OWNER'S MANUAL
TRACK/SKIP
EJECT
REL
N
NI
U
G
T
VOL
BAND
SEL
ACD-17
VOL
T/F
MUTE
ACD-17
AM/FM/MPXRADIO
WITH DETACHABLE FRONT PANEL,
COMPACTDISCPLAYER
AND QUARTZ CLOCK
128-6496
1 of 16
Released 9-19-02
INSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases,
a special installation kit will be required to mount the radio to the dashboard. These kits are available at
electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to
make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line at
1-800-645-4994.
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. RemovethefrontpanelfromtheunitbypressingtheRELeasebuttonatthetoprightcorner; thenslidethe mounting
sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Checkthedashboardopeningsizebyslidingthemountingsleeveintoit. Iftheopeningisnotlargeenough,carefully
cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening
or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve
fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the
sleeve is firmly secured to the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting
sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are
secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing
the wiring connections, turn the unit on to confirm operation (ignition switch must be “on”). If unit does not
operate, recheck all wiring until problem is corrected.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and
the spring clips lock it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using
the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either
above or below the radio using the screw provided. Bend the strap to position it as necessary.
CAUTION:The rear of the radio must be supported with the strap to prevent damage to the dashboard
from the weight of the radio or improper operation due to vibration.
7. Test radio operation by referring to the Operating Instructions.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with
the installation kit to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 above.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trim panel.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting
brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the
dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and
brackets as they will be used to mount the new radio.
2. Carefully unsnap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION: DONOTEXCEEDM5X6MMMAXIMUMSCREWSIZE.
LONGERSCREWSMAYTOUCHANDDAMAGECOMPONENTSINSIDETHECHASSIS.
4. Wire the new radio to the vehicle as per step 4 above.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
3
128-6496
3 of 16
TOLL-FREE INSTALLATION ASSISTANCE
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you
do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days
and hours shown (U.S.A. and Canada only).
TIME ZONE
DAY
PACIFIC
MOUNTAIN
CENTRAL
EASTERN
MON.-FRI.
SATURDAY
8:30AM - 7PM
9AM - 5PM
7:30AM - 6PM
8AM - 4PM
5:30AM - 4PM
6AM - 2PM
6:30AM - 5PM
7AM - 3PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
NUT (5MM)
PERFORATED STRAP
EXISTING DASH OPENING
FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE
NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF
MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
FASTEN THIS END TO SCREW
STUD ON REAR OF CHASSIS
BEND TOP
TABS UPWARD
SCREW
(5MM)
BEND BOTTOM
TABS DOWNWARD
RADIO
SCREW STUD
FASTEN THIS END TO SECURE
PART OF DASHBOARD.
DRILL HOLE IF NECESSARY.
REMOVALTOOLS
NOTE: PLASTIC FRAME MUST BE REMOVED (UNSNAP ON LEFT
AND RIGHT SIDES) TO USE REMOVAL TOOLS.
20° MAX.
CAUTION:
SIDE VIEW
OF
CHASSIS
FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS MUST BE
MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE THE UNIT IS
MOUNTED WITHIN THIS LIMITATION.
FRONT PANEL
ISO INSTALLATION
TYPICAL INSTALLATION
REMOVETHEPLASTICFRAMEFROMTHEFRONTOFTHECHAS-
SISBYCAREFULLYUNSNAPPINGIT.
MAXIMUM
SCREW SIZE
M5 x 6
MAXIMUM
SCREW SIZE
M5 x 6
UNSNAP ON LEFT AND
RIGHT SIDES
FACTORY MOUNTING
BRACKETS
PLASTIC FRAME
4
128-6496
4 of 16
3
RADIO WIRING
REFER TO PAGE 6 FOR SPEAKER WIRING
CONTAINS:
1- 15A FUSE
1- 0.5A FUSE
6
5
128-6496
5 of 16
SPEAKER WIRING
REFER TO PAGE 5
FOR RADIOWIRING
WARNING!
! NEVERCOMBINE(BRIDGE)OUTPUTSFORUSEWITH1SPEAKER.
! NEVERGROUNDNEGATIVESPEAKERLEADSTOCHASSISGROUND.
! FAILURETOWIREEXACTLYASSHOWNBELOWMAYCAUSEELECTRICALDAMAGETO
THERADIO.
RADIO
5
HELP!
1 -8 0 0 -6 4 5 -4 9 9 4
Monday-Friday
Saturday
8:30am-7:00pmEastern
9:00am-5:00pmEastern
6
128-6496
6 of 16
OPERATING INSTRUCTIONS
24
9
14
15
17
13
16
23
27
10
19
18
TRACK/SKIP
EJECT
REL
N
NI
U
G
T
VOL
SEL
BAND
ACD-17
25
26
VOL
T/F
MUTE
1
8, 22
12,20
3, 4, 5, 6, 7
11,21
2
1POWER(PWR)ON-OFFBUTTON
Press this button ( ) to turn the unit on and
described in
the bass, tre4ble, balance and fader levels as
,
5
,6,and
7
.
off when the ignition switch is on. When the unit
is off, the time of day is automatically displayed
on the Liquid Crystal Display (LCD) panel
unless the ignition switch is off. If the radio is
off when the ignition switch is turned off, the
POWER button must be pressed to turn on the
radio after the ignition switch is turned on. If the
ignition switch is turned off while the radio is
on, the radio will come on automatically when
3
SELECT(SEL)BUTTON
This button is used to select the audio func-
tion (volume, bass, treble, balance or fade) to
be adjusted using the VOL + and - buttons.
Pressing the Select button once will set the
unit for volume adjustment (VOL will appear
on the display panel, followed by the setting
number). Pressing the button additional times
will select bass adjustment (BAS on display
panel), treble adjustment (TRE), balance (BAL),
fader (FAd), and volume (VOL) again. The dis-
play will return to the normal indication 5
seconds after the last adjustment or when
another function is activated.
the ignition switch is again turned on.
2
VOLUMECONTROLBUTTONS
To increase the volume level, press the
VOL+ button.Thevolumewillincreaseandthe
level will be shown on the display panel from
a minimum of V 0 to a maximum of V 63. To
decrease the volume level, press the VOL -
button. The display will automatically return to
the normal indication 5 seconds after the last
volume adjustment or when another function
is activated. These buttons are also used
in conjunction with the SEL button to adjust
4
BASSCONTROL
To adjust the bass level, first select the Bass
mode by pressing the SEL button until the BAS
indicationappearsonthedisplaypanel.. Within
5 seconds of choosing the Bass mode, press
the VOL + or - buttons to adjust the bass
conditions; the unit should be left in the stereo
7
128-6496
7 of 16
response as desired. The bass level will be on the display panel. Within 5 seconds of
shown on the display panel from a mini- choosing the Fader mode, press the VOL + or
mum of B -7 to a maximum of B 7 (BAS 0 - buttons to adjust the front-rear speaker levels
as desired. The fader position will be shown on
the display panel from FAF 10 (full front) to
FAr 10 (full rear), with each change
accompanied by a beep tone. When the vol-
ume level between the front and rear speak-
ers is equal, FAd 0 will appear on the display
panel. The display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is acti-
represents flat response), with each change
accompanied by a beep tone. The display
will automatically return to the normal indication
5 seconds after the last adjustment or
when another function is activated.
5
TREBLECONTROL
To adjust the treble level, first select the Treble
mode by pressing the SEL button until the
TRE indication appears on the display vated.
panel. Within 5 seconds of choosing the
8
LOUDNESSCONTOUR(LOUD)
Treble mode, press the VOL + or - buttons
to adjust the treble response as desired. The
treble level will be shown on the display panel
from a minimum of TRE -7 to a maximum of
TRE 7 (TRE 0 represents flat response), with
each change accompanied by a beep tone. The
display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is
activated.
When listening to music at low volume levels,
this feature will boost the bass and treble ranges
to compensate for the characteristics of
human hearing. Momentarily press the
LOUD/RND button to activate this feature as
indicated by LOUD on the display panel.
Pressing the button again will de-activate
the function and LOUD will disappear from
the display.
9
AM/FMBANDSELECTOR
During radio play, each time the BAND button
select the Balance mode by pressing the SEL is pressed, the radio band changes. The
6
LEFT/RIGHTBALANCECONTROL
To adjust the left-right speaker balance, first
indications AM or FM will appear on the
display panel according to your selection.
During CD play, pressing this button will
change to radio operation without ejecting the
disc.
button until the BAL indication appears on the
display panel. Within 5 seconds of choosing
theBalance mode,presstheVOL +or -buttons
to adjust the audio balance between the right
channel or left channel speakers, respectively.
The balance position will be shown on the
display panel from BAL 10 (full left) to BAr 10
(full right), with each change accompanied by a
beep tone. When the volume level between the
left and right speakers is equal, BAL 0 willbe
shown on the display panel. The display will
automatically return to the normal indica-
tion5secondsafter thelast adjustment or when
another function is activated.
bl
MANUALTUNINGCONTROL
Turn this knob clockwise to tune upward in
frequency on the band in use, counter-clock-
wise to tune downward in frequency. The fre-
quency to which you are tuned will be shown in
digital form on the display panel. When tuning
in a station, always adjust the control so that
the correct broadcast frequency is shown on
the display and adjust the control so that you
are receiving a clear signal. If the radio is tuned
off-frequency, you could experience distorted
audio, noise and other reception problems.
7
FRONT/REARFADERCONTROL
To adjust the front-rear speaker balance,
first select the Fader mode by pressing the
SEL button until the FAd indication appears
8
128-6496
8 of 16
7
bm
FMMONO/INTRO(INT)SELECTBUTTON
bq
LIQUID CRYSTAL DISPLAY PANEL
FUNCTIONS
During FM radio operation, press this button to
selectmono orstereoreceptionofthebroadcast
signal. Under normal reception mode as
The Liquid Crystal Display (LCD) panel dis-
plays the frequency, time, and all activated func-
tions, including five bar graphs which provide a
visual representation of the audio signal power
level.
NOTE: It is a characteristic of LCD panels
that, if subjected to cold temperatures
for an extended period of time, they
may take longer to illuminate than
under normal conditions. In addition,
the visibility of the numbers on the
LCD may slightly decrease. The LCD
read-out will return to normal when the
temperature increases to a normal
range.
indicatedbytheST
icononthedisplaypanel
when tuned to an FM stereo signal. If the stereo
signal is too noisy for comfortable listening,
press the MONO/INT select button to switch to
monaural reception (the ST
disappear from the display panel). To return to
stereo reception mode, press the button again
icon will
so that the ST
indication reappears.
bn
LOCAL(LOC)/REPEAT(RPT)BUTTON
During radio operation, received signals are
usually in stereo mode as indicated by the
ST
icon; however, when the signals are
weak or intermittent, it may be worthwhile
activating the Local (LOC) mode by pressing
the LOC/RPT button (LOC appears on the
display). This mode favors access to local
stations whose signals are much stronger,
thereby improving radio reception. Press this
button again to terminate local receive mode;
LOC disappears from the display panel.
br
DISC SLOT
With the label surface facing up, fully insert a
compact disc into the slot until the load
mechanism engages; LOAdCd will appear,
followedimmediatelybyCdPand thefixeddisc
symbol (
). The symbol will then become
animated and play will begin from the first
TRACK (01) on the disc, accompanied by the
elapsed time of track play.
bo
AUDIO MUTE (MUTE)
This button is used to mute the volume from
the system. By pressing the button, a MUTE
indication will appear on the display panel and
the volume will be muted. Pressing the MUTE
button again, or pressing the Volume Control
buttons or Select (SEL) button will return the
volume level to the setting in use before the
Mute function was activated.
NOTE: This unit is designed for play of
standard 5" (12cm) Compact Discs
ONLY. Do not attempt to use 3"
(8cm) CD-Singles in this unit, either
with or without an adapter, as
damage to the player and/or disc
can occur. Such damage will not
be covered by the Warranty on this
product.
bp
MODE BUTTON
This button enables selection of either radio
or disc play. When a CD is loaded, pressing
this button will revert to radio operation; the
bs
CDPLAY/PAUSE(
)SELECTOR
/
During disc play, pressing this button will
temporarilystopplayofthedisc(thediscsymbol
disc icon (
) will still be displayed, indicating
a disc is still loaded in the unit. Pressing the
button again will return to disc play, but the
current track will start from the beginning.
(
) will flash on the display panel). Press the
button again to resume play of the disc from the
point at which it was stopped. Playback will
9
128-6496
9 of 16
continue until all tracks on the disc have been
played, after which playback will automatically
stop (unless the repeat mode had been
selected).
cn
RANDOM(RND)SELECT
During disc play, press and hold the LOUD/
RND button for 2 seconds to play the tracks on
the disc in a random or shuffled order (RND will
appear on the display panel). In Random Play
mode, pressing the Forward Track Select
bt
FORWARDTRACK/SKIP SELECTOR (
)
During disc play, this button is used to quickly
select or skip to the beginning of a particular
track in the forward direction. With each press
of the button, the next higher TRACK number
will be selected as shown on the display
panel.
button (
dom order instead of the normal progression.
Pressing the Backward Track Select button (
will also select tracks in random order. The
Random Play mode can be cancelled by
pressing the button again for 2 seconds (RND
indication will disappear from the display panel)
or by activating the Track Intro-Scan (INT) or
Repeat (RPT) function.
) will also select tracks in a ran-
)
bu
BACKWARD TRACK/SKIP SELECTOR
(
)
During disc play, this button is used to quickly
select the beginning of a particular track in the
backward direction. With each press of the
button, the next lower TRACK number will be
selected as shown on the display panel.
co DISC EJECT ( ) BUTTON
When pressed, disc play is stopped and the
disc is automatically ejected; will disappear
from the display panel and the unit will revert to
radio operation. If the disc is not removed from
the unit, it will automatically be reloaded within
10 seconds to prevent accidental disc damage.
cl
REPEATPLAYSELECTOR
Duringdiscplay,pressingtheLOC/RPTbutton
will select the track repeat play mode. RPT
appears on the display panel. Play of the
selected track will continue to repeat until the
TrackRepeat function iscanceled bypressing
thebuttonagainorbyactivatingtheIntro-Scan
(INT) or Random (RND) function so that the
RPT indication disappears.
The
icon will remain displayed to indicate a
disc is still loaded in the unit.
NOTE: Always remove the disc from the
unit when the disc player is not to be
used for an extended period of time
to prevent accidental disc
cm
INTRODUCTION (INT)SCANSELECT
damage and to preserve disc life.
During disc play, press the MONO/INT button
to sample or scan the introduction, or first 10
seconds,ofeachtrackonthedisc. INTappears
on the display, and each track is played in
order. By using this option, you can quickly
choose the track(s) on the disc that you prefer.
When the desired track is recognized, press
the MONO/INT button again to cancel the INT
mode, or activate the Repeat or Random
cp
TIME/FREQUENCY SELECTOR (T/F)
This unit can display either the clock time or
radio frequency/CD player functions. Ordinarily,
the radio frequency or CD player track indica-
tion is displayed, but the display can also show
the time when this button is pressed. The time
will then be displayed for approximately 5 sec-
onds after which it will return to the radio or CD
player function display.
function so that
display.
INT disappears from the
10
128-6496
10 of 16
following circumstances as it will erase the
time memory:
1. Upon initial installation after all wiring is
completed.
The correct time-of-day can also be set into the
unit by pressing the Time/Frequency Selector
button. This procedure is outlined later in these
operating instructions.
2. If there is a malfunction of any of the
switches on the unit, pressing the RE
SET button may clear the system and
cq
THEFT-DETERRENT LED
Located on the chassis behind the front panel, a
light-emitting diode (LED) will flash when the
panel is physically removed. The flashing
lightserves as a visual warning to the would-be
thief that the unit has been disabled by removal
of the front panel.
csreturn to normal operation.
PANELRELEASE(REL)BUTTON
This button ( ) is used to release the
mechanism that holds the front panel to the
chassis. To detach the front panel, press the
button so that the right side of the panel
releases outward. Grasp the panel at the right
side and disengage it from the left side of the
chassis. To re-attach the panel, engage the
left side onto the chassis; then gently press in
the right side until it clicks and locks into
place. place.
cr
RESETBUTTON
A Reset button is located on the front panel of the
unit in the extreme lower right corner. The Reset
function is provided to protect the microproces-
sor circuitryandshouldonlybeactivated under the
CD PLAYER ERROR CODES
If a problem should develop while operating the CD player, an error code (ER-1, ER-2, ER-3, etc.)
may appear on the display panel. This can indicate a number of problems with the unit, includ-
ing a mechanical error or an error in the microprocessor control of the player. If an error code
should appear, try ejecting and reloading the disc into the player. While the disc is out of the unit,
make sure it is clean, undamaged, and loaded correctly (label surface up). You may also try
activating the RESET button
If the suggested measures do not solve the problem, contact an approved warranty station near
you for further assistance.
cq
on the unit, but this will also erase the time memory.
SETTING THE CLOCK
1. Turn the vehicle ignition and radio on.
2. Press and hold the Time/Frequency button
display will begin to flash.
cp
for approximately 2 seconds; the time
3. Within 5 seconds of selecting the flashing display, press the VOL + button to adjust the
hours and the AM/PM indication to the desired setting.
4. Press the VOL - button to adjust the minutes to the desired time.
4. Five seconds after the last hour or minute adjustment is made, the time will be set in the
unit and normal operation will resume.
11
128-6496
11 of 16
SPECIFICATIONS
Size:
7" W
x
2" H x 6-1/8" D
178 mm x 50 mm x 155 mm
OperatingVoltage:
Fuse Ratings:
12voltsDC,negativeground
Constant (yellow) lead: 15 AMP.
Switched (red) lead: 0.5 AMP.
OutputPower:
140 watts maximum ( 35 watts x 4 channels)
Output Wiring:
OutputImpedance:
Floating-ground type designed for 4 speaker use.
Compatible with 4-8 ohm speakers.
TuningRange:
AM: 519 – 1,735 kHz.
FM: 87.3– 108.5 MHz.
Sensitivity:
AM: 20uv.
FM: 1.5uv.
FMStereoSeparation:
> 25 dB
CDFrequencyResponse: 20 – 20,000 Hz. ±1 dB
CDSignal/NoiseRatio:
CDChannelSeparation:
CDDistortion:
> 60 dB
> 60 dB
0.2%
*Specifications are subject to change without notice.
12
128-6496
12 of 16
CARE AND MAINTENANCE
The radio section of your new sound system does not require any maintenance. We
recommend that you keep this manual for reference on the many features found in this unit as
well as how to set the clock.
The compact disc player section also requires no routine maintenance, but proper
understanding of its use and handling will help you obtain maximum enjoyment of its
capabilities. The following points should be observed:
! When cleaning the interior of the vehicle, do not get water or cleaning fluids on the unit.
! The CD player is a precision instrument and will not operate properly in extreme heat or
cold. In case of such conditions, wait until the interior temperature of the vehicle reaches a
normal temperature before using the player.
! If the temperature inside the player gets too hot, a protective circuit will automatically stop
play of the disc. In this case, allow the unit to cool off before operating the player again.
! Never insert anything other than a 5" (12 cm) compact disc into the player as the
mechanism can be damaged by foreign objects.
! Do not attempt to use 3" (8 cm) CD-Single discs in this unit, either with or without an
adaptor, as damage to the player and/or disc may occur. Such damage will not be covered
by the Warranty on this product.
! When not using the disc player, always remove the compact disc. Do not leave an ejected
disc sitting in the disc slot as this can expose it to sunlight and other causes of damage.
! Do not attempt to open the unit chassis. There are no user serviceable parts or adjustments inside.
! When the vehicle warms up during cold weather or under damp conditions, moisture may
condense on the lens of the disc player. Should this occur, the player will not operate
properly until the moisture has evaporated.
! The unit is designed with a vibration dampening CD mechanism to minimize interruption
of disc play due to normal vibration in a moving vehicle. When driving on very rough roads,
however, occasional sound skips may occur. This will not scratch or damage the disc and
normal play will resume when the rough conditions cease.
HANDLINGCOMPACTDISCS
Dirt, dust, scratches, and warpage can cause skips in the playback and deterioration of sound
quality. Please follow these guidelines to take care of your compact discs:
! Use only compact discs with the mark
! Fingerprints, dust, and dirt should be carefully wiped off the disc’s playing surface (shiny side)
with a soft cloth. Wipe in a straight motion from the inside to the outside of the disc.
! Never use chemicals such as record sprays, household cleaners or thinner to clean
compact discs. Such chemicals can irreparably damage the disc’s surface.
! Discs should be kept in their storage cases when not in use.
! Do not expose discs to direct sunlight, high temperatures or high humidity for extended periods.
! Do not stick paper, tape, or labels on the disc surfaces nor write on them with any type of marker.
13
128-6496
13 of 16
12 MONTH LIMITED WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser
of this product that should this product or any part thereof, under normal use and
conditions, be proven defective in material or workmanship within 12 months from the
date of original purchase, such defect(s) will be repaired or replaced with new or
reconditioned product (at the Company's option) without charge for parts and repair
labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be
delivered withproofofwarrantycoverage(e.g.dated billofsale),specificationofdefect(s),
transportation prepaid, to the warranty center at the address shown below.
ThisWarrantydoesnotextendtotheeliminationofcarstaticormotornoise,tocorrection
of antenna problems, to costs incurred for installation, removal, or reinstallation of the
product,ordamagetotapes,compactdiscs,speakers,accessories,orvehicleelectrical
systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company,hassufferedorbeendamagedthroughalteration,improperinstallation,mishan-
dling, misuse, neglect, accident, or by removal or defacement of the factory serial
number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,
SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY
ACTION FOR BREACH OF ANY WARRANTYHEREUNDERINCLUDINGANYIMPLIED
WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE
COMPANYBELIABLEFORANYCONSEQUENTIALORINCIDENTALDAMAGESFOR
BREACHOFTHISORANYOTHERWARRANTY,EXPRESSORIMPLIED,WHATSO-
EVER. NopersonorrepresentativeisauthorizedtoassumefortheCompanyanyliability
other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations or
exclusions may not apply to you. This Warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
U.S.A.: AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 • 1-800-645-4994
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
FormNo.128-4270E
14
128-6496
14 of 16
THISPAGEINTENTIONALLYLEFTBLANK
15
128-6496
15 of 16
© 2002 Audiovox Electronics Corp., Hauppauge, NY 11788
Printed in China
1 6
128-6496
128-6496
16 of 16
|