Soleus Air Air Conditioner Pe1 09r 30 User Manual

9,000 BTU Portable Air Conditioner  
PE1-09R-30  
Operating Instructions  
Model No. PE1-09R-30  
®
© 2006 Soleus Air International  
PACKAGE CONTENTS  
Portable Air Conditioner  
Exhaust Hoses (2)  
Hose Adapters (2)  
W indow Kit Adapter (2)  
Remote Control  
AAA Batteries (2)  
W indow Kit - 3 Sliding Panels (1 dual hose panel, 2 extension panels)  
Air Intake and Outlet Covers (2)  
Owner‘s Manual  
W ARNING: This unit has a voltage rating of 115  
volts. The cord has a plug as shown in A. An adapter as  
shown in C is available for connecting three-blade  
grounding-type plugs to two-slot receptacles. The  
grounding lug extending from the adapter must be con-  
nected to a permanent ground such as a properly  
grounded outlet box. The adapter should not be used if  
a three-slot grounded receptacle is available.  
DO NOT DEFEAT THE SAFETY PURPOSE OF  
THE GROUNDED PLUG.  
SPECIFICATIONS  
MODEL  
PE1-09R-30  
9,000 BTU/H  
1200 W atts  
50 pts/Day  
980 W  
ñ
The cooling capacity is meas-  
ured at an ambient temperature  
of DB 86 °F, W B 78 °F.  
COOLING CAPACITY  
HEATING CAPACITY  
DEHUMIDIFYING CAPACITY  
ñ
Noise level is measured at a  
distance of 3.28 ft away from  
the front of the unit, when the  
unit is in cooling mode.  
COOLING  
HEATING  
AIR FLOW VOLUME  
POW ER  
1350W  
177 CFM  
ñ
ñ
Power consumption is meas-  
ured when the fan runs at the  
highest speed setting.  
115 V~ 60 HZ  
9/12 AMP  
HEATING/COOLING  
POW ER SOURCE  
SOUND PRESSURE LEVEL  
NET W EIGHT  
46 dB(A)  
75 Lbs  
These specifications are for  
reference only. For actual data,  
please refer to the rating label  
on the back of the unit.  
COOLING  
60.8̧-108̧ꢀ  
23̧-89.6̧ꢀ  
OPERATING  
TEMPERATURE  
HEATING  
ñ
If the environment temperature  
is higher than the max operat-  
ing temperature or lower than  
the minimum operating tem-  
perature, the air conditioner  
may not work properly.  
ASSEMBLED  
PACKAGE  
17.75“ W x 18.25“ D x 32.5“ H  
DIMENSIONS  
21“ W x 18.5“ D x 34.5“ H  
R22  
REFRIGERANT  
3
PRODUCT DIAGRAM  
Control Panel  
Louvers  
Signal Receptor  
Casters  
Filter Compartment  
4
PARTS & ASSEMBLY  
PARTS  
EXHAUST HOSE  
W INDOW KIT  
ASSEMBLY & INSTALLATION  
INSTALLATION  
W hen the unit is operating as an air conditioner or dehumidifier, the unit draws in fresh outdoor air and exhausts hot air  
out of the room to complete the air exchange. W hen the unit is operating in fan or heater modes, no outdoor air exchange  
takes place. The window kit and exhaust hose do not need to be installed when the unit is used as a fan or heater.  
NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors up to 8 ft. long  
(approximate length).  
MOUNTING THE EXHAUST HOSES  
ñ
Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove  
packaging and locate components.  
ñ
ñ
Extend both ends of the exhaust hoses approximately 6 inches.  
Screw the window kit adapter onto one end of the exhaust hose clockwise. Screw the hose adapter onto  
the other end of the exhaust hose clockwise. Repeat on the other exhaust hose.  
ñ
ñ
Remove outlet covers from the back of the unit by screwing them counter-clockwise, then lifting up.  
Mount the exhaust hoses onto the back of the unit by locking the hose adapters into place.  
5
DUAL HOSE W INDOW KIT INSTALLATION  
6
CONTROL PANEL, DISPLAY, & OPERATING INSTRUCTIONS  
CONTROL PANEL & MULTI-COLOR DISPLAY  
CONTROL PANEL  
TEMP & TIMER SELECTION  
POW ER BUTTON  
MODE BUTTON  
TIMER BUTTONS  
SW ING (LOUVER  
OSCILLATION)  
FAN SPEED BUTTON  
MULTI-COLOR DISPLAY  
AUTO  
A/C  
DEHUM.  
FAN  
HEAT  
TIMER ON  
TIMER OFF  
FAN SPEED  
TEMPERATURE  
AND TIMER  
INDICATOR  
OSCILLATION ON/OFF  
EMERGENCY  
CONDENSATE-  
BUCKET FULL  
SLEEP MODE ON/OFF  
7
OPERATING INSTRUCTIONS  
CONTROL PANEL BUTTONS (Refer to the images on page 7)  
1) Power On and Off - Press the POW ER button once to manually turn the unit on. Press the POW ER  
button once more to turn the unit off.  
2) Mode Selection - Press the M ODE Button repeatedly to cycle between the different modes: Auto mode,  
Air Conditioner, Dehumidifier, Fan only, and Heater.  
3) Fan Speed Control - Press the FAN SPEED Button to cycle through the different fan speeds: High,  
M edium, and low. The fan speed can be visually distinguished by the speed of the digital air segments  
progressing out from the windmill fan image on the Multi-color display. There is an additional auto speed  
setting that is enabled in only heating and cooling modes. This speed is next setting after low when press-  
ing the speed control button. The speeds will cycle through in this order: Low, M edium, High, Auto. Each  
change in speed will be associated with a —beep“ sound from the unit.  
4) Temperature - Select the desired temperature by pressing either 9 or : key when using the unit in  
cooling or heating mode. The temperature indicator flashes to display the desired temperature setting. After  
the temperature is set, the unit will display this temperature setting until it is changed by the user. The  
Multi-color display shows temperature in Celsius or Fahrenheit. Press the °F/°C button on the control  
panel to select the desired temperature setting.  
5) SW ING - To turn on the exclusive W AVEFLO® oscillation, press the SW ING button on the control  
panel. Once you press SW ING, the louvers on the unit will oscillate up and down and back and forth.  
6) Timer - To program the timer, press the TIM ER ON button until the display shows a flashing —  
“.  
Press the : or 9 buttons to change the clock to the desired time for the unit to automatically turn on.  
Press the TIM ER OFF button and the display on the unit will flash —  
“. Press the : or 9  
buttons to change the clock to the desired time for the unit to automatically turn off. The TIM ER OFF  
indicator will flash for 3 seconds to activate the times you programmed.  
NOTE: The timer will also remember your settings when it is set. If you set the timer while in Air Condition-  
ing mode, the timer will automatically turn the unit on and off in air conditioning mode according to the de-  
sired programmed times. The timer will also remember the temperature settings, fan speed, and oscillation set-  
ting. The timer works when the unit is in Air Conditioner mode, Heating mode, Dehumidifier mode, Fan  
mode, and Auto mode  
OPERATING THE UNIT USING THE CONTROL PANEL  
Air Conditioner Mode  
1) Install the exhaust hoses and window kit properly (see pages 6 & 7).  
2) Plug the Power Cord into an electrical outlet.  
3) Turn on the unit by pressing the POW ER button on the control panel.  
4) Press the Mode button until the —  
“ icon appears on the Multi-color display  
5) Press the : or 9 buttons until the desired room temperature appears on the control panel  
display. The temperature ranges from 61°F - 88 °F (16 °C - 31 °C).  
8
6) Select the desired fan speed by pressing the FAN button.  
NOTE: During hot days, the unit will cool the room most efficiently by setting the temperature at the lowest  
setting and the fan speed on high. Reducing the length of the exhaust duct, insulating the exhaust hose and  
window kit, and keeping direct sunlight to a minimum will also improve the cooling efficiency.  
Dehumidifier Mode  
1) Install the exhaust hoses and window kit properly (see pages 6 & 7).  
2) Plug the Power Cord into an electrical outlet.  
3) Turn on the unit by pressing the POW ER Button on the control panel.  
4) Press the M ODE button until the —  
“ appears on the control panel display.  
NOTE: The unit operates at low fan speed during dehumidifier mode. The unit cools room slightly during  
the dehumidification. Keep the windows and doors closed to aid the effectiveness of the unit in removing the  
moisture from the room.  
NOTE: The unit will not perform in dehumidifier mode when the room temperature is lower than 61°F .  
Fan Mode  
1) Plug the Power Cord into an electrical outlet.  
2) Turn on the unit by pressing the POW ER button on the control panel.  
3) Press the M ODE button until the —  
“ icon appears on the control panel display.  
4) Select the fan speed by pressing the FAN button.  
5) To circulate more air, press the SW ING button on the remote control. The louvers will oscillate in our  
exclusive W AVEFLO® pattern; back and forth and up and down, spreading more air throughout the  
room.  
NOTE: It is not necessary for the exhaust hoses and window kit to be installed to operate the unit in fan mode.  
Heating Mode  
1) Plug the Power Cord into an electrical outlet.  
2) Turn on the unit by pressing the POW ER button on the control panel.  
3) Press the M ODE button until the —  
— icon appears on the control panel display.  
4) Press the 9or : buttons until the desired room temperature appears on the control panel display. The  
temperature ranges from 61°F - 88 °F (16 °C - 31 °C).  
5) Select the fan speed by pressing the FAN button. It is recommended to set the fan speed to low.  
Auto Mode  
1) Install the exhaust hoses and window kit properly (see pages 6 & 7).  
2) Plug the Power Cord into an electrical outlet.  
3) Turn on the unit by pressing the POW ER button on the control panel.  
4) Press the M ODE button until the —  
“ icon appears on the control panel display. Select the fan speed  
by pressing the FAN button.  
9
NOTE: During AUTO mode, the unit operates in Heating mode when the room temperature is below 68 °F,  
Dehumidifier mode when the room temperature is between 68 °F to 80 °F. And Air Conditioner mode when  
the room temperature is above 80 °F.  
Emergency Condensate Holding Tank  
W hen the room temperature is low and the indoor humidity is high, the air conditioner may not be able to  
evaporate some of the moisture fast enough. W hen this happens, the water will accumulate in an emergency  
condensate tank inside the unit. Once the emergency condensate tank is full, the unit will automatically shut  
off and the —  
“ will appear on the control panel display. To empty the condensate tank, pull the drain plug  
at the bottom back of the unit. You will need a small pan, approximately 1“ high to catch the water coming out  
of the condensate tank. Once the condensate tank is drained, the unit will begin working within a few minutes.  
The emergency condensate tank is approximately 1.5 Liters of water. Another option is to purchase a small  
hose from a hardware store that can fit around the 5/8“ drain plug on the back of the unit and drain the unit into  
a gravity drain or larger pan for continuous drainage. It is not advised to use continuous drainage when the  
room temperature is higher than 90°F .  
10  
OPERATING THE UNIT USING THE REMOTE CONTROL  
REMOTE CONTROL  
LCD DISPLAY  
MODE BUTTON  
FAN SPEED  
POW ER BUTTON  
TEMP SETTING  
TIMER ON  
SW ING (LOUVER  
OSCILLATION)  
SLEEP BUTTON  
TIMER OFF  
MINUTE SELECTER  
HOUR SELECTER  
11  
REMOTE CONTROL OPERATING INSTRUCTIONS  
1) Power On and Off - Press the POW ER (I/O) button once to manually turn the unit on. Press the Power  
button once more to turn the unit off. W hen you press the POW ER button the upper right square on the  
remote control LCD Display will light up. W hen in Air Conditioner, Heating, and Auto mode, the selected  
temperature will appear on the remote control display. W hen the unit is in Fan mode and Dehumidifier  
mode you will see the —- -“ icon instead of the set temperature. This shows that temperature selection is not  
available when the unit is in Fan or Dehumidifier mode.  
2) Mode Selection - Press the M ODE Button repeatedly to cycle between the different modes: Auto, Air  
Conditioner, Dehumidifier, Fan only, and Heater mode. The upper left square on the Remote control dis-  
play will light up showing which mode is selected. In Air Conditioner mode the display will show  
COOLING“, in Heating mode the display will show —HEAT“, in Dehumidifier mode the display will  
show —DRY“, in Fan mode the display will show —FAN“, and in Auto mode the display will show  
AUTO“.  
3) Fan Speed - Press the FAN speed button to cycle through low, medium, and high fan speeds. The dis-  
play on the remote control will show LOW , MED, & HIGH under the —SPEED“ label on the remote con-  
trol LCD display. There is an additional auto speed setting that is enabled in only heating and cooling  
modes. This speed is next setting after low when pressing the FAN speed button on the remote control.  
The speeds will cycle through in this order: High, M edium, Low, Auto. Each change in speed will be as-  
sociated with a —beep“ sound from the unit. The remote control will not display —AUTO“ under the speed  
label. Once Auto fan speed is selected the unit will beep and there will not be a fan speed displayed on the  
remote control.  
4) Temperature Setting - W hen the unit is in Air Conditioner or Heating mode you can select your desired  
temperature. Press the K or L to select your desired temperature setting. The temperature on the LCD dis-  
play on the remote control will increase or decrease accordingly. Pressing the L and K buttons simultane-  
ously will change the temperature select between °F and °C.  
5) SW ING - To turn on the exclusive W AVEFLO® oscillation, press the SW ING button on the remote  
control. Once you press SW ING, the louvers on the unit will oscillate up and down and back and forth.  
The bottom left square of the remote control display will show the —  
oscillation (SW ING) is selected.  
— icon when W AVEFLO®  
6) TIMER - To program the timer, first press the T-ON button. Once T-ON is pressed the auto-on timer will  
blink in the bottom right rectangle of the remote control display. Press the MIN and HOUR buttons to  
change the clock to the desired time for the unit to automatically turn on. The minutes will increase by 10  
with each press of the M IN button and the hours will increase by 1 with each press of the HOUR button.  
Press the T-OFF button and the remote control display will flash the desired auto-off timer. Press the MIN  
and HOUR buttons to change the clock to the desired time for the unit to automatically turn off. The timer  
is set when the auto-off time stops flashing and the words —ON“ and —OFF“ are displayed next to the time.  
7) CLOCK - To set the clock on the remote control, hold down either the M IN or HOUR button until the  
displayed time flashes on the remote control display. Change the minutes by pressing the M IN button and  
change the hours by pressing the HOUR button.  
12  
MAINTENANCE  
Note: Make sure power is off and the power cord is not plugged into an electrical outlet prior to  
performing any maintenance on the unit.  
Clean or replace filter - If the air filter is blocked with a dust, the airflow volume may reduce. It is  
recommended to clean the filter once every two weeks or as needed.  
1) Remove the filter from the filter compartment on the back of the unit.  
2) W ash the air filter by immersing it gently into warm water with a neutral detergent. Rinse the filter  
and dry it thoroughly out of sunlight.  
3) Slide the filter back into the filter compartment after it is thoroughly dried.  
4) If the filter is torn or unusable, order a new filter by calling the customer service number on the  
warranty page of this manual.  
Clean the unit Housing  
1) Keep the unit from being exposed directly to the sun to prevent color fading.  
2) Clean the surface with a damp cloth and dry it with a soft towel.  
Storing the Unit for an Extended Period of Time or Transporting the unit  
1) Empty any excess water by unplugging the water drainage stop in the back of the unit (located at  
the bottom).  
2) Unplug the unit.  
3) The unit should be stored in a cool dry place.  
DISCLAIMER  
ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER‘S MANUAL ARE THE  
PRESENTATION OF THE MANUFACTURER. SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT  
TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREW ITHIN.  
13  
WARRANTY  
One Year Limited W arranty  
Soleus International Inc. warrants the accompanying Soleus Air PE1-09R-30 Portable Air Conditioner to be free of de-  
fects in material and workmanship for the applications specified in its operation instruction for a period of ONE (1) year  
from the date of original retail purchase in the United States.  
If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of  
charge within a reasonable time after the unit is returned during the warranty period.  
As a condition to any warranty service obligation, the consumer must present this W arranty Certificate along with a  
copy of the original purchase invoice.  
THIS W ARRANTY DOES NOT COVER:  
ñ
Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in  
material or workmanship.  
ñ
Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions  
in the instructions.  
ñ
ñ
Damage to the finish of the case, or other appearance parts caused by wear.  
Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus Interna-  
tional Inc.  
ñ
Freight and Insurance cost for the warranty service.  
ALL W ARRANTIES, INCLUDING ANY IMPLIED W ARRANTY OF MERCHANT ABILITY ARE LIMITED TO  
ONE-YEAR DURATION OF THIS EXPRESS LIMITED W ARRANTY. SOLEUS INTERNATIONAL INC.  
DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT  
SHALL SOLEUS INTERNATIONAL INC‘S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR  
BREACH OF ANY W RITTEN OR IMPLIED W ARRANTY W ITH RESPECT TO THIS UNIT.  
This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, sal-  
vaged, or refurbished products.  
As some states do not allow the limitation or exclusion of incidental or consequential damages, or do not allow  
limitation on implied warranties, the above limitations and exclusions may not apply to you. This warranty gives you  
specific legal rights, and you may also have other rights that vary from state to state.  
For W arranty, Technical Support, Customer Service, M issing or Defective Parts  
Please Call (888) 876-5387  
Or W rite To:  
Soleus International Inc.  
9451 Telstar Ave.  
El Monte, CA 91731 USA  
14  

Tru Test 1 J User Manual
Trane Air Conditioner Tcont800as11aa User Manual
Toshiba Barcode Reader B Sv4d Gs User Manual
Tekkeon Healthy White Hx6730 User Manual
Studer Innotec C 1600 12 C 2600 24 C 4000 48 User Manual
Simplicity Sac8017ee User Manual
Samsung Aw1209b User Manual
CRAFTSMAN 138.98982 User Manual
BOSCH 3000 FRE User Manual
ASUS Y482M User Manual