Acnodes RM 6193 User Manual

RM 6193  
8U 19” Rack Mount High brightness  
LCD Monitor  
User’s Manual  
Rev 1.0  
RM 6193 User manual  
Safety Instructions  
1. Please read these safety instructions carefully.  
2. Please keep this User’s Manual for later reference.  
3. Please disconnect this equipment from AC outlet before cleaning. Don’t use liquid or sprayed  
detergent for cleaning. Use moisture sheet or clothe for cleaning.  
4. For pluggable equipment, the socked-outlet shall be installed near the equipment and shall be  
easily accessible.  
5. Please keep this equipment from humidity.  
6. Lay this equipment on a reliable surface when install. A drop or fall could cause injury.  
7. Do not leave this equipment in an environment unconditioned, storage temperature above 600 C,  
it may damage the equipment.  
8. The opening on the enclosure is for air convection hence the equipment from overheating. DO  
NOT COVER THE OPENING.  
9. Make sure the voltage of the power source connect the equipment to the power outlet.  
10. Please keep the power cord such a way that people can not step on it. Do not place anything over  
power cord. The power cord must rate for the voltage and current marked on the product’s electrical  
ratings label. The voltage and current rating of the cord should be greater than the voltage and the  
current rating marked on the product.  
11. All cautions and warning on the equipment should be noted.  
12. If the equipment is not in use for long time, disconnect the equipment from mains to avoid being  
damaged by transient over-voltage.  
13. Never pour any liquid into ventilation openings; this could cause fire or electrical shock.  
14. Never open the equipment. For safety reason, qualified service personnel should only open the  
equipment.  
15. If one of the following situations arises, get the equipment checked by service personnel.  
The Power Cord or plug is damaged.  
Liquid has penetrated into the equipment.  
The equipment has been exposed to moisture.  
The equipment has not worked well or you can not get it work according to User’s Manual.  
The equipment has dropped and damaged.  
If the equipment has obvious signs or breakage.  
Acnodes Corporation, www.acnodes.com, [email protected]  
3
RM 6193 User manual  
Index of Contents  
Packing List ...............................................................................................................2  
Safety Instructions.....................................................................................................3  
Index of Contents ......................................................................................................4  
1. General Information............................................................................................5  
1.1 Overview ..................................................................................................5  
1.2 Product Specification ...............................................................................6  
2. Rack Mount Installation.......................................................................................7  
3. OSD Menu ..........................................................................................................8  
3.1 OSD Menu Membrane Switch ................................................................8  
3.2 On Screen Display Menu .........................................................................9  
4. Connecttion Diagram ........................................................................................11  
4.1 Video Connection Diagram ....................................................................11  
4.2 Touch Screen Connection Diagram.......................................................12  
5. Touch Screen Specification ..............................................................................13  
6. DC Input power Supply (option)........................................................................14  
7. Trouble shooting .............................................................................................15  
Acnodes Corporation, www.acnodes.com, [email protected]  
4
RM 6193 User manual  
1. General Information  
1.1 Overview  
The RM6193 is a 8U rack mount LCD monitor with 19” 800-nit 1280 x 1024 TFT LCD  
monitor and rugged metal black color front bezel. This monitor comes with a standard  
15-pin VGA video input and front access OSD membrane switch. Optional Video-input  
for S-video / BNC / RCA connector and USB or PS/2 type resistive-type touch. RM  
6193 comes with an external 110/220VAC power adapter, 24/48 VDC power input is  
available for customer’s application.  
1. 19” 1280 x 1204 high brightness TFT LCD monitor  
2. Membrane OSD Menu switch  
3. External 110/220VAC power adapter with bracket  
Acnodes Corporation, www.acnodes.com, [email protected]  
5
RM 6193 User manual  
1.2 Product Specification  
Model name  
RM 6193  
Dimension  
Net Weight  
480 x 76 x 354.8mm/18.9 x 3" x 14inches  
8 Kg / 18 lbs  
Display Size  
Panel Type  
Resolution  
Capabilities  
Viewing Angle  
(CR>10)  
19 inches  
Active Matrix TFT LCD  
Maximum Resolution up to 1280 x 11024  
Right-Left view 160°(Typ)  
Up-Down View 160°(Typ)  
Contrast Ratio  
Brightness  
Tr Response  
Time (ms)  
700:1  
White 800 cd/m² (Center 1 point Typ)  
1.3 ms  
Supported Colors 16.7M Colors (6-bit with FRC)  
Display Area  
(mm)  
376 x 301  
VGA Signal Input Analog RGB, 0.7Vp-p  
Sync. Type  
Resolution  
Separate H/V, Composite, SOG  
640 x 350, 70 Hz  
720 x 400, 70 Hz  
640 x 480, 60/ 72/ 75 Hz  
800 x 600, 60/ 70/ 72/ 75 Hz  
1024 x 768, 60/ 70/ 72/ 75 Hz  
1152 x 864, 60/ 70/ 75 Hz  
1280 x 1024, 60/ 70/ 75 Hz  
Cables  
1 x 6’ D-sub VGA male to male Cable  
Plug & Play DDC EDID 1.3  
Power Source  
Auto-sensing 100 to 240VAC, 50 / 60Hz  
Power  
Max. 40 Watt, Standby 5 Watt  
Consumption  
Temperature  
Operate 0 ~ 50°C / 32 ~ 122°F  
Storage -20 ~ 60°C / -4 ~ 140°F  
10% ~ 90% RH  
10G acceleration (11ms duration)  
5~500Hz 1G RMS random vibration  
Heavy duty steel materials  
Humidity  
Shock  
Vibration  
Chassis  
Construction  
Certification  
CE / FCC, ROHs Compliance  
Acnodes Corporation, www.acnodes.com, [email protected]  
6
RM 6193 User manual  
2. Rack mount Installation  
1. Find the property position and size to screw rack mount front bezel onto the  
server rack mount first.  
2. Lift & push the rack mount monitor into the rack cabinet, and screw between  
bracket and rack mount monitor with screws.  
Acnodes Corporation, www.acnodes.com, [email protected]  
7
RM 6193 User manual  
3. OSD Menu  
3.1 OSD Menu Membrane Switch  
Acnodes Corporation, www.acnodes.com, [email protected]  
8
RM 6193 User manual  
3.2 On screen Display menu  
BRIGHTNESS / CONTRAST  
Brightness: Adjust background black level of the screen image.  
Contrast: Adjust the difference between the image background (black level)  
and the foreground (white level).  
AUTO ADJUST  
Auto Adjust: Fine tunes the video signal to eliminate waviness and distortion. A  
"Adjusting" message is displayed during the process.  
Auto Tune: Optimize phase, clock, position and size. An "Adjusting" message is  
displayed during the process.  
PHASE/CLOCK  
Phase / Clock: To enter into the phase & clock sub menu  
H/V POSITION  
H/V Position:  
Align the screen image left or right and up or down.  
MISC  
Information: Display the current resolution, refresh rate and frequency  
information on the screen.  
OSD Timer  
Set the time duration in seconds that the OSD is visible after the last button is  
pressed. The factory default is 10 seconds.  
Acnodes Corporation, www.acnodes.com, [email protected]  
9
RM 6193 User manual  
Color  
Select the screen color - 5500K, 6500K & 9500K. The factory default is 9500K.  
Language  
Select the language in which the OSD menu is displayed -  
English, Chinese (中文), Japanese (日本語), German, French, Spanish, Italian  
RESET  
Restore the settings to factory defaults.  
Acnodes Corporation, www.acnodes.com, [email protected]  
10  
RM 6193 User manual  
4. Connecton Diagram  
The RM6193 comes with a standard 15-pin VGA video input and external  
110/220VAC power adapter.  
Optional Video-input for S-video / BNC / RCA connector and USB or PS/2 type  
resistive-type touch.  
4.1 Video-input Connection Diagram  
15-pin D-sub VGA  
15-pin D-sub VGA and DVI-D  
15-pin D-sub VGA, S-video and RCA  
15-pin D-sub VGA, S-video and BNC  
Acnodes Corporation, www.acnodes.com, [email protected]  
11  
RM 6193 User manual  
4.2 Touch Screen Connection Diagram  
15-pin D-sub VGA and USB-type touch screen  
15-pin D-sub VGA and Serial-type touch screen  
Acnodes Corporation, www.acnodes.com, [email protected]  
12  
RM 6193 User manual  
5. Touch Screen Specification  
Touch screen  
type  
Resistive-type  
Interface  
USB or PS/2  
82%±5%  
Optical  
transmittance  
Surface hardness 3H (JIS K5400)  
Operating system Windows 98 / 2000 / ME / XP / NT / CE,  
DOS, Linux  
Touch screen  
type  
Capacitive-type  
Interface  
USB or PS/2  
88%  
Optical  
transmittance  
Surface hardness Mohs’ hardness rating: 6  
Operating system Windows 98 / 2000 / ME / XP / NT / CE,  
DOS, Linux  
Remarks  
USB touch screen package includes an extra 6ft USB cable, quick reference guideline and  
CD disc  
Serial touch screen package includes an extra 6ft serial cable, quick reference guideline and  
CD disc  
For detailed information, please refer to the attached CD disc  
As the touch screen unit is not made of toughened glass, please handle it carefully.  
Acnodes Corporation, www.acnodes.com, [email protected]  
13  
RM 6193 User manual  
6. DC Input Power Supply (Option)  
Acnodes Corporation, www.acnodes.com, [email protected]  
14  
RM 6193 User manual  
7. Trouble shooting  
1. How do I adjust the resolution?  
To change monitor resolution, click Start -> Control Panel -> Display. Select Setting  
tab to adjust the monitor resolution in Desktop Area. The available resolutions, "640  
x 480", "800 x 600", "1024 x 768", "1152 x 864", "1280 x 1024", are deter- mined by  
the display card in your computer.  
2. Is interference signal appeared on LCD normal when shutting down the  
computer ?  
In rare cases, interference may appear on the monitor. This may be caused by  
signal rate of VGA card and is considered normal. The image quality can be  
improved by adjusting the phase or pixel rate automatically or manually.  
3. The membrane button power light is not ON  
Press the power On / Off on LCD membrane button to check if the monitor is in the  
ON mode. Check the power cord is properly connected to the LCD keyboard  
drawer and power outlet.  
4. Screen image is not centered or sized properly  
Press the  
button for two seconds to automatically adjust the image. Adjust the  
H-position and V-position settings via On-screen menu.  
Acnodes Corporation, www.acnodes.com, [email protected]  
15  

Apple iMovie HD User Manual
Ashly KLR 5000 User Manual
Boston Acoustics GTA 800M User Manual
Braun MR 4000 CA User Manual
Bunn TD4T DR User Manual
Canon EF S18 User Manual
Casio Fx 115esplus Scientific Calculator fx115ESPlus User Manual
Curtis KCR2614A User Manual
JVC Digital Camcorder GZEX250BUS User Manual
JVC GR D31US User Manual