Bunn TCD 1 User Manual

TCD-1  
TCD-2  
INSTALLATION & OPERATING MANUAL  
With ILLUSTRATED PARTS  
NOTE: LIFT THE DISPENSER USING THE HANDLES ONLY. DO NOT LIFT THE DISPENSER FROM THE BOTTOM.  
BUNN-O-MATIC CORPORATION  
POST OFFICE BOX 3227  
SPRINGFIELD, ILLINOIS 62708-3227  
PHONE: (217) 529-6601 FAX: (217) 529-6644  
34106.0001L 11/06 © 2004 Bunn-O-Matic Corporation  
INTRODUCTION  
These dispensers are designed to mix liquid tea concentrate with water to produce iced tea by the glass or pitcher. The  
concentrate can be stored either inside the dispenser, or outside with a hose connection to the dispenser. The dispenser  
must be placed on a sturdy counter or shelf.  
PLUMBING REQUIREMENTS  
This dispenser must be connected to a cold water system with operating pressure between 30 and 90 psi  
(138 and 620 kPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the  
dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi  
(345 kPa). The water inlet fitting is 1/4" flare.  
NOTE - Bunn-O-Matic recommends 1/4" copper (or 3/8" braided flex) tubing for all installations from the 1⁄2"  
water supply line. A tight coil of copper tubing in the water line will facilitate moving the dispenser to clean the  
counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the dispenser. The size and  
shape of the hole made in the supply line by this type of device may restrict water flow.  
This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials  
and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the  
Food and Drug Administration (FDA). For models installed outside the U.S.A., you must comply  
with the applicable Plumbing/Sanitation Code for your area.  
USER NOTICES  
Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should  
be kept in good condition. Replace any unreadable or damaged labels.  
This equipment must be installed to comply with the  
PRESSURE REGULATOR ADJUSTMENT  
Basic Plumbing Code of the Building Officials and  
Code Administrators International, Inc. (BOCA) and  
1. Pull Knob out to unlock.  
the Food Service Sanitation Manual of the Food and  
2. Adjust to 20 psi while faucet  
is open, dispensing product.  
3. Push knob in to lock.  
Drug Administration (FDA). For models installed  
outside the U.S.A., comply with the applicable  
Plumbing /SanitationCode.  
00656.0000  
38465.0000  
38130.0000  
38466.0000  
34106.1 060706  
3
SET UP AND OPERATING PROCEDURES  
1. Remove dispenser from the box and place on a sturdy, level counter.  
2. Remove the brass cap and any packing material from the end of the water inlet fitting located on the rear of  
the dispenser.  
3. Attach the 1/4" "L" tube and water strainer to the water inlet fitting, tighten all flare nuts.  
NOTE: The flow direction arrow on the strainer must point towards the dispenser.  
4. Attach a 1/4" water line to the water strainer. This supply line must have at least 30 psi of pressure.  
5. Using a screwdriver, turn the adjustment screw clockwise until the screw contacts the seat (DO NOT OVER-  
TIGHTEN THIS SCREW!).  
6. Turn on the water supply and open the water inlet valve on the rear of the dispenser and check for leaks in  
the system.  
7. Place a container under faucet(s); fully open the faucet(s) for approximately 10 seconds to remove all the air  
out of the lines, then close the faucet(s). Discard the water.  
8. Connect the proper BIB (Bag in a Box) adapter(s) to the concentrate inlet tube(s) and clamp. If bottle con-  
centrate is used, connect the stainless formed tube(s) to the inlet hose(s) and clamp.  
9. Attach the connector(s) to the BIB, or insert the bottle adapter into the bottle(s).  
10. Place the concentrate container(s) in the location they will be used for normal operations.  
a. In the dispenser housing: Coil the tube in the dispenser and place the BIB (bottle) on top of the coiled  
tubing with the connector facing down, under the bag.  
b. Under the counter: Place the BIB under the counter and rout the tubing to the dispenser, avoiding sharp  
bends and kinks. Cut off excess tubing to keep the over length of tubing to minimum.  
NOTE: It is critical that the dispenser is upright and the concentrate container(s) be in the proper location and  
orientation that they will be during normal operation, before making any strength adjustments.  
11. Slide the dispenser to the edge of the counter to gain access to the adjustment screw from the bottom.  
12. Turn the adjustment screw approximately 1/2 turn counterclockwise.  
13. Place a container under the faucet(s) and open faucet(s) until the entire concentrate line(s) fill and tea is  
dispensed for approximately 5 seconds. Close the faucet(s). Discard this solution.  
14. Place a glass under the faucet and open to fill the glass. Adjust the screw to achieve the desired strength  
of tea. To increase the amount of concentrate (stronger tea), turn the adjustment screw counterclockwise  
slightly (1/16 to 1/8 of a turn at a time). To reduce the amount of concentrate (weaker tea), turn the adjust-  
ment screw clockwise slightly (1/16 to 1/8 of a turn at a time).  
15. Dispense a couple of 8 ounce glasses of tea after each adjustment and test for taste or color. Continue this  
process until the taste or color profile is achieved.  
NOTE: The ratio adjustment setting is very sensitive. Make very small adjustments with the screw, then taste or  
color check the results. You do not have to turn the screw very much to change the ratio.  
16. Once the desired ratio of concentrate to water has been set, slide the dispenser back to the desired location  
on the counter top. For under counter BIB’s, make sure the tubes do not get kinked, when the dispenser is  
slid back into place.  
The dispenser is now ready for use.  
34106.1 100506  
4
DISPENSER CLEANING AND SANITIZING  
Daily Cleaning:  
1. Turn handle on rear of dispenser to shut off the water supply.  
2. Open the faucet to relieve pressure in the system.  
3. Since the bag connector(s) have an internal shut off valve, it will be necessary to prop the valve open during clean-  
ing.  
NOTE: Cutting off the mating connector of an empty concentrate bag works well for this. Keep this mating end for future  
cleanings of the system.  
4. Turn on water supply to the dispenser.  
5. Place the open bag connector into a 1/2 gallon container of dish soap and warm to hot water (130° F/54° C).  
6. Place a large container under dispenser faucet.  
7. Open faucet until the soap/water mixture in the container is empty.  
8. After the soap mixture has been flushed through the system, fill the container with warm to hot tap water only (no  
soap) and repeat steps 5 thru 7 until all soap has been flushed from the system.  
9. Remove the mating end of connector and attach dispenser’s connector to a Bag In a Box and dispense several cups  
to prime the concentrate line or until consistency of the product is correct.  
10. Wash the entire outside surface of dispenser with a clean, damp cloth.  
NOTE: When the system is not in use for extended periods of time (nights, weekends, etc.), turn the water supply valve  
off.  
Weekly Cleaning:  
1. Turn handle on rear of dispenser to shut off the water supply.  
2. Open the faucet to relieve pressure in the system.  
On models with chrome nut (Complete Step 3, then skip to Step 6):  
On models with wing nut (Skip Step 3 - Start at Step 4):  
3. Unscrew the faucet bonnet (a) and remove all faucet components, leaving the faucet body (b) in place on the venturi  
assembly.  
4. Twist the faucet wing nut in a clockwise direction and remove faucet from the dispenser.  
5. Remove and clean the O-ring (Optional).  
a. Remove the o-ring from the venturi assembly nozzle. Be very careful when removing this o-ring.  
Do Not scratch or nick the o-rings sealing surface when removing.  
b. Clean the groove and o-ring with the same solutions as used to clean the faucet, Step 6.  
c. When finished, slide the o-ring back into the groove on the venturi nozzle.  
6. Sanitizing the faucet:  
This procedure requires three cleaning solutions of approximately ½ gal each, a mild detergent and warm  
water solution, clean hot water only and a warm chlorine solution (at least 50 ppm of chlorine at 75° F [24°  
C]). NOTE: DO NOT use full strength bleach.  
a
b
a. Disassemble the faucet.  
b. Thoroughly wash all faucet parts in the mild detergent solution.  
c. Rinse the parts in hot water.  
d. Sanitize the parts by soaking for one minute in the warm chlorine solution.  
e. Re-rinse the parts in hot water to remove all the chlorine solution.  
f. Reassemble the faucet and attach it to the dispenser.  
7. Sanitizing the BIB connector, tubing and metering valve:  
This procedure requires a 1/2 gallon container of sanitizing solution, (100 ppm of chlorine at 100° F (38° C) water).  
a. Since the bag connector(s) have an internal shut off valve, it will be necessary to prop the valve open during clean-  
ing. NOTE: Cutting off the mating connector of an empty concentrate bag works well for this. Keep this mating end for  
future cleanings of the system.  
b. Turn on water supply to the dispenser.  
c. Place open bag connector into the 1/2 gallon container of sanitizing solution.  
d. Place a large container under dispenser faucet.  
e. Open faucet until the chlorine mixture in the container is empty.  
f. Allow dispenser to sit overnight before flushing sanitizer out of the system.  
g. Flush system by filling a container with warm to hot tap water only (no chlorine) and opening the faucet - until all  
chlorine has been flushed from the system.  
8. Remove the mating end of connector and attach dispenser’s connector to a Bag In a Box and dispense several cups  
to prime the concentrate line or until consistency of the product is correct.  
34106.1 100506  
5
TCD-1  
TCD-2  
REPLACEMENT PARTS (TCD-1)  
60  
61  
63  
62  
61  
47  
.375" BIB Adapter  
Concentrate Bottle Tube  
23  
46  
27  
28  
29  
50  
21  
51  
20  
49  
48  
22  
10  
19  
18  
30  
31  
32  
33  
17  
16  
15  
14  
13  
12  
11  
10  
26  
35  
36  
34  
24  
23  
25  
23  
38  
58  
1
39  
56  
55  
5
37  
6
57  
40  
41  
42  
7
8
9
2
3
43  
45  
44  
4
53  
52  
51  
54  
59  
P3457.60  
34106.1 112106  
6
REPLACEMENT PARTS (TCD-1)  
ITEM  
PART NO.  
23820.1000  
22249.0000  
23721.0000  
23819.0000*  
00310.0006  
00459.0001  
01532.0000  
00463.0000  
37689.0000  
32891.0001  
33113.0000  
QTY.  
DESCRIPTION  
1
1
1
1
1
1
1
1
1
1
2
1
Water Strainer Assy (Includes items 2 thru 4)  
2
Cap, Water Strainer  
3
Screen  
4
Housing (Order item 1)  
5
Tube Assy, Strainer to Bulkhead  
Fitting, Bulkhead  
6
7
Lockwasher, Internal Tooth .438"  
Nut, .438" - 20  
8
9
Tube Assy, Bulkhead to Shut-off  
Elbow, Male .25" FLR x .25" MPT  
Valve, Ball .25" FPT x .25" FPT  
10  
11  
12  
32360.0001  
01315.0000  
00970.0000  
2
1
2
Clamp, .613" ID  
Screw, Truss Head #8-32 x .375"  
Nut, Keps #8  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
37898.0000  
37742.0001  
00432.0001  
00430.0001  
21993.0001  
00425.1000  
12422.0006  
33027.0000  
37721.0001*  
37721.0000*  
12422.0001  
33027.0001  
37720.0000*  
1
1
1
1
1
1
4
1
1
1
4
1
1
Gauge, Pressure  
Nipple, .25" MPT  
Elbow, .125" NPT Male/Female  
Adapter, .125" NPT Male/Female  
Regulator, Water, Low Flow  
Fitting, .25" FLR Swivel Nut x .25" Barb  
Clamp, Hose .53"/.59"  
Valve, Check .25" Barb  
Tube, Silicone .25" ID x 6.0" (Order item 66)  
Tube, Silicone .25" ID x 3.5" (Order item 66)  
Clamp, Hose .59"/.66"  
Valve, Check .375" Barb  
Tube, Silicone .375" ID x 3.0" (Order item 67)  
37736.1000  
37736.1001  
38044.0000  
1
1
2
Venturi Assy (.25" product delivery tubing)(Includes item 27-29, 31-33 & 36)  
Venturi Assy (.375" product delivery tubing)(Includes item 27 thru 33 & 36)  
Screw, Plastite #6 x .375"  
NOTE: Effective August 2006, the Venturi and product delivery tubing was changed from .25"ID to .375"ID to improve  
flow rate. If for first replacement, order Tube Replacement Kit P/N 39169.0000 (2 kits required for TCD-2)  
(continued)  
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.  
34106.1 112106  
7
TCD-1  
TCD-2  
REPLACEMENT PARTS (TCD-1)  
(continued)  
60  
61  
63  
62  
61  
47  
.375" BIB Adapter  
Concentrate Bottle Tube  
23  
46  
27  
28  
29  
50  
21  
51  
20  
49  
48  
22  
10  
19  
18  
30  
31  
32  
33  
17  
16  
15  
14  
13  
12  
11  
10  
26  
35  
36  
34  
24  
23  
25  
23  
38  
58  
1
39  
56  
55  
5
37  
6
57  
40  
41  
42  
7
8
9
2
3
43  
45  
44  
4
53  
52  
51  
54  
59  
P3457.60  
34106.1 112106  
8
REPLACEMENT PARTS (TCD-1)  
ITEM  
PART NO.  
QTY.  
DESCRIPTION  
27  
37786.0001  
01360.0002  
2
2
Plate, Fitting Retainer  
Screw, Plascrew #6 x .375"  
28  
29  
30  
31  
32  
33  
34  
35  
32631.0000  
32849.0001  
32631.0001  
37487.1000  
37691.0000  
37486.0000  
32852.0000  
1
2
1
1
1
1
1
Fitting, Barb .25"  
O-ring  
Fitting, Barb .375"  
Venturi Mixer (Includes item 36)  
O-ring  
Adjustment Screw, Venturi  
O-ring  
03093.0001  
01268.0000  
1
1
Wing Nut, Faucet  
Chrome Nut, Faucet Union (Optional)  
36  
37  
01221.0001  
03260.0004  
1
1
C-Ring, Faucet Shank  
Faucet Assy, Black Plastic Body (Includes items 38 thru 44)(Refer to page 18 for  
important ordering information)(See item 70)  
03260.0005  
29163.0007  
29165.0002  
00601.0001  
37715.0000  
29164.0000  
00600.0001  
1
1
1
1
1
1
1
Faucet Assy, Chrome Body (Includes items 38 thru 45)(See item 70)  
38  
39  
40  
41  
42  
43  
44  
Handle, Faucet  
Bonnet, Faucet  
Spring Faucet  
Collar, Spring (Refer to item 69)  
Stem, Faucet  
Seat Cup, Faucet (Refer to item 69)  
35758.0002*  
35206.0000*  
1
1
Faucet Body, Black Plastic (Order item 37)  
Faucet Body, Chrome (Order item 37)  
45  
46  
38473.0000  
1
Insert  
- - - - - - - -  
37720.0003*  
1
1
Tube, Silicone .25" ID x 36.0" (For first replacement, order item 72)  
Tube, Silicone .375" ID x 36.0" (Order item 67)  
47  
48  
49  
50  
51  
52  
53  
34093.0000  
01592.0000  
03043.0006  
38130.0000  
38278.0002*  
38029.1000  
03229.0000  
1
2
1
1
2
1
1
Lid, Reservoir  
Bushing, 1.0" Dia  
Decal, Iced Tea (See page 18 for proper placement)  
Decal, Faucet Under Pressure  
Edging 36.0" (Order item 71)  
Drip Tray Assy (Includes items 53 & 54)  
Drip Tray Cover  
(continued)  
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.  
9
34106.1 112106  
TCD-1  
TCD-2  
REPLACEMENT PARTS (TCD-1)  
(continued)  
60  
61  
63  
62  
61  
47  
.375" BIB Adapter  
Concentrate Bottle Tube  
23  
46  
27  
28  
29  
50  
21  
51  
20  
49  
48  
22  
10  
19  
18  
30  
31  
32  
33  
17  
16  
15  
14  
13  
12  
11  
10  
26  
35  
36  
34  
24  
23  
25  
23  
38  
58  
1
39  
56  
55  
5
37  
6
57  
40  
41  
42  
7
8
9
2
3
43  
45  
44  
4
53  
52  
51  
54  
59  
P3457.60  
34106.1 112106  
10  
REPLACEMENT PARTS (TCD-1)  
ITEM  
54  
PART NO.  
03207.0004  
38465.0000  
38466.0000  
00651.0000  
00656.0000  
38839.0000  
QTY.  
DESCRIPTION  
1
1
1
1
1
1
Drip Tray  
55  
Decal, Pressure Regulator  
Decal, Shut-off  
56  
57  
Decal, BUNN  
58  
Decal, Plumbing Code  
Stand (Optional)  
59  
60  
26443.0000  
34644.0000  
1
1
Reducer, Barb .375" x .25"  
Connector, Barb .375" x .375"  
61  
62  
12422.0001  
2
Clamp, Hose .59"/.66"  
For use with .375" BIB adapter  
37720.0000*  
38295.0000*  
1
1
Tube, Silicone .375" ID x 3.0" (Order item 67)  
Tube, Silicone .375" ID x 36.0" (Order item 67)  
63  
37744.0000  
37744.0001  
1
1
Tube, Concentrate Bottle .25"  
Tube, Concentrate Bottle .375"  
Optional  
64  
65  
66  
00674.0000  
M2531.0000  
1
1
Brush, Tube .75" (Not illustrated)  
Lube&Sealant Compound (Not illustrated)  
37721.1000  
37721.1001  
37721.1002  
-
-
-
Tube, Silicone .25" ID x 12.0"  
Tube, Silicone .25" ID x 36.0"  
Tube, Silicone .25" ID x 120.0"  
67  
68  
37720.1000  
37720.1001  
37720.1002  
-
-
-
Tube, Silicone .375" ID x 12.0"  
Tube, Silicone .375" ID x 36.0"  
Tube, Silicone .375" ID x 120.0"  
37747.1000  
37747.1001  
-
-
Parts Bag (Includes items 1,5,23,37,49 & 63)(with 3.0" BIB hose)  
Parts Bag (Includes items 1,5,23,37,52,62 & 63)(with 36.0" BIB hose)  
69  
70  
71  
72  
38471.0000  
28707.0004  
38278.1002  
39169.0000  
-
-
-
-
Kit, Faucet Seat Cup (Includes items 41 & 43)  
Kit, Faucet Repair (Includes items 38 & 40-43)  
Edging 36.0" (Use as required)  
Tube Replacement Kit (Includes items 23,24,25,30 & 46)  
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.  
11  
34106.1 082506  
TCD-1  
TCD-2  
REPLACEMENT PARTS (TCD-2)  
65  
66  
53  
50  
51  
52  
51  
Concentrate Bottle Tube  
54  
.375" BIB Adapter  
51  
49  
Bag Divider  
30  
59  
63  
31  
33  
24  
22  
10  
18  
32  
34  
35  
36  
19  
20  
17  
26  
21  
16  
15  
25  
23  
19  
37  
39  
29  
38  
14  
13  
12  
11  
10  
27  
58  
41  
42  
1
5
40  
51  
28  
6
43  
44  
61  
62  
7
60  
8
9
45  
46  
48  
47  
2
3
4
56  
57  
55  
64  
63  
P3462.60  
34106.1 112106  
12  
REPLACEMENT PARTS (TCD-2)  
DESCRIPTION  
ITEM  
PART NO.  
23820.1000  
22249.0000  
23721.0000  
23819.0000*  
00310.0006  
00459.0001  
01532.0000  
00463.0000  
37689.0000  
32891.0001  
33113.0000  
QTY.  
1
2
1
1
1
1
1
1
1
1
1
2
1
Water Strainer Assy (Includes items 2 thru 4)  
Cap, Water Strainer  
3
Screen  
4
Housing (Order item 1)  
Tube Assy, Strainer to Bulkhead  
Fitting, Bulkhead  
5
6
7
Lockwasher, Internal Tooth .438"  
Nut, .438" - 20  
8
9
Tube Assy, Bulkhead to Shut-off  
Elbow, Male .25" FLR x .25" MPT  
Valve, Ball .25" FPT x .25" FPT  
10  
11  
12  
32360.0001  
01315.0000  
00970.0000  
3
1
3
Clamp, .613" ID  
Screw, Truss Head #8-32 x .375"  
Nut, Keps #8  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
37898.0000  
37742.0001  
00432.0001  
00430.0001  
21993.0001  
00425.1000  
12422.0000  
37721.0004*  
38023.0000  
01592.0000  
37721.0006*  
03043.0006  
12422.0006  
33027.0000  
33027.0001  
1
1
1
1
1
1
3
2
1
4
2
1
5
1
2
Gauge, Pressure  
Nipple, .25" MPT  
Elbow, .125" NPT Male/Female  
Adapter, .125" NPT Male/Female  
Regulator, Water, Low Flow  
Fitting, .25" FLR Swivel Nut x .25" Barb  
Clamp, Hose .47"/.54"  
Tube, Silicone .25" ID x 2.0" (Order item 69)  
Y-Fitting, Barb .25" Hose  
Bushing, 1.0" Dia  
Tube, Silicone .25" ID x 4.75" (Order item 69)  
Decal, Iced Tea (See page 18 for proper placement)  
Clamp, Hose .53"/.59"  
Valve, Check .25"  
Valve, Check .375"  
- - - - - - - -  
37720.0000*  
2
2
Tube, Silicone .25" ID x 3.5" (If for first replacement, order item 75)  
Tube, Silicone .375" ID x 3.0" (Order item 70)  
29  
37736.1000  
37736.1001  
01360.0002  
2
2
4
Venturi Assy (.25" product delivery tubing)(Each includes items 30,31, 33-36 & 39)  
Venturi Assy (.375" product delivery tubing)(Each includes items 30 thru 36 & 39)  
Screw, Plascrew #6 x .375"  
NOTE: Effective August 2006, the Venturi and product delivery tubing was changed from .25"ID to .375"ID to improve  
flow rate. If for first replacement, order Tube Replacement Kit P/N 39169.0000 (2 kits required for TCD-2)  
(continued)  
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.  
13  
34106.1 112106  
TCD-1  
TCD-2  
REPLACEMENT PARTS (TCD-2)  
(continued)  
65  
66  
53  
50  
51  
52  
51  
Concentrate Bottle Tube  
54  
.375" BIB Adapter  
51  
49  
Bag Divider  
30  
59  
63  
31  
33  
24  
22  
10  
18  
32  
34  
35  
36  
19  
20  
17  
26  
21  
16  
15  
25  
23  
19  
37  
39  
29  
38  
14  
13  
12  
11  
10  
27  
58  
41  
42  
1
5
40  
51  
28  
6
43  
44  
61  
62  
7
60  
8
9
45  
46  
48  
47  
2
3
4
56  
57  
55  
64  
63  
P3462.60  
34106.1 112106  
14  
REPLACEMENT PARTS (TCD-2)  
ITEM  
PART NO.  
QTY.  
DESCRIPTION  
30  
37786.0001  
38044.0000  
2
2
Plate, Fitting Retainer  
Screw, Plastite #6 x .375"  
31  
32  
33  
34  
35  
36  
37  
32631.0000  
32631.0001  
32849.0001  
37487.1000  
37691.0000  
37486.0000  
1
1
2
1
1
1
Fitting, Barb .25"  
Fitting, Barb .375"  
O-ring  
Venturi Mixer (Includes item 39)  
O-ring  
Adjustment Screw, Venturi  
03093.0001  
01268.0000  
2
2
Wing Nut, Faucet  
Chrome Nut, Faucet Union (Optional)  
38  
39  
40  
32852.0000  
01221.0001  
03260.0004  
2
2
2
O-ring  
C-Ring, Faucet Shank  
Faucet Assy, Black Plastic Body (Includes items 41 thru 47)(Refer to page 18 for  
important ordering information)(See item 73)  
Faucet Assy, Chrome Body (Includes items 41 thru 48)(See item 73)  
03260.0005  
29163.0007  
29165.0002  
00601.0001  
37715.0000  
29164.0000  
00600.0001  
2
1
1
1
1
1
1
41  
42  
43  
44  
45  
46  
47  
Handle, Faucet  
Bonnet, Faucet  
Spring Faucet  
Collar, Spring (Refer to item 72)  
Stem, Faucet  
Seat Cup, Faucet (Refer to item 72)  
35758.0002*  
35206.0000*  
1
1
Faucet Body, Black Plastic (Order item 40)  
Faucet Body, Chrome (Order item 40)  
48  
49  
38473.0000  
1
Insert  
- - - - - - - -  
37720.0003*  
2
2
Tube, Silicone .25" ID x 36.0" (If for first replacement, order item 75)  
Tube, Silicone .375" ID x 36.0" (Order item 69)  
50  
26443.0000  
34644.0000  
2
2
Reducer, Barb .375" x .25"  
Connector, Barb .375" x .375"  
For use with .375" BIB adapter  
51  
52  
12422.0001  
12  
Clamp, Hose .59"/.66"  
37720.0000*  
38295.0000*  
2
2
Tube, Silicone .375" ID x 3.0" (Order item 70)  
Tube, Silicone .375" ID x 36.0" (Order item 70)  
53  
37744.0000  
37744.0001  
2
2
Tube, Concentrate Bottle .25"  
Optional  
Tube, Concentrate Bottle .375"  
54  
55  
56  
57  
34093.0000  
38029.1000  
03229.0000  
03207.0004  
1
1
1
1
Lid, Reservoir  
Drip Tray Assy (Includes items 56 & 57)  
Drip Tray Cover  
Drip Tray  
(continued)  
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.  
15  
34106.1 112106  
TCD-1  
TCD-2  
REPLACEMENT PARTS (TCD-2)  
(continued)  
65  
66  
53  
50  
51  
52  
51  
Concentrate Bottle Tube  
54  
.375" BIB Adapter  
51  
49  
Bag Divider  
30  
59  
63  
31  
33  
24  
22  
10  
18  
32  
34  
35  
36  
19  
20  
17  
26  
21  
16  
15  
25  
23  
19  
37  
39  
29  
38  
14  
13  
12  
11  
10  
27  
58  
41  
42  
1
5
40  
51  
28  
6
43  
44  
61  
62  
7
60  
8
9
45  
46  
48  
47  
2
3
4
56  
57  
55  
64  
63  
P3462.60  
34106.1 112106  
16  
REPLACEMENT PARTS (TCD-2)  
ITEM  
PART NO.  
QTY.  
DESCRIPTION  
58  
59  
60  
61  
62  
63  
64  
65  
66  
00656.0000  
38130.0000  
38465.0000  
38466.0000  
00651.0000  
38278.0002*  
38839.0000  
38745.1000  
1
1
1
1
1
2
1
1
Decal, Plumbing Code  
Decal, Faucet Under Pressure  
Decal, Pressure Regulator  
Decal, Shut-off  
Decal, BUNN  
Edging 36.0" (Order item 74)  
Stand  
Bag Divider (Includes Item 66)  
38278.0001*  
38278.0003*  
1
2
Edging 9.5" (Order item 74)  
Edging 1.0" (Order item 74)  
67  
68  
69  
00674.0000  
M2531.0000  
1
1
Brush, Tube .75" (Not illustrated)  
Lube&Sealant Compound (Not illustrated)  
37721.1000  
37721.1001  
37721.1002  
-
-
-
Tube, Silicone .25" ID x 12.0"  
Tube, Silicone .25" ID x 36.0"  
Tube, Silicone .25" ID x 120.0"  
70  
71  
37720.1000  
37720.1001  
37720.1002  
-
-
-
Tube, Silicone .375" ID x 12.0"  
Tube, Silicone .375" ID x 36.0"  
Tube, Silicone .375" ID x 120.0"  
37747.1002  
37747.1003  
-
-
Parts Bag (Includes items 1,5,24,40,51 & 53)(with 3.0" BIB hose)  
Parts Bag (Includes items 1,5,40,50,51,52,53 & 55)(with 36.0" BIB hose)  
72  
73  
74  
75  
38471.0000  
28707.0004  
38278.1002  
39169.0000  
-
-
-
-
Kit, Faucet Seat Cup (Includes items 44 & 46)  
Kit, Faucet Repair (Includes items 41 & 43-46)  
Edging 36.0" (Use as required)  
Tube Replacement Kit (Includes items 27,32,49,51-53)(Two Kits required for TCD-2)  
* Indicates the part number listed is for reference only. See DESCRIPTION for possible service replacement.  
17  
34106.1 082506  
ICED TEA DECAL PLACEMENT  
APPROX.  
5“  
PLASTIC BODY FAUCET COMPARISON  
If you have a plastic body faucet of this  
design, you must order a complete new  
plastic faucet.  
New Plastic Faucet Design  
34106.1 020306  
18  

Blaupunkt CANBERRA RCM 85 User Manual
Canon UC9500 User Manual
Dual XR4115 User Manual
Earthquake Sound DBXI 10D User Manual
Hitachi DZ HS503 User Manual
Hitachi VM E520A User Manual
Hobie 38040011 User Manual
JL Audio 12WX 4 User Manual
JVC Car Video System KD AVX44J User Manual
JVC GR AXM341 User Manual