Breville BBL500 User Manual

Wizz Electronic  
Combined blender and food processor  
Instructions for use  
Includes recipes  
Model BBL500  
Breville recommends safety first  
We at Breville are very safety conscious. We design and manufacture consumer products with the safety of you,  
our valued customer foremost in mind.  
Important safeguards for all electrical appliances  
In addition, we ask that you exercise a degree of care when using any electrical appliance and adhere to the  
following precautions:  
Fully unwind the cord before use.  
This appliance is for household use only. Do not use  
this appliance for anything other than its intended  
use. Do not use in moving vehicles or boats. Do not  
use outdoors.  
To protect against electric shock, do not immerse  
cord, plug or motor base in water or any  
other liquid.  
Read all instructions before operating and save for  
future reference  
The installation of a residual current device  
(safety switch) is recommended to provide  
additional safety protection when using electrical  
appliances. It is advisable that a safety switch with  
a rated residual operating current not exceeding  
30mA be installed in the electrical circuit supplying  
the appliance. See your electrician for  
Do not let the cord hand over the edge of a table  
or counter, touch hot surfaces or become knotted.  
Important safeguards for all electrical appliances  
Remove any packaging material and promotional  
stickers before using the Breville Wizz Electronic for  
the first time.  
when the Breville Wizz Electronic is not in use and  
before cleaning and storing.  
This appliance is not intended for use by young  
children or infirm persons without supervision.  
Do not operate the appliance continuously with  
heavy loads for more than 1 minute. None of the  
recipes in this instruction book are considered a  
heavy load.  
Young children should be supervised to ensure that  
they do not play with the appliance.  
Do not place the Breville Wizz Electronic near the  
edge of a bench or table during operation. Ensure  
that surface is level, clean and free of water, flour  
etc. Vibration during operation may cause the  
appliance to move.  
It is recommended to regularly inspect the  
appliance. Do not use the appliance if the power  
supply cord, plug or appliance becomes damaged in  
any way. Return the entire appliance to the nearest  
authorised Breville Service Centre for examination  
and/or repair.  
professional advice.  
Be careful when handling the Breville Wizz  
Electronic processing and blending blades and  
processing disc as they are very sharp. Mis-handling  
of the blades or disc may cause injury.  
Do not place this appliance on or near a hot gas  
or electric burner, or where it could touch a  
heated oven.  
Never place your fingers inside the blender jug or  
food processor bowl during operation.  
Any maintenance other than cleaning should be  
performed at an authorised Breville Service Centre.  
Always ensure the Breville Wizz Electronic is  
properly assembled before use. Follow the  
instructions provided in this book.  
Keep hands, hair, clothing, as well as spatulas and  
other utensils away from the blender jug or food  
processor bowl during operation.  
Use only the blender jug, food processor bowl and  
parts supplied with the Breville Wizz Electronic.  
Do not remove blender jug or food processor bowl  
from the motor base whilst in operation.  
Always assemble the blade assembly into the  
blender jug, before attaching to motor base. Never  
place blade assembly on motor base without the  
blender jug attached.  
To protect against electric shock do not immerse  
the motor base, plug or cord in water or any  
other liquid.  
Do not use the Breville Wizz Electronic for anything  
other than food and/or beverage preparation.  
Always ensure the blender lid is firmly positioned  
on the blender jug or that the food processor lid is  
locked into position on the food processor bowl  
before operating.  
Do not process boiling liquids, allow to cool before  
placing into the blender jug or food processor bowl.  
Make sure the motor and blade have completely  
stopped, the control panel buttons are switched off  
by pressing the Stop button, the appliance is  
switched off at the power outlet and unplugged  
from the power outlet the before disassembling.  
Do not leave the Breville Wizz Electronic unattended  
when in use.  
Ensure control panel buttons are switched off by  
pressing the ‘Stop’ button, switch the appliance off  
at the power outlet and unplug from the power  
outlet before attaching the blender or food  
DO NOT OPERATE THE BREVILLE WIZZ ELECTRONIC CONTINUOUSLY ON HEAVY LOADS FOR  
MORE THAN 60 SECONDS.  
Keep the appliance clean. Follow the cleaning  
instructions provided in this book.  
processor or attempting to move the appliance, or  
4
5
Know your Breville Wizz Electronic  
Operating your Breville Wizz Electronic  
Blender Blade Assembly Tool  
Before first use  
Step 2.  
Before using your Breville Wizz Electronic for the  
first time, remove any packaging material and  
promotional labels. Ensure the appliance is  
switched off at the power outlet and the power  
cord is unplugged.  
Turn the glass blender jug upside down with the  
white plastic surround facing upward. Insert the  
silicon seal onto the round glass base of the blender  
jug. Carefully insert the blender blade assembly into  
the round glass base of the blender jug, aligning the  
white tabs of the blade assembly in between the  
white tabs of the white plastic surround. Use the  
Blade Assembly Tool to press the blade assembly  
down and turn clockwise to lock into position.  
Reversible Stainless Steel slicing/shredding disc  
Blender lid  
slicing side perfect for slicing vegetables and  
fruits; shredding side ideal for shredding firm  
cheeses, fruit and vegetables.  
locks firmly onto the blender jug for safety  
Removable centrally located  
inner lid (50ml capacity)  
Wash all parts (except motor base and food processor  
bowl support) of the Breville Wizz Electronic in warm,  
soapy water with a soft cloth. Rinse and dry  
add liquids or other ingredients  
through the lid opening while  
the blender is operating.  
Food Processor Bowl with handle  
400 mls liquid, 2 cups of food  
thoroughly. Do not place parts in the dishwasher.  
2
When first using your Breville Wizz Electronic  
Combined Blender and Processor, you may  
notice an odour coming from the motor. This is  
normal and will dissipate with use.  
Blade  
Assembly  
Tool  
Processor Bowl safety locking lid  
1.5 litre Blender  
glass jug  
Food Pusher  
guides food down the feed chute.  
Note  
Stainless Steel  
chopping blade  
Step 3.  
Assembling and Attaching the Blender  
perfect for all  
Turn the glass blender jug upright and insert onto  
motor base, aligning the jug handle with the 'align  
handle' graphic on the motor base. Add food or liquid  
into the blender jug. Place the blender lid firmly into  
position on the top of the blender jug and turn  
anticlockwise to lock into position. Insert the inner lid  
into the blender lid.  
Advanced stainless  
chopping, mixing and  
processing tasks  
1
steel blade assembly  
removable for easy cleaning  
Powerful 700 watt motor  
3
Push button 5 speed  
function control panel  
plus pulse and  
ice crush  
Food Processor  
Bowl support  
Step 1.  
Place the motor base on a flat, dry surface such  
as a bench top. Ensure that the motor base is  
switched OFF at the power outlet and the power  
cord is unplugged.  
Cord Storage  
Non skid feet  
Disc shaft  
locks onto motor spindle  
THE WHITE PLASTIC SURROUND ON THE BASE OF THE BLENDER JUG CANNOT BE REMOVED  
6
7
Operating your Breville Wizz Electronic  
continued  
Step 4.  
Step 7.  
Assembling and Attaching the Food  
Processor Bowl with the chopping blade  
Step 3.  
Plug the power cord into a 230/240v power outlet  
and switch on. The red light beside the Stop button  
will illuminate and remain illuminated whilst the  
appliance is switched on at the power outlet.  
The Ice Crush button has the highest speed and  
operates independent of the Pulse function. Press the  
Ice Crush button in short bursts to operate.  
Attach the processing bowl lid by positioning the feed  
chute opposite to the handle then turning the lid  
anticlockwise until it locks into position.  
Step 1.  
Place the motor base on a flat, dry surface such  
as bench top. Ensure that the motor base is  
switched ‘OFF’ at the power outlet and the power  
cord is unplugged.  
Step 8.  
3
4
At the end of use, switch off at the power outlet and  
remove the power cord.  
Important: to crush ice  
1
Place 1 cup of frozen ice cubes into the Blender Jug.  
Replace lid and push the button in to PULSE for short  
bursts until a snowy textured ice is achieved. This will  
take approximately 15 seconds.  
During the blending process, ingredients may  
stick to the sides of the either the Blender jug  
or Food Processor bowl. To push the food back  
onto the blades, press the Stop button and  
switch off at the power outlet. Remove the lid  
and use a plastic spatula to scrape down the  
sides of the jug. Replace the lid before  
Step 5.  
Step 4.  
Select the required speed function by pressing in the  
corresponding speed button for example Low Speed 1  
up to High Speed 5. A red light will illuminate beside  
the speed button as it is selected. Speed can be  
changed at any time during the blending process.  
Press Stop button, located at the front of the motor  
base, to finish blending.  
To commence processing ensure the food pusher is  
positioning in the feed chute. Plug the power cord  
into a 230/240V power outlet and switch on.  
Select a function by pressing in the corresponding  
function button on the control panel and its light  
will illuminate.  
Step 2.  
Insert the food processor bowl support onto the  
motor base. Place the food processor bowl onto the  
spindle of the food processor bowl support and  
recommending blending or processing.  
Note  
turn anti-clockwise until locked into position. Ensure  
the handle on the food processor aligns with the  
'align handle' graphic on the motor base. Insert the  
chopping blade over the shaft, and rotate into  
position. Add food or liquid into the food processor  
bowl. Do not overfill the food processor bowl.  
4
Step 6.  
If any moisture of liquid appears on top of the  
motor base, press the Stop button, switch off at  
the power outlet and remove the power plug.  
Remove the blender jug or food processing  
bowl. Wipe the motor base immediately with  
paper towelling and check the blender jug or  
food processing bowl are correctly assembled.  
For ingredients that require short bursts of power, use  
the Pulse function. Press the Pulse button and the red  
light beside it will flash then select a speed button  
and press in short bursts until blending is complete.  
When a speed button is selected, the red lights  
beside the Pulse and Speed buttons will remain  
illuminated whilst the speed button is pressed in.  
2
Note  
NEVER PLACE ANYTHING OTHER THAN FOOD AND LIQUIDS IN THE WIZZ ELECTRONIC WHILST  
THE MOTOR IS RUNNING.  
DO NOT OPERATE THE WIZZ ELECTRONIC CONTINUOUSLY ON HEAVY LOADS FOR MORE THAN  
ONE MINUTE.  
8
9
Operating your Breville Wizz Electronic  
continued  
Step 5.  
Step 7.  
Assembling and Attaching the Food  
Processor Bowl with the reversible  
slicing\shredding disc  
Step 3.  
The food pusher can be removed throughout the  
processing to add liquids or other foods.  
At the end of use, switch off at the power outlet and  
remove the power cord.  
Insert the disc shaft over the motor spindle. Place the  
disc onto the disc shaft, with required function facing  
upwards, for example, for slicing have slicing side  
facing upwards. Align the disc centre onto the shaft,  
rotate and push down, until it locks into position.  
Attach the processor bowl lid by positioning the feed  
chute opposite to the handle then turning the lid  
anticlockwise until it locks into position.  
Step 1.  
5
Place the motor base on a flat, dry surface such as  
bench top. Ensure that the motor base is switched off  
at the power outlet and the power cord is unplugged.  
1
3
Step 6.  
To switch off, press the same button again or press  
the Stop button in the middle of the speed  
control panel.  
Step 2.  
Insert the food processor bowl support onto the motor  
base, aligning the arrow on the support with the arrow  
on the motor base. Place the Food Processor Bowl onto  
the motor spindle of the food processor bowl support,  
and turn anti-clockwise until locked into position.  
Step 4.  
To commence processing ensure the food pusher is  
positioning in the feed chute. Plug the power cord  
into a 230/240V power outlet and switch on.  
Select a function by pressing in the corresponding  
function button on the control panel and its light  
will illuminate.  
6
2
DO NOT OPERATE THE BREVILLE WIZZ ELECTRONIC CONTINUOUSLY ON HEAVY LOADS FOR  
MORE THAN 1 MINUTE.  
DO NOT USE THE BREVILLE WIZZ ELECTRONIC FOR ANYTHING OTHER THAN FOOD AND OR  
BEVERAGE OPERATION.  
10  
11  
Operating your Breville Wizz Electronic  
continued  
Care and cleaning  
Always ensure the Breville Wizz Electronic is in the  
off position, by pressing Stop on the  
speed/function control panel and switching off at  
the power outlet and unplugging the power cord.  
Step 6.  
4
Note: do not use abrasive souring pads or  
cleaners when cleaning the parts or motor base  
as they may scratch the surface.  
To switch off, press the same button again or press  
the Stop button in the middle of the speed control  
panel.  
To remove the blender jug from the motor base,  
grasp the handle and lift upwards. Use the Blender  
Blade Assembly Tool to remove the Blender Blade  
Assembly. The white plastic surround on the base of  
the blender jug cannot be removed.  
Note  
6
Removing stubborn or strong food stains  
and odours  
To remove the food processor bowl from the food  
processor support on the motor base, turn bowl  
clockwise and lift upwards. Follow instructions in  
‘Assembly and Operation of your Breville Wizz  
Electronic’ on page 9.  
Strong smelling foods such as garlic, fish and some  
vegetables such as carrots may leave an odour or  
stain on the processor bowl, lid and disc holder,  
blender jug and lid. To remove, soak processing bowl,  
lid and disc holder or blender jug and lid for 5  
minutes in 100mls bleach dissolved in 2 litres water.  
Then wash with a mild detergent and warm water,  
rinse well and dry thoroughly.  
Step 5.  
Remove the food pusher, insert the food to be sliced  
or shredded and push down with the food pusher to  
guide the food through the chute. Repeat with  
remaining food. Do not overfill the food  
processor bowl.  
Cleaning the Motor Base, Food Processor  
Bowl Support and Blender Blade  
Assembly Tool  
Step 7.  
Wipe the motor base, food processor bowl support  
and blender blade assembly tool with a soft, damp  
cloth then dry thoroughly.  
Storage  
At the end of use, switch off at the power outlet and  
remove the power cord.  
Store Breville Wizz Electronic on the kitchen bench  
top. The slicing/shredding disc can be stored in the  
food processor bowl, with the lid and food pusher in  
position. The blender jug, blade assembly and lids  
can be assembled and stored next to it. Place the  
food processor blade and blender blade assembly tool  
in the blender jug for safe storage.  
Wipe any excess food particles from the  
power cord.  
Cleaning the Food Processor Bowl, Lid,  
Blade, Disc, Disc Shaft and Food Pusher,  
Blender Jug, Blade Assembly, Inner Lid  
and Lid  
Wash all parts in warm soapy water with a soft  
cloth. Use a kitchen bottle brush to dislodge foods  
from the disc shaft, processing blade and disc.  
Rinse and dry thoroughly.  
THE CHOPPING BLADE AND DISCS ARE EXTREMELY SHARP!! USE CAUTION WHEN HANDLING  
AND STORING THESE PARTS. ALWAYS STORE THE CHOPPING BLADE WITH THE PROTECTIVE  
COVER PROVIDED  
BE CAREFUL WHEN HANDLING THE CUTTING BLADES AS THEY ARE SHARP. MISHANDLING OF  
THE BLADES MAY CAUSE INJURY.  
12  
13  
Tips on how to best use your Breville Wizz Electronic  
Suggested uses for your Breville Wizz Electronic  
When blending thick or dry mixtures it may be  
Do  
Don’t  
Crush ice  
necessary to stop the Breville Wizz Electronic and  
Place 1 cup of frozen ice cubes into Blender jug  
scrape down the sides of the blender jug and or  
only and blend using the ‘ice crush’ speed control  
food processor bowl with a plastic or rubber  
Use Low speeds (1-3) for emulsions such as  
mayonnaise, dressings, marinades and foods that  
require mixing until just combined, such as batters.  
Do not operate a heavy mixture for more than 1  
minute. For normal blending tasks, for example,  
mayonnaise, dressings etc, do not operate for  
longer than 1 minute at one time without turning  
off the Breville Wizz Electronic and stirring the  
ingredients, and then continue blending.  
until crushed.  
spatula, once or twice during blending or  
processing.  
Use High speeds (4-5 and Ice Crushing) for  
pureeing, drink or cocktail making.  
Drinks  
Cut all food pieces into 2 cm cubes where  
appropriate.  
1
4
Fill the container to at least ⁄ full, remember to  
leave room to allow froth to form as the drink  
is aerated.  
Use PULSE for foods that only require short bursts  
of power such chopping nuts.  
Do not operate Breville Wizz Electronic without  
having the blender lids or food processing lid in  
position. To add additional ingredients whilst  
blending remove inner lid and place ingredients  
through the opening in the middle of the lid. If  
having to add additional ingredients to the food  
processor while blending, the food pusher can be  
removed and additional ingredients can be added  
through the feed chute.  
Ensure all parts have been thoroughly washed,  
rinsed and dried before assembly.  
Soups, sauces, purees  
Ensure the Breville Wizz Electronic is correctly  
assembled before operating (see page 9).  
The most efficient amount to blend will depend on  
the food/recipe used. Generally, the more liquid  
used, the more can be processed at one time. Do not  
place hot ingredients into the Breville Wizz Electronic,  
allow to cool before pureeing.  
Ensure the base of the blender jug is thoroughly  
dry before placing onto the motor base.  
Ensure the food processor support and base of the  
food processor bowl are thoroughly dry before  
placing onto the motor base.  
Do not place any objects, other than food, into the  
Breville Wizz Electronic whilst the motor is running.  
Batters  
Ensure the Breville Wizz Electronic is placed on a  
clean, dry and level surface to operate.  
Place liquid ingredients, then dry ingredients, into  
either the blender jug or food processor bowl. Blend  
until a smooth batter is formed.  
Do not use either blender jug or food processor  
bowl to store food.  
Ensure liquids ingredients are placed into Breville  
Wizz Electronic before solid ingredients, except  
where specified in recipes.  
As air does not circulate when blending, therefore  
the Breville Wizz Electronic will not beat egg  
whites, knead dough or mash potatoes.  
Quantities and Handy Hints  
Do not put more than 2 cups of warm ingredients  
into the Breville Wizz Electronic before blending or  
processing starts. After the blending process has  
Ensure all foods are cut into cubes (approx. 2-3cm  
squares) where appropriate to achieve an even  
result.  
Do not remove either blender jug or food processor  
bowl while the Breville Wizz Electronic is operating.  
Always make sure the control panel is on the ‘Stop’  
position, switch off the power at the power outlet  
and unplug the power cord from the power outlet.  
begun and the blades are turning you may slowly  
Use a plastic or rubber spatula to dislodge food  
from sides of jug or bowl. Always ensure that the  
Breville Wizz Electronic is turned off by pressing the  
“Stop” button on the control panel and that the  
power has been switched off at power outlet and  
the power plug removed. Ensure blades have  
stopped rotating. Do not use metal utensils as they  
may damage the blades, jug or bowl.  
1
2
add another 1 ⁄ cups of ingredients through the  
opening in the lid if desired.  
Do not overload the Breville Wizz Electronic with  
more than the specified quantity of ingredients as  
doing so could cause the motor to stall. Turn the  
Breville Wizz Electronic off by pressing the ‘Stop’  
button on the control panel, switch off the power  
at the power outlet and unplug cord. Remove a  
portion of the mixture before continuing.  
Thick mixtures puree more efficiently if the Breville  
1
1
4
2
Wizz Electronic is ⁄ to ⁄ full.  
When using several ingredients, place liquid  
ingredients in the blender jug or food processor  
bowl first unless specified in the recipe.  
Do not place hot ingredients into the Breville Wizz  
Electronic, allow to cool before placing into the  
blender jug or food processor bowl.  
14  
15  
Recommended foods, quantities and function  
Type of  
food/drink  
Preparation  
Maximum  
amount at  
one time  
Function - mix  
puree etc  
Approximate  
time  
Trouble Shooting Chart  
Problem  
Solution  
Lean meat  
Fish  
Trim excess fat  
and sinew  
300g  
300g  
300g  
5 cloves  
50g  
Chop Food  
Processor (button 2)  
10-20 seconds  
10-20 seconds  
10-15 seconds  
10-15 seconds  
10-15 seconds  
5 seconds  
Motor doesn’t start or blade doesn’t rotate  
• Check that the blender jug or processing bowl and lid  
are securely locked into position.  
• Check the Stop ready light is illuminated.  
• Check that the power plug is securely inserted into  
the power outlet and switched ON  
Remove skin and bones  
and cut into 2cm cubes  
Chop Food  
Processor (button 2)  
Onions, whole  
Garlic, clove  
Apple, raw  
Peel and cut into  
1.5-2cm pieceS  
Chop Food  
Processor (button 2)  
• Be sure to press only one function control button  
at a time  
Peel  
Chop Food  
Processor (button 2)  
Food is unevenly chopped  
Either too much food is being chopped at one time or  
the pieces are not small enough. Try cutting food into  
smaller pieces of even size and processing a smaller  
amount per batch. For best results the food should be  
chopped into pieces no larger than 2cm  
Peel, cored and cut  
into 1.5cm pieces  
Chop Food  
Processor (button 2)  
Cabbage, green  
or red  
Remove the core and  
cut into 2 cm cubes  
50g  
Chop Food  
Processor (button 2)  
Food is chopped too fine or is watery  
The food is over processed. Use brief pulses or process  
for a shorter time.  
Peanuts, whole,  
shells removed  
Remove the skin  
200g  
100g  
125g  
Grind Food  
Processor (button 5)  
15 seconds  
Food collects on processing bowl cover or side of bowl  
Processing too much food. Turn the Food processor off.  
When the blade stops rotating, remove the cover and  
clean the bowl and cover with a spatula. Reduce  
quantity of food to be processed  
Bread or  
biscuit crumbs  
Cut bread into 2 cm pieces  
and break up biscuits  
Chop Food  
Processor (button 2)  
15 seconds  
Food sticks to blade  
Processing too much food. Turn the Food processor off.  
When the blade stops rotating, remove the cover.  
Carefully remove the blade. Remove the food from the  
blade with a spatula, reduce quantity of food and  
continue processing.  
Mayonnaise  
Mix the egg yolk  
and vinegar. Then add the oil  
Mix Blender (Speed 1)  
and Food Processor  
(button 1)  
60 seconds  
Whipped cream  
Add sugar or vanilla  
if desired  
200ml  
Mix Blender (Speed 1)  
and Food Processor  
(button 1)  
60 seconds  
Food Processor Bowl Capacity  
Peppercorns  
Whole  
Halve  
100g  
30g  
Grind Food Processor  
(button 5)  
20-30 seconds  
20-30 seconds  
20-30 seconds  
20-30 seconds  
Item  
Capacity  
300g  
Cinnamon sticks  
Fresh ginger  
Grind Food Processor  
(button 5)  
Onion  
Meat  
Peel, cut into  
1.5cm pieces  
100g  
300g  
Chop Food Processor  
(button 2)  
300g  
Cheese  
Fish  
200g  
Carrots,  
zucchini,  
eggplant  
Arrange foods vertically in the  
feed chute, cutting them so  
they are even in height.  
Slicing disc Food  
(button 3)  
300g  
Pumpkin  
Eggs  
300g  
For slices arrange foods  
horizontally in the feed chute.  
Process by exerting form  
pressure on the food pusher.  
4 x 60g eggs  
300g  
Prawns  
Mushrooms  
Cheese  
Wipe the mushrooms and  
pack in the feed chute on  
their sides. Process using light  
pressure on the food pusher  
200g  
120g  
Slicing disc Food  
Processor (button 3)  
20-30 seconds  
20- 30 seconds  
Cut the cheese into piece large  
enough to just fit the feed chute.  
Process using light pressure on  
the food pusher to prevent  
cheese crumbling  
Slicing\shredding disc  
Food Processor  
(button 3)  
16  
17  
Notes  
Breville Customer Service Centre  
Australian Customers  
New Zealand Customers  
Breville Customer Service Centre  
Breville Customer Service Centre  
Locked Bag 2000  
Botany NSW 2019  
AUSTRALIA  
Private Bag 94411  
Greenmount  
Auckland, New Zealand  
Customer Service: 09 271 3980  
0800 288 513  
Customer Service: 1300 139 798  
(02) 9384 9601  
Fax  
Fax  
Email Customer Service: [email protected] Email Customer Service: [email protected]  
Breville is a registered trademark of Breville Pty. Ltd. ABN 98 000 092 928  
© Copyright. Breville Pty. Ltd. 2004  
Wizz Electronic is a trademark of Breville Pty. Ltd.  
Due to continual improvements in design or otherwise, the product you  
purchase may differ slightly from the one illustrated in this booklet.  
Model BBL500 Issue 1/05  
19  
Recipes  
Delicious recipes  
Includes instructions for use  
Contents  
Dips and starters  
Guacamole  
Pesto dip  
1 large avocado, peeled, de-stoned  
and chopped  
1 cup fresh basil leaves  
1 clove garlic peeled and chopped  
40 ml lemon juice  
40 ml lemon juice  
1
2
⁄ cup sour cream  
60g pine nuts  
1
4
1 teaspoons minced garlic  
1 teaspoon chilli  
⁄ cup olive oil  
1
2
⁄ cup cottage cheese  
60g grated fresh Parmesan cheese  
1. Place avocado, lemon juice, sour cream, garlic and  
chilli sauce in blender jug.  
1. Place basil leaves, garlic, lemon juice and pine  
nuts in blender, using high speed, blend until  
finely chopped.  
2. Use speed 2 and blend until smooth.  
Serve with crustini or crudités  
Page  
R3  
Dips and starters  
Soups  
2. With motor running, pour in oil and blend until  
smooth. Add cheeses and mix to combine.  
This recipe can be made in the food processor  
using the chopping blade  
R4  
3. Chill until ready to use.  
Pancakes  
R5  
Note  
Serve with toasted Turkish bread.  
Cocktails  
R6  
This recipe can be made in the food processor  
using the chopping blade  
Non-alcoholic drinks  
Smoothies and milkshakes  
Recipes for use with Food Processor  
Sauces and Dressings  
Main Meals  
R7  
R8  
Note  
R9  
R10  
R11  
R12  
R14  
R15  
Salads  
Baby Meals  
Toddlers Food  
R2  
R3  
Soups  
Pancakes  
Tomato soup  
Pumpkin soup  
Pancakes  
Crepes  
Makes 10 – 12  
1 tablespoon oil  
2 cloves garlic, crushed  
1 brown onion, peeled and diced  
2 x 410g cans diced tomatoes  
1 tablespoon tomato paste  
2 teaspoons brown sugar  
2 tablespoons cooking oil  
1 brown onion diced  
2 cloves garlic, crushed  
400g Butternut pumpkin, peeled and diced  
4 cups (1litre) chicken stock  
Makes approximately 8-10 pancakes  
1
3 x 60g eggs, lightly beaten  
4
1 ⁄ cups milk  
1
4
1 ⁄ cups milk  
1 x 60g egg  
2 tablespoons butter, softened  
2 tablespoons butter, melted  
1 teaspoon vanilla essence  
1 cup plain flour  
1
1
2
1 ⁄ cups plain flour  
2
⁄ teaspoon salt  
1
4
⁄ teaspoon salt  
3 cups (750ml) vegetable stock or water  
1. Heat oil in a hot saucepan, add onions and garlic  
and sauté for 5 minutes.  
Extra butter, for greasing  
Extra butter, for greasing  
1. Heat oil in a large saucepan, add garlic and  
onions, cook over a medium heat for 2-3 minutes  
or until onion is soft.  
1. Place milk, egg, butter, flour and salt in the  
blender jug.  
2. Add the pumpkin and toss to coat with the onion  
mixture, then add the stock and bring the mixture  
to the boil.  
1. Add eggs, milk, butter, essence, flour and salt  
to the blender jug.  
2. Use speed 3 and mix to a smooth batter.  
2. Use speed 3 and mix to a smooth batter.  
2. Combine tomatoes, tomato paste, and brown  
sugar.  
3. Reduce heat to simmer for 20 minutes and cook  
with the lid on until the pumpkin is cooked.  
3. Heat a small greased frying pan over a moderate  
heat. Pour a small quantity of batter into frying  
pan then move batter around to cover base of pan.  
3. Lightly grease crepe pan and heat over a  
moderate heat.  
3. Pour into pan with onion mixture, add stock or  
water and bring to the boil, then reduce heat and  
simmer, uncovered for 20 minutes or until liquid  
has reduced by one third.  
4. Allow mixture to cool and transfer in batches to  
the blender jug.  
4. Pour sufficient batter into the pan to cover thinly  
and evenly.  
4. Cook until bubbles come to the surface and break.  
5. Use speed 4 and puree until smooth.  
5. Carefully turn the pancake over and cook until  
golden brown.  
5. Crepes will cook quickly in 1-2 minutes,  
overcooking causes crepes to toughen.  
6. Return pureed soup to the saucepan to heat  
through, check the seasoning before serving.  
4. Allow the mixture to cool, then transfer mixture  
into three batches into blender jug  
6. Remove from pan. Continue cooking with  
remaining batter.  
6. Carefully turn crepes over and cook until golden.  
Serve with raspberry sauce  
5. Use speed 4 and puree until smooth.  
Serve with maple syrup and ice cream.  
Raspberry Sauce  
250g fresh or frozen raspberries  
1
4
⁄ cup icing sugar  
2 tablespoons Grand Marnier or orange liqueur  
2 tablespoons water  
1. Place raspberries, icing sugar, Grand Marnier and  
water into blender jug.  
2. Use speed 3 and mix until smooth.  
Spoon over crepes and serve.  
R5  
R4  
Cocktails  
Non-alcoholic drinks  
Margarita  
Daiquiris  
Fruit cocktail  
Rockmelon and pineapple frappé  
60 ml Tequila  
60 ml Cointreau  
80 ml lime juice  
12 ice cubes  
Basic recipe  
250 ml pineapple juice  
1 cup chopped rockmelon  
1 cup canned pineapple pieces  
1 cup ice  
Fruit (approximately 1 cup)  
120 ml white spirits (white rum, vodka or kirsch)  
60 ml sugar syrup  
1 banana, peeled and chopped  
1 orange, skin and pith removed then quartered  
250 ml soda water  
Mint leaves, to serve  
1 cup ice  
2 tablespoons passionfruit pulp  
1. Place Tequila, Cointreau, lime juice and ice cubes  
into blender jug.  
1. Place rockmelon, pineapple and ice into the  
blender jug.  
1. Place all ingredients into the blender jug.  
2. Use speed 5 and puree until smooth.  
1. Place pineapple juice, banana, and orange into  
blender jug.  
2. Use speed 5 and blend until well combined and  
ice is crushed.  
2. Use speed 5 and blend until all ingredients are  
crushed and mixture is smooth and thick.  
2. Use speed 5 and blend until well combined.  
Most fresh fruit and berries can be used, if using  
frozen fruit defrost before use. Fruit with hard skins or  
stones must have them removed before pureeing.  
Large fruit must be diced first.  
Serve in salt rimmed glasses.  
3. Stir in passionfruit pulp and soda water and serve.  
3. Serve with chopped mint leaves.  
R6  
R7  
Smoothies and Milkshakes  
Recipes for use with Food Processor  
Mango Smoothie  
Strawberry Smoothie  
Smoked Salmon Pate  
1 mango, peeled and sliced  
150 g strawberries  
250 ml milk  
1 teaspoon grated lemon rind  
1 tablespoon lemon juice  
3
4
⁄ cup unflavoured yogurt  
120 ml orange juice  
2 scoops vanilla ice cream  
Strawberry topping, to serve  
75g cream cheese  
75g smoked fish, skin and bones removed (salmon,  
trout or mackerel)  
1 teaspoon horseradish cream  
1 teaspoon fresh parsley sprigs  
White pepper, to taste  
1. Place mango, yogurt and orange juice into  
blender jug.  
1. Place strawberries, milk and ice cream into the  
blender jug.  
2. Use speed 5 and blend until smooth.  
Serve immediately.  
2. Use speed 5 and blend until smooth  
and combined.  
1. Assemble food processor using the chopping blade.  
Serve with strawberry topping drizzled over top.  
2. Place lemon rind, juice and cream cheese into food  
processor bowl and process until smooth using the  
CHOP (button 2) function.  
3. Add fish, horseradish cream, parsley and pepper  
and process for 10-15 seconds.  
4. Scrape mixture from sides of bowl with a spatula.  
5. Process mixture in short bursts until smooth.  
6. Cover and refrigerate until well chilled.  
Serve with water biscuits or Melba toasts.  
R8  
R9  
Sauces and Dressings  
Main Meals  
Herb Dressing  
Satay Sauce  
Tandoori-Style Fish  
Lamburgers  
6
1
4
3-4  
3
4
⁄ cup mixed fresh herbs (parsley, coriander, mint,  
2 cloves garlic  
1 small onion  
Rind and juice of 1 lemon  
125g natural yogurt  
1 onion, cut into quarters  
4 cloves garlic  
1 tablespoon fresh herb sprigs (parsley,  
coriander or rosemary)  
chives, rosemary, and basil)  
1 clove garlic, optional  
2 tablespoons olive oil  
2 teaspoons peanut oil  
1 slice bread, crusts removed  
1
1
2
2
⁄ cup roasted peanuts  
⁄ small onion, quartered  
3 tablespoons balsamic vinegar  
1 small chilli, halved and seeded  
1 teaspoon ground cumin  
200g Trim Lamb, diced  
1 tablespoon mint sauce  
Salt and pepper, to taste  
3
4
⁄ cup water  
1 teaspoon ground coriander  
1
2
1. Assemble food processor using the chopping blade.  
2 tablespoons lemon juice  
1 tablespoon dark soy sauce  
2 tablespoons coconut milk  
1 teaspoon brown sugar  
⁄ teaspoon paprika  
Sprinkle of cayenne pepper  
4 Atlantic salmon cutlets  
2. Place herbs and garlic into food processor bowl  
and process until chopped finely using the CHOP  
(button 2) function.  
1. Assemble food processor using the chopping blade.  
2. Place herbs, bread, onion and lamb into food  
processor bowl in two batches and process 10-15  
seconds using BLEND (button 5) function.  
1. Assemble food processor using the chopping blade.  
3. Add oil and vinegar and process until combined.  
Serve with lamb, chicken or fish.  
1. Assemble food processor using the chopping blade.  
2. Place rind, juice, yoghurt, onion, garlic and spices  
into processing bowl and process until smooth  
using the CHOP (button 2) function.  
2. Place garlic and onion into processing bowl and  
chop in quick bursts using the CHOP (button 2)  
function.  
3. Place processed ingredients into a mixing bowl,  
add mint sauce and seasonings and mix well.  
3. Arrange salmon cutlets in a shallow glass or  
ceramic container. Coat salmon with smooth paste,  
cover and refrigerate for 2 hours.  
Mayonnaise  
2-3  
4. Shape mixture into 3-4 burgers, cover and  
refrigerate 20-30 minutes.  
3. Heat oil in a saucepan and cook garlic and onion  
mixture until lightly browned.  
5. Cook burgers on a preheated grill or pan fry for 5  
minutes each side or until cooked when tested.  
2 egg yolks  
1 teaspoon dry mustard  
1 tablespoon vinegar  
4. Place remaining ingredients into food processor  
bowl and process until smooth.  
4. Cook salmon cutlets on a preheated grill or  
barbeque for 3 minutes each side or until fish is  
cooked when tested.  
5. Pour combined mixture over garlic and onion  
mixture and stir over a gentle heat to warm  
through.  
Salt and white pepper, to taste  
1
2
⁄ cup vegetable oil  
1. Assemble food processor using the chopping blade.  
Serve immediately or cover and store in  
the refrigerator.  
2. Place egg yolks, mustard, salt and pepper into  
food processor bowl and process for 10-15 seconds  
using the STIR (button 1) function.  
Satay Sauce may thicken on standing, if this  
happens stir in a little more warm water.  
3. With the motor running, add the oil slowly through  
the feed chute on top of the processing lid and  
process until smooth. DO NOT OVER-PROCESS.  
Note  
4. Taste and adjust seasoning with extra salt, pepper  
and vinegar if required.  
5. Cover and store in the refrigerator.  
R10  
R11  
Salads  
Cakes  
Coleslaw  
Carrot and Zucchini Cake  
3 sticks celery  
3 small zucchinis  
2 carrots  
3 x 60g eggs  
2 cups sugar  
4 shallots  
1
4
⁄ red cabbage, separate leaves and roll  
into bundles  
1
4
⁄ white cabbage, separate leaves and roll  
3 teaspoons vanilla  
1
2
into bundles  
⁄ cup oil  
2 carrots, peeled  
2 green apples, cored and quartered  
1 red capsicum  
1 cup walnuts, finely chopped  
1
2
2 ⁄ cups self raising flour  
1
4
⁄ teaspoon baking powder  
210g can pineapple pieces, drained  
125g can corn nibbles, drained  
1 cup mayonnaise  
1 teaspoon salt  
2 teaspoons cinnamon  
1. Assemble food processor using the shredding disc.  
2. Grate zucchinis and carrots, set aside.  
1. Assemble food processor using the slicing disc.  
2. Use button 3 to slice celery, shallots and cabbage,  
place into a large bowl.  
3. In a mixing bowl, beat the eggs until pale in  
colour. Add the sugar, vanilla and oil, process until  
slightly thickened. Add walnuts, zucchinis and  
carrots, flour, baking powder, salt and cinnamon,  
mix until well combined.  
3. Reverse the disc to the shredding side and use  
button 3 to grate carrots.  
4. Remove the slicing\shredding disc and insert the  
chopping blade. Use the Pulse button to process  
apple, capsicum and pineapple until chopped.  
4. Pour mixture into 2 well greased and base lined  
20cm cake pans.  
5. Add chopped mixture to the sliced vegetables. Add  
corn and mayonnaise and toss all ingredients until  
well combined.  
5. Bake in a preheated moderate oven 180ºC for  
40-45 minutes or until cooked when tested.  
When mixing cakes do not over mix as this will  
toughen the mixture.  
6. Refrigerate until ready to serve.  
Note  
R12  
R13  
Baby Meals  
Toddlers Food  
A baby's first foods will influence their life long  
eating habits. The food processor is ideal for  
processing small quantities of nutritious baby food.  
As baby gets older the digestive system becomes  
stronger and is able to digest foods like egg yolks,  
fish and cottage cheese.  
Apple and Banana Custard  
Baby Muesli  
1
2
⁄ small apple, cored  
1 tablespoon rolled oats  
2 tablespoons baby rice cereal  
1 small banana, peeled and diced  
1⁄2 cup prepared baby custard  
Baby may also prefer food less smooth. For slightly  
coarser textured food simply puree for less time.  
1 teaspoon sultanas  
First Foods  
1
2
⁄ small apples, peeled, sliced  
These recipes are ideal for baby's first taste  
experience. They are easily digested and suitable for  
babies under 12 months old.  
These recipes are suitable for babies over 12 months  
of age.  
1. Cook apple until just soft. Cool.  
4 tablespoons prepared formula milk  
2. Assemble food processor using chopping blade.  
1. Assemble Food processor using chopping blade.  
3. Place cooled apple and banana into food processor  
bowl and PUREE (button 4) until smooth.  
Fast Fish  
2. Place oats, cereal, sultanas and apple into food  
processor bowl and roughly chop for 5-10 seconds  
using button 4.  
Golden Puree  
100g tuna or other cooked flaked fish, bones  
removed  
1
4. Fold fruit into custard.  
2
⁄ small sweet potato, peeled and sliced  
Serve immediately to avoid fruit discolouring.  
3 baby squash, trimmed and halved  
1 zucchini, sliced and cooked  
3. Continue processing and add milk through the feed  
chute to achieve desired consistency.  
1
2
⁄ potato, diced and cooked  
1. Assemble food processor with the chopping blade.  
4. Warm before serving.  
2. Place sweet potato into processing bowl and  
roughly chop for 5-10 seconds using button 4.  
1. Assemble Food processor using chopping blade.  
2. Place cooled ingredients into food processor bowl  
and puree (button 4) until smooth.  
3. Cook chopped sweet potato and squash in a  
microwave oven or steamer until tender. Cool.  
Serve chilled or warm.  
4. Return cooled vegetables to processing bowl and  
PUREE (button 4) until smooth.  
Creamy Chicken and Apricot  
5 dried apricots  
Avocado and Pear  
75g boneless chicken, diced  
200mls chicken stock or water  
1 tablespoon natural yoghurt  
1
2
⁄ ripe pear, peeled and halved  
1
2
⁄ avocado, stoned and peeled  
1. Assemble Food processor using chopping blade.  
1. Assemble Food Processor using chopping blade.  
2. Place ingredients into food processor bowl and  
PUREE (button 4) until smooth.  
2. Place apricots into food processor bowl and  
roughly chop using button 4.  
Serve immediately to avoid fruit discolouring.  
3. Combine apricots, chicken and stock in a small  
saucepan, bring to the boil, reduce heat and  
simmer 10-12 minutes or until chicken is cooked.  
Cool slightly.  
4. Place cooled ingredients into food processor bowl  
and puree (button 4) until smooth. Add yoghurt  
and blend into chicken mixture using button 4.  
5. Warm before serving.  
R14  
R15  
Notes  
Notes  
R16  
R17  

Advent TOCLS OE100 User Manual
A O Smith 750 1000 User Manual
Canon 2536A004 User Manual
Casio Scientific Calculator FX300ESPLUSPK User Manual
Channel Plus H721 User Manual
Clarion DGL373 User Manual
Crate Amplifiers BX 15 User Manual
Directed Electronics OHV1021A User Manual
Dual XIA3145 User Manual
JVC GET0075 001A User Manual