Blaupunkt IVMR 1042 User Manual

In Car Video  
IVMR-9002  
IVMR-1042  
7 607 003 586  
7 607 003 587  
Operating and installation instructions  
DEVICE OVERVIEW  
@ Cable for the interior lighting  
Ceiling-mounted monitor  
1 Lights on the main unit  
2 Light switch ON  
3 Monitor latch  
4 Vehicle interior lighting switch  
5 Loudspeaker  
(3 pin)  
Red = Electrical power supply  
(+12V)  
White = To the door switch  
(Door open = Earth)  
Black = Earth  
6 Infrared receiver for IR remote  
A
AUX sockets  
control IVRC-06  
Red RCA = Audio IN (R)  
White RCA = Audio IN (L)  
Yellow RCA = Video IN  
Infrared transmitter for IR head-  
phones IVHS-01 (accessory)  
7 Control button  
Increase the monitor volume /  
navigate in the OSD menu  
8 Control button  
Decrease the monitor volume /  
navigate in the OSD menu  
9 On/off button for the monitor  
: Control button MENU  
See Instructions / OSD menu.  
; Control button CH  
Channel selection if the monitor is  
connected to a signal controller  
IVSC-3302 or IVSC-5502.  
< LCD screen  
= Signal cable (13 pin)  
> System cable (13 pin)  
? Adapter cable RCA/jack (13 pin)  
17  
DEVICE OVERVIEW  
IR remote control  
D POWER  
On/off button for the monitor.  
E TV/VIDEO  
Input selector: switch between  
AV1 and AUX.  
D E F G  
F VOL • arrow button  
Increase the volume for the se-  
lected monitor.  
VOL • arrow button  
Decrease the volume for the se-  
lected monitor.  
H
I
G MUTE  
Mute the volume of the loud-  
speaker inside the monitor.  
H CH • arrow button  
/
Channel selection if the monitor is  
connected to a signal controller  
IVSC-3302 or IVSC-5502.  
Caution:  
/
The way the CH  
buttons  
J
function depends on the monitor  
selection, which is made using  
the signal controller’s remote con-  
trol.  
I MENU  
See Instructions / OSD menu.  
J Battery compartment  
18  
CONTENTS  
Device overview ..................... 16  
Ceiling-mounted monitor................ 17  
IR remote control........................... 18  
Contents................................. 19  
Notes for the user .................. 20  
Precautionary measures ................ 20  
Safety notices ........................ 21  
Supplied parts........................ 21  
Installing the monitor ............. 22  
Installing the monitor (mechanical) . 22  
Cables .......................................... 23  
Operation ............................... 24  
Controlling the interior lighting  
(monitor) ....................................... 24  
Opening the monitor...................... 24  
Adjusting the position of the  
monitor.......................................... 25  
Closing the monitor ....................... 25  
Switching on the monitor ............... 25  
OSD menu .................................... 26  
IR headphones IVHS-01  
(accessory) ................................... 26  
Changing the light bulb ................. 27  
Changing the battery in the  
remote control ............................... 27  
Specifcations ......................... 28  
IVMR-9002.................................... 28  
IVMR-1042.................................... 29  
19  
NOTES FOR THE USER  
Thank you for choosing a Blaupunkt  
product. We hope you enjoy using this  
new piece of equipment.  
Precautionary measures  
Please observe all the warning notices,  
precautionary measures and mainte-  
nance tips contained in these operat-  
ing instructions so as to extend the life  
of your monitor.  
Please read these operating instruc-  
tions before using the equipment for  
the first time.  
The Blaupunkt editors are constantly  
working on making the operating in-  
structions clearer and easier to under-  
stand. However, if you still have any  
questions on how to operate the device,  
please contact your dealer or the tele-  
phone hotline for your country. You will  
find the telephone number printed at the  
back of this booklet.  
If you are the driver you must never  
use the monitor during the journey  
in order to avoid causing a road ac-  
cident.  
Do not place the monitor in the fol-  
lowing positions:  
1. Positions in which it could  
restrict the driver’s view.  
2. Positions in which it could  
become a danger to safety  
(e.g. handbrake, steering wheel,  
gearshift lever and airbag).  
We provide a manufacturer guarantee  
for our products bought within the Eu-  
ropean Union. You can view the guar-  
or ask for them directly at:  
Only operate the device with the  
recommended voltage supply of  
12 V direct current.  
Blaupunkt GmbH  
Hotline  
Do not attempt to open or disman-  
tle the monitor, since you could suf-  
fer an electric shock as a result.  
Robert-Bosch-Str. 200  
31139 Hildesheim  
Germany  
If the monitor’s housing is dam-  
aged or broken, take it to your local  
specialist dealer or send it in to our  
customer service centre.  
We should like to point out that the right  
to make a claim under the guarantee  
could be forfeited if the device is  
changed or modified in any way with-  
out the express authorization of the  
manufacturer.  
Avoid using the monitor in environ-  
ments where it is subjected to dust,  
dirt or moisture.  
Long-term operation or storage outside  
the specific temperature range can lead  
to a shortening of the useful life of the  
LC display.  
Do not install the monitor in places  
where it is subjected to direct sun-  
light or extreme temperatures.  
20  
NOTES FOR THE USER  
SUPPLIED PARTS  
Note  
Supplied parts  
We recommend that you allow a spe-  
cialist workshop to carry out the instal-  
lation.  
The monitor is supplied with all the parts  
listed below. Please check that the  
range of parts supplied with your de-  
vice is complete. If one of the listed parts  
is missing, please contact your dealer  
immediately.  
Safety notices  
Please observe the following safety  
notices during installation and whilst  
making the connections.  
Monitor (including mounting fixture  
and screws)  
Remote control IVRC-06 with  
-
Disconnect the negative and posi-  
tive terminals of the battery.  
battery  
5 m long 13-pin system cable  
(for signal controller IVSC-3302 or  
IVSC-5502)  
-
When doing so, please observe the  
safety notices provided by the vehi-  
cle manufacturer.  
Connection adapter (13-pin RCA/  
-
Before drilling the holes necessary  
for mounting the equipment and for  
laying cables, please make sure  
that concealed cables, the fuel tank  
and fuel lines cannot be damaged  
in the process!  
jack)  
Operating instructions  
21  
INSTALLING THE MONITOR  
Installing the monitor  
(mechanical)  
Select a suitable position for secure  
installation of the monitor:  
The device must not distract the  
driver or restrict the driver’s view.  
Screws for securing the  
mounting plate  
The ability to enter and get out of  
the vehicle must not be impeded.  
The device must not be installed in  
such a way that could prevent the  
other vehicle components from  
functioning properly (e.g. sliding  
sunroof).  
Make sure that the device is in-  
stalled in a safe and secure posi-  
tion and that it cannot become de-  
tached in the event of an emergen-  
cy stop.  
Do not attach the device merely to  
Screws for securing the  
ceiling-mounted monitor  
the roof liner.  
If you need to drill additional holes,  
make sure you do not drill through  
the sheet metal of the vehicle’s  
roof.  
Avoid using the monitor over a  
longer period of time whilst the en-  
gine is off in order to prevent the  
battery from becoming discharged.  
22  
INSTALLING THE MONITOR  
Interior lighting connection (3 pin)  
Cables  
Red  
= Operating voltage (+12 V)  
White = To the door switch  
(Door open = Earth)  
>
?
Black = Earth  
To avoid discharging the battery, we  
recommend you use a switched oper-  
ating voltage (ignition).  
Warning notice: The operating voltage  
cable must be protected with at least a  
1.5 A fuse.  
Monitor connection (13 pin)  
System cable  
(13 pin)  
Adapter cable  
Connect the system cable (13 pin) >  
to a signal controller (IVSC-3302 or  
IVSC-5502). (The voltage supply is pro-  
vided by these devices. Operating in-  
structions are supplied with the devic-  
es).  
Cable for the  
interior lighting  
(3 pin)  
Or  
Signal cable  
(monitor hous-  
ing) (13 pin)  
Use the plug-in adapter cable ? to  
connect to the 12 V supply voltage and  
an external video/DVD device:  
@
=
Red  
= +12 V direct current  
= Earth  
Black  
Red RCA = Audio IN (R)  
White RCA = Audio IN (L)  
Yellow RCA = Video IN  
Jack plug  
(blue)  
= Do not use!  
(Only for special  
devices)  
23  
OPERATION  
Controlling the interior lighting  
(monitor)  
Opening the monitor  
Pull back the monitor release latch  
There are two switches for the lights:  
3 to flip down the LCD display.  
ON  
2 and interior lighting  
4.  
To watch television, lower the mon-  
itor until it is at an angle of approx.  
90° to the monitor’s base unit.  
ON  
:
This button is used to switch the lights  
on/off.  
Interior lighting  
:
3
If activated, the lights only come on  
when the vehicle’s doors are opened.  
2
4
24  
OPERATION  
Adjusting the position of the  
monitor  
The monitor can be rotated by up to  
approx. 30° to the right and left from its  
central viewing position.  
:
;
8
9 7  
D E F G  
Closing the monitor  
Turn the monitor back to its central  
viewing position and push it into its  
base unit so that it clips back into  
the releasing/locking mechanism.  
H
I
Switching on the monitor  
Press the power-on button 9 on the  
main unit or the button D on the re-  
mote control to switch the monitor on/  
off.  
Note:  
J
The button 9 lights up blue before the  
monitor is switched on. This means that  
the monitor is connected to the 12 V  
voltage supply.  
25  
OPERATION  
OSD menu  
Operation  
ZOOM (picture size)  
only IVMR-9002:  
Change the picture height/width  
Press the MENU button : on the  
display or the MENU button I on  
the remote control to open the  
OSD menu.  
- FULL  
- NORMAL  
- WIDE  
BRIGHTNESS:  
To adjust the brightness  
Use the arrow buttons 7 / 8 or  
I
/
to select the options. After  
CONTRAST:  
To adjust the contrast  
you press the MENU button : or  
I you can use the arrow buttons  
to change the settings.  
COLOR:  
To adjust the colour  
Select the “EXIT” option to close  
the OSD menu again.  
TINT:  
To adjust the picture shade (only  
for NTSC)  
REVOLVE:  
To revolve the screen display  
SPEAKER ON  
ZOOM  
BRIGHTNESS  
CONTRAST  
COLOR  
- LEFT - RIGHT:  
Mirror horizontally  
TINT  
- UP - DOWN:  
Mirror vertically  
REVOLVE LEFT-RIGHT  
UP-DOWN  
RESET PICTURE  
EXIT  
RESET PICTURE:  
To reset the configured parameters  
to the factory default settings.  
EXIT:  
SPEAKER ON  
To close the OSD menu  
Switch the internal loudspeaker on/  
off (same function as the MUTE  
button G on the remote control).  
IR headphones IVHS-01  
(accessory)  
The IR transmitter window 6 must not  
be covered up when using the IR head-  
phones IVHS-01 (accessory).  
The sound then continues to be  
outputted over the IR headphones  
IVHS-01 (accessory).  
26  
OPERATION  
Light bulb specifications  
Changing the light bulb  
Diameter: 8 mm  
Detach the monitor from the ceiling  
plate (4 screws).  
Length: 28 mm  
Voltage: 12 V, 3 W  
Changing the battery in the  
remote control  
Push the button on the battery  
compartment J to the right (see A  
below).  
Pull the battery compartment J  
out of the remote control (see B  
below).  
Screws for securing the  
ceiling-mounted monitor  
Change the 3 V battery (CR 2025).  
Remove the 3 screws of the metal  
cover (see picture below).  
Take out the old bulb.  
Fit a new bulb (12 V, 3 W).  
Refit the monitor.  
A
B
J
Metal cover  
Bulb  
27  
SPECIFICATIONS  
IVMR-9002  
Screen size:  
9" Monitor  
Screen resolution:  
Active area:  
1440 (H) x 234 (V)  
198.0 (H) x 111.74 (V)  
Dual system NTSC/PAL  
300 cd/m2  
Signal system:  
Brightness:  
Contrast ratio:  
Viewing angle:  
100  
Left/right: 65/65 degrees  
Up/down: 50/65 degrees  
Video input level:  
1.0 Vpp ± 10 %  
0.3 Vrms  
Audio input level:  
AUX input level:  
1.0 Vpp ± 10 %  
Carrier frequency for IR sensor:  
L-CH: 2.3 MHz  
R-CH: 2.8 MHz  
Operating voltage (direct current):  
Current consumption:  
Quiescent current consumption:  
Operating temperature:  
Storage temperature:  
Dimensions:  
10-16V  
1 A (at +12V)  
35 mA (at +12 V)  
0 - 60 °C  
- 30°C to +80°C  
286 x 258 x 57.4 mm  
2150 g  
Weight:  
Subject to changes!  
28  
SPECIFICATIONS  
IVMR-1042  
Screen size:  
10.4" Monitor  
Screen resolution:  
Active area:  
1920 (H) x 480 (V)  
211.2 (H) x 158.4 (V)  
Dual system NTSC/PAL  
290 cd/m2  
Signal system:  
Brightness:  
Contrast ratio:  
Viewing angle:  
100  
Left/right: 60/60 degrees  
Up/down: 40/50 degrees  
Video input level:  
1.0 Vpp ± 10 %  
0.3 Vrms  
Audio input level:  
AUX input level:  
1.0 Vpp ± 10 %  
Carrier frequency for IR sensor:  
L-CH: 2.3 MHz  
R-CH: 2.8 MHz  
Operating voltage (direct current):  
Current consumption:  
Quiescent current consumption:  
Operating temperature:  
Storage temperature:  
Dimensions:  
10-16V  
1.1 A (at +12 V)  
70 mA (at +12 V)  
0 - 60 °C  
- 30°C to +80°C  
322 x 305 x 63.5 mm  
2450 g  
Weight:  
Subject to changes!  
29  
Service-Nummern / Service numbers / Numéros du service après-  
vente / Numeri del servizio di assistenza / Servicenummers /  
Telefonnummer för service / Números de servicio / Números de  
serviço / Servicenumre  
Country:  
Phone:  
Fax:  
WWW:  
Germany  
(D)  
0180-5000225  
05121-49 4002  
Austria  
(A)  
(B)  
01-610 390  
02-525 5454  
01-610 393 91  
02-525 5263  
44-898 644  
09-435 99236  
01-4010 7320  
01-89583 8394  
210 57 69 473  
01-4598830  
02-369 6464  
40 2085  
023-565 6331  
66-817 157  
01-2185 11111  
916-467952  
08-7501810  
01-8471650  
Belgium  
Denmark  
Finland  
France  
(DK) 44 898 360  
(FIN) 09-435 991  
(F)  
01-4010 7007  
Great Britain (GB) 01-89583 8880  
Greece  
Ireland  
Italy  
Luxembourg (L)  
Netherlands (NL)  
Norway  
Portugal  
Spain  
(GR) 210 57 85 350  
(IRL) 01-4149400  
(I)  
02-369 6331  
40 4078  
023-565 6348  
66-817 000  
01-2185 00144  
902-120234  
08-7501500  
(N)  
(P)  
(E)  
(S)  
Sweden  
Switzerland (CH) 01-8471644  
Czech. Rep. (CZ)  
02-6130 0441  
01-333 9575  
0800-118922  
02-6130 0514  
01-324 8756  
022-8771260  
Hungary  
(H)  
Poland  
(PL)  
Turkey  
USA  
(TR)  
0212-3350677  
0212-3460040  
708-6817188  
(USA) 800-2662528  
Brasil  
(Mercosur)  
(BR) +55-19 3745 2769 +55-19 3745 2773  
Malaysia  
(Asia Pacific) (MAL) +604-6382 474  
+604-6413 640  
Blaupunkt GmbH  
01/04  
CM/PSS2 - 8 622 403 936  

Aiwa ICT X40B User Manual
Alpine CDA 7940 User Manual
AVE VSI PRO User Manual
Clarion OHM875VD User Manual
DB Drive K1 10D4 User Manual
Fishman Blender User Manual
GoPro Black CHDBX401 User Manual
Hitachi DZMV780MA User Manual
JBL GTO6537 User Manual
JVC Car Stereo System KD R538 User Manual