Elmo TSE270X User Manual

·
·
TSE270X TSE271X TSE272X  
INSTRUCTION MANUAL  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.  
DO NOT REMOVE COVER (OR BACK).  
NO USER SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The lightning flash with arrowhead symbol, within  
an equilateral triangle, is intended to alert the user  
to the presence of uninsulated "dangerous  
voltage" within the product's enclosure that may  
be of sufficient magnitude to constitute a risk of  
electric shock to persons.  
The CAUTION label, shown on the left, is attached  
on the top of camera.  
INFORMATION  
This equipment has been tested and found to comply  
with the limits for Class A digital device, pursuant  
to Part 15 of the FCC Rules.These limits are  
desinged to provide reasonable protection against  
harmful interference when the equipment is operated  
in a commercial environment.This equipment generates,  
uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the  
instruction manual, may cause harmful interference  
to radio communications. Operation of this equipment  
in a residential area is likely to cause harmful  
interference in which case the user will be required  
to correct the interference at his own expense.  
The exclamation point within an equilateral  
triangle is intended to alert the user to the  
presence of important operating and maintenance  
(servicing) instructions in the literature  
accompanying the appliance.  
CAUTION  
Do not use any power supply other than specified.  
WARNING  
USER-INSTALLER CAUTION:Your authority to operate  
this FCC verified equipment could be voided if  
you make changes or modifications not expressly  
approved by the party responsible for compliance  
to Part of the FCC Rules.  
TO REDUCE THE RISK OF FIRE OR  
ELECTRIC SHOCK, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
PRECAUTIONS FOR USE AND INSTALLATION  
* Install your camera where no video noise appears.  
When camera cables have been laid near electric wires or  
television receivers, a noise may interfere the image.  
If noise occurs, relocate cables or reinstall equipment.  
* Check the ambient temperature and humidity.  
Avoid using camera in areas where temperature is  
consistently hotter or colder than the specified range (See  
Specifications chart below) or poor image quality or  
damaged parts may occur.  
* Never aim the camera at the sun.  
Never aim or point the camera at the sun even if you are  
not shooting.  
* Do not shoot intense light.  
Strong light such as a spot light on the image plane will  
cause blooming or smear. When strong light comes into  
the image plane, vertical stripes may appear on it.  
However, this does not mean that the camera is defect.  
* Take precautions when handling a camera.  
Do not drop your camera, or give it a strong shook or  
vibration. This may cause camera to malfunction.  
* Do not touch internal parts.  
Precautions should also be taken to avoid areas of high  
humidity.  
* Should you notice any trouble.  
Be sure not to touch the internal parts. This may cause to  
electrical shock.  
If any trouble occurs while you are using the camera, turn  
off the camera and contact your dealer. Failure to do so may  
cause damage to the camera.  
* Do not let the camera get wet.  
Install the camera at the place where it will not get wet.  
Should it gets wet, turn off the power immediately and  
contact your dealer.  
* The socket-outlet should be installed near the equipment  
and should be easily accessible.  
SPECIFICATION  
Model  
TSE270X  
AC24V 10% 60Hz 1Hz  
Approx.6W  
TSE271X  
DC12V (DC11V-16V)  
Approx.3.2W  
TSE272X  
AC120V 10% 60Hz 1Hz  
Approx.6W  
Power source  
Power consumption  
Pick-up device  
Effective picture element  
Scanning area  
1/3" Black & White interline-transfer CCD  
512 (H) X 492 (V)  
4.92mm (H) X 3.69mm (V)  
2:1 interlaced  
Scanning system  
Scanning frequency(H)(V)  
Sync. system  
15.75Hz 60Hz  
Line-lock  
15.75Hz 60Hz  
Line-lock  
15.734Hz 59.94Hz  
Internal  
Resolution  
380TV lines (Horizontal) 350TV lines (Vertical)  
More than 46dB  
S/N ratio  
Recommended illumination  
AGC  
22 lx (F1.2 under incandescent lamp)  
Built into camera circuitry  
Sens-up  
Provided (Factory-set at OFF)  
Provided (Factory-set at OFF)  
Provided (Factory-set at OFF)  
Backlight control  
AES  
(Automatic Electronic Shutter)  
Gamma correction  
Accumulation node  
Output signal  
0.45  
Field  
VBS 1.0 Vp-p, 75, EIA, compatible  
Auto-iris terminal  
Power terminal  
Lens mount  
4P (DC/Video)  
Power cord  
3P terminal  
2P terminal  
CS  
Ambient temperature  
Ambient humidity  
Dimensions  
-10°C ~ +50°C (14°F~122°F)  
30% ~ 90%  
60(W) X 60(H) X 120(D)mm (2.4 X 2.4 X 4.9 inches)  
510 grm (1.13 lbs) 320 grm (0.71 lbs)  
600 grm (1.32 lbs)  
Weight  
Note: Weight and dimensions are approximate.  
Design and specifications are subject to change without prior notice.  
- 2 -  
PART NAMES AND FUNCTIONS  
2
4
1
3
10  
2
1 Lens mount  
Mount a CS-mount lens.  
2 Camera mount  
For mounting a camera on wall, housing, etc.  
(1/4"-20UNC thread)  
MODEL TSE270X  
MODEL TSE271X  
MODEL TSE272X  
3 Focusing dial  
For fine-adjustment of the lens back-focus.  
4 IRIS terminal  
Connect when an automatic iris lens is used.  
5
6
7
5
VIDEO OUT terminal  
Connect to a monitor TV, etc. (BNC connector)  
AC power terminal  
6
7
Connect this to optional AC 24V power supply.  
Ground terminal  
Connect this to the ground wire of the power supply cord.  
5
8
8 DC power terminal  
Connect this to optional DC 12V power supply.  
9 Power cord  
Connect this to AC120V power supply.  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE  
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,  
INTRODUIRE LA LAME LA PLUS LARGE DE LA  
FICHE DANS LA BORNE CORRESPONDANTE  
5
DE LA PRISE ET POUSSER JUSQU' AU FOND.  
Camera control switches  
10  
9
Refer to "CAMERA CONTROLS." on page 6.  
- 3 -  
HOW TO CONNECT  
1. Before connection, make sure that power of all units are OFF and cords are unplugged.  
2. Mount a lens onto the camera. Refer to "HOW TO USE" for usable lens.  
3. Connect video terminal of the camera and the video input terminal of a monitor TV, etc. with a 75coaxial cable.  
4. Connect the power terminal of the camera to a power supply.  
Caution: Installation should be made by a qualified service personnel and should conform to all local codes.  
Lens, coaxial cable for video signal and power supply are not supplied with a camera.  
HOW TO USE  
1. TSE270X: Turn on the unit by connecting the power cord of AC 24V power supply.  
TSE271X: Turn on the unit by connecting the power cord of DC 12V power supply.  
TSE272X: Connect the power cord to AC 120V and turn the power ON.  
2. Adjust the iris and focus of the lens so that optimum image may  
be obtained.  
CS-mount  
*Usable lenses  
Lens  
5mm or less  
CS-mount lenses, whose length "L" (in the illustration) from the  
bearing surface of the mount is 5mm or less if protruded, should  
be used.  
L
*Using the zoom lens (adjustment of the back focus)  
The camera is set at the standard back focus position when  
shipped from factory. Depending on types of zoom lenses,  
Lens  
Camera  
however, slight readjustment may be necessary.  
Adjust the lens back-focus by turning the focusing dial in either  
Focusing dial  
direction as per the illustration, referring to the following  
instructions.  
1
Place an object at any fixed distance and set the focus ring of the zoom lens accordingly.  
2 Set the zoom lens to full TELE position and obtain the best focus position by turning the focus ring or the zoom  
lens.  
3 Set the zoom lens to full WIDE position and obtain the best focus position by turning the focusing dial located on  
the side of the camera.  
4 Repeat procedures  
2
and 3 until focus remains constant throughout the zooming range.  
Note: When weight of the lens is more than 1kg, the camera should be supported by the lens rather than relying  
on camera mounting screw.  
Adjust the back-focus only when necessary.  
*Using an auto iris lens  
When a DC driven type auto iris lens is used, set the AUTO IRIS switch at DC, and connect the plug of the lens  
(for iris terminal) to the IRIS terminal on the right side of the camera.  
When a video feedback type auto iris lens is used, set the AUTO IRIS switch at VIDEO, and connect the plug of  
the lens (for iris terminal) to the IRIS terminal on the right side of the camera.  
(Refer to Lens manual for the level adjustment.)  
IRIS terminal  
DC position  
Control -  
Control +  
VIDEO position  
+9V iris power (50mA Max.)  
GND  
1
2
3
4
Camera  
Plug for IRIS terminal  
(CHUOMUSEN E4-191J-100)  
Auto iris lens  
Drive +  
Drive - (GND)  
0.8Vp-p auto iris video signal  
GND  
Soldering side  
*When a video feedback type auto iris lens (peak/average selectable type) is used at peak mode, BLC may not  
function well. In such a case, select the average mode.  
3. Before your use of the camera at AES (Automatic Electronic Shutter) mode.  
*When using an auto-iris lens, set the AES switch at OFF.  
(The AES switch is set at OFF when shipped from factory.)  
*The AES mode may increase smears on monitors, which is caused by characteristics of CCD and is not defect.  
Set the AES switch at OFF in case smears appear excessively.  
- 4 -  
LINE-LOCK CONTROL (TSE270X/TSE272X)  
Matching the vertical synchronization with the power frequency is called the line-lock.  
When two or more cameras are switched by the video switcher to a monitor TV, the vertical sync. phase can be locked  
with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching.  
Monitor TV  
Video output  
CAMERA  
1
Video  
input  
Video switcher  
Video output  
To AC 24V power supply (TSE270X)  
CAMERA  
2
}
1.The camera is synchronized to the power frequency of 60Hz ±0.5Hz covering a normal fluctuation of the power  
To AC 120V power supply (TSE272X)  
Caution:  
frequency.The camera may not compensate for large fluctuation caused by power generated by an engine  
generator, etc.  
2.It takes about 10 seconds or more to obtain a stable synchronization after the power is turned on. This is  
necessary to stabilize the camera against the power noise.  
- 5 -  
CAMERA CONTROLS  
By adjusting the switches/potentiometers provided on the side panel, the control functions are available.  
1 AES switch  
TSE270X, TSE272X  
[Electronic shutter] The camera is  
factory-set at the AES switch OFF  
and 1/60 sec. shutter speed.  
SENS-UP  
AUTO IRIS  
V-PHASE  
[AES (Automatic Electronic Shutter)]  
By setting the AES switch to ON, the  
Automatic Electronic Shutter mode  
(1/60~1/100,000 sec) is available.  
AES  
ON  
BLC  
ALC  
LEVEL  
DC VIDEO  
Note: In electronic shutter mode;  
*Sufficient brightness is  
required.  
OFF  
*The picture will flicker  
when shooting under the  
illumination produced by  
fluorescent lamp.  
1
2
3
4
5
6
2 SENS-UP switch  
To increase the sensitivity, set this  
switch to ON position.  
TSE271X  
SENS-UP  
AUTO IRIS  
3 BLC (Back Light Control) switch  
In case the back oighting is too  
brighit to shoot the main object  
clearly, set this swith to ON position.  
AES  
ON  
BLC  
ALC  
LEVEL  
DC VIDEO  
OFF  
4 ALC LEVEL  
Adjust video output level, when  
AUTO IRIS switch is DC position.  
1
2
3
4
5
5 AUTO IRIS switch  
When a DC driven type auto iris lens is used, set this switch to DC position.  
When a video feedback type auto iris lens is used, set this switch to VIDEO position.  
Vertical sync. phase adjustment potentiometer  
6
Vertical sync. phase adjusting potentiometer is set at the position fully counterclockwise that the delay time of  
vertical sync. phase against the phase of power frequency is shortest, when shipped from the factory.  
Turning this potentiometer clockwise will make the delay time of vertical sync. Phase against the phase of  
power frequency longer.  
6
camera in combination with other camera(s) controlled by the Line-Lock synchronization.  
Use the function control potentiometer  
if the picture image on a monitor TV may flow when using the  
In this case, get a proper image by shifting the phase of vertical sync. signal of the camera against that of the  
other. If a proper image cannot be obtained even after this adjustment, reset the potentiometer to its original  
6
position, and use the function control potentiometer  
signal of other camera.  
of the other camera to shift the phase of vertical sync.  
Caution: Before making adjustment, make sure that cameras have their power supplies connected with the same  
polarity. (not 180°apart)  
- 6 -  
PROFILE  
All dimensions in mm (inch)  
43 (1.69)  
MODEL TSE270X  
60 (2.36)  
120 (4.72)  
MODEL TSE271X  
43 (1.69)  
MODEL TSE272X  
6-14, Meizen-cho, Mizuho-ku,  
Nagoya, 467-8567 Japan  
ELMO CO., LTD.  
OVERSEAS SUBSIDIARY COMPANIES  
ELMO Mfg. Corp.  
ELMO Canada Mfg. Corp.  
ELMO (Europe) G.m.b.H.  
1478 Old Country Road,  
Plainview, NY 11803-5034  
U.S.A.  
44 West Drive, Brampton,  
Ontario, L6T 3T6,  
Canada  
Neanderstr. 18  
40233 Dusseldorf,  
Germany  
Tel. 516-501-1400  
Fax. 516-501-0429  
Tel. 905-453-7880  
Fax. 905-453-2391  
Tel. 0211-376051-53  
Fax. 0211-376630  
6X1NHVA02 B  
Printed in CHINA  

Alpine Electronics Car Stereo System CDE 100E User Manual
Atlantis Land POCKET USB A01 AU2 User Manual
Baxi Potterton BAXI COMBI INSTANT 80 HE User Manual
Black Decker BDSB34 CL User Manual
Blaupunkt MONTREUX C30 User Manual
Canon 0157W050 User Manual
Canon E 77 User Manual
Canon EF S60MM User Manual
Canon PSC 2000 User Manual
Elta 7537N1 User Manual