JL Audio Stealthbox 94376 User Manual

SB-F-EDG/10W3v3 INSTR_SKU# 011254  
InstallatIon  
d I F F I C u lt Y :  
If you choose to perform the installation yourself, it is absolutely vital that  
the Stealthbox® be properly mounted to the vehicle according to these  
instructions. Failure to mount the enclosure properly presents two problems:  
out  
oF  
I n s t a l l a t I o n G u I d e  
for the  
1) The sub-bass performance will suffer due to the movement of the enclosure  
caused by the force exerted by the woofer(s).  
35  
SB-F-Edg/10W3v3  
sKu#94376  
2) A loose enclosure presents a serious safety hazard in the event of a collision  
or sudden deceleration.  
estImated tIme:  
2-3 HouRs  
2007+ Ford edge  
s t e P  
1
Remove the floor panel by lifting seat flaps. Carefully tilt  
entire panel to exit hatch diagonally.  
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper  
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.  
s t e P  
2
Remove threshold plate by lifting directly upward.  
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio  
dealer. The installation professionals employed by your dealer have the necessary tools and experience  
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage  
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you  
prefer to perform your own installation, please read this installation guide completely  
before beginning the process.  
s t e P  
3
Remove foam filler panel from passenger side of spare tire.  
Continued on Next Page  
SB-F-EDG/10W3v3_INSTR_SKU# 011254  
s t e P 1 2  
S T E P 1 6  
Remove backing from wax square and place it on sheet  
metal just below tail light wiring as shown.  
Put Stealthbox® into final position with mounting stud  
extended through hole drilled in tail light area. Secure with  
nut, lock washer, and flat washer provided (see illustration).  
s t e P 1 3  
S T E P 1 7  
STEALTHBOX WALL  
Place Stealthbox® into location as shown, push stud against  
wax square to make an impression in the wax square.  
VEHICLE SHEET METAL  
LOCK WASHER  
Position the Stealthbox® into the mounting location. From  
the outside of the vehicle (behind the taillight) place the sup-  
plied fender washer, flat washer, lock washer and then nut  
onto the exposed socket cup set screw. Use a long 3/8" open  
end wrench or ratcheting box end to secure the mounting  
hardware. Be sure Stealthbox is now solidly mounted to  
vehicle.  
HEX NUT  
SOCKET CUP SET SCREW  
FLAT WASHER  
THREADED INSERT  
FENDER WASHER  
Note: For added weather protection, it is recommended  
that you apply a bead of silicone between the vehicle  
and the fender washer.  
s t e P 1 4  
S T E P 1 8  
Connect the previously run wire to the Stealthbox® and test  
the system to ensure that everything sounds good so far.  
Remove Stealthbox®. Drill 1/2 inch diameter hole through  
wax square and sheet metal at stud impression.  
Remove the wax square.  
it is recommended that vehicle undercoating be applied  
where the mounting hole was drilled.  
s t e P 1 5  
Extend mounting stud 1 1/2 inch from enclosure.  
S T E P 1 9  
Reinstall taillight in reverse oder of removal as detailed in  
steps 9,8. Make sure that bulbs go into the right locations  
in the lens assembly by checking the brake lights, running  
lights and, reverse lights. Be carefull of alignment of pins as  
lens assembly is reinserted into fender recess. Secure mount-  
ing with the factory 8mm screws.  
Page 3 • JL Audio, Inc 2008  
Continued on Next Page  
SB-F-EDG/10W3v3_INSTR_SKU# 011254  
s t e P 2 0  
S T E P 2 4  
Drill 1/8 inch holes as indicated on template.  
Place cargo side panel onto a flat surface with back side up.  
Locate back side of storage compartment. Carefully grind  
heads of plastic spot welds to allow removal of compartment  
enclosure. Take care not to damage front of panel.  
s t e P 2 1  
Remove storage compartment from side panel.  
S T E P 2 5  
Install grille with short #8 screws and #8 flat washers as  
provided.  
s t e P 2 2  
S T E P 2 6  
Using provided grill as a guide, mark the required grill open-  
ing onto the side cargo panel with grease pencil or masking  
tape. Cut out opening to allow fitment of grill with maximum  
open area.  
Step backwards through steps 7- 1, installing side cargo  
panel, side threshold plate, rear seat belt bolt, rear threshold  
plate and floor as removed.  
C o n G R a t u l a t I o n s !  
You have completed the installation for this model!  
Enjoy your new Stealthbox®!  
Please refer to the Power Recommendation section for an  
amplifier recommendation and basic set-up help.  
s t e P 2 3  
Position provided grille template on front of side of cargo  
panel so as to cover storage pocket opening and, align with  
horizontal ridges below. Tape into place.  
Page 4 • JL Audio, Inc 2008  
Continued on Next Page  
SB-F-EDG/10W3v3_INSTR_SKU# 011254  
I n C l u d e d H a R d W a R e  
(1) wax square  
(8) #8x 3/8” Pan head phillips screws  
(8) #8 SAE Flat Washer  
(1) 3/8-16 X 2.25 set screw stud  
(1) 3/8 X 2 fender washer  
(1) 3/8 lock washer  
(1) 3/8 X 1.25 nut  
(1) grill panel template  
s P e C I F I C a t I o n s  
Enclosure Type: Acoustic Suspension (sealed)  
Driver Type: 10W3v3-4  
Nominal Impedance: 4 ohms mono  
Continuous Power Handling: 500 Watts  
P o W e R R e C o m m e n d a t I o n  
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.  
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2  
when being used to power your Stealthbox®.  
The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more  
detailed information about installing and tuning this amplifier.  
m I d / H I G H F R e q u e n C Y d R I v e R F I t m e n t  
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.  
Front Speaker Size / Location: 5”x 7” / 6”x 8”- Front Doors  
Fits JL Audio Models: TR570-CXi, C5-570, C5-570x & ZR570-CSi  
Rear Speaker Size / Location: 5”x 7” / 6”x 8”- Rear Door  
Fits JL Audio Models: TR570-CXi, C5-570x  
(954) 443-1100  
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered  
trademarks of JL Audio, Inc. “Ahead of the Curveand its respective logo is a trademark of JL Audio, Inc.  
JLA-SKU# 011254 3-19-2008  
Printed in USA  
©2007 JL Audio, Inc.  
U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479  
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.  
For more detailed information please visit us online at www.jlaudio.com.  
1
0
3
6
9
N
O
R
T
H
C
O
M
M
E
R
C
E
P
A
R
K
W
A
Y
M
I
R
A
M
A
R
,
F
L
O
R
I
D
A
3
3
0
2
5
U
S
A
Page 5• JL Audio, Inc 2008  

Aiwa CT ZI09 User Manual
Ariston Boiler 32 MFFI User Manual
Black Decker BL10451GNEWUC User Manual
Canon Camcorder HF G30 User Manual
Canon Speedlite Flash 5296B002 User Manual
Canon ZR60 User Manual
Clarion DPX1800 User Manual
Dualit Kitchen Blender User Manual
Hypertec PerfectSkin 15 4 N19588NHY User Manual
JVC CU V615U User Manual