Sharp All In One Printer Mx B400p User Manual

MX-B400P  
MODEL:  
LASER PRINTER  
Software Setup Guide  
BEFORE INSTALLING  
THE SOFTWARE  
SETUP IN A WINDOWS  
ENVIRONMENT  
SETUP IN A MACINTOSH  
ENVIRONMENT  
TROUBLESHOOTING  
Keep this manual close at hand for reference  
whenever needed.  
TABLE OF CONTENTS  
BEFORE INSTALLING THE SOFTWARE  
1
CD-ROMS AND SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
• SOFTWARE CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
VERIFYING SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
• SYSTEM REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
• SOFTWARE REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
CONNECTING THE MACHINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
• CONNECTING TO A NETWORK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
• CONNECTING THE MACHINE WITH A USB CABLE (Windows). . . . . . . . . . . . . . 6  
SETUP IN A WINDOWS ENVIRONMENT  
2
OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE) . . . . . . 7  
INSTALLING THE PRINTER DRIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
• WHEN THE MACHINE IS CONNECTED TO A NETWORK . . . . . . . . . . . . . . . . . . 9  
• WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE. . . . . . . . . 21  
• USING THE MACHINE AS A SHARED PRINTER . . . . . . . . . . . . . . . . . . . . . . . . 29  
• USING THE STANDARD WINDOWS PS PRINTER DRIVER (Windows  
98/Me/NT 4.0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
• CONFIGURING THE PRINTER DRIVER FOR THE OPTIONS INSTALLED  
ON THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
INSTALLING THE PRINTER STATUS MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
CHANGING THE PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
SETUP IN A MACINTOSH ENVIRONMENT  
3
MAC OS X. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
MAC OS 9.0 - 9.2.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
TROUBLESHOOTING  
4
WHEN INSTALLATION WAS NOT SUCCESSFUL . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
REMOVING THE SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
1
BEFORE INSTALLING THE  
SOFTWARE  
This chapter describes the software programs that allow you to use the printer  
function of the machine, the CD-ROMs that contain the software, and the pages  
where the installation procedures can be found.  
1
CD-ROMS AND SOFTWARE  
The software that can be used with the machine is on the CD-ROMs that  
accompany the machine.  
Before installing the software, make sure that your computer and the machine  
meet the system requirements described in "VERIFYING SYSTEM  
REQUIREMENTS" (page 4).  
SOFTWARE CD-ROM  
The "Software CD-ROM" that accompanies the machine contains the printer  
driver and other software. The "Software CD-ROM" consists of 2 discs.  
For users of Windows 98/Me/NT 4.0  
The CD-ROM does not include software for Windows 98/Me/NT 4.0.  
Contact your dealer or nearest SHARP Service Department if you want software  
for Windows 98/Me/NT 4.0.  
Disc 1  
Software for Windows  
Printer driver  
These allow the machine to be used as a printer.  
- PCL6 and PCL5e printer driver  
The machine supports the Hewlett-Packard PCL6 and PCL5e printer  
control languages. It is recommended that you use the PCL6 printer driver.  
If you have a problem printing from older software using the PCL6 printer  
driver, use the PCL5e printer driver.  
- PS printer driver  
The PS printer driver supports the PostScript 3 page description language  
developed by Adobe Systems Incorporated.  
2
CD-ROMS AND SOFTWARE  
- PPD driver  
The PPD driver enables the machine to use the standard Windows PS  
printer driver.  
WHEN THE MACHINE IS CONNECTED TO A NETWORK (page 9)  
WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE  
(page 21)  
Printer Status Monitor (can only be used when the machine is  
connected to a network)  
This allows you to monitor the status of the machine on your computer screen.  
INSTALLING THE PRINTER STATUS MONITOR (page 38)  
Disc 2  
Software for Windows  
Printer Administration Utility (can only be used when the machine is  
connected to a network)  
This allows the administrator to monitor the machine and configure machine  
settings from a computer. To install and use the Printer Administration Utility,  
see the Readme file and the manual in PDF format on the "Software  
CD-ROM" (Disc 2). The Readme file and manual are in the following folder on  
the CD-ROM. (Substitute the letter of your CD-ROM drive for "R" in the  
following path.)  
R:\Sadmin\Documents\EnglishA  
Software for Macintosh  
PPD file  
This is the printer description file which enables the machine to be used as a  
PostScript 3 compatible printer.  
MAC OS X (page 43)  
MAC OS 9.0 - 9.2.2 (page 52)  
To use the machine as a printer in a Macintosh environment, the machine  
must be connected to a network. A USB connection cannot be used.  
3
VERIFYING SYSTEM REQUIREMENTS  
SYSTEM REQUIREMENTS  
Before installing the software described in this manual, make sure that your  
computer satisfies the following requirements.  
5
Windows  
Macintosh*  
Operating  
system  
Windows 98, Windows Me,  
Mac OS 9.0 to 9.2.2,  
*1  
Windows NT Workstation 4.0 (Service Pack 5 Mac OS X v10.2.8,  
2
or later)* , Windows 2000 Professional,  
Mac OS X v10.3.9,  
Windows XP Professional, Windows XP Home Mac OS X v10.4.11,  
Edition, Windows 2000 Server,  
Windows Server 2003, Windows Vista,  
Windows Server 2008, Windows 7  
Mac OS X v10.5 to  
10.5.8,  
Mac OS X v10.6  
Computer type IBM PC/AT compatible computer  
Equipped with a  
An environment in  
which any of the  
10Base-T/100Base-TX/1000Base-T LAN operating systems listed  
board or equipped standard with a USB  
2.0 /1.1 port.  
above can fully operate  
(including Macintosh  
computers with an Intel  
processor).  
*3  
*4  
Display  
1024 x 768 dots resolution and 16-bit  
color or higher is recommended.  
Other hardware  
requirements  
An environment that allows any of the above  
operating systems to fully operate.  
*1 Printing is not possible in MS-DOS mode.  
*2 USB is not supported.  
*3 The machine's USB 2.0 port will transfer data at the speed specified by the USB 2.0  
(Hi-Speed) standard only if the Microsoft USB 2.0 driver is preinstalled in the  
computer, or if the USB 2.0 driver for Windows 2000 Professional/XP/Vista/7 that  
Microsoft provides through "Windows Update" is installed.  
*4 Compatible with models preinstalled with Windows 98, Windows Me, Windows 2000  
Professional, Windows XP Professional, Windows XP Home Edition, Windows 2000  
Server, Windows Server 2003, Windows Vista, Windows Server 2008, or Windows 7  
and which are equipped standard with a USB interface.  
*5 Cannot be used when the machine is connected with a USB cable.  
For users of Windows 98/Me/NT 4.0  
The CD-ROM does not include software for Windows 98/Me/NT 4.0.  
Contact your dealer or nearest SHARP Service Department if you want software for  
Windows 98/Me/NT 4.0.  
For users of Windows NT 4.0/2000/XP/Server 2003/Vista/Server 2008/7  
To perform the procedures described in this manual such as installing the software  
and configuring settings after installation, administrator authority is required.  
4
VERIFYING SYSTEM REQUIREMENTS  
SOFTWARE REQUIREMENTS  
The following requirements must be met to use the software described in this  
manual.  
Operating system  
Software  
Type of connection*  
environment*  
Windows  
PCL6 printer driver,  
PCL5e printer driver  
Network/ USB  
PS printer driver,  
PPD driver  
Printer Status Monitor  
Printer Administration Utility  
Macintosh PPD file  
Network only (cannot be  
used with a USB  
connection)  
Macintosh  
* For the types of computers and operating systems that can run the software,  
see "SYSTEM REQUIREMENTS" (page 4).  
5
CONNECTING THE MACHINE  
CONNECTING TO A NETWORK  
To connect the machine to a network, connect the LAN cable to the machine's  
network connector. Use a shielded LAN cable.  
After connecting the machine to a network, be sure to configure the IP address  
and other network settings before installing the software. (The factory default  
setting for the IP address is to receive the IP address automatically when the  
machine is used in a DHCP environment.)  
Network settings can be configured using "Network Settings" in the system  
settings (administrator) on the machine.  
If the machine is used in a DHCP environment, the IP address of the machine may  
change. If this happens, printing will not be possible. This problem can be avoided by  
using a WINS server or by assigning a permanent IP address to the machine.  
• This manual explains how to set up the software in a Windows network  
environment and in a Macintosh network environment.  
X Checking the IP address of the machine  
You can check the IP address by pressing the [SYSTEM SETTINGS] key on the  
machine and printing out the "All Custom Setting List" from [List Print (User)].  
CONNECTING THE MACHINE WITH A USB  
CABLE (Windows)  
The machine can be connected to a computer using a USB cable if the  
computer is a Windows computer. (The USB interface on the machine cannot  
be used in a Macintosh environment.)  
The machine and computer should be connected while the printer driver is  
being installed. If a USB cable is connected before the printer driver is installed,  
the printer driver will not be installed correctly. For the procedure for connecting  
a USB cable, see "WHEN THE MACHINE WILL BE CONNECTED WITH A  
USB CABLE" (page 21).  
6
SETUP IN A WINDOWS ENVIRONMENT  
2
This section explains how to install the software and configure settings so that  
the printer function of the machine can be used with a Windows computer.  
For users of Windows 98/Me/NT 4.0  
The CD-ROM does not include software for Windows 98/Me/NT 4.0.  
Contact your dealer or nearest SHARP Service Department if you want software  
for Windows 98/Me/NT 4.0.  
OPENING THE SOFTWARE SELECTION  
SCREEN (FOR ALL SOFTWARE)  
Insert the "Software CD-ROM" into your computer's CD-ROM drive.  
Insert the "Software CD-ROM" that shows "Disc 1" on the front of the CD-ROM.  
1
Click the [Start] button ( ), click [Computer], and then double-click  
the [CD-ROM] icon ( ).  
• In Windows XP/Server 2003, click the [start] button, click [My Computer], and  
then double-click the [CD-ROM] icon.  
2
• In Windows 2000, double-click [My Computer] and then double-click the  
[CD-ROM] icon.  
Double-click the [Setup] icon ( ).  
3
• In Windows 7, if a message screen appears asking you for confirmation, click  
[Yes].  
• In Windows Vista/Server 2008, if a message screen appears asking you for  
confirmation, click [Allow].  
7
OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)  
The "SOFTWARE LICENSE" window will appear. Make sure that you  
understand the contents of the license agreement and then click the  
[Yes] button.  
4
You can show the "SOFTWARE LICENSE" in a different language by selecting  
the desired language from the language menu. To install the software in the  
selected language, continue the installation with that language selected.  
Read the message in the "Welcome" window and then click the [Next]  
button.  
5
The software selection screen appears.  
Before installing the software, be sure to click the [Display Readme] button and  
view the detailed information on the software.  
6
For the steps that follow, see the appropriate page below for the software that  
you are installing.  
INSTALLING THE PRINTER DRIVER  
WHEN THE MACHINE IS CONNECTED TO A NETWORK  
- Standard installation: page 10  
- Installation by specifying the machine's address: page 14  
- Printing using the IPP function and the SSL function: page 18  
WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE: page 21  
USING THE MACHINE AS A SHARED PRINTER: page 29  
INSTALLING THE PRINTER STATUS MONITOR: page 38  
8
INSTALLING THE PRINTER  
DRIVER  
To install the printer driver, follow the appropriate procedure in this section  
depending on whether the machine is connected to a network or connected by  
USB cable.  
WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE (page 21)  
WHEN THE MACHINE IS CONNECTED TO A  
NETWORK  
This section explains how to install the printer driver when the machine is  
connected to a Windows network (TCP/IP network).  
*
*
*
Supported operating systems: Windows 98/Me/NT 4.0 /2000 /XP /  
*
*
*
*
Server 2003 /Vista /Server 2008 /7  
* Administrator's rights are required to install the software.  
To install the PPD driver when Windows 98/Me/NT 4.0 is used, see "USING  
THE STANDARD WINDOWS PS PRINTER DRIVER (Windows 98/Me/NT 4.0)"  
(page 32) and install the driver using the Add Printer Wizard.  
• To use the machine as a network printer in Windows NT 4.0, "TCP/IP  
Protocol" must be installed on your computer. If this is not installed, see  
Windows NT 4.0 Help to install "TCP/IP Protocol".  
To print to the machine over the Internet using the IPP function when  
the machine is installed in a remote location, or to print using the SSL  
(encrypted communication) function, see "Printing using the IPP  
function and the SSL function" (page 18) and install the printer driver.  
If the machine is connected to an IPv6-only network, the software  
cannot be installed by detecting or specifying the machine's address  
from the installer.  
9
INSTALLING THE PRINTER DRIVER  
X Standard installation  
When the software selection screen appears in step 6 of "OPENING THE  
SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7),  
perform the steps below.  
Click the [Printer Driver]  
button.  
1
Click the [Standard installation] button.  
2
When [Custom installation] is selected, you can change any of the items below.  
When [Standard installation] is selected, the installation will take place as  
indicated below.  
10  
INSTALLING THE PRINTER DRIVER  
• Machine connection method: LPR Direct Print (Auto Search)  
• Set as default printer: Yes  
• Printer driver name: Cannot be changed  
• Display fonts: Installed  
If you selected [Custom installation], select [LPR Direct Print (Auto Search)] and  
click the [Next] button.  
If you selected other than [LPR Direct Print (Auto Search)], see the following  
pages:  
• LPR Direct Print (Specify Address): page 14  
• IPP: page 18  
• Shared printer: page 29  
• Connected to this computer: page 21  
Printers connected to the  
network are detected.  
Select the machine and  
click the [Next] button.  
3
• If the machine is not found, make sure that the machine is powered on and  
that the machine is connected to the network, and then click the [Re-search]  
button.  
• You can also click the [Specify condition] button and search for the machine  
by entering the machine's name (host name) or IP address.  
Checking the IP address of the machine (page 6)  
A confirmation window appears. Check the contents and then click  
the [Next] button.  
4
11  
INSTALLING THE PRINTER DRIVER  
When the printer driver  
5
selection window appears,  
select the printer driver to  
be installed and click the  
[Next] button.  
Click the checkbox of the printer  
driver to be installed so that a  
checkmark (  
) appears.  
The [PPD] checkbox only appears if you are using Windows 2000/XP/  
Server 2003/Vista/Server 2008/7.  
When you are asked whether or not you want the printer to be your  
default printer, make a selection and click the [Next] button.  
If you are installing multiple drivers, select the printer driver to be used as the  
default printer.  
6
If you do not wish to set one of the printer drivers as the default printer, select [No].  
If you clicked the [Custom installation] button in step 2, the following windows  
will appear.  
Printer name window  
If you wish to change the printer name, enter the desired name and click the  
[Next] button.  
Window confirming installation of the display fonts  
To install the display fonts, select [Yes] and click the [Next] button.  
12  
INSTALLING THE PRINTER DRIVER  
Follow the on-screen instructions.  
Read the message in the window that appears and click the [Next] button.  
Installation begins.  
7
If you are using Windows Vista/Server 2008/7  
If a security warning window appears, be sure to click [Install this driver  
software anyway].  
If you are using Windows 2000/XP/Server 2003  
If a warning message regarding the Windows logo test or digital signature  
appears, be sure to click the [Continue Anyway] or [Yes] button.  
When the installation completed screen appears, click the [OK]  
button.  
8
9
Click the [Close] button in the window of step 1.  
After the installation, a message prompting you to restart your computer may  
appear. If this message appears, click the [Yes] button to restart your computer.  
This completes the installation.  
• After installation, see "CONFIGURING THE PRINTER DRIVER FOR THE  
OPTIONS INSTALLED ON THE MACHINE" (page 34) to configure the printer  
driver settings.  
• If you are using the machine as a shared printer, see "USING THE MACHINE  
AS A SHARED PRINTER" (page 29) to install the printer driver on each of the  
client computers.  
13  
INSTALLING THE PRINTER DRIVER  
X
Installation by specifying the machine's address  
When the machine cannot be found because it is not powered on or otherwise,  
installation is possible by entering the name (host name) or IP address of the machine.  
When the software selection screen appears in step 6 of "OPENING THE  
SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7),  
perform the steps below.  
Click the [Printer Driver] button.  
1
Click the [Custom installation] button.  
2
14  
INSTALLING THE PRINTER DRIVER  
When you are asked how the printer is connected, select [LPR Direct  
Print (Specify Address)] and click the [Next] button.  
3
4
Enter the name (host name) or IP address of the machine and click  
the [Next] button.  
Checking the IP address of the machine (page 6)  
When the model selection window appears, select the model name of  
your machine and click the [Next] button.  
5
15  
INSTALLING THE PRINTER DRIVER  
When the printer driver selection window appears, select the printer  
driver to be installed and click the [Next] button.  
6
Click the checkbox of the printer driver to be installed so that a checkmark (  
)
appears.  
The [PPD] checkbox only appears if you are using Windows 2000/XP/  
Server 2003/Vista/Server 2008/7.  
Select whether or not you wish the printer to be your default printer  
and click the [Next] button.  
If you are installing multiple drivers, select the printer driver to be used as the  
7
default printer.  
If you do not wish to set one of the printer drivers as the default printer, select [No].  
When the printer name window appears, click the [Next] button.  
If you wish to change the printer name, enter the desired name and click the [Next]  
button.  
8
9
When you are asked if you wish to install the display fonts, select an  
answer and click the [Next] button.  
16  
INSTALLING THE PRINTER DRIVER  
Follow the on-screen instructions.  
Read the message in the window that appears and click the [Next] button.  
Installation begins.  
10  
If you are using Windows Vista/Server 2008/7  
If a security warning window appears, be sure to click [Install this driver  
software anyway].  
If you are using Windows 2000/XP/Server 2003  
If a warning message regarding the Windows logo test or digital signature  
appears, be sure to click the [Continue Anyway] or [Yes] button.  
When the installation completed screen appears, click the [OK]  
button.  
11  
12  
Click the [Close] button in the window of step 1.  
After the installation, a message prompting you to restart your computer may  
appear. If this message appears, click the [Yes] button to restart your computer.  
This completes the installation.  
After installation, see "CONFIGURING THE PRINTER DRIVER FOR THE  
OPTIONS INSTALLED ON THE MACHINE" (page 34) to configure the printer  
driver settings.  
17  
INSTALLING THE PRINTER DRIVER  
X Printing using the IPP function and the SSL  
function  
The IPP function can be used to print to the machine over a network using  
HTTP protocol.  
The IPP function can also be used in combination with the SSL (encrypted  
communication) function to encrypt the print data. This enables secure printing  
with no concern that the data will be leaked to others.  
To use the SSL function, configure the "SSL Settings" in the system settings  
(administrator) of the machine. To configure the settings, see the "SYSTEM  
SETTINGS" chapter in the Operation Guide.  
When the software selection screen appears in step 6 of "OPENING THE  
SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7),  
perform the steps below.  
Click the [Printer Driver] button.  
1
18  
INSTALLING THE PRINTER DRIVER  
Click the [Custom installation] button.  
2
3
When you are asked how the printer is connected, select [IPP] and  
click the [Next] button.  
If a proxy server is used, specify the proxy server and click the [Next] button.  
To specify a proxy server, select [Print via the proxy server] and then enter the  
[Address] and [Port number].  
4
19  
INSTALLING THE PRINTER DRIVER  
Enter the machine's URL and click the [Next] button.  
Enter the URL in the following format:  
5
Normal format:  
1
*1 Normally "631" should be entered for the port number. If the IPP port number  
has been changed on the machine, enter the new port number.  
When SSL is used:  
2
*2 Normally the port number and the colon ":" immediately preceding the port  
number can be omitted. If the IPP port number for SSL has been changed on  
the machine, enter the new port number.  
If your computer and the machine are connected to the same local area  
network, you can click the [Search] button to search for the machine. The  
machine's URL will appear. Select the URL and click the [OK] button. You will  
return to the above screen and the machine's URL will be automatically entered.  
Perform steps 5 through 12 on page 15 to continue the installation.  
6
This completes the installation.  
After installation, see "CONFIGURING THE PRINTER DRIVER FOR THE  
OPTIONS INSTALLED ON THE MACHINE" (page 34) to configure the printer  
driver settings.  
20  
INSTALLING THE PRINTER DRIVER  
WHEN THE MACHINE WILL BE  
CONNECTED WITH A USB CABLE  
*
*
*
Supported operating systems: Windows 98/Me/2000 /XP /Server 2003 /  
*
*
*
Vista /Server 2008 /7  
* Administrator's rights are required to install the software.  
Make sure that a USB cable is not connected to your computer and the  
machine.  
If a cable is connected, a Plug and Play window will appear. If this happens,  
click the [Cancel] button to close the window and disconnect the cable.  
• To install the PPD driver when Windows 98/Me is used, see "USING THE  
STANDARD WINDOWS PS PRINTER DRIVER (Windows 98/Me/NT 4.0)"  
(page 32) and install the driver using the Add Printer Wizard.  
When the software selection screen appears in step 6 of "OPENING THE  
SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7),  
perform the steps below.  
Click the [Printer Driver] button.  
1
21  
INSTALLING THE PRINTER DRIVER  
Click the [Custom installation] button.  
2
When you are asked how the printer is connected, select [Connected  
to this computer] and click the [Next] button.  
3
When you are asked if you wish to install the display fonts, select an  
answer and click the [Next] button.  
4
22  
INSTALLING THE PRINTER DRIVER  
Follow the on-screen instructions.  
Read the message in the window that appears and click the [Next] button.  
When the installation completed screen appears, click the [OK] button.  
5
If you are using Windows Vista/Server 2008/7  
If a security warning window appears, be sure to click [Install this driver  
software anyway].  
If you are using Windows 2000/XP/Server 2003  
If a warning message regarding the Windows logo test or digital signature  
appears, be sure to click the [Continue Anyway] or [Yes] button.  
Click the [Close] button in the window of step 1.  
When a message appears prompting you to connect the machine to your  
computer, click the [OK] button.  
6
7
After the installation, a message prompting you to restart your computer may  
appear. If this message appears, click the [Yes] button to restart your computer.  
Connect the machine to your  
computer with a USB cable.  
(1) Make sure that the  
machine is powered on.  
(2) Connect the cable to the  
USB connector (B type) on  
the machine.  
The USB interface on the  
machine complies with the USB  
2.0 (Hi-Speed) standard. Please  
purchase a shielded USB cable.  
(3) Connect the other end of the cable to the USB connector (A type)  
on your computer.  
The machine is found and a Plug and Play window appears.  
23  
INSTALLING THE PRINTER DRIVER  
Installation of the PCL6 printer driver begins.  
8
When the "Found New Hardware Wizard" appears, select [Install the software  
automatically (Recommended)], click the [Next] button, and follow the on-screen  
instructions.  
If you are using Windows Vista/Server 2008/7  
If a security warning window appears, be sure to click [Install this driver  
software anyway].  
If you are using Windows 2000/XP/Server 2003  
If a warning message regarding the Windows logo test or digital signature  
appears, be sure to click the [Continue Anyway] or [Yes] button.  
This completes the installation.  
• After installing the printer driver, see "CONFIGURING THE PRINTER  
DRIVER FOR THE OPTIONS INSTALLED ON THE MACHINE" (page 34) to  
configure the printer driver settings.  
• If you are using the machine as a shared printer, see "USING THE MACHINE  
AS A SHARED PRINTER" (page 29) to install the printer driver on each of the  
client computers.  
24  
INSTALLING THE PRINTER DRIVER  
When installing the PCL5e printer driver, PS printer driver, or PPD driver  
Installation is possible even after the USB cable has been connected. When the  
software selection screen appears in step 6 of "OPENING THE SOFTWARE  
SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7), perform the steps  
below.  
Click the [Printer Driver] button.  
1
Click the [Custom installation] button.  
2
25  
INSTALLING THE PRINTER DRIVER  
When you are asked how the printer is connected, select [Connected  
to this computer] and click the [Next] button.  
3
When the port selection window appears, select the port that the  
PCL6 printer driver is using (USB001, etc.) and click the [Next]  
button.  
4
When the printer driver selection window appears, remove the [PCL6]  
checkmark and select the printer driver to be installed, and then click  
the [Next] button.  
5
Click the checkbox of the printer driver to be installed so that a checkmark (  
)
appears.  
The [PPD] checkbox only appears if you are using Windows 2000/XP/  
Server 2003/Vista/Server 2008/7.  
26  
INSTALLING THE PRINTER DRIVER  
Select whether or not you wish the printer to be your default printer  
and click the [Next] button.  
If you are installing multiple drivers, select the printer driver to be used as the  
6
7
default printer.  
If you do not wish to set one of the printer drivers as the default printer, select [No].  
When the printer name window appears, click the [Next] button.  
If you wish to change the printer name, enter the desired name and click the [Next]  
button.  
When you are asked if you wish to install the display fonts, select  
[No] and click the [Next] button.  
8
9
Follow the on-screen instructions.  
Read the message in the window that appears and click the [Next] button.  
Installation begins.  
If you are using Windows Vista/Server 2008/7  
If a security warning window appears, be sure to click [Install this driver  
software anyway].  
If you are using Windows 2000/XP/Server 2003  
If a warning message regarding the Windows logo test or digital signature  
appears, be sure to click the [Continue Anyway] or [Yes] button.  
When the installation completed screen appears, click the [OK]  
button.  
10  
11  
Click the [Close] button in the window of step 1.  
After the installation, a message prompting you to restart your computer may  
appear. If this message appears, click the [Yes] button to restart your computer.  
27  
INSTALLING THE PRINTER DRIVER  
This completes the installation.  
• After installation, see "CONFIGURING THE PRINTER DRIVER FOR THE  
OPTIONS INSTALLED ON THE MACHINE" (page 34) to configure the printer  
driver settings.  
• Make sure that the port of the installed driver is the same as the port used by  
the PCL6 printer driver.  
The port used by the printer driver of the machine is indicated by a checkmark  
on the [Ports] tab of the printer driver properties window. (In Windows 98/Me,  
this is the port selected in [Print to the following port] on the [Details] tab.)  
CHANGING THE PORT (page 40)  
28  
INSTALLING THE PRINTER DRIVER  
USING THE MACHINE AS A SHARED PRINTER  
If you are going to use the machine as a shared printer on a Windows network with  
the printer driver installed on a print server, follow the steps below to install the  
printer driver on the client computers.  
• Ask your network administrator for the server name and printer name of the  
machine on the network.  
• For the procedure for configuring settings on the print server, see the  
operation manual or the Help file of the operating system. The "print server"  
explained here is a computer that is connected directly to the machine, and  
"clients" are other computers connected to the same network as the print  
server.  
• Install the same printer driver on client computers as the printer driver that is  
installed on the print server.  
• If the PPD driver is installed on the print server and the client computers are  
running Windows 98/Me/NT 4.0, see "USING THE STANDARD WINDOWS  
PS PRINTER DRIVER (Windows 98/Me/NT 4.0)" (page 32) to install the  
printer driver using the Add Printer Wizard.  
When the software selection screen appears in step 6 of "OPENING THE  
SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7),  
perform the steps below.  
29  
INSTALLING THE PRINTER DRIVER  
Click the [Printer Driver] button.  
1
Click the [Custom installation] button.  
2
Select [Shared Printer] and click the [Next] button.  
3
30  
INSTALLING THE PRINTER DRIVER  
Select the printer name (configured as a shared printer).  
4
(1)  
(2)  
(1) Select the printer name (configured as a shared printer on a print  
server) from the list.  
If you are using Windows 98/Me/NT 4.0/2000/XP/Server 2003, you can also  
click the [Add Network Port] button displayed below the list and select the  
printer to be shared by browsing the network in the window that appears.  
(2) Click the [Next] button.  
If the shared printer does not appear in the list, check the settings on the print  
server.  
Perform steps 5 through 12 on page 15 to continue the installation.  
In the printer driver selection screen, be sure to select the same type of printer  
driver as the printer driver installed on the print server.  
5
This completes the installation.  
31  
INSTALLING THE PRINTER DRIVER  
USING THE STANDARD WINDOWS PS  
PRINTER DRIVER (Windows 98/Me/NT 4.0)  
If you wish to use the standard Windows 98/Me/NT 4.0 PS printer driver, follow  
the steps below to install the PPD driver using the Add Printer Wizard.  
• The CD-ROM does not include software for Windows 98/Me/NT 4.0.  
Contact your dealer or nearest SHARP Service Department if you want  
software for Windows 98/Me/NT 4.0.  
• If you are using Windows 2000/XP/Server 2003/Vista/Server 2008/7, you can  
install the PPD driver from the installer.  
• Be sure to view the Readme file (Readme.txt) before installing the PPD driver.  
The Readme file will be in the [EnglishA] folder inside the folder that contains  
the extracted files after you get the software.  
Download the software and save the extracted files in any folder.  
1
Click the [Start] button, select [Settings] and then click [Printers].  
2
Double-click the [Add printer] icon.  
The "Add Printer Wizard" will appear.  
3
Follow the on-screen instructions.  
When you are asked to specify the path of the PPD file, enter the path as follows.  
4
Operating system  
Windows 98/Me  
PPD file path  
(Folder containing extracted files)\EnglishA\PPD\9XME  
(Folder containing extracted files)\EnglishA\PPD\NT40  
Windows NT 4.0  
After installation, see "CONFIGURING THE PRINTER DRIVER FOR THE  
OPTIONS INSTALLED ON THE MACHINE" (page 34) to configure the printer  
driver settings.  
32  
INSTALLING THE PRINTER DRIVER  
X Installing the resident font information  
(Windows 98/Me)  
If you have installed the PPD driver on Windows 98/Me and will be using the  
resident fonts in the machine, you must install the resident font information.  
Follow the procedure below to install the resident font information.  
• Before installing the resident font information, be sure to install the PPD  
driver.  
• In the event that a resident font cannot be selected in a software application,  
install the resident font information again.  
Double-click the folder where the extracted files are saved when you  
installed the PPD driver.  
1
Double-click the [EnglishA] folder, the [PPD] folder, the [9XME]  
folder, and then [PFMSetup.exe].  
2
Follow the on-screen instructions.  
After the resident font information has been installed, restart your computer.  
3
33  
INSTALLING THE PRINTER DRIVER  
CONFIGURING THE PRINTER DRIVER FOR  
THE OPTIONS INSTALLED ON THE MACHINE  
After installing the printer driver, you must configure the printer driver settings  
appropriately for the options that have been installed and the size and type of  
paper loaded in the machine. Follow the steps below to configure the printer  
driver.  
If the PPD driver is installed, see "When the PPD driver is installed" (page 37).  
X When the PCL printer driver or PS printer  
driver is installed  
Click the [Start] button ( ), click [Control Panel], and then click  
[Printer].  
• In Windows 7, click the [Start] button and then click [Devices and Printers].  
1
• In Windows XP/Server 2003, click the [start] button and then click [Printers and  
Faxes].  
• In Windows 98/Me/NT 4.0/2000, click the [Start] button, select [Settings], and  
then click [Printers].  
If [Printers and Faxes] does not appear in the [start] menu in Windows XP, click  
the [start] button, click [Control Panel], click [Printers and Other Hardware], and  
then click [Printers and Faxes].  
Open the printer properties window.  
(1) Right-click the printer driver icon of the machine.  
2
(2) Select [Properties].  
In Windows 7, select [Printer Properties].  
Click the [Configuration] tab.  
In Windows 98/Me, click the [Setup] tab and then click the [Configuration] tab in the  
window that appears.  
3
34  
INSTALLING THE PRINTER DRIVER  
Click the [Auto Configuration] button.  
The settings are automatically configured based on the detected machine status.  
4
5
*The screen shows the PCL6 printer driver.  
Configure the image of the machine.  
An image of the machine is formed in the printer driver configuration window based  
on the options that are installed.  
(1)  
(2)  
(1) Select the options that are installed on the machine.  
(2) Click the [OK] button.  
To cancel the image settings, click the [Cancel] button.  
35  
INSTALLING THE PRINTER DRIVER  
Click the [OK] button in the printer properties window.  
6
If automatic configuration fails, configure the settings manually.  
• You can check the options that are installed and the tray settings by printing  
out the "All Custom Setting List" in the system settings of the machine.  
(However, note that "Input Tray Options" must be set to the number of trays  
on the machine.) The "All Custom Settings List" can be printed from [List Print  
(User)] in the system settings.  
• Click the [Set Tray Status] button and the [Paper Type Name] button to check  
the settings of each.  
Set Tray Status:  
The "Tray Settings" in "Paper Tray Settings" in system  
settings of the machine are reflected in the settings  
shown here. Specify the size and type of paper loaded in  
each tray.  
Paper Type Name: The "Paper Type Registration" settings in "Paper Tray  
Settings" in the system settings of the machine are  
reflected in the settings shown here. If a user type name  
(1 to 7) was changed, enter the changed name.  
36  
INSTALLING THE PRINTER DRIVER  
X When the PPD driver is installed  
Click the [Start] button ( ), click [Control Panel], and then click  
[Printer].  
• In Windows 7, click the [Start] button and then click [Devices and Printers].  
1
• In Windows XP/Server 2003, click the [start] button and then click [Printers and  
Faxes].  
• In Windows 98/Me/NT 4.0/2000, click the [Start] button, select [Settings], and  
then click [Printers].  
If [Printers and Faxes] does not appear in the [start] menu in Windows XP, click  
the [start] button, click [Control Panel], click [Printers and Other Hardware], and  
then click [Printers and Faxes].  
Open the printer properties window.  
(1) Right-click the printer driver icon of the machine.  
(2) Select [Properties].  
2
3
In Windows 7, select [Printer Properties].  
Configure the printer driver for the options installed on the machine.  
(1) Click the [Device Settings] tab.  
In Windows 98/Me, click the [Device Options] tab.  
(2) Configure each item based on the machine configuration.  
The items and the procedures for configuring the items vary depending on the  
operating system version.  
(3) Click the [OK] button.  
You can check the options that are installed on the machine by printing out the  
"All Custom Setting List" in the system settings. (However, note that "Input Tray  
Options" must be set to the number of trays on the machine.) The "All Custom  
Settings List" can be printed from [List Print (User)] in the system settings.  
37  
INSTALLING THE PRINTER  
STATUS MONITOR  
Printer Status Monitor is a printer utility that allows general users to check the  
current status of the machine on their computer screen, such as whether or not  
the machine is ready to print. The Printer Status Monitor shows error  
information such as paper misfeeds, printer configuration information (whether  
or not a finisher is installed, etc.) as an image, the paper sizes that can be used,  
and the amount of paper remaining.  
The Printer Status Monitor cannot be used in the following situations:  
• When the machine is connected by a USB cable.  
• When printing to the machine using the IPP function.  
*
*
*
Supported operating systems: Windows 98/Me/NT 4.0 /2000 /XP /  
Server 2003 /Vista /Server 2008 /7  
*
*
*
*
* Administrator's rights are required to install the software.  
When the software selection screen appears in step 6 of "OPENING THE  
SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 7),  
perform the steps below.  
Click the [Printer Status Monitor] button.  
1
38  
INSTALLING THE PRINTER STATUS MONITOR  
Follow the on-screen instructions.  
2
3
When the installation completed screen appears, click the [Finish]  
button.  
To have the Printer Status Monitor start automatically when your computer is  
started, select the [Add this program to your Startup folder] checkbox  
the [Finish] button.  
and click  
Click the [Close] button in the window of step 1.  
4
After the installation, a message prompting you to restart your computer may  
appear. If this message appears, click the [Yes] button to restart your computer.  
This completes the installation.  
For the procedures for using the Printer Status Monitor, see the Help file. Follow  
these steps to view the Help file:  
Click the Windows [start] button, select [All Programs] ([Programs] in Windows  
98/Me/NT 4.0/2000), select [SHARP Printer Status Monitor] and then select  
[Help].  
39  
CHANGING THE PORT  
When using the machine in a Windows environment, follow the steps below to  
change the port when you have changed the IP address of the machine when  
the machine is connected with a USB cable.  
Click the [Start] button ( ), click [Control Panel], and then click  
[Printer].  
• In Windows 7, click the [Start] button and then click [Devices and Printers].  
1
• In Windows XP/Server 2003, click the [start] button and then click [Printers and  
Faxes].  
• In Windows 98/Me/NT 4.0/2000, click the [Start] button, select [Settings], and  
then click [Printers].  
If [Printers and Faxes] does not appear in the [start] menu in Windows XP, click  
the [start] button, click [Control Panel], click [Printers and Other Hardware], and  
then click [Printers and Faxes].  
Open the printer properties window.  
(1) Right-click the printer driver icon of the machine.  
2
(2) Select [Properties].  
In Windows 7, select [Printer Properties].  
40  
CHANGING THE PORT  
Adding or changing a port.  
3
(1) Click the [Ports] tab.  
In Windows 98/Me, click the  
[Details] tab.  
(2) Click the [Add Port]  
button.  
(2)  
(1)  
To change to a previously created port such as USB port, select the desired port  
(USB001, etc.) from the list and click the [Apply] button. This changes the port.  
Select [SC2 TCP/IP Port] and  
then click the [New Port]  
button.  
4
In Windows 98/Me, select [Other],  
[SC2 TCP/IP Port], and then click  
the [OK] button.  
• The "SC2 TCP/IP Port" is added when the printer driver is installed using a  
"Standard installation", or a "Custom installation" with "LPR Direct Print  
(Specify Address/Auto Search)" selected.  
• If the printer driver is installed using a "Custom installation" with "IPP"  
selected, the [SC-Print2005 Port] is added. If you need to change the printer  
port when the machine is connected to an intranet or a wide area network  
(WAN) using the IPP function, select [SC-Print2005 Port], click the [New Port]  
button (the [OK] button in Windows 98/Me), and follow the on-screen  
instructions to create the port again.  
41  
CHANGING THE PORT  
Create the new port.  
5
(1) Enter the  
machine's IP  
address.  
Checking the IP  
address of the  
machine  
(page 6)  
(2) Make sure that  
[LPR] is selected.  
(3) Make sure that  
[lp] is entered.  
(4) Click the [OK]  
button.  
(1)(2)  
(3)  
(4)  
Click the [Close] button in the screen of step 4.  
In Windows 98/Me, this step is not required. Go to the next step.  
6
7
Make sure the created printer port is selected in the printer properties  
window and then click the [Apply] button.  
X When using a port created with "Standard  
TCP/IP Port"  
When using a port created using "Standard TCP/IP Port" in Windows  
2000/XP/Server 2003/Vista/Server 2008/7, in the screen that appears after  
you click the [Configure Port] button in the screen of step 3, make sure the  
[SNMP Status Enabled] checkbox is not selected ( ). If the [SNMP  
Status Enabled] checkbox is selected ( ), it may not be possible to print  
correctly.  
42  
SETUP IN A MACINTOSH  
ENVIRONMENT  
This chapter explains how to install the PPD file to enable printing from a  
Macintosh and how to configure the printer driver settings.  
MAC OS X: this page  
3
(v10.2.8, v10.3.9, v10.4.11, v10.5 - 10.5.8, v10.6)  
MAC OS 9.0 - 9.2.2: page 52  
To use the machine in a Macintosh environment, the machine must be  
connected to a network. A USB connection cannot be used.  
MAC OS X  
The explanations of screens and procedures are primarily for Mac OS X v10.4.  
The screens may vary in other versions of the operating system.  
Insert the "Software CD-ROM" into your computer's CD-ROM drive.  
Insert the "Software CD-ROM" that shows "Disc 2" on the front of the CD-ROM.  
1
Double-click the [CD-ROM] icon ( ) on the desktop.  
2
Double-click the [MacOSX] folder.  
Before installing the software, be sure to read "ReadMe First". "ReadMe First" is in  
the [US-English] folder in the [Readme] folder.  
3
43  
MAC OS X  
Double-click the folder corresponding to the versions of the  
operating system.  
4
v10.2.8  
v10.3.9  
v10.5 -  
10.5.8  
v10.4.11  
v10.6  
Double-click the [MX-PBX1] icon ( ).  
5
6
If the "Authenticate" window appears in Mac OS X v10.2.8, enter the password  
and click the [OK] button.  
Click the [Continue] button.  
The License Agreement window will appear. Make sure that you  
understand the contents of the license agreement and then click the  
[Continue] button.  
7
A message will appear asking you if you agree to the terms of the license. Click the  
[Agree] button.  
If the license appears in the different language, change the language in the  
language menu.  
44  
MAC OS X  
Select the hard drive where the PPD file will be installed and click the  
[Continue] button.  
• Be sure to select the hard drive on which your operating system is installed.  
8
9
• In Mac OS X v10.6, the screen below appears when you click the [Change Install  
Location] button.  
Click the [Install] button.  
Installation begins.  
If an authentication window appears, enter the password and click the [OK]  
button.  
When the installation completed message appears in the installation  
window, click the [Close] button.  
10  
This completes the installation of the software. Next, configure the printer  
driver settings.  
45  
MAC OS X  
Select [Utilities] from the [Go] menu.  
11  
• If you are using Mac OS X v10.5 to 10.5.8 or v10.6,  
click [System Preferences] in the Apple menu ( ) and  
select [Print & Fax] ( ). When the screen for adding  
a printer appears, click the  
14.  
button and go to step  
• If you are using Mac OS X v10.2.8, select  
[Applications] from the [Go] menu.  
Double-click the [Printer Setup Utility] icon ( ).  
If you are using Mac OS X v10.2.8, double-click the [Utilities] folder and then  
double-click the [Print Center] icon.  
12  
13  
If this is the first time you are installing a printer driver on your computer, a  
confirmation message will appear. Click the [Add] button.  
Click [Add].  
46  
MAC OS X  
Configure the printer driver.  
14  
• The procedure for configuring the printer driver varies depending on the  
operating system version. The procedure for versions 10.4.11, 10.5 - 10.5.8 and  
10.6 and the procedure for other versions are explained separately below.  
• The machine can print using the IPP function. If you wish to use the IPP function,  
see "Printing using the IPP function" (page 50) to configure the printer driver  
settings.  
v10.4.11, v10.5 - 10.5.8, v10.6  
(1)  
(2)  
(3)  
(4)  
(1) Click the [Default Browser] icon.  
If you are using Mac OS X v10.5 to 10.5.8 or v10.6, click the [Default] icon.  
(2) Click the machine's model name.  
• Using with AppleTalk:  
The machine's model name usually appears as [SCxxxxxx]*.  
• Using with Bonjour:  
The machine's model name usually appears as [RDVxxxxxx]*.  
* "xxxxxx" is a sequence of characters that varies depending on your model.  
(3) Make sure that the PPD file of your model is selected.  
The PPD file of the machine is automatically selected.  
(4) Click the [Add] button.  
• Using with AppleTalk:  
The PPD file of the machine is automatically selected and the peripheral  
devices installed on the machine are detected and automatically configured.  
• Using with Bonjour:  
The "Installable Options" screen appears. Select the machine configuration  
and click the [Continue] button.  
47  
MAC OS X  
v10.2.8, v10.3.9  
(1)  
(2)  
(3)  
(4)  
(1) Select [AppleTalk].  
If multiple AppleTalk zones are displayed, select the zone that includes the  
printer from the menu.  
(2) Click the machine's model name.  
The machine's model name usually appears as [SCxxxxxx]. ("xxxxxx" is a  
sequence of characters that varies depending on your model.)  
(3) Select the PPD file of the machine.  
• If you are using Mac OS X v10.3.9, select [Auto Select].  
• If you are using Mac OS X v10.2.8, select [Sharp] and click the PPD file of  
your model.  
(4) Click the [Add] button.  
If you are using Mac OS X v10.3.9, the PPD file of the machine is automatically  
selected and the peripheral devices installed on the machine are detected and  
automatically configured.  
The PPD file is installed in the following folders on the startup disk.  
[Library] - [Printers] - [PPDs] - [Contents] - [Resources] - [en.lproj]  
48  
MAC OS X  
Display printer information.  
15  
16  
(2)  
(1)  
(1) Click the machine's name.  
If you are using Mac OS X v10.5 to 10.5.8 or v10.6, click the [Options &  
Supplies] button, click the [Driver] tab and go to step 16.  
(2) Click [Show Info].  
If you are using Mac OS X v10.2.8, select [Show Info] from the [Printers] menu.  
Select the machine configuration.  
If you selected [Auto Select] in (3) of step 14, the machine configuration is detected  
and automatically configured. Check the configured settings to make sure they are  
correct.  
(1) Select [Installable Options].  
If you are using Mac OS X v10.5 to 10.5.8 or v10.6, it does not appear.  
(2) Select the options that are installed on the machine.  
(3) Click the [Apply Changes] button.  
If you are using Mac OS X v10.5 to 10.5.8 or v10.6, click the [OK] button.  
(4) Click to close the window.  
You can check the options that are installed on the machine by printing out the  
"All Custom Setting List" in the system settings. (However, note that "Input Tray  
Options" must be set to the number of trays on the machine.) The "All Custom  
Settings List" can be printed from [List Print (User)] in the system settings.  
This completes the configuration of the printer driver.  
49  
MAC OS X  
X Printing using the IPP function  
The machine can print using the IPP function. If you wish to use the IPP  
function, follow these steps to select the PPD file when configuring the printer  
driver (step 14 on page 47).  
v10.4.11, v10.5 - 10.5.8, v10.6  
(1)  
(2)  
(3)  
(4)  
(1) Click the [IP Printer] icon.  
If you are using Mac OS X v10.5 to 10.5.8 or v10.6, click the [IP] icon.  
(2) Select [Internet Printing Protocol] in "Protocol". Enter the address  
of the machine (IP address or domain name) and the queue name.  
Enter "ipp" in "Queue".  
(3) Select [Sharp] in "Print Using" and click the PPD file of your  
model.  
If you are using Mac OS X v 10.5 to 10.5.8 or v10.6, select [Select a driver to  
use] (or [Select Printer Software]) from "Print Using" and click the PPD file for  
your model.  
(4) Click the [Add] button.  
The "Installable Options" screen will appear. Make sure that the settings are  
correct and click the [Continue] button.  
Checking the IP address of the machine (page 6)  
50  
MAC OS X  
v10.2.8, v10.3.9  
(1)  
(2)  
(3)  
(4)  
(1) Select [IP Printing].  
(2) Select [Internet Printing Protocol] in "Printer Type". Enter the  
address of the machine (IP address or domain name) and the  
"Queue Name".  
• If you are using Mac OS X v10.2.8, enter the address of the machine (IP  
address or domain name) in "Printer's Address".  
• Enter "ipp" in "Queue Name".  
(3) Select [Sharp] in "Printer Model" and click the PPD file of your  
model.  
(4) Click the [Add] button.  
Checking the IP address of the machine (page 6)  
51  
MAC OS 9.0 - 9.2.2  
If you are using Mac OS 9.0 to 9.2.2, make sure that "LaserWriter 8" has been  
installed and that the "LaserWriter 8" checkbox is selected  
in "Extensions  
Manager" in "Control Panels". If not, install it from the system CD-ROM supplied  
with your Macintosh computer.  
Insert the "Software CD-ROM" into your computer's CD-ROM drive.  
Insert the "Software CD-ROM" that shows "Disc 2" on the front of the CD-ROM.  
1
2
3
Double-click the [CD-ROM] icon ( ) on the desktop.  
Double-click the [MacOS] folder.  
Before installing the software, be sure to read "ReadMe First". "ReadMe First" is in  
the [US-English] folder in the [Readme] folder.  
Double-click the [Installer] icon ( ).  
Click the [Install] button.  
4
5
The License Agreement window will appear. Make sure that you  
understand the contents of the license agreement and then click the  
[Yes] button.  
6
52  
MAC OS 9.0 - 9.2.2  
Read the message in the window that appears and click the  
[Continue] button.  
Installation of the PPD file begins.  
7
After the installation, a message prompting you to restart your computer will  
appear. Click the [OK] button and restart your computer.  
This completes the installation of the software. Next, configure the printer  
driver settings.  
Select [Chooser] from the Apple Menu.  
8
Create a printer.  
9
(1)  
(2)  
(3)  
(1) Click the [LaserWriter 8] icon.  
If multiple AppleTalk zones are displayed, select the zone that includes the  
printer.  
(2) Click the machine's model name.  
The machine's model name usually appears as [SCxxxxxx]. ("xxxxxx" is a  
sequence of characters that varies depending on your model.)  
(3) Click the [Create] button.  
53  
MAC OS 9.0 - 9.2.2  
Select the PPD file.  
10  
(1)  
(2)  
(1) Click the PPD file for your model.  
(2) Click the [Select] button.  
• If the above dialog box does not appear and you return to the "Chooser"  
dialog box, follow these steps to select the PPD file manually.  
(1) Make sure that the machine is selected in the "Select a PostScript Printer"  
list, and then click the [Setup] button followed by the [Select PPD] button.  
(2) Select the PPD file for your model and click the [Open] button.  
(3) Click the [OK] button.  
The PPD file is installed in the [Printer Descriptions] folder in the [Extensions] folder.  
Make sure that the machine is selected in the "Select a PostScript  
Printer" list and then click the [Setup] button.  
11  
12  
Click the [Configure] button.  
To automatically configure the settings based on the installed machine options  
that are detected, click the [Auto Setup] button.  
54  
MAC OS 9.0 - 9.2.2  
Select the machine configuration.  
(1) Select the options that are installed on the machine.  
(2) Click the [OK] button.  
13  
You can check the options that are installed on the machine by printing out the  
"All Custom Setting List" in the system settings. (However, note that "Input Tray  
Options" must be set to the number of trays on the machine.) The "All Custom  
Settings List" can be printed from [List Print (User)] in the system settings.  
Click the [OK] button in the window of step 12 to close the window.  
14  
15  
Click the close box ( ) to close the "Chooser".  
This completes the configuration of the printer driver.  
Installing the screen fonts  
The screen fonts for Mac OS 9.0 - 9.2.2 are contained in the [Font] folder of the  
"Software CD-ROM" (Disc 2). Copy the fonts that you wish to install to the  
[System Folder] of the startup disk.  
If you experience problems that may be due to the installed screen fonts,  
immediately delete the installed fonts from the system.  
55  
TROUBLESHOOTING  
4
WHEN INSTALLATION WAS NOT  
SUCCESSFUL  
This section provides solutions to possible installation problems. See the following  
table of contents to locate the appropriate page for your question or problem.  
• The software cannot be installed. . . . . . . . . . . . . . . . . . . . . . . . . . 56  
• The machine is not detected (when connected to a network).. . . . 57  
• The plug and play screen does not appear (USB connection in  
Windows). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58  
• The printer driver is not installed correctly by plug and play (USB  
connection in Windows). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
• The printer driver cannot be installed (Windows 2000/XP/Server  
2003) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60  
Problem  
The  
software  
cannot be  
installed.  
Point to check  
Solution  
Is there sufficient free  
space on your hard  
drive?  
Delete any unneeded files and  
applications to increase free space on  
your hard drive.  
Are you using an  
operating system that is  
not supported?  
Make sure that the software can run  
on your operating system.  
For detailed information on installation  
requirements for each software  
program in Windows, click the [Display  
Readme] button in the installer.  
In a Macintosh environment, this can  
be checked in "ReadMe First" in the  
[US-English] folder in the [Readme]  
folder of the "Software CD-ROM".  
56  
WHEN INSTALLATION WAS NOT SUCCESSFUL  
Problem  
The  
machine is  
not  
detected  
(when  
connected  
to a  
Point to check  
Solution  
Is the IP address of the  
machine configured?  
If the IP address of the machine is not  
configured, the machine will not be  
detected. Make sure that the IP  
address is configured correctly in  
"Network Settings" in the machine's  
system settings (administrator).  
System Settings (Administrator) >  
"Network Settings"  
network).  
Is your computer  
connected to the same  
network as the  
machine?  
Windows:  
If the machine and your computer  
are not connected to the same local  
area network, the machine will not  
be detected. If the two are  
connected to different sub-networks,  
click the [Specify condition] button  
and enter the machine's name (host  
name) or IP address to search for  
the machine.  
Macintosh:  
If multiple AppleTalk zones exist,  
select the zone to which the  
machine is connected from the  
menu.  
Is the machine power  
on?  
If the machine is powered off, it will not  
be detected. Switch on the main power  
switch and the [POWER] key ( ) in  
that order. (In Windows, search again  
after powering on the machine.)  
Is your computer  
connected correctly to  
the machine?  
Make sure that the cable is connected  
securely to the LAN connectors on  
your computer and the machine.  
Check the connections at the hub as  
well.  
CONNECTING TO A NETWORK  
(page 6)  
57  
WHEN INSTALLATION WAS NOT SUCCESSFUL  
Problem  
Point to check  
Solution  
The plug  
and play  
screen  
does not  
appear  
(USB  
connection  
in  
Is the machine power  
on?  
When a USB cable is connected,  
make sure the power of the machine is  
"ON" and then connect a USB cable to  
the machine. When the machine is not  
powered on, switch on the main power  
switch and the [POWER] key ( ) in  
that order.  
Can your computer use  
a USB connection?  
Check your computer whether or not a  
USB interface can be used on the  
Device Manager in your computer.  
(For information on "Device Manager",  
see Help in Windows.)  
Windows).  
If USB can be used, your controller  
chipset type and root hub will appear  
in "Universal Serial Bus controllers" in  
"Device Manager". (The items that  
appear will vary depending on your  
computer.)  
If these two items appear, USB should  
be useable. If a yellow exclamation  
point appears next to "Universal Serial  
Bus controllers" or the two items do  
not appear, refer to your computer  
manual or check with the manufacturer  
of your computer to enable USB and  
then reinstall the printer driver.  
58  
WHEN INSTALLATION WAS NOT SUCCESSFUL  
Problem  
Point to check  
Solution  
The printer  
driver is not  
installed  
correctly by  
plug and  
play (USB  
connection  
in  
Did you connect the  
machine to your  
computer before  
installing the printer  
driver?  
In Windows 2000/XP/Server  
2003/Vista/7, if the machine was  
connected to your computer with a  
USB cable before the printer driver  
was installed from the installer, check  
if information on the unsuccessful  
installation remains in "Device  
Manager". (For information on "Device  
Manager", see Help in Windows.)  
If the model name of the machine  
appears in "Other devices" in "Device  
Manager", delete it, restart your  
computer, and install the printer driver  
again.  
Windows).  
59  
WHEN INSTALLATION WAS NOT SUCCESSFUL  
X The printer driver cannot be installed  
(Windows 2000/XP/Server 2003)  
If the printer driver cannot be installed on Windows 2000/XP/Server 2003, follow  
the steps below to check your computer settings.  
Click the [start] button and then click [Control Panel].  
1
In Windows 2000, click the [Start] button, point to [Settings], and click [Control  
Panel].  
Click [Performance and Maintenance] and then [System].  
2
In Windows 2000, double-click the [System] icon.  
Click the [Hardware] tab and then the [Driver Signing]  
button.  
3
Check the settings in "What action do you want Windows to  
take?" ("File signature verification" in Windows 2000).  
4
If [Block] is selected, the printer driver cannot be installed. Select [Warn] and install  
the printer driver again.  
60  
REMOVING THE SOFTWARE  
To remove the printer driver or software installed using the installer, follow the  
steps below.  
X Windows  
Click the [start] button and then click [Control Panel].  
In Windows 98/Me/NT 4.0/2000, click the [Start] button, point to [Settings], and click  
[Control Panel].  
1
Click [Uninstall a program].  
• In Windows XP/Server 2003, click [Add or Remove Programs].  
2
• In Windows 98/Me/NT 4.0/2000, double-click the [Add/Remove Programs] icon.  
Select the program or driver that you wish to delete.  
For more information, see the manual for the operating system or Help.  
3
Restart your computer.  
4
61  
REMOVING THE SOFTWARE  
X Mac OS X  
Delete the printer that uses the machine's PPD file from the printer  
list.  
To show the printer list, see step 11 and 12 of "MAC OS X" (page 43).  
1
Delete the PPD file.  
2
The PPD file has been copied to the following folder on the startup disk.  
[Library] - [Printers] - [PPDs] - [Contents] - [Resources] - [en.lproj]  
Delete the PPD file of the machine from this folder.  
Delete the installation information.  
The installation information file has been copied to the following folder on the  
startup disk.  
3
[Library] - [Receipts]  
Delete the [MX-PBX1.pkg] file from this folder.  
X Mac OS 9.0 - 9.2.2  
After deleting the icon of the printer that uses the machine's PPD file from the  
desktop, follow the steps below.  
Insert the "Software CD-ROM" into your CD-ROM drive.  
Insert the "Software CD-ROM" that shows "Disc 2" on the front of the CD-ROM.  
1
Double-click the [CD-ROM] icon (  
double-click the [MacOS] folder.  
) on the desktop and  
2
3
4
Double-click the [Installer] icon (  
).  
Select [Remove] in the Install menu and click the [Remove] button.  
62  
SHARP ELECTRONICS CORPORATION  
1 Sharp Plaza, Mahwah, New Jersey 07495-1163.  
SHARP ELECTRONICS OF CANADA LTD.  
335 Britannia Road East, Mississauga, Ontario, L4Z 1W9  
This manual has been printed using a vegetable-based  
soy oil ink to help protect the environment.  
PRINTED IN CHINA  
2010A KS1  
TINSE4637FCZZ  

Xantrex Technology Freedom Hf 1800 User Manual
Subaru Sti Timing Belt User Manual
Panasonic Kx Pw93cl User Manual
Motorola L403c User Manual
MAKITA NHP1310 User Manual
Lexmark Prestige 805 User Manual
HAYWARD HEATPRO HP20854T User Manual
GE ADTS552F User Manual
EPSON ACULASER MX21 User Manual
CRAFTSMAN 917.270670 User Manual