Bose Bluetooth Bluetooth Headset Series II User Manual

BOSE® BLUETOOTH® HEADSET  
SERIES 2  
|
|
|
|
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Safety Information  
Please read this guide  
Please take the time to follow the  
instructions in this owner’s guide carefully.  
It will help you set up and operate your  
product properly and enjoy its advanced  
features. Please save this owner’s guide  
for future reference.  
WARNINGS:  
• Contains small parts, which may be  
a choking hazard. Not suitable for  
children under age 3.  
To reduce the risk of fire or electrical  
shock, do not expose the product to  
rain or moisture.  
• Do not expose this apparatus to dripping  
or splashing and do not place objects  
filled with liquids on or near the apparatus.  
As with any electronic product, use care  
not to spill liquids into any part of the  
system. Liquids can cause a failure and/or  
a fire hazard.  
• Do not place naked flame sources,  
such as lighted candles, on or near  
the apparatus.  
• This product is intended to be used only  
with the power supply provided.  
The lightning flash with arrowhead  
symbol, within an equilateral  
triangle, alerts the user to the  
presence of uninsulated  
dangerous voltage within the  
system enclosure that may be  
of sufficient magnitude to  
• Where the mains plug is used as the  
disconnect device, such disconnect  
device shall remain readily operable.  
constitute a risk of electric shock.  
The exclamation point within an  
equilateral triangle alerts the user  
to the presence of important  
operating and maintenance  
Do not disassemble, heat above 100º C  
(212º F), or incinerate.  
• Do not use your headset while it is  
connected to the charger.  
instructions in this owner’s guide.  
• Do not use the headset at high volume  
for an extended period of time. Doing so  
can cause hearing loss. Always listen at  
moderate levels.  
©2011 Bose Corporation. No part of this work may be reproduced, modified, distributed, or  
otherwise used without prior written permission.  
2
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
CAUTIONS:  
Important Safety  
• Make no modification to the system or  
accessories. Unauthorized alterations may  
compromise safety, regulatory  
compliance, and system performance and  
may void the warranty.  
Information  
1. Read these instructions – for all  
components before using this  
product.  
• Operate this product within the tempera-  
ture range of -4°F to 113°F (-20°C to  
45°C) only. Damage caused by use out-  
side of that range may not be covered by  
the warranty.  
2. Keep these instructions – for future  
reference.  
3. Heed all warnings – on the product  
and in the owner’s guide.  
• Check and follow local laws regarding  
use of a mobile phone and headset/  
headphones while operating any vehicle  
or using equipment that requires your full  
attention. If you use the headset/  
4. Follow all instructions.  
5. Do not use this apparatus near  
water or moisture – Do not use this  
product near a bathtub, washbowl,  
kitchen sink, laundry tub, in a wet  
basement, near a swimming pool,  
or anywhere else that water or  
moisture are present.  
headphones while engaging in any such  
activity, be sure to focus on safety.  
Bose Corporation hereby declares  
that this product is in compliance with  
the essential requirements and other  
relevant provisions of Directive 1999/  
5/EC and other applicable Directives.  
The complete Declaration of  
6. Clean only as directed by Bose  
Corporation. Unplug this product  
from the wall outlet before cleaning.  
7. Do not install near any heat  
sources, such as radiators,  
heat registers, stoves, or other  
apparatus (including amplifiers)  
that produce heat.  
Conformity can be found at  
3
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
8. Protect the USB cord from being  
walked on or pinched, particularly  
at the power supply end and the  
point where it exits from the  
apparatus.  
12. To prevent risk of fire or electric  
shock, avoid overloading wall  
outlets, extension cords, or integral  
convenience receptacles.  
13. Do not let objects or liquids enter  
the product – as they may touch  
dangerous voltage points or short-out  
parts that could result in a fire or  
electric shock.  
9. Only use attachments/accessories  
specified by the manufacturer.  
10. Unplug this apparatus during light-  
ning storms or when unused for  
long periods of time – to prevent  
damage to this product.  
14. Use proper power sources –  
Plug the product into a proper power  
source, as described in the operating  
instructions or as marked on the  
product.  
11. Refer all servicing to qualified  
service personnel. Servicing is  
required when the apparatus has  
been damaged in any way: such  
as USB cord or power supply is  
damaged; liquid has been spilled  
or objects have fallen into the  
apparatus; the apparatus has been  
exposed to rain or moisture, does  
not operate normally, or has been  
dropped – Do not attempt to service  
this product yourself. Opening or  
removing covers may expose you to  
dangerous voltages or other hazards.  
Please call Bose Customer Service to  
be referred to an authorized service  
center near you.  
4
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
This device complies with FCC and  
Industry Canada RF radiation exposure  
limits set forth for general population.  
It must not be co-located or be operating  
in conjunction with any other antenna or  
transmitter.  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the  
equipment and receiver.  
• Connect the equipment to an outlet on a  
different circuit than the one to which the  
receiver is connected.  
• Consult the dealer or an experienced  
radio/TV technician for help.  
In the United States:  
This equipment has been tested and  
found to comply with the limits for a Class  
B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to  
provide reasonable protection against  
harmful interference in a residential  
installation. This equipment generates,  
uses, and can radiate radio frequency  
energy and, if not installed and used in  
accordance with the instructions, may  
cause harmful interference to radio  
communications. However, this is no  
guarantee that interference will not  
occur in a particular installation. If  
this equipment does cause harmful  
interference to radio or television  
Changes or modifications not expressly  
approved by Bose Corporation could  
void the user’s authority to operate  
this equipment.  
In USA and Canada:  
This device complies with part 15 of the  
FCC rules and Industry Canada license-  
exempt RSS standard(s). Operation is  
subject to the following two conditions:  
(1) this device may not cause harmful  
interference, and (2) this device must  
accept any interference received,  
including interference that may cause  
undesired operation.  
reception, which can be determined by  
turning the equipment off and on, you  
are encouraged to try to correct the  
interference by one or more of the  
following measures:  
Attribution  
The Bluetooth® word mark and logos are  
registered trademarks of Bluetooth SIG,  
Inc. and any use of such marks by Bose  
Corporation is under license.  
5
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Other agency markings  
FCC ID: A94BT2R  
FCC ID: A94BT2L  
IC: 3232A-BT2R  
IC: 3232A-BT2L  
Engineered in the United States  
Made in China  
Meets IDA Requirements  
Names and Contents of Toxic or Hazardous Substances or Elements  
Toxic or Hazardous Substances and Elements  
Part  
Name  
Lead Mercury Cadmium Hexavalent Polybrominated  
Polybrominated  
(Pb) (Hg)  
(Cd)  
(CR(VI))  
Biphenyl (PBB) diphenylether (PBDE)  
PCBs  
X
X
0
0
0
0
0
0
0
0
Metal  
parts  
0
0
Plastic  
parts  
0
X
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Speakers  
Cables  
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous  
materials for this part is below the limit requirement in SJ/T 11363-2006.  
X: Indicates that this toxic or hazardous substance contained in at least one of the  
homogeneous materials used for this part is above the limit requirement in SJ/T  
11363-2006.  
6
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Using the headset  
8
Thank you . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
8
8
9
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Initial pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Wearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Recognizing the lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Basic call actions and audio tones . . . . . . . . . . . . . . . . . . . . 17  
Multi-point pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Connection priority for multiple paired phones . . . . . . . . . . . 20  
Multi-point call actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Reference  
21  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Customer service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Technical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
7
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Using the headset  
Thank you  
We appreciate your choice of the Bose® Bluetooth® headset  
Series 2, which lets you hear and be heard, even as noise levels  
around you change.  
Features  
Small size, advanced fit, and simple controls.  
StayHeartip  
(medium)  
USB  
connector  
Volume  
+ and – buttons  
Bluetooth  
indicator  
Call  
button  
Power  
Battery  
indicator  
on/off  
8
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Features and Functions  
Talk time  
Up to 4.5 hours.  
Standby time  
Up to 100 hours.  
Multipoint pairing  
Maintain two active phone connections at once.  
Adaptive audio adjustment  
Hear what is being said, even as noise levels around you change,  
with automatic volume adjustment.  
A2DP audio streaming  
Listen to podcasts, audio books, turn-by-turn directions, or  
other audio sources streamed directly from your mobile device.  
Automatically connects when an audio source is played.  
9
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Included with headset:  
Additional StayHear™  
tips (small and large)  
USB cable  
Carry case  
Power supply  
(where needed)  
Power supply  
adapters  
(where needed)  
10  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Charging  
Although the battery is partially charged at the factory, it is  
important to fully charge the battery before first use. Allow  
up to 3 hours for a full charge.  
1. Plug the small end of the USB  
cable into the headset.  
2. Plug the large end of the cable  
into the power supply or a  
powered USB connector on  
your computer.  
3. Battery indicator light will  
blink yellow while charging  
and turn green when charging  
is complete.  
Note: The headset will not operate while charging.  
Note: Before charging, be sure the headset is at room temperature,  
between 41°F (5°C) and 104°F (40°C).  
11  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Attaching adapters (if needed):  
1. Extend the power supply prongs.  
2. If needed, snap on the adapter for your region (2a).  
To remove an adapter, press back on the release and lift the  
adapter up and off (2b).  
1
2a  
2b  
Europe  
UK  
3. Plug the power supply into an AC (mains) wall outlet.  
12  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Initial pairing  
Bluetooth light  
and symbol  
1. Ensure the mobile phone is on and  
Bluetooth® is enabled. Turn on the  
headset by sliding the power switch  
to the On (green) position.  
The Bluetooth indicator slowly  
flashes blue to indicate the headset  
is discoverable.  
2. Locate the Bluetooth device list  
on the mobile phone and select  
Bose BT2.  
3. If prompted for a passkey, enter  
0000  
.
The Bluetooth indicator flashes,  
then turns solid blue to indicate a  
successful connection.  
Bluetooth  
device list  
Additional pairing (up to 6 phones):  
Press and hold Call for 5 seconds to  
make the headset discoverable.Then repeat steps 2 to 3 above.  
Note: If you have difficulty pairing, see “Troubleshooting”, beginning  
on page 21.  
13  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Fitting  
The soft StayHeartip allows the headset to rest comfortably in  
your ear. Choose the tip that is the right size for your ear.  
To change the tip:  
1. Gently remove the tip from the ear-  
Tip  
wing  
piece. Do not pull on the tip wing.  
Nozzle  
hook  
2. Ease the new tip over the base of the  
earpiece until it latches onto the  
nozzle hook.  
Wearing  
Slot  
1. Place the headset into your ear,  
pointing straight down.  
2. Then twist the headset upwards so it  
points directly at your mouth.  
3. Press the tip wing under the ear  
ridge.  
2
3
1
14  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Recognizing the lights  
Battery Indicator  
Color  
Status while on:  
Status while charging:  
Green  
1.5 - 4.5 hours remaining  
talk time.  
(Solid)  
Charging is complete.  
Yellow  
Red  
10 minutes - 1.5 hours  
remaining talk time.  
(Flashing)  
Charging is ongoing.  
(Flashing)  
(Solid)  
About 10 minutes remaining Charging error.  
talk time.  
Room temperature or  
product may be too  
warm or too cold.  
15  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Bluetooth® Indicator  
Color  
Indicates:  
The headset is discoverable for pairing.  
Blue (slow flash)  
Blue (quick flash) The headset is attempting to connect to a  
mobile phone or is receiving or making a call.  
The headset and a paired mobile phone are  
not connected. One of them is not turned on,  
or the two are more than 33 feet (10m) apart.  
Blue (solid)  
The headset is connected for calls.  
Purple (solid)  
The headset is connected for A2DP audio  
streaming.  
Note: Except when charging, indicators shut off after 10 seconds to  
conserve battery power.  
16  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Basic call actions and audio tones  
Action  
Headset control  
Press Call once.  
Audio tone  
Answer a call  
Single beep  
Make a call  
Press Call once. Use  
voice commands or the  
phone keypad to select  
and dial.  
Single beep  
End a call  
Press Call once.  
Two notes  
(descending)  
Adjust the volume Press Volume + or  
-
while One note per  
on a call or streaming  
audio.  
press  
Mute/Unmute  
a call  
Press Volume + and  
at the same time.  
Short double beep  
Single tone  
repeats every 30  
seconds  
Transfer the audio Press and hold Call  
None  
to your mobile  
phone  
(during a single phone  
call only) for 5 seconds or  
until transfer is complete.  
Last number redial Press Call twice.  
Old-style phone  
ringing  
17  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Reject an incoming Press and hold Call for  
Two notes  
(descending)  
call  
3 seconds.  
Call waiting  
Press Call to answer  
second call and place  
first call on hold.  
Single beep  
Switch between  
two calls  
Press Call twice.  
Single beep  
Begin  
conferencing  
Press and hold Call for 3 Single beep  
seconds while two calls  
are active.  
Low battery  
None.  
Five-note warble  
Repeats every  
2 minutes  
Bluetooth® device None.  
connected  
Three quick notes  
(ascending)  
Bluetooth device  
disconnected  
None.  
Three quick notes  
(descending)  
Power on  
Power off  
Slide Power switch to  
Four notes  
(ascending)  
On position (green).  
Slide Power switch to  
Off position (red).  
Four notes  
(descending)  
18  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Multi-point pairing  
To maintain an active connection with two different mobile devices  
at the same time:  
1. Disable the Bluetooth® connectivity on any phones previously  
paired to the headset.  
2. Turn on the headset and the mobile phone.  
3. Press and hold Call and Volume + for 5 seconds.  
4. Complete the pairing procedure specific to your phone.  
5. Turn the headset off and then on again.  
6. Repeat steps 2 - 5 for the second phone.  
Disabling multi-point pairing  
1. Press and hold Call and Volume – buttons for 10 seconds.  
2. Turn the headset off and then on again.  
3. Re-pair the desired mobile phone.  
Note: Some phones require you to remove Bose BT2 from the  
Bluetooth device list before you can re-pair to that phone.  
19  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Connection priority for multiple paired phones  
The last phone used for a call will have first priority for calls, voice  
dialing and redial.  
To make a call with the other connected phone, place the call  
manually. First priority then switches to this phone.  
To establish priority for any other paired phone, reconnect with  
that device by selecting Bose BT2 in the device list.  
Multi-point call actions  
In multi-point operation, call actions are the same as listed  
on page 17. To switch between active calls on two phones,  
press Call twice.  
20  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Reference  
Troubleshooting  
Problem  
What to do  
The headset has • Make sure both ends of the USB cable are firmly  
short talk time.  
connected.  
• If you are using a power outlet:  
Be sure the power supply is securely  
plugged in and the outlet is working.  
Be sure to use the proper power supply  
adapter (if one is needed in your region).  
• If you are using your computer, be sure the  
computer is plugged in and the USB port is  
powered.  
Note: The battery indicator will blink yellow while  
charging and turn green when charge is com-  
plete.  
• Make sure the room temperature is between  
41°F and 104°F (5°C and 40°C) and the product  
is at room temperature before charging begins.  
Note: The battery indicator glows a steady red if  
the room or product is too warm or cold.  
21  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
The headset  
does not fit  
p ro p e r l y o r f e e l s  
uncomfortable.  
• Make sure the headset is in the correct ear and  
the wing on the StayHear™ tip is flush beneath  
the ear ridge. (Refer to "Wearing" on page 14.)  
• Make sure the tip is firmly attached to the  
headset.  
Try the large or small tip.  
The mobile  
phone and the  
headset do not  
pair.  
• Make sure both the headset and mobile phone  
are turned on and the Bluetooth® feature on your  
phone is activated. Refer to your phone  
instruction manual for details.  
Turn the headset off, then on again.  
• Press Call for at least 5 seconds to make the  
headset discoverable, then attempt to pair  
again.  
• Make sure the phone is within 33 feet (10  
meters) of the headset.  
Turn the phone power off, then on again and  
attempt to pair again.  
22  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
The mobile  
• Make sure both devices are turned on and  
Bluetooth® connectivity is enabled on the  
phone.  
Turn the headset off, then on again. Make sure  
the mobile phone is within 33 feet (10 meters)  
of the headset.  
phone and the  
headset do not  
connect.  
• Check the Bluetooth device list on your phone  
to be sure Bose BT2 is selected.  
If it is selected, delete it from the list (refer to  
your phone instruction manual for details).  
If it is no longer listed, repeat “Additional  
pairing” on page 13.  
• Simultaneously hold Call and Volume – for  
5 seconds to reset the memory, and pair the  
headset to the phone again.  
Turn the phone power off, then on again.  
What you  
hear on the  
headset is not  
clear.  
• During a call, adjust the volume on your  
mobile phone or on the headset by pressing  
Volume + or  
.
• Check your mobile phone signal strength.  
• Make sure the mobile phone is within 33 feet  
(10 meters) of the headset.  
• Reposition the headset. Refer to “Fitting” on  
page 14.  
• Clean the wire mesh under the tip. See page 26.  
23  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
What the other  
person hears is  
not clear.  
• Move the mobile phone closer to your headset.  
• Make sure the phone is not near other wireless  
equipment.  
• Reposition the headset. Refer to “Fitting” on  
page 14.  
• Check your mobile phone signal strength.  
Turn the phone power off, then on again.  
A call  
disconnects  
unexpectedly.  
• Check the headset to make sure it is on and  
charged.  
• Make sure the mobile phone is within 33 feet  
(10 meters) of the headset.  
• Check the signal strength on your phone and  
make sure the battery is sufficiently charged.  
No audio from a • Make sure the device supports A2DP audio  
streaming audio  
source or  
application.  
streaming. (The Bluetooth® indicator will glow  
purple.)  
• Make sure the device’s Bluetooth volume is  
turned up and not muted.  
• Make sure the streaming audio source is on and  
playing.  
• Move the device closer to the headset.  
Try another streaming audio application.  
Turn the phone power off, then on again.  
24  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Poor sound  
quality from a  
streaming audio  
source or  
• Move the device closer to the headset.  
• Move the device and headset away from any  
device that could cause interference, such as  
another Bluetooth® enabled device, cordless  
phones, a microwave oven, or a wireless  
computer network router.  
application.  
• Reduce the number of Bluetooth applications  
that are running on your device. (Running multi-  
ple applications may reduce the amount of inter-  
nal resources available to transmit audio.  
Closing all non-essential applications may  
improve audio quality. Disabling Wi-Fi  
functionality on the device may also improve  
audio quality.  
Try another streaming audio application.  
Turn the phone power off, then on again.  
25  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Customer service  
For additional help in solving problems, contact your  
Bose® dealer. Or for online support visit:  
• owners.Bose.com in the U.S.  
• global.Bose.com outside the U.S.  
To contact Bose by phone, refer to the address list on the inside  
back cover of this guide.  
Maintenance  
Battery care:  
1. Be sure to turn off the headset when it is not in use.  
2. Before storing the headset for more than a few months, be  
sure the battery is fully charged.  
To clean the headset:  
Use a soft, dry cloth to wipe the surface carefully. Do not use  
liquids or sprays.  
To clean the tip:  
Gently peel the tip from the end of the earpiece. Wash the tip with  
mild soap and rinse. Dry with a soft cloth. Be sure the tip is  
completely dry before reattaching to the headset.  
To clean the wire mesh under the tip:  
Gently peel the tip from the end of the earpiece. Lightly brush the  
mesh screen with a soft, dry cloth. Avoid pressing on the mesh,  
which could push debris through the mesh and into the headset.  
26  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Limited Warranty  
Your Bose® Bluetooth® headset Series 2 is covered by a limited  
warranty. Details of the limited warranty are provided on the  
product registration card that is included in the carton. Please refer  
to the card for instructions on how to register. Failure to register  
will not affect your limited warranty rights.  
To obtain Limited Warranty service  
Return the product, with proof of purchase from an authorized  
Bose dealer, as follows:  
1. Contact the Bose organization in your country/region (visit  
Global.Bose.com for contact information in your country/  
region) for specific return and shipping instructions.  
2. Label and ship the product, freight prepaid, to the address  
provided by the Bose organization in your country.  
3. Place any necessary Return Authorization Number prominently  
on the outside of the carton. Cartons not bearing a Return  
Authorization Number, where required, will be refused.  
Note: The serial number is located on the warranty card included in  
the carton.  
27  
Tab 6, 12  
Tab 5, 11 Tab 4, 10, 16 Tab 3, 9, 15 Tab 2, 8, 14  
English  
Technical information  
Weight: 0.42 ounces (12 grams)  
Power supply rating:  
Input: 100 VAC to 240 VAC, 0.15A  
Output: 5V, 1A  
Temperature ranges:  
Operate this product within the temperature range of -4°F to 113°F  
(-20°C to 45°C) only.  
Store this product within the temperature range of -4°F to 113°F  
(-20°C to 45°C) only.  
Charge the battery where the temperature is between 41°F and  
104°F (5°C and 40°C) only.  
Battery:  
Rechargeable, non-replaceable lithium-ion polymer.  
Charging time: 3 hours for full charge.  
Use with a fully charged battery: up to 4.5 hours of talk time or 100  
hours of standby time. Talk time may vary with specific mobile  
phones.  
28  
English  
Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, 16 Tab 5, 11  
Tab 6, 12  
Bluetooth® QD ID: B018073  
Version 2.1 Enhance Data Rate (EDR) and Secure Simple  
Pairing (SSP).  
Profiles include Headset (HSP 1.1), Hands Free (HFP 1.5), and  
Advanced Audio Distribution Profile (A2DP 1.2).  
Accessories  
To replace the supplied StayHear™ tips, carry case, power  
supply, power supply with adapters, or adapters only, visit  
global.Bose.com, or contact Bose® Customer Service.  
To purchase an optional headset charger for your vehicle,  
contact your authorized Bose dealer or Bose Customer Service.  
To contact Bose by phone, refer to the address list on the inside  
back cover of this guide.  
29  
BOSE CORPORATION  
USA  
Denmark  
2605 Brondby  
04343-7777  
Italia  
The Mountain,  
Framingham, MA, 01701  
877-335-2073  
owners.Bose.com  
Via della Magliana 876  
Roma, 00148  
06.60.292.555  
Deutschland  
D-61381 Friedrichsdorf  
06172-71040  
Canada  
Japan  
9133 Leslie Street,  
Suite 120, L4B 4N1  
877-701-2175  
Bose K.K.  
Shibuya YT Building  
28-3 Maruyama-cho  
Shibuya-ku,Tokyo  
150-0044  
France  
78100 Saint Germain en  
Laye  
Australia  
TEL 0570-080-021  
FAX 03-5489-1041  
Unit 3/2 Holker  
01-30616363  
St.Newington NSW, 2127  
1800 023 367  
India  
Mexico  
Shriram Bhartiya Kala  
Kendra, 1 Copernicus  
Marg, New Delhi, 100-001  
91-11-2307-3825-3826-  
3827  
Paseo de lasPalmas# 405,  
11000  
Belgique/Belgie  
B-3700 Tongeren  
012-390800  
52-55-52-02-35-45  
FAX: 52-55-52-02-41-95  
China  
Nederland  
1135 GE Edam  
0299-390111  
Ireland  
2203-2305 22F, West Gate  
Tower/1038 West Nanjing  
Road-MeiLongzhen Plaza,  
Shanghai, 200041  
Castlebury Road,  
Carrickmacross, Co  
Monaghan  
New Zealand  
0800 501 511  
86-22-62713000 ext. 162  
042-9671500  
Norge  
Hong Kong  
N-2213 Kongsvinger  
62-82-15-60  
Suite 1203, Midas Plaza, 1  
Tai Yau Street, San Po  
Kong, Kowloon, Hong  
Kong  
Österreich  
Wienerbergstrasse 7  
(10.OG)  
01-60404340  
(852) 21239000  
Finland  
Kornetintie 6b Helsinki, 380  
+358 10 778 6900  
Schweiz  
Hauptsrasse 134  
061-9757733  
Poland  
ul. Woloska 12  
Warszawa, 02-675  
+48 (0)22-8522928  
Sverige  
S-43153 Mölndal  
031-878850  
World Wide Web  
United Kingdom  
1 Ambley Green,  
Gillingham Business Park,  
Gillingham, Kent, ME8 ONJ  
0844-209-2630  
©2011 Bose Corporation, The Mountain,  
Framingham, MA 01701-9168 USA  
AM347801 Rev.01  

Arcam T31 User Manual
AudioBahn MULTIFUNCTIONAL SOURCE UNIT A3351 User Manual
Audiovox MM850 User Manual
Bryan Boilers BKS6000 User Manual
Canon Camcorder PC950 User Manual
GE 3504502P327 User Manual
HP (Hewlett Packard) HP 50g User Manual
Hypertec TSNBG20HY User Manual
Hypertec Z0102 User Manual
IDEAL INDUSTRIES ICOS HE24 User Manual