XEROX WIDE FORMAT COPY SYSTEM 8825, 8830,8850,
510 Series, 721P & X2 TECH
XEROX WIDE FORMAT
COPY SYSTEM User
Guide
AccXES Firmware Version 10.0
Contents
Getting to know the WIDE FORMAT COPY SYSTEM
1
Getting to know the WIDE FORMAT COPY SYSTEM.............................................................1
Scanner standard components.............................................................................................3
Scanner compact components.............................................................................................7
Scanner Control Panel..........................................................................................................9
Media Selection........................................................................................................ 10
Image Quality Area ................................................................................................... 13
Background Suppression .......................................................................................... 17
Copy ........................................................................................................................ 18
Reduce/Enlarge........................................................................................................ 19
Graphical Display and Navigation Keys...................................................................... 21
Numeric Keypad and Special Features/Control Keys................................................... 23
Special Features Keys .............................................................................................. 24
Scan Control Keys.................................................................................................... 24
The Printer and the Controller............................................................................................ 25
Powering On the WIDE FORMAT COPY SYSTEM ............................................................... 25
Initial power-on ......................................................................................................... 25
Switching on the Scan System................................................................................... 26
Switching on the Controller and the Printer (XEROX WIDE FORMAT COPY SYSTEM
8825/8830/8850) ...................................................................................................... 26
Switching on the HFT Controller and the Printer (XEROX WIDE FORMAT
8825/8830/8850/510 Series/721P)............................................................................. 28
Switching on the Printer and the Controller (X2 TECH)................................................ 29
Scanner Warm-up..................................................................................................... 29
Powering off the System..................................................................................................... 30
Document quality
31
Document quality................................................................................................................ 31
Dynamic Background Removal........................................................................................... 31
Automatic edge detection and document centering ..................................................... 32
Determining document quality............................................................................................ 33
What is a good quality document? ............................................................................. 33
What is a bad quality document?............................................................................... 33
Preparing documents ......................................................................................................... 34
Scanning strategies............................................................................................................ 35
Image Quality
37
Original, Type ..................................................................................................................... 38
COPY MODE ....................................................................................................................... 38
Type, Normal, Line, Photo, ........................................................................................ 38
SCAN MODE ....................................................................................................................... 40
Type, Normal............................................................................................................ 40
Type Line................................................................................................................. 41
XEROX WIDE FORMAT COPY SYSTEM
Contents · i
Type Photo............................................................................................................... 42
Type, Color .............................................................................................................. 43
Background Suppression ................................................................................................... 45
Copy ................................................................................................................................... 45
Making copies
47
Making copies..................................................................................................................... 47
Controlling the scan .................................................................................................. 47
Image Quality........................................................................................................... 49
Making a copy with the default settings.............................................................................. 50
Making a copy the same size as the original document...................................................... 51
Fitting the image to a fixed copy size ................................................................................. 52
Scanning when using a Folder
53
Scanning when using a Folder........................................................................................... 53
Ready to Copy Finisher Screen ................................................................................. 54
Scanning oversized documents
55
Scanning oversized documents.......................................................................................... 55
LONG DOCUMENTS............................................................................................................ 55
WIDE DOCUMENTS ............................................................................................................ 55
Special features keys
56
Special features keys.......................................................................................................... 56
Printer Interrupt key............................................................................................................ 57
Store/Recall key.................................................................................................................. 58
Last Job ................................................................................................................... 58
Job Templates.......................................................................................................... 60
Save Default Template.............................................................................................. 64
Recall Factory Defaults............................................................................................. 64
Finisher key........................................................................................................................ 65
Finisher menu options............................................................................................... 66
Sets Build key..................................................................................................................... 69
Preparing to build the set........................................................................................... 69
Building and printing the set ...................................................................................... 69
Batch key............................................................................................................................ 71
Transform key..................................................................................................................... 72
Margins.................................................................................................................... 72
Justification.............................................................................................................. 74
Transform ................................................................................................................ 75
Sample key......................................................................................................................... 77
Copy Mode Sample: ................................................................................................. 77
Scan Mode Sample:.................................................................................................. 78
Scanning to the Network (SCAN mode)
81
Scanning to the Network (SCAN mode).............................................................................. 81
Switching between COPY mode and SCAN mode .............................................................. 82
Understanding the READY TO SCAN screen...................................................................... 83
Selections disabled in SCAN mode .................................................................................... 83
Operating in SCAN mode.................................................................................................... 84
Clearing the scanned images ............................................................................................. 86
Managing the file system.................................................................................................... 86
ii · Contents
XEROX WIDE FORMAT COPY SYSTEM
Main Menu
88
Main Menu .......................................................................................................................... 88
Configuration menu............................................................................................................ 89
LOCALIZATION........................................................................................................ 90
CONTROL PANEL ................................................................................................... 91
COPY OPTIONS ...................................................................................................... 92
IMAGE ENHANCEMENTS ........................................................................................ 97
TIMERS ................................................................................................................... 98
POWER SAVER....................................................................................................... 99
SCANNER CONTROL ............................................................................................ 100
System Information menu................................................................................................. 103
SYSTEM DESCRIPTION ........................................................................................ 103
RECENT FAULT LIST ............................................................................................ 105
CONFIGURATION PRINTS .................................................................................... 106
System Administration menu ........................................................................................... 108
Entering the system administration password ........................................................... 108
JOB ACCOUNTING................................................................................................ 109
FILE SYSTEM........................................................................................................ 109
CHANGE PASSWORD........................................................................................... 113
SECURITY SETTINGS ........................................................................................... 114
Diagnostics menu............................................................................................................. 115
USAGE METERS ................................................................................................... 116
CLEAR SCANNER USAGE..................................................................................... 116
SCANNER DIAGNOSTICS ..................................................................................... 117
PASSWORD .......................................................................................................... 132
Job Accounting
133
Job Accounting ................................................................................................................ 133
Overview........................................................................................................................... 133
Job Accounting Mode menu............................................................................................. 134
Submitting jobs ................................................................................................................ 134
From the Scanner Control Panel.............................................................................. 135
Over the network .................................................................................................... 136
Terminating use under an account ........................................................................... 136
Cleaning and maintenance - Scanner
137
Cleaning and maintenance - Scanner............................................................................... 137
Cleaning the Platen Glass and Document Drive Rolls...................................................... 138
Cleaning the Calibration Strip........................................................................................... 139
Problem solving
140
Problem solving................................................................................................................ 140
Specifications
145
Specifications................................................................................................................... 145
Appendices
147
Appendix 1........................................................................................................................ 147
Appendix 2........................................................................................................................ 148
Appendix 3........................................................................................................................ 149
Appendix 4........................................................................................................................ 149
XEROX WIDE FORMAT COPY SYSTEM
Contents · iii
Appendix 5........................................................................................................................ 151
Appendix 6........................................................................................................................ 151
Appendix 7........................................................................................................................ 152
iv · Contents
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE
FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT
COPY SYSTEM
This manual contains operating instructions for the user and the system
administrator for the XEROX WIDE FORMAT COPY SYSTEM
8825/8830/8850/510 Series and 721P with version 10.0 AccXES
firmware loaded into the Controller.
Your XEROX WIDE FORMAT COPY SYSTEM is an integrated solution
for electronically scanning and then printing images for engineering or
architectural use. The WIDE FORMAT COPY SYSTEM consists of the
WIDE FORMAT SCAN SYSTEM and Control Panel for capturing
images, the Controller for processing these images, and XEROX WIDE
FORMAT COPY SYSTEM 8825, 8830, 8850, 510 Series, 721P or
XEROX WIDE FORMAT X2 TECH Printers for making good quality
copies of the captured images in engineering or architectural sizes.
Table 1 below shows the various WIDE FORMAT COPY SYSTEM
configurations. An optional Online Folder is available for each of these
configurations to provide further processing of the printed output.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 1
Table 1. WIDE FORMAT COPY SYSTEM configurations
Scanner
Printer
Controller
Product Code
WIDE FORMAT SCAN SYSTEM
WIDE FORMAT SCAN SYSTEM
WIDE FORMAT SCAN SYSTEM
WIDE FORMAT SCAN SYSTEM
WIDE FORMAT SCAN SYSTEM
WIDE FORMAT SCAN SYSTEM
XEROX WIDE FORMAT 8825
XEROX WIDE FORMAT 8830
XEROX WIDE FORMAT 8850
XEROX WIDE FORMAT X2 TECH
N5T, EV4
N5T, CNG
CNG, HFT
HFT, KLF
XEROX WIDE FORMAT 510 Series HFT, PUN
XEROX WIDE FORMAT 721P HFT, PUN
The WIDE FORMAT COPY SYSTEM has two modes of operation -
COPY and SCAN. In the COPY mode, documents are scanned,
temporarily stored in memory or on the Controller hard disk, and then
sent to the local Printer as soon as the Printer is available. In the SCAN
mode, documents are scanned and then stored on the Controller hard
disk for later retrieval over a network by a remote device. The WIDE
FORMAT COPY SYSTEM allows concurrent printing, copying, and
scanning to the network, so there is no need to wait for the Printer to
finish before scanning the next document.
NOTE: The XEROX WIDE FORMAT X2 TECH and Synergix Digital X2
TECH Solution does not support copying at this time.
The XEROX FORMAT COPY SYSTEM contains Dynamic Background
Suppression technology. Dynamic Background Suppression examines a
sample of the document intelligently and makes automatic image quality
adjustments that yield a good copy even from poor original documents.
The document width is automatically detected and the centering of a
scanned original for most opaque documents is adjusted. Translucent
documents (transparencies, clear film, etc.) in most cases will not be
detected.
A new Productivity feature introduced with version 10.0 firmware and
requires a new WIDE FORMAT SCAN SYSTEM with a new Document
Feed-in Tray. Sensors built into the Feed Tray measure the document
width without doing a prescan, which increase the document and copy
throughput thereby increasing productivity.
For documents that require additional adjustments to obtain the best
copy quality, a variety of image quality and reduction/enlargement
settings are available. All of these functions are controlled from the
Scanner Control Panel. This Control Panel, which is mounted on top of
the Scanner, receives all power and information from the Scanner.
2 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Scanner standard components
The illustrations below show the components of the WIDE FORMAT
SCAN SYSTEM. These components are standard on the XEROX WIDE
FORMAT COPY SYSTEM 8825, 8830, 8850,510 Series. And X2 TECH.
The Stand is standard or optional on the 8850. With the exception of the
Stand and Standard Organizer, the components are standard on the
721P. Following the illustrations are descriptions of each of the
components.
WIDE FORMAT SCAN SYSTEM Front View
A: Document Handler
D: Stand
B: Scanner Control Panel
C: Thick Document Lever
E: Standard Organizer
F: Document Feed-in Tray
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 3
WIDE FORMAT SCAN SYSTEM Front View
B
A
C
F
D
A: Document Handler
D: Stand
E: Productivity Document Feed-in Tray
B: Scanner Control Panel
C: Thick Document Lever
A. Document Handler
Raise the Document Handler for routine maintenance functions and to
access the optical paper sensors for diagnostic routines.
B. Scanner Control Panel
The control panel allows the selection of options and features and
contains a graphical display for the communication of information and
instructions. Refer to Scanner Control Panel for additional information.
C. Thick Document Lever
The Thick Document Lever is used to adjust the Scanner for thick
documents and to remove documents from the Scanner feed
mechanism. When setting the thickness for a document, raise the lever
to the next thickness. If the document slides past the Feed Rolls into the
Document Handler, lower the Lever to the next position.
D. Stand
The Stand is standard with the XEROX WIDE FORMAT COPY
SYSTEM8825, 8830.and 8850, and optional with the 721P. The Stand is
also standard with the WIDE FORMAT COPY SYSTEM 510dp Series.
4 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
E. Standard Organizer
The Organizer is located on the front of the Scanner. It is useful for
holding multiple documents that are to be scanned. It has two
extensions at its end that can be pulled out to accommodate longer
documents (up to size E or A0).
F Document Feed Tray
Insert documents to be scanned face down and centered into the
Document Feed Tray.
F. Productivity Document Feed Tray
Provides built-in Document Width Sensors that eliminate the need to
prescan document to do width measurement. This increases the
document throughput resulting in higher productivity with a WIDE
FORMAT COPY SYSTEM. This option is only available on the newer
WIDE FORMAT SCAN SYSTEM.
.
Rear View
A: Standard Stacker
B: Document Exit Slot
C: Power On/Off switch
D: Power Cord and Connector
E: Status Indicator LED
F: IEEE 1394 Cable and Connector
NOTE: Components shown above with the exception of the Standard
Organizer are also available on all WIDE FORMAT SCAN SYSTEMs
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 5
A. Standard Stacker
The Stacker is located at the rear of the Scanner. When the
AUTORETURN feature is set to REAR, documents exit the Scanner onto
the Stacker. The Stacker can be adjusted to any one of four positions by
raising or lowering it. The height of the Stacker should be adjusted to
accommodate the document being scanned. It has two extensions at its
end that can be pulled out to accommodate longer documents (up to size
E or A0). When scanning most common weight (20 lb, 80gsm)
documents, move the Stacker to the 2nd rung from the bottom.
NOTE: All thick documents and documents over 36 inches (914 mm)
exit from the rear of the Scanner (regardless of the AUTORETURN
setting). When scanning thick documents, the Stacker must be set to the
lowest position for optimum performance.
B. Document Exit Slot
When the DOCUMENT RETURN feature is set to REAR, documents exit
the Scanner through this slot and are delivered to the rear Stacker.
C. Power On/Off Switch
This switch turns the Scanner on and off. Press this switch to the on (I)
position to turn on the Scanner and to the off (O) position to turn off the
Scanner.
D. The Power Cord supplies power to the Scanner. Plug one end of the
cord into the Scanner and the other end into an electrical outlet.
E.Status LED
The digital status LED provides an indication of the condition of the
scanner and communications with the controller. A P displayed on the
LED Display on the rear of the scanner indicates that the scanner is
operating normally and has established communications with the
controller.
F. IEEE 1394 Cable and Connector
The IEEE 1394 Cable is the communications link between the Scanner
and the Controller. Plug one end of the cable into either one of the IEEE
1394 connections at the rear of the Scanner. Plug the other end into the
IEEE 1394 connection on the Controller.
6 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Scanner compact components
The illustrations show the optional compact Stacker and organizer that
are available for the WIDE FORMAT SCAN SYSTEM. The compact
components allow the XEROX WIDE FORMAT COPY SYSTEM to be
installed in sites where space requirements are at a premium.
Front View
A: Compact Organizer
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 7
Rear View
A: Compact Stacker
8 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Scanner Control Panel
The Scanner Control Panel is divided into three sections:
·
The options keys section, which contains the - Media Selection,
Image Quality, and Reduce/Enlarge options selections
·
·
The graphical display and the navigation keys section.
The right-hand section, which contains the numeric keypad, the
special features keys, and the scan control keys.
If the BEEP function is enabled (factory default), a beep sound will be
heard when a key is pressed. If an improper key is pressed, a multiple
beep sound will be heard.
A: Option Keys section
D: Numerical Key pad
E: Special Features keys
F: Navigation keys
B: Graphical Display
C: Scan Control keys
The left side of the Scanner Control Panel contains the keys for the
selection of options. It is divided into three areas - Media Selection,
Image Quality, and Reduce/Enlarge.
OPTIONS KEYS
To select an option, press the key(s) beneath the option. In some cases,
a screen requiring a selection or input is displayed on the graphical
display. When an option is selected, the indicator lamp to the left of the
option illuminates.
The illustration below depicts the options portion of the Scanner Control
Panel.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 9
Control Panel Options Area
The Media Selection area of the Scanner Control Panel allows you to
select the media Source, Type, and Output Format. The illustration
below depicts the Media Selection portion of the control panel.
Media Selection
10 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Source
The Source option allows you to select the source of the media on which
the image will be printed. To select the media source, press the key
beneath the Source settings until the desired source indicator lamp
illuminates.
The Source settings are:
·
Sheet - This setting tells the Printer to print from a manually
inserted sheet of media.
·
R4 - This setting is applicable to the WIDE FORMAT COPY
SYSTEM 721P only. When it is selected on the WIDE FORMAT
COPY SYSTEM 721P, both the R1 and R3 indicator lamps
illuminate and the Printer selects the media stored on Roll 4.
·
R3 - This setting is applicable to the, WIDE FORMAT COPY
SYSTEM, 8850, 721P, and WIDE FORMAT 510 Series (3
Drawer) only. When it is selected on those systems, the R3
indicator lamp illuminates and the Printer selects the media
stored on Roll 3.
·
·
·
R2 - This setting tells the Printer to select the media stored on
Roll 2.
R1 - This setting tells the Printer to select the media stored on
Roll 1.
Auto (factory default) - This setting automatically selects the roll
containing the media that best fits the size of the captured
image. For most documents, the Scanner is able to
automatically detect the width of the scanned document. This
permits the Auto function to automatically select the most
appropriate roll of media.
NOTE: Roll 2 and sheet feed are optional on XEROX WIDE FORMAT
8825. Roll 2 and 3 are optional on the XEROX WIDE FORMAT 510dp
Series. If these options are not installed, they cannot be selected. To
print from a cut sheet, Sheet mode must be explicitly selected. The Auto
mode cannot select a cut sheet.
Type
The Type option allows you to select the kind of media on which to print -
Bond, Vellum/Tracing, or Film. To select the media type, press the key
beneath the Type settings until the desired type indicator lamp
illuminates.
NOTE: Only media types actually loaded into the Printer can be
selected. When a roll is selected, the media type for that roll is
automatically selected also. If more than one media type is loaded when
the media source is set to Auto, the default choice priority is Bond (first),
Vellum (second), and Film (third). Refer to the applicable Printer
Operator Manual for instructions about how to load rolls and specify the
width and media type.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 11
Output Format
The Output Format option allows you to select the size to which the roll
feed media will be cut. It has three modes - Manual, Preset, and
Synchro.
Manual
Manual allows you to enter the desired length and width manually.
To select the Manual mode:
1. Press the key beneath Output Format until the Manual indicator
lamp illuminates. The CUSTOM OUTPUT FORMAT screen is
displayed.
NOTE: If the indicator lamp is already lit, press the key once to display
the screen.
CUSTOM OUTPUT FORMAT
ENTER CUSTOM MEDIA SIZE:
WIDTH (11.0 -36.0):
11.0 IN
8.5 IN
LENGTH (8.3 – 1200.0):
2. Press the Previous or Next key to select WIDTH or LENGTH.
3. Press the Enter key to confirm the choice.
4. Use the numeric keypad to enter the desired value.
NOTE: The entered value must be within the limits shown in
parentheses on the screen.
5. Press the Enter key to confirm the value.
6. Repeat steps 3 to 5 to enter the value for the remaining setting.
7. When the values for WIDTH and LENGTH are correct, press the
Exit key to return to the READY screen.
Preset
Preset allows you to select a predefined length to which the roll media
should be cut during printing. The associated width specification will
depend on the Media Source selection. If the Media Source selection
is set to Auto, the system will select the roll of media that best matches
the width specification. If Media Source is set to R1, R2, R3, or R4; the
system will use the selected roll regardless of the width specification.
To select the Preset mode:
1. Press the key beneath Output Format until the Preset indicator
lamp illuminates. The PRESET OUTPUT FORMAT screen is
displayed.
NOTE: If the indicator lamp is already lit, press the key once to display
the screen.
12 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
PRESET OUTPUT FORMAT
8.5 X 11 ANSI A
SELECT:
2. Press the Previous or Next key to select an item from the list.
NOTE: Formats can be added or removed from this list. Refer to
"Custom Media Formats" in the "Main Menu" section for more
information.
3. Press the Enter key to confirm the choice and return to the
READY screen.
Synchro
When the Synchro mode is selected, the length of the original is
measured as it passes through the Scanner and automatically cuts the
media at the Printer to match the length of the original document.
Synchro is the factory default. To select the Synchro mode, press the
key beneath Output Formats until the Synchro indicator lamp
illuminates.
The Image Quality area of the Scanner Control Panel allows you to
make corrective adjustments to the image and extract the best possible
copy quality from an original document. It contains the Type,
Background Suppression, and Copy options.
Image Quality Area
The illustrations below depict the Image Quality portion of the Control
Panel for AccXES software version 10.0 and SCAN SYSTEM firmware
version 3.2.5 or higher.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 13
The SCAN SYSTEM firmware must be at version 3.0.9 or greater to
support Normal, Line, Photo, or Color Type. If the SCAN SYSTEM is
not at the required version an error message. Depending on what Mode
is selected (COPY or SCAN) the message will be displayed as show
below.
INVALID MODE
UPGRADE SCANNER FIRMWARE
AUTO
1
100.0 %
INVALID MODE
UPGRADE SCANNER FIRMWARE
TIFF/CCITTG4
1 BIT
400 DPI
14 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Original, Type
The Type option allows you to specify the type classification of your
document. To select the document type, press the key beneath the
Type settings until the desired Type indicator lamp illuminates.
Normal — (factory default) Select Normal for most copying needs. This
setting will provide good image quality for copying most types of
drawings. Shaded areas will be preserved.
Normal
In the SCAN mode, the following screen is displayed when the Normal
key is pressed.
SCAN OPTIONS (NORMAL)
PREVIEW
FILE FORMAT:
TIFF
Line — Select Line for an image containing text, line art, or a mixture of
these. If the Mode selected is SCAN, and the Scan to Net Feature Key is
installed, the SCAN OPTION (LINE) screen will be displayed. If the
COPY mode is selected the READY TO COPY screen will be displayed.
Refer to the "Image Quality" section of this manual for additional
information.
Line
SCAN OPTIONS (LINE)
PREVIEW
TIFF
FILE FORMAT:
Photo — Select Photo when the document contains a gray scale or
color image, such as a photograph. If the Copy mode is selected the
READY TO COPY screen will be displayed. In Scan Mode, the following
screen will be displayed. Refer to the Image Quality section of this
manual for additional information.
Photo
SCAN OPTIONS (PHOTO)
PREVIEW
ü
COMPRESSION:
RAW
TIFF
FORMAT:
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 15
NOTE: The Background Suppression option cannot be used with the
Photo setting. If Photo is selected, Background Suppression is
automatically set to Off.
Color
Color — Select Color when scanning full color documents. When Color
Type is selected a version of the following screens will be displayed. The
content of the screen will depend on the selected FORMAT and
COMPRESSION.
The following screens will only be displayed in SCAN mode when the
Scan to Net and Color Scanner feature keys are installed. The Normal
and Photo LED's will be lit when Color is selected.
The selections that appear on the screen depend on the FORMAT and
COMPRESSION selections.
SCAN OPTIONS (COLOR)
: TIFF
PREVIEW
FORMAT:
: PACKBITS
COMPRESSION:
SCAN OPTIONS (COLOR)
PREVIEW
: TIFF
FORMAT:
INDEX
COMPRESSION:
PALETTE:
DEFAULT
SCAN OPTIONS (COLOR)
PREVIEW
JPEG
FORMAT:
NORMAL
ü
COMPRESSION:
16 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Background Suppression
Background
Suppression
The Background Suppression option enables you to make adjustments
for documents that contain poor contrast between the foreground image
and the background.
Four Background Suppression choices are provided:
Off
This setting disables Background Suppression. All the
characteristics of the original document with minimum alteration are
reproduced on the copy. Choose this selection when:
·
·
·
The lead edge of the document is very different from the rest of
the document (e.g., the lead edge contains a black border).
Maps with grayscale or color content may copy best in this
mode.
To retain more light color information such as light gray or yellow
NOTE: If Photo or Color is selected as the Original, Type, the Off
setting is automatically selected. The contrast can still be adjusted by
pressing the key(s) beneath Image Quality, Copy.
(Light)
This setting works best for documents on translucent or
transparent media, such as vellum (tracing paper) or film, or with medium
levels of colored background on opaque media or for documents. Such
documents have a higher contrast between the foreground and
background than dark documents, but less contrast than normal
documents.
(Dark)
Use this setting for documents with a dark background
or with medium contrast between the foreground and background. In
this mode, the background is not suppressed, but the foreground image
is improved to increase the contrast.
Auto (factory default) - The Scanner automatically adjusts the image
quality parameters to obtain the best copy.
NOTE: All three Background Suppression settings can be adjusted
further by changing the contrast setting in the Image Quality and Copy
area.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 17
Background Suppression can operate in either the dynamic or static
mode based on the whether the DYNAMIC BACKGROUND REMOVAL
is enabled, check mark in the box or disabled, no check mark in the box.
Reference Menu CONFIGURATION>IMAGE ENHANCEMENT.
IMAGE ENHANCEMENT
COLOR IQ:
SRGB
NORMAL MODE:
BEST IQ
DYNAMIC BACKGROUND REMOVAL
When enabled, the dynamic mode will monitor the whole document and
adjust the image quality settings as the document is being scanned in
order to optimize the background of the copy.
When disabled, the static mode monitors the first two inches to establish
a background threshold that is used through out the document in order to
optimize the background of the copy.
Static Background Suppression is not available in the PRODUCTIVITY
mode.
The Copy option allows you to darken or lighten the contrast of the copy
with respect to the original document. Press the down arrow key to
darken the contrast. Press the up arrow key to lighten the contrast. The
indicator lamp for the selected contrast setting illuminates. The middle
contrast setting is the factory default setting.
Copy
You can use this feature to further adjust the effects of the Type and
Background Suppression selections. The feature operates with all four
Background Suppression modes.
NOTE: Copy is not selectgable in Color mode
18 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
The Reduce/Enlarge area of the Scanner Control Panel allows you to
select one of three reduction/enlargement modes - Auto, Manual, and
Preset. The illustration below depicts the Reduce/Enlarge portion of the
Control Panel.
Reduce/Enlarge
NOTE: Reduce/Enlarge can only be selected in Copy mode.
Auto
Auto automatically adjusts the reduction/enlargement to fit the size of
media selected. To select the Auto mode, press the key beneath
Reduce/Enlarge until the Auto indicator lamp illuminates.
NOTE: The size of the output media must be known in advance for this
feature to operate. Therefore, Auto is not a valid selection if both the
Synchro cut option and the Sheet and Auto media source options are
selected. If you select this combination, an INVALID AUTO
COMBINATION status is displayed.
Manual
Manual allows you to reduce the image captured by the Scanner to as
little as 25% or as much as 400% of the original size before the copy is
printed.
To select the Manual mode:
1. Press the key beneath Reduce/Enlarge until the Manual
indicator lamp illuminates. The MANUAL
REDUCTION/ENLARGEMENT screen is displayed.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 19
NOTE: If the indicator lamp is already lit, press the key once to display
the screen.
MANUAL REDUCTION/ENLARGEMENT
ENTER (25.0 – 400.0):
100.0%
2. Enter a reduction/enlargement between 25 and 400. You can
select any value between these limits in 0.1% increments.
3. Press the Enter key to confirm your choice and return to the
READY screen. The READY screen now displays the new
reduction/enlargement percentage.
NOTE: Pressing the Exit key rejects the choice and retains the previous
setting.
Preset
Preset (factory default) allows you to select a predefined reduction or
enlargement percentage.
To select the Preset mode:
1. Press the key under Reduce/Enlarge until the Preset indicator
lamp illuminates. The PRESET REDUCTION/ENLARGEMENT
screen is displayed.
NOTE: If the indicator lamp is already lit, press the key once to display
the screen.
PRESET REDUCTION/ENLARGEMENT
100.0%
SELECT:
2. Press the Previous or Next key until the desired
reduction/enlargement ratio is displayed. The possible choices
are any combination of the following:
·
·
·
·
50%, 100% (default), and 200%
65% and 129%, if the ANSI and ARCH sizes are enabled
71% and 141%, if the ISO A, ISO B or JIS B sizes are enabled
Up to six additional preset values, if these values have been
defined using the CUSTOM R/E Presets menu function.
20 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
NOTE: Refer to "Media Series" in the "Main Menu" section for more
information about enabling media series and defining custom presets.
3. Press the Enter key to confirm your choice and return to the
READY screen. The READY screen now displays the new
reduction/enlargement percentage.
NOTE: Pressing the Exit key rejects the choice and retains the previous
setting.
The middle portion of the Scanner Control Panel contains the graphical
display and the navigation keys. The illustration below depicts the
middle portion of the Control Panel.
Graphical Display
and Navigation Keys
READY TO COPY
INSERT DOCUMENT
AUTO
100.0
1
Next
Menu
Previous
Mode
Enter
Exit
The graphical display provides you with information and instructions
pertaining to the system. It consists of up to four lines of text and
graphics. The display can be adjusted upward for better viewing.
Graphical Display
Navigation Keys
The navigation keys, located beneath the display, are used to move
through the menu screens, to select items on the screen, and to specify
parameters when an options screen is displayed. Some keys have more
than one function depending on the screen being displayed at the time.
These special functions are explained in later sections.
Menu
The Menu key invokes the main menu. If a menu screen is already being
displayed, pressing this key exits the menus and directly returns you to
the previous READY State.
Previous
The Previous key highlights the previous item in a displayed list.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 21
Next
The Next key highlights the following item in a displayed list.
Enter
The Enter key either confirms the selection of the currently highlighted
item or confirms an entered numeric value.
Exit
The Exit key cancels a selection operation and returns you to a previous
screen. It has other effects, depending upon the specific situation, that
are explained later.
Mode
The Mode key is a valid selection only when READY is displayed on the
screen. This key is used to switch between the READY TO COPY mode
and the READY TO SCAN mode. The SCAN mode can be entered only
if the Scan to Net feature key is loaded.
Below are examples of the READY screen in COPY and SCAN modes.
NOTE: The COPY mode is disabled foe X2 TECH
READY TO COPY
INSERT DOCUMENT
AUTO
100.0%
1
READY TO SCAN
INSERT DOCUMENT
400 DPI
TIFF/CCITTG4
BIT
In the COPY mode, the scanned image, or set of images is printed on
the Printer and then deleted from the hard disk.
In the SCAN mode, the scanned image, or set of images, is stored on
the hard disk for later retrieval over a network by a client running on a
remotely located device. Refer to the "Scanning to the Network" section
for more information about the SCAN mode.
NOTE: The SCAN mode is an optional feature that is enabled by
installing the Scan to Net feature key Contact your XEROX
representative for ordering information.
22 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
The right side of the Scanner Control Panel contains a numeric keypad
for entering quantities, keys for selecting other features, and keys for
controlling the scanning and printing of images. To the left of some of
the keys are indicator lamps that illuminate when the associated feature
has been selected.
Numeric Keypad and
Special Features/Control
Keys
Transform
Sample
Batch
Sets Build
A B C
D E F
1
3
2
M N O
G H I
J K L
Finisher
6
4
5
W X Y
T U V
P R S
9
7
8
Store/
Recall
C/CA
/.
0
Start
Printer
Interrupt
Stop
The numeric keypad contains the 0 to 9 numeric keys, the decimal key
and the C/CA key.
Numeric Keypad
Numeric (0-9) keys
These keys are used for numeric entry, password entry, and copy
quantity fields.
NOTE: The letters next to the numbers are for entering in User and
Account IDs and Scan Directory information.
/. (Decimal key)
This key is used for entering alphanumeric values and string entries for
account and user idnetities and directory names.
NOTE: The forward slash (/) to the left of the decimal is for future use.
C/CA (Clear/Clear All) key
This key has the following functions:
·
·
When in READY TO COPY mode, one press clears the current
copy count to one. Two presses within one-second resets the
copy parameters to the default settings.
When in READY TO SCAN mode, pressing this key brings up
the CLEAR SCANNED IMAGE screen.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 23
·
·
·
·
When in READY TO BUILD SET mode, pressing this key brings
up the scanned document (Refer to Sets Build key section of
this manual for additional information).
When in the entry state for numeric entry fields, pressing this key
acts as a backspace/delete key. When the last digit is deleted,
the numeric field goes to zero.
When in password entry and string entry fields, pressing this key
acts as a backspace key. When the last character is deleted, the
field is blank.
When in quantity entry fields, pressing this key clears the field to
1.
The special features keys are used to activate, deactivate, or change
parameters associated with special features. An indicator lamp adjacent
to each feature key illuminates whenever the corresponding feature is
activated.
Special Features
Keys
The special features keys include the Printer Interrupt, Store/Recall,
Finisher, Sets Build, Batch, Transform, and Sample keys. These
keys are described in detail in the Special features keys section of this
guide.
The Start and Stop keys control the scanning and printing of images.
Scan Control Keys
Start key
The Start key is used to begin the copy sequence when the AUTOSCAN
feature is not enabled.
If you press the Start key while the status is NOT READY or INVALID
AUTO COMBINATION, the system will beep to indicate an invalid key
press. If you press the Start key while the status is READY TO COPY or
READY TO SCAN, the document is scanned.
NOTE: INVALID AUTO COMBINATION indicates an incompatible
combination of AUTO settings (i.e., Media Selection, Source set to
Sheet or Auto, Media Selection, Output Format set to Synchro, and
Reduce/Enlarge set to Auto).
Stop key
The Stop key allows you to immediately stop the scanning operation to
prevent damage to the document. Any scanned information is discarded.
The READY screen prompts you to remove the document. The Printer
and the Controller
24 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
The Printer and the Controller
For detailed operating instructions about the Printer and Controller
components of the WIDE FORMAT COPY SYSTEM and about network
connectivity, refer to the documentation listed below.
·
·
·
·
The XEROX WIDE FORMAT 8825/8830 Printer Operator
Manual
XEROX WIDE FORMAT 8850 and 510dp Series Printer
Operator Manual
XEROX WIDE FORMAT 721P Engineering Printer Operator
Manual
ColorgrafX X2 User Guide
The Controller Setup Guide/Network Administrato Guide (NAG) contains
the details for setting up the Controllers used with XEROX WIDE
FORMAT 8825/8830/8850/510dp Series and 721P printers. The Network
Administrator's Guide contains valuable information about network
connectivity and help in determining network connectivity settings.
The Web Printer Manager Tool User Guide contains the details for
configuring the settings for the Controller used with the XEROX WIDE
FORMAT X2 TECH color printer.
Powering On the WIDE FORMAT
COPY SYSTEM
To power on the XEROX WIDE FORMAT COPY SYSTEMS, you first
must switch on the Scan System and wait for 30 seconds or check that a
P is displayed on the status LED in the back of the Scan System. Then
switch on the Printer, then the Controller.
Follow the instructions provided in this section for your system.
When the WIDE FORMAT SCAN SYSTEM is present, the DDS
parameter must be set to Enabled in order to enable the COPY/SCAN
functionality. If the DDS parameter is set to Disabled, COPY/SCAN
functionality will not be enabled.
Initial power-on
The default for this parameter is disabled. You must ensure that it is set
to Enabled when powering on the XEROX WIDE FORMAT SCAN
SYSTEM for the first time. After setting the DDS parameter, wait 30
seconds, and then power the system off then on. Once you enable this
parameter, it will remain enabled (even following future software
upgrades).
For the XEROX WIDE FORMAT COPY SYSTEM 510 Series or 8825,
8830, and 8850, you can set this parameter from either the
CONTROLLER CONFIGURATION screen of the Printer Control Panel or
the PRINTER SETUP/Miscellaneous page of the Web PMT. For the
XEROX WIDE FORMAT COPY SYSTEM 721P, you can only set this
parameter from the Web PMT. Refer to the 8825/8830/8850/510
Series/721P Controller Setup Manual or the Web PMT Printer Manager
Tool User Guide for more information.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 25
To switch on the Scanner, press the Power On/Off Switch on the back of
the Scanner to the On (I) position as shown below. Wait for 30 seconds
or until a P is displayed on the status LED.
Switching on the
Scan System
When the Scanner is switched on, the fluorescent lamp inside the
Scanner illuminates immediately. If the lamp does not illuminate, refer to
the "Problem solving" section of this guide.
Certain Controllers receive their power from the Printer. They do not
have a separate power switch.
Switching on the
Controller and the Printer
(XEROX WIDE FORMAT
COPY SYSTEM
NOTE: Ensure that the Scanner is switched on first and the P is
displayed in the Status Indicator window.
8825/8830/8850)
To power on these Controllers and the Printer, do the following:
1. Switch the Printer Power Switch to the Off (O) position.
2. Switch the Circuit Breaker Switch to the On (I) position.
3. Switch the Printer Power Switch to the On (I) position.
26 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
A: Controller
B: Circuit Breaker switch
C: Printer Power Switch
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 27
Switching on the HFT
Controller and the
Printer (XEROX WIDE
FORMAT
8825/8830/8850/510
Series/721P)
NOTE: Ensure that the Scanner is switched on first and the P is
displayed in the Status Indicator window.
The HFT Controller has its own power switch. When powering it on, first
power on the Controller and then power on the Printer.
Controller
Power
Switch
510 Series
Power
Switch
721P Power
Switch
28 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Switching on the
Printer and the
Controller (X2 TECH)
NOTE: Ensure that the Scanner is switched on first and the P is
displayed in the Status Indicator window before powering on the
Controller.
The KLF Controller and the X2 TECH printer each have their own power
switch. When powering them on, first power on the printer, then the
scanner, wait for the P to be displayed, then power on the Controller.
The Scanner requires about 45 seconds to warm up and initialize after
you power on the WIDE FORMAT COPY SYSTEM. Once the
initialization is complete, the READY screen is displayed. Below is an
example of the READY screen.
Scanner Warm-up
READY TO COPY
INSERT DOCUMENT
AUTO
100.0 %
1
You can now insert a document into the Document Feed Tray of the
Scanner. The Scanner will then transport the document to the starting
position. This transportation of the document is called staging.
If you cannot insert a document into the feed mechanism and achieve
staging after approximately 4 minutes, refer to the "Problem solving"
section of this guide.
XEROX WIDE FORMAT COPY SYSTEM
Getting to know the WIDE FORMAT COPY SYSTEM · 29
Powering off the System
To power off the WIDE FORMAT COPY SYSTEM, do the following:
1. Power off the Controller and the Printer.
·
·
For the 8825/8830/8850/510 Series, switch the Circuit Breaker
Switch to the Off (O) position. Then switch the Printer Switch to
the Off (O) position.
For the 721P, first power off the Printer. Then power off the
Controller.
2. Switch off the Scanner by pressing the Power On/Off Switch on
the back of the Scanner to the Off (O) position as shown below.
30 ·Getting to know the WIDE FORMAT COPY SYSTEM
XEROX WIDE FORMAT COPY SYSTEM
Document quality
Document quality
Document quality is the primary factor in obtaining good copies from
scanned originals. For most documents, the four Background
Suppression key selections with DYNAMIC BACKGROUND REMOVAL
enabled, which is the default setting, provides an accurate copy. Some
documents, however, require manual adjustments to the settings to
This section explains the DYNAMIC BACKGROUND REMOVAL feature,
describes the characteristics of good quality and bad quality documents,
provides tips for preparing and organizing documents for scanning, and
summarizes the procedures for scanning documents of different quality
types.
Dynamic Background Removal
NOTE: DYNAMIC BACKGROUND Removal cannot be diasable
(unchecked) when using the Productivity mode.
The DYNAMIC BACKGROUND REMOVAL eliminates the need to make
additional manual adjustments for most input documents. Reference
Menu, CONFIGURATION > IMAGE ENHANCEMENT.
This feature allows the system to dynamically adjust itself for each
document. There are two modes associated with this feature:
·
·
When DYNAMIC BACKGROUND REMOVAL is enabled, the
image is continually monitored as it is being scanned and the
copy quality parameters adjusted to achieve the best copy
quality.
When DYNAMIC BACKGROUND REMOVAL is not enabled, the
process takes a 0.70 inch (17.8 mm) snapshot over the full width
of the image after the first 1.5 inches scanned. It uses this fixed
area to set the copy parameters for the remainder of the image
being scanned. This operating mode should be used for
documents with consistent background throughout.
DYNAMIC BACKGROUND REMOVAL only monitors the document in
the process direction, from the lead edge to the trail edge. It cannot
make adjustment from the left side to the right side of the document. For
example, if the input document is dark, DYNAMIC BACKGROUND
XEROX WIDE FORMAT COPY SYSTEM
Document quality · 31
REMOVAL will automatically make the appropriate compensation to
optimize the reproduction of the dark details. If the input document has a
faded background, the feature will enable a faithful reproduction of the
original. However, the faded background must be inserted with the fading
running in the process direction with the darker side being inserted first.
In some cases, you may wish to optimize the settings for individual
documents. For example, you may not wish to faithfully reproduce
paste-up lines, or other artifacts on the original. For this reason,
additional controls are available for selection of document type,
document image quality, desired output darkness, and background
suppression.
The DYNAMIC BACKGROUND REMOVAL feature, when enabled, uses
information about the document captured during the scanning process to
set image quality settings. The system automatically adjusts for the
darkness of the background and the image content through out the
length of the document. When not enabled, it only uses the information in
a 0.70 (17.8 mm) area over the width of the document to establish the
image quality settings. Therefore, best results can be obtained if the
document is fed in with an edge that has a representative sampling of
both the background and the foreground image.
The Dynamic Background Removal feature provides an accurate copy
for most documents including blueline, blueprints, color line art/text, and
mixed documents containing combinations of halftone and art, or
photograph and art. For documents with inverted images, the INVERT
function should be enabled. Refer to "Inverting an image" in the "Special
features keys" section for instructions on the INVERT function.
The AUTOWIDTH /AUTOCENTER features enable the system to
automatically detect the width and center of the document. In cases
such as transparencies or translucent documents where automatic
detection is not possible, a message will prompt you to enter the width
manually. You then must center the document before inserting it into the
Scanner.
Automatic edge
detection and
document centering
You can enable/disable the AUTOWIDTH/CENTER feature at any time.
Refer to "Scanner Control" in the "Main Menu" section of this manual for
more information.
PRODUCTIVITY MODE: This feature is made available with version 10.0
AccXES software, and requires a new WIDE FORMAT SCAN SYSTEM
with the Productivity Document Feed Tray with the discrete width
sensors. This feature measures the document width without doing a pre-
scan, requiring the operator to manually align the document within the
media size guidelines on the Feed-in Tray. The width sensors eliminate
the need for a prescan thereby increasing the overall throughput of the
system resulting in higher productivity
When the PRODUCTIVITY MODE is used the operator must select the
media series, ANSI, ARCH, ISO A, CUSTOM, etc since the number of
sensors that can be provided can not monitor every media series. The
PRODUCTIVITY mode can be enabled/disabled at anytime. Refer to
"Scanner Control" in the "Main Menu" section of this manual for more
information.
32 ·Document quality
XEROX WIDE FORMAT COPY SYSTEM
Determining document quality
Some documents require additional adjustments to obtain the best copy
quality. Documents of good quality are easy to scan and usually give
good copies on the first attempt. Documents of bad quality may require
more than one attempt, using different settings, to obtain the best copy
quality.
What is a good
quality document?
Backgroun
Foregroun
4"
4"
A good quality document has all of these characteristics:
·
The contrast between the foreground (the image of interest) and
the background is high. The foreground may be color or black.
·
The foreground is a solid, high-density black or dark color (or
dark blue on a blueline, or dark brown on a sepia). The
foreground density is uniform. There is only one kind of
foreground (e.g., there are no pencil additions on a blueline). If
the document is of mixed type, the foreground is color.
·
If the document is white on black or white on blue, the
foreground is clear white or nearly white, and the background is
a solid, high-density black or dark color.
·
·
The background is white or light-colored and is free of speckling
or other noise. The background density is uniform.
The document has no creases, folds, stains, tears or extraneous
marks that the Scanner might interpret as foreground.
Bad quality documents often require special attention to achieve a
usable image. Fortunately, image processing technology is incorporated
that can extract acceptable images from documents degraded by many
kinds of problems.
What is a bad quality
document?
A bad quality document has one or more of the following problems:
·
·
·
The foreground is light (e.g., a faded or overexposed blueprint or
light pencil lines).
The foreground has variable density (i.e., some parts are dark
and some parts are light).
The foreground consists of two or more densities or colors (e.g.,
pencil additions on an ink drawing, or pencil or ink additions on a
sepia).
·
The background is medium dark or dark (e.g., underexposed
blueprint).
·
·
The background has variable density.
The background has speckles.
XEROX WIDE FORMAT COPY SYSTEM
Document quality · 33
·
The document has creases, folds, stains, tears, or extraneous
marks that the Scanner might interpret as foreground.
Preparing documents
When preparing documents for scanning, keep the following points in
mind:
If documents have been stored rolled up, flatten them out. They will be
much easier to handle if they have been stored flat for at least eight
hours. The longer that documents have been stored flat, the easier it will
be to scan them. Rolled-up documents will typically roll back up after
being scanned.
If possible, sort the documents you are going to scan according to these
guidelines:
·
First, group the documents by media type -bond, vellum or
film. Within each document type, you can further group the
documents by image type (e.g., blueprint, pencil, sepia, line,
photo, mixed (photo and line, blueline and pencil), and so
forth).
·
Line documents contain lines or text against a highly
contrasted background.
·
·
Photo documents are continuous-tone or grayscale images.
Mixed documents contain both line elements and photo
elements or halftone images.
·
Scanning groups of documents of the same type or series
(ANSI, ARCH, etc.) minimizes the number of changes you
will need to make to the Image Quality settings.
·
Next, divide the documents in each media type group into "good"
and "bad" piles based on your evaluation of their foreground and
background quality. See "What is a good quality document?"
and "What is a bad quality document?" in this section for
assistance in doing so.
·
·
By grouping the documents in this way, you can scan the good
quality documents first. Then you can focus on the bad quality
documents, which will require more attention.
Next, determine if any of the documents are inverted (i.e., white
or light foreground against dark background). If any documents
are inverted, refer to "Inverting an image" in the "Special features
keys" section.
·
Finally, sort the documents by size or series (ANSI, ARCH, etc.).
This minimizes the number of times you will need to change the
Media Selection, Output Format settings when using preset or
custom format sizes.
34 ·Document quality
XEROX WIDE FORMAT COPY SYSTEM
Scanning strategies
When scanning documents, always try the default Image Quality
settings first. Select the documents type -, line, photo, mixed or color
and use the Original, Type, Normal, Line, Photo or Color default
settings for that type. Color is a Scan to Net feature and only available in
SCAN mode. These settings have been designed to give the optimum
image quality for most documents.
If you have a special original type, you may want to try some of the
advanced image processing features available on the Scanner. Table 2
describes the scanning strategies for special original types.
Table 2. Scanning strategies for special documents
Type of original
First step to try
Second step to try
Third step to try
Color photograph
Set Original Type to Photo
Mode Scan: Set Original
Type to Color and
Set Original Type to
Normal and
Background
Suppression to Off.
Color lithograph
Color map
Mode COPY: Set Original
Type to Normal..
Set Original Type to
Normal and Background
Suppression to Off
Set Original Type to
Photo
Mode SCAN: Set Original
Type to Color.
Mode COPY: Set Original
Type to Normal..
Set Original Type to
Normal and Background
Suppression to Off.
Set Original Type to
Photo
Mode SCAN: Set Original
Type to Color.
Old blueprint or sepia Set Original Type to Line
with dark background and Background
Suppression to Auto.
Set Original Type to Line, Adjust the Copy
Background Suppression
to dark original,
contrast as required
for best image
quality.
Transform, Invert to ON
Transform, Invert to ON.
Old blueprint or sepia Set Original Type to Line
If fade is still visible in the Adjust the Copy
with dark background and Background
copy, rotate the original
90 degrees. Generally,
feeding the darkest edge
first provides the best
results.
contrast as required
for best image
quality.
and side-to-side
fading
Suppression to Auto.
Faded line/text
drawing
Set Original Type to Line,
Background Suppression to copy, rotate the original
Auto. 90 degrees.
If fade is still visible in the Adjust the Copy
contrast as required
for best image
quality.
In reduction, use
Reduction Line
Preservation..
XEROX WIDE FORMAT COPY SYSTEM
Document quality · 35
Type of original
First step to try
Second step to try
Third step to try
Line, photo or mixed
original on film, clear
film, vellum/tracing or
other translucent
media
Set Background
Suppression to (light) and
Normal. Select Photo for
photo and select Line for
line drawing. Use Normal
for mixed documents.
Film original with
banding in
background area
Set Background
Suppression to (light).
Select Line for line drawing
Film original with
blurring text or gray
shadows
Set Background
Suppression to (light) and
Type to Line
36 ·Document quality
XEROX WIDE FORMAT COPY SYSTEM
Image Quality
The Image Quality area of the Scanner Control Panel allows you to
make adjustments for both the type of Original document and the output
Copy to produce the best possible copy quality. It contains selections for
Original (Document): Type and Background Suppression, and Copy
options lighter or darker. There is also an IMAGE ENHANCEMENT
selection in the Menu options that can be used in some copy jobs to
improve the image quality. Press the Menu key and scroll to
CONFIGURATION > IMAGE ENHANCEMENT.
The illustration below depicts the Image Quality portion of the Control
Panel.
XEROX WIDE FORMAT COPY SYSTEM
Image Quality · 37
Original, Type
Type
The Type option allows you to specify the type classification of your
document. To select the document type, press the key beneath the
Type settings until the desired Type indicator lamp illuminates.
NOTE: The SCAN OPTIONS will not be displayed unless the Scan to
Net feature is installed. To order this feature, contact your XEROX
representative.
COPY MODE
The Type settings are: Normal, Line, and Photo. Color is only available
in SCAN mode.
Type, Normal, Line,
Photo,
The Line mode scans with high contrast to provide exceptional copying
of line drawings even light pencil is reproduced as a dark black line.
Select Photo when the document contains a gray scale or color image,
such as a photograph.
Normal mode attempts to reproduce the document being scanned to
provide the best image quality including halftones and shadings as well
as fine lines.
1. Select the Line, Photo or Normal by pressing the arrow key
below Original, Type.
READY TO COPY
INSERT DOCUMENT
AUTO
100.0%
1
Additional image quality settings associated with Normal, Line, and
Photo mode can be obtained by using the Menu key. Access the
IMAGING menu to use the REDUCTION LINE PRESERVATION and the
IMAGE ENHANCEMENT menu to use NORMAL MODE and DYNAMIC
BACKGROUND REMOVAL.
1. Press the Menu key to enter the menu options.
2. Press the Previous and Next keys to scroll to the
CONFIGURATION menu and press the Enter key.
3. Use the Previousand Next keys to scroll to the IMAGE
ENHANCEMENT or COPY OPTIONS>IMAGING menu, then press
the Enter key.
4. Use Previousand Next keys to select the option the press the Enter
key to select and enable the settings.
38 ·Image Quality
XEROX WIDE FORMAT COPY SYSTEM
IMAGING screen
IMAGING
AUTO-ROTATE
4 REDUCTION LINE PRESERVATION
REDUCTION LINE PRESERVATION — fine lines in the original
document are preserved when reducing images during copying
in Normal and Line mode sonly.
IMAGE ENHANCEMENT screen.
IMAGE ENHANCEMENT
SRGB
COLOR IQ:
NORMAL MODE:
BEST IQ
ü DYNAMIC BACKGROUND REMOVAL
NORMAL MODE — BEST IQ provides the best image quality,
but it is a slower scanning speed.
FASTEST provides a faster scanning speed with lower image
quality. Only available if the Turbo III feature key is installed.
DYNAMIC BACKGROUND REMOVAL —The Dynamic
Background Removal feature, when enabled, uses information
about the document captured during the scanning process to set
image quality settings. The system automatically adjusts for the
darkness of the background and the image content through out
the length of the document. Reference DYNAMIC
BACKGROUND REMOVAL in the Document Quality section of
this manual for additional information.
XEROX WIDE FORMAT COPY SYSTEM
Image Quality · 39
SCAN MODE
Normal mode attempts to reproduce the document being scanned to
provide the best image quality including halftones and shadings as well
as fine lines. To select the scan options for Color Mode:
Type, Normal
1. Press the Mode key. The Please Enter Directory screen is
displayed.
2. Enter the Directory Name. The READY TO SCAN INSERT
DOCUMENT screen is displayed.
3. Select the Normal by pressing the arrow key below Original,
Type key until the Normal light comes on. The SCAN OPTIONS
(NORMAL) screen is displayed.
4. Use the Enter key to enable/disable checkbox selection and the
Next or Previous Key to select options with a colon (eg.
FORMAT: TIFF).
The options available for selections displayed on the screen will change
depending on the FORMAT and COMPRESSION that are selected.
Listed below are the selections and available options and their definition:
·
PREVIEW - Use this checkbox to enable or disable the
generation of a preview image for your scanned document.
Default is enabled (checkbox is checked)
·
FORMAT - Use this selection to determine which format you
would like to have the scanned image saved in, TIFF, CALS (1
BIT only) or PDF. Default is TIFF.
The screen shown below only appears in the SCAN mode.
Additional image quality selections are available by pressing the
Menu key and scrolling to CONFIGURATION>COPY
OPTIONS>IIMAGING or CONFIGURATION> IMAGE
ENHANCEMENT. Refer to the Main Menu section of the manual
for additional information on these selections.
SCAN OPTIONS (NORMAL)
ü
PREVIEW
FILE FORMAT:
TIFF
40 ·Image Quality
XEROX WIDE FORMAT COPY SYSTEM
Line — Select Line for an image containing text, line art, or a mixture of
these. If the COPY mode is selected the READY TO COPY screen will
be displayed. If the Mode selected is SCAN, and the Scan to Net
Feature Key is installed, the SCAN OPTION (LINE) screen will be
displayed.
Type Line
SCAN OPTIONS (LINE)
ü PREVIEW
TIFF
FILE FORMAT:
2. elect the Line by pressing the arrow key below Original, Type
key the SCAN OPTIONS (LINE) is displayed.
3. Press the Previous or Next key to highlight the scan option you
wish to change.
4. Select one of the following:
·
PREVIEW — Default is enabled and a check mark is present in
the box. Press the Enter key to enable/disable the preview.
When PREVIEW is enabled, a small JPEG (.JPG) file is created
during the scanning process and stored on the hard disk
AccXES Client Tools software, running on a network connected
terminal, can use this file to display a preview of the scanned
image.
·
FILE FORMAT — Default is TIFF. Use the Next and Previous
keys to select the format for the document to be saved as. The
selection is TIFF, CALS, PDF or JPEG.
5. Press the Enter key to confirm the select.
XEROX WIDE FORMAT COPY SYSTEM
Image Quality · 41
Select Photo when the document contains a gray scale or color image,
such as a photograph. When Photo is selected in the Scan Mode, the
screen below will be displayed. The screen provides additional options
for the user
Type Photo
SCAN OPTIONS (PHOTO)
PREVIEW
COMPRESSION:
RAW
FILE FORMAT: TIFF
The SCAN OPTIONS (PHOTO) menu allows you to perform the
following functions:
·
Enable or disable PREVIEW in Photo mode. When PREVIEW
is enabled, a small JPEG (.JPG) file is created during the
scanning process and stored on the hard disk AccXES Client
Tools software, running on a network connected terminal, can
use this file to display a preview of the scanned image.
·
·
Specify the saved document compression format for Photo
mode.
View the saved document file format for Photo mode. The
format is 8 bit TIFF.
NOTE: This option will not be displayed unless the Scan to Net feature
is enabled. To order this feature, contact your XEROX representative.
NOTE: The Background Suppression option cannot be used with the
Photo setting. If Photo is selected, Background Suppression is
automatically set to Off.
1. Enter the SCAN mode by pressing the Mode key then entering
the Directory Name and pressing the Enter key.
2. Select Photo by pressing the arrow key below Original, Type
key. The screen shown below is displayed.
SCAN OPTIONS (PHOTO)
PREVIEW
COMPRESSION:
RAW
FILE FORMAT: TIFF
3. Press the Previous or Next key to highlight the scan option you
wish to change.
42 ·Image Quality
XEROX WIDE FORMAT COPY SYSTEM
4. Do one of the following:
·
For PREVIEW, press the Enter key to enable or disable the
option. A check mark appears in the box to the left of the option
when the option is enabled. The factory default setting is
enabled.
·
For COMPRESSION, press the Previousor Next key to
highlight the desired setting. Then press the Enter key to select
the highlighted format. The choices are RAW and PACKBITS.
The factory default setting is RAW
5. For FILE FORMAT, the selection is TIFF, Repeat steps 3 and 4
to change the remaining setting, if desired.
6. Press the Enter key to confirm the selection.
7. Press the Exit key to return to the Ready screen.
Color — Select Color when scanning full color documents. When Color
Type is select a version of the following screens will be displayed. The
content of the screen will depend on the selected FORMAT and
COMPRESSION.
Type, Color
These screen will only be displayed in SCAN mode when the Scan to
Net and Color Scanner feature keys are installed. The Normal and
Photo LEDs will be lit when Color is selected.
To select the scan options for Color Mode:
1. Press the Mode key. The Please Enter Directory screen is
displayed.
2. Enter the Directory Name. The READY TO SCAN INSERT
DOCUMENT screen is displayed.
3. Select the Color by pressing the arrow key below Original, Type
key until the Normal and Photo lights come on. The SCAN
OPTIONS (COLOR) screen is displayed.
4. Use the Enter key to enable/disable checkbox selection and the
Next or Previous Key to select options with a colon (e.g.
FORMAT: TIFF).
The options available for selections displayed on the screen will change
depending on the FORMAT and COMPRESSION that are selected.
Listed below are the selections and available options and their definition:
·
·
·
PREVIEW - Use this checkbox to enable or disable the
generation of a preview image for your scanned document.
Default is enabled (checkbox is checked)
FORMAT - Use this selection to determine which format you
would like to have the scanned image saved in, TIFF or JPEG.
Default is TIFF.
COMPRESSION (TIFF selected) - Use this selection to
determine the compression method to apply to the saved TIFF
document. Select one of the following:
·
PACKBITS - Saves the document as 24-bit RGB
compressed.
XEROX WIDE FORMAT COPY SYSTEM
Image Quality · 43
·
·
INDEX - Saves the document as 8-bit indexed RGB (using
thresholding) compressed with PACKBITS.
INDEX ED - Saves the document as 8-bit indexed RGB
(using error diffusion) compression with PACKBITS
SCAN OPTIONS (COLOR)
: TIFF
PREVIEW
FORMAT:
: PACKBITS
ü
COMPRESSION:
SCAN OPTIONS (COLOR)
PREVIEW
: TIFF
FORMAT:
ü
INDEX
COMPRESSION:
PALETTE:
DEFAULT
·
PALETTE - Is shown only when the selected FORMAT is TIFF
and the COMPRESSION is INDEX or INDEXED. Use this
selection to determine which palette to use during RGB-to-index
color conversion. Select one of the following:
·
·
DEFAULT - Is the standard Windows system palette.
CAD_GIS - Is an AutoCAD-based palette suitable for
scanning CAD documents and GIS maps.
·
·
WEB - Is a Windows WEB palette of 216 colors suitable for
publishing documents on the WEB.
PERCEPTUAL - Perceptual palette or Visual palette gives
more weight to visually sensitive colors.
SCAN OPTIONS (COLOR)
JPEG
PREVIEW
FORMAT:
NORMAL
ü
COMPRESSION:
·
COMPRESSION (JPEG selected) - Use this selection to
determine the compression method to apply to the saved JPEG
document. Select one of the following:
·
BEST IQ - Saves a document at a lower compression ratio
but has higher image quality.
44 ·Image Quality
XEROX WIDE FORMAT COPY SYSTEM
·
·
NORMAL - Saves a document at an average compression
ratio and has average image quality.
BEST COMPRESSION - Saves a document at a higher
compression ratio but has a lower image quality
Background Suppression
The Background Suppression enables you to make adjustments for
documents that contain poor contrast between the foreground image and
the background. Background Suppression monitors the pre-scans
image, to ensure the best image quality possible. In the PRODUCTIVITY
mode, there is no prescan, therefore Background Suppression is done
while the document is being scanned.
NOTE: Off is the only choice for Photo, Scans, and Color Scanning.
Four choices are provided:
Off
This setting disables Background Suppression. It produces a
document that reproduces all the characteristics of the original document
with minimum alteration. Choose this selection when:
·
·
·
The lead edge of the document is very different from the rest of
the document (e.g., the lead edge contains a black border).
Maps with grayscale or color content may copy best in this
mode.
To retain more light color information such as light gray or yellow
(Light)
This setting works best for documents on translucent or
transparent media, such as vellum (tracing paper) or film, or with medium
levels of colored background on opaque media or for documents. Such
documents have a higher contrast between the foreground and
background than dark documents, but less contrast than normal
documents.
(Dark)
Use this setting for documents with a dark background
or with medium contrast between the foreground and background. In
this mode, the background is not suppressed, but the foreground image
is improved to increase the contrast.
Auto (factory default) - The Scanner automatically adjusts the image
quality parameters to obtain the best copy
NOTE: All three Background Suppression settings can be adjusted
further by changing the contrast setting in the Image Quality, Copy
area.
Copy
The Copy option allows you to darken or lighten the contrast of the copy
with respect to the original document. Press the down arrow key to
darken the contrast. Press the up arrow key to lighten the contrast. The
XEROX WIDE FORMAT COPY SYSTEM
Image Quality · 45
indicator lamp for the selected contrast setting illuminates. The middle
contrast setting is the factory default setting.
You can use this feature to further adjust the effects of the Type and
Background Suppression selections. The feature operates with all four
Background Suppression modes.
46 ·Image Quality
XEROX WIDE FORMAT COPY SYSTEM
Making copies
Making copies
When the Graphical Display indicates READY TO COPY, the WIDE
FORMAT COPY SYSTEM is ready to make copies.
NOTE: The X2 TECH printer does not currently support the Copying
mode.
Several settings are available for controlling how the Scanner starts and
finishes a scan. These settings are accessible from the SCANNER
CONTROL option of the CONFIGURATION menu.
Controlling the scan
SCANNER CONTROL
AUTOSCAN
4
FRONT
DOCUMENT RETURN:
MODE:
PRODUCTIVITY — ARCH
When making a copy, you need to be aware of these settings. If any of
these settings have been changed from the default settings, the Scanner
may not operate according to your expectations.
Below is a brief summary of the scan control settings. For complete
information about these settings, refer to "Scanner Control" in the "Main
Menu" section of this manual.
AUTOSCAN
AUTOSCAN enabled is the default setting. Normally, the AUTOSCAN
mode is enabled. When it is enabled, the Scanner automatically begins
the scanning of a document when the document is inserted. If
AUTOSCAN is disabled, the Scanner transports the document to the
starting position and then waits for you to press the Start key before
beginning the scan.
DOCUMENT RETURN
FRONT is the default setting. When the DOCUMENT RETURN feature
is set to FRONT, the Scanner returns the document to the front or
XEROX WIDE FORMAT COPY SYSTEM
Making copies · 47
READY position at the completion of the scan. When the DOCUMENT
RETURN feature is set to REAR, the Scanner delivers the document to
the rear Stacker at the completion of the scan.
Some documents will always exit to the rear at the completion of the
scan regardless of the DOCUMENT RETURN setting. These documents
include:
·
·
·
Thick documents
Documents longer than 5 feet (1.52 meters)
Documents over 36 inches (914 mm) in width
MODE:
MANUAL
The user must enter the width of the document manually, and very
carefully center the document when inserting it into the Scanner. The
document is prescanned in this mode.
AUTOWIDTH
AUTOWIDTH enabled is the default setting. When AUTOWIDTH is
selected, the Scanner automatically detects the width of the
document.AUTOWIDTH/AUTOCENTER. The document is prescanned in
this mode.
When AUTOWIDTH/AUTOCENTER is enabled, the Scanner
automatically centers the image and automatically detects the document
width.
PRODUCTIVITY - ANSI
PRODUCTIVITY is only available on Scanners with AccXES firmware
10.0 or higher, Scanner firware 3.2.5and the Productivity Document
Feed Tray that includes discrete width sensors. PRODUCTIVITY - ANSI
is the default. Other media type selections include ARCH, ISO A, ISO B,
JIS B and CUSTOM. These selections must be made so that the sensors
detect the correct width. This feature eliminates the prescan width
measurement, which increases document throughput speed resulting in
greater productivity. CUSTOM requires standard media sizes to be
entered in CUSTOM MEDIA FORMATS.
AUTOWIDTH and AUTOWITH/AUTOCENTER are not available in this
mode.
Reference Menu, CONFIGURATION>SCANNER CONTROL, MODE: for
additional information.
48 ·Making copies
XEROX WIDE FORMAT COPY SYSTEM
The Image Quality area of the Scanner Control Panel allows you to
make adjustments for both the type of original document and the output
copy to produce the best possible image quality. It contains selections
for Original (Document): Type and Background Suppression, and
Copy options lighter or darker.
Image Quality
The illustration below depicts the Image Quality portion of the Control
Panel. Refer to the Image Quality section of this manual for additional
information.
There are many settings. other than Media Selection, Image Quality
and Reduce/Enlarge areas, available on the Control Panel. The
Transform special features key allows you adjust the margins around the
image, specify the position of the image on the media, and transform the
image into a mirror and/or inverted. Refer to the applicable sections of
this guide for detailed information about the many document settings
available to you.
XEROX WIDE FORMAT COPY SYSTEM
Making copies · 49
Making a copy with the default
settings
When the default document settings are used, the display indicates that
the roll of media that best fits the size of the original document will be
automatically selected. The reduction/ enlargement setting is 100%, so
the copy will be the same size as the original document. The copy
quantity is set to 1.
The illustration below shows the READY screen in its default state.
READY TO COPY
INSERT DOCUMENT
AUTO
100.0%
1
NOTE: Many document settings other than the default settings are
possible. For example, the options keys on the Scanner Control Panel
allow you to control the media selection, image quality and
reduction/enlargement percentage. The Transform special features key
allows you adjust the margins around the image, specify the position of
the image on the media, and transform the image into a mirror and/or
inverted image. Refer to the applicable sections of this guide for detailed
information about the many document settings available to you.
NOTE: When scanning to print, the copy is made using the current
Printer processing defaults including margins. If the image being
scanned is the same size as the media being used, set the margins to 0
(zero) to prevent the image from bieng clipped or select a larger media
size.
To make a copy using the default document settings:
1. Insert the original document face down and centered on the
Document Feed-in Tray of the Scanner.
NOTE: If the document is not exactly centered and the AUTOCENTER
feature is enabled, the Scanner will automatically correct the problem
electronically. The resulting image will still be correctly positioned on the
output media. If AUTOWIDTH/AUTOCENTER is disabled, you will need
to carefully center the document when inserting it. Refer to "Controlling
the scan" on the previous page. AUTOWIDTH/AUTOCENTER is not
available in the PRODUCTIVITY mode, requiring the user to manually
align the document within the appropriate document size guidelines on
the Feed-in Tray.
2. Gently move the document forward until the lead edge engages
the feed rolls. The Scanner transports the document to the
50 ·Making copies
XEROX WIDE FORMAT COPY SYSTEM
starting position. It then scans the document. The resulting
image is electronically sent to the Printer and your copy is
printed.
NOTE: If AUTOSCAN is disabled, you will need to press the Start key to
begin the scan. Refer to "Controlling the scan" on the previous page.
NOTE: If the PRODUCTIVITY mode is enabled the document will start
scanning immediately. If the PRODUCTIVITY mode is not enabled, the
document will pre-scan a small distance then reverse itself before
starting the complete scan.
3. When the document is returned to the READY position, do one
of the following:
·
Pull the document to remove it. Lift the Thick Document Lever to
remove fragile or thick documents.
·
Press the Start key on the Scanner Control Panel to scan the
document again.
NOTE: If DOCUMENT RETURN is set to REAR, the document is
delivered to the rear Stacker. Some documents exit to the rear Stacker
regardless of the DOCUMENT RETURN setting. Refer to "Controlling
the scan" on the previous page.
Making a copy the same size as the
original document
1. Set the Media Selection Source to Auto. The Auto indicator
lamp illuminates. This setting allows the WIDE FORMAT COPY
SYSTEM to automatically select the available media roll that
best fits the image width.
NOTE: If the correct media size is not loaded, the next larger size will be
used.
2. Select the Media Selection, Type. The default setting is Bond.
3. Set the Media Selection, Output Format to Synchro. This
setting cuts the media to the same length as the original
document.
4. Set Reduce/Enlarge to Preset. If the size is not already set to
100%, use the Previousand Next keys to select a reduction and
press the Enter key.
5. Insert the document face down into the Scanner. If the scan
does not start automatically, press the Start key.
NOTE: To set the scan to begin automatically, refer to "Scanner Control"
in the "Main Menu" section.
NOTE: If the image needs to be rotated to fit on the selected media size,
additional processing time is required. If possible, feed the original
XEROX WIDE FORMAT COPY SYSTEM
Making copies · 51
image so that no image rotation is required. This will achieve the fastest
processing time. For example, if an A-size copy is required on a 12-inch
(30.48 cm) roll, feed the original with the short edge first, not the long
edge first. If a B-size copy is required on a 17-inch roll, feed the
document with the long edge first, not the short edge first.
The Scanner scans the document and the Printer (if not already busy)
prints the copy immediately. If the Printer is busy when the scan is
made, the copy will be printed when the Printer becomes available.
When the Scanner detects the trail edge of the document, the Printer
automatically cuts the media so that the copy is the same length as the
original document.
Fitting the image to a fixed copy size
The scanned image can be automatically fit onto a predefined size of
media.
1. Set the Media Selection, Source to Auto. The Auto indicator
lamp illuminates. This setting automatically selects the available
media roll that best fits the image width.
2. Select the Media Selection, Type of media. The default setting
is Bond.
3. Set the Media Selection, Output Format to Preset and select
the desired page size. This setting cuts the media to a
previously defined length that the operator chooses.
PRESET OUTPUT FORMAT
SELECT
8.5 X 11 ANSI A
4. Press the Previous or Next key until the desired output size is
highlighted.
5. Press the Enter key to confirm your choice.
6. Set the Reduce/Enlarge to Auto.
7. Insert the document face down into the Scanner. If the scan
does not start automatically, press the Start key.
NOTE: To set the scan to begin automatically, refer to "Scanner Control"
in the "Main Menu" section of this manual.
The Scanner scans the document, and the Printer (if not already busy)
prints the copy immediately. If the Printer is busy when the scan is
made, the copy will be printed when the Printer becomes available.
52 ·Making copies
XEROX WIDE FORMAT COPY SYSTEM
Scanning when using a Folder
Scanning when using a Folder
When using a Folder, the document must be inserted in the correct
orientaqtion in order to have the title block visible after the copy is folded.
Refer to the Finisher key information in the Special feature keys section
of this manual for additional information to set up the desired fold and
other Finisher options. Documents larger than 80 inches (2.1M) can only
be partially folded.
When using the Reduce/Enlarge feature and a Folder, you must orient
and insert the document title block in the same orientation as the
resulting enlargement or reduction copy size. In addition, the
recommended media should be used.
For example: the job requires that an A (A4) document be enlarged to a
C (A2) document. To have the title block be visible after folding, the A
(A4) document must be inserted as if it were a C (A2) document.
You may want to refer to "CUSTOM R/E PRESETS" in the "Main Menu,
COPY OPTIONS" section, and set up the
REDUCTION/ENLARGEMENT default to show the standard reduction
and enlargement. Set the reduction /enlargement to display A to C (A4
to A2) above the keys.
To ensure that the selected fold is made correctly, it is critical that the
document be centered on the Scanner Document Feed Tray when
scanning.
For additional folding and title block positioning information, refer to the
Folder Operator Manual or the Folding Supplement CD.
XEROX WIDE FORMAT COPY SYSTEM
Scanning when using a Folder · 53
When the Finisher key is pressed and the finishing options are selected
a new page icon is added to the READY TO COPY screen. The page
icon is displayed with a dotted box at one of the page corners. The
dotted box indicates the title block location selection made using the
Finisher menu. The title block location can be changed on this screen
using the Next and Previous keys. Refer to the Finisher Key section for
additional finishing information. The title block location icon will show
dotted line in all corners when the DON'T CARE option is selected.
Ready to Copy
Finisher Screen
READY TO COPY
INSERT DOCUMENT
AUTO
100.0 %
1
NOTE: Any of the finishing options can be changed during a Sets Build
job. The option(s) must be changed before the document to be copied is
inserted.
54 ·Scanning when using a Folder
XEROX WIDE FORMAT COPY SYSTEM
Scanning oversized documents
Scanning oversized documents
An oversized document is defined as any document that is larger in width
or length than a standard E-size (A0) document.
LONG DOCUMENTS
Operator assistance will be required to guide and control the position of a
long document to prevent it from skewing or moving from side-to-side as
it feeds through the scanner. Documents longer than 36 inches (914
mm) will always exit to the rear of the Scanner.
WIDE DOCUMENTS
Documents wider than 36 inches (914 mm) but less than 42 inches
(1057 mm) can be scanned. However, the scanned image area, of a
document centered on the Feed-in Tray, is 36 inches (914 mm). Any
image beyond the 36 inch (914 mm) width will be clipped off on the
output copy.
When a document wider than 36 inches (914 mm) is inserted into the
Document Handler, a message will be displayed to enter the scan width.
To scan the document, enter 36 in.(914 mm) then press the Enter key to
start the scan. A number larger than 36 (914) will not be accepted.
XEROX WIDE FORMAT COPY SYSTEM
Scanning oversized documents · 55
Special features keys
Special features keys
There are many enhanced features for making copies that meet special
needs. The keys that control these features are on the right side of the
Scanner Control Panel.
To enable a feature, press the applicable key. If the feature has an
associated screen, that screen is displayed when the key is pressed. If
any settings are changed from the default state, the corresponding
indicator lamp next to the key illuminates. Pressing the C/CA key on the
numeric keypad twice returns all settings for the feature to the default
state and the corresponding indicator lamp is extinguished.
When the settings for a feature are appropriately set, pressing the same
feature key causes the changes to be accepted and the system returns
to the READY state. Pressing a different feature key while editing a
setting is invalid and causes a beep. Pressing a different feature key
while not editing a setting causes the requested feature screen to be
displayed.
If a feature has no associated screen, pressing that feature key switches
the feature on (enabled) or off (disabled). When such a feature is
enabled, the corresponding indicator lamp is illuminated.
If the BEEP function (factory default) is enabled, a beep sound will be
heard when a key is pressed. If an improper key is pressed, a multiple
beep sound will be heard.
The illustration on the following page depicts the special features portion
of the Scanner Control Panel.
56 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
Transform
Sample
Batch
Sets Build
A B C
D E F
1
3
2
M N O
G H I
J K L
Finisher
6
4
5
W X Y
T U V
P R S
9
7
8
Store/
Recall
C/CA
/.
0
Start
Printer
Interrupt
Stop
Printer Interrupt key
Jobs on the WIDE FORMAT COPY SYSTEM have the following priority:
1. Any job currently printing
2. A copy job that is ready to print
3. A remote print job.
If a remote print job is in progress, a copy job (one or more images
captured by the Scanner), cannot normally use the Printer until the
remote print job has finished. The Printer Interrupt key enables you to
switch the copy priority from normal to high.
To process a copy job immediately, press the Printer Interrupt key. The
Printer Interrupt indicator lamp illuminates. The current pages of the
most current remote print job are completed. Usually a maximum of two
pages are printed. The print job is then suspended and you can run copy
jobs. When the copy jobs are finished, you can press the Printer
Interrupt key again. The Printer Interrupt indicator lamp is
extinguished. The interrupted remote print job resumes.
If you send no more copy jobs, press no keys, and scan no documents,
the Printer Interrupt feature is automatically disabled after a time set by
the PRINTER INTERRUPT timer. Refer to "Timers" in the "Main Menu,
CONFIGURATION" section for instructions about how to set this value.
The default value is 1 minute. It can be set to a value between 1 and 99
minutes.
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 57
Store/Recall key
The Store/Recall feature contains the following menu choices:
·
·
·
·
LAST JOB - Enables you to recall and reuse the information from
the last copy job.
JOB TEMPLATES - Enables you to save the settings from
previous jobs in memory as templates.
SAVE DEFAULT TEMPLATE - Enables you to save the settings
from the current job as the default template.
RECALL FACTORY DEFAULTS - Enables you to recall the
factory default settings as the active default settings.
To access the STORE/RECALL menu:
1. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed. The black arrows indicate that the menu contains
more options than are visible. The selected option is highlighted.
STORE/RECALL
LAST JOB
JOB TEMPLATES
SAVE DEFAULT TEMPLATE
2. Press the Previous or Next key to scroll through the list of
options.
3. When the desired option is highlighted, press the Enter key to
select the option. The menu or screen for the selected option is
displayed.
The LAST JOB option of the STORE/RECALL menu provides a sub-
menu of the following choices:
Last Job
·
RECALL LAST JOB - Enables you to recall and reuse the
parameters, images, and features associated with the last copy
job. You can either reprint the last job or print a new job using all
of the recalled settings. If you desired, the recalled settings could
be changed without scanning the job again.
·
DELETE LAST JOB - Enables you to delete the information from
the last job.
NOTE: In the SCAN mode, the Last Job option is not available.
To access the LAST JOB menu:
1. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed.
58 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
2. Press the Enter key to select LAST JOB. The LAST JOB menu
screen is displayed. The selected option is highlighted.
LAST JOB
RECALL LAST JOB
DELETE LAST JOB
3. Press the Previous or Next key to highlight the desired option.
4. Press the Enter key to select the highlighted option. The screen
for the selected option is displayed.
Use the RECALL LAST JOB option to recall the information from the last
job.
Recalling the Last Job
To recall the last job information:
1. Press the Store/Recall key. The Store/Recall menu screen is
displayed.
2. Press the Enter key to select LAST JOB. The LAST JOB menu
screen is displayed.
3. Press the Enter key to select RECALL LAST JOB. The screen
shown below is displayed.
COPIER PARAMETERS AND IMAGES
FOR LAST JOB RECALLED
PRESS ENTER TO
4. Press the Enter key to return to the READY screen.
You can now use the settings as they have been recalled, or you can
change one or more of them.
NOTE: The recalled job must be printed or cleared before the next
document can be scanned. If there is no last job to be restored, as is the
case at power up or after the last job has been deleted, a warning
message will advise you.
If, for security reasons, the parameters and images of the last job should
not be left stored, use the DELETE LAST JOB option.
Deleting the Last Job
To delete the information from the last job:
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 59
1. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed.
2. Press the Enter key to select LAST JOB. The LAST JOB menu
screen is displayed.
3. Press the Next key to highlight DELETE LAST JOB.
4. Press the Enter key to select DELETE LAST JOB. A delete
confirmation screen is displayed. The default response is NO.
DELETE LAST JOB
ARE YOU SURE ?: NO
5. Press the Previous or Next key to change the response to YES.
6. Press the Enter key to confirm the deletion. The screen shown
below is displayed. The last job images and parameters are
deleted.
JOB PARAMETERS AND IMAGES
FOR LAST JOB DELETED
PRESS ENTER TO CONTINUE
7. Press the Enter key to return to the READY screen.
The JOB TEMPLATES option of the STORE/RECALL menu provides a
sub-menu of the following choices:
Job Templates
·
·
·
RECALL TEMPLATE - Enables you to recall saved settings.
SAVE TEMPLATE - Enables you to save job settings in memory.
DELETE TEMPLATE - Enables you to delete saved settings.
To access the JOB TEMPLATES menu:
1. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed.
2. Press the Next key to highlight JOB TEMPLATES.
3. Press the Enter key to select JOB TEMPLATES. The JOB
TEMPLATES menu screen is displayed. The selected option is
highlighted.
60 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
JOB TEMPLATES
RECALL TEMPLATE
SAVE TEMPLATE
DELETE TEMPLATE
4. Press the Previous or Next key to highlight the desired option.
5. Press the Enter key to select the highlighted option. The screen
for the selected option is displayed.
The RECALL TEMPLATE option allows you to recall job parameters that
were previously saved as templates and use them for the current job.
Recalling Job
Templates
To recall a template:
1. Press the Store/ Recall key. The STORE/RECALL menu
screen is displayed.
2. Press the Next key to highlight JOB TEMPLATES.
3. Press the Enter key to select JOB TEMPLATES. The JOB
TEMPLATES menu screen is displayed.
4. Press the Enter key to select RECALL TEMPLATE. The
RECALL TEMPLATE screen is displayed. The storage locations
that actually contain templates are shown. Locations that do not
contain a template are not shown.
Below is an example of the RECALL TEMPLATE screen.
RECALL TEMPLATE
TEMPLATES IN USE:
ENTER TEMPLATE NUMBER
1
2
0
3
4
5
5. Use the numeric keypad to enter the location of the template to
be recalled.
6. Press the Enter key to confirm your choice. A recall
confirmation screen is displayed. The associated template is
recalled and the Scanner Control Panel settings are configured
accordingly.
JOB PARAMETERS RECALLED
PRESS ENTER TO CONTINUE
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 61
You can now use the parameter settings as they have been recalled, or
you may change some of them.
NOTE: If you change any of the Image Quality settings (i.e., document
type, background suppression, or copy contrast) or if you want to invert
the image, an error message will advise you to rescan the image. You
must rescan the image to change any image quality settings for a job
that has been recalled.
7. Press the Enter key to return to the READY screen.
The SAVE TEMPLATE option allows you to save groups of settings
associated with a job in memory as templates. Up to nine such
templates can be saved.
Saving Job Templates
To save a job template:
1. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed.
2. Press the Next key to highlight JOB TEMPLATES.
3. Press the Enter key to select JOB TEMPLATES. The JOB
TEMPLATES menu screen is displayed.
4. Press the Next key to highlight SAVE TEMPLATE.
5. Press the Enter key to select SAVE TEMPLATE. The SAVE
TEMPLATE screen is displayed. It shows the unused template
locations. Locations that contain a template already are not
shown.
Below is an example of the SAVE TEMPLATE screen.
SAVE TEMPLATE
UNUSED TEMPLATES: 6 7 8 9
ENTER TEMPLATE NUMBER:
0
6. Choose an unused location and use the numeric keypad to enter
its location.
7. Press the Enter key to confirm your location choice. The
settings from the current copy job are saved at the location
entered and a save confirmation screen is displayed.
JOB PARAMETERS SAVED
PRESS ENTER TO CONTINUE
62 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
NOTE: You can replace the contents of a used location with the current
job settings information. If you choose a location that already contains
information, the TEMPLATE IS IN USE screen is displayed as shown
below. Press the Enter key to overwrite the contents. Press the Exit key
to cancel the operation.
TEMPLATE IS IN USE
PRESS ENTER TO CONTINUE
EXIT TO ABORT
8. Press the Enter key to return to the READY screen.
Use the DELETE TEMPLATE option to delete previously saved
templates. Doing so leaves the template location blank and available to
use again. Once a template has been deleted, it cannot be recalled.
Deleting Job Templates
To delete a saved template:
1. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed.
2. Press the Next key to highlight JOB TEMPLATES.
3. Press the Enter key to select JOB TEMPLATES. The JOB
TEMPLATES menu screen is displayed.
4. Press the Next key until DELETE TEMPLATE is highlighted.
5. Press the Enter key to select DELETE TEMPLATE. The
DELETE TEMPLATE screen is displayed. This screen indicates
the locations for the templates currently in use. Locations that
do not contain a template are not shown.
Below is an example of the DELETE TEMPLATE screen.
DELETE TEMPLATE
TEMPLATES IN USE: 1 2 3 4 5
ENTER TEMPLATE NUMBER:
0
6. Use the numeric keypad to enter the location of the template to
be deleted, then press the Enter key. The deleted location is
removed from the list in the DELETE TEMPLATE screen and the
contents of that location are deleted.
You can now select other locations to be deleted in the same way.
7. If no more locations are to be deleted, press the Exit key to
return to the READY screen.
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 63
The SAVE DEFAULT TEMPLATE option of the STORE/RECALL menu
enables you to save the settings for the current job as the default
settings. Each additional job will then have these settings established as
the default selections.
Save Default
Template
To save the current job settings as the default template:
1. Ensure that all the options under Media Selection, Image
Quality, and Reduce/Enlarge are set as desired. Make any
necessary changes.
2. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed.
3. Press the Next key until SAVE DEFAULT TEMPLATE is
highlighted.
4. Press the Enter key to select SAVE DEFAULT TEMPLATE. A
confirmation screen is displayed indicating that the job
parameters have been saved.
JOB PARAMETERS SAVED
PRESS ENTER TO CONTINUE
5. Press the Enter key to return to the READY screen.
The factory default job settings are permanently stored in memory. The
RECALL FACTORY DEFAULTS option of the STORE/RECALL menu
enables you to recall the factory default settings as the active default
settings.
Recall Factory
Defaults
To recall the factory default settings:
1. Press the Store/Recall key. The STORE/RECALL menu screen
is displayed.
2. Press the Next key until RECALL FACTORY DEFAULTS is
highlighted.
3. Press the Enter key to select RECALL FACTORY DEFAULTS.
The factory default settings are immediately recalled. A
confirmation screen is displayed.
JOB PARAMETERS RECALLED
PRESS ENTER TO CONTINUE
4. Press the Enter key to return to the READY screen.
64 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
Finisher key
A finishing device, such as a folder, can be connected to the WIDE
FORMAT COPY SYSTEM If such a device is connected, the Finisher
key enables or disables that device.
To enable/disable a finishing device:
1. Press the Finisher key. The Finisher indicator lamp illuminates
and the FINISHER menu screen are displayed. The black
arrows indicate that the menu contains more options than are
visible. The selected option is highlighted.
FINISHER
FOLD PROGRAM
TITLE BLOCK LOCATION
OUTPUT BIN
OVERLENGTH OPTION
TAB OPTIONS
NOTE: If no finishing device is connected, pressing the Finisher key
produces the error message shown below.
FINISHER
FINISHER OPTION
IS NOT AVAILABLE
When a set is being built, the finisher options cannot be changed and
pressing the Finisher key is invalid. The error screen shown below is
displayed. Enable the finisher and select the finisher options either
before selecting the Sets Build option or after the set has been built.
FINISHER
FINISHER OPTION CANNOT BE CHANGED
DURING SETS BUILD OPERATION
For either error screen, press the Exit key to return to the READY
screen. The Finisher indicator lamp is extinguished
2. Press the Previous or Next key to scroll through the list of
options.
3. When the desired option is highlighted, press the Enter key to
select the option. The screen for the selected option is
displayed. See Finisher menu options below and on the next
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 65
page for an illustration and description of each option. Also refer
to the Folder User Documentation for additional information on
the available folding options.
4. Press the Previous or Next key to scroll through the choices for
the selected option.
5. When the desired choice is highlighted, press the Enter key to
confirm your selection.
6. Repeat steps 4 and 5 if you want to change a setting for any
other options.
7. Press the Exit key to return to the READY screen.
A page icon is displayed with a dotted box at one of the page corners.
The dotted box indicates the title block location selection made using the
Finisher menu. The title block location can be change on this screen
using the Next and Previous keys.
READY TO COPY
INSERT DOCUMENT
AUTO
100.0 %
1
8. To disable the finisher, press the Finisher key again. The
Finisher indicator lamp is extinguished.
Below are descriptions of each of the Finisher menu options. Refer to the
Finisher user documentation for additional information on these options.
Finisher menu
options
The FOLD PROGRAM option enables you to select one of up to 20 user-
defined programs. The program names are programmed into the finisher
and passed to the Controller when the finisher goes through its power-up
sequence.
FOLD PROGRAMS
FOLD PROGRAM
PROGRAM:
USER PROGRAM
The OVERLENGTH OPTIONS option enables you to specify how long
documents (documents over 80 inches long) are handled by the folder.
The choices are NO FOLD and Z-FOLD. If NO FOLD is selected, the
long document will not be folded. If Z-FOLD is selected, the long
document will be Z-FOLDED, but not cross-folded. NO FOLD is the
factory default setting.
OVERLENGTH
OPTIONS
66 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
OVERLENGTH OPTIONS
OVERLENGTH: NO FOLD
The TAB OPTIONS option enables you to override the pre-programmed
tab settings for the selected finishing program. The choices are
ALWAYS ON, ALWAYS OFF, and USE PROGRAM SETTING. USE
PROGRAM SETTING is the factory default setting.
TAB OPTIONS
TAB OPTIONS
TAB:
USE PROGRAM
The PUNCH OPTIONS option enables you to override the pre-
programmed hole punch settings for the selected finishing program. The
choices are ALWAYS ON, ALWAYS OFF, and USE PROGRAM
SETTING. USE PROGRAM SETTING is the factory default setting.
PUNCH OPTIONS
PUNCH OPTIONS
PUNCH:
USE PROGRAM
The MARGIN OPTIONS option enables you to override the pre-
programmed margin settings for the selected finishing program. The
choices are ALWAYS OFF and USE PROGRAM SETTING. Note that
ALWAYS ON is not an available setting. USE PROGRAM SETTING is
the factory default setting.
MARGIN OPTIONS
MARGIN OPTIONS
MARGIN:
USE PROGRAM
The CROSSFOLD OPTIONS option enables you to override the pre-
programmed crossfold settings for the selected finishing program. The
CROSSFOLD OPTIONS
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 67
choices are ALWAYS ON, ALWAYS OFF, and USE PROGRAM
SETTING. USE PROGRAM SETTING is the factory default setting.
CROSSFOLD OPTIONS
CROSSFOLD:
USE PROGRAM
The TITLE BLOCK LOCATION option enables you to specify the location
of the title block for the copy jobs that are about to be run. The choices
are BOTTOM RIGHT, BOTTOM LEFT, TOP RIGHT, TOP LEFT, and
INTELLIGENT TITLE BLOCK. BOTTOM RIGHT is the factory default
setting.
TITLE BLOCK
LOCATION
INTELLIGENT TITLE BLOCK should be used if the title block is not
located in the desired location on the folded copy. This selection will use
information, document size, selected fold program, title block position
input to place the title block in a position based on the information. It may
not be the user's desired or location. Before making this selection, check
the following:
·
·
·
·
Autorotate is selected.
Document being scanned is oriented correctly for scanning.
Ensure the title block position specified is correct.
For additional help, refer to the Folding Supplement manual.
NOTE: The title block location may also be selected on the READY TO
COPY screen using the title block location icon. The title block location is
indicated by the dotted lines.
TITLE BLOCK LOCATION
TB LOCATION:
BOTTOM RIGHT
68 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
The OUTPUT BIN option enables you to specify which finisher output bin
to use for the finished output. The choices are DON'T CARE, BIN X
(where X equals 1 to the actual number of finisher bins), FANFOLD, and
BYPASS. BYPASS is the factory default setting.
OUTPUT BIN
OUTPUT BIN
OUTPUT BIN:
BYPASS
Sets Build key
The Sets Build mode allows you to scan a series of images and build an
electronically collated set. Once the set is built, one or more collated
copies can be printed.
NOTE: The Sets Build mode is not available unless the WIDE FORMAT
COPY SYSTEM is in the COPY mode.
NOTE: Any of the finishing options can be changed during a Sets Build
job. The option(s) must be changed before the document to be copied is
inserted.
In Sets Build mode, documents of C (A2) size and larger are normally
delivered to the rear of the Scanner after the scan. If the DOCUMENT
RETURN parameter is set to REAR, then all documents are delivered to
the rear after scanning. The WIDE FORMAT SCAN SYSTEM is
equipped with a document catching device, called the Stacker, to receive
these documents. Refer to "Scanner Control" in the "Main Menu" section
of this manual for further information about the DOCUMENT RETURN
parameter.
Preparing to build the
set
To build a collated set:
Building and printing
the set
1. Press the Sets Build key. The Sets Build indicator lamp
illuminates and the SETS BUILD screen are displayed.
SETS BUILD
COLLATION: FORWARD
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 69
2. Press the Previous or the Next key to select FORWARD or
REVERSE collation.
·
FORWARD prints the collated set in the order that the sheets
were scanned. Page 1 will be on the top.
1
1
2
2
3
3
PRINTED
SCANNED
·
REVERSE prints the set in the reverse order that they were
scanned. Page 1 will be on the bottom.
1
3
2
2
3
1
SCANNED
PRINTED
3. Press the Enter key to confirm your choice. The READY TO
BUILD SET screen is displayed.
READY TO BUILD SET
INSERT DOCUMENT: 1
AUTO
MEMORY
100.0
%
4. Insert each document of the set one at a time into the Scanner
as prompted by the display. As the documents are scanned, the
amount of memory used is shown in the rectangular graphical
display.
NOTE: You can select reduction/enlargement and copy quality settings
for each sheet prior to scanning that sheet.
5. When the set is completely scanned, press the Sets Build key
again. The Sets Build indicator lamp is extinguished when the
Start key is pressed then the READY TO PRINT SET screen is
displayed.
READY TO PRINT SET
PRESS START TO PRINT
100.0
3
6. If desired, you can now make further changes to the Media
Selection, Source selection and the Reduction/Enlargement
value. Any such change will be applied to that printing of the
entire set.
70 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
7. Enter the number of copies desired and press the Start key.
The Printer prints the number of sets requested.
NOTE: In COLLATION FORWARD only, an extra set is made as a check
plots set.
After the printing of the set, the set can be recalled, the values changed
again, and the set reprinted using the new values. To recall the set, refer
to "Store/Recall key" in the "Special features key" section of this manual
for further information.
Batch key
The Batch feature allows you to improve copy speed by enabling Batch
Mode processing of several documents on the Scanner. When Batch
Mode processing is enabled, the Scanner collects prescan information
for just the first document inserted into the Scanner. Prescan information
on subsequent documents in the set is not collected. The subsequent
documents will be scanned using the information collected on the first
document. Eliminating the collection of this information increases overall
copy speed.
To enable Batch Mode processing:
1. Press the Batch key. The Batch indicator lamp will begin
flashing.
2. Insert the first original into the Scanner. The Scanner scans the
original and the screen shown below is displayed.
WIDTH FOUND FOR SET IS XX.X
INPUT ANOTHER WIDTH OR
PRESS ENTER TO ACCEPT
3. Do one of the following:
Use the numeric keypad to enter the width of the set and press the Enter
key to accept the value.
Press the Enter key to accept the width detected by the WIDE FORMAT
COPY SYSTEM.
The Batch indicator lamp becomes steady and remains so until batch
mode is disabled.
4. When the last document in the set has been scanned, press the
Batch key to disable batch mode. The Batch indicator lamp is
extinguished.
NOTE: When Batch mode is ENABLED, the AUTOCENTER feature is
temporarily disabled. Be careful to manually center each document that
is inserted into the Scanner
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 71
Transform key
The Transform feature contains the following menu choices:
·
MARGINS - Allows you to adjust the dimensions of the margins
around the image. By entering positive margins, blank space is
inserted around the image. By entering negative values,
unwanted parts of the image can be cropped.
·
·
JUSTIFICATION - Allows you to adjust the position of the image
on the media.
TRANSFORM - Allows you to request transformation of the
scanned image into a mirror image, a negative photographic
inversion, or both.
NOTE: The image can also be rotated. Refer to "Imaging" in the "Copy
Options" section for further information about image rotation.
To access the TRANSFORM MENU:
1. Press the Transform key. The TRANSFORM MENU screen is
displayed. The selected option is highlighted.
TRANSFORM MENU
MARGINS
JUSTIFICATION
TRANSFORM
2. Press the Previous or Next key to highlight the desired option.
3. Press the Enter key to select the highlighted option. The screen
for the selected option is displayed.
The MARGINS option of the TRANSFORM MENU allows you to select
the dimensions for the margins that surround an image. These margins
are referred to as the lead, left, right and trail edges.
Margins
NOTE: Margins can only be adjusted when the WIDE FORMAT COPY
SYSTEM is in the COPY mode.
The example below illustrates an image entering the Scanner and the
orientation of the image margins.
Scanner
Lead
Right image
Left image
Trail
72 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
Margins are added to the image in one of two ways:
·
If Synchro has been selected from the Output Format area of
the Scanner Control Panel, the lead margin is added before the
image is printed. The trail margin is added after the media cut
signal is received from the Scanner. Thus, the length of the
media from the Printer will be the scanned document length plus
the lead and trail margins.
·
If a fixed media length (Preset or Manual) has been selected as
the Output Format, the white space of the specified margin
surrounds the image, but the actual physical dimensions of the
media remain as specified. The margins reduce the allowable
area on the media in which the image may be placed.
To adjust the margins for an image:
1. Press the Transform key. The TRANSFORM MENU screen is
displayed.
2. Press the Enter key to select MARGINS. A screen displaying
the settings for each margin is displayed. Below is an example
of the screen.
LEAD
LEFT
RIGHT
+ 1.0 IN
+ 0.0 IN
+ 0.0 IN
+ 0.0 IN
TRAIL
If the unit of measure has been set to inches, "IN" appears next to each
value. If the unit of measure has been set to millimeters, "MM" appears
next to each value. Refer to "Localization" in the "Main
CONFIGURATION " section for information about setting the display
units.
The graphical display to the right of the margin settings illustrates the
approximate placement of the image as a result of the settings.
3. Press the Previous or Next key to highlight the setting you wish
to change.
NOTE: Each margin has two components. They are a "+/-" indicator
and a numeric value. As you press the Previous or Next key, the
components highlight individually.
4. Press the Enter key to select the setting.
5. Change the setting as follows:
·
To change the "+" or "-" setting, press the Previous or Next key.
n edge of the image can be clipped by entering a negative
margin value for that edge. In that case, the affected edge is
shown as a dotted line and the image icon is shown as partially
outside the bounds of the media.
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 73
LEAD
LEFT
RIGHT
TRAIL
+ 1.0 IN
- 1.0 IN
+ 0.0 IN
+ 0.0 IN
The illustration below shows a negative left margin with TOP LEFT
justification.
·
To change the value setting, use the numeric keypad to enter the
value. The values can be set in increments of 0.1 in (1.0 mm)
and over a range of +4 to -4 in (+100 to -100 mm). Values
outside the allowed range are rejected. If you enter an invalid
value, press the Exit key to clear it. The default margins are 0.
6. Press the Enter key to confirm the setting. The graphical display
updates accordingly
NOTE: To cancel the setting, press the Exit key
7. When you have set all the margins as desired, press the Exit
key to return to the TRANSFORM MENU screen.
The JUSTIFICATION option of the TRANSFORM MENU allows you to
adjust the position of the image on the media.
Justification
NOTE: "Image" means the entire scanned page including the white
space.
To specify the image position:
1. Press the Transform key. The TRANSFORM MENU screen is
displayed.
2. Press the Next key to highlight JUSTIFICATION.
3. Press the Enter key to select JUSTIFICATION. The
JUSTIFICATION screen is displayed. This screen shows the
current settings for the X and Y coordinates. It also includes a
graphical display of the approximate position of the image as a
result of the settings.
Below is an example of the JUSTIFICATION screen.
JUSTIFICATION
X:
Y:
LEFT
CENTER
74 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
4. Press the Previous or the Next key to select the X (horizontal)
or Y (vertical) coordinate.
5. Press the Enter key to confirm your choice.
6. Press the Previous or Next key to select a choice for
justification.
For the X direction, the choices are LEFT, CENTER, and RIGHT. For
the Y direction, the choices are TOP, CENTER, and BOTTOM.
7. Press the Enter key to confirm your choice. The graphical
display updates accordingly.
NOTE: To cancel your choice, press the Exit key.
8. Repeat steps 4 through 7 if you wish to change position of the
other coordinate.
9. Press the Exit key to return to the TRANSFORM MENU screen.
The TRANSFORM option of the TRANSFORM MENU allows you to
create a mirror image of a scanned image and to convert a scanned
image to a negative image.
Transform
The MIRROR option allows you to create a mirror image of a scanned
image.
Creating a Mirror Image
To create a mirror image:
1. Press the Transform key. The TRANSFORM MENU screen is
displayed.
2. Press the Next key until TRANSFORM is highlighted.
3. Press the Enter key to select TRANSFORM. The TRANSFORM
screen is displayed.
Below is an example of the TRANSFORM screen with both the MIRROR
and INVERT options turned off.
TRANSFORM
MIRROR:
INVERT:
OFF
OFF
4. Press the Enter key to select MIRROR.
5. Press the Previous or Next key to select the desired
transformation. Four choices are available - X, Y, XY, and OFF.
Table 4 below graphically depicts the choices.
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 75
Table 4. Mirror transformations
Axis
X
Transform
Y
XY
OFF
6. Press the Enter key to confirm your choice. The graphical
display updates accordingly. The illustration below shows the
TRANSFORM screen with "X" as the mirror image selection.
TRANSFORM
MIRROR:
INVERT:
X
OFF
NOTE: To cancel your choice, press the Exit key
7. Press the Exit key to return to the READY screen.
The INVERT option allows you to convert a scanned image to a negative
image. For black and white images, the white pixels will be printed black
and the black pixels will be printed white. For grayscale images, the
image will be converted into its photographic negative. INVERT is not
selectable when Color is selected as an Original, Type.
Inverting an Image
To invert an image:
1. Press the Transform key. The TRANSFORM MENU screen is
displayed.
2. Press the Next key until TRANSFORM is highlighted.
3. Press the Enter key to select TRANSFORM. The TRANSFORM
screen is displayed.
Below is an example of the TRANSFORM screen with both the MIRROR
and INVERT options turned off.
76 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
TRANSFORM
MIRROR:
OFF
OFF
INVERT:
4. Press the Next key to highlight INVERT.
5. Press the Enter key to select INVERT.
6. Press the Previous or Next key to turn the option ON or OFF.
7. Press the Enter key to confirm your choice. The graphical
display updates accordingly.
When INVERT is ON, the icon on the right side of the TRANSFORM
screen is inverted. The example below shows the TRANSFORM screen
with INVERT turned ON.
TRANSFORM
MIRROR
INVERT
OFF
ON
NOTE: To cancel your choice, press the Exit key.
8. Press the Exit key to return to the READY screen.
Sample key
The Sample key allows you to print a sample of a scanned image in both
the COPY mode and the SCAN mode. You can then check the sample
for quality or observe the results of features or copy quality adjustments
before document is copied or scan to a file.
The dimensions of the sample, in the Copy mode, are the width of the
page by 210 mm. The sample is taken from a point equidistant from the
lead and trail edge of the image. Refer to Copy Mode below for
instruction to print a sample.
In the SCAN mode the sample size is the whole document. To enable
the Sample key in the SCAN Mode, the Scan-to-net feature must be
installed. To enable a print sample the Scan-to-print feature key must be
installed. Refer to Scan Mode Sample below for instructions to print a
sample.
To print a sample of a scanned image:
Copy Mode Sample:
1. Press the Sample key. The Sample indicator lamp illuminates.
The Scanner Control Panel is placed in Printer Interrupt mode
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 77
and the Printer Interrupt indicator lamp illuminates. The Printer
immediately prints a sample of the next image inserted into the
Scanner. The SAMPLE MODE screen is displayed.
SAMPLE MODE
PRESS START TO ACCEPT PAGE.
PRESS C/CA TO REJECT.
2. Do one of the following:
·
Press the Start key to print the complete image as a full-size
copy.
·
Press the C/CA key to delete the scanned image.
3. Press the Sample key again to disable the Sample feature. The
Printer is returned to the default priority setting and the Sample
and Printer Interrupt indicator lamps are extinguished.
The best sample prints will be produced if the image enhancement
features have been enabled. Refer to the Image Quality section for more
information.
Scan Mode Sample:
In order to have the selections indicated below in the SAMPLE MODE
screen, the Scan-to-Net feature key must be installed to get SCAN
IMAGE TO FILE, and the Scan-to-Print Feature key must be installed to
get SCAN IMAGE TO PRINTER. The Scan-to Print feature is useful on
the X2 TECH that does not have a COPY Mode. However it is
convenient on the other WIDE FORMAT COPY SYSTEMS to be able to
make a sample before scanning an image to file.
To print a sample copy, perform the following:
1. If the scanner is set to COPY mode switch to SCAN mode for
instructions, refer to “Switching between COPY mode and SCAN
mode”
2. Enter the Directory name.
3. Press the Sample special function key. The SAMPLE MODE
screen is displayed.
SAMPLE MODE
SCAN IMAGE TO FILE
4
SCAN IMAGE TO PRINTER
4. Press the Next key to highlight SCAN IMAGE TO PRINTER.
NOTE: The SCAN IMAGE TO FILE and SCAN IMAGE TO PRINTER
options can be individually or simultaneously selected. However, you
cannot deselect both options
78 ·Special features keys
XEROX WIDE FORMAT COPY SYSTEM
5. Press the Enter key to enable SCAN IMAGE TO PRINTER.
Press the Exit key to exit the menu.
The processing time for Scan to Printer images will be longer, depending
on the image size.
XEROX WIDE FORMAT COPY SYSTEM
Special features keys · 79
Scanning to the Network (SCAN
mode)
Scanning to the Network (SCAN
mode)
The WIDE FORMAT COPY SYSTEM has two scanning modes of
operation: COPY mode and SCAN mode.
NOTE: The SCAN mode is optional on the XEROX WIDE FORMAT
COPY SYSTEM 8825. X2 TECH Color Scan-to-Net is an available
option for all XEROX WIDE FORMAT COPY SYSTEM equipped with the
WIDE FORMAT SCAN SYSTEM. The Color Scan-to-Net feature requires
a separately purchased, Color Enablement feature key. Scanned color
files may be printed in color on the X2 TECH printer. For ordering
information, contact your XEROX representative.
NOTE: The COPY mode will be disabled and the READY TO COPY
screen will not be accessible when the SCAN OPTION (COLOR) is
enabled and a color printer is connected to the Controller.
·
In COPY mode, documents are scanned and temporarily stored
in memory or on the controller internal hard disk, and then sent
to the local Printer as soon as the Printer is available. When the
next job is scanned, the file from the previous job is automatically
deleted from the hard disk, making room for new files. Operation
of the system works as described in the previous sections.
·
In SCAN mode, the image file created by scanning is stored
directly on the controller hard disk for later retrieval over a
connected network by a remote system. The image is stored in
Tagged Image File Format (TIFF) 6.0 using CCITT Group 4,
CALS compression, Packbits, or PDF. High resolution JPG files
are also available with the Color Scan-to-Net option.
Files stored in SCAN mode can be retrieved over the network. After the
AccXES Client Tools program running on a network-connected computer
retrieves the file, the image residing on the local hard disk is deleted
XEROX WIDE FORMAT COPY SYSTEM
Scanning to the Network (SCAN mode) · 81
automatically. For more information, refer to the AccXES Client Tools
User Guide.
Other remote retrieval programs can use the File Transfer Protocol (FTP)
to retrieve and delete files from the WIDE FORMAT COPY SYSTEM
hard disk over the network. These other programs will copy the files
rather than move them, so the files remain on the local hard disk after
retrieval.
After a file has been on the local hard disk for longer than the time
specified for the FILE DELETION Timer, the system automatically
deletes the file. Refer to the Main Menu, CONFIGURATION menu,
TIMERS section of this manual for information about setting the FILE
DELETION timer.
Switching between COPY mode and
SCAN mode
NOTE: The COPY mode will be disabled and the READY TO COPY
screen will not be accessible when a color printer is connected to the
Controller.
To switch between the COPY mode and the SCAN mode, perform the
following steps:
1. Ensure that the READY TO COPY screen is displayed. If a
menu is displayed, press the Menu key to return to the READY
screen. If PLEASE ENTER ACCOUNT is displayed, enter a
valid User ID code then enter a valid account number to obtain
the READY screen.
2. Press the Mode key. The system switches to the SCAN mode
and the screen now displays. Pressing the Mode key again
returns the system to the COPY mode.
PLEASE ENTER
DIRECTORY
Images
3. Enter a Directory name, up to 16 alphanumeric characters, to
which you will scan the images. The name cannot begin with a
period/decimal point.
NOTE: The TCP/IP network protocol must be enabled in the Controller
or the WIDE FORMAT COPY SYSTEM will not enter the SCAN mode.
To enable the TCP/IP protocol, refer to the Controller Setup Manual.
82 ·Scanning to the Network (SCAN mode)
XEROX WIDE FORMAT COPY SYSTEM
Understanding the READY TO SCAN
screen
Below is an example of the READY TO SCAN screen. Following the
example are descriptions of the special information displayed on the
screen.
READY TO SCAN
INSERT DOCUMENT
TIFF/CCITTG4
400
1 BIT
TIFF/CCITTG
41 BIT
This area indicates the selected file format. Refer to
SCAN OPTIONS (LINE) or SCAN OPTIONS (PHOTO)
or SCAN OPTIONS (COLOR) to set these options. The
available options will differ depending upon your Scan
Option selection.
This area shows the selected scanning resolution.
Press the Previous or Next key to select a value of 100,
200, 300, or 400 DPI (Dots Per Inch). A new value can
be selected before each scan.
This icon shows how much Random Access Memory (RAM)
is in use by the scanned file. As space is used, the dark area
increases. After the scan is complete, the file is processed
and then moved to the internal hard disk. The RAM space
then becomes available again.
This icon shows how much hard disk space is in use by
stored files. As space is used, the dark area increases.
When files are moved off the disk over the network to
remote devices, the space becomes available again. Files
are also deleted when the age of the file exceeds the value
set in the timer. Refer to "Timers" in the "Main Menu"
section to set this value. The factory default is 24 hours.
Selections disabled in SCAN mode
Certain selections available in COPY mode are not available in SCAN
mode. The unavailable selections are:
·
·
Sets Build - In SCAN mode each document has a separate
image stored on the disk. Each image is separately retrieved at
the remote device. Images cannot be grouped in sets.
Specifying the media Source and Type - Since the output is now
an electronic file, specifying the media is not applicable.
XEROX WIDE FORMAT COPY SYSTEM
Scanning to the Network (SCAN mode) · 83
·
·
Specifying the output format - The image file always has the
format of the length of the document by the scan width. The
scan width can be manually specified, if the entire width of the
document is not desired. Refer to "Scanner Control" in the "Main
Menu" section to enable or disable manual specification of the
scan width.
Selection of Margins or Justification - You can crop equal
amounts from each side edge of the document by manually
specifying a scan width that is narrower than the actual
document. Refer to "Scanner Control" in the "Main Menu"
section to enable or disable manual specification of the scan
width.
·
·
·
Specification of Finishing Options - Since there is no physical
output, the finishing operations are not applicable.
Selection of Reduce/Enlarge - The electronic file is saved
without alteration, so all scanned information is preserved.
Selection of Image Type. Only Line ,Photo, Normal, and Color
image types are valid for SCAN mode. Refer to the "Image
Quality", "Scan Mode" section in this manual for additional
information
·
Background Suppression - This selection is automatically
switched to off if a color printer is connected.
Operating in SCAN mode
To scan documents for later retrieval over the network:
1. If job accounting is enabled, enter in your User ID and Account
ID when prompted and press Enter. If job accounting is not
enabled, you will not have to enter your IDs.
2. If you want to see a preview of the scanned images when they
are retrieved from the Controller to your workstation, verify that
the scanner's default "PREVIEW" box is checked when selecting
the Original, Type Use the Previous, Next, and Enter keys to
enable PREVIEW. Use the Enter key to confirm your choice(s).
3. With READY TO COPY displayed on the Scanner Control Panel,
press the Mode key to display READY TO SCAN.
4. Use the keypad on the Scanner Control Panel to enter in your 16
alphanumeric character Scan Directory name.
84 ·Scanning to the Network (SCAN mode)
XEROX WIDE FORMAT COPY SYSTEM
NOTE: To print a Sample in the next Step on an X2 TECH, the Scan-to-
print feature key must be installed. For more information, refer to the
Sample key section, Scan Mode Sample.
5. To view a sample of the file before it is scan to a file, Press the
Sample key on the Control Panel. Use the Next or Previous key
to highlight SCAN TO PRINTER and press the Enter key. Press
the Exit key to return to the READY screen, then press Start. A
copy will be sent to the printer.
6. When the Scanner Control Panel displays READY TO SCAN,
select your desired scanning resolution using the Next and
Previous keys.
NOTE: When making a color scan, be sure to select Color with the
arrow key under Image Quality on the Scanner Control Panel. The
Normal and Photo lights will be on.
7. Select the Image Quality, Original, Type by pressing the arrow
button located under Type. When the Type (Normal, Line,
Photo,or Color) is selected the appropriate SCAN OPTION
(NORMAL, LINE, PHOTO, or COLOR) is displayed. Use the
Next, Previous, and Enter keys to navigate to and through the
avaliable options on the screen. Press the Enter key to confirm
your choice(s). For additional information refer to the "Image
Quality, Scan Mode" section of this manual.
8. Insert your original document face down and centered on the
feed tray of the Scanner.
9. Gently move your document forward until the Scanner's feed
rolls engage the document's leading edge.
10. If prompted to do so, enter the desired scanning width and press
Enter.
11. As your document is automatically fed into the Scanner, the
resulting image is stored as a file in the Scan Directory on the
system Controller's hard drive. The image can be retrieved at
your workstation using the Retrieve Tool of the AccXES Client
Tools.
NOTE: You may have to press the Start button if the configuration (for
Auto Scan) has been changed from the factory default.
XEROX WIDE FORMAT COPY SYSTEM
Scanning to the Network (SCAN mode) · 85
Clearing the scanned images
The C/CA key enables you to remove scanned images from the WIDE
FORMAT COPY SYSTEM hard disk.
To clear scanned images:
1. Press the C/CA key. The CLEAR SCANNED IMAGE screen is
displayed.
CLEAR SCANNED IMAGE
DO NOT CLEAR IMAGE
2. Press the Previous or Next key to highlight the desired
selection.
3. Press the Enter key to select the highlighted selection. The
choices are:
·
·
DO NOT CLEAR IMAGE - The image is not deleted.
CLEAR LAST IMAGE - The last image scanned by the currently
active account is deleted. Press the C/CA key again, followed
by the Enter key, to delete the next-to-last scanned image. This
process can be repeated until all desired images are removed
from the hard disk. It may take a few minutes longer to clear a
scanned photo or an image with color.
NOTE: It is not possible to skip images. For example, it is not possible
to leave the last image scanned, but delete the next-to-last image
scanned. Photo and Color mode scans may take a few minutes to clear.
·
CLEAR ALL IMAGES - All images stored under the currently
active account are deleted.
Managing the file system
The file system stores images in directories on the internal hard disk
drive. The images are stored in the Directory specified by the user
when entering the SCAN mode. The default directory is "images".
Managing the file system requires the System Administrator password.
The FILE SYSTEM option of the SYSTEM ADMINISTRATION menu
enables the System Administrator to perform a number of file system
management functions. They are:
·
Listing the number of images stored under each directory and
the percentage of total hard disk space consumed by each
account
·
Deleting all of the images scanned under any directory
86 ·Scanning to the Network (SCAN mode)
XEROX WIDE FORMAT COPY SYSTEM
·
Deleting all of the images currently stored on the hard disk.
Refer to "File System" in the "Main Menu" section of this manual for
complete information about the above functions.
XEROX WIDE FORMAT COPY SYSTEM
Scanning to the Network (SCAN mode) · 87
Main Menu
Main Menu
The Main Menu provides options for configuring the system, obtaining
system information, performing system administration functions, and
running system diagnostics.
When you access the Main Menu, a menu containing the following sub-
menus is displayed:
·
CONFIGURATION - Enables you to configure the settings for a
variety of system options. These include localization, the
Scanner Control Panel, copy options, scan options for Normal,
Line and Photo modes (and Color, if enabled), timers, the power
saver timeout, and Scanner control for Copy and Scan modes.
·
·
SYSTEM INFORMATION - Enables you to obtain information
about the system components, display the Scanner fault list,
print configuration pages, and view user account information.
SYSTEM ADMINISTRATION - Enables the system administrator
to perform job accounting, file system management, security,
and change password functions. Access to this menu requires
an administrator's password.
·
DIAGNOSTICS - Enables the Customer Service Engineer and/or
the operator to run a number of system diagnostic routines.
To access the Main Menu:
1. Press the Menu key.
READY TO COPY
INSERT DOCUMENT
AUTO
1
100.0%
Next
Mode
Menu
Previous
Enter
Exit
88 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
The MAIN MENU screen is displayed. The black arrows indicate that the
menu list contains more items than are visible. The selected option is
highlighted.
MAIN MENU
CONFIGURATION
SYSTEM INFORMATION
SYSTEM ADMINISTRATION
2. Press the Previous or Next key to scroll through the list options.
3. When the desired option is highlighted, press the Enter key to
select the option.
Configuration menu
The CONFIGURATION option of the Main Menu provides a sub-menu of
the following choices:
·
·
LOCALIZATION - Sets the display language and units of
measurements.
CONTROL PANEL - Controls whether the beeper is used for the
key click and invalid entry beeps. Also allows selection of the
font display style and the default operating mode.
·
·
COPY OPTIONS - Sets the choices for standard media series,
custom media formats, custom reduction/enlargement values,
and imaging parameters.
IMAGE ENHANCEMENTS - Enhances the appearance of a
color scanned images in particular color halftones, Scanning
speed BEST IQ and FASTEST, and Dynamic Background
Removal. The FASTEST selections requires the Turbo III
·
·
·
TIMERS - Sets the values for the Feature, Printer Interrupt, and
File Deletion timers.
POWER SAVER - Sets the number of hours of inactivity after
which the system goes into Power Saver mode.
SCANNER CONTROL - Sets the choices for the operation of the
Scanner for both copying and scan-to-file. Auto Scan, Document
Return, and Mode (Manual Width, Auto Width,
To access the CONFIGURATION menu:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed. The black arrows
indicate the menu contains more options than are visible. The
selected option is highlighted.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 89
CONFIGURATION
LOCALIZATION
CONTROL PANEL
COPY OPTIONS
3. Press the Previous or Next key to scroll through the list of
options.
4. When the desired option is highlighted, press the Enter key to
select the options. The menu or screen for the selected option is
displayed.
The LOCALIZATION option of the CONFIGURATION menu sets the
language in which messages are displayed. It also controls whether
measurements are displayed in English or metric units.
LOCALIZATION
To set the display language or units:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Enter key to select LOCALIZATION. The
LOCALIZATION screen is displayed. Below is an example of the
LOCALIZATION screen.
LOCALIZATION
LANGUAGE: ENGLISH
DISPLAY UNITS:
4. Press the Previous or Next key to highlight LANGUAGE or
DISPLAY UNITS.
5. Press the Enter key to select the highlighted option.
6. Press the Previous or Next key to highlight the desired setting
for the option.
The choices for LANGUAGE are ENGLISH, SPANISH, FRENCH,
ITALIAN, GERMAN, or PORTUGUESE. ENGLISH is the default setting.
The choices for DISPLAY UNITS are INCHES or MM (MILLIMETERS).
INCHES is the default setting.
7. Press the Enter key to select the highlighted setting.
8. Repeat steps 4 through 6 to change the remaining setting, if
desired.
9. Press the Exit key to return to the CONFIGURATION menu
screen.
90 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
The CONTROL PANEL option of the CONFIGURATION menu controls
whether the beeper is used for the key click and invalid entry beeps. It
also allows selection of the font display style and the default mode of
operation for the WIDE FORMAT COPY SYSTEM.
CONTROL PANEL
To set the beeper, text style or default operating mode:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key to select CONTROL PANEL.
4. Press the Enter key to select CONTROL PANEL. The
CONTROL PANEL screen is displayed. Below is an example of
the CONTROL PANEL screen.
CONTROL PANEL
BEEPER:
TEXT:
ENABLED
NORMAL
COPY
DEFAULT MODE:
5. Press the Previous or Next key to highlight BEEPER, TEXT
MODE or DEFAULT MODE.
6. Press the Enter key to select the highlighted option.
7. Press the Previous or Next key to highlight the desired setting
for the option.
The choices for BEEPER are ENABLED or DISABLED. ENABLED is
the default setting. The Initialization Beep and the Fault Beep are not
affected by this setting and cannot be turned off.
The choices for TEXT are NORMAL or BOLD. NORMAL is the default
setting.
The choices for DEFAULT MODE are COPY or SCAN. COPY is the
default setting.
NOTE: The DEFAULT MODE setting will not be displayed unless the
Scan To Net feature is enabled. SCAN mode is an option on the 8825
and 8850 Digital Solutions. To order this feature, contact XEROX
Representative.
8. Press the Enter key to select the highlighted setting.
9. Repeat steps 5 through 8 if you wish to change another setting.
10. Press the Exit key to return to the CONFIGURATION menu
screen.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 91
The COPY OPTIONS option of the CONFIGURATION menu provides a
sub-menu of the following choices:
COPY OPTIONS
·
MEDIA SERIES - Sets the standard media sizes for preset
output formats. Table 5 on the below shows the standard media
series and the sizes associated with them.
·
CUSTOM MEDIA FORMATS - Sets the custom media sizes for
preset output formats.
·
·
CUSTOM R/E PRESETS - Sets the reduction/enlargement ratios
IMAGING - Sets the imaging options.
To access the COPY OPTIONS menu:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until COPY OPTIONS is displayed. The
COPY OPTIONS menu screen is displayed. The black arrows
indicate that the menu contains more options than are visible.
The selected option is highlighted.
COPY OPTIONS
MEDIA SERIES
CUSTOM MEDIA FORMATS
CUSTOM R/E PRESETS
4. Press the Previous or Next key to scroll through the list of
options.
5. Press the Enter key to select the highlighted option. The screen
for the selected option is displayed.
92 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
Table 5. Media sizes
Choose Series
To Display
Sizes
Dimensions
(width x length)
ANSI
A
B
C
D
E
8.5 x 11 inches (215.9 x 279.4 mm)
11 x 17 inches (279.4 x 431.8 mm)
17 x 22 inches (431.8 x 558.8 mm)
22 x 34 inches (558.8 x 863.6 mm)
34 x 44 inches (836.6 x 1117.6 mm)
ARCH
A
9 x 12 inches (228.6 x 304.8 mm)
12 x 18 inches (304.8 x 457.2 mm)
18 x 24 inches (457.2 x 609.6 mm)
24 x 36 inches (609.6 x 914.4 mm)
36 x 48 inches (914.4 x 1219.2 mm)
30 x 42 Inches (76.2 x 106.7 mm)
B
C
D
E
30
ISO A (JIS A)
A4
A3
A2
A1
A0
210 x 297 mm
297 x 420 mm
420 x 594 mm
594 x 841 mm
841 x 1189 mm
ISO B (JIS B)
B4
B3
B2
B1
250 x 353 mm
353 x 500 mm
500 x 707 mm
707 x 1000 mm
The MEDIA SERIES option controls which standard media series are
displayed when Preset is selected from the Output Format portion of the
Scanner Control Panel.
MEDIA SERIES
You can select one or more media series to be displayed. Refer to Table
5 on the previous page for a listing of the sizes associated with each
media series.
To enable/disable a media series:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until COPY OPTIONS is highlighted.
4. Press the Enter key to select COPY OPTIONS. The COPY
OPTIONS menu screen is displayed.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 93
5. Press the Enter key to select MEDIA SERIES. The MEDIA
SERIES screen is displayed. Below is an example of the MEDIA
SERIES screen.
MEDIA SERES
ANSI
ARCH
ISO A
ISO B
JIS B
6. Press the Previous or Next key to highlight a media series.
7. Press the Enter key to ENABLE or DISABLE the highlighted
media series. A check mark appears in the box to the left of the
series when the series is enabled.
The factory default setting is ENABLED for the ANSI media series and
DISABLED for all others.
8. Repeat steps 6 and 7 for each media series you wish to enable
or disable.
9. Press the Exit key to return to the COPY OPTIONS menu
screen.
The CUSTOM MEDIA FORMATS option controls which custom media
formats are displayed when Preset is selected from the Output Format
portion of the Scanner Control Panel. You can specify up to six custom
media formats. To use the SCANNER CONTROL, MODE:
PRODUCTIVITY: CUSTOM mode the custom sizes must be entered in
the CUSTOM MEDIA FORMATS.
CUSTOM MEDIA
FORMATS
To specify a custom media format:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until COPY OPTIONS is highlighted.
4. Press the Enter key to select COPY OPTIONS. The COPY
OPTIONS menu screen is displayed.
5. Press the Next key to highlight CUSTOM MEDIA FORMATS.
6. Press the Enter key to select CUSTOM MEDIA FORMATS. The
CUSTOM MEDIA FORMATS screen is displayed.
The first "0.0" in each "0.0 x 0.0" format represents the width. The
second "0.0" represents the length.
NOTE: The formats are expressed in the units of measurement selected
for the machine. Refer to "Localization" in the "Main Menu" section for
further information.
94 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
Below is an example of the MEDIA SERIES screen. In the example, the
display units have been set to inches.
CUSTOM MEDIA FORMATS (IN)
0.0.X 0.0
0.0 X 0.0
0.0.X 0.0
0.0 X 0.0
0.0.X 0.0
0.0 X 0.0
7. Press the Previous or Next key to highlight the desired field.
8. Use the numeric keypad to enter the value for the highlighted
field.
9. Widths in excess of 36 inches (914 mm) or less than 11 inches
(297 mm) are not valid.
10. Press the Enter key to confirm the value.
11. Repeat steps 7 through 9 until all desired formats are defined.
NOTE: Any custom formats that are not defined are automatically set to
zero and are not displayed elsewhere.
12. Press the Exit key to return to the COPY OPTIONS menu
screen.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 95
The CUSTOM R/E PRESETS option controls which
CUSTOM R/E PRESETS
reduction/enlargement ratios are displayed when Preset is selected from
the Reduction/Enlargement portion of the Scanner Control Panel. You
can specify up to six reduction/enlargement presets.
To specify a reduction/enlargement preset:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until COPY OPTIONS is highlighted.
4. Press the Enter key to select COPY OPTIONS. The COPY
OPTIONS menu screen is displayed.
5. Press the Next key until CUSTOM R/E PRESETS is highlighted.
6. Press the Enter key to select CUSTOM R/E PRESETS. The
CUSTOM R/E PRESETS screen is displayed. Below is an
example of the CUSTOM R/E PRESETS screen.
CUSTOM R/E PRESETS
100.0%
100.0%
100.0%
100.0%
100.0%
100.0%
7. Press the Previous or Next key to highlight the value you wish
to change.
8. Use the numeric keypad to enter the desired value. The valid
value range is from 25 to 400%.
NOTE: Duplicate values are not displayed in the Preset
Reduction/Enlargement list. You can remove a preset value from the list
by setting the value to 100.0%.
9. Press the Enter key to confirm the value.
10. Repeat steps 7 through 9 for each value you wish to change.
11. Press the Exit key to return to the COPY OPTIONS menu
screen.
The IMAGING option allows you to perform the following functions:
IMAGING
·
Enable or disable automatic image rotation. If AUTO ROTATE is
enabled, the scanned image will be electronically rotated, if
necessary, to better fit the specified output format.
·
REDUCTION LINE PRESERVATION
To enable/disable the imaging options:
96 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until COPY OPTIONS is highlighted.
4. Press the Enter key to select COPY OPTIONS. The COPY
OPTIONS menu screen is displayed.
5. Press the Next key until IMAGING is highlighted.
6. Press the Enter key to select IMAGING. The IMAGING screen
is displayed. Below is an example of the IMAGING screen.
IMAGING
AUTO-ROTATE
4 REDUCTION LINE PRESERVATION
7. Press the Previous or Next key to highlight the desired option.
8. Press the Enter key to enable or disable the highlighted option.
A check mark appears in the box to the left of the option when
the option is enabled.
The factory default setting is disabled for AUTO-ROTATE.
9. Repeat steps 7 and 8 to enable or disable REDUCTION LINE
PRESERVATION, if desired.
10. Press the Exit key to return to the COPY OPTIONS menu
screen.
The IMAGE ENHANCEMENT feature settings are used to enhance the
appearance of color scanned images, particularly halftone color originals
( for example, maps).
IMAGE ENHANCEMENTS
This feature will greatly enhance the printing of a color sample using the
Color Scan to Print feature key.
To enable the IMAGE ENHANCEMENT features, perform the following:
1. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
2. Press the Next key until IMAGE ENHANCEMENT is highlighted.
3. Press the Enter key to select IMAGE ENHANCEMENT. The
IMAGE ENHANCEMENT menu screen is displayed.
4. Press the Next key to highlight COLOR IQ.
5. Press the Enter key to select COLOR IQ. The COLOR IQ screen
is displayed.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 97
IMAGE ENHANCEMENT
SRGB
COLOR IQ:
NORMAL MODE:
BEST IQ
4DYNAMIC BACKGROUND REMOVAL
6. Press the Next key to select the enhancement option you want:
·
·
NONE: scanned color has no color correction applied.
SRGB: scanned colors will be converted to the SRGB color
space
·
ADAPTIVE CONTRAST: scanned colors are first converted
to the SRGB color space, then enhanced using an adaptive
contrast algorithm. The adjustment changes the images
white point, black point,
NOTE: Further color halftone image enhancement can be achieved
when printing by enabling the Error Diffusion Raster Halftone Method in
the controller Web PMT. The setting is found on the Processing Defaults
page. Select Error Diffusion from the Raster Halftone Method pull-down
menu.
7. Press the Enter key the select the enhancement setting.
8. Press the Next key to select NORMAL MODE then press the
Enter key to select Normal Mode.
9. Press the Previous of Next to scroll through the settings BEST
IQ and FASTEST then press the Enter key to select the setting.
BEST IQ is the default
10. Press the Next key to select DYNAMIC BACKGROUND
SUPPRESSION. Then press the Enter key to enable/disable
DYNAMIC BACKGROUND REMOVAL. Disabling the DYNAMIC
BACKGROUND REMOVAL enables the STATIC
BACKGROUND REMOVAL. DYNAMIC BACKGROUND
REMOVAL is the default and should be used for most document
types
11. Press the Enter key to confirm the selection.
12. Press the Exit key to return to the CONFIGURATION menu.
The TIMERS option of the CONFIGURATION menu allows you to set the
values for the time-out functions. Pressing any key or scanning a
document resets the timers.
TIMERS
The timers are as follows:
·
FEATURE - Controls how long the current feature parameters
remain in effect after the last key press, scan completion, or
insertion of a document into the Scanner. The FEATURE timer
can be set between 0 and 99 minutes. The factory default is 5
minutes. A value of 0 means that the feature will never time out.
98 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
NOTE: To prevent images from being lost, feature time-outs will not
occur during the sets build process.
·
PRINTER INTERRUPT - Controls how long the Printer remains
in the interrupted state with no interruption at the Scanner
Control Panel. This timer pertains to print jobs that have been
interrupted to allow a copy job to process. The allowed range is
1 to 99 minutes. The factory default is 1 minute.
·
FILE DELETION - Specifies the maximum amount of time a
scanned image file remains on the file system before being
deleted. This timer pertains only to files scanned when the
WIDE FORMAT COPY SYSTEM is in the READY TO SCAN
mode. This timer can be set between 1 and 24 hours in
increments of 1 hour. When a file is scanned in, it is given a time
stamp. When the age of the file on the hard disk exceeds the
value of the FILE DELETION timer, the file is automatically
deleted to allow space for new files. The default value is 24
hours. After the files have been deleted, the directory will also be
deleted if no other files are scanned to it.
To adjust a timer:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until TIMERS is highlighted.
4. Press the Enter key to select TIMERS. The TIMERS screen is
displayed.
TIMERS
FEATURE (0 — 99) MIN
60
PRINTER INTERRUPT (1 — 99 MIN): 1
FILE DELETION (1-24 HR): 24
5. Press the Previous or Next key to highlight the desired timer.
6. Press the Enter key to select the highlighted timer.
7. Use the numeric keypad to enter the timer value.
8. Press the Enter key to confirm the value.
9. Repeat steps 5 through 8 if you want to set the value for
additional timers.
10. Press the Exit key to return to the CONFIGURATION menu
screen.
The POWER SAVER option of the CONFIGURATION menu allows you
to set the number of hours of inactivity after which the system goes into
Power Saver mode.
POWER SAVER
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 99
To adjust the power saver:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until POWER SAVER is highlighted.
4. Press the Enter key to select POWER SAVER. The POWER
SAVER screen is displayed.
POWER SAVER
POWER SAVER DELAY (0 4 HR): 3
-
5. Use the numeric keypad to enter the power saver value. The
valid value range is 0 to 4 hours. The factory default is 3 hours.
6. Press the Enter key to confirm the value.
7. Press the Exit key to return to the CONFIGURATION menu
screen.
The SCANNER CONTROL option of the CONFIGURATION menu allows
you to set the options for how the Scanner starts and finishes a scan. It
contains the following features:
SCANNER CONTROL
·
AUTOSCAN - Tells the Scanner either to start the scan
automatically when the document is inserted (ENABLED), or to
wait until the Start key is pressed (DISABLED). ENABLED is
the factory default setting.
·
DOCUMENT RETURN - Tells the Scanner, after the scan, either
to return the document to the front of the Scanner (FRONT), or
to drop the document from the rear of the Scanner into the catch
tray (REAR). REAR is the factory default setting.
NOTE: Refer to Controlling the Scan for additional information.
·
MODE:
·
·
·
MANUAL WIDTH - The user must enter the document width
and very carefully center the document. In this mode the
document will be prescanned.
AUTOWIDTH - Enables the automatic detection of the width
of the document. . In this mode the document will be
prescanned.
AUTOWIDTH/AUTOCENTER - Enables the automatic
centering of the image and automatic width detection. This
selection is the default. . In this mode the document will be
prescanned.
·
PRODUCTIVITY:. This feature does not use AUTOCENTER
requiring the operator to manually align the document within
100 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
the media guidelines on the Feed-in Tray. The width sensors
eliminate the need for a prescan thereby increasing the
overall throughput of the system resulting in higher
productivity. When this feature is used the operator must
select the media series, ANSI, ARCH, ISO A, ISO B JIS B
and CUSTOM etc since the number of sensors provided can
not monitor every media type.
To use the MODE: PRODUCTIVITY: CUSTOM the custom
sizes must be entered in the CUSTOM MEDIA FORMATS
(Menu, CONFIGURATION>COPY OPTIONS).
To set the Scanner Control features:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Enter key to select CONFIGURATION. The
CONFIGURATION menu screen is displayed.
3. Press the Next key until SCANNER CONTROL is highlighted.
4. Press the Enter key to select SCANNER CONTROL. The
SCANNER CONTROL screen is displayed.
SCANNER CONTROL
AUTOSCAN
4
FRONT
DOCUMENT RETURN:
MODE:
PRODUCTIVITY — ANSI
5. Press the Previous or Next key to select the desired feature.
6. Press the Enter key to confirm the choice.
7. Press the Previous or Next key to select the desired setting.
For AUTOSCAN, , you can enable or disable the feature. A check mark
in the box to the left of the feature indicates that the feature is enabled.
Enabled is the factory default setting for these features.
For DOCUMENT RETURN, the selections are FRONT and REAR.
FRONT is the factory default setting.
For MODE: use the Previousor Next keys to select the desired option
then press the Enter key to confirm the choice.. The options are
MANUAL, AUTOWIDTH, AUTOWIDTH/AUTOCENTER, or
PRODUCTIVITY. If PRODUCTIVITY is selected, then use the Previous
or Next key too select the ANSI, ARCH, ISO A, ISO B, JISB, or
CUSTOM setting.
Use the CUSTOM setting when documents of mixed series will be
scanned in the same job. The CUSTOM selection can only be used
when sizes are entered in the CUSTOM MEDIA SIZES (Menu
CONFIGURATION>COPY OPTIONS.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 101
CUSTOM MEDIA FORMATS (IN)
0.0.X 0.0
0.0.X 0.0
0.0 X 0.0
0.0 X 0.0
0.0 X 0.0
0.0.X 0.0
8. Press the Exit key to return to the CONFIGURATION menu
screen.
102 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
System Information menu
The SYSTEM INFORMATION option of the MAIN MENU contains the
following menu choices:
·
·
·
SYSTEM DESCRIPTION - Provides information about each
component connected to the WIDE FORMAT COPY SYSTEM.
RECENT FAULT LIST - Displays the most recent faults related
to the Scanner.
CONFIGURATION PRINTS - Prints Copier and Printer
configuration pages.
To access the SYSTEM INFORMATION menu:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key to highlight SYSTEM INFORMATION.
3. Press the Enter key to select SYSTEM INFORMATION. The
SYSTEM INFORMATION menu screen is displayed. The black
arrows indicate that the menu contains more options than are
visible. The selected option is highlighted.
SYSTEM INFORMATION
SYSTEM DESCRIPTION
RECENT FAULT LIST
CONFIGURATION
4. Press the Previous or Next key to scroll through the list of
options.
5. When the desired option is highlighted, press the Enter key to
select the option. The menu or screen for the selected option is
displayed.
The SYSTEM DESCRIPTION option of the SYSTEM INFORMATION
menu provides information on the model identity and firmware version for
each component connected to the WIDE FORMAT COPY SYSTEM.
SYSTEM DESCRIPTION
To display component information:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key to highlight the SYSTEM INFORMATION
option.
3. Press the Enter key to select SYSTEM INFORMATION. The
SYSTEM INFORMATION menu screen is displayed.
4. Press the Enter key to select SYSTEM DESCRIPTION. The
SYSTEM DESCRIPTION screen is displayed.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 103
SYSTEM DESCRIPTION
SCANNER
CONTROLLER
CONTROL PANEL
5. Press the Previous or Next key to highlight the component
about which you want to view information.
6. Press the Enter key to select the highlighted component. The
screen for the selected component is displayed. Following are
examples of the screens for each of the components.
SCANNER
MODEL: XEROX WIDE FORMAT SCAN SYSTEM
FIRMWARE: 3.2.5
CONTROLLER
MODEL: 4
FIRMWARE: 10.0
RAM: 512MB
NOTE: The CONTROLLER screen also provides the amount of Random
Access Memory (RAM).
CONTROL PANEL
MODEL: 1
FIRMWARE: 1.1.0
PRINTER
MODEL: WIDE FORMAT XXXX
FIRMWARE: XXX
'
104 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
NOTE: The XXXX represents the Printer name 721
FINISHER
MODEL:
NOTE: This screen identifies the Finisher, if any. If there is no finisher,
the MODEL is displayed as NONE. If a Folder is connected, the
FINISHER screen displays the configuration of the connected Folder.
7. Press the Exit key to return to the SYSTEM DESCRIPTION
screen.
The RECENT FAULT LIST option of the SYSTEM INFORMATION menu
displays the most recent faults related to the Scanner. Fault messages
are stored in the Controller. Each fault message contains a fault code
and a digital time stamp. When you call for service, the service center
may ask you for this information.
RECENT FAULT LIST
To display the recent fault list:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key to highlight SYSTEM INFORMATION.
3. Press the Enter key to select SYSTEM INFORMATION. The
SYSTEM INFORMATION menu screen is displayed.
4. Press the Next key to highlight RECENT FAULT LIST.
5. Press the Enter key to select RECENT FAULT LIST. The
RECENT FAULT LIST screen is displayed. Below is an example
of the RECENT FAULT LIST screen.
RECENT FAULT LIST
37449914 50000008
37449868 50000008
6. Press the Previous or Next key to scroll through the list.
7. Press the Exit key to return to the SYSTEM INFORMATION
menu screen.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 105
The CONFIGURATION PRINTS option of the SYSTEM INFORMATION
menu allows you to print one of the following selections:
CONFIGURATION PRINTS
·
·
·
·
Copier Configuration
Printer Configuration
Printer Settings
All of the above.
To print a configuration print:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key to highlight SYSTEM INFORMATION.
3. Press the Enter key to select SYSTEM INFORMATION. The
SYSTEM INFORMATION menu screen is displayed.
4. Press the Previous or Next key until CONFIGURATION
PRINTS is highlighted.
5. Press the Enter key to select CONFIGURATION PRINTS. The
CONFIGURATION PRINTS screen is displayed.
CONFIGURATION
COPIER CONFIGURATION
PRINTER CONFIGURATION
PRINTER SETTINGS
ALL CONFIGURATION PRINTS
6. Press the Previous or Next key to highlight the configuration
page you want to print.
7. Press the Enter key to select the highlighted configuration. The
screen for the selected configuration is displayed. The default
response is YES.
Below is an illustration of the COPIER CONFIGURATION screen.
COPIER CONFIGURATION
QUEUE TO PRINTER:
YES
8. Press the Enter key to confirm the response. A status message
is displayed indicating that the configuration has been queued to
the Printer.
Below are illustration of the other CONFIGURATION PRINT screen with
the status message.
106 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
PRINTER CONFIGURATION
QUEUE TO PRINTER:
YES
PRINTER SETTINGS
QUEUE TO PRINTER:
YES
ALL CONFIGURATION PRINTS
QUEUE TO PRINTER:
YES
9. Press the Exit key to return to the CONFIGURATION PRINTS
screen.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 107
System Administration menu
The SYSTEM ADMINISTRATION option of the MAIN MENU is reserved
for the system administrator. It can be accessed only after entering the
system administration password.
When this option is selected, the system administrator is immediately
prompted for a password. See "Entering the system administration
password" in this section for complete information about the password
entry.
Once the system administration password has been entered correctly,
the SYSTEM ADMINISTRATION menu screen is displayed. It contains
the following options:
·
JOB ACCOUNTING MODE - Allows the system administrator
enable the Job Accounting Mode. The options are DISABLED,
ENABLED, and OPTIONAL. The default is DISABLED.
·
·
·
FILE SYSTEM - Allows the system administrator to view and
delete account information.
CHANGE PASSWORD - Allows the system administrator to
change the system administration password
SECURITY SETTINGS - Allows the system administrator to set
the image recall feature.
Access to the SYSTEM ADMINISTRATION menu requires the entry of
the system administration password.
Entering the system
administration
password
To enter the system administration password:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Previous or Next key until SYSTEM
ADMINISTRATION is highlighted.
3. Press the Enter key to select SYSTEM ADMINISTRATION. The
SYSTEM ADMINISTRATION password screen is displayed.
SYSTEM ADMINISTRATION
ENTER PASSWORD:
4. Use the numeric keypad to enter the password. The password
will display as asterisks.
5. Press the Enter key to confirm the password entry. The
SYSTEM ADMINISTRATION menu screen is displayed. The
black arrows indicate the menu contains more options than are
visible. The selected option is highlighted.
108 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
SYSTEM
JOB ACCOUNTING MODE
FILE SYSTEM
CHANGE PASSWORD
SECURITY
NOTE: If an incorrect password is entered, an error message will be
displayed as shown below. Enter the password again.
SYSTEM ADMINISTRATION
PASSWORD: *****
INVALID PASSWORD, RE-ENTER
6. Press the Previous or Next key to scroll through the list of
system administration options.
7. Press the Enter key to select the desired option.
The JOB ACCOUNTING option of the System Administration menu
allows the system administrator with access to enable Job Accounting.
The options are DISABLED, ENABLED, and OPTIONAL. The default is
DISABLED.
JOB ACCOUNTING
FILE SYSTEM
NOTE: This option will not be displayed unless the Scan to Net feature
is enabled. SCAN mode is an option on the WIDE FORMAT COPY
SYSTEM 8825 and 8850. If SCAN mode has not been enabled, the
FILE SYSTEM information is not available. To order this feature, contact
your XEROX representative.
The FILE SYSTEM option of the SYSTEM ADMINISTRATION menu
provides a sub-menu of the following menu choices:
·
LIST BY DIRECTORY- Allows the system administrator to list
the number of images stored under each directory and the
percentage of total hard disk space consumed by the directory.
·
·
DELETE IMAGES - Allows the system administrator to delete all
of the images scanned for a particular directory.
DELETE ALL IMAGES - Allows the system administrator to
delete all of the images currently stored on the hard disk.
To access the FILE SYSTEM menu:
1. Access the SYSTEM ADMINISTRATION menu. See "Entering
the system administration password" in this section.
2. Press the Next key to highlight FILE SYSTEM.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 109
3. Press the Enter key to select FILE SYSTEM. The FILE
SYSTEM menu screen is displayed.
FILE SYSTEM
LIST BY DIRECTORY
DELETE IMAGES
DELETE ALL IMAGES
4. Press the Previous or Next key to highlight the desired option.
5. Press the Enter key to select the highlighted option.
The LIST BY DIRECTORY option allows the system administrator to
display a list of the number of images stored under each directory and
the percentage of total hard disk space consumed by each account.
LISTING STORED
IMAGE INFORMATION
BY DIRECTORY
To list scanned image information by account:
1. Access the SYSTEM ADMINISTRATION menu. See "Entering
the system administration password" in this section.
2. Press the Next key to highlight FILE SYSTEM.
3. Press the Enter key to select FILE SYSTEM. The FILE
SYSTEM menu screen is displayed.
4. Press the Enter key to select LIST BY DIRECTORY. The LIST
BY DIRECTORY screen is displayed. The following illustration is
an DIRECTORY example of the LIST BY screen.
NOTE: Directories that do not contain files will not be displayed.
Directories not containing files are deleted.
LIST BY DIRECTORY
SIZE (%)
COUNT
2*
DIRECTORY
<1
2
images
images
35
For each directory, the account name( DIRECTORY), the number of
images stored under the directory(COUNT), and the percentage of total
disk space consumed by the account (SIZE (%)) are shown. The length
of the directory name may cause the information associated with the
directory to wrap to the next line. Also, if the directory name exceeds the
character limit of the first line, the name will be truncated at the width of
the screen.
Use the Previousor Next key to scroll through the list.
An asterisk in the COUNT field indicates that some images in memory
have not yet been processed. A "<1" in the SIZE field indicates the
account uses less than 1% of the total disk space on the file system.
110 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
5. Press the Exit key to return to the FILE SYSTEM menu screen.
The DELETE IMAGE option allows the system administrator to delete all
the images stored for a particular account.
DELETING STORED
IMAGES BY
DIRECTORY
To delete stored images by account:
1. Access the SYSTEM ADMINISTRATION menu. See "Entering
the system administration password" in this section.
2. Press the Next key to highlight FILE SYSTEM.
3. Press the Enter key to select FILE SYSTEM. The FILE
SYSTEM menu screen is displayed.
4. Press the Next key to highlight DELETE IMAGES.
5. Press the Enter key to select DELETE IMAGES. The DELETE
IMAGES screen is displayed.
DELETE IMAGES
DIRECTORY:
Images o
6. Use the numeric keypad to enter the name of the directory from
which you would like delete the stored images.
7. Press the Enter key to confirm the account number. A delete
confirmation screen is displayed. The default response is NO.
The following illustration is an example of the DELETE IMAGES screen.
DELETE IMAGES
DIRECTORY:
Images
NO
ARE YOU SURE ?
8. Press the Previous or Next key to change the response to YES.
9. Press the Enter key to confirm the deletion. While the deletion is
in process, a "DELETING. . ." message is displayed. When the
deletion is complete, the status changes to IMAGES DELETED.
Below is an example of the deletion screen.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 111
DELETE IMAGES
DIRECTORY:
Images o
IMAGES DELETED
10. Press the Exit key to return to the FILE SYSTEM menu screen.
The DELETE ALL IMAGES option allows the system administrator to
delete all the images stored on the file system.
DELETING ALL
STORED IMAGES
To delete all stored images:
1. Access the SYSTEM ADMINISTRATION menu. See "Entering
the system administration password" in this section.
2. Press the Next key to highlight FILE SYSTEM.
3. Press the Enter key to select FILE SYSTEM. The FILE
SYSTEM menu screen is displayed.
4. Press the Next key until DELETE ALL IMAGES is highlighted.
5. Press the Enter key to select DELETE ALL IMAGES. The
DELETE ALL IMAGES screen is displayed. The default
response is NO.
DELETE ALL IMAGES
ARE YOU SURE?:
NO
6. Press the Previous or Next key to change the response to YES.
7. Press the Enter key to confirm the deletion. While the deletion is
in process, a "DELETING. . ." message is displayed. When the
deletion is complete, the status changes to IMAGES DELETED.
DELETE IMAGES
ARE YOU SURE?:
YES
IMAGES DELETED
8. Press the Exit key to return to the FILE SYSTEM menu screen.
112 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
The CHANGE PASSWORD option of the SYSTEM ADMINISTRATION
menu allows the system administrator to change the system
administration password.
CHANGE PASSWORD
The default system administration password on all newly delivered
machines, is 0 (zero). The system administrator is required to change the
password after the initial log in. Immediately following the log in, the
CHANGE PASSWORD screen is displayed. The password must be
changed at that time.
If the existing password has been lost, call for service. The customer
service engineer will reset the password to the default value of 0. The
system administrator should then change the password to a different
value.
NOTE: Changing the system administrator password on the Scanner
Control Panel also changes the system administrator password for the
Printer. These two passwords always have the same value.
To change the system administration password:
1. Access the SYSTEM ADMINISTRATION menu. See "Entering
the system administration password" in this section.
2. Press the Next key until CHANGE PASSWORD is highlighted.
3. Press the Enter key to select CHANGE PASSWORD. The
CHANGE PASSWORD screen is displayed.
CHANGE PASSWORD
ENTER OLD PASSWORD:
4. Use the numeric keypad to enter the old password.
5. Press the Enter key to confirm the old password. The CHANGE
PASSWORD screen will instruct you to enter the new password.
CHANGE PASSWORD
ENTER NEW PASSWORD:
6. Use the numeric keypad to enter the new password. The
password will display as asterisks.
NOTE: The valid range for passwords is 0 - 65535. If the existing
password or an invalid password is entered, an error message will be
displayed. The new password must be entered again.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 113
7. Press the Enter key to confirm the new password. The
CHANGE PASSWORD screen will instruct you to re-enter the
new password.
CHANGE PASSWORD
RE-ENTER NEW PASSWORD:
8. Use the numeric keypad to re-enter the new password. The
password will display as asterisks.
9. Press the Enter key to confirm the re-entry. You will be returned
to the SYSTEM ADMINISTRATION menu screen. The new
password is now effective. The old password is no longer valid.
At most installations, users have the ability to recall the last image
scanned and all the settings associated with that image. The recalled
image can then be printed without the need to scan from the original
document.
SECURITY SETTINGS
Security concerns at certain installations, however, might require that the
image recall feature be disabled. The SECURITY SETTINGS option of
the System Administration menu allows the system administrator to
enable or disable the image recall feature. The default setting is
ENABLED.
To enable/disable the image recall feature:
1. Access the SYSTEM ADMINISTRATION menu.
2. Press the Next key until SECURITY SETTINGS is highlighted.
3. Press the Enter key to select SECURITY SETTINGS. The
SECURITY SETTINGS screen is displayed.
SECURITY SETTINGS
IMAGE RECALL:
ENABLED
4. Press the Previous or Next key to highlight the desired
response, ENABLED or DISABLED.
5. Press the Enter key to confirm your selection.
6. Press the Exit key to return to the SYSTEM ADMINISTRATION
menu screen.
114 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
Diagnostics menu
The DIAGNOSTICS option of the Main Menu contains the following
menu choices:
·
·
USAGE METERS - Enables you to view usage information for
documents scanned and media printed.
CLEAR SCANNER USAGE - Enables the Customer Service
Engineer to reset to zero the usage value for documents
scanned. The diagnostic password is required for this function.
·
SCANNER DIAGNOSTICS - Provides a sub-menu of Scanner
diagnostic routines. Some of these routines are accessible by
both the operator and the Customer Service Engineer, but
should only be accessed by and operator when directed to do so
by Service. Access to these tests has been given to enable
some preliminary diagnostics to be done by phone before a
Customer Service Engineer is dispatched. Others are accessible
by the Service Engineer only and require the entry of the
diagnostic password.
·
·
INSTALLATION TEST PRINT - Enables the Customer Service
Engineer to make a copy of the test print to assist in diagnosing
the scanner.
PASSWORD - Enables the Customer Service Engineer to enter
the password for access to password-protected diagnostic
functions.
To access the DIAGNOSTICS menu:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed. The black arrows
indicate the menu contains more options than are visible. The
selected option is highlighted.
DIAGNOSTICS
USAGE METERS
CLEAR SCANNER USAGE
SCANNER DIAGNOSTICS
4. Press the Previous or Next key to scroll through the list of
options
5. When the desired option is highlighted, press the Enter key to
select the option. The menu or screen for the selected option is
displayed.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 115
Select the USAGE METERS option of the DIAGNOSTICS menu to view
the total system usage for documents scanned and media printed.
USAGE METERS
To view area and media usage:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Enter key to select USAGE METERS. The USAGE
METERS screen is displayed.
The USAGE METERS screen provides Scanner area usage and media
usage. Scanner area usage is measured in square units. Media usage
is measured in both linear and square units. Units are displayed as
either feet or meters depending on the display units selected for the
Scanner. Refer to "Localization" in the "Main Menu" section for complete
information about setting the display units.
Below is an example of the USAGE METERS screen. In the example,
the units are displayed as meters.
USAGE METERS
SCANNER (F2):
MEDIA LINEAR
MEDIA AREA
11
307
670
5. When finished viewing the usage information, press the Exit key
to return to the DIAGNOSTICS menu screen.
The CLEAR SCANNER USAGE option of the DIAGNOSTICS menu is
for use by the Customer Service Engineer only. It requires the entry of
the diagnostic password. It allows the Customer Service Engineer to
reset to zero the usage value for documents scanned.
CLEAR SCANNER
USAGE
If you select this option, the CLEAR SCANNER USAGE screen is
displayed. You cannot perform any functions in this screen. Press the
Exit key to return to the DIAGNOSTICS menu screen.
Below is an example of the USAGE METERS screen. In the example,
the units are displayed as square feet.
CLEAR SCANNER USAGE
:
SCANNER (F2)
1234
NO
ARE YOU SURE?:
116 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
The SCANNER DIAGNOSTICS option of the DIAGNOSTICS menu
provides a sub-menu of the following choices:
SCANNER
DIAGNOSTICS
·
·
·
·
IMAGE PATH - Enables you to validate the operation of the
image processing (IP) card and the image bar.
SCAN BAR - Enables you to calibrate the response of the scan
bar.
FULL SYSTEM TEST - Enables you to run all applicable tests on
the Scanner to determine if it is working properly.
WRITE NVR - Enables the Customer Service Engineer to modify
the contents of the non-volatile memory of the Scanner. The
diagnostic password is required for this function.
·
RESET NVR DEFAULTS - Enables the Customer Service
Engineer to reset the NVR values to the factory default values.
The diagnostic password is required for this function.
·
·
·
·
SCANNER RELIABILITY METER - Enables you to gather data
about the usage of the scanning mechanism.
SCANNER FAULTS (ORDERED) - Enables you to view the
entries in the internal Scanner Fault Log.
SCANNER FAULTS (COUNTS) - Enables you to view the last
cleared faults.
CLEAR SCANNER FAULT LOG - Enables the Customer Service
Engineer to erase the contents of the Scanner Fault Log. The
diagnostic password is required for this function.
·
·
CLEAN CALIBRATION ZONE - Enable you to quickly move the
calibration surface to the cleaning position.
COMPONENT TESTS - Provides a sub-menu of Scanner
component diagnostic routines. Some of these routines are
accessible by both the operator and the Customer Service
Engineer. Others are accessible by the Customer Service
Engineer only and require the entry of the diagnostic password.
·
READ NVR - Enables you to examine the contents of the non-
volatile RAM (NVR).
To access the SCANNER DIAGNOSTICS menu:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is
highlighted.
5. Press the Enter key to highlight SCANNER DIAGNOSTICS.
The SCANNER DIAGNOSTICS menu screen is displayed. The
black arrows indicate that the menu contains more options than
are visible. The selected option is highlighted.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 117
SCANNER DIAGNOSTICS
IMAGE PATH
SCAN BAR
FULL SYSTEM
6. Press the Previous or Next key to scroll through the list of
options.
7. When the desired option is highlighted, press the Enter key to
select the option. The menu or screen for the selected option is
displayed.
Select the IMAGE PATH option to validate the operation of the image
processing (IP) card and the image bar.
IMAGE PATH
To run the IMAGE PATH diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Enter key to select IMAGE PATH. The IMAGE PATH
screen is displayed.
IMAGE PATH
STATUS: 0
BAR2: 0
ALL: 0
BOARD ID: 2
BAR1: 0
BAR3: 0
When you enter the IMAGE PATH screen, the status field for all tests
contains a "0." After a few seconds, the results of the tests are
displayed. A test result with no failure displays as PASS. A test result
with a failure displays a failure code. If a failure code is displayed, call
for service.
7. Press the Exit key to return to the SCANNER DIAGNOSTICS
menu screen.
118 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
Select the SCAN BAR option to calibrate the response of the scan bar.
To run the SCAN BAR diagnostic:
SCAN BAR
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key to highlight SCAN BAR.
7. Press the Enter key to select SCAN BAR. The SCAN BAR
screen is displayed.
SCAN BAR
CALIBRATION TEST
PRESS START TO BEGIN
8. Press the Start key to begin the test. While the test is executing,
the bottom display line changes to "RUNNING."
At the completion of the test, the test result is displayed. A test result
with no failure displays as PASSED. A test result with a failure displays
as FAILED followed by ERROR CODE: and a hexadecimal value
between 0 and FF. If a failure code is displayed, call for service.
9. Press the Exit key to return to the SCANNER DIAGNOSTICS
menu screen.
Select the FULL SYSTEM TEST option to run all applicable tests on the
Scanner to determine if it is working properly.
FULL SYSTEM TEST
To run the FULL SYSTEM TEST diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until FULL SYSTEM TEST is highlighted.
7. Press the Enter key to select FULL SYSTEM TEST. The FULL
SYSTEM TEST screen is displayed.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 119
FULL SYSTEM TEST
F)
A)
B)
H)
C)
I)
D)
E)
G)
PRESS START TO BEGIN
Nine sub-tests are included in the system test. Each letter on the screen
corresponds to a sub-test as follows:
a) Post Test 5 - NVM (Non Volatile Memory) Verification
b) Post Test 6 - Motor Communications
c) Post Test 7 - SCVM Code Checksum
d) Post Test 8 - SCVM (Scanner Virtual Memory) Load and Functional
Test
e) Post Test 9 - Pixel Magic Interface
f) Post Test A - Pixel Magic Internal
g) Post Test B - Video Path
h) Post Test C - 24 VDC (Volts Direct Current) Power Supply Test
i) Post Test D - Lamp
8. Press the Start key to begin the system test. While the tests are
executing, the bottom display line changes to "RUNNING."
At the completion of the tests, the test results are displayed. If a sub-test
is successful, a "P" is displayed. If a sub-test fails, an "F" is displayed. If
an "F" is displayed the test has failed and service is required.
9. Press the Exit key to return to the SCANNER DIAGNOSTICS
menu screen.
The WRITE NVR option is for use by the Customer Service Engineer
only and requires the entry of the diagnostic password. It allows the
Customer Service Engineer to modify the contents of the non-volatile
memory of the Scanner.
WRITE NVR
If you select this option, the WRITE NVR screen is displayed. You
cannot perform any functions in this screen. Press the Exit key to return
to the SCANNER DIAGNOSTICS menu screen.
Below is an example of the WRITE NVR screen.
WRITE NVR
SIZE:
4
ADDRESS:
EXECUTE:
D0
NO
ABCD4321
DATA:
USE . KEY FOR HEX DIGITS
120 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
The RESET NVR DEFAULTS option is for use by the Customer Service
Engineer only and requires the entry of the diagnostic password. It
allows the Customer Service Engineer to reset the NVR values to the
factory default values.
RESET NVR DEFAULTS
If you select this option, the RESET NVR DEFAULTS screen is
displayed. You cannot perform any functions in this screen. Press the
Exit key to return to the SCANNER DIAGNOSTICS menu screen.
Below is an illustration of the RESET NVR DEFAULTS screen.
RESET NVR DEFAULTS
WARNING: THIS FUNCTION
DESTROYS NVR CONTENTS
EXECUTE:
NO
Select the SCANNER RELIABILITY METER option to view the current
value of the usage meter maintained by the Scanner. The meter counts
and displays the number of linear feet since the Scanner Fault Log was
last cleared. The number of linear feet between fault occurrences is an
indication of the reliability of the Scanner.
SCANNER RELIABILITY
METER
To run the SCANNER RELIABILITY METER diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until SCANNER RELIABILITY METER is
highlighted.
7. Press the Enter key to select SCANNER RELIABILITY METER.
The SCANNER RELIABILITY METER screen is displayed.
The Scanner usage meter is intended for gathering data about the
reliability of the scanning mechanism. This meter measures linear usage
only. Units are displayed as either feet or meters depending on the
display units selected for the machine. Refer to "Localization" in the
"Main Menu" section for complete information about setting the display
units.
Below is an example of the SCANNER RELIABILITY METER screen. In
the example, the units are displayed as feet.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 121
SCANNER RELIABILITY
LINEAR SCAN (FT):
COLOR (FT):
5678
0
8. Press the Exit key to return to the SCANNER DIAGNOSTICS
menu screen.
Select the SCANNER FAULTS (ORDERED) option to view the entries in
the internal Scanner Fault Log.
SCANNER FAULTS
(ORDERED)
To run the SCANNER FAULTS (ORDERED) diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until SCANNER FAULTS (ORDERED) is
highlighted.
7. Press the Enter key to select SCANNER FAULTS (ORDERED).
The SCANNER FAULTS (ORDERED) screen is displayed.
The first line of the display contains the value of the internal Scanner
Reliability Meter reading when the log was last cleared. If the log has
never been cleared, the value is set to zero. This line scrolls with the log
data.
The second and third lines contain the log entry information in columnar
format. The first column indicates the log entry number. The second
column indicates the fault code recorded in the log. The third column is
the value of the internal Scanner Usage Meter at the time the fault was
detected.
Below is an example of the SCANNER FAULTS (ORDERED) screen.
SCANNER FAULTS (ORDERED)
LAST CLEARED:
2001
2476
2402
01
02
01-02
01-03
8. Use the Previousor Next key to scroll through the listing.
122 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
The entries are presented three to a screen. You can view all valid
entries in the Scanner Fault Log from this screen. Empty log entries are
not displayed.
9. When finished viewing the fault data, press the Exit key to return
to the SCANNER DIAGNOSTICS menu screen.
Select the SCANNER FAULTS (COUNT) option to view the last cleared
faults.
SCANNER FAULTS
(COUNT)
To run the SCANNER FAULTS (COUNTS) diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until SCANNER FAULTS (COUNTS) is
highlighted.
7. Press the Enter key to select SCANNER FAULTS (COUNTS).
The SCANNER FAULTS (COUNTS) screen is displayed.
The first line of the display contains the value of the internal Scanner
Reliability Meter reading when the log was last cleared. If the log has
never been cleared, the value is set to zero. This line scrolls with the log
data.
The second and third lines contain the log entry information in columnar
format. The first column indicates the log entry number. The second
column indicates the fault code recorded in the log. The third column is
the value of the internal Scanner Usage Meter at the time the fault was
detected.
Below is an example of the SCANNER FAULTS (COUNTS) screen.
SCANNER FAULTS (COUNTS)
LAST CLEARED:
2001
2476
2402
01
02
01-02
01-03
8. Use the Previousor Next key to scroll through the listing.
The entries are presented three to a screen. You can view all valid
entries in the Scanner Fault Log from this screen. Empty log entries are
not displayed.
9. When finished viewing the fault data, press the Exit key to return
to the SCANNER DIAGNOSTICS menu screen.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 123
The CLEAR SCANNER FAULT LOG option is for use by the Customer
Service Engineer only and requires the entry of the diagnostic password.
It allows the Customer Service Engineer to erase the contents of the
Scanner Fault Log.
CLEAR SCANNER
FAULT LOG
If you select this option, the CLEAR SCANNER FAULT LOG screen is
displayed. You cannot perform any functions in this screen. Press the
Exit key to return to the SCANNER DIAGNOSTICS menu screen.
Below is an illustration of the CLEAR SCANNER FAULT LOG screen.
CLEAR SCANNER FAULT LOG
WARNING: THIS FUNCTION
DESTROYS ALL LOG MESSAGES
EXECUTE:
NO
The CLEAR CAL ZONE (Clear Calibration Zone) provides the user with
a quick way to move the Calibration Motor to the cleaning position. There
are two selections CLEANING POSITION AND HOME POSITION.
CLEAN CAL ZONE
CLEAN CAL ZONE
POSITION:
CLEANING POSITION
The COMPONENT TESTS option of the SCANNER DIAGNOSTICS
menu provides a sub-menu of the following menu choices:
COMPONENT TESTS
·
MOTOR SPEED - Enables the Customer Service Engineer to
adjust the Scanner motor speed and correct magnification errors
in the process direction. The diagnostic password is required for
this function.
·
·
·
LEAD EDGE/TRAIL EDGE - Enables you to execute the lead
edge/trail edge diagnostic.
SENSORS - Enables you to display the current state of the
Scanner optical paper sensors and the thick document sensor.
MOTOR COMMUNICATIONS - Enables a document motor
communications loopback test to assist in diagnosing a scanner
problem.
·
DOCUMENT MOTOR - Enables you to stop and start the
document handler motor.
124 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
·
·
LAMP - Enables you to turn the lamp on and off and receive a
feedback from the illumination sensor.
CALIBRATION MOTOR - Enables you to test the calibration
zone motor.
To access the COMPONENT TESTS menu:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is
highlighted.
5. Press the Enter key to highlight SCANNER DIAGNOSTICS.
The SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until COMPONENT TESTS is highlighted.
7. Press the Enter key to select COMPONENT TESTS. The
COMPONENT TESTS menu screen is displayed. The black
arrows indicate that the menu contains more options than are
visible. The selected option is highlighted.
COMPONENT TESTS
MOTOR SPEED
LEAD EDGE/TRAIL EDGE
SENSORS
8. Press the Previous or Next key to scroll through the list of
options.
9. When the desired option is highlighted, press the Enter key to
select the option. The screen for the selected option is
displayed.
The MOTOR SPEED option is for use by the Customer Service Engineer
only and requires the entry of the diagnostic password. It allows the
Customer Service Engineer to adjust the Scanner motor speed and
correct magnification error in the process direction.
MOTOR SPEED
If you select this option, the MOTOR SPEED screen is displayed. You
cannot perform any functions in this screen. Press the Exit key to return
to the COMPONENTS TESTS menu screen.
Below is an example of the MOTOR SPEED screen.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 125
MOTOR SPEED
EXPECTED LENGTH: 610
MEASURED LENGTH:
0
PRESS START TO ADJUST SPEED
Select the LEAD EDGE/TRAIL EDGE option to execute the lead
edge/trail edge adjustment diagnostic.
LEAD EDGE/TRAIL
EDGE
To run the LEAD EDGE/TRAIL EDGE diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until COMPONENT TESTS is highlighted.
7. Press the Enter key to select COMPONENT TESTS. The
COMPONENTS TESTS menu screen is displayed.
8. Press the Enter key to select LEAD EDGE/TRAIL EDGE. The
LEAD EDGE/TRAIL EDGE ADJUSTMENT screen is displayed.
LEAD EDGE/TRAIL EDGE
ADJUSTMENT
PRESS START TO BEGIN
9. Insert a black sheet (8.5 X 11) of paper into the Scanner.
10. Press the Start key to begin the diagnostic. When the diagnostic
completes, the last line of the display is replaced with a status
line indicating PASS or FAIL. The last line may also display as
NO RESPONSE FROM SCANNER if the Scanner does not
process the request within the timeout period.
11. Press the Enter key to return to the COMPONENT TESTS menu
screen.
Select the SENSORS option to display the current state of the Scanner
optical paper sensors, calibration home sensor, and the thick document
sensor.
SENSORS
To display the status of the sensors:
126 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until COMPONENT TESTS is highlighted.
7. Press the Enter key to select COMPONENT TESTS. The
COMPONENTS TESTS menu screen is displayed.
8. Press the Enter key to select SENSORS. Depending on the
Document Feed-in Tray configuration, with or without a
Productivity Tray one of the SENSORS screen shown below is
displayed. The first screen below is without the Productivity Tray
The status of each sensor displays as NO. INPUT, EXIT, LEFT,
RIGHT, HOME and REGISTER are the optical paper sensors.
THICK is the Thick Document Sensor. The second screen below
is with the Productivity Tray. When a sensor is activated the icon
O is filled in.
SENSORS
INPUT: NO
EXIT:
NO
HOME: NO
RIGHT:
NO
THICK: NO
LEFT: NO
REGISTER:
NO
SENSORS
O
EXIT:
O
HOME:
THICK: O
O
INPUT:
REGISTER: O
O
O
O
O
O
O
O
O
O
O
9. To check the status of the optical paper sensors:
a) Raise the Thickness Lever to enable an 8.5 X 11 sheet of paper to
be inserted into the Scanner.
b) Insert the sheet of paper centered on the Scanner and slowly push
the paper into the Scanner to check the INPUT, REGISTER, and
EXIT sensors.
The sensors are located underneath the top cover. The photo below
shows the location of each of the sensors on the Document Feed Tray.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 127
A: Left
B: Exit
C: Right
D: Register
E: Input
c) Observe the Display. The status of the covered optical paper sensor
changes from NO to YES if the sensor is okay..
d) Move the sheet of paper fully to the left and right to check the LEFT
and RIGHT sensors.
10. To check the status of the thick document sensor:
a) Raise the Thick Document Lever. The status of the sensor will
change from NO to YES.
b) When finished viewing the status of the thick document sensor, lower
the Thick Document Lever.
11. To check the status of HOME sensor.
a) Raise the Document Handler just enough to access the Calibration
Roll drive gear and still be able to see the Display.
b) Rotate the Calibration Roll one full revolution, the status will change
from NO to YES if the sensor is okay.
128 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
A: Calibration Roll Drive Gear
12. Press the Exit key to return to the COMPONENT TESTS menu
screen.
The MOTOR COMMUNICATIONS test is for use by the Customer
Service Engineer only. However, user access is permitted in the event
that Service instructs the user to perform this test. This test allows the
Customer Service Engineer or user, if directed by the Service Engineer,
to run a motor communications loopback test to assist in diagnosing a
scanner problem.
MOTOR
COMMUNICATIONS
When the Start key is press the message changes to STATUS:, then
after the test completes either a PASS or FAIL status is displayed. If the
status is FAIL, some test values will be displayed., and Service will be
required.
DOCUMENT MOTOR
COMMUNICATIONS
PRESS START TO BEGIN
This option allows you to stop and start the document handler motor.
When you select this option, the DOCUMENT MOTOR screen is
displayed.
DOCUMENT MOTOR
To run the DOCUMENT MOTOR diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 129
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until COMPONENT TESTS is highlighted.
7. Press the Enter key to select COMPONENT TESTS. The
COMPONENTS TESTS menu screen is displayed.
8. Press the Next key until DOCUMENT MOTOR is highlighted.
9. Press the Enter key to select DOCUMENT MOTOR. The
DOCUMENT MOTOR screen is displayed.
DOCUMENT MOTOR
MOTOR: OFF
SPEED:
.125
DIRECTION:
FORWARD
10. Turn the motor on.
a) Press the Previous or Next key to highlight MOTOR.
b) Press the Enter key to confirm your selection.
c) Press the Previous or Next key to select ON. The choices are ON
and OFF.
d) Press the Enter key to confirm your selection.
11. Select the motor speed.
a) Press the Previous or Next key to highlight SPEED.
b) Press the Enter key to confirm your selection.
c) Press the Previous or Next key to select the desired motor speed.
The choices are .125, .250, .500, .750, 1, 1.5, 2, 3 and 4.
d) Press the Enter key to confirm your selection.
12. Select the motor direction.
a) Press the Previous or Next key to highlight DIRECTION.
b) Press the Enter key to confirm your selection.
c) Press the Previous or Next key to select the desired motor direction.
The choices are FORWARD and REVERSE.
d) Press the Enter key to confirm your selection.
13. Press the Start key to activate the motor.
14. Press the Exit key to return to the COMPONENT TESTS menu
screen.
130 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
Select the CALIBRATION MOTOR option to set the calibration zone
motor.
CALIBRATION
MOTOR
To run the CALIBRATION MOTOR diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until COMPONENT TESTS is highlighted.
7. Press the Enter key to select COMPONENT TESTS. The
COMPONENTS TESTS menu screen is displayed.
8. Press the Next key until CALIBRATION MOTOR is highlighted.
9. Press the Enter key to select CALIBRATION MOTOR. The
CALIBRATION MOTOR screen is displayed.
CALIBRATION
MOTOR: OFF
FUNCTION:
GO TO HOME
10. Press the Previous or Next key to select FUNCTION.
11. Press the Enter key to select FUNCTION.
12. Press the Previous or Next key to highlight the desired function.
The choices are GO TO WIDTH, GO TO CALIBRATE, GO TO
HOME, FIND HOME, and ROTATE.
13. Press the Enter key to confirm your selection.
14. Press the Previous or Next key to highlight MOTOR.
15. Press the Enter key to confirm your selection.
16. Press the Previous or Next key to highlight ON. The choices
are ON and OFF. The requested operation will execute.
If a GO TO or FIND function has been selected, the MOTOR field will be
automatically set to OFF when the MOTOR field is once again selected.
If the ROTATE function has been selected, the motor will run
continuously until you set the MOTOR field to OFF.
NOTE: If the Scanner encounters a failure accessing the calibration
motor function, the fourth line of the display will read "FAILURE CODE:"
followed by a two-digit hexadecimal number. The fourth line may also
display NO RESPONSE FROM SCANNER if the Scanner does not
respond to the test request.
XEROX WIDE FORMAT COPY SYSTEM
Main Menu · 131
17. Press the Exit key to return to the Component Tests menu
screen.
The READ NVR option allows the examination of the contents of the
non-volatile RAM (NVR). The service center may ask you to provide this
information when calling for service.
READ NVR
To run the READ NVR diagnostic:
1. Press the Menu key. The MAIN MENU screen is displayed.
2. Press the Next key until DIAGNOSTICS is highlighted.
3. Press the Enter key to select DIAGNOSTICS. The
DIAGNOSTICS menu screen is displayed.
4. Press the Next key until SCANNER DIAGNOSTICS is displayed.
5. Press the Enter key to select SCANNER DIAGNOSTICS. The
SCANNER DIAGNOSTICS menu screen is displayed.
6. Press the Next key until READ NVR is highlighted.
7. Press the Enter key to select READ NVR. The READ NVR
screen is displayed. An "xx" displays for all the NVR values.
READ NVR
00 -07: xx xx xx xx xx xx xx xx
xx xx xx xx xx xx xx xx
08 - 0F:
xx xx xx xx xx xx xx xx
xx xx xx xx xx xx xx xx
10-17:
18-1F:
PRESS START TO BEGIN
8. Press the Start key to display the actual values.
9. Press the Previous or Next key to scroll through the values.
There are 16 rows of values in all.
10. Press the Exit key to return to the SCANNER DIAGNOSTICS
screen.
The PASSWORD option of the DIAGNOSTICS menu is for use by the
Customer Service Engineer only. It allows the Customer Service
Engineer to enter the password for access to password-protected
diagnostic functions.
PASSWORD
If you select this option, the PASSWORD screen is displayed. You
cannot perform any functions in this screen. Press the Exit key to return
to the COMPONENT TESTS menu screen.
PASSWORD
ENTER PASSWORD:
132 ·Main Menu
XEROX WIDE FORMAT COPY SYSTEM
Job Accounting
Job Accounting
NOTE: The JOB ACCOUNTING feature is included in the WIDE
FORMAT COPY SYSTEM 8830, 8850, , 510 Series and 721P. It is an
optional feature on the WIDE FORMAT COPY SYSTEM 8825 and X2
TECH. If you obtain this feature, the System Administrator can enable it
at any time on the WIDE FORMAT COPY SYSTEM 8825 and X2 TECH
by sending a special feature key file to the Printer. Once the feature is
enabled, it remains enabled (even following upgrades to the system
software). Contact your XEROX sales representative for ordering
information.
Overview
JOB ACCOUNTING is a SYSTEM ADMINISTRATION menu option.
Access to it is restricted to the system administrator and requires the
entry of the system administration password.
The JOB ACCOUNTING option allows Scanner and Printer usage to be
recorded in user defined account numbers. Usage is expressed as the
area (not the length) of the media scanned or used.
Job Accounting for the Scanner is controlled through the Scanner
Control Panel. For the WIDE FORMAT COPY SYSTEM 8825, 8830,
8850, 510 Series, and 721P, Job Accounting for the Printer can be set
from either the Printer Control Panel or the Web-based Printer
Management Tool (PMT). For the WIDE FORMAT COPY SYSTEM
721P and X2 TECH, Job Accounting for the Printer can be set from the
Web PMT only.
The Web PMT consists of special Web pages located in the Controller.
They are accessible through either the Microsoft Internet Explorer or the
Netscape browsers. Version 4.0 or higher is required for proper results.
Other Web browsers are not supported and may or may not work
correctly.
Job Accounting can be set on the Scanner or Printer to one of three
modes. The modes are:
·
·
ENABLED all jobs require a valid account number,
OPTIONAL a valid account number is optional for any job
XEROX WIDE FORMAT COPY SYSTEM
Job Accounting · 133
·
DISABLED jobs do not require an account number. The Scanner
and Printer share a common job based accounting database
referred to as the AccXES Account Management Tool. This
AccXES Account Management Tool is composed of two
components, an external accounting software package, installed
on an Administrative workstation, and the job log file that is
created on the Controller. The AccXES Account Management
Tool creates all accounts, assigns the user IDs, gathers all the
account data, manages all the accounts, and provides account
reports.
NOTE: For full information on the new job accounting refer to the
AccXES Account Management Tool Administrator's Guide.
Job Accounting Mode menu
The JOB ACCOUNTING MODE menu allows the system administrator to
access the function for enabling or disabling the Job Accounting Mode at
the Scanner. Access is restricted to the System Administrator and
requires the entry of the system administration password. It provides a
sub-menu of the following choices:
·
JOB ACCOUNTING MODE - Allows the system administrator to
specify the Job Accounting mode for the Scanner. The modes
are as follows:
·
·
·
ENABLED - all jobs require a System Administrator assigned
valid account number,
OPTIONAL - a System Administrator assigned valid account
number is optional for any job
DISABLED - jobs do not require an account number.
To access the Job Accounting menu:
1. Press the Previous or Next key to scroll through the list of
options.
2. When the desired option is highlighted, press the Enter key to
select the option. The menu or screen for the selected option is
displayed.
Submitting jobs
Job Accounting is enabled or disabled on the Scanner and the Printer
independently. Job submission from either device depends on the Job
Accounting mode set for the device.
134 ·Job Accounting
XEROX WIDE FORMAT COPY SYSTEM
If Job Accounting is ENABLED, the following screen is displayed:
From the Scanner
Control Panel
PLEASE ENTER
USER:
Note: If Job Accounting Mode is enabled as OPTIONAL the phrase OR
PRESS ENTER will display at the bottom of the screen. No USER ID is
required, press Enter to continue
You must enter the User ID code assigned to you by the System
Administrator. The account can be an alphanumeric. To enter a numeric
account, press a numeric key once. To enter an alpha character, press
the numeric key associated with the desired letter. Press the numeric key
twice to get the first letter, three times for the second letter, etc. Pressing
a key six to eight times will provide the lower case version of the
respective letter. Pressing the Next key moves the cursor to the right,
which will add a blank space or allow entry of a character. Pressing the
Previous or C/CA keys move the cursor to the left deleting the
character.
Then press ENTER to display the ACCOUNT screen and enter the
account number assigned to you using the numeric keys. Once you do
so, the READY screen is displayed. You can now scan and print copies.
PLEASE ENTER
ACCOUNT:
If Job Accounting Mode is OPTIONAL the above screen will not be
displayed. In either case, the READY screen is displayed after you
press the Enter key. You can now scan and print copies.
If you entered a valid account number, all usage is charged to that
account and is also accumulated under Generic User ID and Account
code. If you did not enter an account number, usage is accumulated
only in the System Account under Generic User ID and Account code
For both the ENABLED and OPTIONAL modes, if you enter an invalid
account, an error message indicated below is displayed. You cannot
access the READY screen if an invalid number is entered
XEROX WIDE FORMAT COPY SYSTEM
Job Accounting · 135
ERROR:
INVALID USER OR ACCOUNT
When Job Accounting Mode is enabled the system examines the
incoming job for a valid account number. If none is found, the job is
rejected, and an error page is printed.
Over the network
NOTE: The 8825/8830 print drivers and AccXES Client Tools (ACTS)
software all have a feature that allows insertion of a job accounting
number. Refer to the user guides for these software products for details.
If Job Accounting is optionally enabled, remote print jobs will be printed
whether or not they have a valid account number. If a valid account
number is present, the job will be charged to the user account and also
accumulated to a system Generic User Id and Account Code. If no
account number is present, the job is charged to a system Generic User
Id and Account Code, just the same as if Job Accounting were disabled.
Once a valid job account number has been entered from the Scanner
Control Panel, all use of the WIDE FORMAT COPY SYSTEM Scanner is
charged to that account. All usage continues to accumulate to that
account until one of the following occurs:
Terminating use
under an account
·
You press the Exit key while either the READY screen or a fault
screen is displayed.
·
The FEATURE timer times out due to no activity. The default
value is 5 minutes, but this value can be changed. Refer to
"TIMERS" in the "Main Menu" section for information about
changing the value.
When an account is no longer in use, the PLEASE ENTER ACCOUNT
screen is displayed.
NOTE: To avoid incorrect accounting, always ensure that the PLEASE
ENTER USER screen is displayed before leaving the WIDE FORMAT
COPY SYSTEM for the next operator. Press the Exit key to obtain this
screen.
136 ·Job Accounting
XEROX WIDE FORMAT COPY SYSTEM
Cleaning and maintenance -
Scanner
Cleaning and maintenance - Scanner
For the Scanner to do its best job, the Platen Glass, Document Drive
Rolls, Backer Roll, Calibration Strip, and Document Feed Tray must be
kept clean. This requires some daily and monthly cleaning and
maintenance activities.
Daily activities
Clean the Platen Glass, Document Drive Rolls, and Backer Roll. See the
"Cleaning the Platen Glass and Document Drive Rolls" section on the
next page.
Inspect the Document Feed Tray and clean as required.
Monthly activities
Clean the Calibration Strip. See the "Cleaning the Calibration Strip"
section on the next page.
Inspect the Platen Glass for chips and scratches.
If the Platen Glass is chipped or scratched, and these defects are visible
in the scanned images, call XEROX service.
The following illustration depicts the Scanner components that require
cleaning.
XEROX WIDE FORMAT COPY SYSTEM
Cleaning and maintenance - Scanner · 137
A: Platen Glass
D: Document Drive Rolls (front)
B: Backer Roll
E: Document Feed Tray
C: Document Drive Rolls (rear)
Cleaning the Platen Glass and
Document Drive Rolls
Perform the following steps daily:
1. Open the Top Cover.
2. Dampen a clean, lint-free towel (600S4372) with platen glass
cleaning fluid (Xerox 43P81).
3. Wipe the Platen Glass with the towel.
4. Visually inspect the Platen Glass to ensure that all dirt, glue, and
other residue have been removed.
5. Place a small amount of the cleaning fluid on the towel and clean
the front and rear Document Drive Rolls. Rotate the Rolls as you
clean them to ensure that the entire roll surface is clean.
6. Place a small amount of the cleaning fluid on the towel and wipe
the white Backer Roll.
NOTE: The Backer Roll is located on the underside of the Top Cover.
The Backer Roll may rotate as you clean it. This is normal behavior.
7. Close the Top Cover.
138 ·Cleaning and maintenance - Scanner
XEROX WIDE FORMAT COPY SYSTEM
Cleaning the Calibration Strip
Perform the following steps monthly:
1. Press the Menu key, then scroll to the Diagnostic and press the
Enter key. Scroll to CLEAN CAL ZONE and press the Enter key.
Press the Enter key to select CLEANING POSITION.
NOTE: The Top Cover must be closed while running this test.
2. Raise the Top Cover.
3. Inspect the Calibration Strip.
4. Place a small amount of platen glass cleaning fluid (Xerox
43P81) on a clean, lint-free towel (600S4372) and clean the
Calibration Strip.
5. Lower the Top Cover.
6. Press the Enter key to select HOME POSITION.
7. Press the Exit key to exit the CLEAN CAL ZONE
8. Press the Menu key to return to the READY screen. The
Calibration Strip automatically returns to its home position.
XEROX WIDE FORMAT COPY SYSTEM
Cleaning and maintenance - Scanner · 139
Problem solving
Problem solving
This section contains a problem-solving table and an error message table for
help in resolving problems with the WIDE FORMAT SCAN SYSTEM.
Identify the problem you are experiencing and follow the step(s) indicated in the
table for fixing the problem. If the procedures do not restore normal Scanner
operation, call for service.
For help in solving problems with the Printer or the Printer media, refer to the
applicable Printer Operator Manual.
Table 7. Problem Solving Table
Problem
Power on
First solution to try
Second solution to Third
try solution to
try
The Exposure Lamp does
not illuminate when the
Scanner is switched on.
Ensure that the Power Cord is connected Check that the Power Call for
to the Scanner and to the correct power
source.
On/Off Switch is in the Service
on (I) position.
The Scanner Control Panel Ensure that the IEEE 1394 cable is
Ensure that the DDS
option is set to
Enabled.
continuously displays a
clock face and the System
does not initialize.
connected to both the Scanner and the
Controller. Check that the cable was not
forced in the connector incorrectly
NOTE: For the
8825/8830 Printer,
you can change this
setting from either the
CONTROLLER
CONFIGURATION
screen of the Printer
Control Panel or the
PRINTER
SETUP/Miscellaneous
page of the Web PMT.
After the DDS is set to
enabled, wait 30
seconds, then power
the system off then on
(rebooted).
For the 721P Printer,
140 · Problem solving
XEROX WIDE FORMAT COPY SYSTEM
this change can be
made from the Web
PMT only. Refer to
the
8825/8830/8850/510
Series/721P Controller
Setup Manual or the
Web Printer Manager
Tool User Guide for
more information.
Constant Scanner NOT
READY message
Lift the Document Handler
Switch off the Scanner
Call for Service
Switch off the Printer/Controller
Switch on the Scanner and wait for the
display to indicate P
Switch on the Controller then Printer.
Corrupted or unclear
messages after powering
the scanner off then on.
Ensure the System was powered off then . Call for Service
on correctly:
Switch off the Scanner
Switch off the Printer/Controller
Switch on the Scanner and wait for the
display to indicate P
Switch on the Controller then Printer.
Scanner control
The Scanner does not scan Press the Start key or enable
when a document is
inserted.
AUTOSCAN. See "Scanner control" in
the "Main Menu" section for more
information.
The Scanner measures the Clean the Platen Glass.
width of the original
Turn AUTOWIDTH off.
See "Scanner Control"
in the "Main Menu"
section for more
Open the Upper Document Transport..
incorrectly. The copy is
either wider than the
original or the copy is
clipped.
Look for a row of 10 holes across the
Feed-in Shelf next to the Platen Glass. If
the holes are present, press the Menu
key and scroll to
information.
CONFIGURATION>SCANNER
CONTROL> MODE and check if mode is
set to PRODUCTIVITY. If it is, ensure
that the media series setting for the
PRODUCTIVIY matches the media series
being used in the Printer. If the media
seies matches, set the MODE to
AUTOWIDTH/AUTOCENTER and call for
service.
When the Scanner is set to Raise the Thick Document Lever to
Set the Scanner to
exit to the rear. See
exit to the front, the
release the document. Be sure to lower
document is difficult to
remove from the Scanner.
the Thick Document Lever before making "Scanner Control" in
the next copy/scan.
the "Main Menu
section for more
information.
Document feed
The Scanner will not accept Ensure that both the Scanner and the
If the thin document
has a torn or dog-
eared lead edge, try
Insert the
document in a
document
carrier.
a thin document (less than
.03 in (1 mm) thick).
Printer are powered up and initialized.
Ensure that the Thickness Lever is
adjusted correctly for the document being feeding a different
XEROX WIDE FORMAT COPY SYSTEM
Problem solving · 141
scanned.
edge first.
The Scanner will not accept Ensure that both the Scanner and the
Set the Thick
a thick document.
Printer are powered up and initialized.
Document Lever to its
next higher setting.
Thick documents may
require operator
assistance.
The Scanner measures the Refer to Cleaning the Platen Glass and
Turn the AUTOWIDTH
off. See “Scanner
width of the original
incorrectly. The copy is
either wider than the
original or the copy is
clipped
Document Drive Rolls. Wipe the
Document Feed Tray with anti-static fluid. Control” in the “Main
Menu” section for
more information
See the second item above in Scanner
Control
When the Scanner is set to Raise the Thick Document Lever to
Set the Scanner to
exit to the rear. See
exit to the front, the
release the document. Be sure to lower
document is difficult to
remove from the Scanner
the Thick Document Lever before making “Scanner Control” in
the next copy/scan.
the “Main Menu”
section for more
information.
Width detection failed when Enter the document width.
scanning transparent
documents. Width sensors
Turn AUTOWIDTH off
and refer to “Scanner
Control” in the Main
Menu
in most cases will not detect
transparent documents.
Not Ready Media Jam
Refer to Cleaning the Platen Glass and
Document Drive Rolls. Wipe the
Document Feed Tray with anti-static fluid. damaged, use a
If the document is
folded, worn or
For thick
documents,
set the Thick
document carrier or try Document
feeding a different
edge.
Lever to its
next higher
setting. Thick
documents
may require
operator
assistance.
The Scanner does not
position the document
correctly before scanning.
Ensure that you are inserting the
document correctly.
Check the operation of
the optical paper
sensors. See
"Sensors" in the "Main
Menu" section for
more information.
Center the document between the marks
on the Document Feed Tray.
Smoothly insert the document into the
feed mechanism so that the lead edge of
the document is against the rollers before
the Scanner begins to stage the
document.
Image quality
Vertical lines and streaks
are visible in the copy.
Clean the Platen Glass.
Visible document edges on Try a lighter Contrast setting.
the copy.
Dark spots or smudges
appear on the copy.
Clean the Platen Glass.
Inspect the original
and clean it if
necessary.
Adjust the
Copy setting
for best image
quality.
The copy image is too light. Adjust the Copy setting for best image
quality.
Rotate the original 90
degrees.
142 · Problem solving
XEROX WIDE FORMAT COPY SYSTEM
The image density on the
copy varies from light to
dark.
Rotate the original 90 degrees.
Adjust the Copy
setting for best image
quality.
Copies made in Photo
mode have geometric
patterns.
Set the Original, Type to Normal and the Set Original, Type to Try a lighter
Background Suppression to Off. Line and Background Contrast
Suppression off.
setting.
Fine lines on the original do Enable the LINE MODE LINE
Adjust the Copy
not appear on the copy
when the image size is
reduced.
PRESERVATION option. See "Imaging" setting for best image
in the "Main Menu" section for more
information.
quality.
Gray areas appear in the
copy at the location of
creases or folds in the
original document.
Refold the document in the reverse
direction to flatten the creases or folds.
Error messages
An error message is
displayed on the Scanner
Control Panel.
Locate the message in Table 8, "Error
messages," in this s ection and perform
the corrective action indicated.
Table 8. Error Code Table
Corrective action
Error message
Probable cause
40000001: ERROR
The Job Log File size has
reached the maximum space
allocated for it
Contact your System Administrator
ACCOUNTING DISK FULL
40000002: ERROR
The number of Job Records in
the Job Log File has reached the
maximum as defined by the
AccXES Account Management
Tool
Contact your System Administrator
CONTROLLER FAULT -
50000001
The Controller has developed a
"memory is full" internal fault.
Large documents using Auto
Reduction/Enlargement or Auto-
Rotate may cause this fault.
Also, Photo and Mixed/Custom
modes require significantly more
memory than Line mode.
Remove document. Press Start to print the
job
The Controller has developed a
“memory is full” internal fault.
Large documents using Auto
Reduction/Enlargement or Auto
Rotate may cause this fault. Also,
Photo and Mixed/Custom modes
require significantly more memory
than Line mode.
Remove the document. Wait for previous
scans to finish printing. End the current set
or print it if a set is in progress. Rescan the
document.
CONTROLLER FAULT -
50000002
CONTROLLER FAULT -
50000003
A task controlling the scanner
received and unrecognized
request from the task controlling
the scanner control panel.
Power off the System. .
Check that all cables are connected
correctly.
CONTROLLER FAULT -
50000004
Power on the System.
CONTROLLER FAULT -
50000005
See the "Powering off the System" and
"Powering on the System" sections for more
information.
XEROX WIDE FORMAT COPY SYSTEM
Problem solving · 143
CONTROLLER FAULT -
50000007
A software problem was
encountered in controlling the
Scanner.
Power off and power on the System. See
the "Powering off the System" and "Powering
on the System" sections for more
information.
CONTROLLER FAULT -
50000008 - DOCUMENT
JAM
A document jam has occurred in
the Scanner.
Remove the jammed document. Scan the
document again.
CONTROLLER FAULT -
50000011 - SCANNED
IMAGE LOST
AccXES firmware prior to version Allow the jobs in the queue to print Then
9.5 supported a maximum of 128 rescan the document.
active jobs in the printer queue.
Scans made after the maximum
were refused and a scan error
was declared.
AccXES firmware 9.5 and greater reserves 8
jobs for scan to net and copy jobs. This
provides sufficient capability for scans and
copy jobs even when there is a high volume
of print jobs on the network.
SCANNER FAULT -
5000000B - CHECK
SCANNER
A fault has occurred in
communicating with the Scanner. connected at both ends.
Check that the IEEE 1394 cable is properly
Check that the Scanner is still connected to
VERIFY SCANNER IS
POWERED AND
PROPERLY CONNECTED
the AC power and is still switched on.
Power off and power on the System. See
the "Powering off the System" and "Powering
on the System" sections for more
information.
CONTROLLER FAULT -
50000012 - MEMORY FULL
The file system or memory is full. Retrieve or delete some documents to create
more space. Then rescan the document.
CONTROLLER FAULT -
5000013 - MEMORY FULL
CONTROLLER FAULT -
50000014 - MEMORY FULL fast. Memory is full.
Documents were scanned too
Wait for previously scanned documents to be
processed and stored on the hard disk.
Then scan the current document again.
CONTROLLER FAULT -
50000015
An error occurred saving the
scanned image to a disk.
Do not scan until the interrupted job is
finished. Check that the SCSI cable or IEEE
1394 cable is connected correctly.
SCANNER FIRMWARE
Scanner firmware is not at current Update the Scanner firmware.
VERSION FAULT -50000020 version to support Controller
firmware version 10.0. Scanner
firmware must be at version 3.0.9
or later
SCANNER FAULT -
COMPLEX DOCUMENT
An error occurred during
processing due to the complexity
of the image that the document
contains.
Rescan the document.
WARNING: xxxx
The image submitted for printing
is corrupted or does not conform
to the standards for the format.
Recreate the image and try again.
LL codes appear
intermittently while
documents are scanned
Intermittent scanner and/or
software problems.
Power the system off then on. If the
problem persists, call for service.
144 · Problem solving
XEROX WIDE FORMAT COPY SYSTEM
Specifications
Specifications
Speed
8825
8830
8850
510 Series 721P
2 inches per second
4 inches per second
1 inch per second color
7.33 inches per second*
standard
optional
optional
standard
optional
standard standard
optional optional
standard
optional
standard
* Requires Turbo III Feature Key, HFT Controller running version 9.0 or higher
software, WIDE FORMAT SCAN SYSTEM firmware version 3.0.7A or higher
Input Document
Maximum document:
Maximum Scan Width:
Minimum document:
42" x 100 feet (1.07m x 30.5 m)
36" (914 mm)
A size 8.5 x 11 (216mm x 279mm)
A4 size (210mm x 297mm)
0.0023 to 0.50 " (0,06mm to 13mm)
Document Thickness:
Thick Document Weight: 6 lbs (2.72 kg) max.
Scanner Resolution
Copying:
200, 300, 400 dots per inch
Scan to Net
75, 100, 200, 300, 400 dots per inch
25% to 400% in ± 0.1%
increments
Magnification:
Temperature
Minimum:
55 F (10 C)
90 F(32 C)
Maximum:
20% - 80%
Humidity:
XEROX WIDE FORMAT COPY SYSTEM
Specifications · 145
0 - 6560 feet
0 - 1.995 km
Maximum Elevation:
Heat Emission
Running:
690 BTU/hr
Power Consumption
Standby:
130 W
200 W
Running:
Electrical
Requirements
Voltage (AC):
100 - 120 VAC
200 - 240 VAC
4 amps
Current:
3 amps
50/60 Hz
Frequency:
Audible Noise
Standby:
33.7 dBA
52.1 dBA
56.4 dBA
Running:
Impulse:
146 · Specifications
XEROX WIDE FORMAT COPY SYSTEM
Appendices
Appendix 1
Table 9 below shows the minimum and maximum scanning speeds for a 36 inch
(914 mm) wide document in Line, Mixed, and Photo modes at various
resolutions.
NOTE: Speeds are given in inches per second (IPS) and centimeters per
second (cm/s).
NOTE: Thick documents are scanned at a maximum speed of 4.00
IPS/10.16cm/s in all Modes.
Table 9. Scanning resolutions and speeds
Turbo II
DPI Pixel Min
DepthIPS/ cm/s IPS/ cm/s
Turbo III
Min
2 IPS
Min
Mode
Max
Max
Max
IPS/ cm/s IPS/ cm/s IPS/ cm/s IPS/ cm/s
Line (copy or scan 400 1 bit 4.00/10.16 4.00/10.16 7.00/17.78 7.00/17.78 2.00/5.08 4.00/10.16
mode)
Line (scan mode) 300 1 bit 4.00/10.16 4.00/10.16 4.00/10.16 4.00/10.16 2.00/5.08 4.00/10.16
Line (scan mode) 200 1 bit 8.00/20.32 8.00/20.32 8.00/20.32 8.00/20.32 4.00/10.16 4.00/10.16
Line (scan mode) 100 1 bit 8.00/20.32 8.00/20.32 8.00/20.32 8.00/20.32 4.00/10.16 4.00/10.16
Normal and Photo 75
only (scan mode)
4 bit 2.00/5.08 4.00/10.16
2.00/5.08 4.00/10.16
Photo (scan mode) 400 8 bit 0.5/1.27
4.00/10.16 4.00/10.16 4.00/10.16 0.5/1.27
4.00/10.16
Photo (scan mode) 300 8 bit 1.00/2.54 4.00/10.16 4.00/10.16 4.00/10.16 1.00/2.54 4.00/10.16
Photo (copy or
scan mode)
200 8 bit 2.00/5.08 8.00/20.32 8.00/20.32 8.00/20.32 2.00/5.08 4.00/10.16
Photo (scan mode) 100 8 bit 8.00/20.32 8.00/20.32 8.00/20.32 8.00/20.32 4.00/10.16 4.00/10.16
XEROX WIDE FORMAT COPY SYSTEM
Appendices · 147
Appendix 2
Paper sizes supported by the 8825, 8830, 8850 510 Series, and 721P Printers
and the Controller with Firmware 9.1 or higher are shown in Table 10.
The X2 TECH Color Printer is available in two configurations, capable of printing
on media up to 36" wide, or on media up to 54" wide, depending upon your
equipment order and installation. The Media types supported by your X2 TECH
printer and AccXES firmware can be checked using the Media Page of the Web
PMT. Available roll sizes for each supported media type can be quickly and
easily checked from the supplies page of the XEROX website at www.xerox.com.
Table 10. Printer paper sizes
Paper size
Dimension
8825/8830/8850 721P
/510dp Series
ISO A0
ISO A1
ISO A2
ISO A3
ISO A4
ISO B1
ISO B2
ISO B3
ISO B4
ANSI A
841 x 1189 mm
594 x 841 mm
420 x 594 mm
297 x 420 mm
210 x 297 mm
707 x 1000 mm
500 x 707 mm
353 x 500 mm
250 x 353 mm
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
8.5 x 11 (215.9 x
279.4 mm)
ANSI B
11 x 17 in. (279.4
x 431.8 mm)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ANSI C
17 x 22 in. (431.8
x 558.8 mm)
ANSI D
22 x 34 in. (558.8
x 863.6 mm)
ANSI E
34 x 44 in. (863.6
x 1117.6 mm)
Architectural A
Architectural B
Architectural C
Architectural D
Architectural E
Architectural 30"
9 x 12 in. (228.6 x
304.8 mm)
12 x 18 in. (304.8
x 457.2 mm)
18 x 24 in. (457.2
x 609.6 mm)
24 x 36 in. (609.6
x 914.4 mm)
36 x 48 in. (914.4
x 1219.2 mm)
30 x 42 in. (76.2 x
1066.8 mm)
148 · Appendices
XEROX WIDE FORMAT COPY SYSTEM
Appendix 3
Table 11 below shows roll sizes supported by the 8825, 8830, 8850,510 Series
and 721P Printers.
Table 11. Printer roll sizes
Roll size
Width
8825/8830/8850 /721P
/510dp Series
ISO Roll A0
ISO Roll A1
ISO Roll A2
ISO Roll A3
ISO Roll A0
Roll 891
841 mm
594 mm
420 mm
297 mm
880 mm
891 mm
900 mm
11 in.
X
X
X
X
X
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
Roll 900
X
X
X
X
X
X
X
X
X
X
X
X
X
ANSI Roll 11
ANSI Roll 17
ANSI Roll 22
ANSI Roll 34
ARCH Roll 12
ARCH Roll 18
ARCH Roll 24
ARCH Roll 30
ARCH Roll 36
ISO B3
17 in.
22 in.
34 in.
12 in.
18 in.
24 in.
30 in.
36 in.
353 mm
500 mm
707 mm
364 mm
515 mm
728 mm
620
ISO B2
ISO B1
JIS B3
JIS B2
JIS B1
X
X
X
750
-
860
-
Appendix 4
Default fonts installed in the Controller with Firmware 9.0 are shown in the list
below.
·
·
·
·
HP Stick Font
HP2 Stick Font
HP Stick Set 99 Font
HP2 Stick Font - Proportional
XEROX WIDE FORMAT COPY SYSTEM
Appendices · 149
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Test Print Stick Font
HP2 Stick Font Latin
CalComp Stick Font
CalComp Stick Font - Proportional
VG-CalComp
VG-CalComp - Proportional
VG-Hershey-BoldItalic - Proportional
VG-Hershey-Italic - Proportional
VG-Hershey-SanSerif - Proportional
VG-Hershey-Serif - Proportional
VG-Hershey-Serif-Bold - Proportional
VG-CalCompOld/Norwegian/Swedish
VG-CalCompOld/Norwegian/Swedish - Proportional
VG-Energy-1
VG-Energy-2
VG-Energy-3
VG-Energy-4
VG-Energy-5
VG-German
VG-German - Proportional
VG-Simplex/French
VG-Simplex/French - Proportional
OCRB
Courier
Courier-Bold
Courier-BoldItalic
Courier-Italic
NeueClassic-Roman
NeueClassic-Bold
NeueClassic-BoldItalic
NeueClassic-Italic
NeueModern
NeueModern-Bold
NeueModern-BoldItalic
NeueModern-Italic
Symbol
150 · Appendices
XEROX WIDE FORMAT COPY SYSTEM
Appendix 5
File formats supported by the Controller with Firmware 10.0 are shown in the list
below.
·
·
·
·
·
·
·
·
·
CalComp 906/907/PCI
HP-GL (HP7585/6)
HP-GL/2
TIFF 6.0
CGM
VCGL
VDS (VRF, Block Raster, Compressed Raster, VOF)
Versatec Raster/Green Sheet
Post Script
Appendix 6
The HFT and the KLF Controller (X2 TECH) have four LED status indicators as
shown in Table 12 below.
Table 12. UP8 Controller LED status indicators
LED Number
Color
Indicated Condition
LED 1
Green
"Ready." Indicates that the Controller is
powered up and ready to process
incoming jobs.
LED 2
LED 3
Green
Yellow
"Busy." Indicates that the Controller is
busy processing a job.
"Mismatch." Indicates that a media
mismatch, which may be blocking the
print queue, has occurred. Also
displayed when the Controller's
Accounting disk is full, or when the
Controller has reached its Accounting
record limit. Check the Web PMT's Main
Page to determine the problem.
LED 4
Red
"Attention." Indicates that a Printer or
Finisher fault has occurred. May indicate
a paper jam, out of toner condition, out of
media condition, or a communications
problem with one of the devices.
During power-on self test (POST), the firmware will light LEDs 2, 3, and 4. After
POST has successfully completed, LEDs 2, 3, and 4 will be switched OFF, and
LED 1 will be switched ON. If POST did not successfully complete, all 4 LEDs
will be switched OFF (i.e., they will be unlit).
XEROX WIDE FORMAT COPY SYSTEM
Appendices · 151
Appendix 7
Appendix 7 shows the structure of the Main Menu. The menu tree below shows
the top level of the Main Menu. The pages that follow contain menu trees for
each of the four top-level options.
Main Menu
Configuration
System Information
System Administration
Diagnostics
The menu tree below shows the structure of the Configuration option of the Main
Menu.
Configuration
Localization
Language
Copy Options
Image
Enhancements
Timers
Scanner
Control
Control Panel
Power
Saver
Color IQ
Feature
Printer Interrupt
Dynamic Background Removal File Deletion
Beeper
Text
Default Mode
Autoscan
Normal Mode
Document Return
Mode:
§
§
§
Manual Width
Autowidth
Autowidth/Auto
Center
Productivity
§
Media Series
Custom R/E
Preset
Imaging
Custom Media
Auto-Rotate
Reduction Line Preservation
152 · Appendices
XEROX WIDE FORMAT COPY SYSTEM
The menu tree below shows the structure of the System Information option of the
Main Menu.
System Information
System Description
Recent Fault List
Configuration Prints
Copier Configuration
Printer Configuration
Printer Settings
Configuration Prints
Printer
Finisher
Scanner
Controller
Control Panel
The menu tree below shows the structure of the System Administration option of
the Main Menu.
System Administration
Password
Change Password
Security Settings
The menu tree below shows the structure of the Diagnostics option of the Main
Menu.
Diagnostics
Clear Scanner
Usage
Usage Meters
Scanner
Diagnostics
Installation Test
Print
Password
Scanner (Ft2)
Media Linear
Scanner (Ft2)
Media Area
Image Path
Scan Bar
Full System Test
Write NVR
Component Test
Motor Speed
Lead Edge/Trail Edge
Sensors
Reset NVR Defaults
Scanner Reliability Meter
Scanner Faults (Ordered)
Scanner Faults (Counts)
Clear Scanner Fault Log
Clean Calibration Zone
Read NVR
Motor Communications
Document Motor
Calibration Motor
XEROX WIDE FORMAT COPY SYSTEM
Appendices · 153
Prepared by:
Xerox Corporation
Global Knowledge & Language Services
800 Phillips Road
Building 845-17S
Webster, New York 14580-9791
USA
Printed in the United States of America
AccXES is a trademark of the Xerox Corporation 2003, 2004. All other
product names mentioned herein are trademarks of their respective
companies. All rights reserved.
701P41762
3/2004
|