Extron electronic Extron Electronics Cable Box SDI AVR 100 User Manual

User’s Guide  
HDSDI-ACR 100  
SDI-AVR 100  
High Definition SDI to Component Video/RGB Converter  
SDI to Video/RGB Converter  
68-553-01 C  
Printed in the USA  
02 02  
Installation  
RGB/Component (HDSDI-ACR 100) or RGB/YUV (SDI-  
AVR 100) switch — Set this switch to the Off position to  
output RGB video. Set the switch on for component video.  
IN  
R/R-Y  
G/Y  
V
B/B-Y  
COMPOSITE  
OUTPUT  
S-VIDEO  
OUTPUT  
5
OUT  
H
S
ON  
ON  
OFF  
OFF  
100-240V  
50/60 Hz 0.2A  
SDI INPUT  
OUTPUTS  
Bi/tri-level switch (HDSDI-ACR 100 only) — Set this  
switch to the On position to output tri-level sync on the  
component video output. Set the switch off for bi-level  
sync.  
6
1
2
7
3
4
ON  
Figure 4 — SDI-AVR 100 rear panel  
OFF  
Composite Output connector (SDI-AVR 100 only) — Connect a  
composite video display device to this BNC connector. This  
3
HDSDI-ACR 100 switch configuration  
RGB/  
Component  
output is available whenever an active SDI signal is applied to the  
Output video format  
RGBHV/RGBS  
SOG  
Off  
Bi/tri-level  
Either  
Either  
Off  
1
SDI input connector,  
.
Off  
Off  
On  
On  
RGsB  
On  
S-video Output connector (SDI-AVR 100 only) — Connect an  
S-video device to this 4-pin mini DIN connector. This output is  
4
Y, R-Y, B-Y w/ bi-level on Y  
Y, R-Y, B-Y w/ tri-level on Y  
Either  
Either  
On  
available whenever an active SDI signal is applied to the SDI  
1
input connector,  
.
SDI-AVR 100 switch configuration  
Output video format  
RGBHV/RGBS  
RGsB  
SOG RGB/YUV  
RGB/component video output connectors  
5
Off  
On  
Off  
Off  
On  
Ensure that the rear panel DIP switches are in the correct  
configuration (see Rear Panel Controls).  
Y, R-Y, B-Y  
Either  
R/R-Y  
G/Y  
B/B-Y  
RGBHV video connection —  
Connect to five BNC connectors  
as shown.  
Set Up switch (SDI-AVR 100 only) — Set this switch to the On position  
to output an NTSC signal that is on the 7.5 IRE pedestal. Set the  
switch off to return the signal to the normal level.  
RGBHV  
Video  
H
V
S
RGBS video connection —  
Connect to four BNC connectors  
as shown.  
Beta switch (SDI-AVR 100 only) — Set this switch to the On position to  
set the color level of the YUV output to the Betacam level. Set the  
switch off to restore the YUV output to the normal level. If a  
Betacam signal is input, the switch should be set to On to output  
the Betacam format. Otherwise, the output will be NTSC or PAL.  
R/R-Y  
G/Y  
V
B/B-Y  
RGsB and component video  
connection — Connect to three  
BNC connectors as shown.  
RGBS  
Video  
H
S
Color Bars switch (SDI-AVR 100 only) — Set this switch to the On  
position to output NTSC or PAL color bars. Set the switch off for  
the converted video input.  
AC power connector — Plug a  
standard IEC power cord into  
this connector to connect the  
converter to a 100 to 240VAC, 50  
Hz or 60 Hz power source.  
6
R/R-Y  
G/Y  
V
B/B-Y  
NTSC/PAL switch (SDI-AVR 100 only) Used in conjunction with  
the Color Bars switch only, set this switch to the On position to  
output PAL color bars. Set the switch off for NTSC color bars.  
RGsB or  
Component  
Video  
H
S
Front Panel Indicators  
Rear Panel Controls  
All indicators are on the front panel. Figure 5 and figure 6 show  
HDSDI-ACR 100 and SDI-AVR 100 indicators.  
DIP switches  
7
Power LED — The Power LED indicates that power is on.  
1
2
SOG switch — Set this switch to the On position to output sync-  
on-green for RGB video (RGsB). Set the switch off for  
RGBHV or RGBS video.  
720P LED (HDSDI-ACR 100 only) — The 720P LED indicates that  
the converter is outputting the HDTV 720P video format.  
4
HDSDI-ACR 100 and SDI-AVR 100 • Installation  
HDSDI-ACR 100 and SDI-AVR 100 • Installation and Operation  
5
Indicators and Specifications  
The equalization applied to the SDI-AVR 100’s input signal is  
sufficient for an input coaxial cable length of at least 1000 feet (305  
meters) of Extron SHR cable or Belden 8281 cable.  
FORMAT  
720P  
1080I  
1080P  
HDSDI-ACR 100  
HDSDI TO VIDEO/RGB CONVERTER  
The equalization applied to the HDSDI-ACR 100’s input signal is  
sufficient for an input coaxial cable length of at least 330 feet (100  
meters) of Extron SHR cable or Belden 8281 cable.  
1
2
3
4
Figure 5 — HDSDI-ACR 100 front panel  
Minimum/maximum levels ...... 0.5V to 1.0V p-p with no offset  
Impedance .................................... 75 ohms  
Return loss .................................... >-15dB @ 0 MHz to 270 MHz  
Maximum DC offset .................... 0.5V  
LOCK  
SDI-AVR 100  
SDI TO VIDEO/RGB CONVERTER  
Video processing  
Encoder ......................................... 10 bit digital  
1
5
Frequency response ..................... Luminance ................ 0 to 5.75 MHz, 0.5dB  
Chroma .................... 0 to 2.75 MHz, 0.5dB  
Figure 6 — SDI-AVR 100 front panel  
S/N ................................................ >70dB  
RGB matrix error ......................... <1%  
1080I LED (HDSDI-ACR 100 only) — The 1080I LED indicates  
that the converter is outputting the HDTV 1080I video format.  
3
4
5
1080P LED (HDSDI-ACR 100 only) — The 1080P LED indicates  
that the converter is outputting the HDTV 1080P video format.  
Video signal characteristics — for color bar output on the  
SDI-AVR 100 only  
Dot clock ....................................... 27 MHz  
Lock LED (SDI-AVR 100 only) — The Lock LED indicates that  
the converter is locked to the 270 Mbs input signal.  
Pixel clock accuracy ..................... 30 ppm  
Specifications  
Video output  
Number/signal type  
Video  
SDI-AVR 100 .................... 1 composite video and 1 S-video, and  
1 analog RGBHV/RGBS/RGsB or component  
video (Y, R-Y, B-Y) (switch selectable)  
Differential phase error .............. SDI-AVR 100 ............ <1º  
Differential gain error ................. SDI-AVR 100 ............ <1%  
HDSDI-ACR 100 .............. 1 analog RGBHV/RGBS/RGsB or component  
video (Y, R-Y, B-Y) (switch selectable)  
Connectors  
Video input and loop-through  
Number/signal type  
SDI-AVR 100 .................... 1 SDI (4:2:2, SMPTE 259M-C)  
HDSDI-ACR 100 .............. 1 HDSDI (SMPTE 292M)  
Connectors  
SDI-AVR 100 .................... 1 female BNC (composite video)  
1 female 4-pin mini DIN (S-video)  
6 female BNC (RGB, component video, or S-video)  
HDSDI-ACR 100 .............. 6 female BNC  
SDI-AVR 100 .................... 1 female BNC (SDI input)  
Levels ............................................. Composite video ...... 1V p-p (nominal)  
S-video .................... 1V p-p/luma, 0.3V p-p/  
chroma (nominal)  
1 female BNC (SDI reclocked loop-through)  
HDSDI-ACR 100 .............. 1 female BNC (HDSDI input)  
1 female BNC (HDSDI reclocked loop-through)  
RGB  
.................... 0.7V (nominal)  
Component video .... Y = 1V p-p; R-Y, B-Y = 1V  
p-p (nominal)  
Levels depend on the format selected (NTSC, PAL, Betacam).  
6
HDSDI-ACR 100 and SDI-AVR 100 • Specifications  
HDSDI-ACR 100 and SDI-AVR 100 • Specifications  
7
Impedance .................................... 75 ohms  
Return loss .................................... -30dB @ 5 MHz  
Sync  
Output type .................................. RGBHV, RGBS, RGsB  
Standards (SDI-AVR 100 only) .. NTSC 3.58, PAL 4.43, Betacam  
Output impedance....................... 75 ohms  
Max. rise/fall time....................... 200 nS  
Polarity .......................................... SDI-AVR 100 ............ negative  
HDSDI-ACR 100 ...... bi-level or tri-level sync  
(switch selectable) on luma  
(Y) leg  
General  
Power............................................. 100VAC to 240VAC, 50/60 Hz, internal, auto-  
switchable  
SDI AVR 100 ..................... 6 watts  
HDSDI AVR 100 .............. 10 watts  
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) / 10% to  
90%, non-condensing  
Operating +32° to +122°F (0° to +50°C) / 10% to  
90%, non-condensing  
Rack mount................................... Yes, with optional rack shelf, part #60-190-01  
Enclosure type .............................. Metal  
Enclosure dimensions ................. 1.75" H x 8.75" W x 8.0" D  
(1 rack unit high, half-rack unit wide)  
4.5 cm H x 22.2 cm W x 20.3 cm D  
(Depth excludes connectors.)  
Shipping weight .......................... 4 lbs (1.8 kg)  
Product weight  
SDI-AVR 100 .................... 1.8 lbs (0.8 kg)  
HDSDI-ACR 100 .............. 1.9 lbs (0.9 kg)  
Vibration ....................................... ISTA/NSTA 1A in carton (International Safe  
Transit Association)  
Listings .......................................... UL, CUL  
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES  
MTBF ............................................. 30,000 hours  
Warranty ....................................... 3 years parts and labor  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
USA  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort  
The Netherlands  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Building  
Singapore 368363  
Extron Electronics, Japan  
Daisan DMJ Building 6F  
3-9-1 Kudan Minami  
Chiyoda-ku, Tokyo 102-0074 Japan  
+81.3.3511.7655  
714.491.1500  
+31.33.453.4040  
+65.6383.4400  
Fax 714.491.1517  
Fax +31.33.453.4050  
Fax +65.6383.4664  
Fax +81.3.3511.7656  
© 2002 Extron Electronics. All rights reserved.  

Apollo Car Stereo System 15SL15 User Manual
Atlantic WINDOWPANE 240 DVD User Manual
Audiovox AVD300T User Manual
Bogen Imaging Inc Car Speaker AMBSL 1 User Manual
Canon Camcorder GL1 User Manual
Canon xhg1 User Manual
Casio FX 912MS User Manual
Clarion Car Video System NZ503 User Manual
Hasselblad H4D 50MS User Manual
JVC GR AX857UM User Manual