PROCESS Menu Screen” on page 80.

PAGE BACK

When the cursor is in this position, press the SHUTTER dial to return to the CAMERA PROCESS[1/2] menu screen.

REMOTE appears as the setting value of this item when the remote control unit is connected.

MENU SCREENS

ADVANCED PROCESS

Menu Screen

COLOR MATRIX ADJUST

Menu Screen

Item

Function/Setting (bold characters indicate initial settings)

Item

Function/Setting (bold characters indicate initial settings)

CINEMA

OFF

: Turns the function OFF.

: Sets the gamma characteristics and color matrix close to the characteristics of a movie

screen. (The monitor image is movie-quality. This setting is not intended for film output.)

R GAIN

For manually adjusting the shading of the R axis of the color matrix (red and cyan).

Increase the number : Enhances red and cyan.

Decrease the number : Reduces red and cyan.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

MEMO

R ROTATION

G GAIN

For manually adjusting the color phase of the R axis of the color matrix (red and cyan).

Increase the number : Increases yellowishness of red color and bluishness of cyan color.

Decrease the number : Increases bluishness of red color and greenishness of cyan color.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

When this item is set to “ON”, “[CINE]” is displayed for COLOR MATRIX and GAMMA items and cannot be

selected.

COLOR MATRIX

Sets the color matrix.

OFF

: Turns the function OFF.

For manually adjusting the shading of the G axis of the color matrix (green and magenta).

Increase the number : Enhances green and magenta.

Decrease the number : Reduces green and magenta.

STANDARD

CINEMA

: Sets a normal color matrix.

: Sets a color matrix close to the characteristics of a movie screen.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

ADJUST..

GAMMA

When “STANDARD” or “CINEMA” is set for the COLOR MATRIX item, a color matrix can be set individually.

Press the SHUTTER dial to call up the COLOR MATRIX ADJUST menu screen.

X See “COLOR MATRIX ADJUST Menu Screen” on page 81.

G ROTATION

B GAIN

For manually adjusting the color phase of the G axis of the color matrix (green and magenta).

Increase the number : Increases bluishness of green color and reddishness of magenta color.

Decrease the number : Increases yellowishness of green color and bluishness of magenta color.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

Adjusts the gamma curve to determine how black is rendered.

OFF

: No gamma curve correction.

STANDARD

CINEMA

FILM OUT

: Sets a normal gamma curve.

: Sets to appear movie-like when viewing on a TV screen.

: Sets to a setting for recording onto film.

For manually adjusting the shading of the B axis of the color matrix (blue and yellow).

Increase the number : Enhances blue and yellow.

Decrease the number : Reduces blue and yellow.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

MEMO

B ROTATION

PAGE BACK

For manually adjusting the color phase of the B axis of the color matrix (blue and yellow).

Increase the number : Increases reddishness of blue color and greenishness of yellow color.

Decrease the number : Increases greenishness of blue color and reddishness of yellow color.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

When this item is set to “OFF”, “-----” is displayed for the LEVEL item and it cannot be selected.

LEVEL

When “STANDARD”, “CINEMA”, or “FILM OUT” is set for the GAMMA item, a gamma curve can be set individually.

Increase the number : Enhances the tonality of the black. However, the tonality in the bright areas deteriorates.

Decrease the number : Enhances the tonality in the bright areas. However, the tonality in the black areas deterio-

rates.

Press the SHUTTER dial to return to the ADVANCED PROCESS screen when cursor is at this position.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

COLOR GAIN

Adjusts the video signal color level.

OFF

: Sets the video to black and white.

SKIN COLOR ADJUST

Menu Screen

Increase the number : Makes the colors more dense.

Decrease the number : Makes the colors less dense.

[Settings: OFF, MIN (–10), –9 - NORMAL (0) - 9, MAX (10)]

WHITE BALANCE..

SKIN COLOR ADJUST..

PAGE BACK

When the cursor is in this position and you press the SHUTTER dial once, the screen switches to the WHITE BAL-

ANCE menu screen.

When you enter the SKIN COLOR ADJUST screen, the areas where the skin detail function is applied are displayed in color, and

other areas are displayed in black and white.

When the cursor is in this position and you press the SHUTTER dial once, the screen switches to the SKIN COLOR

ADJUST screen.

Item

Function/Setting (bold characters indicate initial settings)

Sets the color used by the skin detail function.

When the cursor is in this position, press the SHUTTER dial to return to the CAMERA PROCESS[2/2] menu screen.

SKIN COLOR DET.

STOP

EXECUTE

: Stops loading the color used by the skin detail function.

: Loads the color used by the skin detail function.

X See “How to Use Skin Detail” on page 99.

SKIN COLOR RANGE

Adjusts the range of skin colors to which the skin detail function is applied.

Adjust as you check the color range.

Increase the number : Widens the range.

Decrease the number : Narrows the range.

[Settings: NARROW (–10), –9 - NORMAL (0) - 9, WIDE (10)]

MEMO

When the COLOR GAIN item is “OFF” on the ADVANCED PROCESS menu screen, only the areas where the

skin detail function is running are displayed using skin colors.

PAGE BACK

When the cursor is in this position, press the SHUTTER dial to return to the ADVANCED PROCESS menu screen.

MENU SCREENS

WHITE BALANCE Menu

Screen

SWITCH MODE Menu

Screen

The SWITCH MODE menu screen is only displayed in camera mode.

Item

Function/Setting (bold characters indicate initial settings)

Item

SHUTTER

Function/Setting (bold characters indicate initial settings)

Sets the fixed value (STEP) for values that can change using the SHUTTER dial on the right panel or the VARIABLE

used when shooting computer monitors.

: Switches the shutter speed using fixed values.

: Set when shooting a computer monitor, etc.

You can set the following using the REC item on the VIDEO FORMAT menu screen. (This is fixed at EEI when in

FULL AUTO mode.)

Adjusts the R (red) component when in AWB (Auto White Balance) mode.

Increase the number : Strengthens the red.

Decrease the number : Weakens the red.

WHITE PAINT<R>

STEP

VARIABLE

[Settings: MIN (–32), –31 - NORMAL (0) - 30, MAX (31)]

MEMO

• You can select this when

is set for the [WHT.BAL] switch

on the right panel of this device.

X See page 15.

Settings can be made for A and B individually. (When “PRESET” is set, “-----” is displayed and this cannot be

selected.)

REC Item

Setting for STEP

Setting for VARIABLE

DV-60I

HDV-HD60P 1/10000

HDV-HD30P

1/7.5, 1/15, 1/30, 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/30.03 - 1/10489.5

• When you press the AWB (Auto White Balance) button and readjust the white balance, WHITE PAINT

becomes “NORMAL”.

DV-50I

1/6.25, 1/12.5, 1/25, 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000,

1/25.04 - 1/10489.5

1/24.01 - 1/10489.5

WHITE PAINT

Adjusts the B (blue) component when in AWB (Auto White Balance) mode.

Increase the number : Strengthens the blue.

Decrease the number : Weakens the blue.

HDV-HD50P 1/4000, 1/10000

HDV-HD25P

DV-25P

[Settings: MIN (–32), –31 - NORMAL (0) - 30, MAX (31)]

DV-24P

DV-24PA

1/6, 1/12, 1/24, 1/48, 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000,

1/4000, 1/10000

MEMO

• You can select this when

is set for the [WHT.BAL] switch

on the right panel of this device.

HDV-HD24P

X See page 15.

Settings can be made for A and B individually. (When “PRESET” is set, “-----” is displayed and this cannot be

selected.)

• When you press the AWB (Auto White Balance) button and readjust the white balance, WHITE PAINT

becomes “NORMAL”.

FAW

Sets the positions to assign the FAW (Full Auto White Balance) function to the [WHT.BAL] white balance selector

switch c on page 15. (Fixed at FAW when in FULL AUTO mode)

NONE

: The FAW function is not assigned.

: Assigns FAW to the A position.

: Assigns FAW to the B position.

: Assigns FAW to the PRESET position.

SHADING

Adjusts white shading.

PRESET

: No white shading adjustment.

GAIN L

GAIN M

GAIN H

USER1

USER2

USER3

Sets the gain value for each position on the [GAIN] sensitivity selector switch b on page 15.

[Setting: 0dB, 3dB, 6dB, 9dB, 12dB, 15dB, 18dB, ALC] (Fixed at ALC in FULL AUTO mode)

Initial values: L: 0dB, M: 9dB, H: 18dB

MANUAL

: Enables white shading adjustment.

X See “White Shading Adjustment” on page 52.

MEMO

You can assign one of the following menu functions to the [USER1/2/3] buttons

on page 14 to each button.

When the SHADING item is set to PRESET, the LEVEL R, LEVEL G, and LEVEL B items cannot be selected.

Set according to the shooting conditions. This is only valid in CAMERA mode.This does not function in VTR mode.

Setting

Description

LEVEL R

LEVEL G

When the SHADING item is set to MANUAL, adjusts the reds of white shading.

Increase the number : Red at the bottom of the screen is suppressed and the top is enhanced.

Decrease the number : Red at the top of the screen is suppressed and the bottom is enhanced.

[Settings: MIN, –127 to –1, NORMAL, 1 to 126, MAX]

NONE

Does not function.

BARS

PRESET TEMP.

Assigns “BARS” item functions in the CAMERA OPERATION menu screen.

Assigns “PRESET TEMP.” item functions in the CAMERA OPERATION menu screen.

X See “CAMERA OPERATION Menu Screen” on page 77.

When the SHADING item is set to MANUAL, adjusts the greens of white shading.

Increase the number : Green at the bottom of the screen is suppressed and the top is enhanced.

Decrease the number : Green at the top of the screen is suppressed and the bottom is enhanced.

[Settings: MIN, –127 to –1, NORMAL, 1 to 126, MAX]

B.STRETCH1

B.STRETCH2

B.STRETCH3

B.STRETCH4

B.STRETCH5

B.COMPRESS1

B.COMPRESS2

B.COMPRESS3

B.COMPRESS4

B.COMPRESS5

Assigns “BLACK” item functions in the CAMERA PROCESS[1/2] menu screen.

X See “CAMERA PROCESS[1/2] Menu Screen” on page 78.

LEVEL B

When the SHADING item is set to MANUAL, adjusts the blues of white shading.

Increase the number : Blue at the bottom of the screen is suppressed and the top is enhanced.

Decrease the number : Blue at the top of the screen is suppressed and the bottom is enhanced.

[Settings: MIN, –127 to –1, NORMAL, 1 to 126, MAX]

PAGE BACK

When the cursor is in this position, press the SHUTTER dial to return to ADVANCED PROCESS menu screen.

REMOTE appears as the setting value of this item when the remote control unit is connected.

AE LEVEL+

AE LEVEL–

Assigns “AE LEVEL” item functions in the CAMERA OPERATION menu screen.

MEMO

Cannot assign to the USER3 button. If you assign these menu functions, assign AE

LEVEL+ to the USER1 button, AE LEVEL– to the USER2 button.

RET

Assigns the normal RET button function.

LOAD FILE

Assigns the function to jump to in the LOAD FILE menu.

X See “FILE MANAGE Menu Screen” on page 96.

LENS RET

Sets the lens RET button functions. (This does not function if there is not RET button on the lens you are using.)

RET

: Functions as a normal RET button.

FOCUS ASSIST

: Functions as the FOCUS ASSIST button.

PAGE BACK

When the cursor is in this position, press the SHUTTER dial to return to the TOP MENU screen.

MENU SCREENS

AUDIO/MIC[1/2] Menu

Screen

AUDIO/MIC[2/2] Menu

Screen

The AUDIO/MIC menu screen consists of two screens (1/2 screen, 2/2 screen).

In VTR mode, the screen changes to the AUDIO menu screen.

This is not displayed in VTR mode.

Item

Function/Setting (bold characters indicate initial settings)

Item

Function/Setting (bold characters indicate initial settings)

AUDIO MONITOR

FAS AUDIO*

Selects whether stereo or mixed audio is output from the PHONES jack when the MONITOR SELECT switch is set

to BOTH.

TEST TONE

Sets whether to output a test audio signal (1 kHz, –20dBFS or –12dBFS) during color bar output.

OFF

: A test audio signal is not output.

: A test audio signal is output.

STEREO

: Stereo audio (CH-1 audio is output to L and CH-2 audio is output to R)

* Outputs only the CH-1 audio from the monitor speaker.

MIX

: Mixed audio (CH-1 and CH-2 mixed audio is output to L and R)

MIC WIND CUT*

Selects whether to cut the lows (low frequency bands) from the audio input signal.

Use this when you want to reduce wind sounds from the microphone.

Selects the recording level adjusting method for FAS (Full Auto Shooting). (CH-1, CH-2)

OFF

: Low frequencies are not cut.

AUTO

: Sets to AUTO.

INPUT1

INPUT2

BOTH

: Only cuts the low frequencies in the audio from the INPUT1 connector.

: Only cuts the low frequencies in the audio from the INPUT2 connector.

: Cuts the low frequencies in the audio from both the INPUT1 and INPUT2 terminals.

SW SET

: Follows settings for the AUDIO SELECT switch.

X See “2 [CH-1/CH-2 AUDIO SELECT] switch” on page 13.

X See “g [FULL AUTO] switch” on page 19.

AUDIO REF.LEVEL

Sets the reference audio level on the tape. (Both CH-1 and CH-2)

SEARCH AUDIO [DV]

PB AUDIO CH [DV]

Selects whether to output audio when searching a tape recorded in DV format. (This also includes slow playback.)

–20dB

: Records with –20 dB as the reference audio level.

: Audio is output.

–12dB

: Records with –12 dB as the reference audio level.

OFF

: Audio is not output.

Set this if you are playing back the recorded tape on an ordinary DV device.

* Set this for both playback and recording.

* This is unrelated to the audio level via the IEEE1394 signal.

Selects which channel audio to output when playing back a DV tape with the audio signal recorded in 4 channels.

(Can only be set in VTR mode)

CH1/2

: Outputs the CH-1 and CH-2 channel audio.

INPUT1 MIC REF.*

INPUT2 MIC REF.*

AUDIO MODE*

Sets the reference audio input level for the INPUT1 connector. (When the [AUDIO INPUT] switch 3 on page 16 is

set to MIC or MIC+48)

This device records the audio in CH-1 and CH-2 while shooting.

: Outputs all 4 channels of audio at the same time.

: Outputs the CH-3 and CH-4 channel audio.

MIX

CH3/4

–50dB

–60dB

: Sets the reference audio input level at –50 dB.

: Sets the reference audio input level at –60 dB.

MEMO

Sets the reference audio input level for the INPUT2 connector. (When the [AUDIO INPUT] switch 3 on page 16 is

set to MIC or MIC+48)

This device does not have a function for dubbing to the CH-3 and CH-4 channels.

–50dB

–60dB

: Sets the reference audio input level at –50 dB.

: Sets the reference audio input level at –60 dB.

PAGE BACK

When the cursor is in this position, press the SHUTTER dial to the AUDIO/MIC[1/2] menu screen.

Selects the audio sampling frequency for recording. (Both CH-1 and CH-2)

(When HDV format is set, this is fixed at 48K and “[48K]” is displayed.)

32K

48K

: Digitally records with a 12-bit, 32 kHz sampling frequency.

: Digitally records with a 16-bit, 48 kHz sampling frequency.

* If the DV format is 12-bit, 32 kHz, up to 4 recording track channels are available.

Of those, this device records on the CH-1 and CH-2 channels. This device is not capable of dubbing.

AUDIO LIMITER*

Sets whether or not AUDIO LIMITER functions when the [CH-1/CH-2 AUDIO SELECT] switch 2 on page 13 is set

to MANU.

OFF

: AUDIO LIMITER is turned off.

: AUDIO LIMITER is turned on. Recording level is suppressed when excessive audio is input.

PAGE BACK

To display the AUDIO/MIC[2/2] menu screen, move the cursor to this position and press the SHUTTER dial.

When the cursor is in this position, press the SHUTTER dial to return to the TOP MENU screen.

MENU SCREENS

LCD/VF[1/4] Menu Screen

LCD/VF[2/4] Menu Screen

The LCD/VF menu screen consists of four screens. (1/4 screen, 2/4 screen, 3/4 screen, 4/4 screen)

The LCD/VF[1/4] menu screen can only be set in camera mode.

In VTR mode, this screen consists of two screens. (1/2 screen, 2/2 screen)

The LCD/VF[2/4] menu screen can only be set in camera mode.

Item

Function/Setting (bold characters indicate initial settings)

Sets the image display method when the LCD monitor is in counterview position.

LCD MIRROR MODE

Item

Function/Setting (bold characters indicate initial settings)

NORMAL

MIRROR

: Image is displayed without inverting.

: Inverted image is displayed.

ZEBRA

Switches the luminance level of the subject sections where the zebra pattern is displayed.

• NORMAL/MIRROR is set when the SHUTTER dial is pressed.

60-70%

70-80%

85-95%

OVER95%

OVER100%

: Zebra pattern is displayed in sections with luminance levels between 60% and 70%.

: Zebra pattern is displayed in sections with luminance levels between 70% and 80%.

: Zebra pattern is displayed in sections with luminance levels between 85% and 95%.

: Zebra pattern is displayed in sections with luminance levels over 95%.

MEMO

MIRROR setting is disabled when color bar is displayed or status is in magnified size.

X See “Outputting Color Bars” on page 101.

X See “Magnified Status Indications on the LCD Monitor” on page 29.

: Zebra pattern is displayed in sections with luminance levels over 100%.

F. NO/IRIS IND.

FILTER

Selects whether or not the F-number of the lens iris/iris level mark is displayed in the status display on the LCD mon-

itor or in the viewfinder. (STATUS 1 screen)

PAGE BACK

When you display the LCD/VF[3/4] menu screen, move the cursor to this position and press the SHUTTER dial.

When the cursor is in this position, press the SHUTTER dial to return to the LCD/VF[1/4] menu screen.

OFF

F.NO

: F-number and iris level mark is not displayed.

: F-number is displayed.

F.NO+IND.

: F-number and iris level mark is displayed.

Selects whether or not the FILTER position of this device is displayed in the status display on the LCD monitor or in

the viewfinder. (STATUS 1 screen)

OFF

: FILTER position is not displayed.

: FILTER position is displayed.

Selects whether or not the safety zone is shown on the LCD monitor or in the viewfinder together with the form of

the safety zone indication.

SAFETY ZONE

OFF

: Not displayed.

4:3

: 4:3 zone is displayed.

14:9

: 14:9 zone is displayed.

16:9

: 16:9 zone is displayed.

16:9+4:3

2.35:1 CE

: 16:9 zone and 4:3 zone are display mixed. (This cannot be selected when DV format is set.)

: Displays 2.35:1 zone in the middle of the screen.

(Only in HDV format or 24P or 25P mode)

: Displays 2.35:1 zone at the top of the screen.

(Only in HDV format or 24P or 25P mode)

2.35:1 CH

CENTER MARK

Sets whether or not a center mark is displayed when the safety zone is displayed.

: Center mark is displayed.

OFF

: Center mark is not displayed.

MEMO

When the SAFETY ZONE item is set to OFF, “- - -” is indicated and this item cannot be selected.

FOCUS ASSIST

Sets the FOCUS ASSIST function. Press the [FOCUS ASSIST] button on page 14 (6) or page 18 (7) to operate

the FOCUS ASSIST function.

NORMAL

: Only the [FOCUS ASSIST] function operates.

(The focus area becomes blue, red or green, making it easier to focus.)

: The FOCUS ASSIST function and ACCU-FOCUS (forced focus) function operates.

This makes the depth of field shallower, making it easier to focus. ACCU FOCUS automatically

turns OFF after approximately 10 seconds.

ACCU-FOCUS

COLOR

LEVEL

Sets the display color for focusing when running the FOCUS ASSIST function.

BLUE

RED

GREEN

: Displays the area of focus in blue.

: Displays the area of focus in red.

: Displays the area of focus in green.

Sets the display range of the focal area when the FOCUS ASSIST function is in use.

LOW

MIDDLE

HIGH

: Displays the focal area narrower than MIDDLE.

: Displays the focal area in normal setting.

: Displays the focal area wider than MIDDLE.

PAGE BACK

When you display the LCD/VF[2/4] menu screen, move the cursor to this position and press the SHUTTER dial.

When the cursor is in this position, press the SHUTTER dial to return to the TOP MENU screen.

SAFETY ZONE and CENTER MARK will not be displayed when this device is in VTR mode (PLAY, STL, FWD, REV).

MENU SCREENS

LCD/VF[3/4] Menu Screen

LCD/VF[4/4] Menu Screen

[1/2] screen is displayed in the VTR mode.

[2/2] screen is displayed in the VTR mode.

Item

Function/Setting (bold characters indicate initial settings)

This is not displayed in VTR mode.

VIDEO FORMAT

Selects whether to display the video format in the status display on the LCD monitor or the viewfinder.

(Camera mode: STATUS 1 screen, VTR mode: STATUS screen)

: Displays the video format.

: Does not display the video format.

In camera mode : Displays the video format set in the REC item on the VIDEO FORMAT menu screen.

Item

Function/Setting (bold characters indicate initial settings)

Selects the LCD monitor and viewfinder display switching method.

OFF

LCD+VF

OFF

: Viewfinder always displayed the image.

: Turns off the viewfinder display when the LCD monitor is opened.

In VTR mode

: Displays the video format recorded on the playback tape or the video format input from the

IEEE1394 connector.

MEMO

When this item is set to ON, the contents displayed on the LCD monitor can be changed with the DISPLAY button.

X See page 29.

TAPE REMAIN

Selects whether or not the remaining tape time (minutes) is shown in the status display on the LCD monitor or in the

viewfinder.

(Camera mode: STATUS 1 screen, VTR mode: STATUS screen)

LCD CONTRAST

VF CONTRAST

BLACK & WHITE*

Adjusts the contrast of the LCD.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

: Displayed.

OFF

: Not displayed.

Adjusts the contrast of the viewfinder.

[Settings: MIN (–5), –4 - NORMAL (0) - 4, MAX (5)]

TC/UB

Selects whether or not the time code or user’s bits data should be shown in the status display on the LCD monitor

or in the viewfinder.

(Camera mode: STATUS 1 screen, VTR mode: STATUS screen)

Selects the LCD monitor and viewfinder display style.

COLOR

: Displays the image in color.

: Displayed.

B&W

: Displays the image in black and white.

OFF

: Not displayed.

* Whether the time code or user’s bits data is shown is selected with the TC DISPLAY switch.

MEMO

AUDIO

Selects whether the audio level meters should be shown in the status display on the LCD monitor and the viewfinder

Characters are always displayed in color.

screen.

(Camera mode: STATUS 1 screen, VTR mode: STATUS screen)

PAGE BACK

Camera mode:

OFF

: Displayed.

: Not displayed.

When the cursor is in this position, press the SHUTTER dial to return to the LCD/VF[3/4] menu screen.

VTR mode:

When the cursor is in this position, press the SHUTTER dial to return to the LCD/VF[1/2] menu screen.

BATTERY INFO.

For setting the status display method when loading the Anton-Bauer Battery.

The status will be displayed on the LCD screen and the viewfinder screen.

(In camera mode, only displayed when in STATUS 1 screen.)

VOLTAGE

CAPA%

TIME

: Indicates battery voltage in 0.1 V steps [V]

: Remaining battery is shown in percentage [%]

: Remaining battery is shown in minutes [min]

• VOLTAGE and CAPA% can be selected when using an IDX Endura battery. When TIME is set, VOLTAGE is dis-

played.

MEMO

• When TIME or CAPA% is selected, the battery indicator displayed before the value changes depending on the

remaining battery level.

}: 12% or less |: 12% to less than 50% {: 50% or more

• When remaining battery level becomes less than 12%, the display changes to “} RES”.

• When CALIBRATION is required from the battery, the display switches between TIME (CAPA%) display (30 sec-

onds) and “} CAL” display (2 seconds) repeatedly.

• For CALIBRATION, refer to the instruction manual of Anton-Bauer Battery.

• Please use the remaining battery level and remaining time as a reference for shooting duration.

SHUTTER DISP.

Sets the shutter display method to seconds or angle.

SEC

DEG

: Seconds

: Degrees

MEMO

This item is available when REC on the VIDEO FORMAT[1/2] menu screen is set to HDV-HD24P, DV-24P, DV-

24PA, HDV-HD25P, or DV-25P.

Shutter display method is fixed to SEC for other settings. (“[SEC]” is displayed)

PAGE BACK

Camera mode:

To display the LCD/VF[4/4] menu screen, move the cursor to this position and press the SHUTTER dial.

VTR mode:

To display the LCD/VF[2/2] menu screen, move the cursor to this position and press the SHUTTER dial.

Camera mode:

When the cursor is in this position, press the SHUTTER dial to return to the LCD/VF[2/4] menu screen.

VTR mode:

When the cursor is in this position, press the SHUTTER dial to return to the TOP MENU screen.

MENU SCREENS

TC/UB/CLOCK Menu

Screen

HEADER REC Menu

Screen

Time codes (TC) and user’s bits (UB) can be set on this screen. Date and time is set on the TIME/DATE screen that can be

reached from this screen.

The HEADER REC menu screen is used for settings related to the HEADER REC function. X See page 59.

Item

START KEY

Function/Setting (bold characters indicate initial settings)

Item

TC PRESET

Function/Setting (bold characters indicate initial settings)

Sets whether the HEADER REC operation should be executed when the REC/VTR trigger button is pressed while

the STOP button is pressed.

To preset the time code, align the cursor with this position and then press the SHUTTER dial.

DISABLE

STOP+REC

: HEADER REC operation is not executed.

: HEADER REC operation is executed.

EXECUTE

CANCEL

: The set time code is confirmed.

: The set time code is cancelled.

ZERO PRESET : Resets all time codes to “0”.

TC DATA

Sets the time code value for the point when the Record-Standby mode is engaged following completion of HEADER

REC.

UB PRESET

To preset the user’s bit data, align the cursor with this position and then press the SHUTTER dial.

EXECUTE

ZERO PRESET : Resets all time codes to “0”.

CANCEL : Clears the set time code.

: Confirms the set time code.

EXECUTE

CANCEL

: The set user’s bit data are confirmed.

: The set user’s bit data are cancelled.

ZERO PRESET : Resets all user’s bits data to “0”.

The frame mode is set depending on the setting in the DROP FRAME item on the TC/UB/CLOCK menu screen.

* The time code value at the point when the Record-Standby mode is engaged may differ some frames from the val-

ue set for this item.

MEMO

When the “UB REC” item is set to “OFF”, “--------” is displayed and this cannot be selected.

UB DATA

Sets the user’s bits of the HEADER REC section.

Selects whether the time code generator framing mode is drop-frame or non-drop-frame.

DROP FRAME

EXECUTE

: Confirms the set user’s bits.

DROP

: Internal time code generator works in drop-frame mode. Set this when the recorded time is im-

ZERO PRESET : Resets all user’s bits data to “0”.

portant.

CANCEL

: Clears the set user’s bits.

NON DROP

: Internal time code generator works in non-drop-frame mode. Set this when the number of frames

is important.

MEMO

• The user’s bits for the normal recording section are set on the TC/UB/CLOCK menu screen.

• When the “UB REC” item is set to “OFF”, “--------” is displayed and this cannot be selected.

To select whether or not user’s bit data should be recorded.

To select whether the user’s bits should be displayed during playback of a tape with recorded user’s bits data.

UB REC

: User’s bits are recorded during recording.

User’s bits are displayed during playback.

: User’s bits are not recorded during recording.

User’s bits are not displayed during playback.

BARS TIME

Sets the duration (seconds) in which the color bar signal and test tone (1 kHz) is recorded during HEADER REC. (1-

sec steps)

[Settings: 0SEC - 30SEC - 99SEC]

OFF

BLACK TIME

PAGE BACK

Sets the duration (seconds) in which the black signal is recorded during HEADER REC. (1-sec steps)

[Settings: 0SEC - 30SEC - 99SEC]

TC DUPLI.

Sets how to record the time code (TC) and user’s bits (UB) during IEEE1394 input of HDV/DV format.

OFF

: Records the TC/UB set in this device.

: Records the TC/UB of the IEEE1394 input.

The TC/UB/CLOCK menu screen returns when the SHUTTER dial is pressed.

MEMO

In HDV format, the UB set in this device is recorded regardless of the setting.

HEADER REC..

To make settings related to the HEADER REC function, align the cursor with this position, and then press the SHUT-

TER dial.

X See “HEADER REC Menu Screen” on page 91.

TIME/DATE..

PAGE BACK

To make settings related to the date and time, align the cursor with this position and then press the SHUTTER dial.

X See “TIME/DATE Menu Screen” on page 92.

When the cursor is in this position, press the SHUTTER dial to return to the TOP MENU screen.

This can be displayed and selected when 60/30 is set for the FRAME RATE item on the VIDEO FORMAT menu screen.

(When 24 is set, this is fixed at “NON DROP” and “[NON DROP]” is displayed.)

This can be displayed and selected when 50/25 is set for the FRAME RATE item on the VIDEO FORMAT menu screen.

MENU SCREENS

TIME/DATE Menu Screen

OTHERS[1/2] Menu Screen

The OTHERS menu screen consists of two screens (1/2 screen, 2/2 screen)

Item

Function/Setting (bold characters indicate initial settings)

Sets whether the date and time are shown in the status display on the LCD monitor or in the viewfinder.

Item

Function/Setting (bold characters indicate initial settings)

DISPLAY

OFF

: Not displayed.

: Displayed.

ANALOG OUT CHAR.

Sets whether or not to display characters such as status and menus on the screen for the [Y/PB/PR] and [VIDEO

OUT] terminals.

When a tape with time and date not recorded is played back, there will be no display of time and date even when

this item is set to ON.

OFF

: On-screen display.

: No on-screen display.

DISPLAY MODE

In the Camera mode, the date and time are displayed in accordance with the following settings.

The date and time recorded on a tape are displayed in accordance with the following settings.

MEMO

When ANALOG OUT CHAR. item is set to ON, the content displayed on the viewfinder is also displayed in the

video from the video output terminal. During VTR recording, the mode is displayed in red on the viewfinder. How-

ever, color is not applied for the following video outputs.

• Component output of recording or playback in DV format

• Composite output

BARS+CAM

BARS

CAM

: Date and time are always displayed.

: Date and time are displayed when the color bars are output.

: Date and time are displayed when the camera images are output.

When the DISPLAY item is set to OFF, “- - -” is indicated and this item cannot be selected.

DISPLAY STYLE

DATE STYLE

Selects the style for the date and time display.

DATE+TIME

DATE

TIME

: Date and time are displayed.

: Date only is displayed.

: Time only is displayed.

LONG PAUSE TIME

Selects the time (minutes) before the tape protect mode (drum head rotation stopped) is engaged when the record-

standby condition continues.

3MIN

5MIN

: 3 minutes

: 5 minutes

When the DISPLAY item is set to OFF, “- - -” is indicated and this item cannot be selected.

* When used in a cold environment or when the stopped or STILL status continues, the setting will be 3 minutes or

less regardless of the setting on the menu.

* Normally, set “3MIN” and use this to prevent head clogging and tape damage.

Selects the style for the date display.

YY/MM/DD

MM/DD/YY

DD/MM/YY

: Displayed in the format of year/month/date.

: Displayed in the format of month/date/year.

: Displayed in the format of date/month/year.

ALARM VR LEVEL

Selects whether or not alarm sound is emitted and the volume of the alarm sound.

The alarm sound is output through the monitoring loudspeaker and the PHONES jack.

Variation Range: U model: MM/DD/YY E model: DD/MM/YY

When the DISPLAY item is set to OFF, “- - -” is indicated and this item cannot be selected.

OFF

LOW

: Sound is not output.

: Alarm sound is soft.

TIME STYLE

Selects the style for the time display.

MIDDLE : Alarm sound is normal.

HIGH : Alarm sound is loud.

Selects the lighting method of the FRONT TALLY lamp during recording.

24 HOUR

12 HOUR

: Displays the time using the 24-hour system.

: Displays the time using the 12-hour system.

When the DISPLAY item is set to OFF, “- - -” is indicated and this item cannot be selected.

FRONT TALLY

BACK TALLY

FORMAT LED

BLINK

: The lamp blinks from when the REC/VTR trigger is pressed and until recording starts. The lamp lights

SEC DISPLAY

Selects whether to display the seconds in the time display.

OFF

steadily during recording.

: Seconds are displayed.

: Seconds are not displayed.

OFF

: The lamp lights only during recording.

: The lamp is always off.

When the DISPLAY item is set to OFF, “- - -” is indicated and this item cannot be selected.

Selects the lighting method of the BACK TALLY lamp during recording.

TIME SHIFT

Sets the clock OFFSET time. (1H steps)

Adds time to the built-in clock (time compensation) and displays it. The adjusted time is also recorded on the tape.

[Settings: –23H - –1H, OFF, +1H - +23H]

BLINK

: The lamp blinks from when the REC/VTR trigger is pressed and until recording starts. The lamp lights

steadily during recording.

OFF

: The lamp lights only during recording.

: The lamp is always off.

CLOCK ADJUST

PAGE BACK

To adjust the date and time, align the cursor with this position and then press the SHUTTER dial.

The date and time are set on the CLOCK ADJUST screen.

X See “Setting the Date and Time” on page 42.

Sets whether or not the [HDV/DV LED] g on page 15 lights for HDV format or DV format.

: Lights.

The TC/UB/CLOCK menu returns when the SHUTTER dial is pressed while the cursor is at this position.

OFF

: Does not light.

PAGE BACK

To display the OTHERS[2/2] menu screen, move the cursor to this position and press the SHUTTER dial.

The TOP MENU screen returns when the SHUTTER dial is pressed while the cursor is at this position.

MENU SCREENS

OTHERS[2/2] Menu Screen

This is not displayed in VTR mode.

Item

Function/Setting (bold characters indicate initial settings)

Item

Function/Setting (bold characters indicate initial settings)

1394 REC TRIGGER*

Sets how to control the REC trigger command output from the IEEE1394 connector. (Can be displayed and set in

camera mode)

DR-HD100 A.OFF*

Selects whether or not to turn OFF the DR-HD100 (HDD unit by FOCUS enhancements) when this device is turned

OFF.

Set this when recording a backup of the HDV/DV signal from this device onto another device.

OFF

: Power does not turn OFF.

OFF

: Does not control the backup device.

: Power turns OFF with this device.

SYNCRO : Controls the backup device in conjunction with the recording start/stop mode status on this device, and

if there is no videocassette or if no tape remains for recording, controls the backup device in conjunction

with the REC trigger button and the lens VTR button on this device.

MEMO

• The [ mark is displayed at the upper right of the LCD monitor and viewfinder when the DR-HD100 is con-

nected. If this device is turned OFF before the mark is displayed, power does not turn OFF even if this setting is

ON.

• This setting is canceled and the DR-HD100 does not turn OFF in the following instances.

- 1394 REC TRIGGER item is set to OFF

SPLIT

: The REC trigger button on the right panel of this device controls the backup device recording start/stop.

Set this when you want to control the timing of the recording on this device and the backup device sep-

arately.

SERIES : Automatically starts recording on a backup device that is on Pause when the tape on this device has less

than 3 minutes remaining during shooting.

- VTR mode is set

• When the DR-HD100 power turns off and this device is turned ON again, after 12 seconds, “DR-HD100 power?”

appears on the LCD monitor for 7 seconds.

MEMO

• If you use the backup recording function on the BR-HD50, set this item to OFF.

• The cursor (K) does not move to this item when this device is recording.

MENU ALL RESET

Selects whether to reset the menu screen settings to initial settings.

The camera mode and VTR mode menu settings are reset. (The TC PRESET, UB PRESET, and CLOCK ADJUST

settings are not reset.)

BACK SPACE [HDV]*

This function controls the camera tape transport, back space and pre-roll time when the camera is connected to an

external HDD or external back up Recorder via IEEE1394 in HDV mode.

P-1394 : Priority for IEEE1394 recording (Auto setting)

CANCEL

: The settings are not reset.

EXECUTE : The settings are reset.

P-TAPE : Priority for camera VCR recording

MEMO

• The cursor (K) does not move to this item when the VTR is activated.

• If the current menu settings and the factory settings have different FRAME RATE settings, “REBOOT!” is dis-

played for 3 seconds, this device automatically turns off and then turns on.

1394 REC

TRIGGER

(X See page 94)

Internal

VCR

start delay

IEEE1394

connection

External Recorder or HDD

vie IEEE1394 terminal

BACK SPACE [HDV]

OFF

SYNCRO

SPLIT

N/A

PAGE BACK

DRUM HOUR

When the cursor is in this position, press the SHUTTER dial once to return to the OTHERS[1/2] menu screen.

See Note 1

See Note 2

N/A

Connected and

Power ON

approx. 3 seconds

approx. 1 second

Displays the drum usage time.

Use as an estimate for regular maintenance.

The cursor (K) does not move to this item.

SERIES

OFF

P-1394

FAN HOUR

Displays the fan motor usage time.

Use as an estimate for regular maintenance.

The cursor (K) does not move to this item.

SYNCRO

SPLIT

No connection or

Power OFF

N/A

SERIES

OFF

SYNCRO

SPLIT

See Note 3

N/A

Connected and

Power ON

SERIES

OFF

P-TAPE

SYNCRO

SPLIT

No connection or

Power OFF

N/A

SERIES

Note 1:

REC start signal will be sent 3 seconds after pressing REC trigger button.

* Actual recording start time is depending on recorder performance.

Note 2:

REC start signal will be sent just after pressing REC trigger button.

* Actual recording start time is depending on recorder performance.

Note 3:

In this mode, the IEEE1394 stream is discontinuous during internal VCR back space editing (when the REC trigger

is operated). This may result in breaks in the recording on tape on an external recorder. In the case of HDD recording

this may result in this device staying in REC PAUSE or divided files.

MEMO

The cursor (K) does not move to this item when this device is recording.

MENU SCREENS

5.Turn the SHUTTER dial, bring the cursor (K) to the

STORE item and press the SHUTTER dial.

Displaying the FILE MANAGE menu

screen

Saving settings

FILE MANAGE Menu

Screen

•

EXECUTE (if the file already exists, “OVERWRITE”)

flashes.

Select the STORE FILE.. item on the FILE MANAGE menu

screen.

Select the FILE MANAGE.. item on the TOP MENU screen.

1. Turn the SHUTTER dial, bring the cursor (K) to SELECT

You can perform the following operations in the FILE MAN-

AGE menu screen.

and press the SHUTTER dial.

•

The file name setting area flashes.

•

Settings corresponding to shooting conditions can be read

immediately with the following read-only files.

Loading a menu settings file

2. Turn the SHUTTER dial, select the file to save to, and

press the SHUTTER dial.

LIVE HD60P

LIVE HD50P

: Ideal setting for HD60P format

: Ideal setting for HD50P format

Select the LOAD FILE.. item on the FILE MANAGE menu

screen.

CINEMA HD24P : Ideal setting for movie-quality shoot-

ing

The read-only files listed above cannot be saved or

reset.

6.With EXECUTE selected, turn the SHUTTER dial to save

the menu settings to the selected file.

•

Save menu settings (Camcorder: CAM1, 2, 3, 4; SD mem-

ory card: EXT1, 2, 3, 4) to files.

•

Load saved files.

You can set a SUB NAME for the file to be saved.

Reset the menu settings to the factory settings.

Initialize (format) an SD memory card.

When you set CANCEL for the LOAD, STORE, RESET

and FORMAT SD CARD items, these operations are not

executed.

„ Setting a SUB NAME

If you do not want to set a SUB NAME, go to Step 5..

Execute

Complete

FILE MANAGE menu screen

3. Turn the SHUTTER dial, bring the cursor (K) to SUB

Error displays

NAME and press the SHUTTER dial.

•

A message is displayed in the LCD monitor or the view-

finder.

•

The first character in the file name flashes.

•

NO CARD:

No SD memory card is inserted.

Insert an SD memory card.

EXECUTE : Displayed for 3 seconds

COMPLETE : Displayed for 3 seconds

•

NO FORMAT:

ERROR

: Flashes (Error displays X See page 97.)

The SD memory card is not initialized (formatted).

Initialize (format) the SD memory card.

•

NO ACCESS:

There is a problem with the SD memory card.

Replace the SD memory card.

•

WRITE PROTECT:

The SD memory card may be write-protected.

Check that write-protection is disabled.

1.Turn the SHUTTER dial, bring the cursor (K) to SELECT

Execute

Complete

and press the SHUTTER dial.

•

DISK FULL:

•

The file name setting area flashes.

The SD memory card does not have enough free space.

Delete unwanted data or initialize (format) the card.

Settable Characters

2.Turn the SHUTTER dial, select the file to load and press

the SHUTTER dial.

•

INVALID VIDEO FORMAT:

Flashing

A settings file for a video format that is not supported was

called up.

3.Turn the SHUTTER dial, bring the cursor (K) to the

Error display

Space

LOAD item and press the SHUTTER dial.

Settings files for video formats that are not supported can-

not be called up.

•

EXECUTE flashes.

4. Turn the SHUTTER dial, select the character, and press

4.With EXECUTE selected, press the SHUTTER dial to

Error

the SHUTTER dial.

•

READ ONLY FILE:

read the menu settings in the selected file.

•

The second character in the file name flashes.

Indicates a read-only file.

Read-only files cannot be saved.

If the current menu settings and the menu settings to be

loaded have different video format settings, “REBOOT!”

is displayed for 3 seconds, this device turns off automati-

cally and then turns on.

Repeat Step 4. up through the eighth character.

If there is an error:

•

Press the STATUS button

screen.

Press the SHUTTER dial o Return to the FILE MAN-

AGE menu screen.

To exit the FILE MANAGE screen:

Return to the normal

•

Flashing

Error display

•

Move the cursor (K) to PAGE BACK and press the SHUT-

TER dial or press the STATUS button.

Error

Reboot display

CAUTION

This device cannot load scene files from GY-HD100/GY-

HD110-series devices.

MENU SCREENS

FEATURES OF THE CAMERA SECTION

MEMO

3.Move the cursor (K) to the SKIN COLOR DET. item,

press the SHUTTER dial and select EXECUTE to switch

to skin color detection mode.

FILE MANAGE Menu Screen

(Cont’d)

Even if CAM1, CAM2, CAM3, or CAM4 are reset, the cur-

rent settings are not reset.

To reset the currently set values, select “CURRENT”.

How to Use Skin Detail

4.Shoot so that the color area you want to detect within the

detection area frame is input.

To confirm the detection area, press the SHUTTER dial

and set SKIN COLOR DET. to STOP.

This function suppresses edge sharpening in the skin color

areas of the video signal, enabling velvety, smooth skin tones.

•

The frame on the screen is the detection area for the

skin detail function.

Initializing (formatting) an SD mem-

ory card

Resetting the menu settings to the

factory settings

The color within the detection area is recognized as

the color that the skin detail function will use.

If the color within the detection area is not recognized

as the color that the skin detail function will use,

“ERROR” is displayed on the screen.

Setting the skin detail function color and range

Before initializing (formatting) a card:

SHUTTER dial

Select the RESET FILE.. item on the FILE MANAGE menu

screen.

1Insert and remove the SD memory card with the power

to this device OFF.

2Disable write-protection on the SD memory card.

USER

SHUTTER

3Check that an SD memory card has been inserted into

ND FILTER

this device.

1.Turn the SHUTTER dial, bring the cursor (K) to the FOR-

Detection

area

MAT SD CARD item and press the SHUTTER dial.

•

CANCEL flashes.

STATUS

2.Turn the SHUTTER dial, and when EXECUTE flashes,

press the SHUTTER dial to initialize (format) the card.

SKIN COLOR ADJUST menu screen

STATUS button

1. Turn the SHUTTER dial, bring the cursor (K) to SELECT

and press the SHUTTER dial.

•

The file name setting area for the file to be reset

flashes.

1. Display the ADVANCED PROCESS menu screen.

Black and

white

presenta-

tion

In menu setting procedure

2. Turn the SHUTTER dial, select the name of the file to

TOP MENU screen

CAMERA PROCESS[1/2]

Execute

Complete

reset, and press the SHUTTER dial.

CAMERA PROCESS[2/2] o Select ADVANCED PRO-

CESS item.

Color

presenta-

tion

CAM1, CAM2, CAM3, CAM4, CURRENT (current set-

tings)

3. Turn the SHUTTER dial, bring the cursor (K) to the

Flashing

RESET item and press the SHUTTER dial.

Error display

•

EXECUTE flashes.

SKIN COLOR ADJUST screen

4. With EXECUTE selected, press the SHUTTER dial to

reset the settings.

Error

5.If you want to change the range of colors recognized with

Cursor

the skin color detection function, follow the steps below.

1Turn the SHUTTER dial, bring the cursor (K) to the

SKIN COLOR RANGE item and press the SHUTTER

dial.

If there is an error:

Check items 2 and 3 in “Before initializing (formatting) a

card”.

CAMERA PROCESS[2/2] menu screen

o The setting area flashes and can be changed.

2Turn the SHUTTER dial up or down to widen or narrow

the color range.

Execute

Complete

2. Turn the SHUTTER dial, bring the cursor (K) to the SKIN

COLOR ADJUST item and press the SHUTTER dial.

•

Set the range as you check the color display.

3To confirm the color range, press the SHUTTER dial.

The setting returns to its lit state.

•

The SKIN COLOR ADJUST screen is displayed.

The entire screen becomes black and white, and only

the areas recognized by the skin detail function are

displayed in color.

If the current menu settings and the factory settings have

different video format settings, “REBOOT!” is displayed

for 3 seconds, this device turns off automatically and then

turns on.

•

6.To stop the SKIN COLOR ADJUST function, turn the

SHUTTER dial, bring the cursor (K) to the PAGE BACK

item and press the SHUTTER dial.

MEMO

In the SKIN COLOR ADJUST menu screen, the lens image

is not inverted and flipped even if the REVERSE PICTURE

item in the CAMERA PROCESS[2/2] menu screen is set to

ROTATE.

Reboot display

When this happens, the SUB NAME initial value,

“[SCENE]” is displayed.

ADVANCED PROCESS menu screen

FEATURES OF THE CAMERA SECTION

How to Use Skin Detail

(Cont’d)

Outputting Color Bars

This device can output three types of color bars, depending

on the camera settings.

Using the Skin Detail Function

To use the skin detail function set on the SKIN COLOR

ADJUST screen, select “ON” for the SKIN DETECT item on

the CAMERA PROCESS[1/2] menu screen.

In addition, you can use the LEVEL item to set three levels of

suppression of skin color area detail enhancement in the

video signal. X See page 78.

NTSC standard : Outputs color bars compliant with the

SMPTE standard.

PAL standard

: Outputs color bars compliant with the

EBU standard.

16:9 screen

: Outputs multi-format color bars.

While the skin detail function operates, the “SD” indicator is

displayed on the STATUS 0 and STATUS 1 screen in the

viewfinder or LCD monitor.

To output color bars, make the following settings.

1. Turn the FULL AUTO switch to “OFF”.

2. Set the BARS item on the CAMERA OPERATION menu

screen to “ON”. X See page 77.

•

Color bars are output.

FULL AUTO switch

“SD” display

STATUS 0

Confirming the color tone area adjusted

with the Skin Detail function

When you push the ZEBRA switch on the front panel to

“SKIN AREA”, the skin detail function turns ON, and the color

area adjusted with the skin detail function is displayed in

color in the LCD monitor or viewfinder.

USER button

„ Outputting color bars using the USER buttons

1. Turn the FULL AUTO switch to “OFF”.

2. Assign “BARS” to one of the USER1, 2 or 3 buttons.

X See “SWITCH MODE Menu Screen” on page 83.

3. Press the USER button to which “BARS” was assigned.

•

Color bars are output.

MEMO

•

You can select whether to output an audio test signal

during color bar output using the TEST TONE item on

the AUDIO/MIC[1/2] menu screen. X See page 84.

Color bars are not output when FULL AUTO mode is ON

or in VTR mode.

ZEBRA switch

•

MEMO

•

When the REVERSE PICTURE item in the CAMERA

PROCESS[2/2] menu screen is set to ROTATE, skin

detail function is available but the detection area is not

displayed in the viewfinder or LCD screen.

•

When COLOR GAIN item on the ADVANCED PRO-

CESS menu screen is set to “OFF”, only the portion the

skin detail function is working is displayed in skin color.

X See page 80.

100

101

OTHERS

Display

Status

Action

Warnings and Responses

CHANGE PB TAPE

FORMAT*

Image format which is different from the one set in the PB Check the setting for the PB TAPE item.

TAPE item on the VIDEO FORMAT[2/2] menu screen is be- X See page 76.

ing played back.

LOW VOLTAGE*

Battery is low.

Charge the battery pack or replace it.

TAPE NEAR END*

There are less than 3 minutes remaining on the tape (flash- To continue shooting, find a new tape or replace the tape.

es only when recording).

Warnings are displayed on the LCD monitor or the viewfinder if there was a mistaken operation, if the battery or tape is low, or if

there is a problem on the VTR.

In addition, if the tape or battery is low or the VTR has a problem, the tally lamp flashes (or lights) and an alarm is output from the

monitor speaker or PHONES jack.

TAPE END*

Displayed when the tape ends.

Replace the tape.

CHANGE 1394

SWITCH*

Recording or playback video format and the IEEE1394 set- Set the IEEE1394 switch correctly, turn the power off and

ting is different when connected to the IEEE1394 port.

Tried to use the FF or REW button in camera mode.

then on again.

SWITCH TO VTR

MODE*

Press the CAM/VTR button to set VTR mode.

MEMO

This device uses microcomputers. It may not operate properly if there is external static or interference. If this happens, turn the

power off and then on again.

HEAD CLEANING

REQUIRED

Displayed when the video head is dirty. (Head clogging was Clean with a special head cleaning tape.

detected during an edit search in shooting mode as well as X See page 7.

during playback and displayed.)

Display

Status

Action

CLEANING TAPE!

COPY GUARD!*

Displayed when a head cleaning tape is inserted.

The display disappears when the head cleaning tape is re-

moved.

60/30 INHIBIT

CHANGE FRAME

RATE MENU

The FRAME RATE item is set to 50/25 or 24, and a tape re- Sets the FRAME RATE item on the VIDEO FORMAT menu

corded in 60/30 frame is played back or it is input into the screen to match the frames.

IEEE1394 port in VTR mode.

Tried to play back a copyguarded tape.

Cannot play back a copyguarded tape.

Please contact your local dealer or JVC.

Lightly push the top center of the videocassette cover.

X See page 74.

FAN MOTOR HOUR Over the prescribed fan motor usage time.

50/25 INHIBIT

CHANGE FRAME

RATE MENU

The FRAME RATE item is set to 60/30 or 24, and a tape re-

corded in 50/25 frame or it is input into the IEEE1394 port

in VTR mode.

PUSH CASSETTE

COVER*

The videocassette cover is not firmly shut.

CHANGE THE SYS- Displayed when you attempt to change FRAME RATE item When the FRAME RATE item setting is changed, the frame

24 INHIBIT CHANGE The FRAME RATE item is set to 50/25 or 60/30, and a tape

FRAME RATE MENU recorded in 24 frame is played back or it is input into the

IEEE1394 port in VTR mode.

TEM*

in the VIDEO FORMAT menu screen.

rate system for this device is changed. Check the frame

rate to use before changing the setting.

X See pages 53 and 74.

DV-60I INVALID!

DV-24P INVALID!

DV-24PA INVALID!

A tape recorded in DV-60I, DV-24P, or DV-24PA format The E model cannot play back tapes recorded in DV-60I,

was played back or input into the IEEE1394 connector in DV-24P or DV-24PA format or input into the IEEE1394 con-

When status indications are magnified, warnings are not displayed on the LCD monitor.

X See “Magnified Status Indications on the LCD Monitor” on page 29.

VTR mode on the E model.

nector in VTR mode.

DV-50I INVALID!

DV-25P INVALID!

A tape recorded in DV-50I or DV-25P format was played The U model cannot play back tapes recorded in DV-50I or

back or input into the IEEE1394 connector in VTR mode on DV-25P format or input into the IEEE1394 connector in

the U model.

VTR mode.

HDV-SD60P

INVALID!

A tape recorded in HDV-SD60P format was played back or This device cannot play back or input an HDV-SD60P/

input into IEEE1394 connector in VTR mode.

HDV-SD50P signal.

HDV-SD50P

INVALID!

A tape recorded in HDV-SD50P format was played back or

input into IEEE1394 connector in VTR mode.

INVALID TAPE!

LP TAPE INVALID!*

NO DV SIGNAL*

NO HDV SIGNAL*

COPY INHIBIT*

REC INHIBIT*

A computer data tape or a DVC PRO cassette was used. Use a MiniDV videocassette.

Tried to play back a tape recorded in LP mode.

DV signal was not input.

This device cannot record or play back in LP mode.

Set the IEEE1394 switch to DV and input a DV signal.

Set the IEEE1394 switch to HDV and input an HDV signal.

Cannot record a copyguarded signal.

HDV signal was not input.

Tried to record a copyguarded signal.

A tape that cannot be recorded (back switch is set to SAVE) Set the switch on the back of the cassette tape to REC.

was inserted.

NO TAPE*

No videocassette tape is inserted.

Insert a cassette tape.

102

103

OTHERS

„ TALLY lamp

Warnings and Responses (Cont’d)

Blinks when remaining battery power or tape is low. (Only

in Camera mode)

Blinking Pattern

Remaining Battery/Tape

Slow blinking

(once per sec.)

• Remaining battery power is low.

• Remaining tape time is equivalent to less

than 3 minutes.

Error code

Fast blinking

• Tape has run out.

(four times per sec.)

• Irregularity has occurred in the VTR.

„ Alarm Sound

When remaining battery power becomes low, a warning

sound is output from the monitoring loudspeaker and the

PHONES jack.

Warning

(In Camera mode only)

When an irregularity occurs in the VTR, a warning sound

is also output.

Whether or not alarm sound should be output and the vol-

ume level are selected with the ALARM VR LEVEL item

on the OTHERS[1/2] menu screen.

•

Warning Indications for VTR Abnormalities

Should malfunctions occur during VTR operation, this

device self-diagnoses the cause and shows the diagnose

together with an error code on the LCD monitor or in the

viewfinder.

„ Depending on the alarm conditions, the warning indicators

on the LCD monitor/viewfinder screen, the TALLY lamp,

and alarm sounds appear as shown in the following table.

Error Code

Error Details

This device Operation

Remedy

0201

Indicates dew formation (condensa- Operation stops. All opera- Leave this device with the power ON,

CONDENSATION ON DRUM tion).

tions are rejected.

until the indication disappears.

X See page 9.

3200

Tape cannot be loaded.

Switch the power OFF and then switch

it back ON. However, the tape may be

damaged depending on the circum-

stances. Please consult the person in

charge of professional video equip-

ment at your nearest JVC-authorized

service agent.

LOADING FAILURE

3300

Tape cannot be unloaded.

UNLOADING FAILURE

4100

Irregularity with eject operation.

CASSETTE EJECT FAILURE

5605 - 5609

DEFECTIVE TAPE

Tape is cut.

Operation stops.

Press the EJECT button to take out the

cassette.

Alarm Indications on LCD Monitor/

TALLY lamp

If the tape runs out during recording,

switch the power OFF and then switch

it back ON, press the EJECT button,

and then take out the cassette.

Alarm Sound

Condition

Viewfinder Screen

VTR alarm indication

(Example)

Dew formation (condensation) or error has oc-

curred in the VTR.

5702

Tape end sensor error.

Tape beginning sensor error.

Drum rotation error.

Operation stops. All opera- Switch the power OFF and then switch

TAPE END DET. ERROR

tions are rejected.

it back ON. However, the tape may be

damaged depending on the circum-

stances. Please consult the person in

charge of professional video equip-

ment at your nearest JVC-authorized

service agent.

5802

About 3 min. before tape end

(displayed during recording).

TAPE BEGIN DET. ERROR

7001

Tape end

(displayed during recording).

DRUM MOTOR FAILURE

7101

Capstan rotation error.

Supply reel rotation error.

Take up reel rotation error.

Remaining battery power is low.

CAP MOTOR FAILURE

7202 - 7203

SUPPLY REEL FAILURE

Display symbols

: Blinking once per second.

: Sound interrupted once per second.

: Blinking four times per second.

: Continuous sound.

7302 - 7303

TAKE UP REEL FAILURE

7305

Take up reel rotation error when un-

TAKE UP REEL FAILURE

8000

Tape problem detected.

EMERGENCY TAPE!

TURN POWER OFF.

System error when power is turned on. HDV/DV LED, VTR indicator Turn off the power and let this device

TURN BACK ON LATER.

and TALLY lamp flash. Only sit for sometime before turning it back

POWER switch operation is on.

accepted.

104

105

OTHERS

Troubleshooting

How to Display the Hour

Meter

The drum and fan motor usage times are displayed in the

DRUM HOUR item and the FAN HOUR items on the OTH-

ERS[2/2] menu screen as the hour meters on this device.

Use as an estimate for regular maintenance. X See page 7.

Symptoms

Remedy

• Is power supply connected correctly?

Power cannot be switched ON.

• Is battery pack recharged?

• Was the power turned ON immediately after being turned OFF?

Wait at least 5 seconds before turning the power ON again once it has been

turned OFF.

1. Turn the POWER switch ON.

2. Press the STATUS button for at least 1 second to display

the TOP MENU screen.

Recording is not possible.

• Is the REC LOCK switch on the handle set to ON?

• Is the switch on cassette set to “REC”? If it is set to “SAVE”, set it to “REC”.

• The Camera mode has not been selected. (The VTR indicator does not light.)

While the VTR indicator lights, press the MODE switch upward to turn on the

CAM indicator.

3. Turn the SHUTTER dial, select the OTHERS.. item, and

press the SHUTTER dial.

The OTHERS[1/2] menu screen is displayed.

4. Select the NEXT PAGE item on the OTHERS[1/2] menu

Camera image does not appear on LCD monitor or in viewfind- • The Camera mode has not been selected. (The VTR indicator does not light.)

screen and press the SHUTTER dial.

er.

While the VTR indicator lights, camera image will not be output.

Press the CAM/VTR switch upward to turn on the VTR indicator.

The OTHERS[2/2] menu screen is displayed.

Image shown on LCD monitor or in viewfinder is dark or blurred. • Adjust the brightness of the LCD monitor or viewfinder screen.

OTHERS[2/2] menu screen

• Is the ND filter knob set to 2?

• Is the iris closed?

• Is the shutter speed too fast?

• Is the viewfinder cable correctly connected?

Playback does not start when the play button is pressed.

Cannot play back.

• In the Camera mode, is “STOP” indicated as the VTR operation mode indica-

tor?

When “STBY” is indicated, press the STOP button to display “STOP”.

Drum usage

hours (h)

• Is the PB TAPE item on the VIDEO FORMAT menu screen set to a setting oth-

er than AUTO?

If this menu item and the tape format do not match, the tape cannot be played

back.

Cannot input an HDV/DV signal.

Noise interferes with playback video.

Sound is not output during playback.

• Is this device in VTR mode? (Is the VTR indicator lit?)

• Is the IEEE1394 switch set correctly?

Fan motor usage hours (h)

• Video head may be clogged with dirt. Clean head with the special head clean-

ing tape. X See “Precautions for Use of Head Cleaning Tape” on page 7.

„ OTHERS[2/2] Menu Screen

DRUM HOUR item : Displays the drum usage hours.

• Is the AUDIO SELECT item on the AUDIO menu screen set to CH3/4?

To output the sound of the recording, set to CH1/2.

FAN HOUR item

: Displays the fan motor usage

hours.

Noise appears when playing back a tape recorded on another • When a tape recorded on another unit is played back or used for recording,

unit.

this phenomenon may occur due to tracking errors.

5. To return to the normal screen display, do one of the fol-

The transient section between scenes recorded on other units

and those recorded on this device may appear disturbed.

lowing:

•

Press the STATUS button.

The front section’s audio level control doesn’t work.

• Is the CH-1/CH-2 AUDIO SELECT switch set to “AUTO”?

• Is the FULL AUTO switch set to “ON”?

•

Return to the TOP MENU screen, select the EXIT item

on the TOP MENU screen and press the SHUTTER

dial.

Cannot initialize (format) the SD memory card.

• Is the SD memory card write-protected? X See page 34.

Battery alarm is displayed even if a fully charged battery pack • Is the battery pack old?

is put in.

Cassette cannot be ejected after the power is turned ON.

• The capacity of the power supply may be insufficient. Check the power volt-

age.

Time code or user’s bits data not displayed.

• Is the TC/UB item on the LCD/VF[3/4] menu screen set to OFF?

If so, set to ON.

The date and time are not displayed or recorded.

• Is the DISPLAY item on the TIME/DATE menu screen set to OFF?

Set to ON when the data should be displayed and recorded.

• Is the date and time setting made? X See “Setting and Displaying the Date

and Time” on pages 41, 42.

106

107

OTHERS

[DV]

Video signal record- : DV format, 8-bit, 25 Mbps

ing format

EXTERNAL DIMENSIONS (unit: mm)

Specifications

Compression

: DV compression, 4:1:1 (NTSC)/

4:2:0 (PAL)

Audio:

[HDV]

[General]

Audio signal record- : MPEG1 Audio Layer II

ing format

[DV]

Audio signal record- : 16-bit (locked audio), 48 kHz PCM

ing format

Power requirements : DC 12 V, W 1.9 A

Power consumption : Approx. 23 W (in the Record mode)

Dimensions

: 224(W) × 242.3(H) × 401(D) mm

(U model)

224(W) × 242.3(H) × 414(D) mm

(E model)

: 3.6 d(8.0 lbs.) (U model)

3.8 d(8.4 lbs.) (E model)

(including lens (Th16 × 5.5BRMU),

viewfinder, microphone and tape)

for

channels or 12-bit, 32 kHz

PCM for 4 channels

: MiniDV tape

: 18.8 mm/sec.

: 63 minutes (with an M-

DV63PROHD tape)

Usable tape

Tape speed

Record/play time

Mass

Temperature

Operating

Storage

Humidity

Operating

Storage

[Time Code]

: 0°C to 40°C (32°F to 104°F)

: –20°C to 60°C (–4F° to 140°F)

Time code signal

: Compliance with SMPTE/EBU stan-

dard

: 30% to 80% RH

: 85% RH or less

[Connectors]

Analog composite output

: 1.0 V (p-p), 75 :, unbalanced (RCA)

Analog component output

P^B/PR

Audio inputs

Mic

[Camera section]

Image pickup device : 1/3" interline-transfer CCDs

Color separation

optical system

Number of total pixels : Approx. 1,110,000 pixels

: F1.4, 3-color separation prism

: 1.0 V (p-p), 75 :, unbalanced (BNC)

: 0.7 V (p-p), 75 :, unbalanced (BNC)

Color bars

: SMPTE/EBU type Sync system:

Internal sync (built-in SSG)

: 1/3" bayonet system

: 1/4ND, 1/16ND

: 0, 3, 6, 9, 12, 15, 18 dB, ALC

: –60 dBs, 3 k:, balanced (XLR), +48

V output for phantom power supply

: +4 dBs, 10 k:, balanced (XLR)

: –8 dBs, low impedance, unbalanced

(RCA ×2)

Lens mount

ND filter

Gain

Line

Audio outputs

Electronic shutter

Standard value

Fixed values

Earphone jack

: –17 dBs to –60 dBs, 8-: impedance

(stereo mini-jack ×2)

: 59.94 Hz (U model)/50 Hz (E model)

: 7.5

10,000 Hz, 11 steps (HDV

IEEE1394 connector : 6-pin

HD30p/HDV HD60p/DV 60i), 6.25 -

10,000 Hz, 11 steps (HDV HD25p/

HDV HD50p/DV 50i), 6 - 10,000 Hz,

12 steps (HDV HD24p/DV 24p),

6.25 - 10,000 Hz, 11 steps (DV 25p)

: 30.03 - 10,489.5 Hz (HDV HD60p/

HDV HD30p/DV 60i)

25.04 - 10,489.5 Hz (HDV HD50p/

HDV HD25p/DV 50i/DV 25p)

24.01 - 10,489.5 Hz (HDV HD24p/

DV 24p)

[ACCESSORIES]

Design and specifications are subject to change without notice.

Lens

: 1 (Excluding the CHU/CHE model)

Microphone

Core Filter

Clamp Filter

SD memory card

Instruction Manual

Warranty Card

: 1

: 4

: 1

Variable scan

(USA and Canada only)

Dynamic range

: 300% or more

For details, consult your JVC dealer.

[VTR section]

Video

Recording format

: 720/24p, 720/25p, 720/30p, 720/

50p, 720/60p (U/E model), 480/24p,

480/60i (U model), 576/25p, 576/50i

(E model)

Video Format:

[HDV]

Video signal record- : HDV720p format, 8-bit, 19.7 Mbps

ing format

Compression

: MPEG-2 video (profile

MP@H-14)

level:

108

109

INTRODUCTION

CONTROLS,

INDICATORS AND

CONNECTORS

PREPARATIONS

FOR OPERATION

SETTING AND

ADJUSTMENTS

BEFORE SHOOTING

SHOOTING

OPERATION

HD CAMERA RECORDER

PLAYBACK MODE

USING EXTERNAL

COMPONENTS

INSTRUCTIONS

GY-HD250

GY-HD251

MENU SCREENS

FEATURES OF THE

CAMERA SECTION

OTHERS

The illustration shows the GY-HD250/GY-

HD251 HD CAMERA RECORDER with the

provided lens, viewfinder and microphone

attached.

Thank you for purchasing this JVC product. Before operating this

device, please read the instructions carefully to ensure the best

possible performance.

For Customer Use:

Enter below the Serial No. which is located on the body.

Retain this information for future reference.

Model No.

Serial No.

LST0440-001A

INFORMATION (FOR CANADA)

Important Safeguards

Safety Precautions

RENSEIGNEMENT (POUR CANADA)

This Class B digital apparatus complies with Canadian ICES-

003.

Cet appareil numerique de la Class B est conforme a la norme

NMB-003 du Canada.

1. Read all of these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radia-

tors, heat resisters, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are provided for

your safety.

FOR USA AND CANADA

CAUTION

WARNING:

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF FIRE OR ELEC-

TRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This unit should be used with 12V DC only.

CAUTION:

To prevent electric shocks and fire hazards, do NOT

use any other power source.

The lightning flash with arrowhead symbol, within

an equilateral triangle is intended to alert the user

to the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of suffi-

cient magnitude to constitute a risk of electric shock

to persons.

NOTE:

The rating plate (serial number plate) is on the bottom of the unit.

CAUTION:

To prevent electric shock, do not open the cabinet. No user ser-

viceable parts inside. Refer servicing to qualified service person-

nel.

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

If the provided plug does not fit into your outlet, con-

sult an electrician for replacement of the obsolete out-

let.

AVERTISSEMENT :

10. Protect the power cord from being walked on or

pinched particularly at plug, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

POUR EVITER LES RISQUES D’INCENDIE

OU D’ELECTROCUTION, NE PAS EXPOSER

L’APPAREIL A L’HUMIDITE OU A LA PLUIE.

INFORMATION FOR USA

INFORMATION:

Ce magnétoscope ne doit être utilisé que sur du cou-

rant direct en 12V.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the

ATTENTION :

Afin d’eviter tout resque d’incendie ou d’électrocu-

tion, ne pas utillser d’autres sources d’alimentation

électrique.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will

not occur in a particular installation.

manufacturer, or sold with the appa-

ratus.

When

cart is used, use caution

when moving the cart/apparatus

combination to avoid injury tip-over.

REMARQUE:

La plaque signalétique (plaque du numéro desérie) est située sur

le cadre inférieur de l’unité.

13. Unplug this apparatus during light-

ning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug

id damaged, liquid has been spilled objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Due to design modifications, data given in this instruction book are

subject to possible change without prior notice.

The apparatus shall not be exposed to dripping or splashing and

that no objects filled with liquids, such as vases, shall be placed

close to the apparatus.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

Worded - “CAUTION - Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equivalent type.”

CAUTION:

CHANGES OR MODIFICATIONS NOT APPROVED BY JVC

COULD VOID USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC

RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CON-

DITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFER-

ENCE THAT MAY CAUSE UNDESIRED OPERATION.

WARNING:

Information for Users on Disposal of

Old Equipment

Safety Precautions (Cont’d)

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

This unit should be used with 12V DC only.

CAUTION:

FOR EUROPE

To prevent electric shocks and fire hazards, do NOT

use any other power source.

This equipment is in conformity with the provisions and protection

requirements of the corresponding European Directives.

This equipment is designed for professional video appliances and

can be used in the following environments:

NOTE:

Attention:

This symbol is only valid in the European

Union.

The rating plate (serial number plate) is on the bottom of the unit.

residential area (in houses)

commercial and light industry; e.g. offices or theatres

urban outdoors

CAUTION:

To prevent electric shock, do not open the cabinet. No user ser-

viceable parts inside. Refer servicing to qualified service person-

nel.

[European Union]

This symbol indicates that the electrical and electronic equip-

ment should not be disposed as general household waste at

its end-of-life. Instead, the product should be handed over to

the applicable collection point for the recycling of electrical

and electronic equipment for proper treatment, recovery and

recycling in accordance with your national legislation.

In order to keep the best performance and furthermore for electro-

magnetic compatibility we recommend to use cables not exceeding

the following length:

Due to design modifications, data given in this instruction book are

subject to possible change without prior notice.

Camera

The apparatus shall not be exposed to dripping or splashing and

that no objects filled with liquids, such as vases, shall be placed

close to the apparatus.

Port

Cable

Length

2 m

By disposing of this product correctly, you will help to con-

serve natural resources and will help prevent potential nega-

tive effects on the environment and human health which

could otherwise be caused by inappropriate waste handling

of this product. For more information about collection point

and recycling of this product, please contact your local

municipal office, your household waste disposal service or

the shop where you purchased the product.

DC IN

Exclusive Cable

Coaxial Cable

Shielded Cable

VIDEO

Y, PB, PR

3 m

Worded - “CAUTION - Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equivalent type.”

3 m

AUDIO INPUT1,

INPUT2

3 m

AUDIO OUT CH1,

CH2

Shielded Cable

3 m

Penalties may be applicable for incorrect disposal of this

waste, in accordance with national legislation.

Phones1, 2

Exclusive Cable

2 m

4.5 m

3 m

5 m

1 m

IEEE1394 (HDV/DV) Exclusive Cable

GENLOCK/AUX IN Coaxial Cable

(Business users)

If you wish to dispose of this product, please visit our web

page www.jvc-europe.com to obtain information about the

take-back of the product.

HD/SD-SDI

REMOTE

STUDIO

Coaxial Cable

Exclusive Cable

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accor-

dance with applicable national legislation or other rules in

your country for the treatment of old electrical and electronic

equipment.

Caution: Where there are strong electromagnetic waves or mag-

netism, for example near radio or TV transmitter, transformer,

motor, etc., the picture and the sound may be disturbed. In such

case, please keep the apparatus away from the sources of the dis-

turbance.

Dear Customer,

This apparatus is in conformance with the valid European direc-

tives and standards regarding electromagnetic compatibility and

electrical safety.

European representative of Victor Company of Japan Limited is:

JVC Technology Centre Europe GmbH

P.O. Box 10 05 52

61145 Friedberg

Germany

III

Thank you for purchasing the JVC GY-HD250U/CHU and

GY-HD251E/CHE HD CAMERA RECORDER.

These instructions are for the GY-HD250U/CHU and GY-

HD251E/CHE.

•

Time code input/output terminal and slave lock function

Slave lock to an external time code generator connected

to the time code input terminal.

The time code output terminal outputs built-in time code

generator data.

ACCESSORIES

MAIN FEATURES

•

A lens is included with the GY-HD250U and GY-HD251E.

A lens is not included with the GY-HD250CHU and GY-

HD251CHE.

•

Built-in large 3.5" color LCD display

In addition to displaying the camera image and the play-

back image, the LCD monitor shows the status screens,

menu screens for settings, and alarm indications.

•

GY-HD250/GY-HD251 records in HDV format or DV format.

DV format can record and play back SD (Standard Defini-

tion) video on Mini DV videocassettes.

HDV format can record and play back HD (High Definition)

video on Mini DV videocassettes.

There are two types of recording formats within HDV format.

HDV 720p (720 effective scan lines, progressive scan)

HDV 1080i (1080 effective scan lines, interlaced scan)

GY-HD250/GY-HD251 supports HDV 720p format. (HDV

720p)

Information applicable only to the GY-HD250U/CHU is

marked by “(U model only)”.

Information applicable only to the GY-HD251E/CHE is

marked by “(E model only)”.

Built-in monitor speaker for audio checking

The input audio can be monitored in recording or EE mode.

The playback sound can be monitored in the playback

mode. The speaker also outputs an alarm tone in case an

abnormal condition occurs in this device.

•

Recording check function for convenient recording review

function

(Excluding the CHU/CHE

model)

HDV and

are trademarks of Sony Corporation

and Victor Company of Japan, Limited.

This device is

recorder.

Videocassettes marked with the A symbol can be used.

HDV/DV video system format camera

Camera section designed with 3-CCD system for high-

quality picture

1/3" 3-CCD with 1,110,000 effective pixels employed. Dig-

ital signal processing for reproduction of HDV/DV high-

quality picture.

Lens

Microphone

•

24p mode shooting function

In HDV format, it records in 24p mode.

X See pages 10 and 33

X See page 33

It uses a 2:3:2:3 pulldown when recording to tape and con-

verts the images to 60 frames. Component output is con-

verted to 60 frames during playback as well.

24p DV format video uses a 2:3:2:3 pulldown (24p Mode).

A 2:3:3:2 pulldown (24p Advanced Mode) is also supported.

It can shoot with the same number of frames as movie

film.

The following phenomena may occur when tapes recorded

on other units (including another GY-HD250/GY-HD251)

are recorded or played back on GY-HD250/GY-HD251.

•

Multi-Zone Auto Iris Detection Circuit

Multi-zone auto iris detection circuit ensures optimum iris

position even in back light conditions or when a bright sub-

ject moves in a frame.

•

The transient section between scenes recorded on other

units and those recorded on this device may appear dis-

turbed.

Digital noise may appear during playback due to track-

ing errors.

Core Filter

Clamp Filters ×4

For DC (×2)/Audio/

IEEE1394 Cable

For Viewfinder Cable

X See page 33

•

Tapes recorded in the DVCAM format can only be played

back (simple playback).

Recording in the DVCAM format is not possible.

•

Safety Zone indication in viewfinder

X See pages 36, 64 and 67

Zebra pattern video level indication in viewfinder

This device records and plays back in the SP mode.

Recording or playback in the LP mode is not possible.

(In DV format)

Due to manufacturing dispersion of tapes, we recom-

mend not to record pictures within the first 2 to 3 min-

utes from the beginning of the tape.

Before recording important scenes, be sure to perform a

test recording and confirm that both video and audio are

recorded correctly.

Recorded video and audio contents are for private use.

Other use may infringe on the rights of copyright hold-

ers.

DVCAM is a registered trademark of Sony Corporation.

Full Auto Shooting (FAS) function

•

60 Hz/50 Hz HD or HDTV signals

Supports both 60 Hz/50 Hz HD or HDTV signals.

You can select this in a menu screen.

Eliminates the need for troublesome switch or filter opera-

tions by automatically providing a wide range of compati-

bility with shooting conditions that change as you move

between indoors and outdoors or between bright and dark

locations.

Cross-convert video output

You can output converted video from the video output con-

nectors. You can select this in a menu screen.

SD memory card

X See page 34

Tripod base

(Provided only for U model)

X See page 35

•

ND filters for 1/4ND, 1/16ND provided

IEEE1394 connector

Outputs composite, component, Y/C separate and RGB

signals as analog video in DV format. Outputs composite

and component signals in HDV format.

IEEE1394 connector (6-pin) provided. Enables transfer of

digital data to other equipment provided with IEEE1394

connector, such as a non-linear editing system. (Power

cannot be supplied.)

JVC cannot assume liabilities that may derive from the

impossibility of normal recording or playback of video or

audio due to malfunction of this device or the videocas-

sette.

•

Features HD/SD SDI output terminals

Outputs serial digital HD and SD signals.

•

1/3" bayonet type lens

Focus assist function

Enables easy and accurate focusing during shooting.

Built-in color bars (ARIB (multi-format color bars), SMPTE/

EBU type)

All product names in this manual are trademarks or regis-

tered trademarks of their respective companies.

User buttons added

Enables you to switch camera settings instantly to suit the

shooting conditions.

•

Shutter speeds and menus can be selected using a dial,

making it very easy to use.

Marks such as ™, ® and © are not used in this manual.

Variable scan shutter

There is no flicker when shooting computer screens and

other non-NTSC/PAL format screens.

•

External video signal input enabled

Records composite video signals from an external source.

GENLOCK input terminal

Input BB (Black Burst) or HD Tri-sync signals. SC phase

and HD/SD H phase adjustments can be performed.

•

Slow shutter

Makes it possible to brightly shoot video of dark subjects

with little motion by accumulating the images.

•

Time code reader/generator

The built-in time code reader/generator can be used to

record the time code and user’s bits.

Backup recording function

Continuous extended recording is possible by connecting

to HDV/DV devices.

Connect to KA-HD250 Studio Kit and use as a studio cam-

era.