Attwood 1492 User Manual

POLE HOLDER INSTALLATION INSTRUCTIONS  
®
NOTE: Before you drill or cut a hole on your boat, BE ABSOLUTELY  
CERTAIN there is room for the unit to fold in beneath the deck or  
gunwale where it will be installed. The Pole Holder, in the down  
position, will be recessed beneath the deck or gunwale.  
3
Push Pole Holder  
1. Use template provided to mark opening in deck (Figure 1).  
66346  
2. Cut opening using sabre saw. Place a bead of marine sealant  
around opening (Figure 2).  
Installation Instructions  
Attwood marine hardware, navigational lighting, bilge pumps, and  
other marine accessories are specified more than any other brand  
by America’s best-known boat manufacturers as original equipment.  
Look to Attwood for quality replacement parts and marine accessories.  
Figure 2  
SAVE THESE INSTRUCTIONS  
Form Number 69357 Rev. B  
03-10  
APPLICATION  
This holder will accommodate push poles up to 1-1/2" (3,8cm)  
in diameter.  
Installation requires three Attwood Push Pole Holders – the two  
outside holders facing one direction, the middle holder facing the  
opposite direction.  
NOTE: It is recommended that a boat builder, boat dealer, or a  
qualified marine mechanic perform the installation of the Attwood  
Pole Holder.  
REQUIRED FOR INSTALLATION  
• Cordless drill and bits  
• Sabre saw  
3. If installing Pole Holder only: Place Pole Holder into cutout and  
fasten with four #8 flat head self-tapping stainless steel screws.  
• Screwdriver  
• Marine sealant  
• Length of 3/8" (9,5mm) I.D. hose  
(for optional 1496-1 Drainage Receptacle)  
4. If installing with the optional Drainage Receptacle (1496-1): Use  
template provided and drill four 1/4" (6,4mm) holes where indicated.  
Place Pole Holder into cutout from above the deck. Hold Drainage  
Receptacle below deck and line up with holes of Pole Holder. Fasten  
together with four #8 stainless steel machine screws and nuts.  
WARNING:  
5. Connect 3/8" (9,5mm) I.D. hose to the fitting on the Drainage  
Receptacle, then route hose into bilge or to a drain fitting.  
To prevent personal injury, always remove the boat from the water  
before using any 120V AC power tools.  
ATTWOOD LIMITED WARRANTY  
LOCATION:  
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331 (“Attwood”)  
warrants to the original consumer purchaser that Attwood brand products will be  
free from defects in materials and workmanship under normal use and service for  
one year from the date of original consumer purchases.  
Select an installation location that meets the following criteria:  
• Each cutout location must be large enough (see Figure 1)  
and deep enough to accommodate the retracted Pole Holder.  
This limited warranty is not applicable if the product has been damaged by accident,  
improper installation, unreasonable or improper use, lack of proper maintenance,  
unauthorized repairs or modifications, normal wear and tear, or other causes not  
arising out of defects in materials or workmanship.  
• Access to the underside of the mounting surface is necessary  
to fasten the optional Drainage Receptacle (1496-1).  
Attwood products are warranted for use on pleasure boats. Any other use — including  
but not limited to commercial, racing, or non-marine use — are not covered under  
this warranty. Attwood’s obligation under this warranty is limited to repair of the  
product at Attwood’s plant or replacement of the products at Attwood’s option without  
expense to the original consumer purchaser. Any expenses involved in the removal,  
reinstallation or transportation of the product are not covered by this warranty.  
Figure 1  
3¹ꢀ₂"  
The product must be returned to Attwood’s plant at the address above, postage  
prepaid, and insured with proof of original purchase including date.  
If Attwood is unable to replace the product and repair is not commercially practical  
or cannot be timely made, or if the original consumer purchaser is willing to accept  
a refund in lieu of repair or replacement, Attwood may refund the purchase price,  
less an amount for depreciation. The acceptance by Attwood of any product returned  
or any refund provided by Attwood shall not be deemed an admission that the product  
is defective or in violation of any warranty. Products that are replaced or for which a  
refund is issued become the property of Attwood.  
1¹ꢀ₄"  
2¹ꢀ₁₆"  
THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY OF THIS  
PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1) YEAR  
FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. ATTWOOD SHALL  
NOT BE LIABLE FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT,  
NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS  
OR EXPENSES.  
Some states do not allow limitations on how long an implied warranty lasts or the  
exclusion or limitation of incidental or consequential damages, so the above  
limitations and exclusions may not apply to you. This warranty gives you specific  
legal rights, and you may have other rights which vary from state to state.  
2"  
© 2003 Attwood Corporation  
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com  

Adcom GFA 4302 User Manual
Alesis POWER AMPLIFIER RA500 User Manual
American Audio American DJ Supply, Inc Car Speaker DLS 15 User Manual
Canon DM XM1 User Manual
Dual Car Amplifier ALB10 User Manual
Focal Polyglass 33 V2 User Manual
Fostex FW187 User Manual
Hitachi VM H57A User Manual
Insignia NS C3112 User Manual
JVC 0797TOV_UN_SN User Manual