Xerox C424 User Manual

WorkCentre® C2424 Copier-Printer  
User Safety  
Your system and the recommended supplies have been designed and tested to meet strict safety  
requirements. Attention to the following information will ensure the continued safe operation  
of your system.  
Electrical Safety  
Use the power cord supplied with your system.  
Plug the power cord directly into a properly grounded electrical outlet. If you do not know  
if an outlet is grounded, ask an electrician to check the outlet.  
Do not use a ground adapter plug to connect the system to an electrical outlet that does not  
have a ground connection terminal.  
Do not use an extension cord or power strip.  
Warning  
Avoid the potential of electrical shock by ensuring that the system is properly grounded.  
Electrical products may be hazardous if misused.  
Do not place the system in an area where people might step on the power cord.  
Do not place objects on the power cord.  
Do not block the ventilation openings. These openings are provided to prevent overheating  
of the system.  
Do not drop paper clips or staples into the system.  
Warning  
Do not push objects into slots or openings on the system. Making contact with a voltage  
point or shorting out a part could result in fire or electrical shock.  
If you notice noises or odors that are not associated with your normal system operation:  
1. Turn off the system immediately  
2. Disconnect the power cord from the electrical outlet  
3. Call an authorized service representative to correct the problem.  
Copyright © 2005 Xerox Corporation. All Rights Reserved.  
A-1  
Follow all warnings and instructions marked on, or supplied with, the system, options and  
supplies.  
Caution  
Use of other than Genuine Xerox WorkCentre C2424 Solid Ink may affect print and copy  
quality and system reliability. It is the only ink designed and manufactured under strict  
quality controls by Xerox for specific use with this system. The Xerox Warranty, Service  
Agreements, and Total Satisfaction Guarantee do not cover damage, malfunction, or  
degradation of performance caused by use of non-Xerox supplies or consumables, or the  
use of Xerox supplies not specified for this system.  
Note  
The Total Satisfaction Guarantee is available in the United States and Canada.  
Coverage may vary outside these areas; please contact your local representative for  
details.  
System Location  
Place the system in a dust-free area within a temperature range of 50 degrees F to  
90 degrees F (10 degrees C to 32 degrees C) and a relative humidity range of 10 percent to  
80 percent.  
Place the system in an area where there is adequate space for ventilation, operation, and  
servicing. The recommended minimal spacing is:  
30 cm (11.8 in.) above, measuring from the top of the document feeder  
24 cm (9.5 in.) behind  
10 cm (3.9 in.) on the left side of the system  
37 cm (14.6 in.) on the right side of the system, to allow access to the maintenance  
unit and waste tray.  
Do not block or cover the slots and openings on the system. The system may overheat  
without adequate ventilation.  
For optimum performance, use the system at elevations below 2,438 m (8,000 ft.).  
Do not place the system on a carpeted location such as a carpeted floor. Airborne carpet  
fibers can be pulled into the system and cause print- and copy-quality problems.  
Do not place the system near a heat source.  
Do not place the system in direct sunlight.  
Do not place the system in line with the cold air flow from an air conditioning system.  
Place the system on a level, solid non-vibrating surface with adequate strength for the  
weight of the system. It should be within 2 degrees of horizontal with all four feet in solid  
contact with the surface. The base system weight without any packaging materials is  
approximately 42 kg (93 lbs.).  
WorkCentre® C2424 Copier-Printer  
A-3  
Moving the System  
Caution  
Parts of the system are hot. To avoid personal injury or damage to the system, allow the  
ink to solidify. Run the shut-down procedure to cool the system quickly. Wait at least  
30 minutes for the system to cool completely before moving or packing it.  
Always allow the system to cool before it is moved to avoid ink spills which can damage  
the system.  
Use the shut-down procedure at the control panel (Shut Down for Moving System)  
for best results.  
Never move the system if you receive a Power Down Error-Head not Parked  
message at the system’s control panel. This message means the system is not ready to be  
moved. If the printhead is not locked, the system can be damaged during shipment.  
Always turn off the system using the power switch, located under the interface cover on  
the right side of the system, and unplug all cables and cords. Do not turn off the system by  
pulling the power cord or using a power-strip with an on/off switch.  
Always secure the scanhead shipping restraint on the left side of the scanner to lock the  
scanhead before removing the scanner portion of the system. Shipping the scanner with  
the scanhead unlocked can damage the scanner.  
al  
in  
rig  
O
ype  
T
s
ic  
ut  
ph  
tp  
ra  
G
u
O
y
lit  
a
u
Q
s
d
o
e
R
Pr  
i-  
H
d
e
ns  
2-Sided  
a
h
n
E
rd  
a
d
n
ta  
S
t
s
a
F
Color  
Mode  
B/W  
utput  
O
Color  
Uncollated  
Collated  
2424-107  
Always remove the document feeder before shipping the system.  
Always remove the scanner before shipping the system.  
WorkCentre® C2424 Copier-Printer  
A-4  
The system is heavy and must be lifted by two people. The illustration below shows the  
proper technique for lifting the system.  
42 kg  
93 lbs.  
2424-109  
Always move the system separately from optional Trays 3 and 4.  
When shipping the system, repack the system using the original packing material and boxes or  
a Xerox repackaging kit. Additional instructions for repacking the system are provided in the  
repackaging kit. If you do not have all the original packaging, or are unable to repackage the  
system, contact your local Xerox service representative.  
Caution  
Failure to repackage the system properly for shipment can result in damage to the  
system. Damage to the system caused by improper moving is not covered by the  
Xerox warranty, service agreement, or Total Satisfaction Guarantee. The Total  
Satisfaction Guarantee is available in the United States and Canada. Coverage may  
vary outside these areas; please contact your local representative for details.  
Operating Safety Guidelines  
Keep hands, hair, neckties, etc., away from the exit and feed rollers.  
Do not remove the paper source tray that you selected in either the printer driver or control  
panel.  
Do not open the doors while the system is busy.  
Do not move the system while busy.  
WorkCentre® C2424 Copier-Printer  
A-5  
Symbols Marked on the System  
Danger, high voltage.  
Use caution (or draws attention to a particular  
component). See the manual(s) for information.  
Avoid pinching fingers in the system. Use  
caution to avoid personal injury.  
Keep hands clear to avoid personal injury.  
Hot surface on or in the system. Use caution to  
avoid personal injury.  
WorkCentre® C2424 Copier-Printer  
A-6  

Toshiba Rav Sm561at E User Manual
Ricoh Aficio Ld260 User Manual
MAKITA XWT08 User Manual
KENWOOD KVT 696 User Manual
HP ELITEDESK 705 G2 SFF User Manual
Ct50 Manual
BROTHER FAX 575 User Manual
BLAUPUNKT LOS ANGELES MP74 7 644 815 310 User Manual
BLACK DECKER LI2000 User Manual
BLACK DECKER KS501 User Manual