416 Preliminary Quick Guide
About, Software, Tools, Safety
Camera Left & Front
3
4
5
Camera Right & Back
Quick Specs
6
7
Power On, Camera RUN, Inching, Camera Display
Loading the Magazine
8
Mounting the Magazine
Changing fps & Shutter Angle
Beeper, Backlight & RGB ARRIGLOW
On-board Battery OBB-2
Integrated Video System
Accessories
10
11
12
13
14
16
18
20
Timecode Operation
ARRI Group Addresses
05/2006
About, Software, Tools, Safety
About the 416 Preliminary Quick Guide
This Quick Guide (order number K5.40076.0) provides a short introduction to the ARRIFLEX 416. This guide
does not replace the ARRIFLEX 416 User’s Guide (K5.40077.0). It is essential that you acquaint yourself with
the user’s guide before operating the equipment.
Even though all efforts have been made to ensure this guide’s accuracy, changes and upgrades to the products
described can result in different hardware or behavior. Technical data are subject to change without notice.
These documents can be downloaded from www.arri.com in Acrobat pdf format. The Acrobat Reader can be
Software Version
This guide describes the ARRIFLEX 416 with preliminary Software Packet 01A. Different software versions can
result in different behaviour. Authorized ARRI Service Centers can check and update equipment software.
Tools
Anyone operating the ARRIFLEX 416 system should have these tools:
1. A 1.5 mm metric hex wrench is used to adjust the alignment and focus of the Integrated Video System.
2. A 3 mm metric hex wrench is used to attach and remove camera components and most accessories.
3. A 5 mm metric hex wrench is used to attach or remove the 3/8” Accessory Shoe Adapter, the LWS-5 and
the WHA-2 Rosette Bracket.
4. A 8-10mm (5/16”) flathead screwdriver is used to attach baseplates.
Safety Specifications
• Never place your hand in the lens port or inside of the camera while it is running.
• Assembly and initial operation should be carried out only by persons who are familiar with the equipment.
• Switch camera power off before making electrical connections.
• Never run the camera without a lens or a protective cap mounted in the lens port.
• Never attempt to remove the magazine while the camera is running.
• Always ensure that the camera is securely mounted.
• Repairs should be carried out only by authorized ARRI service centers.
• Use only original ARRI replacement parts and accessories!
• In wet weather conditions the normal safety precautions for handling electrical equipment should be taken.
• Clean optical surfaces only with a lens brush or a clean lens cloth. In case of solid dirt moisten a lens cloth
with pure alcohol or a brand name lens cleaner.
• Do not use solvents to clean the film path, Plexiglas parts or rubber seals.
• Do not remove any screws which are secured with paint.
ARRIFLEX 416 Quick Guide 05/2006, Page 3
Camera Left & Front
Eyepiece focus ring
Flip-out tape hook
416 Standard
Camera Handle
Image rotation
knob
Optional centre leg
Timecode sensitivity
switch
Magazine feed
side door lock
Heated Eyepiece
outlet
DIMMER
—
+
Tape hook
NORM
PS/CCU
LOCK
PHASE
RGB ARRIGLOW
brightness buttons
RUN
MODE
SEL/∆
SET/ V
PHASE button
Display
416 Shoulder
Magazine 120/400
RUN button
RUN Indicator
Image rotation knob
Tape hook
PL lens port
(Super 16 only)
Front 3/8 – 16
mounting point
ARRIFLEX 416 Quick Guide 05/2006, Page 4
Camera Right & Back
Antenna
RF CHANNEL
selector
RF READY
LED
Integrated
Video System
Magazine release
lever
On-board Battery
release button
Magazine
take-up side
door lock
Eyepiece
swing over lock
L
R
L
R
L
R
RDY
Motor control LEDs
LDD
Lens motor
direction switches
RF CHAN
ON/OFF
TCC
LCS
LCS
RUN
CLM-2 motor
connectors
RS
RS
Lens Data
Display
connector
Timecode
connector
Attachment
rosette
Power on/off
switch
RS
connectors
LCS
connectors
RUN
indicator
Pitch
adjust
RUN
button
Eyepiece rotation
friction
IVS ground fault
indicator
MINI MONITOR
connector
BNC connectors
Magazine film
reserve counter
Power connector
(BAT)
REMOTE connector
ARRIFLEX 416 Quick Guide 05/2006, Page 5
Quick Specs
Fps range:
1 to 75 fps, forward only, in 0.001 fps increments
Mirror Shutter:
180º to 45º, manually adjustable
Fixed settings at: 180º, 172.8º, 150º, 144º, 135º, 90º, 45º
Use the following angles for filming with non-electronic ballast HMI
or fluorescent lighting:
180º:
25 fps, 50 Hz supply, 1/50th second exposure time
172.8º: 24 fps, 50 Hz supply, 1/50th second exposure time
150º:
144º:
25 fps, 60 Hz supply, 1/60th second exposure time
24 fps, 60 Hz supply, 1/60th second exposure time
Power:
24 V DC, custom 105 Fischer connector, pin 1 is 0 V, pin 2 is positive,
pin 3 is on-board battery condition monitor
Acceptable range: 21 V to 35 V
Accessory Power:
1 x 24 V RS connector on 416
2 x 24 V RS connectors on 416 Plus
1 x 24 V REMOTE connector
RS & REMOTE connectors combined 2 A continuous, 4 A peak
Note: RS & REMOTE connectors are not regulated so their output voltage tracks the
camera supply voltage.
1 x 24 V Heated Eyecup connector
2 x 12 V MINI MONITOR connector on IVS
MINI MONITOR connectors combined 2 A continuous
Movement:
One pull-down film transport claw and one registration pin
Less than 20 dB (A) @ 24 fps
Sound Level:
Lens Mount:
54 mm PL mount, Super 16 only
52.00 – 51.99 mm
Flange Focal Distance:
Temperature Range:
Electronic Accessories:
-20ºC to +50ºC (+4ºF to +122ºF)
LDD-FP
Lens Data Display for Focus Puller (Lens Data Archive only)
UMC-3 Universal Motor Controller
EXD-1
RCU-1
LCS
External Display
(Accessory expansion cable needed)
Remote Control Unit
Lens Control System
Wireless Remote System
WRS
WRC-1 Wireless Remote Control
ESU-1
ICU-1
RS-4
External Synchronization Unit
Iris Control Unit
Remote On/Off Switch
(Accessory expansion cable needed)
(Accessory expansion cable needed)
Other Accessories:
16SR 3 fibre screens, HE-3, 4 & 5 heated eyecups, FF-3 (with bridge plate), FF-4 &
5 (on lightweight support rods or bridge plate), 15 mm & 19 mm support rod matte
boxes (with bridge plate), ARRI/Zeiss Ultra 16 lenses, ARRI/Zeiss Lightweight Zoom
LWZ-1, ARRI/Zeiss Standard Speed lenses, ARRI/Zeiss Super Speed lenses,
ARRI/Zeiss Ultra Prime lenses, ARRI/Zeiss Master Prime lenses, Cooke S-4 lenses,
ARRI Macro lenses, Cooke & Angenieux zoom lenses, ARRI/Zeiss Variable Prime lenses.
Not compatible with:
16SR magazines, 16SR on-board batteries, 435 Single Frame Hand Controller,
CCU and ARRICAM electronic accessories.
ARRIFLEX 416 Quick Guide 05/2006, Page 6
Power On, Camera RUN, Inching, Camera Display
Turning Camera Power On
The Power On button for the ARRIFLEX 416 is located above the RUN button on the camera right side. To turn
the camera On, briefly press the Power On button. When a battery is connected to the camera and the power
switch is turned on, you should see characters appear on the Display on the camera left side.
Note: The camera remembers the status of the Power On button and restores this status after a power interruption.
PHASE button
RF CHAN
ON/OFF
NORM
PS/CCU
LOCK
TCC
LCS
PHASE
Power On button
RUN button
RUN
RUN
RS
RS
LCS
MODE
SEL/∆
SET/ V
RUN indicator
Camera RUN
A RUN button is located on both sides of the camera. To run the camera, press the RUN button briefly. The
RUN indicator light will glow red while the camera comes up to speed, changing to green once the set frame
rate is reached. The RUN indicator light will glow steadily green while the camera runs at the set frame rate.
To stop the camera, briefly press the RUN button again. If the RUN indicator glows red while the camera is in
Standby, the camera is not ready and pressing the RUN button will have no effect.
Inching
The ARRIFLEX 416 cannot be manually inched – it can only be inched by pressing the PHASE button while the
camera is in Standby. If the PHASE button is pressed briefly, the mirror shutter will rotate 180º to allow for gate
checks. To move the mirror shutter back into viewing position, press the PHASE button again briefly.
Camera Display
The Camera Display indicates the status of, or value assigned to, the various camera parameters. There are
seven modes which show the following information:
1.
2.
3.
Total film exposed (or take counter)
Standard speed.
5.
6.
7.
Timecode User Bits
Timecode User Bits
Loudspeaker sequence & volume
Button backlight brightness
Programmed speed.
Take counter (or total film exposed)
Supply voltage & (with OBB-2),
battery capacity/magazines left.
ARRIGLOW colour
4.
Timecode hours & minutes
Timecode minutes & framerate
Display Indicators:
asy:
bat:
Asynchronous operation (camera is not running at set fps)
Low battery (less than 20 volts)
end:
Camera has run out of film
fps flashes:
PROG:
TC glows:
TC flashes
ESU is not receiving a valid signal
Internal program is activated
Timecode exposure is enabled and timecode is set
Timecode exposure is enabled but not recording properly
Viewfinder Indicators:
LED glows:
LED flashes
Asynchronous operation (camera is not running at set fps)
Low battery (less than 20 volts)
ARRIFLEX 416 Quick Guide 05/2006, Page 7
Loading the 416 Magazine
Note: The 416 magazine has its feed and take-up chambers on opposite sides to the SR 1, 2 & 3 magazines.
Step 1: The Feed Side
Load the unexposed film into the feed side in absolute darkness (darkroom or changing tent).
• Open the feed side magazine door and latch back the lay-on roller arm.
• Remove the film from the film can.
• Remove the tape from the film head. Ensure that the tape is completely removed and secured out of the way.
• Place the film roll on the core holder so it unwinds in the direction shown in the picture below. Press it down fully.
Note: When placing film on the feed side core holder, do not push on the film itself as it could become conical.
Push on the film core instead.
• Hold the film roll still and turn the core holder until the core holder key clicks into the key slot of the film core.
Make sure the core holder cannot turn any further.
• Release the lay-on roller arm gently so the roller rests on the outer surface of the film roll. The sides of the
roller should overlap the film roll edges, as shown in the picture below.
• Push approximately 15 cm (6”) of film into the slit at the top of the angled transfer roller. Then thread the film
around the guide roller.
• Replace and lock the feed side magazine door, being careful not to trap any film in the process.
Transfer roller
Feed side core holder
Guide roller
Lay-on roller
Step 2: The Take-up Side
The following procedures may be carried out in the light.
• Flip the magazine over lengthways so the take-up door is uppermost and the top of the magazine is facing
you. The ‘ARRI’ on the door will be upside down.
• Open the take-up side magazine door and latch back the footage counter roller arm. Fit an empty film core
to the take-up core holder.
• The film head should be protruding from the transfer roller. Check that it is cut squarely through a perforation.
• Thread the film head around the forward guide roller as indicated inside the magazine. Without touching the
film core, push the film head into the upper sprocket roller until its teeth engage in the film perforations.
• Once the sprocket teeth have engaged in the film perforations, turn the film core until the film head emerges
from the magazine throat.
ARRIFLEX 416 Quick Guide 05/2006, Page 8
Loading the 416 Magazine
Loop length mark
Rear guide roller
Magazine throat
Lower sprocket roller
Upper sprocket roller
Footage counter
roller
Forward guide
roller
Transfer roller
• Set the loop length by pulling the film head away from you and align it with the loop mark on the bottom of
the magazine (see picture above). Adjust the loop length by turning the take-up film core.
• Now take your hand off the film core – there is enough inertia in the sprockets to maintain the loop length.
• Hold the film between thumb and middle finger of your left hand, while using your index finger to push the
film head into the lower magazine throat slot. The angle at which the film enters is not as critical as it is on
SR magazines.
• Keep pushing the film in with your index finger until you see the sprockets rotate. Now take hold of the film
core again and rotate it counter-clockwise. This will pull the film from the throat into the take-up chamber.
Rear guide roller
Footage counter roller
• Thread the film around the rear guide roller following the path indicated in the magazine.
• Insert the film head into the film core (see picture right) and manually wind the core holder
two or three turns until the film winds tightly onto the core..
Correct
• Unlatch the footage counter roller arm.
• Close and lock the take-up side door.
• If using timecode, set the sensitivity switch according to the table on page 19 of this guide.
The switch is located at the top left corner of the feed side door.
Incorrect
ARRIFLEX 416 Quick Guide 05/2006, Page 9
Mounting the Magazine
Mounting the Magazine
• Insert the magazine throat into the magazine aperture in the back of the camera body and slide the
magazine forward until it locks in place.
Note: If the Shoulder Pad is attached to the camera, you will need to push down on the Shoulder Pad with your
hand or the magazine before inserting the magazine.
• Flip the silver Safety Catch on the Magazine Release Lever forward to prevent accidental release of the
magazine.
Safety Catch
Magazine
Release Lever
• Inch the camera by briefly pressing the PHASE button.
Note: When a magazine is first mounted and PHASE or RUN is pressed, the display shows ‘loop’, while the
camera performs a short routine that centralizes the film loop.
ARRIFLEX 416 Quick Guide 05/2006, Page 10
Changing Fps & Shutter Angle
The NORM and PS/CCU buttons above the display select between preset Standard Speeds and user
adjustable Programmable Speeds. Standard Speeds of 23.976, 24, 25, 29.97 & 30 fps are possible, while
the Programmable Speed can be set anywhere from 1.000 - 75.000 fps.
Note: If LOCK shows in the display, the camera settings are locked. To unlock, briefly press the LOCK button.
Setting a Standard Speed (NORM)
PS/CCU
LOCK
NORM
• Make sure the display is in mode 1 (black bar visible). If not,
repeatedly press MODE until it is. If PS/CCU shows in the
display, press NORM.
• Pressing SEL cycles through the Standard Speeds. Each speed
will flash for approximately 3 seconds.
MODE
SEL/∆
SET/ V
• While the desired speed is flashing, press SET to set the speed.
Display in mode 1.
Speed set at 24.000 fps
Setting a Programmable Speed (PS/CCU)
• Press PS/CCU to switch from NORM to PS/CCU.
• Press MODE once to switch the display from mode 1 to mode 2.
• Pressing SEL selects one digit after another. The selected digit
will flash.
Display in mode 2.
Speed set at 75.000 fps
• Press SET to increment the value of the flashing digit by 1.
• Repeat the last 2 steps for all the digits that need to be changed.
Final confirmation of the set speed is not necessary.
Checking the Mirror Shutter Angle
• With the camera in Standby, press and hold PHASE. The
camera will inch at approximately 1 fps.
• After 2 seconds the top line of the display shows the open
angle of the mirror shutter, while the bottom line will show the
supply voltage
Display with PHASE button
pressed. Open mirror shutter
angle 172.8º and supply of
voltage 26.9.
Changing the Mirror Shutter Angle
Note: Before adjusting the mirror shutter, check that it is in the
viewing position then turn off the camera and remove the
battery or power cable! Accidentally running the camera
during adjustment would cause catastrophic damage!
416 Shutter Tool
Mirror Shutter centre
• Remove the lens or lens port cavity cap and hold the mirror
shutter still by lightly pressing your finger on its black centre
area. Do NOT touch the reflective surface.
• Insert the 416 Shutter Tool into the adjustment hole below the
mirror centre.
• Turn the 416 Shutter Tool until the desired Mirror Shutter preset
angle is reached. Angle presets are: 180º, 172.8º, 150º, 144º,
135º, 90º & 45º. Turning counter-clockwise reduces the angle.
ARRIFLEX 416 Quick Guide 05/2006, Page 11
Beeper, Backlight & RGB ARRIGLOW
Beeper
The 416 is equipped with a beeper which can sound when the camera is started
or stopped. The upper line of display mode 6 allows the user to decide whether
and when the beeper sounds and how loud (LS is shown for ‘loudspeaker’). The
left-hand bar shows the status of the start beep. The right-hand bar shows the
status of the stop beep. In each case, with the bar in the high position the beep
will sound, in the low position it will not. The final digit is the volume, which is
adjustable between 0 (off) and 3.
Backlight
The lower line of display mode 6 controls the brightness of the control buttons
backlight. This can be set between 0 (off) and 3.
Changing the Beeper and Backlight settings
• Use the SEL button to select the digit you wish to change, which will flash.
• Use the SET button to change the value of the flashing digit.
RGB ARRIGLOW
The ARRIGLOW on the 416 gives the user a choice of frameglow colours.
Colours 1 – 8 are preset colours followed by U, which is user adjustable by
setting individual Red, Green and Blue values. The ARRIGLOW brightness is
adjusted with the + and – buttons above the camera display.
Changing the RGB ARRIGLOW colours
• Push the “+” DIMMER button on the camera left side so you can see the
ARRIGLOW in the viewfinder.
• Set the display to mode 7.
• Pushing the SEL button will make the ARRIGLOW number flash. Pushing the
SET button will now cycle through preset colours 1 – 8 and then user
adjustable colour “U”. Stop at the colour you like – no confirmation is
necessary.
• To change the user adjustable colour, push SEL again while U is flashing. The
SEL button will now cycle through the red (r), green (G) and blue (b) values of
the user colour. Pushing the SET button changes the flashing colour value from
0 (no colour) up to 16 (maximum colour).
ARRIFLEX 416 Quick Guide 05/2006, Page 12
On-board Battery
On-Board Battery OBB-2
The OBB-2 On-Board Battery attaches directly to the camera body by means of a quick change mechanism
that can be easily operated with one hand. The OBB-2 incorporates a built-in power meter to indicate the state
of charge, while an extra contact in the power connector communicates this information to the camera. When
an OBB-2 is connected, display mode 3 can additionally show battery capacity or magazines left.
Note: The new 416 power connector on the camera remains compatible with standard ARRI 24 volt power cables.
Mounting the OBB-2
• Fit the power plug of the OBB-2 into the camera power connector and slide the battery forward.
Removing the OBB-2
• Hold the OBB-2 as shown in the picture below and press the on-board battery release button.
• Pull the battery backwards until the power connectors disengage.
On-board Battery
Battery power meter
release button
On-board Battery
ARRIFLEX 416 Quick Guide 05/2006, Page 13
Integrated Video System
Flicker free
on/off button
White balance
button
Manual Gain
Control button
ENTER/INSERT
button
UP button
RIGHT button
LEFT button
MINI
MONITOR
connectors
DOWN button
Left/right
adjustment
Image rotation
ON–OFF–CHECK/
HIDE MENU switch
Up/down
adjustment
Focus
adjustment
Video out with
data or Y–signal
Clean Video out (no
data) or C–signal
Video lens IRIS
ON–OFF–CHECK/HIDE MENU switch
Make sure that the camera power is ON. Move the ON–OFF–CHECK/HIDE MENU switch to ON (centre position).
To display a summary of all menu choices while the on-screen menu is not visible, press the ON–OFF–CHECK/
HIDE MENU switch all the way to the left (it will spring back to the centre position).
To temporarily hide the on-screen menu while it is visible, press the ON–OFF–CHECK/HIDE MENU switch all
the way to the left. This is useful to check the image while making adjustments in the on-screen menu.
White balance
Press the WB button to cycle through the five white balance settings. Four of these, AUTO, INDOOR,
OUTDOOR & MANUAL, have dedicated LEDs. The fifth setting, ONE PUSH WHITE, is available when the
ENTER/INSERT LED flashes.
AUTO
automatic white balance.
INDOOR 3200 K
OUTDOOR 5600 K
MANUAL
when the illumination is tungsten and no colour correction filter is used.
when the illumination is daylight or HMI and no colour correction filter is used.
manual white balance as controlled by the UP (increase blue), DOWN (decrease
blue), RIGHT (increase red) & LEFT (decrease red) buttons.
ONE PUSH WHITE
user adjustable – hold a white card in front of the lens and press ENTER/INSERT.
Controlling image brightness
Open the video lens IRIS fully and use either Automatic Gain Control or Manual Gain Control to control the
image brightness. Only use the video lens IRIS if the brightness exceeds the electronic control range.
ARRIFLEX 416 Quick Guide 05/2006, Page 14
Integrated Video System
Automatic Gain Control
• Press the MGC button to toggle between Manual Gain Control (LED on) and Automatic Gain Control (LED off).
• When MGC is off, Automatic Gain Control will adjust the image brightness.
Manual Gain Control
• Press the MGC button to toggle between Manual Gain Control (LED on) and Automatic Gain Control (LED off).
• When MGC is on, adjust the image gain with the UP (increase gain) & DOWN (decrease gain) buttons.
The on-screen menu
The on-screen menu allows the adjustment or selection of the following features: Load & store settings, White
Balance, Gain, Colour Bars, video settings, Format Markings, Image Compare/Store, Text Inserter (camera
status, system status, user text, timecode & more) & VITC/WHITELINE.
• To display the main menu, press and hold the ENTER/INSERT button for 3 seconds.
• To select a sub-menu, use the UP & DOWN buttons. The arrow indicates which sub-menu is selected.
• To enter the selected sub-menu, press the RIGHT button.
• To go back to the main menu chose EXIT, which can be found at the bottom of each screen.
• To leave all menus, press and hold the ENTER/INSERT button for 3 seconds.
BNC mode
• Enter the VIDEO/TEXT ADJ sub-menu to chose between VBS (composite) and Y/C video signals to be output
by the video out (BNC) connectors under the BNC OUT option.
VBS
Left BNC:
Right BNC:
composite video with on-screen data.
composite video without on-screen data.
Y/C
Left BNC:
Right BNC:
Y (luminance) portion of the video signal.
C (chrominance) portion of the video signal.
How to get on-screen data in Y/C mode
• With Y/C selected in the VIDEO/TEXT ADJ sub-menu, the option of Y/C DATA, can now be toggled
between ON or OFF. If ON is selected then the Y/C signal will have on-screen data.
How to get black & white video
• Set the BNC mode to Y/C.
• Connect the video cable to the left video out (BNC) connector only.
How to adjust electronic sharpness
The 416 IVS has an electronic sharpness control which can be adjusted to optimize the look of the video output.
• Press and hold the ENTER/INSERT button for 3 seconds to enter the on-screen menu.
• In the VIDEO/TEXT ADJ sub-menu, adjust the value assigned to SHARPNESS for the best looking picture.
• To leave the on-screen menu, press and hold the ENTER/INSERT button for 3 seconds.
How to generate colour bars
To assist in setting up attached video monitors, the 416 IVS has the option to generate colour bars.
• Press and hold the ENTER/INSERT button for 3 seconds to enter the on-screen menu.
• In the WB/GAIN/BARS sub-menu, set COLOR BARS to ON.
ARRIFLEX 416 Quick Guide 05/2006, Page 15
Accessories
ARRIFLEX 416 Quick Guide 05/2006, Page 16
Accessories
ARRIFLEX 416 Quick Guide 05/2006, Page 17
Timecode Operation
Note: To write SMTPE timecode to film, ARRIFLEX 416 magazines must have the 416 Timecode Module fitted.
Note: Timecode recording is only possible at the 5 Standard Speeds of 23.976, 24, 25, 29.97 & 30 fps.
Turning Timecode Recording On and Off.
• Press the MODE key until the display shows mode 4.
• Press and hold SET until the TC symbol appears (or disappears)
on the display.
• Alternatively, Timecode recording is automatically turned on when
Display in mode 4. TC
the camera receives a valid Timecode signal (see Timecode Input).
is on. Framerate is 25 fps
Timecode Input (Jam Syncing)
• Connect the LTC signal from a Timecode generator (or motherclock) to the Timecode connector on the
camera’s right side.
• The last 2 digits on the display will show ‘EC’ (external code). When the Timecode is correctly transferred
they will change to ‘CC’ (correct code).
• After approximately 10 seconds the last 2 digits will change to the Timecode recording framerate.
Note: If the motherclock is left connected for 10 minutes, the camera’s Timecode clock will synchronize itself to the
exact frequency of the motherclock leading to better accuracy and extended periods between jam syncing.
Userbit Input
• Userbits are automatically input with the Timecode, but they can
also be set by means of the camera display in mode 5.
• Use the SEL button to select the digit you wish to change, which will flash.
• The SET button changes the value of the flashing digit.
Display in mode 5.
Showing Userbits
• Repeat the last two steps for all the digits that need to be changed.
Note: Userbit values are hexadecimal so only values from 0 – 9 and A – F are available.
Magazine Timecode Sensitivity Switch
To ensure proper timecode exposure on film, the intensity of the exposure LED in the 416 Timecode Module is
adjustable. Magazines have a Timecode Sensitivity Switch in the top left corner of the feed side door for this
purpose. Different film stocks require the TCS Switch to be set to different TCS numbers. The table on the next
page shows the settings required by current film stocks (as of November 2005).
Timecode sensitivity
switch
DIMMER
—
+
NORM
PS/CCU
LOCK
MODE
SEL/∆
SET/ V
ARRIFLEX 416 Quick Guide 05/2006, Page 18
Timecode Sensitivity Table
16 mm Kodak Film Stocks
(Color Negative)
16 mm Fuji Film Stocks
Kodak 7201
Kodak 7205
Kodak 7212
Kodak 7217
Kodak 7218
Kodak 7222
Kodak 7229
Kodak 7231
Kodak 7236
Kodak 7239
Kodak 7240
Kodak 7245
Kodak 7246
Kodak 7248
Kodak 7250
Kodak 7251
Kodak 7274
Kodak 7276
Kodak 7277
Kodak 7278
Kodak 7279
Kodak 7284
Kodak 7287
Kodak 7289
Kodak 7293
Kodak 7296
Kodak 7297
Kodak 7298
Kodak 7620
TCS 7
TCS 6
TCS 6
TCS 6
TCS 5
TCS 8
TCS 5
TCS 9
TCS 6
TCS 5
TCS 6
TCS 6
TCS 6
TCS 6
TCS 5
TCS 4
TCS 6
**
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
8428
8622
8632
8652
8653
8653
8662
8663
8672
8673
8682
8683
8692
(Color Reversal)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
TCS 6
TCS 6
TCS 6
TCS 5
TCS 6
TCS 6
TCS 4
TCS 5
TCS 4
TCS 5
TCS 6
TCS 6
TCS 4
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(B/W Negative)
(Color Negative)
(B/W Negative)
(Color Negative)
(Color Reversal)
(Color Reversal)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Reversal)
(Color Reversal)
(Color Negative)
(B/W Reversal)
(Color Negative)
(B/W Reversal)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
(Color Negative)
** - Timecode exposure not possible.
TCS 5
**
TCS 4
TCS 5
TCS 6
TCS 5
TCS 5
TCS 5
TCS 6
TCS 5
TCS 6
ARRIFLEX 416 Quick Guide 05/2006, Page 19
ARRI Group Addresses
Australia
Canada
ARRI Australia PTY Limited (Sales, Service & Rental)
Unit 6C, 5 Talavera Road, Macquarie Park, Sydney. NSW 2113, Australia
Voice phone: +61 (2) 9855 4300, FAX: +61 (2) 9855 4301
Email: [email protected]
ARRI Canada Limited (Sales & Service)
415 Horner Ave. Unit 11, Toronto, Ontario M8W 4W3, Canada
Voice phone: +1 (416) 255 3335, FAX: +1 (416) 255 3399
Email: [email protected]
Germany
Arnold & Richter Cine Technik (Sales & Service)
Türkenstraße 89, D-80799 Munich, Germany
Voice phone: +49 (0)89 3809-0, FAX: +49 (0)89 3809-1245
Email: [email protected]
ARRI Camera Rental (Film Equipment Rental)
Türkenstraße 89, D-80799 Munich, Germany
Voice phone: +49 (0)89 3809-1240, FAX: +49 (0)89 3809-1798
Email: [email protected]
Great Britain
ARRI GB Limited (Sales & Service)
2 Highbridge, Oxford Road, Uxbridge, Middlesex, UB8 1LX, England
Voice phone: +44 (0)1895 457 000, FAX: +44 (0)1895 457 001
Email: [email protected]
ARRI MEDIA (Film Equipment Rental)
3 Highbridge, Oxford Road, Uxbridge, Middlesex, UB8 1LX, England
Voice phone: +44 (0)1895 457 100, FAX: +44 (0)1895 457 101
Email: [email protected]
ARRI Lighting Rental (Lighting Rental)
4 Highbridge, Oxford Road, Uxbridge, Middlesex, UB8 1LX, England
Voice phone: +44 (0)1895 457 200, FAX: +44 (0)1895 457 201
Email: [email protected]
Italy
USA
ARRI Italia S.r.l. (Head Office, Milan)
Viale Edison 318, 20099 Sesto San Giovanni (Milan), Italy
Voice phone: +39 (02) 262 271 75, FAX: +39 (02) 242 1692
Email: [email protected]
ARRI Italia S.r.l. (Sales & Service, Rome)
Via Placanica 95, 00040 Morena (Rome), Italy
Voice phone: +39 (06) 726 707 97, FAX: +39 (06) 723 1541
E-mail: [email protected]
ARRI Inc. (Sales & Service, East Coast)
617 Route 303, Blauvelt, NY 10913-1123, USA
Voice phone: +1 914 353 1400, FAX: +1 914 425 1250
Email: [email protected]
ARRI Inc. (Sales & Service, West Coast)
600 North Victory Blvd., Burbank, CA 91502-1639, USA
Voice phone: +1 818 841 7070, FAX: +1 818 848 4028
Email: [email protected]
ARRI CSC (Film Equipment Rental, NY)
619 West 54th St, New York, NY 10019, USA
Voice phone: +1 212 757 0906, FAX: +1 212 713 0075
Email: [email protected]
ARRI CSC (Film Equipment Rental, Florida)
2385 Stirling Road, Fort Lauderdale, FL 33312, USA
Voice phone: +1 954 322 4545, FAX: +1 954 322 4188
Email: [email protected]
Website:
ARRIFLEX 416 Quick Guide 05/2006, Page 20
|