JVC GET0471 001A User Manual

VCD/CD RECEIVER

KD-SV3305

For canceling the display demonstration, see page 7.

For installation and connections, refer to the separate manual.

INSTRUCTIONS

GET0471-001A

[U/UH]

The following marks are used to indicate...

: Built-in VCD/CD player operations.

: External CD changer operations.

CONTENTS

Control panel ..................................

Remote controller—^RM-RK120.............

: Indicator displayed for the

corresponding operation.

Getting started................................

Basic operations...................................................

How to use the MODE button

If you press MODE, the unit goes into functions mode,

then the number buttons (except “1” and “4”) and

Radio operations .............................

Disc operations................................

Playing a disc in the unit .....................................

/¢ buttons work as different function

buttons.

Playing discs in the CD changer ........................... 10

Sound adjustments.......................... 14

General settings—PSM ................... 15

iPod/D. player operations................. 17

Ex.: When number button 2 works as

MO (monaural) button.

Other external component

operations ................................... 19

To use these buttons for their original functions

again after pressing MODE, wait for 5 seconds

without pressing any of these buttons until the

functions mode is cleared or press MODE again.

Maintenance ................................... 19

More about this unit ........................ 20

Troubleshooting.............................. 23

Specifications.................................. 25

Detaching the control panel

For safety...

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car...

Attaching the control panel

If you have parked the car for a long time in hot or cold

weather, wait until the temperature in the car becomes

normal before operating the unit.

Control panel

Parts identification

Display window

1 4 /¢ buttons

;

DISP (display) button

(standby/on attenuator) button

(control panel release) button

Disc information indicators—TAG (ID3 Tag),

(folder), (track/file)

Disc type indicators—WMA, MP3

Playback source indicators—

Remote sensor

DO NOT expose the remote sensor to strong light

(direct sunlight or artificial lighting).

Loading slot

Display window

CH: Lights up only when CD-CH is selected as the

playback source.

6 0 (eject) button

EQ (equalizer) button

SRC (source) button

BAND button

6 (play/pause) button

Control dial

DISC: Lights up for the built-in CD player.

Playback mode / item indicators— RND (random),

(disc), (folder), RPT (repeat)

LOUD (loudness) indicator

EQ (equalizer) indicator

SEL (select) button

Sound mode (C-EQ: custom equalizer) indicators—

JAZZ, CLASSIC, HIP HOP, POPS, ROCK, USER

Tr (track) indicator

Source display / Volume level indicator

Main display

MO (monaural) button

SSM (Strong-station Sequential Memory) button

Number buttons

RPT (repeat) button

RND (random) button

MODE button

Tuner reception indicators—ST (stereo),

MO (monaural)

Main elements and features

Remote controller—

RM-RK120

Installing the lithium coin battery

(CR2025)

Aim the remote controller directly at the remote

sensor on the unit. Make sure there is no obstacle

in between.

Warning:

• Do not install any battery other than CR2025 or

its equivalent; otherwise, it may explode.

• Do not leave the remote controller in a place

(such as dashboards) exposed to direct sunlight

for a long time; otherwise, it may explode.

• Store the battery in a place where children

cannot reach to avoid risk of accident.

• To prevent the battery from over-heating,

cracking, or starting a fire:

– Do not recharge, short, disassemble, heat the

battery, or dispose of it in a fire.

– Do not leave the battery with other metallic

materials.

SOURCE button

• Selects the playback source.

(standby/on attenuator) button

• Turns the power on if pressed briefly or

attenuates the sound when the power is on.

• Turns the power off if pressed and held.

3 2 REV (reverse) / FWD (forward) 3 buttons

• Searches for stations if pressed briefly.

• Fast-forwards or reverses the track if pressed and

held.

– Do not poke the battery with tweezers or similar

tools.

– Wrap the battery with tape and insulate when

throwing away or saving it.

• Changes the tracks if pressed briefly.

• While listening to an Apple iPod or a JVC

D. player (in menu selecting mode):

– Selects an item if pressed briefly. (Then, press

DOWN ∞ to confirm the selection.)

– Skips 10 items at a time if pressed and held.

Continued on the next page

VOL. + / – buttons

• Adjusts the volume level.

ENTER and number buttons

PBC (Playback Control) button

• Activates or deactivates the PBC function.

RETURN button

• Selects a track/file directly.

• Returns to the previous menu while playing a

VCD in PBC function.

OSD (On-Screen Display) button

• Turn on and off the OSD on the monitor.

AUDIO button

– Press the number button(s), then press ENTER.

– Not used for iPod/D. player operations.

• Selects an item from the menu while playing

back a Video CD (VCD) in Playback Control (PBC)

function.

• Selects the audio channel for VCD playback.

– Press the number button(s), then press ENTER.

• Selects the discs while operating the CD changer.

– To select disc number 1 – 6, press number

button 1 – 6 briefly.

* 5 UP

: Returns to the previous menu.

DOWN ∞ : Confirms the selection.

– To select disc number 7 – 12, press and hold

number button 1 (7) – 6 (12).

EQ (equalizer) button

• Selects the sound mode (C-EQ: custom

equalizer).

BAND 6 button

• Changes the FM/AM bands.

• Stops disc playback temporarily. To resume

playback, press the button again.

– While playing a VCD, the playback scene at the

moment stops and remain still.

– Not used for CD changer, iPod, or D. player

operations.

8 5 UP / DOWN ∞ buttons

• Changes the preset stations.

• Changes the folder of the MP3/WMA discs if

pressed briefly.

• Changes the disc while operating the CD changer

if pressed and held.

• While listening to an iPod or a D. player:

– Pauses/stops or resumes playback with

DOWN ∞.

– Enters the main menu with 5 UP.

(Now 5 UP / DOWN ∞/2 REV / FWD 3 work

as the menu selecting buttons.)*

To drop the volume in a

moment (ATT)

To restore the sound, press the

button again.

Getting started

Basic operations

To turn off the power

~ Turn on the power.

Basic settings

• See also “General settings — PSM” on pages 15 and

16.

* You cannot select these sources if they are not

ready or not connected.

! For FM/AM tuner

1 Canceling the display demonstrations

Select “DEMO,” then “DEMO OFF.”

2 Setting the clock

Select “CLOCK H” (hour), then adjust the hour.

Select “CLOCK M” (minute), then adjust the

minute.

⁄ Adjust the volume.

Finish the procedure.

Volume level appears.

To check the current clock time while the

power is turned off

@ Adjust the sound as you want. (See

page 14.)

Caution on volume setting:

Discs produce very little noise compared with other

sources. Lower the volume before playing a disc

to avoid damaging the speakers by the sudden

increase of the output level.

When an FM stereo broadcast is hard to

receive

Radio operations

Lights up when monaural mode is activated.

Reception improves, but stereo effect will be lost.

To restore the stereo effect, repeat the same

procedure. “MONO OFF” appears and the MO indicator

goes off.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

! Start searching for a station.

Storing stations in memory

You can preset six stations for each band.

When a station is received, searching stops.

To stop searching, press the same button

again.

FM station automatic presetting—

SSM (Strong-station Sequential

Memory)

Select the FM band (FM1 – FM3) you want to

store into.

To tune in to a station manually

In step ! above...

Select a desired station frequency.

“SSM” flashes, then disappears when automatic

presetting is over.

Local FM stations with the strongest signals are

searched and stored automatically in the FM band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset number

4 of the FM1 band.

Disc operations

Playing a disc in the unit

All tracks will be played repeatedly until you change the

source or eject the disc.

• If a disc menu appears on the monitor while playing a

VCD with PBC, see page 11.

Preset number flashes for a while.

Before performing any operations, make sure the

following....

• Turn on the monitor and select the appropriate

monitor input before playing a VCD.

• If you turn on the monitor, you can also control the

MP3/WMA playback by referring to the monitor

screen (see page 12).

Listening to a preset station

Select the preset station (1 – 6) you want.

• Select the video system suitable for your monitor (see

page 16).

To stop play temporarily

To resume playback, press the

button again.

To check the other information while

listening to the radio

To stop play and eject the

disc

Clock Ô Frequency

Continued on the next page

To fast-forward or reverse the track

To go to the next or previous tracks

Playing discs in the CD changer

All discs in the magazine will be played repeatedly until

you change the source.

• Ejecting the magazine will also stop playing.

* If you have changed the external input setting

to “EXT IN” (see page 16), you cannot select the

CD changer.

To go to the next or previous folders (only for

MP3 or WMA discs)

Ÿ Select a disc.

For disc number from 01 – 06:

For MP3 discs:

For WMA discs:

For disc number from 07 – 12:

About MP3 and WMA discs

MP3 and WMA “tracks” (words “file” and “track” are

used interchangeably) are recorded in “folders.”

To locate a particular track (for CD or VCD

with PBC set to “PBC OFF”) or folder (for MP3

or WMA discs) directly

To select a number from 01 – 06:

About the CD changer

It is recommended to use a JVC MP3-compatible CD

changer with your unit.

• You can also connect MP3-incompatible CD changers.

However, these units are not compatible with MP3

discs.

To select a number from 07 – 12:

• You cannot use the CH-X99, CH-X100, and KD-MK

series CD changers with this unit.

• You cannot control and play any WMA or VCD disc in

the CD changer.

• Disc text information recorded in the CD Text can be

displayed when a JVC CD Text compatible CD changer

is connected.

• For connection, see Installation/Connection Manual

(separate volume).

• To use direct folder access on MP3/WMA discs, it

is required that folders are assigned with 2-digit

numbers at the beginning of their folder names—

01, 02, 03, and so on.

To select a particular track in a folder

(for MP3 or WMA discs):

Playback Control (PBC) operations

On-Screen (OSD) information

This operation is only possible when using the

remote controller.

This operation is only possible when using the

remote controller.

While playing a VCD....

PBC ON Ô PBC OFF

You can check the track number and elapsed playing

time if the monitor is turned on.

While playing a disc....

• To turn off the On-Screen Display,

press the button again.

PBC ON : A menu appears on the monitor.

PBC OFF: Cancels.

Current/total track number

Elapsed playing time

• A menu may be a list of items, submenus, or

some moving pictures.

Select the item you want.

Selecting the audio channel

This operation is only possible when using the

remote controller.

• To select an item from the submenus, repeat this

step.

You can select the audio channel to play. (This is

convenient when playing a Karaoke VCD.)

The selected item starts playback automatically.

To correct a mis-entry and to return to the

previous menu

STEREO : To listen to normal stereo (left/right)

playback.

MONO L : To listen to the L (left) audio channel.

MONO R : To listen to the R (right) audio channel.

• The audio channel is automatically set to “STEREO”

when you change the disc or source.

To select a folder

To select a track

MP3/WMA control screen operations

You can also control the playback of an MP3/WMA disc

by referring to the monitor.

• The control screen automatically appears on the

monitor when you insert an MP3/WMA disc.

• Pressing these buttons repeatedly can also select

tracks from the previous/next folders.

• See also page 10 for using the buttons on the control

panel to select a folder or track.

Selecting the playback modes

You can use only one of the following playback modes

at a time.

• For VCD: While PBC (see page 11) is not in use.

Artiste name* (only for MP3 discs)

• The artiste name will scroll on the monitor if it

cannot be shown at a time.

Operation mode—PLAY, PAUSE, FF (fast-forward),

FR (fast-reverse), SELECT (selected track number),

REPEAT TRACK, REPEAT FOLDER, REPEAT OFF,

RANDOM FOLDER, RANDOM DISC, RANDOM OFF

• Operation mode appears for a while on the

monitor.

Select your desired playback mode.

Repeat play

Folder name*

Track title* (only for MP3 discs)

• The track title will scroll on the monitor if it

cannot be shown at a time.

Mode

Plays repeatedly

TRK RPT : The current track.

Highlighted bar for the current file name*

OSD indication—Current/total track number,

Elapsed playing time

• Appears only if you turn on the OSD (see page

11).

FLDR RPT*¹: All tracks of the current folder.

DISC RPT*²: All tracks of the current disc.

RPT OFF : Cancels.

Current list/total list number

Track list

• The monitor can show 12 tracks at a time and a

maximum of 239 tracks for a disc.

* Some symbols will not be shown (and will be

substituted or blanked) on the control screen.

• For MP3 disc : When “TAG DISP” is set to “TAG OFF”

• For WMA disc :

Random play

Mode

Plays at random

FLDR RND*¹: All tracks of the current folder,

then tracks of the next folder and

so on.

: Clock with the current track number

: Elapsed playing time with the current track

number

DISC RND : All tracks of the current disc.

MAG RND*²: All tracks of the inserted discs.

If the current disc is an audio CD or a VCD, “NO NAME”

appears.

Only for the built-in CD player.

If an MP3 file does not have Tag information, folder

name and file name appear. In this case, the TAG

indicator will not light up.

RND OFF

: Cancels.

Only while playing an MP3 or a WMA disc.

Only while playing discs in the CD changer.

Other main functions

Prohibiting disc ejection

You can lock a disc in the loading slot.

Changing the display information

While playing an audio CD, a CD Text, or a VCD

with PBC set to “PBC OFF” (see page 11)

To cancel the prohibition, repeat the same

procedure.

While playing an MP3 or a WMA*²disc

• Only for MP3 disc : When “TAG DISP” is set to

“TAG ON” (see page 16)

Adjusting the sound

Sound adjustments

You can select a preset sound mode suitable to the

music genre (C-EQ: custom equalizer).

You can adjust the sound characteristics to your

preference.

Preset values

BAS

TRE

LOUD

(bass) (treble) (loudness)

Indication (For)

USER

(Flat sound)

+03 +01

+01 –02

+04 +01

+02 00

+02 +03

OFF

Indication [Range]

ROCK

(Rock or disco music)

BAS*¹(bass)

Adjust the bass. [–06 to +06]

CLASSIC

(Classical music)

OFF

TRE*¹(treble)

Adjust the treble. [–06 to +06]

POPS

(Light music)

FAD*²(fader)

Adjust the front and rear speaker balance. [R06 to F06]

HIP HOP

(Funk or rap music)

BAL (balance)

Adjust the left and right speaker balance.

[L06 to R06]

JAZZ

(Jazz music)

OFF

LOUD*¹(loudness)

Boost low and high frequencies to produce a well-

balanced sound at low volume level.

[LOUD ON or LOUD OFF]

VOL (volume)

Adjust the volume. [00 to 30 or 50*³]

When you adjust the bass, treble, or loudness, the

adjustment you have made is stored for the currently

selected sound mode (C-EQ) including “USER.”

If you are using a two-speaker system, set the fader

level to “00.”

Depending on the amplifier gain control setting. (See

page 16 for details.)

General settings — PSM

You can change PSM (Preferred Setting Mode) items listed in the table that follows.

Repeat steps 2 and 3 to adjust other PSM

items if necessary.

Select a PSM item.

Finish the procedure.

Adjust the PSM item selected.

Indications

DEMO

Item

Setting, [reference page]

(

: Initial)

• DEMO ON

Display demonstration will be activated automatically if no

operation is done for about 20 seconds, [7].

Cancels.

Display demonstration

• DEMO OFF

CLOCK H

1 – 12

[Initial: 1 (1:00)], [7]

Hour adjustment

CLOCK M

00 – 59

[Initial: 00 (1:00)], [7]

Minute adjustment

DIMMER

Dimmer

• ON

• OFF

Dims the display illumination of this unit.

Cancels.

TEL

• MUTING 1/

MUTING 2:

• OFF

Select either one which mutes the sounds while using a cellular

phone.

Cancels.

Telephone muting

Continued on the next page

Indications

Item

Setting, [reference page]

(

: Initial)

SCROLL *¹

Scroll

• ONCE

• AUTO

• OFF

Scrolls the track information once.

Repeats scrolling (at 5-second intervals).

Cancels.

• Pressing DISP for more than one second can scroll the display

regardless of the setting.

TAG DISP

Tag display

• TAG ON

• TAG OFF

Shows the Tag information while playing MP3 tracks, [13].

Cancels.

AMP GAIN

Amplifier gain control

• LOW PWR

VOL 00 – VOL 30 (Select this if the maximum power of the speaker

is less than 50 W to prevent damaging the speaker.)

VOL 00 – VOL 50

• HIGH PWR

VIDEO

Video system

• PAL

• NTSC

Select this if your monitor is of the PAL color system.

Select this if your monitor is of the NTSC color system.

• Press SEL to activate the selection before you select the other PSM

items to adjust.

EXT IN *²

External input

• CHANGER

To use a JVC CD changer, [10], an Apple iPod or a JVC D. player,

[17].

To use any other external component than the above, [19].

• EXT IN

Some characters or symbols will not be shown correctly (or will be blanked) on the display.

Displayed only when one of the following sources is selected—FM, AM, DISC, or LINE IN.

To pause*¹or stop*²playback

iPod/D. player operations

This unit is ready for operating an Apple iPod or a JVC

D. player from the control panel.

To resume playback, press 4 after pressing

MODE.

Before operating your iPod or D. player:

Connect either one of the following (separately

purchased) to the CD changer jack on the rear of this

unit.

• Interface adapter for iPod—KS-PD100 for

controlling an iPod.

To fast-forward or reverse the track

To go to the next or previous tracks

• D. player interface adapter—KS-PD500 for

controlling a D. player.

• For connection, see Installation/Connection Manual

(separate volume).

• For details, refer also to the manual supplied with the

interface adapter.

For iPod

For D. player

Preparations:

Make sure “CHANGER” is selected for the external input

setting, see page 16.

Playback starts automatically from where it has

been paused*¹or stopped*²previously.

! Adjust the volume.

⁄ Adjust the sound as you want. (See

page 14.)

Continued on the next page

Selecting a track from the menu

Selecting the playback modes

Enter the main menu.

Select your desired playback mode.

Now the 4 /¢ buttons

work as the menu selecting buttons*.

Repeat play

Select the desired menu.

ONE RPT

Functions the same as “Repeat One” of the iPod or

“Repeat Mode = One” for the D. player.

ALL RPT

For iPod:

Functions the same as “Repeat All” of the iPod or

“Repeat Mode = All” for the D. player.

PLAYLIST Ô ARTISTS Ô ALBUMS Ô

SONGS Ô GENRES Ô COMPOSER Ô

(back to the beginning)

RPT OFF

Cancels.

For D. player:

Random play

PLAYLIST Ô ARTIST Ô ALBUM Ô

GENRE Ô TRACK Ô (back to the

beginning)

ALBM RND*

Functions the same as “Shuffle Albums” of the

iPod.

Confirm the selection.

SONG RND/RND ON

Functions the same as “Shuffle Songs” of the iPod

or “Random Play = On” of the D. player.

To move back to the previous menu, press ¢

after pressing MODE.

RND OFF

• If a track is selected, playback starts

automatically.

• If the selected item has another layer, you will

enter the layer. Repeat steps 3 and 4 until the

desired track is played.

Cancels.

* For iPod: Functions only if you select “ALL” in

“ALBUMS” of the main “MENU.”

• Holding 4 /¢ can skip 10 items at

a time.

To check the other information while

listening to an iPod or a D. player

* The menu selecting mode will be canceled:

– If no operations are done for about 5 seconds.

– When you confirm the selection of a track.

Other external component Maintenance

operations

How to clean the connectors

Frequent detachment will deteriorate the connectors.

To minimize this possibility, periodically wipe the

connectors with a cotton swab or cloth moistened with

alcohol, being careful not to damage the connectors.

You can connect an external component to the LINE IN

plugs on the rear, and another to the CD changer jack

on the rear using the Line Input Adapter—KS-U57

(not supplied) or AUX Input Adapter—KS-U58 (not

supplied).

• For connection, see Installation/Connection Manual

(separate volume).

• For listening to the iPod or D. player, refer to pages

17 and 18.

Connector

Moisture condensation

Moisture may condense on the lens inside the unit in

the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.

Should this occur, the unit may malfunction. In this

case, eject the disc and leave the unit turned on for a

few hours until the moisture evaporates.

If “EXT IN” does not appear, see page 16 and

select the external input (“EXT IN”).

Ÿ Turn on the connected component and

start playing the source.

How to handle discs

When removing a disc from its

case, press down the center holder of

the case and lift the disc out, holding

it by the edges.

Center holder

! Adjust the volume.

• Always hold the disc by the edges. Do not touch its

recording surface.

When storing a disc into its case, gently insert the

disc around the center holder (with the printed surface

facing up).

⁄ Adjust the sound as you want. (See

page 14.)

• Make sure to store discs into the cases after use.

To check the other information while

listening to an external component

Clock Ô EXT IN or LINE IN

Continued on the next page

To keep discs clean

More about this unit

A dirty disc may not play correctly.

If a disc does become dirty, wipe it with

a soft cloth in a straight line from center

to edge.

Basic operations

Turning on the power

• Do not use any solvent (for example, conventional

record cleaner, spray, thinner, benzine, etc.) to clean

discs.

• By pressing SRC on the unit, you can also turn on the

power. If the source is ready, playback also starts.

Turning off the power

To play new discs

• If you turn off the power while listening to a disc, disc

play will start from where playback has been stopped

previously, next time you turn on the power.

• For MP3/WMA discs, playback will start from the

beginning of the last playing track.

New discs may have some rough spots

around the inner and outer edges. If

such a disc is used, this unit may reject

the disc.

To remove these rough spots, rub the edges with a

pencil or ball-point pen, etc.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

– Received stations are preset in No. 1 (lowest

frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in No. 1 will

be automatically tuned in.

Do not use the following discs:

Warped disc

Sticker

Sticker residue

• When storing a station manually, the previously

preset station is erased when a new station is stored

in the same preset number.

Stick-on label

Disc operations

Unusual shape

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply

with the “Compact Disc Digital Audio” standard.

Therefore, the use of Non-DVD side of a DualDisc on

this product may not be recommended.

Single CD (8 cm disc)

General

Playing a VCD disc

• This unit has been designed to reproduce CDs/CD

Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable)

in audio CD (CD-DA), MP3 and WMA formats.

• This unit cannot playback SVCD, DVDs, CD-Gs, or CD-I

discs.

• The PBC function is not available for some VCDs.

• The PBC function is automatically canceled when you

change the source or turn off the unit. Playback starts

from the beginning of the dics when you play the

VCD again.

• When a disc is inserted upside down, the disc

automatically ejects.

• While fast-forwarding or reversing on an MP3 or

WMA disc, you can only hear intermittent sounds.

• The On-Screen Display (OSD) will automatically

canceled when you change the source or turn off the

unit.

Playing an MP3/WMA disc

Playing a CD-R or CD-RW

• This unit can play back MP3/WMA files with the

extension code <.mp3> or <.wma> (regardless of

the letter case—upper/lower).

• This unit can show the names of albums, artists

(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or

2.4) for MP3 files.

• This unit can display only one-byte characters. No

other characters can be correctly displayed.

• This unit can play back MP3/WMA files meeting the

conditions below:

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can play back only files of the same type

which are first detected if a disc includes both audio

CD (CD-DA) files and MP3/WMA files.

• This unit can play back multi-session discs; however,

unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this

unit because of their disc characteristics, or for the

following reasons:

– Discs are dirty or scratched.

– Moisture condensation occurs on the lens inside

the unit.

– Bit rate: MP3: 32 kbps — 320 kbps

WMA: 48 kbps — 192 kbps

– Sampling frequency:

– The pickup lens inside the unit is dirty.

– CD-R/CD-RW on which the files are written with

“Packet Write” method.

48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)

24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)

48 kHz, 44.1 kHz, 32 kHz (for WMA)

– There are improper recording conditions (missing

data, etc.) or media conditions (stained, scratched,

warped, etc.).

• CD-RWs may require a longer readout time since the

reflectance of CD-RWs is lower than that of regular

CDs.

• Do not use the following CD-Rs or CD-RWs:

– Discs with stickers, labels, or a protective seal stuck

to the surface.

– Disc format: ISO 9660 Level 1/Level 2, Romeo,

Joliet, Windows long file name

• The maximum number of characters for file/folder

names vary among the disc format used (includes 4

extension characters—<.mp3> or <.wma>).

– ISO 9660 Level 1: up to 12 characters

– ISO 9660 Level 2: up to 31 characters

– Romeo: up to 40 characters

– Joliet: up to 40 characters

– Discs on which labels can be directly printed by an

ink jet printer.

– Windows long file name: up to 40 characters

Using these discs under high temperatures or high

humidities may cause malfunctions or damage to the

unit.

Continued on the next page

• This unit can play back files recorded in VBR (variable

bit rate).

General settings—PSM

• If you change the “AMP GAIN” setting from

“HIGH PWR” to “LOW PWR” while the volume level

is set higher than “VOL 30,” the unit automatically

changes the volume level to “VOL 30.”

Files recorded in VBR have a discrepancy in elapsed

time display, and do not show the actual elapsed

time. Especially, after performing the search function,

this difference becomes noticeable.

• This unit can recognize a total of 512 files, of 200

folders, and of 8 hierarchies.

• This unit cannot play back the following files:

– MP3 files encoded with MP3i and MP3 PRO format.

– MP3 files encoded in an inappropriate format.

– MP3 files encoded with Layer 1.

– WMA files encoded with lossless, professional, and

voice format.

– WMA files which are not based upon Windows

Media® Audio.

– WMA files copy-protected with DRM.

– Files which have the data such as WAVE, ATRAC3,

etc.

iPod or D. player operations

• When you turn on this unit, the iPod or D. player is

charged through this unit.

• While the iPod or D. player is connected, all

operations from the iPod or D. player are disabled.

Perform all operations from this unit.

• The text information may not be displayed correctly.

• If the text information includes more than 8

characters, it scrolls on the display. This unit can

display up to 40 characters.

Notice:

When operating an iPod or a D. player, some

operations may not be performed correctly or as

intended. In this case, visit the following JVC web

site:

For iPod users: <http://www.jvc.co.jp/english/

car/support/ks-pd100/index.html>

For D. player users: <http://www.jvc.co.jp/

english/car/support/ks-pd500/index.html>

• The search function works but search speed is not

constant.

Changing the source

• If you change the source, playback also stops

(without ejecting the disc).

Next time you select “DISC” for the playback source,

disc play starts from where it has been stopped

previously.

• For MP3/WMA discs, playback will start from the

beginning of the last playing track.

• Microsoft and Windows Media are either registered

trademarks or trademarks of Microsoft Corporation in

the United States and/or other countries.

• iPod is a trademark of Apple Inc., registered in the

U.S. and other countries.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds,

the disc is automatically inserted again into the

loading slot to protect it from dust. (Disc will not play

this time.)

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms

Remedies/Causes

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Check the cords and connections.

• The unit does not work at all.

Reset the unit (see page 2).

• SSM automatic presetting does not work. Store stations manually.

• Static noise while listening to the radio.

• Disc automatically ejects.

Connect the antenna firmly.

Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be

skipped.

• Insert a finalized CD-R/CD-RW.

• Finalize the CD-R/CD-RW with the component which you

used for recording.

• Disc can be neither played back nor

ejected.

• Unlock the disc (see page 13).

• Eject the disc forcibly (see page 2).

• Sound and pictures are sometimes

interrupted or distorted.

• Stop playback while driving on rough roads.

• Change the disc.

• Check the cords and connections.

• “NO DISC” appears on the display.

Insert a playable disc into the loading slot.

• No playback picture appears on the

monitor.

Parking brake wire is not connected properly.

(See Installation/Connection manual.)

• No picture appears on the monitor at all. • Connect the video cord correctly.

• Select a correct input on the monitor.

• Disc cannot be played back.

• Use a disc with MP3/WMA tracks recorded in the format

compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file

names.

• Noise is generated.

Skip to another track or change the disc. (Do not add the

extension code <.mp3> or <.wma> to non-MP3 or WMA

tracks.)

• A longer readout time is required (“CHECK” Do not use too many hierarchies and folders.

keeps flashing on the display).

Continued on the next page

Symptoms

Remedies/Causes

• Tracks do not play back in the order you

have intended them to play.

Playback order is determined when the files are recorded.

• Elapsed playing time is not correct.

This sometimes occurs during play. This is caused by how the

tracks are recorded on the disc.

• “NO FILES” appears on the display.

Insert a disc that contains MP3/WMA tracks.

• Correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers, and a

album name).

limited number of symbols.

Insert a disc into the magazine.

Insert the magazine.

• “NO DISC” appears on the display.

• “NO MAG” appears on the display.

• “RESET 8” appears on the display.

Connect this unit and the CD changer correctly and press the

reset button of the CD changer.

• “RESET 1” – “RESET 7” appears on the

display.

Press the reset button of the CD changer.

• The CD changer does not work at all.

Reset the unit (see page 2).

• The iPod or D. player does not turn on or • Check the connecting cable and its connection.

does not work.

• Update the firmware version.

• Charge the battery.

• Buttons do not work as intended.

• The sound is distorted.

The functions of the buttons have been changed. Press MODE

before performing the operation.

Deactivate the equalizer either on the unit or the iPod/

D. player.

• “NO IPOD” or “NO DP” appears on the

display.

• Check the connecting cable and its connection.

• Charge the battery.

• Playback stops.

The headphones are disconnected during playback. Restart

the playback operation using the control panel (see page 17).

• No sound can be heard when

connecting an iPod nano.

• Disconnect the headphones from the iPod nano.

• Update the firmware version of the iPod nano.

• No sound can be heard.

• “ERROR 01” appears on the display

when connecting a D. player.

Disconnect the adapter from the D. player. Then, connect it

again.

• “NO FILES” or “NO TRACK” appears on

the display.

No tracks are stored. Import tracks to the iPod or D. player.

• “RESET 1” – “RESET 7” appears on the

display.

Disconnect the adapter from both the unit and iPod/D. player.

Then, connect it again.

• “RESET 8” appears on the display.

Check the connection between the adapter and this unit.

• The iPod’s or D. player’s controls do not Reset the iPod or D. player.

work after disconnecting from this unit.

Specifications

AUDIO AMPLIFIER SECTION

VCD/CD PLAYER SECTION

Maximum Power Output:

Type:

Compact disc player

Front/Rear:

50 W per channel

Signal Detection

System:

Non-contact optical pickup

(semiconductor laser)

Continuous Power Output (RMS):

Number of Channels: 2 channels (stereo)

Frequency Response: 5 Hz to 20 000 Hz

Front/Rear:

19 W per channel into

4 Ω, 40 Hz to 20 000 Hz at

no more than 0.8% total

harmonic distortion.

Dynamic Range:

96 dB

Signal-to-Noise Ratio: 98 dB

Load Impedance:

Tone Control Range:

Bass:

4 Ω (4 Ω to 8 Ω allowance)

Wow and Flutter:

Less than measurable limit

MP3 Decoding Format: (MPEG1/2 Audio Layer 3)

10 dB at 100 Hz

10 dB at 10 kHz

40 Hz to 20 000 Hz

70 dB

2.5 V/20 kΩ load (full

scale)

Max. Bit Rate:

320 kbps

Treble:

WMA (Windows Media® Audio) Decoding Format:

Frequency Response:

Signal-to-Noise Ratio:

Line-Out Level/

Impedance:

Max. Bit Rate:

192 kbps

GENERAL

Power Requirement:

Output Impedance:

Other Terminal:

1 kΩ

LINE IN, CD changer

Operating Voltage: DC 14.4 V

(11 V to 16 V allowance)

Negative ground

VIDEO SECTION

Grounding System:

Color System:

PAL/NTSC

Allowable Operating 0°C to +40°C

Temperature:

Video Output (Composite): 1 Vp-p/75 Ω

Dimensions (W × H × D): (approx.)

TUNER SECTION

Frequency Range:

Installation Size:

Panel Size:

182 mm × 52 mm × 150 mm

188 mm × 58 mm × 11 mm

FM:

87.5 MHz to 108.0 MHz

Mass:

1.4 kg

(excluding accessories)

AM:

531 kHz to 1 602 kHz

FM Tuner

Usable Sensitivity:

Design and specifications are subject to change without

notice.

11.3 dBf (1.0 μV/75 Ω)

50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)

Alternate Channel

65 dB

Selectivity (400 kHz):

Frequency Response:

Stereo Separation:

AM Tuner

40 Hz to 15 000 Hz

30 dB

Sensitivity/Selectivity:

20 μV/35 dB

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

EN, TH

0207DTSMDTJEIN

KD-SV3305

Installation/Connection Manual

°“√µ¥µß/§¡Õ°“√µ¥µß

0207DTSMDTJEIN

EN, TH

GET0471-004A

[U/UH]

ENGLISH

‰∑¬

™¥ª√–°Õ∫π‰¥√∫°“√ÕÕ°·∫∫¡“‡æÕ„™ß“π°∫√–∫∫ °√–· ‰øø“ “¬¥π¢«≈∫°√–· µ√ß 12 ‚«≈∑ À“°√∂¬πµ¢Õß§≥‰¡‰

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does

not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

¥„™√–∫∫π µÕß„™‡§√Õß·ª≈ß°√–· ‰ø™«¬ ´ß “¡“√∂À“´Õ‰¥®“°√“π¢“¬‡§√Õß‡ ¬ß√∂¬πµ JVC

WARNINGS

§”‡µÕπ

• DO NOT install any unit in locations where;

• Õ¬“µ¥µß‡§√Õß„πµ”·Àπß∑;

– it may obstruct the steering wheel and gearshift lever operations.

– it may obstruct the operation of safety devices such as air bags.

– it may obstruct visibility.

^–– ^ÕÕ^““^®®^°°^¥¥¢^¢«^«“^“ß^ß°^°“^“√^√∑^∑”^”ß^ß“^“ππ¢^¢ÕÕ^ßß^æÕª^«ß°^¡√≥^“≈ª^¬Õ^·ß^≈°^–π^§§^π«^‡“^°¡^¬ª^√≈Õ¥¿¬ ‡™π ·Õ√·∫§

– Õ“®°¥¢«“ß “¬µ“

• DO NOT operate the unit while driving.

• If you need to operate the unit while driving, be sure to look ahead carefully.

• The driver must not watch the monitor while driving.

If the parking brake is not engaged, “PARKING” flashes on the display, and no playback

picture will be shown on the monitor.

– This warning appears only when the parking brake wire is connected to the parking brake

system built in the car.

• Õ¬“„™ß“π¢≥–¢∫¢

• ∂“®”‡ªπµÕß„™‡§√Õß¢≥–¢∫¢ ¢Õ„À¥∑“ß¢“ßÀπ“„À¥

• º¢∫µÕß‰¡¡Õß∑®Õ¡Õπ‡µÕ√¢≥–¢∫¢

À“°‰¡‰¥¢π‡∫√°¡Õ ¢Õ§«“¡ “PARKING” ®–°√–æ√∫∫π®Õ· ¥ßº≈ ·≈–®–‰¡¡√ª°“√‡≈π· ¥ß∫π®Õ¿“æ

– §”‡µÕππ®–ª√“°Æ¢π‡©æ“–‡¡ÕµÕ “¬‡∫√°°∫√–∫∫‡∫√°„π√∂¬πµ‰«‡∑“ππ

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all ‡æÕªÕß°π°“√‡°¥‰øø“≈¥«ß®√ ¢Õ·π–π”„Àª≈¥¢«·∫µ‡µÕ√≈∫ÕÕ° ·≈«®ßµÕ “¬‰ø°Õπµ¥µß‡§√Õß

electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

• µ√«® Õ∫„À·π„®«“‰¥‡¥π “¬¥πµÕ√–À«“ß‡§√Õß°∫µ«∂ß √∂¬πµ„À¡·≈«À≈ß®“°µ¥µß

À¡“¬‡Àµ:

Notes:

• „™æ°¥®”‡æ“–·∑πø« À“°ø« ¢“¥∫Õ¬ „Àª√°…“√“ π¢“¬‡§√Õß‡ ¬ß√∂¬πµ JVC

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio

dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both at

the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than

50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 16 of the

INSTRUCTIONS).

• ¢Õ·π–π”„ÀµÕ≈”‚æß ∑¡°”≈ß¢∫ ß ¥‡°π°«“ 50 W (∑ß¥“πÀπ“·≈–¥“πÀ≈ß ¡§“§«“¡µ“π∑“π 4 ∂ß 8 )

∂“°”≈ß¢∫µ”°«“ 50 W „À‡ª≈¬π§“ “AMP GAIN” ‡æÕªÕß°π‰¡„À≈”‚æß™”√¥ (¥Àπ“ 16 §”·π–π”)

• °“√ªÕß°π°“√≈¥«ß®√ ®–µÕßæπ¢« “¬µ–°« ∑‰¡„™·≈«¥«¬‡∑ ªæπ “¬‰ø

• ·ºπ√–∫“¬§«“¡√Õπ®–√Õπ¡“°À≈ß®“°„™ √–¡¥√–«ßÕ¬“‰ª ¡º ‡¡Õ∂Õ¥™¥ª√–°Õ∫π

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

Heat sink

·ºπ√–∫“¬§«“¡√Õπ

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit

will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

¢Õ§«√√–«ß”À√∫°“√µÕ·À≈ß®“¬°”≈ß·≈–≈”‚æß:

• Õ¬“µÕ “¬µ–°«‡§‡∫≈°”≈ß¢Õß≈”‚æß‡¢“°∫·∫µ‡µÕ√√∂¬πµ ¡©–ππ ™¥ª√–°Õ∫®–‰¥√∫§«“¡‡ ¬À“¬¡“°

• °Õπ∑®–µÕ“¬µ–°«‡§‡∫≈°”≈ß¢Õß≈”‚æß‡¢“°∫≈”‚æß „Àµ√«®Õ∫°“√‡¥π“¬‰ø≈”‚æß„π√∂¢Õß§≥„À‡√¬∫√Õ¬‡¬°Õπ

Parts list for installation and connection

√“¬°“√ «πª√–°Õ∫ ”À√∫µ¥µß·≈–‡™Õ¡µÕ°π

If any item is missing, consult your JVC car audio dealer immediately.

À“°¡ ß„¥‰¡§√∫ °√≥“ª√°…“µ«·∑π®”Àπ“¬‡§√Õß‡ ¬ßµ¥√∂¬πµ JVC ‚¥¬∑π∑

A / B

Hard case/Control panel

≈ß∫√√®/Àπ“ª¥

Sleeve

ª≈Õ°À¡

Trim plate

·ºπ‚≈À–¢Õ∫·µß

Power cord

“¬‡§‡∫≈°”≈ß

Crimp connector

¢«µÕ ”À√∫Àπ∫

Washer (ø5)

ª√–‡°π«ß·À«π (ø5)

Lock nut (M5)

πÕµ≈Õ§ (M5)

Mounting bolt (M5 × 20 mm)

≈°µ¥ (M5 × 20 ¡≈≈‡¡µ√)

Rubber cushion

¬“ß°π°√–·∑°

Handles

§π∫ß§∫

Remote controller

√‚¡µ§Õπ‚∑√≈

Battery

·∫µ‡µÕ√

INSTALLATION (IN-DASH MOUNTING)

°“√µ¥µß (°“√ª√–°Õ∫·ºßÀπ“ª∑¡‡¢“)

The following illustration shows a typical installation. If you have any questions or require information

regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

¿“æµ«Õ¬“ßµÕ‰ªπ· ¥ß∂ß°“√µ¥µß·∫∫∑«‰ª À“°§≥¡ª≠À“À√ÕµÕß°“√¢Õ¡≈‡°¬«°∫™¥µ¥µß °√≥“ª√°…“°∫º¢“¬‡§√Õß‡

¬ß√∂¬πµ JVC ¢Õß∑“πÀ√Õ∫√…

• ™¥ª√–°Õ∫ ∂“§≥‰¡·π„®«“µ¥µß™¥ª√–°Õ∫π∂°µÕßÀ√Õ‰¡ „ÀÀ“™“ßº‡™¬«™“≠‡ªπºµ¥µß

Do the required electrical connections.

µÕ “¬‰øµ“¡∑°”Àπ¥‰«∑ßÀ¡¥

Bend the appropriate tabs to hold the

sleeve firmly in place.

ßÕ·ºπ‡æÕ¬¥ª≈Õ°„ÀµÕ°π‡¢“∑

When using the optional stay / ‡¡Õ„™µ«¬¥·∫∫‡≈Õ°‰¥

When installing the unit without using the sleeve / ‡¡Õµ¥µß™¥ª√–°Õ∫‚¥¬‰¡„™ª≈Õ°À¡

In a Toyota car for example, first remove the car radio and install the unit in its place.

Stay (option)

µ«Õ¬“ß‡™π „π√∂¬πµ‚µ‚¬µ“ „À∂Õ¥«∑¬µ¥√∂¬πµÕÕ°°Õπ ·≈«®ßµ¥µß‡§√Õßπ‡¢“·∑π∑

µ«¬¥ (‡≈Õ°‰¥)

Fire wall

ºπß°π‰ø

Flat type screws (M5 × 8 mm)*²

°√À«‡√¬∫ (M5 × 8 ¡¡.)*²

^D·º^aß^shÀ^bπ^o“^aª^r∑^d¡

Bracket*²

·∑π√Õß√∫*²

Screw (option)

°√ (‡≈Õ°‰¥)

Flat type screws (M5 × 8 mm)*²

°√À«‡√¬∫ (M5 × 8 ¡¡.)*²

^P°–^o‡^cª^k“^e–^t

Bracket*²

·∑π√Õß√∫*²

Install the unit at an angle of less than 30˚.

Note

: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are

used, they could damage the unit.

µ¥µß™¥ª√–°Õ∫∑¡¡µ”°«“ 30˚ Õß»“

À¡“¬‡Àµ

‡¡Õµ¥µß™¥ª√–°Õ∫≈ß„π·∑π√Õß√∫‰« „À„™ °√¬“«¢π“¥ 8 ¡¡. ∂“„™ °√¬“«°«“πÕ“®∑”„À™¥ª√–°Õ∫‡ ¬À“¬‰¥

°“√∂Õ¥™¥ª√–°Õ∫

Removing the unit

Before removing the unit, release the rear section.

°Õπ®–∂Õ¥™¥ª√–°Õ∫ „Àª≈¥Àπ“µ¥ «π∑“¬°Õπ

Insert the two handles, then pull them as

illustrated so that the unit can be removed.

„§π∫ß§∫

Õπ≈ß„π√Õß”À√∫„™æπ≈«¥

¥ß¿“æ ®“°ππ „À‡≈Õπ™¥ª√–°Õ∫ÕÕ°

„π¢≥–∑§Õ¬ Ê¥ß§π∫ß§∫∑ß Õß ÕπÕÕ°®“°°π

When you stand the unit, be careful not to damage the fuse on the rear.

Not supplied for this unit.

*¹‡¡Õ§≥µß™¥ª√–°Õ∫¢π √–«ßÕ¬“∑”„Àø« ∫√‡«≥ «π∑“¬‡ ¬À“¬

*²‰¡‰¥„À¡“°∫™¥ª√–°Õ∫π

TROUBLESHOOTING

• The fuse blows.

°“√µ√«®Õ∫ª≠À“¢¥¢Õß

• ø« ú¢“¥

* Are the red and black leads connected correctly?

* ¡°“√‡™Õ¡ “¬µ–°« ¥”·≈– ·¥ßÕ¬“ß∂°µÕßÀ√Õ‰¡

• Power cannot be turned on.

• ‰¡ “¡“√∂‡ª¥‡§√Õß‰¥

* ¡°“√‡™Õ¡ “¬µ–°« ‡À≈ÕßÀ√Õ‰¡

* Is the yellow lead connected?

• ‰¡¡‡ ¬ßÕÕ°®“°≈”‚æß

• No sound from the speakers.

* “¬µ–°« «π∑ÕÕ°∑“ß≈”‚æß‡°¥‰øø“≈¥«ß®√À√Õ‰¡

* Is the speaker output lead short-circuited?

• ‡ ¬ß‡æ¬π

• Sound is distorted.

* “¬µ–°« «π∑ÕÕ°∑“ß≈”‚æßµÕ≈ß¥πÀ√Õ‰¡

* “¬¢«≈∫ “–” ¢Õß≈”‚æß¥“π´“¬ (L) ·≈–¢«“ (R) µÕ≈ß¥πµ“¡ª°µÀ√Õ‰¡

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• ‡ ¬ß√∫°«π

• Noise interfere with sounds.

* ¡°“√„™ “¬ πÊ À√ÕÀπ“Ê µÕ®“°‡§√Õß «π∑µ¥µß ‰«∫πæπ¥“πÀ≈ß°∫µ«∂ß√∂¬πµÀ√Õ‰¡

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• ™¥ª√–°Õ∫√Õπ¢π

• This unit becomes hot.

* “¬µ–°« «π∑ÕÕ°∑“ß≈”‚æßµÕ≈ß¥πÀ√Õ‰¡

* “¬¢«≈∫ “–” ¢Õß≈”‚æß¥“π´“¬ (L) ·≈–¢«“ (R) µÕ≈ß¥πµ“¡ª°µÀ√Õ‰¡

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• ‡§√Õß√∫π∑”ß“π‰¡

• This unit does not work at all.

* ∑“π‰¥µß‡§√Õß„À¡À√Õ¬ß

* Have you reset your unit?

ENGLISH

‰∑¬

ELECTRICAL CONNECTIONS

°“√‡™Õ¡‚¥¬„™‰øø“

Typical connections / °“√‡™Õ¡µÕ·∫∫ª°µ

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious

damage to this unit.

The leads of the power cord and those of the connector from the car body may be different in color.

°Õ•∑”°“•‡™•Õ¡µÕ: µ•«®†Õ•°“•‡¥•†“¬‰ø„•••¬•µÕ¬“ß•–¡¥•–«Õ¬“„Àº¥æ•“¥„•°“•‡™•Õ¡µÕ™¥ª•–°Õ•™¥•

°“•‡™•Õ¡µÕº¥æ•“¥Õ“®∑”„À‡°¥§«“¡‡ ¬À“¬•“¬·•ß°•™¥ª•–

°Õ••‰¥“•µ–°«¢Õß†“¬‰ø ·•–¢ÕßÕª°••µÕ‡™•Õ¡®“°µ«• ß••Õ“®¡ ∑‰¡‡À¡•Õ•°•

1 µÕ “¬‰ø µ“¡≈”¥∫∑√–∫„π√ª¥“π≈“ß

1 Connect the colored leads of the power cord in the order specified in the illustration below.

2 Connect the antenna cord.

3 Finally connect the wiring harness to the unit.

2 ‡™Õ¡µÕ°∫“¬Õ“°“»

3 ¥∑“¬ µÕ «π§«∫§¡°“√‡¥π “¬‰ø‡¢“°∫™¥ª√–°Õ∫™¥π

LINE IN

(see diagram / ¥·ºπ¿¡

)

Line out (see diagram

)

VIDEO OUT

“¬ÕÕ° (¥·ºπ¿¡

)

(see diagram / ¥·ºπ¿¡

)

Rear ground terminal

®¥‡™Õ¡µÕ “¬¥π¥“πÀ≈ß

15 A fuse

ø« ¢π“¥ 15 A

Antenna terminal

To external components

(see diagram

)

¢«µÕ “¬Õ“°“»

™Õß‡ ¬∫µÕ¢ÕßÕª°√≥¿“¬πÕ°

Ignition switch

(¥·ºπ¿¡

)

Black

¥”

«∑™®¥√–‡∫¥

To metallic body or chassis of the car

µÕ°∫‚§√ß‚≈À–À√Õ‡™´ ¢Õß√∂¬πµ

Yellow *²

‡À≈Õß *²

To a live terminal in the fuse block connecting to the car battery

(bypassing the ignition switch) (constant 12 V)

µµÕ°∫¢«∑¡°√–·‰øø“„π·ºßø« ´ßµÕ°∫·∫µ‡µÕ√√∂¬πµ

(‚¥¬‰¡µÕß„™« ∑™®¥√–‡∫¥) (12 ‚«≈∑§ß∑)

To an accessory terminal in the fuse block

Red

·¥ß

µÕ°∫¢« «πª√–°Õ∫„π·ºßø«

Fuse block

·ºßø«

Blue

»ø“

To the automatic antenna if any (250 mA max.)

‡ “Õ“°“»‰øø“Õµ‚π¡µ À“°¡ (¢π“¥ ß ¥ 250 mA)

Blue with white stripe

π”‡ßπ≈“¬¢“«

To the remote lead of other equipment (200 mA max.)

µÕ‡¢“°∫Õª°√≥Õπ (¢π“¥ ß ¥ 200 mA)

Brown

π”µ“≈

To cellular phone system

µÕ°∫‚∑√»æ∑‡§≈Õπ∑

Light green

‡¢¬«ÕÕπ

To parking brake, metallic body or chassis of the car

µÕ°∫‡∫√°¡Õ µ«∂ß∑‡ªπ‚≈À– À√Õ‚§√ß√∂¬πµ

White with black stripe

Gray with black stripe

Gray

Green with black stripe

Green

Purple with black stripe

Purple

White

¢“«·∂∫¥”

‡∑“·∂∫¥”

‡∑“

‡¢¬«·∂∫¥”

‡¢¬«

¡«ß·∂∫¥”

¡«ß

¢“«

Left speaker (front)

Right speaker (front)

Left speaker (rear)

Right speaker (rear)

≈”‚æß´“¬ (Àπ“)

≈”‚æß¢«“ (Àπ“)

≈”‚æß´“¬ (À≈ß)

≈”‚æß¢«“ (À≈ß)

Connecting the parking brake wire / µÕ “¬‡∫√°¡Õ

When installing the monitor in a location where it can be seen by the driver

Connect the parking brake wire to the parking brake system built in the car.

¡Õ®–µ¥µß®Õ¡Õπ‡µÕ√„πµ”·Àπß∑º¢∫ “¡“√∂¡Õß‡Àπ‰¥

When installing the monitor in a location where it cannot be

seen by the driver

Connect the parking brake wire to metallic body or chassis of the car.

‡¡Õ®–µ¥µß®Õ¡Õπ‡µÕ√„πµ”·Àπß∑º¢∫‰¡ “¡“√∂¡Õß‡Àπ‰¥

µÕ “¬‡∫√°¡Õ°∫µ«∂ß∑‡ªπ‚≈À–À√Õ‚§√ß√∂¬πµ

µÕ “¬‡∫√°¡Õ°∫√–∫∫‡∫√°¡Õ¢Õß√∂¬πµ

Parking brake wire (light green)

“¬‡∫√°¡Õ ( ‡¢¬«ÕÕπ)

Parking brake

‡∫√°¡Õ

Parking brake wire (light green)

“¬‡∫√°¡Õ ( ‡¢¬«ÕÕπ)

To metallic body or chassis of the car

µÕ°∫‚§√ß‚≈À–À√Õ‡™´ ¢Õß√∂¬πµ

Parking brake switch (inside the car)

«µ™‡∫√°¡Õ (¿“¬„π√∂)

Connecting the crimp connector / «∏µÕ¢«µÕ ”À√∫Àπ∫

Wire connecting the battery and the parking brake switch.

Contact the metallic part of the crimp to the wires inside.

„À «π∑‡ªπ‚≈À–¢Õßµ«Àπ∫ ¡º °∫ “¬¢“ß„π

“¬∑µÕ°∫·∫µ‡µÕ√·≈– «µ™‡∫√°¡Õ

Pinch the crimp firmly.

Àπ∫„À·ππ

Attach the parking brake wire to this point.

Õ “¬‡∫√°¡Õ∑®¥π

*¹‰¡‰¥„À¡“°∫™¥ª√–°Õ∫π

Not supplied for this unit.

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power

cannot be turned on.

°Õπ°“√µ√«® Õ∫°“√∑”ß“π¢Õß™¥ª√–°Õ∫π°Õπ∑®–µ¥µß µÕßµÕ “¬µ–°«π°Õπ ¡©–ππ®–‰¡ “¡“√∂‡ª¥‡§√Õß‰¥

Connecting the monitor / °“√µÕ®Õ¿“æ

Video cord*³

“¬«¥‚Õ*³

or / À√Õ

Rear side

¥â“πÀ≈ß

KV-MR9010

9-INCH WIDESCREEN MONITOR*³

¡Õπ‡µÕ√ ®Õ°«“ß 9 π«*³

Connecting the external amplifier / °“√µÕ‡æ¡‡µ¡‡¢“°∫Õª°√≥ÕπÊ

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it

can be controlled through this unit.

§≥“¡“√∂µÕ°∫·Õ¡æ≈ø“¬‡ÕÕ√ · –Õª°√≥ÕπÊ‰¥ ‡æÕ‡æ¡§≥ ¿“æ‡ ¬ß„À°∫√–∫∫ ‡µÕ√‚Õ¢Õß√∂¬πµ

• µÕ “¬µ–°«√–¬–‰°≈ ( π”‡ßπ≈“¬¢“«) ‡¢“°∫ “¬µ–°«√–¬–‰°≈¢ÕßÕª°√≥Õπ Ê ‡æÕ®– “¡“√∂§«∫§¡‚¥¬™¥ª√–

°Õ∫π‰¥

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker

leads of this unit unused.

• ∂Õ¥≈”‚æßÕÕ°®“°™¥ª√–°Õ∫π ·≈«µÕ‡¢“°∫‡§√Õß¢¬“¬ ∑ß “¬µ–°«≈”‚æß¢Õß™¥ª√–°Õ∫π‰«

Y-connector*³

¢ÕµÕ√ªµ« Y*³

Remote lead

“¬µ–°«•–¬–‰°•

Remote lead (blue with white stripe)

“¬µ–°«•–¬–‰°• ( π”‡ßπ≈“¬¢“«)

Rear speakers

≈”‚æßÀ≈ß

To the remote lead of other equipment or

automatic antenna if any

µÕ “¬°∫Õª°√≥ÕπÀ√Õ‡ “Õ“°“»Õµ‚π¡µ∂“¡

JVC Amplifier

‡§√Õß¢¬“¬‡ ¬ß JVC

Front speakers

≈”‚æßÀπ“

Connecting the external components / °“√µÕ‡æ¡‡µ¡‡¢“°∫Õª°√≥ÕπÊ

^{JVC CD changer, Apple iPod, or JVC D. player / JVC CD}‡™π‡®Õ√, Apple iPod À√Õ‡§√Õß‡≈π JVC D.

• Set “CHANGER” for the external input setting (See page 16 of the INSTRUCTIONS.) / µß§“ “CHANGER” ‡ªπ°“√§“√∫ ≠≠“≥Õª°√≥¿“¬πÕ° (¥Àπ“ 16 §”·π–π”)

You can connect these components as illustrated below. The iPod or D. player can be connected using

an interface adapter (not supplied)—KS-PD100 (for iPod) or KS-PD500 (for D. player).

∑“π “¡“√∂µÕÕª°√≥¥ß°≈“«µ“¡¿“æ· ¥ß¥“π≈“ß ∑“π “¡“√∂‡™Õ¡µÕ iPod À√Õ‡§√Õß‡≈π D. ‚¥¬„™Õπ‡∑Õ√‡ø Õ–

·¥ª‡µÕ√ (‰¡¡¡“„À)—KS-PD100 ( ”À√∫ iPod) À√Õ KS-PD500 ( ”À√∫‡§√Õß‡≈π D.)

CAUTION

¢Õ§«√√–«ß

Before connecting the external components, make sure that the unit is turned off.

°Õπ®–‡™Õ¡µÕ°∫Õª°√≥¿“¬πÕ° °√≥“µ√«® Õ∫„À·π„®«“ªî¥‡§√ÕßÕ¬

JVC CD changer

JVC CD ‡™π‡®Õ√

CD changer jack

or / À√Õ

™Õß‡ ¬∫µÕ¢Õß‡§√Õß‡≈π CD

Apple iPod

or /À√Õ

iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

iPod ‡ªπ‡§√ÕßÀ¡“¬°“√§“¢Õß Apple Computer, Inc. ´ß®¥∑–‡∫¬π°“√§“„π

ª√–‡∑ » À√∞Õ‡¡√°“·≈–ª√–‡∑»ÕπÊ

JVC D. player

‡§√Õß‡≈π JVC D.

Other external component / Õª°√≥¿“¬πÕ°ÕπÊ

• ^{Set “EXT IN” for the external input setting (See page 16 of the INSTRUCTIONS.) /}µß§“ “EXT IN”

‡∫ªπ°“√§“√∫ ≠≠“≥Õª°√≥¿“¬πÕ° (¥Àπ“ 16 §”·π–π”)

External component

Õª°√≥¿“¬πÕ°

CD changer jack

™Õß‡ ¬∫µÕ¢Õß

‡§√Õß‡≈π ^CD

3.5 mm stereo mini plug

¢«‡ ¬∫¡π ‡µÕ√‚Õ¢π“¥ 3.5 ¡¡.

À√Õ

External component

Õª°√≥¿“¬πÕ°

*³‰¡‰¥„À¡“°∫™¥ª√–°Õ∫π

Not supplied for this unit.

Signal cord (not supplied for this unit).

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint

(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the

unit.

Connecting cord supplied for your CD changer.

Line Input Adapter KS-U57 (not supplied for this unit).

AUX Input Adapter KS-U58 (not supplied for this unit).

*⁴“¬‡§‡∫≈ ≠≠“≥ (‰¡‰¥„À¡“°∫™¥ª√–°Õ∫π)

µÕ≈«¥ “¬¥π„À·ππ‡¢“°∫µ«∂ß‡À≈° À√Õµ«∂ß√∂

—

µ√ß «π ∑‰¡¡ ‡§≈Õ∫ (À“°¡ ‡§≈Õ∫Õ¬ „À¢¥ ÕÕ°°Õπ

°ÕπµÕ≈«¥ “¬¥π) À“°‰¡ªØ∫µµ“¡§”·π–π”π ‡§√ÕßÕ“®™”√¥ À√Õ‡ ¬À“¬‰¥

*⁶µÕ “¬∑„À¡“ ”À√∫ CD ‡™π‡®Õ√

*⁷Õ·¥ª‡µÕ√ “¬ ≠≠“≥‡¢“ KS-U57 (‰¡‰¥„À¡“°∫™¥ª√–°Õ∫π)

*⁸Õ–·¥ª‡µÕ√√∫ ≠≠“≥ AUX √π KS-U58 (‰¡‰¥„À¡“°∫™¥ª√–°Õ∫π)

VCD/CD RECEIVER

KD-SV3305

ALAT PENERIMA VCD/CD

For canceling the display demonstration, see page 7.

Untuk membatalkan tampilan demonstrasi, lihat halaman 7.

For installation and connections, refer to the separate manual.

Untuk instalasi dan penyambungan, lihat buku pedoman terpisah.

INSTRUCTIONS

BUKU PETUNJUK

GET0471-007A

[UN]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to

qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical

instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

WARNINGS:

To prevent accidents and damage

[European Union only]

• DO NOT install any unit in locations where;

– it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety

devices such as air bags.

How to reset your unit

– it may obstruct visibility.

• DO NOT operate the unit while driving.

• If you need to operate the unit while

driving, be sure to look ahead carefully.

• The driver must not watch the monitor

while driving.

If the parking brake is not engaged,

• Your preset adjustments will also be erased.

“PARKING” flashes on the display, and

no playback picture will be shown on the

monitor.

How to forcibly eject a disc

– This warning appears only when the

parking brake wire is connected to the

parking brake system built in the car

(refer to the Installation/Connection

Manual).

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

The following marks are used to indicate...

: Built-in VCD/CD player operations.

: External CD changer operations.

CONTENTS

Control panel ..................................

Remote controller—^RM-RK120.............

: Indicator displayed for the

corresponding operation.

Getting started................................

Basic operations...................................................

How to use the MODE button

If you press MODE, the unit goes into functions mode,

then the number buttons (except “1” and “4”) and

Radio operations .............................

Disc operations................................

Playing a disc in the unit .....................................

/¢ buttons work as different function

buttons.

Playing discs in the CD changer ........................... 10

Sound adjustments.......................... 14

General settings—PSM ................... 15

iPod/D. player operations................. 17

Ex.: When number button 2 works as

MO (monaural) button.

Other external component

operations ................................... 19

To use these buttons for their original functions

again after pressing MODE, wait for 5 seconds

without pressing any of these buttons until the

functions mode is cleared or press MODE again.

Maintenance ................................... 19

More about this unit ........................ 20

Troubleshooting.............................. 23

Specifications.................................. 25

Detaching the control panel

For safety...

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car...

Attaching the control panel

If you have parked the car for a long time in hot or cold

weather, wait until the temperature in the car becomes

normal before operating the unit.

Control panel

Parts identification

Display window

1 4 /¢ buttons

;

DISP (display) button

(standby/on attenuator) button

(control panel release) button

Disc information indicators—TAG (ID3 Tag),

(folder), (track/file)

Disc type indicators—WMA, MP3

Playback source indicators—

Remote sensor

DO NOT expose the remote sensor to strong light

(direct sunlight or artificial lighting).

Loading slot

Display window

CH: Lights up only when CD-CH is selected as the

playback source.

6 0 (eject) button

EQ (equalizer) button

SRC (source) button

BAND button

6 (play/pause) button

Control dial

DISC: Lights up for the built-in CD player.

Playback mode / item indicators— RND (random),

(disc), (folder), RPT (repeat)

LOUD (loudness) indicator

EQ (equalizer) indicator

SEL (select) button

Sound mode (C-EQ: custom equalizer) indicators—

JAZZ, CLASSIC, HIP HOP, POPS, ROCK, USER

Tr (track) indicator

Source display / Volume level indicator

Main display

MO (monaural) button

SSM (Strong-station Sequential Memory) button

Number buttons

RPT (repeat) button

RND (random) button

MODE button

Tuner reception indicators—ST (stereo),

MO (monaural)

Main elements and features

Remote controller—

RM-RK120

Installing the lithium coin battery

(CR2025)

Aim the remote controller directly at the remote

sensor on the unit. Make sure there is no obstacle

in between.

Warning:

• Do not install any battery other than CR2025 or

its equivalent; otherwise, it may explode.

• Do not leave the remote controller in a place

(such as dashboards) exposed to direct sunlight

for a long time; otherwise, it may explode.

• Store the battery in a place where children

cannot reach to avoid risk of accident.

• To prevent the battery from over-heating,

cracking, or starting a fire:

– Do not recharge, short, disassemble, heat the

battery, or dispose of it in a fire.

– Do not leave the battery with other metallic

materials.

SOURCE button

• Selects the playback source.

(standby/on attenuator) button

• Turns the power on if pressed briefly or

attenuates the sound when the power is on.

• Turns the power off if pressed and held.

3 2 REV (reverse) / FWD (forward) 3 buttons

• Searches for stations if pressed briefly.

• Fast-forwards or reverses the track if pressed and

held.

– Do not poke the battery with tweezers or similar

tools.

– Wrap the battery with tape and insulate when

throwing away or saving it.

• Changes the tracks if pressed briefly.

• While listening to an Apple iPod or a JVC

D. player (in menu selecting mode):

– Selects an item if pressed briefly. (Then, press

DOWN ∞ to confirm the selection.)

– Skips 10 items at a time if pressed and held.

Continued on the next page

VOL. + / – buttons

• Adjusts the volume level.

ENTER and number buttons

PBC (Playback Control) button

• Activates or deactivates the PBC function.

RETURN button

• Selects a track/file directly.

• Returns to the previous menu while playing a

VCD in PBC function.

OSD (On-Screen Display) button

• Turn on and off the OSD on the monitor.

AUDIO button

– Press the number button(s), then press ENTER.

– Not used for iPod/D. player operations.

• Selects an item from the menu while playing

back a Video CD (VCD) in Playback Control (PBC)

function.

• Selects the audio channel for VCD playback.

– Press the number button(s), then press ENTER.

• Selects the discs while operating the CD changer.

– To select disc number 1 – 6, press number

button 1 – 6 briefly.

* 5 UP

: Returns to the previous menu.

DOWN ∞ : Confirms the selection.

– To select disc number 7 – 12, press and hold

number button 1 (7) – 6 (12).

EQ (equalizer) button

• Selects the sound mode (C-EQ: custom

equalizer).

BAND 6 button

• Changes the FM/AM bands.

• Stops disc playback temporarily. To resume

playback, press the button again.

– While playing a VCD, the playback scene at the

moment stops and remain still.

– Not used for CD changer, iPod, or D. player

operations.

8 5 UP / DOWN ∞ buttons

• Changes the preset stations.

• Changes the folder of the MP3/WMA discs if

pressed briefly.

• Changes the disc while operating the CD changer

if pressed and held.

• While listening to an iPod or a D. player:

– Pauses/stops or resumes playback with

DOWN ∞.

– Enters the main menu with 5 UP.

(Now 5 UP / DOWN ∞/2 REV / FWD 3 work

as the menu selecting buttons.)*

To drop the volume in a

moment (ATT)

To restore the sound, press the

button again.

Getting started

Basic operations

To turn off the power

~ Turn on the power.

Basic settings

• See also “General settings — PSM” on pages 15 and

16.

* You cannot select these sources if they are not

ready or not connected.

! For FM/AM tuner

1 Canceling the display demonstrations

Select “DEMO,” then “DEMO OFF.”

2 Setting the clock

Select “CLOCK H” (hour), then adjust the hour.

Select “CLOCK M” (minute), then adjust the

minute.

⁄ Adjust the volume.

Finish the procedure.

Volume level appears.

To check the current clock time while the

power is turned off

@ Adjust the sound as you want. (See

page 14.)

Caution on volume setting:

Discs produce very little noise compared with other

sources. Lower the volume before playing a disc

to avoid damaging the speakers by the sudden

increase of the output level.

When an FM stereo broadcast is hard to

receive

Radio operations

Lights up when monaural mode is activated.

Reception improves, but stereo effect will be lost.

To restore the stereo effect, repeat the same

procedure. “MONO OFF” appears and the MO indicator

goes off.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

! Start searching for a station.

Storing stations in memory

You can preset six stations for each band.

When a station is received, searching stops.

To stop searching, press the same button

again.

FM station automatic presetting—

SSM (Strong-station Sequential

Memory)

Select the FM band (FM1 – FM3) you want to

store into.

To tune in to a station manually

In step ! above...

Select a desired station frequency.

“SSM” flashes, then disappears when automatic

presetting is over.

Local FM stations with the strongest signals are

searched and stored automatically in the FM band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset number

4 of the FM1 band.

Disc operations

Playing a disc in the unit

All tracks will be played repeatedly until you change the

source or eject the disc.

• If a disc menu appears on the monitor while playing a

VCD with PBC, see page 11.

Preset number flashes for a while.

Before performing any operations, make sure the

following....

• Turn on the monitor and select the appropriate

monitor input before playing a VCD.

• If you turn on the monitor, you can also control the

MP3/WMA playback by referring to the monitor

screen (see page 12).

Listening to a preset station

Select the preset station (1 – 6) you want.

• Select the video system suitable for your monitor (see

page 16).

To stop play temporarily

To resume playback, press the

button again.

To check the other information while

listening to the radio

To stop play and eject the

disc

Clock Ô Frequency

Continued on the next page

To fast-forward or reverse the track

To go to the next or previous tracks

Playing discs in the CD changer

All discs in the magazine will be played repeatedly until

you change the source.

• Ejecting the magazine will also stop playing.

* If you have changed the external input setting

to “EXT IN” (see page 16), you cannot select the

CD changer.

To go to the next or previous folders (only for

MP3 or WMA discs)

Ÿ Select a disc.

For disc number from 01 – 06:

For MP3 discs:

For WMA discs:

For disc number from 07 – 12:

About MP3 and WMA discs

MP3 and WMA “tracks” (words “file” and “track” are

used interchangeably) are recorded in “folders.”

To locate a particular track (for CD or VCD

with PBC set to “PBC OFF”) or folder (for MP3

or WMA discs) directly

To select a number from 01 – 06:

About the CD changer

It is recommended to use a JVC MP3-compatible CD

changer with your unit.

• You can also connect MP3-incompatible CD changers.

However, these units are not compatible with MP3

discs.

To select a number from 07 – 12:

• You cannot use the CH-X99, CH-X100, and KD-MK

series CD changers with this unit.

• You cannot control and play any WMA or VCD disc in

the CD changer.

• Disc text information recorded in the CD Text can be

displayed when a JVC CD Text compatible CD changer

is connected.

• For connection, see Installation/Connection Manual

(separate volume).

• To use direct folder access on MP3/WMA discs, it

is required that folders are assigned with 2-digit

numbers at the beginning of their folder names—

01, 02, 03, and so on.

To select a particular track in a folder

(for MP3 or WMA discs):

Playback Control (PBC) operations

On-Screen (OSD) information

This operation is only possible when using the

remote controller.

This operation is only possible when using the

remote controller.

While playing a VCD....

PBC ON Ô PBC OFF

You can check the track number and elapsed playing

time if the monitor is turned on.

While playing a disc....

• To turn off the On-Screen Display,

press the button again.

PBC ON : A menu appears on the monitor.

PBC OFF: Cancels.

Current/total track number

Elapsed playing time

• A menu may be a list of items, submenus, or

some moving pictures.

Select the item you want.

Selecting the audio channel

This operation is only possible when using the

remote controller.

• To select an item from the submenus, repeat this

step.

You can select the audio channel to play. (This is

convenient when playing a Karaoke VCD.)

The selected item starts playback automatically.

To correct a mis-entry and to return to the

previous menu

STEREO : To listen to normal stereo (left/right)

playback.

MONO L : To listen to the L (left) audio channel.

MONO R : To listen to the R (right) audio channel.

• The audio channel is automatically set to “STEREO”

when you change the disc or source.

To select a folder

To select a track

MP3/WMA control screen operations

You can also control the playback of an MP3/WMA disc

by referring to the monitor.

• The control screen automatically appears on the

monitor when you insert an MP3/WMA disc.

• Pressing these buttons repeatedly can also select

tracks from the previous/next folders.

• See also page 10 for using the buttons on the control

panel to select a folder or track.

Selecting the playback modes

You can use only one of the following playback modes

at a time.

• For VCD: While PBC (see page 11) is not in use.

Artiste name* (only for MP3 discs)

• The artiste name will scroll on the monitor if it

cannot be shown at a time.

Operation mode—PLAY, PAUSE, FF (fast-forward),

FR (fast-reverse), SELECT (selected track number),

REPEAT TRACK, REPEAT FOLDER, REPEAT OFF,

RANDOM FOLDER, RANDOM DISC, RANDOM OFF

• Operation mode appears for a while on the

monitor.

Select your desired playback mode.

Repeat play

Folder name*

Track title* (only for MP3 discs)

• The track title will scroll on the monitor if it

cannot be shown at a time.

Mode

Plays repeatedly

TRK RPT : The current track.

Highlighted bar for the current file name*

OSD indication—Current/total track number,

Elapsed playing time

• Appears only if you turn on the OSD (see page

11).

FLDR RPT*¹: All tracks of the current folder.

DISC RPT*²: All tracks of the current disc.

RPT OFF : Cancels.

Current list/total list number

Track list

• The monitor can show 12 tracks at a time and a

maximum of 239 tracks for a disc.

* Some symbols will not be shown (and will be

substituted or blanked) on the control screen.

• For MP3 disc : When “TAG DISP” is set to “TAG OFF”

• For WMA disc :

Random play

Mode

Plays at random

FLDR RND*¹: All tracks of the current folder,

then tracks of the next folder and

so on.

: Clock with the current track number

: Elapsed playing time with the current track

number

DISC RND : All tracks of the current disc.

MAG RND*²: All tracks of the inserted discs.

If the current disc is an audio CD or a VCD, “NO NAME”

appears.

Only for the built-in CD player.

If an MP3 file does not have Tag information, folder

name and file name appear. In this case, the TAG

indicator will not light up.

RND OFF

: Cancels.

Only while playing an MP3 or a WMA disc.

Only while playing discs in the CD changer.

Other main functions

Prohibiting disc ejection

You can lock a disc in the loading slot.

Changing the display information

While playing an audio CD, a CD Text, or a VCD

with PBC set to “PBC OFF” (see page 11)

To cancel the prohibition, repeat the same

procedure.

While playing an MP3 or a WMA*²disc

• Only for MP3 disc : When “TAG DISP” is set to

“TAG ON” (see page 16)

Adjusting the sound

Sound adjustments

You can select a preset sound mode suitable to the

music genre (C-EQ: custom equalizer).

You can adjust the sound characteristics to your

preference.

Preset values

BAS

TRE

LOUD

(bass) (treble) (loudness)

Indication (For)

USER

(Flat sound)

+03 +01

+01 –02

+04 +01

+02 00

+02 +03

OFF

Indication [Range]

ROCK

(Rock or disco music)

BAS*¹(bass)

Adjust the bass. [–06 to +06]

CLASSIC

(Classical music)

OFF

TRE*¹(treble)

Adjust the treble. [–06 to +06]

POPS

(Light music)

FAD*²(fader)

Adjust the front and rear speaker balance. [R06 to F06]

HIP HOP

(Funk or rap music)

BAL (balance)

Adjust the left and right speaker balance.

[L06 to R06]

JAZZ

(Jazz music)

OFF

LOUD*¹(loudness)

Boost low and high frequencies to produce a well-

balanced sound at low volume level.

[LOUD ON or LOUD OFF]

VOL (volume)

Adjust the volume. [00 to 30 or 50*³]

When you adjust the bass, treble, or loudness, the

adjustment you have made is stored for the currently

selected sound mode (C-EQ) including “USER.”

If you are using a two-speaker system, set the fader

level to “00.”

Depending on the amplifier gain control setting. (See

page 16 for details.)

General settings — PSM

You can change PSM (Preferred Setting Mode) items listed in the table that follows.

Repeat steps 2 and 3 to adjust other PSM

items if necessary.

Select a PSM item.

Finish the procedure.

Adjust the PSM item selected.

Indications

DEMO

Item

Setting, [reference page]

(

: Initial)

• DEMO ON

Display demonstration will be activated automatically if no

operation is done for about 20 seconds, [7].

Cancels.

Display demonstration

• DEMO OFF

CLOCK H

1 – 12

[Initial: 1 (1:00)], [7]

Hour adjustment

CLOCK M

00 – 59

[Initial: 00 (1:00)], [7]

Minute adjustment

DIMMER

Dimmer

• ON

• OFF

Dims the display illumination of this unit.

Cancels.

TEL

• MUTING 1/

MUTING 2:

• OFF

Select either one which mutes the sounds while using a cellular

phone.

Cancels.

Telephone muting

Continued on the next page

Indications

Item

Setting, [reference page]

(

: Initial)

SCROLL *¹

Scroll

• ONCE

• AUTO

• OFF

Scrolls the track information once.

Repeats scrolling (at 5-second intervals).

Cancels.

• Pressing DISP for more than one second can scroll the display

regardless of the setting.

TAG DISP

Tag display

• TAG ON

• TAG OFF

Shows the Tag information while playing MP3 tracks, [13].

Cancels.

AMP GAIN

Amplifier gain control

• LOW PWR

VOL 00 – VOL 30 (Select this if the maximum power of the speaker

is less than 50 W to prevent damaging the speaker.)

VOL 00 – VOL 50

• HIGH PWR

VIDEO

Video system

• PAL

• NTSC

Select this if your monitor is of the PAL color system.

Select this if your monitor is of the NTSC color system.

• Press SEL to activate the selection before you select the other PSM

items to adjust.

EXT IN *²

External input

• CHANGER

To use a JVC CD changer, [10], an Apple iPod or a JVC D. player,

[17].

To use any other external component than the above, [19].

• EXT IN

Some characters or symbols will not be shown correctly (or will be blanked) on the display.

Displayed only when one of the following sources is selected—FM, AM, DISC, or LINE IN.

To pause*¹or stop*²playback

iPod/D. player operations

This unit is ready for operating an Apple iPod or a JVC

D. player from the control panel.

To resume playback, press 4 after pressing

MODE.

Before operating your iPod or D. player:

Connect either one of the following (separately

purchased) to the CD changer jack on the rear of this

unit.

• Interface adapter for iPod—KS-PD100 for

controlling an iPod.

To fast-forward or reverse the track

To go to the next or previous tracks

• D. player interface adapter—KS-PD500 for

controlling a D. player.

• For connection, see Installation/Connection Manual

(separate volume).

• For details, refer also to the manual supplied with the

interface adapter.

For iPod

For D. player

Preparations:

Make sure “CHANGER” is selected for the external input

setting, see page 16.

Playback starts automatically from where it has

been paused*¹or stopped*²previously.

! Adjust the volume.

⁄ Adjust the sound as you want. (See

page 14.)

Continued on the next page

Selecting a track from the menu

Selecting the playback modes

Enter the main menu.

Select your desired playback mode.

Now the 4 /¢ buttons

work as the menu selecting buttons*.

Repeat play

Select the desired menu.

ONE RPT

Functions the same as “Repeat One” of the iPod or

“Repeat Mode = One” for the D. player.

ALL RPT

For iPod:

Functions the same as “Repeat All” of the iPod or

“Repeat Mode = All” for the D. player.

PLAYLIST Ô ARTISTS Ô ALBUMS Ô

SONGS Ô GENRES Ô COMPOSER Ô

(back to the beginning)

RPT OFF

Cancels.

For D. player:

Random play

PLAYLIST Ô ARTIST Ô ALBUM Ô

GENRE Ô TRACK Ô (back to the

beginning)

ALBM RND*

Functions the same as “Shuffle Albums” of the

iPod.

Confirm the selection.

SONG RND/RND ON

Functions the same as “Shuffle Songs” of the iPod

or “Random Play = On” of the D. player.

To move back to the previous menu, press ¢

after pressing MODE.

RND OFF

• If a track is selected, playback starts

automatically.

• If the selected item has another layer, you will

enter the layer. Repeat steps 3 and 4 until the

desired track is played.

Cancels.

* For iPod: Functions only if you select “ALL” in

“ALBUMS” of the main “MENU.”

• Holding 4 /¢ can skip 10 items at

a time.

To check the other information while

listening to an iPod or a D. player

* The menu selecting mode will be canceled:

– If no operations are done for about 5 seconds.

– When you confirm the selection of a track.

Other external component Maintenance

operations

How to clean the connectors

Frequent detachment will deteriorate the connectors.

To minimize this possibility, periodically wipe the

connectors with a cotton swab or cloth moistened with

alcohol, being careful not to damage the connectors.

You can connect an external component to the LINE IN

plugs on the rear, and another to the CD changer jack

on the rear using the Line Input Adapter—KS-U57

(not supplied) or AUX Input Adapter—KS-U58 (not

supplied).

• For connection, see Installation/Connection Manual

(separate volume).

• For listening to the iPod or D. player, refer to pages

17 and 18.

Connector

Moisture condensation

Moisture may condense on the lens inside the unit in

the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.

Should this occur, the unit may malfunction. In this

case, eject the disc and leave the unit turned on for a

few hours until the moisture evaporates.

If “EXT IN” does not appear, see page 16 and

select the external input (“EXT IN”).

Ÿ Turn on the connected component and

start playing the source.

How to handle discs

When removing a disc from its

case, press down the center holder of

the case and lift the disc out, holding

it by the edges.

Center holder

! Adjust the volume.

• Always hold the disc by the edges. Do not touch its

recording surface.

When storing a disc into its case, gently insert the

disc around the center holder (with the printed surface

facing up).

⁄ Adjust the sound as you want. (See

page 14.)

• Make sure to store discs into the cases after use.

To check the other information while

listening to an external component

Clock Ô EXT IN or LINE IN

Continued on the next page

To keep discs clean

More about this unit

A dirty disc may not play correctly.

If a disc does become dirty, wipe it with

a soft cloth in a straight line from center

to edge.

Basic operations

Turning on the power

• Do not use any solvent (for example, conventional

record cleaner, spray, thinner, benzine, etc.) to clean

discs.

• By pressing SRC on the unit, you can also turn on the

power. If the source is ready, playback also starts.

Turning off the power

To play new discs

• If you turn off the power while listening to a disc, disc

play will start from where playback has been stopped

previously, next time you turn on the power.

• For MP3/WMA discs, playback will start from the

beginning of the last playing track.

New discs may have some rough spots

around the inner and outer edges. If

such a disc is used, this unit may reject

the disc.

To remove these rough spots, rub the edges with a

pencil or ball-point pen, etc.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

– Received stations are preset in No. 1 (lowest

frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in No. 1 will

be automatically tuned in.

Do not use the following discs:

Warped disc

Sticker

Sticker residue

• When storing a station manually, the previously

preset station is erased when a new station is stored

in the same preset number.

Stick-on label

Disc operations

Unusual shape

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply

with the “Compact Disc Digital Audio” standard.

Therefore, the use of Non-DVD side of a DualDisc on

this product may not be recommended.

Single CD (8 cm disc)

General

Playing a VCD disc

• This unit has been designed to reproduce CDs/CD

Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable)

in audio CD (CD-DA), MP3 and WMA formats.

• This unit cannot playback SVCD, DVDs, CD-Gs, or CD-I

discs.

• The PBC function is not available for some VCDs.

• The PBC function is automatically canceled when you

change the source or turn off the unit. Playback starts

from the beginning of the dics when you play the

VCD again.

• When a disc is inserted upside down, the disc

automatically ejects.

• While fast-forwarding or reversing on an MP3 or

WMA disc, you can only hear intermittent sounds.

• The On-Screen Display (OSD) will automatically

canceled when you change the source or turn off the

unit.

Playing an MP3/WMA disc

Playing a CD-R or CD-RW

• This unit can play back MP3/WMA files with the

extension code <.mp3> or <.wma> (regardless of

the letter case—upper/lower).

• This unit can show the names of albums, artists

(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or

2.4) for MP3 files.

• This unit can display only one-byte characters. No

other characters can be correctly displayed.

• This unit can play back MP3/WMA files meeting the

conditions below:

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can play back only files of the same type

which are first detected if a disc includes both audio

CD (CD-DA) files and MP3/WMA files.

• This unit can play back multi-session discs; however,

unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this

unit because of their disc characteristics, or for the

following reasons:

– Discs are dirty or scratched.

– Moisture condensation occurs on the lens inside

the unit.

– Bit rate: MP3: 32 kbps — 320 kbps

WMA: 48 kbps — 192 kbps

– Sampling frequency:

– The pickup lens inside the unit is dirty.

– CD-R/CD-RW on which the files are written with

“Packet Write” method.

48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)

24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)

48 kHz, 44.1 kHz, 32 kHz (for WMA)

– There are improper recording conditions (missing

data, etc.) or media conditions (stained, scratched,

warped, etc.).

• CD-RWs may require a longer readout time since the

reflectance of CD-RWs is lower than that of regular

CDs.

• Do not use the following CD-Rs or CD-RWs:

– Discs with stickers, labels, or a protective seal stuck

to the surface.

– Disc format: ISO 9660 Level 1/Level 2, Romeo,

Joliet, Windows long file name

• The maximum number of characters for file/folder

names vary among the disc format used (includes 4

extension characters—<.mp3> or <.wma>).

– ISO 9660 Level 1: up to 12 characters

– ISO 9660 Level 2: up to 31 characters

– Romeo: up to 40 characters

– Joliet: up to 40 characters

– Discs on which labels can be directly printed by an

ink jet printer.

– Windows long file name: up to 40 characters

Using these discs under high temperatures or high

humidities may cause malfunctions or damage to the

unit.

Continued on the next page

• This unit can play back files recorded in VBR (variable

bit rate).

General settings—PSM

• If you change the “AMP GAIN” setting from

“HIGH PWR” to “LOW PWR” while the volume level

is set higher than “VOL 30,” the unit automatically

changes the volume level to “VOL 30.”

Files recorded in VBR have a discrepancy in elapsed

time display, and do not show the actual elapsed

time. Especially, after performing the search function,

this difference becomes noticeable.

• This unit can recognize a total of 512 files, of 200

folders, and of 8 hierarchies.

• This unit cannot play back the following files:

– MP3 files encoded with MP3i and MP3 PRO format.

– MP3 files encoded in an inappropriate format.

– MP3 files encoded with Layer 1.

– WMA files encoded with lossless, professional, and

voice format.

– WMA files which are not based upon Windows

Media® Audio.

– WMA files copy-protected with DRM.

– Files which have the data such as WAVE, ATRAC3,

etc.

iPod or D. player operations

• When you turn on this unit, the iPod or D. player is

charged through this unit.

• While the iPod or D. player is connected, all

operations from the iPod or D. player are disabled.

Perform all operations from this unit.

• The text information may not be displayed correctly.

• If the text information includes more than 8

characters, it scrolls on the display. This unit can

display up to 40 characters.

Notice:

When operating an iPod or a D. player, some

operations may not be performed correctly or as

intended. In this case, visit the following JVC web

site:

For iPod users: <http://www.jvc.co.jp/english/

car/support/ks-pd100/index.html>

For D. player users: <http://www.jvc.co.jp/

english/car/support/ks-pd500/index.html>

• The search function works but search speed is not

constant.

Changing the source

• If you change the source, playback also stops

(without ejecting the disc).

Next time you select “DISC” for the playback source,

disc play starts from where it has been stopped

previously.

• For MP3/WMA discs, playback will start from the

beginning of the last playing track.

• Microsoft and Windows Media are either registered

trademarks or trademarks of Microsoft Corporation in

the United States and/or other countries.

• iPod is a trademark of Apple Inc., registered in the

U.S. and other countries.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds,

the disc is automatically inserted again into the

loading slot to protect it from dust. (Disc will not play

this time.)

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms

Remedies/Causes

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Check the cords and connections.

• The unit does not work at all.

Reset the unit (see page 2).

• SSM automatic presetting does not work. Store stations manually.

• Static noise while listening to the radio.

• Disc automatically ejects.

Connect the antenna firmly.

Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be

skipped.

• Insert a finalized CD-R/CD-RW.

• Finalize the CD-R/CD-RW with the component which you

used for recording.

• Disc can be neither played back nor

ejected.

• Unlock the disc (see page 13).

• Eject the disc forcibly (see page 2).

• Sound and pictures are sometimes

interrupted or distorted.

• Stop playback while driving on rough roads.

• Change the disc.

• Check the cords and connections.

• “NO DISC” appears on the display.

Insert a playable disc into the loading slot.

• No playback picture appears on the

monitor.

Parking brake wire is not connected properly.

(See Installation/Connection manual.)

• No picture appears on the monitor at all. • Connect the video cord correctly.

• Select a correct input on the monitor.

• Disc cannot be played back.

• Use a disc with MP3/WMA tracks recorded in the format

compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file

names.

• Noise is generated.

Skip to another track or change the disc. (Do not add the

extension code <.mp3> or <.wma> to non-MP3 or WMA

tracks.)

• A longer readout time is required (“CHECK” Do not use too many hierarchies and folders.

keeps flashing on the display).

Continued on the next page

Symptoms

Remedies/Causes

• Tracks do not play back in the order you

have intended them to play.

Playback order is determined when the files are recorded.

• Elapsed playing time is not correct.

This sometimes occurs during play. This is caused by how the

tracks are recorded on the disc.

• “NO FILES” appears on the display.

Insert a disc that contains MP3/WMA tracks.

• Correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers, and a

album name).

limited number of symbols.

Insert a disc into the magazine.

Insert the magazine.

• “NO DISC” appears on the display.

• “NO MAG” appears on the display.

• “RESET 8” appears on the display.

Connect this unit and the CD changer correctly and press the

reset button of the CD changer.

• “RESET 1” – “RESET 7” appears on the

display.

Press the reset button of the CD changer.

• The CD changer does not work at all.

Reset the unit (see page 2).

• The iPod or D. player does not turn on or • Check the connecting cable and its connection.

does not work.

• Update the firmware version.

• Charge the battery.

• Buttons do not work as intended.

• The sound is distorted.

The functions of the buttons have been changed. Press MODE

before performing the operation.

Deactivate the equalizer either on the unit or the iPod/

D. player.

• “NO IPOD” or “NO DP” appears on the

display.

• Check the connecting cable and its connection.

• Charge the battery.

• Playback stops.

The headphones are disconnected during playback. Restart

the playback operation using the control panel (see page 17).

• No sound can be heard when

connecting an iPod nano.

• Disconnect the headphones from the iPod nano.

• Update the firmware version of the iPod nano.

• No sound can be heard.

• “ERROR 01” appears on the display

when connecting a D. player.

Disconnect the adapter from the D. player. Then, connect it

again.

• “NO FILES” or “NO TRACK” appears on

the display.

No tracks are stored. Import tracks to the iPod or D. player.

• “RESET 1” – “RESET 7” appears on the

display.

Disconnect the adapter from both the unit and iPod/D. player.

Then, connect it again.

• “RESET 8” appears on the display.

Check the connection between the adapter and this unit.

• The iPod’s or D. player’s controls do not Reset the iPod or D. player.

work after disconnecting from this unit.

Specifications

AUDIO AMPLIFIER SECTION

VCD/CD PLAYER SECTION

Maximum Power Output:

Type:

Compact disc player

Front/Rear:

50 W per channel

Signal Detection

System:

Non-contact optical pickup

(semiconductor laser)

Continuous Power Output (RMS):

Number of Channels: 2 channels (stereo)

Frequency Response: 5 Hz to 20 000 Hz

Front/Rear:

19 W per channel into

4 Ω, 40 Hz to 20 000 Hz at

no more than 0.8% total

harmonic distortion.

Dynamic Range:

96 dB

Signal-to-Noise Ratio: 98 dB

Load Impedance:

Tone Control Range:

Bass:

4 Ω (4 Ω to 8 Ω allowance)

Wow and Flutter:

Less than measurable limit

MP3 Decoding Format: (MPEG1/2 Audio Layer 3)

10 dB at 100 Hz

10 dB at 10 kHz

40 Hz to 20 000 Hz

70 dB

2.5 V/20 kΩ load (full

scale)

Max. Bit Rate:

320 kbps

Treble:

WMA (Windows Media® Audio) Decoding Format:

Frequency Response:

Signal-to-Noise Ratio:

Line-Out Level/

Impedance:

Max. Bit Rate:

192 kbps

GENERAL

Power Requirement:

Output Impedance:

Other Terminal:

1 kΩ

LINE IN, CD changer

Operating Voltage: DC 14.4 V

(11 V to 16 V allowance)

Negative ground

VIDEO SECTION

Grounding System:

Color System:

PAL/NTSC

Allowable Operating 0°C to +40°C

Temperature:

Video Output (Composite): 1 Vp-p/75 Ω

Dimensions (W × H × D): (approx.)

TUNER SECTION

Frequency Range:

Installation Size:

Panel Size:

182 mm × 52 mm × 150 mm

188 mm × 58 mm × 11 mm

FM:

87.5 MHz to 108.0 MHz

Mass:

1.4 kg

(excluding accessories)

AM:

531 kHz to 1 602 kHz

FM Tuner

Usable Sensitivity:

Design and specifications are subject to change without

notice.

11.3 dBf (1.0 μV/75 Ω)

50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)

Alternate Channel

65 dB

Selectivity (400 kHz):

Frequency Response:

Stereo Separation:

AM Tuner

40 Hz to 15 000 Hz

30 dB

Sensitivity/Selectivity:

20 μV/35 dB

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Ada MASALAH dengan cara

pengoperasian?

Setel kembali unit Anda

Lihat halaman mengenai Bagaimana mereset unit anda

EN, IN

0207DTSMDTJEIN

KD-SV3305

Installation/Connection Manual

Manual Pemasangan/Penyambungan

0207DTSMDTJEIN

EN, IN

GET0471-008A

[UN]

ENGLISH

INDONESIA

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does Alat penerima ini didisain untuk beroperasi hanya pada 12 V DC, sistem listrik tanah NEGATIVE. Jika

not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

kendaraan anda tidak memiliki sistem ini, sebuah pembalik tegangan diperlukan, yang mana dapat dibeli

di penyalur-penyalur audio mobil JVC.

WARNINGS

• DO NOT install any unit in locations where;

PERINGATAN

• JANGAN memasang unit pada tempat-tempat dimana;

– it may obstruct the steering wheel and gearshift lever operations.

– it may obstruct the operation of safety devices such as air bags.

– it may obstruct visibility.

– ini dapat menghalangi pengoperasian roda kemudi dan tuas gigi persneling

– ini dapat menghalangi pengoperasian alat pengaman seperti kantung udara.

– ini dapat menghalangi pandangan.

• DO NOT operate the unit while driving.

• JANGAN mengoperasikan unit sewaktu mengemudi.

• If you need to operate the unit while driving, be sure to look ahead carefully.

• The driver must not watch the monitor while driving.

If the parking brake is not engaged, “PARKING” flashes on the display, and no playback

picture will be shown on the monitor.

– This warning appears only when the parking brake wire is connected to the parking brake

system built in the car.

• Jika Anda harus mengoperasikan unit sewaktu mengemudi, pastikan Anda melihat ke depan

dengan hati-hati.

• Pengemudi tidak boleh menonton monitor selagi mengemudi.

Jika rem parkir tidak sedang dipakai, “PARKING” berkedip pada display, dan tidak ada

gambar permainan-ulang yang akan dipertunjukkan pada monitor.

– Peringatan ini muncul hanya jika kabel rem parkir telah tersambung ke sistem rem parkir

yang terpasang tetap di dalam mobil.

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all Untuk mencegah hubungan pendek, kami menyarankan anda memutuskan sambungan terminal negatif

electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

baterai dan membuat semua sambungan-sambungan listrik sebelum memasang alat penerima.

• Pastikan untuk mentanahkan alat penerima ini ke casis mobil kembali setelah pemasangan.

Notes:

Catatan:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio

dealer.

• Ganti sekring dengan voltase yang sudah ditetapkan. Jika sekring sering meledak, konsultasikan pada

penyalur audio mobil JVC anda.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both at

the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than

50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 16 of the

INSTRUCTIONS).

• Disarankan untuk menghubungkan speaker-speaker dengan maksimum power lebih dari 50 W (keduanya

di belakang dan di depan, dengan sebuah impedansi 4 Ω sampai 8 Ω). Jika maksimum power kurang

dari 50 W, ganti pengaturan “AMP GAIN” (“PENAMBAH PENGUAT”) untuk mencegah speaker-speaker

dari kerusakan (lihat halaman 16 dari BUKU PETUNJUK).

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when

removing this unit.

• Untuk mencegah hubungan pendek, tutup ujung-ujung terminal-terminal yang TIDAK DIGUNAKAN

dengan pita isolasi.

• Pendingin menjadi sangat panas setelah digunakan. Hati-hati untuk tidak menyentuhnya ketika

memindahkan alat penerima ini.

Heat sink

Pendingin

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit

will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

TINDAKAN-TINDAKAN PENCEGAHAN pada suplai power dan

sambungan-sambungan speaker:

• JANGAN sambungkan ujung-ujung speaker dari kabel power ke baterai mobil; sebaliknya,

alat penerima tersebut akan secara serius rusak.

• SEBELUM menyambung ujung-ujung speaker dari kabel power ke speaker-speaker, cek perkabelan

speaker dalam mobil anda.

Parts list for installation and connection

Daftar bagian-bagian untuk pemasangan dan penyambungan

If any item is missing, consult your JVC car audio dealer immediately.

Jika ada item yang hilang, segera hubungi dealer audio mobil JVC anda.

A / B

Hard case/Control panel

Kotak keras/Panel kontrol

Sleeve

Selongsong

Trim plate

Plat rapi

Power cord

Kabel power

Crimp connector

Konektor kerut

Washer (ø5)

Perapat sambungan (ø5)

Lock nut (M5)

Mur kunci (M5)

Mounting bolt (M5 × 20 mm)

Baut bingkai (M5 × 20 mm)

Rubber cushion

Bantalan karet

Handles

Pegangan-pegangan

Remote controller

Remote kontrol

Battery

Baterai

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information

regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

PEMASANGAN (BINGKAI-DALAM DASH)

Ilustrasi berikut menunjukkan sebuah tipe pemasangan. Jika anda mempunyai suatu pertanyaan atau

informasi yang diperlukan mengenai alat-alat pemasangan, konsultasikan pada penyalur audio mobil JVC

atau sebuah perusahaan yang mensuplai alat-alat.

• Jika anda tidak yakin bagaimana memasang alat penerima ini dengan benar, biarkan dipasang dengan

teknisi yang berkualitas.

Do the required electrical connections.

Lakukan penyambungan-penyambungan

listrik yang diperlukan.

Bend the appropriate tabs to hold the

sleeve firmly in place.

Bengkokkan pengait-pengait yang

tepat untuk menahan selongsong

secara kuat pada tempatnya.

When using the optional stay

penguat tambahan

Ketika menggunakan

When installing the unit without using the sleeve / Ketika memasang alat penerima

tanpa menggunakan selongsong

Stay (option)

Penguat (tambahan)

In a Toyota car for example, first remove the car radio and install the unit in its place.

Dalam sebuah kereta Toyota misalnya, pertama pindahkan radio mobil dan pasang alat penerima tersebut ke dalam tempatnya.

Fire wall

Dinding tahan api

Flat type screws (M5 × 8 mm)*²

Sekrup-sekrup tipe rata (M5 × 8 mm)*²

Dashboard

Tempat alat pada bagian

depan

Bracket*²

Breket*²

Screw (option)

Sekrup (tambahan)

Flat type screws (M5 × 8 mm)*²

Sekrup-sekrup tipe rata (M5 × 8 mm)*²

Pocket

Kantong

Bracket*²

Breket*²

Note

: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws

are used, they could damage the unit.

: Ketika memasang alat penerima pada breket bingkai, pastikan untuk menggunakan sekrup-sekrup panjang–

8 mm. Jika sekrup yang lebih panjang digunakan, maka dapat merusak alat penerima.

Install the unit at an angle of less than 30˚.

Pasang penerima pada suatu sudut kurang

dari 30˚.

Catatan

Removing the unit

Memindahkan alat penerima

Before removing the unit, release the rear section.

Sebelum memindahkan alat penerima, lepaskan seksi belakang.

Insert the two handles, then pull them as

illustrated so that the unit can be removed.

Sisipkan kedua pemegang dan tarik alat penerima

seperti yang diilustrasikan hingga alat penerima

dapat dipindahkan.

When you stand the unit, be careful not to damage the fuse on the rear.

Not supplied for this unit.

Ketika anda memberdirikan alat penerima, hati-hati untuk tidak merusak sekring di belakang.

Tidak disediakan untuk alat penerima ini.

PEMECAHAN MASALAH

TROUBLESHOOTING

• Sekring meledak.

• The fuse blows.

* Apakah ujung-ujung merah dan hitam tersambung dengan benar?

* Are the red and black leads connected correctly?

• Power tidak dapat dihidupkan.

• Power cannot be turned on.

* Apakah ujung kuning sudah tersambung?

* Is the yellow lead connected?

• Tidak ada suara dari speaker.

• No sound from the speakers.

* Apakah ujung keluaran speaker terhubung pendek?

* Is the speaker output lead short-circuited?

• Suara terdistorsi.

• Sound is distorted.

* Apakah ujung keluaran speaker sudah ditanahkan?

* Apakah terminal-terminal “–” dari speaker-speaker L dan R sudah ditanahkan secara umum?

* Is the speaker output lead grounded?

* Are the “–” terminals of L and R speakers grounded in common?

• Berisik yang mengganggu suara-suara.

• Noise interfere with sounds.

* Apakah terminal tanahan belakang tersambung ke casis mobil menggunakan kabel-kabel terpendek dan

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

tertebal?

• This unit becomes hot.

• Alat penerima menjadi panas.

* Is the speaker output lead grounded?

* Apakah ujung keluaran speaker sudah ditanahkan?

* Are the “–” terminals of L and R speakers grounded in common?

* Apakah terminal-terminal “–” dari speaker-speaker L dan R sudah ditanahkan secara umum?

• This unit does not work at all.

• Alat penerima ini tidak bekerja secara keseluruhan.

* Have you reset your unit?

* Apakah anda sudah reset (memasang kembali) alat penerima anda?

ENGLISH

INDONESIA

ELECTRICAL CONNECTIONS

SAMBUNGAN-SAMBUNGAN LISTRIK

Typical connections / Ciri khas sambungan-sambungan

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious

damage to this unit.

The leads of the power cord and those of the connector from the car body may be different in color.

Sebelum penyambungan: Cek perkabelan dalam mobil dengan hati-hati. Penyambungan yang

tidak benar mungkin menyebabkan kerusakan serius pada alat penerima.

Ujung dari kabel power dan beberapa konektor dari bodi mobil mungkin berbeda dalam warna.

1 Connect the colored leads of the power cord in the order specified in the illustration below.

2 Connect the antenna cord.

1 Sambungkan ujung berwarna dari kabel power dalam urutan spesifikasi pada ilustrasi di bawah.

2 Sambungkan kabel antena.

3 Finally connect the wiring harness to the unit.

3 Akhirnya sambungkan dudukan kabel ke alat penerima.

LINE IN

(see diagram / lihat diagram

)

Line out (see diagram

Keluaran (lihat diagram

)

VIDEO OUT

(see diagram / lihat diagram

)

Rear ground terminal

Terminal tanah belakang

15 A fuse

Sekring 15 A

Antenna terminal

Terminal antena

To external components

(see diagram

)

Ke komponen eksternal

(lihat diagram

)

Ignition switch

Saklar kontak

Black

Hitam

To metallic body or chassis of the car

Ke besi bodi atau casis dari mobil tersebut

Yellow*²

To a live terminal in the fuse block connecting to the car battery

(bypassing the ignition switch) (constant 12 V)

Kuning*²

Ke sebuah tempat terminal dalam blok sekring disambungkan ke

baterai mobil (abaikan saklar kontak) (konstant 12 V)

Red

Merah

To an accessory terminal in the fuse block

Ke sebuah terminal aksesoris dalam blok sekring

Fuse block

Blue

Biru

Blok sekring

To the automatic antenna if any (250 mA max.)

Ke antena otomatis jika ada (maksimum 250 mA)

Blue with white stripe

Biru dengan strip putih

To the remote lead of other equipment (200 mA max.)

Ke ujung jauh dari peralatan lain (maksimum 200 mA)

Brown

Coklat

To cellular phone system

Untuk sistem telepon selular

Light green

Hijau muda

To parking brake, metallic body or chassis of the car

Ke rem parkir, logam body atau casis mobil.

White with black stripe

Putih dengan strip hitam

White

Putih

Gray with black stripe

Abu-abu dengan strip hitam

Gray

Abu-abu

Green with black stripe

Hijau dengan strip hitam

Green

Hijau

Purple with black stripe

Ungu dengan strip hitam

Purple

Ungu

Left speaker (front)

Speaker kiri (depan)

Right speaker (front)

Speaker kanan (depan)

Left speaker (rear)

Speaker kiri (belakang)

Right speaker (rear)

Speaker kanan (belakang)

Connecting the parking brake wire / Menyambung kabel rem parkir

When installing the monitor in a location where it can be seen by the driver

Connect the parking brake wire to the parking brake system built in the car.

Ketika memasang monitor pada tempat yang dapat dilihat oleh pengemudi

Sambungkan kabel rem parkir ke sistem rem parkir yang terpasang tetap dalam mobil.

When installing the monitor in a location where it cannot be

seen by the driver

Connect the parking brake wire to metallic body or chassis of the

car.

Ketika memasang monitor pada tempat yang tidak dapat

dilihat oleh pengemudi

Sambungkan kabel rem parkir ke logam body atau casis mobil.

Parking brake wire (light green)

Kabel rem parkir (hijau muda)

Parking brake

Rem parkir

Parking brake wire (light green)

Kabel rem parkir (hijau muda)

To metallic body or chassis of the car

Ke logam body atau casis mobil

Parking brake switch (inside the car)

Saklar rem parkir (di dalam mobil)

Connecting the crimp connector / Menyambung konektor kerut

Wire connecting the battery and the parking brake switch.

Contact the metallic part of the crimp to the wires inside.

Hubungkan bagian logam dari konektor kerut ke kabel-

kabel di dalam.

Kabel yang menyambungkan baterai dan saklar rem parkir.

Pinch the crimp firmly.

Jepit konektor dengan kuat.

Attach the parking brake wire to this point.

Pasal kabel rem parkir ke poin ini.

Not supplied for this unit.

Tidak disediakan untuk alat penerima ini.

Sebelum pengecekan pengoperasian dari alat penerima ini sebelum pemasangan, ujung ini harus sudah

dihubungkan, selain itu power tidak dapat dihidupkan.

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power

cannot be turned on.

Connecting the monitor / Menyambung monitor

Video cord*³

Kabel video*³

or / atau

Rear side

Sisi belakang

KV-MR9010

9-INCH WIDESCREEN MONITOR*³

MONITOR LAYAR LEBAR 9 INCI*³

Connecting the external amplifier / Penyambungan penguat eksternal

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it

can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker

leads of this unit unused.

Anda dapat menyambungkan penguat untuk meningkatkan sistem stereo mobil anda.

• Sambungkan ujung jauh (biru dengan strip putih) ke ujung jauh dari peralatan lain sehingga dapat

dikontrol melalui alat penerima ini.

• Putuskan sambungan speaker-speaker dari alat penerima ini, sambungkan ini ke penguat.

Biarkan ujung speaker dari alat penerima ini tidak digunakan.

Y-connector*³

Remote lead

Ujung jauh

Konektor Y*³

Remote lead (blue with white stripe)

Ujung jauh (biru dengan strip putih)

Rear speakers

Speaker-speaker belakang

To the remote lead of other equipment or

automatic antenna if any

Ke ujung jauh dari peralatan lain atau antena

otomatis jika ada

JVC Amplifier

Penguat JVC

Front speakers

Speaker-speaker depan

Connecting the external components / Menyambung komponen eksternal

JVC CD changer, Apple iPod, or JVC D. player / JVC CD changer, Apple iPod atau JVC D. player

• Set “CHANGER” for the external input setting (See page 16 of the INSTRUCTIONS.) / Aturlah “CHANGER” untuk pengaturan input eksternal (Lihat halaman 16 dari BUKU PETUNJUK.

)

You can connect these components as illustrated below. The iPod or D. player can be connected using

an interface adapter (not supplied)—KS-PD100 (for iPod) or KS-PD500 (for D. player).

Anda bisa menyambungkan komponen-komponen ini seperti yang diilustrasikan di bawah. iPod atau

D. player bisa disambungkan dengan mengunakan adaptor antarmuka (tidak disediakan)—KS-PD100

(untuk iPod) atau KS-PD500 (untuk D. player).

CAUTION

PERINGATAN:

Before connecting the external components, make sure that the unit is turned off.

Sebelum menyambungkan komponen eksternal, pastikan bahwa alat penerima sudah dimatikan.

JVC CD changer

CD changer JVC

CD changer jack

Konektor CD changer

or / atau

Apple iPod

or / atau

iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

iPod adalah merek dagang dari Apple Computer, Inc., terdaftar di Amerika Serikat dan di

negara-negara lain.

JVC D. player

Other external component / Komponen eksternal lainnya

• Set “EXT IN” for the external input setting (See page 16 of the INSTRUCTIONS.) / Aturlah “EXT IN” untuk pengaturan

input eksternal (Lihat halaman 16 dari BUKU PETUNJUK.)

External component

Komponen eksternal

External component

Komponen eksternal

CD changer jack

Konektor CD changer

3.5 mm stereo mini plug

Steker mini stereo 3.5 mm

atau

External component

Komponen eksternal

Not supplied for this unit.

Signal cord (not supplied for this unit).

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint

(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the

unit.

Connecting cord supplied for your CD changer.

Line Input Adapter KS-U57 (not supplied for this unit).

AUX Input Adapter KS-U58 (not supplied for this unit).

Tidak disediakan untuk alat penerima ini.

Kabel sinyal (tidak disediakan untuk alat penerima ini).

Pasangkan dengan kuat kabel tanah ke bodi besi atau ke casis dari mobil—pada tempat yang tidak dilapisi cat

(jika dilapisi cat, hilangkan cat sebelum memasang kabel). Kegagalan melakukan ini mungkin menyebabkan

kerusakan pada alat penerima tersebut.

Penyambung sinyal disediakan untuk CD changer anda.

Adapter Jalur Masukan KS-U57 (tidak disediakan untuk alat penerima ini).

Adapter Masukan AUX KS-U58 (tidak disediakan untuk alat penerima ini).

AMX Wall Docking Station MVP WDS User Manual
Canon HFR16 User Manual
Canon XL1SA User Manual
Cleveland Range GFB 60 User Manual
Dual XPE1700 User Manual
Elation Professional Camcorder EVC MH User Manual
GE PROFILE ADVANTIUM SCB2001K User Manual
Honeywell HMLCD15 User Manual
JBL GTO75 2 User Manual
JVC Everio Camera GZ MS110BUS User Manual