Omnitron Systems Technology Mah 200 User Manual

CODE READER  
MAH 200  
Quickstart Guide  
QUICKSTART GUIDE  
CODE READER MAH 200  
GENERAL INFORMATION  
This documentation has been created with great care.  
Nevertheless, progress in technology can cause changes of the product leading to deviations between  
this documentation and the actual product.  
The content of this documentation, the technical data and the specifications of the product may be  
changed without prior notice.  
No part of this documentation may be copied, reprinted or translated without written permission of  
the OmnitronAG.  
This technical manual serves to assist the user and does not replace adequate education  
which is offered by the Omnitron AG and qualified partners.  
OmnitronAktiengesellschaft für  
Optoelektronische Geräte  
Im Leuschnerpark 4  
D-64347 Griesheim  
fon +49 (0) 6155 605314  
fax +49 (0) 6155 8740-12  
ii  
QUICKSTART GUIDE  
CODE READER MAH 200  
TABLE OF CONTENTS  
GENERAL INFORMATION ................................................................................................ ii  
TABLE OF CONTENTS ...................................................................................................... iii  
INTRODUCTION................................................................................................................ 1-1  
TARGETING AND READING TECHNIQUES ............................................................. 1-2  
VARIOUS PROGRAMMING CODES ............................................................................. 1-4  
Reader-ID and Firmware..................................................................................................... 1-4  
Reseting and storing of reader configurations...................................................................... 1-4  
TECHNICAL DATA ........................................................................................................... 1-5  
Overview............................................................................................................................. 1-5  
Decode zone........................................................................................................................ 1-6  
SYSTEM REQUIREMENTS ............................................................................................. 1-7  
Operating System ................................................................................................................ 1-7  
Interfaces ............................................................................................................................. 1-7  
Bluetooth ............................................................................................................................. 1-7  
ORDER INFORMATION ................................................................................................... 1-8  
APPENDIX A – USB INTERFACE ................................................................................ A-1  
APPENDIX B – RS – 232 INTERFACE ......................................................................... B-2  
APPENDIX C – PS 2 INTERFACE ................................................................................ C-3  
APPENDIX D – BLUETOOTH RADIO OVERVIEW ................................................. D-4  
Bluetooth Radio Overview................................................................................................. D-4  
Bluetooth Radio Overview (con‘t) ..................................................................................... D-5  
iii  
QUICKSTART GUIDE  
CODE READER MAH 200  
INTRODUCTION  
MAH 200 is a revolutionary new, bar MAH 200. Developed to be the first universal reader, no  
other single device performs as many functions. With a cost of ownership far less than  
comparable systems, the MAH 200 incorporates a unique dual path optical system, a 1.3 million  
pixel CMOS sensor, and a 400 MHz processor. This combination has created a reading system  
that supports:  
• High density matrix codes and larger low density linear codes  
• Superior working range  
• High-speed omni-directional decoding  
• Cordless and cabled interfaces  
The MAH 200 sets a new benchmark for size and weight. It is smaller and lighter than  
comparable systems yet can withstand multiple drops to concrete. It is the only product  
available in handheld, gun handle, and presentation stand form factors with cabled,  
batch and cordless versions. The cordless version utilizes the latest Bluetooth™ class 1 radio  
with a 300 foot operating range. The MAH 200 is rugged and lightweight and the cordless  
version will operate for more than a complete shift at the highest use rate. The MAH 200  
performs more than 3000 reads and transmits from a single battery charge. The MAH 200 will  
automatically discriminate between all major 2-D matrix and linear bar code symbologies and  
features a timestamp feature for logging data.  
Whether you need a small, palm-held device or a traditional gun, MAH 200 was specifically  
developed so users may easily choose the device that best meets their needs.  
OmnitronAG  
Im Leuschnerpark 4  
D-64347 Griesheim  
fon +49 (0) 6155 605314  
fax +49 (0) 6155 8740-12  
If you need technical support please contact us under the above mentioned adresse.  
1-1  
QUICKSTART GUIDE  
CODE READER MAH 200  
TARGETING AND READING TECHNIQUES  
The MAH 200 utilizes digital camera technology to take a pictures of a symbol. Once an image is  
captured, the MAH 200 utilizes advanced decoding algorithms to extract data from the captured  
image.  
The MAH 200 is available as a palm-held unit or users may purchase a clip-on pistol-grip  
handle.  
The palm held unit features left and right triggers. These triggers may be programmed to  
perform various features. The reader is shipped with the left trigger and right trigger functioning  
as a decode symbol command.  
The clip-on pistol-grip handle features a trigger on the handle. The two triggers on the top  
of the unit also work when the handle is attached.  
The MAH 200 – with and without gun handle.  
To read a symbol with the MAH 200:  
1. The MAH 200 features omnidirectional decoding. Center the symbol in any orientation  
within the laser dot aiming pattern.  
Laser targeting beam pointed directly into the center of this symbol.  
1-2  
QUICKSTART GUIDE  
CODE READER MAH 200  
NOTE: The MAH 200 can read a symbol that is not centered however, the MAH 200 performs  
best when a code is centered. If two (2) bar codes are with the imagers decode zone, the  
MAH 200 will decode the symbol closest to the center of the aiming dot.  
2. The MAH 200 was developed to decode both very small 2-dimensional symbols and larger  
1- dimensional symbols. The unit features two imagers to create an innovative dual decode  
zone. The MAH 200 features a high speed processor and DECODES BOTH ZONES  
SIMULTANEOUSLY. The unit has one imager focused on a near-field for smaller codes  
(optimal focal point is 4 inches) and one imager focused on a far-field for larger codes  
(optimal focal point 9 inches). To read smaller symbols move the MAH 200 closer to the  
symbol. To read larger symbols move the unit farther away from the symbol. The entire  
MAH 200 decode zone varies between two (2”) and sixteen (16+”) or more inches.  
3. Hold the MAH 200 still - DO NOT SWIPE OR MOVE THE READER. Press the trigger  
until the MAH 200 beeps, indicating the bar code has been successfully decoded.  
1-3  
QUICKSTART GUIDE  
CODE READER MAH 200  
VARIOUS PROGRAMMING CODES  
Reader-ID and Firmware  
Ausgabe der Leser-ID und der Firmware  
Reseting and storing of reader configurations  
Clear All Stored Data  
Clear All CodeXML Rules  
Reset to USB Factory Defaults  
Reset to RS-232  
Factory Defaults  
Reset to PS2 Factory Defaults Save Settings  
1-4  
QUICKSTART GUIDE  
CODE READER MAH 200  
TECHNICAL DATA  
Overview  
Symbologies  
MaxiCode, PDF417, Data Matrix, QR Code,MicroPDF 417, GoCode, UCC Composite, Aztec Code,  
Code 39, Code 128, UPC, EAN, JAN, Int 2 of 5, Codabar, Code 93, UCC RSS, POSTNET, PLANET,  
Japanese Post, Australia Post, Royal Mail, RM4SCC, KIX Code  
Sensor  
CMOS (1024 x 1280 = 1,3 Mio Pixel)  
Optical Resolution  
Near- Field 1024 x 640 Pixel und Far Field 1024 x 640 Pixel  
Interfaces  
USB (standard), RS-232, PS 2, Bluetooth Class 1 Radio  
Dimensions  
33 x 109 x 46 mm  
Weight  
51 g (without cabel)  
Ambient Temperature  
0° C bis 40°C  
1-5  
QUICKSTART GUIDE  
CODE READER MAH 200  
Decode zone  
1-6  
QUICKSTART GUIDE  
CODE READER MAH 200  
SYSTEM REQUIREMENTS  
Operating System  
Windows 98 (Version 2), ME, 2000, XP  
Interfaces  
USB or RS-232 / seriell / PS 2  
Bluetooth  
The MAH 200 supports the seriell communication profil.  
1-7  
QUICKSTART GUIDE  
CODE READER MAH 200  
ORDER INFORMATIONEN  
Part-Nr.  
182028  
182029  
Description  
MAH 200 Handheld reader with 1.80m cable for USB interface  
MAH 200 Handheld reader with gun format handle, 1.80m cable  
for USB interface  
182030  
182031  
182032  
MAH 200 Handheld reader with batch store, 1.80m cable for  
USB interface and battery LiON 1300 mAH  
MAH 200 Handheld reader with batch store, gun format hand-  
le, 1.80m cable for USB interface and battery LiON 1300 mAH  
MAH 200 Handheld reader, cordless, 1.80m cable for USB  
Interface, battery LiON 1300 mAH and Bluetooth Radio Module  
Class 1  
182033  
MAH 200 Handheld reader, cordless, gun format handle, 1.80m  
cable for USB Interface, battery LiON 1300 mAH and Bluetooth  
Radio Module Class 1  
182034  
182035  
MAH 200 Handheld reader with 2,40m cable for PS2 interface  
MAH 200 Handheld reader with gun format handle, 2,40m cable  
for PS2 interface  
Options/ Spare parts  
182036  
Options/ Spare parts  
MAH 200 Handheld reader only  
Gun format handle for MAH 200  
Cable 1,80m for USB Interface  
Cable 2.40m (with RS232 Interface and power supply connection)  
Cable 1,80m for PS2 Interface  
Battery LiON 1300 mAH  
182037  
182038  
182039  
182040  
182041  
182042  
Battery LiON 1800 mAH  
182043  
Bluetooth Module  
1-8  
QUICKSTART GUIDE  
CODE READER MAH 200  
Part-Nr.  
Options/ Spare parts  
182044  
Description  
Options/ Spare parts  
Power Supply RS232  
Battery Charger incl. power supply  
182045  
182046  
Code Router Software (Bluetooth Edition Windows)  
Bracket for MAH 200  
182047  
182048  
Bluetooth modem incl. RS 232 cable and power supply  
Cable 2.40m for RS232 Interface incl. power supply  
Bluetooth USB Dongle, Class 1, 100m, Quick Connect Label  
Bluetooth modem incl. PS2 Cable  
182049  
182050  
184285  
1-9  
QUICKSTART GUIDE  
CODE READER MAH 200  
APPENDIX A – USB INTERFACE  
Installation Guide  
To connect the MAH 200 to your host computer via  
USB interface:  
1. Make sure the USB cable is sufficiently attached to your MAH 200 unit  
(figure 2.1).  
2. You DO NOT need to power off your host computer (figure 2.2). The MAH 200 with USB  
interface can be plugged into any host while the computer is powered up.  
3. Connect the USB interface cable to the host (figure 2.3). If you are unsure of the proper location  
to connect the USB cable please consult the manual of your host computer.  
4. The USB interface does not require additional power supply. If you are using the 1300 mA or  
1800 mA battery for batch mode, the MAH 200 will automatically recharge the battery whenever  
the unit is a attached to a host that is powered up.  
5. The MAH 200 will power on automatically.  
6. Scan the USB Keyboard Mode code to then the Save Setting code to configure reader:  
USB Keyboard Mode (Default)  
Save Settings  
Note: For more information on other USB modes, please see section 5.2 of the MAH 200 Users  
Manual  
7. Your MAH 200 unit should be ready for use. Open the application (any Windows based  
application that accepts Keystroke data – e.g. Notepad) you wish to send data and begin scanning.  
A -1  
QUICKSTART GUIDE  
CODE READER MAH 200  
APPENDIX B – RS-232 INTERFACE  
Installation Guide  
To connect the MAH 200 to your host computer via RS-232 interface:  
1. Make sure the RS-232 cable is sufficiently attached to your MAH 200 unit (figure 2.4).  
2. Connect the RS-232 interface cable to your host computer (figure 2.5). If you are unsure of the  
proper location to connect the RS-232 cable please consult the manual of your host computer.  
3. The RS-232 interface should have come with a power supply. Plug the power supply adapter  
into the RS-232 interface cable (figure 2.6) and then plug the power adapter into a wall socket  
(figure 2.7).The RS-232 interface does not require additional power. However, if you are using  
the RS-232 interface and utilizing Batch functionality, please read the Important Note in section  
7.1. If you are using the 1300 mA or 1800 mA battery for batch mode, the MAH 200 will  
recharge the battery whenever the unit is a attached to a RS-232 cable that is plugged into a wall  
socket.  
4. The MAH 200 will power on automatically.  
5. Scan the RS-232 One Way Mode code then the Save Settings code to configure reader:  
RS-232 One Way Mode  
Save Settings  
Note: All Baud Rate, Parity, Stop Bit and Data Bit settings can be found in Chapter 5 of the  
MAH 200 User Manual.  
6.Your MAH 200 unit should be ready for use. Open the application (any Serial  
Communications Software – e.g. Hyper Terminal) you wish to send data and begin scanning.  
Default Settings  
Baud Rate  
Stop Bits  
Data Bits  
Parity  
57600  
1
8
None  
B -2  
QUICKSTART GUIDE  
CODE READER MAH 200  
APPENDIX C – PS 2 INTERFACE  
Installation Guide  
1. Power off the host computer.  
2. Attach the end of the PS2 cable with the single connector  
to the MAH 200.  
3. If external keyboard exists, unattach your keyboard from the host and connect the appropriate  
connector to the PS2 cable  
.
4. Connect the other connector to host computer into keyboard port The MAH 200 is powered  
by the PS2 port and does not require a power supply.  
5. Set the MAH 200 to PS2 mode by scanning the code below, then scan the Save Settings code:  
PS2 Mode  
Save Settings  
6. Your MAH 200 unit is now ready. Open the appropriate application (any Windows based  
application that accepts Keystroke data – e.g. Notepad) and begin scanning data.  
Upgrade Note: The PS2 model does not work with a USB cable. If you are upgrading the  
firmware you must use an RS-232 cable.  
WARNING: Code does not recommend using Batch or Bluetooth Radio modes with the PS2  
interface because you need to disconnect the MAH 200 and the keyboard and this may result in  
the host computer freezing and requiring you to reboot.  
C -3  
QUICKSTART GUIDE  
CODE READER MAH 200  
APPENDIX D – BLUETOOTH RADIO OVERVIEW  
Overview  
This version of the MAH 200 features a Bluetooth® wireless radio. The radio allows for point to  
point wireless communication with other Bluetooth devices that support serial port protocol (SPP).  
The following guide will give you general instructions on connecting your MAH 200 to a desktop  
or laptop computer with a Bluetooth radio.  
Connecting With A Quick Connect Code  
The easiest way to connect to a Bluetooth device is to visit Code’s web site and create a Quick  
Connect Code that is specific to your device (figure 2.9). This code will link your MAH 200  
directly to the desired Bluetooth device. To create a Quick Connect Code, you will need to know  
the Bluetooth address (often referred to as the BD_ADDR) of that device. You can usually find  
the 12-character Bluetooth address somewhere on the device near the device’s serial number (see  
figure 2.10).  
If you purchased a CodeXML Bluetooth Modem or a Belkin® Bluetooth adapter from Omnitron  
from an authorized distributor, a Quick Connect Code is included. The CodeXML Bluetooth  
modem is a simple hardware solution for customers who wish to enjoy the benefits of cordless  
data collection without modifying existing applications or installing software. Please contact the  
Omnitron Support Team for more information.  
Note:While installing the Bluetooth Configuration Manager software that came with the adapter,  
make sure to take note of the Virtual COM Port the software has assigned for the adapter (e.g.  
COM 10). This is the COM Port your MAH 200 will connect through.  
Scan the RF One Way - Max Range code below then the Quick Connect Code and your MAH  
200 will automatically connect.You should also scan the Save Settings code if you want to save  
these settings (Note: If the MAH 200 unit powers off without scanning the Save Settings code,  
you will lose your settings).  
RF One Way Mode (Max Range)  
Quick Connect  
Save Settings  
D -4  
QUICKSTART GUIDE  
CODE READER MAH 200  
APPENDIX D – BLUETOOTH RADIO OVERVIEW (CON‘T)  
Radio Range and Transferring Data  
The MAH 200 radio is a Class 1 device. If connected to another Class 1 device the unit has  
roughly a 300 foot line of sight operating range. If connecting to a Class 2 or Class 3 device, the  
operating range may drop to match the lower range. Once a unit is connected, the application  
software on the host must be open to receive data.  
When the MAH 200 detects the radio is out of range, the MAH 200 will store data on the reader’s  
non volatile memory. The reader will continue to try and send data until radio is back in range.  
Once the data is sent the data will be erased from the units memory. If the radio cannot connect in  
90 seconds, it will give an error beep. The reader will continue to try and connect until it has  
reached the programmable radio time out setting.  
The MAH 200 Bluetooth protocol allows for two (2) forms of communication:  
1. One Way Mode - Defined as one way communication between the reader and host. One Way  
mode only recommended when connecting to a device well within itse specified range or if  
connected to a device without an operating system (i.e. printer). There are two settings in this  
mode:  
• Max Range (Default) - Greater range but data reliability is lower  
• Max Reliability - Limits range but reliability is improved  
RF One Way Mode (Max Range)  
RF One Way Mode (Max Reliability)  
Note: While robust, One Way Mode doesn’t guarantee data integrity and you may have data  
loss.  
2. RF Two Way Mode - This is two way communication between the host and reader. This  
requires the implementation of software at the application level.* The reader receives confirmation  
via packet protocol verification and is 100% reliable. Data will be automatically retransmitted if  
necessary.  
RF Two Way Mode  
* Note: You will need to install application software that supports packet communication to  
operate in RF Two Way Mode. Omnitron offers a Windows or Pocket PC version of software  
called CodeXML Router - Bluetooth Edition (BE) that provides for end-to-end Bluetooth  
handshakes that eliminate out-of-range data loss. CodeXML Router - BE also offers Bluetooth  
to keyboard wedge communication for applications that require keyboard port input.  
If you are using the CodeXMLBluetooth modem, you must use RF Two Way Mode.  
D -5  
QUICKSTART GUIDE  
CODE READER MAH 200  
APPENDIX D – BLUETOOTH RADIO OVERVIEW (CON‘T)  
Save Settings  
Scan the code below to make the RF settings permanent on the reader:  
Save Settings  
Disconnecting from the Device  
You may force disconnection by reading the disconnect code below (The MAH 200 may not  
appear disconnected in the slave Bluetooth connection manager for 10 – 15 seconds after the  
command is issued). The MAH 200 will also disconnect after 90 seconds of inactivity (Note:You  
may change the radio frequency sleep time out setting however, it may reduce battery life).  
Disconnect  
Reconnecting to the Device  
If the device is saved in RF mode it will automatically reconnect when:  
1. MAH 200 is powered up  
2. MAH 200 wakes from sleep mode  
3. MAH 200 reads another code  
D -6  

Sears 20071225 User Manual
Philips Ss191p User Manual
Panasonic Ey0005 User Manual
Omega Flowmeter Fl 1500a User Manual
Mitsubishi Electronics Mr Slim Msy A24na User Manual
JVC AV 27D104 User Manual
HITACHI 50PD960DTA User Manual
HITACHI 26LD8000TA 2 User Manual
HAYWARD MAX PLO XL User Manual
DELVCAM DELV SDI IP User Manual