Audiovox 27PL User Manual (1)

INSTALLATION INSTRUCTIONS  
FOR  
1187025 & 27PL  
2000+ SUBURBAN W/ SUNROOF  
OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM  
NOTE: Requires Additional Insert  
These instructions are intended for use only by experienced professionals in the automotive customizing  
business. Special tools and equipment, as well as specialized handling and care of product during installation,  
may be required. Before beginning this installation, carefully read through the following instructions. Use  
extreme care when cutting headliner material. Check for wiring or other components above headliner  
material. Cut only where indicated.  
Materials/ Tools required for this installation:  
1. #2 Phillips screwdriver  
3. Razor Knife or Similar  
5. 18 GA wire 9'  
2. Powered screwdriver or drill with adapter  
4. Digital Voltmeter  
6. Measuring Tape  
7. Masking Tape  
8. Audiovox Video Module & Plastic Insert  
PREPARATION OF VEHICLE INTERIOR  
1. Cut out the oval dome light cutout on the  
template (item 8 pg 2) with a scissors or knife.  
Remove dome light from the vehicle by  
unsnapping the lens and disconnecting the wires.  
Align template to the ceiling of the vehicle as  
indicated and tape to ceiling with ½” masking  
tape. Cut a hole in the headliner using the bold  
line marked “Cut This Line” on the template.  
NOTE: You may have to cut twice, once through  
the template and once through the headliner itself.  
Remove template. The rear edge of the hole in  
the headliner should be cut right up to the metal  
beam which is laminated to the under side of the  
headliner.  
2. Loosen headliner around the sunroof opening by pulling the  
gasket of the headliner out of the channel along the rear edge  
of the sunroof. Insert the mounting bracket (item 7 pg 2),  
positioning the rear tabs over the sunroof motor toward the  
rear of the vehicle. NOTE: The large hole at the front end of  
the bracket aligns with the emboss in the factory cross  
member.  
3. Install two (2) #10 x 3/8” screws (item 2 pg 2) into front of  
mounting bracket (item 7 pg 2) to secure bracket into place.  
4. Using a digital voltmeter, check function of lights.  
5. Construct a jumper harness that will connect the  
vehicle’s dome light wires to the lights in video system.  
Connect the purple/brown wire from video system to  
the O.E. black wire. Connect the black/red wire from  
video system to the O.E. orange wire. Connect the  
red/black wire from the video system to the O.E. white  
wire.  
3
6. Install and route all video and audio cables, and any other  
added component requirements to their respective places in  
the vehicle. Refer to component installation instructions for  
wiring diagrams. The suggested routing of the video system  
cable is as follows: Above the headliner from video system  
to the B-pillar. Down the B-pillar to the floor. Route the  
power lead to a fused accessory controlled source. Connect  
the ground lead to the vehicle chassis. Route the remaining  
wiring (RCA plugs, Remote Sensor extension, etc.) to the  
VCP location. See Figure 4. Connect per instructions  
included with the video system. If video system if to be used  
as a television, install an appropriate antenna per instructions  
included with the antenna.  
INSTALLATION OF CONSOLE  
7. Raise console (item 6 pg 2) into position against the headliner.  
Install 4 screws (item 1 pg 2) and 4 washers (item 3 pg 2) to  
secure console into place.  
8. Install appropriate plastic insert into recess in the main console.  
Release video screen from locked position. Lower video screen to  
viewing position for access to mounting locations in top of video  
system housing.  
9. Raise video system into approximate position and connect all wiring  
to components. Connect wiring and cabling to video system per  
instructions included with video system.  
10.Check function of all components and lights. See operating  
instructions for video system operations check. For further assistance,  
refer to the video system manual for the technical support phone  
number listed for your area.  
11.Insert video system into opening in console. Note: Make sure wires  
do not get pinched between video system and console. Align  
holes in housing with holes in mounting bracket. Secure using 4 screws  
(item 4 pg 2) and 4 washers (item 5 pg2).  
Caution: Do not over tightenscrews.  
7. Raise video screen into locked position.  
4

Audiovox Jensen Phase Linear UMP400 User Manual
Bushnell NIGHT WATCH 263230CL User Manual
Canon DC 320 User Manual
Canon LC 2 User Manual
Cuisinart CH 4 User Manual
Fujitsu CS81 User Manual
Hitachi VM 7400A User Manual
Hypertec Notebook Case N15958PHY User Manual
Imperial Range 48BR User Manual
JBL Power P52c User Manual