JL AUDIO e6450
six-channel full-range amplifier
o w n e r ’ s m a n u a l
Thank you for purchasing a JL Audio amplifier for
your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your
vehicle. For maximum performance and extended warranty
coverage, we highly recommend that you have your new amplifier
installed by an authorized JL Audio dealer. Your authorized
dealer has the training, expertise and installation equipment to
ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact
your authorized JL Audio dealer for assistance. If you need further
assistance, please call the JL Audio Technical Support Department at
(954) 443-1100 during business hours (Eastern Time Zone).
PRODUCT DESCRIPTION
FUSE REQUIREMENTS
The JL Audio e6450 is a six-channel full-range
amplifier utilizing patented Absolute Symmetry™
Class AB technology for all channels.
The e6450 can be operated with a wide variety
of source units and system configurations.
7) Securely mount the amplifier using the
supplied screws.
8) Connect the positive and negative power
wires to the amplifier.A fuse near the amplifier is
not necessary.
The e6450's “+12VDC” and “Ground”
connections are designed to accept 4 AWG
power wire. 4 AWG is a minimum power
wire size for this amplifier.
If you are installing the e6450 with other
amplifiers and wish to use a single main power
wire, use 2 AWG or 1/0 AWG main power wire
(depending on the overall current demands of all
the amplifiers in the system).This 2 AWG or
1/0 AWG power wire should terminate into a
distribution block mounted as close to the
amplifiers as possible and should connect to the
e6450 with 4 AWGpower wire.
Please note that smaller AWG numbers mean
bigger wire and vice-versa (1/0 AWG is the
largest, 2 AWG is smaller, then 4 AWG, then
8 AWG, etc.).
To connect the power wires to the amplifier,
first back out the set screw on the top of the
terminal block, using the supplied 2.5 mm hex
wrench. Strip 1/2 inch (12 mm) of insulation from
the end of each wire and insert the bare wire
into the terminal block, seating it firmly so that no
bare wire is exposed.While holding the wire in
place, tighten the set screw firmly, taking care not
to strip the head of the screw.
The ground connection should be made using
the same gauge wire as the power connection
and should be kept as short as possible, while
accessing a solid piece of sheet metal in the vehicle.
The surface of the sheet metal should be sanded at
the contact point to create a clean, metal-to-metal
connection between the chassis and the termination
of the ground wire.The use of a star washer to lock
down the connection is advisable.
Any wires run through metal barriers (such as
firewalls), must be protected with a high quality
rubber grommet to prevent damage to the
insulation of the wire. Failure to do so may result in
a dangerous short circuit.
It is absolutely vital that the main power wire(s)
to the amplifier(s) in the system be fused within
18 inches (45 cm) of the positive battery post
connection.The fuse value at each power wire
should be high enough for all of the equipment
being run from that power wire. If only the
e6450 is being run from that power wire, we
recommend a 60A fuse be used. AGU (big glass
fuse) or MaxiFuse™ (big plastic-body fuse) types
are recommended.
9) Connect the remote turn-on wire
to the amplifier.
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence for a
typical amplifier installation, using an aftermarket
source unit. Additional steps and different
procedures may be required in some applications. If
you have any questions, please contact your
authorized JLAudio dealer for assistance.
10) Connect the input cables to the amplifier.
11) Connect the speaker wires to the amplifier.
12) Carefully review the amplifier’s control
settings to make sure that they are set according to
the needs of the system.
13) Install the power wire fuse (60A for a
single e6450) and reconnect the negative
battery post terminal.
14) Turn on the source unit at a low level
to double-check that the amplifier is configured
correctly. Resist the temptation to crank it up until
you have verified the control settings.
15) Make necessary adjustments to the input
sensitivity controls to obtain the right overall output
and the desired balance in the system. See
Appendix A (page 12) for the recommended input
sensitivity setting method.
No fuse is required or recommended directly
before the amplifier power connection. If one is
desired, we recommend the use of a 60A AGU fuse
or MaxiFuse™ type.
1) Disconnect the negative battery post
connection and secure the disconnected cable to
prevent accidental re-connection during installation.
This step is not optional!
2) Run power wire (minimum 4 AWG) from
the battery location to the amplifier mounting
location, taking care to route it in such a way that
it will not be damaged and will not interfere
with vehicle operation. Use 2 AWG or 1/0 AWG
power wire if additional amplifiers are being
installed with the e6450.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse block
(and connectors) within 18 inches (45 cm) wire
length of the positive battery post. This fuse is
essential to protect the vehicle. Do not install the
fuse until the power wire has been connected to
the amplifier.
4) Run signal cables and remote turn-on wire
from the source unit to the amplifier
mounting location.
5) Run speaker wire from the speaker systems to
the amplifier mounting location.
6) Find a good, solid metal grounding point close
to the amplifier and connect the negative power
wire to it using appropriate hardware. Use the same
size power wire as the wire connected to the
“+12V” connection (minimum 4 AWG), no longer
than 36 inches (90 cm) from the amplifier to the
ground connection point. In some vehicles, it may be
necessary to upgrade the battery ground wire.
(See page 5 for important notice).
TURN-ON LEAD
The e6450 uses a conventional +12V remote
turn-on lead, typically controlled by the source unit's
remote turn-on output.The amplifier will turn on
when +12V is present at its “Remote” input and
turn off when +12V is switched off. If a source unit
does not have a dedicated remote turn-on output,
the amplifier’s turn-on lead can be connected to
+12V via a switch that derives power from an
ignition-switched circuit.
The e6450's “Remote” turn-on connector is
designed to accept 18 AWG – 12 AWG wire.To
connect the remote turn-on wire to the amplifier,
first back out the set screw on the top of the
terminal block, using the supplied 2.5mm hex
wrench. Strip 1/2 inch (12mm) of wire and insert
the bare wire into the terminal block, seating it
firmly so that no bare wire is exposed.While
holding the wire in the terminal, tighten the set
screw firmly, taking care not to strip the head of the
screw and making sure that the wire is firmly
gripped by the set screw.
16) Enjoy the fruits of your labor with your
favorite music.
POWER CONNECTIONS
Before installing the amplifier, disconnect the
negative (ground) wire from the vehicle's battery.
This will prevent accidental damage to the system,
the vehicle and your body during installation.
IMPORTANT
!
Many vehicles employ small (10 AWG - 6 AWG)
wire to ground the battery to the vehicle chassis and
to connect the alternator's positive connection to the
battery.To prevent voltage drops, these wires should
be upgraded to 4 AWG when installing amplifier
systems with main fuse ratings above 60A.
4
JL AUDIO e6450
JL AUDIO e6450
5
INPUT SECTION
AMPLIFIER CONTROLS
The e6450’s input section allows you to send
signal to the amplifier section through the use of
two, four or six inputs and offers two distinct input
connection options.These are:
1)Three pairs of traditional RCA type
connections designed to accept input from source
units with line level outputs.
2) An eight-pin connector designed to accept
input from amplified sources such as factory source
units or source units not equipped with line level
outputs. Channels 5 & 6 of the e6450 do not have
discrete inputs on this connector. However, signal
from channels 1 & 2 and channels 3 & 4 can be
summed and sent to channels 5 & 6 when “SUM” is
selected with the “Input Mode” switch in the
Channel 5 & 6 Controls section.
y-adaptors and feed these signals into the inputs to
channels 1, 2, 3 & 4.The dedicated subwoofer signal
should be sent to channels 5 & 6.
If you wish to use only two channels of input to
deliver signal to all six amplifier channels, it will be
necessary to split the two signals with y-adaptors
and feed these signals into the inputs to channels
1, 2, 3 & 4. Set the “Input Mode” switch in the
“Channel 5 & 6 Controls” section to “SUM” and
use only the inputs to channels 1, 2, 3 & 4.
The same input connection option does not
need to be used for each channel pair.The “Input
Sens.” adjustment is independent for each channel
pair and must be adjusted based on input level and
the impedance of the load on that pair of channels.
Specific “Input Sens.” adjustment information is
given in Appendix A (page 12).
Input Sensitivity
These controls, labeled “Input Sens.”,can be
used to match the source unit's output voltage(s)
to each input stage of the e6450 for maximum
clean output. Rotating an “Input Sens.” control
clockwise will result in higher sensitivity (louder for
a given input voltage). Rotating an “Input Sens.”
control counter-clockwise will result in lower
sensitivity (quieter for a given input voltage.)
To properly set the amplifier for maximum clean
output, please refer to Appendix A (page 12) in this
manual.After using this procedure, you can then
adjust any or all “Input Sens.” levels downward if this
is required to achieve the desired system balance.
Do not increase any “Input Sens.” setting for
any channel(s) of any amplifier in the system
beyond the maximum level established during the
procedure outlined in Appendix A (page 12).
Doing so will result in audible distortion and
possible speaker damage.
1) “Filter Mode” Control:The e6450 employs a
12dB per octave filter for each pair of channels (one
filter for channels 1&2, another filter for channels
3&4 and another filter for channels 5&6). Each of
these filters can be configured independently into
one of two filter types or defeated completely by
way of the three-position “Filter Mode” switches:
“Off”: Defeats the filter completely, allowing the full
range of frequencies present at the inputs to feed
the amplifier.This is useful for systems utilizing
outboard crossovers or requiring full-range
reproduction from one, two or all of the e6450’s
channel pairs.
“LP” (Low-Pass): Configures the filter to attenuate
frequencies above the selected filter frequency at a
rate of 12dB per octave.This is useful for
connection of subwoofer(s) to one, two or all of
the e6450’s channel pairs in a bi-amplified system.
“HP” (High-Pass): Configures the filter to attenuate
frequencies below the selected filter frequency at a
rate of 12dB per octave.This is useful for
Filter Controls
Most speakers are not designed to reproduce
the full range of frequencies audible by the human
ear. For this reason, most speaker systems are
comprised of multiple speakers, each dedicated to
reproducing a specific frequency range. Filters are
used to select which frequency range is sent to
each section of a speaker system.The division of
frequency ranges to different speakers can be
done with passive filters (coils and/or capacitors
between the amplifier outputs and the speakers),
which are acceptable and commonly used for
filtering between mids and tweeters. Filtering
between subwoofer systems and satellite speaker
systems is best done with active filters, which cut
off frequency content at the input to the amplifier.
Active filters are more stable than passive filters
and do not introduce extraneous resistance,
which can degrade subwoofer performance.
The active filter built into each channel of the
e6450 can be used to eliminate potentially harmful
and/or undesired frequencies from making their way
through the amplifier sections to the speaker(s).This
serves to improve tonal balance and to avoid
distortion and possible speaker failure. Correct use
of these filters can substantially increase the
longevity and fidelity of your audio system.
If you wish to send six discrete channels into the
e6450, simply use all six inputs and set the “Input
Mode” switch in the “Channel 5 & 6 Controls”
section to “Discrete”.This will most commonly be
accomplished by using the six RCA type connections
(it is possible to use the eight-pin connector with
amplified signals for input into channels 1, 2, 3 & 4
and RCA type connections for input into channels 5
& 6, however, most source units with a dedicated
subwoofer output will also have at least one pair of
full range outputs).
If you wish to feed all six channels by using only
four channels of full-range input, set the “Input
Mode” switch in the “Channel 5 & 6 Controls”
section to “SUM” and use only the inputs to
channels 1, 2, 3 & 4.
connection of component speakers to one, two or
all of the e6450’s channel pairs in a bi-amplified
system.
2) “Filter Freq. (Hz)”The filter frequency
markings surrounding this rotary control are for
reference purposes and are generally accurate to
within 1/3 octave or better. If you would like to
select the filter cutoff frequency with a higher level of
precision, consult the chart in Appendix B (page 13).
Tuning Hint: If you are using the e6450 to drive a
subwoofer system (“LP” mode), a component
satellite speaker system (“HP”mode) or both,
100 Hz is a good baseline “Filter Freq. (Hz)”
setting. After properly adjusting the “Input Sens.”,
as outlined in Appendix A (page 12), you can fine
tune the “Filter Freq. (Hz)” control to achieve the
desired system frequency response.
If you wish to feed all six channels by using two
channels of full-range input and two channels of low-
frequency input (subwoofer output from the source
unit), set the “Input Mode” switch in the “Channel 5
& 6 Controls” section to “Discrete”. It will be
necessary to split the full-range signals with
6
JL AUDIO e6450
JL AUDIO e6450
7
BASS BOOST CONTROLS
only information or the sum of the information
from both the right and left channels. In order to
achieve one of these options, configure the inputs
to that pair of channels in one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a Left-only or
Right-only signal to a pair of the e6450’s channels,
use a “Y-Adaptor” to split the single channel signal
into both left and right RCA inputs (or parallel-
connect both positive and both negative high-level
input connections to a single channel source signal).
This option is useful when using one pair of the
e6450’s channels to drive left channel speakers only
and another pair of the e6450’s channels to drive
right channel speakers only.
1) “Power” (Green): lights to indicate that the
amplifier is turned on and operating normally.
2) “Protect” (Red): lights or flashes to indicate
that the amplifier protection circuitry has been
activated to prevent product failure.
a) If the red “Protect” indicator lights steadily
(without flashing), the amplifier has exceeded its safe
operating temperature.This causes the amplifier to
shut off in order to protect its circuitry. When the
amplifier’s temperature drops to a safe level, the red
“Protect” indicator will shut off and the amplifier
will return to normal operation.
IMPORTANT
!
Speaker loads below 2Ω nominal per channel
are not recommended and may cause the amplifier
to initiate a protection mode and shut itself off.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the output
of two amplifier channels to drive a single load.
When bridged, each channel produces signals of
equal magnitude, but opposite polarity.The
combined output of the two channels provides
twice the output voltage available from a single
channel.The e6450 has been designed for bridging
of its channel pairs without the need for input
inversion adaptors.
To bridge a pair of channels, use the “Left +” and
“Right –” speaker connectors only (the “Left –”
and “Right +” remain unused).When bridged, each
channel will deliver optimum power into a 4Ω load.
1) Bass Boost (Channels 5&6): This switch
allows the user to activate a 6 dB boost centered
at 48 Hz for channels 3&4.When the “Bass Boost”
in the “Channel 5 & 6 Controls” section is
activated, the inputs to “CH 5 (Left)” and “CH 6
(Right)” are summed to create a mono signal. The
“Filter Mode” switch in the “Channel 5 & 6” section
must be in the “LP” position for the bass boost to
be functional.
2) Remote Bass Port: This port allows you to
connect an optional remote boost knob (sold
separately, JL Audio Model RBC-1) that can be
mounted in the front of the vehicle. With the
RBC-1 connected, the boost is no longer limited to
0 or +6 dB, allowing a range of 0 - 12 dB of boost
to be selected.
b) If the red “Protect” indicator flashes
intermittently, the protection circuitry has detected a
short-circuit or a dangerously low impedance
connected to the amplifier output(s). Connecting
the speaker outputs to an impedance lower than
2Ω stereo (4Ω bridged) will cause this protection
mode to activate.The amplifier’s output may cycle
on and off when this protection mode is activated.
When the problem is eliminated, the amplifier will
return to normal operation.
IMPORTANT
!
When parallel-connecting both positive and both
negative high-level input connections as described
above, make sure to connect negative (–) wires to
negative (–) wires and positive (+) wires to positive
(+) wires.
IMPORTANT
!
When a pair of channels are bridged, they will
deliver 150W x 1 into a 4Ω load or 90W x 1 into
an 8Ω load. Operating a pair of bridged channels
into a load lower than 4Ω is not recommended.
2) Left + Right Channel Information: When
bridged and fed by a stereo input, a pair of the
e6450’s channels will automatically combine the left
and right channels into a summed mono (left +
right) channel.This option is useful when using a pair
of the e6450’s channels to drive a subwoofer
system or a summed mono center channel.
SERVICINGYOUR JL AUDIO AMPLIFIER
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses
inside the amplifier.The unique nature of the
circuitry in the JL Audio amplifiers requires
specifically trained service personnel. Do not
attempt to service the amplifier yourself or
through unauthorized repair facilities.This will not
only void the warranty, but may result in the
creation of more problems within the amplifier.
Because a bridged pair of channels requires that
both channels receive input, you need to connect
both left and right inputs to the source unit.
Connection of only one input will result in reduced
power output, increased distortion and can cause
the amplifier to overheat. Do not do this!
SPEAKER OUTPUTS
The e6450’s speaker outputs are designed to
accept 8 AWG - 16 AWG wire.
Each pair of the e6450’s channels are designed
to deliver power into speaker loads equal to or
greater that 2Ω when using a “stereo” configuration
and speaker loads equal to or greater than 4Ω
when using a “bridged” configuration.
AMPLIFIER STATUS INDICATOR LIGHTS /
PROTECTION CIRCUITRY
There are two status indicator lights on the
input / control end of the amplifier:
When a pair of the e6450’s channels are
operating in bridged mode, the output will be in
mono (only one channel).This mono channel can
contain right channel only information, left channel
If you have any questions about the installation or
setup of the amplifier not covered in
this manual, please contact your dealer or the
JL AUDIO Technical Department for assistance:
(954) 443-1100
9:00 AM – 5:30 PM Eastern Time,
Monday – Friday
8
JL AUDIO e6450
JL AUDIO e6450
9
SYSTEM CONFIGURATIONS
The e6450 is a flexible amplifier, well-suited for a
multitude of system configurations. In this section, the
most likely configurations are explained in detail.
Once you have selected your desired
configuration, you can use the amplifier panel
drawing on pages 16 & 17 to mark the required
switch positions for easy reference.
2 (Right)” inputs and the second pair of stereo
source unit outputs is connected to the
“CH 3 (Left)” and “CH 4 (Right)” inputs of the
e6450 (select “SUM” on the “Input Mode” switch in
the “Channel 5 & 6 Controls” section).
Result: the relative level of the LF and HF channels will
be fixed by the e6450’s “Input Sens.” settings and will
not be user adjustable from the front of the vehicle.
“CH 2 (Right)” inputs, the second pair of stereo
source unit outputs is connected to the
“CH 3 (Left)” and “CH 4 (Right)” inputs and the
source unit’s dedicated subwoofer output is
connected to the “CH 5 (Left)” and “CH 6 (Right)”
inputs (select “Discrete” on the “Input Mode”
switch in the “Channel 5 & 6 Controls” section).
Result: in this mode, the user has the ability to
control the absolute level of the LF channels as well
as both pairs of HF channels.
BI-AMPLIFIED SYSTEMS
Bi-amplified systems are defined as systems in
which separate amplifier channels drive low-frequency
(LF)and high-frequency (HF) speakers and are
separately filtered to send appropriate frequency
ranges to each speaker system.
The most common application of bi-amplification
in mobile audio is to drive a subwoofer system from
one or more amplifiers or channels and component
speakers from separate amplifiers or channels.
The e6450 is designed to work as the only
amplifier in a bi-amplified system.
C) Fade Subwoofer Level vs. HF Level
Required: a basic source unit or processor with two
pairs of stereo outputs.
IMPORTANT
!
Input Connections: the first stereo pair of source
unit outputs each split with a “Y-Adaptor” allowing
the left signal to be sent to the “CH 1 (Left)” and
“CH 3 (Left)” inputs and the right signal to be sent
to the “CH 2 (Right)” and “CH 4 (Right)” inputs
of the e6450.The second stereo pair of source unit
outputs is connected to the “CH 5 (Left)” and
“CH 6 (Right)” inputs (select “Discrete” on the
“Input Mode” switch in the “Channel 5 & 6
Controls” section).
Result: in this mode, the user has the ability to fade
or control the level of the LF channels relative to
the HF channels via the source unit’s fader control
without exceeding the maximum clean output level
set by each amplifier section’s “Input Sens.” controls.
D) Subwoofer Level Control Only
Required: a source unit or processor with one pair of
stereo outputs and dedicated subwoofer outputs.
Input Connections: the stereo pair of source unit
outputs each split with a “Y-Adaptor” allowing the
left signal to be sent to the “CH 1 (Left)” and “CH
3 (Left)” inputs and the right signal to be sent to the
“CH 2 (Right)” and “CH 4 (Right)” inputs of the
e6450.The source unit’s dedicated subwoofer
outputs are connected to the “CH 5 (Left)” and
“CH 6 (Right)” inputs (select “Discrete” on the
“Input Mode” switch in the “Channel 5 & 6
Controls” section).
When using a source unit’s dedicated subwoofer
output, set the “Input Sens.” of any channels
receiving input from the subwoofer output with the
source unit’s subwoofer level control set at 3/4 of full
output. See Appendix A (page 12) for details.
Crossover Setup for Bi-Amplified System
with one e6450:
Once the input sections have been configured
appropriately, go to the “Channel 5 & 6 Controls”.
Select “LP” (low-pass) on the “Filter Mode” switch
and an appropriate “Filter Freq.” (100 Hz is a good
starting point).
Next, turn your attention to the “Channel 1 & 2
Controls” and “Channel 3 & 4 Controls” and
select “HP” (high-pass) on the “Filter Mode”
switches and an appropriate “Filter Freq.” (again,
100 Hz is a good starting point).
After proper adjustment of the “Input Sens.”
controls for all three channel pairs using the method
shown in Appendix A (page 12), you can fine tune
filter frequencies and attenuate any pair of channels
to achieve proper balance. For precise filter frequency
information refer to Appendix B (page 13).
BI-AMPLIFIED SYSTEMWITHTHE e6450
In this configuration, channels 5&6 of the e6450 will
drive subwoofers (stereo 75W x 2 at 2Ω or bridged
150W x 1 at 4Ω) with low-pass filtering. Channels
1&2 and channels 3&4 will drive component speakers
in stereo (75W x 4 at 2Ω) with high-pass filtering.
Input connection options for a bi-amplified system with
one e6450 are as follows:
A) No User Adjustability
Required: a basic source unit or processor with a
single pair of stereo outputs.
Input Connections: a single pair of stereo source
unit outputs each split with a “Y-Adaptor” allowing
the left signal to be sent to the “CH 1 (Left)” and
“CH 3 (Left)” inputs and the right signal to be sent
to the “CH 2 (Right)” and “CH 4 (Right)” inputs
of the e6450 (select “SUM” on the “Input Mode”
switch in the “Channel 5 & 6 Controls” section).
Result: the relative level of the LF and HF channels will
be fixed by the e6450’s “Input Sens.” settings and will
not be user adjustable from the front of the vehicle.
B) Fade Front vs. Rear with no Subwoofer
Level Control
Result: in this mode, the user has the ability to
control the absolute level of the LF channels relative
to the HF channels.
E) Independent level control of all three
channel pairs
Required: a basic source unit or processor with two
pairs of stereo outputs.
Input Connections: one pair of stereo source unit
outputs is connected to the “CH 1 (Left)” and “CH
Required: a source unit or processor with two pairs
of stereo outputs and dedicated subwoofer outputs.
Input Connections: one pair of stereo source unit
outputs is connected to the “CH 1 (Left)” and
10
JL AUDIO e6450
JL AUDIO e6450
11
APPENDIX A:
APPENDIX B:
APPENDIX C:
Input Sensitivity Level Setting
Precise Frequency Selection Chart
e6450 Specifications
“FILTER FREQ” AMP FILTER
Following the directions below will allow the
installer to adjust the input sensitivity of each
amplifier channel pair simply and easily in just a few
minutes using equipment which is commonly
available in installation bays.
9) Once you have adjusted the e6450 to its
maximum low-distortion output level, reconnect
the speaker(s).The “Input Sens.” controls can now
be adjusted downward if the amplifier requires
attenuation to achieve the desired system balance.
GENERAL SPECIFICATIONS:
Recommended FuseValue: 60A
Detent
Number
Panel
Marking
Actual
Freq.
Recommended Fuse Type: AGU or MaxiFuse™
Full counter-clockwise: 53
01 . . . . . . . . . . . . . . . . . . . . . . . .53
02 . . . . . . . . .“50” . . . . . . . . .53
03 . . . . . . . . . . . . . . . . . . . . . . . .53
04 . . . . . . . . . . . . . . . . . . . . . . . .54
05 . . . . . . . . . . . . . . . . . . . . . . . .54
06 . . . . . . . . . . . . . . . . . . . . . . . .55
07 . . . . . . . . . . . . . . . . . . . . . . . .55
08 . . . . . . . . .“55” . . . . . . . . .56
09 . . . . . . . . . . . . . . . . . . . . . . . .56
10 . . . . . . . . . . . . . . . . . . . . . . . .57
11 . . . . . . . . . . . . . . . . . . . . . . . .58
12 . . . . . . . . . . . . . . . . . . . . . . . .59
13 . . . . . . . . . . . . . . . . . . . . . . . .62
14 . . . . . . . . .“60” . . . . . . . . .65
15 . . . . . . . . . . . . . . . . . . . . . . . .65
16 . . . . . . . . . . . . . . . . . . . . . . . .66
17 . . . . . . . . . . . . . . . . . . . . . . . .70
18 . . . . . . . . . . . . . . . . . . . . . . . .73
19 . . . . . . . . . . . . . . . . . . . . . . . .77
20 . . . . . . . . .“80” . . . . . . . . .81
21 . . . . . . . . . . . . . . . . . . . . . . . .84
22 . . . . . . . . . . . . . . . . . . . . . . . .88
23 . . . . . . . . . . . . . . . . . . . . . . . .94
24 . . . . . . . . . . . . . . . . . . . . . . .101
25 . . . . . . . . . . . . . . . . . . . . . . .104
26 . . . . . . . . .“120” . . . . . . . .115
27 . . . . . . . . . . . . . . . . . . . . . . .118
28 . . . . . . . . . . . . . . . . . . . . . . .128
29 . . . . . . . . . . . . . . . . . . . . . . .137
30 . . . . . . . . . . . . . . . . . . . . . . .146
31 . . . . . . . . . . . . . . . . . . . . . . .164
32 . . . . . . . . .“150” . . . . . . . .177
33 . . . . . . . . . . . . . . . . . . . . . . .193
34 . . . . . . . . . . . . . . . . . . . . . . .197
35 . . . . . . . . . . . . . . . . . . . . . . .209
36 . . . . . . . . . . . . . . . . . . . . . . .213
37 . . . . . . . . . . . . . . . . . . . . . . .216
38 . . . . . . . . .“200” . . . . . . . .218
39 . . . . . . . . . . . . . . . . . . . . . . .225
Full-clockwise: 225
INPUT SECTIONS:
No. of Inputs: Three Stereo Pairs
Input Type: Differential, noise-cancelling with RCA jack
inputs (low-level, three pairs) and multi-pin jack
(high-level, two pairs)
Necessary Equipment
• Digital ACVoltmeter
IMPORTANT
!
• CD with a sine-wave test tone recorded at 0 dB
reference level in the frequency range to be
amplified for that set of channels (50 Hz for
subwoofer channels, 1 kHz for a midrange
application). Do not use attenuated test tones
(-10 dB, -20 dB, etc.).
Do not increase any “Input Sens.” setting for
any amplifier channel or channel pair in the system
beyond the maximum level established during this
procedure. Doing so will result in audible
distortion and possible speaker damage.
It will be necessary to re-adjust the
“Input Sens.” for the affected channels if any
equalizer boost is activated after setting the
“Input Sens.” with this procedure.This applies to
any EQ boost circuit, including source unit tone
controls or EQ circuits. EQ cuts will not require
re-adjustment.
Input Range: 200mV - 8V RMS
AMPLIFIER SECTION:
Amplifier Topology: Class AB with patented Absolute
Symmetry™ dual N-Channel MOSFET output design
Power Supply: Unregulated MOSFET switching type
Rated Power (Stereo):
The Nine-Step Procedure
1) Disconnect the speaker(s) from the
amplifier’s speaker output connectors.
45W RMS x 6 @ 4Ω (12.5V)
75W RMS x 6 @ 2Ω (12.5V)
2)Turn off all processing (bass/treble, loudness,
EQ, etc.) on the source unit, processors (if used)
and amplifier. Set fader control to center position
and subwoofer level control to 3/4 of maximum (if
used to feed the e6450).
3)Turn the “Input Sens.” control all the
way down.
4) Set the source unit volume to 3/4 of full
volume. This will allow for reasonable gain overlap
with moderate clipping at full volume.
5) Using the chart on this page, determine the
target voltage for input sensitivity adjustment
according to the nominal impedance of the speaker
system connected to the amplifier outputs.
6)Verify that you have disconnected the
speakers before proceeding. Play a track with an
appropriate sine wave (within the frequency range
to be amplified by the e6450) at 3/4 source
unit volume.
7) Connect the AC voltmeter to the speaker
output connectors of the amplifier. If the channel
pair is operating in stereo, it is only necessary to
measure one channel. If bridged, make sure you test
the voltage at the correct connectors (L+ and R–).
8) Increase the “Input Sens.” control until the
target voltage is observed with the voltmeter.
Rated Power (Bridged):
90W RMS x 3 @ 8Ω (12.5V)
150W RMS x 3 @ 4Ω (12.5V)
THD at Rated Power: <0.08% @ 4 ohms per channel
(20 Hz - 20 kHz)
Nom.
Target ACVoltage
Impedance Stereo
Bridged
Signal to Noise Ratio: >104 dB referred to rated power
(A-weighted, 20 Hz-20 kHz noise bandwidth)
Frequency Response: 10 Hz - 25 kHz (+0, -1dB)
Damping Factor: >200 @ 4Ω per ch./50 Hz,
>100 @ 2Ω per ch. /50 Hz
8Ω
6Ω
4Ω
3Ω
2Ω
13.4V
13.4V
13.4V
12.8V
12.3V
26.8V
25.6V
24.6V
not recommended
not recommended
Slew Rate: 22V/µs
AMPLIFIER FILTER:
Filter Type: State-variable, 12dB/octave Butterworth with
continuously variable cutoff frequency selection from
50-200 Hz. Configurable as Low-Pass or High-Pass.
Defeatable.
DIMENSIONS (LxWxH):
17.7" x 9.25" x 2.36" (450mm x 235mm x 60mm)
Due to ongoing product development, all specifications are
subject to change without notice.
12
JL AUDIO e6450
JL AUDIO e6450
13
APPENDIX D: TROUBLE SHOOTING
“MY AMPLIFIER DOESN’TTURN ON”
“MY AMPLIFIERTURNS ON, BUTTHERE IS NO OUTPUT”
Check the input signal using an AC voltmeter to measure the voltage
Check to make sure there is +12V at the “Remote” connection of
the amplifier. In some cases, the turn-on lead from the source
unit is insufficient to turn on multiple devices and the use of a
relay is required. To test for this problem, jump the “+12V”
wire to the “Remote” terminal to see if the amplifier turns on.
If this does not work, proceed to the next step.
from the source unit while an appropriate test tone is played
through the source unit (disconnect the input cables from the
amplifier prior to this test).The frequency used should be in
the range that is to be amplified by the amplifier
(example: 50 Hz for a sub bass application or 1 kHz for a full
range / high-pass application). A steady, sufficient voltage
(between 0.2 and 8.0-volts) should be present at the output of
the signal cables.
Check the fuse, not just visually, but with a continuity meter. It is
possible for a fuse to have poor internal connections that
cannot be found by visual inspection. It is best to take the fuse
out of the holder for testing. If no problem is found with the
fuse, inspect the fuse-holder.
Check the output of the amplifier. Using the procedure explained in
the previous check item (after plugging the input cables back
into the amplifier) test for output at the speaker outputs of the
amplifier. Unless you enjoy test tones at high levels, it is a good
idea to remove the speaker wires from the amplifier while
doing this. Turn the volume up approximately half way.
5V or more should be measured at the speaker outputs. This
output level can vary greatly between amplifiers but it should
not be in the millivolt range with the source unit at half
volume. If you are reading sufficient voltage, check your speaker
connections as explained below.
“I GET A DISTORTED / ATTENUATED SOUND COMING OUT OFTHE SPEAKER(S)”
Check the speaker wires for a possible short, either between the
positive and negative leads or between either speaker lead and
the vehicle’s chassis ground. If a short is present, you will
experience distorted and/or attenuated output.The “Protect”
light may also illuminate in this situation. It may be helpful to
disconnect the speaker wires from the amplifier and use a
different set of wires connected to a test speaker.
Check the nominal load impedance to verify that each channel
of the amplifier is driving a load equal to or greater than
2Ω (4Ω bridged).
Check the input signal and input signal cables to make sure signal is
present at the “Amplifier Inputs” and the cables are not
pinched or loose. It may be helpful to try a different set of
cables and/or a different signal source to be sure.
Check to ensure that the speaker wires are making a good
connection with the metal inside the terminal block. The
speaker wire connectors are designed to accept up to 12
AWG wire. Make sure to strip the wire to allow for a
sufficient connection with the metal inside the terminal block.
“MY AMPLIFIER’S OUTPUT FLUCTUATES WHEN ITAP ON IT OR HIT A BUMP”
Check the connections to the amplifier. Make sure that the insulation
for all wires has been stripped back far enough to allow a
“MY AMPLIFIER SHUTS OFF ONCE IN A WHILE, USUALLY AT HIGHERVOLUMES”
Check your voltage source and grounding point.The power supply of
the e6450 will operate with charging system voltages down to
8V. Shutdown problems at higher volume levels can occur
when the charging system voltage drops below 8V.These dips
can be of very short duration making them extremely difficult
to detect with a common DC voltmeter.To ensure proper
voltage, inspect all wiring and termination points. It may also be
necessary to upgrade the ground wire connecting the battery
to the vehicle’s chassis and the power wire connecting the
alternator to the battery. Many vehicles employ small
good contact area inside the terminal block.
Check the input connectors to ensure that they all are making good
contact with the input jacks on the amplifier.
“HOW DO I PROPERLY SETTHE INPUT SENSITIVITY ON MY AMPLIFIER”
Please refer to Appendix A (page 12) to set the input sensitivity for
maximum, low-distortion output.
(10 AWG - 6 AWG) wire to ground the battery to the vehicle’s
chassis and to connect the alternator to the battery.To prevent
voltage drops, these wires should be upgraded to 4 AWG
when installing amplifier systems with main fuse ratings above
60A. Grounding problems are the leading cause of
mis-diagnosed amplifier failures.
14
JL AUDIO e6450
JL AUDIO e6450
15
INSTALLATION NOTES:
Use this diagram to document your amplifier’s switch and control positions.
16
JL AUDIO e6450
JL AUDIO e6450
17
18
JL AUDIO e6450
JL AUDIO e6450
19
LIMITEDWARRANTY - AMPLIFIERS (USA)
JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of ninety
(90) days from the original date of purchase.The warranty term is extended to two (2) years if installation is
performed or approved by an authorized JL AUDIO dealer (proof of installation or approval required on
purchase receipt).
This warranty is not transferrable and applies only to the original purchaser from an authorized JL AUDIO
dealer. Should service be necessary under this warranty for any reason due to manufacturing defect or
malfunction, JL AUDIO will (at its discretion), repair or replace the defective product with new or remanufactured
product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse,
product modification or neglect, failure to follow installation instructions, unauthorized repair attempts,
misrepresentations by the seller.This warranty does not cover incidental or consequential damages and does not
cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear
is not covered under warranty.
Warranty is void if the product’s serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided
herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied,
shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these
exclusions may not apply to you.This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL AUDIO ’s Amplifier Service Facility freight-prepaid through an
authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original sales receipt).
Direct returns from consumers or non-authorized dealers will be refused unless specifically authorized by
JL AUDIO with a valid return authorization number.
Warranty expiration on products returned without proof of purchase will be determined from the
manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Non-defective
items received will be returned freight-collect. Customer is responsible for shipping charges and insurance in
sending the product to JL AUDIO. Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call:
JL Audio customer service: (954) 443-1100
during normal business hours (9:00 AM – 5:30 PM Eastern Time)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025
(do not send product for repair to this address)
InternationalWarranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
™
Absolute Symmetry Class AB Amplifier Circuit is covered by U.S. Patent #6,294,959 and is
pending in the countries listed below. Austria,Belgium,Brazil,Canada,China,France,Germany,Indonesia,
Italy, Japan, Republic of Korea, Mexico, Netherlands, Norway, Russian Federation, Singapore, Sweden,
Switzerland, United Kingdom, and all other PCT countries.
e6450MAN-CH-03-2003
|