Jensen VM8022 User Manual

VM8022  
Installation and Operation Manual  
Watts Peak  
Watts en Crête  
Vatios el Máximo  
40W x 4  
160  
VM8022  
TABLE OF CONTENTS  
Introduction ..............................................................................................1  
Installation ................................................................................................1  
Wiring .......................................................................................................3  
Remote Control ........................................................................................4  
Operation .................................................................................................5  
Tuner Operation .......................................................................................7  
Disc/MP3/WMA Playback ........................................................................8  
System Setup Menu ...............................................................................10  
USB/SD Operation .................................................................................12  
Care and Maintenance ...........................................................................15  
Troubleshooting .....................................................................................16  
Specifications .........................................................................................17  
i
VM8022  
ii  
VM8022  
2. Remove Transport Screws  
INTRODUCTION  
Congratulations on your purchase of the Jensen VM8022 Mobile  
Multimedia Receiver. It’s a good idea to read all of the instructions before  
beginning the installation. We recommend having your Jensen VM8022  
installed by a reputable installation shop.  
TRANSPORT SCREWS  
INSTALLATION  
This unit is designed for installation in cars, trucks and vans with an existing  
radio opening. In many cases, a special installation kit will be required to  
mount the radio to the dashboard. These kits are available at electronics  
supply stores and car stereo specialty shops. Always check the kit  
application before purchasing to make sure the kit works with your vehicle.  
If you have trouble locating a kit or need installation assistance, contact  
Technical Support at 1-800-323-4815 from 8:30am to 7:00pm EST Monday  
through Friday and from 9:00am to 5:00pm EST on Saturday.  
Tools and Supplies  
The following tools and supplies are needed to install the radio:  
Universal Installation  
1. Check the dashboard opening size by sliding the radio into it.  
Torx type, flathead and Philips screwdrivers  
Wire cutters and strippers  
Tools to remove existing radio (screwdriver, socket wrench set or other  
tools)  
Electrical tape  
Crimping tool  
Volt meter/test light  
Crimp connections  
18 gauge wire for power connections  
16-18 gauge speaker wire  
Preparation  
1. Disconnect Battery  
If the opening is too small, carefully cut or file as necessary until the  
radio easily slides into the opening. Do not force the radio into the open-  
ing. Check for sufficient space behind the dashboard for the radio chas-  
sis.  
Before you begin, always disconnect the battery negative terminal.  
NOTE: If the VM8022 is to be installed in a car equipped with an on-  
board drive or navigation computer, do not disconnect the battery  
cable. If the cable is disconnected, the computer memory may be lost.  
Under these conditions, use extra caution during installation to avoid  
causing a short circuit.  
CAUTION: For proper operation of the DVD player, the chassis must  
be mounted within 20° of horizontal. Make sure the unit is mounted  
within this limitation.  
2. Place the radio in front of the dashboard opening so the wiring can be  
brought through. Follow the wiring diagram carefully and make certain  
all connections are secure and insulated with wire nuts or electrical  
tape. See “Wiring” on page 3. After completing the wiring connections,  
1
VM8022  
turn the unit on to confirm operation (vehicle ignition must be on). If the  
unit does not operate, re-check all wiring until the problem is corrected.  
3. Secure the rear of the unit to the car body using the mounting bolt and  
rubber cushion.  
mounting. Save all hardware and brackets as they may be used to  
mount the new radio.  
2. Carefully unsnap the plastic frame from the front of the new radio  
chassis. Remove and discard the frame.  
4. Test the radio using the “Operation” instructions that follow.  
3. Remove the factory mounting brackets and hardware from the existing  
radio and attach them to the new radio. Do not exceed M5 x 9mm  
maximum screw size. Longer screws may damage components inside  
the chassis.  
4. Wire the new radio as outlined in the Universal Installation instructions.  
5. Mount the new radio assembly to the dashboard or center console  
using the reverse procedure of step 1.  
Fuses  
When replacing a fuse, make sure the new fuse is the correct type and  
amperage. Using an incorrect fuse could damage the radio.  
RUBBER CUSHION  
MOUNTING BOLT  
RADIO  
Reconnect Battery  
When wiring is complete, reconnect the battery negative terminal.  
Technical Assistance  
If you require assistance, contact Technical Support at 1-800-323-4815  
from 8:30am to 7:00pm EST Monday through Friday and from 9:00am to  
5:00pm EST on Saturday.  
TRIM RING  
Kit Installation  
If your vehicle requires the use of an installation kit to mount this radio,  
follow the instructions included with the installation kit to attach the radio to  
the mounting plate supplied with the kit.  
1. Wire and test the radio as outlined in the Universal Installation instruc-  
tions.  
2. Install the radio/mounting plate assembly to the sub-dashboard  
according to the instructions in the installation kit.  
3. Replace the dashboard trim panel.  
ISO Installation  
This unit has threaded holes in the chassis  
side panels which may be used with the  
original factory mounting brackets of some  
vehicles to mount the radio to the  
dashboard. Please consult with your local  
car stereo shop for assistance on this type  
of installation.  
1. Remove the existing factory radio  
from the dashboard or center console  
2
VM8022  
WIRING  
Parking  
(Blue)  
(Yellow)  
(Yellow)  
Fuse (15A)  
NOTE: The amplifier in this  
radio is only designed for use with  
four speakers. Never combine  
(bridge) outputs for use with two  
speakers. Never ground negative  
speaker leads to chassis ground.  
Failure to wire exactly as shown  
may cause electrical damage to the  
radio.  
A/V Media  
Adapter Cable  
Ground  
Connect to ground terminal  
or clean, unpainted part of chassis.  
Power Antenna  
Connect to power antenna or amplifier.  
If not used, tape bare end of wire.  
Black  
Blue  
NOTE: Only connect speakers with  
a nominal impedance of 4 ohms.  
Speakers with a load  
impedance less than 4 ohms  
could damage the unit.  
Memory/Battery  
Connect to battery or 12 volt power  
source that is always live. The radio will  
not work if this wire is not connected.  
Accessory/Ignition  
Connect to existing radio wire  
or radio fuse.  
Yellow  
Red  
IMPORTANT!  
FRONT SP  
Gray  
REAR SP  
The pink parking wire MUST  
be connected to the switched  
side of the parking break  
circuit (the part that becomes  
grounded when the brake is  
applied).  
White/Black  
Stripe  
White Gray/Black  
Stripe  
Green/Black  
Stripe  
Green Purple/Black  
Stripe  
Purple  
Left Speaker  
(Front)  
Right Speaker  
(Front)  
Left Speaker  
(Rear)  
Right Speaker  
(Rear)  
3
VM8022  
REMOTE CONTROL  
The remote control will allow you to control the advanced functions of the  
VM8022.  
Operating Range  
The remote control sensor (19) is located to  
the right of the power button. The remote  
control can operate within a distance of 3~5m.  
REMOTE SENSOR  
1. ZOOM (DVD, VCD only)  
2. TITLE (DVD only)  
3. Power On/Off  
4. SETUP: Access DVD Setup  
5. Menu Navigation  
6. ENTER  
7. PROG: Enter Programmed  
Playback mode.  
8. Direct Number Entry  
9. SEL  
Replacing the Battery  
When the range of operation of the card  
remote control becomes short or stops  
functioning, replace the battery with a new  
lithium battery. Be sure to observe the proper  
polarity, as indicated below.  
(CR 2025)  
Audio Mode: Select BAS,  
TRE, BAL, FAD.  
Press and hold for System  
Menu  
10. Volume Control  
11. Mute  
12. SEEK  
2
1
Radio Tune  
Track Skip/Seek  
13. SUB.T: Subtitle (DVD only)  
14. SRC: Change Input Source  
15. REPEAT  
16. A-B Repeat  
17. Stop/Return  
18. Play/Pause  
19. GOTO Search  
20. MENU PBC  
DVD Menu  
PBC (for VCD 2.0 and up)  
21. OSD: On Screen Display  
22. AUDIO  
DVD Audio  
VCD Audio L/R/ST  
23. DISP: View On Panel Display  
24. ANGLE (DVD only)  
25. BAND/P/N  
Video System: PAL, NTSC, AUTO  
Radio Band  
4
VM8022  
OPERATION  
Power  
BALANCE: Turn the rotary encoder to adjust the balance from “R7” (full  
right) to “L7” (full left).  
FADER: Turn the rotary encoder to adjust the fader from “F7” (full front)  
to “R7” (full rear).  
Press the (power) button (2) to turn the unit on. Press and hold the power  
button again to turn the unit off.  
The unit automatically exits the audio control menu after five seconds of  
inactivity.  
NOTE: LCD panels may take longer to respond when subjected to cold  
temperatures for an extended period of time. In addition, the visibility  
of the numbers on the LCD may decrease slightly. The LCD display  
will return to normal when the temperature becomes normal.  
18  
20  
Source  
Press the SRC button (6) to select a different mode of operation, as  
indicated on the display panel. Available modes include tuner (FM1, FM2,  
FM3, AM1, AM2), DVD, SD, USB, and auxiliary (AUX).  
VM8022  
22  
LOUD  
21  
Audio Mute  
Press the MUTE button (21) to silence the audio volume. “ ” appears on  
VOL  
the display. Press MUTE again to restore volume to the previous setting.  
AS  
Volume Control  
To increase the volume, turn the rotary encoder (5) clockwise. To decrease  
the volume, turn the rotary encoder counter-clockwise. When volume is  
adjusted, the volume level will be shown on the display panel as a number  
ranging from “0” (lowest) to “63” (highest).  
SD/MMC  
/
1
6
INT  
2
5
RPT  
RDM  
3
4
Audio Menu  
Press the VOL button (5) to access the audio menu. Press the VOL button  
23  
repeatedly to move through the list of menu options.  
Menu Operation  
Press and hold the VOL button (5) for more than two seconds to access the  
menu. Press the VOL button to move through the following menu options:  
EQ MODE, BEEP, 12/24 MODE (clock), VOL MODE, A-VOL,  
SUBWOOFER, SUB VOL. The following procedures assume you have  
already accessed the menu.  
VOL  
Equalizer Selector (EQ MODE)  
The equalizer function applies preset sound effects to the unit’s audio  
output signal. Turn the rotary encoder to select from the following equalizer  
options: “OFF”, “ROCK”, “POP”, “CLASSIC” and “FLAT”. With the equalizer  
function activated, if bass or treble is adjusted, the EQ Mode will revert to  
OFF.  
BASS: Turn the rotary encoder (5) to adjust the bass level from “+7” to  
“-7”.  
TREBLE: Turn the rotary encoder to adjust the treble level from “+7” to  
“-7”.  
5
VM8022  
When the equalizer function is activated, the most recently selected bass/  
treble levels cannot be adjusted. When the equalizer function is not active,  
the unit will return to the most recently selected bass and treble levels.  
Loudness Control (LOUD)  
When listening to music at low volumes, this feature will boost the bass and  
treble ranges to compensate for the characteristics of human hearing.  
Press the LOUD button (16) to activate this feature as indicated by “LOUD”  
on the display panel. Press the LOUD button again to deactivate the  
function. “LOUD” will disappear from the display.  
BEEP  
The beep tone feature allows the selection of an audible beep tone to be  
heard each time the menu is accessed. “ON” is the default setting. Turn the  
rotary encoder to select “OFF”.  
Clock Set  
12 / 24 MODE  
1. Press the DISP button (7) to display the clock.  
2. Press and hold the DISP button until the clock blinks.  
3. Turn the rotary encoder (5) to set the minutes.  
4. Press the VOL button (5) to confirm and move to the hour field.  
5. Turn the rotary encoder to set the hour.  
This option allows selection of a 12 hour or 24 hour clock format. “24  
HOUR” is the default setting. Turn the rotary encoder (VOL control) to  
change to the 12 hour clock format.  
VOL-MODE  
6. Press the DISP button to set the clock and exit the clock set function.  
Turn the rotary encoder to select “VOL LAST” or “VOL ADJUST”.  
Reset Button  
VOL LAST: When the unit is turned on, the volume will resume at the  
level selected when last turned off.  
The RESET button (22) is located below the eject button. The reset circuitry  
protects the microprocessor circuitry. Since resetting the unit will erase the  
time and preset memories, it should only be activated upon initial  
installation after all wiring is complete, or if there is a malfunction of any of  
the switches on the unit. In these circumstances, pressing the RESET  
button will clear the system and return the unit to normal operation.  
VOL ADJUST: If choosing VOL ADJUST, use the A-VOL setting to  
specify a turn-on volume.  
Turn-On Volume (A-VOL)  
After selecting “VOL ADJUST”, press the VOL button (5) to access the A-  
VOL setting and then turn the rotary encoder to select the desired turn-on  
volume level. When this option is selected, the unit will revert to the  
adjusted volume each time the unit is turned on.  
18  
20  
SUBWOOFER  
After connecting a subwoofer to the back of the unit, turn the rotary encoder  
to select a crossover frequency: 80, 100 or 120Hz.  
VM8022  
22  
SUB VOL  
LOUD  
21  
The SUB VOL control is only applicable if the unit is connected to an  
optional sub-woofer speaker and is activated. To adjust the sub-woofer level  
from “00” to “33”, press the VOL button (5) until “SUB VOL” appears in the  
display. Turn the rotary encoder clockwise to increase or counter-clockwise  
to decrease the subwoofer level.  
VOL  
AS  
Local/Distant Reception (LO/DX)  
SD/MMC  
When the Local function is on, only radio stations with a strong signal are  
played. To activate Local reception mode, press the LO/DX button (20).  
“Local” will appear on the screen briefly. If pressed again, “DX” appears  
briefly.  
/
1
6
INT  
2
5
RPT  
RDM  
3
4
23  
6
VM8022  
TUNER OPERATION  
remaining five presets on the current band and for presets on the other four  
bands.  
18  
20  
STEREO  
INDICATOR  
VM8022  
22  
LOUD  
21  
VOL  
AS  
PRESET NUMBER  
FM1: 98.10 MHZ 3  
SD/MMC  
/
1
6
INT  
2
5
RPT  
RDM  
3
4
EQUALIZER  
INDICATOR  
23  
Select a Band  
LOUD SETTING INDICATOR  
Press the BAND button (3) to change between three FM and two AM  
bands. Each band stores up to six preset stations.  
Tuning  
Preset Scan  
Manual Tuning  
Press the AS button (14) to scan and play each preset station for 5 seconds  
each. Press AS again to stop preset scan.  
Press the TUNE/TRACK >>| or |<< buttons (17) to move the radio  
frequency number up or down one step.  
Automatic Preset Store  
Seek Tuning  
Press and hold the AS button (14) to select six strong stations and store  
them in the current band using the AUTO PRESET feature. The radio will  
automatically scan all bands and enter strong stations into the preset  
memory positions. After entering the stations into memory, the unit will  
automatically stop at each station for five seconds, allowing you to preview  
each selection. When using the AUTO PRESET feature, the new stations  
replace any stations already stored in preset memory.  
Press and hold the TUNE/TRACK >>| or |<< buttons (17) for more than  
three seconds to seek the next/previous station automatically.  
Preset Stations  
Up to six stations on each band can be stored as presets, which can then  
be instantly recalled by pressing the associated preset button (8-13). To  
store a station, turn the radio on and select the desired band and station.  
Press and hold the desired preset button (numbered one through six on the  
face of the radio) for more than two seconds. When stored, the preset  
number will appear in the display. The station is now stored and can be  
recalled by pressing the corresponding preset button. Repeat for the  
NOTE: You can stop the AUTO PRESET function at any time by  
pressing the AS button again.  
7
VM8022  
DISC/MP3/WMA PLAYBACK  
Fast Forward/Reverse  
18  
20  
Press and hold the TUNE/TRACK >>| or |<< buttons (17) to fast forward or  
fast reverse. Press and hold once for 2X. Press and hold additional times  
for 4X, 8X, 20X or PLAY. Press the play/pause >/|| button (8) to end fast  
forward or reverse and resume normal playback.  
VM8022  
22  
Intro Scan (INT)  
LOUD  
During disc play, press the INT button (9) to select “INTRO” and play the  
first 15 seconds of each track/file. When the desired track is reached, press  
INT again to end the scan and play the selected track.  
21  
VOL  
Repeat (RPT)  
AS  
Press the RPT button (10) multiple times during playback to select from the  
following repeat play options:  
SD/MMC  
VCD/CD: RPT ONE (track), RPT ALL (disc), RPT OFF  
DVD: RPT CHAPTER, RPT TITLE, RPT OFF  
MP3/WMA: RPT ONE (file), RPT DIR (directory/folder), RPT ALL (disc),  
RPT OFF  
/
1
6
INT  
2
5
RPT  
RDM  
3
4
Random (RDM)  
23  
Press the RDM button (11) during playback to select “RANDOM” and play  
all tracks/files in random, shuffled order. Press RDM again to stop random  
play.  
Insert and Eject Disc  
Insert a disc, label side up, into the disc slot (18).  
To stop disc play and eject the disc, press the eject button (4).  
Section Repeat (A-B)  
To repeat a specified section of a track, perform the following steps:  
1. Press the A->B button on the remote control to select the starting point.  
The display will show “REPEAT A-”.  
2. Press A->B when you reach the desired ending point. The display  
shows “REPEAT A-B” and the selected section will play repeatedly.  
NOTE: The unit is designed for play of standard 5” (12 cm.) discs only.  
Do not attempt to use 3” (8 cm.) CD singles in this unit, either with or  
without an adaptor, as damage to the player and/or the disc may  
occur. Such damage will not be covered by the warranty on this  
product.  
To cancel section repeat, press the A->B button again. “A-B CANCEL”  
appears on the display.  
Controlling Disc or File Playback  
Pause  
GOTO Direct Track Access  
Use the GOTO function to access a track directly.  
Press the pause >/|| button (8) to suspend playback. Press the pause >/||  
button again to resume playback.  
1. Press the GOTO button on the remote control. The track number will  
become highlighted.  
2. Use the number keys on the remote control to enter the track number  
directly.  
Track Select  
Press the TUNE/TRACK >>| or |<< buttons (17) for less than one second to  
advance to the next track/file. The selected track number will appear on the  
display.  
3. Press the ENTER button to confirm and begin playback.  
8
VM8022  
Programmed Playback  
TITLE: Press to display the title or chapter list. Use the  
,
,
or  
cursor buttons or the numeric buttons to enter a title or chapter number,  
and then press ENTER to play.  
1. Press the PROG button on the remote control to access the pro-  
grammed playback screen:  
ANGLE: Press to select an alternate viewing angle, if available.  
ZOOM: Press to zoom the picture at X2, X3, X4, X1/2, X1/3 or X1/4, or  
select OFF to return to normal view.  
NOTE: Feature availability is dependent upon DVD embedded  
information.  
Disc Player Error Codes  
If a problem should develop while operating the Disc player, an error code  
may appear on the display panel. This can indicate a number of problems  
with the unit, including a mechanical error or an error in the microprocessor  
control. If an error code appears, try ejecting and reloading the disc into the  
player. While the disc is out of the unit, make sure it is clean and  
2. Use the  
,
,
or cursor buttons to access the fields on the  
“PROG” screen.  
undamaged, and then load it correctly. If this does not solve the problem,  
pressing the RESET button (22) may help, but will erase the time and  
preset memory. If the suggested measures do not solve the problem,  
contact an approved warranty station near you for further assistance.  
3. Use the number buttons on the remote control to enter a track number  
in each field.  
18  
20  
4. Press the >/|| button (8) or highlight “PLAY” on screen and then press  
ENTER to begin playback in the numbered order indicated.  
To delete the list, highlight “CLEAR” and then press ENTER. Press PROG  
to exit the programmed playback screen.  
VM8022  
22  
VCD PlayBack Control (VCD Only)  
LOUD  
21  
If you insert a VCD with playback control, playback automatically starts at  
the beginning of the first track.  
VOL  
Press the PBC button on the remote control to access the VCD menu.  
Use the TUNE/TRACK >>| or |<< buttons (17) to select the desired  
track.  
AS  
Press the (stop) button to return to the menu.  
Press PBC again to exit the menu.  
SD/MMC  
/
1
6
INT  
2
5
RPT  
RDM  
3
4
DVD Playback Features  
The following remote control features are available during DVD playback:  
AUDIO: Press to choose an alternate audio language, if available.  
SUB-T: Press to select an alternate subtitle language, if available.  
23  
9
VM8022  
SYSTEM SETUP MENU  
Table 1: System Setup Menu  
During disc play, press the SETUP button on the remote control to access  
the SYSTEM SETUP menu.  
ASPECT RATIO  
4: 3 PS  
With 16:9 display, the left  
and right sides are cut  
off.  
SYSTEM LANGUAGE VIDEO  
4:3 LB  
16:9  
With 16:9 display, the  
top and bottom are cut  
off.  
Image is presented in  
wide view with a 16:9  
aspect ratio.  
VIDEO FORMAT  
SCREEN SAVER  
ASPECT RATIO  
PASSWORD  
RATING  
PASSWORD  
RATING  
_ _ _ _  
Enter a 4-digit password  
to activate the “Rating”  
feature. The original  
password is “0000”.  
1 KID SAFE  
2 G  
Select the appropriate  
rating level for the  
intended audience.  
DEFAULT  
EXIT SETUP  
3 PG  
You may override higher  
ratings by using your  
password.  
4 PG13  
5 PG-R  
6 R  
Use the  
,
,
or cursor buttons to choose between SYSTEM,  
LANGUAGE, or VIDEO setup options.  
7 NC-17  
8 ADULT  
RESTORE  
Table 1: System Setup Menu  
SYSTEM SETUP  
DEFAULT  
Select “Reset” to restore  
the factory default set-  
tings for the Rating sys-  
tem only.  
VIDEO FORMAT  
NTSC  
PAL  
The color signals are  
output in the standard  
NTSC format.  
LANGUAGE SETUP  
The color signals are  
output in the standard  
PAL format.  
OSD LANGUAGE  
ENGLISH  
GERMAN  
SPANISH  
FRENCH  
Select the appropriate  
on-screen language for  
the DVD  
AUTO  
The color signal output  
is switched automatically  
based on the current  
video input signal -  
NTSC or PAL.  
SCREEN SAVER  
ON  
Turn screen saver on/off.  
OFF  
10  
VM8022  
Table 1: System Setup Menu  
AUDIO LANGUAGE  
ENGLISH  
Choose from audio lan-  
guages contained on the  
DVD If you are watching  
a disc recorded in multi-  
ple languages  
FRENCH  
SPANISH  
PORTUGUESE  
GERMAN  
NOTE: Languages are  
DVD dependent and not  
all languages may be  
supported.  
SUBTITLE LANG  
ENGLISH  
Choose the language  
you would like subtitles  
to appear in (if available)  
FRENCH  
SPANISH  
NOTE: Subtitles are  
DVD dependent and not  
all languages may be  
supported..  
PORTUGUESE  
GERMAN  
OFF  
Turn subtitles off  
MENU LANG  
ENGLISH  
FRENCH  
SPANISH  
PORTUGUESE  
GERMAN  
Select the default lan-  
guage in which you  
would like the DVD  
menu (if applicable) to  
be displayed.  
VIDEO SETUP  
BRIGHTNESS  
CONTRAST  
HUE  
12 - 0  
12 - 0  
+6 to -6  
12 - 0  
8 - 0  
Use the  
/
cursor but-  
tons to set the video out-  
put options  
SATURATION  
SHARPNESS  
EXIT SETUP  
11  
VM8022  
USB/SD OPERATION  
Notes on MP3/WMA Play  
Maximum number of files per disc: 999  
Maximum number of folders per disc: 255  
MP3 and WMA (Windows Media Audio) music files are digital audio files  
that are compressed to allow more files on a single CD. This unit can play  
MP3/WMA directly from files contained on a CD-R/RW or an SD card, USB  
Device using the buttons on the receiver (or remote control) as described  
below.  
MP3/WMA files written in formats other than those listed above will not play  
successfully and their file or folder names will not display properly.  
MP3/WMA Encoder and CD Writer Settings  
Use the following settings when compressing audio data with the MP3  
encoder.  
Many types of software are available for converting audio files into MP3/  
WMA formats. Jensen recommends Nero or Roxio Easy CD Creator.  
Transfer bit rate: 8 - 320 kbps  
Sampling frequency: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz  
This unit can play MP3 (MPEG1, 2, 2.5 Audio Layer 3). However, the MP3  
recording media and accepted formats are limited. When writing MP3/  
WMA, pay attention to the following restrictions.  
When using a CD writer to record MP3/WMA up to the maximum disc  
capacity, disable additional writing. To record an empty disc up to the  
maximum capacity at once, select the “disc at once” option.  
Acceptable Media  
The MP3/WMA recording media acceptable to this unit are CD-ROM, CD-  
R, and CD-RW. The unit will also play MP3, WMA, photo or videos files  
written to SD Cards, USB Devices.  
Entering ID3 Tag  
This unit supports ID3 tag version 2.0.  
For character codes, refer to the table to  
the right.  
Depending on the media type and recording method, some CD-R/RWs may  
be incompatible with this unit. When using CD-RW, use full format rather  
than quick format to prevent malfunction.  
Entering File and Folder Names  
Names using the code list characters  
are the only file names and folder  
names that can be entered and  
displayed. Using any other character will  
cause the file and folder names to be  
displayed incorrectly. The unit  
This unit supports playback of MP3/WMA and CDDA (CDA), Mixed-Mode  
CDs and CD-Extra (including multi-session discs). Discs on which the  
session has not been closed will not play.  
NOTE: This unit supports FAT 16 and FAT 32 file systems. The unit  
supports USB 1.1 only, but will play USB 2.0 devices at USB 1.1 speed.  
recognizes and plays only files with the MP3/WMA extension.  
Acceptable Medium Formats  
NOTE: A file name entered with characters not on the code list may  
not play correctly.  
The following formats are available for the media used in this unit. The  
maximum number of characters used for file name, including the delimiter  
(".") and three-character extension, are indicated in parentheses.  
Electronic Shock Protection  
ISO 9660 Level 1 (11 characters)  
ISO 9660 Level 2 (31 characters)  
Joliet (31 characters)  
10 seconds for CD-DA (CDA)  
>45 seconds for MP3 recorded at 44.1kHz, 128kbps  
>90 seconds for WMA recorded at 44.1kHz, 128kbps  
Romeo (31 characters)  
Bit Rates  
Up to 200 characters can be displayed in the long file name format. For a  
list of available characters, see the instruction manual of the writing  
software and the section “Entering File and Folder Names” that follows. The  
media reproducible on this unit has the following limitations:  
The unit supports bit rates from 32 - 320 kbps.  
Maximum number of nested folders: 8  
12  
VM8022  
MP3 Playing Order  
Loading an SD Card  
Insert the SD card into the SD slot (15) on the front of the radio. The unit will  
read the files on the card automatically.  
When selected for play, files and folders (Folder Search, File Search or  
Folder Select) are accessed in the order in which they were written to the  
media. As a result, the order in which they are expected to be played may  
not match the order in which they are actually played. You may be able to  
set the order in which MP3/WMA files are to be played by assigning file  
names beginning with play sequence numbers such as "01" to "99". For  
example, a medium with the following folder/file hierarchy is subject to  
Folder Search, File Search or Folder Select as shown below.  
To remove the card, first press the SRC button (6) to switch to another  
mode and stop SD playback. Press the SD card to pop it out, then remove  
the card.  
Loading a USB Device  
1. Locate the USB jack (23) located near the bottom right corner on the  
front of the radio.  
2. Pull the left side to lift the rubber cover and reveal the USB jack.  
3. Insert the USB device into the USB jack. The unit will read the files on  
the USB device automatically.  
The VM8022 player will only recognize three folder levels and does not  
display folders containing only other folders. In the example above, the unit  
will display folders 3, 4, 6, and 8, but not 2 and 7 since they do not contain  
any tracks directly. Folder 5 is not recognized at all since it is at the fourth  
level.  
To remove the USB device, press the SRC button (6) to switch to another  
mode and then remove the USB device from the USB jack.  
13  
VM8022  
File Playback  
When a disc or device (SD, USB) containing individual music, video and/or  
photo files is inserted, the following screen appears:  
Folder Name  
File Name  
Folder List  
File List  
Category List  
The category, folder or file list is displayed on screen with the name of the  
file/folder being played displayed on top. The item currently selected will  
appear highlighted.  
You can change which type of items appear for selection on the screen  
using the following buttons:  
AUDIO  
PICTURE  
VIDEO  
1. Use the  
/
cursor buttons to highlight the media type, and then press  
ENTER to confirm.  
2. Use the  
/
cursor buttons to enter a folder list and the  
/
cursor  
buttons to select a folder.  
3. Use the  
/
cursor buttons to enter a file list and the  
/
cursor  
buttons to select a file.  
4. Press ENTER to play the file or (stop) to return.  
For PICTURE, press the >|| button (8) to play a slide show of any pictures  
on the media. Press PROG to select how the next photo is displayed.  
14  
VM8022  
CARE AND MAINTENANCE  
DVD Player  
Disc Care and Handling  
The following guidelines will help you extend the life of your DVD player:  
Dirt, dust, scratches and warpage can cause skips in the playback and  
deterioration of sound quality. Please follow these guidelines to take care of  
your compact discs.  
1. When cleaning the vehicle interior, do not get water or cleaning fluids on  
the unit.  
2. The DVD player will not operate properly in extreme hot/cold or under  
damp conditions. In case of such conditions, wait until the vehicle  
interior reaches a normal temperature or any condensation on the disc  
player lens has evaporated before using the player.  
3. Always remove the disc when the player is not in use.  
4. The unit is designed with a vibration dampening disc mechanism to  
minimize interruption of disc play due to normal vibration in a moving  
vehicle. However, occasional sound skips may occur when driving on  
very rough roads. This will not scratch or damage the disc, and normal  
play will resume when the rough conditions cease.  
1. Do not touch the disc surface.  
2. Never use chemicals such as record sprays or household cleaners to  
clean discs, as they can irreparably damage the disc’s surface.  
3. Discs should be kept in their storage cases when not in use.  
4. Do not expose discs to direct sunlight, high temperatures or high  
humidity for long periods.  
CD-R and CD-RW Capability  
Depending on media type and method of "recording/burning", some CD-R/  
RWs may be incompatible with this unit. After "recording/burning", the  
session must be closed. Please refer to your software's recommended  
procedures for closing a disc/session. Review your recording software to  
familiarize yourself with the correct "recording/burning" procedures. We  
5. Carefully wipe fingerprints, dust and dirt from the disc’s playing surface  
with a soft cloth. Wipe in a straight motion from the inside to the outside  
of the disc.  
6. Do not stick paper, tape or disc labels on disc surfaces, as internal  
damage may occur.  
TM  
TM  
recommend using the latest versions of ROXIO or NERO burning  
software.  
In addition, this unit will only recognize the CDDA (Compact Disc Digital  
Audio), .MP3 and .WMA formats "recorded / burned" onto a CD-R/RW. This  
unit does not support .WAV, .OGG or other formats.  
15  
VM8022  
TROUBLESHOOTING  
Problem  
Cause  
Corrective Action  
Does not operate (dis-  
play does not light)  
No power to yellow wire; no  
power to red wire  
Check connection with test light; check  
vehicle fuse with test light  
Fuse blown  
Fuse blown  
Replace fuse  
No power to unit  
Check/replace fuse  
No/low audio output  
Improper audio output connec- Check wiring and correct  
tion  
Volume set too low  
Speakers damaged  
Increase volume level  
Replace speakers  
Heavily biased volume balance Adjust the channel balance to the center  
position  
Speaker wiring is in contact with Insulate all speaker wiring connections  
metal part of car  
Blows fuses  
No image  
Power wire shorting to ground Make sure wire is not pinched  
Speaker wires shorting to  
ground  
Make sure wire is not pinched  
Incorrect fuse; fuse too small  
Install fuse of correct rating  
Incorrect connection to parking Check Parking SW wiring and correct  
brake wire  
Parking SW is connected but  
parking brake is not engaged  
Stop vehicle in safe place and apply  
parking brake  
Flashing image or inter- DVD is not compatible with cur- Change setup to accommodate disc  
ference appears on  
screen  
rent TV system settings  
Improper video signal connec- Check wiring and correct  
tions  
Prolonged image or  
improper height/width  
ratio display  
Improper aspect ratio setup  
Use correct ASPECT RATIO setting  
Disc does not play back Disc is warped or scratched  
Disc is dirty or wet  
Use disc in good condition  
Clean disc with soft cloth  
Clean laser pickup with cleaning disc  
Use compatible disc  
Laser pickup is dirty  
Incompatible disc is used  
Disc rating exceeds RATING  
limit  
Change RATING settings to lower  
restriction  
Disc region code is not compati- Use disc with proper region code  
ble with unit  
Disc is inserted upside down  
Insert disc with label side up  
Use original disc  
Image blurred, distorted, Disc is illegally copied  
or dark  
16  
VM8022  
SPECIFICATIONS  
Monitor  
CEA Power Ratings  
Screen Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.0" (Measured diagonally)  
Active Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88mm x 50mm  
Screen Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital TFT Panel  
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 (W) X 272 (H) sub pixels  
Dot Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.061 (H) x 0.183 (V)  
Contrast Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100:1  
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 cd/m2  
General  
Auxiliary Input Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10k  
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 to 16VDC, negative ground  
Power Antenna (Blue) . . . . . . . . . . . . . . . . . . . . . . . . .500mA max, current limited protection  
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-20C ~ 65C  
Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-amp, mini ATO type  
DIN Chassis Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 DIN (Double DIN)  
Power Output . . . . . . . . . . . . . . . .13 watts RMS X 4 channels into 4-ohms @ < 1% THD+N  
Signal to Noise Ratio. . . . . . . . . . . . . . . 70dBA below reference (reference: 1 watt, 4-ohms)  
Frequency Response . . . . .20Hz to 20kHz (-3dB), Auxiliary input used as source reference  
Reference Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14.4VDC  
DVD/CD Player  
*Specifications subject to change without notice.  
Compatible Disc Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DVD + R / RW and CD-R / RW  
Compatible Media Formats . . . . . . . . . . . . . . . . . . . . CD-DA, MP3, WMA, VCD, SVCD, AVI,  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPEG1 / 2, XviD, DivX and Kodak picture CD (JPEG)  
Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>95dBA  
Dynamic Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >95dB  
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz to 20 kHz, -3dB  
Channel Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 60dB @ 1 kHz  
Video  
Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .NTSC, PAL (auto-detection)  
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Vp-p (75-ohm)  
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Vp-p (75-ohm)  
FM Tuner  
Tuning Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5MHz - 107.9MHz  
Mono Sensitivity (-30dB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10dBf  
Quieting Sensitivity (-50dB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15dBf  
Alternate Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70dB  
Signal to Noise Ratio @ 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58dB  
Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75dB  
Stereo Separation @ 1 kHz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >27dB  
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Hz - 13 kHz, -3dB  
AM Tuner  
Tuning Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 kHz - 1720 kHz  
Sensitivity (-20dB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15uV  
Signal to Noise Ratio @ 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50dB  
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Hz - 2kHz, -3dB  
17  
VM8022  
18  
Limited Warranty  
DO NOT RETURN THIS PRODUCT TO THE STORE  
CD or Multimedia Radios/Headunits  
Audiovox Electronics Corporation (“the Company”) is committed to  
quality and customer service, and are pleased to offer you this  
Warranty. Please read it thoroughly and contact the Company at 1-800-  
323-4815 with any questions.  
Limitations  
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY  
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND,  
IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE  
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.  
Who is covered?  
The Company extends this warranty to the original retail purchaser of products  
purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or  
Canada. This warranty is not transferable or assignable. Proof of purchase is  
required in the form of an original sales receipt.  
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED  
WARRANTIES,  
INCLUDING  
ANY  
IMPLIED  
WARRANTY  
OF  
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS  
WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY  
HEREUNDER  
INCLUDING  
ANY  
IMPLIED  
WARRANTY  
OF  
What is covered?  
MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24  
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE  
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL  
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS  
OR IMPLIED, WHATSOEVER. No person or representative is authorized to  
assume for the Company any liability other than expressed herein in connection  
with the sale of this product.  
The Company warrants that should this product or any part thereof, under normal  
use, be proven defective in material or workmanship within 12 months from the  
date of original purchase, such defect(s) will be repaired or replaced with a new or  
reconditioned product (at the Company's option) without charge for parts and  
repair labor.  
What is not covered?  
This Warranty does not cover the following:  
Some states do not allow limitations on how long an implied warranty lasts or the  
exclusion or limitation of incidental or consequential damage so the above  
limitations or exclusions may not apply to you. This Warranty gives you specific  
legal rights and you may also have other rights which vary from state to state.  
Damage incurred during shipping or transporting the product to the  
Company or a service center  
Elimination of car static or motor noise  
Defects in cosmetic, decorative or non-operative structural parts  
Correction of antenna problems  
Costs incurred for installation, removal or reinstallation of the product  
Consequential damage to compact discs, USB devices, digital media  
cards, accessories or vehicle electrical systems  
Obtaining Warranty Service  
To obtain repair or replacement within the terms of this Warranty,  
call 1-800-323-4815 for the location of a warranty station serving  
your area.  
Damage caused by improper installation, mishandling, misuse, neglect,  
accident, blown fuse, battery leakage, theft or improper storage  
Products whose factory serial number/bar code label(s) or markings  
have been removed or defaced  
Damage resulting from moisture, humidity, excessive temperature,  
extreme environmental conditions or external natural causes  
You must prepay the initial shipping charges to the Company.  
The Company will pay the return shipping charges for all  
warranteed products returned to an address within the U.S.A.,  
Puerto Rico or Canada.  
Please package the product securely to avoid shipping damage.  
We recommend using a carrier that provides tracking service to  
prevent lost packages. Lost or damaged packages are not  
covered by this warranty.  
Please review the “Care and Maintenance” section of your Installation  
and Operation Manual for additional information regarding the proper  
use of your product.  
Provide a detailed description of the problem(s) for which you  
require service.  
Audiovox Electronics Corporation  
Hauppauge, NY 11788  
Technical Assistance: 1-800-323-4815  
© 2007 Audiovox  
Ver. 042007  
Printed in China  

Audiovox MMD85 User Manual
Audiovox Xpress XMC 10A User Manual
Braun MULTIQUICK 5 MR 530 SAUCE User Manual
Farenheit Technologies T 7020CMM User Manual
Gateway Cable Box CG3100 User Manual
Gitzo G1258LVL User Manual
Harbor Freight Tools 91956 User Manual
Hasselblad H4D200MS User Manual
Hifionics HS2500 1D User Manual
JVC Camcorder TK C700 User Manual