Expand Your Factory Radio
add
Satellite
Radio
Harness Connection
Dip Switches
(See Manual)
Port 1
Port 2
USB
GM
Owner’s Manual
Media Gateway
ISGM11
PGHGM1
iSimple®
A Division of AAMP of America™
13190 56th Court Clearwater, FL 33760
Ph. 866-788-4237
©2009 AAMP of Florida, Inc.
09-10-09
Media Gateway & Optional Add-ons
*The Media Gateway
will only support 2
inputs.
Factory Radio
Not Included
iPod
Not Included
Media Gateway Harness
Part #: PGHGM1
Media Gateway
Part #: PXAMG
DVD Player
(not included)
Harness Connection
Dip Switches
(See Manual)
Port
1
Port
2
USB
PXAMGSR Cable
OR
MP3 Player
(not included)
1
1. Introduction
Thank you for purchasing the iSimple Electronics® Media Gateway. The Media
Gateway is designed to provide endless hours of listening pleasure from your
factory radio. To ensure that your module performs correctly with your radio, we
recommend that you read this entire manual before attempting installation of the
Media Gateway.
The Media Gateway allows connectivity for Sirius Satellite Radio (SCC1 Sold
seperately) enabling full control of this devices from the factory installed radio.
It also retains original system features such as satellite radio and rear seat
entertainment (if equipped).
2. Precautions
PREVENTING DAMAGE TO YOUR VEHICLE
Some installations require you to make wiring connections. To eliminate the risk
of an electrical short, we recommend disconnecting the vehicle’s battery prior to
installation. If you do not feel comfortable making these connections, we suggest
you seek professional installation. We recommend that the iPod be disconnected
from the interface when the vehicle is not in use.
PROPER MOUNTING LOCATION
Securely install the interface in a location free from: heat, humidity, moving parts,
sharp metal edges or direct sunlight. We recommend securing the interface to a
suitable location using; double sided tape, VelcroTM or zip-ties.
2
3. Compatibility
Your vehicle MUST either be equipped with, or have the ability to support
application information and to verify your vehicle’s compatibility.
4. Dipswitch Settings
All 4 dipswitches MUST be set in the OFF (up) position for proper operation.
ALL VEHICLES
3
5. Installation
1. When making electrical connections it is always recommended that the vehicle’s
battery be disconnected from the electrical system before performing the installation.
2. Carefully remove the trim panels covering the 7mm bolts that secure the radio into
the dash cavity. Remove these bolts, and carefully pull the radio from the dash of the
vehicle. This will provide access to the factory radio connectors where you will
connect the Media Gateway harness.
3. Disconnect the factory 16-Pin harness and 14-Pin harness from the back of the
radio. Disconnect the antenna from the radio.
4. When connecting the Satellite Radio tuner (SCC1 sold separartely), make the
folllowing connections before connecting the PXAMG to the vehicle. Plug the black
end of the 3 foot PXAMGSR (8-Pin mini-din to 8-Pin mini-din) into the second port
(closest to the dipswitches) on the Media Gateway. Connect the gray end of this cable
into the Satellite Radio tuner.
5. When connecting the auxiliary cable, plug the 8 pin mini-din into the port farthest
fromthedipswitches. Carefullyruntheauxiliarycabletothelocationwheretheauxiliary
device will be stored. If you are using the RCA input it may be necessary to run the
auxiliary device’s output cable to the PXAMG location.
6. PluginthemaleconnectorsonthePGHGM1harnessintothe16-pinportand14-pin
port on the back of the radio. Next, connect the factory 16-pin and 14-pin harness into
the female connectors on the PGHGM1 harness. Be sure to make a firm connection
but do not force it. Plug the Black micro-fit 24-pin connector on the PGHGM1 harness
into the PXAMG Media Gateway box.
8. To complete the installation secure the Media Gateway (PXAMG) and Satellite
Radio tuner (SCC1) into the cavity in the dash behind the radio. Be sure that the
cables and interface modules are not near moving parts or sharp metal edges as they
may damage the cables. To prevent rattling noises inside the dash, use zip ties, tape,
or other fasteners to mount the interfaces securely.
9. With all connections made, reconnect the vehicle’s battery, insert the key into the
ignition, and turn the vehicle on. Check for proper operation of the Media Gateway and
Satellite Radio tuner before reinstalling the factory dash panels.
10. Note: The first time you access the Gateway, your radio may display “DEV INIT”
while the device is initializing. If this is displayed, please wait one minute then cycle
the ignition off and on. Then access SAT mode again to begin normal Gateway
operation.
4
Non-Navigation Radios
6. Sirius Satellite Radio Operation
Entering Mode Select Menu
Press the “BAND” button a few times until “XM” is displayed on the screen.
Immediately turn the rotary TUNE KNOB in the top right hand corner to scroll
through available sources. Once “SIRIUS” is displayed, press the “FWD>>” butto
n
to select the displayed mode.
Channel Up
Turn the rotary TUNE KNOB clockwise to move up through the channels
Channel Down
Turn the rotary TUNE KNOB counter-clockwise to move down through the channels
Category Selection
Press the “CAT” button then press the button that corresponds with the Category you
wish to select.
Store Presets
Press and hold the preset button on which you want to store the channel.
Please Note: If you are using the Media Gateway to add Sirius but
still have factory XM installed, it is important to keep the presets in
seperate banks.
Recall Presets
Press the preset button that corresponds with the channel you want to recall.
Changing Display:
Press the “i” button to display artist and track information
Steering Wheel Controls
Press the “▲” button to cycle up through the categories.
Press the “▼” button to cycle down through the categories.
Press the “►I” button to move up through the channels.
7. Selecting AUX Input
Entering Mode Select Menu
Press the “BAND” button a few times until “XM” is displayed on the screen.
Immediately turn the rotary TUNE KNOB in the top right hand corner to scroll
through available sources. Once “AUX 1” is displayed, press the “FWD>>” butto
n
to select the displayed mode.
5
Navigation Radios
8. Sirius Satellite Radio Operation
Entering Mode Select Menu
Press the “XM” icon on the navigation screen. Immediately turn the rotary TUNE
KNOB in the top right hand corner to scroll through available sources. Once
“SIRIUS” is displayed, press the “►” icon on the screen to select the displayed
mode.
Channel Up
Turn the rotary TUNE KNOB clockwise to move up through the channels.
Channel Down
Turn the rotary TUNE KNOB counter-clockwise to move down through the channels.
Category Selection
Press the “Browse” icon then press the icon that corresponds with the Category you
wish to select.
Store Presets
Press and hold the preset button on which you want to store the channel.
Please Note: If you are using the Media Gateway to add Sirius but
still have factory XM installed, it is important to keep the presets in
seperate banks.
Recall Presets
Press the preset button that corresponds with the channel you want to recall.
Changing Display:
Press the “i” button to display artist and track information
Steering Wheel Controls
Press the “▲” button to cycle up through the categories.
Press the “▼” button to cycle down through the categories.
Press the “►I” button to move up to through the channels.
9. Selecting AUX Input
Entering Mode Select Menu
Press the “XM” icon on the navigation screen. Immediately turn the rotary TUNE
KNOB to scroll through available sources. Once “AUX 1” is displayed, press the
“►” icon on the screen to select the displayed mode..
6
10. Troubleshooting
Symptom
Cause
Remedy
The Media
The Satellite Tuner
was not properly
connected when
the PXAMG was
first connected and
initialized.
HDRT must be connected before the
PXAMG is powered on. Disconnect
the PXAMG from the vehicles harness
for 5 minutes. Verify the 8 pin DIN
HDRT cable is securely connected
at both ends before reconnecting the
vehicle harness.
Gateway does
not recognize the
Satellite Radio
Tuner (SCC1)
Radio shows “DEV Gateway device is
INIT” initializing
This only occurs the first time the
PXAMG is powered on. Wait a few
minutes, cycle ignition off and on then
enter SAT Mode.
7
11. Warranty
One Year Limited Warranty
The quality controls used in the manufacture of this product will ensure your
satisfaction. This warranty applies only to the original purchaser of this prod-
uct from an authorized iSimple® dealer. This warranty covers any supplied or
manufactured parts of this product that, upon inspection by iSimple® autho-
rized personnel, is found to have failed in normal use due to defects in mate-
rial or workmanship. This warranty does not apply to installation expenses.
Attempting to service or modify this unit, operating this unit under conditions
other than the recommended voltage will render this WARRANTY VOID.
Unless otherwise prescribed by law, iSimple® shall not be liable for any
personal injury, property damage and or any incidental or consequential
damages of any kind (including water damage) resulting from malfunc-
tions, defects, misuse, improper installation or alteration of this product. All
parts of this iSimple® product are guaranteed for a period of 1 year as follows:
Within the first 12 months from date of purchase, subject to the conditions
above, iSimple® will repair or replace the product at their discretion, if it is defec-
tive in material or workmanship providing it is returned to an Authorized iSimple®
dealer, with PROOF OF PURCHASE from an authorized iSimple® dealer.
Warning:
This equipment may be reset by unintentional electrostatic discharge during
operation. Exposure to direct sunlight or extreme heat may cause damage or
malfunction.
FCC Class B Radio Frequency
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Re-orientate or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that of which the receiver is connected.
4. Consult the dealer or an experienced radio / television technical
for help.
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
8
|