Aiwa CDC X927M YUC User Manual

OPERATING INSTRUCTIONS  
MANUAL DE INSTRUCCIONES  
MODE D’EMPLOI  
CDC-X927M  
YUC  
STEREO CAR CD RECEIVER  
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA  
AUTOMOVIL  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
OWNER’S RECORD  
For your convenience, record the model number and  
serial number (you will find them on the bottom side of  
your set) in the space provided below. Please refer to  
them when you contact your AIWA dealer in case of  
difficulty.  
Model No. CDC-X927M  
Serial No.  
8C-KC4-901-01  
020131ATM-OX  
Adjusting the volume  
THEFT PROTECTION  
(Retractable Front Panel)  
1
Turn AUDIO CONTROL.  
When your car’s ignition switch is turned off, the front  
panel will be retracted automatically as if there were no  
car audio in the console.  
When the ignition switch is set to ACC or ON position,  
the front panel will appear automatically.  
VOL (volume) indication appears.  
Muting the sound  
1
Press PWR/MUTE briefly.  
MUTE indicator flashes.  
To restore volume, briefly press PWR/MUTE again.  
Note  
Do not touch and put excessive pressure on the front  
panel while it is rotating.  
Adjusting sound  
You can select the following modes for adjusting sound  
depending on the music you listen to: BASS (low  
frequencies), TRE (high frequencies), BAL (left/right),  
FAD (front/rear), H-BASS (high bass)*, DSSA (Drivers  
Sound Stage Adjustment)** and BBE***.  
BASIC OPERATION,  
AUDIO AND CLOCK  
ADJUSTMENT  
*
You can reinforce the bass sound.  
** Youcanadjustsoundstageandtonebalancetobest  
serve a particular seat in the car.  
AUDIO CONTROL  
TUNE  
EJECT  
*** Youcanenhancetheclarityofhigh-frequencysound.  
1
Press SEL repeatedly to select the mode to be  
adjusted.  
Pressing SEL cycles through the modes. The  
selected mode’s indicator appears.  
Turn AUDIO CONTROL to increase or decrease  
the level for the selected mode (except for H-BASS,  
DSSA and BBE).  
SEL DISP  
PWR/MUTE BAND  
SRC  
2
InH-BASSmode, turnAUDIOCONTROL toselect  
1, 2, 3, or OFF.  
In DSSA mode, turn AUDIO CONTROL to select L  
(for the front left seat), R (for the front right seat), or  
OFF.  
Turning the unit on/off  
• You can turn the unit on by pressing any button on the  
front panel except z. The unit also turns on when you  
press z and insert a CD.  
• Press and hold PWR/MUTE until the unit turns off.  
In BBE mode, turn AUDIO CONTROL to select 1,  
2, or OFF.  
Note  
Notes  
Most operations described in this manual require  
theunittobeturnedonbeforestartingtheoperation,  
unless explicitly stated otherwise.  
• Adjust the level or select an item within 5 seconds, or  
the selected mode will return to previous state.  
• WhenDSSAisactivated,youcannotadjustBAL,FAD,  
BASS, TRE and BBE.  
• When BBE sound is activated, you cannot adjust  
BASS and TRE.  
Changing the source mode  
1
Press SRC.  
Pressing SRC cycles through source modes in the  
following order:  
Aligning the source levels  
(Source Level Adjuster)  
Volume may vary each time you change the source  
mode. In this case, you can align each source mode’s  
volume to almost the same level.  
*
To select another bands, press BAND to select F2,  
F3, A1, A2, while “F1” is displayed.  
1
2
PressSRCrepeatedlytoselectthedesiredmode.  
Press DISP while pressing SEL.  
** “DISC” does not appear on the display when there is  
no CD in the unit.  
***CD Changer Play mode (available when an optional  
CD Changer is connected)  
“LEVEL 0” appears on the display.  
3
Turn AUDIO CONTROL to adjust the level.  
Note  
Adjust the level within 5 seconds, or this function will be  
canceled.  
ENGLISH 2  
1
2
Press BAND repeatedly to select the desired band  
(F1, F2, F3, A1 or A2).  
Restoring the factory settings  
1
2
Turn off the unit.  
Press TUNEi (to move to higher frequencies) or  
TUNEk (to move to lower frequencies) to tune in to  
a station.  
PressandholdDISPuntilLEVEL--appearsonthe  
display.  
“ST” appears on the display when an FM station is  
broadcasting in stereo, and receiving conditions are  
good.  
Seek Tuning and Manual Tuning  
• Press and hold TUNEi or TUNEk until Seek  
Tuning starts.  
Note  
YoucanrestorethefactorysettingsonlyforVOL,BASS,  
TRE, BAL, FAD, H-BASS, DSSA and BBE as well as  
aligned source volume levels.  
The unit locates a station automatically (Seek  
Tuning).  
Setting the beep tone  
1
2
Turn off the unit.  
• Press  
iorTUNEkrepeatedlytosearchfor  
TUNE  
Press and hold SEL until “BEEP” appears on the  
display.  
a desired station while increasing or decreasing  
the frequency step by step (Manual Tuning).  
To stop Seek Tuning, press TUNEi or TUNEk  
again.  
3
4
TurnAUDIOCONTROLtoselectONorOFF”.  
Press SEL.  
The unit turns off.  
Monaural mode  
When FM signals become weak, or FM reception  
becomes poor, the unit automatically switches to  
Monaural mode to reduce noise.  
Setting the clock  
1
2
3
Press and hold DISP until the clock indicator  
flashes on the display.  
Note  
Press TUNEi (to set hour) or TUNEk (to set  
minute) and turn AUDIO CONTROL.  
Press DISP.  
When stereo sound is received, you can also press ST  
and select “MONO ON” to listen in manaural mode.  
To resume stereo sound receiving, press ST to “MONO  
OFF”.  
Displaying the clock  
Local mode  
Local mode allows you to tune in only to strong stations  
during Seek Tuning.  
1
Press DISP.  
To return to the former display, press DISP again.  
1
Press LO before you start seek tuning.  
“LO” appears on the display.  
To return to Distant mode, press LO again.  
“LO” disappears and the unit tunes in to all receivable  
stations.  
RADIO OPERATION  
Tuning in to a station  
(Seek/Manual Tuning)  
Using preset stations  
You must preset stations before you can tune in to a  
station using preset station number buttons.  
TUNE  
TUNE  
BAND  
ST LO SRC  
Stereo indicator  
Band indicator*  
BAND  
PS/A.ME SRC  
Preset station  
buttons 1 – 6  
Preset station number  
Local indicator  
Frequency indication  
* “F” means FM, and “A” means AM.  
3 ENGLISH  
Presetting stations automatically  
(Auto Memory)  
CD PLAYER OPERATION  
Playing a CD  
1
Press BAND repeatedly to select the desired band  
(F1, F2, F3, A1 or A2).  
You can play CDs, CD-Rs and CD-RWs using the  
procedure described below.  
2
Press and hold PS/A.ME until automatic presetting  
starts. “A MEM” appears on the display.  
The unit automatically stores up to 6 stations for  
each band.  
EJECT  
After completion of automatic presetting, the unit  
tunes in to all the stations stored on the preset  
station buttons in order (Preset Scan).  
Tocancelautomaticpresetting,pressPS/A.MEagain.  
INT  
RNDM  
REP1  
SRC  
Checking the preset stations (Preset Scan)  
1
Press PS/A.ME briefly.  
Each preset station will be tuned in for 5 seconds in  
order.  
1
2
Press z to open the front panel.  
Insert a CD.  
To cancel Preset Scan, press PS/A.ME again or any  
preset station button.  
The front panel will be closed automatically and  
“CD” appears on the display.  
CD play starts.  
If a CD is already inserted, press SRC repeatedly to  
select CD play mode.  
In normal play, when the last track finishes, the unit  
returns to the first track and continues to play.  
Presetting stations manually  
(Manual Memory)  
1
2
3
Press BAND repeatedly to select the desired band  
(F1, F2, F3, A1 or A2).  
Press TUNEi or TUNEk to tune in to a desired  
station (see “Tuning in to a station,” page 3).  
Pressandholdthedesiredpresetstationbuttonuntil  
the unit beeps.  
Labeled-side up  
Note  
A newly preset station replaces the station on the same  
band that was previously stored on that preset station  
button.  
CD indicator  
Elapsed playing time  
Tuning in to a preset station  
1
2
Press BAND repeatedly to select the desired band  
(F1, F2, F3, A1 or A2).  
Track number  
Press the preset station button on which the desired  
station is stored.  
To  
Press  
z*  
Eject a CD  
Skip to the next track  
t
r
Active tuning reception control (ATRC)  
The unit automatically suppresses FM noise caused by  
vehicle movement, and maintains sound quality.  
Go back to the beginning  
of the current track  
Each extra press skips  
backward one extra track  
Locate a specific point in Press and hold r or  
a track  
t until you find the  
point.  
* When you remove the CD, the front panel will be  
closed automatically after a while.  
To close the front panel manually, press z while the  
front panel is open.  
ENGLISH 4  
1
2
Connectacassette/MD/MP3portableplayerorother  
equipment via the unit’s AUX IN jack (3.5 mm dia.).  
PressSRCrepeatedlyuntilAUXINappearsonthe  
display.  
Notes  
• When you play a CD that is already inserted, CD play  
starts at the point where it stopped the previous time.  
A newly inserted CD starts from the first track.  
• A CD-R or CD-RW may take some time to start playing  
back, but this is not a malfunction.  
Note  
WhenaconnectingcordispluggedintotheAUXINjack,  
you cannot insert or eject a CD even if you press z. Be  
sure to disconnect the cord before inserting or ejecting  
the CD. Likewise, be sure to disconnect it before you  
turn off the ignition switch, otherwise the front panel  
won’t be retracted.  
• If a CD-R or CD-RW with no data or incompatible data  
is inserted, “ERROR03” will appear on the display.  
(See the section “TROUBLESHOOTING”.) The unit  
cannot play such discs.  
Intro Play  
You can locate a desired track by monitoring the first 10  
seconds of all the tracks on a CD.  
1
Press INT during CD play.  
“SCAN” appears on the display.  
OTHER FUNCTIONS  
2
Press INT again when the desired track is played.  
The unit returns to normal CD play.  
AUDIO CONTROL  
TUNE  
One Track Repeat Play  
You can play a track repeatedly.  
1
Press REP1 during CD play.  
“REP1” appears on the display.  
To cancel One Track Repeat Play, press REP1 again.  
SEL  
SRC  
Random Play  
You can play all the tracks in random order.  
Changing the display contrast  
1
Press RNDM during CD play.  
“RANDOM” appears on the display.  
1
2
Press and hold SRC until “CONT.” appears on the  
display.  
To cancel Random Play, press RNDM again.  
Turn AUDIO CONTROL to adjust the contrast.  
Note  
During Random Play, pressing r allows you to skip  
only to the beginning of the current track, not to the  
previous track.  
Changing the key illumination color  
Youcanchooseblueorredasthekeyilluminationcolor.  
1
2
3
Press and hold SRC until “CONT.” appears on the  
display.  
PressTUNEi or TUNEk until “ILL” appears on the  
display.  
AUXILIARY EQUIPMENT  
Turn AUDIO CONTROL to select 1 (for blue) or 2  
(for red).  
Listening to a cassette/MD/MP3  
portable player or other equipment  
Setting the dimmer of the display  
Youcanlistentomusicthroughequipmentconnectedto  
the unit. Refer to the operating instructions for the  
correspondingequipmentformoredetailedinformation.  
Be sure to remove any loaded CD to prevent possible  
damage to the unit before connecting the equipment.  
1
2
Press and hold SEL until “DIMMER” appears on the  
display.  
Turn AUDIO CONTROL to select 0 (bright) or  
1 (dimmed).  
SRC  
AUX IN jack  
5 ENGLISH  
Replacing the battery  
CARD REMOTE  
CONTROL  
1
Insert the tip of a pointed object A into the hole B  
and pull out the battery holder to remove the lithium  
battery (CR2025).  
Names of parts  
Remote control (back)  
BAND  
TAPE  
CD-CH  
CD  
SKIP  
REW  
FF  
TUNING / DISC  
UP  
DOWN  
Battery holder  
VOLUME  
2
Install a new lithium battery (CR2025) with the )  
side facing up in the battery holder.  
1 BAND button  
2 TAPE button (This button is not available with this  
unit.)  
3 CD button  
4 CD-CH button (CD changer only)  
5 SKIP f/REW button  
6 SKIP g/FF button  
3
Push the battery holder into the unit until it clicks.  
7 PS (preset) button  
8 TUNING/DISC UP/DOWN buttons  
9 VOLUME +/- buttons  
Preparations  
A lithium battery is installed in the remote control at the  
factory.  
Before you use the remote control, be sure to remove  
the insulating sheet by simply pulling it out.  
CAUTIONS  
• Keep the lithium battery out of the reach of children. If  
swallowed, consult a doctor immediately.  
• To prevent a short circuit, never pinch the battery with  
pliers, etc.  
Remote control (back)  
Insulating sheet  
ENGLISH 6  
One Disc Repeat Play  
You can play all tracks on a disc repeatedly.  
CD CHANGER OPERATION  
1
Press REP during CD Changer play.  
“REP” appears on the display.  
Playing a CD  
To cancel Repeat Play, press REP again.  
YoucanplayCDsfromaconnectedAIWACDChanger.  
For detailed information on installing a CD Changer,  
refertotheInstallationandConnectionmanualsupplied  
with the CD Changer.  
One Track Repeat Play  
You can play a track repeatedly.  
1
Press REP1 during CD Changer play.  
“REP1” appears on the display.  
RNDM  
To cancel Repeat Play, press REP1 again.  
One Disc Random Play  
You can play all the tracks on a disc in random order.  
1
Press RNDM during CD Changer play.  
“RANDOM” appears on the display.  
To cancel Random Play, press RNDM again.  
INT REP1  
REP  
SRC  
DISC  
Note  
During Random Play, pressing r allows you to skip  
only to the beginning of the current track, not to the  
previous track.  
1
Press SRC repeatedly to display “CD-CH.”  
The CD Changer play starts.  
CD Changer indicator  
Track number  
TROUBLESHOOTING  
Error code  
In the following cases the corresponding error code  
indication appears. Follow the suggestions below to  
solve such problems. If the error code indication does  
not disappear, consult an AIWA service center.  
CD number  
To  
Press  
t
Skip to the next track  
ERROR01 The disc magazine is not properly inserted  
in the CD Changer. Reinsert the magazine.  
Refer to the instruction manual for the CD  
Changer.  
ERROR02 No CDs are loaded in the disc magazine.  
Insert CDs properly. Refer to the instruction  
manual for the CD Changer.  
ERROR03 Focus error. Check that the CD is loaded  
properly (right side up, etc.), and the CD  
contains valid data.  
Skip back to the beginning of  
the current track or to the  
previous track  
r
Advance rapidly to locate a  
desired point  
Press and hold t,  
then release it at the  
desired point  
Reverse rapidly to locate a  
desired point  
Press and hold r,  
then release it at the  
desired point  
Start CD Changer play from DISCN  
ERROR04 Problem with the CD Changer. Reset the  
unitbypressingtheresetbutton. Ifthisdoes  
not solve the problem, consult an AIWA  
service center.  
the first track on the next disc  
Start CD Changer play from DISCM  
the first track on the previous  
disc  
Intro Play  
You can locate a desired track by monitoring the first 10  
secondsofallthetracksontheCDsinthediscmagazine.  
1
Press INT during CD Changer play.  
“SCAN” appears on the display.  
2
Press INT again when the desired track is played.  
The unit returns to normal CD play.  
7 ENGLISH  
Reset button  
GENERAL  
IfaCDdoesnotoperateproperly, presstheresetbutton  
with a pointed object such as a pencil, etc. Note that all  
your settings will be erased if this button is pressed.  
Power-Supply Voltage: 14.4 V (11 to 16 V  
allowable), DC, negative ground  
Load Impedance: 4  
Tone Control: Bass ± 10 dB at 100 Hz, Treble ±  
10 dB at 10 kHz  
Preamp Output Voltage (load impedance): 2.2 V  
(10 k)  
Installed size: 182 (W) × 53 (H) × 155 (D) mm  
(7 1/4 (W) × 2 1/8 (H) × 6 1/8 (D) inches)  
CARD REMOTE CONTROL  
Dimensions: approx. 33 (W) × 85 (H) × 7.5 (D) mm  
(1 5/16 (W) × 3 3/8 (H) × 5/16 (D) inches)  
Reset button  
Weight: approx. 20 g (0.7 oz.) (including battery)  
MAINTENANCE  
• Specifications and external appearance are subject to  
change without notice due to product improvement.  
Cleaning the front panel  
Wipe the surface with a soft, dry cloth.  
REAR PANEL  
SPECIFICATIONS  
RADIO SECTION  
(FM)  
Frequency Range: 87.5 MHz – 108 MHz  
Usable Sensitivity: 12.7 dBf  
50 dB Quieting Sensitivity: 17.2 dBf  
IF Rejection: 100 dB  
For details, refer to the separate “INSTALLATION AND  
CONNECTIONS”.  
Frequency Response: 30 Hz – 15,000 Hz  
S/N Ratio: 70 dB  
Stereo Separation: 35 dB at 1 kHz  
Alternate Channel Selectivity: 90 dB  
Capture Ratio: 3 dB  
The word “BBE” and the “BBE symbol” are trademarks  
of BBE Sound,Inc.  
Under licence from BBE Sound,Inc.  
(AM)  
Frequency Range: 530 kHz – 1,710 kHz  
Usable Sensitivity: 30 µV (30 dB)  
CD SECTION  
Frequency Response: 17 Hz – 20 kHz +0/–3 dB  
Dynamic Range: More than 92 dB  
Channel Separation: More than 60 dB  
S/N Ratio: More than 90 dB  
Wow/Flutter: Unmeasurable  
AUDIO SECTION  
Max. Power Output: 45 W × 4 channels  
AUX IN input  
Input sensitivity (load impedance) AUX IN: 300 mV  
(10 k)  
ENGLISH 8  
Printed in Indonesia  

Alesis POWER AMPLIFIER RA150 User Manual
Boss Audio Systems BOSS PHANTOM PH3000D User Manual
Bunn Beverage Dispenser 2SH User Manual
Bushnell 26 0224W User Manual
Canon UC 5000 User Manual
Dual Car Speaker DMP67 User Manual
Hobie 30113 User Manual
Huey Chiao HCB38 User Manual
IDEAL INDUSTRIES CLASSIC HE18 User Manual
JVC GR DVL920 User Manual