JVC GR AXM917UM User Manual

COMPACT VHS CAMCORDER

ENGLISH

GR-AXM917UM

INSTRUCTIONS

LYT0299-001A

EN3

IMPORTANT PRODUCT

SAFETY INSTRUCTIONS

ANTENNA INSTALLATION

INSTRUCTIONS

1. Outdoor Antenna Grounding

Electrical energy can perform many useful functions.

But improper use can result in potential electrical

shock or fire hazards. This product has been

engineered and manufactured to assure your

personal safety. In order not to defeat the built-in

safeguards, observe the following basic rules for its

installation, use and servicing.

If an outside antenna or cable system is connected to

the product, be sure the antenna or cable system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810

of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding

of the mast and supporting structure, grounding of

the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge

unit, connection to grounding electrodes, and

requirements for the grounding electrode.

ATTENTION:

Follow and obey all warnings and instructions

marked on your product and its operating

instructions. For your safety, please read all the safety

and operating instructions before you operate this

product and keep this manual for future reference.

2. Lightning

For added protection for this product during a

lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the

wall outlet and disconnect the antenna or cable

system. This will prevent damage to the product due

to lightning and power-line surges.

INSTALLATION

1. Power Sources

Operate your product only from the type of power

source indicated on the marking label. If you are not

sure of the type of power supply to your home,

consult your product dealer or local power company.

If your product is intended to operate from battery

power, or other sources, refer to the operating

instructions.

3. Power Lines

An outside antenna system should not be located in

the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside

antenna system, extreme care should be taken to

keep from touching such power lines or circuits as

contact with them might be fatal.

2. Overloading

Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in

a risk of fire or electric shock.

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

3. Power Cord Protection

Power supply cords should be routed so that they are

not likely to be walked on or pinched by items

placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles,

and the point where they exit from the product.

ANTENNA

LEAD IN WIRE

GROUND CLAMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION

4. Ventilation

810-20)

ELECTRIC SERVICE

EQUIPMENT

Slots and openings in the cabinet are provided for

ventilation. To ensure reliable operation of the

product and to protect it from overheating, these

openings must not be blocked or covered.

•Do not block the openings by placing the product

on a bed, sofa, rug or other similar surface.

•Do not place the product in a built-in installation

such as a bookcase or rack unless proper

ventilation is provided or the manufacturer’s

instructions have been adhered to.

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

5. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling

only as recommended by the manufacturer.

USE

SERVICING

1. Servicing

1. Accessories

To avoid personal injury:

If your product is not operating correctly or exhibits a

marked change in performance and you are unable

to restore normal operation by following the detailed

procedure in its operating instructions, do not

attempt to service it yourself as opening or removing

covers may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service

personnel.

•Do not place this product on an unstable cart,

stand, tripod, bracket or table. It may fall, causing

serious injury to a child or adult, and serious

damage to the product.

•Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer or sold with the

product.

•Use a mounting accessory recommended by the

manufacturer and follow the manufacturer’s

instructions for any mounting of the product.

•Do not try to roll a cart with small casters across

thresholds or deep-pile carpets.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer

servicing to qualified service personnel under the

following conditions:

a. When the power supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen

into the product.

2. Product and Cart

Combination

A product and cart

PORTABLE CART WARNING

(Symbol provided by RETAC)

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the product to its normal operation.

e. If the product has been dropped or damaged in

any way.

combination should be

moved with care. Quick

stops, excessive force, and

uneven surfaces may cause

the product and cart

combination to overturn.

3. Water and Moisture

Do not use this product near water—for example,

near a bath tub, wash bowl, kitchen sink or laundry

tub, in a wet basement, or near a swimming pool and

the like.

f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

4. Object and Liquid Entry

When replacement parts are required, be sure the

service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock or other

hazards.

Never push objects of any kind into this product

through openings as they may touch dangerous

voltage points or short-out parts that could result in a

fire or electric shock. Never spill liquid of any kind

on the product.

5. Attachments

4. Safety Check

Do not use attachments not recommended by the

manufacturer of this product as they may cause

hazards.

Upon completion of any service or repairs to this

product, ask the service technician to perform safety

checks to determine that the product is in safe

operating condition.

6. Cleaning

Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat

sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce

heat.

MAJOR FEATURES

EN5

REMEMBER

Digital Still Camera Built-in

(PC communication capable)

(੬ pg. 22 – 25, 52 – 59)

The Logical Choice

Menu Adjustment

(੬ pg. 36, 37, 38)

The only compact video

cassettes that can be

used with your VHS VCR*

Integrated Auto Light

(੬ pg. 30)

Program AE with Special

Effects (੬ pg. 32, 33)

Picture Stabilizer (੬ pg. 29)

Ⅲ Electronic Fog Filter

Ⅲ ND Effect

Ⅲ Sepia

Ⅲ Twilight

Ⅲ Sports

Ⅲ Nega/Posi

Ⅲ 1/2000 sec. High Speed Shutter

Digital Hyper Zoom

(੬ pg. 28)

Zoom in

LCD Color Monitor

(੬ pg. 20)

Zoom out

Cassettes marked

camcorder.

can be used with this

QUICK OPERATION GUIDE (VIDEO)

The image you shoot is recorded onto a video tape.

SUPPLY POWER

INSERTING A VIDEO

CASSETTE

Hook on.

B Push in.

PUSH Button

EJECT Switch

BATTERY RELEASE

Using the battery pack

1 Open the LCD monitor to an angle of over 60

degrees.

Hook its end to the camcorder ( ) and push the

battery pack in until it locks in place ( ).

(Charging procedure, ੬ pg. 10)

2 Slide EJECT to open the cassette holder.

3 Insert a video cassette.

To remove the battery pack

Slide BATTERY RELEASE and pull out the battery

pack.

4 Press PUSH to close the cassette holder.

(For more details, ੬ pg. 15)

SHOOTING

PLAYBACK

REW (2) Button

LENS COVER

Open/Close Ring

Set to “AUTO”

or “PRO.”

4 ^P₍^LAY/PAUSE

4/6) Button

Set to “PLAY”

Recording Start/Stop Button

STOP (5) Button

Set to “VIDEO”

1 Set the System Select Switch to “VIDEO”.

2 Set the Power Switch to “PLAY”.

3 Press REW (2).

1 Turn the LENS COVER Open/Close Ring to

open the lens cover.

2 Set the System Select Switch to “VIDEO”.

3 Set the Power Switch to “AUTO” or “PRO.”.

— The power lamp will light and an image

will appear.

— The tape will automatically stop at the

beginning of the tape.

4 Press PLAY/PAUSE (4/6).

— Playback starts and the playback picture

appears.

•To stop playback, press STOP (5).

(For more details, ੬ pg. 46.)

•The viewfinder switches off automatically to

save power when the LCD monitor is opened

at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is

opened/closed at approx. 60 degrees.

4 Press the Recording Start/Stop Button.

— Recording starts.

•To stop recording temporarily, momentarily

press the Recording Start/Stop Button once

again.

(For more details, ੬ pgs. 18 – 21)

•The viewfinder switches off automatically to

save power when the LCD monitor is opened

at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is

opened/closed at approx. 60 degrees.

Or simply play back the tape on a VHS VCR

using the Cassette Adapter (VHS Playpak).

੬ pg. 49

QUICK OPERATION GUIDE (D.S.C.)

A still image you shoot is stored in the camcorder's built-in memory.

EN7

SHOOTING

SUPPLY POWER

Hook on.

B Push in.

SNAPSHOT Button

LENS COVER

Open/Close Ring

Set to “AUTO”

or “PRO.”

System Select Switch

Set to “D.S.C.”

BATTERY RELEASE

Using the battery pack

Hook its end to the camcorder ( ) and push the

battery pack in until it locks in place ( ).

(Charging procedure, ੬ pg. 10)

To remove the battery pack

Slide BATTERY RELEASE and pull out the battery

pack.

1 Turn the LENS COVER Open/Close Ring to

open the lens cover.

2 Set the System Select Switch to “D.S.C.”.

3 Set the Power Switch to “AUTO” or “PRO.”.

— The power lamp will light and an image

will appear.

4 Press the SNAPSHOT Button.

— A still image is shot and is stored in the

camcorder’s memory.

PLAYBACK

(For more details, ੬ pgs. 22 – 25)

REW (2/PAGE –) Button,

•The viewfinder switches off automatically to

save power when the LCD monitor is opened

at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is

opened/closed at approx. 60 degrees.

FF (3/PAGE +) Button

Set to “PLAY”

System Select Switch

Set to “D.S.C.”

1 Set the System Select Switch to “D.S.C.”.

2 Set the Power Switch to “PLAY”.

— A still image stored in memory appears.

3 Press REW (2/PAGE –) or FF (3/PAGE +) to

select the still image you want to view.

(For more details, ੬ pg. 52.)

•The viewfinder switches off automatically to

save power when the LCD monitor is opened

at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is

opened/closed at approx. 60 degrees.

CONTENTS

GETTING STARTED

10 – 17

Power.......................................................................................................... 10

Clock (Lithium) Battery Insertion/Removal .............................................................. 12

Date/Time Settings.......................................................................................... 13

Recording Mode Setting..................................................................................... 14

Tape Length Setting .......................................................................................... 14

Loading/Unloading A Cassette............................................................................. 15

Grip Adjustment .............................................................................................. 16

Viewfinder Adjustment ..................................................................................... 16

Shoulder Strap Attachment ................................................................................. 17

Tripod Mounting .............................................................................................. 17

VIDEO RECORDING

18 – 21

Basic Recording............................................................................................... 18

DIGITAL STILL CAMERA (D.S.C.) SHOOTING

22 – 25

Basic Shooting ................................................................................................ 22

RECORDING

26 – 45

Basic Features ................................................................................................ 26

Advanced Features........................................................................................... 31

VIDEO PLAYBACK

46 – 49

Basic Playback................................................................................................ 46

Features ....................................................................................................... 47

Using The Cassette Adapter ................................................................................ 49

PLAYBACK

50 – 51

Basic Connections And Tape Dubbing ...................................................................... 50

D.S.C. PLAYBACK

52 – 59

Basic Playback................................................................................................ 52

Connection .................................................................................................... 53

Advanced Features........................................................................................... 54

USING THE REMOTE CONTROL UNIT

60 – 64

Insert Editing (VIDEO)....................................................................................... 62

Insert Editing (Insert A Still Image From The Built-in Memory Onto A Tape) ....................... 63

Audo Dubbing................................................................................................. 64

EN9

USER MAINTENANCE

TROUBLESHOOTING

INDEX

66 – 68

69 – 73

Controls, Connectors And Indicators ...................................................................... 69

Indications..................................................................................................... 71

Terms .......................................................................................................... 72

CAUTIONS

74 – 76

SPECIFICATIONS

OPTIONAL ACCESSORIES

PROVIDED ACCESSORIES

•AC Power Adapter/

Charger AA-V15U

•Cassette Adapter

(VHS Playpak) C-P7U

•Battery Pack

BN-V20U

•Shoulder Strap

•DC Cord

•Remote Control

Unit RM-V705U

(for Windows^®PC)

•Lithium Battery CR2025 x 2

(for clock operation and

remote control unit)

•CD-ROM including two

software programs

•PC Connection Cable x 1

GETTING STARTED

Marks

Power

This camcorder’s 3-way power supply system lets you choose

the most appropriate source of power.

To AC outlet

CHARGE indicator

NOTES:

● No function is available without power supply.

● Use only the specified power supply.

● Do not use provided power supply units with other

equipment.

CHARGING THE BATTERY PACK

REFRESH switch

SUPPLY POWER

1 _{Connect the charger’s AC power cord to a wall outlet.}

REFRESH indicator

ATTACH BATTERY PACK

2 _{Align the marks and slide the battery pack in the}

REFRESH

direction of the arrow until it locks in place.

The AC Power Adapter/Charger features a

REFRESH function that allows you to fully

discharge the battery pack before recharg-

ing.

Perform the REFRESH function after no less

than 5 chargings.

•The CHARGE indicator begins blinking to indicate

charging has started.

DETACH BATTERY PACK

3 _{When the CHARGE indicator stops blinking but stays lit,}

charging is finished. Slide the battery pack opposite the

direction of the arrow.

To discharge the battery . . .

.... attach the battery pack to the adapter as

shown in the above illustration. Then

push REFRESH. The REFRESH indicator

lights when discharging starts, and goes

out when discharging is complete.

Battery pack

BN-V12U

BN-V20U

Charging time

approx. 1 hr. 10 min.

approx. 1 hr. 50 min

Discharging time

approx. 3 hrs. 30 min.

approx. 6 hrs. 40 min.

USING THE BATTERY PACK

ATTACH BATTERY PACK

Hook on.

1 _{Hook its end to the camcorder (}

) and push the battery

Push in.

pack in until it locks in place (

) .

DETACH BATTERY PACK

2 _{Slide BATTERY RELEASE and pull out the battery pack.}

Approximate recording time (unit: min.)

LCD

Battery pack monitor on/

monitor off/

monitor on/

Viewfinder off Viewfinder on Viewfinder on

BN-V12U

BN-V20U

45 (30)

80 (50)

50 (35)

85 (55)

40 (30)

70 (45)

BATTERY RELEASE

(

) : when the video light is on.

INFORMATION:

VU-V856KIT is a set composed of the BN-V856U battery pack

and AA-V80U AC Power Adapter/Charger.

ATTENTION:

Before detaching the power source,

make sure that the camcorder’s power

is turned off. Failure to do so can result

in a camcorder malfunction.

The BN-V856U battery pack provides approx. 7 hours of

recording time when the viewfinder is on and the LCD

monitor and the video light are off. Also read thoroughly the

VU-V856KIT’s instruction manuals.

It is impossible to charge the BN-V856U battery pack using

the provided AC Power Adapter/Charger. Use the optional

AA-V80U AC Power Adapter/Charger.

EN11

Charge Marker

A charge marker is provided on the battery pack to

help you remember whether it has been charged or

not. Two colors are provided (red and black)—you

choose which one means charged and which means

discharged.

Charge marker

NOTES:

● The recording time per charge is affected by such factors as the time spent in Record-Standby mode and the

frequency of zooming. It is safer to have spare battery packs to cover 3 times the planned shooting time.

● Charging times noted on page 10 are for a fully discharged battery pack, and discharging times are for a fully

charged battery pack.

● Charging and discharging times vary according to the ambient temperature and the status of the battery pack.

● Remember to set the charge marker after charging a battery pack or after detaching a discharged one from

your camcorder.

● Perform the REFRESH function after no less than 5 chargings.

● While the AC Power Adapter/Charger’s power cord is disconnected from the AC outlet, it is possible to

discharge the battery by pressing the REFRESH switch. During that time, the AC Power Adapter/Charger does

not charge the battery. When discharging is complete, detach the battery from the AC Power Adapter/

Charger to store it.

● High temperatures can damage the battery pack, so use only where good ventilation is available. Do not

allow it to discharge in a container, such as a bag.

● If you stop recharging or discharging part way through, make sure to remove the battery pack before

unplugging the adapter’s AC cord.

● Remove the battery pack from the adapter immediately after discharging.

● To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.

● Make sure you unplug the DC cord before charging or discharging the battery pack.

● The CHARGE indicator may not light properly with a brand new battery pack, or with one that has been

stored for an extended period. In this case, remove and reattach the battery pack and recharge it. The

CHARGE indicator should blink during recharging. If it doesn’t, contact your nearest JVC dealer.

USING AC POWER

To DC IN jack

To AC outlet

Use the AC Power Adapter/Charger (connect as

shown in the illustration to the left).

DC OUT

terminal

NOTES:

● The provided AC Power Adapter/Charger features

automatic voltage selection in the AC range from

110 V to 240 V.

AC Power

Adapter/Charger

AA-V15U

● When using the DC cord, make sure you connect

the end of the cord with the core filter to the

camcorder. The core filter reduces interference.

DC Cord

USING A CAR BATTERY

Use the optional Car Battery Cord or Car Battery

Charger/Adapter (connect as shown in the

illustration to the left).

To car’s

cigarette

lighter

socket

Car Battery Cord

AP-V7U (optional)

NOTES:

● When using the car battery, leave the engine

idling.

● The optional Car Battery Charger/Adapter

(BH-V3U) can also be used to charge the battery

pack (except BN-V20U/V856U).

● When using the optional Car Battery Charger/

Adapter or Car Battery Cord (AP-V7U), refer to the

respective instruction booklet.

Car Battery

Charger/Adapter

BH-V3U (optional)

GETTING STARTED (cont.)

Slot

Clock (Lithium) Battery Insertion/Removal

This battery is necessary for clock operation and to

perform date/time settings.

SWITCH OFF POWER

1 _{Switch off the unit’s power and remove the power}

supply unit (battery pack, AC Power Adapter/Battery

Charger, etc.).

REMOVE BATTERY HOLDER

2 _{Pull out the battery holder.}

Battery holder

INSERT BATTERY IN HOLDER

3 _{Insert the battery in the holder, and be sure to have}

the “+” mark visible.

RE-INSERT HOLDER

4 _{Slide the holder back into the slot until you hear a}

click.

NOTE:

See “SAFETY PRECAUTIONS” (੬ pg. 2) for information

on safe handling of lithium batteries.

EN13

Date/Time Settings

SELECT OPERATION SYSTEM AND

1 _MODE

System

Select Switch

Set the System Select Switch to “VIDEO” or “D.S.C.” ,

and set the Power Switch to “PRO.”.

•The power lamp comes on.

ACCESS MENU SCREEN

2 _{Press MENU.}

SELECT FUNCTION

MENU Button

3 _{Rotate the Select Dial to move the highlight bar to}

“DATE/TIME”, then press it. The DATE/TIME Menu

appears.

Power lamp

•If you decide you want to return the date and time

to the previous settings, rotate the Select Dial to

move the highlight bar to “EXIT” and press it, then

go to step 7.

•If you want to set only the time without changing

the date, go to step 5.

Select Dial

Power Switch

SET DATE

4 _{Rotate the Select Dial to move the highlight bar to the}

Display

item you want to set and then press it. When the

setting begins blinking, rotate the Select Dial until the

correct setting appears and then press it. The setting

stops blinking.

Menu Screen

M.W.B.

AUTO

D . ZOOM

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

FINE

FULL

•Repeat this procedure until you’re satisfied with the

Date settings (“YEAR”, “MONTH” and “DAY”).

SNAPSHOT

4RETURN

SET TIME

5 _{Rotate the Select Dial to move the highlight bar to}

DATE TIME

DATE/TIME Menu

“TIME” and then press it. When the hour setting

begins blinking, rotate the Select Dial until the correct

setting appears and then press it. When the hour

setting stops blinking and the minute setting begins

blinking, rotate the Select Dial until the correct setting

appears and then press it. The minute setting stops

blinking.

YEAR

1999

JAN

MONTH

DAY

TIME

PM 12 : 00

12-hour indication

with AM or PM

EXIT

START CLOCK OPERATION

6 _{When none of these settings (“YEAR”, “MONTH”,}

M.W.B.

AUTO

D . ZOOM

“DAY”, “TIME”) blinks, rotate the Select Dial to move

the highlight bar to “EXIT”, and press it. The Menu

Screen reappears with the highlight bar on

“RETURN”.

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

FINE

FULL

SNAPSHOT

4RETURN

CLOSE MENU SCREEN

7 _{Press the Select Dial.}

NOTE:

To display the date and time in the camcorder’s display

and on a connected TV, see “Date/Time Insert”

(੬ pg. 34).

GETTING STARTED (cont.)

Recording Mode Setting

Set depending on your preference.

SET RECORDING MODE

System

Select Switch

1 _{First set the System Select Switch to “VIDEO”, then}

set the Power Switch to “AUTO” or “PRO.”. Press SP/

EP for more than 1 second. “SP” (Standard Play)

provides higher picture and sound quality and is

better for dubbing, while “EP” (Extended Play) is

more economical, providing three times the record-

ing time.

MENU Button

SP/EP Recording

NOTE:

If the recording mode is switched during recording, the

playback picture will be blurred at the switching point.

Mode Button

Tape Length Setting

Set the tape length according to the length of the tape

used.

Select Dial

Viewfinder

Power Switch

ACCESS MENU SCREEN

1 _{First set the System Select Switch to “VIDEO”, then}

T30

Tape length indicator

set the Power Switch to “PRO.”. Press MENU.

SELECT FUNCTION

Recording mode

indicator

2 _{Rotate the Select Dial to move the highlight bar to}

“TAPE LENGTH”, then press it. The TAPE LENGTH

Setting Menu appears.

SET TAPE LENGTH

Display

3 _{Rotate the Select Dial to move the highlight bar to the}

correct setting. T20=20 minutes of recording time,

T30=30 minutes, and T40=40 minutes (in SP).

Menu Screen

M.W.B.

AUTO

D . ZOOM

TELE MACRO OFF

DATE TIME

•If you decide you want to return the tape length to

the previous setting, rotate the Select Dial to move

the highlight bar to “EXIT”.

TAPE LENGTH T30

PICTURE

FINE

FULL

SNAPSHOT

RETURN

CLOSE MENU SCREEN

4 _{Press the Select Dial. The Menu Screen reappears}

TAPE LENGTH

with the highlight bar on “RETURN”. Press the Select

Dial again to close the Menu Screen.

TAPE LENGTH

Setting Menu

T20

T30

T40

NOTE:

The tape remaining time (੬ pg. 19) displayed in the

viewfinder is correct only if the correct tape length has

been selected.

EXIT

M.W.B.

AUTO

D . ZOOM

TELE MACRO OFF

DATE TIME

TAPE LENGTH T40

PICTURE

FINE

FULL

SNAPSHOT

4RETURN

EN15

Cassette holder

Loading/Unloading A Cassette

OPEN LCD MONITOR

1 _{Open the LCD monitor to an angle of over 60}

degrees.

OPEN CASSETTE HOLDER

2 _{Slide EJECT until the holder opens. Do not use force}

to open.

INSERT/REMOVE CASSETTE

3 _{Make sure the label is facing outward.}

PUSH Button

EJECT Switch

CLOSE CASSETTE HOLDER

4 _{Press PUSH and make sure the holder is closed and}

locked.

CLOSE LCD MONITOR

5 _{First make sure the holder is closed. Then close the}

LCD monitor.

Turn to take

up slack.

NOTES:

● Closing the LCD monitor while the cassette holder is still

open may cause damage to the LCD monitor.

● The cassette holder can’t be opened unless a power

supply is attached.

Erase Protection

Gear

● Make sure that the tape is not slack when loading the

cassette. If there is any slack, turn the gear on the

cassette in the direction of the arrow to take up the

slack.

● Make sure the Erase Protection tab is in the position that

allows recording. If not, slide the tab. Some cassettes

have removable tabs. If the tab has been removed, cover

the hole with adhesive tape.

● The cassette holder cannot be opened while the

camcorder is in the record mode.

GETTING STARTED (cont.)

Grip Adjustment

Power Zoom Lever

EXPAND LOOP

1 _{Separate the Velcro strip.}

INSERT HAND

2 _{Pass your right hand through the loop and grasp the}

grip.

ADJUST STRAP LENGTH

3 _{Adjust so your thumb and fingers can easily operate}

the Recording Start/Stop Button and Power Zoom

Lever. Refasten the Velcro strip.

Recording Start/Stop Button

Viewfinder Adjustment

SELECT OPERATION MODE

1 _{Set the Power Switch to “CAMERA” (“AUTO” or}

“PRO.”).

POSITION VIEWFINDER

180°

2 _{Adjust the viewfinder manually for best viewability}

(see illustration at left).

ADJUST DIOPTER

3 _{Turn the Diopter Adjustment Control until the}

indications in the viewfinder are clearly focused.

Set “POWER” to

“CAMERA”

(“AUTO” or “PRO.”)

PAUSE

EN17

Shoulder Strap Attachment

ATTACH STRAP

1 _{Following the illustration at left, thread the strap}

through the top of the eyelet 1, then fold it back and

thread it through the buckle 2. Repeat the procedure

to attach the other end of the strap to the other eyelet

3, making sure the strap is not twisted.

ADJUST LENGTH

2 _{Adjust as shown in the illustration at left 4.}

Tripod Mounting

ALIGN AND TIGHTEN

1 _{Align the screw and camera direction stud on the}

tripod with the camera’s mounting socket and stud

hole. Then tighten the screw.

CAUTION:

When using a tripod, be sure to open and extend

its legs fully to stabilize the camcorder. To

prevent damage to the unit caused by falling

over, do not use a small-sized tripod.

VIDEO RECORDING Basic Recording

System Select Switch

LENS COVER

Open/Close Ring

NOTE:

You should already have performed the procedures listed

below. If not, do so before continuing.

● Power (੬ pg. 10)

● Recording Mode Setting (੬ pg. 14)

● Tape Length Setting (੬ pg. 14)

● Grip Adjustment (੬ pg. 16)

● Viewfinder Adjustment (੬ pg. 16)

LOAD A CASSETTE

1 _{First open the LCD monitor to an angle of over 60}

degrees.

Slide EJECT to open the cassette holder, then insert

the cassette with the label facing out. Press PUSH to

ensure the holder is closed and locked.

Power Switch

Recording Start/Stop Button

EJECT Switch

Shooting While Watching The Viewfinder

Power lamp

ENTER RECORD-STANDBY MODE

2 _{Make sure the LCD monitor is closed and locked.}

Turn the LENS COVER Open/Close Ring to open the

lens cover. Set the System Select Switch to “VIDEO”,

then set the Power Switch to “CAMERA” (“AUTO” or

“PRO.”).

•The power lamp lights and the camcorder enters the

Record-Standby mode.

Tally lamp

(lights while recording is in progress)

•The scene you are aimed at appears on the

viewfinder screen, with the word “PAUSE”

superimposed upon it.

START SHOOTING

3 _{Press the Recording Start/Stop Button.}

•“

” appears in the viewfinder while recording is

in progress.

Power Switch Position

According to the Power Switch position you have selected, the following functions are available:

AUTO

(Full Auto mode):

PRO.

(PRO. mode):

POWER OFF:

Allows you to record using

Allows you to set various

recording functions using the

menus. If you want more creative

capabilities than full auto

recording, try this mode.

Allows you to switch off the

camcorder.

NO special effects or manual

adjustments. Suitable for

standard recording.

EN19

Tape remaining time indicator

STOP RECORDING

4 _{Press the Recording Start/Stop Button again to stop}

25MIN

MIN

(Now calculating)

recording.

•The camcorder re-enters the Record-Standby mode.

120MIN

119MIN

NOTES:

● When the Power Switch is set to CAMERA and the LCD

monitor is opened at an angle of 60 degrees or more, the

LCD monitor switches on and the viewfinder switches

off automatically to save power.

3MIN

● The cassette holder cannot be opened unless a power

supply is attached.

2MIN

(Blinking)

● There may be a delay after you slide EJECT until the

holder opens. Do not use force.

● The tape remaining time is only displayed in the

viewfinder as shown.

1MIN

● The remaining time indicated in the viewfinder is

approximate.

(Blinking)

● The time required to calculate the remaining tape

length, and the accuracy of the calculation, may vary

according to the type of tape used.

0MIN

(Blinking)

● The tape remaining time indicator is correct only if the

correct tape length has been selected (੬ pg. 14).

● “TAPE END” appears when the tape reaches its end, and

the power goes off automatically if left in this condition

for 5 minutes. “TAPE END” also appears when a cassette

whose tape is already at its end is loaded.

Recording Start/Stop Button

● If the Record–Standby mode continues for 5 minutes

without performing Zoom or any other operations, the

camcorder’s power shuts off automatically. Set the

Power Switch to “POWER OFF”, and then back to

“CAMERA” to turn the camcorder on again.

● If the Recording Start/Stop button is pressed after the

Record-Standby mode has continued for over

5 minutes, recording may not start immediately.

● If you are recording on a cassette from the middle (such

as when a tape is removed and re-inserted during

recording), use the Retake function (੬ pg. 29) to find

the end of the last recording so you don’t erase any of it.

● The LENS COVER warning blinks for about 5 seconds

when the camcorder is turned on with the cover closed.

● While shooting, sound is not heard from the speaker.

● To turn the tally lamp off during recording, refer to pgs.

36 and 38.

DISPLAY Button

LCD Monitor/Viewfinder Indications

Press DISPLAY to make the following indications appear/

disappear from the camcorder’s display: cassette warning,

tape remaining time, battery pack remaining power

indicator and tape length indicator (੬ pg. 71).

PRESS DISPLAY BUTTON

1 _{To turn off the indications, press DISPLAY for more}

than 1 second.

Press again for more than 1 second to make the

indications reappear.

NOTE:

Even if the indications are off, the tape remaining time

appears blinking when the tape is near its end, and the

battery pack remaining power indicator appears blinking

when the power is almost gone.

VIDEO RECORDING Basic Recording (cont.)

Shooting While Watching The LCD Monitor

Before the following steps, perform step 1 (੬ pg. 18).

90°

180°

ENTER RECORD–STANDBY MODE

2 _{Make sure the LCD monitor is fully open. Turn the}

LENS COVER Open/Close Ring to open the lens

cover. Set the System Select Switch to “VIDEO”,

then set the Power Switch to “CAMERA” (“AUTO” or

“PRO.”).

•The power lamp lights and the camcorder enters the

Record-Standby mode.

•The scene you are aimed at appears in the LCD

monitor, with the word “PAUSE” superimposed

upon it.

System Select Switch

LENS COVER

Open/Close Ring

START SHOOTING

3 _{Tilt the LCD monitor upward/downward for best}

viewability (੬ pg. 21) and press the Recording Start/

Stop Button.

•“

” appears in the LCD monitor while recording

is in progress.

STOP RECORDING

4 _{Press the Recording Start/Stop Button again to stop}

Power Switch

recording.

•The camcorder re-enters the Record-Standby mode.

Recording Start/Stop Button

Power lamp

NOTES:

● When you use the LCD monitor outdoors in direct

sunlight, the LCD monitor may be difficult to see. If this

happens, we recommend that you use the viewfinder

(੬ pg. 18).

● To turn the tally lamp off during recording, refer to pgs.

36 and 38.

● For other notes, refer to pg. 19.

Tally lamp

(lights while recording is in progress)

EN21

Journalistic Shooting

In some situations different angles of shooting may be

required for more dramatic results.

OPEN LCD MONITOR

1 _{Make sure the LCD monitor is fully open.}

TILT LCD MONITOR

2 _{Tilt the LCD monitor in the most convenient}

direction.

•The LCD monitor can rotate almost full circle (270°:

90° downward, 180° upward).

Interface Shooting

The person you shoot can view himself/herself in the

LCD monitor, and you can even shoot yourself while

viewing your own image in the LCD monitor.

TILT LCD MONITOR UPWARD

1 _{Open the LCD monitor and tilt it upward to 180}

Self-recording

degrees so that it faces forward.

•When the LCD monitor is tilted upward to an angle

of over approx. 105 degrees, the monitor image is

inverted vertically, and the viewfinder also switches

on.

START RECORDING

2 _{Point the lens toward the subject (yourself when self-}

recording) and start recording.

•During Interface Shooting, the monitor image and

indications do not appear inverted as they would

when viewing a mirror.

NOTE:

The monitored image can be viewed on the LCD monitor

and in the viewfinder.

Brightness Control

You can adjust the brightness of the LCD monitor by

turning the BRIGHT Dial.

ADJUST BRIGHTNESS

1 _{If you want to brighten the image . . .}

Turn the Dial towards “+”.

If you want to darken the image . . .

Turn the Dial towards “–”.

BRIGHT Dial

DIGITAL STILL CAMERA (D.S.C.) SHOOTING

SNAPSHOT Button LENS COVER

Basic Shooting

Open/Close Ring

When shooting a still image, it is not recorded onto the

tape, but it is stored in the camcorder’s built-in memory in

the selected Picture Mode. A stored still image data can be

transferred to a PC, saved, and processed using a Paint

Software program (੬ pg. 53).

System

Select

Switch

MODE SELECTION

SELECT OPERATION SYSTEM AND

1 _MODE

Turn the LENS COVER Open/Close Ring to open the

lens cover, then set the System Select Switch to

“D.S.C.”. Set the Power Switch to “PRO.”.

MENU Button

Power lamp

• The power lamp lights and an image appears.

SELECT PICTURE MODE

2 _{Do steps 2 and 3 of “OPERATION” on pg. 24.}

Set “PICTURE” to “FINE” or “STANDARD” in the

Menu Screen as required.

•There are two modes: FINE allows you to shoot up

to approx. 30 still images with higher resolution,

and STANDARD allows you to shoot up to approx.

60 still images with lower resolution.

Select Dial

Display

Power Switch

Menu Screen

M.W.B.

AUTO

SELECT SNAPSHOT MODE

D . ZOOM

TELE MACRO OFF

DATE TIME

3 _{Rotate the Select Dial to move the highlight bar to}

TAPE LENGTH T30

“SNAPSHOT”, and press it. The SNAPSHOT Menu

appears.

PICTURE

FINE

SNAPSHOT

FULL

Rotate the Select Dial to move the highlight bar to the

appropriate mode among the 5 Snapshot modes

(੬ pg. 23), and press it. Selection is complete.

RETURN

SNAPSHOT

SNAPSHOT Menu

CLOSE MENU SCREEN

FULL

PIN UP

MULTI

4 _{The Menu Screen reappears with the highlight bar on}

“RETURN”. Press the Select Dial again to close the

Menu Screen.

M.DRIVE

STILL IMAGE STORAGE

EXIT

TAKE SNAPSHOT

1 _{Press SNAPSHOT.}

Menu Screen

M.W.B.

AUTO

D . ZOOM

•Regardless of the Power Switch position (“AUTO”

or “PRO.”), Snapshot recording takes place using

the selected Snapshot mode.

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

FINE

PIN-UP

SNAPSHOT

•A still image is stored in the built-in memory and

displayed for approx. 2 seconds. While the still

image remains displayed, that image is in the

process of being stored in memory, and it is

therefore impossible to take another shot during that

time. When the still image disappears and the scene

you are currently aimed at appears on the screen,

you may take another shot.

4RETURN

Normal Screen

During Snapshot mode

No display

(Full)

(Pin-Up)

•The remaining number of shots available is

displayed.

MD (M.DRIVE)

M4 (MULTI-4)

M9 (MULTI-9)

EN23

Remaining number

of shots

NOTES:

● The remaining number of shots varies according to the

selected Picture Mode. In the “STANDARD” mode,

twice as many still images can be shot as in the “FINE”

mode.

FINE 12

30 29

(Blinking)

● Some sample images have been stored in the built-in

memory at the factory.

If you wish to delete them, first remove the “Protect”

function (੬ pg. 57), then perform the “Delete” function

(੬ pg. 58).

Pictrue mode

display

● When the Power Switch is set to “AUTO”, it is not

possible to select the Snapshot mode. You can use the

Snapshot mode you selected in the “PRO.” mode.

● If a Snapshot is taken while the camcorder is in the

WIDE mode (੬ pg. 37), the Snapshot image is

recorded without the black bars at the top and bottom of

the screen.

FULL*

(Snapshot mode with

no frame)

PIN-UP*

(Pin-Up mode)

MULTI-4 **

(Multi-Analyzer 4)

MULTI-9**

(Multi-Analyzer 9)

* There is a momentary camera shutter-type blackout

together with the image.

** Continuous camera shutter-type blackout takes place 4

or 9 times with the image, like serial photography, then

the 4 or 9 still images you took are displayed.

M. DRIVE

(Motor Drive mode)

Stores 6 still images continuously for approx. 2 seconds.

During still image storage, “MD” blinks and the 6 still

images are displayed in the order that you took them.

There is no sound effect of a shutter closing.

CONTINUED ON NEXT PAGE

D.S.C. SHOOTING (cont.)

SNAPSHOT Button

FEATURE: Picture Mode Setting

PURPOSE:

There are two image settings you can choose from

when storing in the camcorder's memory: FINE and

STANDARD. FINE allows you to shoot up to approx.

30 still images in a format based on JPEG (Joint

Photographic Experts Group). Since the quality of

image is better than “STANDARD”, “FINE” is more

suitable for post-production on a PC. “STANDARD”

allows you to shoot up to approx. 60 still images in a

format based on JPEG (Joint Photographic Experts

Group). Since in this mode, twice as many still images

can be shot as in the “FINE” mode, select this mode

when you wish to shoot many still images.

System

Select

Switch

MENU Button

OPERATION:

1) Turn the LENS COVER Open/Close Ring to open the

lens cover, and set the System Select Switch to

“D.S.C.”. Set the Power Switch to “PRO.”.

2) Press MENU. The Menu Screen appears.

Ⅲ If you wish the Picture Mode to return to the previous

setting, rotate the Select Dial to move the highlight

bar to “RETURN”.

3) Rotate the Select Dial to move the highlight bar to

“PICTURE”, and press it. The PICTURE Menu

appears.

Rotate the Select Dial to move the highlight bar to

“FINE” or “STANDARD”, and press it. Selection is

complete.

4) The Menu Screen reappears with the highlight bar

on “RETURN”. Press the Select Dial again to close

the Menu Screen.

Select Dial

Display

Power Switch

Menu Screen

M.W.B.

AUTO

D . ZOOM

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

FINE

FULL

SNAPSHOT

RETURN

PICTURE

PICTURE Menu

FINE

STANDARD

EXIT

Menu Screen

M.W.B.

D . ZOOM

AUTO

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

STD

FULL

SNAPSHOT

4RETURN

Normal Screen

Remaining number

of shots

STD 12

(Blinking)

Picture mode display

STD FINE

EN25

NOTES:

● The picture mode’s factory-preset is FINE.

● Some sample images have been stored in the built-in memory at the factory.

If you wish to delete them, first remove the “Protect” function (੬ pg. 57), then perform the “Delete”

function (੬ pg. 58).

● To store the still images you shot, we recommend that you transfer them to a computer and save them on

disk (੬ pg. 53), or transfer them to a VCR connected to the camcorder and record them onto a tape.

● When the Power Switch is set to “CAMERA” (“AUTO” or “PRO.”) and the LCD monitor is opened at an

angle of 60 degrees or more, the LCD monitor switches on and the viewfinder switches off automatically

to save power. When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may be

difficult to see. If this happens, we recommend that you use the viewfinder.

● When the remaining number indicator displays “0” (blinking), it is not possible to continue storing pictures

until you delete some shots to make room for new ones. Perform “DELETE” function in the Menu Screen

to remove pictures you do not need (੬pg. 58).

● The Picture Mode can be switched to either “FINE”or “STANDARD”. Since the remaining number of shots

available depends on the selected Picture Mode, switching the Picture Mode will vary this number.

● The LENS COVER warning blinks for approx. 5 seconds when the camcorder is turned on with the cover

closed.

● When SNAPSHOT is pressed with the System Select Switch set to “VIDEO”, the picture is stored in the

camcorder's built-in memory (in the Snapshot mode selected in the “VIDEO” system) and also onto the tape

(if a tape is in the camcorder) (੬ pg. 26).

● When you shoot in a dark environment, the still image will become coarse and its true colors will be lost.

RECORDING Basic Features

LENS COVER

Open/Close Ring

Snapshot

SNAPSHOT Button

This interesting feature lets you record two types of digital

still images that look like photographs onto a tape, as well

as keeping them in the camcorder’s built-in memory. It is a

great way to spice up footage of events such as parties,

weddings and graduations.

SNAPSHOT MODE SELECTION

SELECT OPERATION SYSTEM AND

1 _MODE

Turn the LENS COVER Open/Close Ring to open the

lens cover, and set the System Select Switch to

“VIDEO”. Set the Power Switch to “PRO.”

System Select Switch

MENU Button

•The power lamp lights and the camcorder enters

Record-Standby mode.

Power lamp

SELECT SNAPSHOT MODE

2 _{Press MENU. The Menu Screen appears.}

Rotate the Select Dial to move the highlight bar to

“SNAPSHOT”, and press it. SNAPSHOT Menu

appears.

Rotate the Select Dial to move the highlight bar to

“FULL” or “PIN-UP”, and press it. Selection is

complete.

Select Dial

Display

Power Switch

Menu Screen

CLOSE MENU SCREEN

3 _{The Menu Screen reappears with the highlight bar on}

M.W.B.

AUTO

D . ZOOM

“RETURN”. Then press the Select Dial to close the

Menu Screen.

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

FINE

SNAPSHOT

FULL

4RETURN

SNAPSHOT

SNAPSHOT Menu

FULL

PIN UP

EXIT

Menu Screen

M.W.B.

AUTO

D . ZOOM

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

FINE

PIN-UP

SNAPSHOT

4RETURN

(Pin-Up)

No display

(Full)

EN27

SNAPSHOT

SNAPSHOT RECORDING

TAKE SNAPSHOT

1 _{Press SNAPSHOT.}

Display (ex. Pin-Up)

•Regardless of the Power Switch position (“AUTO”

or “PRO.”), Snapshot recording takes place using

the selected Snapshot mode.

•A still image is recorded onto the tape and into the

camcorder’s built-in memory.

•First there is a momentary camera shutter-type

blackout together with the sound effect of a shutter

closing, then a still image appears. The scene you

are currently aimed at starts in the center of a black

screen and wipes in toward the corners.

The screen changes as shown in the illustrations 1

to 5 and the screens 1 to 5 are recorded onto the

tape in the selected mode. Only the still image 3 is

stored in the built-in memory in the selected mode,

then the camcorder resumes normal recording.

If you press during Record-Standby mode . . .

.... the screens 1 to 3 are recorded onto the tape in

the selected mode. Then the camcorder re-enters

the Record-Standby mode.

NOTES:

● When the remaining number indicator displays “0”

(blinking), the still image will be recorded onto the

tape but not in the built-in memory. If you wish to store

a still image in the built-in memory, ੬ pg. 58.

● The Picture Mode can be switched to either “FINE” or

“STANDARD”. Since the remaining number of shots

available depends on the selected Picture Mode,

switching the Picture Mode will vary this number.

● If SNAPSHOT is pressed with the System Select Switch

set to “D.S.C.”, ੬ pg. 22.

● Image data stored in the camcorder’s built-in memory

can be transferred to a Windows^®PC and saved using

the provided image transfer software, Picture Navigator

(੬ pg. 53). The image data transferred to a Windows^®

PC can also be further processed using Mr. Photo

Gold.

● If a snapshot is taken while the camcorder is in the

WIDE mode (੬ pg. 37), the snapshot image is

recorded without the black bars at the top and bottom

of the screen.

FULL

(Snapshot mode with

no frame)

● When a Snapshot is taken in a dark environment, the

still image recorded onto the tape and stored in

memory will become coarse and its true colors will be

lost.

PIN-UP

(Pin-Up mode)

RECORDING Basic Features (cont.)

FEATURE: Zooming

Zoom in

PURPOSE:

To produce the zoom in/out effect, or an instantaneous

change in image magnification.

Digital circuitry extends the maximum magnification

offered by optical zoom. This system is called Digital

Zoom.

Zoom out

OPERATION:

Zoom In

Push the Power Zoom Lever towards “T”.

Zoom Out

Display

Push the Power Zoom Lever towards “W”.

Ⅲ The quicker you push the Power Zoom Lever, the

quicker the zoom action.

Zoom indicator bar

Zoom level indicator

NOTES:

● Focusing may become unstable during Zooming. In

this case, set the zoom while in Record–Standby,

lock the focus by using the manual focus

(੬ pg. 41), then zoom in or out in Record mode.

● The zoom level indicator (5) moves during zoom.

Once the zoom level indicator reaches the top of

the zoom indicator bar, all magnification from that

point is through digital processing.

Approximate zoom ratio

Power Zoom Lever

● When using Digital Zoom, the quality of image may

suffer. To deactivate Digital Zoom, set “D.ZOOM”

to “OFF” in the Menu Screen (੬ pg. 37).

Power Switch

EN29

P. STABILIZER Button

FEATURE: Quick Review

PURPOSE:

To check the end of the last recording.

OPERATION:

1) Press “ ” and release quickly during the Record–

Standby mode.

Ⅲ Tape is rewound for about 2 seconds and played

back automatically, then pauses in Record–Standby

mode for the next shot.

NOTE:

Distortion may occur at the start of playback. This is

normal.

FEATURE: Retake

RETAKE (R/F) Button

PURPOSE:

To re-record certain segments.

OPERATION:

1) Make sure the camcorder is in the Record–Standby

mode.

2) Press either RETAKE to reach the start point for new

recording. Pressing “F” forwards the tape and

pressing “R” reverses it.

Display

3) Press the Recording Start/Stop Button to start

recording.

Picture stabilizer

indicator

NOTE:

Noise bars appear and pictures may become

monochrome or darken during Retake. This is normal.

FEATURE: Picture Stabilizer

PURPOSE:

To compensate for unstable images caused by camera-

shake, particularly at high magnification.

OPERATION:

1) Press P. STABILIZER. “

”appears.

Ⅲ To switch off the Picture Stabilizer, press

P. STABILIZER. The indicator disappears.

NOTES:

● Accurate stabilization may not be possible if hand

shake is excessive, or under the following conditions:

•When shooting subjects with vertical or horizontal

stripes.

•When shooting dark or dim subjects.

•When shooting subjects with excessive backlighting.

•When shooting scenes with movement in various

directions.

•When shooting scenes with low-contrast backgrounds.

● Switch off the Picture Stabilizer when recording

with the camcorder on a tripod.

● The “

” indicator appears blinking if the

Stabilizer cannot be used.

RECORDING Basic Features (cont.)

FEATURE: Video Light

PURPOSE:

To brighten the scene when natural lighting is too dim.

OPERATION:

1) Set the LIGHT OFF/AUTO/ON Switch as required:

OFF : Turns off the light.

AUTO : Automatically turns on the light when the

camcorder senses insufficient lighting on the

subject.

: Always keeps the light on as long as the

camcorder is turned on.

LIGHT OFF/AUTO/ON Switch

Ⅲ The video light can only be used with the

camcorder’s power on.

Ⅲ It is recommended to set the white balance

(੬ pg. 42) to

when you use the video light.

Ⅲ When not using the video light, turn it off to save

battery power.

DANGER

NOTES:

Ⅲ The video light can become extremely

hot. Do not touch it either while in

operation or soon after turning it off,

otherwise serious injury may result.

Ⅲ Do not place the camcorder into the

carrying case immediately after using the

video light, since it remains extremely

hot for some time.

● Even if the battery indicator (

) does not blink if

the battery pack’s charge is low, the camcorder may

turn off automatically when you turn on the video

light, or when you start recording with the video light

turned on.

● When the LIGHT OFF/AUTO/ON Switch is set to

“AUTO”:

Ⅲ When operating, keep a distance of

about 30 cm. (1 ft.) between the video

light and people or objects.

Ⅲ Do not use near flammable or explosive

materials.

Ⅲ It is recommended that you consult your

nearest JVC dealer for replacing the video

light.

•Depending on the lighting conditions, the video

light may keep turning on and off. In this case,

manually switch the light on or off using the

LIGHT OFF/AUTO/ON switch.

•While the “Sports” or “High Speed Shutter” mode

(੬ pg. 33) is engaged, the light is likely to stay on.

•While the “Twilight” mode (੬ pg. 33) is engaged,

the light will not activate.

RECORDING Advanced Features

EN31

[Ex.: Fader]

Fade in

Fade/Wipe

These effects let you make pro-style scene transitions.

Fade- or wipe-in works at recording start, and fade- or

wipe-out works at recording end or when you enter

Record–Standby mode.

SELECT OPERATION SYSTEM AND

1 _MODE

Fade out

Set the System Select Switch to "VIDEO", and set the

Power Switch to “PRO.”.

Display

EFFECT

After 2 sec.

ENGAGE FADE- OR WIPE-STANDBY

2 _MODE

MOSAIC

Press EFFECT to cycle through the modes as shown at

left. Once the desired mode appears, it is selected

and reserved.

EFFECT

MOSAIC

•The selected mode’s name and its indication are

displayed for approx. 2 seconds. Then the name

disappears, and only the indication remains.

START OR END RECORDING

FADER

MOSAIC

SHUTTER

SLIDE

3 _{Press the Recording Start/Stop Button to activate fade-}

in/out or wipe-in/out.

TO CANCEL FADE- OR WIPE-STANDBY

4 _MODE

Press EFFECT repeatedly until “OFF” appears.

•“OFF” is displayed for approx. 2 seconds and the

fade/wipe standby mode is canceled.

OFF

(No indication)

FADER

Fades in/out to a black screen.

System Select Switch

EFFECT Button

MOSAIC (Fader)

Gradually turns/returns the picture into/from a mosaic

pattern.

SHUTTER (Wipe)

A black screen moves in from the top and bottom, closing

over the image like a shutter, or a new image pushes open

the black screen vertically from the center.

SLIDE (Wipe)

A black screen moves in from the left to gradually cover

the image, or a new image moves in from right to left.

Recording Start/Stop

Button

Power Switch

NOTES:

● Pressing and holding the Recording Start/Stop Button allows you to vary the length for the image during fade

in/out or wipe in/out.

● The screen becomes slightly reddish when the Fade/Wipe is used with Sepia (੬ pg. 33).

● With the Electronic fog filter mode (੬ pg. 33) engaged, the image fades in/out to a white screen.

● Even if you start shooting with the Fade/Wipe indication displayed during Digital Still Camera Shooting, the

Fade/Wipe does not function.

RECORDING Advanced Features (cont.)

Display

P.AE

SEPIA

Program AE With Special Effects

After 2 sec.

All you have to do to access any of the variety of shooting

effects is press P.AE.

SELECT OPERATION SYSTEM AND

P.AE

1 _MODE

SEPIA

Set the System Select Switch to “D.S.C.” or “VIDEO”,

and set the Power Switch to “PRO.”.

SELECT MODE

2 _{Press P.AE to cycle through the modes as shown on}

the left.

SEPIA

•The selected mode’s name and its indication are

displayed for approx. 2 seconds. Then the name

disappears, and only the indication remains. The

mode is activated.

SPORTS

ND ND EFFECT

NOTES:

FG FOG

TWILIGHT

● Only one mode can be engaged at a time.

● The screen becomes slightly reddish when the Fade/

Wipe (੬ pg. 31) is used in the Sepia mode.

● The screen becomes slightly dark in the High Speed

Shutter mode. Use in well-lit situations.

S1/2000

● In the “High Speed Shutter” or “Sports” modes, picture

color may be adversely affected if the subject is lit by

alternating discharge-type light sources such as

flourescent or mercury-vapor lights.

NEGA/POSI

OFF

(No indication)

P.AE Button

Power Switch

System Select Switch

EN33

Display

Mode

Display

Mode

Sepia

Twilight

SEPIA

TWILIGHT

Sepia

Twilight

The scene being shot is recorded in sepia-tinted

(reddish-brown) monochrome, giving the effect of

an older movie. Use together with Wide (੬ pg. 37)

for the authentic look of a classic Hollywood

movie.

Dusk, twilight scenery, fireworks, etc., look more

natural and dramatic. The following happens when

Twilight mode is selected:

•Auto gain control is turned off.

•White Balance is set to “

” (FINE day mode),

•When the Power Switch is set to “D.S.C.”, the

scene is stored in black-and-white in the

camcorder’s memory.

but can also be manually changed to another

mode (੬ pg. 42).

•Auto Focus becomes available only in the range of

10 m (33 ft.) to infinity. To focus when the subject-

to-camera distance is less than 10 m (33 ft.), use

manual focusing (੬ pg. 41).

Sports

SPORTS

1/2000 sec.

High Speed Shutter

Sports

S1/2000

.)14

High shutter speed clearly captures fast-moving

action.

High-Speed Shutter (1/2000s.)

Captures faster action than Sports mode.

ND Effect

ND ND EFFECT

Nega/Posi

NEGA POSI

ND Effect

A black mist darkens the picture, as when an ND

filter is used. Helps to counter the effects of glare on

the subject.

Nega/Posi (Negative/Positive)

The colors of a picture are reversed.

Electronic

Fog Filter

FG FOG

Electronic Fog Filter

Makes the picture look misty white, as when an

external fog filter is attached to the lens. Softens the

image and gives it a “fantasy” look.

NEGA POSI mode

RECORDING Advanced Features (cont.)

Date/Time Insert

This feature allows you to display the date and time on the

LCD monitor, in the viewfinder, or on a connected color

monitor, as well as to record them manually or

automatically.

System

Select

Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “VIDEO”, and set the

Power Switch to “PRO.”.

ACCESS MENU SCREEN

2 _{Press the Select Dial to display the Menu Screen.}

ACCESS “DATE/TIME DISP.” MENU

3 _{Move the highlight bar to “DATE/TIME DISP.” by}

rotating the Select Dial while in Record-Standby.

Then press it to display the DATE/TIME DISP. Menu.

Select Dial

Display

Power Switch

Menu Screen

SELECT THE DESIRED MODE

4 _{Move the highlight bar to the desired mode by}

FOCUS

AUTO

OFF

rotating the Select Dial, then press it. The desired

mode is activated.

EXPOSURE

WIDE

S . LX

OFF

TITLE

DATE TIME DISP.

•You should have already performed the Date/Time

Setting procedure (੬ pg. 13). If you haven’t, do so

first.

RETURN

CLOSE MENU SCREEN

DATE TIME DISP.

5 _{The Menu Screen reappears with the highlight bar on}

DATE/TIME DISP.

AUTO DATE

DATE

“RETURN”. Then press the Select Dial to close the

Menu Screen.

TIME

DATE&TIME

OFF

NOTES:

DISPLAY

EXIT

● The selected display can be recorded.

● If you do not want to record the display, select the OFF

mode before shooting.

FOCUS

EXPOSURE

WIDE

AUTO

OFF

● Even if you shoot with the date/time displayed during

Digital Still Camera Shooting, they will not be recorded.

S . LX

OFF

TITLE

DATE TIME DISP.

AUTO DATE

● Your camcorder automatically records the date for about

5 seconds after recording is initiated in the following

situations:

RETURN

•After changing the date.

•After loading a cassette.

•After Auto Date Record mode is selected by rotating

the Select Dial.

● In this mode, the date is replaced after 5 seconds with

“AUTO DATE” but this is not recorded.

DEC 25 . 99

AUTO DATE

DEC 25 . 99

(DATE)

AM 10 : 25 : 00

(TIME)

DEC 25 . 99 AM 10 : 25 : 00

(DATE&TIME)

OFF

(No indication)

EN35

Instant Titles

The camcorder has eight preset titles in memory. You can

superimpose one of them above a previously stored title as

shown in the illustration to the left.

System

Select

Switch

Instant Titles can be displayed not only in English but also

in French, Spanish and Portuguese. Change the setting in

TITLE LANG. in the Menu Screen. (੬ pg. 36, 38).

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “VIDEO”, and set the

Power Switch to “PRO.”.

ACCESS MENU SCREEN

2 _{Press the Select Dial to display the Menu Screen.}

ACCESS “TITLE” MENU

3 _{Move the highlight bar to “TITLE” by rotating the}

Select Dial while in Record-Standby. Then press it to

display the TITLE Menu.

Select Dial

Display

AUTO

Power Switch

Menu Screen

SELECT THE DESIRED MODE

4 _{Move the highlight bar to the desired mode by}

rotating the Select Dial, then press it. The desired

mode is activated.

FOCUS

EXPOSURE

WIDE

AUTO

OFF

•If you wish to make the title indication disappear,

select “OFF”.

S . LX

TITLE

OFF

DATE TIME DISP.

CLOSE MENU SCREEN

RETURN

5 _{The Menu Screen reappears with the highlight bar on}

“RETURN”. Then press the Select Dial to close the

Menu Screen.

TITLE

TITLE Menu

OFF

HAPPY BIRTHDAY

OUR VACATION

MERRY CHRISTMAS

A SPECIAL DAY

HAPPY HOLIDAYS

OUR NEW BABY

WEDDING DAY

CONGRATULATIONS

EXIT

NOTE:

Even if you shoot with the Title displayed during Digital

Still Camera Shooting, this is not recorded.

FOCUS

EXPOSURE

WIDE

AUTO

OFF

S . LX

OFF

TITLE

DATE TIME DISP.

4RETURN

CONGRATULATIONS

RECORDING Advanced Features (cont.)

Using Menu For Detailed Adjustment

This camcorder is equipped with an easy-to-use,

on-screen menu system that simplifies many of the more

detailed camcorder settings.

System Select Switch

SELECT OPERATION SYSTEM AND MODE

1 _{The operation system depends on the function you wish}

to select.

Set the System Select Switch to “VIDEO” or “D.S.C.”

according to each function's “*/**” explanation

described at the bottom of pages 37 and 38, and set the

Power Switch to “PRO.”.

Select Dial

MENU Button

Menu Screen 1

ACCESS MENU SCREEN

Display

(ex. Menu Screen available

using the MENU Button)

2 _{Menu access depends on the function you select.}

If you select the functions from the “Menu Screen

Available Using The Select Dial” described on pg. 37 . . .

.... press the Select Dial. The Menu Screen appears.

M.W.B.

AUTO

If you select the functions from the “Menu Screen

Available Using The MENU Button” described on

pg. 37 and 38 . . .

D . ZOOM

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

.... press MENU. The Menu Screen appears.

PICTURE

FINE

FULL

SNAPSHOT

SELECT FUNCTION

RETURN

3 _{Rotate the Select Dial to place the highlight bar on the}

desired function.

Menu Screen 2

BACK

•To go from Menu Screen 1 to Menu Screen 2, rotate the

Select Dial to “NEXT” and press it. To go back to Menu

Screen 1 from Menu Screen 2, rotate the Select Dial to

“BACK”, and press it.

•If the setting you want cannot be found in the Menu Screen,

place the highlight bar on “RETURN”, then go to step 6.

REC. TIME

INT. TIME

OFF

TALLY LAMP ON

TITLE LANG. ENGLISH

JLIP ID NO

DEMO MODE OFF

RETURN

MAKE SETTING

4 _{Press the Select Dial. The setting procedure depends on}

the function you select.

TITLE LANG.

Setting Menu

(ex. TITLE LANG.)

If you select “FOCUS”, “EXPOSURE”, “TITLE”, “DATE/

TIME DISP.”, “DATE/ TIME”, “PICTURE” or "SNAP-

SHOT". . .

.... see respective pages (FOCUS: ੬ pg. 40, 41,

EXPOSURE: ੬ pg. 39, TITLE: ੬ pg. 35,

DATE/TIME DISP.: ੬ pg. 34, DATE/TIME: ੬ pg. 13,

PICTURE: ੬ pg. 24, SNAPSHOT: ੬ pg. 22, 27).

If you select “WIDE”, “D.ZOOM”, “TELE MACRO” or

“DEMO MODE” . . .

ENGLISH

FRENCH

SPANISH

PORTUGUESE

EXIT

.... the selected function’s parameter starts blinking.

Rotate the Select Dial until the desired parameter

appears. Go to step 5.

BACK

REC. TIME

INT. TIME

OFF

TALLY LAMP ON

If you select “JLIP ID NO.” . . .

TITLE LANG. FRENCH

JLIP ID NO

.... press the Select Dial so that the number blinks, then

rotate it until the desired number appears, and press

it. Then rotate the Select Dial to move the highlight

bar to “EXIT”.

DEMO MODE OFF

4RETURN

If you select any other functions . . .

.... rotate the Select Dial to move the highlight bar to the

desired setting.

Normal Screen

• If you decide you want to return to the previous setting,

rotate the Select Dial to move the highlight bar to “EXIT”.

END SETTING

NOTE:

5 _{Press the Select Dial. The Menu Screen reappears with}

No menu functions except “FOCUS” and

“EXPOSURE” are available while in the Record

mode.

the highlight bar on “RETURN”.

CLOSE MENU SCREEN

6 _{Press the Select Dial. The normal screen reappears.}

EN37

MENU SCREEN EXPLANATIONS

Menu Screen Available Using The Select Dial

Adjusts focus automatically.

FOCUS

AUTO

MANU

AUTO

MANU

OFF

Allows you to adjust focus manually (੬ pg. 40, 41).

Adjusts exposure automatically.

EXPOSURE

WIDE

Allows you to adjust exposure manually (੬ pg. 39).

Does not display black bars.

Allows you to record black bars at the top and bottom of the screen

to produce a cinema-like “wide-screen” effect.

If a snapshot (੬ pg. 22, 26) is taken while the camcorder is in

the WIDE mode, the snapshot image is recorded without the

black bars at the top and bottom of the screen.

To record a subject in a darkly lit environment, when it is more

convenient to shoot the subject with a brighter image even if the

picture becomes slightly coarse.

S.LX

MAX

To record a subject in a dimly lit environment, when it is more

convenient to shoot with a less coarse picture although the

subject becomes slightly dark. This setting is suitable for

measuring sensitivity conforming to EIA-639 (EIA* Standard for

Low Light Sensitivity Measurement).

NORMAL

*EIA : Electronic Industries Alliance

Allows you to shoot dark scenes with no picture brightness

adjustment.

OFF

TITLE*

Allows you to superimpose one of eight preset titles (੬ pg. 35).

DATE/TIME

DISP.*

Makes the date/time settings appear in the camcorder or on a connected monitor

(੬ pg. 34).

Menu Screen Available Using The MENU Button

This Menu Screen cannot be accessed while recording.

AUTO

: FINE

This camcorder’s Automatic Color Temperature system senses

the color temperature of the ambient lighting for automatic

white balance adjustment. However, precise color adjustment is

not possible under the following conditions:

M.W.B.

: CLOUD

• When an object is in various shades of the same color.

• When a predominantly red or brown object is being shot outdoors.

: HALOGEN

In these cases, use the camcorder’s built-in preset filters for

white balance adjustment (੬ pg. 42, 43).

MWB

D. ZOOM

Allows you to use the Digital Zoom. By digitally processing and

magnifying images, zooming is possible from 16 times (the optical

zoom limit), to a maximum of 380 times digital magnification.

OFF

Digital Zoom is not available. Only optical zoom (maximum

16x magnification) can function. When set to “OFF” during

Digital Zoom, zoom magnification changes to 16x.

* Activated only with the System Select Switch set to “VIDEO”. If the System Select Switch is set to “D.S.C.”,

this function will not be activated although the highlight bar will move on the Menu Screen like the setting

procedure.

Functions listed without an asterisk are available with the System Select Switch set to either “D.S.C.” or

“VIDEO”.

: Factory-preset

CONTINUED ON NEXT PAGE

RECORDING Advanced Features (cont.)

Menu Screen Available Using The MENU Button (cont.)

TELE MACRO

OFF

Usually the distance to a subject where the lens is in focus

depends on the zoom magnification. Unless there is a distance of

more than 1m (3.3 ft.) to the subject, the lens is out of focus at the

maximum telephoto setting. When set to “ON”, you can shoot a

subject as large as possible at a distance of approx. 60 cm (2 ft.).

•Depending on the zoom position, the lens may go out of focus.

DATE/TIME

Allows you to set the current date and time (੬ pg. 13).

TAPE LENGTH* Allows you to set the tape length depending on the tape used (੬ pg. 14).

Allows you to select the image setting “FINE” or “STD” when storing in the

camcorder's memory (੬ pg. 24).

PICTURE**

SNAPSHOT

FULL

Displayed with the System Select Switch set to either “VIDEO”

(੬ pg. 26) or “D.S.C.” (੬ pg. 23).

PIN-UP

MULTI-4

MULTI-9

M.DRIVE

Displayed only with the System Select Switch set to “D.S.C.”

(੬ pg. 23).

REC TIME*

INT. TIME

This feature allows you to set the parameters for Animation and Time-Lapse

recording (੬ pg. 45).

This feature allows you to set the parameters for Self-Timer (੬ pg. 44) and Time-

Lapse recording (੬ pg. 45).

TALLY LAMP*

OFF

The tally lamp remains off at all times.

The tally lamp comes on to signal the start of recording.

Allows you to select the language (ENGLISH, FRENCH, SPANISH or PORTUGUESE)

TITLE LANG.*

JLIP ID NO.

of Instant Titles (੬ pg. 35).

This number is necessary when connecting the camcorder to a device such as a computer

using the J terminal (JLIP). The numbers range from 01 to 99. Factory setting is 06.

Automatic demonstration will not take place.

DEMO MODE*

OFF

Demonstrates certain functions such as Fade/Wipe, etc. When

“DEMO MODE” is set to “ON” and the Menu Screen is closed,

the demonstration starts.

NOTES:

●When a tape whose Erase Protection tab is in the position that

allows recording is loaded in the camcorder, demonstration is

not available.

●By turning off the camcorder or inserting a tape whose Erase

Protection tab is in the position that allows recording into it,

“DEMO MODE” is set to “OFF” automatically.

●During the demonstration, all functions except zoom are

disabled.

* Activated only with the System Select Switch set to “VIDEO”. If the System Select Switch is set to “D.S.C.”,

this function will not be activated although the highlight bar will move on the Menu Screen like the setting

procedure.

** Activated only with the System Select Switch set to “D.S.C.”. If the System Select Switch is set to “VIDEO”,

this function will not be activated although the highlight bar will move on the Menu Screen like the setting

procedure.

Functions listed without an asterisk are available with the System Select Switch set to either “D.S.C.” or

“VIDEO”.

: Factory-preset

EN39

Exposure Control

This feature automatically adjusts the iris for the best

available picture quality, but you can override and make

the adjustment manually.

System

Select Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.” or “VIDEO”,

and set the Power Switch to “PRO.”.

ACCESS MENU SCREEN

2 _{Press the Select Dial to display the Menu Screen.}

ACCESS “EXPOSURE” MENU

3 _{Rotate the Select Dial to move the highlight bar to}

“EXPOSURE” and press it.

ACCESS MANUAL EXPOSURE

4 _{Rotate the Select Dial to move the highlight bar to}

Select Dial

Display

Power Switch

Menu Screen

“MANU”, then press it. “00” (exposure control level

counter) appears.

ADJUST EXPOSURE

5 _{To brighten the image . . .}

.... rotate the Select Dial upward. The exposure

control level counter increases (maximum +06).

FOCUS

AUTO

OFF

EXPOSURE

WIDE

S . LX

TITLE

OFF

Go to step 6.

To darken the image . . .

DATE TIME DISP.

.... rotate the Select Dial downward. The exposure

control level counter decreases (maximum –06).

4RETURN

Go to step 6.

EXPOSURE

EXPOSURE Menu

END ADJUSTMENT OF EXPOSURE

AUTO

MANU

6 _{Press the Select Dial. The Menu Screen reappears}

with the highlight bar on “RETURN”.

CLOSE MENU SCREEN

7 _{Press the Select Dial. The Menu Screen disappears}

EXIT

and the exposure control level counter reappers to

indicate the exposure is adjusted.

Manual Exposure

Screen

NOTES:

● To return to the factory setting, select “AUTO” in step 4.

● To re-adjust exposure, repeat the procedure from step 2.

Exposure control

level counter

To brighten the image

–06

To darken the image

RECORDING Advanced Features (cont.)

Focus detection zone

Focusing

AUTO FOCUS

The camcorder’s Full Range AF system offers continuous

shooting ability from close-up to infinity. However, correct

focus may not be obtainable in the situations listed below

(in these cases use manual focusing):

•When two subjects overlap in the same scene.

•When illumination is low.*

•When the subject has no contrast (difference in bright-

ness and darkness), such as a flat, one-color wall, or a

clear, blue sky.*

•When a dark object is barely visible in the viewfinder.*

•When the scene contains minute patterns or identical

patterns that are regularly repeated.

•When the scene is affected by sunbeams or light

reflecting off the surface of a body of water.

•When shooting a scene with a high-contrast background.

* The low-contrast warning “

” appears.

NOTES:

● If the lens is smeared or blurred, accurate focusing is not

possible. Keep the lens clean, wiping with a piece of soft

cloth if it gets dirty. When condensation occurs, wipe

with a soft cloth or wait for it to dry naturally.

● When shooting a subject close to the lens, zoom out first

(੬ pg. 28). If zoomed in in the auto focus mode, the

camcorder could automatically zoom out depending on

the distance between the camcorder and the subject.

When Tele Macro (੬ pg. 38) is activated, the

camcorder will not zoom out automatically.

EN41

MANUAL FOCUS

NOTE:

You should already have made the necessary viewfinder

adjustments (੬ pg. 16). If you haven’t, do so before

continuing.

System

Select Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.” or “VIDEO”,

and set the Power Switch to “PRO.”.

ACCESS MENU SCREEN

2 _{Press the Select Dial to display the Menu Screen.}

ACCESS “FOCUS” MENU

3 _{Move the hightlight bar to “FOCUS” by rotating the}

Select Dial, then press it.

ACCESS MANUAL FOCUS

Select Dial

Display

Power Switch

Menu Screen

4 _{Rotate the Select Dial to move the highlight bar to}

“MANU”, then press it. “ ” and “ ” appear. The

focus is locked at this point.

ADJUST FOCUS

FOCUS

AUTO

OFF

5 _{To farther subject . . .}

EXPOSURE

WIDE

.... rotate the Select Dial upward. “ ” appears and

S . LX

TITLE

OFF

blinks.

DATE TIME DISP.

Go to step 6.

To nearer subject . . .

4RETURN

.... rotate the Select Dial downward. “ ” appears

and blinks.

FOCUS

FOCUS Menu

Go to step 6.

AUTO

MANU

END ADJUSTMENT OF FOCUS

6 _{Press the Select Dial. The Menu Screen reappears}

with the highlight bar on “RETURN”.

EXIT

CLOSE MENU SCREEN

7 _{Press the Select Dial. The Menu Screen disppears and}

“

” reappears to indicate the focus is locked.

Manual Focus Screen

NOTES:

● To return to Auto Focus, select “AUTO” in step 4.

● To re-adjust Manual Focus, repeat the procedure from

step 2.

● Be sure to focus the lens in the maximum telephoto

position when you use the Manual Focus mode. If you

focus in on a certain subject in the wide-angle position,

sharply focused images cannot be obtained when

zoomed in because the depth-of-field is reduced at

longer focal lengths.

● When the focus level cannot be adjusted any farther or

closer, “ ” or “ ” will blink.

RECORDING Advanced Features (cont.)

White Balance Adjustment

A term that refers to the correctness of color reproduction

under various lighting. If the white balance is correct, all

other colors will be accurately reproduced.

System

Select Switch

The white balance is usually adjusted automatically.

However, the more advanced camcorder operator would

prefer to control this function manually and achieve a

more professional color/tint reproduction.

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.” or “VIDEO”,

and set the Power Switch to “PRO.”.

MENU Button

ACCESS MENU SCREEN

2 _{Press MENU. The Menu Screen appears.}

ACCESS WHITE BALANCE

3 _ADJUSTMENT

Move the highlight bar to “M.W.B.” by rotating the

Select Dial, then press it. The Menu Screen disap-

pears and the M.W.B. Menu appears.

Select Dial

Display

Power Switch

Menu Screen

SET FUNCTION PARAMETERS

4 _{Move the highlight bar to the required white balance}

by rotating the Select Dial.

M.W.B.

AUTO

D . ZOOM

“AUTO”

TELE MACRO OFF

DATE TIME

The white balance is adjusted automatically. This is

the factory preset position.

TAPE LENGTH T30

PICTURE

FINE

FULL

SNAPSHOT

“

: FINE”

When shooting outdoors on a sunny day.

: CLOUD”

When shooting outdoors on a cloudy day.

: HALOGEN”

RETURN

“

M.W.B.

M.W.B. Menu

AUTO

“

FINE

CLOUD

When using a video light or other similar type of

lighting.

HALOGEN

MWB

“MWB”

When shooting with the white balance already

having been set on the subject (੬ pg. 43).

EXIT

CLOSE MENU SCREEN

5 _{Press the Select Dial. The Menu Screen reappears}

with the highlight bar on “RETURN”. Press the Select

Dial again to close the Menu Screen.

To Return To Automatic White Balance . . .

.... select “AUTO” in step 4. Or set the Power Switch to

“AUTO”.

NOTE:

White balance cannot be used when Sepia (੬ pg. 33) is

activated.

EN43

Manual White Balance Operation

White paper

If the camera is operating in PRO. mode, perform a

Manual White Balance when shooting under various types

of lighting.

SELECT OPERATION SYSTEM AND

1 _MODE

Follow steps 1 through 4 of the white balance

adjustment (੬ pg. 42), and select “MWB”.

SET MANUAL WHITE BALANCE

2 _{Hold a sheet of plain white paper in front of the}

subject. Adjust zoom or position yourself so that the

white paper fills the screen.

System Select Switch

ENTER SETTING

3 _{Press the Select Dial until “MWB” begins blinking.}

•When the setting is completed, “MWB” stops

blinking, and the Menu Screen reappears with the

highlight bar on “RETURN”.

CLOSE MENU SCREEN

4 _{Press the Select Dial again to close the Menu Screen.}

Select Dial

Display

Power Switch

Menu Screen

To Change The Tint For Recording . . .

.... in step 2, substitute colored paper for white. The white

balance is adjusted based on the color, changing the

tint. Red paper — deeper green; blue paper — orange;

yellow paper — deeper purple.

M.W.B.

AUTO

D . ZOOM

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

PICTURE

FINE

FULL

SNAPSHOT

NOTES:

● In step 2, it may be difficult to focus on the white paper

in some circumstances. In such a case, adjust focus

manually (੬ pg. 41).

RETURN

M.W.B.

M.W.B. Menu

● A subject can be shot under various types of lighting

conditions indoors (natural, flourescent, candlelight,

etc.). Because the color temperature is different

depending on the light source, the tint of the subject will

differ depending on the white balance settings. Use this

function for a more natural result.

AUTO

FINE

CLOUD

HALOGEN

MWB

EXIT

● Once you adjust white balance during Manual White

Balance operation, the setting is retained even if the

power is turned off or the battery removed.

RECORDING Advanced Features (cont.)

Self-Timer

You can set the delay between pressing the Recording

Start/Stop button and the actual start of recording. If you

secure the camcorder, you (or whoever is operating the

camcorder) can enter the scene before recording starts.

System

Select Switch

NOTE:

Before performing the following steps, make sure that:

● The System Select Switch is set to “VIDEO” or “D.S.C.”

according to your needs.

● The Power Switch is set to “PRO.”.

● The camcorder is in the Record-Standby mode.

MENU Button

ACCESS MENU SCREEN

1 _{Press MENU.}

ACCESS “INT. TIME” MENU

2 _{Rotate the Select Dial to move the highlight bar to}

“NEXT” in Menu Screen 1 and press it to display

Menu Screen 2. Then, move the highlight bar to “INT.

TIME” and press it.

Select Dial

Display

Recording Start/Stop

Button

SET INTERVAL TIME

3 _{Rotate the Select Dial to move the highlight bar to the}

Menu Screen 1

desired time, then press it. The Menu Screen

reappears with the highlight bar on “RETURN”.

M.W.B.

AUTO

D . ZOOM

TELE MACRO OFF

DATE TIME

TAPE LENGTH T30

CLOSE MENU SCREEN

PICTURE

FINE

FULL

4 _{Press the Select Dial.}

SNAPSHOT

RETURN

START DELAYED RECORDING

5 _{If you set the System Select Switch to “VIDEO” . . .}

.... press the Recording Start/Stop Button. When the

selected time has elapsed, recording begins

automatically.

Menu Screen 2

4BACK

REC. TIME

INT. TIME

OFF

TALLY LAMP ON

TITLE LANG. PORTUGUESE

If you set the System Select Switch to “D.S.C.”. . .

.... press SNAPSHOT. When the selected time has

elapsed, a still image is shot automatically.

JLIP ID NO

DEMO MODE OFF

RETURN

To Cancel Self-Timer . . .

If you set the System Select Switch to “VIDEO” . . .

.... before the recording begins, press the Recording Start/

INT. TIME

REC TIME

OFF

1 4S

1 2S

1 S

15S

Stop Button to display “

TIME” in the Menu Screen to “OFF”.

”, then set “INT.

30S

1 MIN

5 MIN

5 S

If you set the System Select Switch to “D.S.C.” . . .

.... before shooting a still image, press SNAPSHOT, then

set “INT.TIME” in the Menu Screen to “OFF”.

EXIT

INT. TIME Menu

REC TIME Menu

INT. TIME indicator

REC TIME indicator

15S

INT. TIME and REC TIME indications on the normal

screen

EN45

You can record sequentially at preset time spans.

Leaving the camcorder aimed at a specific subject,

you can record subtle changes over an extended

period of time.

Animation

Time-Lapse

You can give stationary scenes or objects an illusion

of movement. This function allows you to shoot a

series of pictures, each slightly different, of the same

object for a brief period of time.

NOTE:

Before performing the following steps, make sure

that:

Before performing the following steps, make sure

that:

● The System Select Switch is set to “VIDEO”.

● The Power Switch is set to “PRO.”.

● The camcorder is in the Record-Standby mode.

● The recording mode is set to “SP”.

● The System Select Switch is set to “VIDEO”.

● The Power Switch is set to “PRO.”.

● The camcorder is in the Record-Standby mode.

● The recording mode is set to “SP”.

ACCESS MENU SCREEN

1 _{Press MENU.}

SET RECORDING TIME

SET INTERVAL BETWEEN

2 _{Rotate the Select Dial to move the highlight bar}2 _RECORDINGS

to “NEXT” in Menu Screen 1 and press it to

display Menu Screen 2. Then, move the

Rotate the Select Dial to move the highlight bar

to “NEXT” in Menu Screen 1 and press it to

display Menu Screen 2. Then, move the

highlight bar to “INT. TIME” and press it. The

INT. TIME Menu appears. Rotate the Select Dial

to move the highlight bar to the desired time,

then press it. The Menu Screen reappears.

highlight bar to “REC TIME” and press it. The

REC TIME Menu appears. Rotate the Select Dial

to move the highlight bar to the desired time,

then press it. The Menu Screen reappears with

the highlight bar on “RETURN”. Press the Select

Dial again to close the Menu Screen.

SET RECORDING TIME

START RECORDING

3 _{Rotate the Select Dial to move the highlight bar}

3 _{Press the Recording Start/Stop Button after}

to “REC TIME”, then press it. The REC TIME

Menu appears. Rotate the Select Dial to move

the highlight bar to the desired time, then press

it. The Menu Screen reappears with the

highlight bar on “RETURN”. Press the Select

Dial again to close the Menu Screen.

focusing on the subject. The recording stops

automatically after the selected period of time.

ASSEMBLE SERIES OF PICTURES

4 _{Repeat step 3 for the desired number of}

pictures.

START TIME-LAPSE RECORDING

RELEASE ANIMATION MODE

4 _{Press the Recording Start/Stop Button. Recording}

5 _{Set “REC TIME” in the Menu screen to “OFF”.}

and intervals alternate automatically.

RELEASE TIME-LAPSE MODE

NOTES:

5 _{To release when “}

” is displayed, set

● For best results, make sure the camcorder is

secured when shooting in Animation or Time-

Lapse mode.

“REC TIME” and “INT. TIME” in the Menu

Screen to “OFF”. To release when

“

” and “

press the Recording Start/Stop Button to display

”, then set “REC TIME” and “INT.

TIME” in the Menu Screen to “OFF”.

” are not displayed,

● Fade- or wipe-in/out cannot be performed during

Animation or Time-Lapse shooting.

“

● Before performing other operations following

Animation or Time-Lapse recording, make sure

the Animation or Time-Lapse mode is deactivated.

● Self-Timer, Animation and Time-Lapse are

canceled when the power is shut off or when the

cassette is ejected.

VIDEO PLAYBACK Basic Playback

LOAD A CASSETTE

Power lamp

1 _{First open the LCD monitor to an angle of over 60}

degrees. Slide EJECT to open the cassette holder, then

insert the cassette with the label facing out. Press

PUSH to ensure the holder is closed and locked.

Power Switch

SELECT OPERATION SYSTEM AND

2 _MODE

Make sure the LCD monitor is fully open. Set the

System Select Switch to “VIDEO”, and set the Power

Switch to “PLAY”.

System

Select

Switch

PLAY BACK

3 _{Press PLAY/PAUSE (}

4/6). The playback picture

appears.

STOP PLAYBACK

4 _{Press STOP (5).}

EJECT Switch

REW (2) Button

Rewind or Fast-Forward the tape

Press REW (2) to rewind, or FF (3) to fast-forward the

FF (3) Button

tape during Stop mode.

PLAY/PAUSE (4/6)

Button

NOTES:

● The camcorder shuts off automatically after about

5 minutes in Stop mode. To turn on again, set the Power

Switch to “POWER OFF”, then to “PLAY”.

STOP (5) Button

● When the Power Switch is set to “PLAY” and the LCD

monitor is opened at an angle of 60 degrees or more, the

LCD monitor switches on and the viewfinder switches

off automatically to save power.

LCD Monitor in Retracted Position

● The playback picture can also be viewed in the

viewfinder (with the LCD monitor shut) or on a

connected TV (੬ pg. 50, 51). Camcorder operation is

the same as described in this section.

● You can also view the playback picture on the LCD

monitor with it flipped over and retracted.

● If a blank portion on the tape is played back, the screen

may become black. This is not a malfunction.

Battery pack remaining power indicator

Tape counter

Recording mode indicator

Tape running

S ET SP

M 1 23 45

indicator

:Playback

:Fast-Forward/

Forward Search

:Rewind/Reverse

TAPE END

:Still Playback

VOLUNE

LCD monitor/viewfinder

indications

VIDEO PLAYBACK Features

EN47

Adjust the brightness of the LCD monitor

To brighten the image, turn the BRIGHT Dial towards “+”.

Speaker

To darken the image, turn the Dial towards “–”.

P.AE Button

EFFECT Button

NOTE:

The Bright Level Indicator is displayed under the Date/

Time Display when you play back images recorded in

Wide Mode (੬ pg. 37).

Power Zoom Lever

Speaker Volume Control

You can adjust the speaker volume by pushing the Power

Zoom Lever.

ADJUST VOLUME

1 _{If you want to turn up the volume . . .}

.... push the Power Zoom Lever towards “T”.

If you want to turn down the volume . . .

.... push the Power Zoom Lever towards “W”.

BRIGHT Dial

NOTE:

The Speaker Volume Indicator is displayed under the Date/

Time Display when you play back images recorded in

Wide Mode (੬ pg. 37).

Set to “VIDEO”.

Display

Tracking

This function can be used to eliminate noise bars that

appear on-screen during playback. Initial setting is Auto

Tracking. Manual Tracking is also available.

ACTIVATE MANUAL TRACKING

BRIGHT

1 _{Press P.AE and EFFECT simultaneously. Then, press}

P.AE or EFFECT as many times as necessary until the

noise bars disappear.

BRIGHT

•To return to Auto Tracking, press P.AE and EFFECT

simultaneously. “AT” blinks. When Auto Tracking

finishes, the indication disappears.

VOLUME

NOTES:

● When noise bars appear during playback, the

camcorder enters the Auto Tracking mode and “AT” is

displayed.

● Manual Tracking may not work with tapes recorded on

other VCRs or camcorders.

VIDEO PLAYBACK Features (cont.)

Power Switch

FEATURE: Still Playback

PURPOSE:

To pause during playback.

OPERATION:

1) Press PLAY/PAUSE (4/6) during playback.

2) To resume normal playback, press PLAY/PAUSE

(4/6) again.

Set to “VIDEO”.

NOTE:

Noise bars appear and pictures may become

monochrome during Still Playback. This is normal.

FEATURE: Shuttle Search

PURPOSE:

To allow high-speed search in either direction.

OPERATION:

1) Press FF (3) to search forward or press REW (2

to reverse during playback.

)

REW (2) Button

FF (3) Button

2) To resume normal playback, press PLAY/PAUSE

(4/6).

NOTES:

● During playback, press and hold REW (2) or

PLAY/PAUSE (4/6)

FF (3). The search continues as long as you hold

the button. Once you release it, normal playback

resumes.

Button

STOP (5) Button

● Noise bars appear and pictures may become

monochrome or darken during Shuttle Search. This

is normal.

COUNTER R/M Button

FEATURE: Counter Memory Function

PURPOSE:

To make it easier to locate a specific tape segment.

OPERATION:

1) Press COUNTER R/M and hold for more than

1 second. The counter resets to “0:00:00”.

2) Press COUNTER R/M for less than 1 second. “M”

appears.

3) After recording or playback, press STOP (5), then

REW (2). The tape automatically stops at or close

to 0:00:00.

4) Press PLAY/PAUSE (4/6) to start playback.

NOTES:

● The counter memory functions in the Fast-Forward

and Rewind modes.

● To disable the Counter Memory Function, press

COUNTER R/M for less than 1 second so that “M”

disappears.

VIDEO PLAYBACK Using The Cassette Adapter

Cassette Adapter (VHS Playpak)

EN49

Use this to play back a VHS-C video cassette recorded

with this camcorder on a VHS VCR. It is fully compatible

with any VHS video cassette recorder. The C-P7U adapter

is battery powered and automatically performs tape

loading and unloading.

INSERT BATTERY

1 _{Slide the battery cover up to remove it, and install}

one “AA(R6)” size battery as shown in the

illustration at left, then reattach the cover.

VCR

INSERT CASSETTE IN ADAPTER

2 _{Slide the latch to open the adapter compartment}

door, then insert the cassette and close the

compartment door.

Compartment door

PLAY BACK ON CONNECTED VCR

3 _{Load the cassette adapter into the VCR and play the}

tape back as you would any other.

REMOVE CASSETTE FROM ADAPTER

4 _{Slide the latch and the compartment door opens}

automatically. This may take around 10 seconds. Do

not attempt to force the adapter open. Then, insert

your finger in the hole on the underside of the

adapter as shown in the illustration at left, and push

up and remove the cassette.

Sliding latch

NOTES:

Compact video cassette

● During tape loading and unloading, do not touch the

reels for safety and tape protection.

● During special-effect playback (slow motion, still frame,

etc.), the picture may vibrate or noise bars may appear

on the screen.

Reels

● To record on a VCR using a compact cassette and the

adapter, cover the adapter’s recording safety hole with

adhesive tape.

Recording safety hole

PLAYBACK Basic Connections And Tape Dubbing

These are some basic types of connections. When making connections, refer also to your VCR and TV

instruction manuals.

Basic Connections

Use optional Video and Audio cables.

To Video Output

Video cable (optional)

To VIDEO IN

To AUDIO IN

To TV or VCR

Audio cable (optional)

To Audio Output

VCR

Connector cover*

Connection For Tape Dubbing

Use optional Video and Audio cables.

Power Switch

PLAY/PAUSE (4/6)

Button

To Video

Output

Video cable

(optional)

VIDEO IN

VCR (Recording deck)

Audio cable (optional)

To Audio Output

To AUDIO IN

Connector cover*

* When connecting the cables, open this cover.

EN51

Basic Connections

Tape Dubbing

CONFIRM POWER-OFF STATUS

CONNECT EQUIPMENT

1 _{Make sure the camcorder’s power is off.}

1 _{Following the illustration on pg. 50, connect the}

camcorder and the VCR.

CONNECT CAMCORDER TO TV OR

2 _VCR

PREPARE FOR DUBBING

2 _{Set the camcorder’s Power Switch to “PLAY”,}

Pull out the connector cover and open it.

turn on the VCR’s power, and insert the

appropriate cassettes in the camcorder and the

VCR.

Connect as shown in the illustration (੬ pg. 50).

If using a VCR . . . go to step 3.

If not . . . go to step 4.

SELECT VCR MODE

3 _{Engage the VCR’s AUX and Record-Pause}

CONNECT VCR OUTPUT TO TV

3 _INPUT

modes.

Refer to your VCR’s instruction manual.

FIND EDIT-IN POINT

4 _{Engage the camcorder’s Play mode to find a spot}

SUPPLY POWER

4 _{Turn on the camcorder, the VCR and the TV.}

just before the edit-in point. Once it is reached,

press PLAY/PAUSE (4/6) on the camcorder.

SELECT MODE

5 _{Set the VCR to its AUX input mode, and set the}

START EDITING

5 _{Press PLAY/PAUSE (}

TV to its VIDEO mode.

4/6) on the camcorder and

engage the VCR’s Record mode.

NOTES:

● It is recommended to use the AC Power Adapter/

Charger as the power supply instead of the battery

pack (੬ pg. 11).

STOP EDITING TEMPORARILY

6 _{Engage the VCR’s Record-Pause mode and press}

PLAY/PAUSE (4/6) on the camcorder.

● To monitor the picture and sound from the

camcorder without inserting a tape, set the

camcorder’s Power Switch to “CAMERA” (“AUTO”

or “PRO.”), then set your TV to the appropriate

input mode.

EDIT MORE SEGMENTS

7 _{Repeat steps 4 through 6 for additional editing,}

then stop the VCR and camcorder when

finished.

● Make sure you adjust the TV sound volume to its

minimum level to avoid a sudden burst of sound

when the camcorder is turned on.

● If you have a TV or speakers that are not specially

shielded, do not place the speakers adjacent to the

TV as interference will occur in the camcorder

playback picture.

NOTE:

If you wish to dub still images recorded with the

System Select Switch set to “D.S.C.”, play back the

still images (੬ pg. 52 – 56) instead of doing the

above steps 4 through 6, engage the VCR's Record

mode and record them onto a tape.

D.S.C. PLAYBACK Basic Playback

Still images shot using this camcoder are automatically

numbered, then stored in numerical order in the built-in

memory. You can view the still images stored in memory,

one at a time, much like flipping through a photo album.

System

Select Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.”, and set the

Power Switch to “PLAY”.

•The power lamp lights.

•The still image stored in memory is displayed.

•When no still image is stored in memory, the screen

becomes blue.

Power lamp

PLAY BACK

2 _{Press FF (}

3/PAGE+) or REW (2/PAGE–) to select

the still image you want to view.

•Each time REW (2/PAGE–) is pressed, the page

goes back, while each time FF (3/PAGE+) is

pressed, the page goes next.

Power Switch

•Even if you shoot a new picture after playing back a

still image with a low number, this will not

overwrite the existing picture because new pictures

are automatically stored after the still image most

recently stored in memory.

To move

the page next

Display

NOTES:

● When the Power Switch is set to “PLAY” and the LCD

monitor is opened at an angle of 60 degrees or more, the

LCD monitor switches on and the viewfinder switches

off automatically to save power.

● The playback picture can also be viewed in the

viewfinder (with the LCD monitor shut) or on a

connected TV (੬ pg. 50). Camcorder operation is the

same as described in this section.

● When viewing a playback picture on a connected TV, it

may jitter slightly.

● You can also view the playback picture on the LCD

monitor with it flipped over and retracted.

To move

the page back

D.S.C. PLAYBACK Connection

EN53

Connection to a Windows^®PC

Image data stored in the camcorder’s built-in memory can

be transferred to a Windows^®PC and saved using the

provided image transfer software, Picture Navigator. The

image data transferred to a Windows^®PC can also be

further processed using Mr. Photo Gold, and the still image

processed on the PC can be inserted onto a tape

(੬ pg. 63).

Set to “D.S.C.”

To assure safety, make sure all units are turned off before

making any connection.

To DIGITAL

connector

CONNECT TO PERSONAL

1 _COMPUTER

Connect the camcorder’s DIGITAL connector to the

COM Port (RS-232C) on a Windows^®PC, using the

provided PC connection cable.

PC connection cable

(provided)

SELECT OPERATION SYSTEM AND

2 _MODE

For Windows^®:

To COM Port

(RS-232C)

Set the System Select Switch to “D.S.C.”, then set the

Power Switch to “PLAY”.

•A still image stored in memory appears.

•When transferring still images to a computer, be

sure that a still image is displayed on the screen.

RUN IMAGE TRANSFER SOFTWARE

3 _{Launch the provided software on your Windows PC.}

Transfer the still images stored in the camcorder’s

memory to the Windows^®PC. Refer to the software’s

instruction manual on the provided CD-ROM for

details.

•During transfer of the still image, the camcorder’s

screen becomes blue and “

” is dis-

Display

played. After transferring is finished, the screen

displays the same still image as in step 2.

END TRANSFERRING

4 _{Close the software, then switch off the camcorder.}

PC MODE

NOTES:

● Before transferring still images from your personal computer to the camcorder’s built-in memory, perform the

camcorder’s Picture Mode Setting (੬ pg. 24). The still images will be transferred from the personal

computer in the selected Picture Mode.

● When transferring still images from your personal computer to the camcorder, make sure the number of

images to be transferred is smaller than the camcorder's remaining number of shots available.

● Use the AC Power Adapter/Charger as the power supply instead of the battery pack.

● The still images stored in the camcorder’s memory are not automatically removed after being transferred to

the PC. If you wish to remove those still images from the camcorder's memory, delete them (੬ pg. 58, 59).

● Windows^®are trademarks of Microsoft Corporation, registered in the U.S.A. and other countries.

D.S.C. PLAYBACK Advanced Features

Using Menu For Detailed Adjustment

This camcorder is equipped with an easy-to-use,

on-screen menu system that simplifies many of the more

detailed camcorder settings.

System

Select Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.”, and set the

Power Switch to “PLAY”.

ACCESS MENU SCREEN

2 _{Press MENU. The Menu Screen appears.}

MENU Button

SELECT FUNCTION

3 _{Rotate the Select Dial to place the highlight bar on}

the desired function.

•If the setting you want cannot be found in the Menu

Screen, place the highlight bar on “RETURN”, then

press the Select Dial.

Select Dial

Power Switch

Menu Screen

MAKE SETTING

4 _{Press the Select Dial. The setting menu of the selected}

Display

function appears. The setting procedure depends on

the function you select.

INDEX

If you select “SLIDE SHOW 1” or “SLIDE SHOW 2” . . .

SLIDE SHOW 1

SLIDE SHOW 2

PROTECT

.... a slide-show will start (੬ pg. 55).

DELETE

If you select any other functions . . .

.... see respective pages (INDEX: ੬ pg. 56,

PROTECT: ੬ pg. 57, DELETE: ੬ pg. 58, 59)

and do each procedure from step 4.

4RETURN

^EXIT<PROTECT>

Setting Menu

(ex. PROTECT)

INDEX

SLIDE SHOW 1

SLIDE SHOW 2

PROTECT

DELETE

4RETURN

Normal Screen

EN55

Menu Screen Explanations

Mode

Effect

INDEX

All still images stored in memory can be displayed six at a time. This mode is a

convenient way to look for the still image you want to view and to check the still

images you shot beforehand (੬ pg. 56).

SLIDE SHOW 1

After doing steps 1 through 4 on pg. 54, you can run through all the still images

stored in memory automatically in numerical order. Each still image is displayed.

This mode is like a regular slide-show. If you wish to stop the slide-show, press the

Select Dial twice.

SLIDE SHOW 2

After doing steps 1 through 4 on pg. 54, you can run through all the still images

stored in memory automatically in numerical order. The still image wipes in over

the last one from the bottom of the screen to the top. If you wish to stop the slide-

show, press the Select Dial twice.

PROTECT

DELETE

Lets you protect selected still images from accidental erasure. Select a still image for

which you want to perform “Protect” to put a padlock mark next to it. A still image

with a padlock mark cannot be deleted. When selecting a still image to protect, you

can check six still images stored in memory at a time (੬ pg. 57).

Allows you to delete some still images already stored in memory (੬ pg. 58).

CAUTION:

While “ENTER” is selected on the Delete Execute Menu and it is blinking, switching

off the camcorder or removing the power supply unit (battery pack or AC Power

Adapter/Charger) may cause the camcorder’s built-in memory to become corrupt.

Never remove the power supply unit at this stage.

SELECT

Allows you to check 6 still images stored in memory at a time, to select

the still images you want to delete.

ALL

Allows you to delete all the still images at once except protected

images.

D.S.C. PLAYBACK Advanced Features (cont.)

Index

You can view all still images stored in memory six at a

time. Use this mode when looking for a still image you

want to view and when checking the still images you shot

beforehand.

System

Select Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.”, and set the

Power Switch to “PLAY”.

ACCESS MENU SCREEN

MENU Button

2 _{Press MENU. The Menu Screen appears.}

ACCESS “INDEX” MENU

3 _{Rotate the Select Dial to move the highlight bar to}

“INDEX” and press it. The “INDEX” Menu appears.

VIEW INDEX IMAGES

4 _{Rotate the Select Dial to move the frame to the}

Select Dial

Power Switch

desired still image, then press it. The one you selected

is displayed on the whole screen, then the screen

enters normal playback.

Display

•On the INDEX Menu, 6 still images are displayed at

a time. When viewing the still images that follow

the 6th one, rotate the Select Dial to move the

frame from Index No. 1 to No. 6, and then rotate it

further downward. The frame is placed on the 7th

still image automatically. Images after the 7th one

can also be accessed in the same way.

Menu Screen

INDEX

SLIDE SHOW 1

SLIDE SHOW 2

PROTECT

DELETE

4RETURN

•If the desired still image cannot be found, place the

highlight bar on “EXIT”, then press the Select Dial

twice to exit the Menu.

EXIT

<INDEX>

INDEX Menu

NOTES:

● When moving the frame from the 7th still image back to

the 6th, rotate the Select Dial upward to place the

highlight bar on “EXIT”, then rotate it further upward.

The frame is moved to the 6th still image. Perform the

same procedure for the 13th image.

● On the INDEX Menu, a star mark is displayed next to a

still image you shot in the FINE mode.

Playback Screen

EN57

Protect

This mode helps prevent accidental erasure of images. Put

a padlock mark next to the desired still image, and that still

image cannot be deleted.

System

Select Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.”, and set the

Power Switch to “PLAY”.

ACCESS MENU SCREEN

2 _{Press MENU. The Menu Screen appears.}

MENU Button

ACCESS “PROTECT” MENU

3 _{Rotate the Select Dial to move the highlight bar to}

“PROTECT”, and press it. The PROTECT Menu

appears.

•If you do not want to perform “Protect” for any still

image, go to step 5.

Select Dial

Power Switch

Menu Screen

SET PROTECT

4 _{Rotate the Select Dial to move the frame to the}

Display

desired still image, then press it. The padlock mark

appears above the selected image.

INDEX

SLIDE SHOW 1

SLIDE SHOW 2

PROTECT

•On the PROTECT Menu, all still images are

displayed six at a time. To perform “Protect” for the

still images that come after the 6th one, rotate the

Select Dial to move the frame from Index No. 1 to

No. 6, then rotate it further downward. The frame is

placed automatically on the 7th still image. Images

after the 7th one can also be accessed in the same

way.

DELETE

4RETURN

^EXIT<PROTECT>

PROTECT Menu

•To complete “Protect”, go to step 5.

CLOSE MENU SCREEN

5 _{Rotate the Select Dial upward to place the highlight}

bar on “EXIT”, then press it twice.

To remove “Protect” . . .

^EXIT<PROTECT>

.... perform steps 1 through 3, rotate the Select Dial to

move the frame to the desired still image with the

padlock mark, then press it. The padlock mark located

above the still image disappears and the image is no

longer protected. When finished removing protection,

perform step 5.

A padlock mark

appears.

NOTES:

● To move the frame from Index No. 7 to 6, place the

highlight bar on “EXIT” by rotating the Select Dial

upward. Rotate the Select Dial further upward. The

frame is moved to the 6th still image automatically.

Perform the same procedure for still images that follow

the 13th one.

● On the PROTECT Menu, a star mark is displayed next to

a still image you shot in the FINE mode.

D.S.C. PLAYBACK Advanced Features (cont.)

Delete

When the memory in which still images are stored

becomes full, the number of remaining shots available

reaches “0” (blinking). In this situation it becomes

impossible to take your next shot. Delete some still images

already stored in memory to make room for new shots.

System

Select Switch

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “D.S.C.”, and set the

Power Switch to “PLAY”.

MENU Button

ACCESS MENU SCREEN

2 _{Press MENU. The Menu Screen appears.}

ACCESS “DELETE” MENU

3 _{Rotate the Select Dial to move the highlight bar to}

“DELETE”, and press it. The DELETE Menu appears.

SELECT DELETE MODE

Select Dial

Power Switch

4 _{Rotate the Select Dial to move the highlight bar to}

“SELECT” or “ALL”, then press it.

To select a still image by checking the still images

stored in memory . . .

Display

Menu Screen

INDEX

.... select “SELECT”, then go to step 5.

To delete all the still images stored in memory at

once without checking them . . .

SLIDE SHOW 1

SLIDE SHOW 2

PROTECT

DELETE

.... select “ALL”, then go to step 6.

To quit the Delete Mode . . .

.... rotate the Select Dial to place the highlight bar

on “EXIT”, then press it twice.

4RETURN

DELETE

DELETE Menu

SELECT ON DELETE SELECT MENU

SELECT

ALL

5 _{Rotate the Select Dial to move the frame to the}

desired still image, then press it. “ ” appears above

the selected still image. When you have finished

selecting all the desired still images, rotate the Select

Dial upward to place the highlight bar on “NEXT”,

then press the Select Dial.

In case of “ALL”

EXIT

^NEXT<DELETE>

•On the Delete Select Menu, the still images are

displayed six at a time. To delete the still images

that follow the 6th one, rotate the Select Dial to

move the frame from No. 1 to No. 6, then rotate it

further downward. The frame is moved to the 7th

still image automatically. Perform the same

In case of

“SELECT”

procedure for still images that follow the 7th one.

Delete Select Menu

DELETE

CANCEL

ENTER

Delete Execute Menu

Menu Screen

EN59

In case of “SELECT”

ACCESS DELETE EXECUTE MENU

6 _{Rotate the Select Dial to move the highlight bar to}

NEXT <DELETE>

“CANCEL” or “ENTER”, then press it.

•“CANCEL” does not delete the selected still images

and the screen returns to the Menu Screen.

•“ENTER” deletes the selected still images. While

“ENTER” blinks, they are in the process of being

deleted from memory. After deleting is finished, the

screen returns to the Menu Screen.

CLOSE MENU SCREEN

7 _{Press the Select Dial again to exit the Menu Screen.}

CAUTION:

If you check the remaining still images on

INDEX Menu after deleting...

While “ENTER” is selected on the Delete

Execute Menu and it is blinking, switching off

the camcorder or removing the power supply

unit (battery pack or AC Power Adapter/Charger)

may cause the camcorder’s built-in memory to

become corrupt. Never remove the power

supply unit at this stage.

EXIT

<INDEX>

NOTES:

● Before deleting some still images stored in memory,

perform “Protect” for the necessary ones (੬ pg. 57) or

save them on a PC so that you do not lose them

accidentally (੬ pg. 53).

● Even if “ALL” is selected on the DELETE Menu, it is not

possible to delete a still image with a padlock mark.

“ALL” only deletes all still images that are not protected.

After images are deleted from memory, the remaining

images are automatically moved up to fill in any gaps in

the numerical sequence. The Index No. for images

protected (with the padlock mark) may therefore change.

● When selecting the desired still image in step 5, to move

the frame from No. 7 to 6, place the highlight bar on

“EXIT” by rotating the Select Dial upward. Rotate it

further upward to move the frame to No. 6. Perform the

same procedure for still images that follow the 13th one.

● On the Delete Select Menu, a star mark is displayed next

to a still image you shot in the FINE mode.

● If the remaining number of shots is not 30 in the FINE

mode or 60 in the STANDARD mode when “ALL” is

selected on the DELETE Menu, initialize the camcorder’s

memory (੬ pg. 68).

USING THE REMOTE CONTROL UNIT

The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic

operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR.

Installing The Battery

The remote control uses one lithium battery

(CR2025).

PULL OUT BATTERY HOLDER

1 _{Pull out the battery holder by inserting a pointed}

instrument into the slot.

INSERT BATTERY IN HOLDER

2 _{Insert the battery in the holder, and be sure to}

have the “+” mark visible.

Slot

RE-INSERT HOLDER

3 _{Slide the holder back in until you hear a click.}

•Read the caution concerning lithium batteries

(੬ pg. 2).

RM-V705U

(provided)

Functions

Buttons

With the camcorder’s Power Switch set

to “CAMERA”, “AUTO” or “PRO.”

With the camcorder’s Power Switch

set to “PLAY”.

1 Infrared beam

Transmits the beam signal.

transmitting window

2 ZOOM (T/W) Buttons

3 PLAY Button

Zoom in/out (੬ pg. 28)

—

Playback start (੬ pg. 46)

Stop (੬ pg. 46)

—

4 STOP Button

5 REW Button

Retake (rewind)/Quick Review

(੬ pg. 29)

Rewind, Reverse Shuttle Search

(੬ pg. 46, 48)

6 INSERT Button

7 START/STOP Button

8 INT. TIME Button

9 REC TIME Button

0 PAUSE Button

! FF Button

—

Insert Editing (੬ pg. 62, 63)

Functions the same as the Recording Start/Stop Button on the camcorder.

Self-Timer/Time-Lapse (੬ pg. 61)

Animation/Time-Lapse (੬ pg. 61)

—

Pause (੬ pg. 48)

Retake (forward) (੬ pg. 29)

Fast-Forward, Forward Shuttle Search

(੬ pg. 46, 48)

@ A.DUB Button

—

Audio dubbing (੬ pg. 64)

EN61

FEATURE: Self-Timer, Animation and

Time-Lapse

Transmitted beam

effective area

PURPOSE:

The remote control lets you set/release Interval Timer

and Rec Time functions without using the Menu

Screen.

OPERATION:

Remote sensor

Self-Timer

1) Set

Instead of performing steps 1 through 4 on pg. 44

(“Self-Timer”), press INT. TIME on the remote

control. Each time INT. TIME is pressed, the Interval

Timer indicator appears, changing in the following

order: 15S, 30S, 1MIN, 5MIN and No indication

(off).

When using the remote control, be sure to point it at

the remote sensor. The above illustration shows the

approximate transmitted beam effective area for

indoor use.

The transmitted beam may not be effective or may

cause incorrect operation outdoors or when the

remote sensor is directly exposed to sunlight or

powerful lighting.

2) Release

Instead of setting “INT. TIME” to “OFF” in the Menu,

press INT. TIME on the remote control until the

Interval Timer indicator disappears.

Animation

Interval timer indicator

1) Set

Instead of performing steps 1 and 2 on pg. 45

(“Animation”), press REC TIME on the remote

control. Each time REC TIME is pressed, the Rec

Time indicator appears, changing in the following

order: 1/4S, 1/2S, 1S, 5S and No indication (off).

2) Release

1MIN

INDEX

Instead of using the Menu in step 5 on pg. 45, press

REC TIME on the remote control until the Rec Time

indicator disappears.

Rec time indicator

Time-Lapse

1) Set

Instead of performing steps 1 through 3 on pg. 45

(“Time-Lapse”), press INT. TIME and REC TIME on

the remote control. Each time INT. TIME is pressed,

the Interval Timer indicator appears, changing in the

following order: 15S, 30S, 1MIN, 5MIN and No

indication (off). Each time REC TIME is pressed, the

Rec Time indicator appears, changing in the

following order: 1/4S, 1/2S, 1S, 5S and No indication

(off).

Remote sensor

2) Release

Instead of using the Menu in step 5 on pg. 45, press

INT. TIME and REC TIME on the remote control until

the indicators disappear.

NOTE:

Also refer to pgs. 44 and 45.

START/STOP

INT. TIME

REC. TIME

RM-V705U

(provided)

USING THE REMOTE CONTROL UNIT (cont.)

Insert Editing (VIDEO)

Power Switch

You can record a new scene onto a previously recorded

tape, replacing a section of the original recording with

minimal picture distortion at the in- and out-points. The

original audio remains unchanged.

System Select Switch

NOTE:

Use the RM-V705U remote control unit to perform this

procedure.

SELECT OPERATION SYSTEM AND

1 _MODE

Set the System Select Switch to “VIDEO”, and set the

Power Switch to “PLAY”.

REW (2) Button

FIND EDIT-OUT POINT

2 _{Play back the tape, locate the point and press PAUSE}

FF (3) Button

PLAY/PAUSE (4/6) Button

on the camcorder or the remote control.

RESET COUNTER

STOP (5) Button

3 _{Press and hold COUNTER R/M for more than}

1 second to reset the tape counter, then press again

for less than 1 second so that “M” appears.

COUNTER R/M Button

FIND EDIT-IN POINT

Display

4 _{Press REW to go a little beyond the beginning of the}

Insert editing

indicator

scene you want to replace, press PLAY to view the

recorded tape, and press PAUSE exactly at the

point where the new scene should start.

Tape Counter

Remote sensor

M 0 12 34

ENGAGE INSERT EDITING MODE

5 _{Press and hold INSERT, and without releasing}

INSERT, press and release PAUSE. The Insert Editing

standby mode is engaged. The Insert Editing Indicator

is displayed on the top left corner of the LCD monitor

or viewfinder. When the scene the camcorder is

aimed at appears on the screen, go to the next step.

BEGIN INSERT EDITING

6 _{Press START/STOP. When the counter reaches}

“0:00:00”, editing stops automatically and the

camcorder enters the Insert-Pause mode.

END INSERT EDITING

7 _{Press STOP.}

NOTES:

● During Insert Editing, the original audio will be heard

from the speaker.

START/STOP

● After step 5, Retake (੬ pg. 29) can be performed.

● The tape may stop slightly before or after the designated

end point, and noise bars may appear. Neither indicates

a defect in the unit.

● Only the video signal is recorded in the Insert Editing

mode.

PLAY

STOP

PAUSE

REW

INSERT

RM-V705U

(provided)

EN63

Insert Editing (Insert A Still Image From

Power Switch

The Built-in Memory Onto A Tape)

You can insert a still image stored in the camcorder's built-

in memory into a previously recorded tape, replacing a

section of the original recording with minimal picture

distortion at the in- and out-points. The original audio

remains unchanged.

System Select Switch

Perform steps 1 through 5 in Insert Editing (VIDEO)

(੬ pg. 62) before the following procedure.

NOTE:

Use the RM-V705U remote control unit to perform this

procedure.

SELECT STILL IMAGE

REW (2/PAGE–) Button

1 _{First set the System Select Switch to “D.S.C.”. Press}

FF (3/PAGE+) Button

PLAY/PAUSE (4/6) Button

REW (2/PAGE–) or FF (3/PAGE+) to select the

still image you wish to insert.

BEGIN INSERT EDITING

STOP (5) Button

2 _{Press START/STOP. When the counter reaches}

“0:00:00”, editing stops automatically and the

camcorder enters the Insert-Pause mode.

COUNTER R/M Button

To insert still images in sequential order onto the

tape . . .

Display

... press REW (2/PAGE–) or FF (3/PAGE+) to

move the page forward.

Insert editing

indicator

To insert still images at random onto the tape . . .

... first record the still image you selected in step 1

onto the tape, then press START/STOP to engage

the Insert-Pause mode. To select another still

M 0 12 34

Tape counter

image, press REW (2/PAGE–) or FF (3

PAGE+) again, then press START/STOP. Insert-

Editing begins.

Remote sensor

END INSERT EDITING

3 _PressSTOP.

NOTES:

● The tape may stop slightly before or after the designated

end point, and noise bars may appear. Neither indicates

a defect in the unit.

● Only video signal is recorded in the Insert Editing mode.

START/STOP

PLAY

STOP

PAUSE

REW

INSERT

RM-V705U

(provided)

USING THE REMOTE CONTROL UNIT (cont.)

Display

Audio Dubbing

Audio dubbing

indicator

You can record a new soundtrack on a prerecorded tape

M 0 05 20

(normal audio only).

Perform steps 1, 2 and 3 of the Insert Editing procedure

(੬ pg. 62) before continuing.

•The sound comes from the built-in microphone.

FIND EDIT-IN POINT

1 _{Press REW to go a little beyond the beginning of the}

scene onto which you want to dub the new audio,

press PLAY to view the recorded tape, then press

PAUSE at exactly the point where dubbing should

start.

Remote sensor

Microphone

ENGAGE AUDIO DUB-STANDBY MODE

2 _{Press and hold A. DUB, and without releasing}

A. DUB, press and release PAUSE. The Audio Dub

standby mode is engaged. The Audio Dubbing

Indicator is displayed on the top right corner of the

LCD monitor or viewfinder.

BEGIN AUDIO DUBBING

3 _{Press PLAY. When the counter reaches “0:00:00”,}

Audio Dubbing stops automatically and the

camcorder enters the Audio Dub-Standby mode.

END AUDIO DUBBING

4 _PressSTOP.

Set to “VIDEO”

PLAY

PAUSE

STOP

REW

NOTES:

● Do not press FF or REW during Audio Dub-Standby, or

the edit points will not be accurate.

● If the microphone is too close to the TV, or if the TV’s

volume is too high, whistling or howling may occur.

A. DUB

RM-V705U

(provided)

NOTES (for Insert Editing and

Audio Dubbing):

● Insert Editing and Audio Dubbing may not work

correctly if the tape contains blank segments, or if the

recording speed was changed during the original

recording.

● To edit/dub onto a tape, make sure the Erase Protection

tab is in the position that allows recording. If not, slide

the tab. Some cassettes have removable tabs. If the tab

has been removed, cover the hole with adhesive tape.

● Do not press STOP during Insert Editing or Audio

Dubbing, or the edit points will not be accurate.

● During Insert Editing and Audio Dubbing, when Insert-

Pause or Audio Dub-Standby is engaged, the counter

may go slightly past “0:00:00”. Recording, however,

stops at exactly 0:00:00.

USER MAINTENANCE

EN65

LENS COVER Open/Close Ring

After Use

Set the Power Switch to “POWER OFF” to turn off

1 _{the camcorder.}

Open the LCD monitor to an angle of over 60

2 _{degrees. Slide EJECT to open the cassette holder, then}

remove the cassette.

Close and lock the cassette holder by pressing PUSH.

Close and lock the LCD monitor.

BATTERY RELEASE

Set to “POWER OFF”.

Slide BATTERY RELEASE to remove the battery pack.

Turn the LENS COVER Open/Close Ring to close

6 _{the lens cover.}

Cleaning The Camcorder

CLEAN EXTERIOR

1 _{Wipe gently with a soft cloth.}

Remove.

•Put cloth in diluted mild soap and wring it well to

wipe off heavy dirt, then wipe again with a dry

cloth.

PUSH

EJECT

CLEAN LCD MONITOR

2 _{Open the LCD monitor and wipe it gently with a soft}

cloth. Be careful not to damage the monitor. Close

the LCD monitor.

CLEAN LENS

3 _{Blow it with a blower brush, then wipe it gently with}

lens cleaning paper.

REMOVE EYEPIECE

4 _{Turn the eyepiece counterclockwise and pull it out.}

CLEAN VIEWFINDER

5 _{Remove dust using a blower brush.}

RE-ATTACH EYEPIECE

6 _{Re-attach the eyepiece and turn it clockwise.}

NOTES:

● Avoid using strong cleaning agents such as benzine or alcohol.

● Cleaning should be done only after the battery pack has been removed or other power units have been

disconnected.

● Mold may form if the lens is left dirty.

● When using a cleaner or chemically treated cloth, refer to the cautions that came with it.

● When removing the eyepiece, be sure to hold the viewfinder securely.

TROUBLESHOOTING

If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might

prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power

Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and proceed as usual from the beginning.

SYMPTOM

POSSIBLE CAUSE(S)

POWER

No power is supplied.

● The battery pack has not been attached correctly (੬ pg. 10).

● The battery pack is not charged (੬ pg. 10).

●

The power supply has not been correctly connected (

੬

pg. 11).

The power suddenly goes off and

does not come back on by itself.

● The battery pack has completely discharged.

● Remove the cassette and disconnect the power source, then

after a few minutes, try turning the power back on. If it still

doesn’t come on, consult your nearest JVC dealer.

OTHER

Some functions are not available.

● The Power Switch is set to “AUTO”.

●

Certain combinations of modes or effects are not possible to use.

● Press DISPLAY for longer than 1 second to make the

indications appear (੬ pg. 19).

During recording, the indications do

not appear.

Vertical white lines appear when

shooting a very bright object.

●

This sometimes occurs when the contrast between the back-

ground and the object is great. It is not a defect of the camcorder.

Bright, crystal-shaped spots appear in

the LCD monitor and the viewfinder.

● Sunlight is directly entering the lens. This is not a defect of

the camcorder.

The rear of the LCD monitor is hot.

● The light used to illuminate the LCD monitor causes it to be

hot. Close the LCD monitor to turn it off or set the power

switch to “OFF”, and let the unit cool down.

Colored bright spots appear all over

the LCD monitor or the viewfinder.

●

The LCD monitor and the viewfinder are made with high-precision

technology. However, black spots or bright spots of light (red, green

or blue) may appear constantly on the LCD monitor or in the

viewfinder. These spots are not recorded on the tape. This is not

due to any defect of the unit. (Effective dots: more than 99.99 %.)

The indicators and the picture color

on the LCD monitor are not clear.

● This may occur when the surface or the edge of the LCD

monitor is pressed.

The LCD monitor, the viewfinder and

the lens have become dirty (ex.

fingerprints).

● Wipe them gently with soft cloth. Gently wipe the LCD

monitor in a semicircle because wiping strongly spreads the

stain and it won’t come out easily.

An error number (i.e. E03) appears.

●

Turn the camcorder’s power off, then disconnect the power

source. After a few minutes, try turning the power on again. If

the error number still appears, consult your nearest JVC dealer.

The image is out of focus.

● The diopter needs to be adjusted (੬ pg. 16).

● The scene being shot is adversely affecting the operation of

Auto Focus (੬ pg. 40).

● The Lens Cover Warning indicator may blink when the

camcorder is used in dark areas, regardless of the position

of the Lens Cover.

Even though the Lens Cover is open,

the Lens Cover Warning indicator

blinks.

TROUBLESHOOTING (cont.)

When the System Select Switch is set to “VIDEO”:

EN67

SYMPTOM

POSSIBLE CAUSE(S)

RECORDING

Recording cannot be performed.

● Make sure the Erase Protection tab is in the position that

allows recording. If not, slide the tab. Some cassettes have

removable tabs. If the tab has been removed, cover the

hole with adhesive tape (੬ pg. 15).

● If the System Select Switch is set to “D.S.C.”, it is not

possible to record onto the tape. Change the Switch

position to “VIDEO” (੬ pg. 18).

Recording does not start.

● The camcorder Power Switch has not been set to

“CAMERA” (“AUTO“ or “PRO.“) (੬ pg. 18).

PLAYBACK

The tape is running, but there is no

playback picture.

● The TV has not been set to its VIDEO mode or channel.

● If A/V connection is used, the TV’s VIDEO/TV Switch has

not been set to VIDEO.

Playback cannot be performed.

● If the System Select Switch is set to “D.S.C.”, it is not

possible to play back a tape. Change the Switch position to

“VIDEO” (੬ pg. 46).

Playback picture is blurred or

interrupted.

● The video heads are dirty or worn out. Consult your nearest

JVC dealer for head cleaning or replacement.

The counter indication is blurred

during Still playback.

● This is normal.

TAPE TRANSPORT

The tape stops during fast-forward or

rewind.

● The Counter Memory Function has been activated

(੬ pg. 48).

Rewinding or fast-forwarding cannot

be performed.

● The tape is already fully wound on one reel or the other.

OTHER

The picture is blurred in the Quick

Review or Retake mode.

● This is normal while recording in the EP mode. Some noise

may be present while recording in the SP mode

(੬ pg. 14).

The date and time displays

disappear.

● If you remove the power source from the camcorder while

the power is on, all settings and selections are erased. Make

sure to turn the camcorder’s power off before disconnecting

the power source.

The wrong date and time are

displayed/recorded.

● If you have not performed Date/Time Setting (੬ pg. 13),

the date and time are not displayed/recorded correctly. Be

sure that Date/Time setting is carried out.

The tape will not eject.

● The battery pack is running low.

● If the LCD monitor is not open over 60 degrees, EJECT

switch does not function.

When the System Select Switch is set to “D.S.C.”:

SYMPTOM

POSSIBLE CAUSE(S)

SHOOTING

Although the SNAPSHOT Button is

pressed, a still image is not stored in

the built-in memory.

● When the number of remaining shots available reaches “0”

(blinking), it becomes impossible to take your next shot.

Perform “DELETE” function to remove some still images

already stored in memory (੬ pg. 58).

Self-Timer Shooting is not available.

● Pressing the Recording Start/Stop Button does not start

recording in the Self-Timer Shooting procedure. Press the

SNAPSHOT Button (੬ pg. 44).

It is not possible to shoot in

sucession.

● A still image is in the process of being stored in memory for

approx. 2 seconds after the SNAPSHOT Button is pressed.

During that time, it is impossible to take another shot. When

the still image disappears and the scene you are currently

aimed at appears on the screen, take another shot (੬ pg. 22).

PLAYBACK

Although “ALL” is selected in the

DELETE Menu Screen, all still images

cannot be deleted.

● The “Protect” function is in effect for some still images. If

they are not necessary, cancel the “Protect” function, then

try deleting all still images again (੬ pg. 57).

OTHER

Date/Time Insert is not performed

● It is not possible to display the date/time on a still image.

● It is not possible to display the Instant Titles on a still image.

● It is not possible to set “REC TIME” in the Menu Screen.

while shooting a still image.

Instant Titles are not displayed while

shooting a still image.

Some settings cannot be changed in

the Menu Screen.

Since the camcorder is a microcomputer-controlled device, external noise and interference (from a TV, a

radio, etc.) might prevent it from functioning properly. For example, when a still image you shot is stored

in the camcorder's built-in memory, the above may cause the following: Although the remaining number

of shots indicator shows that shooting is possible, a still image cannot be stored in memory after shooting.

In such a case, initialize the memory by following steps 1 through 3 below. Please note that initialization

deletes all the still images (including ones for which you performed the “Protect” function) stored in the

camcorder’s memory. If you wish to keep any of the still images that are stored in memory, before

initialization first transfer them to a PC and save them. If image data is corrupt, transfer is impossible.

1. Set the System Select Switch to “D.S.C.”, then set the Power Switch to

“PLAY”.

FORMAT

CANCEL

ENTER

2. Press the SP/EP Recording Mode Button for more than 2 seconds. The

FORMAT Menu Screen appears.

3. Rotate the Select Dial to move the highlight bar to “CANCEL” or

“ENTER”, then press it.

•“CANCEL” does not initialize the memory.

•“ENTER” initializes the memory. During initialization, “ENTER” blinks.

When initialization is complete, the screen becomes blue back.

FORMAT Menu

CAUTION:

While “ENTER” is selected and it is blinking, switching off the camcorder or removing the power supply

unit (battery pack or AC Power Adapter/Charger) may cause the camcorder’s built-in memory to become

corrupt. Never remove the power supply unit at this stage.

INDEX Controls, Connectors And Indicators

EN69

u 2

e r

4 5 6

t y * ( i )

Controls

Connectors

1 Diopter Adjustment Control ................. ੬ pg. 16

w DC IN Jack .......................................... ੬ pg. 11

2 Lens Cover Open/Close Ring................ ੬ pg. 18

The connectors e to t are located beneath the

cover.

3 Video Light Switch

[LIGHT OFF/AUTO/ON]...................... ੬ pg. 30

e Video Output Connector ...................... ੬ pg. 50

4 Snapshot Button [SNAPSHOT] ....... ੬ pg. 22, 26

r Audio Output Connector ..................... ੬ pg. 50

5 •Power Zoom Lever [T/W] .................. ੬ pg. 28

t J Terminal [JLIP (Joint Level Interface Protocol)

•Speaker Volume Control [VOL.] ........ ੬ pg. 47

Connector]

•It is used to connect the camcorder to a device

such as a personal computer.

For further details consult your nearest JVC

dealer.

•JLIP-controlled editing from camcorder to VCR

is not possible if the VCR is not equipped with a

J terminal.

6 Picture Stabilizer Button

[P.STABILIZER] ..................................... ੬ pg. 29

7 Program AE Button [P.AE]..................... ੬ pg. 32

8 Fade/Wipe Button [EFFECT] ................. ੬ pg. 31

9 System Select Switch

[D.S.C./VIDEO] ................ ੬ pg. 18, 22, 46, 52

y Digital Connector ............................... ੬ pg. 53

0 •Rewind Button

[

2, REW/PAGE–] ...................... ੬ pg. 46, 52

Indicators

•Retake Rewind Button [RETAKE R] ..... ੬ pg. 29

•Quick Review Button [ R] ............. ੬ pg. 29

u Tally Lamp ........................................... ੬pg. 18

i Power Lamp ........................................ ੬pg. 18

! •Fast-Forward Button

[3, FF/PAGE+] .......................... ੬ pg. 46, 52

•Retake Forward Button [RETAKE F] .... ੬ pg. 29

@ Stop Button [5, STOP] ......................... ੬ pg. 46

# Play/Pause Button

Other Parts

o Battery Pack Mount ............................. ੬ pg. 10

p Viewfinder........................................... ੬pg. 16

Q Grip Strap ............................................ ੬pg. 16

[

4/6, PLAY/PAUSE]............................. ੬ pg. 46

$ •Select Dial [+, –, PUSH] .............. ੬ pg. 13, 36

•Bright Dial [BRIGHT] ........................ ੬ pg. 21

W •Camera sensor

Be careful not to cover this area; a sensor

necessary for shooting is built-in here.

•Remote Sensor .................................. ੬ pg. 61

% MENU/DISPLAY Button ................. ੬ pg. 19, 36

^ •Counter Reset/Memory Button

[COUNTER R/M] .............................. ੬ pg. 48

•Recording Mode Button [SP/EP] ......... ੬ pg. 14

E Video Light .......................................... ੬pg. 30

R Microphone

& EJECT Switch ....................................... ੬ pg. 15

* Recording Start/Stop Button.................. ੬ pg. 18

( Power Switch .................... ੬ pg. 18, 22, 46, 52

For use when recording.

T Eyepiece .............................................. ੬pg. 60

Y Speaker ............................................... ੬pg. 47

U LCD Monitor ....................................... ੬pg. 21

I Shoulder Strap Eyelets .......................... ੬ pg. 17

O Clock Battery Slot ................................ ੬ pg. 12

P Tripod Mounting Socket ....................... ੬ pg. 17

) Battery Release Switch

[BATTERY RELEASE] ............................ ੬ pg. 10

q PUSH Button ....................................... ੬ pg. 15

INDEX Indications

EN71

30MIN

REC SP

S T30

FINE 12

)

FADER

(

NORM

LENS COVER

PAUSE

20X

INDEX

15S

BRIGHT

TAPE END

MERRY CHRISTMAS

DEC 25. 99 AM 11 45 18

1 Cassette Warning/

% Battery Pack Remaining Power Indicator

Changes as follows according to the battery

pack’s remaining power level:

Tape Remaining Time .......................... ੬ pg. 19

When no cassette is inserted: the cassette (

warning blinks.

)

“

”. When the power is

When the Erase Protection tab is not in the position

almost gone, the indicator “ ” blinks (battery

that allows recording: the cassette (

) warning

power warning), then the unit shuts off. Replace

the battery pack with a fully charged one.

Note: The symbol containing 3 darkened squares —

— does not necessarily mean that the battery

pack is fully charged.

lights. Otherwise, the tape remaining time is

displayed and the tape remaining time warning

blinks when the tape is about to reach its end.

When the Power Switch is set to “PLAY” and a

tape is loaded: the cassette (

regardless of the Erase Protection tab’s position.

) mark is displayed

^ Focus Indicator .................................... ੬ pg. 40

& Exposure Control Level Counter ........... ੬ pg. 39

2 Recording Mode (SP/EP) Indicator ........ ੬ pg. 14

* White Balance Mode Indicator ............ ੬ pg. 42

( •Record–Standby Mode Indicator ....... ੬ pg. 18

•Lens Cover Warning:

3, 8 Program AE Indicator ...................... ੬ pg. 32

Displayed at 3 for approx. 2 seconds when

Program AE with special effects is switched from

one mode to another by pressing P.AE., then only

the indicator remains at 8.

LENS COVER .................................... ੬ pg. 19

) Clock Battery Warning

Blinks for approx. 10 seconds when the power is

turned on. This display also blinks when the clock

(lithium) battery is either not installed or has

discharged. Install or replace the old battery with

a new one (੬ pg. 12).

3, 9 Fade/Wipe-Standby Indicator .......... ੬ pg. 31

Displayed at 3 for approx. 2 seconds when the

Fade/Wipe is switched from one effect to another

by pressing EFFECT, then only the indicator

remains at 9.

q •Tape End Display: TAPE END ............ ੬ pg. 19

Appears when the end of the tape is reached

during playback, recording or fast-forward.

•Condensation Warning:

4 •Picture Mode Display ................. ੬ pg. 23, 24

•Remaining Number Of Shots

Indicator ..................................... ੬pg. 23, 24

5 Tape Length Indicator .......................... ੬ pg. 14

6 Zoom Indicator Bar ............................. ੬ pg. 28

When this indication appears, all functions

except tape eject and power on/off are disabled.

Turn the unit off (without removing the power

source) for a few hours, and when you turn it on

again the indication should disappear.

Zoom Level Indicator

Approximate Zoom Ratio

7 Recording Indicator ............................. ੬ pg. 18

•Head Clog Warning:

0 Picture Stabilizer Indicator ................... ੬ pg. 29

Appears if dirty heads are detected during

recording. In such a case, use the optional

Cleaning Cassette. If, after using it, the problems

still exist, consult your nearest JVC dealer.

! Interval Timer/Recording Time

Indicator ............................................. ੬pg. 44

@ •Bright Level Indicator ........................ ੬ pg. 47

•Speaker Volume Indicator ................. ੬ pg. 47

# Instant Title Display ............................. ੬ pg. 35

$ Date/Time Display ............................... ੬ pg. 34

INDEX Terms

AC Power Adapter/Charger ............................ pg. 10

Animation Recording ..................................... pg. 45

Auto Date Record .......................................... pg. 34

Auto Focus .................................................... pg. 40

Auto Shut Off ...........................................pg. 19, 46

Fade-In/Out ................................................... pg. 31

Fast-Forward Tape ......................................... pg. 46

FINE Mode .................................................... pg. 24

Full Image ................................................ pg. 23, 27

Grip Adjustment ............................................ pg. 16

Battery Pack .............................................pg. 10, 74

Brighten The Image ....................................... pg. 39

Brighten The LCD Monitor ............................. pg. 21

High Speed Shutter Mode .............................. pg. 33

INDEX Menu ................................................. pg. 56

Index Mode ................................................... pg. 56

Index Number ............................................... pg. 56

Instant Titles .................................................. pg. 35

Interface Shooting.......................................... pg. 21

Car Battery ..................................................... pg. 11

Cassette Adapter ............................................ pg. 49

Charge Marker................................................ pg. 11

Charging The Battery Pack ............................. pg. 10

Clean The Camcorder .................................... pg. 65

Clock (Lithium) Battery .................................. pg. 12

COM Port (RS-232C) ..................................... pg. 53

Connection To A VCR/TV .............................. pg. 50

Connection To A Windows PC/Macintosh ...... pg. 53

Contents .......................................................pg. 8, 9

Counter Memory ........................................... pg. 48

JLIP ID NO. ................................................... pg. 38

Journalistic Shooting ...................................... pg. 21

JPEG.............................................................. pg. 24

LCD monitor/Viewfinder, Indications.............. pg. 71

Load A Tape .................................................. pg. 15

Darken The Image ......................................... pg. 39

Darken The LCD Monitor .............................. pg. 21

Date/Time Display ......................................... pg. 34

Date/Time Settings ......................................... pg. 13

DELETE Menu ............................................... pg. 58

Delete Mode ................................................. pg. 58

Delete Select Menu ....................................... pg. 58

Demonstration Mode ..................................... pg. 38

Digital Zoom ................................................. pg. 37

Digital Still Camera ................................. pg. 22 – 25

Diopter Adjustment ....................................... pg. 16

Discharge The Battery Pack ........................... pg. 10

Manual Focus................................................ pg. 41

Menu Screen ...................................... pg. 37, 38, 55

Modem Port .................................................. pg. 53

Move The Page Back ..................................... pg. 52

Move The Page Next ..................................... pg. 52

ND Effect Mode............................................. pg. 33

Nega/Posi Mode ............................................ pg. 33

Electronic Fog Filter Mode ............................. pg. 33

Erase Protection ............................................. pg. 15

Exposure Control ........................................... pg. 39

EN73

Padlock Mark ................................................ pg. 57

Picture Mode Setting ...................................... pg. 24

Picture Stabilizer ........................................... pg. 29

Pin-Up Image ........................................... pg. 23, 27

Playback (D.S.C.)........................................... pg. 52

Playback (VIDEO) .......................................... pg. 46

Power Switch Position ................................... pg. 18

Printer Port .................................................... pg. 53

Program AE With Special Effects ...............pg. 32, 33

PROTECT Menu ............................................ pg. 57

Protect Mode ................................................. pg. 57

Provided Accessories ....................................... pg. 9

Tally .............................................................. pg. 38

Tape Counter ................................................. pg. 46

Tape Dubbing ...........................................pg. 50, 51

Tape Length Setting........................................ pg. 14

Tele Macro .................................................... pg. 38

Time-Lapse Shooting ..................................... pg. 45

Tracking ........................................................ pg. 47

Tripod Mounting............................................ pg. 17

Twilight Mode ............................................... pg. 33

Unload A Tape .............................................. pg. 15

Video Light .................................................... pg. 30

Viewfinder Adjustment .................................. pg. 16

Quick Review ............................................... pg. 29

Recording, Advanced Features (VIDEO) ... pg. 31 – 45

Recording, Start/Stop (VIDEO) ................... pg. 18, 19

Recording Mode ............................................ pg. 14

Record-Standby ............................................. pg. 18

Retake ........................................................... pg. 29

Rewind The Tape........................................... pg. 46

White Balance Adjustment............................. pg. 42

Wide Mode ................................................... pg. 37

Wipe-In/Out .................................................. pg. 31

Zooming ....................................................... pg. 28

Self-Recording ............................................... pg. 21

Self-Timer .................................................pg. 44, 61

Sepia Mode ................................................... pg. 33

Shooting,

Advanced Features (D.S.C.) ............ pg. 32, 36 – 44

Shooting (D.S.C.) .................................... pg. 22 – 25

Shoulder Strap Attachment............................. pg. 17

Shuttle Search................................................ pg. 48

Slide Show Mode .......................................... pg. 55

Snapshot Mode ........................................pg. 22, 26

Snapshot (VIDEO) ..................................... pg. 26, 27

Specifications ................................................ pg. 77

Sports Mode .................................................. pg. 33

STANDARD Mode......................................... pg. 24

Star Mark On The Setting Menus ......... pg. 56, 57, 59

Still Image Data Transfer ................................ pg. 53

Still Playback ................................................. pg. 48

Store A Still Image In The Built-In Memory ..... pg. 22

Super LoLux (S.LX) ......................................... pg. 37

CAUTIONS

DANGER:

Battery Packs

The battery packs are nickel-cadmium

or nickel metal-hydride batteries.

Before using the supplied battery pack

or an optional battery pack, be sure to

read the following cautions:

Video Light

•The video light becomes extremely hot. Do not

touch it either while in operation or soon after

turning it off, otherwise serious injury may result.

•Do not place the camcorder into the carrying case

immediately after using the video light, since it

remains extremely hot for some time.

1.To avoid hazard . . .

... do not burn.

Terminals

... do not short-circuit the terminals.

... do not modify or disassemble.

... use only specified chargers.

•When operating, keep a distance of about 30 cm

(1 ft.) between the video light and people or object.

•Do not use near flammable or explosive materials.

•It is recommended that you consult your nearest

JVC dealer for replacing the video light.

2. To prevent damage and prolong service life . . .

... do not subject to unnecessary shock.

... avoid repeated charging without fully discharg-

ing.

When using the AC Power Adapter/Charger in areas

other than the USA

Ⅲ The provided AC Power Adapter/Charger features

automatic voltage selection in the AC range from

110 V to 240 V.

USING HOUSEHOLD AC PLUG ADAPTER

In case of connecting the unit’s power cord to an AC

wall outlet other than American National Standard

C73 series type use an AC plug adapter, called a

“Siemens Plug”, as shown.

For this AC plug adapter, consult your nearest JVC

dealer.

... charge in an environment where temperatures

are within the tolerances shown in the chart

below. This is a chemical reaction type

battery—cooler temperatures impede chemical

reaction, while warmer temperatures can

prevent complete charging.

... store in a cool, dry place. Extended exposure to

high temperatures will increase natural

discharge and shorten service life.

... avoid prolonged uncharged storage.

... remove from charger or powered unit when

not in use, as some machines use current even

when switched off.

Plug adapter

NOTES:

●It is normal for the battery pack to be warm after

charging, or after use.

Temperature Range Specifications

Charging .............. 10°C to 35°C (50°F to 95°F)

Operation ............ 0°C to 40°C (32°F to 104°F)

Storage ................ –10°C to 30°C (14°F to 86°F)

●Recharging time is based on room temperature of

20°C.

General Battery Precautions

•When the C-P6U or C-P7U (cassette adapter) is not

functioning even when correctly operated, the

battery is exhausted. Replace it with a fresh one.

•Use only the following battery:

●The lower the temperature, the longer recharging

takes.

C-P6U or C-P7U..................... AA (R6) size

Please make note of the following rules for battery

use. When misused, battery can leak or explode.

1. Refer to the C-P6U/C-P7U instructions when

replacing the battery.

2. Do not expose the battery to excessive heat as it

can leak or explode.

3. Do not dispose of battery in a fire.

4. Remove battery from the unit if it is to be stored for

an extended period to avoid battery leakage which

can cause malfunctions.

CAUTIONS (cont.)

EN75

Cassettes

To properly use and store your cassettes, be sure to

read the following cautions:

Main Unit

1.For safety, DO NOT . . .

... open the camcorder’s chassis.

... disassemble or modify the unit.

1.During use . . .

... short-circuit the terminals of the battery pack.

Keep it away from metallic objects when not in

use.

... allow inflammables, water or metallic objects

to enter the unit.

... remove the battery pack or disconnect the

power supply while the power is on.

... leave the battery pack attached when the

camcorder is not in use.

... make sure the cassette bears the VHS-C mark.

... be aware that recording onto prerecorded tapes

automatically erases the previously recorded

video and audio signals.

... make sure the cassette is positioned properly

when inserting.

... do not load and unload the cassette

repeatedly without allowing the tape to run at

all. This slackens the tape and can result in

damage.

2.Avoid using the unit . . .

... in places subject to excessive humidity or dust.

... in places subject to soot or steam such as near

a cooking stove.

... do not open the front tape cover. This exposes

the tape to fingerprints and dust.

2.Store cassettes . . .

... in places subject to excessive shock or

vibration.

... away from heaters or other heat sources.

... out of direct sunlight.

... near a television set.

... where they won’t be subject to unnecessary

shock or vibration.

... where they won’t be exposed to strong

magnetic fields (such as those generated by

motors, transformers or magnets).

... vertically, in their original cases.

... near appliances generating strong magnetic or

electric fields (speakers, broadcasting antennas,

etc.).

... in places subject to extremely high (over 40°C

or 104°F) or extremely low (under 0°C or 32°F)

temperatures.

3.DO NOT leave the unit . . .

... in places of over 50°C (122°F).

... in places where humidity is extremely low.

(below 35%) or extremely high (above 80%).

... in direct sunlight.

... in a closed car in summer.

... near a heater.

4.To protect the unit, DO NOT . . .

... allow it to become wet.

... drop the unit or strike it against hard objects.

... subject it to shock or excessive vibration during

transportation.

... keep the lens directed at extremely bright

objects for long periods.

... direct the eyepiece of the viewfinder at the sun.

... carry it by holding the viewfinder or the LCD

monitor. Be sure to hold the main unit with

both hands or use the grip.

... swing it excessively when using the shoulder

strap.

LCD Monitor

How to handle a CD-ROM

•Take care not to soil or scratch the mirror surface

(opposite to the printed surface). Do not write

anything or put a sticker on either the front or back

surface. If the CD-ROM gets dirty, gently wipe it

with a soft cloth outward from the center hole using

a circular motion.

1.To prevent damage to the LCD monitor, DO

NOT . . .

... push it strongly or apply any shocks.

... place the camcorder with the LCD monitor on

the bottom.

2.To prolong service life . . .

•Do not use conventional disc cleaners or cleaning

spray.

... avoid rubbing it with coarse cloth.

3.Be aware of the following phenomena for

LCD monitor use. These are not malfunc-

tions . . .

•While using the camcorder, the surface around the

LCD monitor and/or the back of the LCD monitor

may heat up.

•Do not bend the CD-ROM or touch its mirror

surface.

•Do not store your CD-ROM in a dusty, hot or

humid environment. Keep it away from direct

sunlight.

•If you leave power on for a long time, the surface

around the LCD monitor becomes hot.

About moisture condensation . . .

● You may have observed that pouring a cold

liquid into a glass will cause drops of water to

form on the glass’ outer surface. This same

phenomenon occurs on the head drum of a

camcorder when it is moved from a cool place

to a warm place, after heating a cold room,

under extremely humid conditions or in a

place directly subjected to the cool air from an

air conditioner.

● Moisture on the head drum can cause severe

damage to the video tape, and can lead to

internal damage to the camcorder itself.

Serious malfunctioning

If malfunctioning occurs, stop using the unit

immediately and consult your local JVC dealer.

SPECIFICATIONS

EN77

Camcorder

General

Format

: VHS NTSC standard

: DC 6.0 V

Operating temperature: 0°C to 40°C (32°F to 104°F)

Operating humidity : 35% to 80%

Storage temperature : –20°C to 50°C (–4°F to 122°F)

Power source

Power consumption

LCD monitor off,

viewfinder on

LCD monitor on,

viewfinder off

LCD monitor on,

viewfinder on

Video light

Weight

Dimensions

: Approx. 870 g (2.0 lbs)

: 99 (W) x 119 (H) x 198 (D) mm

(3-15/16" x 4-11/16" x 7-13/16")

(with the LCD monitor closed

and with the viewfinder fully

tilted downward)

: 6.9 W

: 7.4 W

: 8.0 W

: 2.9 W

: NTSC-type

Pickup

Lens

: 1/4” format CCD

Signal system

Video recording system

Luminance

: F1.6, f = 3.9 to 62.4 mm, 16:1

power zoom lens with auto iris

and macro control, filter

diameter 40.5 mm

: FM recording

Color

: Converted sub-carrier

direct recording

Viewfinder

: Electronic viewfinder

with 0.55” color LCD

Conforms to VHS standard

Cassette

Tape speed

cassette

White balance

adjustment

LCD monitor

: Auto/Manual adjustment

: 3” diagonally measured, LCD

panel/TFT active matrix system

: Monaural

: 33.35 mm/sec. (1-5/16 ips)

: 11.12 mm/sec. (7/16 ips)

Recording time (max.)

Speaker

: 40 minutes

: 120 minutes (with TC-40)

Connectors

JLIP

D.S.C. format

Recording format

: ø3.5 mm, 4-pole, mini-head

jack

: Digital data storage (based on

JPEG)

(compatible with RC-5325 plug)

: 1 Vp-p, 75 Ω unbalanced,

analog output

Recording medium : Built-in flash memory,

Video

2 Mbyte

Number of storable

shots

(via Video output connector)

: FINE mode:

Audio

: –8 dBs, 1 kΩ analog output

(via Audio output connector)

: ø2.5 mm, 4-pole, mini-head

jack

approx. 30 shots

STANDARD mode:

approx. 60 shots

: 640 x 480 pixels

Digital

Image size

(when captured

on a PC)

Provided Accessories ..................

pg. 9

AC Power Adapter/Charger AA-V15U

੬

Power requirement

U.S.A. and Canada : AC 120 V`, 60 Hz

Other countries : AC 110 V to 240 V`, 50/60

Optional Accessories

•Battery Packs BN-V12U, BN-V20U, BN-V856U

•Car Battery Charger BH-V3U

•Battery Charger BH-VC10U

Power consumption : 23 W

Output

Charge

VTR

•Car Battery Cord AP-V7U

: DC 8.5 V

: DC 6.3 V

, 1.3 A

, 1.8 A

•Compact VHS-C Cassettes TC-40/30/20

•Active Carrying Bag CB-V7U

•Audio/Video Cable

Charging system

: Constant current, peak

detection, timer controlled

: 140 (W) x 42 (H) x 68 (D) mm

(5-9/16” x 1-11/16” x 2-11/16”)

: Approx. 300 g (0.71 lbs)

Dimensions

Weight

Some accessories are not available in some areas. Please

consult your nearest JVC dealer for details on accessories

and their availability.

Specifications shown are for SP mode unless otherwise

indicated. E & O.E. Design and specifications subject to

change without notice.

Cassette Adapter C-P7U

Dimensions

: 188 (W) x 25 (H) x 104 (D) mm

(7-7/16” x 1” x 4-1/8”)

Weight

Accessory

: Approx. 240 g (0.53 lbs)

: “AA (R6)”-size battery x 1

MEMO

VICTOR COMPANY OF JAPAN, LIMITED

⁰^P²^ri⁹ⁿ⁹^te^M^d^Kⁱⁿ^V*^Ja^U^p^N^an*^YP

ATN Fusion Image Intensification Thermal System FIITS14 User Manual
Attwood 4801 User Manual
Audiovox UB104W User Manual
Bushnell Binoculars 260228 User Manual
Canon HF R206 User Manual
Casio SE S300 User Manual
Directed Electronics 250 User Manual
Harman Kardon DPR 2005 User Manual
Honeywell AQUASTATIC L7224 User Manual
JVC AA V33U User Manual