Attwood 69371 User Manual

SKI TOW INSTALLATION INSTRUCTIONS  
®
NOTE: Before you drill or cut a hole in your boat, BE ABSOLUTELY  
CERTAIN there is room for the Ski Tow and the internal  
2-1/2" x 5" (64mm x 127mm) Backing Plate. See Figure 2.  
3
Stainless Steel Ski Tow  
Installation Instructions  
1. Carefully mark center of the hole.  
2. Use a 2-1/8" (54mm) hole saw to cut hole for the Ski Tow. See  
Figure 2.  
3. Separate fasteners and Backing Plate from the Ski Tow and set  
aside. Apply a small bead of marine sealant to the groove under  
the Ski Tow flange. Place Ski Tow in the hole cutout.  
66448 Series  
4. Align Ski Tow so the hook is vertical and the opening is up.  
SAVE THESE INSTRUCTIONS  
Form Number 69371 Rev. D  
5. From inside the transom, fit Backing Plate over the Ski Tow studs.  
Of the four holes, the two holes in the center will fit on the Ski Tow.  
06-05  
6. Attach fasteners to the Ski Tow studs. Tighten firmly, but do not  
damage transom or gelcoat by overtightening.  
This product carries a limited Lifetime Warranty.  
See www.attwoodmarine.com or Product Catalog for details.  
Figure 2  
APPLICATION  
This Attwood Ski Tow is intended for recreational water sport  
applications only.  
Locking Nuts  
Washers  
CAUTION  
Read all instructions carefully before installing and using this product.  
WARNING:  
The Ski Tow is not to be used for watercraft towing, lifting, or for any  
other anchoring application. Any misuse of the intended application  
will void the warranty and may result in personal injury and/or  
damage to the boat.  
Backing Plate  
2-1/8" (54mm.) Dia.  
To prevent injury, remove boat from water when installing this  
product and before using 120V power tools.  
REQUIRED FOR INSTALLATION  
• 9/16" deep-socket wrench  
Apply Marine Sealant  
• 2-1/8" (54mm) hole saw  
• Cordless drill  
ATTWOOD LIMITED LIFETIME WARRANTY  
• Polyurethane marine sealant  
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331  
(“Attwood”) warrants to the original consumer purchaser that, under normal  
use and service, this Attwood brand product will be free from defects in  
materials and workmanship for the service life of the vessel on which it is  
originally installed. This limited warranty is not applicable if the product has  
been damaged by accident, improper installation, unreasonable or improper  
use, lack of proper maintenance, unauthorized repairs or modifications,  
normal wear and tear, or other causes not arising out of defects in materials  
or workmanship. Attwood products are warranted for use on pleasure boats.  
Any other use - including but not limited to commercial, racing, or non-marine  
use - are not covered under this warranty. Attwood’s obligation under this  
warranty is limited to repair of the product at Attwood’s plant or replacement  
of the products at Attwood’s option without expense to the original consumer  
purchaser. Any expenses involved in the removal, reinstallation or transportation  
of the product are not covered by this warranty. The product must be  
returned to Attwood’s plant at the address above, postage prepaid, and  
insured with proof of original purchase including date. If Attwood is unable  
to replace the product and repair is not commercially practical or cannot be  
timely made, or if the original consumer purchaser is willing to accept a refund  
in lieu of repair or replacement, Attwood may refund the purchase price, less  
an amount for depreciation. The acceptance by Attwood of any product  
returned or any refund provided by Attwood shall not be deemed an  
admission that the product is defective or in violation of any warranty.  
Products that are replaced or for which a refund is issued become the  
property of Attwood.  
LOCATION  
Select an installation location that meets the following criteria:  
• Ski Tow should be centered on the transom, with the hook vertical  
and the opening pointing up to accept ski line. To avoid line slipping  
off the hook, fold it through the end loop to form a knot as shown  
in Figure 1.  
• Location on vessel must be able to withstand anticipated loads.  
• Transom must be a minimum of 3/4" (19mm) thick.  
• Interior space behind the Ski Tow must be large enough  
to accommodate the internal 2-1/2"x 5" (64mm x 127mm)  
Backing Plate.  
• Access to the interior of the transom is necessary to install the  
Backing Plate.  
Figure 1  
THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY OF THIS  
PRODUCT. ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES,  
FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER  
INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES.  
Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitations and exclusions may  
not apply to you. This warranty gives you specific legal rights, and you  
may have other rights which vary from state to state.  
© 2006 Attwood Corporation  
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com  

Alpine Electronics Car Video System IVA W202R User Manual
Alpine TMX R705 User Manual
Attwood 4202 User Manual
Bravetti KB305H User Manual
Cateye CC HB100 User Manual
Duracell CopperTop MN2400 User Manual
Focal Access 1 6 A3 User Manual
Hanns G Car Video System HSG 1083 User Manual
JL Audio 10W0v2 4 User Manual
JVC GR FX101 User Manual