JVC CS WDS1 User Manual

Accessories  
A Hexagonal head tapping screw  
B Hexagonal head tapping screw  
C Protection bar x 4  
CAR STEREO SPEAKER  
x 16 (R4 x 30 mm)  
x 8 (R4 x 20 mm)  
CS-WDS1  
Use a M4 hex wrench.  
D Paper pattern  
For Tweeter  
For Woofer  
How to use the paper pattern  
1. Cut out the paper pattern along the perforation.  
2. Place and trace the paper pattern over the mounting  
area on the vehicle or board.  
3. Cut out the mounting area on the vehicle or board along  
the marking.  
Specifications  
The diaphragm of this speaker makes use of birch wood to faithfully reproduce the original sound.  
Each unit, therefore, has a unique appearance.  
Type  
: 2-Way Separate Speaker  
Thiele/ Small Parameter  
(14.5 cm Woofer)  
Thank you for purchasing the JVC Car Stereo Speakers. For the secure installation and perfect operation of your  
speaker, please read the following instructions carefully.  
Frequency Response : 45 Hz - 50 kHz  
Sound Pressure Level : 84 dB/W0m  
Recommended Crossover Frequency  
Revc (DC VC Res ) 3.4  
Ohms  
Ohms  
Hz  
: 4.5 kHz (Cut-off Slope:-12 dB/oct.)  
Imp. (300Hz)  
4
Mounting the speaker  
14.5cm Wood Cone Woofer  
Power Handling Capacity (Nominal)  
: 50 W  
Power Handling Capacity (Max. Music Power)  
: 150 W  
Impedance  
Frequency Response : 45 Hz - 8 kHz  
Sound Pressure Level : 84 dB/W0m  
Fo (Res Freq )  
Zo (Zmax at Fo)  
Sd (Piston Area)  
BL (Flux*Length)  
Qms (Mech Q)  
Qes (Elec Q)  
80.2  
Professional knowledge is required for mounting this speaker. For details, please consult the authorized dealer.  
Make use of the paper pattern provided when processing the mounting board of the speaker.  
During mounting, ensure that there is enough spacing to avoid hitting against any parts such as window glass.  
In order to optimize the sound field of the wood cone, it is recommended that the speaker terminal be mounted at the  
bottom with the wood grain in the vertical direction.  
26.9  
Ohm  
sqM  
TM  
0.0095  
6.08  
: 4 K  
3.814  
0.667  
0.568  
4.13  
Notes for dealers  
Mass  
: 1.5 kg (one piece)  
Upon completing the mounting, please hand this instruction manual to the customer.  
Qts (Total Q)  
2cm Wood Dome Tweeter  
Power Handling Capacity (Nominal)  
Vas (Acous Vol)  
Le (Inductance)  
Cms (Compliance)  
Mms (Total Mass)  
Litr  
For Proper Installation and Use  
0.286  
321.9  
12.23  
mH  
: 50 W (4.5 KHz -12 db/oct. H.P.F.)  
Power Handling Capacity (Max. Music Power)  
: 150 W (4.5 KHz -12 db/oct. H.P.F.)  
: 4 K  
uM/N  
Gram  
Gram  
1. Be sure to install the speakers according to the directions so as to prevent them from slipping accidentally out of position due to the  
repeated impact of opening and closing doors or the tossing and bumping of the vehicle.  
2. Set the wiring firmly on the floor of the vehicle, taking the utmost care not to break wires while installing. When installing the speakers  
in the doors, extra attention must be paid to allowing reasonable play to the wires. The wiring, if given too much clip or clamp, will get  
pinched in between the door and body of the vehicle when opening and closing doors.  
3. Since the speaker installed in the door is positioned at the foot level, be careful not to damage the speaker by giving it an inadvertent  
kick. Check the water outlet at the bottom of the door occasionally to ensure that it drains well, leaving no rainwater inside the door.  
4. Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the  
connection if the power is on may damage the speakers.  
Impedance  
Mmd (DiaphmMass) 11.70  
Frequency Response : 3 kHz - 50 kHz  
Sound Pressure Level : 84 dB/W0m  
Mass  
: 235 g (one piece)  
Designs and specifications are subject to change without notice.  
5. The amplifier and speakers should be connected between corresponding terminals, i.e. “left” to “left”, and “right” to “right”, as well as  
“+” to “+”, and “–” to “–”. Connection with reversed polarity will degrade the quality of stereo reproduction.  
6. Do not subject the speakers to excessive input. Any excessive input may damage the speakers.  
7. Make sure that the output impedance of the amplifier’s speaker terminal is rated at 4 ohms.  
8. Please use a high-pass filter.  
(Cut-off Frequency is 4.5 kHz and above -12dB/oct)  
9. When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.  
INSTRUCTIONS  
LVT1405-002A  
[E]  
EN  
2006 Victor Company of Japan, Limited  
0606SKMSANTCN  

Acer A231H User Manual
Aluratek CINECAM AHDVC01F User Manual
Black Decker BX180 User Manual
Bryan Boilers LDTV 15 User Manual
Burnham Independence IN7 User Manual
Canon MVX30i User Manual
Carson Manufacturing Company, Inc Car Speaker 1022 10 14 V User Manual
Carson Optical Binoculars User Manual
Eclipse Fujitsu Ten Car Stereo System CD8455 User Manual
Eizo Nanao Car Video System CE240W User Manual