Advantech TREK 305R User Manual

User Manual  
TREK-305R  
5.7” Display Solution for Vehicle  
Application  
Packing List  
Before you begin installing your device, please make sure that the following materials  
have been shipped:  
TREK-305 device  
Display cable (Advantech P/N: 1700009873) to connect with VITA-350P  
If any of these items are missing or damaged, contact your distributor or sales repre-  
sentative immediately.  
iii  
TREK-305R User Manual  
Ordering information  
Part Number  
Description  
TREK-305R-FLA0E  
5.7" color TFT LCD with touch screen, 2 Watt speaker, and Power  
button  
VITA-350P-GA0E  
MDT with GPS, GPRS, DI/O, RS232, LVDS (TREK is design com-  
patible with VITA)  
TREK-305R User Manual  
iv  
Declaration of Conformity  
根據交通部低功率管理辦法規定:  
第十二條  
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更  
頻率、加大功率或變更原設計之特性及功能。  
第十四條  
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應  
立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信規定作業之無  
線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備  
之干擾。  
FCC  
This device complies with the requirements in part 15 of the FCC rules: Operation is  
subject to the following two conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept any interference received, including interference that  
may cause undesired operation This equipment has been tested and found to  
comply with the limits for a Class A digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environ-  
ment. This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instruction manual, may  
cause harmful interference to radio communications. Operation of this device in  
a residential area is likely to cause harmful interference in which case the user  
will be required to correct the interference at his/her own expense. The user is  
advised that any equipment changes or modifications not expressly approved  
by the party responsible for compliance would void the compliance to FCC regu-  
lations and therefore, the user's authority to operate the equipment.  
Caution! There is a danger of a new battery exploding if it is incorrectly installed.  
Do not attempt to recharge, force open, or heat the battery. Replace the  
battery only with the same or equivalent type recommended by the man-  
ufacturer. Discard used batteries according to the manufacturer°Øs  
instructions.  
Additional Information and Assistance  
est information about the product.  
2. Contact your distributor, sales representative, or Advantech's customer service  
center for technical support if you need additional assistance. Please have the  
following information ready before you call:  
Product name and serial number  
Description of your peripheral attachments  
A complete description of the problem  
The exact wording of any error message  
v
TREK-305R User Manual  
TREK-305R User Manual  
vi  
Contents  
Chapter 1 General Information ............................1  
Appendix A LCD Specification................................9  
Appendix B Touch Panel Specification................13  
vii  
TREK-305R User Manual  
TREK-305R User Manual  
viii  
Chapter  
1
1
General Information  
This chapter gives background  
information on the TREK-305.  
Sections include:  
Introduction  
Features  
Quick Installation Guide  
System Dimensions  
 
1.1 Introduction  
Advantech TREK-305R uses a Toshiba 5.7” LCD panel with touch (Toshiba model  
no: LTA057A344F-12), which is the perfect size to fit into tight spaces for fleet man-  
agement and dispatching purposes. TREK-305R of 5.7" touch screen panel provides  
excellent capabilities and features with industrial standard VESA mounting holes,  
light-weight housing, and convenient mounting accessories. The TREK-305 design is  
compatible with VITA-350P-GA0E.  
Figure 1.1 VITA-350P and TREK-305R total solution  
TREK-305R User Manual  
2
   
1.2 Features  
Type  
QVGA TFT LCD (Toshiba LT057A344F)  
18 bits (256 k)  
Colors  
Resolution  
320 x 240  
Size (disgonal)  
Pixel Pitch  
5.7” (4:3)  
0.36 (W) x 0.36 (W)  
H: 140°, V: 120°  
320 nits by LED backlight  
4-wire resistive  
500  
Display  
View Angle (H°, V°)  
Brightness  
Touchscreen  
Contrast Ratio  
Backlight Life Time (hrs)  
LVDS  
20000  
1 x 26 pin connector  
2 Watt speaker out  
3.3 V and 5 V  
I/O  
Audio  
DC Input  
Power  
LCD power button  
Power Consumption  
Mounting  
Push button  
1.3 W  
VESA mount (30 x 38 mm, 75 x 75 mm)  
PC  
Material  
Mechanical  
Enviroment  
Weight  
400 (g)  
Dimension W x H x D (mm)  
Operating Temperature  
Storage Temperature  
Vibration  
168.55 x 128.05 x 35.6  
-10 ~ 70°C  
-30 ~ 80°C  
MIL-STD-810F 514.5C-3  
FCC 47 CFR part 15B  
ICES-003 issue 4  
EN55022/55024  
ECE-R10 (v.03)  
CNS 13438  
FCC  
IC  
Certification  
CE  
E13  
BSMI  
3
TREK-305R User Manual  
 
1.3 Quick Installation Guide  
1. Connect 26pin connector to 5.7” panel.  
36pin (S2)  
connect to  
VITA series  
26 pin (S1)  
connect to  
TREK-305R  
DI/O (default: 4 Digital output)  
Figure 1.2 - 2 m cable connecting VITA and TREK  
2. Connect 36pin connector to VITA-350P.  
2 types of VESA mount:  
30 x 38mm and 75 x 75mm  
Speaker  
Warranty void if sticker is removed.  
Please refer to Advantech RMA policy  
Figure 1.3 Backside of TREK-305R  
TREK-305R User Manual  
4
     
Power button to control LCD backlight On/Off  
When LCD backlight is on, red LED light is on  
Figure 1.4 Front side of TREK-305R  
Pin definition (on TREK)  
Connector vendor: 3M Touch systems, p/n: 10226-55G3PC  
Figure 1.5 26-pin connector  
Pin definition (on VITA)  
Connector vendor: 3M Touch systems, p/n: 10236-55G3PC  
Figure 1.6 36-pin connector  
5
TREK-305R User Manual  
     
36 pin  
CITA-350P Side  
26 pin  
TREK-305R Side  
1
LVDS Data0+  
LVDS Data0-  
LVDS Data1+  
LVDS Data1-  
GND  
1
LVDS Data0+  
LVDS Data0-  
LVDS Data1+  
LVDS Data1-  
GND  
2
2
3
3
4
4
5
5
6
T/S signal X+  
T/S signal Y+  
T/S signal X-  
T/S signal Y-  
GND  
6
T/S signal X+  
T/S signal Y+  
T/S signal X-  
T/S signal Y-  
GND  
7
7
8
8
9
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
GPIO  
GPIO  
DC +5 V  
DC +5 V  
DC +5 V  
DC +5 V  
LVDS Data2+  
LVDS Data2-  
LVDS Data3+  
LVDS Data3-  
LVDS Clock+  
LVDS Clock-  
GND  
LVDS Data2+  
LVDS Data2-  
LVDS Data3+  
LVDS Data3-  
LVDS Clock+  
LVDS Clock-  
GND  
Line in  
Line in  
GPIO  
GPIO  
GPIO  
GPIO  
GPIO  
GPIO  
DC +3.3 V  
DC +3.3 V  
DC +3.3 V  
DC +3.3 V  
5 pin  
DI/DO Side  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
GPIO1  
1
2
3
4
5
GPIO1  
GPIO2  
GPIO3  
GPIO4  
GND  
GPIO2  
GPIO3  
GPIO4  
GND  
X (empty PIN)  
X (empty PIN)  
X (empty PIN)  
X (empty PIN)  
X (empty PIN)  
TREK-305R User Manual  
6
TREK-305R is design compatible with VITA-350P.  
Figure 1.7 Front side of VITA-350P  
1.4 System Dimensions  
Unit: mm  
Power button height: 1.41 mm  
Figure 1.8 System Dimensions  
7
TREK-305R User Manual  
     
TREK-305R User Manual  
8
Appendix  
A
A
LCD Specification  
 
A.1 LCD General Specification  
Item  
Specifications  
Display Mode1)  
VIewing Direction  
Driving Method  
TN colors (64 gray scales, 256 k colors)  
6 o’clock (in direction of maximum contrast)  
TFT active matrix  
CLK (clock), DE (Data Enable signal)  
H-sync, V-sync (Synchronization signal)  
R5, R4, R3, R2, R1, R0 (Red display data)  
G5, G4, G3, G2, G1, G0 (Green display data)  
B5, B4, B3, B2, B1, B0 (Blue display data)  
R/L, U/D (Reverse Scan Control)  
Input Signals  
Dimensional Outline2)  
Active Area  
144.0 (W) x 104.6 (H) x 10.0 max. (D) (mm)  
115.2 (W) x 86.4 (H) (mm)  
115.4 (W) x 86.6 (H) (mm)  
320 (W) x 240 (H) (mm)  
Viewing Area  
Number of Pixels3)  
Pixel Pitch3  
Pixel Arrangement3  
Surface treatment  
Backlight  
0.36 (W) x 0.36 (H) (mm)  
RGB vertical stripes  
Anti-glare and hard cost 3H on LCD surface  
18 LEDs (3 rows) for sidelighting  
Note!  
1. k=1024.  
2. Excluding backlight cables.  
3. Display area address is as follows.  
TREK-305R User Manual  
10  
 
A.2 LCD Optical Specification  
Specifications  
Item  
Symbol Conditions  
Unit Remark  
Min. Typ. Max.  
30  
40  
40  
40  
50  
70  
70  
70  
-
-
-
-
°
°
°
°
-
=180°  
=0°  
Viewing Angle  
CR >=10  
=90°  
=190°  
Contrast Ratio  
Response Time  
CR  
350 500 -  
=0°,  
=0°  
tON  
-
-
15 25  
25 35  
ms  
ms  
=0°,  
tOFF  
=0°  
cd/m2  
/F=12 mA  
Luminance  
L
255 320 -  
=0°,  
=0°  
Gray Scale Level=163  
(White)  
Luminance Uniformity LUNF  
XR  
60  
70  
-
%
Gray Scale Level: L63  
0.52 0.59 0.66 -  
0.27 0.34 0.41 -  
Red  
YR  
=0°,  
Ditto  
=0°  
XG  
0.29 0.36 0.43 -  
0.48 0.55 0.62 -  
0.08 0.15 0.22 -  
0.05 0.12 0.19 -  
0.25 0.32 0.39 -  
0.27 0.34 0.41 -  
Green  
YG  
Chromaticity  
XB  
Blue  
Ditto  
Ditto  
YB  
XW  
White  
YW  
Note!  
1. Refer to “11. Measuring Method“.  
2. The above test limit must be applied for initial use. Characteristics  
will be shifted by long period operation, but it is not irregular phe-  
nomena. Theoretically brightness characteristics will be decreased  
due to color shift.  
11  
TREK-305R User Manual  
 
TREK-305R User Manual  
12  
Appendix  
B
B
Touch Panel  
Specification  
 
B.1 Enviroment Specification  
Chemical Resistance  
(top surface)  
Toluene, Acetone, Methanol, Alcohol, Ethylacetate, Artificial sweat,  
Petroleum ether  
Condition: Tested after leaving the chemical on the surface for 3 minutes being wiped  
off by cloth.  
Judgment: Must be no effect in appearance.  
B.2 Mechanical Characteristics  
Operating Life  
Input (finger)  
10,000,000 hits (Note 1)  
Character Input (pen)  
100,000 characters (Note 2)  
Note!  
1. Testing rod (Figure 1), Load 250 g, Cycle 2hit/sec;  
2. Testing rod (Figure 2), load 250 g, Input size 10 x 10 mm, Input  
character A to Z / minute.  
These (finger and pen) are tested at same point of the panel surface,  
and all point will become dis-functin after test.  
Silicon Rubber  
(Hardness: 60°)  
Tip: R = 4.0  
Polyacetal resin  
Tip: R = 0.8  
Figure 1 Testing rod 1  
Figure 2 Testing rod 2  
B.3 Mechanical Characteristics  
Pressing Force  
Activation Force  
Surface Hardness  
Max 100N (Note 3)  
0.05N to 1.0N  
Over 3H (by JIS pencil hardness) (Note 4)  
Note!  
3. Testing with rubber rod. (Ø 16 mm, Hardness 60°), Time: 5 s, Center  
of LCD surface. If you apply pressure over 100N, white spots and  
dark spots will be occured.  
4. Testing pressure is 750 g. If you use 3H hardness pencil with under  
750 g pressure, the surface will not be damaged. But using a 4H  
hard pencil, the surface may be damaged. Please use a 3H pencil  
or under with under 750 g pressure.  
TREK-305R User Manual  
14  
     
15  
TREK-305R User Manual  
Please verify specifications before quoting. This guide is intended for reference  
purposes only.  
All product specifications are subject to change without notice.  
No part of this publication may be reproduced in any form or by any means,  
electronic, photocopying, recording or otherwise, without prior written permis-  
sion of the publisher.  
All brand and product names are trademarks or registered trademarks of their  
respective companies.  
© Advantech Co., Ltd. 2008  

A O Smith DW 1810 User Manual
Arcam digital radio tuner DT81 User Manual
Campbell Hausfeld IF5530 User Manual
Clarion Car Stereo System VXZ756 User Manual
Cornelius Millennium II 6000 User Manual
Crown Boiler XE 2 User Manual
Cuisinart Smart Stick CSB 76DB User Manual
Eclipse Fujitsu Ten Car Stereo System CD8455 User Manual
Hitachi DZ GX5060E User Manual
HP (Hewlett Packard) Compaq LA2205WG User Manual