XDMA7650
INSTALLATION/OWNER'SꢀMANUAL
AM/FM/CD/MP3/WMAꢀReceiverꢀwithꢀUSB,ꢀ
®
ControlꢀforꢀiPod ꢀandꢀ2-StepꢀMotorizedꢀFace
XDMA7650ꢀINSTALLATIONꢀ
WiringꢀDiagram
Antenna Connector
BLACK
Front Preamp Output
Steering Wheel Interface Input
BLUE
PAC SWI-PS required
Subwoofer Preamp Output
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDMA7650 uses one
10 amp ATM fuse located
beside the wiring connector.
3
XDMA7650ꢀOPERATION
ControlꢀLocationsꢀ-ꢀReceiver
1
2
3
4
5
6
7
8
9
12 11
10
19 18
17 16 15
14
13
20
Open
Audio / Menu
Select / Power
Mute
1
11
12
13
14
15
16
17
Preset 6 / Folder Up
Preset 5 / Folder Down
Preset 4 / Play / Pause
Tune / Track Up
2
3
Loud
4
Preset 1 / Repeat
5
Tune / Track Down
Source
Preset 2 / Random
Preset 3 / Intro
Eject
6
7
18 Display
8
Reset
9
USB Input
19
Band / Escape
Auxiliary Input
10
20
4
XDMA7650ꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
1
2
3
4
5
6
21
7
8
9
20
19
18
17
10
11
12
13
16
15
14
Source
1
2
Loudness
Open
12
13
14
15
16
Volume Up
Audio / Menu
Select / Power
3
Mute
4
Display
EQ
Tune / Track Up
Volume Down
Scan / PS
5
6
17 Preset 5 / Folder Down
18
19 Preset 1 / Repeat
7
Preset 4 / Play / Pause
Preset 2 / Random
Preset 3 / Intro
Preset 6 / Folder Up
Local
8
9
Band / Escape
20
21
10
11
Tune / Track Down
5
XDMA7650ꢀOPERATION
GeneralꢀOperation
PowerꢀOn/Off
Press or any other button (except EJECT or OPEN) to turn
the unit on. Press and hold for 3 seconds to turn the unit
off.
Source
Press SOURCE to select between AM/FM, CD player, USB,
operation of iPod and auxiliary input. Modes of operation are
shown in the display.
NOTE: CD, USB and operation of iPod modes will not appear
unless a CD is inserted or USB/iPod devices are connected.
AuxiliaryꢀInput
Insert a 3.5mm connector into the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc. Press
SOURCE to select AUX mode.
SteeringꢀWheelꢀInterfaceꢀ
Input
The steering wheel interface input located on the back of
the head unit allows connection to the PacificꢀAccessoryꢀ
Corporationꢀ(PAC)ꢀSWI-PS interface module (sold
To configure steering wheel controls, follow the instructions
provided with the PACꢀSWI-PS interface module. After
installing the interface module, insert the module's 3.5mm
jack into the port on the back of the head unit.
Volume
Display
Adjust volume using volume knob (00-46).
Press DISPLAY to select between clock and different types of
information, such as radio frequency, CD track/elapsed time
or MP3/WMA song information.
Reset
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located on the front panel.
SetꢀtheꢀClock
With the unit on, press and hold DISPLAY until the clock
begins to flash, then release. Press TUNE
to adjust the
nn
hours and TUNEꢀ
to adjust the minutes. Press DISPLAY
ll
momentarily to save the selected time.
12/24-hourꢀClockꢀ
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10 00). In European frequency spacing
:
mode, the clock will display 24-hour time (22:00).
6
XDMA7650ꢀOPERATION
GeneralꢀOperationꢀ-ꢀSetupꢀMenu
SetupꢀMenu Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. Press AUDIO/MENU momentarily
to select between the menu functions and rotate the volumeꢀ
knob left/right to adjust or activate the desired function.
MenuꢀFunction
Options
Action
AutoꢀStationꢀ
Store
Press SELECT to seek and save 6 strong stations in the
current band. (Tunerꢀmodeꢀonly)
AUTO STORE
LOCAL OFF
LOCAL ON
Activates distance tuning (in Tuner mode only).
Local/Distanceꢀ
Tuning
Activates local tuning for strong station reception only.
Programs the unit to USA tuner spacing.
FREQ USA
FREQ EUR
CLOCK OFF
Tuner
Frequency
Spacing
(200kHz for FM and 10kHz for AM). (Tunerꢀmodeꢀonly)
Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM). (Tunerꢀmodeꢀonly)
Programs unit to not display the clock when the power is
off.
Clockꢀ
Display
CLOCK ON
AUX-IN ON
Programs unit to display the clock when the power is off.
Enables the front panel 3.5mm auxiliary input.
Auxiliaryꢀ
Input
AUX-IN OFF Disables the auxiliary input.
Activates the subwoofer RCA output. Subwoofer control
will be available in the audio menu.
SUBWFR OFF Disables the subwoofer RCA output.
SUBWFR ON
Subwoofer
RCAꢀoutput
BEEP OFF
BEEP ON
Disables the confirmation beep.
Enables the confirmation beep.
Beepꢀ
Confirmation
Programs unit to always turn on at a specific volume
(default is OFF). Any volume level 1-46 can be selected.
Programmableꢀ
TurnꢀOnꢀVolume
PRO-VOL #
MESSAGE OFF Disables power on message. (example: GOOD MORNING)
MESSAGE ON Enables power on message to be displayed.
Powerꢀonꢀ
Message
SCROLL 15
SEC
Programs unit to scroll information once every 15
seconds (default).
Programs unit to scroll once, then show first 10
characters on display.
SCROLL ONCE
Scrollingꢀ
Option
SCROLL ON Programs unit to scroll continuously.
Programs unit to show the first 10 characters on the
display.
SCROLL OFF
DIMMER HIGH Programs unit to the brightest illumination level.
DIMMER MED Programs unit to the middle illumination level.
DIMMER LOW Programs unit to the dimmest illumination level.
Illuminationꢀ
Dimmer
DEMO OFF
DEMO ON
Disables the demonstration mode.
Enables the demonstration message.
Demonstrationꢀ
Mode
7
XDMA7650ꢀOPERATION
GeneralꢀOperation
Audio Press AUDIO momentarily to select between Bass, Treble,
Balance, Fader, EQ, Subwoofer and Source Volume Level.
BASS
TREBLE
BALANCE
FADER
EQ
SUBWOOFER*
SOURCE LEVEL
Bass Press AUDIO until BASS appears then rotate volume knob
left/right to adjust ( -6 minimum / +6 maximum).
Treble Press AUDIO until TREBLE appears then rotate volume knob
left/right to adjust ( -6 minimum / +6 maximum).
Balance Press AUDIO until BAL appears then rotate volume knob
left/right to adjust (BAL LEFT 12 - BAL RIGHT 12).
BAL EVEN represents equal balance
Fader Press AUDIO until FADER appears then rotate volume knob
left/right to adjust (FADER FRONT 12 - FADER REAR 12).
FAD EVEN represents equal fader
EQ Press AUDIO until EQ appears. Rotate the volume knob left/
right to select between FLAT (default), POP, JAZZ, CLASSIC,
BEAT, ROCK and USER equalization curves. Press SELECT
to confirm. Any manual adjustment to the Bass or Treble
settings are automatically saved as USER.
Subwoofer Press AUDIO until SUB appears then rotate volume knob
left/right to adjust (0 minimum / +12 maximum).
*ꢀNote:ꢀSubwoofer option will not appear if disabled in the
setup menu. Refer to page 7 for details.
SourceꢀVolumeꢀLevel The source volume level control allows a gain adjustment
for each audio source: AM, FM, CD, AUX, USB and operation
of iPod. Set the source volume level for each mode,
depending on the relative volume of each audio source.
To set the source volume level, press AUDIO until SRC
LEVEL appears. After one second, the current mode will
appear on the display. Turn the volume knob to adjust
the audio level of the current source (-6 minimum/+6
maximum).
Note:ꢀOnly the current mode will be available for
adjustment. To adjust another mode of operation, press
SOURCE until the desired mode is selected, then set the
source volume level for that mode.
8
XDMA7650ꢀOPERATION
AM/FMꢀTunerꢀOperation
Press TUNE
or TUNEꢀ
for more than one second
nn
ll
SeekꢀTuning
to seek to the next strong station.
Press TUNE or TUNEꢀ
radio frequency up or down one step at a time. Press and
hold to advance quickly.
momentarily to change
nn
ll
ManualꢀTuning
Press BAND to select between FM1, FM2, FM3, AM1 and
Bandꢀ
AM2 bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
StoringꢀandꢀRecallingꢀ
StationꢀPresets
9
XDMA7650ꢀOPERATION
CDꢀPlayerꢀOperation
InsertꢀCD Press EJECT to access the CD slot. With the label facing
up, insert a standard size CD into the CD slot. The CD will
automatically begin playback.
EjectꢀCD Press EJECT to eject the CD. The unit will change to
previous mode of operation. If the disc is not removed
within 10 seconds, the unit will reload the disc. The unit
does not have to be turned on to eject CD.
TrackꢀSelect
Press TRACKꢀ
to skip to the beginning of the next
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
FastꢀForwardꢀandꢀReverse
Press and hold TRACKꢀ
or reverse a track.
or TRACK
to fast forward
ll
nn
Pause
Intro
Press
Press
/
/
II to temporarily stop CD playback.
l
II again to resume playback.
l
Press INTꢀto enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays the first 10 seconds of each track.
Repeat
Random
Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• OFF - Plays all tracks on CD.
• TRACK - Continuously repeats selected track.
Press RDMꢀto enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
CD-R/CD-RWꢀCompatibility
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
10
XDMA7650ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
PlayingꢀanꢀMP3/WMAꢀDisc When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
DisplayingꢀInformation Press DISPLAY to select between title (default), artist, file
name, folder name, track number, and clock/elapsed time.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
ꢀꢀ
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
TitleꢀIconꢀ
ArtistꢀIconꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
FolderꢀIconꢀ
This icon will illuminate when the directory name is
displayed.
FileꢀIconꢀ
ꢀ
This icon will illuminate when the file name is displayed.
CharacterꢀSupport Maximum character display information
• Track name – 32 character maximum
• Directory name – 32 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
*Song title and Artist Name will only be displayed if included
with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
XDMA7650ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
Folder/FileꢀSearchꢀMode
MP3/WMA CD mode features a file and folder search mode.
This search allows navigating through folders to find a
specific MP3 or WMA file for playback.
Stepꢀ1
Stepꢀ2
PressꢀSELECT. "MP3 CD SEARCH" will appear, then a
list of the files in the currently selected directory will be
accessible.
Turnꢀtheꢀvolumeꢀknob. The list of subfolders and files in the
current folder will cycle. Turning the volume knob left will
cycle to the beginning of the folder/file list. Any subfolders
will be listed at the beginning of the list, followed by any
files.
will illuminate when a folder is highlighted.
will illuminate when a file is highlighted.
Stepꢀ3
Stepꢀ4
Navigateꢀtoꢀtheꢀdesiredꢀfolderꢀandꢀfile.
• To go up one folder level, press ESC once.
• To view the contents of a highlighted folder, press
SELECT.
Note: the "FOLDERUP" option may also be selected to
navigate up one folder level.
PressꢀSELECT to begin playing the selected MP3/WMA file.
Note: Press ESC from the root directory to exit search mode.
12
XDMA7650ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
*Folder access is only available on MP3/WMA discs recorded
with more than one folder.
Repeat Press RPTꢀto enter the Repeat menu, then turn the volumeꢀ
knob to select one of the following options:
• OFF - Plays all tracks on CD.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random Press RDMꢀto enter the Random menu, then turn the volumeꢀ
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between other modes and when the unit is turned on/off.
Intro Press INTꢀto enter the Intro menu, then turn the volumeꢀknob
to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
Note: Folder repeat, random and intro options only function
on MP3/WMA discs recorded with more than one folder.
13
XDMA7650ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
MediaꢀCompatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s manual
for more information.
CompatibleꢀRecordingꢀ
Formats
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
14
XDMA7650ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AdditionalꢀMP3/WMAꢀ An internal buffer provides ESP (Electronic Skip Protection) to
Information virtually eliminate skipping.
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3 8kHz ~ 48kHz
WMA 32kHz ~ 48kHz
TransferꢀBitꢀrates
MP3 32kbps ~ 320kbps constant
Variable bit rates
WMA 32kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay ID3 tags Version 1.0 to 2.0.
This model will not display ID3 Version 2.0 or greater tags.
RecommendedꢀSettings For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
15
XDMA7650ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFiles
ConnectingꢀaꢀUSBꢀDevice
(soldꢀseparately)
Play MP3/WMA files from most mass storage devices by
connecting them to the XDMA7650's USB port.
PlayingꢀMusic
When a USB device is first connected, “READING” will
appear in the display and playback will begin momentarily.
Depending on the number of files and folders, it may take
several seconds for the device to begin playing. If no valid
MP3/WMA files are detected, “NO FILE” will be displayed
and the last mode will be resumed.
TrackꢀSelect
Press TRACKꢀ
to skip to the beginning of the next
ll
track. Press TRACK
to return to the beginning of the
nn
current track. Pressing TRACK
beginning of the previous track.
again skips to the
nn
FastꢀForwardꢀandꢀ
Reverse
Press and hold TRACKꢀ
or TRACK
to fast
ll
nn
forward or reverse a track.
Pause
Press
Press
/
/
II to temporarily stop USB playback.
l
l
II again to resume playback.
FileꢀSearch
Stepꢀ1
Press SELECT to enter the USB file/folder search mode.
"USB SEARCH" will be displayed. A list of all the folders
from the USB device will be displayed.
Note: Any files located in the root directory will be located in
the folder named "ROOT". Press SELECT to view the files on
the root folder.
Stepꢀ2
Turn the volumeꢀknob to cycle through all the folders on the
device and press SELECT to choose the desired folder. The
list of files in the selected folder will be displayed. Turn the
volumeꢀknob to cycle through the list of files.
Stepꢀ3 Once the desired song is displayed, press SELECT to begin
playback of the desired song.
Pressing ESC when viewing the contents of a folder will
return to the list of folders on the USB device. Press ESC
again to exit the search menu.
Note: Due to differences in USB device transfer speeds, it is
recommended to limit each folder to less than 30 songs.
16
XDMA7650ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFiles
DisplayingꢀInformation When a file is accessed, the clock and elapsed time will be
displayed. Press DISPLAY momentarily to select beween
artist, song title, file name, folder name, track number and
clock/elapsed time.
ꢀꢀ
"NO TITLE" will be displayed if no song title information is
available.
"NO ARTIST" will be displayed if no artist information is
available.
SongꢀTitleꢀIconꢀ
ArtistꢀIconꢀ
FolderꢀIconꢀ
FileꢀIconꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the folder name is displayed.
This icon will illuminate when the file name is displayed.
ꢀ
FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
Note: Folder access is only available on USB devices with
more than one folder.
Repeat Press RPTꢀto enter the Repeat menu, then turn the volumeꢀ
knob to select one of the following options:
• OFF- Plays all tracks on USB device.
• TRACK - Continuously repeats selected track.
• FOLDER - Continuously repeats all files in selected folder.
Random Press RDMꢀto enter the Random menu, then turn the volumeꢀ
ꢀ
knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• FOLDER - Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between other modes and when the unit is turned on/off.
Press INTꢀto enter the Intro menu, then turn the volumeꢀknob
to select one of the following options:
Intro
• OFF - Cancels the INTꢀfunction.
• ALL - Plays first 10 seconds of each track.
• FOLDER - Plays first 10 seconds of each track in folder.
17
XDMA7650ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFiles
CharacterꢀSupport
Maximum character display information
• Track name – 32 character maximum
• Directory name – 32 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
*Song title and artist name will only be displayed if included
with the MP3/WMA file.
MediaꢀCompatibility
The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on order the files
are copied to the USB device and begins in the root folder.
Any empty folders or folders that do not include MP3/WMA
files are skipped. Depending on your software, the playback
order may vary.
PlaybackꢀCapacity
• Maximum number of files: 48896
• Maximum number of folders: 127 plus the root directory
• Maximum number of files in each folder and root: 382
• Maximum number of folder levels (sub folders): 8
(7 levels plus the root)
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
Note:ꢀDevices that exceed the maximum number of files or
folders may not function properly.
USBꢀDeviceꢀCompatibility
Due to the differences of USB devices, some devices may
not be compatible. USB devices must be ‘mass storage
class’ and formatted to the FAT or FAT32 file system in
order to ensure compatibility.
18
XDMA7650ꢀOPERATION
USBꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AdditionalꢀMP3/WMAꢀ Only MP3 files with filename extension (.mp3) can be played.
Information Only WMA files with filename extension (.wma) can be played.
Do not attempt to play non-MP3/WMA files with the MP3/WMA
extension.
SamplingꢀFrequencyꢀRates
MP3 8kHz ~ 48kHz
WMA 32kHz ~ 48kHz
TransferꢀBitꢀrates
MP3 32kbps ~ 320kbps constant
Variable bit rates
WMA 32kbps ~ 192kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay ID3 tags Version 1.0 to 2.0
Note: If an invalid ID3 tag version is detected, "NO SUPPORT"
will scroll on the display.
19
XDMA7650ꢀOPERATION
OperationꢀofꢀiPod
ConnectꢀanꢀiPodꢀDevice The XDMA7650 features a direct USB control system for
(NotꢀIncluded) iPod. To play music from an iPod device, connect the USB
cable (included with your iPod device) to the XDMA7650's
USB port. Once connected, READING will appear in the
display. Playback will begin automatically. If a song is
playing on the iPod device before it is connected, it will
continue to play.
DisplayingꢀInformation
Press DISPLAY to select between artist, song title, album,
elapsed time, clock and track number.
SearchꢀMode
SearchꢀMenuꢀFunctions
(stepꢀ1)
Press SELECT once to enter the search mode.
(stepꢀ2)
Turn the volume knob to select between playlist, artist,
album, song,ꢀaudiobook and podcast. Press SELECT to select
the desired search type.
(stepꢀ3)
Navigate to the desired song and press SELECT to begin
playback of that song. Use the table below for reference
when navigating through the menu options.
Note: Press ESC to access the previous level (up one level).
Pressing ESCꢀfrom the search main menu will exit the
search.
See the below table for a list of the search menu navigation options.
Menu Navigation
Songs
Search Item
Menu
Playlists
Playlist
Artist
Menu
Menu
Menu
Menu
Menu
Artists
Albums
Songs
Songs
Album
Song
Audiobooks
Podcast
Albums
Songs
Audiobooks
Podcasts
20
XDMA7650ꢀOPERATION
OperationꢀofꢀiPod
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀSongꢀSelect
Press
to skip to the beginning of next song. Press
ll
to return to the beginning of current song. Pressing
again skips to the beginning of previous song.
nn
nn
ꢀꢀFastꢀForwardꢀandꢀ
Press and hold
song.
or
to fast forward or reverse a
ll nn
Reverse
ꢀꢀ
Pause
Press / II again to resume playback.
Press / II to temporarily stop playback.
l
l
Repeat
Press RPTꢀto enter the Repeat menu, then turn the volume
knob to select one of the following options:
• OFF - Repeats all tracks.
• SONG - Repeats selected track.
Random
Press RDMꢀto enter the Random menu, then turn the
volume knob to select one of the following options:
• OFF - Cancels the RDMꢀfunction.
• ALL- Plays all tracks in random order.
• ALBUM - Plays all tracks in the selected album in
random order.
Intro
Press INTꢀto enter the Intro menu, then turn the volume
knob to select one of the following options:
• OFF - Cancels the INTꢀfunction.
• ON - Plays first 10 seconds of each track.
CharacterꢀSupport
Only alphanumeric characters can be displayed (ASCII
type). "NO SUPPORT" will be displayed if the file contains
characters that can not be displayed. "NO FILE" will be
displayed if there are no songs in the selected playlist.
Maximum character display information
• *Song title – 32 character maximum
• *Artist name – 32 character maximum
• *Album name – 32 character maximum
*Song Title, Artist Name and Album name will only be
displayed if included with the file.
DeviceꢀCompatibility
Made for
• iPod nano (5th generation)
• iPod touch (2nd generation)
• iPod nano (4th generation)
• iPod classic
• iPod touch (1st generation)
• iPod nano (3rd generation)
• iPod nano (2nd generation)
• iPod with video
• iPhone 3GS
• iPhone 3G
• iPhone
21
XDMA7650ꢀWARRANTY
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal
rights. You may also have other rights
which vary from state to state.
Whatꢀtoꢀdo?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any
custom controls may save you a service
call.
Dual Electronics Corp. warrants this
product to the original purchaser to be free
from defects in material and workmanship
for a period of one year from the date of
the original purchase.
2. If you require service during the
warranty period, you must carefully
pack the product (preferably in the
original package) and ship it by prepaid
transportation with a copy of the original
receipt from the retailer to an
Dual Electronics Corp. agrees, at our
option, during the warranty period,
to repair any defect in material or
workmanship or to furnish an equal
new, renewed or comparable product
(whichever is deemed necessary) in
exchange without charges, subject to
verification of the defect or malfunction and
proof of the date of purchase. Subsequent
replacement products are warranted for
the balance of the original warranty period.
authorized service center.
3. Please describe your problem in
writing and include your name, a
return UPS shipping address (P.O. Box
not acceptable), and a daytime phone
number with your shipment.
4. For more information and for the
location of the nearest authorized
service center please contact us by one
of the following methods:
Whoꢀisꢀcovered? This warranty is extended
to the original retail purchaser for products
purchased from an authorized Dual dealer
and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered? This warranty covers all
defects in material and workmanship in
this product. The following are not covered: Exclusion of Certain Damages: This
software, installation/removal costs,
damage resulting from accident, misuse,
abuse, neglect, product modification,
improper installation, incorrect line
voltage, unauthorized repair or failure
to follow instructions supplied with the
product, or damage occurring during
return shipment of the product. Specific
warranty is exclusive and in lieu of any
and all other warranties, expressed or
implied, including without limitation the
implied warranties of merchantability and
fitness for a particular purpose and any
obligation, liability, right, claim or remedy
in contract or tort, whether or not arising
from the company’s negligence, actual
license conditions and copyright notices for or imputed. No person or representative
com.
is authorized to assume for the company
any other liability in connection with the
sale of this product. In no event shall the
company be liable for indirect, incidental or
consequential damages.
22
XDMA7650ꢀOPERATION
Troubleshootingꢀ
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
Insulate all bare speaker wires
from each other and chassis
ground
One or more speaker wires touching
each other or touching chassis ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Unitꢀblowsꢀfuses
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
Unit is not mounted correctly or
backstrap is not secure
Check mounting sleeve and
backstrap support
Excessiveꢀskipping
Physical defect in media (CD, CD-R or
CD-RW)
Check media for scratches
Press eject or RESET
Press eject or RESET
ERROR-01ꢀappearsꢀ
onꢀdisplay
Disc read error
ERROR-02ꢀappearsꢀ
onꢀdisplay
Focus error or disc is in upside down
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM Write disc using WMA files that
(Digital Rights Management)
are not copy-protected
NOꢀFILEꢀappearsꢀ
onꢀdisplay
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
Write disc using valid audio
files with .mp3 or .wma file
extensions
INVALIDꢀappearsꢀ
onꢀdisplay
The file format is incompatible
Press and hold EJECTꢀ
for 3 seconds to reset CD
mechanism position
CD mechanism position out of
alignment
Unitꢀwillꢀnotꢀacceptꢀ
aꢀdisc
Remove 2 transit screws
located on top of the unit
CD transit screws still in place
NOꢀSUPPORTꢀappearsꢀ
onꢀdisplay
Version 1.0 to 2.0 ID3 tags are
supported.
An invalid ID3 tag version is present
23
XDMA7650ꢀOPERATION
Specifications
CDꢀPlayer Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1ꢀBit
FMꢀTuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AMꢀTuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVoltsꢀRMS
Dimensions: 7"ꢀxꢀ7"ꢀxꢀ2"ꢀ(178ꢀxꢀ178ꢀxꢀ51ꢀmm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
24
XDMA7650ꢀOPERATION
FCCꢀCompliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
25
XDMA7650ꢀOPERATION
Notes
26
XDMA7650ꢀOPERATION
Notes
27
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2010 Dual Electronics Corp. All rights reserved.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible
for the operation of this device or its compliance with safety and regulatory standards.
Other trademarks and trade names are those of their respective owners.
NSA0710-V01
|