Canon Camcorder ZR70 MC User Manual
PUB.DIM-519  
Digital Video Camcorder  
English  
Instruction Manual  
Camescope vidéo numérique  
Françai  
s
Manuel d’instruction  
Videocámara digital  
Español  
Manual de Instrucciones  
Digital  
Video  
Cassette  
Mini  
This instruction manual covers the ZR70 MC, ZR65 MC and ZR60. Please note that  
illustrations and explanation in this manual are based on the ZR70 MC.  
Ce manuel d’instruction traite des modèles ZR70 MC, ZR65 MC et ZR60. Veuillez  
noter que les illustrations et les explications contenues dans ce manuel sont basées  
sur le ZR70 MC.  
Este manual de instrucciones cubre la ZR70 MC, la ZR65 MC, y la ZR60. Tenga en  
cuenta que las ilustraciones y las explicaciones de este manual se basan en la  
ZR70 MC.  
NTSC  
Important Usage Instructions  
WARNING:  
E
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS  
PRODUCT TO RAIN OR MOISTURE.  
WARNING:  
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING  
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.  
COPYRIGHT WARNING:  
Unauthorized recording of copyrighted materials may infringe on the rights of  
copyright owners and be contrary to copyright laws.  
Digital Video Camcorder, ZR70 MC/ZR65 MC/ZR60 systems  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  
This device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy  
and, if not installed and use in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of  
the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.  
If such changes or modifications should be made, you could be required to stop operation of the equipment.  
Canon U.S.A. Inc.  
One Canon Plaza, Lake Success, NY 11042, U.S.A.  
Tel No. (516)328-5600  
CAUTION:  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
The lightning flash with arrowhead  
symbol, within an equilateral triangle, is  
Important Warning  
intended to alert the user to the presence  
of uninsulated “dangerous voltage” within  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
the product’s enclosure, that may be of  
sufficient magnitude to constitute a risk of  
electric shock to persons.  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER (OR  
BACK). NO USER-SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO QUALIFIED  
The exclamation point, within an  
equilateral triangle, is intended to alert the  
user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature accompanying  
the product.  
SERVICE PERSONNEL.  
2
IMPORTANT SAFETY INSTRUCTIONS  
In these safety instructions the word “product”  
refers to the Canon Digital Video Camcorder  
ZR70 MC/ZR65 MC/ZR60 A and all its  
accessories.  
10. Power Sources — The CA-570 Compact  
Power Adapter should be operated only  
from the type of power source indicated on  
the marking label. If you are not sure of the  
type of power supply to your home, consult  
your product dealer or local power  
E
1. Read Instructions — All the safety and  
operating instructions should be read  
before the product is operated.  
company. Regarding other power sources  
such as battery power, refer to instructions  
in this manual.  
2. Retain Instructions — The safety and  
operating instructions should be retained  
for future reference.  
11. Polarization — The CA-570 Compact Power  
Adapter is equipped with a polarized 2-  
prong plug (a plug having one blade wider  
than the other).  
3. Heed Warnings — All warnings on the  
product and in the operating instructions  
should be adhered to.  
The 2-prong polarized plug will fit into the  
power outlet only one way. This is a safety  
feature. If you are unable to insert the plug  
fully into the outlet, try reversing the plug.  
If the plug still fails to fit, contact your  
electrician to replace your obsolete outlet.  
Do not defeat the safety purpose of the  
polarized plug.  
4. Follow Instructions — All operating and  
maintenance instructions should be  
followed.  
5. Cleaning — Unplug this product from the  
wall outlet before cleaning. Do not use  
liquid or aerosol cleaners. The product  
should be cleaned only as recommended in  
this manual.  
12. Power Cord Protection — Power cords  
should be routed so that they are not likely  
to be walked on or pinched by items placed  
upon or against them. Pay particular  
attention to plugs and the point from  
which the cords exit the product.  
6. Accessories — Do not use accessories not  
recommended in this manual as they may  
be hazardous.  
7. Avoid magnetic or electric fields — Do not  
use the camera close to TV transmitters,  
portable communication devices or other  
sources of electric or magnetic radiation.  
They may cause picture interference, or  
permanently damage the camera.  
13. Outdoor Antenna Grounding — If an  
outside antenna is connected to the  
product, be sure the antenna is grounded  
so as to provide some protection against  
voltage surges and built-up static charges.  
Section 810 of the National Electrical Code,  
ANSI / NFPA No. 70—1984, provides  
information with respect to proper  
8. Water and Moisture — Hazard of electric  
shock — Do not use this product near  
water or in rainy/moist situations.  
grounding of the mast and supporting  
structure, grounding of the lead-in wire to  
an antenna discharge unit, size of  
grounding conductors, location of antenna  
discharge unit, connection to grounding  
electrodes, and requirements for the  
grounding electrode. See figure 1.  
9. Placing or Moving — Do not place on an  
unstable cart, stand, tripod, bracket or  
table. The product may fall, causing serious  
injury to a child or adult,  
and serious damage to the  
product.  
A product and cart  
combination should be  
moved with care. Quick  
stops, excessive force, and uneven surfaces  
may cause the product and cart  
combination to overturn.  
3
18. Damage Requiring Service — Disconnect  
this product from the wall outlet and all  
power sources including battery, and refer  
servicing to qualified service personnel  
under the following conditions:  
EXAMPLE OF ANTENNA GROUNDING AS  
PER NATIONAL ELECTRICAL CODE  
Fig. 1  
ANTENNA  
LEAD IN  
WIRE  
GROUND  
CLAMP  
E
a. When the power-supply cord or plug is  
damaged.  
ANTENNA  
DISCHARGE  
UNIT  
(NEC SECTION  
810-20)  
b. If any liquid has been spilled onto, or  
objects have fallen into, the product.  
c. If the product has been exposed to rain  
or water.  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE  
GROUNDING ELECTRODE  
SYSTEM  
(NEC ART 250. PART H)  
NEC - NATIONAL ELECTRICAL CODE  
d. If the product does not operate normally  
even if you follow the operating  
instructions. Adjust only those controls  
that are covered by the operation  
instructions. Improper adjustment of  
other controls may result in damage and  
will often require extensive work by a  
qualified technician to restore the  
product to its normal operation.  
e. If the product has been dropped or the  
cabinet has been damaged.  
14. Lightning — For added protection of this  
product during a lightning storm, or when  
it is left unattended and unused for long  
periods of time, disconnect it from the wall  
outlet and disconnect the antenna. This will  
prevent damage to the product due to  
lightning and power-line surges.  
15. Overloading — Do not overload wall outlets  
and extension cords as this can result in a  
risk of fire or electric shock.  
f. When the product exhibits a distinct  
change in performance. This indicates a  
need for service.  
16. Objects and Liquid Entry — Never push  
objects of any kind into this product  
through openings as they may touch  
dangerous voltage points or short out parts  
that could result in a fire or electric shock.  
Be careful not to spill liquid of any kind  
onto the product.  
19. Replacement Parts — When replacement  
parts are required, be sure the service  
technician has used replacement parts that  
are specified by Canon or that have the  
same characteristics as the original part.  
Unauthorized substitutions may result in  
fire, electric shock or other hazards.  
17. Servicing — Do not attempt to service this  
product yourself as opening or removing  
covers may expose you to dangerous  
voltage or other hazards. Refer all servicing  
to qualified service personnel.  
20. Safety Check — Upon completion of any  
service or repairs to this product, ask the  
service technician to perform safety checks  
to determine that the product is in safe  
operating order.  
When replacement of power supply is required, please return it to the  
responsible nearest Canon Service Center and please replace it with the same  
type number CA-570.  
The Adapter can be used with a power supply between 100 and 240 V AC.  
For areas where 120 V AC power is not used, you will need a special plug  
adapter. Contact your nearest Canon Service Center for further information.  
4
Reference Guide  
The following manuals are supplied with the camcorder:  
E
❍ Digital Video Camcorder ZR70 MC/ZR65 MC/ZR60 Instruction Manual  
This manual explains the camcorder operations from basic video recording to the  
use of the full range of features.  
❍ Windows XP Users Only  
DV NETWORK SOLUTION DISK Software Instruction Manual  
This manual explains how to download/upload images from/to the memory card  
using a DV (IEEE1394) cable. You can also perform videoconference and file transfer  
over the Internet using the provided software. Available functions depend upon  
the camcorder model and networking environment.  
ZR70 MC ZR65 MC  
❍
DIGITAL VIDEO SOLUTION DISK Software Instruction Manual  
This manual explains how to download images from the memory card to a  
computer using the supplied USB cable. You can add sample images for Card Mix  
and My Camera settings from the supplied DIGITAL VIDEO SOLUTION DISK.  
Trademark Acknowledgements  
• Canon is a registered trademark of Canon Inc.  
• D is a trademark.  
•
logo is a trademark.  
• Macintosh is a trademark of Apple Computer Inc., registered in the United States  
and other countries.  
®
• Windows is either a registered trademark or trademark of Microsoft Corporation in  
the United States and/or other countries.  
• Other names and products not mentioned above may be registered trademarks or  
trademarks of their respective companies.  
5
Table of Contents  
Introduction  
E
Reference Guide..............................................................................................................5  
Thank You for Choosing a Canon ................................................................................9  
Introducing the ZR70 MC/ZR65 MC/ZR60 ..................................................................10  
Components Guide ......................................................................................................11  
Mastering the Basics  
Preparations  
Using a Household Power Source ..............................................................................15  
Attaching and Charging the Battery Pack ................................................................16  
Installing the Backup Battery ......................................................................................19  
Preparing the Camcorder ............................................................................................20  
Loading a Cassette........................................................................................................22  
Using the Wireless Controller......................................................................................24  
Setting the Time Zone, Date and Time......................................................................25  
Basic Recording  
Recording Movies on a Tape ......................................................................................28  
Zooming ........................................................................................................................30  
Using the LCD Screen....................................................................................................32  
Searching and Reviewing when Recording ..............................................................35  
Tips for Making Better Videos ....................................................................................36  
Basic Playback  
Playing Back a Tape ......................................................................................................37  
Playing Back on a TV Screen........................................................................................41  
Using the Full Range of Features  
General  
Menus and Settings ......................................................................................................44  
Changing the Remote Sensor Mode..........................................................................49  
Customizing the Camcorder........................................................................................50  
ZR70 MC  
Setting the Light-up Buttons ........................................................................51  
Other Camcorder Settings ..........................................................................................52  
Recording  
Changing the Recording Mode (SP/LP)......................................................................54  
Recording Still Images on a Tape................................................................................55  
Using the Recording Programs....................................................................................57  
Using Digital Effects......................................................................................................61  
Using the Multi-Image Screen ....................................................................................67  
Turning Off the Image Stabilizer ................................................................................69  
Recording With the Self-Timer....................................................................................70  
Audio Recording ..........................................................................................................71  
ZR70 MC  
Using the VL-3 Video Light (Optional) ........................................................73  
ZR70 MC  
Using the DM-50 Microphone (Optional)....................................................74  
Manual Adjustments  
Adjusting the Focus Manually ....................................................................................75  
6
Adjusting the AE Shift..................................................................................................77  
Setting the Shutter Speed............................................................................................78  
Setting the White Balance ..........................................................................................80  
Playback  
E
Magnifying the Image..................................................................................................82  
Displaying the Data Code ............................................................................................83  
Photo Search/Date Search............................................................................................85  
Returning to a Pre-marked Position ..........................................................................86  
Editing  
Recording to a VCR or Digital Video Device ............................................................87  
Recording from Analog Video Devices (VCR, TV or Camcorder) ..........................89  
Recording from Digital Video Devices (DV Dubbing)..............................................90  
Converting Analog Signals into Digital Signals (Analog-Digital Converter) ........92  
Replacing Existing Scenes (AV Insert) ........................................................................94  
Audio Dubbing..............................................................................................................96  
Connecting to a Computer Using a DV (IEEE1394) Cable ......................................99  
ZR70 MC ZR65 MC  
Using a Memory Card  
Inserting and Removing the Memory Card ............................................................100  
Selecting the Image Quality/Size ..............................................................................101  
Recording Still Images on a Memory Card..............................................................104  
Recording Panoramic Images (Stitch Assist Mode) ................................................107  
ZR70 MC  
Recording Motion JPEG Movies on a Memory Card................................109  
Playing Back a Memory Card ....................................................................................111  
Protecting Images ......................................................................................................114  
Erasing Images ............................................................................................................115  
Selecting Still Images for Printing (Print Order) ....................................................116  
Printing with the Direct Print Function....................................................................118  
Combining Images (Card Mix) ..................................................................................122  
Copying Still Images....................................................................................................126  
Formatting a Memory Card ......................................................................................128  
Connecting to a Computer Using a USB Cable ......................................................129  
Creating a Start-up Image ........................................................................................130  
Memory Card Information ........................................................................................131  
Additional Information  
Screen Displays ............................................................................................................134  
List of Messages ..........................................................................................................138  
Maintenance................................................................................................................141  
Troubleshooting ..........................................................................................................145  
System Diagram ..........................................................................................................148  
Optional Accessories ..................................................................................................149  
Specifications ..............................................................................................................152  
Index ............................................................................................................................154  
7
Conventions Used in This Manual  
Operating Modes  
E
Position of the  
POWER Switch  
Position of the  
TAPE/CARD Switch  
Operating Mode  
CAMERA  
PLAY (VCR)  
CAMERA  
TAPE  
TAPE  
CARD  
CARD  
PLAY (VCR)  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
Shaded area : ZR70 MC and ZR65 MC only.  
Available functions depend upon the operating mode. It is indicated as follows:  
CAMERA  
CAMERA  
: Function can be used in this mode.  
: Function cannot be used in this mode.  
Other Symbols and References  
❍
❍
❍
❍
❍
: Reference page number.  
: Functions to be operated on the body of the camcorder.  
: Functions to be operated on the wireless controller.  
: Additional topics that complement the basic operating procedures.  
: Precautions related to the camcorder operation.  
❍ Capital letters are used to refer to buttons on the camcorder or the wireless  
controller.  
❍ [ ] are used to refer to menu items displayed on the screen.  
❍ “Screen” refers to the LCD and the viewfinder screen.  
The serial number of this product can be found at the battery attachment unit of  
the camcorder. Write down the number and other information here and retain this  
book as a permanent record of your purchase to aid identification in case of theft.  
Date of Purchase:  
Purchased From:  
Dealer Address:  
Dealer Phone No.:  
Model Name: ZR70 MC/ZR65 MC/ZR60  
Serial No.:  
8
Thank You for Choosing a Canon  
The Canon ZR70 MC/ZR65 MC/ZR60 provides a full range of options and functions. We  
recommend reading this manual thoroughly before you use the camcorder. It will help  
you to become more familiar with your camcorder, and learn how to operate it  
properly.  
E
We suggest that you master the basic operations of the camcorder first, before  
moving on to its full range of features.  
Checking Supplied Accessories  
Two AA Batteries  
Lens Cap and Lens  
Cap Cord  
SS-800 Shoulder Strap  
ZR70 MC ZR65 MC  
WL-D79 Wireless Controller,  
ZR60  
WL-D80 Wireless  
Controller  
Lithium Button  
Battery CR1616  
CA-570 Compact  
Power Adapter (incl.  
power cord)  
ZR70 MC  
Battery Pack,  
ZR65 MC ZR60  
ZR70 MC  
WA-30.5  
Wide Attachment  
BP-512  
BP-508 Battery Pack  
STV-250N Stereo  
Video Cable  
ZR70 MC ZR65 MC  
IFC-300PCU USB Cable SDC-8M SD Memory  
Card (containing  
ZR70 MC ZR65 MC  
ZR70 MC ZR65 MC  
Hard Case for SD  
Memory Card  
sample images)  
DV NETWORK  
SOLUTION DISK  
ZR70 MC ZR65 MC  
DIGITAL VIDEO  
SOLUTION DISK  
9
Introducing the ZR70 MC/ZR65 MC/ZR60  
Advanced Accessory Shoe  
(ZR70 MC)  
22× Optical and  
440× Digital Zoom (ZR70 MC)  
E
Simply slide Canon’s DM-50 Directional  
Stereo Microphone or VL-3 Video Light  
into the accessory shoe; the camcorder  
will automatically provide power and  
connections.  
20× Optical and  
400× Digital Zoom (ZR65 MC)  
18× Optical and  
360× Digital Zoom (ZR60)  
Digital Effects  
Image Stabilizer  
Show your creativity by using the special  
effects and faders. The multi-image  
screen captures moving subjects in 4, 9 or  
16 sequences of still images.  
Stabilizes your recordings even in long  
telephoto shots (in Camera mode).  
Night Mode  
Memory Card (ZR70 MC/ZR65 MC)  
Allows recording even in dark places.  
The Night mode adjusts automatically to  
the optimum shutter speed.  
You can record images on a SD Memory  
Card or MultiMediaCard. Images  
recorded in Stitch Assist mode can be  
merged into one panoramic scene with  
the supplied software.  
Super Night Mode and  
Low Light Plus Mode (ZR70 MC)  
Direct Print (ZR70 MC/ZR65 MC)  
With the ZR70 MC’s Super Night mode  
(in Camera mode) and Low Light Plus  
mode (in Card Camera mode), you can  
keep on shooting without turning the  
lights on. The assist lamp (White LED)  
lights up to illuminate the subject.  
You can print still images by connecting  
to a Canon Bubble Jet Printer with Direct  
Print function.  
USB Terminal (ZR70 MC/ZR65 MC)  
Allows transfer of memory card data to a  
computer with built-in USB port. You can  
organize and edit images on your  
Still Images  
Just press the photo button to capture  
still images like photographs.  
computer using the supplied software.  
IEEE1394 DV Terminal  
My Camera Settings  
The DV terminal allows high-quality  
transfer with virtually no deterioration in  
quality of images. You can edit images  
by connecting the camcorder to a PC  
with IEEE1394 terminal. Windows XP  
Users can use the supplied software to  
perform videoconference and file  
transfer over the Internet.  
You can personalize your camcorder by  
customizing the start-up image and  
camcorder sounds.  
Analog Line-in Recording/  
Audio Dubbing/AV Insert Editing  
10  
Components Guide  
ZR70 MC/ZR65 MC/ZR60  
E
REC SEARCH + button (p. 35) /  
(fast forward) button (p. 37) /  
CARD + button* (p. 111)  
REC (record) SEARCH  
–
button (p. 35) /  
Record review button (p. 35) /  
(rewind) button (p. 37) /  
FOCUS button (p. 75) /  
CARD  
–
button* (p. 111)  
(play/pause) button (p. 37)  
AE SHIFT button (p. 77) /  
(stop) button (p. 37) /  
(index screen) button* (p. 112)  
LCD panel OPEN button (p. 32)  
BATT. (battery release)  
button (p. 16)  
LCD screen  
(p. 32)  
Serial number  
1
2
3
4
5
6
7
8
9
Battery attachment unit  
(p. 16)  
MENU button (p. 44)  
DC IN terminal (p. 15)  
Selector dial (p. 40, 44)  
Backup battery cover  
(p. 19)  
Card access indicator* (p. 104) /  
CHARGE indicator (p. 16)  
Memory card slot* (p. 100)  
DATA DIGITAL  
CODE EFFECTS ON/OFF  
(self-timer) button  
(p. 70) /  
DIGITAL EFFECTS  
button (p. 61)  
DATA CODE button  
(p. 83)  
Digital effects ON/OFF button  
(p. 61)  
Card MIX button*  
(p. 124) /  
Program selector (p. 57)  
MIX/  
SLIDE SHOW button*  
(p. 112)/  
SLIDE  
SHOW  
(stitch assist) button*  
(p. 107)  
Program AE  
Easy recording  
and  
only.  
ZR65 MC  
ZR70 MC  
*
11  
E
Diopter adjustment  
lever (p. 20)  
Viewfinder protect  
cover (p. 142)  
PHOTO button (p. 55, 104)  
ZR70 MC Advanced accessory  
shoe (p. 73)  
ZR65 MC ZR60 Accessory  
shoe (p. 150)  
Zoom lever (p. 30)  
Built-in speaker  
(p. 39)  
Viewfinder (p. 20)  
Strap mount (p. 21)  
TAPE/CARD switch*  
(p. 8)  
TAPE  
CARD  
Start/stop button  
(p. 28)  
Grip belt (p. 20)  
POWER switch (p. 8)  
Strap mount (p. 21)  
ER  
W
POOWER  
CAMERA  
OFF  
A
ER  
M
CAMERA  
FF  
O
AY  
PLAY  
)
CR  
(V  
}
PLAY(VCR)  
Cassette compartment  
cover (p. 22)  
Cassette compartment  
(p. 22)  
and  
only.  
ZR65 MC  
ZR70 MC  
*
12  
E
Terminal cover  
: Assist lamp  
ZR70 MC  
(White LED)  
(p. 59)  
Remote sensor (p. 24)  
Stereo microphone (p. 71)  
Terminal cover  
S-video IN/OUT  
terminal (p. 41)  
S
DV  
MIC  
AV  
DV IN/OUT terminal  
(p. 87)  
MIC terminal (p. 71)  
AV IN/OUT terminal  
(p. 41) / (phones)  
terminal (p. 39)  
Bottom view  
USB terminal *  
(p. 129)  
OPEN/EJECT switch (p. 22)  
Tripod socket (p. 36)  
and  
only.  
ZR70 MC  
ZR65 MC  
*
13  
Wireless Controller  
E
ZR70 MC ZR65 MC  
ZR60  
WL-D79  
WL-D80  
q
w
e
r
t
!
!
!
!
!
!
q
!
!
!
w
e
r
START  
ZOOM  
W
T
PHOTO  
START  
/STOP  
/STOP  
ZOOM  
W
T
PHOTO  
SELF T. D.EFFECT.  
TV SCREEN ON/OFF  
MENU  
SET  
!
SELF T. D.EFFECT.  
ON/OFF  
MENU  
SET  
!
#
!
@
@
TV SCREEN  
t
#
INDEX SLIDE SHOW  
CARD  
DATA CODE SEARCH SELECT  
ZERO SET  
@
@
#
y
u
DATA CODE SEARCH SELECT  
ZERO SET  
y
u
i
o
REW  
PLAY  
STOP  
SLOW  
FF  
MEMORY  
REW  
PLAY  
STOP  
SLOW  
FF  
MEMORY  
@
@
12bit  
AUDIO OUT  
@
@
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
AUDIO DUB. PAUSE  
2
@
AV INSERT AV DV REMOTE SET  
i
o
@
@
AV INSERT AV DV REMOTE SET  
REC  
PAUSE  
@
@
@
@
REC  
PAUSE  
!
!
-
WIRELESS CONTROLLER WL D80  
-
WIRELESS CONTROLLER WL D79  
@
@
@
@
#
!
!
!
!
!
!
@
#
PHOTO button (p. 55, 104)  
MENU button (p. 44)  
SET button (p. 44)  
!
!
@
@
@
@
@
@
@
@
@
@
#
#
#
#
q
w
e
r
t
y
u
i
o
!
!
!
!
!
!
!
!
D. EFFECTS (Digital effects) button (p. 61)  
START/STOP button (p. 28)  
SELF T. button (p. 70)  
Search buttons (p. 85)  
PLAY button (p. 37)  
TV SCREEN button (p. 134)  
DATA CODE button (p. 83)  
FF  
button (p. 37)  
button (p. 38)  
SEARCH SELECT button (p. 85)  
ZERO SET MEMORY button (p. 86)  
12bit AUDIO OUT button (p. 98)  
AUDIO DUB. button (p. 97)  
STOP button (p. 37)  
2 button (p. 38)  
REMOTE SET button (p. 49)  
SLOW button (p. 38)  
AV DV button (p. 93)  
button (p. 38)  
REC PAUSE button (p. 89)  
REW  
button (p. 37)  
AV INSERT button (p. 95)  
Digital effects ON/OFF button (p. 61)  
Transmitter  
PAUSE button (p. 38)  
INDEX button* (p. 112)  
SLIDE SHOW button* (p. 112)  
Zoom buttons (p. 30)  
CARD  
buttons* (p. 111)  
Controller buttons (p. 44)  
and  
only.  
ZR65 MC  
ZR70 MC  
*
14  
Using a Household Power Source  
You can operate the camcorder from a household power source using the supplied  
power adapter. The power adapter converts current from a power outlet (100-240 V  
AC, 50/60 Hz) to the DC current used by the camcorder.  
E
1. Turn the POWER switch to OFF.  
2. Connect the power cord to the  
ER  
W
POOWER  
q
power adapter.  
A
ER  
M
CAAMERA  
FF  
OFF  
AY  
PL  
CR  
)
(V  
3. Plug the power cord into a power  
outlet.  
4. Connect the power adapter to the  
camcorder’s DC IN terminal.  
r
w
e
5. After use, disconnect the power adapter from the camcorder. Unplug  
the power cord from the power outlet and disconnect it from the  
adapter.  
❍ Turn off the camcorder before connecting or disconnecting the power adapter.  
❍ If the adapter is used close to a TV, it may cause picture interference. Move the  
adapter away from the TV or the antenna cable.  
❍ Do not connect any products that are not expressly recommended to the  
camcorder’s DC IN terminal or to the power adapter.  
❍ You may hear some noise from the power adapter during use. This is not a  
malfunction.  
15  
Attaching and Charging the Battery Pack  
Charge the battery pack with the supplied power adapter before you use the  
camcorder for the first time and subsequently when the message “CHANGE THE  
BATTERY PACK” appears.  
E
1. Turn the POWER switch to OFF.  
q
w
2. Move the viewfinder upward.  
3. Attach the battery pack to the  
camcorder.  
ER  
W
POOWER  
A
ER  
M
CAAMERA  
FF  
O
AY  
PL  
)
CR  
(V  
• Remove the terminal cover of the battery  
pack.  
• Align the end of the battery pack with the  
line on the camcorder, press lightly and slide  
it in the direction of the arrow until it clicks.  
e
click  
4. Connect the power cord to the  
adapter.  
DC IN terminal  
5. Plug the power cord into a power  
outlet.  
DC IN 8.4V  
6. Connect the power adapter to the  
camcorder’s DC IN terminal.  
7. When charging is complete,  
disconnect the power adapter from  
the camcorder. Unplug the power  
cord from the power outlet and  
disconnect it from the adapter.  
8. Remove the battery pack after use.  
Press the BATT. button to remove the battery.  
CARD/  
CHARGE  
CHARGE indicator y  
r
t
❍ The battery pack may be defective when the CHARGE indicator flashes rapidly.  
❍ The CHARGE indicator informs you about the charge status.  
0-50%:  
More than 50%: Flashes twice every second  
100%: Glows steadily  
Flashes once every second  
❍ Do not disconnect and reconnect the power cord while charging a battery  
pack. The battery pack may not be charged correctly even if the CHARGE  
indicator glows steady. The battery pack may also not be charged correctly  
when a power outage occurs during charging. Remove the battery pack and  
attach it back to the camcorder.  
16  
Charging, Recording and Playback Time  
Below times are approximate and vary according to the charging, recording or  
playback conditions.  
E
Charging Time  
Battery Pack  
Charging Time  
110 min.  
BP-508 (ZR65 MC/ZR60)  
BP-512 (ZR70 MC/optional)  
BP-511 (Optional)  
BP-522 (Optional)  
BP-535 (Optional)  
120 min.  
120 min.  
210 min.  
310 min.  
• Charge the battery pack in temperatures between 41º F and 104º F (5º C and 40º C).  
• A lithium ion battery pack can be charged at any charge state. Unlike conventional  
battery packs, you do not need to completely use or discharge it before charging.  
Recording Time  
Battery Pack  
Maximum Recording Time  
Typical Recording Time*  
Using the Viewfinder Using the LCD Using the Viewfinder Using the LCD  
BP-508  
(ZR65 MC/ZR60)  
100 min.  
180 min.  
75 min.  
55 min.  
95 min.  
40 min.  
75 min.  
BP-512  
(ZR70 MC/optional)  
140 min.  
BP-511 (Optional)  
BP-522 (Optional)  
BP-535 (Optional)  
180 min.  
370 min.  
590 min.  
140 min.  
295 min.  
470 min.  
95 min.  
195 min.  
315 min.  
75 min.  
155 min.  
250 min.  
* Approximate times for recording with repeated operations such as start/stop, zooming,  
power on/off. Actual time may be shorter.  
• We recommend that you prepare battery packs 2 to 3 times longer than you think you  
might need.  
• To conserve battery charge, turn off the camcorder instead of leaving it in record pause  
mode.  
Playback Time  
Battery Pack  
Playback Time  
Using the LCD  
70 min.  
BP-508 (ZR65 MC/ZR60)  
BP-512 (ZR70 MC/optional)  
BP-511 (Optional)  
125 min.  
125 min.  
BP-522 (Optional)  
250 min.  
BP-535 (Optional)  
400 min.  
17  
How much power is left?  
The battery symbols indicate the charge status of the battery  
pack.  
E
When the battery pack is empty, “CHANGE THE BATTERY PACK”  
appears for 4 seconds and  
starts flashing.  
The battery charge indicators are not constant – they vary  
according to the condition under which battery pack and  
camcorder are used.  
Battery Pack Handling Precautions  
DANGER!  
Treat the battery pack with care.  
• Keep it away from fire (or it might explode.)  
• Do not expose the battery pack to temperature higher than 140º F (60º C). Do  
not leave it near a heater or inside a car in hot weather.  
• Do not try to disassemble or modify it.  
• Do not drop or knock it.  
• Do not get it wet.  
❍ Charged battery packs continue to discharge naturally. Therefore, charge them on  
the day of use, or the day before, to ensure a full charge.  
❍ Attach the terminal cover whenever a battery pack is not in use. Contact to metallic  
objects may cause a short circuit and damage the battery pack.  
❍ Dirty terminals may cause a poor contact between the battery pack and the  
camcorder. Wipe the terminals with a soft cloth.  
❍ Since storing a charged battery pack for a long time (about 1 year) can shorten its  
lifecycle or affect performance, we recommend to discharge the battery pack fully  
and to store it in a dry place at temperatures no higher than 86˚ F (30˚ C). If you do  
not use the battery pack for long periods, charge and discharge it fully at least once  
a year. If you have more than 1 battery pack, perform these precautions at the  
same time for all battery packs.  
❍ Although the battery pack’s operating temperature range is from 32˚ F to 104˚ F  
(0˚ C to 40˚ C), the optimal range is from 50˚ F to 86˚ F (10˚ C to 30˚ C). At cold  
temperatures, performance will temporarily decline. Warm it in your pocket before  
use.  
❍ Replace the battery pack if the usable time after full charge diminishes substantially  
at normal temperatures.  
18  
Installing the Backup Battery  
The backup battery allows the camcorder to retain date, time and other camcorder  
settings while the power source is disconnected. Power the camcorder from a  
household power source or with a battery pack when replacing the backup battery.  
E
1. Open the backup battery cover.  
q
w
e
2. Insert the lithium battery with the  
+ side facing outward.  
3. Close the cover.  
WARNING!  
• The battery used in this device may present a fire or chemical burn hazard if  
mistreated. Do not recharge, disassemble, heat above 212° F (100° C) or  
incinerate the battery.  
• Replace the battery with a CR1616 made by Panasonic, Hitachi Maxell, Sony,  
Toshiba, Varta or Renata. Use of other batteries may present a risk of fire or  
explosion.  
❍ Do not pick up the battery using tweezers or other metal tools as this will  
cause a short circuit.  
❍ Wipe the battery with a clean dry cloth to ensure proper contact.  
❍ Keep the battery out of reach of children. If it is swallowed, seek medical  
assistance immediately. The battery case may break and the battery fluids may  
damage stomach and intestines.  
❍ Do not disassemble, heat or immerse the battery in water to avoid the risk of  
explosion.  
The backup battery has a life span of about a year. j flashes to inform you that  
it needs to be replaced.  
19  
Preparing the Camcorder  
Adjusting the Viewfinder (Diopter Adjustment)  
1. Turn on the camcorder and keep the  
LCD panel closed to adjust the  
E
viewfinder.  
2. Adjust the diopter adjustment lever.  
Do not leave the viewfinder exposed to direct sunlight as it may melt (due to  
concentration of light by the lens). Adjust the angle of the viewfinder to prevent  
sunlight from entering.  
Attaching the Lens Cap  
1. Attach the cord to the lens cap.  
2. Pass the grip belt through the loop  
on the cord.  
Press the buttons on the lens cap when  
attaching/removing it. Hook the lens cap on  
the grip belt while you are recording, and  
place it over the lens when you have finished.  
Fastening the Grip Belt  
Hold the camcorder with your right  
hand and adjust the belt with your left.  
Adjust the grip belt so that you can reach the  
zoom lever and photo button with your index  
finger, and the start/stop button with your  
thumb.  
20  
Attaching the Shoulder Strap  
For extra security and portability, attach the shoulder strap before using the  
camcorder.  
E
Pass the ends through the strap mount  
and adjust the length of the strap.  
ZR70 MC  
Mounting the Wide Attachment  
The WA-30.5 Wide Attachment gives you a wide perspective for indoor shots or  
panoramic views (0.6×). The wide attachment is for use at maximum wide-angle.  
Screw the wide attachment fully into  
the lens filter thread.  
❍ If you zoom to telephoto, the picture will not be in focus.  
❍ Do not look directly at the sun or other strong light sources through the wide  
attachment. It could damage your eyesight.  
❍ When recording in wide angle with the wide attachment, the outer periphery  
of the image may become curved.  
❍ Filters cannot be used with the wide attachment.  
❍ If dust accumulates on the wide attachment or on the camcorder lens, clean  
both lenses gently with a blower brush.  
❍ The wide attachment may obstruct the remote sensor (the range of the  
wireless controller narrows), or may cause a shadow to appear on the picture  
when recording with a video light or the assist lamp (White LED).  
❍ Do not touch the lens to avoid smudges and fingerprints.  
❍ Do not store the wide attachment in a humid place as it may mold.  
21  
Loading a Cassette  
Use only videocassettes marked with the D logo.  
E
Loading and Unloading  
1. Slide and hold the OPEN/EJECT  
switch and open the cassette  
w
Tape  
protection tab  
compartment cover.  
q
The cassette compartment opens  
automatically.  
2. Load/unload the cassette.  
• Load the cassette with the window facing  
the grip belt and the REC/SAVE tab facing  
upward.  
• Unload the cassette by pulling it straight  
out.  
e
P
U
S
H
3. Press the P mark on the cassette  
compartment until it clicks.  
Wait for the cassette compartment to retract  
automatically.  
4. Close the cassette compartment  
cover.  
click  
r
❍ Do not interfere with the cassette compartment while it is opening or closing  
automatically or attempt to close the cover until the cassette compartment has  
fully retracted.  
❍ Be careful not to get your fingers caught in the cassette compartment cover.  
❍ If the camcorder is connected to a power source, cassettes can be  
loaded/unloaded even if the POWER switch is set to OFF.  
❍ v flashes if no cassette is inserted when turning on the power (in CAMERA  
and PLAY (VCR) mode).  
❍ With some types of tapes, the remaining tape display may not be accurate.  
22  
Protecting Tapes from Accidental Erasure  
To protect your recordings from accidental  
erasure, slide the tab on the cassette to the  
left. (This switch position is usually labeled  
SAVE or ERASE OFF.)  
E
REC  
SAVE  
REC  
SAVE  
If you load a protected cassette in CAMERA  
mode, the message “THE TAPE IS SET FOR  
ERASURE PREVENTION” appears for approx. 4  
seconds and v starts flashing. If you wish to record on that cassette, slide the tab  
back to the right.  
Cassette Handling Precautions  
❍ Rewind tapes after use. If the tape becomes slack and damaged, it may cause  
picture and sound distortion.  
❍ Return cassettes in the case and store them upright.  
❍ Do not leave the cassette in the camcorder after use.  
❍ Do not use cassettes with spliced tapes or nonstandard cassettes as they may  
damage the camcorder.  
❍ Do not insert anything into the small holes of the cassette, or cover them with  
cellophane tape.  
❍ Handle cassettes with care. Do not drop or subject them to severe impact as this  
may damage the cassettes.  
❍ Rewind tapes from time to time if they are stored for a long time.  
❍ With cassettes equipped with a memory function, metal plated terminals may  
become dirty with use and the cassette’s memory function may not work properly.  
Clean the terminals with a cotton swab after about 10 times of loading/unloading.  
23  
Using the Wireless Controller  
You can operate the camcorder with the  
supplied wireless controller from a distance of  
up to 16 feet (5 m). Point it at the camcorder’s  
remote sensor when you press the buttons.  
E
Following functions cannot be operated  
without the wireless controller:  
• Some special playback modes (  
38)  
• Photo/date search (  
• Zero set memory (  
• Analog line-in (  
85)  
86)  
89)  
90)  
94)  
• DV dubbing (  
• AV Insert (  
• Audio dubbing (  
96)  
❍ The wireless controller may not work properly in bright places, such as  
outdoors under direct sunlight, or when used too close to the camcorder.  
❍ The operable range of the wireless controller may shorten when the  
camcorder’s remote sensor is exposed to strong light.  
❍ When the batteries run out, replace both at the same time.  
Inserting Batteries  
The wireless controller operates with two AA batteries.  
ZR70 MC ZR65 MC  
ZR60  
q
w
q
w
WL-D79  
WL-D80  
e
e
1. Open the battery cover.  
2. Insert the batteries following the + and – markings.  
3. Close the battery cover.  
24  
Setting the Time Zone, Date and Time  
Set the time zone, date and time when you first start using your camcorder. Install the  
E
backup battery before you begin (  
19).  
Setting the Time Zone/Daylight Saving Time  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
SYSTEM  
T.ZONE/DST•••N.Y.  
(
44)  
1. Press the MENU button to open the menu.  
MENU  
2. Turn the selector dial to select [SYSTEM] and press  
the selector dial.  
3. Turn the selector dial to select [T.ZONE/DST] and  
press the selector dial.  
• The time zone setting appears.  
• The default setting is New York. Select your time zone and daylight saving time (DST)  
setting if necessary.  
4. Turn the selector dial to select the setting option that represents your  
time zone.  
To adjust for daylight saving time, select the time zone with the U next to the area.  
5. Press the MENU button to close the menu.  
MENU  
25  
16  
1
4
E
19  
2
18  
24  
20  
3
17  
6
10  
7
9
15  
14  
8
5
21  
23  
12  
22  
11  
13  
14 15 16 17 18 19 20 21 22 23 24  
1
2
3
4
5
6
7
8
9
10 11 12 13  
No.  
No.  
Time zone  
LONDON  
PARIS  
Time zone  
WELLGTN (Wellington)  
SAMOA  
CAIRO  
HONOLU. (Honolulu)  
ANCHOR. (Anchorage)  
L.A. (Los Angeles)  
DENVER  
MOSCOW  
DUBAI  
KARACHI  
DACCA  
CHICAGO  
BANGKOK  
H. KONG (Hong Kong)  
TOKYO  
N.Y. (New York)  
CARACAS  
RIO (Rio de Janeiro)  
SYDNEY  
SOLOMON  
FERNAN. (Fernando de Noronha)  
AZORES  
❍ Once you have set time zone, date and time, you do not need to reset the  
clock each time you travel to another time zone. Just set the time zone to the  
one of your destination, and the camcorder automatically adjusts the clock.  
❍ Days per month and leap years will be automatically adjusted.  
Setting the Date and Time  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
D/TIME SET•••JAN. 1,2003  
12:00 PM  
SYSTEM  
(
44)  
1. Press the MENU button to open the menu.  
MENU  
26  
2. Turn the selector dial to select [SYSTEM] and press  
the selector dial.  
3. Turn the selector dial to select [D/TIME SET] and  
press the selector dial.  
E
The year display starts to flash.  
4. Turn the selector dial to select the year, and press the selector dial.  
• The next part of the display starts flashing.  
• Set the month, day, hours and minutes in the same way.  
5. Press the MENU button to close the menu and to  
MENU  
start the clock.  
Time zone, date and time appear for 4 seconds each time you  
turn the power on.  
❍ To change a part of the date or time, press the selector dial at step 4, and  
move to the part you wish to change.  
❍ The date can be set to any year between 2003 and 2030.  
Displaying Date and Time during Recording  
You can display time zone, date and time in the lower left corner of the screen (the  
time zone disappears after 4 seconds). The 4-second display will no longer appear  
when you turn the power on. The date and time display will not be superimposed on  
your recordings.  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
DISPLAY SET UP  
D/T DISPLAY••OFF  
(
44)  
1. Press the MENU button to open the menu.  
MENU  
2. Turn the selector dial to select [DISPLAY SET UP] and  
press the selector dial.  
3. Turn the selector dial to select [D/T DISPLAY] and  
press the selector dial.  
4. Turn the selector dial to select [ON].  
5. Press the MENU button to close the menu.  
MENU  
27  
Recording Movies on a Tape  
You can use the LCD screen or the viewfinder when recording.  
E
Before You Begin Recording  
Make a test recording first to check if the camcorder operates correctly. Before you  
make important recordings, clean the video heads (  
142).  
Preparations  
Connect a power source. Load a cassette.  
Recording  
1. Remove the lens cap.  
ZR70 MC/ZR65 MC  
2. Set the camcorder to CAMERA mode.  
q
TAPE  
CARD  
If you have not set the time zone, date and  
time, “SET THE TIME ZONE, DATE AND TIME”  
appears. See Setting the Time Zone, Date and  
Time (  
25).  
w
A
ER  
M
CAMERA  
FF  
OFF  
PL  
CR  
AY  
)
(VCR)  
3. Open the LCD panel (  
32).  
rt  
To use the viewfinder, keep the LCD panel  
closed or rotate it so that the screen faces in  
A
ER  
M
CAMERA  
F
F
OFF  
AY  
PL  
CR  
)
(VCR)  
the same direction of the lens (  
33).  
4. Press the start/stop button to begin  
recording.  
Wait until the tape counter came to a  
complete stop before you begin recording.  
5. Press the start/stop button again to  
pause recording.  
e
Restart recording by pressing the start/stop button.  
28  
When You Have Finished Recording  
1. Turn the POWER switch to OFF.  
2. Close the LCD panel.  
E
3. Replace the lens cap.  
4. Unload the cassette.  
5. Disconnect the power source.  
When recording outdoors or through a window, do not leave LCD screen,  
viewfinder or lens exposed to direct sunlight as it may cause damage.  
❍ Turn the power off if you do not intend to use the camcorder for a longer  
time.  
❍ The camcorder will shut off after 5 minutes when left in record pause mode to  
protect tape and video heads. To continue recording, turn the POWER switch  
to OFF and then back to CAMERA.  
❍ For when to use the [ (Easy Recording) or Q (program AE) mode, see Using  
the Recording Programs (  
57).  
❍ When you do not remove the cassette, you can record the next scene without  
producing any noise or blank sections between the recordings even if you turn  
the camcorder off.  
❍ About the built-in microphone: When recording near loud sounds (such as  
fireworks, drums or concerts), sound may become distorted or may be  
recorded not in the actual sound level.  
❍ For extra recording time, see Changing the Recording Mode (  
54).  
29  
Zooming  
The camcorder’s zoom lens allows you to choose the best picture angle for your  
recordings. The camcorder automatically switches between optical zooming and  
digital zooming. Image resolution is slightly lower with the digital zoom.  
E
Zoom in  
T
W
Zoom out  
Optical Zoom  
ZR70 MC  
ZR65 MC  
ZR60  
22× optical zoom  
20× optical zoom  
18× optical zoom  
Move the zoom lever toward W to zoom out (wide-  
angle). Move it toward T to zoom in (telephoto).  
• Press the zoom lever slightly for a slow zoom. Press harder for a  
faster zoom.  
• You can also use the T and W buttons on the wireless controller.  
However, you cannot control the zoom speed.  
Digital Zoom  
ZR70 MC  
ZR65 MC  
ZR60  
88×/440× digital zoom  
80×/400× digital zoom  
72×/360× digital zoom  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
CAMERA SET UP  
D.ZOOM••••••••88×  
(
44)  
1. Press the MENU button to open the menu.  
MENU  
2. Turn the selector dial to select [CAMERA SET UP] and  
press the selector dial.  
3. Select [D.ZOOM] and press the selector dial.  
4. Select a setting option.  
30  
5. Press the MENU button to close the menu.  
MENU  
E
❍ Keep at least 3.28 ft. (1m) to the subject. At wide-angle, you can focus on a  
subject as close as 0.39 in. (1cm).  
❍ A zoom indicator appears for 4 seconds. It extends in light blue when the  
digital zoom is set to 88×/80×/72×, and extends further in dark blue when set  
to 440×/400×/360×.  
❍ Digital zoom cannot be used in the Night mode and Super Night (ZR70 MC)  
mode.  
❍ Digital zoom cannot be used when the multi-image screen is selected.  
ZR70 MC ZR65 MC  
❍
Because the image stabilizer cannot be used in CARD  
CAMERA mode, we recommend mounting the camcorder on a tripod at large  
magnifications.  
31  
Using the LCD Screen  
1. Push the OPEN button at the LCD  
panel and open the LCD panel.  
E
The LCD screen switches on and the  
viewfinder switches off.  
2. Rotate the LCD panel and choose the  
angle of the screen.  
You can rotate the LCD panel so that the  
screen faces in the same direction as the lens  
(
33), or push it flat against the camcorder with the screen facing outward.  
3. Close the LCD panel after use.  
• Close the LCD panel firmly until it clicks.  
• The LCD screen switches off and the  
viewfinder switches on.  
❍ Make sure to open the LCD panel at 90 degrees before rotating it.  
❍ Rotate the LCD panel in the vertical position before closing the LCD panel.  
❍ When recording outdoors or through a window, do not leave the LCD screen,  
viewfinder or lens exposed to direct sunlight as it may cause damage.  
❍ Do not hold the camcorder by the LCD panel or the viewfinder.  
❍ About the LCD Screen: The LCD screen is produced with extremely high-  
precision manufacturing techniques, with more than 99.99% of the pixels  
operating to specification. Less than 0.01% of the pixels may occasionally  
misfire or appear as black or green dots. This has no effect on the recorded  
image and does not constitute a malfunction.  
❍ Bright light or reflected light may cause a vertical light bar to appear on the  
screen. This is not a malfunction.  
❍ Bright light may make it difficult to use the LCD screen. In such case, use the  
viewfinder instead.  
32  
Adjusting the Brightness of the LCD Screen  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
E
–
BRIGHTNESS••  
+
DISPLAY SET UP  
(
44)  
1. Press the MENU button to open the menu.  
MENU  
2. Turn the selector dial to select [DISPLAY SET UP] and  
press the selector dial.  
3. Turn the selector dial to select [BRIGHTNESS] and  
press the selector dial.  
4. Turn the selector dial and adjust the level.  
Turn the selector dial up to make the screen brighter and down to make it darker.  
5. Press the MENU button to close the menu.  
MENU  
Changing the brightness of the LCD screen does not affect that of the viewfinder  
or the recordings.  
Allowing the Subject to Monitor the LCD Screen  
You can rotate the LCD panel so that the  
screen faces in the same direction as the lens.  
The viewfinder switches on allowing you to  
use the viewfinder while the subject can  
monitor the screen.  
When you rotate the screen so that the screen faces in the same direction as the lens,  
the image appears mirror reversed (LCD MIRROR ON). However, you can choose to  
display the image as it is being recorded (LCD MIRROR OFF).  
33  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
DISPLAY SET UP  
LCD MIRROR••ON  
E
(
44)  
1. Press the MENU button to open the menu.  
2. Turn the selector dial to select [DISPLAY SET UP] and press the selector  
dial.  
3. Turn the selector dial to select [LCD MIRROR] and press the selector dial.  
4. Turn the selector dial to select [OFF].  
5. Press the MENU button to close the menu.  
When [LCD MIRROR] is set to [ON], most screen displays appear mirror reversed.  
34  
Searching and Reviewing when Recording  
REC SEARCH + button  
REC (record) SEARCH – button/  
v Record review button  
E
Record Review  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
In record pause mode, this function allows you to review the last few seconds of your  
recording to check if it has been recorded properly.  
Press and release the c (record review) button.  
The camcorder rewinds the tape, plays back the last few seconds,  
and returns to record pause mode.  
Record Search  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
In record pause mode, this function allows you to play back the tape (forward or  
reverse) to locate the point where you wish to begin recording.  
Press and hold the REC SEARCH + button (forward) or –  
button (reverse).  
• Release the button at the point you wish to begin recording.  
• The camcorder returns to record pause mode.  
❍ Noise may appear on the screen when you play back the tape in reverse.  
❍ There will be no sound during Record Review and Record Search.  
35  
Tips for Making Better Videos  
Holding the Camcorder  
E
For maximum stability, grip the camcorder in your right hand and keep your right  
elbow pressed against your body. If necessary, support the camcorder with your left  
hand. Be careful that your fingers do not touch the microphone or lens.  
Low-angle Recording  
High-angle Recording  
For More Stability  
Lean against a wall  
Put the camcorder on a table  
Lie on your elbow  
Use a tripod  
Lighting  
When recording outdoors, we recommend  
recording with the sun at your back.  
❍ When using a tripod, do not leave the viewfinder exposed to direct sunlight as  
it may melt (due to concentration of the light by the lens).  
❍ Do not use tripods with fastening screws longer than 0.2 inch (5.5 mm) as it  
may damage the camcorder.  
36  
Playing Back a Tape  
When you use the LCD screen for playback, the camcorder plays back the sound via  
built-in speaker. The built-in speaker is monaural. Use headphones for stereo sound or  
when using the viewfinder for playback.  
E
Preparations  
Connect a power source. Load a cassette.  
Playback  
1. Set the camcorder to PLAY (VCR)  
mode.  
ZR70 MC/  
ZR65 MC  
TAPE  
CARD  
q
A
ER  
M
CA  
FF  
O
AY  
PL  
)
CR  
(VCR)  
2. Open the LCD panel.  
r
e
t
You can also close the LCD panel with the  
screen facing outward.  
3. Press the ` button to rewind the  
tape.  
To fast forward the tape, press the 1  
button. To stop playback, press the 3 button.  
4. Press the e/a button to begin  
playback.  
w
5. Press the 3 button to stop playback.  
❍ If the playback picture is distorted, clean the video heads using a Canon Head  
Cleaning Cassette or a commercially available digital video head-cleaning  
cassette.  
❍ To use the viewfinder, close the LCD panel. The built-in speaker does not  
sound. Use headphones when using the viewfinder (  
❍ For displaying the date and time during playback, see Displaying the Data Code  
83).  
39).  
(
37  
Special Playback Modes  
Special playback modes (except of playback pause and fast/rewind playback) can only  
be operated with the wireless controller.  
E
` (rewind) button  
1 (fast forward) button  
REW  
PLAY  
STOP  
FF  
PAUSE SLOW  
2
3 (stop) button  
e/a (play/pause) button  
e/a (Playback Pause)  
To pause playback, press the e/a button. Press the e/a button to resume playback.  
The camcorder goes into stop mode after 5 minutes in playback pause mode.  
1 (Fast Forward Playback) / ` (Rewind Playback)  
Plays back the tape at 9.5 times normal speed (forward or reverse). Press and hold the  
button during normal playback or fast forward.  
+/ae (Frame Advance) / –/4a (Frame Reverse)  
Plays back frame-by-frame. Press the button repeatedly during playback pause. Press  
and hold it to play back continuous frame advance/frame reverse.  
SLOW I (Slow Forward)/(Slow Reverse)  
Plays back at about 1/3 normal speed. For slow forward playback, press the SLOW M  
button. For slow reverse playback, press the –/4a button followed by the SLOW M  
button. Press the e (play) button to return to normal playback.  
–/4a (Reverse Playback)  
Plays back in reverse at normal speed. Press the button during normal playback. Press  
the e (play) button return to normal playback. The camcorder goes into stop mode  
after 5 minutes in reverse playback pause.  
× 2 (Forward× 2 Playback)/(Reverse 2× Playback)  
Plays back at 2 times normal speed. Press the button during normal or reverse  
playback. Press the e (play) button return to normal playback.  
❍ There is no sound during special playback.  
❍ The picture may become distorted during some special playback modes.  
38  
Playing Back with the Built-in Speaker/Headphones  
Built-in speaker  
E
H (phones) terminal  
AV  
MENU button  
Selector dial  
When using the built-in speaker, make sure that “H” is not displayed on the  
screen. When using the headphones, make sure that “H” is displayed. Change  
the setting as necessary following the procedure below.  
Switching the AV/Headphones Terminal  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
VCR SET UP  
AV/PHONES•••AV  
(
44)  
1. Press the MENU button to open the menu.  
MENU  
2. Turn the selector dial to select [VCR SET UP] and  
press the selector dial.  
3. Turn the selector dial to select [AV/PHONES] and  
press the selector dial.  
4. Turn the selector dial to select [AV] or [PHONES H].  
5. Press the MENU button to close the menu.  
MENU  
❍ The built-in speaker does not sound when “H” is displayed.  
❍ Do not connect headphones unless “H” is displayed as it produces noise.  
❍ The built-in speaker is monaural. Use headphones for stereo sound.  
❍ The built-in speaker turns off when the camcorder is set to a mode other than  
the PLAY (VCR) mode or when you use the headphones.  
39  
Adjusting the Volume  
CAMERA*  
PLAY (VCR)  
CARD CAMERA*  
CARD PLAY (VCR)  
E
*Headphone volume only.  
Turn the selector dial up to increase the volume, and  
down to lower the volume.  
• A volume bar appears for 4 seconds.  
• You can turn off the volume completely by turning the selector  
dial down until OFF appears. Turn the selector dial up to increase the volume again.  
❍ Sound may become distorted when the volume is turned up too high.  
❍ The headphone volume can be adjusted in all operating modes.  
❍ The camcorder retains the setting even if you turn it off (separately for  
headphones and built-in speaker).  
40  
Playing Back on a TV Screen  
You can connect the camcorder to a TV or VCR to play back your recordings on a TV  
screen.  
E
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change  
the setting (  
39).  
❍ When you use the TV as a monitor during recording, keep the TV volume  
turned down as long as the camcorder’s audio terminals are connected. An  
unpleasant high-pitched squeal, called feedback, may be produced if sound  
from the TV speakers is picked up by the microphone.  
❍ For high picture quality, we recommend using a TV with an S (S1) terminal.  
❍ TVs with S1-terminal or Video ID-1 system: Recordings made in the 16:9 mode  
(
52) will be automatically played back in wide screen mode.  
TVs with S (S1)-Video Input Terminal  
Refer also to the TV or VCR instruction manual.  
S
DV  
INPUT  
S(S1)-VIDEO  
Signal flow  
S-150 S-video Cable (optional)  
VIDEO  
AUDIO  
L
AV  
Signal flow  
R
STV-250N Stereo Video Cable (supplied)  
1. Turn off all devices before starting the connections.  
2. Connect the S-150 S-video Cable (optional) to the S-video terminals.  
41  
3. Connect the STV-250N Stereo Video Cable to the camcorder’s AV  
terminal and the audio terminals of the TV/VCR.  
Connect the white plug to the white AUDIO terminal L (left), and the red plug to the  
red AUDIO terminal R (right). Do not connect the yellow plug.  
E
4. If connecting to a TV, set the input selector to VIDEO. If connecting to a  
VCR, set the input selector to LINE.  
TVs with Audio/Video Terminals  
Refer also to the TV or VCR instruction manual.  
VIDEO  
AUDIO  
L
R
AV  
Signal flow  
STV-250N Stereo Video Cable (supplied)  
1. Turn off all devices before starting the connections.  
2. Connect the STV-250N Stereo Video Cable to the camcorder’s AV  
terminal and the audio/video terminals on the TV/VCR.  
Connect the white plug to the white audio terminal L (left), the red plug to the red  
audio terminal R (right) and the yellow plug to the yellow video terminal VIDEO.  
3. If connecting to a TV, set the input selector to VIDEO. If connecting to a  
VCR, set the input selector to LINE.  
42  
Selecting the Audio Output Channel  
You can select the output channels when playing back a tape with audio recorded on  
two channels.  
E
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
AUDIO SET UP  
OUTPUT CH•••L/R  
(
44)  
1. Press the MENU button to open the menu.  
MENU  
2. Turn the selector dial to select [AUDIO SET UP] and  
press the selector dial.  
3. Turn the selector dial to select [OUTPUT CH] and  
press the selector dial.  
4. Turn the selector dial to select a setting option.  
• L/R: Stereo: L+R channels, Bilingual: Main+Sub.  
• L/L: Stereo: L channel, Bilingual: Main.  
• R/R:Stereo: R channel, Bilingual: Sub.  
5. Press the MENU button to close the menu.  
MENU  
The setting resets to the L/R setting when you turn the camcorder off.  
43  
Menus and Settings  
Many of the camcorder’s advanced functions are selected from menus that appear on  
the screen.  
E
Selecting Menus and Settings  
1. Set the camcorder to the correct operating mode.  
A
R
E
M
A
C
F
F
O
Y
LA  
P
)
R
C
(V  
ZR70 MC/ZR65 MC:  
TAPE  
CARD  
2. Press the MENU button to open the menu.  
MENU  
3. Turn the selector dial to select a submenu and press  
the selector dial.  
4. Turn the selector dial to select a menu item and  
press the selector dial.  
5. Turn the selector dial to select a setting option.  
6. Press the MENU button to close the menu.  
MENU  
When setting the white balance or shutter speed, press the  
selector dial first before pressing the MENU button.  
❍ Pressing the MENU button at any time closes the menu.  
❍ Selecting [[ RETURN] takes you back one level.  
❍ Items that are not available appear in purple.  
❍ You may find it more convenient to use the wireless controller to operate the  
menu. Press the MENU button on the wireless controller to open or close the  
menu. Use the arrow keys in place of the selector dial and press the SET button  
in place of pressing the selector dial.  
44  
Menu and Default Settings  
Default settings are shown in boldface.  
CAMERA Menu (CAM. MENU)  
E
PLAY (VCR)  
CARD CAMERA  
Setting Options  
CARD CHROMA, CARD LUMI.,  
CAM. CHROMA, C. ANIMATION  
CORNER, STRAIGHT, RANDOM  
CARD CAMERA  
CAMERA  
Submenu  
Menu Item  
\ CARD MIX *2 MIX TYPE  
122  
ANIMAT. TYPE  
123  
122  
78  
MIX LEVEL  
CAMERA SET UP SHUTTER  
D. ZOOM  
AUTO, 1/60, 1/100, 1/250, 1/500, 1/1000,  
1/2000  
ZR70 MC  
ZR65 MC  
ZR60  
30  
OFF, 88×, 440× OFF, 80×, 400× OFF, 72×, 360×  
IMAGE S. i  
ON, OFF  
69  
16:9  
WHITE BAL.  
ON, OFF  
52  
80  
AUTO, SET W, INDOOR T, OUTDOOR U  
VCR SET UP  
REC MODE  
SP, LP  
54  
39  
71  
71  
33  
34  
134  
27  
53  
51  
51  
49  
52  
25  
26  
50  
50  
50  
50  
50  
AV/PHONES  
WIND SCREEN  
AUDIO MODE  
AV, PHONES H  
ON, OFF  
AUDIO SET UP  
16bit, 12bit  
DISPLAY SET UP BRIGHTNESS  
LCD MIRROR  
ON, OFF  
TV SCREEN  
ON, OFF  
D/T DISPLAY  
ON, OFF  
DEMO MODE  
ON, OFF  
SYSTEM  
BUTTONLIGHT *1  
LIGHT COLOR *1  
WL. REMOTE  
BEEP  
ON, PUSH ON, OFF  
GREEN, ORANGE, BLUE, YELLOW,  
TURQUOISE, PURPLE  
A1, A2, OFF B  
ON, OFF  
T.ZONE/DST  
See list of time zones  
D/TIME SET  
MY CAMERA  
S-UP IMAGE *3  
SHTR SOUND *2  
S-UP SOUND  
S/STOP SOUND  
SELF-T SOUND  
ON, OFF  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
1
*
, *2  
and  
, *3  
ZR65 MC  
ZR70 MC  
ZR70 MC  
ZR60  
45  
PLAY (VCR) Menu (VCR MENU)  
CAMERA  
CARD CAMERA  
Setting Options  
CARD CAMERA  
PLAY (VCR)  
Submenu  
VCR SET UP  
Menu Item  
REC MODE  
E
SP, LP  
54  
39  
93  
43  
97  
71  
71  
98  
98  
101  
102  
103  
126  
33  
134  
84  
84  
84  
51  
51  
49  
52  
25  
26  
50  
50  
50  
50  
50  
AV/PHONES  
AV, PHONES H  
ON, OFF  
AV \ DV OUT  
OUTPUT CH  
AUDIO SET UP  
L/R, L/L, R/R  
AUDIO DUB.  
WIND SCREEN  
AUDIO MODE  
12bit AUDIO  
MIX BALANCE  
AUDIO IN, MIC. IN  
ON, OFF  
16bit, 12bit  
STEREO1, STEREO2, MIX/FIXED, MIX/VARI.  
CARD SET UP *2 SI QUALITY  
MOVIE SIZE *1  
SUPER FINE, FINE, NORMAL  
320 × 240, 160 × 120  
RESET, CONTINUOUS  
CANCEL, EXECUTE  
FILE NOS.  
CARD  
COPY  
\
OPERATIONS *2  
DISPLAY SET UP BRIGHTNESS  
DISPLAYS  
ON, OFF <PLAYBK>  
6SEC. DATE  
ON, OFF  
DATA CODE  
DATE/TIME, CAMERA DATA, CAM. & D/T  
DATE, TIME, DATE & TIME  
ON, PUSH ON, OFF  
D/TIME SEL.  
SYSTEM  
BUTTONLIGHT *1  
LIGHT COLOR *1  
WL. REMOTE  
BEEP  
GREEN, ORANGE, BLUE, YELLOW,  
TURQUOISE, PURPLE  
A1, A2, OFF B  
ON, OFF  
T.ZONE/DST  
D/TIME SET  
See list of time zones  
MY CAMERA  
S-UP IMAGE*3  
SHTR SOUND *2  
S-UP SOUND  
S/STOP SOUND  
SELF-T SOUND  
ON, OFF  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
1
*
, *2  
and  
, *3  
ZR65 MC  
ZR70 MC  
ZR70 MC  
ZR60  
46  
ZR70 MC ZR65 MC  
CARD CAMERA Menu (C. CAM. MENU)  
CAMERA  
Submenu  
PLAY (VCR)  
CARD PLAY (VCR)  
CARD CAMERA  
E
Menu Item  
Setting Options  
CAMERA SET UP SHUTTER  
AUTO, 1/60, 1/100, 1/250  
78  
80  
WHITE BAL.  
SI QUALITY  
SI SIZE  
AUTO, SET W, INDOOR T, OUTDOOR U  
SUPER FINE, FINE, NORMAL  
1024 × 768, 640 × 480  
320 × 240, 160 × 120  
RESET, CONTINUOUS  
AV, PHONES H  
CARD SET UP  
101  
101  
102  
103  
39  
MOVIE SIZE *1  
FILE NOS.  
VCR SET UP  
AV/PHONES  
AUDIO SET UP *1 WIND SCREEN  
DISPLAY SET UP BRIGHTNESS  
LCD MIRROR  
ON, OFF  
71  
33  
ON, OFF  
34  
TV SCREEN  
ON, OFF  
134  
27  
D/T DISPLAY  
ON, OFF  
DEMO MODE  
ON, OFF  
53  
SYSTEM  
BUTTONLIGHT *1  
LIGHT COLOR *1  
WL. REMOTE  
BEEP  
ON, PUSH ON, OFF  
51  
GREEN, ORANGE, BLUE, YELLOW,  
TURQUOISE, PURPLE  
A1, A2, OFF B  
51  
49  
ON, OFF  
52  
T.ZONE/DST  
D/TIME SET  
See list of time zones  
25  
26  
MY CAMERA  
SHTR SOUND  
S-UP SOUND  
S/STOP SOUND  
SELF-T. SOUND  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
50  
50  
50  
50  
1
*
ZR70 MC  
47  
ZR70 MC ZR65 MC  
CARD PLAY (VCR) Menu (C.PLAY MENU)  
CAMERA  
Submenu  
CARD  
OPERATIONS  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
E
Menu Item  
COPY  
Setting Options  
CANCEL, EXECUTE  
\
127  
(Single Image  
PRINT ORDERS  
ALL ERASE  
YES, NO  
117  
Display)  
IMAGE ERASE  
FORMAT  
CANCEL, SINGLE, ALL  
115  
128  
114  
116  
54  
CANCEL, EXECUTE  
\
CARD  
OPERATIONS  
(Index Screen)  
PROTECT  
\
PRINT ORDER  
VCR SET UP  
REC MODE  
AV/PHONES  
SP, LP  
AV, PHONES H  
39  
DISPLAY SET UP BRIGHTNESS  
DISPLAYS  
33  
ON, OFF  
134  
84  
D/TIME SEL.  
DATE, TIME, DATE & TIME  
ON, PUSH ON, OFF  
SYSTEM  
BUTTONLIGHT *1  
51  
LIGHT COLOR *1  
WL. REMOTE  
BEEP  
GREEN, ORANGE, BLUE, YELLOW,  
TURQUOISE, PURPLE  
A1, A2, OFF A  
51  
49  
ON, OFF  
52  
T.ZONE/DST  
D/TIME SET  
See list of time zones  
25  
26  
MY CAMERA  
CREATE START-UP IMAGE  
130  
50  
SEL. S-UP IMG  
SHTR SOUND  
S-UP SOUND  
S/STOP SOUND  
SELF-T SOUND  
NO IMAGE, CANON LOGO, MY IMAGE  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
PATTERN1, PATTERN2, PATTERN3  
50  
50  
50  
50  
\
PRINT  
Appears when connecting a printer with direct print function.  
118  
1
*
ZR70 MC  
48  
Changing the Remote Sensor Mode  
Two remote sensor modes and an off setting are available to prevent interference  
from other Canon wireless controllers being used nearby.  
E
Turning the Remote Sensor Off  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
SYSTEM  
WL.REMOTE•••  
1
(
44)  
Open the menu and select [SYSTEM]. Select [WL.  
REMOTE], set it to [OFF B] and close the menu.  
[B] appears.  
Changing the Remote Sensor Mode  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
SYSTEM  
WL.REMOTE•••  
1
(
44)  
1. On the camcorder, open the menu and select  
[SYSTEM]. Select [WL. REMOTE], set it to [A 2] and  
close the menu.  
The selected mode appears for 4 seconds.  
2. On the wireless controller, press and hold the  
REMOTE SET button. Set the mode to the same of  
the camcorder. Press the ZOOM T button for mode 2.  
Keep the button pressed for over 2 seconds.  
AUDIO DUB. PAUSE  
SLOW  
2
AV INSERT AV DV REMOTE SET  
REC  
PAUSE  
-
WIRELESS CONTROLLER WL D79  
If you have set the camcorder to mode 1, press the ZOOM W  
button for mode 1.  
START  
/STOP  
ZOOM  
W
T
PHOTO  
SELF T. D.EFFECT.  
MENU  
SET  
ON/OFF  
TV SCREEN  
❍ The wireless controller returns to mode 1 when you replace the batteries.  
Change the mode if necessary.  
❍ Make sure that camcorder and wireless controller are set to the same mode.  
Display the camcorder’s mode by pressing any button on the wireless controller  
(except of the REMOTE SET button) and set the wireless controller’s mode to  
the same mode. Change the batteries if the wireless controller still does not  
work.  
49  
Customizing the Camcorder  
You can personalize your camcorder by customizing the start-up image and the sound  
it makes for start-up, shutter*, start/stop and self-timer (collectively called the My  
Camera settings).  
E
* ZR70 MC and ZR65 MC only. With the ZR70 MC and ZR65 MC, you can also create  
your own start-up image. See Creating a Start-up Image (  
130).  
Changing the My Camera Settings  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
(ZR60)  
MY CAMERA  
S–UP IMAGE•••ON  
(
44)  
SHTR SOUND•••PATTERN1  
S–UP SOUND•••PATTERN1  
S/STOP SOUND•PATTERN1  
SELF–T SOUND•PATTERN1  
1. Open the menu and select [MY CAMERA].  
2. Select the menu item you wish to change.  
•
When selecting a start-up image (only in CARD PLAY (VCR) mode):  
ZR70 MC ZR65 MC  
[NO IMAGE], [CANON LOGO] and [MY IMAGE] appears.  
When selecting a start-up image: [OFF] and [ON] appears.  
•
ZR60  
• When selecting a sound: [PATTERN1], [PATTERN2] and [PATTERN3] appear.  
3. Select a setting option and close the menu.  
50  
ZR70 MC  
Setting the Light-up Buttons  
The buttons above the LCD panel light up  
when the camcorder’s power is on, or when  
you press a button. This is helpful if, for  
example, you wish to play back a tape in dark  
places.  
E
You can select the color of the light-up  
buttons from green, orange, blue, yellow,  
turquoise and purple.  
MENU button  
Selector dial  
Selecting the Light-up Setting  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
SYSTEM  
BUTTONLIGHT•ON  
(
44)  
Open the menu and select [SYSTEM]. Select [BUTTONLIGHT], set it to  
[PUSH ON] or [OFF] and close the menu.  
• ON: The buttons light up while the camcorder is turned on. The color changes when you  
press a button and turns back when you release the button.  
• PUSH ON: The buttons light up when you press a button and turn off when you release  
the button.  
• OFF: Buttons do not light up.  
Selecting the Color of the Buttons  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
SYSTEM  
LIGHT COLOR•TURQUOISE  
(
44)  
Open the menu and select [SYSTEM]. Select [LIGHT COLOR], set it to the  
desired color and close the menu.  
You cannot change the color of the buttons when [BUTTONLIGHT] is set to [OFF].  
51  
Other Camcorder Settings  
Beep  
E
You will hear a beep upon camcorder operations such as power on/off, start/stop, self-  
timer countdown, automatic shut-off, and unusual conditions of the camcorder. The  
beep will not be recorded.  
If you turn off the beep, all camcorder sounds including the ones of the My Camera  
settings will be turned off.  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
SYSTEM  
BEEP•••••••••ON  
(
44)  
To turn the beep off, open the menu and select [SYSTEM]. Select [BEEP],  
set it to [OFF] and close the menu.  
Recording in 16:9 (Wide Screen TV Recording)  
You can record in the 16:9 format for playback on wide screen TVs.  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
CAMERA SET UP  
16:9••••••••OFF  
(
44)  
To switch 16:9 on, open the menu and select [CAMERA SET UP]. Select  
[16:9], set it to [ON] and close the menu.  
”16:9” appears.  
❍ The 16:9 mode cannot be selected in the Easy Recording mode.  
❍ The multi-image screen cannot be used when the 16:9 format is selected.  
❍ If you play back a 16:9 recording on a normal TV, the image appears vertically  
“squashed” (compressed).  
❍ If you connect the camcorder to a TV with an S1 terminal or Video ID-1  
system, recordings made in the 16:9 mode will be automatically played back in  
wide screen mode.  
52  
Demonstration Mode  
The demonstration mode displays the camcorder’s main features. It starts  
automatically when you leave the camcorder turned on without loading a cassette  
(ZR70 MC/ZR65 MC: and without inserting a memory card) for more than 5 minutes.  
You can also start the demonstration mode through the menu.  
E
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
DISPLAY SET UP  
DEMO MODE•••ON  
(
44)  
With no cassette (ZR70 MC/ZR65 MC: and memory card) inserted, open the  
menu and select [DISPLAY SET UP]. Select [DEMO MODE], set it to [OFF]  
and close the menu.  
To cancel the demo mode, press any button, turn off the camcorder, load a cassette  
(ZR70 MC/ZR65 MC: or insert a memory card).  
53  
Changing the Recording Mode (SP/LP)  
You can choose from SP (standard play) and LP (long play). LP extends the tape usage  
by 1.5 times.  
E
❍ Tapes recorded in LP mode cannot be used for audio dubbing (  
insert ( 94).  
96) or AV  
❍ Depending on the nature and usage condition of the tape, picture and sound  
recorded in LP mode may be distorted. We recommend using the SP mode for  
important recordings.  
❍ We recommend recording in SP mode if you plan to transfer the images to a  
computer.  
❍ If you record in both SP and LP modes on the same tape, the playback picture  
may become distorted and the time code may not be written correctly.  
❍ If you play back a tape that has been recorded in LP mode with another digital  
device on this camcorder, or vice versa, picture and sound may become  
distorted.  
CARD CAMERA  
CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
VCR SET UP  
REC MODE••••SP  
(
44)  
To change to LP mode, open the menu and select [VCR SET UP]. Select  
[REC MODE], set it to [LP] and close the menu.  
54  
Recording Still Images on the Tape  
You can record still images on the tape. Starting your recording with a still image  
allows you to easily locate the beginning of the recording with the Photo Search  
E
function (  
85).  
PHOTO button  
PHOTO button  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
In Record Pause Mode  
1. Press the PHOTO button halfway.  
• Autofocus: F flashes in white and turns green when focus is  
adjusted.  
P
H
O
T
O
• Manual focus: F flashes in green. Adjust the focus with the  
selector dial.  
• Exposure is locked.  
• When you press the PHOTO button on the wireless controller, recording starts  
immediately.  
2. Press the PHOTO button fully.  
• F disappears.  
• The camcorder records the still image for approx. 6 seconds.  
P
H
O
T
O
During this time, the camcorder displays the still image and  
keeps recording the sound.  
• The camcorder returns to record pause mode.  
During Recording  
1. Press the PHOTO button fully.  
• The camcorder records the still image for approx. 6 seconds.  
During this time, the camcorder displays the still image and  
P
H
O
T
O
keeps recording the sound  
• The camcorder returns to record pause mode.  
55  
❍ When you turn the POWER switch to OFF while the camcorder is recording the  
still image, it will not turn off until recording is complete.  
❍ Record still images under sufficient lighting condition (in which you can identify  
the subject on the screen).  
❍ If a subject is unsuitable for autofocus, F continues to flash. Keep the PHOTO  
button pressed halfway and adjust the focus with the selector dial.  
E
56  
Using the Recording Programs  
The camcorder is equipped with the Easy Recording program and several program AE  
modes. The availability of functions differs depending on the selected mode.  
E
Availability of Functions in Each Mode:  
Position of the  
Program Selector  
[
Q
1
1
*
*
Recording Program  
[
h
Digital Zoom  
Shutter Speed  
Focus  
h
×
h
A
h
h
h
A
White Balance  
AE Shift  
Image Stabilizer*2  
Digital Effects  
16:9  
ON  
×
h
h
×
×
h*4  
×
h
Card Mix*3  
×
A: Auto setting h: Available ×: Not available  
*1 ZR70 MC only.  
*2 The image stabilizer cannot be used in CARD CAMERA mode.  
*3 ZR70 MC and ZR65 MC only.  
*4 Available effects depend upon the program AE mode.  
Easy Recording Program  
The camcorder adjusts focus, exposure and other settings  
[
automatically, allowing you to just point and shoot.  
Program AE Modes  
Auto  
The camcorder adjusts focus, exposure and other settings  
automatically. However, you have the option of adjusting the  
settings manually.  
57  
Sports  
Use this mode to record sports scenes (such as tennis or golf),  
moving objects (such as roller coasters) or when recording from a  
moving car.  
E
❍ This mode is set at a high shutter speed and should therefore be used in sufficient  
light.  
❍ This mode is mainly intended for frame-by-frame or slow playback. The picture may  
not appear smooth when played back in normal speed.  
Portrait  
Use this mode to give accent to your subject by blurring the  
background or foreground.  
❍ The blur effect increases the more you zoom to telephoto.  
❍ This mode is set at a higher shutter speed. The picture may not  
appear smooth when played back.  
Spotlight  
Use this mode to record spotlit scenes such as shows, recitals or  
fireworks.  
Sand & Snow  
Use this mode in bright places such as a sunny beach or ski resort. It  
prevents the subject from being underexposed.  
❍ The subject may become overexposed in dark surroundings. Check  
the image on the screen.  
❍ This mode is set at a higher shutter speed. The picture may not appear smooth when  
played back.  
Low Light  
Use this mode to record in dimly lit places. The shutter is fixed at a  
slow shutter speed.  
❍ Moving subjects may leave a trailing afterimage.  
❍ Picture quality may not be as good as in other modes.  
❍ The camcorder may have difficulty to focus automatically.  
58  
Night  
Use this mode to record in dark places. The shutter speed is  
adjusted automatically. It is useful when recording in places with  
changing light conditions (such as in amusement parks).  
E
ZR70 MC ZR65 MC  
❍
Night mode cannot be used in CARD CAMERA  
mode.  
❍ Moving subjects may leave a trailing afterimage.  
❍ Picture quality may not be as good as in other modes.  
❍ White points may appear on the screen.  
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus  
manually.  
ZR70 MC  
Super Night (CAMERA mode)  
In CAMERA mode, use this mode to record in very dark places. The  
shutter speed is adjusted automatically. The White LED lights up  
automatically illuminating the subject in the center of the screen,  
allowing you to record brightly in color.  
Low Light Plus (CARD CAMERA mode)  
In CARD CAMERA mode, use this mode to record in dark places.  
The shutter is fixed at a slow shutter speed. The White LED lights up  
illuminating the subject in the center of the screen, allowing you to  
record brightly in color.  
❍ The range of the White LED is limited. Check the image on the screen when  
recording.  
❍ Use this mode for recordings at close range (up to 6.6 ft (2m)).  
❍ Moving subjects may leave a trailing afterimage.  
❍ Picture quality may not be as good as in other modes.  
❍ White points may appear on the screen.  
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus  
manually.  
59  
Selecting the Program AE Mode  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
E
1. Slide the program selector to Q (program AE).  
2. Press the selector dial.  
A list of the program AE modes appears.  
3. Select a mode and press the selector dial.  
The symbol of the mode appears on the upper left corner of the  
screen.  
(Auto) disappears after 4 seconds.  
❍ Do not change the mode during recording as the brightness of the image may  
change abruptly.  
❍ The setting resets to the Auto mode when you switch the program selector to  
[.  
❍ Bright light in a dark scene may cause a vertical light bar to appear. This is not  
a malfunction.  
60  
Using Digital Effects  
You can use the digital effects during recording and playback.  
E
Faders (  
Effects (  
62): Begin or end scenes with a fade to or from black.  
65): Add flavor to your recordings.  
Multi-image screen (  
67)  
Availability of Digital Effects by Operating Modes:  
CAMERA  
ZR70 MC/ZR65 MC: ZR70 MC/ZR65 MC:  
CARD CAMERA CARD PLAY (VCR)  
PLAY (VCR)  
Movies Still Images  
Faders  
Effects  
h
h
i
h
h
h
i
i
i
h*1  
Multi-image  
screen  
h*2  
h*2  
h
i
i
h: Available i: Not available  
*1: Black and White only  
*2: Cannot be used in Night and Super Night (ZR70 MC) mode.  
❍ Turn off the digital effect when you do not use it.  
Press the DIGITAL EFFECTS button to open the menu. Select [D.EFFECTS |]  
and press the ON/OFF button.  
❍ The camcorder retains the setting even if you turn it off or change the program  
AE mode.  
❍ The digital effect turns off if you switch the program selector to [.  
❍ Digital effects can be selected but not activated on a blank blue screen  
(appears in PLAY (VCR) mode).  
❍ Digital effects activated during playback do not change the recording.  
❍ Digital effects cannot be used during DV dubbing and photo/date search.  
❍ Digital effects can also be set with the wireless controller.  
61  
Faders  
Fade Trigger (FADE-T)  
The image gradually fades in.  
E
The image gradually fades out.  
Wipe (WIPE)  
The image begins as a vertical  
line in the center and  
expands sideways until  
it fills the whole screen.  
The image is wiped off from the  
sides of the screen.  
Corner Wipe (CORNER)  
The image appears from the  
corners until it fills the  
whole screen.  
The image is wiped off from the  
corners.  
Jump (JUMP)  
A small image appears from  
the left, jumps into the  
center and enlarges  
until it fills the whole  
screen.  
The image shrinks, jumps from  
the center to the left and  
disappears.  
Flip (FLIP)  
The image flips into the screen.  
The image flips out of the screen.  
62  
Puzzle (PUZZLE)  
The image appears in 16 pieces.  
The pieces move  
around until the  
E
puzzle is solved.  
The image is divided into 16  
pieces. The pieces move around  
and disappear.  
Zigzag (ZIGZAG)  
The image appears in zigzag  
from the top of the  
screen.  
Black stripes appear in zigzag  
from the bottom of the screen  
until they cover the whole image.  
Beam (BEAM)  
The screen turns yellow, forms  
a beam that becomes  
thinner and the image  
appears.  
A yellow beam appears in the  
center of the screen and expands  
until it covers the whole image.  
Tide (TIDE)  
The image appears from  
both sides like tides.  
The image disappears from both  
sides like tides.  
63  
Selecting a Fader  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
PLAY (VCR)  
E
1. In CAMERA mode, set the program selector to Q.  
2. Press the DIGITAL EFFECTS button.  
DIGITAL  
EFFECTS  
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.  
3. Select [FADER].  
4. Select the fader option.  
5. Press the DIGITAL EFFECTS button.  
The name of the selected fader flashes.  
CAMERA mode:  
6. Fade in: In record pause mode, press the ON/OFF  
button and begin recording by pressing the  
start/stop button.  
ON/OFF  
Fade out: During recording, press the ON/OFF button  
and pause recording by pressing the start/stop button.  
The fader can be activated/deactivated by pressing the ON/OFF button.  
PLAY (VCR) mode:  
6. Fade in: In playback pause mode, press the ON/OFF  
button and begin playback by pressing the e/a  
button.  
ON/OFF  
Fade out: During playback, press the ON/OFF button  
and pause playback by pressing the e/a button.  
The fader can be activated/deactivated by pressing the ON/OFF button.  
ZR70 MC ZR65 MC  
Faders cannot be selected when Card Mix is activated.  
64  
Effects  
Art (ART)  
The image becomes like a paint (solarization).  
E
Black and White (BLK & WHT)  
The image becomes black and white.  
Sepia (SEPIA)  
The image becomes monochrome with a brownish tint.  
Mosaic (MOSAIC)  
The image is blurred through enlarging the size of some pixels.  
Ball (BALL)  
The image becomes like a ball.  
Cube (CUBE)  
The image becomes a cube and rotates.  
Wave (WAVE)  
Both ends of the image sway in waves.  
Color Masking (COLOR M.)  
The image becomes a rhombus surrounded by a masking frame that  
changes the colors.  
Mirror (MIRROR)  
Creates a symmetrical image as if there would be a mirror in the  
center of the screen.  
ZR70 MC ZR65 MC  
Only Black and White can be used in CARD CAMERA mode.  
65  
Selecting an Effect  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
PLAY (VCR)  
E
1. Press the DIGITAL EFFECTS button.  
DIGITAL  
EFFECTS  
[D.EFFECTS OFF], [FADER], [EFFECT] and [MULTI-S] appear.  
2. Select [EFFECT].  
3. Select the effect.  
4. Press the DIGITAL EFFECTS button.  
DIGITAL  
EFFECTS  
The name of the selected effect flashes.  
5. Press the ON/OFF button.  
ON/OFF  
• The name of the selected effect stops flashing.  
• The effect can be activated/deactivated by pressing the ON/OFF  
button.  
ZR70 MC ZR65 MC  
Selecting an Effect in CARD CAMERA Mode  
CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
CARD CAMERA  
1. Press the DIGITAL EFFECTS button.  
DIGITAL  
EFFECTS  
“BLK&WHT” flashes.  
2. Press the ON/OFF button.  
ON/OFF  
• “BLK&WHT” stops flashing.  
• The effect can be activated/deactivated by pressing the ON/OFF  
button.  
66  
Using the Multi-Image Screen  
The multi-image screen captures moving subjects in 4, 9 or 16 sequences of still images  
with the Image Capture feature and displays them at one time. Sound will be  
recorded normally. This feature can be used in CAMERA and PLAY (VCR) mode.  
You can choose the transition speed at which to capture the subject from manual, fast  
(every 4 frames), moderate (every 6 frames*) or slow (every 8 frames*).  
E
* In Low Light mode: moderate (every 8 frames), slow (every 12 frames).  
Selecting the Multi-Image Screen  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
PLAY (VCR)  
1. Set the program selector to Q.  
2. Press the DIGITAL EFFECTS button.  
DIGITAL  
EFFECTS  
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.  
3. Select [MULTI-S].  
[S.SPEED] and [S.SPLIT] appears.  
4. Select [S.SPEED].  
[MANUAL], [FAST], [MOD.] and [SLOW] appear.  
5. Select the transition speed.  
6. Select [MULTI-S] again.  
[S.SPEED] and [S.SPLIT] appears.  
7. Select [S.SPLIT].  
[4], [9], [16] settings appear.  
8. Select the number of sequences.  
9. Press the DIGITAL EFFECTS button.  
[MULTI-S] flashes.  
DIGITAL  
EFFECTS  
67  
Capturing  
10.Press the ON/OFF button.  
• MANUAL: Images will be captured each time you press the ON/OFF button. The blue  
frame indicating the next sequence disappears after the last image. To cancel the last  
captured image, press and hold the ON/OFF button. To cancel the multi-image screen,  
press and release the ON/OFF button.  
E
• FAST, MODERATE, SLOW: The set number of images will be captured at the set speed.  
To cancel the multi-image screen, press the ON/OFF button.  
11.Press the start/stop button begin recording.  
The multi-image screen is recorded on the tape.  
❍ The multi-image screen cannot be operated in Night and Super Night (ZR70  
MC) mode.  
❍ You can operate the multi-image screen only in the following playback modes:  
-
When [S.SPEED] is set to [MANUAL]: Playback pause, slow forward/reverse  
playback  
-
When [S.SPEED] is set to [FAST], [MOD.] or [SLOW]: Playback pause  
❍ The multi-image screen can be operated in record or record pause mode.  
ZR70 MC ZR65 MC  
❍
The multi-image screen cannot be selected when Card Mix is  
activated.  
❍ In PLAY (VCR) mode: Pressing any tape operation button (such as play or  
pause), or performing date/photo search cancels the multi-image screen.  
68  
Turning Off the Image Stabilizer  
The image stabilizer allows you to obtain steady recordings even at telephoto. There is  
no need to turn off the image stabilizer during normal recording. However, the  
camcorder tries to compensate for horizontal movements and you may therefore  
decide to turn it off during panning. The image stabilizer cannot be turned off when  
the program selector is set to [.  
E
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
CAMERA SET UP  
IMAGE S.  
••ON  
(
44)  
Open the menu and select [CAMERA SET UP]. Select [IMAGE S. i], set it  
to [OFF] and close the menu.  
i disappears.  
❍ We recommend turning off the image stabilizer when you mount the  
camcorder on a tripod.  
❍ The image stabilizer is designed to compensate a normal degree of camcorder  
shake.  
ZR70 MC ZR65 MC  
❍
The image stabilizer cannot be used in CARD CAMERA  
mode.  
❍ The image stabilizer might not be as effective in Low Light, Night and Super  
Night (ZR70 MC) mode.  
69  
Recording With the Self-Timer  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
E
PHOTO  
button  
(self-timer)  
button  
Start/stop button  
SELF T. button  
PHOTO button  
Start/stop button  
1. Press the  
” appears.  
(self-timer) button.  
DATA  
CODE  
“
When recording movies  
2. Press the start/stop button.  
The camcorder starts recording after a 10-second countdown (2  
seconds when using the wireless controller). The count down  
appears on the screen.  
A
R
E
M
A
C
FF  
OFF  
Y
LA  
P
)
R
C
(VVCR)  
3. Press the start/stop button to stop recording.  
The camcorder returns to record pause mode  
When recording still images  
2. Press the PHOTO button.  
• The camcorder adjusts the focus 2 seconds before recording  
begins. F flashes in white and turns green when focus and  
exposure are adjusted.  
P
H
O
T
O
• The camcorder records the still image for approx. 6 seconds  
and returns to record pause mode (ZR70 MC/ZR65 MC: In CARD CAMERA mode, it  
displays the still image when recording is complete).  
❍ To cancel the self-timer, press the  
(self-timer) button, start/stop button  
(when recording movies) or PHOTO button (when recording still images).  
❍ The self-timer will be canceled when you turn off the camcorder.  
70  
Audio Recording  
Changing the Audio Mode  
E
You can record sound in two audio modes—16-bit and 12-bit. The 12-bit mode records  
sound on two channels (stereo 1), leaving 2 channels free (stereo 2) for adding new  
sound later. Select the 16-bit mode for higher sound quality.  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
PLAY (VCR)  
AUDIO SET UP  
AUDIO MODE••12bit  
(
44)  
Open the menu and select [AUDIO SET UP]. Select [AUDIO MODE], set it to  
[16bit] and close the menu.  
“16 bit” appears for approximately 4 seconds.  
For adding new sound, see Audio Dubbing (  
96).  
Recording with an External Microphone  
You can use an external microphone for  
recording. Almost all stereo microphones with  
a plug diameter of 0.14 inch (3.5 mm) can be  
connected to the MIC terminal. Use a  
MIC  
microphone with a built-in power supply  
(condenser microphone).  
❍ The audio level differs from that of the built-in microphone.  
❍ Be careful with long microphones as they may appear in the picture.  
ZR70 MC  
❍
See also Using the DM-50 Microphone (  
74).  
Wind Screen  
You can reduce the wind noise when recording in windy places.  
CARD PLAY (VCR)  
CAMERA  
PLAY (VCR) CARD CAMERA  
AUDIO SET UP  
WIND SCREEN•OFF  
(
44)  
Open the menu and select [AUDIO SET UP]. Select [WIND SCREEN], set it  
to [ON] and close the menu.  
“WS ON” appears when you turn the wind screen on.  
71  
❍ Low sound may be reduced together with the wind noise. We recommend  
turning off the wind screen for normal recordings.  
❍ The wind screen function cannot be turned on/off during recording.  
❍ The wind screen function can also be used for audio dubbing (when [AUDIO  
DUB.] is set to [MIC. IN] in the [AUDIO SET UP] submenu).  
E
❍ The wind screen function cannot be used when an external microphone is  
connected to the MIC terminal (ZR70 MC: or when the DM-50 Microphone is  
attached to the advanced accessory shoe).  
72  
ZR70 MC  
Using the VL-3 Video Light (Optional)  
This video light enables you to record brightly in color even in dark places. This VL-3  
Video Light attaches to the camcorder’s advanced accessory shoe for cable-free  
E
operation and is powered by the camcorder’s power supply.  
Refer also to the VL-3 Video Light instruction manual.  
❍ Always turn off the camcorder before attaching/removing the video light.  
❍ Do not touch or place flammable material or plastic close to the lamp or the  
surrounding parts during or immediately after use; they become very hot.  
❍ Do not look directly at the lamp while the video light is on.  
❍ Do not carry the camcorder by the video light.  
1. Slide the video light into the  
accessory shoe until it clicks.  
K
C
LO  
q
2. Tighten the fastening screw.  
Be careful that the video light does not come  
off when tightening the screw.  
3. Set the camcorder to CAMERA or  
CARD CAMERA mode.  
e
4. Turn the video light’s power switch  
A
ER  
M
CA  
to AUTO or ON.  
w
FF  
O
AY  
PL  
)
CR  
(VCR)  
•
(Connection) appears.  
K
C
O
L
• ON: The video light stays on.  
• AUTO: The video light turns on and off  
automatically.  
CK  
LO  
r
O
T
N
U
O
A
F
F
O
L
O
C
K
73  
ZR70 MC  
Using the DM-50 Microphone (Optional)  
The high sensitive Directional Stereo Microphone DM-50 attaches to the  
advanced accessory shoe for cable-free operation and is powered by the camcorder’s  
power supply. Use it for recording or dubbing audio.  
E
Refer also to the DM-50 Microphone instruction manual.  
❍ Always turn the camcorder off before attaching/removing the microphone.  
❍ Do not connect any microphone to the MIC terminal when the DM-50  
Microphone is connected.  
❍ Do not carry the camcorder by the microphone.  
1. Slide the microphone into the  
accessory shoe until it clicks.  
2. Tighten the fastening screw.  
q
Be careful that the microphone does not  
come off when tightening the screw.  
3. Set the camcorder to CAMERA or  
CARD CAMERA mode.  
e
(Connection) appears.  
A
ER  
M
CAAMERA  
4. Set the microphone’s directivity  
switch.  
FF  
O
AY  
PL  
)
CR  
(V  
• SHOTGUN: For recording clear sound from  
the front (monaural).  
• STEREO 1: For recording sound from the  
front and surrounding area.  
• STEREO 2: For recording surrounding  
sound in a wider range than in  
STEREO 1.  
r
w
74  
Adjusting the Focus Manually  
Some subjects may not be suitable for autofocus. In such case, focus manually.  
E
Autofocus may not work well on the following subjects:  
Subjects with  
Reflective surfaces  
low contrast  
(e.g. White Wall)  
Fast Moving Subjects Horizontal Stripes  
Through dirty or  
wet windows  
Different Distances  
Dark Subjects  
Night Scenes  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
1. Set the program selector to Q.  
2. Adjust the zoom.  
When you operate the zoom after adjusting the focus, the  
subject may not stay in focus. Adjust the zoom before the focus.  
3. Press the FOCUS button.  
FOCUS  
“MF” appears in light blue.  
4. Turn the selector dial to adjust the focus.  
• Turn the selector dial up or down until the image appears  
focused.  
• If “AE 0” appears in light blue, focus cannot be adjusted.  
Press the FOCUS button again to display “MF” in light blue.  
75  
5. Press the FOCUS button to return to autofocus.  
FOCUS  
E
The setting resets to autofocus when you switch the program selector to [.  
Infinity Focus  
Use this function when you wish to focus on faraway subjects such as mountains or  
fireworks.  
Press the focus button more than 3 seconds in step 3.  
“MF ∞” appears. When you operate the zoom or turn the selector dial when “MF ∞” is  
displayed in light blue, “∞” disappears and the camcorder changes to manual focus.  
76  
Adjusting the AE Shift  
You can adjust the AE (auto exposure) function to lighten or darken the image. This  
allows you to compensate for backlit or overexposed scenes. Available Levels: –2 to +2,  
in 0.25 intervals (excluding –1.75 and +1.75).  
E
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
1. Set the program selector to Q.  
2. Set the program AE mode to  
Auto,  
Sports,  
Portrait,  
Low  
Light or  
Low Light Plus (ZR70 MC) mode.  
3. Press the AE SHIFT button.  
AE SHIFT  
“AE 0” appears in light blue.  
4. Turn the selector dial to adjust the AE shift level.  
• Turn the selector dial up to lighten the image and down to  
darken the image.  
• If “MF” is displayed in light blue, AE shift cannot be adjusted.  
Press the AE SHIFT button again to display “AE 0” in light blue.  
❍ The camcorder retains the setting even if you turn it off or change the program  
AE mode.  
❍ The camcorder resets to the auto setting when you switch the program  
selector to [.  
77  
Setting the Shutter Speed  
In the  
Auto mode, you can adjust the shutter speed manually to make stable shots  
E
of fast moving subjects.  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
CAMERA SET UP  
SHUTTER•••••AUTO  
(
44)  
1. Set the program selector to Q.  
2. Set the program AE mode to the  
(AUTO) mode.  
3. Open the menu and select [CAMERA SET UP].  
4. Select [SHUTTER].  
5. Select the shutter speed and press the selector dial.  
ZR70 MC ZR65 MC  
,
CAMERA Mode  
CARD CAMERA Mode  
AUTO  
1/60  
AUTO  
1/60  
1/100  
1/250  
1/500  
1/1000  
1/2000  
1/100  
1/250  
6. Close the menu.  
❍ Do not point the camcorder directly at the sun when the shutter speed is set to  
1/1000 or higher.  
❍ The image may flicker when recording with high shutter speeds.  
❍ The setting resets to the auto setting when you switch the program selector to  
[, or change the program AE mode.  
ZR70 MC ZR65 MC  
❍
If the shutter speed is set to 1/500 or higher in CAMERA  
mode and you switch to CARD CAMERA mode, it automatically changes to  
1/250.  
❍ Recording under fluorescent lights: When the camcorder is set to [ (Easy  
Recording) or when the program AE mode is set to Auto, Night or Super Night  
(ZR70 MC) mode, it automatically detects the flicker of fluorescent lighting and  
adjusts the shutter speed accordingly. However, if the brightness of the screen  
starts to flicker, select Auto mode and set the shutter speed to 1/100.  
78  
❍ Guidelines for Recording with High Shutter Speeds:  
-
-
-
Outdoor sports such as golf or tennis: 1/2000  
E
Moving objects such as cars or roller coasters: 1/1000,  
1/500 or 1/250  
Indoor sports such as basketball: 1/100  
79  
Setting the White Balance  
The camcorder’s auto white balance system adjusts the colors to appear natural for  
different lighting conditions. However, you can use the preset modes to reproduce  
colors more accurately, or set a custom white balance to obtain the optimal setting.  
E
Zoom lever  
White sheet or paper  
Program selector  
Selector dial  
❍ When the program selector is set to [, white balance is preset to [AUTO].  
Indoor, outdoor and custom white balance cannot be selected.  
❍ The camcorder retains the setting even if you turn it off.  
❍ When you have set the custom white balance:  
-
-
Reset the white balance when the lighting condition changes.  
Turn off the digital zoom.  
❍ Setting the white balance manually may provide better results in the following  
cases.  
-
-
-
-
Changing lighting conditions  
Close-ups  
Subjects in a single color (sky, sea or forest)  
Under mercury lamps or certain types of fluorescent lights  
❍ Use the T Indoor or U Outdoor mode in the following cases:  
T Indoor:  
-
-
-
Changing lighting condition  
Under video light  
Under sodium lamps  
U Outdoor Mode  
-
-
For night scenes or fireworks  
Sunrise or sunset  
* Use the auto setting for normal outdoor scenes.  
80  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
CAMERA SET UP  
WHITE BAL.••AUTO  
E
(
44)  
For T (Indoor) or U (Outdoor) Setting:  
1. Set the program selector to Q.  
2. Open the menu and select [CAMERA SET UP].  
3. Select [WHITE BAL.].  
4. Select T (indoor) or U (outdoor).  
T or U appears.  
5. Close the menu.  
For Custom White Balance:  
1. Set the program selector to Q.  
2. Open the menu and select [CAMERA SET UP].  
3. Select [WHITE BAL].  
4. Point the camcorder at a white object (such as a sheet of paper), zoom  
in until it fills the whole screen and select [SET W].  
• W flashes and stops flashing when settings is complete.  
• Depending on the light source, W may keep flashing. The result will still be better  
than with the auto setting.  
5. Close the menu.  
81  
Magnifying the Image  
The playback image can be magnified by 2 times.  
E
CAMERA  
CARD CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
1. Move the zoom lever toward T.  
• The image is magnified by 2 times.  
• A frame appears indicating the position of the enlarged part.  
2. Move the image.  
• Turn the selector dial to move the image to the right and left,  
or up and down. Pressing the selector dial switches between  
the directions.  
• To cancel the magnification, move the zoom lever toward W.  
ZR70 MC  
Movies played back from a memory card cannot be magnified.  
82  
Displaying the Data Code  
Once date and time are set, the camcorder maintains a data code containing  
recording date and time and other camera data such as shutter speed and exposure  
(f-stop). (ZR70 MC/ZR65 MC: Only date and time appear when playing back a memory  
card).  
E
DATA CODE button  
Controller buttons  
MENU button  
DATA CODE  
button  
MENU button  
Selector dial  
❍ The data code display turns off when you turn the camcorder off.  
❍ The data code may not be displayed if a recording made with this camcorder is  
played back on a different digital camcorder.  
❍ The data code cannot be displayed in frame advance/reverse playback. Camera  
data may not appear in some special playback modes.  
❍ When the TV screen displays are hidden (  
134), the displays still appear on  
the LCD screen. If you turn on the data code, displays other than the data  
code will disappear from the LCD screen.  
Available Data Code Combinations (in PLAY (VCR) mode):  
DATA CODE  
Date/Time &  
Camera data  
(tape only)  
Date/Time  
Camera data  
D/TIME SEL.  
F1.8  
Date  
Time  
F1.8  
1/250  
JAN. 1,2003  
1/250  
JAN. 1,2003  
F1.8  
F1.8  
1/250  
1/250  
12:00:00 PM  
12:00:00 PM  
F1.8  
1/250  
12:00 PM  
JAN. 1,2003  
12:00 PM  
JAN. 1,2003  
Date & Time  
F1.8  
1/250  
83  
Selecting the Date/Time Display Combination  
CAMERA  
CARD CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
E
DISPLAY SET UP  
D/TIME SEL.•DATE & TIME  
(
44)  
Open the menu and select [DISPLAY SET UP]. Select [D/TIME SEL.], set it to  
[DATE] or [TIME] and close the menu.  
Selecting the Data Code Display Combination  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
DISPLAY SET UP  
DATA CODE•••DATE/TIME  
(
44)  
Open the menu and select [DISPLAY SET UP]. Select [DATA CODE], set it to  
[DATE/TIME], [CAMERA DATA] or [CAM. & D/T] and close the menu.  
Displaying the Data Code  
CAMERA  
CARD CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
Press the DATA CODE button.  
Only date and time appear in CARD PLAY (VCR) mode.  
Six-Second Auto Date  
Date and time appear for 6 seconds when you begin playback, or to indicate that date  
or time zone has changed.  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
DISPLAY SET UP  
6SEC.DATE•••OFF  
(
44)  
Open the menu and select [DISPLAY SET UP]. Select [6SEC.DATE], set it to  
[ON] and close the menu.  
84  
Photo Search/Date Search  
You can search for a still image recorded  
anywhere on the tape with the photo search  
function, or locate the change of the  
E
SEARCH SELECT button  
Search buttons  
date/time zone with the date search function.  
STOP 3 button  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
1. Press the SEARCH SELECT button to choose between  
photo search and date search.  
INDEX SLIDE SHOW  
CARD  
DATA CODE SEARCH SELECT  
ZERO SET  
REW  
PLAY  
STOP  
FF  
MEMORY  
“PHOTO SEARCH” or “DATE SEARCH” appears.  
12bit  
AUDIO OUT  
2. Press the + or - button to begin searching.  
INDEX SLIDE SHOW  
CARD  
DATA CODE SEARCH SELECT  
ZERO SET  
• Press the + button to search forward and the - button to  
search backward.  
REW  
PLAY  
STOP  
FF  
MEMORY  
12bit  
AUDIO OUT  
• Press more than once to search for further still images or date  
changes (up to 10 times).  
• Press the + or - button to change the search direction.  
• Press the 3 (stop) button stop searching.  
❍ Photo search: A still image recorded very close to the point you start the search  
may not be detected.  
❍ Date search: A recording of longer than a minute per date/area is required.  
❍ Date search: Playback may start slightly before or after the date change.  
❍ Date search may not function if the data code is not correctly displayed.  
85  
Returning to a Pre-marked Position  
If you wish to return to a particular scene  
later, mark the point with the zero set  
E
REW ` button  
memory and the tape will stop at that point  
when you rewind/fast forward the tape.  
PLAY e button  
FF 1 button  
ZERO SET  
MEMORY  
button  
STOP 3 button  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
PLAY (VCR)  
1. Press the ZERO SET MEMORY button at the point  
you wish to return to later.  
INDEX SLIDE SHOW  
CARD  
DATA CODE SEARCH SELECT  
ZERO SET  
REW  
PLAY  
STOP  
FF  
MEMORY  
• “0:00:00 ” appears.  
12bit  
AUDIO OUT  
• To cancel, press the ZERO SET MEMORY button again.  
2. When you have finished playback, fast forward or  
rewind the tape.  
• “RTN 1” or “` RTN” appears.  
• The tape stops automatically at “0:00:00”.  
• The tape counter changes to time code.  
❍ Time code and tape counter display may not match accurately.  
❍ The zero set memory may not function correctly when blank sections exist on  
the tape.  
❍ If you remove the tape, the zero set memory is canceled and the counter  
display shows the time code.  
86  
Recording to a VCR or Digital Video Device  
You can copy your recordings by connecting the camcorder to a VCR or a digital video  
device. If you connect a digital video device, you can copy recordings with virtually no  
generation loss in image and sound quality.  
E
When connecting a VCR:  
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change  
the setting (  
39).  
❍ The quality of the edited tape will be slightly lower than that of the original.  
When connecting a digital video device:  
❍ You can connect only one device to the camcorder with the DV cable.  
❍ Blank sections may be recorded as anomalous picture.  
❍ If the picture does not appear, reconnect the DV cable or turn the camcorder  
off and back on again.  
Example: Recording to a VCR  
CAMERA  
CARD CAMERA  
CARD CAMERA  
PLAY (VCR)  
1. Connect the camcorder to the VCR.  
See Playing Back on a TV Screen ( 41).  
2. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.  
3. Connected device: Load a blank cassette and set the device to record  
pause mode.  
4. Locate the scene you wish to copy and pause playback shortly before  
the scene.  
5. Play back the tape.  
6. Connected device: Begin recording when the scene you wish to copy  
appears. Stop recording when copying is complete.  
7. Stop playback.  
87  
Connecting a Digital Video Device  
Refer also to the instruction manual of the digital video device.  
E
Side with an arrow  
Signal flow  
Commercially available DV cable  
88  
Recording from Analog Video Devices (VCR, TV or Camcorder)  
You can record videos or TV programs from a VCR or analog camcorder on the tape in  
the camcorder.  
E
❍ Anomalous signals sent from the connected device may be recorded as  
anomalous picture (although it may not appear so on the screen), or it may not  
be recorded at all.  
❍ You cannot record from tapes with copyright protective signals.  
❍ Headphones cannot be used during analog line-in recording. If the  
AV/headphones terminal set to [PHONES H], it will automatically switch to [AV].  
CAMERA  
CARD CAMERA  
CARD CAMERA  
PLAY (VCR)  
1. Connect the camcorder to the analog video device.  
See Playing Back on a TV Screen ( 41).  
2. Set the camcorder to PLAY (VCR) mode and load a blank cassette.  
3. Connected device: Load the recorded cassette.  
4. Press the REC PAUSE button on the wireless  
AV INSERT AV DV REMOTE SET  
controller.  
REC  
PAUSE  
-
WIRELESS CONTROLLER WL D79  
In record pause mode and during recording, you can check the  
picture on the screen.  
5. Connected device: Play back the tape.  
6. Press the PAUSE a button on the wireless controller  
when the scene you wish to record appears.  
ZERO SET  
REW  
PLAY  
STOP  
SLOW  
FF  
MEMORY  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
AV INSERT AV DV REMOTE SET  
7. Press the STOP 3 button on the wireless controller to  
stop recording.  
ZERO SET  
MEMORY  
REW  
PLAY  
STOP  
SLOW  
FF  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
• Press the PAUSE a button on the wireless controller to pause  
recording.  
AV INSERT AV DV REMOTE SET  
• Press the PAUSE a button again to restart recording.  
8. Connected device: Stop playback.  
89  
Recording from Digital Video Devices (DV Dubbing)  
You can record from other digital video devices equipped with a DV terminal with  
virtually no loss in picture and sound quality.  
E
❍ When recording from digital video devices, make sure that “AV \ DV” is not  
displayed on the screen. If “AV \ DV” is displayed, change the setting  
(
93).  
❍ Anomalous signals sent from the connected device may be recorded as  
anomalous picture (although it may not appear so on the screen), or it may not  
be recorded at all.  
❍ Copyright protected signals cannot be recorded.  
❍ Blank sections may be recorded as anomalous picture.  
❍ If the picture does not appear, reconnect the DV cable or turn the camcorder  
off and back on again.  
❍ You can connect only one device with the DV cable.  
❍ You can use the camcorder for playback and recording without reconnecting  
the DV cable.  
CAMERA  
CARD CAMERA  
CARD CAMERA  
PLAY (VCR)  
1. Connect the camcorder to the digital video device.  
See Connecting a Digital Video Device ( 88).  
AV INSERT AV DV REMOTE SET  
REC  
PAUSE  
-
WIRELESS CONTROLLER WL D79  
2. Set the camcorder to PLAY (VCR) mode and load a  
blank cassette.  
“DV IN” appears.  
3. Connected device: Load the recorded cassette.  
4. Press the REC PAUSE button on the wireless controller.  
In record pause mode and during recording, you can check the picture on the screen  
5. Connected Device: Play back the tape.  
ZERO SET  
6. Press the PAUSE a button on the wireless controller  
when the scene you wish to record appears.  
REW  
PLAY  
STOP  
SLOW  
FF  
MEMORY  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
AV INSERT AV DV REMOTE SET  
7. Press the STOP 3 button on the wireless controller to  
stop recording.  
ZERO SET  
MEMORY  
REW  
PLAY  
STOP  
SLOW  
FF  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
• Press the PAUSE a button on the wireless controller to pause  
recording.  
AV INSERT AV DV REMOTE SET  
• Press the PAUSE a button again to restart recording.  
8. Connected Device: Stop playback.  
90  
Copyright Signal  
Certain software tapes are copyright protected. If you attempt to play back such tape,  
“COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears and you will not be able  
to view the contents of the tape. If you attempt to record from such tape via the DV  
terminal, “COPYRIGHT PROTECTED DUBBING RESTRICTED” appears and you will not  
be able to record the contents of the tape.  
E
91  
Converting Analog Signals into Digital  
Signals (Analog-Digital Converter)  
E
By connecting the camcorder to a VCR or 8mm video camcorder, you can convert  
analog video/audio signals to digital signals and output the digital signals via the DV  
terminal. The DV terminal serves as output terminal only.  
❍ Headphones cannot be used during analog-digital conversion.  
❍ Unload the tape from the camcorder.  
❍ Turn off all devices before starting the connections.  
❍ Depending on the signal sent from the connected device, the conversion from  
analog to digital signals might not work properly (e.g., signals that include  
copyright protective signals or anomalous signals such as ghost signals, etc.)  
We recommend powering the camcorder from a household power source.  
Connecting the Devices  
This illustration shows how to connect using a S-video cable. You can also connect the  
yellow plug of the stereo video cable to the VIDEO terminal. Refer also to the  
instruction manual of the connected device.  
OUTPUT  
S
Signal flow  
S(S1)-VIDEO  
S-150 S-video Cable (optional)  
VIDEO  
L
AV  
Signal flow  
AUDIO  
R
STV-250N Stereo Video  
Cable (supplied)  
DV  
Signal flow  
Commercially available DV cable  
92  
Turning On the Analog-Digital Converter  
CAMERA  
CARD CAMERA  
CARD CAMERA  
PLAY (VCR)  
E
Press the AV \ DV button on the wireless controller.  
OR  
VCR SET UP  
AV DV OUT••OFF  
(
44)  
Open the menu and select [VCR SET UP]. Select [AV \ DV OUT], set it to  
[ON] and close the menu.  
❍ For normal use, set [AV \ DV OUT] to [OFF] (so that “AV \ DV” does not  
appear on the screen). If it is set to [ON], digital signals cannot be input via the  
camcorder’s DV terminal.  
❍ Depending on the software and the specifications of your computer, you may  
not be able to transfer converted signals via the DV terminal.  
93  
Replacing Existing Scenes (AV Insert)  
You can insert and replace images/audio on the tape of the camcorder with  
images/audio from other video devices connected via AV terminal or DV terminal.  
E
Scene to be inserted  
Playback tape  
Insert start  
Insert end  
Tape in the  
camcorder  
before inserting  
Tape in the  
camcorder after  
inserting  
Inserted scene  
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change  
the setting ( 39).  
❍ You cannot insert from a TV program when the synchronized signals are  
distorted.  
Camcorder:  
❍ Use only tapes recorded in SP mode.  
❍ AV insert will stop if the camcorder detects a blank section or a section not  
recorded in SP mode on the tape.  
Connected device:  
❍ Use only tapes without blank sections.  
❍ AV insert may not work correctly if the tape has a blank section or changes in  
the recording mode.  
❍ AV insert cannot be performed when the quality of the recording is poor, or  
during special playback such as fast forward, rewind, playback pause, slow  
playback etc.  
94  
Example: AV Insert from a VCR  
CAMERA  
CARD CAMERA  
CARD CAMERA  
PLAY (VCR)  
E
1. Connect the camcorder to the VCR.  
See Playing Back on a TV Screen ( 41).  
2. VCR: Load a recorded cassette. Locate the scene you wish to insert and  
pause playback shortly before the scene.  
3. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.  
Make sure the tape-protect switch is set to allow recording.  
4. Locate the scene you wish to replace and pause playback shortly before  
the scene.  
You can use the playback buttons on the camcorder or the special playback buttons on  
the wireless controller.  
12bit  
STOP  
5. Press the AV INSERT button on the wireless  
controller.  
AUDIO OUT  
AUDIO DUB. PAUSE  
SLOW  
2
AV INSERT AV DV REMOTE SET  
REC  
“AV INSERT” and “2a” appear.  
PAUSE  
6. VCR: Play back the tape.  
7. Press the PAUSE a button on the wireless controller  
when the scene you wish to insert appears.  
ZERO SET  
MEMORY  
REW  
PLAY  
STOP  
SLOW  
FF  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
AV INSERT AV DV REMOTE SET  
8. Press the STOP 3 button on the wireless controller  
to stop inserting.  
ZERO SET  
MEMORY  
REW  
PLAY  
STOP  
SLOW  
FF  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
Press the PAUSE a button on the wireless controller to pause  
AV INSERT AV DV REMOTE SET  
inserting.  
9. VCR: Stop playback.  
Set the zero set memory at the end of the scene you wish to replace. The  
camcorder will automatically stop AV insert at that point.  
95  
Audio Dubbing  
You can add sound from audio devices (AUDIO IN) or with the built-in or an external  
microphone (MIC. IN).  
E
❍ Use only tapes recorded in SP mode 12-bit audio sound with this camcorder.  
Audio dubbing will stop if the tape has a blank section or a section recorded in  
LP mode, 16-bit or 12-bit 4-channel sound. In above case, create a copy in SP  
mode 12-bit audio sound using the analog line-in function.  
❍ Do not connect/disconnect any cable to/from the camcorder while dubbing.  
❍ You cannot use the DV terminal for audio dubbing.  
❍ If you add sound to a tape not recorded with this camcorder, sound quality  
may decrease.  
❍ Sound quality may decrease when you add sound to the same scene for more  
than 3 times.  
Connecting an Audio Device  
AV  
Signal flow  
L
STV-250N Stereo Video Cable  
(supplied)  
R
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change  
the setting (  
39).  
❍ You can monitor the picture on the LCD screen or a TV connected via the  
S-video terminal, and check the sound with the built-in speaker.  
96  
Using a Microphone  
E
MIC  
❍ When using the built-in microphone: do not connect any cables to the  
microphone terminal or the accessory shoe.  
❍ When using an external microphone: Connect it to the microphone terminal.  
ZR70 MC  
❍
When using the DM-50 Microphone: Do not connect any cables to  
the microphone terminal.  
❍ When you connect a TV via the S-video terminal, you can check the picture on  
the TV screen and the sound with headphones connected to the camcorder.  
When you connect a TV via the AV terminal, you can check the picture on the  
TV screen but you cannot check the sound with headphones.  
Dubbing  
CAMERA  
CARD CAMERA  
CARD CAMERA  
PLAY (VCR)  
AUDIO SET UP  
AUDIO DUB.••AUDIO IN  
(
44)  
1. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.  
2. Open the menu and select [AUDIO SET UP]. Select  
[AUDIO DUB.], set it to [AUDIO IN] or [MIC. IN] and  
close the menu.  
3. Locate the scene you wish audio dubbing to start.  
4. Press the PAUSE a button on the wireless controller.  
5. Press the AUDIO DUB. button on the wireless  
controller.  
12bit  
STOP  
SLOW  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
AV INSERT AV DV REMOTE SET  
• “AUDIO DUB.” and “  
” appear.  
REC  
PAUSE  
ZR70 MC  
•
If the optional DM-50 microphone is attached,  
(Connection) appears.  
6. Press the PAUSE a button on the wireless controller  
to begin dubbing.  
ZERO SET  
MEMORY  
REW  
PLAY  
STOP  
SLOW  
FF  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
• Audio device: Begin playback.  
AV INSERT AV DV REMOTE SET  
• Microphone: Direct your voice to the microphone.  
97  
7. Press the STOP 3 button on the wireless controller  
to stop dubbing.  
ZERO SET  
MEMORY  
REW  
PLAY  
STOP  
SLOW  
FF  
12bit  
AUDIO OUT  
AUDIO DUB. PAUSE  
2
Audio device: Stop playback.  
AV INSERT AV DV REMOTE SET  
E
Set the zero set memory at the end of the scene you wish to dub audio. The  
camcorder will automatically stop audio dubbing at that point.  
Playing Back the Added Sound  
You can select to play back Stereo 1 (original sound), Stereo 2 (added sound), or adjust  
the balance of both sounds.  
12bit AUDIO  
OUT button  
MENU button  
Selector dial  
CAMERA  
CARD CAMERA  
CARD CAMERA  
PLAY (VCR)  
AUDIO SET UP  
12bit AUDIO•STEREO1  
(
44)  
1. Open the menu and select [AUDIO SET UP]. Select [12bit AUDIO OUT],  
select a setting and close the menu.  
• STEREO 1: Plays back the original sound.  
• STEREO 2: Plays back the added sound.  
• MIX/FIXED: Plays back stereo 1 and stereo 2 in the same level.  
• MIX/VARI.: Plays back stereo 1 and stereo 2. The mix balance can be adjusted.  
2. If you have selected [MIX/VARI.], adjust the mix level: Open the menu  
and select [AUDIO SET UP]. Select [MIX BALANCE], adjust the balance  
with the selector dial and close the menu.  
Turn the selector dial down to increase the volume of Stereo 1 and up to increase the  
volume of Stereo 2.  
❍ The camcorder resets to [STEREO 1] when you turn the camcorder off.  
However, the mix balance is memorized by the camcorder.  
❍ You can also press the 12bit AUDIO OUT button on the wireless controller to  
select the audio output. However, the mix balance can only be adjusted in the  
menu.  
98  
Connecting to a Computer Using a DV (IEEE1394) Cable  
You can transfer recordings to a computer equipped with a DV (IEEE1394) terminal or  
IEEE1394 capture board (optional software required).  
E
DV  
IEEE1394 (DV)  
terminal  
DV IN/OUT  
terminal  
Commercially available DV cable  
❍ Do not disconnect the DV cable, or turn off the camcorder or computer while  
data is being transferred to the computer.  
❍ Operation may not work correctly depending on the software and the  
specifications/settings of your computer.  
❍ We recommend powering the camcorder from a household power source  
while it is connected to the computer.  
❍ Refer also to the instruction manual of the computer.  
❍ Optional software required. Refer also to the instruction manual of the  
software.  
ZR70 MC ZR65 MC  
❍
For transferring recordings from a memory card to the  
computer using a USB cable, see p. 129.  
DV NETWORK SOLUTION DISK (Windows XP Users)  
Windows XP users can use the software on the supplied DV NETWORK SOLUTION  
DISK to perform videoconference and file transfer over the Internet, or upload files  
from the computer to the memory card and use the camcorder as card reader/writer.  
The available functions depend upon the camcorder model and the networking  
environment. For details, refer to the DV NETWORK SOLUTION DISK Software  
Instruction Manual.  
ZR70 MC ZR65 MC  
❍ Do not disconnect the DV cable, remove the memory card or turn off the  
camcorder or computer while data is being transferred to the computer (while  
the camcorder’s card access indicator is flashing). Doing so may damage the  
memory card’s data.  
❍ The image files on your memory card and the image files saved on the hard  
disk drive of your computer are your valuable, original data files. If you wish to  
use image files on your computer, be sure to make copies of them first,  
retaining the original.  
99  
Inserting and Removing the Memory Card  
The chapter Using a Memory Card (  
100-133) refers to functions of the ZR70 MC  
SD Memory Cards or a  
Terminals  
E
and ZR65 MC only.  
You can use  
commercially available MultiMediaCards with  
this camcorder. The SD Memory Card has a  
protect switch for prevent accidental erasure.  
❍ This camcorder is compatible with SD Memory Cards or MultiMediaCards only.  
Do not use any other types of memory cards.  
❍ Turn off the camcorder before inserting or removing the memory card.  
Otherwise it may result in data damage.  
❍ Do not touch the memory card terminals.  
❍ If you use memory cards other than the supplied one, make sure to format  
them with the camcorder (  
❍ For instructions on how to connect the camcorder to the computer, see  
Connecting to a Computer using a USB Cable ( 129).  
128).  
Inserting the Card  
1. Turn off the camcorder.  
2. Open the cover.  
3. Insert the memory card all the way  
into the memory card slot.  
4. Close the cover.  
Do not close the cover forcefully without  
having the card correctly inserted.  
Removing the Card  
Do not forcefully remove the memory card without first pushing it in.  
1. Turn off the camcorder.  
Make sure that the card access indicator is not  
flashing.  
2. Open the cover.  
3. Push the memory card to release it.  
Remove the memory card.  
Card access  
indicator  
4. Close the cover.  
100  
Selecting the Image Quality/Size  
Changing the Still Image Quality  
You can choose between Superfine, Fine and Normal.  
E
CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
CARD CAMERA  
CARD SET UP  
SI QUALITY••FINE  
(
44)  
Open the menu and select [CARD SET UP]. Select [SI QUALITY], set it to  
[SUPER FINE] or [NORMAL] and close the menu.  
Changing the Still Image Size  
You can choose between 1024 × 768 pixels and 640 × 480 pixels.  
CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
CARD CAMERA  
CARD SET UP  
SI SIZE•••••1024×768  
(
44)  
Open the menu and select [CARD SET UP]. Select [SI SIZE], set it to [640 ×  
480] and close the menu.  
❍ Still images recorded in 1024 × 768 pixels may not be displayed correctly in a  
camcorder not supporting this size.  
❍ Still images are compressed and recorded in the JPEG (Joint Photographic  
Experts Group) format.  
❍ Depending on subject and recording condition, changing the image quality  
may not show a significant difference.  
❍ Estimated Capacity of a 8 MB Memory Card and File Size per Image:  
640 × 480  
1024 × 768  
Image Size  
Image Quality  
File Size  
File Size  
No. of Images  
No. of Images  
per Image  
440 KB  
300 KB  
160 KB  
per Image  
175 KB  
120 KB  
65 KB  
Superfine  
Fine  
14 images  
20 images  
39 images  
35 images  
52 images  
86 images  
Normal  
These figures are approximate. They vary according to the recording condition  
and the subject. Sample images already recorded on the supplied SD Memory  
Card are to be included in the total number.  
❍ Remaining Image Capacity:  
flashing in red: No card  
in green: 6 or more images  
in yellow: 1 to 5 images  
in red: No more images  
101  
❍ The indication may not decrease even though a recording has been made, or  
may decrease by 2 images at once.  
❍ All indicators are displayed in green when a memory card is played back.  
ZR70 MC  
❍
The remaining image capacity indicates the number of still images,  
even when movies are recorded.  
E
ZR70 MC  
Changing the Movie Size  
You can choose between 320 × 240 pixels and 160 × 120 pixels.  
CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
CARD CAMERA  
CARD SET UP  
MOVIE SIZE••320×240  
(
44)  
Open the menu and select [CARD SET UP]. Select [MOVIE SIZE], set it to  
[160 × 120] and close the menu.  
❍ Movies are recorded in the Motion JPEG format.  
❍ Maximum continuous recording time:  
Max. Continuous  
Recording Time  
Image Size  
Total File Size  
File Size per Second  
320 × 240  
160 × 120  
10 sec.  
30 sec.  
2.7 MB  
2.7 MB  
270 KB/sec.  
90 KB/sec.  
File Numbers  
Images are automatically assigned file numbers from 0101 to 9900 and stored in  
folders containing up to 100 images. Folders are assigned numbers from 101 to 998.  
(The sample images on the supplied memory card are saved in the [100canon] folder.)  
You can choose to use consecutive file numbers (CONTINUOUS) or to reset the file  
number each time a different memory card is inserted (RESET). We recommend setting  
the file numbers to CONTINUOUS.  
CONTINUOUS  
The camcorder memorizes the file number of the last image and assigns the  
consecutive file number to the next image, even when a new memory card is inserted.  
(If a higher file number already exists on the memory card, the consecutive number  
will be assigned.) There will be no duplication of file numbers. This is useful for  
organizing images on a computer.  
RESET  
The file number will be reset each time a new memory card is inserted, starting with  
101-0101. If the memory card already contains image files, the consecutive file number  
will be assigned.  
102  
When you record 3 images on the supplied memory card.  
101-0101  
101  
E
101-0102  
CONTINUOUS  
RESET  
101-0103  
When you replace the memory  
card and record an image.  
101-0104  
101-0101  
101  
101  
CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
CARD CAMERA  
CARD SET UP  
FILE NOS.•••CONTINUOUS  
(
44)  
To change the setting, open the menu and select [CARD SET UP]. Select  
[FILE NOS.], set it to [RESET] and close the menu.  
103  
Recording Still Images on a Memory Card  
You can record still images with the  
Card access  
indicator  
PHOTO button  
E
camcorder, from a tape in the camcorder  
105), or from devices connected via the  
DV terminal or AV terminal ( 106).  
(
❍ Do not turn off the camcorder, disconnect the power source or remove the  
memory card while the card access display (<<< or >>>) in the upper right  
corner of the screen or the card access indicator is flashing. Doing so could  
result in data damage.  
❍ When you are using a SD Memory Card, make sure that the protect switch is  
set to allow recording.  
Make sure to insert a memory card with enough remaining capacity.  
Recording with the Camcorder  
CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
CARD CAMERA  
1. Set the camcorder to CARD CAMERA mode.  
The remaining image capacity and other information appear.  
2. Press the PHOTO button halfway.  
• F flashes in white and turns green when focus is adjusted.  
• Exposure is locked.  
P
H
O
T
O
• When you press the PHOTO button on the wireless controller,  
recording starts immediately.  
3. Press the PHOTO button fully.  
• You hear a shutter sound, and the screen appears as if a  
shutter has been released.  
P
H
O
T
O
• The card access indicator flashes.  
• The still image shown on the screen will be recorded on the memory card.  
To use the self-timer (  
70), press the  
(self-timer) button before step 2 and  
press the PHOTO button fully.  
104  
Recording from a Tape in the Camcorder  
You can record images from a tape in the camcorder as still images on a memory card.  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
E
1. Set the camcorder to PLAY (VCR) mode.  
2. Play back the tape.  
3. Press the PHOTO button halfway when the scene you wish to record  
appears.  
• The camcorder pauses playback. The remaining image capacity and other information  
appear.  
• When you press the PHOTO button on the wireless controller, recording starts  
immediately.  
4. Press the PHOTO button fully.  
• The card access indicator flashes.  
• The still image shown on the screen will be recorded on the memory card.  
• You can also record a still image by pressing the PHOTO button fully when the tape is  
in playback pause mode.  
❍ A still image recorded from an image in 16:9 format will be vertically  
compressed.  
❍ The data code of the still image will reflect the date and time it has been  
recorded on the memory card.  
❍ There will be no shutter sound in PLAY (VCR) mode.  
❍ The image size of a still image recorded from a tape in the camcorder will be  
640 x 480.  
105  
Recording from Other Video Devices  
You can record images from devices connected via the S-video terminal or AV terminal  
(analog line-in function), or via the DV terminal as still images on a memory card.  
E
When recording via the AV terminal, make sure that “AV \ DV” is displayed on  
the screen. When recording via the DV terminal, make sure that “AV \ DV” is  
not displayed. Change the setting as necessary (  
93).  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
1. Connect the camcorder to the video device.  
• S-video/AV terminal: See Playing Back on a TV Screen (  
• DV terminal: See Connecting a Digital Video Device (  
2. Set the camcorder to PLAY (VCR) mode.  
41).  
88).  
If a cassette is loaded, make sure the tape is stopped.  
3. Connected device: Load a recorded cassette and play back the tape.  
4. Press the PHOTO button halfway when the scene you wish to record  
appears.  
• The still image, remaining image capacity and other information appear.  
• When you press the PHOTO button on the wireless controller, recording starts  
immediately.  
5. Press the PHOTO button fully.  
• The card access indicator flashes.  
• The still image shown on the screen will be recorded on the memory card.  
❍ A still image recorded from an image in 16:9 format will be vertically  
compressed.  
❍ The data code of the still image will reflect the date and time it has been  
recorded on the memory card.  
❍ There will be no shutter sound in PLAY (VCR) mode.  
❍ The image size of a still image recorded from other video devices will be  
640 × 480.  
106  
Recording Panoramic Images (Stitch Assist Mode)  
You can shoot a series of overlapping images and merge them into one large  
panoramic scene using the supplied software (PhotoStitch) on a computer.  
E
When Recording in Stitch Assist Mode:  
PhotoStitch detects the overlapping portion of adjoining images and merges them. Try  
to include a distinctive item (landmark, etc.) in the overlapping portion.  
CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
CARD CAMERA  
1. Set the camcorder to CARD CAMERA mode.  
2. Press the button.  
MIX/  
SLIDE  
SHOW  
3. Select the direction with the CARD +/– button.  
CARD + button: clockwise. CARD – button: anticlockwise.  
4. Select the program AE mode and zoom on the subject.  
Adjust focus and AE shift manually as necessary. Once the sequence has started, you  
cannot change the program AE mode, AE shift, zoom or focus.  
5. Press the PHOTO button to record the first image.  
Direction and number of recorded images appear.  
P
H
O
T
O
6. Record the second image so that it overlaps a portion of the first image.  
• Minor discrepancies in the overlapped area can be corrected with the software.  
• You can retake an image by pressing the CARD – button to return to the previous  
image.  
• A maximum of 26 images can be recorded.  
7. Press the  
button after the last image.  
For details on how to merge these images, refer to the DIGITAL  
VIDEO SOLUTION DISK Software Instruction Manual.  
MIX/  
SLIDE  
SHOW  
107  
❍ Compose each image so that it overlaps 30 to 50% of the adjoining image. Try  
to keep the vertical misalignment within 10%.  
❍ Do not include moving subject in the overlapping portion.  
❍ Do not try to stitch images that include both distant and close subjects. They  
may appear warped or doubled up.  
E
108  
ZR70 MC  
Recording Motion JPEG Movies on a Memory Card  
You can record Motion JPEG movies with the camcorder, from a tape in the camcorder  
110), or from devices connected via the AV terminal (analog line-in) or the DV  
terminal ( 110).  
E
(
❍ Do not turn off the camcorder, disconnect the power source or remove the  
memory card while the card access display (<<< or >>>) in the upper right  
corner of the screen or the card access indicator is flashing. Doing so could  
result in data damage.  
❍ When you are using a SD Memory Card, make sure that the protect switch is  
set to allow recording.  
❍ Do not load/unload a cassette during recording.  
❍ Make sure to insert a memory card with enough remaining capacity.  
❍ The sound of a movie recorded on a memory card will be monaural.  
Recording with the Camcorder  
CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
CARD CAMERA  
1. Set the camcorder to CARD CAMERA mode.  
2. Press the start/stop button to begin recording.  
You can record up to 10 seconds in 320 × 240 and up to 30  
seconds in 160 × 120.  
A
R
E
M
A
C
FF  
OFF  
Y
)
LA  
P
R
C
(VVCR)  
3. Press the start/stop button to stop recording.  
The camcorder starts writing the movie on the memory card.  
To use the self-timer, press the  
press the start/stop button.  
(self-timer) button before step 2 (  
70) and  
109  
Recording from a Tape in the Camcorder  
You can record movies from a tape in the camcorder on a memory card.  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
E
1. Set the camcorder to PLAY (VCR) mode.  
2. Play back the tape.  
3. Press the start/stop button when the scene you wish to record appears.  
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.  
4. Press the start/stop to stop recording.  
❍ A movie recorded from an image in 16:9 format will be vertically compressed.  
❍ The data code of the movie will reflect the date and time it has been recorded  
on the memory card.  
Recording from Other Video Devices  
You can record movies from devices connected via the S-video terminal or AV terminal  
(analog line-in function), or via the DV terminal on a memory card.  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
1. Connect the camcorder to the video device.  
• S-video/AV terminal: See Playing Back on a TV Screen (  
• DV terminal: See Connecting a Digital Video Device (  
2. Set the camcorder to PLAY (VCR) mode.  
41).  
88).  
If a cassette is loaded, make sure the tape is stopped.  
3. Connected device: Load a recorded cassette and play back the tape.  
4. Press the start/stop button when the scene you wish to record appears.  
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.  
5. Press the start/stop button to stop recording.  
❍ A movie recorded from an image in 16:9 format will be vertically compressed.  
❍ The data code of the movie will reflect the date and time it has been recorded  
on the memory card.  
110  
Playing Back a Memory Card  
You can play back memory card images on the LCD screen, viewfinder screen, or on a  
E
connected TV screen (see Playing Back on a TV Screen (  
41) ).  
You can display a single image (single image display  
111), 6 at one time (index  
screen  
to quickly locate an image without displaying them one by one (  
❍ Images not recorded with this camcorder, uploaded from a computer (except  
the sample images 132), edited on a computer and images whose file  
112), or one after another (slide show  
112). Use the Card Jump function  
113).  
names have been changed may not be played back correctly.  
❍ Still images not recorded with this camcorder may not be printed correctly on a  
Bubble Jet Printer with direct print function.  
❍ Do not turn off the camcorder, disconnect the power source or remove the  
memory card while the card access display (<<<) in the upper right corner of  
the screen or the card access indicator is flashing. Doing so could result in data  
damage.  
❍ Make sure to insert a memory card that contains images.  
❍ Only date and time will be displayed when pressing the DATA CODE button.  
❍ You can enlarge still images by 2 times during playback (  
82).  
Single Image Display  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
1. Set the camcorder to CARD PLAY (VCR) mode.  
• The last recorded image appears.  
ZR70 MC  
•
Movies are displayed with the first scene as a still image indicated by  
“e/a”.  
2. Press the CARD+/– button to move between images.  
Press the CARD + button to display the next image and the  
CARD – button to display the previous image.  
ZR70 MC  
3.  
To play back a movie, press the e/a button.  
FOCUS  
The last scene appears as a still image when playback is  
complete.  
111  
Index Screen  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
E
1. In single image display, press the  
button.  
(index screen)  
AE SHIFT  
• Up to 6 images appear.  
ZR70 MC  
•
Movies are displayed with the first scene as a still  
image indicated by “ ”.  
2. Press the CARD +/– button to change the image  
selection.  
3. Move the  
mark to the image you wish to view.  
• Turn the selector dial up to move to the next image and down  
to move to the previous image.  
• Turning the selector dial up on the last image displays the next  
index screen. Turning the selector dial down on the first image  
displays the previous index screen.  
4. Press the  
(index screen) button.  
The index screen is canceled and the selected image appears in  
single image display.  
AE SHIFT  
Slide Show  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
1. In single image display, press the SLIDE SHOW  
button.  
MIX/  
Images are played back one after another.  
SLIDE  
SHOW  
2. Press the SLIDE SHOW button to stop the slide show.  
112  
Card Jump Function  
You can locate still images/movies without displaying them one by one. The number in  
the upper right of the screen indicates the image number of the current image by the  
total number of images.  
E
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
In single image display, press and hold the CARD + or  
CARD – button.  
• Press the CARD + button to jump forward and the CARD – button  
to jump backward.  
• When you release the button, the still image/movie of the  
displayed image number appears.  
113  
Protecting Images  
You can protect important images from accidental erasure during single image display  
or index screen display.  
E
If a memory card is formatted, all images, even protected ones, will be erased  
permanently.  
❍ The sample images recorded on the supplied SD Memory Card are already  
protected.  
ZR70 MC  
❍
Movies can only be protected when the first or last scene is displayed  
as a still image. They cannot be protected during playback pause.  
❍ Make sure to insert a memory card that contains images.  
Protecting during Single Image Display  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
1. Select the image you wish to protect.  
2. Press the selector dial to open the FILE OPERATION menu.  
3. Select [PROTECT ].  
• “ ” appears and now the image cannot be erased.  
• To cancel the protection, press the selector dial.  
4. Select [b RETURN] to close the menu.  
Protecting during Index Screen Display  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CARD OPERATIONS  
PROTECT  
(
44)  
1. In single image display, press the  
(index screen) button.  
Up to 6 images appear.  
2. Open the menu and select [CARD OPERATIONS].  
3. Select [\ PROTECT ].  
4. Select the image you wish to protect and press the selector dial.  
• “ ” appears on the image.  
• Repeat this step to protect more images.  
• To cancel the protection, press the selector dial.  
5. Press the MENU button.  
To cancel the protection, press the selector dial in step 4. “  
the image can now be erased.  
” disappears and  
114  
Erasing Images  
You can erase images singly or all at once.  
E
Be careful when erasing images. Erased images cannot be recovered.  
❍ Protected images cannot be erased.  
ZR70 MC  
❍
Movies can only be erased when the first or last scene is displayed as  
a still image. They cannot be erased in playback pause mode.  
❍ Make sure to insert a memory card that contains images.  
Erasing a Single Image  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
1. Select the image you wish to erase.  
2. Press the selector dial to open the FILE OPERATION menu.  
3. Select [IMAGE ERASE].  
• “ERASE THIS IMAGE?”, [NO] and [YES] appears.  
• If an image is protected, [YES] appears in purple.  
4. Select [YES].  
The image is erased and the previous image appears.  
5. Select [b RETURN] to close the menu.  
Erasing a Single Image/All Images  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CARD OPERATIONS  
IMAGE ERASE  
(
44)  
1. Open the menu and select [CARD OPERATIONS].  
2. Select [IMAGE ERASE].  
3. Select [SINGLE] or [ALL].  
• When erasing a single image: “ERASE THIS IMAGE?” [NO] and  
[YES] appears. If an image is protected, [YES] appears in purple.  
• When erasing all images: “ERASE ALL IMAGES? [EXCEPT FOR  
and [YES] appears.  
IMAGES]”, [NO]  
4. Select [YES] and close the menu.  
• When erasing a single image: The image is erased and the previous image appears. To  
erase another image, select the image with the CARD +/– button and select [YES].  
• When erasing all images: All images with exception of the protected images are erased.  
115  
Selecting Still Images for Printing (Print Order)  
You can select still images for printing and set the number of copies. These print order  
settings are compatible with the Digital Print Order Format (DPOF) standards.  
E
❍ Make sure to insert a memory card that contains images.  
❍ A maximum of 200 still images can be selected.  
ZR70 MC  
❍
Movies cannot be printed.  
Selecting in Single Image Display  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
1. Select the still image you wish to print.  
2. Press the selector dial to open the FILE OPERATION menu.  
3. Select [ PRINT ORDER].  
4. Select the number of copies.  
• “ ” appears on the image.  
• To cancel the print order, set the number of copies to 0.  
5. Select [b RETURN] to close the menu.  
Selecting in Index Screen Display  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CARD OPERATIONS  
PRINT ORDER  
(
44)  
1. In single image display, press the  
(index screen) button.  
Up to 6 images appear.  
2. Open the menu and select [CARD OPERATIONS].  
3. Select [\ PRINT ORDER].  
4. Select the still image you wish to print and press the selector dial.  
5. Set the number of copies with the selector dial and close the menu.  
• “ ” appears on the image.  
• To cancel the print order, set the number of copies to 0.  
• Repeat steps 4 and 5 to continue the print order setting.  
116  
Erasing All Print Orders  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
E
CARD OPERATIONS  
PRINT ORDERS ALL ERASE  
(
44)  
1. In single image display, open the menu and select [CARD OPERATIONS].  
2. Select [  
“ERASE ALL  
PRINT ORDERS ALL ERASE].  
PRINT ORDERS?”, [NO] and [YES] appears.  
3. Select [YES].  
All “ ” disappear.  
4. Select [b RETURN] to close the menu.  
117  
Printing with the Direct Print Function  
You can print still images by connecting the camcorder to a Canon Bubble Jet Printer  
with Direct Print function. The Direct Print function can also be used with the print  
E
order settings (  
116).  
❍ Observe the following precautions during printing, otherwise printing may not  
be performed correctly.  
-
-
-
-
Do not turn off the camcorder or the printer.  
Do not change the position of the TAPE/CARD switch.  
Do not detach the cable.  
Do not remove the memory card.  
❍ Canon Bubble Jet Printers with Direct Print function (as of January 2003):  
S830D, S820D, S530D.  
❍ We recommend powering the camcorder from a household power source.  
❍ Refer also to the instruction manual of the respective printer.  
Connecting the Printer to the Camcorder  
ER  
W
POOWER  
TAPE  
CARD  
RA  
ME  
CAMERA  
FF  
OFF  
AY  
PL  
)
CR  
(VCR)  
Canon Bubble Jet Printer with direct  
print function  
1. Turn off the camcorder and insert a memory card that contains images.  
2. Connect a power source to the printer and turn on the printer.  
3. Set the camcorder to CARD PLAY (VCR) mode.  
Wait until the card access indicator stops flashing.  
4. Connect the camcorder to the printer using the cable.  
Print  
SET  
appears when the printer is properly connected to the camcorder. (Does not  
appear with movies, or still images that cannot be played back with the camcorder.)  
118  
Printing  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
E
1. In single image display, select the still image you  
wish to print and press the selector dial.  
The print setting menu appears.  
2. Set the number of copies and the print style.  
• Selecting the Number of Copies.  
• Setting the Print Style.  
3. Select [Print] and press the selector dial.  
Printing starts. The print setting menu disappears when printing  
is complete.  
If an error message appears, see Printing Errors (  
Messages ( 140).  
121) and Direct Print Related  
Selecting the Number of Copies  
A maximum of 9 copies can be selected for one still image.  
1. In the print setting menu, turn the selector dial so  
that appears next to [Copies] and press the  
selector dial.  
2. Turn the selector dial to select the number of copies and press the  
selector dial.  
Setting the Print Style  
Paper Size  
Card #1*, Card #2*, Card #3*, LTR, A4  
For details on paper type, refer to the Bubble Jet Printer User  
Guide.  
Borders Borderless Prints right to the edges of the page  
Bordered Prints with a border  
* Recommended paper size  
119  
Selecting the paper size:  
1. In the print setting menu, turn the selector dial to  
select [Style] and press the selector dial.  
E
2. Make sure that is selected and press the selector  
dial.  
3. Turn the selector dial to select the paper size and press the selector dial.  
4. Press the MENU button.  
You return to the print setting menu.  
Selecting the Borders:  
1. In the print setting menu, turn the selector dial to  
select [Style] and press the selector dial.  
2. Select  
and press the selector dial.  
3. Select a setting option and press the selector dial.  
4. Press the MENU button.  
You return to the print setting menu.  
❍ Bordered: The image area remains relatively unchanged from the recorded  
image when it is printed.  
❍ Borderless: The center portion of the recorded image is printed at an enlarged  
size. The image’s top, bottom and sides may be cropped slightly.  
120  
Printing with Print Order Settings  
You can print still images you have selected with the Print Order function. If you wish  
to print more than 1 copy, set the number of copies in the print order (  
116).  
E
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
PRINT  
(
44)  
1. Connect the printer to the camcorder (  
2. Press the MENU button.  
118).  
3. Select [\  
PRINT].  
• The print setting menu appears.  
• “Set print order” appears, when you connect a printer with direct print function and  
select \ PRINT without having set the print order.  
• The total number of prints set in the print order is displayed on the upper left of the  
screen.  
4. Set the print style.  
Setting the Print Style (  
119).  
5. In the print setting menu, select [OK] and press the selector dial.  
Printing starts. The print setting menu disappears when printing is complete.  
❍ Cancel Printing  
Press the selector dial while “Now Printing” is displayed. A confirmation dialog  
appears. Select [OK] and press the selector dial. Printing stops even if it is  
incomplete and the paper is fed through.  
❍ Restarting Printing (with  
print order only)  
Open the CARD PLAY (VCR) menu and select [\  
PRINT]. Select [Restart] in  
the print setting menu and press the selector dial. The remaining images will  
be printed.  
Printing cannot be restarted in the following cases:  
-
-
When you change the print order settings.  
When you delete a still image with print order settings.  
❍ Printing Errors  
If an error occurs during the printing process, an error message appears  
(
140). With most errors, printing resumes automatically after you correct  
the error. If the error persists, press the selector dial to cancel printing.  
❍ Follow below procedure when disconnecting the interface cable:  
1. Disconnect the cable from the camcorder and printer.  
2. Turn off the camcorder.  
121  
Combining Images (Card Mix)  
You can produce effects not possible with just a tape with the Card Mix function.  
Choose one of the sample images provided on the supplied SD Memory Card (such as  
picture frames, backgrounds and animations) and combine it with the live video  
recording.  
E
❍ Card Mix cannot be used in the Night and Super Night (ZR70 MC) mode.  
ZR70 MC  
❍
Movies recorded on a memory card cannot be combined with  
camcorder recordings.  
❍ Make sure to load a cassette and to insert a memory card that contains card  
mix images.  
❍ Additional sample images are provided on the supplied DIGITAL VIDEO  
SOLUTION DISK. For instructions on how to upload them to the memory card,  
refer to Adding Still Images from Your Computer to the Memory Card in the  
DIGITAL VIDEO SOLUTION DISK Software Instruction Manual.  
❍ Reselect the card mix image when you have turned off the camcorder or  
changed the position of the program selector.  
Card Mix Effects  
You can select from the following 4 types of Card Mix effects:  
Card Chroma Key (CARD CHROMA)  
Combines frames with your recordings. The live video recording will appear in place of  
the blue area of the card mix image. If you create your own frame, make sure that the  
area the live recording should appear is blue.  
Mix level adjustment: blue area of the still image.  
Live video recording  
Card mix image  
122  
Card Luminance Key (CARD LUMI.)  
Combines illustrations or title with your recordings. The live video recording will  
appear in place of the light area of the card mix image. You can create your own title  
or illustration by drawing on a white paper and recording it to the memory card.  
Mix level adjustment: light area of the still image.  
E
Live video recording  
Card mix image  
Camera Chroma Key (CAM. CHROMA)  
Combines backgrounds with your recordings. Record your subject in front of a blue  
curtain, and the subject not blue will be superimposed on the card mix image.  
Mix level adjustment: blue area of the live video recording.  
Live video recording  
Card mix image  
Card Animation (C. ANIMATION)  
Combines animations with your recordings. You can choose from 3 types of card  
animation effects.  
Corner: Animation appears on the upper left and the lower right corner of the screen.  
Straight: Animation appears on the top and bottom of the screen and moves to the  
right and left.  
Random: Animation moves randomly in the display.  
Mix level adjustment: blue area of the card animation image.  
Live video recording  
Card mix image  
123  
Selecting the Card Mix Effect  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CAMERA  
E
CARD MIX  
MIX TYPE•••CARD CHROMA  
–
+
MIX LEVEL••  
(
44)  
1. Set the program selector to Q.  
2. Open the menu and select [\ CARD MIX].  
The card mix menu appears.  
3. Select the image you wish to combine with the  
CARD +/– button.  
4. Select [MIX TYPE].  
[CARD CHROMA], [CARD LUMI.], [CAM. CHROMA] and [C. ANIMATION] appears.  
5. Select the mix type matching the image you have selected (  
132).  
• The screen shows the combined image.  
• When you have selected [C. ANIMATION], select [ANIMAT. TYPE] and select between  
[CORNER], [STRAIGHT] and [RANDOM].  
6. To adjust the mix level, select [MIX LEVEL] and adjust it with the  
selector dial.  
7. Close the menu.  
MENU  
“CARD MIX” flashes.  
Activating the Card Mix Effect  
1. Press the CARD MIX button.  
• “CARD MIX” stops flashing.  
MIX/  
• The combined image appears.  
SLIDE  
SHOW  
• You can activate and deactivate the card mix effect by pressing  
the CARD MIX button.  
124  
Recording with the Card Mix Effect  
Movie:  
1. Press the start/stop button to begin recording.  
The combined image is recorded on the tape.  
E
A
R
E
M
A
C
FF  
OFF  
Y
LA  
P
)
R
C
(VVCR)  
2. Press the start/stop button to end recording.  
Still Image:  
1. Press the PHOTO button halfway.  
F flashes in white and turns green when focus is adjusted.  
P
H
O
T
O
2. Press the PHOTO button fully.  
• The camcorder records the still image on the tape for approx. 6  
seconds. During this time, the camcorder displays the still  
image and keeps recording the sound.  
P
H
O
T
O
• The camcorder returns to record pause mode.  
125  
Copying Still Images  
You can copy still images from tape to memory card, or from memory card to tape.  
E
❍ All still images from the selected still image onward will be copied.  
❍ The image size of a still image copied from tape to memory card will be 640 ×  
480.  
❍ The data code of the still image reflects the date and time it has been copied.  
Copying Still Images from Tape to Memory Card  
Insert a memory card with enough remaining capacity, and load a recorded cassette.  
CAMERA  
CARD CAMERA  
CARD PLAY (VCR)  
PLAY (VCR)  
CARD OPERATIONS  
COPY  
[
]
(
44)  
1. Locate the still image you wish to copy on the tape  
and stop the tape shortly before the still image.  
• You can also use the photo search function to easily locate the  
still image.  
• To copy all still images from the tape, rewind the tape to the beginning.  
2. Open the menu and select [CARD OPERATIONS].  
3. Select [COPY [b \  
] ].  
[CANCEL] and [EXECUTE] appears.  
4. Select [EXECUTE].  
• “NOW COPYING” appears.  
• The still image being copied is shown on the screen.  
• Copying stops when the tape reaches the end or the memory card is full (“CARD  
FULL” appears).  
5. Press the 3 (stop) button to end copying.  
AE SHIFT  
126  
Copying Still Images from Memory Card to Tape  
Load a cassette with enough free space, and insert a recorded memory card. Make  
sure that the protect tab on the cassette is set to allow recording.  
E
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
[
COPY  
]
CARD OPERATIONS  
(
44)  
1. Select the first still image you wish to copy with the  
CARD +/– buttons.  
To copy all still images from the memory card, select the first still  
image.  
2. Open the menu and select [CARD OPERATIONS].  
3. Select [COPY [  
\ b] ].  
[CANCEL] and [EXECUTE] appears.  
4. Select [EXECUTE].  
• “NOW COPYING” appears.  
• It takes about 6 seconds per still image to be copied to the tape.  
• Copying stops when all still images are copied or the tape is full.  
5. Press the 3 (stop) button to end copying.  
AE SHIFT  
127  
Formatting a Memory Card  
Format new memory cards, or when you get the message “CARD ERROR”. You can  
also format a memory card to erase all images recorded on it.  
The camcorder formats memory cards in the Design rule for Camera File system (DCF)  
standard.  
E
❍ Formatting a memory card erases all data, including protected images.  
❍ Images erased by formatting cannot be recovered.  
❍ If you use a memory card other than the supplied one, format it with the  
camcorder.  
❍ Makes sure to insert the memory card you wish to format into the camcorder.  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
CARD OPERATIONS  
FORMAT  
(
44)  
1. Open the menu and select [CARD OPERATIONS].  
2. Select [FORMAT].  
[CANCEL] and [EXECUTE] appears.  
3. Select [EXECUTE].  
[FORMAT THIS CARD?], [NO] and [YES] appears.  
4. Select [YES] and close the menu.  
• Formatting starts.  
• Selecting [NO] brings you back to step 3.  
128  
Connecting to a Computer Using a USB Cable  
You can download images from the memory card to a computer using the supplied  
USB cable. With the supplied software, you can easily download, browse and archive  
images, and arrange still images for printout.  
E
For instructions on how to connect the camcorder to the computer, and  
install and operate the software, refer to the DIGITAL VIDEO SOLUTION  
DISK Software Instruction Manual.  
• Refer also to the computer instruction manual.  
PC CONNECT  
• “PC CONNECT  
” appears to indicate that the camcorder is  
connected to the computer via USB cable.  
❍ Do not disconnect the USB cable, remove the memory card, change the  
position of the POWER switch or turn off the camcorder and computer while  
data is being transferred to the computer (while the camcorder’s card access  
indicator is flashing). Doing so may damage the memory card’s data.  
❍ Operation may not work correctly depending on the software and the  
specifications/settings of your computer.  
❍ The image file on your memory card and the image files saved on the hard disk  
drive of your computer are valuable, original data files. If you wish to use  
image files on your computer, make copies of them first, and use the copied  
file, retaining the original.  
❍ We recommend powering the camcorder from a household power source  
while it is connected to the computer.  
ZR70 MC  
❍
The light-up buttons turn off during USB connection.  
❍ For transferring recordings from to a computer using a DV cable, see p. 99.  
❍ Still images/movies recorded on a tape cannot be transferred to a computer via  
USB interface.  
129  
Creating a Start-up Image  
You can create a start-up image using a still image on the memory card or a sample  
start-up image provided on the DIGITAL VIDEO SOLUTION DISK and save it as [MY  
IMAGE].  
E
❍ Make sure to insert a memory card with enough remaining capacity.  
❍ Before you create a start-up image, you need to record a still image on the  
memory card.  
❍ Retain the original data of the still image you have set as the start-up image on  
your computer or removable disk.  
Preparations  
Record a still image on the memory card.  
OR  
Upload a still image from your computer to the memory card using the  
software in the DIGITAL VIDEO SOLUTION DISK.  
For instruction on how to upload a still image to the memory card, refer to Adding Still  
Images from Your Computer to the Memory Card in the DIGITAL VIDEO SOLUTION DISK  
Software Instruction Manual.  
Setting the Still Image as Start-up Image  
CAMERA  
PLAY (VCR)  
CARD CAMERA  
CARD PLAY (VCR)  
MY CAMERA  
CREATE START–UP IMAGE  
(
44)  
1. Open the menu.  
2. Select [MY CAMERA].  
3. Select [CREATE START-UP IMAGE].  
[SET THIS AS START-UP IMAGE?], [YES] and [NO] appears.  
4. Select a still image with the CARD +/– buttons and select [YES].  
[OVERWRITE MY IMAGE?], [YES] and [NO] appears.  
5. Select [YES].  
The still image will be saved, and the image that was saved to [MY IMAGE] is erased.  
130  
Memory Card Information  
Images recorded on a memory card with this camcorder can be transferred to a  
computer using the following products for SD Memory Cards or MultiMediaCards:  
E
PC Card Adapter: An adapter to insert a memory card into the card slot on the  
computer.  
USB Reader/Writer: Connects to the USB port of a computer for direct access to the  
memory card.  
FD Adapter:  
An adapter to insert a memory card into the floppy disk drive on  
the computer.  
Memory Cards that are confirmed to operate with this camcorder  
(as of January 2003):  
SD Memory Card: Panasonic: 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB  
SanDisk: 16 MB, 32 MB, 64 MB  
MultiMediaCard: SanDisk: 16 MB, 32 MB, 64 MB  
However, we cannot guarantee that all of these memory cards work properly.  
Memory Card Handling Precautions  
❍ Format new memory cards with the camcorder. Memory cards formatted with  
other devices such as a computer may not operate correctly.  
❍ We recommend saving backups of memory card images on your computer’s hard  
drive or other external memory device. Image data may be corrupted or lost due to  
memory card defects or exposure to static electricity. Canon Inc. makes no  
warranties for corrupted or lost data.  
❍ Do not turn off the camcorder, disconnect the power source or remove the memory  
card while the card access indicator is flashing.  
❍ Do not use memory cards in places subject to strong magnetic fields.  
❍ Do not leave memory cards in places subject to high humidity and high  
temperature.  
❍ Do not disassemble memory cards.  
❍ Do not bend, drop, or subject memory cards to shocks and do not expose them to  
water.  
❍ Moving a memory card rapidly between hot and cold temperatures may cause  
condensation to form on its external and internal surfaces. If condensation forms  
on the card, put it aside until the droplets have evaporated completely.  
❍ Do not touch or expose the terminals to dust or dirt.  
❍ Store and carry memory cards in the supplied case to protect the terminals.  
❍ Check the direction before inserting the memory card. Forcing a memory card  
backwards into the slot may damage the memory card or the camcorder.  
❍ Do not remove the label from the memory card, or affix other labels on the  
memory card. If you wish to add labels, affix them to the case.  
131  
Sample Images  
27 sample images are pre-recorded on the supplied SD Memory Card: 8 card chroma  
key images, 5 card luminance key images, 2 camera chroma key images and 12 card  
animation images.  
E
Card Chroma Key  
Card Luminance Key  
Camera Chroma Key  
Card Animation  
132  
The sample images recorded on the supplied SD Memory Card are intended only  
for the personal use with this camcorder. Do not use these sample images for  
other purposes.  
E
If you have mistakenly erased the Card Mix sample images on the supplied SD  
Memory Card, they can be downloaded from the homepage  
http://www.canondv.com.  
For details on how to add the downloaded images to the memory card, refer to  
Adding Still Images from Your Computer to the Memory Card in the DIGITAL  
VIDEO SOLUTION DISK Software Instruction Manual.  
If you cannot use the USB cable to connect the camcorder to a computer, you will  
need a PC Card Adapter to upload the images to a memory card.  
PhotoEssentials – Royalty Free Stock Photography  
The PhotoEssentials suite of royalty-free images on CD-ROM features premium quality assignment  
photography and is ideally suited for use in advertising, brochures, reports, multimedia, websites,  
books, packaging and more.  
For more information, please visit their website www.photoessentials.com  
133  
Screen Displays  
LCD Screen Displays  
You can hide the displays on the LCD screen to have a clear screen for playback.  
E
CAMERA  
CARD CAMERA  
PLAY (VCR)  
CARD PLAY (VCR)  
DISPLAY SET UP  
DISPLAYS••••ON  
(
44)  
Open the menu and select [DISPLAY SET UP]. Select [DISPLAYS], set it to  
[OFF <PLAYBK>] and close the menu.  
• The LCD screen will become completely blank (also the TV screen if connected).  
• Warning messages still appear, and the data code appears if turned on.  
• Tape operation displays appear for 2 seconds.  
ZR70 MC ZR65 MC  
•
Displays cannot be hidden on the index screen.  
TV Screen Displays  
When you connect a TV for recording/playback, you can hide the displays on the TV  
screen. For connecting instructions, see Playing Back on a TV Screen (  
41).  
CAMERA  
PLAY (VCR) CARD CAMERA  
CARD PLAY (VCR)  
Press the TV SCREEN button on the wireless controller.  
SELF T. D.EFFECT.  
MENU  
SET  
ON/OFF  
TV SCREEN  
• When the POWER switch is set to CAMERA: The displays  
disappear from the TV screen and appear when you press the  
button again.  
INDEX SLIDE SHOW  
CARD  
DATA CODE SEARCH SELECT  
• When the POWER switch is set to PLAY (VCR): The displays appear on the connected TV  
screen and disappear when you press the button again. The setting resets to the OFF  
setting when you turn the camcorder off.  
When the TV screen displays are hidden, the displays still appear on the LCD screen. If  
you turn on the data code, displays other than the data code will disappear from the LCD  
screen.  
You can also change the setting in the menu during recording:  
PLAY (VCR)  
CARD PLAY (VCR)  
CAMERA  
CARD CAMERA  
DISPLAY SET UP  
TV SCREEN•••ON  
(
44)  
Open the menu and select [DISPLAY SET UP]. Select [TV SCREEN], set it to  
[OFF] and close the menu.  
134  
Screen Displays during Basic Recording/Playback  
indicates flashing.  
E
SP PAUSE  
0:00:00  
5min  
CAMERA mode (battery pack attached):  
• Remote sensor mode and audio mode disappear after 4  
seconds.  
1
12bit  
STEREO1  
SP STOP  
0:00:00:00  
5min  
PLAY (VCR) mode:  
• Remote sensor mode and volume bar disappear after 4  
seconds.  
1
–
+
: Fast forward playback/  
rewind playback ( 38)  
: ×2 playback  
RTN  
RTN  
REC  
/
/
: Zero set memory (forward  
and reverse) ( 86)  
PAUSE  
STOP  
EJECT  
2
1
2
1
/
/
: AV insert editing ( 94)  
: Audio dubbing ( 96)  
(forward and reverse) ( 38)  
: ×1 playback  
/
/
(forward and reverse) ( 38)  
: Slow playback  
(forward and reverse) ( 38)  
: Frame advance playback/  
frame reverse playback ( 38)  
: Playback pause  
FF  
REW  
/
/
/
(forward and reverse) ( 38)  
: Date search/photo search ( 85)  
/
STEREO1  
PAUSE  
1:23:45:00  
END  
Time code ( 86)  
Remaining tape  
1
: Backup  
battery ( 19)  
Remaining battery charge ( 18)  
: Condensation  
warning ( 143)  
Remote sensor mode ( 49)  
Audio mode ( 71)  
16bit  
135  
Screen Displays during Advanced Recording/Playback  
CAMERA Mode  
*
ZR70 MC  
E
Recording reminder/  
Self-timer countdown ( 70)/  
Photo recording timer ( 55)  
Image stabilizer ( 69)  
Zoom ( 30)  
Recording mode  
AE shift ( 77)  
Program AE ( 57)  
Manual focus ( 75)  
Shutter speed ( 78)  
White balance ( 80)  
Card mix ( 122)  
(
54)  
W
T
SP  
Self-timer ( 70)  
Headphones ( 39)  
0
1sec  
AE  
MF  
1/100  
Wind screen ( 71)  
Audio mode ( 71)  
–
+
CARD MIX  
FADE–T  
WSON  
12bit  
16:9  
Digital effects ( 61)  
12:00 PM  
JAN.1,2003  
16:9 mode ( 52)  
Photo mode ( 55)  
PHOTO  
Date and time ( 83)  
AF/AE locked in  
Photo mode ( 55)  
Accessory attached to  
the Advanced Accessory  
shoe* ( 73)  
PLAY (VCR) Mode  
Photo search/  
Date search ( 85)  
MIX/VARI.  
1
12bit audio out ( 98)  
1
10  
10  
1
PHOTO SEARCH  
Photo search/  
Volume level of built-in  
speaker or headphones  
Date search ( 85)/  
AV insert ( 94)/  
Audio dubbing ( 96)  
–
+
F1.8  
(
40)  
1/1000  
12bit  
DV IN  
12:00 PM  
JAN.1,2003  
Audio mode ( 71)  
DV input ( 90)  
Data code ( 83)  
136  
ZR70 MC ZR65 MC  
CARD CAMERA Mode  
ZR70 MC  
*
Recording on a memory  
card ( 104)  
Stitch assist ( 107)  
E
Still image quality ( 101)  
Zoom ( 30)  
Remaining card capacity  
(
101)  
Program AE ( 57)  
W
T
S.FINE  
50  
1 2  
Still image size  
0
AE shift ( 77)  
Manual focus  
AE  
MF  
1/100  
1024  
320  
(
101)  
Movie size* ( 102)  
(
75)  
Self-timer ( 70)  
Shutter speed  
78)  
White balance  
80)  
12:00 PM  
JAN.1,2003  
(
CLOSE  
Stitch assist ( 107)  
(
Date and time ( 83)  
Accessory attached to  
the Advanced Accessory  
shoe* ( 73)  
AF/AE locked in  
Photo mode ( 104)  
ZR70 MC ZR65 MC  
CARD PLAY (VCR) Mode  
Print order ( 116)  
Protect mark ( 114)  
Folder number-  
File number ( 102)  
Slide show ( 112)  
SLIDE SHOW  
101–0143  
43/50  
Current still image/  
Total still images  
640 480  
Accessing  
a memory card ( 111)  
12:00 PM  
JAN.1,2003  
Data code ( 83)  
137  
List of Messages  
Message  
SET THE TIME ZONE,  
DATE AND TIME  
Explanation  
E
You have not set the time zone, date and time. This message 25  
appears each time you turn the power on until you set the  
time zone, date and time.  
CHANGE THE  
Battery pack is exhausted. Replace or charge the battery  
pack.  
16  
23  
22  
90  
143  
22  
54  
96  
94  
91  
91  
BATTERY PACK  
THE TAPE IS SET FOR  
ERASURE PREVENTION position of the protect switch.  
Cassette is protected. Replace the cassette or change the  
REMOVE THE  
CASSETTE  
Camcorder stopped operating to protect the tape. Unload  
and reload the cassette.  
CHECK THE DV INPUT DV cable is not connected, or the connected digital device is  
turned off.  
CONDENSATION HAS Condensation has been detected in the camcorder.  
BEEN DETECTED  
TAPE END  
Tape reached the end. Rewind the tape or replace the  
cassette.  
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a  
[REC MODE] tape recorded in a mode other than the SP mode.  
CHECK THE CASSETTE You attempted to perform audio dubbing on a tape  
[AUDIO MODE] recorded in 16-bit or 12-bit 4-channel sound.  
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a  
[BLANK]  
tape with a blank section.  
COPYRIGHT PROTECTED  
PLAYBACK IS RESTRICTED  
You attempted to play back a copyright protected tape.  
COPYRIGHT  
You attempted to dub a copyright protected tape. May also  
PROTECTED DUBBING appear when an anomalous signal is received during analog  
RESTRICTED  
line-in recording, or during analog-digital conversion of a  
copyright protected tape.  
138  
ZR70 MC ZR65 MC  
Memory Card Related Messages  
Message  
Explanation  
NO CARD  
Memory card not is inserted into the camcorder.  
100  
100  
E
THE TAPE IS SET FOR  
ERASURE PREVENTION card or change the position of the protect switch.  
SD Memory Card is set for erasure prevention. Replace the  
NO IMAGES  
No images are recorded on the memory card.  
111  
CARD ERROR  
A memory card error occurred. The camcorder cannot record 100  
or play back the image.  
The error may be temporary. If the message disappears after  
4 seconds and flashes red, turn the camcorder off, remove  
the card and reinsert the card. If  
can continue recording/playback.  
changes to green, you  
CARD FULL  
No remaining capacity on the memory card. Replace with  
another card or erase images.  
115  
NAMING ERROR  
File or folder number has reached the maximum value.  
102  
111  
UNIDENTIFIABLE  
IMAGE  
Image is recorded in a not compatible JPEG format or  
another format not compatible with the camcorder, or the  
image file is corrupted.  
PRINT ORDER ERROR You attempted to set more than 200 still images in the print 116  
order.  
THIS IMAGE CANNOT Some analog images cannot be recorded on the memory  
BE RECORDED card depending on the signal.  
106  
139  
ZR70 MC ZR65 MC  
Direct Print Related Messages  
Message  
No Paper  
Explanation  
Paper cassette is not correctly inserted or is out of paper.  
The paper jammed during printing.  
E
Paper Jam  
No Ink  
The ink cartridge is not inserted or is out of ink.  
Communication Error The printer is experiencing a data transmission error.  
Could not print X  
images  
You attempted to use the print order settings to print X images  
that were made with another camcorder, have a different format  
or were edited on a computer.  
Cannot Print!  
Set print order  
Printer in use  
You attempted to print an image that was made with another  
camcorder, has a different format, or was edited on a computer.  
You attempted to print an image from the Card Play menu  
[\ PRINT] without having set the print order.  
The printer is printing from a computer or a memory card inserted  
into the printer. It automatically starts printing from the  
camcorder when current prints are complete.  
Printer warming up  
Printer is warming up. The printer automatically starts printing  
when it is ready.  
No printhead  
No print head is installed in the printer.  
Printer cover open  
Media type error  
Printer cover is open. Close the printer cover securely.  
Wrong paper. Cancel printing and set the paper you chose in the  
print settings menu.  
Paper lever error  
Low ink level  
Paper lever error occurred. Adjust the paper selection lever to the  
proper position.  
The ink tank needs to be replaced soon. Prepare a new ink tank. If  
you select [Continue] in the error screen, you can restart printing.  
Waste tank full  
Waste tank is full. You can restart printing by pressing the  
RESUME/CANCEL button on the Bubble Jet Printer. Request  
replacement of the waste tank at the shop where you purchased  
the printer or the nearest Canon customer support center listed in  
the Bubble Jet Quick Start Guide.  
Printer error  
Turn off the printer and turn it back on. If the error persists,  
consult the nearest Canon customer support center listed in the  
Bubble Jet Quick Start Guide.  
140  
Maintenance  
Camcorder Handling Precautions  
E
❍ Do not carry the camcorder by the LCD panel or viewfinder.  
❍ Do not leave the camcorder in places subject to high temperatures, such as a sun-  
heated car, and high humidity.  
❍ Do not use the camcorder in places subject to magnetic or electric fields such as  
near the TV transmitters or portable communication devices.  
❍ Do not point the lens or viewfinder at strong light sources. Do not leave the  
camcorder pointed at a bright subject.  
❍ Do not use the camcorder in dusty or sandy places. Dust or sand getting inside the  
cassette or camcorder may cause damage. Dust and sand can also damage the lens.  
Attach the lens cap after use.  
❍ The camcorder is not waterproof. Water, mud or salt getting inside the cassette or  
camcorder may cause damage.  
❍ Be careful of heat generated by lighting equipment.  
❍ Do not disassemble the camcorder. If the camcorder does not function properly,  
consult qualified service personnel.  
❍ Handle the camcorder with care. Do not subject the camcorder to shocks or  
vibration as this may cause damage.  
❍ Avoid sudden changes in temperature. Moving the camcorder rapidly between hot  
and cold temperatures may cause condensation to form on its internal surfaces.  
(
143)  
Storage  
❍ If you do not intend to use the camcorder for a long time, store it in a place free of  
dust, in low humidity, and at temperatures not higher than 86˚F (30˚C).  
❍ After storage, check the functions of your camcorder to make sure that the  
camcorder is still working properly.  
Cleaning  
Camcorder Body and Lens  
❍ Use a soft, dry cloth to clean the camcorder body and lens. Never use chemically  
treated cloth or volatile solvents such as paint thinner.  
LCD Screen  
❍ Clean the LCD screen using a commercially available cleaning cloth for glasses.  
❍ Condensation may form on the surface of the screen when the temperature  
changes suddenly. Wipe it with a soft dry cloth.  
141  
❍ At cold temperatures, the screen may be darker than usual. This is not a  
malfunction. The screen returns to normal when the camcorder warms up.  
E
Viewfinder  
❍ Rotate the viewfinder upward. Remove the protect cover  
and clean the glass with a cotton swab. Reattach the  
protect cover when finished.  
❍ Be careful not to scratch the glass when cleaning.  
Video Heads  
❍ When the playback picture becomes distorted, the video heads need to be cleaned.  
❍ To maintain the best picture quality, we recommend cleaning the video heads  
frequently with the Canon DVM-CL Digital Video Head Cleaning Cassette or a  
commercially available dry cleaning cassette.  
❍ Do not use wet type cleaning cassettes as this may damage the camcorder.  
142  
Condensation  
Moving the camcorder rapidly between hot and cold temperature may cause  
condensation (water droplets) to form on its internal surfaces. Stop using the  
camcorder if condensation is detected. Continued use may damage the camcorder.  
E
Condensation may form in the following cases:  
When the camcorder is moved from an  
air-conditioned room to a warm, humid  
place  
When the camcorder is moved from a  
cold place to a warm room  
When the camcorder is left in a humid  
room  
When a cold room is heated rapidly  
How to avoid condensation:  
❍ Unload the cassette, place the camcorder in an airtight plastic bag and let it adjust  
to temperature changes slowly before removing it from the bag.  
When condensation is detected:  
❍ The camcorder stops operating and the warning message “CONDENSATION HAS  
BEEN DETECTED” appears for approx. 4 seconds and h starts flashing.  
❍ If a cassette is loaded, the warning message “REMOVE THE CASSETTE” appears and  
v starts flashing. Remove the cassette immediately and leave the cassette  
compartment open. Leaving the cassette in the camcorder may damage the tape.  
❍ A cassette cannot be loaded when condensation is detected.  
Resuming use:  
❍ It takes about 1 hour until the water droplets evaporate. After the condensation  
warning stops flashing, wait for 1 more hour before resuming use.  
143  
Using the Camcorder Abroad  
Power Sources  
You can use the compact power adapter to operate the camcorder and to charge  
battery packs in any country with power supply between 100 and 240 V AC, 50/60 Hz.  
Consult the Canon Service Center for information on plug adapters for overseas use.  
E
Playback on a TV Screen  
You can only play back your recordings on TVs with NTSC system. The NTSC system is  
used in the following countries/areas:  
American Samoa, Antigua, Aruba, Bahamas, Barbados, Bermuda, Bolivia, Canada,  
Chile, Columbia, Costa Rica, Cuba, Ecuador, El Salvador, Guam, Guatemala, Greenland,  
Haiti, Honduras, Jamaica, Japan, Korea, Mexico, Micronesia, Myanmar, Nicaragua,  
Panama, Peru, Philippines, Puerto Rico, Saint Kitts and Nevis, Saint Lucia, Saint Vincent  
and the Grenadines, Surinam, Taiwan, Trinidad and Tobago, USA, Venezuela, Virgin  
Islands.  
144  
Troubleshooting  
If you have a problem with your camcorder, refer to this checklist. Consult your dealer  
or a Canon Service Center if the problem persists.  
E
Power Source  
Problem  
Cause  
Solution  
Camcorder will not turn Battery pack is exhausted.  
on.  
Replace or charge the  
battery pack.  
16  
16  
16  
28  
16  
22  
16  
–
Battery pack is not correctly Attach the battery pack  
attached.  
correctly.  
The camcorder switches Battery pack is exhausted.  
off by itself.  
Replace or charge the  
battery pack.  
Power save function has  
been activated.  
Turn on the camcorder.  
Cassette compartment  
will not open.  
Battery pack is exhausted.  
Replace or charge the  
battery pack.  
Cassette compartment cover Open the cassette  
is not fully open.  
compartment cover fully.  
Cassette compartment  
stopped during loading/  
unloading.  
Battery pack is exhausted.  
Replace or charge the  
battery pack.  
The camcorder  
malfunctions.  
Consult a Canon Service  
Center.  
LCD/viewfinder switches Battery pack is exhausted.  
on and off.  
Replace or charge the  
battery pack.  
16  
Recording/Playback  
28  
22  
16  
Buttons will not work.  
Camcorder is not turned on. Turn on the camcorder.  
Cassette is not loaded.  
Load a cassette.  
k flashes on the  
screen.  
Battery pack is exhausted.  
Replace or charge the  
battery pack.  
143  
22  
h flashes on the screen. Condensation is detected.  
See reference page.  
“Remove the cassette”  
appears on the screen.  
Camcorder stopped  
operating to protect the  
tape.  
Unload and reload the  
cassette.  
49  
24  
The wireless controller  
will not work.  
Camcorder and wireless  
controller are not set to the modes.  
same remote sensor mode.  
Change the remote sensor  
Batteries of the wireless  
controller are exhausted.  
Replace the batteries.  
145  
Recording  
Problem  
Cause  
Solution  
Image will not appear  
on the screen.  
Camcorder is not set to  
CAMERA mode.  
Set the camcorder to  
CAMERA mode.  
28  
25  
E
“Set the time zone, date Time zone, date and time  
and time” appears on  
the screen.  
Set the time zone, date and  
time, or replace the backup  
battery and reset the date  
and time.  
are not set, or the backup  
battery is exhausted.  
Pressing the start/stop  
button will not start  
recording.  
Camcorder is turned off.  
Cassette is not loaded.  
Turn on the power.  
Load a cassette.  
28  
22  
22  
Tape reached the end (  
flashes on the screen).  
Rewind the tape or replace  
the cassette.  
Cassette is protected (v  
flashes on the screen).  
Replace the tape or change  
the position of the protect  
switch.  
23  
Camcorder is set to a mode  
Set the camcorder to  
28  
75  
20  
other than the CAMERA mode. CAMERA mode.  
Camcorder will not  
focus.  
Autofocus does not work on Focus manually.  
that subject.  
Viewfinder is not adjusted.  
Adjust the viewfinder with  
the diopter adjustment lever.  
Lens is dirty.  
Clean the lens.  
141  
–
A vertical light bar  
Bright light in a dark scene  
may cause a vertical light  
bar (smear) to appear. This is  
not a malfunction.  
appears on the screen.  
– – –  
– – –  
Sound is distorted or  
recorded in a lower  
volume than the actual  
volume.  
When recording near loud  
sound (such as fireworks,  
drums or concerts), sound  
may become distorted or  
may not be recorded in the  
actual sound level. This is  
not a malfunction.  
–
Viewfinder picture is  
blurred.  
Viewfinder is not adjusted.  
Adjust the viewfinder with  
the diopter adjustment lever.  
20  
37  
Playback  
Pressing the playback  
button does not start  
playback.  
Camcorder is turned off, or is Set the camcorder to PLAY  
not set to PLAY (VCR) mode. (VCR) mode.  
22  
37  
Cassette is not loaded.  
Load a cassette.  
Rewind the tape.  
Tape reached the end (  
flashes on the screen).  
39  
93  
42  
Image will not appear  
on the TV screen.  
[AV/PHONES] is set to  
Set [AV/PHONES] to [AV] in  
the menu.  
[PHONESH] in the menu.  
[AV / DV OUT] is set to  
[ON].  
Set [AV / DV OUT] to [OFF].  
Tape is running, but  
image will not appear  
on the TV screen.  
TV/VIDEO selector on the TV Set the selector to VIDEO.  
is not set to VIDEO.  
142  
91  
Video heads are dirty.  
Clean the video heads.  
You attempted to play back Stop playback/dubbing.  
or dub copyright protected  
tape.  
40  
No sound from the built- Speaker volume is turned  
in speaker. off.  
Adjust the volume with the  
selector dial.  
146  
ZR70 MC ZR65 MC  
Memory Card Operation  
Problem  
Cause  
Solution  
Memory card cannot be Memory card was not facing Turn the memory card over 100  
inserted.  
the correct direction.  
and reinsert it.  
E
Memory card cannot be Memory card is full.  
recorded.  
Replace the memory card or 115  
erase images.  
Memory card is not  
formatted.  
Format the memory card.  
128  
Memory card is not inserted. Insert a memory card.  
100  
102  
File number reached  
maximum value.  
Set [FILE NUMBERS] to  
[RESET] and insert a new  
memory card.  
SD Memory Card is  
protected.  
Change the position of the  
protect switch.  
100  
111  
Memory card cannot be Camcorder is not set to  
Set the camcorder to CARD  
PLAY (VCR) mode.  
played back.  
CARD PLAY (VCR) mode.  
Memory card is not inserted. Insert a memory card.  
100  
114  
100  
Image cannot be erased. Image is protected.  
Cancel the protection.  
SD memory card is  
protected.  
Change the position of the  
protect switch.  
flashes red.  
Card error occurred.  
Turn off the camcorder.  
Remove and reinsert the  
memory card. Format the  
memory card if flashing  
persists.  
128  
147  
(Availability differs from area to area)  
System Diagram  
E
WS-20 Wrist Strap  
ZR70 MC  
WA-30.5 Wide  
Attachment  
SS-800 Shoulder Strap  
ZR70 MC ZR65 MC  
WL-D79 Wireless  
Controller  
ZR60 WL-D80  
Wireless Controller  
BP-500 Series  
Battery Pack  
WD-30.5 Wide-  
converter  
CG-570  
Battery Charger  
CB-570  
Car Battery Cable  
MiniDV  
TL-30.5 Tele-  
converter  
Video  
Cassette  
CA-570 Compact  
Power Adapter  
FS-30.5U  
Filter Set  
BP-500 Series  
Battery Pack  
S-150 S-video Cable  
VL-3 Video Light  
ZR70 MC  
ZR70 MC  
TV  
STV-250N  
Stereo Video Cable  
VCR  
DM-50 Directional  
Stereo Microphone  
Commercially available  
DV Cable  
Digital Device  
ZR70 MC ZR65 MC  
PC Card Adapter  
USB Reader/Writer  
FD Adapter  
BP-900 Series  
Battery Pack*  
VL-10Li  
SD Memory Card  
MultiMediaCard  
Battery  
Video Light  
Stereo Microphone  
(commercially  
available)  
Computer  
IFC-300PCU  
USB Cable  
Bubble Jet Printer  
with direct print  
function  
SC-1000 Soft  
Carrying Case  
SC-A50 Soft  
Carrying Case  
* Charging with the CA-920 Compact Power Adapter or CH-910 Dual Battery  
Charger/Holder (both optional)  
148  
Optional Accessories  
Call or visit your local retailer/dealer for genuine Canon video accessories. You can also  
obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040,  
Canon U.S.A. Information Center.  
E
BP-500 Series Battery Packs  
BP-512  
BP-522  
BP-535  
When you need extra battery packs, select from  
the following: BP-511, BP-512, BP-522 or BP-535.  
CG-570 Battery Charger  
The battery charger can be used with the  
supplied CA-570 Compact Power Adapter or the  
optional CB-570 Car Battery Cable to charge BP-  
500 series battery packs.  
Battery Pack  
Charging Time  
55 min.  
BP-508 (ZR65 MC/ZR60)  
BP-512 (ZR70 MC/Optional)  
BP-511 (Optional)  
BP-522 (Optional)  
BP-535 (Optional)  
95 min.  
95 min.  
140 min.  
205 min.  
CB-570 Car Battery Cable  
Use the car battery cable with the CG-570  
Battery Charger to charge battery packs on the  
move. The car battery cable plugs into your  
car’s cigarette lighter and runs off a 12-24 V DC  
negative ground battery.  
TL-30.5 Tele-converter  
This tele-converter lens increases the focal  
length of the camcorder lens by a factor of 1.9.  
• The image stabilizer is not as effective when  
the tele-converter is attached.  
• The image quality may be degraded at the telephoto side.  
• The minimum focusing distance with the Tele-converter is 13.1 ft (4 m); 1.6 in. (4 cm)  
on maximum wide angle.  
149  
WD-30.5 Wide-converter  
This lens decreases focal length by a factor of  
0.7, giving you a wide perspective for indoor  
shots or panoramic views.  
E
FS-30.5U Filter Set  
Neutral density and MC protector filters help  
you to control difficult lighting conditions.  
VL-10Li Battery Video Light  
This compact yet powerful video light can be  
used for both indoor and outdoor shooting.  
The video light is powered by BP-900 series  
battery packs.  
• Approximate usage time: BP-915: 60 min., BP-930: 120 min., BP-945: 170 min.  
• BP-900 series battery packs are charged with the CA-920 Compact Power Adapter  
(optional).  
ZR70 MC  
VL-3 Video Light  
This video light enables you to record brightly  
in color even in dark places. It attaches to the  
camcorder’s advanced accessory shoe for cable-  
free operation.  
ZR70 MC  
DM-50 Directional Stereo  
Microphone  
This highly sensitive, super-directional  
microphone attaches to the camcorder’s  
advanced accessory shoe. It can be used as  
directional microphone (monaural) or stereo  
microphone.  
WS-20 Wrist Strap  
Use this for extra additional protection for  
active shooting.  
150  
SC-1000 Soft Carrying Case  
A handy camcorder bag with padded  
compartments and plenty of space for  
accessories.  
E
SC-A50 Soft Carrying Case  
This lightweight bag keeps the camcorder  
within easy reach without weighing you down  
or getting in the way.  
E
N
N
This mark identifies genuine Canon video accessories. When you  
use Canon video equipment, we recommend Canon-brand  
accessories or products bearing the same mark.  
O
U
N
IN  
A
C
E
Y
I
D
E
R
O S  
O
S
A
C
E
Provided Accessories:  
WL-D79 Wireless Controller (ZR70 MC/ZR65 MC)  
WL-D80 Wireless Controller (ZR60)  
SS-800 Shoulder Strap  
D83-0622-000  
D83-0652-000  
D81-1430-000  
D52-0220-000  
8468A002AA  
6760A002AA  
D85-1360-000  
3067A002AA (D82-0590-201)  
6906A001AA  
D55-0170-000  
Lens Cap  
CA-570 Compact Power Adapter  
BP-512 Battery Pack (ZR70 MC)  
BP-508 Battery Pack (ZR65 MC/ZR60)  
STV-250N Stereo Video Cable  
IFC-300PCU USB Cable (ZR70 MC/ZR65 MC)  
WA-30.5 Wide Attachment  
Optional Accessories:  
BP-511 Battery Pack  
BP-522 Battery Pack  
3055A002AA (D85-1112-201)  
3174A002AA (D85-1122-201)  
6741A002AA  
BP-535 Battery Pack  
SC-1000 Soft Carrying Case  
SC-A50 Soft Carrying Case  
WD-30.5 Wide-converter  
TL-30.5 Tele-converter  
F-30.5U Filter Set  
3083A002AA (D81-1200-201)  
D81-1302-201  
6739A002AA  
6740A002AA  
6738A002AA  
DM-50 Directional Stereo Microphone  
VL-3 Video Light  
VL-10Li Battery Video Light  
JR 7.2V 10WF Halogen Bulb  
WS-20 Wrist Strap  
3176A002AA (D84-0120-201)  
3175A002AA (D86-0121-201)  
3140A002AA (D86-0081-201)  
3141A002AA (D86-0090-201)  
3118A002AA (D81-0190-202)  
3134A002AA (D36-0032-201)  
DVM-CL DV Cleaning Cassette  
151  
Specifications  
ZR70 MC/ZR65 MC/ZR60  
E
Power supply (rated):  
7.4 V DC  
Power consumption  
(AF turned on):  
2.9 W (Using viewfinder), 3.8 W (Using LCD screen)  
Television system:  
EIA standard (525 lines, 60 fields) NTSC color signal  
Video recording system:  
2 rotary heads, helical scanning DV system (Consumer digital VCR  
SD system); Digital component recording  
Audio recording system:  
Image sensor:  
PCM digital sound: 16 bit (48 kHz/2 ch); 12 bit (32 kHz/4 ch)  
1/6“ CCD (charge coupled device), approx. 680,000 pixels  
(Effective pixels: tape: approx. 340,000 pixels, card*1: approx.  
447,000 pixels)  
Tape format:  
Tape speed:  
Videocassettes bearing the “MiniDV” mark.  
SP: 0.74 ips (18.81 mm/s), LP: 0.49 ips (12.56 mm/s)  
SP: 80 min., LP: 120 min.  
Maximum recording time  
(80 min. cassette):  
Fast forward/rewind time:  
Lens:  
Approx. 2 min. 20 sec. (with a 60 min. cassette)  
ZR70 MC: F1.6-3.6, 22x power zoom, f=2.8-61.6 mm;  
ZR65 MC: F1.6-3.2, 20x power zoom, f=2.8-56 mm;  
ZR60 MC: F1.6-2.9, 18x power zoom, f=2.8-50.4 mm  
Focusing system:  
TTL autofocus, manual focusing possible  
Minimum focusing distance: 3.3 ft. (1 m), 0.39 in. (1 cm) on maximum wide angle  
Maximum shutter speed:  
Minimum illumination:  
1/2,000 sec. (1/250 sec. when using a memory card)  
1.6 lx (using the Night mode in CAMERA mode)  
Recommended illumination: More than 100 lx  
Filter diameter:  
Viewfinder:  
30.5 mm  
0.33 in., TFT color LCD, approx. 113,000 pixels  
2.5 in., TFT color, approx. 112,000 pixels  
Stereo electret condenser microphone  
SD Memory Card, MultiMediaCard  
LCD screen:  
Microphone:  
Recording media*1:  
Number of recording pixels*1: Still image: 1024 x 768, 640 x 480 pixels  
Movie*2: 320 x 240 pixels (approx. 10 sec.), 160 x 120 pixels  
(approx. 30 sec.), 15 frames/sec.  
The figures in brackets represent the maximum length of one  
movie clip.  
Estimated SD Memory Card 1024 x 768: Superfine: 14 images/Fine: 20 images/Normal 39  
SDC-8M capacities*1:  
images;  
640 x 480: Superfine: 35 images/Fine 52 images/Normal 86 images  
The actual number varies according to the images. Sample images recorded on the supplied SD  
Memory Card are to be included in the total number.  
File format*1:  
Design rule for Camera File system (DCF), Exif 2.2 compliant,  
Digital Print Order Format (DPOF) compliant (still images only)  
This camcorder supports Exif 2.2 (also called “Exif Print”). Exif Print is a standard for enhancing the  
communication between camcorders and printers. By connecting to an Exif Print-compliant printer,  
the camcorder’s image data at the time of shooting is used and optimized, yielding extremely high  
quality prints.  
Image format*1:  
Still image: JPEG (Compression mode: Superfine, Fine, Normal),  
Movie: Motion JPEG  
*1 ZR70 MC/ZR65 MC only *2 ZR70 MC only  
152  
USB terminal*1:  
mini-B  
DV terminal input/output:  
AV terminal input/output:  
Special 4-pin connector (IEEE 1394 compliant)  
ø3.5 mm minijack  
Audio input: -10 dBV/40 kohms or more  
Audio output: -10 dBV (47 kohm load)/3 kohms or less  
E
Video:  
1 Vp-p/75 ohms unbalanced  
S-video terminal  
input/output:  
1 Vp-p/75 ohms (Y signal), 0.286 Vp-p/75 ohms (C signal)  
MIC terminal input:  
ø3.5 mm stereo mini-jack  
–57 dBV (with 600 ohm mic)/5 kohms or more  
Headphone terminal:  
Operating temperatures:  
Dimensions:  
ø3.5 mm stereo minijack  
32 – 104˚F (0 – 40˚C)  
4.1 × 2.3 × 5.8 in. (103 × 58 × 147 mm)  
ZR70 MC: 1.2 lb. (525 g), ZR65 MC/ZR60: 1.2 lb. (520 g)  
Weight:  
*1 ZR70 MC/ZR65 MC only  
CA-570 Compact Power Adapter  
Power supply:  
Power consumption:  
Rated output:  
100 – 240 V AC, 50/60 Hz  
17 W  
8.4 V DC, 1.5 A  
Operating temperature:  
Dimensions:  
32 – 104˚F (0 – 40˚C)  
2.1 × 3.5 × 1.1 in. (52 × 90 × 29 mm)  
4.8 oz. (135 g)  
Weight:  
BP-512/BP-508 Battery Pack  
Battery type:  
Rechargeable Lithium Ion Battery  
Rated voltage:  
Operating temperature:  
Battery capacity:  
Dimensions:  
7.4 V DC  
32 – 104˚F (0 – 40˚C)  
BP-512: 1100 mAh, BP-508: 800 mAh  
1.5 × 0.83 × 2.2 in. (38 × 21 × 55 mm)  
BP-512: 2.5 oz. (70g), BP-508: 2.3 oz. (65g)  
Weight:  
SDC-8M SD Memory Card  
Capacity:  
8 MB  
Interface:  
SD Memory Card standard  
32 – 104˚F (0 – 40˚C)  
1.3 × 0.94 × 0.08 in. (32 × 24 × 2.1 mm)  
0.07 oz. (2 g)  
Operating temperature:  
Dimensions:  
Weight:  
Weight and dimensions are approximate. Errors and omissions excepted. Subject to  
change without notice.  
153  
Index  
12bit audio . . . . . . . . . . . . . . . . . . 98  
16:9 wide screen . . . . . . . . . . . . . . 52  
6-second auto date . . . . . . . . . . . . 84  
Digital zoom . . . . . . . . . . . . . . . . . 30  
Direct print function *2. . . . . . . . 118  
DV dubbing. . . . . . . . . . . . . . . . . . 90  
DV terminal. . . . . . . . . . . . . . . 88, 99  
E
A
Abroad, using the camcorder . . . 144  
Accessories. . . . . . . . . . . . . . . . 9, 149  
Accessory shoe . . . . . . . . . . . . . . 150  
Advanced accessory shoe *1 . . . . . 73  
Analog line-in . . . . . . . . . . . . . . . . 89  
Analog-digital converter. . . . . . . . 92  
Assist lamp *1 . . . . . . . . . . . . . . . . 59  
Audio dubbing . . . . . . . . . . . . . . . 96  
Audio mode . . . . . . . . . . . . . . . . . 71  
Auto . . . . . . . . . . . . . . . . . . . . . . . 57  
Autofocus . . . . . . . . . . . . . . . . . . . 75  
AV insert . . . . . . . . . . . . . . . . . . . . 94  
AV/DV . . . . . . . . . . . . . . . . . . . . . 92  
AV/headphones terminal . . . . 39, 41  
E
Easy recording. . . . . . . . . . . . . . . . 57  
Effects . . . . . . . . . . . . . . . . . . . . . . 65  
Erasing still images *2 . . . . . . . . . 115  
Exposure . . . . . . . . . . . . . . . . . . . . 77  
F
Faders . . . . . . . . . . . . . . . . . . . . . . 62  
Fast forward . . . . . . . . . . . . . . . . . 37  
File numbers *2 . . . . . . . . . . . . . . 103  
Focusing . . . . . . . . . . . . . . . . . . . . 75  
Formatting *2 . . . . . . . . . . . . . . . 128  
G
Grip belt . . . . . . . . . . . . . . . . . . . . 20  
B
Backup battery . . . . . . . . . . . . . . . 19  
Battery charger . . . . . . . . . . . . . . 149  
Battery pack . . . . . . . . . . . . . . . . . 16  
Beep . . . . . . . . . . . . . . . . . . . . . . . 52  
Brightness . . . . . . . . . . . . . . . . . . . 33  
H
Headphones . . . . . . . . . . . . . . . . . 39  
I
Image quality *2 . . . . . . . . . . . . . 101  
Image stabilizer. . . . . . . . . . . . . . . 69  
Index screen *2 . . . . . . . . . . . . . . 112  
C
Card animation *2. . . . . . . . . . . . 123  
Card mix *2 . . . . . . . . . . . . . . . . . 122  
Computer . . . . . . . . . . . . . . . 99, 129  
Condensation . . . . . . . . . . . . . . . 143  
Connections - TV. . . . . . . . . . . . . . 41  
Connections - VCR. . . . . . . . . . . . . 41  
Copyright signals. . . . . . . . . . . . . . 91  
Copying still images*2. . . . . . . . . 126  
L
LCD mirror mode . . . . . . . . . . . . . 33  
LCD screen. . . . . . . . . . . . . . . . . . . 32  
Lens cap . . . . . . . . . . . . . . . . . . . . 20  
Light-up buttons *1. . . . . . . . . . . . 51  
Low light mode. . . . . . . . . . . . . . . 58  
Low light plus mode *1. . . . . . . . . 59  
LP mode . . . . . . . . . . . . . . . . . . . . 54  
D
Data code . . . . . . . . . . . . . . . . . . . 83  
Date and time. . . . . . . . . . . . . . . . 25  
Date search . . . . . . . . . . . . . . . . . . 85  
Demo mode . . . . . . . . . . . . . . . . . 53  
Digital effects . . . . . . . . . . . . . . . . 61  
M
Magnifying the image . . . . . . . . . 82  
Maintenance . . . . . . . . . . . . . . . . 141  
Manual focus . . . . . . . . . . . . . . . . 75  
Memory card *2 . . . . . . . . . . . . . 101  
1
2
ZR70 MC  
ZR70 MC ZR65 MC  
*
, *  
154  
Menus . . . . . . . . . . . . . . . . . . . . . . 44  
Microphone. . . . . . . . . . . . . . . . . . 71  
MIC terminal . . . . . . . . . . . . . . . . . 71  
Movie size *1. . . . . . . . . . . . . . . . 102  
MultiMediaCard *2 . . . . . . . . . . . 101  
Multi-image screen . . . . . . . . . . . . 67  
My Camera settings . . . . . . . . . . . 50  
Search select . . . . . . . . . . . . . . . . . 85  
Self-timer . . . . . . . . . . . . . . . . . . . 70  
Shutter sound *2 . . . . . . . . . . . . . 105  
Shutter speed . . . . . . . . . . . . . . . . 78  
Slide show *2. . . . . . . . . . . . . . . . 112  
SP mode . . . . . . . . . . . . . . . . . . . . 54  
Speaker . . . . . . . . . . . . . . . . . . . . . 39  
Sports mode . . . . . . . . . . . . . . . . . 58  
Spotlight mode . . . . . . . . . . . . . . . 58  
Still image quality *2. . . . . . . . . . 101  
Still image size *2 . . . . . . . . . . . . 101  
Stitch Assist mode *2. . . . . . . . . . 107  
Super Night mode *1 . . . . . . . . . . 59  
S-video/S1-video . . . . . . . . . . . . . . 41  
E
N
Night mode. . . . . . . . . . . . . . . . . . 59  
O
Output channel. . . . . . . . . . . . . . . 43  
P
Photo search . . . . . . . . . . . . . . . . . 85  
Playback - Memory card *2 . . . . . 111  
Playback - Tape . . . . . . . . . . . . . . . 37  
Playback pause . . . . . . . . . . . . . . . 38  
Portrait mode . . . . . . . . . . . . . . . . 58  
Power adapter . . . . . . . . . . . . . . . 15  
Print order *2 . . . . . . . . . . . . . . . 116  
Protect *2 . . . . . . . . . . . . . . . . . . 114  
T
Tape protection. . . . . . . . . . . . . . . 23  
Telephoto . . . . . . . . . . . . . . . . . . . 30  
Time code . . . . . . . . . . . . . . . . . . . 86  
Time zone . . . . . . . . . . . . . . . . . . . 25  
Tripod . . . . . . . . . . . . . . . . . . . . . . 36  
Troubleshooting . . . . . . . . . . . . . 145  
TV Screen. . . . . . . . . . . . . . . . 41, 134  
R
U
Recording to a VCR. . . . . . . . . . . . 87  
Record pause mode . . . . . . . . . . . 29  
Record review . . . . . . . . . . . . . . . . 35  
Record search . . . . . . . . . . . . . . . . 35  
Recording Movies (tape). . . . . . . . 28  
Recording Movies  
USB terminal *2. . . . . . . . . . . . . . 129  
V
Video. . . . . . . . . . . . . . . . . . . . . . . 41  
Video heads. . . . . . . . . . . . . . . . . 142  
Video ID-1 system . . . . . . . . . . . . . 41  
Video light. . . . . . . . . . . . . . . 73, 150  
Videocassettes. . . . . . . . . . . . . . . . 22  
Viewfinder . . . . . . . . . . . . . . . . . . 20  
(memory card) *1 . . . . . . . . . . . 109  
Recording Still Images (tape) . . . . 55  
Recording Still Images  
(memory card) *2 . . . . . . . . . . . 104  
Recording programs . . . . . . . . . . . 57  
Remote sensor. . . . . . . . . . . . . . . . 24  
Rewind . . . . . . . . . . . . . . . . . . . . . 37  
W
White balance. . . . . . . . . . . . . . . . 80  
Wide screen. . . . . . . . . . . . . . . . . . 52  
Wireless controller . . . . . . . . . . . . 24  
S
S1 video terminal . . . . . . . . . . . . . 41  
Sample images *2 . . . . . . . . . . . . 132  
Sand & Snow mode. . . . . . . . . . . . 58  
Screen displays . . . . . . . . . . . . . . 134  
SD Memory Card *2. . . . . . . . . . . 101  
Z
Zero set memory. . . . . . . . . . . . . . 86  
Zooming . . . . . . . . . . . . . . . . . . . . 30  
1
2
ZR70 MC  
ZR70 MC ZR65 MC  
*
, *  
155  
U.S.A.  
®
CANON ZR70 MC/ZR65 MC/ZR60 DIGITAL VIDEO CAMCORDER LIMITED  
WARRANTY  
E
The limited warranty set forth below is given by Canon U.S.A., Inc. (“CUSA”) with respect to each Canon ZR70 MC/  
ZR65 MC/ZR60 Digital Video Camcorder (“DV Camcorder”) purchased and used in the United States.  
Each Canon DV Camcorder, when delivered to you in new condition in its original container, is warranted against defective  
material or workmanship as follows: for a period of one (1) year from the date of original purchase (three (3) months in the  
case of the video head part), defective parts or DV Camcorders returned to a CUSA factory service center (“CUSA Center”)  
or an authorized DV Camcorder service facility (“Service Facility”), and proven to be defective upon inspection, will be  
repaired or exchanged for new or comparable rebuilt parts or DV Camcorders. The warranty period for repaired or  
replacement parts or DV Camcorders shall begin upon shipment of the same, but shall in no event exceed the original  
warranty period of the defective part or DV Camcorder.  
Non-Canon brand peripheral equipment and software which may be distributed with Canon DV Camcorders are  
sold “AS IS”, without warranty of any kind by CUSA, including any implied warranty regarding merchantability  
or fitness for a particular purpose. The sole warranty with respect to such non-Canon brand items is given by  
the manufacturer or producer thereof.  
CUSA shall have no responsibility under this limited warranty for use of Canon DV Camcorders in conjunction with  
incompatible peripheral equipment and incompatible software.  
In order to obtain warranty service, contact the authorized Canon retail dealer from whom you purchased the DV  
Camcorder or call the CANON INFORMATION CENTER AT 1-800-828-4040 (which is open from 9:00 a.m. to 5:00 p.m.  
(E.S.T.), Monday through Friday, excluding holidays). Have your unit serial number and your date of purchase available  
when you make the call to expedite service. In either case you will be directed to ship the DV Camcorder, postage prepaid,  
to the CUSA Center or Service Facility nearest to you. You must include a copy of the proof of purchase (bill of sale) and a  
complete explanation of the problem. DV Camcorders covered by this limited warranty will be repaired and returned to you  
without charge by the CUSA Center or the Service Facility. Repairs not under warranty will be at such cost as the CUSA  
Center or Service Facility may from time to time generally establish.  
This limited warranty covers all defects encountered in normal use of the DV Camcorder, and does not apply in the  
following cases:  
(a) Loss of or damage to the DV Camcorder due to abuse, mishandling, improper packaging by you, alteration, accident,  
leaking batteries, exterior nicks, scratches or dents, electrical current fluctuations, failure to follow operating  
instructions, maintenance and environmental instructions prescribed in CUSA’s instruction manual, or service performed  
by other than a CUSA Center or Service Facility.  
(b) Use of parts or supplies (other than those sold by CUSA) which cause damage to the DV Camcorder or cause  
abnormally frequent service calls or service problems.  
(c) If any DV Camcorder has had its serial number or dating altered or removed.  
This limited warranty does not apply to accessories or consumables for the DV Camcorder, which are sold “AS IS”, without  
warranty of any kind by CUSA.  
NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE, APPLIES TO THE DV CAMCORDER AFTER THE APPLICABLE PERIOD OF EXPRESS  
WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED  
ABOVE, GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THE DV CAMCORDER SHALL BIND  
CUSA. (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE  
ABOVE LIMITATION MAY NOT APPLY TO YOU) CUSA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS,  
EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OF DATA, OR ANY OTHER  
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE  
DV CAMCORDER, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CUSA HAS  
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CUSA  
BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE DV CAMCORDER SOLD BY CUSA AND CAUSING  
THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS,  
DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF  
USE, MISUSE OR INABILITY TO USE THE DV CAMCORDER NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CUSA.  
(SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,  
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.) THIS LIMITED WARRANTY SHALL NOT EXTEND TO  
ANYONE OTHER THAN THE ORIGINAL PURCHASER OF ANY DV CAMCORDER, OR THE PERSON FOR WHOM IT  
WAS PURCHASED AS A GIFT, AND STATES YOUR EXCLUSIVE REMEDY.  
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Canon U.S.A., Inc.  
One Canon Plaza  
Lake Success, New York 11042  
156  
CANADA  
CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY  
The limited warranty set forth below is given by Canon Canada Inc. (“Canon Canada”) with respect to Canon digital video equipment purchased  
in Canada. This limited warranty is only effective upon presentation of a bill of sale or other proof of purchase for this Canon digital video  
equipment to a Canon Service Facility when repairs are required.  
E
Canon consumer video digital equipment is warranted under normal, non-commercial, personal use, against defective materials or workmanship  
as follows:  
Parts: Defective parts will be exchanged for new parts or, at Canon Canada’s option, comparable rebuilt parts for a period of one year from the  
date of original purchase, except Video Heads which will be exchanged for a period of 3 months from the date of purchase.  
Labour: For a period of one year from the date of original purchase, labour will be provided free of charge by our Canon Service Facilities in  
Canada.  
This limited warranty covers all defects except where:  
(a) The loss or damage to the product results from:  
i)  
accident, natural disaster, mishandling, abuse, neglect, unauthorized product modification or failure to follow instructions contained in  
the instruction manual;  
ii) the use of accessories, attachments, products, supplies, parts or devices with this Canon product that do not conform to Canon  
specifications or that cause abnormally frequent service problems;  
iii) repairs or services performed by any party other than a Canon Service Facility;  
iv) defective batteries or any exposure to water, sand or dirt;  
v) shipping (claim must be presented to the shipper);  
(b) Any serial number on the video equipment is altered or removed.  
(c) The digital video equipment is used for commercial, professional or industrial purposes.  
This limited warranty does not cover the cabinet (exterior finish) of the digital video equipment, video cassette tapes, head cleanings, nor does it  
apply to digital video equipment purchased outside Canada.  
TO OBTAIN WARRANTY SERVICE  
Ship your Canon digital video equipment in its original carton, box or equivalent, properly packed, fully insured with shipping charges prepaid,  
together with a copy of your bill of sale or other proof of purchase and a description of the problem to any of the Canon Service Facilities in  
Canada.  
LIMITATIONS  
Except as otherwise required by applicable legislation, this warranty is in lieu of all other warranties, conditions, guarantees or representations,  
express or implied, statutory or otherwise, relative to this Canon product, including implied warranties or conditions of merchantability or fitness  
for a particular purpose.  
Canon Canada assumes no liability for special, consequential or incidental damages or loss that may arise, whether on account of negligence or  
otherwise, from the use, misuse or inability to use this Canon product (including loss of profit, revenue, video tapes or enjoyment) or from failure  
to conform to any express or implied warranties, conditions, guarantees or representations. Any recovery under this limited warranty shall not  
exceed the purchase price of the product. Canon Canada does not assume or authorize any other person to assume for Canon Canada any other  
liability with respect to this Canon product.  
This warranty does not extend to any person other than the original purchaser of this Canon product or the person for whom it was purchased as  
a gift and states your exclusive remedy.  
NOTICE TO CONSUMER  
If you plan to take important videos or if the product has not been used for some time, please check all functions with the instruction book  
before using it.  
157  

Audiovox VBP500 User Manual
Blaupunkt CARACAS RCR 27 User Manual
Cecilware J 120 User Manual
Crown XTI2 SERIES XTI 1002 User Manual
Cuisinart DLC XP User Manual
Elta 7173N2 User Manual
Gitzo Explorer Series 2 G2220 User Manual
Gitzo GT1530 User Manual
Hypertec PerfectSkin N12308NHY User Manual
Jensen JAN139 User Manual