Pacemark 4410
Setup Guide
59290803
Overview
Conventions Used in this Setup Guide ................................................... 2
Safety .................................................................................................3
Introduction ...................................................................................... 5
Pacemark 4410 Features ......................................................................... 5
Select a Location .................................................................................... 6
Unpacking .........................................................................................7
Getting Started ........................................................................................ 7
Documentation Provided ........................................................................ 8
Installing the Printer .........................................................................9
Getting to Know the Pacemark 4410...................................................... 9
Installation ............................................................................................ 10
Remove the Shipping Restraints ........................................................ 10
Install the Ribbon Cartridge ............................................................... 12
Install the Paper Guide ....................................................................... 15
Connect to the Computer/Network..................................................... 16
Connecting the Parallel Port............................................................. 16
Connecting the Serial Port................................................................ 17
Connecting the Ethernet Port ........................................................... 18
Connect to Power ............................................................................... 20
Load Paper.......................................................................................... 21
Front Feed Continuous Forms .......................................................... 21
Rear Feed Continuous Forms ........................................................... 26
Switching Paper Paths ........................................................................ 30
Run the Self Tests ............................................................................... 31
Font Sample Test .............................................................................. 31
Rolling ASCII Test ........................................................................... 32
Select an Emulation .............................................................................. 33
Installing the Software .................................................................. 35
The Pacemark 4410 CD........................................................................ 35
Printer Drivers .................................................................................... 35
On-Line Registration Program ........................................................... 35
User’s Guide ....................................................................................... 36
Pacemark 4410 Setup Guide
English-1
Installation for Windows 2000 ............................................................. 36
Installation for Windows 95/98 ............................................................ 40
Installation for Windows NT 4.0 .......................................................... 43
Installation for Windows 3.1x .............................................................. 46
Front Panel Overview .................................................................... 49
Print Mode ............................................................................................ 49
Menu Mode........................................................................................... 51
Top of Form (TOF) ............................................................................... 52
Printer Features .............................................................................. 55
Preset Menu Configurations ................................................................. 55
Tear Feature .......................................................................................... 56
Forms Tear-Off Feature ........................................................................ 57
Paper Park Feature................................................................................ 58
Specifications ................................................................................. 59
Limited Warranty ........................................................................... 61
FCC/IC/CE Statements .................................................................... 65
Material Safety Data Sheet............................................................ 67
Conventions Used in this Setup Guide
Notes
Notes are set in regular type and contain general information.
Caution!
Cautions are set in bold italics and contain information
regarding actions which could potentially cause personal
injury or damage to the printer.
Important!
Important information is set in italics.
E-2
Pacemark 4410 Setup Guide
Safety
Your OKI printer has been carefully designed to give you years of safe,
reliable performance. As with all electrical equipment, there are a few
basic precautions you should take to avoid hurting yourself or
damaging the printer:
• Read the setup and operating instructions in this manual carefully. Be
sure to save it for future reference.
• Read and follow all warning and instruction labels on the printer
itself.
• Unplug the printer before you clean it. Use only a damp cloth; do not
use liquid or aerosol cleaners.
• Place your printer on a firm, solid surface. If you put in on something
unsteady, it might fall and be damaged; if you place it on a soft
surface, such as a rug, sofa, or bed, the vents may be blocked, causing
it to overheat.
• To protect your printer from overheating, make sure no openings on
the printer are blocked. Do not put the printer on or near a heat
source, such as a radiator or heat register. If you put the printer in any
kind of enclosure, make sure it is well ventilated.
• The printhead can get quite hot when it has been printing for a length
of time. Do not touch the printhead until it has had a chance to cool
off.
• Do not use your printer near water, or spill liquid of any kind into it.
• Be certain that your power source matches the rating listed on the
back of the printer. If you are not sure, check with your dealer or with
your local power company.
• Your printer has a grounded, 3-prong plug as a safety feature, and it
will only fit into a grounded outlet. If you can not plug it in, chances
are that you have an older, non-grounded outlet; contact an electrician
to have it replaced with a grounded outlet. Do not use an adapter to
defeat the grounding.
• The printer must be installed near a power outlet which will remain
easily accessible.
Pacemark 4410 Setup Guide
E-3
• To avoid damaging the power cord, do not put anything on it or place
it where it will be walked on. If the cord becomes damaged or frayed,
replace it immediately.
• If you’re using an extension cord or power strip with the printer,
make sure that the total of the amperes required by all the equipment
on the extension is less than the extension’s rating. Generally, the total
ratings of all equipment plugged into any one power line should not
exceed 15 amperes. Don’t exceed this unless you know that the power
line your equipment is plugged into has a rating above 15 amperes.
• Do not poke anything into the ventilation slots on the sides of the
printer; you could get a shock or cause a fire.
• Aside from the routine maintenance described in Section 2 of the on-
line Pacemark 4410 User’s Guide, don’t try to service the printer
yourself; opening the cover may expose you to shocks or other
hazards. Don’t make any adjustments other than those outlined in the
Pacemark 4410 User’s Guide - you might cause damage requiring
extensive repair work.
• If anything happens that indicates that your printer is not working
properly or has been damaged, unplug it immediately and follow the
procedures in Section 4 of your on-line Pacemark 4410 User’s Guide
for having your printer serviced. These are some of the things to look
for:
- The power cord or plug is frayed or damaged.
- Liquid has been spilled into the housing, or the printer has been
exposed to water.
- The printer has been dropped or its cabinet has been damaged.
- The printer doesn’t function normally when you’re following the
operating instructions.
E-4
Pacemark 4410 Setup Guide
Introduction
Pacemark 4410 Features
• Reliable, heavy-duty
- Reliability: 15,000 hours MTBF
- Duty Cycle: 35,000 pages/month
• Fast
- 300 lines per minute
- 1066 cps in High Speed Draft mode
• Capable of handling 10-part carbonless forms up to 0.03 inch
(0.79 mm) thick
• Rugged, long-life printhead (400 million characters)
• Wide, 136-column format
• Network capable
• Software selectable or auto-switched rear- and front-feed paper paths
• Two user-settable menu configurations
Pacemark 4410 Setup Guide
E-5
Select a Location
• Firm, level surface capable of supporting approximately 95 lbs.
(43 kg)
• Clearance to open cover
• At least four inches (102 mm) additional clearance on both sides for
adequate ventilation
• Nearby power source
• Room temperature: 41 to 95°F (5 to 35°C)
• Relative humidity: 20 to 80%
• Away from direct sunlight
E-6
Pacemark 4410 Setup Guide
Unpacking
Getting Started
Caution! The Pacemark 4410 printer weighs approximately
95 lbs. (43 kg). Be very careful to take appropriate
precautions when lifting it. We recommend that at least two
people participate when lifting the printer.
Check the contents:
1
2
3
4
5
1 Printer
2 Ribbon Cartridge
3 Paper Guide
4 Power Cord
5 Cable (only included with 4410s which have Print Server pre-installed)
If anything is missing or damaged, contact your dealer immediately.
The printer interface cable is not supplied.
Pacemark 4410 Setup Guide
E-7
Documentation Provided
Setup Guide
The document you’re holding.
OKIcare™ Brochure
This brochure explains the Pacemark 4410 service enhancement
programs available in the U.S. and Canada.
On-line User’s Guide
In addition to the printer drivers, the Pacemark 4410 CD contains
• Adobe® Acrobat Reader® 3.0 software
• User’s Guide Acrobat® file:
Recommended minimum requirements for viewing the on-line
User’s Guide:
desktop area = 800 x 600 pixels
color palette = 256 colors.
User’s Guide Contents:
– The Front Panel
– Maintenance
– Troubleshooting
– Service Information
– Specifications
– Interfacing
– Command Summary
– Hex Dump Mode
– Character Sets
– FCC/IC/CE Statements
– Warranty
You can print any portion or all of the User’s Guide from Adobe
Acrobat Reader.
If you would like a printed copy of the Pacemark 4410 User’s Guide,
see the form at the back of this Setup Guide.
E-8
Pacemark 4410 Setup Guide
Installing
the Printer
Getting to Know the Pacemark 4410
Front View
Tear Bar Cover
Rear-Feed Access Cover
Printhead Access Cover
Control Panel
On/Off
Switch
Front Access Door
Tear Bar Cover
Rear View
Rear-Feed Access Cover
Serial Port
Back
Access
Door
Port
Access
Cover
Parallel
Port
Power
Cord Port
Network/Option Slot
Pacemark 4410 Setup Guide
E-9
Installation
Remove the Shipping Restraints
Save the shipping restraints and packing materials in case
you ever need to ship the printer.
1. Remove the pieces of shipping tape, then peel the protective plastic
film off the digital display.
2. Press on the area(s) marked “PUSH” and open the printhead access
cover.
3. Remove the printhead shipping restraint and its retaining screw. Be
sure to keep this restraint/screw: it is needed to lock the printhead in
place should you ever need to move or ship the printer.
E-10
Pacemark 4410 Setup Guide
4. Remove the red rubber shipping restraints (1) at either end.
1
5. Open the tear bar cover, remove the shipping restraint and close the
cover.
Caution! Avoid the sharp, serrated tear bar.
Pacemark 4410 Setup Guide
E-11
Install the Ribbon Cartridge
Prepare the Cartridge
1. Swing out the ribbon arms at either end of the cartridge until they
snap into place.
2. Push in on the white plastic ribbon restraint (1) at the right end of the
cartridge (this engages the ribbon take-up knob).
1
3. Pull out the red shipping restraint (1) and turn the blue knob (2)
counterclockwise (in the direction of the molded arrows) to take up
any excess slack in the ribbon.
2
1
E-12
Pacemark 4410 Setup Guide
Load the Cartridge
1. Move the printhead to the ribbon loading area (1).
Caution! Make sure the printer is turned off before
proceeding.
1
2. Install the ribbon cartridge in the printer: place the ribbon arms (1)
over the metal tabs (2) at either end, then press down on the
cartridge.
1
2
2
1
2
Pacemark 4410 Setup Guide
E-13
3. Feed the ribbon behind the printhead (1), threading it around the
black guides (2) on either side of the printhead.
Be careful not to twist the ribbon: this can cause jams.
1
2
4. Turn the blue knob counter clockwise (in the direction of the
molded-on arrows) to take up any slack in the ribbon.
Caution! Do NOT turn the knob clockwise: this can cause
the ribbon to jam.
5. Close the printhead access cover.
E-14
Pacemark 4410 Setup Guide
Install the Paper Guide
Hold the paper guide as shown and place it in the slots on the back of
the printer.
Pacemark 4410 Setup Guide
E-15
Connect to the Computer/Network
Connecting the Parallel Port
The parallel port is a standard IEEE-1284-compatible,
36-pin port. It requires a shielded IEEE-1284-compatible,
bi-directional cable no longer than 6 ft. (1.8 m).
1. Open the port access cover.
2. Plug the interface cable into the parallel port and secure it with the
wire loops.
3. Close the port access cover, and attach the other end of the cable to
the computer and secure it with the screws.
Default settings for the parallel interface (see Section 1 of
your on-line Pacemark 4410 User’s Guide for information on
changing Menu settings):
I Prime = Buffer Print
Pin 18 = +5V
Auto Feed XT = Invalid (Epson FX emulation only)
BiDirection = Enable
E-16
Pacemark 4410 Setup Guide
Connecting the Serial Port
The serial port is a standard RS-232C, 25-pin port, with
selectable baud rates of up to 38.4 Kbps. It requires a
shielded RS-232C cable which is UL and CSA approved
and no more than 50 feet (15 m) in length.
1. Open the port access cover and plug the interface cable into the serial
port.
2. Secure the cable with the screws and close the port access cover.
3. Attach the other end of the cable to the computer and secure it with
the screws.
Default menu settings for the serial interface (see Section 1 of
your on-line Pacemark 4410 User’s Guide for information on
changing Menu settings):
Parity = None
Baud Rate = 9600 BPS
DSR Signal = Valid
DTR Signal = Ready on Power Up
Busy Time = 200 mS
# Serial Bits = 8 Bits
Protocol = Ready/Busy
Diagnostic Test = No
Busy Line = SSD-
Pacemark 4410 Setup Guide
E-17
Connecting the Ethernet® Port
(for Pacemark 4410 with Print Server Pre-Installed)
The installed print server is EtherNet 10/100BaseT.
The Ethernet port requires a cable with two twisted-wire
pairs and an RJ45 plug for connection to the network. See
the OkiLAN 6100e User’s Manual included with your
printer for additional information.
1. Open the port access cover.
2. Plug one end of the short cable included with the printer into the
network board and the other end of the cable into the parallel port.
E-18
Pacemark 4410 Setup Guide
3. Secure the cable at both ends, then close the port access cover.
4. Plug the RJ45 connector into the EtherNet connector on the OkiLAN
board, then connect the opposite end of the cable into the network.
Pacemark 4410 Setup Guide
E-19
Connect to Power
1. Attach the power cord to the back of the printer.
2. Plug the opposite end into a suitable, grounded outlet.
E-20
Pacemark 4410 Setup Guide
Load Paper
Front Feed Continuous Forms
Paper Specifications: Front Feed
Maximum thickness: 0.031 inches (0.79 mm)
Type
Weight
12 to 24 lb. (45 to 90 g/m2) 3* to 16.5 inches (76 to 419 mm)
9 to 11 lb. (34 to 41 g/m2)
3* to 16.5 inches (76 to 419 mm)
Width
Single Part
Carbonless
(1 + 9 max.)
Interleaf
(1 + 6 max)
9 to 14 lb. (34 to 52.5 g/m2) 3* to 16.5 inches (76 to 419 mm)
9 lb. (34 g/m2) carbon
Labels
0.011 inch (0.28 mm) thick 3¼ to 15 inches (83 to 381 mm)
Envelopes
Card Stock
24 lb. (90 g/m2) max.
100 lb. (375 g/m2) max.
3 to 10 inches (76 to 254 mm)
3 to 8 inches (76 to 203 mm)
* For paper widths less than 5 inches (127 mm), remove the support between the
tractors.
When using paper which is thicker than 7-part carbonless or
its equivalent, you must enter the Menu mode, then go to the
Impact Mode item in the Set-Up group and select High
Impact Copy as the setting.
To load front-feed continuous forms:
Preparation
1. Position the printer at the front edge of the support (this promotes the
unrestricted flow of paper into the printer), then place a stack of
continuous forms below the printer. Recommended height of printer
support, 29.5 inches (750 mm).
Pacemark 4410 Setup Guide
E-21
2. Pull the front access door out and lift it up into the open position.
Lock Lever
Pins
Tractor Pin Cover
3. Pull the lock levers forward to unlock the tractors, and position the
tractors to roughly fit the width of the continuous forms you will be
using.
The movement of the left tractor is limited to ensure that the
paper covers the paper-out sensor.
E-22
Pacemark 4410 Setup Guide
4. Center the supports between the tractors.
Left Tractor
1. Open the left tractor pin cover, place the paper holes on the pins, then
close the cover.
2. Move the left tractor to align the edge of the paper with the
appropriate reference mark (1: this sets the print indent from the
paper edge at 0 to 1.5 inches in 0.1-inch increments), then push the
lock lever back
1
Pacemark 4410 Setup Guide
E-23
Right Tractor
1. Open the right tractor pin cover, place the paper holes over the pins
and close the cover.
2. Fine tune the position of the right tractor to center the holes in the
paper on the pins of both tractors, then push the lock lever back.
Finish Up
1. Make sure that the feed stack of paper is directly aligned (left-right)
with its entry point into the tractors: this will promote a smooth flow
of paper into the printer.
2. Close the front access door.
3. Press FF/LOAD to load the paper into the print path.
E-24
Pacemark 4410 Setup Guide
The printer is set to a default front-feed paper width of 13.6
inches (136 columns). If you are using 9-inch paper, you
must enter the printer menu and change the setting to 8
inches (80 columns) to avoid printing on the platen and
damaging the printhead. Other paper widths must be set
using your software application.
To change the menu setting to 8 inches, turn the printer on,
then:
a. Press MENU.
b. Press GROUP until Front Feed appears on the display.
c. Press ITEM until Page Width appears on the display.
d. Press OPTION once to switch to the 8-inch setting.
An asterisk (*) appears next to the setting.
e. Press STORE to save the 8-inch setting.
f. Press MENU to exit the menu mode and save the new
setting.
The Top of Form (TOF) for the front feed paper path is set at the
factory to 0.35 inch (9 mm) down from the top of the page. If this
setting does not suit your application, you will need to set the Top of
Form: see “Setting Top of Form” in the Front Panel Overview section
of this Setup Guide.
Pacemark 4410 Setup Guide
E-25
Rear Feed Continuous Forms
Paper Specifications: Rear Feed
Maximum thickness: 0.014 inch (0.36 mm)
Type
Weight
12 to 24 lb. (45 to 90 g/m2) 3* to 16.5 inches (76 to 419 mm)
9 to 11 lb. (34 to 41 g/m2)
3* to 16.5 inches (76 to 419 mm)
Width
Single Part
Carbonless
(1 + 5 max.)
Interleaf
(1 + 3 max)
9 to 14 lb. (34 to 52.5 g/m2) 3* to 16.5 inches (76 to 419 mm)
9 lb. (34 g/m2) carbon
* For paper widths less than 4 inches (102 mm), remove the support between the
tractors.
When using paper which is thicker than 7-part carbonless or
its equivalent, you must enter the Menu mode, then go to the
Impact Mode item in the Set-Up group and select High
Impact Copy as the setting.
To load rear-feed paper:
Preparation
1. Position the printer at the rear edge of the support (this promotes the
unrestricted flow of paper into the printer), then place a stack of
continuous forms below the printer. Recommended height of printer
support, 29.5 inches (750 mm).
E-26
Pacemark 4410 Setup Guide
2. Push on the rear-feed access cover tabs and push the cover back, then
push on the back access door to release it.
Lock Lever
Pins
Tractor Pin Cover
3. Pull the lock levers forward to unlock the tractors, and position the
tractors to roughly fit the width of the continuous forms you will be
using.
The movement of the right tractor (as viewed from the back of
the printer) is limited to ensure that the paper covers the
paper-out sensor.
Pacemark 4410 Setup Guide
E-27
4. Center the support between the tractors, then position the paper guide
(1) over the support (2).
1
2
Right Tractor (viewed from the back of the printer)
1. Open the tractor pin cover, place the paper holes on the pins, then
close the cover.
2. Move the tractor to align the edge of the paper with the appropriate
reference mark (1: this sets the print indent from the paper edge at 0
to 1.5 inches in 0.1-inch increments), then push the lock lever back.
1
E-28
Pacemark 4410 Setup Guide
Left Tractor (viewed from the back of the printer)
1. Open the tractor cover, place the paper holes over the pins and close
the cover.
2. Fine tune the position of the right tractor to center the paper holes on
the pins of both tractors, then push the right lock lever back.
Finish Up
1. Make sure that the feed stack of paper is directly aligned (left-right)
with its entry point into the tractors: this will promote a smooth flow
of paper into the printer.
2. Close the rear-feed access cover and the back access door.
3. Press FF/LOAD to load the paper into the print path.
The printer is set to a default rear-feed paper width of 13.6
inches (136 columns). If you are using 9-inch paper, you
must enter the printer menu and change the setting to 8
inches (80 columns) to avoid printing on the platen and
Pacemark 4410 Setup Guide
E-29
damaging the printhead. Other paper widths must be set
using your software application.
To change the menu setting to 8 inches, turn the printer on,
then:
a. Press MENU.
b. Press GROUP until Rear Feed appears on the display.
c. Press ITEM until Page Width appears on the display.
d. Press OPTION once to switch to the 8-inch setting.
e. Press STORE to save the 8-inch setting.
f. Press MENU to exit the menu mode.
The Top of Form (TOF) for the rear feed paper path is set at the factory
to 0.35 inch (9 mm) down from the top of the page. If this setting does
not suit your application, you will need to set the Top of Form: see
“Setting Top of Form” in the Front Panel Overview section of this
Setup Guide.
Switching Paper Paths
The Pacemark 4410 is set at the factory for software control of the
paper path. You can enter the menu and change this so that the printer
will automatically switch to the alternate path when paper runs out. To
do this:
1. With the printer turned on, press MENU.
2. Press GROUP until Set-Up appears on the display.
3. Press SHIFT + ITEM until Auto Path appears on the display.
4. Press OPTION.
Valid will appear on the display.
5. Press STORE.
An asterisk (*) will appear next to Valid.
6. Press MENU to exit the menu and engage the settings.
E-30
Pacemark 4410 Setup Guide
Changing Paper Paths Manually
To change paper paths manually:
1. Press PARK.
The current paper retracts from the paper path.
2. Press PATH.
The alternate paper automatically loads into the paper path.
Run the Self Tests
Font Sample Test
To print a sample of the available fonts:
1. Make sure continuous form paper at least 8 inches wide is loaded and
that the printer is turned off.
2. Press and hold LF (1) while turning the printer on.
1
To stop the test before it is complete, press ON-LINE/RESET.
Pacemark 4410 Setup Guide
E-31
Rolling ASCII Test
To print a Rolling ASCII test:
1. Make sure that continuous form paper at least 9 inches wide is
loaded and that the printer is turned off.
Caution! If you have 9-inch paper loaded, be sure that the
Page Width menu setting for the paper path you are using
is changed from 13.6 inches to 8 inches before starting the
Rolling ASCII test. If you don’t, the printhead could be
damaged.
2. Press and hold PATH/TOF (1) while turning the printer on.
1
To stop the test, press ON-LINE/RESET.
E-32
Pacemark 4410 Setup Guide
Select an Emulation
Your printer has three emulations:
• Epson® FX
• IBM® Proprinter III (PPSII): the factory setting
• OKI® Microline® Standard
Changing Emulations
1. Press MENU to enter the menu mode.
The display reads
MENU GROUP
Printer Control
2. Press ITEM.
The display reads
Printer Control
Emulation Mode
3. Press OPTION.
The display reads
Emulation Mode
IBM-PPR
*
4. Press OPTION until the emulation you wish to use appears on the
second line of the display.
5. Press STORE to save the setting.
An asterisk (*) appears next to the setting.
6. Press MENU to exit the menu mode and save the new setting.
Pacemark 4410 Setup Guide
E-33
E-34
Pacemark 4410 Setup Guide
Installing
the Software
The Pacemark 4410 CD
Included on the Pacemark 4410 CD:
• Pacemark 4410 Printer Drivers
• Pacemark 4410 On-Line Registration Program
• Pacemark 4410 User’s Guide
• Adobe® Acrobat® Reader® Software
Printer Drivers
The Pacemark 4410 CD includes printer drivers for printing in the
following Windows® environments:
• Windows 2000
• Windows NT 4.0
• Windows 3.1x
• Windows 98 & 95
If you are using MS-DOS® or another non-Windows
operating system, select the IBM® Proprinter III or Epson®
FX printer driver in your software application.
On-Line Registration Program
You have several options for registering your printer:
• via modem, using the On-Line Registration program
• via fax, using the On-Line Registration program
• via mail, using the registration sheet included with the printer
If you wish to register through the Internet or by mail, you do not need
to load the On-Line Registration Program.
Pacemark 4410 Setup Guide
E-35
On-Line User’s Guide
The Pacemark 4410 CD also includes the OKI Pacemark 4410 On-Line
User’s Guide, as well as the Adobe Acrobat Reader software required to
view the User’s Guide.
When installed, the User’s Guide takes up approximately 73 MB of
space on your hard drive. If you prefer, you can view the User’s Guide
directly from the CD (\Manuals\English\e4410m.pdf).
Printing the OKI Pacemark 4410 On-Line User’s Guide
With the User’s Guide open in Acrobat Reader:
1. Select File, Print.
2. Choose the page(s) to print.
3. For Acrobat Reader 3:
a. Make sure Level 2 Only is selected under PostScript Options.
b. Click Setup and confirm the printer and its settings, then click OK.
For Acrobat Reader 4:
a. Make sure PostScript Level 2 is selected as the Print Method
under PostScript Options.
b. Click Properties and confirm the printer and its settings, then click
OK.
4. Click OK to print.
Installation for Windows 2000
To Install the Pacemark 4410 Printer Driver
(English Only) on Windows 2000
Minimum System Requirements for Windows 2000:
CPU: pentium, 133 MHz (350 MHz or higher recommended)
RAM: 64 MB
Empty hard disk space:
2 MB for use by print spooler
73 MB for User’s Guide (optional)
10 MB for Adobe Acrobat Reader Software (optional)
E-36
Pacemark 4410 Setup Guide
These instructions assume “D” is the location of your
CD-ROM drive.
Have your original Microsoft Windows 2000 CD handy. You
may be prompted for it during the installation.
1. Close any open applications, and make sure that the printer is
connected to the PC and turned on.
2. Insert the Pacemark 4410 CD in your CD-ROM drive.
3. Click Start Settings Printers.
4. Double-click Add Printer.
The Add Printer Wizard begins.
5. Follow the on-screen instructions.
6. When the Local or Network Printer window appears, make sure
“Automatically detect and install my Plug and Play printer” is not
selected. If it is selected, Windows 2000 will ignore the CD.
7. When you are prompted for the manufacturer and model of your
printer, click Have Disk.
8. Click Browse and go to your CD-ROM drive (usually D:),
9. Double-click Setup W2k English Driver, then double-click
Pm4410setup.
10. Click OK.
The printer name appears.
11. Double-click the printer name, then click Next and continue to
follow the on-screen prompts.
If the Digital Signature Not Found window appears
prompting you “Do you want to continue the installation?”,
click Yes and continue the installation.
If the Digital Signature Not Found window appears, but does
not offer you the option of continuing, check with your
System Administrator for further assistance.
12. Finish the installation following the instructions on your screen.
Pacemark 4410 Setup Guide
E-37
To Install the On-Line Registration Program
in Windows 2000
These instructions assume “D” is the location of your
CD-ROM drive.
1. Make sure all applications are closed and the Pacemark 4410 CD is
in your CD-ROM drive.
2. Click Start Run.
3. Type D:/install, and click OK.
4. Click the button beside On-Line Registration.
5. Follow the instructions on your screen.
To Run the On-Line Registration Program in Windows 2000
1. Click Start
Programs PM4410.
2. Click OKI Pacemark 4410 On-Line Registration.
3. Follow the instructions on your screen.
To Install the On-Line Pacemark 4410 User’s Guide
in Windows 2000
First, make sure Adobe Acrobat Reader is installed
To view the on-line Pacemark 4410 User’s Guide, you
must have Adobe Acrobat Reader version 4.05 installed on
your computer. If you do not already have Acrobat Reader
4.05 installed, it is provided on the Pacemark 4410 CD.
To install Acrobat Reader 4.05 in Windows 2000:
These instructions assume “D” is the location of your
CD-ROM drive.
1. Make sure all applications are closed and the Pacemark 4410 CD is
in your CD-ROM drive.
2. Click Start Run.
3. Type D:\Acrobat\Windows\English\W2k\ar405eng.exe.
4. Click OK.
5. Follow the instructions on your screen.
E-38
Pacemark 4410 Setup Guide
Next, install the On-Line User’s Guide in Windows 2000
These instructions assume “D” is the location of your
CD-ROM drive.
1. Make sure all applications are closed and the Pacemark 4410 CD is
in your CD-ROM drive.
2. Click Start Run.
3. Type D:/install, and click OK.
4. Click the button beside On-Line Manual.
5. Follow the instructions on your screen.
Viewing the On-Line Pacemark User’s Guide in Windows 2000
1. Click Start
Programs PM4410.
2. Click OKI Pacemark 4410 On-Line Manual.
To view the manual from the Pacemark 4410 CD, open
Acrobat Reader, click File Open, browse to the
Manuals\English directory on the CD, and double-click
e4410m.pdf .
Pacemark 4410 Setup Guide
E-39
Installation for Windows 95/98
To Install the Pacemark 4410 Printer Driver on
Windows 95/98
Minimum System Requirements for Windows 95/98:
CPU: i486DX, 66 MHz (90 MHz pentium recommended)
RAM: 8 MB (16 MB recommended)
Empty hard disk space:
2 MB for use by print spooler
73 MB for User’s Guide (optional)
10 MB for Adobe Acrobat Reader Software (optional)
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications and make sure that the printer is
connected to the PC and turned on.
2. Insert the Pacemark 4410 CD in your CD-ROM drive.
3. Click the Start Run.
4. Type D:/install and click OK.
5. Click the button beside Printer Driver.
6. Follow the instructions on your screen. When you are prompted for
the printer:
a. Click Have Disk.
b. Type one of the following paths under Copy manufacturer’s files
from:
For Windows 95,
type D:\setup\win95\english\drivers\oemsetup.inf
For Windows 98,
type D:\setup\win98\english\drivers\oemsetup.inf
c. Click OK.
You will see PM4410 highlighted.
7. Click Next.
8. Continue with the installation following the instructions on your
screen.
E-40
Pacemark 4410 Setup Guide
To Install the On-Line Registration Program
in Windows 95/98
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications and insert the Pacemark 4410 CD in
your CD-ROM drive.
2. Click Start Run.
3. Type D:/install and click OK.
4. Click the button beside On-Line Registration.
5. Follow the instructions on your screen.
To Run the On-Line Registration Program in Windows 95/98
1. Click the Start button on the Windows taskbar.
2. Choose Programs
PM4410.
3. Click OKI Pacemark 4410 On-Line Registration.
4. Follow the instructions on your screen.
Pacemark 4410 Setup Guide
E-41
To Install the On-Line Pacemark 4410 User’s Guide
in Windows 95/98
First, make sure Adobe Acrobat Reader is installed
To view the on-line Pacemark 4410 User’s Guide, you
must have Adobe Acrobat Reader version 3 or 4 installed
on your computer. If you do not already have Acrobat
Reader installed, it is provided on the Pacemark 4410 CD.
To install Acrobat Reader in Windows 95/98:
These instructions assume “D” is the location of your
CD-ROM drive.
1. Make sure all applications are closed and the Pacemark 4410 CD is
in your CD-ROM drive.
2. Click Start on the Windows task bar, then click Run.
3. For Windows 95,
type D:\acrobat\Windows\English\Win95\Ar32e30.exe
For Windows 98,
type D:\acrobat\Windows\English\Win98\ar405eng.exe
4. Click OK.
5. Follow the instructions on your screen.
Next, install the On-Line User’s Guide in Windows 95/98
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications and insert the Pacemark 4410 CD in
your CD-ROM drive.
2. Click Start Run.
3. Type D:/install and click OK.
4. Click the button beside On-Line Manual.
5. Follow the instructions on your screen.
Viewing the On-Line Pacemark User’s Guide in Windows 95/98
1. Click the Start
Programs
PM4410.
2. Click OKI Pacemark 4410 On-Line Manual.
E-42
Pacemark 4410 Setup Guide
To view the manual from the Pacemark 4410 CD, open
Acrobat Reader, click File Open, browse to the
Manuals\English directory on the CD, and double-click
e4410m.pdf .
Installation for Windows NT 4.0
Minimum System Requirements for Windows NT 4.0:
CPU: i486DX, 66 MHz (90 MHz pentium recommended)
RAM: 24 MB (32 MB recommended)
Empty hard disk space:
2 MB for use by print spooler
73 MB for User’s Guide (optional)
10 MB for Adobe Acrobat Reader Software (optional)
To Install the Pacemark 4410 Printer Driver
in Windows NT 4.0
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications and make sure that the printer is
connected to the PC and turned on.
2. Insert the Pacemark 4410 CD in your CD-ROM drive.
3. Click Start Run.
4. Type D:/install and click OK.
5. Click Printer Driver.
6. Follow the instructions on your screen. When you are prompted for
the printer:
a. Click Have Disk.
b. In the Copy manufacturer’s files from box, type
D:\Setup\Nt40\English\Drivers\printer.inf .
c. Click OK.
You will see PM4410 highlighted.
7. Click Next.
8. Continue with the installation following the instructions on your
screen.
Pacemark 4410 Setup Guide
E-43
To Install the On-Line Registration Program
in Windows NT 4.0
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications and insert the Pacemark 4410 CD in
your CD-ROM drive.
2. Click Start Run.
3. Type D:/install and click OK.
4. Click the button beside On-Line Registration.
5. Follow the instructions on your screen.
To Run the Electronic Registration Program
in Windows NT 4.0
1. Click Start Programs
PM4410.
2. Click OKI Pacemark 4410 On-Line Registration.
3. Follow the instructions on your screen.
E-44
Pacemark 4410 Setup Guide
To Install the On-Line Pacemark 4410 User’s Guide
in Windows NT 4.0
First, make sure Adobe Acrobat Reader is installed
To view the on-line Pacemark 4410 User’s Guide, you
must have Adobe Acrobat Reader version 3 or 4 installed
on your computer. If you don’t already have Acrobat
Reader installed, Acrobat Reader 4.05 is provided on the
Pacemark 4410 CD.
To install Acrobat Reader in Windows NT 4.0:
These instructions assume “D” is the location of your
CD-ROM drive.
1. Make sure all applications are closed and the Pacemark 4410 CD is
in your CD-ROM drive.
2. Click Start Run.
3. Type D:\Acrobat\Windows\English\Nt40\ar405eng.exe.
4. Click OK.
5. Follow the instructions on your screen.
Next, Install the On-Line User’s Guide in Windows NT 4.0
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications and insert the Pacemark 4410 CD in
your CD-ROM drive.
2. Click the Start Run.
3. Type D:/install and click OK.
4. Click the button beside On-Line Manual.
5. Follow the instructions on your screen.
Viewing the On-Line Pacemark User’s Guide in Windows NT 4.0
1. Click Start Programs
PM4410.
2. From the submenu, click OKI Pacemark 4410 On-Line Manual.
To view the manual from the Pacemark 4410 CD, open
Acrobat Reader, click File Open, browse to the
Manuals\English directory on the CD, and double-click
e4410m.pdf .
Pacemark 4410 Setup Guide
E-45
Installation for Windows 3.1x
Minimum System Requirements for Windows 3.1x:
CPU: i486DX, 66 MHz (90 MHz pentium recommended)
RAM: 8 MB (16 MB recommended)
Empty hard disk space:
2 MB for use by print spooler
73 MB for User’s Guide (optional)
5 MB for Adobe Acrobat Reader Software (optional)—
12 MB recommended
To Install the Pacemark 4410 Printer Driver and
On-Line Registration Program in Windows 3.1x
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications and make sure that the printer is
connected to the PC and turned on.
2. Insert the Pacemark 4410 CD in your CD-ROM drive.
3. Click File Run.
4. Type D:\install, then click OK.
5. Click On-Line Registration/Printer Driver.
6. Follow the instructions on your screen.
To Run the On-Line Registration Program in Windows 3.1x
To run the On-Line Registration program:
1. Double click the PM4410 group from the Program Manager.
2. Double click the OKI Pacemark 4410 On-Line Registration icon.
3. Follow the instructions on your screen.
E-46
Pacemark 4410 Setup Guide
To Install the On-Line Pacemark 4410 User’s Guide
in Windows 3.1x
First, make sure Adobe Acrobat Reader is installed
To view the on-line Pacemark 4410 User’s Guide, you
must have Adobe Acrobat Reader version 3.01 installed on
your computer. Acrobat Reader 3.01 is provided on the
Pacemark 4410 CD. If you already have Acrobat Reader
installed, you do not need to reinstall it.
To Install Acrobat Reader in Windows 3.1x:
These instructions assume “D” is the location of your
CD-ROM drive.
1. Make sure all applications are closed and the Pacemark 4410 CD is
in your CD-ROM drive.
2. Click File Run.
3. Type D:\Acrobat\Windows\English\Win31\ar16e30.exe.
4. Click OK.
5. Follow the instructions on your screen.
Next, install the Pacemark 4410 User’s Guide in Windows 3.1x
These instructions assume “D” is the location of your
CD-ROM drive.
1. Close any open applications.
2. Insert the Pacemark 4410 CD in your CD-ROM drive.
3. Click File Run.
4. Type D:\install, then click OK.
5. Click the button beside On-Line Manual.
6. Follow the on-screen instructions.
Viewing the On-Line Pacemark User’s Guide in Windows 3.1x
1. Double click the PM4410 group from the Program Manager.
2. Double click the OKI Pacemark 4410 On-Line Manual icon.
To view the manual from the Pacemark 4410 CD, open
Acrobat Reader, click File Open, browse to the
Manuals\English directory on the CD, and double-click
e4410m.pdf .
Pacemark 4410 Setup Guide
E-47
E-48
Pacemark 4410 Setup Guide
Front Panel
Overview
Print Mode
Power Light: indicates that printer is turned on.
MENU Button:
Press to enter Menu mode.
Alarm Light:
On: indicates printer
error, such as paper out.
Blinking: Indicates
printer error such as
ROM/RAM error, spacing
error, etc.
GROUP/ITEM/OPTION Buttons:
For use in Menu Mode only
Status Light:
On: indicates that printer is
ready to receive data.
Blinking: Printer is in Print
STORE Button:
Suppress mode.
For use in Menu
Mode only
ON-LINE/RESET Button:
Press to switch printer on/off line.
With SHIFT, press and hold to reset printer.
Pacemark 4410 Setup Guide
E-49
PATH/TOF Button:
With printer off line:
Press to switch paper paths
Hold to set current paper position as Top of Form
CONFIG Button:
LF/Micro Feed Down Button:
With printer off line and no
data being sent:
Press to execute line feed
With SHIFT, press for reverse fine line feeds
(1/144” increments)
Press to switch between
preset menu configurations
CFG1 and CFG2.
For more information on the
preset menu configurations,
see Section 1 of the OKI
Pacemark 4410 On-Line User’s
Guide.
PARK Button:
Press to park form currently in
paper path.
SHIFT Button:
Press and hold to engage alternate
(lower) button functions.
TEAR Button:
Press to move form up to tear
position.
FF/LOAD/Micro Feed Up Button:
Press to move paper to next Top of Form
If paper is parked, press to feed paper into print position
With SHIFT, press for fine line feeds (1/144”increments)
E-50
Pacemark 4410 Setup Guide
Menu Mode
MENU Button:
Press to exit Menu mode.
With SHIFT, press to print out a listing of the
current menu settings.
ON-LINE/RESET Button:
Press to exit Menu mode.
STORE Button:
Press to save the new
setting.
GROUP Button:
OPTION Button:
Press to page through available
groups in the menu.
Press to page through available
setting values for the selected
item.
With SHIFT, press to page backwards
through available groups.
With SHIFT, press to page
backwards through available
setting values.
ITEM Button:
Press to page through available items for
the selected group.
With SHIFT, press to page backwards
through available items.
Pacemark 4410 Setup Guide
E-51
Top of Form (TOF)
The red line (1) on the paper shield indicates where the Top of Form
(TOF) is located.
1
The TOF must be set separately for each paper path.
The factory setting for TOF is 0.35 inch (9 mm) down from
the top of the page.
Setting the TOF
The TOF can be set with the printhead access cover open. The
printer can be either on or off-line.
To set the TOF in fine increments over a limited area:
3
1
2
E-52
Pacemark 4410 Setup Guide
If you have the Forms Tear-Off feature turned on in the menu,
before performing the steps below, press and hold TEAR to
move the paper into the print position, Then, while holding
SHIFT, press TEAR to release the tear, and follow the
instructions below.
1. To move the TOF up:
a. Press and hold SHIFT (1) while pressing LF/Micro Feed Down
(2).
b. Press and hold SHIFT, then press PATH/TOF to save the setting.
2. To move the TOF down:
a. Press and hold SHIFT (1) while pressing FF/LOAD/Micro Feed
Up (3).
b. Press and hold SHIFT, then press PATH/TOF to save the setting.
Resetting Top of Form to the Factory Setting
To reset the TOF to the factory setting, turn the printer off, then press
and hold GROUP and OPTION (1) while turning the printer back on.
1
Pacemark 4410 Setup Guide
E-53
Temporarily Changing the Print Start Position
To set the print start position lower for one page only: press LF (1) until
you reach the position on the paper where you want the printing to start.
1
E-54
Pacemark 4410 Setup Guide
Printer
Features
Preset Menu Configurations
Once you have made changes in Menu settings, you can save them in
one of two preset storage areas — CFG1 and CFG2 — and use them
instead of the factory settings.
To switch back and forth between stored settings:
1. Press ON-LINE/RESET.
The printer goes off line.
2. Press CONFIG.
The CFG designation on the display changes.
3. Press ON-LINE/RESET.
The printer goes back on line with the new CFG showing on the
display.
For information on how to store Menu settings as CFG1 or CFG2, see
Section 1 of your on-line Pacemark 4410 User’s Guide.
Tear Feature
1
Use this feature to advance continuous forms up to the tear position by
pressing TEAR (1).
Pacemark 4410 Setup Guide
E-55
Forms Tear-Off Feature
Caution! Never engage Forms Tear-Off when printing on
labels.
Forms Tear-Off automatically moves continuous forms up to the tear
position after the interval you select, then moves it back down again for
printing when the printer receives more data.
This feature is normally turned off. To activate it:
1. Press MENU to enter the menu mode.
2. Press GROUP until the paper path you are using appears on the
second line of the display.
3. Press ITEM until Form Tear-Off appears on the display.
4. Press OPTION until the time interval setting you wish to select
appears.
5. Press STORE to save that setting.
6. Press MENU to exit the menu mode.
Some programs pause occasionally while sending data. If the
pause is too long, the paper will advance to the tear-off
position until more data is received. This extra paper
movement can cause uneven print registration in graphics. If
you have this problem, use the menu to turn off the Forms
Tear-Off feature.
E-56
Pacemark 4410 Setup Guide
Adjusting the Tear-Off Position
The tear-off positions for the front and rear paper paths are set
independently.
To adjust the tear-off position for the paper currently in the paper path:
2
1
3
• Hold SHIFT (1) and press FF/LOAD/Micro Feed Up (2) repeatedly
to move the continuous forms up
• Hold SHIFT (1) and press LF/Micro Feed Down (3) repeatedly to
move the continuous forms down.
Paper Park Feature
1
When you press PARK (1), the continuous forms currently in the print
path retract out of the path and are placed in the parked position
(remaining loaded on the tractors, ready to feed in again) and the
ALARM light comes on.
To reload the forms, press FF/LOAD.
To load the forms from the alternate paper path, press PATH/TOF.
Pacemark 4410 Setup Guide
E-57
E-58
Pacemark 4410 Setup Guide
Specifications
For additional specifications, see Appendix A in the on-line
Pacemark 4410 User’s Guide.
Electrical Specifications
Voltage:
90 to 264 Volts, AC, universal
Frequency: 50 or 60 Hz, +/- 2%
Power Consumption
Idling: Less than 15 watts
Local Test: About 295 watts
Environmental Specifications
Temperature
Operating: 41 to 95°F (5 to 35°C)
Storage: 14 to 109°F (-10 to +43°C)
Relative Humidity
Operating: 20 to 80% RH,
maximum wet bulb temperature 86°F (30°C)
Storage: 5 to 95% RH,
maximum wet bulb temperature 104°F (40°C)
Pacemark 4410 Setup Guide
E-59
E-60
Pacemark 4410 Setup Guide
Limited
Warranty
Oki Data Americas, Inc. (Oki Data) warrants this printer to be free from
defect in material and workmanship and will remedy any such defect
according to the terms of this Limited Warranty. This Limited Warranty
extends to the original purchaser only. This Limited Warranty does not
extend to network setup, application conflicts, or consumable items,
including but not limited to ribbons, fuses, etc.
Oki Data will repair (or at its option, replace) at no charge, any
defective component(s) of the printer for two (2) years from the date of
purchase except for the printhead, which is warranted for a period of
one (1) year from date of purchase. This Limited Warranty extends to
the original purchaser only.
On-Site Repair
On-Site repair is available in the United States and Canada
only.
On-Site repair is available without charge, in the United States and
Canada, provided that the warranty service is performed by an
Authorized Oki Data Service Center, located within a fifty (50) mile
radius of the original purchaser's facility. Purchasers outside the fifty
(50) mile radius may return the product, shipping prepaid, to an Oki
Data Authorized Service Center. A listing of Oki Data Authorized
Service Centers may be obtained by calling 1-800-OKI-DATA
(1-800-654-3282).
To make request or claim for service under this Limited Warranty,
contact your Oki Data Authorized Dealer, authorized third-party service
provider, or Oki Data.
Pacemark 4410 Setup Guide
E-61
A written receipt for the product, showing the date of purchase, dealer’s
name, and serial number of the Pacemark 4410 printer, must
accompany any request or claim for work to be performed under this
Limited Warranty.
This Limited Warranty shall not apply if the product has been damaged
due to abuse, misuse, misapplication, accident, or as a result of service
or modification by any other than an authorized Oki Data service center.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE
ON THE FACE HEREOF AND DESCRIBED ABOVE. NO
WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, SHALL EXTEND BEYOND THE RESPECTIVE
WARRANTY PERIOD DESCRIBED ABOVE. Some states do not
allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you.
OKI DATA SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LOSS ARISING FROM THE USE OF THIS PRODUCT. Some states
do not allow the exclusion or limitation of incidental or consequential
damages, so the above exclusion may not apply to you.
Additional information on obtaining service under this Limited
Warranty is available by contacting the Oki Data dealer from whom the
product was purchased, by contacting Oki Data directly at
1-800-OKI-DATA (U.S. and Canada, English only) or at
1-609-222-5276 (Spanish only), or by contacting one of the service
locations listed below.
E-62
Pacemark 4410 Setup Guide
United States
Canada
Oki Data Americas, Ltd.
Oki Data Americas, Ltd.
Tel: 1-800-OKI-DATA (1-800-654-3282) Tel: 1-800-OKI-DATA (1-800-654-3282)
Fax: 1-609-222-5247
Fax: 905-238-4427
Brazil
Mexico
Oki Data do Brasil, Ltda.
Oki Data de Mexico, S.A. de C.V.
Tel: (5511) 5589-1518
Fax: (5511) 5584-0267
Tel: 525-263-8780
Fax: 525-250-3501
This Limited Warranty applies to this printer. However, the procedure
for obtaining service may vary outside the continental United States.
Contact your Oki Data dealer for such warranty service information.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Pacemark 4410 Setup Guide
E-63
E-64
Pacemark 4410 Setup Guide
FCC/IC/CE
Statements
Declaration of Conformity
We declare here that this device has been tested and found to comply
with the FCC Standards, Part 15 Class B.
Model Name: Dot Matrix Printer PM4410
Model Number: D21001A
This device complies with Part 15 of FCC Rules. Operation is subject to
the following two conditions: This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may be cause undesired operation.
Oki Data Corporation
Takasaki Campus
8-1, Futaba-cho, Takasaki-shi, Gunma-ken, Japan
(Signed)
Isao Suda
Dated: October 5, 1998
for
Oki Data Americas, Inc.
2000 Bishops Gate Blvd. Mt. Laurel, NJ 08054-4620
Pacemark 4410 Setup Guide
E-65
Federal Communications Commission (FCC)
Radio Frequency Interference (RFI) Statement
WARNING: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Plug the unit into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/television technician for
help.
It is the responsibility of the user to obtain the required
shielded cable in order to ensure compliance of this equipment
with FCC regulations.
Changes or modifications not expressly approved by Oki Data may void
your authority to operate this device.
Industry Canada (IC)
Radio Interference (RI) Statement
This OKI apparatus complies with the Class B limits for radio
interference as specified in the Industry Canada Radio Interference
Regulations.
European Union Council of the European
Communities Statement of Electromagnetic
Conformance
This product complies with the requirements of the Council Directive
89/336/EEC on the approximation of the laws of the member states
relating to electromagnetic compatibility.
E-66
Pacemark 4410 Setup Guide
Material Safety
Data Sheet
Oil
MSDS No. 58077401
CAS# Not applicable
OSHA TWA Not applicable
ACGIH TLV Not applicable
for Pacemark 4410
Black Ribbon, P/N 40629302
For more information, contact
Oki Data at:
Additives
CAS# Not applicable
OSHA TWA Not applicable
ACGIH TLV Not applicable
2000 Bishops Gate Blvd.
Mount Laurel, NJ 08054-4620
For Emergency Information, call
1-800-OKI-DATA (1-800-654-
3282 — US and Canada only).
Nylon 6-6 Fabric
CAS# Not applicable
OSHA TWA Not applicable
ACGIH TLV Not applicable
Emergency First Aid
Procedures
Physical Data
Emergency Procedure
Melting Point: No data available
Boiling Point: No data available
Vapor Pressure: No data
available
Vapor Density (Air = 1): No
Contact
occurs
Flush eyes with large
quantities of water for
15 minutes, keeping
eyelids open with
fingers. Seek medical
attention.
with eyes.
data available
Evaporation Rate (Butyl
Acetate = 1): No data available
Specific Gravity (H2O=1): No
data available
Contact
occurs
with skin.
Wash thoroughly with
soap and water.
Solubility in Water: No data
available
Appearance and Odor: Nylon
6-6 fabric impregnated with
liquid black ink
Hazardous Ingredients
None
Coloring Material
CAS# Not applicable
OSHA TWA Not applicable
ACGIH TLV Not applicable
Current as of 2/1/00
Pacemark 4410 Setup Guide
E-67
Fire and Explosion
Hazard Data
Safe Handling and Use
Respiratory Protection: None
Protective Gloves and/or Eye
Protection: Not normally
required. Protective gloves
desirable in some cases.
Flash Point (Method Used):
N/A
Flammable Limits, LEL/UEL:
N/A
Ventilation: Not applicable
Extinguishing Media: Water
mist, Foam, Dry powder,
CO2 gas
Other Protective Equipment
and/or Hygienic Practices:
N/A
Special Fire and Explosion
Procedures: None
Unusual Fire and Explosion
Special Precautions
Precautions for Handling or
Storage: Store in a dark, cold
place. Do not pull ribbon out of
cassette except for mounting on
printer.
Hazards: None
Health Hazard Data
Routes of Entry: Ingestion,
Eyes, Skin
Health Hazards: None
Other Precautions: N/A
Reactivity Data
Stability: Stable
Polymerization: Will not occur.
Hazardous Decomposition or
By products: None
Conditions to Avoid: None
Incompatibility (Materials to
The information contained in
this MSDS is based on data
considered accurate; however,
no warranty is expressed or
implied regarding the accuracy
of these data or the results to be
obtained from the use thereof.
Vendor assumes no
responsibility for injury to
vendee or third person party
proximately caused by the
product if reasonable safety
procedures are not adhered to as
stipulated in the MSDS.
Furthermore, vendor assumes no
responsibility for injury to
vendee or third person party
proximately caused by abnormal
use of the product even if
reasonable safety procedures are
followed. Additionally, vendee
assumes the risk of his use of
the product.
Avoid): None
Spill Cleanup and
Disposal
Spill Cleanup: If the ribbon is
inadvertently pulled out, it
should be rewound on the reel
using the take-up knob.
Waste Disposal: Follow
appropriate federal, state and
local regulations.
E-68
Pacemark 4410 Setup Guide
Pacemark 4410
Printed User’s Guide Request Form
Pacemark Model (check one): ❏ 4410 ❏ 4410 Network Version
Serial No.: __ __ __ __ __ __ __ __ __ __ __
(look for silver label on side or back of printer)
Check one:
English ❏ MS-10233/1299 Pacemark 4410 User’s Guide
Français ❏ MS-10234/1299 Pacemark 4410 Guide de L’utilisateur
Español ❏ MS-10235/1299 Pacemark 4410 Guía del usuario
Português ❏ MS-10236/1299 Pacemark 4410 Guia do usuário
Name: __________________________________________________
Company: ____________________________________________
Address: ______________________________________________
City: __________________________ State: ____ ZIP: _________
Country: _________________________
Option 1
MAIL this form to:
Oki Data
PO Box 4603
Trenton, NJ 08650-9852
Option 2
FAX this form to (609) 393-0338.
Option 3
CALL: In the US and Canada (English only), call 1-800-545-4747
and tell the operator you wish to order an Oki Data manual. You will
be transferred to an order taker: be prepared to provide the
information from the form above.
|