USER MANUAL
ENGLISH
DEUTSCH
FRANCAIS
NEDERLANDS
ITALIANO
Thank you very much for choosing the iiyama
LCD monitor.
We recommend that you take a few minutes to
read carefully through this brief but
comprehensive manual before installing and
switching on the monitor. Please keep this
manual in a safe place for your future
reference.
Congratulations!
You have just purchased a TCO’99 approved and labelled
product! Your choice has provided you with a product developed
for professional use. Your purchase has also contributed to
reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation
of goods and services to the environment. The main problem, as far as computers and other electronics
equipment are concerned, is that environmentally harmful substances are used both in the products and during
their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment,
most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions,
radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously
and thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’99 scheme which provides for international and environmental
labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish
Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature
Conservation) and Statens Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric
and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must
be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be
adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction of
electric and magnetic fields, physical and visual ergonomics and good usability.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO’99 approved and labelled products may also be
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to
prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of
flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are
chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing
bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive
damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have
been found in human blood and researchers fear that disturbances in foetus development may occur.
The relevant TCO’99 demand requires that plastic components weighing more than 25 grams must not contain
flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit
boards since no substitutes are available.
Cadmium* *
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays.
Cadmium damages the nervous system and is toxic in high doses. The relevant TCO’99 requirement states
that batteries, the colour-generating layers of display screens and the electrical or electronics components
must not contain any cadmium.
Mercury* *
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic
in high doses. The relevant TCO’99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components associated with the
labelled unit.
CFCs (freons)
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used during the manufacture
and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs
break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on
earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.
Lead* *
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO’99 requirement permits the inclusion of
lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
FCC DECLARATION OF CONFORMITY
Model Number:
Trade Name:
PLH2130/PLH2010/PLH1900
iiyama
Responsible party:
Address:
IIYAMA North America, Inc.
65 West Street Road, Suite 101B, Warminster, PA 18974 U.S.A.
215-682-9050
Telephone number:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for Class B Personal Computers and
peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a residential environment. This device generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If you determine the device does cause harmful interference to radio
or television reception (this may be determined by monitoring the interference while turning the device off and
on), you are encouraged to try to correct the interference by one of the following measures:
ꢀ
ꢀ
ꢀ
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver
is connected.
ꢀ
Consult the dealer or an experienced radio or TV technician for help.
To meet the FCC requirements, you should use a signal cable with ferrite core at both ends.
CAUTION
Changes or modifications not expressly approved by iiyama could void the users authority
to operate the device under FCC compliance regulations.
CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE
STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as
set out in the radio interference regulation of the Canadian department of communications.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,
business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
All places of operation are characterised by their connection to the public low voltage power supply system.
ꢀ We reserve the right to change specifications without notice.
ꢀ All trademarks used in this user manual are the property of their respective owners.
ꢀ This manual is printed on recycled paper.
TABLE OF CONTENTS
FOR YOUR SAFETY ..............................................................................
SAFETY PRECAUTIONS .................................................................
SPECIAL NOTES ON LCD MONITORS .............................................
CUSTOMERSERVICE ......................................................................
CLEANING .......................................................................................
1
1
3
3
3
BEFOREYOU OPERATETHE MONITOR ................................................
FEATURES .......................................................................................
CHECKINGTHE CONTENTS OFTHE PACKAGE .............................
OPTIONALPARTS ...........................................................................
CONTROLSAND CONNECTORS: ProLite H2130 ............................
CONTROLSAND CONNECTORS: ProLite H2010 / ProLite H1900 ..
CONNECTING YOUR MONITOR ProLite H2130 ..............................
4
5
6
6
7
8
9
CONNECTING YOUR MONITOR ProLite H2010 / ProLite H1900 .... 10
PREPARINGTHE SPEAKER: ProLite H2130 .................................... 11
COMPUTERSETTING ....................................................................... 11
ADJUSTING THE HEIGHTANDTHE VIEWINGANGLE ................... 12
PANELROTATION ............................................................................ 12
OPERATINGTHEMONITOR ................................................................... 13
ADJUSTMENTMENUCONTENTS .................................................... 14
SCREENADJUSTMENTS ................................................................. 22
POWER MANAGEMENTFEATURE .................................................. 24
TROUBLE SHOOTING ............................................................................ 25
APPENDIXA ........................................................................................... 26
SPECIFICATIONS: ProLite H2130 .................................................... 26
SPECIFICATIONS: ProLite H2010 .................................................... 27
SPECIFICATIONS: ProLite H1900 .................................................... 28
DIMENSIONS .................................................................................... 29
COMPLIANTTIMING ......................................................................... 30
CONNECTORPINASSIGNMENT ...................................................... 31
APPENDIXB ........................................................................................... 32
We recommend recycling of used product. Please contact your dealer or
iiyama service center. Recycle information is obtained via the Internet, using
You can access the Web page of different countries from there.
FOR YOUR SAFETY
SAFETY PRECAUTIONS
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
and contact your dealer or iiyama service center immediately. Further use may be dangerous and
can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
FOR YOUR SAFETY
1
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage
your computer.
DO NOT PUT FLOPPY DISKS NEAR THE SPEAKERS (For ProLite H2130)
Magnetically recorded data, such as on a floppy disk, may become corrupted by the magnetic field
produced by the speakers if the disks are placed on or near the speakers.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For
optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
2
FOR YOUR SAFETY
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture
position to the correct position.
ꢀ
Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
ꢀ
ꢀ
ꢀ
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours. There is the possibility that the previous screen has been
fixed. Pay attention sufficiently when you use LCD Monitor.
ꢀ
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.
CUSTOMER SERVICE
ꢀ
The fluorescent light used in the LCD monitor may have to be periodically replaced.
NOTE
For the warranty coverage on this component, please check with local iiyama
service center.
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
ꢀ
CLEANING
WARNING
If you drop any materials or liquids such as water into the monitor when cleaning,
ꢀ
unplug the power cable immediately and contact your dealer or iiyama service center.
CAUTION
NOTE
ꢀ For safety reasons, turn off the power switch and unplug the monitor before you clean it.
To protect the LCD panel, do not scratch or rub the screen with a hard object.
ꢀ
Never use any of the following strong solvents. These will damage the cabinet and
ꢀ
the LCD screen.
Spray-type cleaner
Wax
Thinner
Benzine
Acid or Alkaline solvent
Abrasive cleaner
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
ꢀ
CABINET
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
LCD
Periodic cleaning with a soft dry cloth is recommended.
SCREEN
Don't use tissue paper etc. because these will damage the LCD screen.
FOR YOUR SAFETY
3
BEFORE YOU OPERATE THE MONITOR
The monitor functions as a hub when connected to a USB compliant computer and USB peripherals.
However, with older operating systems and/or BIOS settings in your computer, the USB hub may not
operate. In this case, please contact your computer dealer first for advice.
Please stand the monitor and then remove the
stopper pin on the back of the stand slowly while
pushing top face of the stand before you install the
monitor. Careful attention is required as the monitor
is sprung loaded and may expand quickly when
removing it.
Stopper pin
4
BEFORE YOU OPERATE THE MONITOR
FEATURES
ꢀ ProLite H2130: 54cm (21.3") TFT Color LCD Monitor
ꢀ ProLite H2010: 51cm (20.1") TFT Color LCD Monitor
ꢀ ProLite H1900: 48cm (19.0") TFT Color LCD Monitor
ꢀ Supports Resolutions up to 1600 × 1200 (ProLite H1900 supports digital input only.)
ꢀ Super Wide Viewing Angle and High Contrast
ꢀ Economy Mode
Reduced Power Consumption
ꢀ Multi-Color Control
Supports sRGB International Standard
ꢀ Gamma Control
Clear Display for Moving Pictures & Photographs
ꢀ Digital Character Smoothing
ꢀ Automatic Set-up
ꢀ ProLite H2130: Stereo Speakers
2×1.0W Retractable Stereo Speakers & Headphone Connector
ꢀ Plug & Play VESA DDC2B Compliant
Windows® 95/98/Me/2000/XP Compliant
ꢀ DDC-CI Compliant (For Connector ‘INPUT2’ Only)
Display Tune® software enables screen adjustments by computer
ꢀ Power Management (VESA DPMS Compliant)
ꢀ Ergonomic Design
TCO ’03 and MPR 3 Approved
ProLite H2130-W
ProLite H2010-W
ProLite H1900-W
TCO ’99 and MPR 3 Approved
ProLite H2130-B
ProLite H2010-B
ProLite H1900-B
ꢀ Digital Input (DVI-I) for Clear Display
ꢀ Dual Screen Display
Multiple Screen via D-SUB Signal Output
ꢀ USB2.0 Hi-speed Hub Function
ꢀ 90° Panel Rotation Design
ꢀ VESA Mounting Standard (100mm×100mm) Compliant
ꢀ Keyhole for Security Lock
BEFORE YOU OPERATE THE MONITOR
5
CHECKING THE CONTENTS OF THE PACKAGE
The following accessories are included in your package. Check to see if they are enclosed with the monitor.
If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office.
ꢀ Power Cable*1
ꢀ DVI-A Signal Cable DV62*2, DV63*3
ꢀ USB Cable SU43
ꢀ DVI-D Signal Cable DV67*2, DV68*3
ꢀ Audio Cable AD25*4
ꢀ User Manual
ꢀ Cable Cover
ꢀ Sample: Pivot® & Liquid Series software (CD)
Pivot®: This software enables to rotate the orientation of the screen to display in portrait or
landscape mode.
Liquid View®: This software enables to scale icons up.
Liquid SurfTM: This software supports Internet Explorer display.
Consult english.txt in CD-ROM for installation.
ꢀ Sample: Display Tune® software (CD)
This software enables screen adjustments.
Consult english.txt in CD-ROM for installation.
*1 TO USERS IN 120V AREA
CAUTION
The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used.
However, all guarantees and warranties are void for any problems or damage
caused by a power cable not supplied by iiyama.
*2 Accessory for ProLite H2130-W, ProLite H2010-W and ProLite H1900-W
*3 Accessory for ProLite H2130-B, ProLite H2010-B and ProLite H1900-B
*4 Accessory for ProLite H2130-W/B
OPTIONAL PARTS
Optional parts as below are available for your LCD monitor. Please contact your local iiyama dealer
or regional iiyama office for them. The Speaker is attached to the monitor to output a sound from the
computer or the audio equipment. The Video Adapter enables you to connect the video equipment to
the monitor. The Protection Sheet is attached to LCD panel surface to protect it from stains or
scratches. The Calibration Sensor adjusts a color appearance to its setting range.
ꢀ Speaker
ProLite H2010-W/1900-W: OSP1-2 (Bottom) OSP2-2 (Right/Left)
ProLite H2010-B/1900-B: OSP1-2B (Bottom) OSP2-2B (Right/Left)
ꢀ Video Adapter OVA3-1
ꢀ Protection Sheet
ProLite H2130: Parts No. 832Z001-07
ProLite H2010: Parts No. 832Z001-05
ProLite H1900: Parts No. 832Z001-04
ꢀ ii-Style Color Kit: Calibration Sensor, Cable, Software (CD)
6
BEFORE YOU OPERATE THE MONITOR
ProLite H2130
CONTROLS AND CONNECTORS
<Front>
<Back>
Power Indicator
A
Green: Normal operation (ProLite H2130-W)
Blue: Normal operation (ProLite H2130-B)
Orange: Power Management
NOTE
The monitor enters into power management mode which reduces the power
consumption to less than 4W when receiving no horizontal and/or vertical
sync signal.
Power Switch (POWER)
Auto Button (AUTO)
+ / Brightness Button (+ /
– / Contrast Button (– /
Menu Button (MENU)
Input Button (INPUT)
Speakers
B
C
D
E
F
G
H
I
)
)
USB-UP
Connect with a USB compliant computer by the USB Cable attached to the monitor.
USB-DOWN
J
Connect any cables from USB compliant peripherals such as mouse, keyboard, etc.
Audio Connector (AUDIO IN)
K
L
DVI-I 29pin Connector (INPUT 2)
DDC-CI is compliant with INPUT 2 only.
NOTE
DVI-I 29pin Connector (INPUT 1)
M
N
D-SUB mini 15pin Connector (D-SUB OUT)
Output same signal as analog input to INPUT 1.
NOTE
Optional Video Adapter for video input can be connected to D-SUB mini 15pin connector.
Headphone Connector
AC Connector (AC IN)
Main Power Switch
O
P
Q
R
Keyhole for Security Lock
NOTE
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
BEFORE YOU OPERATE THE MONITOR
7
ProLite H2010 / ProLite H1900
CONTROLS AND CONNECTORS
<Back>
<Front>
Power Indicator
A
Green: Normal operation (ProLite H2010-W / ProLite H1900-W)
Blue: Normal operation (ProLite H2010-B / ProLite H1900-B)
Orange: Power Management
The monitor enters into power management mode which reduces the power
NOTE
consumption to less than 4W when receiving no horizontal and/or vertical
sync signal.
Power Switch (POWER)
Auto Button (AUTO)
+ / Brightness Button (+ /
– / Contrast Button (– /
Menu Button (MENU)
Input Button (INPUT)
USB-UP
B
C
D
E
F
G
H
)
)
Connect with a USB compliant computer by the USB Cable attached to the monitor.
USB-DOWN
I
J
Connect any cables from USB compliant peripherals such as mouse, keyboard, etc.
DVI-I 29pin Connector (INPUT 2)
NOTE DDC-CI is compliant with INPUT 2 only.
DVI-I 29pin Connector (INPUT 1)
K
L
D-SUB mini 15pin Connector (D-SUB OUT)
Output same signal as analog input to INPUT 1.
NOTE
Optional Video Adapter for video input can be connected to D-SUB mini 15pin connector.
Optional Speaker Connector (DC OUT)
AC Connector (AC IN)
M
N
O
P
Main Power Switch
Keyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
NOTE
8
BEFORE YOU OPERATE THE MONITOR
ProLite H2130
CONNECTING YOUR MONITOR
Ensure that both the computer and the monitor are switched off.
A
B
Connect the computer to the monitor with the signal cable. (See page 31 for CONNECTOR PIN
ASSIGNMENT.)
Connect the monitor to the USB compliant computer with the USB Cable when using the USB hub
features.
C
D
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
Connect the Power Cable to the monitor first and then to the power supply.
E
NOTE ꢀ The signal cables used for connecting the computer and monitor vary by the type of computer
used. An incorrect connection may cause serious damage to both the monitor and the
computer.
ꢀ For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
ꢀ Make sure you tighten the finger screws at each end of the signal cable.
ꢀ In case your computer is not compatible with USB2.0, the USB hub is compatible with
USB1.1.
ꢀ Cables are connected easily by rotating the panel 90 degrees. (See page 12 for PANEL
ROTATION.)
ꢀ Cables can be bundled together inside the cover at the back of the stand. See page 11 for
cable wiring.
[Example of Connection]
< Back >
Power Cable (Accessory)
Video Adapter OVA3-1
(Optional)
Keyboard
Mouse
Printer
USB Cable SU43 (Accessory)
Audio Cable AD25 (Accessory)
D-SUB Signal Cable (Not included)
Additional Display Monitor
Computer
To DVI connector of
computer
DVI-D Signal Cable DV67/DV68 (Accessory)
or
To D-SUB connector
of computer
DVI-A Signal Cable DV62/DV63 (Accessory)
BEFORE YOU OPERATE THE MONITOR
9
ProLite H2010 / ProLite H1900
CONNECTING YOUR MONITOR
Ensure that both the computer and the monitor are switched off.
A
B
Connect the computer to the monitor with the signal cable.(See page 31 for CONNECTOR PIN
ASSIGNMENT.)
Connect the monitor to the USB compliant computer with the USB Cable when using the USB hub
features.
C
Connect the Power Cable to the monitor first and then to the power supply.
D
NOTE ꢀ The signal cables used for connecting the computer and monitor vary by the type of computer
used. An incorrect connection may cause serious damage to both the monitor and the
computer.
ꢀ For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
ꢀ Make sure you tighten the finger screws at each end of the signal cable.
ꢀ In case your computer is not compatible with USB2.0, the USB hub is compatible with
USB1.1.
ꢀ Cables are connected easily by rotating the panel 90 degrees. (See page 12 for PANEL
ROTATION.)
ꢀ Cables can be bundled together inside the cover at the back of the stand. See page 11 for
cable wiring.
[Example of Connection]
< Back >
Power Cable (Accessory)
Video Adapter OVA3-1
(Optional)
Keyboard
Mouse
Printer
USB Cable SU43 (Accessory)
D-SUB Signal Cable (Not included)
Additional Display Monitor
Computer
To DVI connector of
computer
DVI-D Signal Cable DV67/DV68 (Accessory)
or
To D-SUB connector
of computer
DVI-A Signal Cable DV62/DV63 (Accessory)
10 BEFORE YOU OPERATE THE MONITOR
[Cable Wiring]
Collect cables at the back of the stand.
A
B
Place the cover by inserting the tabs into guide
holes and then sliding the cover downward.
PREPARING THE SPEAKER
ProLite H2130
Pull down the speaker with rotating it forward as indicated below.
COMPUTER SETTING
ꢀ Signal Timing
Change to the desired signal timings listed on page 30 in COMPLIANT TIMING.
ꢀ Windows 95/98/Me/2000/XP Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on
Windows 95/98/Me/2000/XP by connecting the monitor to DDC2B compliant computer with the
Signal Cable supplied. Windows 95/98/Me/2000/XP Monitor Information File for iiyama monitors
may be necessary for your computer and obtained via the Internet, using the address:
NOTE
ꢀ For additional information on how to download the driver for your monitor, please
access one of the internet sites noted above.
ꢀ Monitor Drivers are not required in most cases for Macintosh or Unix operating systems.
For further information, please contact your computer dealer first for advice.
BEFORE YOU OPERATE THE MONITOR 11
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE
ꢀ For optimal viewing it is recommended to look at
the full face of the monitor, then adjust the monitor’s
height and angle to your own preference.
ꢀ Hold the panel so that the monitor does not topple
when you change the monitor’s height or angle.
ꢀ You are able to adjust the monitor's height up to
110mm
110mm, angle up to 35 degrees right and left, 35
degrees upward.
35˚
NOTE ꢀ Do not touch the LCD screen when you
change the height or the angle. It may
cause damage or break the LCD screen.
ꢀ Careful attention is required not to catch
your fingers or hands when you change
the height or the angle.
For ProLite H2130
35˚
35˚
ꢀ The speaker should be retracted when
you use the monitor at lowest position
and minimum angle. If you use the monitor
without retracting the speaker, it may
cause damage because the speaker
touches to the stand.
PANEL ROTATION
Adjust the monitor’s height to the maximum.
Rotate the panel 90 degrees.
A
B
Portrait: Turn clockwise.
Landscape: Turn counter clockwise.
90˚
NOTE ꢀ Attempting to rotate without fully
extending upward may cause
damage to stand.
ꢀ Please use attached Pivot®
software for rotating the image
on the screen.
Adjust the monitor’s angle to your
preference.
C
12 BEFORE YOU OPERATE THE MONITOR
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 30. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 22 for SCREEN ADJUSTMENTS.
Press the Menu Button to start the On Screen Display feature. There are
additional Menu pages which can be switched by using the + / – Buttons.
Displayed while
Economy Mode is active.
Displayed while sRGB is active.
Picture Control
'Screen OSD... Function Info...
Menu page
Adjustment icon
SELECT MENU
-
+
Select the Menu page which contains the adjustment icon relating to the
adjustment you want to make. Press the Menu Button again. Then, use the
+ / – Buttons to highlight the desired adjustment icon.
B
C
Press the Menu Button again. Use the + / – Buttons to make the appropriate
adjustment or setting.
For example, to correct for vertical position, select Menu page of Screen Control and then press
the Menu Button. Then, select
(V-Position) by using the + / – Buttons.
Picture
Screen Control
OSD... Function Info...
AUTO
V-Position
-
+
10
ENTER MENU
+
-
An adjustment scale appears after you press the Menu Button. Use the + / – Buttons to change
the vertical position settings. The vertical position of the overall display should be changing
accordingly while you are doing this.
Picture
Screen Control
OSD... Function Info...
AUTO
The bar shows
the progress of the
adjustment being made.
V-Position
-
-
+
50
EXIT MENU
+
NOTE
ꢀ The On Screen Display disappears several seconds after you stop pressing the buttons while
performing an adjustment.
ꢀ
The On Screen Display disappears immediately when you press the Auto Button.
Any changes are automatically saved in the memory when the On Screen Display disappears.
ꢀ
Turning off the power should be avoided while using the Menu.
Adjustments for Brightness, Contrast, Clock, Phase and Position are saved for each signal timing.
ꢀ
Except for these adjustments, all other adjustments have only one setting which applies to all
signal timings.
OPERATING THE MONITOR 13
ADJUSTMENT MENU CONTENTS
Direct
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
ꢁ Brightness: Press the Brightness Button when the Menu is not displayed.
ꢁ Contrast:
Press the Contrast Button when the Menu is not displayed.
ꢁ Signal Select: Press the Input Button when the Menu is not displayed.
ꢁ Auto Set-up: Press the Auto Button when the Menu is not displayed.
For ProLite H2130
ꢁ Volume:
Press the Menu Button within 5 seconds after pressing the Brightness Button or
the Contrast Button during the direct adjustments above.
SWITCHING BRIGHTNESS / CONTRAST / VOLUME ADJUSTMENT
(The VOLUME adjustment is for ProLite H2130 only.)
ꢀ
NOTE
To switch between Brightness, Contrast and Volume adjustments, press the Menu
Button within 5 seconds after pressing the Brightness Button or the Contrast Button
during the direct adjustments above.
Brightness
Contrast
Volume
SIGNAL SELECT (INPUT1 / INPUT2)
ꢀ
Select either INPUT1 or INPUT2 for the signal input when both of the signal inputs are
connected to a signal source.
In case of selecting “Auto” in the adjustment item: Auto Search,
select INPUT1 or INPUT2 automatically for the signal input by pressing the Input Button.
In case of selecting “Manual” in the adjustment item: Auto Search,
press the Input Button and then the Menu Button. Select the input signal (INPUT1Analog
/ INPUT1 Digital / INPUT2 Analog / INPUT2 Digital) by pressing the + / – Buttons.
14 OPERATING THE MONITOR
Analog / Digital Input
Menu : Picture Control
(Analog / Digital)
Picture Control
'Screen OSD... Function Info...
SELECT MENU
-
+
Adjustment Item
Problem / Option
Button to Press
Brightness *
Too dark
Direct
Too bright
Contrast
Too dull
Direct
Too intense
9300K Bluish white (9300K)
Color Temp. / Matrix
6500K Reddish white (6500K)
R (Red)
Too weak
User
G (Green)
B (Blue)
Too strong
NOTE
Y (Yellow)
M (Magenta)
ꢀ sRGB is an international
standard which defines and
unifies the difference of
color appearance between
equipment.
ꢀ You can not adjust the
Brightness, Contrast and
GammainsRGBmodebecause
those settings are locked.
Too light
Too deep
Matrix
C (Cyan)
sRGB
CAL
sRGB mode
Calibration mode: Color appearance is set to the range
adjusted by an optional calibration sensor.
Normal Normal
Gamma
Hi.Cont High contrast
Dark
User
Dark
Gamma: approx.1.8, 2.0, 2.2 or 2.4 is selected.
Sharpness
1 2 3 4 5
You can change the picture quality from 1 to 5 (soft to sharp).
Press the + Button to change the picture quality in numerical
order. Press the – Button to change the picture quality in reverse
numerical order.
Back-light is too dark
User
Economy Mode
Return to Menu
Back-light is too bright
Mode 1 Brightness of back-light is reduced by Approx.10%.
Mode 2 Brightness of back-light is reduced by Approx.50%.
Highlight “Menu : Picture Control” again.
*
Adjust the User of Economy Mode when you are using the monitor in a dark room and feel the
screen is too bright.
See page 14 for Direct adjustment.
Direct
OPERATING THE MONITOR 15
Menu : Screen Control
(Analog)
Picture
Screen Control
OSD... Function Info...
AUTO
SELECT MENU
-
+
Adjustment Item
Problem / Option
Button to Press
NO
Return to Menu.
Auto Set-up *1
AUTO
Adjust Clock, Phase, V-Position and H-Position
automatically.
YES
Direct
NOTE
The screen becomes dark for approximately five seconds during the adjustment.
Clock *2
To correct flickering text or lines
To correct flickering text or lines
Phase *2
V-Position
H-Position
Return to Menu
Too low
Too high
Too far to the left
Too far to the right
Highlight “Menu : Screen Control” again.
1
*
For best results, use the Auto Set-up in conjunction with the adjustment pattern.
(See page 22 for SCREENADJUSTMENTS.)
2
*
See page 22 for SCREENADJUSTMENTS.
See page 14 for Direct adjustment.
Direct
16 OPERATING THE MONITOR
Menu : Screen Control
(Digital)
Picture
Screen Control
OSD... Function Info...
SELECT MENU
-
+
Adjustment Item
DVI Filter *
Problem / Option
Button to Press
To reduce screen noise
This function should be used to reduce screen noise caused by connecting longer cable
than enclosed one.
NOTE
Return to Menu
Highlight “Menu : Screen Control” again.
*
Available for INPUT1 only.
OPERATING THE MONITOR 17
Menu : OSD & Others
(Analog / Digital)
Picture Screen... OSD & Others
Function Info...
RESET
SELECT MENU
-
+
Problem / Option
1 2 3 4 5
Button to Press
Adjustment Item
OSD Position
You can move the OSD display
area to any one of the following 5
positions within the overall display:
Press the + Button to move the OSD in numerical order. Press
the – Button to move the OSD in reverse numerical order.
OSD Off Timer
OSD Rotation
You can set the OSD display duration
time between 3 and 60 seconds.
OFF
ON
Return to Normal.
Menu screen is rotated 90 degrees in
counterclockwise.
Use this function when using the monitor with portrait orientation.
NOTE
NOTE
OFF
ON
Return to Menu.
All adjustment items are locked out.
Key Lock Mode
To cancel the Key Lock Mode, keep pressing the Menu, + and – Buttons at the same time
for 8 seconds or more.
English
English
Svenska
Swedish
Russian
Chinese
Japanese
Polish
Language
Deutsch
German
Nederlands Dutch
Français
Italiano
French
Italian
Polski
Español
Spanish
NO
Return to Menu.
Reset
RESET
YES
Factory-preset data is restored.
Return to Menu
Highlight “Menu : OSD & Others” again.
18 OPERATING THE MONITOR
Menu : Functions
(Analog / Digital)
Picture Screen... OSD...
Functions
Info...
A B C
ABC
A B C
H
SELECT MENU
-
+
Problem / Option
Button to Press
Adjustment Item
Auto Search
Search the input signal automatically in the following rotation:
INPUT1Analog INPUT1 Digital INPUT2Analog
Auto
Video *1 S Video *1
INPUT2 Digital
Manual
INPUT1
Select the input signal by “Signal Select” function.
Select the Analog input.
Signal Select
Select the Digital input.
Direct
Select the Analog input.
INPUT2
Select the Digital input.
S Video *1 Select the S Video input.
Video *1
1 to 1
Aspect
Full
Select the Video input.
Displayed at the same magnification
Expansion display of Aspect
Expansion display
Full Screen*2
Zoom
Zoom In
Zoom in the image.
Zoom Out Zoom out the image.
To move the zoom point to the right.
H-Position
V-Position
User
To move the zoom point to the left.
To move the zoom point downward.
To move the zoom point upward.
1
3
2
4
4 Multi.
For 4 split screen display by 4 monitors
NOTE
To cancel the “User” settings, press the Auto Button when the setting screen is displayed.
A B C
Flipping
OFF
Return to Normal.
ABC
Mirror
180°
Mirror reversed image is displayed.
The image rotated 180 degrees is displayed.
A B C
LED ON/OFF*3
OFF
ON
LED is turned OFF.
LED is turned ON.
H
Return to Menu
Highlight “Menu : Functions” again.
1
*
For optional video input only. See APPENDIX B.
2
*
You can not select the Aspect when UXGA 1600 × 1200 is input.
Turn OFF the LED when you are bothered by the light in multiple screen environment.
3
*
See page 14 for Direct adjustment.
Direct
OPERATING THE MONITOR 19
The Menu:P in P Control is available only on Analog Input and Digital Input when the
Optional Video Adapter (OVA3-1) is installed in the monitor.
Menu : P in P Control
Pict... Screen OSD.. Func..
P in P Control
Info...
(Analog / Digital)
SELECT MENU
-
+
Adjustment Item
P in P ON
Problem / Option
OFF
P in P function is turned off.
Button to Press
Small
Sub screen is displayed at minimum size.
Sub screen is displayed at normal size.
Sub screen is displayed at maximum size.
Middle
Large
S Video
Video
Display a S Video picture in the sub screen.
Display a Video picture in the sub screen.
P in P Input
P in P H-Position
Sub screen is too far to the left
Sub screen is too far to the right
P in P V-Position
Sub screen is too low
Sub screen is too high
Color of the sub screen is too weak
Color of the sub screen is too strong
P in P Color
P in P Hue
Color of the sub screen is purplish
Color of the sub screen is greenish
Return to Menu
Highlight “Menu : P in P Control” again.
*
Available only when connecting both the computer and the audio equipment to the monitor.
P in P = Picture in Picture:
With this function, you can display two different pictures, such as a picture from the computer
in the main screen and a DVD / Video picture in the sub screen at the same time.
20 OPERATING THE MONITOR
Menu : Information
(Analog / Digital)
Picture Screen... OSD... Function
Information
Model Name
Input Signal
:
:
ProLite H2130
Digital
Signal Timing
:
:
1600 x 1200 60Hz
1:00
Operating Time
-
+
Model Name, Input Signal, Signal
Timing and Operating Time are
displayed.
OPERATING THE MONITOR 21
SCREEN ADJUSTMENTS
ꢀ The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
ꢀ ProLite H2130 and ProLite H2010 are designed to provide the best performance at resolution of
1600 × 1200, but can not provide the best at resolutions of less than 1600 × 1200 because the picture
is automatically stretched to fit the full screen. It is recommended to operate at resolution of 1600 ×
1200 in normal use.
ꢀ ProLite H1900 is designed to provide the best performance at resolution of 1280 × 1024, but can not
provide the best at resolutions of less than 1280 × 1024 because the picture is automatically
stretched to fit the full screen. It is recommended to operate at resolution of 1280 × 1024 in normal use.
ꢀ Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
ꢀ It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
ꢀ Perform adjustments after a warm-up period of at least thirty minutes.
ꢀ Additional adjustments may be required after the Auto Set-up depending on the resolution or signal
timing.
ꢀ The Auto Set-up may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Clock and
Phase. The other way is performing each adjustment manually.
Perform the Auto Set-up first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Set-up, manual adjustments are required. Both adjustments should be made by
using the screen adjustment patterns in the Adjustment Program obtained via the iiyama web site
This manual explains adjustment under Windows 95/98/Me/2000/XP.
Start “Adjustment Program”.
A
B
Select the resolution for your monitor and the adjustment pattern appears.
[Adjustment pattern]
Color bar
Zebra pattern
Picture frame
16-level gray scale
22 OPERATING THE MONITOR
C Press the Auto Set-up Button.
D Adjust the image manually by following procedure below when the screen has a
flicker or blur, or the picture does not fit in the display area after performing the Auto
Set-up.
E Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
F Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.
G Select “Position” in the Adjustment Program and adjust the H-Position and V-Position
so that the frame of the cross-hatch pattern fits into the display area.
NOTE ꢀ When the left side of the picture frame moves away from the left edge of the display
area during the Clock adjustment, adjust Clock and H-Position alternately.
ꢀ Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
ꢀ The picture may flicker during the Clock, H-Position and V-Position adjustment.
ꢀ In case the picture frame is bigger or smaller than the data display area after the Clock
adjustment, repeat steps from C.
ꢀ In the case that a strong flicker or blurs remain on a part of the screen, repeat the
adjustments from E to readjust the Clock. If the flicker or blurs still remain then set the
refresh rate to 60Hz and repeat the adjustments from step C.
ꢀ Adjust the H-Position after the Phase adjustment if the horizontal position moves
during the adjustment.
OPERATING THE MONITOR 23
H Select “Brightness” in the Adjustment Program and adjust the Brightness and
Contrast so that all 16 levels of gray in the grayscale pattern are visible.
Click on “FINISH” to close the Adjustment Program.
POWER MANAGEMENT FEATURE
The power management feature of this product complies with every power saving requirement of
VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the
monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system
manual for information on how this can be configured.
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the
monitor enters into Power Management Mode which reduces the power consumption to less than
4W. The screen becomes dark, and the power indicator turns to orange. From Power Management
Mode, the image reappears in several seconds when either the keyboard or the mouse are
touched again.
Power Indicator
Green/
Blue
NORMAL MODE
POWER MANAGEMENT MODE
Orange
POWER
0
4W
100%
CONSUMPTION
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.
NOTE
ꢀ
ꢀ
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly.
24 OPERATING THE MONITOR
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you
have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
3.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for
further assistance.
Problem
Check
The picture does
not appear.
A
ꢂ The Power Cable is firmly seated in the socket.
ꢂ The Power Switch is turned ON.
(Power indicator
does not light up.)
ꢂ The AC socket is live. Please check with another piece of equipment.
(Power indicator
is green/blue.)
ꢂ If the blank screen saver is in active mode, touch the keyboard or the
mouse.
ꢂ Increase the Contrast and/or Brightness.
The computer is ON.
ꢂ
ꢂ The Signal Cable is properly connected.
ꢂ The signal timing of the computer is within the specification of the monitor.
(Power indicator ꢂ If the monitor is in power management mode, touch the keyboard or the
is orange.)
mouse.
If the input video signal selection is different, switch the Signal Select.
The computer is ON.
ꢂ
ꢂ
ꢂ The Signal Cable is properly connected.
ꢂ
The signal timing of the computer is within the specification of the monitor.
The screen is not ꢂ The Signal Cable is properly connected.
B
synchronized.
ꢂ The signal timing of the computer is within the specification of the monitor.
ꢂ The video output level of the computer is within the specification of the
monitor.
The screen
position is not in
the center.
ꢂ The signal timing of the computer is within the specification of the monitor.
C
D
E
The screen is
too bright or too
dark.
ꢂ The video output level of the computer is within the specification of the
monitor.
ꢂ The power voltage is within the specification of the monitor.
ꢂ The signal timing of the computer is within the specification of the monitor.
The screen is
shaking.
TROUBLE SHOOTING 25
APPENDIX A
SPECIFICATIONS
Model Name
LCD Panel Driving system
Size
ProLite H2130
a-Si TFT Active Matrix
Diagonal: 54cm / 21.3"
0.27mm H × 0.27mm V
280cd/m2 (Typical)
Pixel pitch
Brightness
Contrast ratio
500 : 1 (Typical)
Viewable angle Right / Left / Up / Down: 85 degrees each (Typical)
Response time 20ms (Black, white, black)
Display Colors
Approx. 16.77 million
Analog: Horizontal 24.0-82.0kHz, Vertical 56.0-85.0Hz
Digital: Horizontal 31.0-82.0kHz, Vertical 50.0-85.0Hz
Sync Frequency
Dot Clock
162MHz maximum
Maximum Resolution
Input Connector
Output Connector
Plug & Play
1600 × 1200 maximum, 2 MegaPixels
Dual DVI-I 29pin
D-SUB mini 15pin
VESA DDC2BTM , DDC-CI
Separate sync: TTL, Positive or Negative
Composite sync: TTL, Positive or Negative
Sync on green: 0.3Vp-p, Negative
Input Sync Signal
Analog: 0.7Vp-p (Standard), 75W, Positive
Input Video Signal
Digital: DVI (Digital Visual Interface standard Rev.1.0) compliance
Analog: 0.7Vp-p (Standard), 75W, Positive
Output Video Signal
Maximum Screen Size
432mm W × 324mm H / 17.0" W × 12.8" H
USB Standard
Connectors
Rev. 2.0 / 1.1 compliance
Self-powered Hi-speed hub
Upstream: Series B, Downstream: Series A
1 Upstream (For computer), 4 Downstream (For peripherals)
ø 3.5mm stereo mini jack
Number of USB Ports
Input Audio Connector
Input Audio Signal
Speaker
0.7Vrms maximum
1.0W × 2 (Stereo speakers)
Headphone Connector
Power Source
ø 3.5mm stereo mini jack
100-230VAC, 50 / 60Hz, 0.75-0.34A
70W maximum, Power management mode: 4W maximum*
Power Consumption
Dimensions
Net Weight
466.0× 418.5-528.5 × 241.0mm / 18.3 × 16.5-20.8 × 9.5" (W×H×D)
10.2kg / 22.5lbs
Right / Left: 35 degrees each, Up: 35 degrees
Tilt Angle
Environmental
Considerations
Operative temperature:
Storage temperature:
5 to 35°C / 41 to 95°F
-20 to 60°C / -4 to 140°F
Humidity (-20 to under 50°C / -4 to under 122°F) :
20 to 85% (No condensation)
Humidity (50 to 60°C / 122 to 140°F) : 20 to 55% (No condensation)
Approvals
TCO ’03(ProLite H2130-W),TCO ’99(ProLite H2130-B), CE, TÜV-GS,
MPR3(prEN50279) / ISO 13406-2, FCC-B, UL, CSA, VCCI-B
NOTE
* Condition: USB peripherals or audio equipment are not connected.
26 APPENDIX A
Model Name
LCD Panel Driving system
Size
ProLite H2010
a-Si TFT Active Matrix
Diagonal: 51cm / 20.1"
0.255mm H × 0.255mm V
300cd/m2 (Typical)
Pixel pitch
Brightness
Contrast ratio
700 : 1 (Typical)
Viewable angle Right / Left / Up / Down: 88 degrees each (Typical)
Response time 16ms (Black, white, black), 10ms (Gray, Gray)
Display Colors
Approx. 16.77 million
Sync Frequency
Analog: Horizontal 24.0-82.0kHz, Vertical 56.0-85.0Hz
Digital: Horizontal 31.0-82.0kHz, Vertical 50.0-85.0Hz
Dot Clock
162MHz maximum
Maximum Resolution
Input Connector
Output Connector
Plug & Play
1600 × 1200 maximum, 2 MegaPixels
Dual DVI-I 29pin
D-SUB mini15pin
VESA DDC2BTM , DDC-CI
Input Sync Signal
Separate sync: TTL, Positive or Negative
Composite sync: TTL, Positive or Negative
Sync on green: 0.3Vp-p, Negative
Input Video Signal
Analog: 0.7Vp-p (Standard), 75W, Positive
Digital: DVI (Digital Visual Interface standard Rev.1.0) compliance
Analog: 0.7Vp-p (Standard), 75W, Positive
Output Video Signal
Maximum Screen Size
408mm W × 306mm H / 16.1" W × 12.0" H
USB Standard
Connectors
Rev. 2.0 / 1.1 compliance
Upstream: Series B, Downstream: Series A
Self-powered Hi-speed hub
Number of USB Ports
Power Source
1 Upstream (For computer), 4 Downstream (For peripherals)
100-230VAC, 50 / 60Hz, 0.75-0.34A
Power Consumption
70W maximum, Power management mode: 4W maximum*
Dimensions
Net Weight
466.0 × 424.0-534.0 × 241mm / 18.3 × 16.7-21.0 × 9.5" (W×H×D)
9.8kg / 21.6lbs
Tilt Angle
Right / Left: 35 degrees each, Up: 35 degrees
Operative temperature:
Storage temperature:
5 to 35°C / 41 to 95°F
-20 to 60°C / -4 to 140°F
Environmental
Considerations
Humidity (-20 to under 50°C / -4 to under 122°F) :
20 to 85% (No condensation)
Humidity (50 to 60°C / 122 to 140°F) : 20 to 55% (No condensation)
Approvals
TCO ’03(ProLite H2010-W),TCO ’99(ProLite H2010-B), CE, TÜV-GS,
MPR3(prEN50279) / ISO 13406-2, FCC-B, UL, CSA, VCCI-B
NOTE
* Condition: USB peripherals, optional speakers or audio equipment are not connected.
APPENDIX A 27
Model Name
LCD Panel Driving system
Size
ProLite H1900
a-Si TFT Active Matrix
Diagonal: 48cm / 19.0"
0.294mm H × 0.294mm V
300cd/m2 (Typical)
Pixel pitch
Brightness
Contrast ratio
1000 : 1 (Typical)
Viewable angle Right / Left / Up / Down: 89 degrees each (Typical)
Response time 12ms (Black, white, black), 8ms (Gray, Gray)
Display Colors
Approx. 16.77 million
Sync Frequency
Analog: Horizontal 24.0-82.0kHz, Vertical 56.0-85.0Hz
Digital: Horizontal 31.0-82.0kHz, Vertical 50.0-85.0Hz
Dot Clock
Analog: 135MHz maximum Digital: 162MHz maximum
Analog: 1280 × 1024 maximum, 2 MegaPixels
Digital: 1600 × 1200 maximum, 2 MegaPixels
Maximum Resolution
Input Connector
Output Connector
Plug & Play
Dual DVI-I 29pin
D-SUB mini15pin
VESA DDC2BTM , DDC-CI
Input Sync Signal
Separate sync: TTL, Positive or Negative
Composite sync: TTL, Positive or Negative
Sync on green: 0.3Vp-p, Negative
Analog: 0.7Vp-p (Standard), 75W, Positive
Input Video Signal
Digital: DVI (Digital Visual Interface standard Rev.1.0) compliance
Output Video Signal
Analog: 0.7Vp-p (Standard), 75W, Positive
Maximum Screen Size
376.3mm W × 301.1mm H / 14.8" W × 11.9" H
USB Standard
Connectors
Rev. 2.0 / 1.1 compliance
Upstream: Series B, Downstream: Series A
Self-powered Hi-speed hub
Number of USB Ports
Power Source
1 Upstream (For computer), 4 Downstream (For peripherals)
100-230VAC, 50 / 60Hz, 0.69-0.32A
Power Consumption
63W maximum, Power management mode: 4W maximum*
Dimensions
Net Weight
430.0 × 414.5-524.5 × 241.0mm / 16.9 × 16.3-20.6 × 9.5" (W×H×D)
9.0kg / 19.8lbs
Tilt Angle
Right / Left: 35 degrees each, Up: 35 degrees
Environmental
Considerations
Operative temperature:
Storage temperature:
5 to 35°C / 41 to 95°F
-20 to 60°C / -4 to 140°F
Humidity (-20 to under 50°C / -4 to under 122°F) :
20 to 85% (No condensation)
Humidity (50 to 60°C / 122 to 140°F) : 20 to 55% (No condensation)
Approvals
TCO ’03(ProLite H1900-W),TCO ’99(ProLite H1900-B), CE, TÜV-GS,
MPR3(prEN50279) / ISO 13406-2, FCC-B, UL, CSA, VCCI-B
NOTE
* Condition: USB peripherals, optional speakers or audio equipment are not connected.
28 APPENDIX A
DIMENSIONS
ꢀ ProLite H2130
466.0mm/18.3"
436.0mm/17.2"
79.5mm/3.1"
344.0mm/13.5"
(
): Maximum adjustment range
ꢀ ProLite H2010
466.0mm/18.3"
410.5mm/16.2"
77.0mm/3.0"
344.0mm/13.5"
(
): Maximum adjustment range
ꢀ ProLite H1900
430.0mm/16.9"
380.0mm/15.0"
75.5mm/2.9"
344.0mm/13.5"
(
): Maximum adjustment range
APPENDIX A 29
COMPLIANT TIMING
Horizontal
Frequency
31.469kHz
37.861kHz
37.500kHz
35.156kHz
37.879kHz
48.077kHz
46.875kHz
48.363kHz
56.476kHz
60.023kHz
63.981kHz
79.976kHz
75.000kHz
31.469kHz
35.000kHz
49.725kHz
60.150kHz
24.827kHz
61.846kHz
Vertical
Frequency
59.940Hz
72.809Hz
75.000Hz
56.250Hz
60.317Hz
72.188Hz
75.000Hz
60.004Hz
70.069Hz
75.029Hz
60.020Hz
75.025Hz
60.000Hz
70.087Hz
66.667Hz
74.500Hz
74.720Hz
56.424Hz
66.004Hz
Video Mode
Dot Clock
25.175MHz
31.500MHz
31.500MHz
36.000MHz
40.000MHz
50.000MHz
49.500MHz
65.000MHz
75.000MHz
78.750MHz
108.000MHz
135.000MHz
162.000MHz
28.322MHz
30.240MHz
57.283MHz
80.000MHz
21.053MHz
94.500MHz
VGA
640 × 480
SVGA 800 × 600
XGA 1024 × 768
VESA
SXGA
UXGA
1280 × 1024
1600 × 1200
720 × 400
640 × 480
832 × 624
1024 × 768
640 × 400
1152 × 900
VGA TEXT
Macintosh
*
*
*
*
*
*
PC9801
SUN66
NOTE
* Not compliant to DVI input.
30 APPENDIX A
CONNECTOR PIN ASSIGNMENT
ꢀ DVI-I 29pin Connector
Pin
1
Input Signal
T.M.D.S Data 2–
Pin
16
17
Input Signal
Hot Plug Detect
T.M.D.S Data 0–
C2
C4
C1
C3
1
9
8
16
24
T.M.D.S Data 2+
2
17
3
18 T.M.D.S Data 0+
19 T.M.D.S Data 0/5 Ground
20 NC
T.M.D.S Data 2/4 Ground
C5
DVI-I
4
NC
NC
5
6
Clock line (SCL) *
21 NC
7
Data line (SDA) *
Analog V-Sync
22 T.M.D.S Clock Ground
T.M.D.S Clock +
T.M.D.S Clock –
8
23
24
9
T.M.D.S Data 1–
T.M.D.S Data 1+
10
11
12
13
14
15
C1 Analog Red
T.M.D.S Data 1/3 Ground
C2 Analog Green
NC
Analog Blue
C3
C4 Analog H-Sync
NC
Analog Ground
C5
+5V Power
Ground
* Compliant to VESA DDC.
ꢀ D-SUB mini 15pin
Pin
1
Input Signal
Red video
Pin
9
Input Signal
NC
Connector
2
10 Ground
11
Green video
Blue video
Ground
3
4
12 NC
NC
5
13 H-Sync
NC
6
Red video ground
Green video ground
Blue video ground
V-Sync
NC
14
15
7
8
APPENDIX A 31
APPENDIX B
Optional Video Input
This OSD Menu is available only when the optional video adapter is installed in the monitor.
Video input is not switched automatically from Analog or Digital input. Switch to video input by “Signal
Select” on the OSD Menu or the Input Button. Under the power management mode, “Signal Select”
page is displayed immediately by pressing the Menu Button when the Menu is not displayed.
Direct
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
ꢁ Brightness: Press the Brightness Button when the Menu is not displayed.
ꢁ Contrast:
Press the Contrast Button when the Menu is not displayed.
ꢁ Signal Select: Press the Input Button when the Menu is not displayed.
ꢁ Picture Lock: Press the Auto Button when the Menu is not displayed.
For ProLite H2130
ꢁ Volume:
Press the Menu Button within 5 seconds after pressing the Brightness Button or
the Contrast Button during the direct adjustments above.
NOTE
SWITCHING BRIGHTNESS / CONTRAST / VOLUME ADJUSTMENT
(The VOLUME adjustment is for ProLite H2130 only.)
ꢀ
To switch between Brightness, Contrast and Volume adjustments, press the Menu
Button within 5 seconds after pressing the Brightness Button or the Contrast Button
during the direct adjustments above.
Brightness
Contrast
Volume
ꢀ
SIGNAL SELECT (INPUT1 / INPUT2 / S VIDEO / VIDEO)
Select INPUT1, INPUT2, S VIDEO or VIDEO for the signal input when two or more signal
inputs are connected to a signal source.
In case of selecting “Auto” in the adjustment item: Auto Search,
press the Input Button and then the Menu Button. Select INPUT1, INPUT2, S VIDEO or
VIDEO for the signal input so that the input signal (INPUT1 Analog / INPUT1 Digital /
INPUT2Analog / INPUT2 Digital / S VIDEO / VIDEO) is automatically detected.
In case of selecting “Manual” in the adjustment item: Auto Search,
press the Input Button and then the Menu Button. Select the input signal (INPUT1 Analog
/ INPUT1 Digital / INPUT2Analog / INPUT2 Digital / S VIDEO / VIDEO) by pressing the + / –
Buttons.
ꢀ
PICTURE LOCK
“Frame Locked.” is displayed and picture on the screen is locked when pressing the
Auto Button while the Menu is not displayed.
Press the Auto Button again to unlock.
32 APPENDIX B
Menu : Picture Control
(Video)
Picture Control
'Screen OSD... Function Info...
SELECT MENU
-
+
Adjustment Item
Problem / Option
Button to Press
Brightness *
Too dark
Direct
Too bright
Contrast
Too dull
Direct
Too intense
9300K Bluish white (9300K)
Color Temp. / Matrix
6500K Reddish white (6500K)
R (Red)
Too weak
User
G (Green)
B (Blue)
Too strong
NOTE
ꢀ sRGB is an international
standard which defines and
unifies the difference of
color appearance between
equipment.
ꢀ You can not adjust the
Brightness, Contrast and
GammainsRGBmodebecause
those settings are locked.
Y (Yellow)
M (Magenta)
Too light
Too deep
Matrix
C (Cyan)
sRGB
CAL
sRGB mode
Calibration mode: Color appearance is set to the range
adjusted by an optional calibration sensor.
Normal Normal
Gamma
Hi.Cont High contrast
Dark
User
Dark
Gamma: approx.1.8, 2.0, 2.2 or 2.4 is selected.
Too soft
Sharpness
Too sharp
Back-light is too dark
Back-light is too bright
Economy Mode
User
Mode 1 Brightness of back-light is reduced by Approx.10%.
Mode 2 Brightness of back-light is reduced by Approx.50%.
Return to Menu
Highlight “Menu : Picture Control” again.
*
Adjust the User of Economy Mode when you are using the monitor in a dark room and feel the
screen is too bright.
See page 32 for Direct adjustment.
Direct
APPENDIX B 33
Menu : Screen Control
(Video)
Picture
Screen Control
OSD... Function Info...
SELECT MENU
-
+
Adjustment Item
Color System
Problem / Option
Button to Press
Switch the broadcast system automatically. Select
this in normal use.
AUTO
NTSC
PAL
Switch the broadcast system to NTSC by force.
Switch the broadcast system to PAL by force.
Switch the broadcast system to SECAM by force.
SECAM
Color
Too weak
Too strong
Hue
Purplish
Greenish
Return to Menu
Highlight “Menu : Screen Control” again.
34 APPENDIX B
Menu : OSD & Others
(Video)
Picture Screen... OSD & Others
Function Info...
RESET
SELECT MENU
-
+
Problem / Option
1 2 3 4 5
Button to Press
Adjustment Item
OSD Position
You can move the OSD display
area to any one of the following 5
positions within the overall display:
Press the + Button to move the OSD in numerical order. Press
the – Button to move the OSD in reverse numerical order.
OSD Off Timer
OSD Rotation
You can set the OSD display duration
time between 3 and 60 seconds.
OFF
ON
Return to Normal.
Menu screen is rotated 90 degrees in
counterclockwise.
Use this function when using the monitor with portrait orientation.
NOTE
NOTE
OFF
ON
Return to Menu.
All adjustment items are locked out.
Key Lock Mode
To cancel the Key Lock Mode, keep pressing the Menu, + and – Buttons at the same time
for 8 seconds or more.
English
English
Svenska
Swedish
Russian
Chinese
Japanese
Polish
Language
Deutsch
German
Nederlands Dutch
Français
Italiano
French
Italian
Polski
Español
Spanish
NO
Return to Menu.
Reset
RESET
YES
Factory-preset data is restored.
Return to Menu
Highlight “Menu : OSD & Others” again.
APPENDIX B 35
Menu : Functions
(Video)
Picture Screen... OSD...
Functions
Info...
A B C
ABC
A B C
H
SELECT MENU
-
+
Problem / Option
Button to Press
Adjustment Item
Auto Search
Search the input signal automatically in the following rotation:
INPUT1Analog INPUT1 Digital INPUT2Analog
Auto
Video
S Video
INPUT2 Digital
Manual
INPUT1
Select the input signal by “Signal Select” function.
Select the Analog input.
Select the Digital input.
Signal Select
Direct
Select the Analog input.
Select the Digital input.
INPUT2
S Video
Video
1 to 1
Aspect
Full
Select the S Video input.
Select the Video input.
Displayed at the same magnification
Expansion display of Aspect
Expansion display
Full Screen
Zoom
Zoom In
Zoom in the image.
Zoom Out Zoom out the image.
To move the zoom point to the right.
H-Position
V-Position
User
To move the zoom point to the left.
To move the zoom point downward.
To move the zoom point upward.
1
3
2
4
4 Multi.
For 4 split screen display by 4 monitors
NOTE
To cancel the “User” settings, press the Auto Button when the setting screen is displayed.
A B C
Flipping
OFF
Mirror
Return to Normal.
Mirror reversed image is displayed.
ABC
A B C
180°
OFF
The image rotated 180 degrees is displayed.
LED is turned OFF.
LED ON/OFF*
H
ON
LED is turned ON.
Return to Menu
Highlight “Menu : Functions” again.
* Turn OFF the LED when you are bothered by the light in multiple screen environment.
See page 32 for Direct adjustment.
Direct
36 APPENDIX B
Menu : Information
(Video)
Picture Screen... OSD... Function
Information
Model Name
Input Signal
:
:
ProLite H2130
Video
Signal Timing
:
:
NTSC
1:00
Operating Time
-
+
Model Name, Input Signal, Signal
Timming and Operating Time are
displayed.
APPENDIX B 37
POWER MANAGEMENT FEATURE
The monitor can provide the POWER MANAGEMENT feature while the video input is available by
using the video adapter.
When the signal from the video equipment is off, the monitor enters into Power Management Mode
which reduces the power consumption to less than 4W and the power indicator turns to orange.
From Power Management Mode, the image reappears in several seconds when the signal is input
from the video equipment.
Specifications for Optional Video Input
Input Connector
RCA pin jack
S-Video terminal
Input Video Signal
Video*: NTSC, PAL, SECAM
NOTE
* Not all broadcast systems are supported.
APPENDIX B 38
|