JVC GR SXM540 User Manual

INSTRUCTIONS  
ENGLISH  
LYT0902-002B  
COMPACT VHS CAMCORDER  
GR-SXM745  
GR-SXM540  
For Customer Use:  
Enter below the Model No. and Serial No. which is  
located on the bottom of the camcorder. Retain this  
information for future reference.  
1P2ri0n1teMdKinV*MUalNay*sPiaJ  
Model No.  
Serial No.  
U
COPYRIGHT© 2001 VICTOR COMPANY OF JAPAN, LTD  
Dear Customer,  
Thank you for purchasing the JVC Compact VHS camcorder. Before use, please read  
PRECAUTIONS(pg. 3, 4) to ensure safe use of this product.  
AUTOMATIC DEMONSTRATION  
Automatic Demonstration takes place when “DEMO MODE” is set to “ON”  
(factory-preset).  
Available when the Power Switch @ is set to “ ” or “ ”.  
Performing any operation during the demonstration stops the demonstration temporarily. If no operation  
is performed for more than 1 minute after that, the demonstration will resume.  
DEMO MODE” remains “ON” even if the camcorder power is turned off.  
To cancel Automatic Demonstration, set the Power Switch @ to “ ” and press the MENU Wheel 1 in  
while the demo is in progress. This takes you directly to the demo mode’s Setting Menu (so you will not  
have to go through the main Menu Screen). Rotate the MENU Wheel 1 to select “OFF” and press it.  
NOTES:  
When a tape whose Erase Protection tab is in the position that allows recording is loaded in the  
camcorder, demonstration is not available.  
If you do not detach the Lens Cap, you cannot see the actual changes of the Automatic Demonstration  
activated on the LCD monitor or viewfinder.  
1
PRECAUTIONS  
SAFETY PRECAUTIONS  
CAUTIONS  
CAUTION  
This camcorder is designed to be used with  
NTSC-type color television signals. It cannot be  
used for playback with a television of a different  
standard. However, live recording and LCD  
monitor/viewfinder playback are possible  
anywhere.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
Use the JVC BN-V11U/V12U/V20U/V400U  
battery packs and, to recharge them or to supply  
power to the camcorder from an AC outlet, use  
the provided multi-voltage AC Adapter.  
(An appropriate conversion adapter may be  
necessary to accommodate different designs of  
AC outlets in different countries.)  
The lightning flash with arrowhead symbol, within an  
equilateral triangle, is intended to alert the user to the  
presence of uninsulated "dangerous voltage" within the  
product's enclosure that may be of sufficient magnitude  
to constitute a risk of electric shock to persons.  
The exclamation point within an equilateral triangle is  
intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in  
the literature accompanying the appliance.  
NOTES:  
The rating plate (serial number plate) and safety  
caution are on the bottom and/or the back of the  
main unit.  
The rating information and safety caution of the  
AC Adapter are on its upper and lower sides.  
WARNING:  
TO REDUCE THE RISK OF FIRE  
OR ELECTRIC SHOCK, DO NOT  
EXPOSE THIS APPARATUS TO  
RAIN OR MOISTURE.  
ATTENTION:  
The product that you have purchased is powered  
by a rechargeable battery. The battery is recycla-  
ble. At the end of its useful life, under various state  
and local laws, it may be illegal to dispose of this  
battery into the municipal waste stream. Check  
with your local solid waste officials for details in  
your area for recycling options or proper disposal.  
This product has a fluorescent lamp that  
contains a small amount of mercury. Disposal of  
these materials may be regulated in your  
community due to environmental considerations.  
For disposal or recycling information please  
contact your local authorities, or the Electronics  
Industries Alliance:  
<http://www.eiae.org>  
Cassettes marked  
and  
can be used used with this camcorder.  
3
The EPA certified RBRC® Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates JVC  
is voluntarily participating in an industry program to collect and recycle these batteries at the end of  
their useful life, when taken out of service in the United States. The RBRC® program provides a  
convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream,  
which may be illegal in your area. Please call 1-800-8-BATTERYfor information on Ni-Cd battery  
recycling and disposal bans/restrictions in your area. JVCs involvement in this program is part of our  
commitment to preserving our environment and conserving our natural resources.  
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all  
sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).  
Do not block the ventilation holes.  
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)  
No naked flame sources, such as lighted candles, should be placed on the apparatus.  
When discarding batteries, environmental problems must be considered and the local rules or laws  
governing the disposal of these batteries must be followed strictly.  
The apparatus shall not be exposed to dripping or splashing.  
Do not use this equipment in a bathroom or places with water.  
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower  
vases, potted plants, cups etc.) on top of this unit.  
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)  
IMPORTANT SAFETY INSTRUCTIONS  
(1) Read these instructions.  
(2) Keep these instructions.  
(3) Heed all warnings.  
(10) Use only with the cart, stand,  
tripod, bracket, or table  
specified by the manufac-  
turer, or sold with the  
apparatus. When a cart is  
used, use caution when  
moving the cart/apparatus combination to  
avoid injury from tip-over.  
(4) Follow all instructions.  
(5) Do not use this apparatus near water.  
(6) Clean only with dry cloth.  
(11) Unplug this apparatus during lightning  
storms or when unused for long periods of  
time.  
(7) Do not block any ventilation openings. Install  
in accordance with the  
manufacturers instructions.  
(12) Refer all servicing to qualified service  
personnel. Servicing is required when the  
apparatus has been damaged in any way,  
such as power-supply cord or plug is  
damaged, liquid has been spilled or objects  
have fallen into the apparatus, the  
apparatus has been exposed to rain or  
moisture, does not operate normally, or has  
been dropped.  
(8) Do not install near any heat sources such as  
radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce  
heat.  
(9) Only use attachments/accessories specified  
by the manufacturer.  
4
INDEX  
A
P
AC Adapter.................................................................pg. 6  
Animation Recording ..........................................pg. 21, 24  
Audio Dubbing .........................................................pg. 24  
Auto Date Record ....................................................pg. 19  
Auto Focus ...............................................................pg. 18  
Auto Shut Off ........................................................... pg. 11  
Picture Stabilizer ......................................................pg. 12  
Playback .................................................................. pg. 11  
Playback Special Effects ..........................................pg. 14  
Playback Zoom ........................................................pg. 24  
Program AE with Special Effects .............................pg. 23  
Provided Accessories................................................ pg. 2  
B
Q
Battery Pack .........................................................pg. 6, 26  
Blue Filter Effect ...................................................... pg. 23  
Brighten The Image .................................................pg. 18  
Brighten The LCD Monitor ....................................... pg. 11  
Quick Review ...........................................................pg. 13  
R
Recording, Advanced Features..........................pg. 22, 23  
Recording, Start/Stop............................................... pg. 11  
Recording Format (S-VHS/S-VHS ET) ....................pg. 20  
Recording Mode .......................................................pg. 20  
Record-Standby ....................................................... pg. 11  
Red Filter Effect .......................................................pg. 23  
Remote Control ........................................................pg. 24  
Retake......................................................................pg. 13  
Rewind The Tape ..................................................... pg. 11  
C
Cassette Adapter .....................................................pg. 16  
Charge Marker ...........................................................pg. 6  
Charging The Battery Pack ........................................pg. 6  
Classic Film Effect....................................................pg. 23  
Clean The Camcorder ..............................................pg. 27  
Connection To a VCR/TV .........................................pg. 15  
Connection To A PC .................................................pg. 16  
Counter Memory ......................................................pg. 14  
S
Self-Recording ......................................................... pg. 11  
Sepia Mode ..............................................................pg. 23  
Shoulder Strap Attachment ........................................pg. 8  
Snapshot ..................................................................pg. 12  
Snapshot During Playback .......................................pg. 12  
Solarization Effect ....................................................pg. 23  
Specifications ...........................................................pg. 28  
Sports Mode .............................................................pg. 23  
Still Playback............................................................ pg. 11  
Stretch Effect ...........................................................pg. 23  
Strobe Effect ............................................................pg. 23  
Super LoLux (S.LX) .................................................pg. 19  
Super VHS Expansion Technology ..........................pg. 20  
D
Darken The Image ...................................................pg. 18  
Darken The LCD Monitor ......................................... pg. 11  
Date/Time Display ....................................................pg. 19  
Date/Time Settings.....................................................pg. 7  
Demonstration Mode ............................................pg. 1, 21  
Digital Effects ...........................................................pg. 23  
Digital Zoom .............................................................pg. 20  
Diopter Adjustment.....................................................pg. 8  
E
Electronic Fog Filter Mode .......................................pg. 23  
Erase Protection ........................................................pg. 8  
Exposure Control .....................................................pg. 18  
T
Tape Counter ...........................................................pg. 14  
Tape Dubbing ...........................................................pg. 15  
Tape Length Setting .................................................pg. 21  
Tele Macro ...............................................................pg. 21  
Time Base Corrector ............................................... pg. 14  
Time-Lapse Shooting .........................................pg. 21, 24  
Tracking ...................................................................pg. 14  
Tripod Mounting .........................................................pg. 8  
Twilight Mode ...........................................................pg. 23  
F
Fade-In/Out ..............................................................pg. 22  
Fast-Forward Tape ................................................... pg. 11  
G
Grip Adjustment .........................................................pg. 8  
H
High Speed Shutter Mode........................................pg. 23  
I
U
Insert Editing ............................................................pg. 24  
Instant Titles .............................................................pg. 19  
Unload A Tape ............................................................pg. 8  
V
L
Video Echo Effect.....................................................pg. 23  
Video Light ...............................................................pg. 13  
Viewfinder Adjustment ...............................................pg. 8  
LCD Monitor/Viewfinder, Indications ..............pg. 9, 10, 17  
Load A Tape ...............................................................pg. 8  
M
W
Manual Focus ..........................................................pg. 18  
Menu Screen....................................................pg. 18 21  
Monotone Effect .......................................................pg. 23  
Mosaic Effect ...........................................................pg. 23  
White Balance Adjustment .......................................pg. 19  
Wide Mode ...............................................................pg. 20  
Wipe-In/Out ..............................................................pg. 22  
Z
N
Zooming ...................................................................pg. 13  
ND Effect Mode ........................................................pg. 23  
Nega/Posi Mode ......................................................pg. 23  
Night-Alive ................................................................pg. 22  
5
USING THE BATTERY PACK  
Perform step 1) of CHARGING THE BATTERY  
PACK.  
GETTING STARTED  
Hook on.  
Approximate recording time (unit: min.)  
Battery pack  
Viewfinder on  
LCD monitor on  
BN-V11U  
95  
(50)  
80  
(45)  
Push in.  
BN-V12U  
(optional)  
95  
(50)  
80  
(45)  
BN-V20U  
(optional)  
150  
(85)  
135  
(75)  
BATTERY RELEASE Switch  
BN-V400U  
(optional)  
360  
(205)  
315  
(190)  
(
):when the video light is on  
Battery pack  
Power Switch  
USING AC POWER  
Connect the AC Adapter to the camcorder (step  
2) and 3) of CHARGING THE BATTERY PACK).  
To DC IN  
connector  
The provided AC Adapter features automatic  
voltage selection in the AC range from 110 V to  
240 V.  
AC Adapter  
To AC outlet  
ATTENTION  
CHARGING THE BATTERY PACK  
Before detaching the power source,  
make sure that the camcorders power is turned  
off. Failure to do so can result in a camcorder  
malfunction.  
1) Hook the end of the battery pack to the  
camcorder and push the battery in until it locks  
in place.  
If the battery pack is attached in the wrong  
position, a malfunction may occur.  
2) Set the Power Switch @ to OFF. Connect the  
AC Adapter to the DC IN connector 9.  
3) Plug the AC Adapter into an AC outlet. The  
CHARGE lamp * blinks to indicate charging  
has started.  
4) When the CHARGE lamp * stops blinking but  
stays lit, charging is finished. Unplug the AC  
Adapter from the AC outlet. Disconnect the AC  
Adapter from the camcorder.  
REFRESH:  
Be sure to fully discharge a battery pack before  
recharging or storing it for a long period of time,  
otherwise the battery performance will be reduced.  
1) Perform steps 1) through 3) of CHARGING  
THE BATTERY PACK.  
2) Press REFRESH r for over 2 seconds. The  
REFRESH lamp ( blinks to indicate  
discharging has started.  
3) When discharging is finished, charging  
automatically starts and the CHARGE lamp *  
blinks.  
To Detach The Battery Pack . . .  
... slide BATTERY RELEASE 8 and pull out the  
battery pack.  
Charge marker helps you remember  
whether the battery pack has been  
charged or not. Two colors are provided  
(red and black)you choose which one  
means charged and which means  
discharged.  
Battery pack  
BN-V11U  
Charging time  
approx. 1 hr. 30 min.  
approx. 1 hr. 30 min.  
approx. 2 hrs. 20 min.  
approx. 4 hrs. 30 min.  
BN-V12U (optional)  
BN-V20U (optional)  
BN-V400U (optional)  
Charging times are for a fully discharged battery pack.  
6
During charging or discharging, the camcorder  
cannot be operated.  
Charging and discharging is not possible if the  
wrong type of battery is used.  
Date/Time Settings  
1) Set the Power Switch @ to “ ”.  
2) Press the MENU Wheel 1 in. The Menu  
Screen appears.  
When charging the battery pack for the first time  
or after a long storage period, the CHARGE lamp  
* may not light. Remove the battery pack from  
the camcorder, then try charging again.  
If a fully-charged batterys operation time remains  
extremely short, the battery is worn out. Please  
purchase a new one.  
Perform charging where the temperature is  
between 10°C and 35°C (50°F and 95°F). 20°C to  
25°C (68°F to 77°F) is the ideal temperature range  
for charging. If the environment is too cold,  
charging may be incomplete.  
Charging time varies according to the ambient  
temperature and the status of the battery pack.  
Since the AC Adapter processes electricity  
internally, it becomes warm during use. Be sure to  
use it only in well-ventilated areas.  
3) Rotate the MENU Wheel 1 to select  
4TO SYSTEM MENUand press it to display  
SYSTEM MENU. Rotate the MENU Wheel 1 to  
select 4NEXTand press it to display the next  
page.  
4) Rotate the MENU Wheel 1 to select DATE/  
TIMEand press it. The DATE/TIME Menu  
appears.  
5) To set YEAR, MONTH, DAYor TIME”  
(hour/minute), rotate the MENU Wheel 1 to  
select the desired item, and press it. When the  
setting begins blinking, rotate the MENU Wheel  
1 until the correct setting appears and then  
press it. The setting stops blinking.  
6) When none of these settings (YEAR,  
MONTH, DAY, TIME) blinks, rotate the  
MENU Wheel 1 to select EXIT, and press it.  
The Menu Screen reappears with the highlight  
bar on 4RETURN.  
The following operation stops charging or  
discharging:  
Set the Power Switch @ to “  
, “ ” or “ ”.  
7) Press the MENU Wheel 1 in to close the Menu  
Screen.  
Disconnect the AC Adapter from the camcorder.  
Unplug the AC Adapter from the AC outlet.  
Detach the battery from the camcorder.  
Using the optional AA-V15 AC Power Adapter/  
Charger, you can charge the BN-V11U/V12U/  
V20U/V400U battery pack without the camcorder.  
However, it cannot be used as an AC adapter.  
To avoid interference with reception, do not use  
the AC Adapter near a radio.  
To display the date and time in the camcorders  
display and on a connected TV, see DATE/TIME  
DISP. (pg. 19) in CAMERA MENU.  
The date/time cannot be stored in memory if the  
built-in clock battery runs out. Consult an  
authorized JVC dealer for replacement, or set the  
date/time as necessary before you start shooting.  
Recording time is reduced significantly when  
Zoom or Record-Standby mode is engaged  
repeatedly or the LCD monitor is used repeatedly.  
Before extended use, it is recommended that you  
prepare enough battery packs to cover 3 times the  
planned shooting time.  
1
@
DATE / T I ME  
YEAR  
MONTH  
DAY  
2002  
JUN  
28  
:
T I ME  
PM  
8
20  
12-hour indication  
with AM or PM  
EX I T  
7
Grip Adjustment  
1) Separate the Velcro strip.  
Tripod Mounting  
Align the screw and camera direction stud on the  
2) Pass your right hand through the loop and grasp tripod with the tripod mounting socket W. Then  
the grip.  
tighten the screw.  
3) Adjust so that your thumb and fingers can easily  
operate the Recording Start/Stop Button ! and  
Power Zoom Lever 3. Refasten the Velcro strip.  
CAUTION  
When using a tripod, be  
sure to open and extend  
its legs fully to stabilize  
the camcorder. To  
prevent damage to the  
unit caused by falling  
over, do not use a  
3
!
small-sized tripod.  
Viewfinder Adjustment  
Loading/Unloading A Cassette  
1) Set the Power Switch @ to “ ” or “ ”.  
2) Turn the Diopter Adjustment Control o until the  
indications in the viewfinder are clearly focused.  
1) Open the LCD monitor fully. Slide EJECT t  
until the cassette holder opens. Do not use force  
to open.  
2) Insert or remove a cassette. When inserting,  
make sure the label is facing outward.  
appears when a cassette is loaded.  
q
3) Press the Close button i to close the cassette  
holder until it locks into place. Close the LCD  
monitor.  
180°  
Closing the LCD monitor while the cassette holder is  
still open may cause damage to the LCD monitor.  
Make sure the erase protection tab is in the position  
that allows recording. If not, slide the tab. Some  
cassettes have removable tabs. If the tab has been  
removed, cover the hole with adhesive tape.  
The cassette holder cannot be opened while the  
camcorder is in the record mode or detached from  
the power source.  
PAUSE  
Cassette holder  
Shoulder Strap Attachment  
t
Thread the strap through the eyelet y, then fold it  
back and thread it through the buckle. Repeat the  
procedure to attach the other end of the strap to  
the other eyelet y, making sure the strap is not  
twisted. Adjust the length.  
Gear  
i
y
Turn to take  
up slack.  
Erase Protection tab  
8
CONTROLS, CONNECTORS AND INDICATORS  
Eyepiece  
Refer to this diagram while reading the instructions.  
1
2
3
4
During shooting  
*
(
#
$
)
%
q
^
w
&
5
Keep the lens  
cap attached to  
the camcorder.  
6
7
Cassette  
holder  
e
r t  
8
9 0 !  
@
LCD monitor  
Viewfinder  
o
90°  
y
u
180°  
Turn the gear to  
take up slack.  
Speaker  
p
y
Transmitted beam  
effetive area  
i
180°  
Erase  
protection tab  
(
)
5m 16ft  
30°  
Q
30°  
E
R
Microphone  
Remote control  
(GR-SXM745 only)  
Video light  
T
U
P
a
s
d
f
Y
I
O
W
LCD Monitor/Viewfinder Indications  
During Recording  
During Playback  
1
2 3  
4
5
q w e  
r t y u i  
6
120M I N  
REC SP  
SET  
T
40  
S
ET  
SP  
4
:
:
TBC  
MONOTONE  
1
2 3 4 5  
7
444  
1
N I GHT 10  
x
AT  
^
*
8
0
@
+
02  
&
(
9
!
SVHS REC  
PAUSE  
MWB  
1X  
:
:
5
M I N  
M
0
1 2 3 4  
o
p
1 / 2  
S
)
– – – – – – – – – –  
+
6
BR I GHT  
#
%
$
CONGRATULAT I ONS  
:
:
––––6––––  
+
DEC 25. 01 AM 11 45 18  
VOLUME  
pg. 25 for Warning Indications .  
9
1 MENU Wheel [, +] ..................................... pg. 18  
BRIGHT Wheel [, +] .................................. pg. 11  
TRACKING Wheel [, +] ............................. pg. 14  
2 Snapshot Button [SNAPSHOT] ..................... pg. 12  
3 Power Zoom Lever [T/W] ............................ pg. 13  
Speaker Volume Control [VOL.] .................. pg. 11  
O REC TIME Button ........................................ pg. 24  
ANIM. Button ............................................... pg. 24  
P START/STOP Button (Functions the same as !)  
a FF Button (Functions the same as &)  
s PAUSE Button ............................................... pg. 11  
d A.DUB Button ................................................ pg. 24  
f INT.TIME Button .......................................... pg. 24  
SELF TIMER Button (non-functional)  
4 Picture Stabilizer Button  
[P.STABILIZER] ........................................... pg. 12  
Time Base Corrector Button [TBC].............. pg. 14  
5 S-Video Output Connectors [S] ..................... pg. 15  
6 Audio Output Connector [A] .......................... pg. 15  
7 Video Output Connector [V] .......................... pg. 15  
1 Tape Remaining Time ................................... pg. 21  
2 Recording Mode Indicator ............................. pg. 20  
3 Digital Effect Indicator ................................. pg. 23  
Program AE Indicator .................................. pg. 23  
Night-Alive Indicator .................................... pg. 22  
Fade/Wipe-Standby Indicator ...................... pg. 22  
4 Recording Format Indicator (S/S-ET)............ pg. 20  
5 Tape Length Indicator .................................... pg. 21  
6 Zoom Indicator Bar ........................................ pg. 13  
Zoom Level Indicator  
8 Battery Release Switch  
[BATTERY RELEASE] .................................... pg. 6  
9 DC IN Connector ............................................. pg. 6  
0 Digital Connector [DIGITAL]  
! Recording Start/Stop Button ......................... pg. 11  
@ Power Switch [  
, OFF,  
,
] .............. pg. 11  
# Video Light Switch  
Approximate Zoom Ratio  
[LIGHT OFF/AUTO/ON] ................................ pg. 13  
$ Stop Button [STOP] ....................................... pg. 11  
% Retake Rewind Button [RETAKE R] ............ pg. 13  
7 Recording Indicator ....................................... pg. 11  
8 Digital Effect Indicator ................................... pg. 23  
9 Program AE Indicator .................................. pg. 23  
Night-Alive Indicator .................................... pg. 22  
Quick Review Button [  
R] ...................... pg. 13  
Rewind Button [R] ....................................... pg. 11  
0 Fade/Wipe-Standby Indicator ........................ pg. 22  
! Picture Stabilizer Indicator ............................ pg. 12  
@ Interval Time/Recording Time Indicator ........... pg. 21  
# Bright Level Indicator .................................... pg. 11  
$ Instant Title Display ....................................... pg. 19  
% Date/Time Display ......................................... pg. 19  
^ Focus Indicator .............................................. pg. 18  
& Exposure Control Level Counter ................... pg. 18  
* White Balance Mode Indicator ...................... pg. 19  
^ Play/Pause Button ......................................... pg. 11  
& Retake Forward Button [RETAKE F] ........... pg. 13  
Fast-Forward Button [F] .............................. pg. 11  
* CHARGE Lamp ............................................... pg. 6  
( POWER/REFRESH Lamp .............................. pg. 6  
) Fade/Wipe Button [FADE/WIPE] ................. pg. 22  
Counter Reset/Memory Button  
[COUNTER R/M] ......................................... pg. 14  
q Program AE Button [P.AE] ............................. pg. 23  
w Digital Effect Button [DIGIFECT] ................... pg. 23  
e NIGHT-ALIVE Button .................................... pg. 22  
r REFRESH Button ............................................ pg. 6  
t EJECT Switch ................................................. pg. 8  
y Shoulder Strap Eyelets ................................... pg. 8  
u Battery Pack Mount ......................................... pg. 6  
i Close Button .................................................... pg. 8  
o Diopter Adjustment Control ............................. pg. 8  
p Camera Sensor  
( S-VHS/S-VHS ET Recording  
Indicator ........................................................ pg. 20  
) Record-Standby Mode Indicator ................... pg. 11  
q •  
: Cassette Indicator................................. pg. 8  
w: Insert Editing Indicator* .......................... pg. 24  
w TBC Indicator ................................................ pg. 14  
e Playback Special Effect Indicator .................. pg. 14  
r Recording Format Indicator (S/S-ET)............ pg. 20  
t Tape Counter* ......................................... pg. 14, 24  
y Recording Mode Indicator (SP/EP) ............... pg. 20  
u Tape Running Indicator  
Be careful not to cover this area; a sensor  
necessary for shooting is built-in here.  
Remote Sensor* ...................................... pg. 9, 17  
Q Grip Strap ........................................................ pg. 8  
W Tripod Mounting Socket .................................. pg. 8  
E Infrared Beam Transmitting Window ......... pg. 9, 17  
R ZOOM (T/W) Buttons .............................. pg. 13, 24  
T PLAY Button .................................................. pg. 11  
Y REW Button (Functions the same as %)  
4
: Playback  
3
2
6
: Fast-Forward/Shuttle Search  
: Rewind/Shuttle Search  
: Pause  
e4  
: Audio Dubbing*  
i Tracking Indicator .......................................... pg. 14  
o Tape Counter* ............................................... pg. 24  
p BRIGHT: Bright Level Indicator ................... pg. 11  
VOLUME: Speaker Volume Indicator ........... pg. 11  
* GR-SXM745 only.  
U STOP Button (Functions the same as $)  
I INSERT Button .............................................. pg. 24  
10  
RECORDING  
PLAYBACK  
Set REC MODE, S-VHS (S-VHS ET), TAPE  
LENGTH and DATE/TIME in SYSTEM MENU.  
(pg. 18 21, MENU SETTINGS)  
1 Load a tape (pg. 8, Loading/Unloading A  
Cassette).  
2 Set the Power Switch @ to “  
. To start  
playback, press 4/6 ^ or T.  
1 Remove the lens cap. Set the Power Switch @  
to “ ” or “ ”.  
Shooting while using the viewfinder: Make sure  
the LCD monitor is closed and locked.  
Shooting while using the LCD monitor: Make  
sure the LCD monitor is fully open.  
The camcorder enters the Record-Standby mode  
and PAUSE) is displayed.  
The viewfinder and LCD monitor cannot be used  
simultaneously on this camcorder. Therefore,  
when opening the LCD monitor and tilting it  
upward to 180°, you cannot view any image in the  
viewfinder, however you can shoot yourself while  
viewing your own image in the LCD monitor.  
To stop playback temporarily (Still Playback), press  
4/6 ^ or s. To stop playback, press 5 $. Press  
2
% to rewind, or  
3
& to fast-forward the tape.  
High-speed picture search (Shuttle Search) is  
possible by pressing % or & during  
playback (holding % or & down during  
2
3
2
3
playback continues search until released). To  
resume normal playback, press 4/6 ^ or T.  
For VIDEO RECORDING/VIDEO PLAYBACK  
The camcorder shuts off automatically after about  
5 minutes in the Record-Standby or Stop mode.  
To turn on again, set the Power Switch @ to  
OFF, then to “ ”, “ ” or “  
When the Power Switch @ is set to “ ”, “ ” or  
and the LCD monitor* is opened at an  
.  
2 Press the Recording Start/Stop Button !.  
7
appears while recording is in progress.  
angle of 60 degrees or more, the LCD monitor  
switches on and the viewfinder switches off  
automatically to save power.  
To stop recording, press the Recording Start/Stop  
Button !. The camcorder re-enters the Record-  
Standby mode.  
The playback picture can be viewed in the  
viewfinder (with the LCD monitor shut), on the  
LCD monitor or on a connected TV (pg. 15,  
Connections To A TV/VCR).  
To Adjust The Brightness Of The LCD Monitor,  
rotate the BRIGHT Wheel 1 until the bright level  
indiator # on the display moves and the  
appropriate brightness is reached.  
To remove the indications, pg. 21, DISPLAY or  
Tapes recorded on S-VHS or S-VHS ET  
(pg. 18, 20) cannot be played back correctly  
on a normal VHS VCR.  
To playback on a regular VHS VCR, use a VHS  
tape and select S-VHS ET (OFF) in SYSTEM  
MENU (pg. 18, 20).  
OSD OUTPUT in SYSTEM MENU.  
To control the speaker volume, slide VOL. 3  
towards +to turn up, or towards “–” to turn  
down. While shooting, sound is not heard from  
the speaker.  
If TBC (pg. 14) is engaged during Still  
Playback, noise bars will not appear.  
11  
Picture Stabilizer  
To compensate for unstable images caused by  
camera-shake, particularly at high magnification.  
BASIC FEATURES  
Snapshot  
You can record still images that look like photo-  
graphs onto a tape.  
1) Press P. STABILIZER 4.  
2) To switch off the Picture Stabilizer, press  
P. STABILIZER 4. !disappears.  
Accurate stabilization may not be possible in  
certain conditions including excessive hand  
shake.  
! appears.  
1) Perform step 1 of RECORDING(pg. 11).  
2) Press SNAPSHOT 2.  
There is a momentary camera shutter-type  
blackout together with the sound effect of a  
shutter closing.  
! appears blinking if the Stabilizer cannot be  
used.  
Snapshot is also available during playback.  
However, the shutter sound is not heard.  
This function cannot be activated during the  
Night-Alive, CLASSIC FILM, STROBEand  
VIDEO ECHOmodes (pg. 23, Digital  
Effects).  
12  
DANGER  
Zooming  
To produce the zoom in/out effect. Digital circuitry  
extends the maximum magnification offered by  
optical zoom. This system is called Digital Zoom.  
Slide the Power Zoom Lever 3 towards Tto  
zoom in, or Wto zoom out.  
The video light can become  
extremely hot.  
Do not touch it either while in  
operation or soon after turning it off,  
otherwise serious injury may result.  
Do not place the camcorder into the carrying case  
immediately after using the video light, since it  
remains extremely hot for some time.  
When operating, keep a distance of about 30 cm  
(11-13/16) between the video light and people or  
objects.  
Do not use near flammable or explosive  
materials.  
It is recommended that you consult your nearest  
JVC dealer for replacing the video light.  
The further you slide the Power Zoom Lever 3,  
the quicker the zoom action.  
Focusing may become unstable during Zooming.  
In this case, set the zoom while in Record–  
Standby, lock the focus by using the manual focus  
(pg. 18, FOCUS in CAMERA MENU), then  
zoom in or out in Record mode.  
The zoom level indicator 6- moves during  
zoom. Once the zoom level indiator 6-  
reaches the top, all magnification from that point  
is through digital processing.  
When using Digital Zoom, the quality of image  
may suffer. To deactivate Digital Zoom, set  
D.ZOOM(pg. 20) to OFFin SYSTEM  
MENU.  
Quick Review  
To check the end of the last recording.  
1) Make sure the camcorder is in the Record–  
Standby mode.  
Digital zoom cannot be used when the VIDEO  
ECHOmode (pg. 23, Digital Effects) is  
activated.  
2) Press  
2
% and release quickly.  
Tape is rewound for approx. 2 seconds and  
played back automatically, then pauses in  
RecordStandby mode for the next shot.  
Distortion may occur at the start of playback. This  
is normal.  
Video Light  
To brighten the scene when natural lighting is too  
dim.  
Retake  
To re-record certain segments.  
Set LIGHT OFF/AUTO/ON # as required:  
OFF : Turns off the light.  
1) Make sure the camcorder is in the Record–  
Standby mode.  
AUTO: Automatically turns on the light when the  
camcorder senses insufficient lighting on  
the subject.  
ON : Always keeps the light on as long as the  
camcorder is turned on.  
It is recommended to set M.W.B. (pg. 19) to  
in CAMERA MENU when you use the video  
light.  
2) Press and hold either RETAKE % or & to reach  
the start point for new recording. Pressing  
3
& forwards the tape and pressing  
reverses it.  
2
%
3) Press the Recording Start/Stop Button ! to  
start recording.  
Noise bars appear and pictures may become  
monochrome or darken during Retake. This is  
normal.  
Even if the battery indicator (  
) does not blink  
if the battery packs charge is low, the camcorder  
may turn off automatically when you turn on the  
video light, or when you start recording with the  
video light turned on.  
When LIGHT OFF/AUTO/ON # is set to AUTO:  
Depending on the lighting conditions, the video  
light may keep turning on and off. Set LIGHT  
OFF/AUTO/ON # to ON or OFF as required.  
While the Sportsor High Speed Shuttermode  
is engaged, the light is likely to stay on. While  
the Twilightmode is engaged, the light will not  
activate. (pg. 23, Program AE with Special  
Effects)  
13  
Tracking  
Counter Memory  
Eliminates noise bars that appear on-screen during Makes it easier to locate a specific tape segment.  
playback. To activate Manual Tracking:  
1) Press COUNTER R/M ) and hold for more than  
1) Press the TRACKING Wheel 1 for approx.  
2 seconds. MTi appears.  
1 second. The counter t resets to 0:00:00.  
2) Press COUNTER R/M ) for less than 1 second.  
Mappears.  
2) Rotate the TRACKING Wheel 1 so that the  
noise bars disappear.  
3) After recording or playback, press 5 $, then  
To return to Auto Tracking, press the TRACKING  
Wheel 1 for approx. 2 seconds or set the Power  
2
%. The tape automatically stops at or close  
to 0:00:00.  
Switch @ to OFFand then “  
again. ATi  
4) Press 4/6 ^ to start playback.  
blinks. When Auto Tracking finishes, the indication The counter memory functions in the Fast-  
disappears.  
Forward and Rewind modes.  
When noise bars appear during playback, the  
camcorder enters the Auto Tracking mode and  
ATi appears.  
To disable the counter memory function, press  
COUNTER R/M ) for less than 1 second so that  
Mdisappears.  
Manual Tracking may not work with tapes  
recorded on other VCRs or camcorders.  
Playback Special Effects  
Allows you to add creative effects to the playback  
image. (pg. 23, Digital Effects)  
1) Activate TBCand Auto Tracking.  
2) Press DIGIFECT w repeatedly until the desired  
mode e appears.  
To cancel the effect, select OFF.  
NEGA POSI, MOSAIC and STRETCH are not  
available.  
Playback Special Effects do not work during  
Shuttle Search (pg. 11).  
The selected effect mode cannot be changed  
during Still Playback (pg. 11).  
TBC (Time Base Corrector)  
Removes jitter from fluctuating video signals to  
deliver a stable picture even with old tapes.  
To activate/release the TBC mode, press TBC 4  
during playback for more than 1 second. When the  
TBC mode is activated, TBCw is displayed.  
The TBCindicator w turns green (gray with a  
camcorder equipped with a black/white  
viewfinder) while TBC is working, and white while  
TBC is not operative.  
TBC does not work during Still Playback and  
Shuttle Search (pg. 11).  
It may take a few seconds before TBC actually  
starts working.  
The picture may be distorted if the TBC mode is  
activated or deactivated at the edit-in/-out points  
or when normal playback resumes after Still  
Playback or Shuttle Search (pg. 11).  
If the playback picture is distorted when TBC is  
set to on, turn off TBC.  
14  
Connections To A TV/VCR  
1) Make sure all units are turned off.  
Tape Dubbing  
1) Connect the camcorder and the VCR  
2) Connect the camcorder to a TV or VCR using  
optional video and audio cables. If using both  
TV and VCR, connect the VCR output to the TV  
input.  
3) Turn on all units. Set the VCR to its AUX input  
mode, and set the TV to its VIDEO mode.  
Use the AC Adapter as the power supply.  
The S-Video cable connection can improve the  
dubbed picture quality. The S-Video cable is  
optional. Be sure to use the following cable:  
YTU94146A S-Video cable.  
Consult the JVC Service Center described on  
the sheet included in the package for details  
on its availability. Make sure to connect the  
end with a core filter to the camcorder. The  
core filter reduces interference.  
(Connections To A TV/VCR). Set the Power  
Switch @ to “  
, turn on the VCRs power,  
and insert the appropriate cassettes in the  
camcorder and the VCR. Engage the VCRs  
AUX and Record-Pause modes.  
2) Press 4/6 ^ to find a spot just before the edit-  
in point. Once it is reached, press 4/6 ^ again.  
3) Press 4/6 ^ and engage the VCRs Record  
mode.  
4) Engage the VCRs Record-Pause mode and  
press 4/6 ^.  
Repeat steps 2) through 4) for additional editing,  
then stop the VCR and camcorder when finished.  
Be sure to adjust the TV sound volume to its  
minimum level to avoid a sudden burst of sound  
when the camcorder is turned on.  
If you have a TV or speakers that are not  
specially shielded, do not place the speakers  
adjacent to the TV as interference will occur in the  
camcorder playback picture.  
White to  
Audio  
To S-Video  
Output 6  
Output 5  
Yellow to  
Video Output 7  
Connector cover  
A/V cable  
S-Video cable  
(optional)  
TV  
To TV or VCR  
White to  
Audio Input  
To S-Video  
Input  
VCR  
Yellow to  
Video Input  
15  
Using The Cassette Adapter  
Use this to play back an S-VHS-C/VHS-C video  
Connection To A Personal Computer  
You can transfer image data from the camcorder to  
cassette recorded with this camcorder on a S-VHS/ a PC using Digital Photo Navigator. When  
VHS VCR.  
connecting to your PC, refer to the instruction  
manuals of the PC and Setup Guide for the  
provided software.  
1) Slide the battery cover up to remove it, install  
one AA (R6)size battery, then reattach the  
cover.  
When connecting to a Macintosh. . .  
2) Slide the latch to open the compartment door,  
then insert the cassette and close the  
compartment door.  
3) Load the cassette adapter into the VCR and  
play the tape back.  
4) Slide the latch and the compartment door opens  
automatically. This may take around 10 seconds.  
Do not attempt to force the adapter open. Then,  
insert your finger in the hole, and push up and  
remove the cassette.  
The optional KEYSPAN USA-19 USB PDA  
Adapter is required.  
Macintosh is a registered trademark of Apple  
Computer, Inc.  
Keyspan is a trademark of InnoSys Inc.  
During tape loading and unloading, do not touch  
the reels for safety and tape protection.  
Tapes recorded in S-VHS or S-VHS ET mode  
cannot be played back on a regular VHS VCR.  
Playback is possible with a VCR equipped with  
the S-VHS or SQPB (S-VHS QUASI PLAYBACK)  
function.  
During special-effect playback (slow motion, still  
frame, etc.), the picture may vibrate or noise bars  
may appear on the screen.  
To record on a VCR using a compact cassette  
and the adapter, cover the adapters recording  
safety hole with adhesive tape.  
Sliding Latch  
Compartment Door  
Recording  
Safety Hole  
Hole  
Reels  
Battery Cover  
16  
INSTRUCTIONS  
Eyepiece  
Refer to this diagram while reading the instructions.  
1
2
3
4
During shooting  
*
(
#
$
)
%
q
^
w
&
5
Keep the lens  
cap attached to  
the camcorder.  
6
7
Cassette  
holder  
e
r t  
8
9 0 !  
@
LCD monitor  
Viewfinder  
o
90°  
y
u
180°  
Turn the gear to  
take up slack.  
Speaker  
p
y
Transmitted beam  
effetive area  
i
180°  
Erase  
protection tab  
(
)
5m 16ft  
30°  
Q
30°  
E
R
Microphone  
Remote control  
(GR-SXM745 only)  
Video light  
T
U
P
a
s
d
f
Y
I
O
W
LCD Monitor/Viewfinder Indications  
During Recording  
During Playback  
1
2 3  
4
5
q w e  
r t y u i  
6
120M I N  
REC SP  
SET  
T
40  
S
ET  
SP  
4
:
:
TBC  
MONOTONE  
1
2 3 4 5  
7
444  
1
N I GHT 10  
x
AT  
^
*
8
0
@
+
02  
&
(
9
!
SVHS REC  
PAUSE  
MWB  
1X  
:
:
5
M I N  
M
0
1 2 3 4  
o
p
1 / 2  
S
)
– – – – – – – – – –  
+
6
BR I GHT  
#
%
$
CONGRATULAT I ONS  
:
:
––––6––––  
+
DEC 25. 01 AM 11 45 18  
VOLUME  
pg. 25 for Warning Indications .  
17  
CAMERA MENU  
MENU SETTINGS  
1 Set the Power Switch @ to “ ”.  
2 Press the MENU Wheel 1 in. The Menu  
Screen appears. Rotate the MENU Wheel 1 to  
select the desired function.  
To go from CAMERA MENU to SYSTEM MENU,  
rotate the MENU Wheel 1 to select 4TO  
SYSTEM MENUand press it. SYSTEM MENU is  
composed of 2 pages. To go to the next page,  
rotate the MENU Wheel 1 to select 4NEXT”  
and press it.  
To return to CAMERA MENU from page 2 of  
SYSTEM MENU, rotate the MENU Wheel 1 to  
select 4TO CAMERA MENUand press it.  
FOCUS  
If correct focus cannot be obtained with AUTO  
FOCUS, set to MANU to use manual focusing.  
appears.  
To focus on a farther subject, rotate the MENU  
Wheel 1 upward. 1appears and blinks.  
To focus on a nearer subject, rotate the MENU  
Wheel 1 downward. 4appears and blinking.  
If the lens is smeared or blurred, accurate  
focusing is not possible.  
When shooting a subject close to the lens, zoom  
out first (pg. 13, Zooming). If zoomed in in  
the auto focus mode, the camcorder could  
automatically zoom out depending on the  
distance between the camcorder and the subject.  
This does not occur with TELE MACRO”  
(pg. 21) in SYSTEM MENU.  
Be sure to focus the lens in the maximum  
telephoto position when you use the Manual  
Focus mode. If you focus in on a certain subject  
in the wide-angle position, sharply focused  
images cannot be obtained when zoomed in  
because the depth-of-field is reduced at longer  
focal lengths.  
CAMERA MENU  
SYSTEM MENU  
TO SYSTEM MENU  
NEXT  
FOCUS  
AUTO  
AUTO  
AUTO  
MAX  
REC MODE  
D. ZOOM  
WI DE  
SP  
50  
EXPOSURE  
M .W. B .  
x
OFF  
ON  
S . LX  
T I TLE  
S
VHS  
TAPE LENGTH  
D I SPLAY  
OSD OUTPUT  
T
30  
DATE / T I ME D I SP .  
RETURN  
FULL  
ON  
RETURN  
3 Press the MENU Wheel 1 in to display the  
Setting Menu and rotate it to select the desired  
setting.  
When the focus level cannot be adjusted any  
farther or closer, “ ” or “ ” will blink.  
4 Press the MENU Wheel 1 in. The Menu  
EXPOSURE  
Screen reappears with the highlight bar on  
Manual exposure adjustment is recommended in  
the following situations:  
When shooting using reverse lighting or when the  
background is too bright.  
4RETURN. Press the MENU Wheel 1 in. The  
normal screen reappears.  
When shooting on a reflective natural background  
such as at the beach or when skiing.  
When the background is overly dark or the  
subject light.  
To brighten the image, rotate the MENU Wheel  
1 downward.  
To darken the image, rotate the MENU Wheel 1  
upward.  
The exposure control level increases/decreases  
(maximum 06).  
18  
M.W.B.  
TITLE  
If the white balance is correct, all other colors will  
be accurately reproduced.  
Allows you to superimpose one of eight preset  
titles in 2 different languages. Change the  
language in TITLE LANG. (pg. 21) in SYSTEM  
MENU.  
$ shows the selected title which remains until  
OFF is selected.  
AUTO  
:White balance is adjusted  
automatically.  
FINE  
CLOUD  
:Outdoors on a sunny day.  
:Outdoors on a cloudy day.  
DATE/TIME DISP.  
HALOGEN :A video light or similar type of  
lighting is used.  
Makes the date/time appear in the camcorder or on  
a connected monitor (set DATE/TIME in SYSTEM  
MENU first pg. 7).  
The selected display will be recorded. If you do  
not want to record the display, select OFF before  
shooting.  
In the AUTO DATE mode, the camcorder records  
the date for about 5 seconds when recording is  
initiated after the date is changed, a cassette is  
loaded, or AUTO DATE is selected. The date is  
replaced after 5 seconds with AUTO DATEbut  
this is not recorded.  
MWB: White balance is set manually. Hold a sheet  
of plain white paper in front of the subject. Adjust  
zoom or position yourself so that the white paper  
fills the screen. If it is difficult to focus on the white  
paper, adjust focus manually (FOCUS in  
CAMERA MENU). Press the MENU Wheel 1 in  
until MWBbegins blinking. When the setting is  
completed, MWBstops blinking.  
Once you adjust white balance manually, the  
setting is retained even if the power is turned off  
or the battery removed.  
White balance cannot be used when the SEPIA”  
or MONOTONEmode (pg. 23, Digital  
Effects) is activated.  
S.LX  
MAX: To record a subject in a darkly lit  
environment, when it is more convenient to shoot  
the subject with a brighter image even if the picture  
becomes slightly coarse.  
NORMAL: To record a subject in a dimly lit  
environment, when it is more convenient to shoot  
with a less coarse picture although the subject  
becomes slightly dark. This setting is suitable for  
measuring sensitivity conforming to EIA-639 (EIA*  
Standard for Low Light Sensitivity Measurement).  
* EIA : Electronic Industries Alliance  
OFF: Allows you to shoot dark scenes with no  
picture brightness adjustment.  
19  
Tapes recorded in S-VHS or S-VHS ET mode can  
be played back not only on this camcorder but  
also on a Super VHS VCR or a VCR equipped  
with the SQPB (S-VHS QUASI PLAYBACK)  
function.  
When tapes recorded in S-VHS or S-VHS ET  
mode are played back on a VCR equipped with  
the SQPB (S-VHS QUASI PLAYBACK)  
function, S-VHS picture quality is not available.  
Tapes recorded in S-VHS ET mode cannot be  
played back on some VCRs, including some  
JVC VCRs.  
Tapes recorded in S-VHS or S-VHS ET mode  
cannot be played back correctly on a normal VHS  
VCR.  
S-VHS ET does not work with S-VHS tapes.  
To avoid on-screen noise, do not perform Still  
Playback or Shuttle Search repeatedly.  
If the picture contains a lot of jitter or noise, use a  
cleaning cassette.  
SYSTEM MENU  
This Menu Screen cannot be accessed while  
recording.  
REC MODE  
Allows you to set the recording mode. EP”  
(Extended Play) is more economical, providing  
three times the recording time.  
If the recording mode is switched during  
recording, the playback picture will be blurred at  
the switching point.  
D. ZOOM  
Zooming is possible from 16X (the optical zoom  
limit), to a maximum of 50X or 600X digital  
magnification.  
When set to OFFonly optical zoom (maximum  
16x magnification) can function.  
WIDE  
When set to ONblack bars will be recorded at the  
top and bottom of the screen to produce a cinema-  
like wide-screeneffect. Not effective with  
Snapshot(pg. 12).  
S-VHS (S-VHS ET)  
ON: With an S-VHS cassette, Sappears and  
the camcorder records in S-VHS.  
With a VHS cassette, S-ETappears and the  
camcorder records with S-VHS picture quality,  
which is called Super VHS ET (Expansion  
Technology). S-VHS REC appears during  
recording.  
OFF: Records in VHS on a VHS or S-VHS  
cassette.  
JVC EHG (Extra High Grade) tapes are  
recommended for superior results.  
Use S-VHS tape for storing recordings for an  
extended period or for recording important  
scenes, as it enables higher-quality recording and  
playback.  
With some tapes, better picture quality may not  
be obtained even with S-VHS ET recording. It is  
recommended that you do test record beforehand  
to make sure whether better results can be  
obtained.  
If the S-VHS ET mode or recording format is  
switched during recording, the playback picture  
will be blurred at the switching point.  
It is recommended that tapes recorded on this  
camcorder be played back on this camcorder.  
20  
TAPE LENGTH  
TELE MACRO  
Allows you to set the tape length depending on the  
tape used: T20=20 minutes, T30=30 minutes,  
T35=35 minutes, T40=40 minutes.  
When set to ON, you can shoot a subject as large  
as possible at a distance of approx. 60 cm  
(23-5/8").  
Tape remaining time 1 is correct only if the  
correct tape length has been selected.  
Depending on the zoom position, the lens may go  
out of focus.  
DISPLAY  
TITLE LANG.  
FULL: Makes all of the indications appear on the  
LCD monitor/viewfinder during playback or  
recording.  
Allows you to select the language (ENGLISH,  
FRENCH, SPANISH or PORTUGUESE) of TITLE  
in CAMERA MENU. After selection, the TITLE  
setting menu (p. 19) appears automatically.  
SIMPLE: Makes the following indications  
disappear from the LCD monitor/viewfinder during  
DATE/TIME  
recording or playback:  
, tape remaining time,  
Allows you to set the current date and time.  
(pg. 7)  
, tape length (pg. 9, 17).  
OSD OUTPUT  
DEMO MODE  
ON: On-screen indications are displayed.  
Demonstrates certain functions automatically.  
OFF: On-screen indications are turned off except  
Date/Time, Instant Title and Warning Indication.  
Available when the Power Switch @ is set to “  
or “ ” and DEMO MODEis set to ON(factory-  
preset). Performing any operation during the  
demonstration stops the demonstration  
temporarily. Set to OFF to stop completely.  
When a tape whose erase protection tab is in the  
position that allows recording is loaded in the  
camcorder, demonstration is not available.  
If you do not detach the Lens Cap, you cannot  
see the actual changes of the Automatic  
Demonstration activated on the LCD monitor or  
viewfinder.  
REC TIME  
You can shoot a series of pictures, each slightly  
different, of the same object for a brief selected  
period of time (Animation). REC MODE should be  
set to SP.  
Select the desired recording time and press the  
Recording Start/Stop Button ! after focusing on  
the subject.  
The remote control can also be used for this  
setting.* (pg. 24, Animation And Time-Lapse)  
Fade- or wipe-in/out cannot be performed.  
This function is canceled when the power is shut  
off or when the cassette is ejected.  
* GR-SXM745 only.  
INT. TIME  
You can record sequentially at preset time spans.  
Leaving the camcorder aimed at a specific subject,  
you can record subtle changes over an extended  
period of time (Time-Lapse). REC MODE should  
be set to SP.  
(Please note that it is necessary to set the REC  
TIME (Animation) in the SYSTEM MENU before  
performing the INT. TIME (Time-Lapse) function.)  
Select the desired interval time and press the  
Recording Start/Stop Button !.  
The remote control can also be used for this  
setting.* (pg. 24, Animation And Time-Lapse)  
Fade- or wipe-in/out cannot be performed.  
This function is canceled when the power is shut  
off or when the cassette is ejected.  
* GR-SXM745 only.  
21  
Fade/Wipe Effects  
Fade- or wipe-in works at recording start, and fade-  
ADVANCED FEATURES  
Night-Alive  
or wipe-out works at recording end.  
Makes dark subjects or areas even brighter than  
they would be under good natural lighting.  
1) Set the Power Switch @ to “ ”.  
2) Press FADE/WIPE ) repeatedly until the  
desired mode appears.  
3) Press the Recording Start/Stop Button ! to  
activate fade-in/out or wipe-in/out.  
1) Set the Power Switch @ to “ ” or “ ”.  
2) Press NIGHT-ALIVE e repeatedly until the  
desired mode appears.  
Pressing and holding the Recording Start/Stop  
Button ! allows you to vary the length for the  
image during fade in/out or wipe in/out.  
To cancel a fade or wipe, press FADE/WIPE )  
repeatedly until OFFappears.  
A NIGHT AUTO: The shutter speed is auto-  
matically adjusted (maximum 1/6 sec.).  
1 NIGHT 10X (only when the Power Switch @  
is set to “ ”): The shutter speed is set to 1/6th of  
a second to provide 10 times the sensitivity.  
FADER: Fades in/out to a black screen.  
2 NIGHT 60X (only when the Power Switch @  
is set to “ ”): The shutter speed is set to 1 second  
to provide 60 times the sensitivity.  
MOSAIC (Fader): Gradually turns/returns the  
picture into/from a mosaic pattern.  
SHUTTER (Wipe): A black screen moves in  
from the top and bottom, closing over the image  
like a shutter, or a new image pushes open the  
black screen vertically from the center.  
To cancel the effect, press NIGHT-ALIVE e  
repeatedly until OFFappears.  
During Night-Alive, the following cannot be  
activated: Picture Stabilizer, Program AE With  
Special Effects, Digital Effectsand S.LXin  
CAMERA MENU (pg. 19).  
Night-Alive does not work when LIGHT OFF/  
AUTO/ON # is set to AUTOor ON(pg. 13,  
Video Light).  
During Night-Alive, it may be difficult to bring the  
camcorder into focus. To prevent this, use of a  
tripod is recommended.  
SLIDE (Wipe): A black screen moves in from  
the left to gradually cover the image, or a new  
image moves in from right to left.  
DOOR (Wipe): Wipes in as the two halves of  
a black screen open to the left and right, revealing  
the scene, or wipes out and the black screen  
reappears from left and right to cover the scene.  
CORNER (Wipe): Wipes in on a black screen  
from the upper right to the lower left corner,  
revealing the scene, or wipes out from lower left to  
upper right, leaving a black screen.  
WINDOW (Wipe): Wipes in on a black screen  
from the center of the screen towards the corners,  
revealing the scene, or wipe out from the corners  
to the center, leaving a black screen.  
22  
Program AE With Special Effects  
Digital Effects  
1) Set the Power Switch @ to “ ”.  
2) Press P.AE q repeatedly until the desired mode  
appears.  
1)Set the Power Switch @ to “ ”.  
2)Press DIGIFECT w repeatedly until the desired  
mode appears.  
To cancel the effect, press P.AE q repeatedly  
To cancel the effect, press DIGIFECT w  
repeatedly until OFFappears.  
This function cannot be activated during Night-  
Alive (pg. 22).  
Picture Stabilizer cannot be activated during the  
CLASSIC FILM, STROBEand VIDEO ECHO”  
mode.  
until OFFappears.  
Only one mode can be engaged at a time.  
In the High Speed Shutteror Sportsmodes,  
picture color may be adversely affected if the  
subject is lit by alternating discharge-type light  
sources such as flourescent or mercury-vapor  
lights.  
SEPIA: Recorded scenes have a brownish tint  
like old photos. Combine this with WIDE in  
SYSTEM MENU for a classic look.  
This function cannot be activated during Night-  
Alive (pg. 22).  
SPORTS: High shutter speed clearly captures  
fast-moving action.  
MONOTONE: Like black and white films, your  
footage is shot in B/W. Combine this with WIDE in  
SYSTEM MENU for a classic look.  
ND : ND EFFECT: A black mist darkens the  
picture, as when an ND filter is used. Helps to  
counter the effects of glare on the subject.  
B. FILTER: Recorded scenes have a bluish  
tint.  
FG : FOG: Makes the picture look misty white, as  
when an external fog filter is attached to the lens.  
Softens the image and gives it a fantasylook.  
This mode cannot be used when the VIDEO  
ECHOmode (Digital Effects) is activated.  
R. FILTER: Recorded scenes have a reddish  
tint.  
SOLARI: The picture is recorded with an effect  
similar to a painting.  
NEGA POSI: The colors of a picture are  
reversed.  
TWILIGHT: Dusk, twilight scenery, fireworks,  
etc., look more natural and dramatic. In this mode,  
S.LX and AUTO FOCUS in CAMERA MENU  
(pg. 18, 19) may not work.  
MOSAIC: Turns recorded scenes into a mosaic  
pattern.  
STRETCH: Doubles the width of the picture  
horizontally.  
S1/2000 (1/2000 sec. High Speed Shutter):  
Captures faster action than Sports mode. The  
screen becomes slightly dark. Use in well-lit  
situations.  
CLASSIC FILM: Makes your footage look like  
a classic movie by shooting in black and white,  
with a strobing effect, and black bars added at the  
top and bottom.  
STROBE: Your recording looks like a series of  
consecutive snapshots.  
VIDEO ECHO: Adds a ghostto the subject,  
giving your recording a fantasyfeeling. Zoom  
magnification of over 10X is not available.  
23  
USING THE REMOTE CONTROL UNIT (GR-SXM745 only)  
Make sure the remote control is pointed at the remote sensor p.  
5)To begin Insert Editing, press START/STOP P.  
Playback Zoom  
When the counter reaches 0:00:00, editing  
stops automatically and the camcorder enters  
the Insert-Pause mode. To end Insert Editing,  
press STOP U.  
To magnify the recorded image up to 10X at any  
time during playback. Make sure that the TBC  
mode is activated.  
1)Press PLAY T to find the scene of interest.  
2)Press ZOOM (T/W) R. Pressing T zooms in. To  
end zoom press and hold W until magnification  
returns to normal. Or, press STOP U and then  
press PLAY T.  
During Insert Editing, the original audio will be  
heard from the speaker.  
After step 4), Retake(pg. 13) can be  
performed.  
The tape may stop slightly before or after the  
designated end point, and noise bars may appear.  
Neither indicates a defect in the unit.  
Due to digital image processing, the quality of the  
image may suffer.  
Animation And Time-Lapse  
Audio Dubbing  
You can record a new soundtrack on a  
prerecorded tape (normal audio only). The sound  
is recorded from the built-in microphone.  
The remote control lets you set/release interval  
time and recording time without setting REC TIME/  
INT. TIME (pg. 21) in SYSTEM MENU.  
Animation  
Perform steps 1) and 2) of the Insert Editing  
procedure.  
Each time ANIM. O is pressed, the recording time  
changes in the following order: 1/4S, 1/2S, 1S, 5S  
and no indication (off).  
3)Press REW Y to go a little beyond the beginning  
of the scene onto which you want to dub the new  
audio, press PLAY T to view the recorded tape,  
then press PAUSE s at exactly the point where  
dubbing should start.  
4)While holding down A. DUB d, press and  
release PAUSE s.  
5)To begin Audio Dubbing, press PLAY T. When  
the counter reaches 0:00:00, Audio Dubbing  
stops automatically and the camcorder enters  
the Audio Dub-Standby mode. To end Audio  
Dubbing, press STOP U.  
Do not press REW Y or FF a during Audio Dub-  
Standby, or the edit points will not be accurate.  
If the microphone is too close to the TV, or if the  
TVs volume is too high, whistling or howling may  
occur.  
Time-Lapse  
Each time REC TIME O is pressed, the recording  
time changes in the following order: 1/4S, 1/2S,  
1S, 5S and no indication (off). Each time INT. TIME  
f is pressed, the interval time changes in the  
following order: 15S, 30S, 1MIN, 5MIN and no  
indication (off).  
Insert Editing  
You can record a new scene onto a previously  
recorded tape. Only the video signal is recorded in  
this mode.  
1)Set the Power Switch @ to “  
.  
2)Play back the tape, locate the edit-out point and  
press PAUSE s.Press and hold COUNTER R/M  
) for more than 1 second to reset the tape  
counter, then press it again for less than  
1 second so that Mappears.  
For Insert Editing/Audio Dubbing  
Insert Editing and Audio Dubbing may not work  
correctly if the tape contains blank segments, or if  
the recording speed was changed during the  
original recording.  
To edit/dub onto a tape, make sure the erase  
protection tab is in the position that allows  
recording.  
Do not press STOP U during Insert Editing or  
Audio Dubbing, or the edit points will not be  
accurate.  
3)Press REW Y to go a little beyond the beginning  
of the scene you want to replace, press PLAY T  
to view the recorded tape, and press PAUSE s  
exactly at the edit-in point where the new scene  
should start.  
4)While holding down INSERT I, press and  
release PAUSE s. w appears.  
24  
TROUBLESHOOTING  
Before consulting your JVC dealer, please check the following to see if you can correct the problem yourself.  
Vertical white lines appear when shooting a very  
bright object.  
This sometimes occurs when the contrast between the  
back-ground and the object is great. It is not a defect of  
the camcorder.  
Playback picture is blurred or interrupted.  
The video heads are dirty or worn out. Consult your  
nearest JVC dealer for head cleaning or replacement.  
The tape stops during fast-forward or rewind.  
The Counter Memory Function has been activated  
(pg. 14, Counter Memory).  
Bright, crystal-shaped spots appear in the LCD  
monitor and the viewfinder.  
Sunlight is directly entering the lens. This is not a defect  
of the camcorder.  
The date and time displays disappear.  
If you remove the power source from the camcorder  
while the power is on, all settings and selections are  
erased. Make sure to turn the camcorders power off  
before disconnecting the power source.  
Colored bright spots appear all over the LCD monitor  
or the viewfinder.  
The LCD monitor and the viewfinder are made with high-  
precision technology. However, black spots or bright  
spots of light (red, green or blue) may appear constantly  
on the LCD monitor or in the viewfinder. These spots are  
not recorded on the tape. This is not due to any defect of  
the unit. (Effective dots: more than 99.99 %.)  
The tape will not eject.  
The battery pack is running low.  
If the LCD monitor is not open over 60 degrees, the  
EJECT switch t does not function.  
The camcorder is a microcomputer-controlled device.  
External noise and interference (from a TV, a radio,  
etc.) might prevent it from functioning properly. In such  
cases, first disconnect its power supply unit (battery  
pack, AC Adapter, etc.); and then re-connect it and  
proceed as usual from the beginning.  
Animation or Time-Lapse is not available.  
Before recording in the Animation mode at the very  
beginning of a tape, set the camcorder to the Recording  
mode for about 5 seconds, so that the tape runs  
smoothly. Using the Fade-in function at this point is a  
good way to begin an animated program  
(pg. 21, REC TIME/INT. TIME in SYSTEM MENU).  
The tape is running, but there is no playback picture.  
The TV has not been set to its VIDEO mode or channel.  
If A/V connection is used, the TVs VIDEO/TV Switch  
has not been set to VIDEO.  
Warning Indications  
(high)  
(exhausted) : Displays the battery remaining power level. As the battery power comes  
blinks (battery power warning). When the battery power is exhausted, power  
close to nil, the battery indicator  
turns off automatically.  
:Blinks when no cassette is loaded, or when the erase protection tab is not in the position that allows recording.  
TAPE END: Appears when the tape ends during recording, playback or fast-forward.  
LENS CAP: Appears for 5 seconds after power is turned on if the lens cap is attached.  
CONDENSATION OPERATION PAUSED PLEASE WAIT: These 2 warnings appear alternately every 3 seconds  
if condensation occurs. In this case, all functions except tape eject and power on/off are disabled. Remove the tape,  
turn the unit off (without removing the power supply), wait a few minutes for the warnings to clear, and turn it on again.  
HEAD CLEANING REQUIRED USE CLEANING CASSETTE: These 2 warnings appear alternately every 3  
seconds if dirt is detected on the heads during recording. In this case, use an optional cleaning cassette. If the  
warning remains after cleaning, consult your nearest JVC dealer.  
E01E06 UNIT IN SAFEGUARD MODE REMOVE AND REATTACH BATTERY: The error indications (E01 E06)  
show what type of malfunction has occured. If an error indication and warning appear, turn the unit off, remove the  
power supply (battery, etc.) and wait a few minutes for them to clear. When it does, you can resume using the  
camcorder. If the indication remains, consult your nearest JVC dealer.  
25  
CAUTIONS  
When using the AC Adapter in areas other than the USA  
.... avoid prolonged uncharged storage.  
The provided AC Adapter features automatic voltage selection in  
.... remove from charger or powered unit when not in use, as  
some machines use current even when switched off.  
It is normal for the battery pack to be warm after charging, or  
after use.  
the AC range from 110 V to 240 V.  
USING HOUSEHOLD AC PLUG ADAPTER  
In case of connecting the units AC Adapter to an AC wall outlet  
other than American National Standard C73 series type use an AC  
plug adapter, called a Siemens Plug, as shown.  
Temperature Range Specifications  
Charging ................... 10°C to 35°C (50°F to 95°F)  
Operation .................. 0°C to 40°C (32°F to 104°F)  
Storage ..................... 10°C to 30°C (14°F to 86°F)  
Recharging time is based on room temperature of 20°C (68°F).  
The lower the temperature, the longer recharging takes.  
For this AC plug adapter, consult your nearest JVC dealer.  
Plug adapter  
Cassettes  
To properly use and store your cassettes, be sure to read the  
following cautions:  
Video Light  
1. During use . . .  
DANGER:  
.... make sure the cassette bears the S-VHS-C or VHS-C mark.  
.... be aware that recording onto prerecorded tapes automatically  
erases the previously recorded video and audio signals.  
.... make sure the cassette is positioned properly when inserting.  
.... do not load and unload the cassette  
repeatedly without allowing the tape to run at all. This slackens  
the tape and can result in damage.  
The video light becomes extremely hot. Do not  
touch it either while in operation or soon after  
turning it off, otherwise serious injury may result.  
Do not place the camcorder into the carrying  
case immediately after using the video light,  
since it remains extremely hot for some time.  
When operating, keep a distance of about 30 cm (11-13/16)  
between the video light and people or object.  
.... do not open the front tape cover. This exposes the tape to  
fingerprints and dust.  
Do not use near flammable or explosive materials.  
It is recommended that you consult your nearest JVC dealer for  
replacing the video light.  
2. Store cassettes . . .  
.... away from heaters or other heat sources.  
.... out of direct sunlight.  
.... where they wont be subject to unnecessary shock or vibration.  
.... where they wont be exposed to strong magnetic fields (such  
as those generated by motors, transformers or magnets).  
.... vertically, in their original cases.  
General Battery Precautions  
If the remote control or cassette adapter is not functioning even if it  
is being operated correctly, the batteries are exhausted. Replace  
them with fresh ones.  
Main Unit  
Use only the specified batteries pg. 2 PROVIDED  
ACCESSORIES”  
1. For safety, DO NOT . . .  
.... open the camcorders chassis.  
Please make note of the following rules for battery use. When  
misused, the batteries can leak or explode.  
.... disassemble or modify the unit.  
.... short-circuit the terminals of the battery pack. Keep it away  
from metallic objects when not in use.  
1. When replacing batteries, refer to page 2 for the remote control,  
or read the cassette adapter (C-P6U/C-P7U) instructions.  
.... allow inflammables, water or metallic objects to enter the unit.  
.... remove the battery pack or disconnect the power supply while  
the power is on.  
2. Do not use any different size of batteries from those specified.  
3. Be sure to install batteries in the correct direction.  
4. Do not use rechargeable batteries.  
.... leave the battery pack attached when the camcorder is not in use.  
2. Avoid using the unit . . .  
.... in places subject to excessive humidity or dust.  
.... in places subject to soot or steam such as near a cooking stove.  
.... in places subject to excessive shock or vibration.  
.... near a television set.  
5. Do not expose the batteries to excessive heat as they can leak  
or explode.  
6. Do not dispose of the batteries in a fire.  
.... near appliances generating strong magnetic or electric fields  
(speakers, broadcasting antennas, etc.).  
.... in places subject to extremely high (over 40°C or 104°F)  
extremely low (under 0°C or 32°F) temperatures.  
7. Remove the batteries from the unit if it is to be stored for an  
extended period to avoid battery leakage which can cause  
malfunctions.  
Battery Packs  
3. DO NOT leave the unit . . .  
.... in places of over 50°C (122°F).  
.... in places where humidity is extremely low (below 35%) or  
extremely high (above 80%).  
The battery packs are nickel-cadmium or nickel  
metal-hydride batteries. Before using the supplied  
battery pack or an optional battery pack, be sure  
to read the following cautions:  
.... in direct sunlight.  
.... in a closed car in summer.  
.... near a heater.  
.... in dusty places such as a beach.  
1. To avoid hazard . . .  
.... do not burn.  
.... do not short-circuit the terminals.  
.... do not modify or disassemble.  
.... use only specified chargers.  
4. To protect the unit, DO NOT . . .  
.... allow it to become wet.  
.... drop the unit or strike it against hard objects.  
.... subject it to shock or excessive vibration during transportation.  
.... keep the lens directed at extremely bright objects for long  
periods.  
.... direct the eyepiece of the viewfinder at the sun.  
.... carry it by holding the viewfinder or the LCD monitor*. Be sure  
to hold the main unit with both hands or use the grip.  
Terminals  
2. To prevent damage and prolong service  
life . . .  
.... do not subject to unnecessary shock.  
.... avoid repeated charging without fully discharging.  
.... charge in an environment where temperatures are within the  
tolerances shown in the chart below. This is a chemical  
reaction type batterycooler temperatures impede chemical  
reaction, while warmer temperatures can prevent complete  
charging.  
* Applicable models only.  
.... swing it excessively when using the shoulder strap.  
.... store in a cool, dry place. Extended exposure to high  
temperatures will increase natural discharge and shorten  
service life.  
26  
Avoid using strong cleaning agents such as benzine or alcohol.  
Cleaning should be done only after the battery pack has been  
removed or other power units have been disconnected.  
Mold may form if the lens is left dirty.  
When using a cleaner or chemically treated cloth, refer to the  
cautions that came with it.  
LCD Monitor  
1. To prevent damage to the LCD monitor,  
DO NOT . . .  
.... push it strongly or apply any shocks.  
.... place the camcorder with the LCD monitor on the bottom.  
2. To prolong service life . . .  
.... avoid rubbing it with coarse cloth.  
When removing the eyepiece, be sure to hold the viewfinder  
securely.  
3. Be aware of the following phenomena for LCD monitor use.  
These are not malfunctions:  
While using the camcorder, the surface around the LCD monitor  
and/or the back of the LCD monitor may heat up.  
If you leave power on for a long time, the surface around the LCD  
monitor becomes hot.  
Declaration of Conformity  
Model Number  
Trade Name  
: GR-SXM745U/SXM540U  
: JVC  
: JVC AMERICAS CORP.  
: 1700 Valley Road Wayne, N. J.  
07470  
Responsible party  
Address  
How To Handle a CD-ROM (for applicable  
models)  
Telephone Number  
: 973-3175000  
Take care not to soil or scratch the mirror surface (opposite to the  
printed surface). Do not write anything or put a sticker on either  
the front or back surface. If the CD-ROM gets dirty, gently wipe it  
with a soft cloth outward from the center hole using a circular  
motion.  
Do not use conventional disc cleaners or cleaning spray.  
Do not bend the CD-ROM or touch its mirror surface.  
Do not store your CD-ROM in a dusty, hot or humid environment.  
Keep it away from direct sunlight.  
This device complies with Part 15 of FCC Rules. Operation is  
subject to the following two conditions:  
(1) This device may not cause harmful  
interference, and (2) this device must accept any interference  
received, including interference that may cause undesired  
operation.  
Change or modifications not approved by the party responsible  
for compliance could void the users authority to operate the  
equipment. This equipment has been tested and found to  
comply with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses, and  
can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following  
measures:  
About moisture condensation . . .  
You may have observed that pouring a cold liquid into a glass  
will cause drops of water to form on the glassouter surface.  
This same phenomenon occurs on the head drum of a  
camcorder when it is moved from a cool place to a warm  
place, after heating a cold room, under extremely humid  
conditions or in a place directly subjected to the cool air from  
an air conditioner.  
Moisture on the head drum can cause severe damage to the  
video tape, and can lead to internal damage to the camcorder  
itself.  
Serious malfunctioning  
If malfunctioning occurs, stop using the unit immediately and  
consult your local JVC dealer.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for  
help.  
For Your Maintenance  
1. After Use  
1 Set the Power Switch to OFFto turn off the camcorder.  
2 Open the LCD monitor to an angle of over 60 degrees. Slide  
EJECT to open the cassette holder, then remove the  
cassette.  
This Class B digital apparatus complies with Canadian  
ICES-003.  
3 Close and lock the cassette holder by pressing the Close  
button.  
Cet appareil numérique de la classe B est conforme à la  
norme NMB-003 du Canada.  
4 Close and lock the LCD monitor.  
5 Slide BATTERY RELEASE to remove the battery pack.  
6 Attach the provided lens cap to the camcorders lens.  
2. Cleaning The Camcorder  
1 Wipe gently the exterior with a soft cloth. Put cloth in diluted  
mild soap and wring it well to wipe off heavy dirt, then wipe  
again with a dry cloth.  
2 Open the LCD monitor and wipe it gently with a soft cloth. Be  
careful not to damage the monitor. Close the LCD monitor.  
3 Blow the lens with a blower brush, then wipe it gently with  
lens cleaning paper.  
4 Turn the eyepiece counterclockwise and pull it out.  
5 Remove dust from the viewfinder using a blower brush.  
6 Re-attach the eyepiece and turn it clockwise.  
27  
SPECIFICATIONS  
LCD monitor  
: 3.5" diagonally measured, LCD  
panel/TFT active matrix system  
(GR-SXM745 only)  
Camcorder  
General  
3" diagonally measured, LCD  
panel/TFT active matrix system  
(GR-SXM540 only)  
Format  
Power source  
: S-VHS/VHS NTSC standard  
: DC 11 V  
DC 6 V  
(Using AC Adapter)  
(Using battery pack)  
Speaker  
: Monaural  
Power consumption  
Viewfinder on  
LCD monitor on : 4.5 W  
Video light  
Signal system  
Video recording system  
Luminance  
Color  
: 4.0 W  
Connectors  
Video  
: 1 V (p-p , 75 unbalanced,  
: 3.0 W  
: NTSC-type  
)
analog output (via Video output  
connector)  
: 300 mV (rms), 1 kanalog  
output  
Audio  
: FM recording  
: Converted sub-carrier direct  
recording  
(via Audio output connector)  
Digital  
: ø3.5 mm, 4-pole, mini-head jack  
Conforms to VHS standard  
S-Video  
: Y : 1 V (p-p , 75 , analog  
Cassette  
Tape speed  
SP  
:
/
cassette  
)
output  
C: 0.29 V (p-p , 75 , analog  
)
: 33.35 mm/sec. (1-5/16 ips)  
: 11.12 mm/sec. (7/16 ips)  
output  
EP  
Recording time (max.)  
AC Adapter  
SP  
EP  
: 40 minutes  
: 120 minutes  
(with TC-40 cassette)  
Power requirement  
U.S.A. and Canada: AC 120 V`, 60 Hz  
Other countries : AC 110 V to 240 V`,  
Operating  
temperature  
50 Hz/60 Hz  
: 0°C to 40°C (32°F to 104°F)  
Output  
: DC 11 V  
, 1 A  
Operating humidity : 35% to 80%  
Storage temperature : 20°C to 50°C (4°F to 122°F)  
Optional Accessories  
Weight  
: Approx. 930 g (2.1 lbs)  
(GR-SXM745 only)  
Approx. 910 g (2.0 lbs)  
(GR-SXM540 only)  
Battery Packs BN-V12U, BN-V20U, BN-V400U  
A/V (Audio/Video) Cable  
Compact S-VHS (  
ST-C-40/30/20  
Compact VHS (  
Active Carrying Bag CB-V7U  
) Cassettes  
Dimensions  
(W x H x D)  
: 200 mm x 112 mm x 118 mm  
(7-7/8" x 4-7/16" x 4-11/16")  
(with the LCD monitor closed  
and with the viewfinder fully  
tilted downward)  
) Cassettes TC-40/30/20  
Pickup  
Lens  
: 1/4" format CCD  
Some accessories are not available in some areas.  
Please consult your nearest JVC dealer for details  
on accessories and their availability.  
: F1.6, f = 3.9 mm to 62.4 mm,  
16:1 power zoom lens with auto  
iris and macro control, filter  
diameter 40.5 mm  
Viewfinder  
: Electronic viewfinder with 0.5"  
black/white CRT  
White balance  
adjustment  
: Auto/Manual adjustment  
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject to  
change without notice.  
28  

ATN Laser Range Finder Ranger Eye 800 User Manual
Bose Car Amplifier 1800 VI User Manual
GoPro Black CHDSX401 User Manual
Hamilton Beach Blender Hamilton Beach Single Serve Blender User Manual
Hitachi SD 804 User Manual
HP (Hewlett Packard) HP Monitor LE1901wm User Manual
Integra E5SF1UD User Manual
JVC Camcorder GY HM700 (A) User Manual
JVC CS V6 SERIES CS V6936 User Manual
JVC GR DX35 User Manual