COMPACT VHS CAMCORDER
GR-SXM38U
For Customer Use:
Enter below the Model No. and Serial No. which
is located on the bottom of the camcorder.
Retain this information for future reference.
Model No.
Serial No.
CONTENTS
GETTING STARTED
5 ~ 9
RECORDING/PLAYBACK 9 ~ 10
BASIC FEATURES
MENU SETTINGS
TERMS
10 ~ 12
12 ~ 16
24
AUTOMATIC DEMONSTRATION
Dear Customer,
Thank you for purchasing the JVC Compact
VHS camcorder. Before use, please read
“SAFETY PRECAUTIONS” (੬ pg. 3, 4) to
ensure safe use of this product.
Automatic Demonstration takes
place when “DEMO MODE” is set to
“ON” (factory-preset).
•
•
Available when the Power Switch is set to
” or “ ”.
To cancel Automatic Demonstration, set
“DEMO MODE” to “OFF” (੬ pg. 15).
“
LYT1518-001B
SAFETY PRECAUTIONS
CAUTIONS
•
•
This camcorder is designed to be used with
NTSC-type color television signals. It cannot
be used for playback with a television of a
different standard. However, live recording
and LCD monitor/viewfinder playback are
possible anywhere.
Use the JVC BN-V10U/V12U/V20U/V400U
battery packs and, to recharge them or to
supply power to the camcorder from an AC
outlet, use the provided multi-voltage AC
Adapter.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
(An appropriate conversion adapter may be
necessary to accommodate different
designs of AC outlets in different countries.)
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
NOTES:
•
The rating plate (serial number plate) and
safety caution are on the bottom and/or the
back of the main unit.
•
The rating information and safety caution of
the AC Adapter are on its upper and lower
sides.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSETHIS APPARATUSTO RAIN
OR MOISTURE.
ATTENTION
The product that you have purchased is powered
by rechargeable battery. The battery is
a
recyclable. At the end of its useful life, under
various state and local laws, it may be illegal to
dispose of this battery into the municipal waste
stream. Check with your local solid waste officials
for details in your area for recycling options or
proper disposal.
This product has a fluorescent lamp that
contains a small amount of mercury. Disposal
of these materials may be regulated in your
community due to environmental
considerations.
For disposal or recycling information please
contact your local authorities, or the Electronics
Industries Alliance:
<http://www.eiae.org>
Only cassettes marked
and
can be used with this camcorder.
3
The EPA certified RBRC® Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates
JVC is voluntarily participating in an industry program to collect and recycle these batteries at the end
of their useful life, when taken out of service in the United States. The RBRC® program provides a
convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream,
which may be illegal in your area. Please call 1-800-8-BATTERY™ for information on Ni-Cd battery
recycling and disposal bans/restrictions in your area. JVC’s involvement in this program is part of our
commitment to preserving our environment and conserving our natural resources.
When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
IMPORTANT SAFETY INSTRUCTIONS
1)Read these instructions.
2)Keep these instructions.
3)Heed all warnings.
10)Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
4)Follow all instructions.
5)Do not use this apparatus near water.
6)Clean only with dry cloth.
11) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
7)Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
12)Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
8)Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
9)Only use attachments/accessories specified
by the manufacturer.
4
CONTROLS, CONNECTORS AND INDICATORS
Refer to this diagram while reading the instructions.
Eyepiece
1
3
5
4
2
During
shooting
%
&
~
(
)
6
7
Keep the lens
cap attached to
the camcorder
8
5
Cassette holder
9
" #
$
!
Connector Cover
45°
90°
Viewfinder
180°
,
Turn the gear
to take up
slack
Speaker
+
LCD monitor
Erase
protection tab
.
-
Video Light
Microphone
LCD Monitor/Viewfinder Indications
During Recording During Playback
/
5
9
:; <
>
6 7
!
=
4
8
?
–
120M I N
REC SP
A
S–ET
T
30
S
ET
SP
–
:
:
@
TBC
1
2 3 4 5
AT
V
[
+
02
0
\
^
S–VHS REC
PAUSE
MWB
]
_
1
1X
2
5
M I N
1 / 2S
}
{
–
– – – – – – – – – –
+
3
BR I GHT
CONGRATULAT I ONS
:
:
|
DEC 25. 05 AM 11 45 18
"
a
b
––––– –––––
+
VOLUME
–
੬ pg. 17 for “Warning Indications”
5
1
2
• MENU Wheel [–, +] .............................. ੬ pg. 8
• BRIGHT Wheel [–, +] ......................... ੬ pg. 15
• Speaker Volume Control [VOL.] ......... ੬ pg. 10
• TRACKING Wheel [–, +]..................... ੬ pg. 10
5- Second Recording Button
>
?
Tape Length Indicator ........................... ੬ pg. 15
Zoom Indicator Bar ............................... ੬ pg. 10
a Zoom Level Indicator
b Approximate Zoom Ratio
@
[
\
]
^
_
Recording Indicator................................. ੬ pg. 9
Digital Effect Indicator ........................... ੬ pg. 13
Program AE Indicator............................ ੬ pg. 13
Fade/Wipe-Standby Indicator................ ੬ pg. 13
Picture Stabilizer Indicator .................... ੬ pg. 14
• Interval Time/Recording Time Indicator .. ੬ pg. 15
• 5 Sec. Rec Mode Indicator.................. ੬ pg. 10
Instant Title Display............................... ੬ pg. 14
Date/Time Display................................. ੬ pg. 15
Bright Level Indicator ............................ ੬ pg. 15
Focus Indicator...................................... ੬ pg. 10
Exposure Control Level Counter........... ੬ pg. 13
White Balance Mode Indicator.............. ੬ pg. 14
S-VHS/S-VHS ET Recording Indicator..... ੬ pg. 16
Record-Standby Mode Indicator ............. ੬ pg. 9
[5 SEC. REC]...................................... ੬ pg. 10
Power Zoom Lever [T/W]...................... ੬ pg. 10
3
4
• Manual Focus Button [
FOCUS].... ੬ pg. 10
• Time Base Corrector Button [TBC]..... ੬ pg. 11
Shoulder Strap Eyelets........................... ੬ pg. 9
S-Video Output Connector [S].............. ੬ pg. 11
Audio Output Connector [A].................. ੬ pg. 11
Video Output Connector [V] ................. ੬ pg. 11
Battery Release Switch
[BATTERY RELEASE]............................ ੬ pg. 7
DC IN Connector.................................... ੬ pg. 7
• Recording Start/Stop Button ................ ੬ pg. 9
• REFRESH Button................................. ੬ pg. 7
Lock Button............................................. ੬ pg. 8
5
6
7
8
9
{
|
}
V
0
1
2
3
4
5
6
7
8
9
!
"
#
: Cassette Indicator....................... ੬ pg. 15
TBC Indicator........................................ ੬ pg. 11
Recording Format Indicator (S/S-ET)........ ੬ pg. 15
Tape Counter ........................................ ੬ pg. 16
Recording Mode Indicator (SP/EP)....... ੬ pg. 14
Tape Running Indicator
3: Playback
¡: Fast-Forward/ Shuttle Search
1: Rewind/ Shuttle Search
8: Pause
$
%
&
Power Switch [PLAY, OFF,
,
].... ੬ pg. 7, 8, 9
POWER/CHARGE Lamp........................ ੬ pg. 7
• Retake Forward Button [RETAKE F] .. ੬ pg. 10
• Fast-Forward Button [F]........................ ੬ pg. 9
• Play/ Pause Button............................... ੬ pg. 9
• Backlight Compensation Button......... ੬ pg. 10
• Stop Button [STOP].............................. ੬ pg. 9
• Eject [EJECT] Button ........................... ੬ pg. 9
• Retake Rewind Button [RETAKE R]... ੬ pg. 10
(
)
~
• Quick Review Button [
R].............. ੬ pg. 10
!
"
Tracking Indicator.................................. ੬ pg. 10
VOLUME: Speaker Volume Indicator......... ੬ pg. 10
• Rewind Button [R] ................................ ੬ pg. 9
Close Button........................................... ੬ pg. 9
Diopter Adjustment Control .................... ੬ pg. 8
Grip Strap............................................... ੬ pg. 8
Tripod Mounting Socket.......................... ੬ pg. 9
Tape Remaining Time........................... ੬ pg. 15
Recording Mode Indicator .................... ੬ pg. 14
Video Light Indicator............................. ੬ pg. 13
Backlight Compensation Indicator........ ੬ pg. 10
Recording Format Indicator (S/ S-ET)....... ੬ pg. 16
+
,
-
.
/
:
;
<
=
6
Using the Battery Pack
GETTING STARTED
Hook on
Perform step 1) of “Charging the Battery Pack”.
Approximate recording time (unit: min.)
Battery Pack Viewfinder on LCD monitor on
BN-V10U
95
(50)
80
(45)
Push in
BN-V12U
(optional)
100
(55)
85
(50)
Power Switch
BN-V20U
(optional)
160
(85)
140
(80)
BATTERYRELEASE
Switch
BN-V400U
(optional)
380
(210)
330
(195)
Battery pack
To AC outlet
AC Adapter
(
): When the video light is on.
Using AC Power
To DC IN
connector
Connect the AC Adapter to the camcorder
(੬ step 2) of “Charging the Battery Pack”).
•
The provided AC Adapter features automatic
voltage selection in the AC range from 110V
to 240V.
Charging the Battery Pack
ATTENTION:
1) Hook the end of the battery pack to the
camcorder and push the battery in until it locks
in place.
Before detaching the power source, make sure
that the camcorder’s power is turned off.
Failure to do so can cause the camcorder to
malfunction.
•
If the battery pack is attached wrongly, a
malfunction may occur.
2) Set the Power Switch
$
to “OFF” while
. Connect
REFRESH:
pressing down the Lock Button
the AC Adapter to the DC IN connector
then plug the AC Adapter to the AC Outlet.
3) The CHARGE lamp
charging.
#
Be sure to fully discharge a battery pack before
recharging or storing it for a long period of time,
otherwise the battery performance will be
reduced.
!,
%
blinks to indicate
1) Perform steps 1) through 3) of “Charging the
Battery Pack”.
4) When the CHARGE lamp
%
stops blinking
and turns off, charging is finished. Unplug the
AC Adapter from the AC outlet. Disconnect the
AC Adapter from the camcorder.
2) Press REFRESH " for over 4 seconds.The
CHARGE lamp % blinks faster to indicate
discharging.
To Detach The Battery Pack…
3) When discharging is finished, charging
automatically starts and the CHARGE lamp
% blinks normally.
… slide BATTERY RELEASE
9
and pull out the
battery pack.
Battery Pack
Charging time
BN-V10U
approx. 1 hr. 30 min.
approx. 1 hr. 40 min.
approx. 2 hrs. 40 min.
approx. 5 hrs. 10 min.
BN-V12U (optional)
BN-V20U (optional)
BN-V400U (optional)
Charging time is for a fully discharged battery pack.
7
STORE BATTERY:
7) Press the MENU Wheel
1
in to select “3EXIT”
Be sure to fully discharge a battery pack by performing the
following steps before storing it for a long period af time,
otherwise the battery performance will be reduced.
1) Attach the battery to the camcorder with no cassette
inserted.
to close the Menu Screen.
•
•
To display the date and time in the
camcorder’s display and on a connected TV,
see DATE/TIME DISP. (੬ pg. 15) in
SYSTEM MENU.
The date/time cannot be stored in memory if
the built-in clock battery runs out. Consult an
authorised JVC dealer for replacement, or
set the date/time as necessary before you
start shooting.
2) Set the Power Switch
$
#.
to “ ” or “ ” while pressing
down the Lock Button
•
•
•
During charging or discharging, the camcorder cannot
be operated.
Charging and discharging are not possible if the wrong
type of battery is used.
12-hour
indicationwith
AM or PM
When charging the battery pack for the first time or after
a long storage period, the CHARGE lamp % may not
light. Remove the battery pack from the camcorder,
then try charging again.
D A T E
T
I M E SE T
Y E A R
MO N T H
D A Y
2 0 0
6
6
2 8
2 0
T
I M E
PM
8
:
•
•
If
a
fully-charged battery’s operation time remains
extremely short, the battery is worn out. Please
purchase a new one.
R E TURN
Perform charging where the temperature is between
10°C and 35°C (50°F and 95°F). 20°C to 25°C (68°F to
77°F) is the ideal temperature range. If the environment
is too cold, charging may be incomplete.
Grip Adjustment
1) Separate the Velcro strip.
2) Pass your right hand through the loop and grasp the
grip.
3) Adjust so that your thumb and fingers can easily
operate the Recording Start/Stop Button
•
•
Charging time varies according to the ambient
temperature and the status of the battery pack.
Since the AC Adapter processes electricity internally, it
becomes warm during use. Be sure to use it only in
well-ventilated areas.
"
and
•
•
The following operation stops charging or discharging:
Power Zoom Lever
3. Refasten the Velcro strip.
•
•
•
Set the Power Switch $ to “PLAY”, “ ” or “ ”.
3
Disconnect AC Adapter from the AC outlet.
Detach the battery from the camcorder
.
Using the optional AA-V15 AC Power Adapter/Charger,
you can charge the BN-V10U/V12U/V20U/V400U
battery pack without the camcorder.
"
Velcro
strip
However, it cannot be used as an AC adapter.
To avoid interference with reception, do not use the AC
Adapter near a radio.
Recording time is reduced significantly when Zoom or
Record-Standby mode is engaged repeatedly or the
LCD monitor is used repeatedly.
Before extended use, it is recommended that you
prepare enough battery packs to cover
planned shooting time.
•
•
Viewfinder Adjustment
1) Set the Power Switch
$
to
“
#
”
or
“
”
while
•
pressing down the Lock Button
.
3
times the
2) Make sure the LCD monitor is closed and locked.
Pull up the viewfinder and adjust it manually to get
the best view.
3) Turn the Diopter Adjustment Control
indications in the viewfinder are clearly focused.
Date/Time Settings
,
until the
1) Set the Power Switch
down the Lock Button
2) Press the MENU Wheel
Screen appears.
$
to “ ” while pressing
#
.
1
in. The TOP MENU
45°
3) Rotate the MENU Wheel
1
to select “3TO
SYSTEM MENU” and press it.
4) Rotate the MENU Wheel
1
to select “3DATE/
TIME SET” and press it. The DATE/TIME SET
Menu appears.
,
5) To set “YEAR”, “MONTH”, “DAY” or “TIME” (hour/
minute), rotate the MENU Wheel
1
to select the
desired item, and press it. When the setting
begins blinking, rotate the MENU Wheel
1
until
PAUSE
the correct setting appears and then press it. The
setting stops blinking.
6) When none of these settings (“YEAR”, “MONTH”,
“DAY”, “TIME”) blinks, rotate the MENU Wheel
1
to select “3RETURN” and press it, to go to Menu
Screen.
8
Shoulder Strap Attachment
Cassette holder
Thread the strap through the eyelet
5, then fold it
back and thread it through the buckle. Repeat the
procedure to attach the other end of the strap to the
)
other eyelet
5, making sure the strap is not twisted.
Adjust the length.
90°
180°
5
+
Erase protection tab
RECORDING
Set REC MODE, S-VHS (S-VHS ET), TAPE LENGTH and
DATE/TIME. (੬ pg. 12 – 16, “MENU SETTINGS”)
1) Remove the lens cap. Set the Power Switch
or “ ” while pressing down the Lock Button
Shooting while using the viewfinder: Make sure the
LCD monitor is closed and locked.
$
#.
to “
”
Tripod Mounting
Align the screw and camera direction stud on the
tripod with the tripod mounting socket
tighten the screw.
.
.. Then
Shooting while using the LCD monitor: Make sure the
LCD monitor is fully open.
The camcorder is in Record-Standby mode and “PAUSE”
3
•
is displayed.
The viewfinder and LCD monitor cannot be used
simultaneously. Therefore, when opening the LCD
monitor and tilting it upward to 180°, you cannot view
any image in the viewfinder. However, you can shoot
yourself while viewing your own image on the LCD
monitor.
2) Press the Recording Start/Stop Button
"
.
@
appears while recording is in progress.
CAUTION:
When using a tripod, be sure to extend its legs fully to stabilize
the camcorder. To prevent damage to the unit caused by falling
over, do not use a small tripod.
•
To stop recording, press the Recording
Start/Stop Button ". The camcorder re-
enters Record-Standby mode.
To Adjust The Brightness Of The LCD Monitor:
When the Power Switch is set to “ ”, adjust “LCD
BRIGHT” in SYSTEM MENU (੬ pg. 15).
When the Power Switch is set to “ ” or “OFF”, this
adjustment cannot be performed.
Loading/Unloading A Cassette
$
1) Open the LCD monitor fully and keep it
aligned vertically with the camera (do not tilt
it). Press EJECT ) for more than 2 seconds
until the cassette holder opens. Do not force
open.
2) When inserting a cassette, make sure the
label is facing outward.
3) Press the Close button + to close the
cassette holder until it locks in place. Close
the LCD monitor.
$
PLAYBACK
1) Load a tape (੬ pg. 9, “Loading/Unloading A
Cassette”).
2) Set the Power Switch $ to “PLAY” while
pressing down the Lock Button #. To start
playback, press 3/8 (.
•
Closing the LCD monitor while the cassette
holder is still open may cause damage to the
LCD monitor.
Make sure the erase protection tab is in the
position that allows recording. If not, slide
the tab. Some cassettes have removable
tabs. If the tab has been removed, cover the
hole with adhesive tape.
To stop playback temporarily (Still Playback),
press 3/8 (. To stop playback, press 7 ).
Press 1 ~ to rewind, or ¡ & to fast-
forward.
High-speed picture search (Shuttle Search) is
possible by holding 1 ~ or ¡ & down
during playback.
•
•
The cassette holder cannot be opened while
the camcorder is in record mode or
detached from power source.
For VIDEO RECORDING/VIDEO PLAYBACK
•
The camcorder shuts off automatically after
about 5 minutes in the Record-Standby or
Stop mode.
9
To turn on again, set the Power Switch $ to
4) To cancel the Manual Focus, press
. “ disappears and Auto Focus is
applied.
FOCUS
“OFF”, then to “ ”, “ ” or “PLAY”.
When the Power Switch $ is set to “ ”, “
4
”
V
•
”
or “PLAY”, and the LCD monitor is opened at
an angle of 60 degrees or more, the LCD
monitor switches on and the viewfinder
switches off automatically to save power.
The playback picture can be viewed in the
viewfinder (with the LCD monitor shut), on the
LCD monitor or on a connected TV (੬ pg. 11,
“Connections To A TV/VCR”).
•
When the focus level cannot be adjusted any
farther or closer, “ ” or “ ” will blink.
Zooming
To produce the zoom in/out effect. Digital circuitry
extends the maximum magnification offered by
optical zoom. This system is called Digital Zoom.
•
•
•
•
•
•
Slide the Power Zoom Lever 3 towards “T” to zoom
in, or “W” to zoom out.
To control the speaker volume
", rotate the
The further you slide the Power Zoom Lever 3, the
quicker the zoom action.
MENU Wheel 1 towards “+” to turn up, or
towards “–” to turn down. While shooting,
sound is not heard from the speaker.
Noise bars appear and pictures may become
monochrome or darken during Shuttle Search.
This is normal.
Focusing may become unstable during Zooming. In
this case, set the zoom while in Record–Standby,
lock the focus by using the manual focus, then zoom
in or out in Record mode.
•
•
The zoom level indicator ?-a moves during zoom.
Once the zoom level indicator ?-a reaches the
top, all magnification from that point is through
digital processing.
When using Digital Zoom, the quality of image may
suffer. To deactivate Digital Zoom, set “D.ZOOM” (੬
pg. 14) to “OFF” in CAMERA MENU.
BASIC FEATURES
5Sec. Rec (5-sec. Recording)
To record a scene for 5 seconds, providing quick
scene transitions like those seen on TV.
1) Make sure the recording mode is set to “SP”.
2) During Record–Standby, press 5SEC. REC
2
.
.
Quick Review
To check the end of the last recording.
1) Make sure the camcorder is in Record–
Standby mode.
5S
_
appears and 5Sec. Rec is
reserved.
3) Press the Recording Start/Stop Buttons
"
Recording starts, and after 5 seconds, the
camcorder re-enters Record–Standby mode
automatically.
2) Press
~
and release quickly.
•
Tape is rewound for approx. 1 second and
played back automatically, then pauses in
Record–Standby mode for the next shot.
Distortion may occur at the start of playback.
This is normal.
4) To cancel the 5Sec. Rec. function, press
5SEC. REC
2
again so that
5S
_
•
disappears.
•
Fade/Wipe (੬ pg. 13) cannot be activated
during 5Sec. Rec.
Retake
To re-record certain segments.
1) Make sure the camcorder is in Record–
Standby mode.
Backlight Compensation
To increase the brightness of the subject relative
to the background.
2) Press and hold either RETAKE ¡
&
or 1
~
to reach the start point for new recording.
1) Press BACKLIGHT
is displayed and the subject is brightened.
2) To cancel Backlight Compensation, press
(
during recording. “
”
3) Press the Recording Start/Stop Button
"
to
<
start recording.
•
Noise bars appear and pictures may
BACKLIGHT
(
again. “
”
<
disappears.
become monochrome or darken during
Retake. This is normal.
•
•
Backlight Compensation functions in both
recording modes (“ ” or “ ”).
Tracking
Using BACKLIGHT
(
may brighten the
subject, resulting in a washed out or white
image.
Eliminates noise bars that appear on-screen
during playback. To activate Manual Tracking:
•
BACKLIGHT ( and Manual Exposure mode
(੬ pg. 13) cannot be used simultaneously.
1) Press the TRACKING Wheel
1
for approx. 2
so that the
seconds. “MT”
!
appears.
2) Rotate the TRACKING Wheel
1
Auto/Manual Focus
If correct focus cannot be obtained with Auto
noise bars disappear.
•
To return to Auto Tracking, press the
Focus, use Manual Focus.
TRACKING Wheel 1 for approx. 2 seconds or
1) Set the Power Switch
$
#
to “ ” while pressing
.
set the Power Switch $ to “OFF” and then
down the Lock Button
“PLAY” again. “AT”
!
blinks. When Auto
Tracking finishes, the indication disappears.
When noise bars appear during playback, the
camcorder enters the Auto Tracking mode and
2) Press
3) To focus on a distant subject, rotate the MENU
Wheel upward. “2” appears and blinks. To
focus on a close subject, rotate the MENU
Wheel downward. “3” appears and blinks.
FOCUS
4
. “
”
V
appears.
•
1
“AT”
!
appears.
1
10
•
Manual Tracking may not work with tapes
recorded on other VCRs or camcorders.
Connections To A TV/VCR
1) Make sure all units are turned off.
2) Connect the camcorder to a TV or VCR. If
using both TV and VCR, connect the VCR
output to the TV input.
3) Turn on all units. Set the VCR to its AUX input
mode, and set the TV to its VIDEO mode.
Use the AC Adapter as the power supply.
The S-Video cable connection can improve the
dubbed picture quality. The S-Video cable is
optional. Be sure to use the following cable:
YTU94146A S-Video cable.
Consult the JVC Service Center described on
the sheet included in the package for details on
its availability. Make sure to connect the end
with a core filter to the camcorder. The core
filter reduces interference.
Be sure to lower the TV volume to its minimum
to avoid a sudden burst of sound when the
camcorder is turned on.
If you have a TV or speakers that are not
specially shielded, do not place the speakers
adjacent to the TV as interference will occur in
the camcorder playback picture.
TBC (Time Base Corrector)
Removes jitter from fluctuating video signals to
deliver a stable picture even with old tapes.
To activate/release the TBC mode, press TBC
during playback for more than 1 second. “TBC”
is displayed.
4
5
•
•
•
The “TBC” indicator
5
turns green (grey with a
camcorder equipped with
a
black/white
viewfinder) while TBC is working, and white
while TBC is not operative.
•
•
•
TBC does not work during Still Playback and
Shuttle Search (੬ pg. 9).
It may take a few seconds before TBC actually
starts working.
•
•
The picture may be distorted if the TBC mode
is activated or deactivated at the edit-in/-out
points or when normal playback resumes after
Still Playback or Shuttle Search (੬ pg. 9).
If the playback picture is distorted when TBC is
set to on, turn off TBC.
•
To S-Video
White to Audio
6
Output
7
Output
Yellow toVideo
8
Output
Connector
Cover
S-Video
cable
A/V cable
(Optional)
(Optional)
TV
White to
Audio Input
To S-Video
Input
VCR
Yellow to
Video Input
Tape Dubbing
1) Connect the camcorder and the VCR (੬ pg.
11, “Connections To TV/VCR”). Set the
Power Switch to “PLAY” while pressing
down the Lock Button , turn on the VCR’s
A
$
#
power, and insert the appropriate cassettes in
the camcorder and the VCR.
•
Engage the VCR’s AUX and Record-Pause
modes.
2) Press 3/8
(
to find a spot just before the edit-
in point. Once it is reached, press 3/8
(
again.
11
3) Press 3/8
(
and engage the VCR’s Record
adapter, the tape may become damaged. To
take up slack in the tape, turn the gear 3 in
the direction of the arrow.
mode.
4) Engage the VCR’s Record-Pause mode and
press 3/8
(.
•
•
During tape loading and unloading, do not
•
Repeat steps 2) through 4) for additional
editing, then stop the VCR and camcorder
when finished.
touch the reels
protection.
7
for safety and tape
Tapes recorded in S-VHS or S-VHS ET mode
cannot be played back on a regular VHS VCR.
Playback is possible with a VCR equipped with
the S-VHS function.
During special-effect playback (slow motion,
still frame, etc.), the picture may vibrate or
noise bars may appear on the screen.
Using The Cassette Adapter
Use this to play back an S-VHS-C/VHS-C video
cassette recorded with this camcorder on a
S-VHS-C/VHS VCR.
1) Slide the latch 1 to open the compartment
door, then insert the cassette and close the
compartment door 2.
•
•
If the color shown in the window 4 is green or
red, turn the dial in the direction of
5
MENU SETTINGS
“UNLOADING” so that color changes to blue.
This Menu Screen cannot be accessed while
recording.
2) Turn the dial 5 in the direction of “LOADING”
all the way until it stops.
1) Set the Power Switch
down the Lock Button
$
#
to “ ” while pressing
.
•
The color shown in the window 4 changes
from blue \ red \ green (indicating playback
is possible).
2) Press the MENU Wheel
Screen appears. Rotate the MENU Wheel
1
in. The TOP MENU
3) Load the cassette adapter into the VCR and
1
play the tape back.
to select the desired menu or function and
press it.
•
To record on a VCR using a compact cassette
and the adapter, cover the adapter’s recording
safety hole with Adhesive tape.
T O P M E N U
E X P O S U R E
A U T O
O F F
O F F
O F F
4) To unload the cassette, turn the dial 5 in the
direction of “UNLOADING” all the way until it
stops.
L
P
D
I
.
I
G H T
A E
G I
F
/
E C T
F A D E
W I P E O F F
R E C M O D E
2 T O C A M E R A M E N U
S P
•
The color shown in the window 4 changes
from green \ red \ blue (indicating unloading
is possible).
2 T O S Y S T E M M E N U
2 E X I
T
5) Slide the latch 1 to open the compartment
door, then insert your finger in the hole 6, and
push up and remove the cassette.
•
To go from TOP MENU to CAMERA MENU,
rotate the MENU Wheel 1 to select “3 TO
CAMERA MENU” and press it.
6) Close the compartment door 2.
2 Compartment door
C A M E R A M E N U
S T A B
I
L
I
Z E R O F F
M A X .
S
D
.
.
I
L X
Z O O M
D E
5
0 x
4 Window
W
O F F
T E L E M A C R O O F F
Recording
safety hole
2 M . W .
B
E
E
.
A U T O
2 T
2 T
I
I
T L
T L
5 Dial
S E T U P
2 E X I
T
•
To go from TOP MENU to SYSTEM MENU,
rotate the MENU Wheel 1 to select “3 TO
SYSTEM MENU” and press it. SYSTEM
MENU has 2 pages. To go to the next page,
rotate the MENU Wheel 1 to select “3 TO
SYSTEM MENU 2” and press it.
The protec-
tion sheet is
affixed
1 Latch
3 Gear
S Y S T E M M E N U 1
7 Reels
T A P E L E N G T H T 3
0
D
I
S P L A Y
F U L L
O N
Compact video cassette
O S D O U T P U T
L C D B R I G H T
2 D A T E
/
/
T
T
I
I
M E
D
I
S P .
2 D A T E
M E S E T
2 T O S Y S T E M M E N U
2
2 E X I
T
6 Hole
3) Rotate the Menu Wheel
1
to select the
desired setting and press it.
4) Press “3 EXIT” to exit from any menu.
•
If there is slack in the video tape when
inserting the compact cassette into the
12
TOP MENU
1/2000 (1/2000 sec. High Speed
Shutter):
Captures faster action than Sports mode. The
screen becomes slightly dark. Use in well-lit
environment.
EXPOSURE
Manual exposure adjustment is recommended
in the following situations:
•
When shooting using reverse lighting or
when the background is too bright.
SUNSET: Makes scenes look like
a
sunset with reddish tint.
•
When shooting on
a
reflective natural
background such as at the beach or in the
SURF&SNOW: Compensates for subjects
that may otherwise appear too dark when
shooting in extremely bright surroundings such
as in the snow or beach. In this mode, the fast-
moving images can be recorded since the
shutter speed becomes fast.
snow.
•
When the background is overly dark or the
subject light.
1) Rotate the MENU Wheel
1
to select
“MANUAL”, then press it.
2) To brighten the image, rotate the MENU
•
In the “High Speed Shutter” or “Sports”
modes, picture color may be adversely
affected if the subject is lit by alternating
discharge-type light sources such as
flourescent or mercury-vapour lights.
Wheel 1 downward.
•
To darken the image, rotate the MENU
Wheel 1 upward.
The exposure control level increases/
decreases (maximum 06).
DIGIFECT (Digital Effects)
OFF: To cancel the effect.
LIGHT (LED Light)
To brighten the scene when natural lighting is
SEPIA: Recorded scenes have a brownish
tint like old photos. Combine this with WIDE in
CAMERA MENU for a classic look.
B/W:MONO : Like black and white films, your
footage is shot in B/W. Combine this with WIDE
in CAMERA MENU for a classic look.
B. FILTER: Recorded scenes have a bluish
tint.
too dim.
OFF : Turns off the light.
AUTO: Automatically turns on the light when
the camcorder senses insufficient
lighting on the subject.
ON : Always keeps the light on as long as the
camcorder is turned on.
•
It is recommended to set M.W.B. (੬ pg. 14)
R. FILTER: Recorded scenes have
a
to
in CAMERA MENU when you use
reddish tint.
the LED light.
SOLARI: The picture is recorded with an
effect similar to a painting.
•
The battery pack’s charge may be low even
though the battery indicator (
) does not
blink, the camcorder may turn off
automatically when you turn on the LED
light, or when you start recording with the
LED light turned on.
When the LED Light mode is set to “AUTO”:
Depending on the lighting conditions, the
LED light may keep turning on and off.
NEGAPOSI: The colors of a picture are
reversed.
MOSAIC: Turns recorded scenes into a
mosaic pattern.
STRETCH: Doubles the width of the picture
horizontally.
•
•
While the “Sports” or “High Speed Shutter”
mode is engaged, the light is likely to stay on.
While the “Twilight” mode is engaged, the light
will not activate. (੬ pg. 13, “Program AE with
Special Effects”)
FADE/WIPE
Fade- or wipe-in works when recording begins,
and fade-or wipe-out works when recording
ends.
•
Pressing and holding the Recording Start/
Stop Button " allows you to vary the length
for the image during fade in/out or wipe in/
out.
P. AE (Program AE with special effects)
OFF: To cancel the effect.
SPORTS: High shutter speed clearly
captures fast-moving action.
ND EFFECT: A black mist darkens the picture,
as when an ND filter is used. Helps to counter
the effects of glare on the subject.
OFF: To cancel the effect.
FADER: Fades in/out to a black screen.
W.FADER: Fades in/out to a white screen.
MOSAIC (Fader): Gradually turns/returns
the picture into/from a mosaic pattern.
FOG: Makes the picture look misty white, as
when an external fog filter is attached to the
lens.
SHUTTER (Wipe): A black screen moves
Softens the image and gives it a “fantasy” look.
in from the top and bottom, closing over the
image like a shutter, or a new image pushes
open the black screen vertically from the
center.
TWILIGHT:
Dusk,
twilight
scenery,
fireworks, etc., look more natural and dramatic.
In this mode, the Auto Focus (੬ pg. 10) and
S.LX (੬ pg. 14) may not work.
13
When set to “OFF” only optical zoom
SLIDE (Wipe): A black screen moves in
from the left to gradually cover the image, or a
new image moves in from right to left.
(maximum 25x magnification) can function.
\
WIDE
When set to “ON” black bars will be recorded at
the top and bottom of the screen to produce a
cinema-like “wide-screen” effect.
DOOR (Wipe): Wipes in as the two halves
of a black screen open to the left and right,
revealing the scene, or wipes out and the black
screen reappears from left and right to cover
the scene.
CORNER (Wipe): Wipes in on a black
screen from the upper right to the lower left
corner, revealing the scene, or wipes out from
lower left to upper right, leaving a black screen.
TELE MACRO
When set to “ON”, you can shoot a subject as
large as possible at a distance of approx. 40
cm (16"). Depending on the zoom position, the
lens may go out of focus.
M.W.B.
If the white balance is correct, all other colors
will be accurately reproduced.
WINDOW (Wipe): Wipes in on
a
black
screen from the center of the screen towards
the corners, revealing the scene, or wipe out
from the corners to the center, leaving a black
screen.
AUTO
FINE
:White balance is adjusted
automatically.
:Outdoors on a sunny day.
CLOUD :Outdoors on a cloudy day.
SCROLL (Wipe): Wipes in on
a
black
screen from the bottom to the top, revealing the
scenes, or wipes out from the top to the
bottom, leaving a black screen.
HALOGEN:A video light or similar type of
lighting is used.
MWB: White balance is set manually. Hold a
sheet of plain white paper in front of the
subject. Adjust zoom or position yourself so
that the white paper fills the screen. If it is
difficult to focus on the white paper, adjust
focus manually (੬ pg. 10, “Auto/Manual
Focus”). Press the MENU Wheel 1 in until
“MWB” 1 begins blinking. When the setting is
completed, “MWB” 1 stops blinking.
REC MODE
Allows you to set the recording mode. “EP”
(Extended Play) is more economical, providing
thrice the recording time.
•
If the recording mode is switched, the
playback picture will be blurred at the
switching point.
•
Once you adjust white balance manually, the
setting is retained even if the power is turned
off or the battery is removed.
White balance cannot be used when the
“SEPIA” or “B/W:MONO” mode (੬ pg. 13,
“Digital Effects”) is activated.
CAMERA MENU
STABILIZER
The Picture Stabilizer compensates for
unstable images caused by camera-shake,
particularly at high magnification.
ON: The Picture Stabilizer is activated.
^ appears.
OFF:The Picture Stabilizer is deactivated.
•
TITLE
Allows you to superimpose one of eight preset
titles in
4
different languages. Change the
language in “LANGUAGE” in “TITLE SETUP” in
^ disappears.
CAMERA MENU.
•
•
Accurate stabilization may not be possible in
certain conditions including excessive hand
shake.
•
{ shows the selected title which remains
until “OFF” is selected.
TITLE SETUP
djust the settings for TITLE.
^ appears blinking if the Stabilizer
cannot be used.
A
S.LX
MAX: To record
environment, when it is more convenient to
shoot the subject with a brighter image even if
the picture becomes slightly coarse.
NORMAL: To record a subject in a dimly lit
environment, when it is more convenient to
shoot with a less coarse picture although the
subject becomes slightly dark.
OFF: Allows you to shoot dark scenes with no
picture brightness adjustment.
SIZE
:When “LARGE” is selected, the
title is twice enlarged vertically
than “NORMAL”.
a
subject in
a
darkly lit
SCROLL :When “ON” is selected, the title is
scrolled from right to left.
LANGUAGE:Select the language for TITLE.
To set “SIZE”, “SCROLL” or “LANGUAGE”,
rotate the MENU Wheel
1
to select the
desired item and press it. When the setting
begins blinking, rotate the MENU Wheel 1
until the correct setting appears and then select
it. The setting stops blinking.
D. ZOOM
Zooming is possible from 25X (the optical zoom
limit), to a maximum of 50X or 1000X digital
magnification.
14
SYSTEM MENU
SYSTEM MENU 2
SYSTEM MENU 1
DEMO MODE
Demonstrates certain functions automatically.
TAPE LENGTH
Available when the Power Switch $ is set to
Allows you to set the tape length depending on
the tape used: T20=20 minutes, T30=30
minutes, T35=35 minutes, T40=40 minutes.
Tape remaining time / is correct only if the
correct tape length has been selected.
“
” or “ ” and “DEMO MODE” is set to “ON”
(factory-preset).
•
To cancel demonstration, set “DEMO
MODE” to “OFF”.
Pressing MENU Wheel 1 directly accesses
DEMO MODE menu while the demo is in
progress.
Performing any operation during the
demonstration stops the demonstration
temporarily. If no operation is performed for
•
•
DISPLAY
FULL: Makes all of the indications appear on
the LCD monitor/viewfinder during playback or
recording.
SIMPLE: Makes the following indications
disappear from the LCD monitor/viewfinder
during recording or playback:
remaining time /,
•
more than
1
minute after that, the
demonstration will resume.
•
•
•
“DEMO MODE” remains “ON” even if the
camcorder power is turned off.
4, tape
, tape length >.
When
a
cassette is in the camcorder,
demonstration is not available.
OSD OUTPUT
If you do not detach the Lens Cap, you
cannot see the actual changes of the
Automatic Demonstration activated on the
LCD monitor or viewfinder.
ON: On-screen indications are displayed.
OFF: On-screen indications are turned off
except Date/Time, Instant Title and Warning
Indication.
REC TIME
LCD BRIGHT
You can shoot a series of pictures, each slightly
different, of the same object for a brief selected
period of time (Animation). REC MODE should
be set to “SP”.
Select the desired recording time and press the
Recording Start/Stop Button " after focusing
on the subject.
To adjust the brightness of the LCD monitor,
perform the following steps quickly (within
approx. 1 second by each interval):
1) Select “LCD BRIGHT” in SYSTEM MENU.
The “BRIGHT ON” message appears.
2) Press the BRIGHT Wheel 1 in to return to
normal screen.
•
•
Fade- or wipe-in/out cannot be performed.
This function is cancelled when the power is
turned off or when the cassette is ejected.
To use this function, it is recommended that
SCROLL in TITLE SETUP (੬ pg. 14) be set
to “OFF”.
3) Rotate the BRIGHT Wheel 1 to display the
}
bright level indicator
.
4) Rotate the BRIGHT Wheel
1
until the
•
appropriate brightness is reached. After the
BRIGHT Wheel 1 is released, the indicator
soon disappears and adjustment is
completed.
INT.TIME
You can record sequentially at preset time
spans.
Leaving the camcorder aimed at a specific
subject, you can record subtle changes over an
extended period of time (Time-Lapse). REC
MODE should be set to “SP”.
(Please note that it is necessary to set the REC
TIME (Animation) in the SYSTEM MENU
before performing the INT. TIME (Time-Lapse)
function.)
Select the desired interval time and press the
Recording Start/Stop Button ".
DATE/TIME DISP.
The date/time appears in the camcorder or on
a
connected monitor (set DATE/TIME in
SYSTEM MENU first ੬ pg. 8).
•
•
The selected display will be recorded. If you
do not want to record the display, select
“OFF” before shooting.
In the AUTO DATE mode, the camcorder
records the date for about 5 seconds when
recording is initiated after the date is
changed, a cassette is loaded, or AUTO
DATE is selected. The date is replaced after
5 seconds with “AUTO DATE” but this is not
recorded.
•
•
Fade- or wipe-in/out cannot be performed.
This function is cancelled when the power is
turned off or when the cassette is ejected.
To use this function, it is recommended that
SCROLL in TITLE SETUP (੬ pg. 14) be set
to “OFF”.
•
DATE/TIME SET
Allows you to set the current date and time.
(੬ pg. 8)
15
S-VHS (S-VHS ET)
VCR MENU
ON: With an S-VHS cassette, “S” = appears
and the camcorder records in S-VHS.
With a VHS cassette, “S-ET” = appears and
the camcorder records with S-VHS picture
quality, which is called Super VHS ET
E R
(Expansion Technology). “S-VHS REC”
2
appears during recording.
OFF: Records in VHS on a VHS or S-VHS
cassette.
•
•
JVC EHG (Extra High Grade) tapes are
recommended for superior results.
Use S-VHS tape for storing recordings for an
extended period or for recording important
scenes, as it enables higher-quality
recording and playback.
COUNTER MEMORY
Makes it easier to locate a specific tape segment.
1) Set the Power Switch to “PLAY” while
$
pressing down the Lock Button
#.
•
With some tapes, better picture quality may
not be obtained even with S-VHS ET
recording. It is recommended that you do
test record beforehand to make sure
whether better results can be obtained.
It is recommended that tapes recorded on
this camcorder be played back on this
camcorder.
Tapes recorded in S-VHS or S-VHS ET
mode can be played back not only on this
camcorder but also on a Super VHS VCR.
Tapes recorded in S-VHS ET mode cannot
be played back on some VCRs, including
some JVC VCRs.
Tapes recorded in S-VHS or S-VHS ET
mode cannot be played back correctly on a
normal VHS VCR.
S-VHS ET does not work with S-VHS tapes.
To avoid on-screen noise, do not perform
Still Playback or Shuttle Search repeatedly.
If the picture contains a lot of jitter or noise,
use a cleaning cassette.
2) Press the MENU Wheel
1
in. The VCR MENU
screen appears.
3) Rotate the MENU Wheel
1
to select
“COUNTER MEMORY” and press it. Then,
rotate the MENU Wheel
1
to “ON” and press
•
•
•
•
it. (“M” appears when you return to normal
screen.)
4) Rotate the MENU wheel to select “COUNTER
RESET” and press it. Then, rotate the MENU
Wheel
1
to “YES” and press it. The counter
resets to “0:00:00”.
5) To return to normal screen, rotate the MENU
Wheel
1
to “3EXIT” and press it.
6) After recording or playback, press 7
. The tape automatically stops at or
close to 0:00:00.
7) Press 3/8 to start playback.
), then
1
~
(
•
•
•
The counter memory functions in both Fast-
Forward and Rewind modes.
•
16
TROUBLESHOOTING
Before consulting your JVC dealer, please check the following to see if you can correct the problem
yourself.
Vertical white lines appear when shooting a
very bright object.
The tape is running, but there is no play-
back picture.
•
This sometimes occurs when the contrast
between the background and the object is
great. It is not a defect of the camcorder.
•
The TV has not been set to its VIDEO mode
or channel.
•
If A/V connection is used, the TV’s VIDEO/
TV Switch has not been set to VIDEO.
Bright, crystal-shaped spots appear in the
LCD monitor and the viewfinder.
Playback picture is blurred or interrupted.
•
The video heads are dirty or worn out.
Consult your nearest JVC dealer for head
cleaning or replacement.
•
Sunlight is directly entering the lens. This is
not a defect of the camcorder.
Colored bright spots appear all over the
LCD monitor or the viewfinder.
The tape stops during fast-forwarding or
rewinding.
•
The LCD monitor and the viewfinder are
made with high-precision technology.
However, black spots or bright spots of light
(red, green or blue) may appear constantly
on the LCD monitor or in the viewfinder.
These spots are not recorded on the tape.
This is not due to any defect of the unit.
(Effective dots: more than 99.99%.)
•
The Counter Memory Function has been
activated (੬ pg. 16, “COUNTER MEMORY”).
The date and time displays disappear.
•
If you remove the power source from the
camcorder while the power is on, all settings
and selections are erased. Make sure to turn
the
camcorder’s
power
off
before
Animation or Time-Lapse is not available.
Before recording in the Animation mode at
the very beginning of tape, set the
disconnecting the power source.
•
The tape will not eject.
a
•
•
The battery pack is running low.
camcorder to the Recording mode for about
5 seconds, so that the tape runs smoothly.
Using the Fade-in function at this point is a
good way to begin an animated program (੬
pg. 15, REC TIME/INT. TIME in SYSTEM
MENU).
If the LCD monitor is not open over 60
degrees, the EJECT button ) does not
function.
The camcorder is a microcomputer-controlled device.
External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In
such cases, first disconnect its power supply unit (battery pack, AC Adapter, etc.); and then re-
connect it and proceed as usual from the beginning.
WARNING INDICATIONS:
(high)
(exhausted) : Displays the battery remaining power level. As the battery
power comes close to nil, the battery indicator
blinks (battery power warning). When the battery power is
exhausted, power turns off automatically.
: Blinks when no cassette is loaded, or when the erase protection tab is not in the position that allows
recording.
TAPE END: Appears when the tape ends during recording, playback or fast-forwarding.
LENS CAP: Appears for 5 seconds after power is turned on if the lens cap is attached.
CONDENSATION OPERATION PAUSED PLEASE WAIT: These 2 warnings appear alternately every 3
seconds if condensation occurs. In this case, all functions except tape eject and power on/off are disabled.
Remove the tape, turn the unit off (without removing the power supply), wait a few minutes for the warnings to
clear, and turn it on again.
HEAD CLEANING REQUIRED USE CLEANING CASSETTE: These 2 warnings appear alternately
every 3 seconds if dirt is detected on the heads during recording. In this case, use an optional cleaning
cassette. If the warning remains after cleaning, consult your nearest JVC dealer.
E01—E06 UNIT IN SAFEGUARD MODE REMOVE AND REATTACH BATTERY: The error indications (E01
— E06) show what type of malfunction has occured. If an error indication and warning appear, turn the unit off,
remove the power supply (battery, etc.) and wait a few minutes for them to clear. When it does, you can
resume using the camcorder. If the indication remains, consult your nearest JVC dealer.
17
CAUTIONS
When using the AC Adapter in areas other than the USA
Cassettes
The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
To properly use and store your cassettes:
1) During use…
USING HOUSEHOLD AC PLUG ADAPTER
…
beware that recording onto prerecorded tapes
automatically erases the previously recorded video and
audio signals.
In case of connecting the unit’s AC Adapter to an AC wall outlet
other than American National Standard C73 series type use an
AC plug adapter, called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest JVC dealer.
…
…
make sure the cassette is positioned properly when
inserting.
do not load and unload the cassette repeatedly without
allowing the tape to run at all. This slackens the tape and
can result in damage.
do not open the front tape cover. This exposes the tape to
fingerprints and dust.
Plug adapter
…
•
If there is dust or dirt on the AC Adapter, wipe it clean
before using.
2) Store cassettes…
General Battery Precautions
…
…
away from heaters, other heat sources or direct sunlight.
where they won’t be subject to unnecessary shock or
vibration.
Please make note of the following rules for battery use. When
misused, the batteries can leak or explode.
1) Do not use any different size of batteries from those
specified.
…
where they won’t be exposed to strong magnetic fields
(such as those generated by motors, transformers or
magnets).
2) Be sure to insert batteries in the correct direction.
3) Do not use Generic non-JVC batteries. Using generic non-
JVC batteries can cause serious damage to the camera’s
internal battery charging circuits.
4) Do not expose the batteries to excessive heat as they can
leak or explode.
5) Do not dispose of the batteries in a fire.
6) Remove the batteries from the unit if it is to be stored for an
extended period to avoid battery leakage which can cause
malfunctions.
…
vertically, in their original cases.
Main Unit
1) For safety, DO NOT…
…
…
…
open the camcorder’s chassis.
disassemble or modify the unit.
short-circuit the terminals of the battery pack. Keep it away
from metallic objects when not in use.
allow inflammables, water or metallic objects to enter the unit.
remove the battery pack or disconnect the power supply
while the power is on.
leave the battery pack attached when the camcorder is not
in use.
…
…
Battery Packs
The battery packs are nickel-cadmium or
nickel metal-hydride batteries. Before using
the supplied battery pack or an optional
battery pack, be sure to read the following
cautions:
…
2) Avoid using the unit…
…
in places subject to excessive humidity, dust, shock or
vibration.
1) To avoid hazard…
…
in places subject to soot or steam such as near a cooking
stove.
…
…
…
…
do not burn.
do not short-circuit the terminals.
do not modify or disassemble.
use only specified chargers.
…
…
near a television set.
near appliances generating strong magnetic or electric
fields (speakers, broadcasting antennas, etc.).
in places subject to extremely high (over 40°C or 104°F) or
extremely low (under 0°C or 32°F) temperatures.
Terminals
2) To prevent damage and prolong
…
service life…
…
…
…
do not subject to unnecessary shock.
3) DO NOT leave the unit . . .
avoid repeated charging without fully discharging.
charge in an environment where temperatures are within
the tolerances shown in the chart below. This is a chemical
reaction type battery—cooler temperatures impede
chemical reaction, while warmer temperatures can prevent
complete charging.
…
…
in places of over 50°C (122°F).
in places where humidity is extremely low (below 35%) or
extremely high (above 80%).
in direct sunlight.
…
…
…
…
in a closed car in summer.
near a heater.
in dusty places such as a beach.
…
…
store in
a
cool, dry place. Extended exposure to high
temperatures will increase natural discharge and shorten
service life.
4) To protect the unit, DO NOT…
fully charged and then fully discharged the battery every 6
months when storing it over a long period of time.
remove from charger or powered unit when not in use.
It is normal for the battery pack to be warm after
charging, or after use.
…
…
…
allow it to become wet.
drop the unit or strike it against hard objects.
subject it to shock or excessive vibration during
transportation.
…
•
…
keep the lens directed at extremely bright objects for long
periods.
direct the eyepiece of the viewfinder at the sun.
carry it by holding the viewfinder or the LCD monitor. Be
sure to hold the main unit with both hands or use the grip.
swing it excessively when using the shoulder strap.
•
•
•
•
•
Temperature Range Specifications
Charging 10°C to 35°C (50°F to 95°F)
Operation 0°C to 40°C (32°F to 104°F)
Storage –10°C to 30°C (14°F to 86°F)
Recharging time is based on room temperature of 20°C
(68°F).
…
…
…
•
The lower the temperature, the longer recharging takes.
18
LCD Monitor
3 Blow the lens with a blower brush, then wipe it
1) To prevent damage to the LCD monitor, DO
NOT…
gently with lens cleaning paper.
4 Remove dust from the viewfinder using
a
… push it strongly or apply any shocks.
… place the camcorder with the LCD monitor on the
bottom.
blower brush.
•
•
Avoid using strong cleaning agents such as
benzine or alcohol.
2) To prolong service life…
Cleaning should be done only after the
battery pack has been removed or other
power units have been disconnected.
Mold may form if the lens is left dirty.
When using a cleaner or chemically treated
cloth, refer to the cautions that came with it.
… avoid rubbing it with coarse cloth.
3) Beware of the following phenomena for LCD
monitor use.These are not malfunctions:
•
•
•
While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
•
If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
This device complies with Part 15 of FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.
ForYour Maintenance
1) After Use
1 Turn off the camcorder.
2 Open the LCD monitor to an angle of over 60
degrees.
Press EJECT for approximately 2 seconds to
open the cassette holder, then remove the
cassette.
3 Close and lock the cassette holder by pressing
the Close button.
4 Close and lock the LCD monitor.
5 Slide BATTERY RELEASE to remove the
battery pack.
6 Attach the provided lens cap to the
camcorder’s lens.
Changes or modifications not approved by JVC
could void the user’s authority to operate the
equipment. This equipment has been tested
and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
2) Cleaning The Camcorder
1 Gently wipe the exterior with a soft cloth, with
diluted mild soap, wipe off heavy dirt, then
wipe again with a dry cloth.
2 Wipe the LCD monitor gently with a soft cloth.
Be careful not to damage the monitor. Close
the LCD monitor.
About moisture condensation…
•
You may have observed that pouring a
cold liquid into a glass will cause drops of
water to form on the glass’ outer surface.
This same phenomenon occurs on the
head drum of a camcorder when it is
moved from a cool place to a warm place,
after heating
a
cold room, under
extremely humid conditions or in a place
directly subjected to the cool air from an
air conditioner.
Moisture on the head drum can cause
severe damage to the video tape, and can
lead to internal damage to the camcorder
itself.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/
TV technician for help.
•
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
19
SPECIFICATIONS
Pickup
Lens
:1/6" format CCD
Camcorder
General
Format
:F1.8, f = 2.2 mm to 55 mm,
25:1 power zoom lens with
auto iris and macro control
:ø 30.5 mm
:Electronic viewfinder with
0.16" black/white LCD
:S-VHS/VHS NTSC standard
Power source :DC 11 V
(Using AC
Filter diameter
Adapter)
DC 6 V
pack)
Viewfinder
(Using battery
White balance
adjustment
LCD monitor
Power consumption
Viewfinder on :3.5 W
LCD monitor on :4.3 W
LED light
Maximum
:Auto/Manual adjustment
: 2.50" diagonally measured,
LCD panel/TFT active matrix
system
:0.4 W
: 9.2 W (When charging a battery)
Speaker
:Monaural
Signal system
Video recording system
Luminance
Color
:NTSC-type
Connectors
Video
:1 V (p-p), 75 Ω unbalanced,
analog output (via Video
output connector)
:300 mV (rms), 1 kΩ, analog
output (via Audio output
connector)
:FM recording
:Converted sub-carrier
direct recording
Conforms to VHS standard
Audio
Cassette
Tape speed
SP
:
/
cassette
S-Video
:Y : 1 V (p-p), 75 Ω, analog
:33.35 mm/sec. (1-5/16 ips)
:11.12 mm/sec. (7/16 ips)
output
EP
C : 0.29 V (p-p), 75 Ω,
analog output
Recording time (max.)
SP
EP
:40 minutes
:120 minutes
AC Adapter
Power requirement
(with TC-40 cassette)
Operating
temperature
Operating humidity :35% to 80%
U.S.A and Canada:AC 120 V — 60 V~
Other countries :AC 110 V — 240 V~,
50 Hz/60 Hz
:0°C to 40°C (32°F to 104°F)
Storage temperature : –20°C to 50°C (-4°F to 122°F)
Output
:DC 11 V
, 1 A
Weight
Dimensions
(W x H x D)
:Approx. 774 g (1.71 Ibs.)
:81 mm x 125 mm x 216 mm
(3-1/4" x 4-15/16" x 8-9/16")
(with the LCD monitor closed
and with the viewfinder fully
tilted downward)
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications
subject to change without notice.
20
Uso de La Batería
ESPAÑOL — ALIMENTACIÓN
Efectúe el paso 1) de “Carga de La Batería”.
Enganche.
Tiempo de grabación aproximado (unidad: min)
Batería
Visor
conectado
Monitor LCD
conectado
BN-V10U
95
(50)
80
(45)
Empuje.
Conmutador de
alimentación
BN-V12U
(opcional)
100
(55)
85
(50)
Conmutador BATTERY
RELEASE
BN-V20U
(opcional)
160
(85)
140
(80)
Batería
BN-V400U
(opcional)
380
(210)
330
(195)
A la toma de
corriente alterna
(
): cuando el foco de video está encendido
Al jack de
entrada
de CC
Uso de La Alimentación De Ca
Conecte el adaptador de CA en la cámara de
video (੬ pasos 2) de “Carga de La Batería”).
(DC IN)
Adaptador de CA
•
El adaptador de CA suministrado presenta
una selección automática de voltaje con
límites de CA de 110V a 240V.
Carga de La Bateria
1) Asegúrese de que la batería esté colocada en la
ATENCIÓN:
cámara de video. Enganche el extremo la
a
cámara de video y presione la batería hacia el
interior hasta que quede bloqueada en su lugar.
Si la batería está colocada en la posición
equivocada, puede ocurrir un fallo.
Antes de retirar la fuente de alimentación,
asegúrese que la alimentación de la cámara de
video esté desactivada. De lo contrario puede
ocurrir un fallo en la cámara de video.
•
2) Ajuste el conmutador de alimentación
“OFF” mientras presiona el botón de bloqueo
localizado en el conmutador. Conecte el
adaptador de alimentación CA al jack de
entrada de CC (DC IN)
$
en
REFRESCO:
#
Asegúrese de descargar completamente una
batería antes de recargarla, de lo contrario, el
desempeño de la batería será reducido.
1) Ejecute los pasos de 1) hasta 3) de “Carga de
La Batería”.
!
.
3) Enchufe el adaptador de alimentación CA en
una toma de corriente alterna. La lámpara
indicadora CHARGE
%
de la cámara de video
2) Presione REFRESH
segundos. La lámpara CHARGE
"
durante más de 4
destellará
parpadeará para indicar que la carga se ha
%
iniciado.
para indicar que la descarga se ha iniciado.
3) Cuando finalice la descarga, la carga será
iniciada automáticamente y la lámpara
4) Cuando el indicador luminoso CHARGE
%
parpadea y se apaga, se ha completado la
carga. Desenchufe el adaptador de aliment-
ación CA de la toma de corriente alterna.
Desconecte el adaptador de alimentación CA
de la cámara de video.
CHARGE
%
empieza a destellar.
ALMACENAMIENTO DE LAS PILAS:
Antes de almacenar los paquetes de pilas por un
largo período de tiempo, asegurarse de
descargarlos completamente tomando las
siguientes medidas para no reducir el rendimiento
de la pilas.
Para la extracción de la batería…
… deslice BATTERY RELEASE
9
y extraiga la
batería.
1) Coloque la pila en la videocámara sin ningún
Batería
BN-V10U
Tiempo de carga
approx. 1 hr. 30 min.
approx. 1 hr. 40 min.
approx. 2 hrs. 40 min.
cassette insertado.
2) Ajuste el conmutador de alimentación
” o “ ” mientras presiona el botón de
bloqueo localizado en el conmutador.
$
en
“
BN-V12U (opcional)
BN-V20U (opcional)
#
BN-V400U (opcional) approx. 5 hrs. 10 min.
Los tiempos de carga son para una batería
completamente descargada.
21
•
•
•
Durante la carga o descarga, la cámara de
video no puede ser operada.
ESPAÑOL — GUIA PARA OPERACIÓN RAPIDA
Si la unidad comienza a funcionar mal, deje de usarla
inmediatamente y consulte a su concesionario local de
JVC.
No es posible efectuar la carga o descarga
si se utiliza un tipo de batería equivocado.
Cuando efectúe la carga de la batería por
primera vez o después de un largo periodo
de almacenamiento, la lámpara CHARGE
% puede no se encender. Retire la batería
de la cámara de video, luego intente la
carga nuevamente.
Colocación/Extracción de un cassette
1) Abra completamente el monitor LCD
y
manténgalo alineado verticalmente con la
cámara (no lo incline de un lado). La prensa
•
•
Si el tiempo de funcionamiento de una
EJECT
)
por más de 2 segundos hasta que
batería
completamente
cargada
es
el sostenedor de cassette se abre. No aplique
fuerza para abrirlo.
2) Inserte o retire un cassette. Cuando lo inserte,
asegúrese de que la etiqueta esté hacia fuera.
extremadamente corta, la batería puede
estar estropeada. Adquiera una nueva
batería.
Efectúe la carga en lugares donde la
3) Presione el botón de cierre
+
para cerrar el
temperatura sea entre 10°C
y
35°C. La
compartimiento de cassette hasta que se
trabe. Cierre el monitor LCD.
gama de temperatura ideal para efectuar la
carga es de 20°C a 25°C. Si el ambiente es
muy frío, la carga puede resultar incompleta.
El tiempo de carga varía de acuerdo con la
temperatura ambiente y el estado de la
batería.
•
•
Cerrar el monitor LCD mientras que el
compartimiento de cassette todavia está
abierto puede causar daños en el monitor
LCD.
Asegúrese que la lengüeta de protección
contra borrado esté en la posición que
permite la grabación. De lo contrario, deslice
la lengüeta. Algunos cassettes tienen
lengüetas extraíbles. Si la lengüeta ha sido
extraída, cubra el orificio con cinta adhesiva.
El compartimiento de cassette no puede ser
abierto mientras la cámara de video está en
el modo de grabación o desconectada de la
fuente de alimentación.
•
•
Ya que el adaptador de CA procesa
electricidad internamente, el mismo se
calentará durante el uso. Asegúrese de
utilizarlo sólo en áreas bien ventiladas.
La siguiente operación interrumpirá la carga
o la descarga:
•
•
• Ajuste el interruptor de alimentación $ en
“PLAY”, “ ” o “ ”.
• Desconecte el adaptador de CA de la
cámara de video.
• Desenchufe el adaptador de CA del
tomacorriente de CA.
Compartimiento
de cassette
)
•
•
Extraiga la batería de la cámara de video.
Utilizando el adaptador de alimentación/
cargador de CA AA-V15, es posible cargar
la batería BN-V10U/V12U/V20U/V400U sin
la cámara de video. Sin embargo, no es
posible utilizarlo como un adaptador de CA.
Para evitar interferencias en la recepción, no
utilice el adaptador de CA cerca de una
radio.
Rueda dentada
•
•
Girar para
eliminar la
distensión.
+
El tiempo de grabación es significativamente
reducido cuando el modo de zoom o el
modo de espera de grabación es activado
repetidamente o el monitor LCD es utilizado
repetidamente.
Antes del uso prolongado, se recomienda
que prepare suficiente batería para cubrir 3
vezes el tiempo de filmación planeado.
Lengüeta de protección
contra borrado
•
22
GRABACIÓN
REPRODUCCIÓN
1) Cargue una cinta.
2) Ajuste el conmutador de alimentación
1) Retire el cubreobjetivo. Ajuste el conmutador
de alimentación
$
en “ ” o “ ” mientras
$
en
presiona el botón de bloqueo
#
localizado en
“PLAY” mientras presiona el botón de bloqueo
localizado en el conmutador. Para iniciar la
reproducción, presione 6
el conmutador.
#
Filmación utilizando el visor: Asegúrese que
el monitor LCD esté cerrado y bloqueado.
Filmación utilizando el monitor LCD:
Asegúrese que el monitor LCD esté
completamente abierto.
(
.
Para interrumpir momentáneamente
(reproducción de imágenes fijas), presione
6
(
. Para interrumpir la reproducción,
presione 7 . Presione 1 para
rebobinar, ¡ para avanzar rápido la cinta.
La cámara de video ingresa al modo de
Espera de grabación
)
~
y
PAUSE
3
es
&
mostrado.
La búsqueda de imagen a alta velocidad
(Búsqueda rápida) es posible presionando 1
•
El visor y el monitor LCD no pueden ser
utilizados
simultáneamente
en
esta
~
o ¡
&
durante la reproducción
o ¡
videocámara. Por lo tanto, cuando abra el
monitor LCD y lo incline hacia arriba hasta
180°, no será posible visualizar ninguna
imagen en el visor, sin embargo, podrá
filmarse a sí mismo mientras visualiza su
propia imagen en el monitor LCD.
(manteniendo presionado 1
~
&
durante la reproducción continuará la
búsqueda hasta que sea liberado). Para
reanudar la reproducción normal, presione 6
(
.
2) Presione el botón de inicio/parada de
Para GRABACIÓN DE VÍDEO/
REPRODUCCION DE VÍDEO
@
grabación
"
.
aparece mientras la
grabación está en progreso.
•
La cámara de video se desactiva
automáticamente después de 5 minutos en el
modo de espera de grabación o modo de
parada. Para activarla otra vez, ajuste el
•
Para interrumpir la grabación, presione el
botón de inicio/parada de grabación ". La
cámara de video reingresa al modo de
espera de grabación.
conmutador de alimentación
$
en “OFF”,
Para ajustar el brillo del monitor LCD:
Cuando el conmutador de alimentación $
está ajustado en “ ”, ajuste “LCD BRIGHT”
en SYSTEM MENU (੬ pág. 15).
Cuando el conmutador de alimentación $
está ajustado en “ ” u “OFF”, este ajuste no
puede ser ejecutado.
luego en “ ”, “ ” o “PLAY”.
Cuando el conmutador de alimentación
•
$
esté ajustado en “ ”, “ ” o “PLAY” y el
monitor LCD está abierto en un ángulo de 60
grados o más, el monitor LCD se enciende y el
visor se apaga automáticamente para ahorrar
energía.
La imagen reproducida puede ser visualizada
en el visor (con el monitor LCD apagado), en
el monitor LCD o en un TV conectado (੬ pág.
11, “Connections To A TV/VCR”).
Para controlar el volumen de los altavoces ",
gire MENU 1 hacia “+” para aumentar o hacia
“–” para disminuir. Mientras filme, el sonido no
será escuchado desde los altavoces.
•
•
$
#
O simplemente reproduzca la cinta en un
VCR de VHS utilizando el adaptador de
cassette.
੬
pág. 12
"
23
TERMS
A
P
AC Adapter....................................................pg. 7
Animation Recording...................................pg. 15
Auto Date Record........................................pg. 15
Auto/Manual Focus .....................................pg. 10
Auto Shut Off.................................................pg. 9
Picture Stabilizer .........................................pg. 14
Playback........................................................pg. 9
Program AE with Special Effects.................pg. 13
Provided Accessories....................................pg. 2
Q
Quick Review...............................................pg. 10
B
Backlight Compensation .............................pg. 10
Battery Pack............................................pg. 7, 18
Brighten/Darken The Image........................pg. 13
Brighten/Darken The LCD Monitor..........pg. 9, 15
R
Recording......................................................pg. 9
Recording Format (S-VHS/ S-VHS ET).......pg. 16
Recording Mode..........................................pg. 14
Retake.........................................................pg. 10
Rewind The Tape...........................................pg. 9
C
Cassette Adapter ........................................pg. 12
Charging The Battery Pack ...........................pg. 7
Clean The Camcorder.................................pg. 19
Connection To a VCR/ TV............................pg. 11
Counter Memory .........................................pg. 16
S
Shoulder Strap Attachment ...........................pg. 9
Specifications ..............................................pg. 20
Super LoLux (S. LX)....................................pg. 14
Super VHS Expansion Technology..............pg. 16
D
Date/ Time Display......................................pg. 15
Date/ Time Settings.......................................pg. 8
Demonstration Mode...............................pg. 1, 15
Digital Effects ..............................................pg. 13
Digital Zoom................................................pg. 14
Diopter Adjustment........................................pg. 8
T
Tape Counter...............................................pg. 16
Tape Dubbing ..............................................pg. 11
Tape Length Setting ....................................pg. 15
Tele Macro...................................................pg. 14
Time Base Corrector ...................................pg. 11
Time-Lapse Shooting ..................................pg. 15
Tracking .......................................................pg. 10
E
Erase Protection............................................pg. 9
Exposure Control ........................................pg. 13
V
Viewfinder Adjustment...................................pg. 8
F
W
Fade/Wipe-In/Out........................................pg. 13
Fast-Forward Tape ........................................pg. 9
5-Second Recording Mode .........................pg. 10
White Balance Adjustment ..........................pg. 14
Wide Mode ..................................................pg. 14
Z
G
Zooming ......................................................pg. 10
Grip Adjustment ............................................pg. 8
I
Instant Titles................................................pg.14
L
LCD Monitor/ Viewfinder, Indications ........pg. 5, 6
LED Light ....................................................pg. 13
Load/Unload A Tape......................................pg. 9
M
Menu Screen.......................................pg. 12 – 16
© 2005 Victor Company of Japan, Limited
Printed in Malaysia
US
1105YDR-NF-VM
|