Audiovox 50 0311x 015 Series User Manual

INSTALLATION INSTRUCTIONS  
FOR  
50-0311x-015 SERIES 1181337  
GRAND CARAVAN  
OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM  
These instructions are intended for use only by experienced professionals in the automotive  
customizing business. Special tools and equipment, as well as specialized handling and care  
of product during installation, may be required. Before beginning this installation, carefully read  
through the following instructions. Use extreme care when cutting headliner material.  
Check for wiring or other componentry above headliner material. Cut only where indicated.  
Materials/ Tools required for this installation:  
1. #2 Phillips screwdriver  
3. Awl or similar tool  
5. 18 GA wire 4' - 6'  
2. Powered screwdriver or drill with adapter  
4. Razor knife or similar  
6. Test light  
7. Audiovox Series 640/650 Video Module  
NOT FOR VEHICLES EQUIPPED WITH SUN ROOF.  
Nov. 8, 1999  
Printed in the U.S.A  
INSTALLATION INSTRUCTION # 44-0047A  
I. PREPARATION OF VEHICLE INTERIOR  
1. Remove and retain (3) three screws which secure  
dome light in place. See Figure 1.  
2. Disconnect wiring and lay light in a safe place.  
FIGURE 1  
3. Using O.E. console as a reference, carefully  
measure and trim headliner as shown. Caution:  
Before cutting headliner material, check for  
wiring or other componentry above headliner.  
Cut only where indicated. DO NOT OVERCUT  
HEADLINER. Make sure that the 7 1/2" cut is  
centered left to right in vehicle.  
See Figure 2.  
4. If speaker upgrade kit was purchased, trim these (*)  
locations. See Figure 2.  
FIGURE 2  
5. Construct a jumper harness that will connect the  
vehicle’s dome light wires to the lights in video  
system. Connect the white wire from video system  
to the O.E. pink/blue wire. Connect the black wire  
from video system to the chassis ground.  
See Figure 3.  
6. Using a test light, check function of lights.  
7. Install O.E. dome light in original manner.  
FIGURE 3  
3
8. Install and route all video and audio cables, and any  
other added component requirements to their  
respective places in the vehicle. Refer to component  
installation instructions for wiring diagrams. The  
suggested routing of the video system cable is as  
follows: Above the headliner from video system  
rearward to the C-pillar. Down the C-pillar to the  
floor. Route the power lead to a fused accessory  
controlled source. Connect the ground lead to the  
vehicle chassis. Route the remaining wiring (RCA  
plugs, Remote Sensor extension, etc.) to the VCP  
location. See Figure 4. Connect per instructions  
included with the video system. If video system if to  
be used as a television, install an appropriate antenna  
per instructions included with the antenna.  
FIGURE 4  
9. Install console mounting bracket (item 6 pg 2)  
over O.E. bracket on roof brace. Align bend in  
bracket with edge of O.E. brace. Secure bracket  
using (4) four # 8 x 9/16" screws (item 1 pg 2).  
See Figure 5.  
FIGURE 5  
II. INSTALLATION OF CONSOLE  
IF SPEAKER UPGRADE KIT WAS PURCHASED, INSTALL PER INSTRUCTIONS PROVIDED.  
10. Raise console (item 7 pg 2) into approximate  
position against headliner. Loosely install using (2)  
two 6-32 X 3/4" screws (item 2 pg 2) through the  
smaller holes in bracket on console into threaded  
clips on mounting bracket. See Fig. 6.  
11. Using a scribe or similar tool, align hole in rear of  
console with slot in mounting bracket. Loosely  
secure rear of console using (1) # 8 X 1 1/2" screw  
(item 4 pg 2). Make sure console is straight then  
tighten (2) two 6-32 screws previously installed.  
See Figure 6.  
FIGURE 6  
4
12. Release video screen from locked position. Lower  
video screen to viewing position for access to  
mounting locations in top of video system  
housing.  
13. Raise video system into approximate position and  
connect all wiring to components. Connect wiring  
and cabling to video system per instructions  
included with video system.  
14. Check function of all components and lights. See  
operating instructions for video system operations  
check. For further assistance, refer to the video  
system manual for the technical support phone  
number listed for your area.  
FIGURE 7  
15. Insert video system into opening in console. Note: Make sure wires do not get pinched between video  
system and console. Align holes in housing with clips in mounting bracket. Secure using (4) four 6-32 x  
3/4" screws (item 2 pg 2) and (4) four 3.5 mm washers (item 3 pg 2). See Figure 7.  
Caution: Do not overtighten screws.  
16. Tighten screw previously installed to secure rear of  
console to headliner. Caution: Do not overtighten  
screws or damage to vehicle roof may occur.  
17. Raise video screen into locked position.  
18. Install speaker grille (item 8 pg 2). Align clips in grille  
with holes in console and press firmly.  
See Figure 8.  
19. If speaker upgrade kit was not installed, install cover  
plate (item 9 pg 2) at front of console and secure  
using (2) two # 6 X 1/2" screws (item 5 pg 2 ).  
20. Install cover plate decal (item 10 pg ).  
FIGURE 8  
5

Barco Car Video System MFGD 3220 D User Manual
Blaupunkt ALICANTE CD30 User Manual
Blaupunkt Hollywood C30 User Manual
Bosch Appliances MUM 4750 UC User Manual
Bushnell Binoculars 18 1035 User Manual
Canon Camcorder Vixia HD Camcorder User Manual
Carson SA 441 83F User Manual
Cerwin Vega Car Speaker CVA 121 User Manual
Iluv i182 User Manual
Jensen PowerPlus 652C User Manual