O W N E R ’ S G U I D E
INSTALLATION GUIDE
12” (16:9)
Overhead Video
Monitor
MODEL OHV1202
© 2005 Directed Electronics, Inc. N81122 03-05
Table of Contents
Non-Transferable Limited One Year Consumer Warranty . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . .5
Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
When Cleaning the Vehicle .............................................................................5
While Driving ...............................................................................................5
When Parked ................................................................................................5
Proper Use ...................................................................................................5
Repairs........................................................................................................6
Radio/TV Tuner Use.......................................................................................6
Installation..................................................................................................6
Picture Quality..............................................................................................6
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
FCC Notice ...................................................................................................7
Your Warranty...............................................................................................7
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Monitor .......................................................................................................8
Setting the Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Remote Conntrol Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Remote Buttons ..........................................................................................10
IR Remote Feedthrough................................................................................11
Battery Replacement....................................................................................12
Precautions ................................................................................................12
Operating the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Open/Close the Display Monitor.....................................................................13
Power Up/Down the Display Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
P (Picture-In-Picture/Split Screen).................................................................14
Source (Mode) ............................................................................................14
Menu (Console Menu)...................................................................................15
Door Light On/Off .......................................................................................15
Courtesy Light On/Off ..................................................................................15
Installing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . .17
Precautions ................................................................................................17
Electrical Connections..................................................................................18
Signal Connections ......................................................................................19
Typical Wiring Diagram.................................................................................20
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
System Wiring Diagram Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
© 2005 Directed Electronics, Inc.
3
Safety Instructions and Cautions
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIP-
MENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND
ANNOYING INTERFERENCE, USE ONLY THE INCLUDED HARDWARE.
THIS MONITOR IS ONLY DESIGNED FOR REAR SEAT PASSENGER VIEWING AND IS NOT
INTENDED FOR VIEWING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION. SUCH USE MAY
DISTRACT THE DRIVER OR INTERFERE WITH THE SAFE OPERATION OF THE VEHICLE, AND
MAY ALSO VIOLATE STATE LAW.
DIRECTED ELECTRONICS, INC. DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY,
INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR
UNINTENDED USES OF THIS PRODUCT.
SHOULD THE LCD PANEL BREAK OR LEAK FLUID, AVOID ALL CONTACT WITH THE UNIT. IF
YOU SHOULD COME IN CONTACT WITH THE LEAKED FLUID, WASH THE AFFECTED AREA
THOROUGHLY WITH WATER AND SEEK IMMEDIATE MEDICAL ATTENTION.
■
During operation, if the unit should over-heat or malfunction, switch off the unit and see your
dealer. Do not disassemble the unit as there are no user-serviceable parts in this unit and the war-
ranty will be voided.
■
Should there be a need to replace a blown fuse, turn off the unit and disconnect all power to
the player. Use only the correct rating fuse to avoid electrical damage to the unit.
■
Only operate the monitor as described in this guide. Attempts to use or modify this monitor
contrary to the descriptions in this guide may cause damage and void the warranty.
■
Extremes in temperature can cause abnormal display operation. This monitor has an optimal
operating temperature range between 32–120 degrees Fahrenheit. If the vehicle interior is outside
this range, do NOT operate the monitor until the temperature is within its operating range.
■
Exposure to moisture or dust can cause harmful damage to the internal electronics. Do not
mount near cup holders or in areas where spills may occur.
■
This monitor is designed for use in vehicles with standard (-) 12 volt ground electrical systems.
■
Do not operate for an extended period of time without the engine running or the vehicle’s bat-
tery voltage may drop to levels precluding engine starting.
■
Do not drop the LCD panel or subject it to direct impact. This will damage the panel and/or
the back light element.
■
When operating the unit, avoid contact with the LCD panel.
■
Prevent metal or foreign objects being locked between the LCD screen and the enclosure.
■
Keep unit away from equipment with strong magnets such as large loudspeakers.
© 2005 Directed Electronics, Inc.
4
Welcome
Thank you for your purchase of Directed’s Overhead Monitor. Prior to operating this unit, please fully
read this instruction manual and retain it for future reference.
What’s Included
The following items are included with your purchase:
z Monitor
z Power Harness (2)
z DIN Cable
z A/V Switch Box
z (2) Headphones (HP200)
z Remote Control
z Domelight Harness
z Mounting Trim Gasket
z Mounting Plate (with 4 screws)
Important
WHEN CLEANING THE VEHICLE
Do not spray this unit with water or cleaning solutions. Moisture and the chemicals found in cleaning
fluids could damage the consoles finish and interior electronics. A soft damp, lens cleaning cloth
should be used to wipe the screen. Do NOT use any type of scouring pad, abrasive cleaners, or solvents.
WHILE DRIVING
This unit is intended for use in the rear seat area only. It is illegal in some jurisdictions to install the
unit in a location that would allow the driver to view it while driving.
WHEN PARKED
The screen is easily visible when deployed. Always close the screen when parking for an extended
period of time to avoid potential theft or extended exposure to direct sunlight.
PROPER USE
Do not touch the screen. Do not pull or hang from the fold down monitor door.
© 2005 Directed Electronics, Inc.
5
REPAIRS
If the monitor stops working for any reason, discontinue use immediately and consult with your
retailer about any necessary repairs.
RADIO/TV TUNER USE
When the unit is used in conjunction with a Radio/TV tuner, please assure that the receiver is man-
ufactured to receive television broadcast signals that are transmitted via terrestrial radio waves.
Reception quality will change and vary according to vehicle location and weather conditions.
INSTALLATION
Avoid installing the monitor at a location, where it will be under direct sunlight or a hot air vent.
The operating temperature of the unit is from 32–120°F (0–50°C). Install the unit at a dry location,
where it is away from condensation.
Use only the correct size fasteners and cables during installation. Failure to do so may cause a
mechanical or electrical failure and create a fire hazard. The installation should be done by an
authorized Directed dealer.
NOTE: If the internal temperature of the vehicle is higher than the normal oper-
ating temperature, please allow the vehicle to cool down (or warm up) prior
to operating the unit.
PICTURE QUALITY
The picture quality of this LCD unit depends strictly on its installed location. To achieve the best
picture quality, adjust the brightness control or viewing angle of the unit until the optimum view-
ing is achieved.
© 2005 Directed Electronics, Inc.
6
Important Information
FCC NOTICE
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this device.
YOUR WARRANTY
Your warranty registration must be completely filled out and returned within 10 days of purchase.
Your product warranty will not be validated if your warranty registration is not returned. Make sure
you receive the warranty registration from your dealer. It is also necessary to keep your proof of pur-
chase, which reflects that the product was installed by an authorized dealer.
© 2005 Directed Electronics, Inc.
7
Controls
MONITOR
5
7
9
11
1
2
3
4
6
8
10
1.
2.
COURTESY LIGHT—Activate this switch to "ON/OFF" to activate the dome lights on the
monitor.
DOOR LIGHT On/Off—Engage this switch to have the door open switch activate
the dome lights.
3. IR Transmitter/Receiver—Infrared transmitter and receiver which transmits the audio to the
headphones and receives commands from the remote control.
4. OPEN/CLOSE—The latch to open or close the LCD screen.
P
5.
PICTURE—Each press of this button activates the Picture-In-Picture (PIP), split screen,
or normal feature.
S
6.
SOURCE—Selects the source to be used for the monitor (AV1, AV2, or other source with
option installed). This button will select the source for PIP or split screen mode, if PIP or split
screen are active.
M
7.
8.
MODE—Selects Full, Normal, Wide, or Zoom video presentation. It will select 4:3 or 16:9
for PIP video presentation, if PIP is active.
MENU—Used to set FM Frequency, Brightness, Contrast, Saturation, Hue, or Reset (menu
parameters). The menu will exit if no action is taken within a few seconds.
© 2005 Directed Electronics, Inc.
8
9.
UP Button—Used in conjunction with the
button to scroll up (or increase) the
button to scroll down (or decrease)
ꢁ
menu setting.
ꢀ
10.
11.
DOWN Button—Used in conjunction with the
the menu setting.
POWER—Power On/Off button.
Setting the Screen Mode
The overhead monitor has 4 different screen modes. These are: FULL, NORMAL, WIDE, and ZOOM.
button on the remote
Pressing the MODE M button on the front of the monitor or the Image
control can access the different screen modes. The last mode set is displayed on the screen. Each
time the Mode button is pressed, the screen switches in the following sequence.
© 2005 Directed Electronics, Inc.
9
Remote Control Unit
REMOTE BUTTONS
1
5
4
2
6
3
8
7
9
12
16
20
24
28
32
36
10
11
15
19
23
27
31
35
39
43
47
13
14
17
18
21
22
25
26
29
30
33
34
37
40
44
38
41
42
45
46
48
1. POWER (source)
2. IR (on/off)
3. FM (on/off)
4. Picture (PIP)
5-7. Numeric
28. ANGLE
29. SUBTITLE (on/off)
ꢁ
30. DOWN (Cursor)
31. AUDIO
32. ZOOM (2, 3, 4, 1/2, 1/3, 1/4, OFF)
33. F.REV (Fast Reverse)
34. PLAY/PAUSE
8. UP (display)
9-11. Numeric
12. Console MENU
13-15. Numeric
35. F.FWD (Fast Forward)
36. SLOW
© 2005 Directed Electronics, Inc.
10
16. DOWN (display)
17. MENU/PBC
37. BACK
38. STOP
18-19 Numeric
39. NEXT
20. Image
(wide, zoom, full, normal)
40. REPEAT
21. TITLE
41. POWER (Tuner)*
42. DSP (channel display)*
43. TV/AV (selects Tuner or Aux input)*
44. DISPLAY
22. UP (Cursor)
23. SETUP
ꢁ
24. MUTE (on/off)
25. LEFT (Cursor)
26. ENTER
45. CH+ (channel up)*
46. CH- (channel down)*
47. AUTO (auto programming of TV channels)*
48. PROGRAM
27. RIGHT (Cursor)
IR REMOTE FEEDTHROUGH
The remote will operate, through the monitor, and transmit commands to other compatible devices
attached to the AV1 or AV2 source at the switch-box. The IR signals are compatible with models
DV2602, DV2605 DVD players, and TV100 tuner.
NOTE: This remote is for the operation of the LCD screen and for the optional DVD
player. Some remote buttons only function when the optional DVD player is
installed in the monitor.
* These buttons are for use only with the TV tuner (model TV100).
© 2005 Directed Electronics, Inc.
11
BATTERY REPLACEMENT
NOTE: Before using remote after installation, remove the battery plastic protective slip.
Remote Controller
+ side
Battery
Latch
Battery Holder
1. Move the small latch to the right and slide out the battery holder.
2. Remove old battery and replace it with a new battery (CR2025) with the positive “+” sign facing
as shown above.
3. Push battery holder back into its compartment until it is locked.
PRECAUTIONS
1. Properly dispose of used battery.
2. Do not misuse battery by shorting the positive “+” and negative “-” terminal or put it into fire.
Overheating may cause the battery to explode and cause a fire hazard.
3. If the remote is not to be used for a long period, remove the battery from the remote to prevent
damage from battery leakage.
4. To avoid accidents, prevent children from playing with the battery.
© 2005 Directed Electronics, Inc.
12
Operating the Monitor
OPEN/CLOSE THE DISPLAY MONITOR
To open the display monitor, push the "OPEN" button and pull the monitor down by the middle of the
LCD to the desired position. Use the middle of the LCD screen to rotate to a desired viewing position.
WARNING: THE LCD MONITOR MUST ALWAYS BE OPENED, CLOSED, OR POSITIONED FROM
THE MIDDLE OF THE SCREEN AS SHOWN BY THE POINTING HAND BELOW. DO NOT USE THE
CORNERS OF THE SCREEN, THIS CAN RESULT IN DAMAGE/LEAKAGE OF THE SCREEN.
Open Button
Closed Position
Use this portion of the
screen for opening, closing,
Open Position
and positioning.
WARNING: DO NOT CLOSE THE LCD SCREEN IF A MEMORY CARD HAS BEEN INSERTED INTO
THE DVD PLAYER. THIS CAN CAUSE THE LCD SCREEN TO BREAK OR LEAK FLUID. IF YOU
SHOULD COME IN CONTACT WITH LEAKED FLUID, WASH THE AFFECTED AREA THOROUGHLY
WITH WATER AND SEEK IMMEDIATE MEDICAL ATTENTION. REMOVE ALL MEMORY CARDS
BEFORE CLOSING THE LCD SCREEN.
To close the display monitor, first rotate the LCD screen to align for closure and then push the LCD
screen up until it latches closed with an audible click.
Note: The ignition key must be in the Accessory or Ignition position in order for
the monitor to have power.
© 2005 Directed Electronics, Inc.
13
Power Up/Down the Display Monitor
The unit will power up when the display monitor is unlatched and pulled down. (If the unit does
not power up, press the Power
right side of the monitor.
button on either the remote or the Power
button on the
To turn the power off to the unit, press the POWER
button on the remote. The power will also
shut Off when the display monitor is placed in the closed and latched position.
If the hand icon or “INVALID KEY” displays in the upper left-hand corner of the screen when
using the remote, it indicates that the command issued is not allowed during the mode that the
monitor display is presently in, or is not available on this system.
P (PICTURE-IN-PICTURE/SPLIT SCREEN)
P
Select this feature by pressing
on the remote or the
button on the monitor to display
PIP or Split Screen viewing of a total of two inputs from the DVD, or the A/V inputs. When the sys-
tem is in PIP or Split Screen mode, the source feature described below only works on the small
inserted picture or on the split picture displayed on the right side of the monitor (if the optional
DVD player is installed).
NOTE: The switch on the HP200 headphones allow the listener to switch between
the two pictures (PIP or Split Screen). The IR button on the remote turns
the audio to the headphones On/Off.
SOURCE (MODE)
S
Press the
(SOURCE) button on the remote or the
button on the monitor to select the
input signal AV1, AV2 (or the optional DVD player or Hard Disk drive, if installed).
© 2005 Directed Electronics, Inc.
14
MENU (CONSOLE MENU)
Press "MENU"
button on the monitor or remote to activate the screen parameters set-up. The
sequence of set-up items is as follows:
FM →
SHARPNESS → BRIGHTNESS → CONTRAST →
SATURATION → HUE → RESET
FM: Transmitting frequency
BRIGHTNESS: Brightness adjustment
SATURATION: Color saturation adj.
SHARPNESS: Sharpness adjustment
CONTRAST: Contrast adjustment
HUE: Color hue adjustment
RESET: Resets above (except FM) to factory default settings.
Once the desired setting is selected, press the cursor buttons to adjust the setting. On the remote
use the up/down cursor buttons located at either side of the menu button. On the monitor use the
cursor buttons to the right side of the
button. If a button is not activated within 5 seconds,
this function mode will turn OFF. Once the correct function is selected, press the cursor button (to
set the desired setting). If no button is pressed, the menu mode will turn OFF in about 5 seconds.
The FM frequency setting allows the monitor to transmit audio to the vehicle’s radio. Use a frequency
that is not interfered with from a local broadcast station. This setting also has an OFF position.
DOOR LIGHT ON/OFF
Engage this switch
on the monitor to activate the dome lights when a door is open.
NOTE: This function is operational only when the Gray wire of the dome light cir-
cuit is connected to the door switch.
COURTESY LIGHT ON/OFF
Activate this switch
on the monitor to control the dome light illumination.
© 2005 Directed Electronics, Inc.
15
Installing Options
This unit allows the mounting of an optional DVD player or Hard Drive, not provided with this model.
NOTE: Before installing any options, ensure that the Power to the Monitor is Off
and that the ignition key is Off.
1. Open the monitor and remove the protective cover from the monitor.
LCD Screen Side
Removal Assist
Front of Monitor
Locking Tabs (4)
2. Store the protective cover in an area where it will not be damaged.
3. Insert the optional DVD player or Hard drive as shown below.
NOTE: The illustration below shows a typical monitor with the DVD player option.
Insert DVD Player
and then slid down
until unit locks.
ꢀ
Lock/Unlock
Electrical
4. Refer to the manual that came with your option for operating instructions.
© 2005 Directed Electronics, Inc.
16
Installation Guide
PRECAUTIONS
1. This unit should be installed by an authorized Directed dealer.
2. When selecting a location to install this unit, be sure it does not interfere with the driver’s
ability to operate the vehicle or the driver's or passenger's safety.
3. This product is designed to operate with a 12V DC, negative ground battery system.
4. Disconnect the ground wire from the battery terminal prior to connecting the unit to the elec-
trical system.
NOTE: Head units with security codes will have to be reset after battery power is
restored.
5. The wiring from some other products or accessories might bear similar color code as this prod-
uct; however, they might be for other functions. Please refer to the electrical connection diagrams
of this product prior to installation to avoid improper connection.
6. Use proper connectors and insulation to prevent electrical damage to the unit.
6. Do not connect the yellow wire and red wire together of this product directly to the +12V.
Connect the red wire of this product to the ACC of the ignition key switch and yellow wire to +12V.
Failure to do so may result in discharge of the battery.
7. Only supplied accessories should be used to avoid damage to the unit during installation.
8. Ensure that the display monitor is suitably installed at a location, such that it will not obstruct
the rear view mirror and/or the air condition vents or operation of a sunroof.
9. Do not install this unit at a declining angle exceeding 30 degrees.
10. Do not install screws over the plane surface, which may affect the LCD screen deployment or
retract function.
© 2005 Directed Electronics, Inc.
17
ELECTRICAL CONNECTIONS
Power Cable (4–pin, one pin not used)
Color Code
Function
Black
Red
This wire is the ground source for the monitor and DVD.
Accessory +12V switched power source for the monitor and DVD. This
wire supplies the main power to the system (0.5A fuse).
Constant +12V power. This wire supplies power to the DVD for last
position memory (3A fuse).
Yellow
Secondary Power Cable (2–pin)
Color Code
Function
Black
Red
This wire is the ground source for the monitor and DVD.
Accessory +12V switched power source for the monitor and DVD. This
wire supplies the main power to the system (0.5A fuse).
Dome Light Cable (3–pin)
Color Code
Function
Black
Yellow
Gray
This wire supplies the ground to the domelight circuit.
This wire supplies +12V constant power to the domelight circuit.
This wire connects to the (-) door trigger.
© 2005 Directed Electronics, Inc.
18
SIGNAL CONNECTIONS
Adapter Audio
Color Code
Red 1 (RCA)
White 1 (RCA)
Red 2 (RCA)
White 2 (RCA)
Red 3 (RCA)
Function
Audio - Right (Input)
Audio - Left (Input)
Audio - Right (Input)
Audio - Left (Input)
Audio - Right (Output)
Audio - Left (Output)
White 3 (RCA)
Adapter Video
Color Code
Function
Yellow 1 (RCA)
Yellow 2 (RCA)
Yellow 3 (RCA)
Video - In (V-IN 1)
Video - In (V-IN 2)
Video - Out (V-OUT 1)
Adapter IR
In addition each IN 2 and IN 1 grouping has an IR output jack which passes the remote control com-
mands to the device (VCR, CD player, TV tuner or other devices) connected to this input.
© 2005 Directed Electronics, Inc.
19
TYPICAL WIRING DIAGRAM
POWER CABLE
RED–Ignition
YELLOW–12V Constant
BLACK–Ground
A/V
OUTPUT 3
A(R) A(L)
V
OUT
IN2
A(L) A(R)
IN1
IR
V
IR
V
A(L) A(R)
Wireless
Headphones
A/V
A/V
SOURCE 2 SOURCE 1
DOME LIGHT CABLE
YELLOW–12V Constant
BLACK–Ground
GRAY (-) Door Trigger
© 2005 Directed Electronics, Inc.
20
Installation Procedure
1. Identify the polarity of the dome light circuit and set the switch on the cable connection side
of the overhead monitor housing to match the vehicle’s door trigger polarity. Factory default posi-
tion for this switch is Negative. This switch is marked with the following instruction label.
ꢂ
Positive
Trigger Door
Switch
ꢃ
Negative
Trigger Door
Switch
Grey: Door Switch Yellow: +12V Black: Ground
Dome Light Wiring
2. Test fit the overhead monitor system on the ceiling of the vehicle, verifying it is not going to
interfere with the safe operation of the vehicle and is physically safe for the driver and passenger(s).
3. Once the mounting location of the overhead monitor system has been determined, carefully
mark the location with masking tape.
4. Lower the vehicle's headliner down to see if a roof support beam is available to screw the
mounting bracket to. If a support beam is not available to screw into, use a ¾" piece of plywood
cut to the appropriate size. Attach the plywood to the roof of the vehicle using silicone allowing
adequate drying time before proceeding.
5. Screw the mounting bracket in the vehicle. DOUBLE CHECK THE LENGTH OF THE SCREWS PRIOR
TO MOUNTING THE BRACKET, TO PRECLUDE PENETRATION OF THE VEHICLE’S ROOF.
© 2005 Directed Electronics, Inc.
21
Roof Beam Support
Optional Spacer Material
(Installer Provided)
Metal Bracket
Screws
(not included)
Screws
(Included)
6. Cut a 1" hole in the headliner along the backside of the mounting bracket for the cables to
pass through.
7. Route cables through the hole to the predetermined location of the AV source(s).
8. Identify the dome light wires in the vehicle and connect them to the corresponding dome light
wires on the overhead monitor system. Ensure the domelight switch is in the correct position.
9. Plug in the DIN, dome light cable and secondary power cables into the overhead monitor system.
10. Carefully hold the overhead monitor system to the mounting bracket aligning the mounting
holes while screwing in the screws. (Make sure the wires and cables are not in the way while mount-
ing the monitor).
11. Ground the Black wire of the power cable to a clean ground spot.
12. Connect the Yellow wire of the power cable to the battery positive terminal.
13. Connect the Red wire of the power cable to the Accessory wire in the ignition harness.
NOTE: Make sure you keep the ground wire of the monitor and video source as short
as possible to prevent unwanted audio noise pickup from the vehicle’s systems.
© 2005 Directed Electronics, Inc.
22
System Wiring Diagram Example
VCR
or
AUDIO AMPLIFIER
YELLOW
BATTERY (+12V)
Video In
BLACK (GROUND)
OUT
Power
RED (ACC)
IN
IN
DVD
DVD
or
TV Tuner
YELLOW
BLACK (GROUND)
+12V CONSTANT
GRAY (DOOR SWITCH)
IR Transmitter
NOTE: The Second Power cable must be connected or the unit will not operate and
will cause damage to the unit.
© 2005 Directed Electronics, Inc.
23
Troubleshooting
No Picture
Press the POWER
and SOURCE buttons (or the
button on the remote) to make sure the
monitor is on and the proper input is selected. If there is still no picture press the PICTURE button.
If the DVD menu appears, check the source unit.
If no DVD menu appears, check all fuses and power connections to the model. Inspect the connect-
ing cables for any fraying or breakage.
No Sound
If acquiring signal from another remote device (e.g. DVD player or CD player) ensure the device is
setup correctly.
The DVD player is in pause, slow motion, fast forward, or fast reverse mode. Place player in play
mode.
Picture Rolls
Check that the T.V. type setting is correct for the monitors and DVDs being used. PAL video often
rolls on NTSC monitors.
With a DVD player and a widescreen DVD disc, there are black bars on the screen
Change the TV display mode to "WIDE" in the DVD player's setup menu. After changing this setting,
if there are still black bars, press the MODE button on the remote control.
With a widescreen 16:9 monitor, I have black bars on the screen
Change the TV display mode to "Wide".
© 2005 Directed Electronics, Inc.
24
The Remote does NOT Function
Are there obstacles obstructing the view between the monitor and the remote.
The distance between the remote and monitor is too great.
The remote is not being pointed at the monitor’s IR receiver.
The batteries in the remote are weak.
DISC does NOT Play (with optional DVD player installed)
Parental code is set lower than than allowed by the DVD mounted.
Ensure the disk is mounted in the player with the correct orientation (shiny side up).
The disk is warped.
The player cannot play certain formats (see the beginning of this manual).
The region code on the DVD does not match the player.
Moisture condensation has occurred within the player. Leave the unit on and the disc access cover
open and try again after about 30 minutes.
The disc has not been properly finalized (formatted) when recorded. Refer to your manual that came
with your disc authoring equipment.
Unit does NOT Display or Operate Correctly
Press Reset button located on the monitor along side the removable DVD player location. This resets
all of the system, except for the Password and Parental Level setting.
© 2005 Directed Electronics, Inc.
25
Specifications
System
Laser
Semiconductor laser
NTSC, PAL
Signal Formats
Audio Characteristics
Frequency Response
DVD Video (PCM@ 96kHz)
20 Hz - 40 kHz 1dB
20 Hz - 20 kHz 1dB
20 Hz - 20 kHz 1dB
DVD Video (PCM@ 48kHz)
CD
Signal-to-Noise Ratio
Harmonic Distortion
Dynamic Range
90dB
0.01%
DVD Video
CD
95dB
95dB
Outputs (A/V Switchbox)
Audio (phono jacks)
Video (phono jack)
2 Vrms
1 V p-p @75 ohms
Inputs (A/V Switchbox)
Audio (phono jacks)
Video (phono jack)
General
2 Vrms
1 V p-p
Power Requirements
Power Consumption
Dimensions
14.4 VDC, 4.8 amps
69.2 watts
468 mm x 64 mm x 382 mm
(length/height/width)
18.4 in. x 2.5 in. x 15 in.
(length/height/width)
Mass
5.2 kg
11.5 lbs
Operating Temperature
Operating Humidity
0°–50°C
10% to 90%
32°–120°F
NOTE: Specifications and design are subject to change without notice.
© 2005 Directed Electronics, Inc.
26
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security, car stereo
products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of
advanced electronic technology, Directed is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America and around the world.
Call (800) 274-0200 for more information about our products and services.
Directed® is committed to delivering world-class quality products
and services that excite and delight our customers.
Directed Electronics, Inc.
Vista, CA 92081
© 2005 Directed Electronics, Inc.—All rights reserved
N81122 03-05
|