Samsung Officeserv 7100 User Manual

Ed. 00

OfficeServ 7100

Installation Manual

OfficeServ 7100 Installation Manual

INTRODUCTION

Purpose

OfficeServ 7100 is the most suitable system for offices using circuit lines with 10 to 25

subscribers. This manual describes the condition for OfficeServ 7100 system installation

and how to install, inspect and operate the system.

Document Content and Organization

This document consists of eight chapters, and abbreviations as follows:

CHAPTER 1. Before Installing

This chapter describes the checklists, such as the installation site and the grounding & the

power conditions, to be inspected before installing the OfficeServ 7100 system.

This chapter also describes the items included in the OfficeServ 7100 package and the

installation procedure.

CHAPTER 2. Installing Cabinets

This chapter describes how to install an OfficeServ 7100 cabinet on the ground or inside a

rack, depending on the installation environment, and how to connect the grounding wire.

CHAPTER 3. Mounting and Replacing Boards

This chapter describes how to mount or replace various boards of the OfficeServ 7100

system.

CHAPTER 4. Connecting External Batteries

This chapter describes how to connect an external battery to the OfficeServ 7100 system.

CHAPTER 5. Connecting the Power

This chapter describes how to connect the power to the OfficeServ 7100 system.

CHAPTER 6. Connecting C.O. Lines

This chapter describes how to connect C.O. lines to the OfficeServ 7100 system.

Ошибка! Стиль не определен.

CHAPTER 7. Connecting Stations and Additional Equipment

This chapter describes how to connect various stations and additional equipment, such as

analog/digital phones, door phones and door locks, to the OfficeServ 7100 system.

CHAPTER 8. Starting the System

This chapter describes items to check before starting the OfficeServ 7100 system, the procedure

for starting the system, and the procedure for testing whether the system is normally operating

after startup.

ABBREVIATION

Abbreviations frequently used in this document are described.

Conventions

The following types of paragraphs contain special information that must be carefully read

and thoroughly understood. Such information may or may not be enclosed in a rectangular

box, separating it from the main text, but is always preceded by an icon and/or a bold title.

WARNING

Provides information or instructions that the reader should follow in order to avoid

personal injury or fatality.

CAUTION

Provides information or instructions that the reader should follow in order to avoid

a service failure or damage to the system.

CHECKPOINT

Provides the operator with checkpoints for stable system operation.

NOTE

Indicates additional information as a reference.

OfficeServ 7100 Installation Manual

Reference

OfficeServ 7100 System Manual

This document introduces OfficeServ 7100 and describes the system information, such as

hard configuration, specification, and functions, necessary for this system.

OfficeServ 7100 Programming Manual

This document describes how to use the MMC program to change the OfficeServ 7100

system setting by using a phone.

Revision History

EDITION

DATE OF ISSUE

REMARKS

08. 2006.

01.2007.

04.2007.

Original Draft

Safety, VM and Router etc.

DoC, 2BRM Modular Jack Connection

III

Ошибка! Стиль не определен.

This page is intentionally left blank.

OfficeServ 7100 Installation Manual

SAFETY CONCERNS

For product safety and correct operation, the following information must be given to the

operator/user and shall be read before the installation and operation.

Symbols

Caution

Indication of a general caution

Restriction

Indication for prohibiting an action for a product

Instruction

Indication for commanding a specifically required action

Ошибка! Стиль не определен.

Warning

WARNING

Caution for Grounding

- Do not connect the grounding wire of the OfficeServ 7100 system to a power

conduit of a building

- The standards for power and grounding should comply with the country standard

and the pertinent work should be conducted according to the country standard.

- External grounding is required to prevent human injuries or system damages

caused by lightning, static electricity, or voltage surge.

- Unplug the AC power cord before connecting the grounding wire. Failure to do

so may cause human injury.

- The OfficeServ 7100 system should be connected to an outlet with a protective

ground.

- The GND in the back panel of the OfficeServ 7100 system should be grounded.

Use of Double-pole/neutral fusing

If the system is repaired after removing only one fuse used in the neutral line,

it may cause electric shock. If the repair is required, repair the system after

extracting the plug of the power cord.

Caution for powers when mounting boards

Check if the cabinet power is off when mounting boards on slots. Inserting or

ejecting a board while the power is on may damage the board.

Caution for the connection of the ground cable

Unplug the AC power cord before connecting the ground cable. If the connection

work is performed when the power cable is connected, it may cause serious

bodily damage.

OfficeServ 7100 Installation Manual

Caution

CAUTION

Caution for Installation

Only a trained service staff can install the OfficeServ 7100 system.

The equipment intended only for installation in a RESTRICTED ACCESS

LOCATION

Caution for the connection of External Batteries

Do not connect an external AC power until the battery and the system is

completely disconnected. To do so may cause electric shock to the constructor or

the system.

Make sure that the specified polarities(+, -) are correctly connected when

connecting external batteries.

To reduce risk of fire and injury to persons, use only a sealed nickel cadmium or

lead-acid battery supply capable of handling a charge current of 0.25 A, a charge

voltage of -54 V dc and a discharge rate of 26 Ah.

Leakage currents due to ringing voltage – Earthing installation instructions

1. A supplementary equipment earthing conductor is to be installed between the

product or system and earth, that is, in addition to the equipment earthing conductor

in the power supply cord.

2. The supplementary equipment earthing conductor may not be smaller in size than

the unearthed branch-circuit supply conductors. The supplementary equipment

earthing conductor is to be connected to the product at the terminal provided, and

connected to earth in a manner that will retain the earth connection when the power

supply cord is unplugged. The connection to earth of the supplementary earthing

conductor shall be in compliance with the appropriate rules for terminating bonding

jumpers in Part K of Article 250 of the National Electrical Code, ANSI/NFPA 70 and

Article 10 of Part 1 of the Canadian Electrical Code, Part 1, C22.1. Termination of

the

supplementary earthing conductor is permitted to be made to building steel, to a

metal electrical raceway system, or to any earthed item that is permanently and

reliably connected to the electrical service equipment earthed.

3. Bare, covered, or insulated earthing conductors are acceptable. A covered or

insulated conductor must have a continuous outer finish that is either green, or

green with one or more yellow stripes.

VII

Ошибка! Стиль не определен.

Separation of TNV and SELV - Pluggable A

The separate protective earthing terminal provided on this product shall be

permanently connected to earth. (Instruction)

Telephone line cord

To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed

or CSA Certified Telecommunication Line Cord.

Safety Instructions for Rack Mount

The following or similar rack-mount instructions are included with the installation

instructions:

- Elevated Operating Ambient If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack environment may be greater than

room ambient. Therefore, consideration should be given to installing the

equipment in an environment compatible with the maximum ambient temperature

(Tma) specified by the manufacturer.

- Reduced Air Flow: Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation of the equipment is not

compromised.

- Mechanical Loading: Mounting of the equipment in the rack should be such that

a hazardous condition is not achieved due to uneven mechanical loading.

- Circuit Overloading: Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits might

have on over-current protection and supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

- Reliable Earthing: Reliable earthing of rack-mounted equipment should be

maintained. Particular attention should be given to supply connections other than

direct connections to the branch circuit (e.g. use of power strips)."

Prohibition of Metal Accessories

Do not wear metal accessories such as rings and watches to prevent electric

damages to the system.

VIII

OfficeServ 7100 Installation Manual

Un-allowed Use of Selector Switch

The OfficeServ 7100 system only use 230 V. Do not change the input power

freely by means of the selector switch.

AC Power Connection Inhibited

Do not operate other devices with the AC power of the OfficeServ 7100 system or

with the DC power of external batteries.

Check of Power-off

Check if the cabinet power is off when mounting boards on slots. Inserting or

ejecting a board while the power is on may damage the board.

Board Reset

New settings are applied only after the board is reset. The system may

malfunction if the board is not properly initialized.

Caution for Installation

Only a trained service staff can install the OfficeServ 7100 system.

Ошибка! Стиль не определен.

This page is intentionally left blank.

OfficeServ 7100 Installation Manual

TABLE OF CONTENTS

INTRODUCTION

Purpose ................................................................................................................................................. I

Document Content and Organization..................................................................................................... I

Conventions........................................................................................................................................... II

Reference............................................................................................................................................. III

Revision History.................................................................................................................................... III

SAFETY CONCERNS

Symbols................................................................................................................................................IV

Warning.................................................................................................................................................IV

Caution .................................................................................................................................................IV

CHAPTER 1. Before Installing

1-4

1.1

Site Information ..................................................................................................................... 1-4

1.1.1 Safety Conditions..................................................................................................................1-4

1.1.2 Temperature and Humidity....................................................................................................1-4

1.2

1.3

1.4

Grounding Conditions .......................................................................................................... 1-4

Power Conditions.................................................................................................................. 1-4

Checking the Package .......................................................................................................... 1-4

CHAPTER 2. Installing Cabinets

2-4

2.1

2.2

2.3

Procedure for the System Installation ................................................................................. 2-4

Selecting Installation Method............................................................................................... 2-4

Installing in a Rack ................................................................................................................ 2-4

2.3.1 Cautions for Installation.........................................................................................................2-4

2.3.2 Tools Required ......................................................................................................................2-4

2.3.3 Installing in a Rack ................................................................................................................2-4

2.4

Installing on a Wall ................................................................................................................ 2-4

2.4.1 Tools Required ......................................................................................................................2-4

2.4.2 Installing on a Wall ................................................................................................................2-4

Ошибка! Стиль не определен.

2.5

Connecting the Grounding Wire...........................................................................................2-4

CHAPTER 3. Mounting and Replacing Boards

3-4

3.1

3.2

Cabinet Configuration ...........................................................................................................3-4

Mounting Control Boards......................................................................................................3-4

3.2.1 Setting Switches and Mounting Option Boards....................................................................3-4

3.2.2 Mounting Control Boards ......................................................................................................3-4

3.3

Mounting Interface Boards....................................................................................................3-4

3.3.1 Setting Switches and Mounting Optional Boards .................................................................3-4

3.3.2 Mounting Interface Boards to Slots.......................................................................................3-4

3.4

3.5

Connecting Power Fail Transfer ...........................................................................................3-4

Replacing Boards...................................................................................................................3-4

CHAPTER 4. Connecting External Batteries

4-4

4.1

4.2

Cautions for Connecting External Batteries........................................................................4-4

Connecting External Batteries..............................................................................................4-4

CHAPTER 5. Connecting the Power

5-4

5.1

5.2

Cautions when Connecting Power .......................................................................................5-4

Connecting the Power ...........................................................................................................5-4

CHAPTER 6. Connecting C.O. Line

6-4

6.1

6.2

Line Conditions......................................................................................................................6-4

Connecting the C.O. Line ......................................................................................................6-4

6.2.1 Cautions to Connect the C.O. Line.......................................................................................6-4

6.2.2 Connecting Common C.O. Line............................................................................................6-4

6.2.3 Connecting T1/E1/PRI ..........................................................................................................6-4

CHAPTER 7. Connecting Stations and Additional Equipment

7-4

7.1

Connecting Stations ..............................................................................................................7-4

7.1.1 Cautions for Connecting Stations..........................................................................................7-4

7.1.2 Connecting Analog Phones...................................................................................................7-4

7.1.3 Connecting Digital Phones....................................................................................................7-4

7.1.4 Connecting IP Phones ..........................................................................................................7-4

7.1.5 Connecting to a Door Phone and a Door Lock.....................................................................7-4

XII

OfficeServ 7100 Installation Manual

7.2

Connecting Additional Equipment....................................................................................... 7-4

7.2.1 Connecting MOH/BGM Equipment ......................................................................................7-4

7.2.2 Connecting External/Additional Page Equipment.................................................................7-4

7.2.3 Connecting Common Bell.....................................................................................................7-4

7.2.4 Changing System Setting .....................................................................................................7-4

7.2.5 Connecting SMDR ................................................................................................................7-4

7.2.6 Connecting Printers...............................................................................................................7-4

CHAPTER 8. Starting the System

8-4

8.1

Pre-Check............................................................................................................................... 8-4

8.1.1 Environment..........................................................................................................................8-4

8.1.2 Safety Conditions..................................................................................................................8-4

8.2

8.3

8.4

Starting the System............................................................................................................... 8-4

Numbering Extensions and C.O. Lines ............................................................................... 8-4

Checking System Operation................................................................................................. 8-4

8.4.1 Station Call Function .............................................................................................................8-4

8.4.2 Station Camp-On Function....................................................................................................8-4

8.4.3 C.O. Line Call Function.........................................................................................................8-4

8.4.4 C.O. Line Camp-On Function ...............................................................................................8-4

ABBREVIATION

4 ~ I.......................................................................................................................................................IV

K ~ W....................................................................................................................................................IV

XIII

Ошибка! Стиль не определен.

LIST OF FIGURES

Figure 2.1 Tools for the Installation inside a Rack...................................................................2-4

Figure 2.2 Rack Installation (1) ...............................................................................................2-4

Figure 2.3 Rack Installation (2) ...............................................................................................2-4

Figure 2.4 Rack Installation (3) ...............................................................................................2-4

Figure 2.5 Required Tools for the installation on a Wall ..........................................................2-4

Figure 2.6 Installation on a Wall (1).........................................................................................2-4

Figure 2.7 Installation on a Wall (2).........................................................................................2-4

Figure 2.8 Installation on a Wall (3).........................................................................................2-4

Figure 2.9 Installation on a Wall (4).........................................................................................2-4

Figure 2.10 Installation on a Wall (5).......................................................................................2-4

Figure 2.11 Installation on a Wall (6).......................................................................................2-4

Figure 2.12 Installation on a Wall (7)......................................................................................2-4

Figure 2.13 Grounding............................................................................................................2-4

Figure 3.1 Front/rear View of OfficeServ 7100 Cabinet...........................................................3-4

Figure 3.2 Setting Switches of MP10/11 Board.......................................................................3-4

Figure 3.3 Mounting a Modem Board on the MP10/11 Board .................................................3-4

Figure 3.4 Mounting 4SWM/4DLM on the MP10/11 Board .....................................................3-4

Figure 3.5 Mounting the Control Board to Slot 0.....................................................................3-4

Figure 3.6 Inserting the Control Board to a connector of the Main Board ...............................3-4

Figure 3.7 Mounting the UNI Board ........................................................................................3-4

Figure 3.8 Setting the Switch of the TEPRI Board ..................................................................3-4

Figure 3.9 Setting Switches of the TEPRI2 Board ..................................................................3-4

Figure 3.10 PLIM Board..........................................................................................................3-4

Figure 3.11 Mounting an Interface Board on a Slot.................................................................3-4

Figure 3.12 Inserting a control Board to the Connector of the Main Board .............................3-4

Figure 3.13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board.....................................3-4

Figure 3.14 Turning the Cabinet Power Off.............................................................................3-4

Figure 3.15 Removing a Board ...............................................................................................3-4

Figure 3.16 Replacing a New Board .......................................................................................3-4

Figure 4.1 Connecting an External Battery...........................................................................4-4

Figure 5.1 Connecting the Power (use of a cabinet)...............................................................5-4

Figure 6.1 RJ-45 Port of 4TRM//8TRK Board .........................................................................6-4

Figure 6.2 RJ-45 Port(T-Mode only) of 2BRM Board ..............................................................6-4

XIV

OfficeServ 7100 Installation Manual

Figure 6.3 RJ-45 Port of TEPRI Board................................................................................... 6-4

Figure 7.1 RJ-45 Port of 4SLM Board .................................................................................... 7-4

Figure 7.2 RJ-45 Port of 16SLI2 Board .................................................................................. 7-4

Figure 7.3 RJ-45 Port of 8COMBO Board (for Analog Phone Connection) ............................ 7-4

Figure 7.4 RJ-45 Port of 4DLM Board.................................................................................... 7-4

Figure 7.5 RJ-45 Port of a 8DLI (for a digital phone).............................................................. 7-4

Figure 7.6 RJ-45 Port of 8COMBO Board (for digital phone) ................................................. 7-4

Figure 7.7 IP Phone Layout.................................................................................................... 7-4

Figure 7.8 RJ-45 Port of Ethernet Connection Board............................................................. 7-4

Figure 7.9 RJ-45 Port of 8DLI/16DLI2/8COMBO/4DLM Boards (for Door Phone) ................. 7-4

Figure 7.10 Connecting MOH/BGM Sources ......................................................................... 7-4

Figure 7.11 Connecting External/Additional Page Equipment ................................................ 7-4

Figure 7.12 Connecting Common Bells.................................................................................. 7-4

Figure 7.13 WebMMC Initial Screen....................................................................................... 7-4

Figure 7.14 Connecting SMDR............................................................................................... 7-4

Figure 7.15 Connecting Printers............................................................................................. 7-4

LIST OF TABLES

Table 1.1 Power Standards..................................................................................................... 1-4

Table 1.2 Package Items........................................................................................................ 1-4

Table 3.1 Mountable Boards on Slots..................................................................................... 3-4

Table 3.2 Parts on the Rear Panel of the Cabinet .................................................................. 3-4

Table 3.3 Switches of MP10/11 Board.................................................................................... 3-4

Table 3.4 Control Board Types ............................................................................................... 3-4

Table 3.5 Interface Board for Switche/Jumper Setting............................................................ 3-4

Table 3.6 Interface Boards that can mount option boards ...................................................... 3-4

Table 3.7 Interface Board Types and Available Slots.............................................................. 3-4

Table 6.1 Line condition of OfficeServ 7100 ........................................................................... 6-4

Table 7.1 Distance Between Stations and the System ........................................................... 7-4

Table 7.2 Specification of the SMDR System ......................................................................... 7-4

Ошибка! Стиль не определен.

This page is intentionally left blank.

XVI

OfficeServ 7100 Installation Manual

CHAPTER 1. Before Installing

This chapter describes items to check when inspecting the installation site and the

grounding and power conditions before installing the OfficeServ 7100 system. This chapter

also describes the items included in the OfficeServ 7100 package and the installation

procedure.

1.1 Site Information

Select a site that satisfies the following conditions for safety, temperature and humidity:

1.1.1 Safety Conditions

The OfficeServ 7100 system should not be installed near materials that can cause a fire,

such as explosive gas and inflammables.

The OfficeServ 7100 system should not be near equipments that generate

electromagnetic waves, such as monitors or copying machines.

The installation location should be convenient for distributing trunk lines and

extension lines, for connecting power and grounding wires, and for maintenance and

repair.

The OfficeServ 7100 system should not be installed in aisles or passageways that are

populated or used for moving equipment.

Always maintain cleanliness to prevent dust from damaging the board-connecting part

of the cabinet.

Before installing the OfficeServ 7100 system, check items such as the electric wiring

status, grounding status, voltage and frequency.

1.1.2 Temperature and Humidity

The conditions for temperature and humidity are as follows:

− Operation Temperature: 0~40°C

− Storage temperature: -10~50°C

− Humidity: 10~90%

Cool area without direct sunlight

Ventilators should be installed to remove dust.

1-1

CHAPTER 1. Ошибка! Стиль не определен.

1.2 Grounding Conditions

The following cautions should be taken when grounding the OfficeServ 7100 system:

The grounding wire of the OfficeServ 7100 system should be grounded to the earth

using a proper material.

The flow of electric current between the grounding wire of the power plug and the

exposed metal surface of the system should be satisfactory.

When connecting grounding of external additional equipments to the grounding of the

system, the groundings should be connected through a single connection point.

Cautions for Grounding

- Do not connect the grounding wire of the OfficeServ 7100 system to a power

conduit of a building.

- The standards for power and grounding should comply with the country

standard and the pertinent work should be conducted according to the country

standard.

- External grounding is required to prevent human injuries or system damages

caused by lightning, static electricity, or voltage surge.

- Unplug the AC power code before connecting the ground line. Failure to do so

may cause bodily damage.

- OfficeServ 7100 System should be connected to an outlet with a protective

ground.

- The GND in the back of the OfficeServ 7100 system should be grounded.

1.3 Power Conditions

The power supply board of the OfficeServ 7100 system receives AC input power or battery

power, and supplies -54 V, -5 V, +5 V, +3.3 V, +12 V, and -54 V(Battery) to the system

cabinet.

The power condition is as follows:

AC 220-240V, 1.5 A, 50/60 Hz, or DC 48 V, 3 A

Table 1.1 Power Standards

Power Supply

Power Supply Input Power AC 230 V

Unit(PSU)

Standards

Output

Power

- DC -54 V, 1.1 A

- DC +5 V, 5 A

- DC -5.3 V, 0.3 A

- DC +3.3 V, 5 A

- DC +12 V, 0.4 A

- DC -54 V, 0.25 A(for backup)

1-2

OfficeServ 7100 Installation Manual

1.4 Checking the Package

The list of items included in the OfficeServ 7100 package is as follows:

Table 1.2 Package Items

Category

Interface Board

TEPRI, TEPRI2

Slots Available

Voice C.O. line

Slot 1 and Slot 2 of the cabinet

8TRK, UNI

Voice extension

16DLI2, 8DLI, 16SLI2, 8SLI, 8Combo, UNI

Data voice

application

MGI, MGI64

LIM

References

For the detailed features and functions for each interface board, refer to ‘OfficeServ

7200 System manual’.

The Procedure for mounting the interface board to each slot is as follows:

1) Check the exterior of the interface board for any damages.

2) Align each Interface board to the guardrail of the universal slot of the OfficeServ 7100

basic cabinet or expansion cabinet, and slide the Interface board into the slot.

Figure 3.11 Mounting an Interface Board on a Slot

3-11

CHAPTER 3. Ошибка! Стиль не определен.

3) Press and lock the lever on the front panel of the interface board to fully insert to the

connector of the OfficeServ 7100 main board.

Figure 3.12 Inserting a control Board to the Connector of the Main Board

3-12

OfficeServ 7100 Installation Manual

3.4 Connecting Power Fail Transfer

4TRM and 4SLM option boards do not support Power Fail Transfer function.

If AC power is fails while battery is not connected, connect a power fail transfer circuit by

connecting C.O. lines to extensions. If a pair of trunk lines(8TRK) is connected to pin1 and

pin2 of the first port in 16SLI2 or 8SLI, the lines are connected to a typical phone through

Pin 4 and 5 in 8TRK. In power failure, emergency calls can be available since the C.O. line

is directly connected to the phone by the internal relay operation.

Figure 3.13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board

3-13

CHAPTER 3. Ошибка! Стиль не определен.

3.5 Replacing Boards

If the OfficeServ 7100 system fails to operate normally due to an error on the power supply

board, control board, or interface board, replace the board to a new one.

Removing Cables

Replace a board after removing all cables connected to the board.

The procedure for replacing a board mounted in a slot of a cabinet is as follows:

1) Turn off the power of the cabinet equipped with the board to be removed.

Figure 3.14 Turning the Cabinet Power Off

2) Extract the board by pulling the lever of the board carefully.

Figure 3.15 Removing a Board

3-14

OfficeServ 7100 Installation Manual

3) Align the new board to the guardrail of the slot, and slide the new board into the slot.

After then, lock the lever in the front panel of the board to fully insert into the

connector of the OfficeServ 7100 main board.

Figure 3.16 Replacing a New Board

3-15

CHAPTER 3. Ошибка! Стиль не определен.

This page is intentionally left blank.

3-16

OfficeServ 7100 Installation Manual

CHAPTER 4. Connecting External

Batteries

This chapter describes how to connect external batteries.

4.1 Cautions for Connecting External Batteries

External batteries are required to ensure stable operation of the OfficeServ 7100

system in case a power failure occurs. The rated capacity of an external battery is DC

48V per cabinet. Batteries should be connected to each cabinet to guarantee safety and

a fuse(125 VAC, 5 A) should be positioned between the output terminal of the battery

and the battery connector of the cabinet

Cautions for connecting an external battery

Do not connect external AC power to the system before connecting an external

battery to the system. To do so, may cause electric shock for the system or the

constructor.

Make sure that the polarities(+/-) between the external battery ant the system are

equal.

To reduce risk of fire and injury to persons, use only a sealed nickel cadmium or

lead-acid battery supply capable of handling a charge current of 0.25 A, a charge

voltage of -54 V dc and a discharge rate of 26 Ah.

4-1

CHAPTER 4. Ошибка! Стиль не определен.

4.2 Connecting External Batteries

The procedure for using a battery cable to connect an external battery to the OfficeServ

7100 system is as follows:

1) Prepare the battery cable that was provided with the OfficeServ 7100 system. An end

of this battery cable consists of a white line and a black line.

2) Connect the white line of the battery cable to the (+) terminal, and the black line to the

(-) terminal of the battery. Then, connect the other end of the battery cable to the

external battery socket on the rear panel of the OfficeServ 7100 cabinet. When using

two or more OfficeServ cabinets, prepare as much external batteries as the number of

cabinets and connect the batteries to each cabinet.

Figure 4.1 Connecting an External Battery

4-2

OfficeServ 7100 Installation Manual

CHAPTER 5. Connecting the Power

This chapter describes how to connect power to the OfficeServ 7100 system.

5.1 Cautions when Connecting Power

When input power is normally supplied, the AC power is supplied to the Power Supply

Unit(PSU), which charges the external battery. If the input power is interrupted, the system

can be operated using the charged power of the external battery.

Cautions to be taken when connecting power to the OfficeServ 7100 system are as follows:

AC power of the system only supports 230V.

A single AC outlet should be used solely for the system’s AC power. Sharing the AC

power with other devices can cause noise or a voltage drop, resulting in a system

malfunction or fire.

Use a stable power source that can always supply AC power since instantaneous

power failures can cause malfunctions or battery failures. Procedure for Connecting

Power.

5-1

CHAPTER 5. Ошибка! Стиль не определен.

5.2 Connecting the Power

Single cabinet configuration

Use the power cable provided with the OfficeServ 7100 system to connect the input power

terminal on the back panel of the basic cabinet to a grounded outlet.

Figure 5.1 Connecting the Power (use of a cabinet)

5-2

OfficeServ 7100 Installation Manual

CHAPTER 6. Connecting C.O. Line

This chapter describes how to connect the C.O. line to the OfficeServ 7100 system after

installation.

6.1 Line Conditions

Cautions for connecting C.O. lines are as follows:

Us the cables with AWG #24 or AWG #26 thickness.

When wiring cables in high-humidity areas, remove moisture before wiring.

Cables should be handled carefully to prevent any distortions or damages.

Subscriber lines should be kept indoors if at all possible.

Do not cable subscriber lines around any high-voltage power line.

Leak resistance for the C.O. line connected to the OfficeServ 7100 system is as follows:.

Table 6.1 Line condition of OfficeServ 7100

Line Condition

Leak Resistance

20 kΩ or higher

Leak Resistance between Lines

Leak Resistance Between Grounds

6-1

CHAPTER 6. Ошибка! Стиль не определен.

6.2 Connecting the C.O. Line

This section describes how to connect a common C.O. line(4TRM/2BRM of the UNI and

8TRK board) and PRI C.O. lines(TEPRI/TEPRI2 board).

6.2.1 Cautions to Connect the C.O. Line

Cautions to prevent bodily injuries and system damages when connecting the C.O. line are

as follows:

Do not connect the C.O. line in extreme weather conditions such as storm and

lightning.

Do not connect the C.O. line in areas with moisture.

6.2.2 Connecting Common C.O. Line

Use a pair of AWG #24(or AWG #26) cable to connect a common C.O. line to the terminal

pin of a terminal box connected to the OfficeServ 7100 system equipped with a 4TRM or

2BRM board.

P1-P4 Ports

(RJ-45)

Pin No.

Function

C.O TIP

C.O RING

Figure 6.1 RJ-45 Port of 4TRM//8TRK Board

P1, P2 Ports

(RJ-45)

Pin No.

Function

TX +

RX +

RX -

TX -

Figure 6.2 RJ-45 Port(T-Mode only) of 2BRM Board

6-2

OfficeServ 7100 Installation Manual

6.2.3 Connecting T1/E1/PRI

TEPRI boards can be connected to a T1/E1 C.O. line through a RJ-45 port.

As shown below, connect a T1 type C.O. line or an E1 type PRI C.O. line to the T1/E1/PRI

port of the TEPRI/TEPRI2 built in the OfficeServ 7100 system.

T1/E1/PRI Port

(RJ-45)

Pin No.

E1 Mode

Function

Tx+

Tx-

Rx-

Rx+

Figure 6.3 RJ-45 Port of TEPRI Board

6-3

OfficeServ 7100 Installation Manual

CHAPTER 7. Connecting Stations and

Additional Equipment

This chapter describes how to connect various stations and additional equipment, such as

analog/digital phones, door phones and door locks.

7.1 Connecting Stations

7.1.1 Cautions for Connecting Stations

Take the following cautions when connecting stations:

Do not connect stations in weather conditions such as storm and lightning.

Do not connect stations in a humid area.

Comply with the manual of the station and with this document when reconnecting

stations or changing connections.

Connect stations to a pair of #24 AWG or #26 AWG cables.

The distances between stations and the OfficeServ 7100 system are as follows:

Table 7.1 Distance Between Stations and the System

Installation Distance

Digital Phone

Standards

Maximum 400 m(for AWG #24)

Maximum 1 km(for AWG #24)

Maximum 400 m(for AWG #24)

Analog Phone

Door Phone

AOM

7-1

CHAPTER 7. Ошибка! Стиль не определен.

7.1.2 Connecting Analog Phones

Connect an analog phone to the 4SLM of the UNI board, 8SLI/16SLI2, 8COMBO or UNI

board mounted on the OfficeServ 7100 system.

Connecting to the 4SLM of a UNI Board

Connect an analog phone to the ports of a 4SLM of the UNI board by using a pair of AWG

#24 or AWG #26 cables.

P1-P4 Ports

(RJ-45)

Pin No.

Function

SLI

TIP

SLI

RING

Figure 7.1 RJ-45 Port of 4SLM Board

Connecting to a 8SLI/16SLI2 Board

Connect an analog phone to the port of a 16SLI board by using a pair of AWG #24 or AWG

#26 cables.

P1-P8 Ports

(RJ-45)

P1 Port

Pin No.

Function

PFT

TIP

PFT

TIP

SLI 1

TIP

SLI 1

RING

PFT

TIP

PFT

TIP

(8SLI)

(16SLI2) (16SLI2)

P2-P16 Ports

Pin No.

Function

SLI

TIP

SLI

RING

Figure 7.2 RJ-45 Port of 16SLI2 Board

7-2

OfficeServ 7100 Installation Manual

Connecting to a 8COMBO Board

Connect an analog phone to the ports of a 8COMBO board by using a pair of AWG #24 or

AWG #26 cables.

P1-P8 Ports

(RJ-45)

P1-P8 Ports

Pin No.

Function

SLI TIP

SLI

RING

Figure 7.3 RJ-45 Port of 8COMBO Board (for Analog Phone Connection)

7-3

CHAPTER 7. Ошибка! Стиль не определен.

7.1.3 Connecting Digital Phones

Connect a digital phone to the 4DLM of the UNI board, 8DLI, 16DLI2 and 8COMBO

board.

Connecting to the 4DLM of a UNI Board

Connect an analog phone to the ports of a 4DLM of the UNI board by using a pair of AWG

#24 or AWG #26 cables.

P1-P4 Ports

(RJ-45)

P1-P4 Ports

Pin No.

Function

DLI

TIP

DLI

RING

Figure 7.4 RJ-45 Port of 4DLM Board

Connecting to a 8DLI/16DLI2 Board

Connect a digital phone to the ports of a 8DLI board by using a pair AWG #24 or AWG

#26 cables.

P1-P8(P16)

Ports

(RJ-45)

P1-P16 Ports

Pin No.

Function

DLI

TIP

DLI

RING

Figure 7.5 RJ-45 Port of a 8DLI (for a digital phone)

7-4

OfficeServ 7100 Installation Manual

Connecting to a 8COMBO Board

Connect a digital phone to the ports of the 8COMBO board by using a pair AWG #24 or

AWG #26 cables.

P1-P8 Ports

(RJ-45)

Pin No.

Function

DLI TIP

DLI

RING

Figure 7.6 RJ-45 Port of 8COMBO Board (for digital phone)

Maximum number of DS-5012L phones connectable

Up to eight DS-5012L phones can be connected to each DLI board(8DLI/16DLI2)

of the OfficeServ 7100 system. If more than eight DS-5012L phones are

connected to the DLI board, the power for all digital phones connected to the

same board is blocked automatically. Up to 24 DS-5012L phones can be

connected to the basic cabinet or the expansion cabinet.

7-5

CHAPTER 7. Ошибка! Стиль не определен.

7.1.4 Connecting IP Phones

IP phone is a phone that provides calls through Ethernet LAN. The interface between a

digital phone connected to the OfficeServ 7100 system and an IP phone connected to LAN

is as follows. In default, the MP10/11 board supports eight MGI channels. Therefore, IP

phones are available even if additional MGI16/MGI64 boards are not mounted.

1) The connection between a digital phone and an IP phone is established or released

using the IP address of the LAN connected to the OfficeServ 7100 system.

2) The digital phone connected to the OfficeServ 7100 system converts the analog voice

data to PCM voice data and transmits the data to the MP10/MP11 or MGI boards via

through 16 DLI2 board

3) PCM voice data is converted to packet data by the MP10/MP11 board and transferred

to the IP phone.

4) The IP phone converts packet voice data to analog voice signals and displays the

signals through a handset or a speaker.

5) Voice signals coming from the IP phone is converted to packet data and transmitted to

the MP10/MP11 or MGI board in the same way. The MP10/MP11 or MGI board

converts the packet voice data to PCM voice data and transmits the data to the digital

phone through the 16DLI2 board. The digital phone converts and sends the PCM voice

data to analog data.

Use after the MMC setting suitable for the system.

OfficeServ 7100

MP10

16DLI

IP Telephone

Digital Telephone

Figure 7.7 IP Phone Layout

7-6

OfficeServ 7100 Installation Manual

7.1.4.1 Connecting Boards to Ethernet

LIM/MGI/MGI64/MP10/MP11/4SWM board can be connected to Ethernet by using an

Ethernet cable

RJ-45 Port

LIM Board-All ports(P1~P16)

4SWM Board-Line Ports(P1~P4)

MP10/11, MGI16/MGI64 Board-LAN Port

Pin No.

Function

Tx+

Tx-

Rx+

Rx-

Figure 7.8 RJ-45 Port of Ethernet Connection Board

7.1.5 Connecting to a Door Phone and a Door Lock

Connect a door phone and a door lock to the OfficeServ 7100 system by using a Door

Phone Interface Module(DPIM). Connect a pair of #24 AWG or #26 AWG cables to the

LINE port of DPIM and the ports of 8DLI/16DLI2/8COMBO/4DLM board of the

OfficeServ 7100 system.

Connecting to 8DLI/16DLI2/4DLM Boards

Pin No.

Function

DLI TIP

DLI

RING

Figure 7.9 RJ-45 Port of 8DLI/16DLI2/8COMBO/4DLM Boards (for Door Phone)

1) Connect the Door port of DPIM and the line port of DOOR BOX port.

2) When using an automatic door lock, connect the Lock port of the DPIM and the door

phone contact point to the door lock.

The door lock contact point is designed to control low-voltage relay and uses 24 VDC and

100 mA.

MMC Related

MMC 211 is used to assign call numbers to door phones.

7-7

CHAPTER 7. Ошибка! Стиль не определен.

7.2 Connecting Additional Equipment

This section describes how to connect optional equipment, such as Music on

Hold(MOH)/Background Music(BGM) sources, external page devices and common bells,

to the OfficeServ 7100 system.

7.2.1 Connecting MOH/BGM Equipment

The OfficeServ 7100 system offers music when while on hold.

The system provides internal tone/music and external music sources per C.O. or extension

lines as the music source. The selection of internal/external music sources is performed

through MMC 861. One external music source is provided while on hold, and the external

music source is connected to the MISC port.

If a pair of MOH/BGM Source lines is connected to pin4 and pin5 of the MISC port in

MP10(MP11).

MOH/BGM source of a user

Figure 7.10 Connecting MOH/BGM Sources

MMC Related

Select music sources for C.O. lines through MMC 408 and music sources for

extensions through MMC 308. If external music source will be used, select this

option through MMC 861 (default is internal).

7-8

OfficeServ 7100 Installation Manual

7.2.2 Connecting External/Additional Page Equipment

Instead of an internal speaker, external broadcasting equipment, such as amps or speakers,

and additional equipment that can broadcast page(ring) signals outside a building can be

connected to the OfficeServ 7100 system. Connect external/additional page equipment to

the MISC port of the MP10/MP11 board mounted on the OfficeServ 7100 system. The

power of the external/additional page equipment should be separately connected.

The OfficeServ 7100 system supports the channels for external broadcasting and one dry

contact. If a pair of External Page Equipment lines is connected to pin3 and pin6, Dry

Contact 1 lines is connected to pin1 and pin2, Dry Contact 2 lines is connected to pin7

and pin8 of the MISC port in MP10(MP11).

Dry Contact

(for Common bell)

External Page Equipment

Figure 7.11 Connecting External/Additional Page Equipment

Dry Contact

Dry Contact is a switch that can connect or cut the power or line to external

equipment.

7.2.3 Connecting Common Bell

Common Bell is the ring type. So, when a ring is received through an extension of a group,

all extensions of the group also receive the ring.

To use common bell, connect the common bell to the MISC port mounted on the

OfficeServ system. The OfficeServ 7100 system supports only one dry contact for the

common bell.

Dry contact

(For common bell)

Figure 7.12 Connecting Common Bells

7-9

CHAPTER 7. Ошибка! Стиль не определен.

7.2.4 Changing System Setting

Since the OfficeServ 7100 system is equipped with the web server of WebMMC, it

supports the remote access through the network. The system administrator can change the

system setting after getting access to WebMMC by using a browser.

This section describes how to access the OfficeServ 7100 system.

If the in-housing network is established, connect LAN to the LAN port of the MCP board

and attempt the access in a client PC.

Setting Network parameter by using the MMC830 program

Set the network parameter of the OfficeServ 7100 system. For the setting value of the

network parameter, contact the network administrator.

1) Set the IP address of the OfficeServ 7100 system.

2) Set the subnet mask of the OfficeServ 7100 system.

3) Set the gateway address of the OfficeServ 7100 system.

4) Reset the board.

About the board reset

To apply new setting, the board should be reset.

7-10

OfficeServ 7100 Installation Manual

Getting access to WebMMC from a client PC

1) Execute your browser.(Internet Explorer 5.0 or higher)

2) Access WebMMC by using the LAN IP address.

Access address: http://[System LAN IP Address]

Figure 7.13 WebMMC Initial Screen

3) Enter your ID and password on the WebMMC initial screen, and click the [OK] button

for login.

7.2.5 Connecting SMDR

The Station Message Detail Recording(SMDR) computer is used for recording call

information and for calculating phone bills or displaying various analysis data based on the

call data provided by the system.

The SMDR computer can be connected via the LAN port of the 4SWM board or the

MP10/11 board built in the OfficeServ 7100 system.

SMDR system specification is as follows:

Table 7.2 Specification of the SMDR System