Black Box Camera Accessories CCTVTEST User Manual

June 2010  
CCTVTEST  
CCTV Tester  
Tests camera video output, signal strength, and  
PTZ functions. Also acts as a video pattern  
generator, cable mapper, and multimeter.  
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.  
call 724-746-5500) • FREE technical support 24 hours a day, 7 days a  
week: Call 724-746-5500 or fax 724-746-0746 • Mailing address:  
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
Customer  
Support  
Information  
NOM Statement  
2. Las instrucciones de seguridad y operación deberán ser guardadas para  
referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de  
operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca  
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que  
sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea  
recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a  
lo descrito en las instrucciones de operación. Todo otro servicio deberá ser  
referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no  
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,  
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar  
en libreros o gabinetes que impidan el flujo de aire por los orificios de  
ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor  
como radiadores, registros de calor, estufas u otros aparatos (incluyendo  
amplificadores) que producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del  
tipo descrito en el instructivo de operación, o como se indique en el aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización  
del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no  
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,  
poniendo particular atención a los contactos y receptáculos donde salen del  
aparato.  
724-746-5500  
|
blackbox.com  
Page 3  
CCTV Tester  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las  
recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas  
de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea  
usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean  
derramados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su  
desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
724-746-5500  
|
blackbox.com  
Page 4  
Trademarks Used in this Manual  
Trademarks Used in this Manual  
Black Box and the Double Diamond logo are registered trademarks of  
BB Technologies, Inc.  
Any other trademarks mentioned in this manual are acknowledged to be the  
property of the trademark owners.  
724-746-5500  
|
blackbox.com  
Page 5  
CCTV Tester  
Safety Information  
Precautions when using the CCTV Tester  
A. Please read this manual before using the product.  
B. Always be cautious when working around voltage.  
C. Do not use the tester in damp or explosive environments.  
D. Areas of strong electromagnetism can cause incorrect measurements.  
E. Do not expose the tester to dirt or liquid.  
F. Do not disassemble the tester.  
G. Operating environment:  
Temperature: -22 to 158° F (-30 to +70° C)  
Relative humidity: 30 to 90%  
Recharging voltage:5 VDC  
Precautions when charging the battery  
A. Use only the original, chargeable battery that came with the tester. When  
charging, use the original power adapter.  
B. Make sure the batteries are installed correctly (polarity).  
C. Do not short-circuit or disassemble batteries.  
724-746-5500  
|
blackbox.com  
Page 6  
Table of Contents  
Table of Contents  
1.  
Specifications .......................................................................................... 8  
........................................................................................ 10  
2. Overview  
2.1 Introduction .................................................................................. 10  
2.2 Features ........................................................................................ 10  
2.3 What’s Included.............................................................................11  
2.4 Hardware Description ....................................................................11  
3. Operation  
........................................................................................ 14  
3.1 Power and Battery ........................................................................ 14  
3.2 Main Menu Introduction............................................................... 14  
3.3 Quick Test...................................................................................... 15  
3.4 Main Menu.................................................................................... 15  
3.4.1  
System Setup................................................................... 15  
3.4.2 Video, Signal Strength, and PTZ Test.............................. 16  
3.4.3 UTP Cable Testing........................................................... 18  
3.4.4 Video Generator ............................................................. 19  
3.4.5 RS-485 Data Test............................................................ 20  
3.4.6 Multimeter ...................................................................... 22  
3.5 Provide Power to a 12V Camera................................................... 23  
3.6 Screen Brightness Adjustment...................................................... 23  
724-746-5500  
|
blackbox.com  
Page 7  
CCTV Tester  
1. Specifications  
Table 1-1. CCTV Tester specifications.  
Feature  
Description  
Video testing  
Signal mode  
LCD display  
NTSC/PAL compatible  
2.5" LCD screen, 960 x 240 resolution  
Max. Vpp, ave. Vpp, and Sync V  
1 channel BNC  
Signal strength  
Video input  
Video output  
LCD brightness  
1 channel BNC  
Adjustable from keypad  
PTZ test and  
control  
Communication  
protocol  
RS-232, RS-422 simplex and RS-485  
Includes 20 manufacturer’s protocols  
Baud rate  
2400, 4800, 9600, 19200  
Built-in  
multimeter  
DC voltage test  
AC voltage test  
Max.: 1000 V, Precision: 0.1 mV  
Max: 750 V, Precision: 0.1 mV  
Resistance test  
Max.: 40 Mohm, Precision: 0.1 ohm  
12 VDC  
Power to camera Voltage  
Working time  
4-5 hours to normal camera  
200 mA  
Max. current  
UTP cable test  
Signal generator  
RS-485 data test  
OSD menu  
Other functions  
Test UTP (CAT5/6) cables  
Test security monitors  
Display RS-485 data from device  
English OSD menu  
Keypad  
Easy to operate. Uses number buttons.  
5 VDC  
Power and battery Power adapter  
Battery  
3000 mAh rechargeable battery inside  
6 hours recharging time  
Sleep mode. Power status display.  
10 hours  
Rechargeable  
Low consumption  
Operating time  
724-746-5500  
|
blackbox.com  
Page 8  
Chapter 1: Specifications  
Table 1-1 (Continued). CCTV Tester specifications.  
Feature  
Work temperature  
Description  
Other  
-22 to +158° F (-30 to +70° C)  
30 to 90%  
Work humidity  
Size  
6.5"H x 3.6"W x 1.9"D  
(16.6 x 9.1 x 4.8 cm)  
Weight  
0.6 lb. (0.3 kg)  
724-746-5500  
|
blackbox.com  
Page 9  
CCTV Tester  
2. Overview  
2.1 Introduction  
The CCTV Tester tests camera video output, signal strength, and PTZ functions. It  
also acts as a video pattern generator, cable mapper, and digital multimeter.  
2.2 Features  
A. Camera video testing (Visual). See page 16. Test a CCTV camera’s video  
output visually by displaying it on the tester’s color LCD screen or loop the signal  
through to a video monitor.  
B. Camera video testing (Signal strength). See page 17. Perform a signal  
attenuation test with the touch of a button. The video signal’s voltage (max and  
average Vpp) is displayed as sync voltage. Perfect for detecting weak signals. Also  
measures sync voltage.  
C. Camera motion testing (PTZ). See page 17. Test a PTZ camera’s pan, tilt, and  
zoom directly from the tester’s keypad. Complete with preset settings and speed  
adjustment. Supports RS-232, RS-422 simplex and RS-485 connections. Baud  
rates of 2400, 4800, 9600 and 19,200. RS-485 protocol includes: Pelco D,P,  
Samsung, Panasonic, Molynx, and more.  
D. Monitor testing (Video signal generator). See page 15. Inspect monitors and  
DVRs by driving them with a known good video signal from the tester. It can  
output color bars and separate colors. The Camera Wizard only supports NTSC  
format.  
E. Keyboard testing (RS-485 serial data test). See page 20. Test the RS-485 data  
sent from a control device by displaying its hexadecimal data.  
F. Digital multimeter. See page 22. Detect AC/DC voltages and measure  
resistance using a built-in DMM. Useful in measuring and isolating circuit  
problems.  
G. Power to camera. See page 23. The tester can supply 12 VDC (200 mA) power  
to a CCTV camera. Use when no camera power supply is available.  
H. UTP (CAT5 or CAT6) cable test. See page 18. Test CAT5 or 6 cables for opens  
and shorts. Remote terminator included.  
724-746-5500  
|
blackbox.com  
Page 10  
Chapter 2: Overview  
2.3 What’s Included  
Your package should include the following items. If anything is missing or damaged,  
contact Black Box Technical Support art 724-746-5500 or [email protected].  
• CCTV Tester with rechargeable battery  
• Charger  
• UTP cable terminator  
• BNC connect cable  
• BNC to RCA adapter  
• PTZ terminal block/alligator adapter  
• DMM test leads  
• Lanyard  
• 12-VDC power cable  
• This user’s manual  
2.4 Hardware Description  
Figures 2-1 through 2-4 illustrate the CCTV Tester and describe its components.  
724-746-5500  
|
blackbox.com  
Page 11  
CCTV Tester  
Data transmit  
Data receive (PTZ  
(PTZ data): Lights data): Lights when  
when transmitting receiving data  
data  
Charge LED: when  
on, tester is charging  
Power: Lights  
when power is on  
Open: Open  
camera iris (PTZ  
test); Set: A mul-  
tipurpose button  
used to start or  
enable functions  
2.5" LCD screen:  
960 x 240 resolution  
Close/Clear: Close  
camera and clear  
setup (PTZ test)  
Tele: Zooms IN lens  
(PTZ test); switches  
generated video to  
Video Out jack (Video  
Generator test)  
Menu: Hold to  
return to the Main  
Menu  
Max. Vpp, Average  
Vpp, and sync signal:  
Press during video test  
for quick, accurate  
signal analysis  
Wide: Zooms Out  
lens (PTZ test); switch-  
es generated video to  
tester display (Video  
Generator test)  
Arrow keys: Move cam-  
era up, down, right, left  
(PTZ test). Also menu  
cursor control  
Far: Focus lens to far  
(PTZ test)  
Near: Focus lens to  
near (PTZ test)  
0–9 number keys:  
Input numbers for  
PTZ function  
P=PST (Call Preset):  
Recall stored PTZ position  
(PTZ test)  
S-PST (Setup Preset):  
Setup a preset PTZ  
position (PTZ test)  
ADDR (address): Set up  
a PTZ ID (PTZ test  
Figure 2-1. Faceplate.  
724-746-5500  
|
blackbox.com  
Page 12  
Chapter 2: Overview  
12 VDC power output  
jack: to power camera  
RS-232 port  
Figure 2-2. Side 1 view.  
CAT5/6 UTP  
Power on/off  
cable test jack  
5-VDC power input jack:  
Connect charger here  
Figure 2-3. Side 2 view.  
Video output:  
connect monitor here  
Video input:  
connect camera here  
RS-422/RS-485 port:  
Connect PTZ to +T and  
-T; Connect keyboard  
to +R and -R  
Figure 2-4. Top view.  
724-746-5500  
|
blackbox.com  
Page 13  
CCTV Tester  
3. Operation  
3.1 Power and Battery  
POWER: The power ON/OFF switch is located on the side of the tester.  
BATTERY SAVER: The tester has a battery-saving sleep mode. Turn the slide switch  
ON again if the tester is asleep.  
RECHARGEABLE BATTERY: The tester has a non-removable battery for a larger  
capacity. Do not open the rear panel and attempt to repair it.  
CHARGE TIME: The battery requires five hours for a full charge.  
CHARGE LED: While charging, the “Charge” LED will be ON.  
OPERATING TIME: Approximately 10 hours.  
WHEN TO RECHARGE: Recharge when the battery indicator in the System Setup  
menu shows 25% or less.  
USE WHILE CHARGING: The tester can be used during charging.  
3.2 Main Menu Introduction  
Turn on the device. The Main Menu appears: #1 is the setup mode. #2 thru #6  
selects five test modes. Use the keypads numbered buttons to select the menu  
item. The last item is the software version and serial number.  
MAIN MENU  
1 SYSTEM SETUP  
> Set up PTZ and check battery  
> Test video and control PTZ  
> Test UTP cables  
2 VIDEO AND PTZ TEST  
3 UTP CABLE TEST  
4 VIDEO GENERATOR  
5 RS485 DATA TEST  
6 MULTIMETER  
> Test video monitors  
> Analyze RS-485 protocol  
> Measure voltage/resistance  
> Software version and S/N  
VER:V1.11 S/N:08110910  
Figure 3-1. Main Menu.  
724-746-5500  
|
blackbox.com  
Page 14  
Chapter 3: Operation  
3.3 Quick Test  
A
B
Figure 3-2. Quick test setup.  
A. Viewing a camera image: Follow diagram A to connect a CCTV camera (includ-  
ing PTZ control) to the tester. The cameras video output connects to the testers  
VIDEO IN BNC connector. The cameras PTZ control wires connect to testers  
RS-485/422 control block (using the terminal block/alligator clip adapter provided  
with the tester). Turn ON the tester and select menu item “2.” The cameras video  
will display on the tester screen. More detailed instructions follow in this manual.  
B. Connecting a monitor: Follow diagram B to connect a CCTV monitor to the  
tester. The testers VIDEO OUT BNC connects to the monitors video input connector.  
You can drive the monitor with the video signal generated by the tester (menu item  
#4, then TELE) or in “looped mode” with a cameras video connected to the testers  
VIDEO IN BNC (menu item #4, then WIDE). More detailed instructions follow in this  
manual.  
3.4 Main Menu (in order of appearance)  
3.4.1 Selection 1: System Setup: Display battery status, set auto-off time, and set  
up PTZ parameters to match your CCTV camera.  
NOTE: If you are not using the PTZ (pan/tilt/zoom) test feature, there is no need to  
set the PTZ parameters.  
ENTERING AND EXITING: Press “1” to enter the setup screen. Press “MENU” to  
return to the Main Menu. A typical configuration is as shown in Figure 3-3.  
724-746-5500  
|
blackbox.com  
Page 15  
CCTV Tester  
PROTOCOL Pelco P  
> PTZ protocol of camera  
COM 485  
RATE 4800  
SPEED 016  
> PTZ communication port type  
> PTZ baud rate: 2400/4800/9600/19200  
> PTZ pan and tilt speed  
IDLE TIME 000  
BATTERY 090  
> Battery saver turn off time (minutes)  
> Battery status (%):100/90/75/50/25/5  
Figure 3-3. Typical configuration.  
MODIFYING THE SETTINGS:  
ENTER SETUP MODE: Press “SET.” In this mode you 1) modify the PTZ settings  
(Protocol, Com, Rate and Speed) to match the camera you are testing and 2) set the  
battery saver turnoff time (when no activity).  
SELECT THE ITEM: Press the “UP and DOWN arrows” to blink the line you wish to  
modify. Battery status (% remaining) cannot be modified.  
ADJUST THE PARAMETER: Press the “UP/DOWN/RIGHT arrow.”  
SAVE/EXIT. Press the “LEFT arrow” to save the setting. Press the “LEFT arrow”  
again to stop the blinking. Exit by holding the “MENU key” to return to the Main  
Menu.  
NOTE: The CCTVTEST has 20 PTZ protocols and 17 speed settings (1 is the slowest  
and 16 is the fastest).  
3.4.2 Selection 2: Video, Signal Strength, and PTZ Test  
A. Display a camera’s video signal on the LCD and monitor:  
CONNECTION: Connect the camera to the tester as shown in Figure 3-1. The  
camera connects to the testers VIDEO IN jack.  
Display camera video: Press “2” on the keypad to turn ON the testers video and PTZ  
feature. The cameras video appears on the color LCD display. The cameras video  
will also appear on a monitor (if connected to the testers VIDEO OUT jack). Study  
the image for proper focus and viewing angle. Study the voltage readout (below)  
for proper amplitude. And use the testers PTZ feature (below) to control pan, tilt,  
and zoom.  
724-746-5500  
|
blackbox.com  
Page 16  
Chapter 3: Operation  
Adjust LCD brightness: Use keys number 7 (BR+) and 9 (BR-) to adjust the LCD  
screens brightness.  
B. Measure signal strength (Vpp) and attenuation:  
Video signal strength (attenuation): With the tester displaying the video signal  
(see A), press the “1” (IRE) key. The following is displayed:  
MAX Vpp: The peak-to-peak amplitude of the video signal. The larger the video  
signal, the brighter the picture. 1 Vpp is minimum.  
AVERAGE Vpp: The average peak-to-peak amplitude of the video signal.  
SYNC SIGNAL: A cameras sync pulses synchronize the camera with the monitor.  
NO VIDEO: No signal, “No Video” will be displayed.  
Example of attenuation: If the Vpp at the camera is 1.25 Vpp, and the Vpp at the  
end of the cable is 1.15 V, the attenuation is 8%.  
C. Testing and controlling the camera motion (PTZ):  
Connection. Connect the camera to the tester as shown in Figure 3-2, diagram A.  
The cameras PTZ wires plug into the T+ and T- ports on the testers RS-422/485 jack  
(use the terminal block/alligator adapter).  
ADDRESS:001  
VIDEO: NULL  
> Enter the PTZ cameras ID (001–255)  
> Video format PAL/NTSC/NULL  
Enter the camera’s ID.  
Press “ADDR” and input the PTZ cameras ID.  
Press “SET” to save the address.  
Press “MENU” to hide the menu display.  
Hold “MENU” to exit the video/PTZ function and return to the Main Menu.  
724-746-5500  
|
blackbox.com  
Page 17  
CCTV Tester  
NOTE: See Section 3.4.1, System Setup to match the testers PTZ protocol, com type,  
and baud rate to that of the camera.  
Controlling the camera’s PTZ (pan/tilt/zoom):  
Press “UP/DOWN/LEFT/RIGHT” to control the movement.  
Press “OPEN/CLOSE” to control the iris.  
Press “FAR/NEAR” to adjust focus.  
Press “WIDE/TELE” to zoom the camera lens in and out.  
Saving and Calling Preset positions:  
The Video Wizard can Save and Call preset positions.  
To Save: Press “S-PST” and input a position number. Press “SET” to save.  
To Call: Press “C-PST” and input the position number. Press “SET” to call.  
Multiple preset positions can be saved.  
3.4.3 Selection 3: UTP Cable Testing: Testing a UTP cable (CAT5/6) for proper  
connection.  
NOTE: “UTP” means unshielded twisted pair. UTP is the most common type  
of CAT5 and 6 cable.  
CONNECTION: Connect the CAT5/6 UTP cable to the UTP TEST socket on the right  
side of the tester. Connect the Remote Terminator to the far end of the cable.  
Testing a CAT5  
or CAT6 cable  
(UTP)  
Remote  
terminator  
Figure 3-4. Testing UTP cable setup.  
724-746-5500  
|
blackbox.com  
Page 18  
Chapter 3: Operation  
SELECT UTP CABLE TEST MODE: Press the “3” key to enter the UTP test mode.  
START TEST: Press “SET.” The CAT5/6 UTP cable wire map will be displayed on the  
LCD screen.  
RETURN TO MAIN MENU: Hold the MENU key to return to the Main Menu.  
UTP CABLE TEST  
TESTER SIDE  
PIN NUMBERS  
1
2
3
4
5
6
7
8
----------------------  
----------------------  
----------------------  
----------------------  
----------------------  
----------------------  
----------------------  
----------------------  
1
2
3
0
0
6
7
8
REMOTE  
PIN NUMBERS  
Typical CAT5/6  
Cable (UTP)  
Wiremap  
”0” means open  
Two “0”s is a  
short circuit  
Figure 3-5. UTP cable test wiremap.  
3.4.4 Selection 4: Video Generator: Testing a monitor using the VIDEO OUT port.  
Connection. Connect the monitor to the tester using the VIDEO OUT jack:  
Without camera  
With camera  
Figure 3-6. Video generator test setup.  
Drive the monitor with the tester’s video generator. Or drive the monitor  
with a camera “looped” through the tester.  
SELECT VIDEO GENERATOR MODE: Press the “4” key to turn ON the video  
generator.  
724-746-5500  
|
blackbox.com  
Page 19  
CCTV Tester  
SELECT OPTIONS: Use the following keys to control the options:  
• SET selects the testers video signal: Color bar, Blue, Red, Pink, Green, Cyan,  
Yellow, and White.  
• TELE switches the testers video signal to the monitor (connected to the VIDEO  
OUT jack).  
• WIDE switches the video signal so it loops from the VIDEO IN jack to the VIDEO  
OUT jack. In this mode, a picture will only appear on the monitor if a camera is  
connected to the VIDEO IN jack.  
RETURN TO MAIN MENU: Hold the Main Menu key to turn OFF the video genera-  
tor and return to the Main Menu.  
Figure 3-7. Video generator (press SET to select and TELE to output).  
3.4.5 Selection 5: RS-485 Data Test: Analyze data from an RS-485 device (key-  
board).  
CONNECTION. Connect the device to the tester using the +R -R sockets (use  
terminal block/alligator adapter).  
724-746-5500  
|
blackbox.com  
Page 20  
Chapter 3: Operation  
Figure 3-8. RS-485 keyboard test setup.  
Display the device’s hexadecimal output on the tester’s LCD.  
SELECT THE DATA TEST MODE: Press the “5” key to turn ON the RS-485 protocol  
analyzer.  
SELECT OPTIONS: Use the following keys to control the options:  
• SET enables the changing of the Baud rate.  
• UP/DOWN ARROW KEYS change the testers Baud rate. Select the Baud rate that  
matches the device that is being analyzed.  
Data transfer will start automatically through the RS-485 port. The hexadecimal data  
is displayed on the testers screen as shown below. Analysis of the data will indicate  
its protocol.  
RETURN TO MAIN MENU: Hold the Main Menu key to turn OFF the data  
flow and return to the Main Menu.  
A0 00 01 00 00 00 AF 0F  
A0 00 01 00 00 00 AF 0E  
A0 00 01 00 00 00 AF 0F  
A0 00 01 00 00 00 AF 4F  
A0 00 01 00 00 00 AF EF  
A0 00 01 00 00 00 AF 2F  
Figure 3-9. Typical hexadecimal data from an RS-485 device.  
724-746-5500  
|
blackbox.com  
Page 21  
CCTV Tester  
3.4.6 Selection 6: Multimeter. Use the tester as a digital multimeter to measure  
AC/DC voltage and resistance.  
NOTE: The tester displays the Vpp of the video signal and sync signal on the LCD  
without the use of the test leads. See Menu Item #4 on page 14.  
CONNECTION: Connect the 2 test leads to the bottom of the tester as shown in  
Figure 3-10.  
Figure 3-10. DMM test leads attached to bottom of tester.  
SELECT MULTIMETER MODE: Press “6” on the keypad to turn ON the DMM  
(digital multimeter).  
DC: 121.3 MV  
1 DC VOLTAGE  
2 AC VOLTAGE  
3 RESISTANCE  
Figure 3-11. Digital multimeter menu.  
SELECT FUNCTION: Press key 1, 2 or 3.  
DC voltage test range: 0-1000 V, precision: 0.1 mV  
AC voltage test range: 750 V, precision: 0.1 mV  
Resistance test range: 0-40 Mohm , precision: 0.1 ohm  
RETURN TO MAIN MENU: Hold the Main Menu key to return to the Main Menu.  
NOTE: Exercise caution when voltage is present. If you are not familiar with  
proper safety techniques, ask for guidance. Do not exceed the testing  
range (above) or damage may occur.  
724-746-5500  
|
blackbox.com  
Page 22  
Chapter 3: Operation  
3.5 Provide Power to a 12V Camera  
The tester can be used to provide power to a 12V camera.  
CONNECTION: Connect the cable (included) to the testers DC 12V OUTPUT”  
jack (on the left side of the tester). Connect the other end to the cameras 12-VDC  
power input jack. Use only with 12 VDC cameras (200 ma max.).  
WORKING TIME: The amount of time that the tester powers the camera depends  
on the cameras power consumption. If the camera draws less than 100 mA, the  
tester will power the camera for about four hours.  
MAXIMUM CURRENT/POWER: The maximum output current from the tester  
is 200 mA/2400 milliwatts.  
NOTES:  
1. The output voltage of tester is DC12V. Please only connect it to 12V cameras.  
2. Do not connect the testers DC12V output to the testers own 5-VDC input jack.  
This will damage the tester.  
Power connected  
to camera  
Figure 3-12. Powering a 12 V camera.  
3.6 Screen Brightness Adjustment  
When in the Video and PTZ testing mode (menu item #2) use key number 7 (BR+)  
and key number 9 (BR-) to adjust the screens brightness.  
724-746-5500  
|
blackbox.com  
Page 23  
Black Box Tech Support: FREE! Live. 24/7.  
Tech support the  
way it should be.  
Great tech support is just 20 seconds away  
at 724-746-5500 or blackbox.com.  
About Black Box  
Black Box Network Services is your source for more than 118,000 networking  
and infrastructure products. You’ll find everything from cabinets and racks and  
power and surge protection products to media converters and Ethernet switches  
all supported by free, live 24/7 Tech support available in 20 seconds or less.  
© Copyright 2010. All rights reserved.  

Boston Acoustics GT 40 User Manual
Canon 155 A User Manual
Casio QV 120 User Manual
Creative A320 User Manual
Crown Boiler CWD110 User Manual
Elo TouchSystems touch monitor User Manual
Flip Video 3250 00176 A User Manual
IDEAL INDUSTRIES MINI C28 User Manual
Infiniti Car Speaker 6 1 User Manual
InStep QE100A User Manual