NEC MULTISYNC P553 User Manual

User’s Manual  
MultiSync P403  
MultiSync P463  
MultiSync P553  
DECLARATION OF CONFORMITY  
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
U.S. Responsible Party: NEC Display Solutions of America, Inc.  
Address:  
500 Park Boulevard, Suite 1100  
Itasca, Illinois 60143  
(630) 467-3000  
Tel. No.:  
Type of Product:  
Display Monitor  
Equipment Classification: Class B Peripheral  
Model:  
MultiSync P403 (P403)  
MultiSync P463 (P463)  
MultiSync P553 (P553)  
We hereby declare that the equipment speciÞed above  
conforms to the technical standards as speciÞed in the FCC Rules.  
FCC Information  
1. Use the attached specified cables with the MultiSync P403 (P403)/MultiSync P463 (P463)/MultiSync P553 (P553) colour  
monitor so as not to interfere with radio and television reception.  
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.  
(2) Please use the supplied shielded video signal cable, DVI-D to DVI-D cable.  
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult your dealer or an experienced radio/TV technician for help.  
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.  
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify  
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington,  
D.C., 20402, Stock No. 004-000-00345-4.  
Windows is a registered trademark of Microsoft Corporation.  
NEC is a registered trademark of NEC Corporation.  
OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and  
Switzerland.  
DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards  
Association.  
All other brands and product names are trademarks or registered trademarks of their respective owners.  
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC  
in the United States and other countries.  
Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and  
areas.  
CRESTRON and ROOMVIEW are registered trademarks of Crestron Electronics, Inc. in the United States and other countries.  
GPL/LGPL Software Licenses  
The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL),  
and others.  
For more information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied CD-ROM.  
English-1  
Important Information  
WARNING  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT  
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE  
PRONGS CAN BE FULLY INSERTED.  
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
CAUTION  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM  
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER  
CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric  
shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.  
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has  
been included. Therefore, it should be read carefully in order to avoid any problems.  
CAUTION: Please use the power cord provided with this monitor in accordance with the table below. If a power cord is not  
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the  
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.  
European  
Continental  
Plug Type  
North America  
U.K.  
Chinese  
Japanese  
Plug Shape  
U.S.A./Canada  
120*  
Region  
Voltage  
EU (except U.K.)  
230  
U.K.  
230  
China  
220  
Japan  
100  
* When operating the MultiSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power  
supply voltage of the AC power outlet being used.  
NOTE:  
This product can only be serviced in the country where it was purchased.  
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.  
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.  
English-2  
Safety Precautions, Maintenance & Recommended Use  
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE  
FOLLOWING WHEN SETTING UP AND USING  
THE MULTI-FUNCTION MONITOR:  
Immediately unplug your monitor from the wall outlet and refer  
servicing to qualified service personnel under the following  
conditions:  
DO NOT OPEN THE MONITOR. There are no user  
serviceable parts inside and opening or removing covers may  
expose you to dangerous shock hazards or other risks. Refer  
all servicing to qualified service personnel.  
When the power supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen into the monitor.  
If the monitor has been exposed to rain or water.  
If the monitor has been dropped or the cabinet damaged.  
Do not spill any liquids into the cabinet or use your monitor  
near water.  
If you notice any structural damage such as cracks or  
unnatural wobbling.  
Do not insert objects of any kind into the cabinet slots,  
as they may touch dangerous voltage points, which can  
be harmful or fatal or may cause electric shock, fire or  
equipment failure.  
If the monitor does not operate normally by following  
operating instructions.  
Recommended Use  
Do not place any heavy objects on the power cord.  
Damage to the cord may cause shock or fire.  
For optimum performance, allow 20 minutes for warm-up.  
Rest your eyes periodically by focusing on an object at least  
5 feet away. Blink often.  
Do not place this product on a sloping or unstable cart, stand  
or table, as the monitor may fall, causing serious damage to  
the monitor.  
Position the monitor at a 90° angle to windows and other light  
sources to minimize glare and reflections.  
Do not mount this product upside down for an extended period  
of time as it may cause permanent damage to the screen.  
Clean the LCD monitor surface with a lint-free, non-abrasive  
cloth. Avoid using any cleaning solution or glass cleaner!  
The power supply cord you use must have been approved by  
and comply with the safety standards of your country. (Type  
H05VV-F 3G 1mm2 should be used in Europe)  
Adjust the monitor’s brightness, contrast and sharpness  
controls to enhance readability.  
In UK, use a BS-approved power cord with molded plug  
having a black (13A) fuse installed for use with this monitor.  
Avoid displaying fixed patterns on the monitor for long  
periods of time to avoid image persistence (after image  
effects).  
Do not place any objects onto the monitor and do not use the  
monitor outdoors.  
Get regular eye checkups.  
Do not bend, crimp or otherwise damage the power cord.  
If glass is broken, handle with care.  
Ergonomics  
To realize the maximum ergonomic benefits, we recommend the  
following:  
Do not cover vent on monitor.  
Do not use monitor in high temperature, humid, dusty, or oily  
areas.  
Use the preset Size and Position controls with standard  
signals.  
If monitor or glass is broken, do not come in contact with the  
liquid crystal and handle with care.  
Use the preset Color Setting.  
Use non-interlaced signals.  
Allow adequate ventilation around the monitor, so that heat  
can properly dissipate. Do not block ventilated openings or  
place the monitor near a radiator or other heat sources.  
Do not put anything on top of the monitor.  
Do not use primary color blue on a dark background, as  
it is difficult to see and may produce eye fatigue due to  
insufficient contrast.  
The power cable connector is the primary means of detaching  
the system from the power supply. The monitor should be  
installed close to a power outlet, which is easily accessible.  
Cleaning the LCD Panel  
When the liquid crystal panel is dusty, please gently wipe  
with a soft cloth.  
Do not move or mount this product by hanging a rope or wire  
to the backside handle.  
Do not mount or secure this product by using the backside  
handle. It may fall and cause personal injury.  
Please do not rub the LCD panel with hard material.  
Please do not apply pressure to the LCD surface.  
Please do not use OA cleaner as it will cause deterioration or  
discolor on the LCD surface.  
Handle with care when transporting. Save packaging for  
transporting.  
Cleaning the Cabinet  
If using the cooling fan continuously, it is recommended to  
wipe holes clean a minimum of once a month.  
Unplug the power supply  
Please clean the holes of back cabinet to reject dirt and dust  
at least once a year because of set reliability.  
Gently wipe the cabinet with a soft cloth  
To clean the cabinet, dampen the cloth with a neutral  
detergent and water, wipe the cabinet and follow with a dry  
cloth.  
When using a LAN cable, do not connect to a peripheral  
device with wiring that might have excessive voltage.  
Do not use monitor under rapid temperature and humidity  
change condition or avoid cold air from air-conditioning outlet  
directly, as it may shorten the lifetime of the monitor or cause  
condensation. If condensation happens, let the monitor stand  
unplugged until there is no condensation.  
NOTE: DO NOT clean with benzene thinner, alkaline detergent,  
alcoholic system detergent, glass cleaner, wax, polish  
cleaner, soap powder, or insecticide. Rubber or vinyl  
should not be in contact with the cabinet for an extended  
period of time. These types of fluids and materials can  
cause the paint to deteriorate, crack or peel.  
Connecting to a TV*  
Cable distribution system should be grounded (earthed) in  
accordance with ANSI/NFPA 70, the National Electrical Code  
(NEC), in particular Section 820.93, Grounding of Outer  
Conductive Shield of a Coaxial Cable.  
The screen of the coaxial cable is intended to be connected  
to earth in the building installation.  
* The product you purchased may not have this feature.  
English-3  
Contents  
Your new MultiSync monitor box* should contain the following:  
LCD monitor  
Power cord*1  
Clamp x 1 (P403/P463)/x 3 (P553)  
Screw with washer (M4 x 10) x 1 (P403/P463)/x 3 (P553)  
Thumbscrew for optional stand x 2*2  
CD-ROM  
Video Signal Cable  
Wireless Remote Control and AAA Batteries  
Setup Manual  
Video Signal Cable  
(DVI-D to DVI-D cable)  
Power Cord*1  
Screw with washer  
(M4 x 10) x 1 (P403/P463)/  
x 3 (P553)  
Clamp x 1 (P403/P463)/  
x 3 (P553)  
Thumbscrew for  
optional stand x 2*2  
Setup Manual  
CD-ROM  
Setup Manual  
Wireless Remote Control  
and AAA Batteries  
*
*
Remember to save your original box and packing material to transport or ship the monitor.  
1
2
Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one  
power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by  
and complies with the safety standard of your particular country.  
*
P553 only.  
English-4  
Installation  
This device cannot be used or installed without the Tabletop  
Stand or other mounting accessory for support. For proper  
installation it is strongly recommended to use a trained,  
NEC authorized service person. Failure to follow NEC  
standard mounting procedures could result in damage to the  
equipment or injury to the user or installer. Product warranty  
does not cover damage caused by improper installation.  
Failure to follow these recommendations could result in  
voiding the warranty.  
Orientation  
When using the display in the portrait position, the  
monitor should be rotated clockwise so that the left side  
is moved to the top and the LED indicator light is on  
the bottom. This will allow for proper ventilation and will  
extend the lifetime of the monitor. Improper ventilation  
may shorten the lifetime of the monitor.  
Mounting  
DO NOT mount the monitor yourself. Please ask dealer.  
For proper installation it is strongly recommended to use  
a trained, qualified technician. Please inspect the location  
where the unit is to be mounted. Mounting on wall or ceiling  
is the customer’s responsibility. Not all walls or ceilings are  
capable of supporting the weight of the unit. Product warranty  
does not cover damage caused by improper installation,  
remodelling, or natural disasters. Failure to comply with these  
recommendations could result in voiding the warranty.  
DO NOT block ventilated openings with mounting  
accessories or other accessories.  
For NEC Qualified Personnel:  
LED Indicator  
To ensure safe installation, use two or more brackets to  
mount the unit. Mount the unit to at least two points on the  
installation location.  
Mounting location  
The ceiling and wall must be strong enough to support the  
monitor and mounting accessories.  
Please note the following when mounting  
on wall or ceiling  
DO NOT install in locations where a door or gate can hit  
the unit.  
When using mounting accessories other than those that  
are NEC approved, they must comply with the VESA-  
compatible (FDMlv1) mounting method.  
DO NOT install in areas where the unit will be subjected  
to strong vibrations and dust.  
DO NOT install near where the main power supply enters  
the building.  
Mounting  
Bracket  
Unit  
No gap  
NEC strongly recommends  
using size M6 screws  
(10-12 mm + thickness  
of bracket and washers in  
length). If using screws  
longer than 10-12 mm,  
check the depth of the hole.  
(Recommended Fasten  
Force: 470 - 635N•cm)  
NEC recommends mounting  
interfaces that comply with  
UL1678 standard in North  
America.  
No thread  
4 mm  
Washers  
Do not install in where people can easily grab and hang  
onto the unit or the mounting apparatus.  
under  
8.5 mm  
Screw  
When mounting in a recessed area, as in a wall, leave at  
least 4 inches (100 mm) of space between the monitor  
and the wall for proper ventilation.  
10-12 mm  
Thickness  
of bracket  
and washers  
Allow adequate ventilation or provide air conditioning  
around the monitor, so that heat can properly dissipate  
away from the unit and mounting apparatus.  
Screw length should equal  
depth of hole (10-12 mm) + the  
thickness of mounting bracket  
and washers. Bracket hole  
should be under 8.5 mm.  
Mounting on ceiling  
Ensure that the ceiling is sturdy enough to support the  
weight of the unit and the mounting apparatus over time,  
against earthquakes, unexpected vibrations, and other  
external forces.  
Prior to mounting, inspect the installation location to  
insure that it is strong enough to support the weight of the  
unit so that the unit will be safe from harm.  
Refer to the instructions included with the mounting  
equipment for detailed information.  
Be sure the unit is mounted to a solid structure within  
the ceiling, such as a support beam. Secure the monitor  
using bolts, spring lock washers, washer and nut.  
Make sure there is no gap between the monitor and the  
bracket.  
DO NOT mount to areas that have no supporting internal  
structure. DO NOT use wood screws or anchor screws for  
mounting. DO NOT mount the unit to trim or to hanging  
fixtures.  
Maintenance  
Periodically check for loose screws, gaps, distortions,  
or other problems that may occur with the mounting  
apparatus. If a problem is detected, please refer to  
qualified personnel for service.  
Regularly check the mounting location for signs of  
damage or weakness that may occur over time.  
English-5  
3. Installing and removing optional table  
top stand  
Attaching Mounting Accessories  
The monitor is designed for use with the VESA mounting  
system.  
CAUTION: Installing and removing the stand must be done  
by two or more people.  
1. Attach Mounting Accessories  
To install, follow those instructions included with the stand or  
mounting apparatus. Use only those devices recommended  
by the manufacturer.  
Be careful to avoid tipping monitor when attaching  
accessories.  
VESA Mounting Interface  
NOTE:  
For P403/P463, use ONLY thumbscrews which  
are included with the optional table top stand.  
For P553, use ONLY thumbscrews which are  
included in the monitor.  
When installing the LCD monitor stand, handle the unit with  
care to avoid pinching your fingers.  
Optional table top stand  
300 mm  
Mounting accessories can be attached with the monitor in  
the face down position. To avoid damaging the screen face,  
place the protective sheet on the table underneath the LCD.  
The protective sheet was wrapped around the LCD in the  
original packaging. Make sure there is nothing on the table  
that can damage the monitor.  
Table  
Protective Sheet  
NOTE:  
Install the stand so the long end of the feet face  
forward. Use the ST-322 for the P403/P463 and  
the ST-5220 for the P553.  
When using mounting accessories other than NEC compliant  
and approved, they must comply with the VESA-compatible  
mounting method.  
4. Ventilation Requirements  
When mounting in an enclosed space or recessed area,  
leave adequate room between the monitor and the enclosure  
to allow heat to disperse, as shown below.  
2. Using Option Board  
1. Turn off the main power switch.  
2. Remove the handle.*1  
3. Remove the attached slot cover by unscrewing the  
installed screws (Figure 1).  
4. Insert option board in to the monitor. Attach the slot cover  
by using the removed screws.  
5. Attach the handle.*1  
NOTE:  
Please contact your supplier for available option  
boards.  
Do not apply excessive force to manipulate the  
optional board before fixing it with screws.  
Allow adequate ventilation or provide air conditioning around  
the monitor, so that heat can properly dissipate away from  
the unit and mounting apparatus; especially when you use  
monitors in multiple screen.  
NOTE:  
The sound quality of the internal speakers will  
differ according to the acoustics of the room.  
(P403/P463 only)  
Figure 1  
*1: P403/P463 only.  
English-6  
5. Prevent Tipping  
When using the display with the optional table top stand  
fasten the LCD to a wall using a cord or chain that can  
support the weight of the monitor in order to prevent the  
monitor from falling. Fasten the cord or chain to the monitor  
using the provided clamps and screws.  
For the P403/P463, the clamps and screws are included with  
the optional table top stand.  
100 mm  
Screw Holes  
Cord or chain  
Clamp  
Screw (M4)  
Before attaching the LCD monitor to the wall, make sure that  
the wall can support the weight of the monitor.  
Be sure to remove the cord or chain from the wall before  
moving the LCD.  
English-7  
Parts Name and Functions  
Control Panel  
³ POWER button (  
)
º EXIT button (EXIT)  
Switches the power on/off. See also page 16.  
Activates the OSD menu when the OSD menu is turned-off.  
Acts as EXIT button within the OSD to move to previous  
menu.  
· MUTE button (MUTE)  
Switches the audio mute ON/OFF.  
¾ Remote control sensor and Power Indicator  
» INPUT button (INPUT)  
Receives the signal from the remote control (when using the  
wireless remote control). See also page 11.  
Acts as SET/POINT ZOOM button within OSD menu.  
(Toggle switches between [DVI], [DPORT], [HDMI], [VGA] or  
[Y/Pb/Pr], [SCART]*, [VIDEO]*, [S-VIDEO]*, [DPORT2]*,  
[DPORT3]*, [HDMI2]*, [RGB/HV]* or [Y/Pb/Pr2]*). These are  
available input only, shown as their factory preset name.  
Glows green when the LCD monitor is in active mode*.  
Glows red when the LCD is in POWER OFF mode.  
Glows amber when the monitor is in Power Save Mode.  
Green and Amber blink alternately while in Power Standby  
mode with the “SCHEDULE SETTINGS” function enabled.  
When a component failure is detected within the monitor, the  
indicator will blink red.  
¿ PLUS button (+)  
Acts as (+) button to increase the adjustment with OSD menu.  
Increases the audio output level when the OSD menu is  
turned off.  
* If “OFF” is selected in “POWER INDICATOR” (see page 24),  
LED will not light when the LCD monitor is in active mode.  
µ Room light sensing sensor  
´ MINUS button (-)  
Acts as (-) button to decrease the adjustment with OSD menu.  
Decreases the audio output level when the OSD menu is  
turned off.  
Detects the level of ambient light, allowing the monitor  
to make automatic adjustments to the backlight setting,  
resulting in a more comfortable viewing experience. Do not  
cover this sensor. See page 28.  
² UP button (  
Activates the OSD menu when the OSD menu is turned-off.  
Acts as button to move the highlighted area up to select  
adjustment items within OSD menu.  
)
¸ Intelligent wireless data sensor  
Sensor for wireless communication of the monitor information  
and settings.  
Control Key Lock Mode  
DOWN button (  
Activates the OSD menu when the OSD menu is turned-off.  
Acts as button to move the highlighted area down to select  
adjustment items within OSD menu.  
)
This control completely locks out access to all Control Key  
functions. To activate the control key lock function, press  
both and and hold down simultaneously for more than  
3 seconds. To resume user mode, press both and and  
hold simultaneously for more than 3 seconds.  
*: This function depends on which option board you use.  
English-8  
Terminal Panel  
³ AC IN connector  
µ REMOTE IN  
Connects with the supplied power cord.  
Use the optional wired remote control by connecting it to your  
monitor.  
· Main Power Switch  
NOTE: Do not use this connector unless specified.  
On/Off switch to turn main power ON/OFF.  
¸VGA IN (mini D-Sub 15 pin)  
» EXTERNAL SPEAKER TERMINAL  
To input analog RGB signals from a personal computer or  
from other RGB equipment. This input can be used with an  
RGB or COMPONENT source. Please select signal type in  
TERMINAL SETTING. See page 26.  
NOTE: When you use this connector for COMPONENT,  
please use a suitable signal cable. If you have any questions,  
please ask your dealer.  
To output the audio signal from AUDIO 1, DPORT and HDMI.  
Red terminal is plus (+).  
Black terminal is minus (-).  
NOTE: This speaker terminal is for 15 W + 15 W (8 ohm)  
speaker.  
¿ Internal/External speaker switch  
¹ DisplayPort connectors  
IN connector: To input DisplayPort signals.  
OUT connector: To output signal which is displayed.  
See page 24 VIDEO OUT SETTING.  
: Internal speaker  
: External speaker.  
NOTE: Please power off the monitor when you use the  
Internal/External speaker switch.  
To output signal which is displayed as a main picture when  
selected PIP mode. See page 11.  
´ AUDIO OUT  
To output the audio signal from the AUDIO IN 1, 2, DPORT  
and HDMI to an external device (stereo receiver, amplifier,  
etc.).  
Ƹ HDMI IN  
To input digital HDMI signals.  
² Service port  
This USB slot is for future software upgrades.  
ƹ DVI IN (DVI-D)  
To input digital RGB signals from a computer or HDTV device  
having a digital RGB output.  
LAN port (RJ-45)  
LAN connection. See page 31 and 34.  
* This connector does not support analog input.  
NOTE: Please give priority for use to LAN1.  
ƺ Kensington Lock  
For security and theft prevention.  
AUDIO IN 1, 2  
ƻ Option board slot  
Slot 2 and slot 3 type accessories are available.  
To input audio signal from external equipment such as a  
computer or DVD player.  
Please contact your supplier for detailed information.  
NOTE: Please contact your supplier for available option board.  
¾ RS-232C (D-Sub 9 pin)  
Connect RS-232C input from external equipment such as a PC  
in order to control RS-232C functions.  
Ƽ Internal speaker  
English-9  
Wireless Remote Control  
´ AUDIO INPUT button  
Selects audio input source [IN1], [IN2], [IN3]*2, [OPTION]*2,  
[HDMI], [DPORT], [HDMI2]*2, [DPORT2]*2, [DPORT3]*2.  
² OPTION MENU button*1  
KEYPAD  
Press buttons to set and change passwords, change channel  
and set REMOTE ID.  
º ENT button*1  
¾ DISPLAY button  
Turns on/off the information OSD. See page 18.  
µ MENU button  
Turns on/off the menu mode.  
¸ AUTO SET UP button  
Enters auto setup menu. See page 20.  
¹ EXIT button  
Returns to previous menu within OSD menu.  
Ƹ UP/DOWN button (  
/
)
Acts as button to move the highlighted area up or down  
to select adjustment items within OSD menu.  
Small screen which adjusted “PIP” mode moves up or down.  
ƹ MINUS/PLUS (-/+) button  
Increases or decreases the adjustment level within OSD  
menu settings.  
Small screen which adjusted “PIP” mode moves left or right  
and increases or decreases the size.  
³ POWER button  
Switches the power on/standby.  
· INPUT button  
ƺ SET/POINT ZOOM button  
Selects input signal.  
Makes selection. Activates POINT ZOOM function when OSD  
menu is not shown.  
DVI: DVI  
HDMI: HDMI, HDMI2*2  
DisplayPort: DPORT, DPORT2*2, DPORT3*2  
VGA: VGA  
ƻVOLUME UP/DOWN button (VOL +/-)  
Increases or decreases audio output level.  
Y/Pb/Pr: Y/Pb/Pr, SCART*2, Y/Pb/Pr2*2  
RGB/HV*2: RGB/HV  
Ƽ CH/ZOOM UP/DOWN button (CH/ZOOM +/-)*1  
Increases or decreases POINT ZOOM level.  
VIDEO*2: VIDEO, S-VIDEO  
OPTION: Depends on your connection  
ƽ GUIDE button*1  
» PICTURE MODE button  
Selects picture mode, [HIGHBRIGHT], [STANDARD],  
[sRGB], [CINEMA], [CUSTOM1], [CUSTOM2]. See page 18.  
ƾ MUTE button  
Turns on/off mute function.  
HIGHBRIGHT: for moving images such as DVD.  
STANDARD: for images.  
sRGB: for text based images.  
CINEMA: for movies.  
CUSTOM1 and CUSTOM2: activate auto dimming  
function. See page 28.  
ƿ STILL button  
ON/OFF button: Activates/deactivates still picture mode.  
STILL CAPTURE button: Captures still picture.  
NOTE: This function is released when activating IMAGE  
FLIP.  
IMAGE FLIP button  
¿ ASPECT button  
Toggle switches between H FLIP, V FLIP, 180° ROTATE and  
NONE. See page 21.  
Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1],  
[ZOOM] and [NORMAL]. See page 17.  
English-10  
PIP (Picture In Picture) button  
Operating Range for the Remote  
Control  
ON/OFF button: Toggle switches between PIP, POP,  
PICTURE BY PICTURE-ASPECT and PICTURE BY  
PICTURE-FULL. See page 22.  
INPUT button: Selects the “picture in picture” input signal.  
CHANGE button: Replaces to the main picture and sub  
picture.  
NOTE: Enable to change the sub picture size by pressing  
SET/POINT ZOOM button during PIP mode.  
Sub picture  
Point the top of the remote control toward the LCD monitor’s  
remote sensor during button operation.  
Use the remote control within a distance of about 7 m (23 ft.)  
from remote control sensor or at a horizontal and vertical  
angle of within 30° within a distance of about 3.5 m (10 ft.).  
Main picture Connector  
DP Out*5  
DPORT*3  
DVI  
Yes  
No  
HDMI  
Yes  
Yes  
No  
VGA  
Yes  
Yes  
Yes  
No  
Y/Pb/Pr  
Yes  
Yes  
Yes  
No  
OPTION  
Yes  
DPORT  
DVI  
DisplayPort  
DVI-D  
No  
DPORT  
Yes  
Yes  
DVI  
HDMI  
HDMI  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
HDMI 1  
VGA  
Yes  
Yes  
Yes  
Yes  
Yes  
-
D-Sub*4  
Y/Pb/Pr  
OPTION  
Yes  
No  
No  
Yes  
-
Option  
Yes  
Yes  
Yes  
No  
OPTION  
*3: When VIDEO OUT SETTING is ONN, DPORT ccannot bbe selectted as thhe sub piicture.  
*4: If VGA or Y/Pb/Pr is selected as the main picture, DP out iss disabbled eveen when  
VIDEO OUT SETTTING is ON.  
*5: DP out can output signal only when VIDEO OUT SETTTING iis ON.  
REMOTE ID button  
Activates REMOTE ID function.  
Caution: Important, the remote control  
system may not function  
MTS button*1  
button*1  
when direct sunlight or strong  
illumination strikes the remote  
control sensor or when there is  
an object in the path.  
Activates closed captioning.  
NOTE: VIDEO*2, S-VIDEO*2 inputs only.  
*1: This button’s action depends on which option board you use.  
Refer to the option board’s manual for further information.  
Handling the remote control  
*2: This function depends on which option board you use.  
Do not subject to strong shock.  
Do not allow water or other liquid to splash  
the remote control. If the remote control gets  
wet, wipe it dry immediately.  
Avoid exposure to heat and steam.  
Other than to install the batteries, do not open the remote  
control.  
English-11  
Setup  
NEC recommends the following battery use:  
1. Determine the installation location  
CAUTION: Installing your LCD monitor must be done by a  
qualified technician. Contact your dealer for more  
information.  
Place “AAA” size batteries matching the (+) and (-) signs  
on each battery to the (+) and (-) signs of the battery  
compartment.  
Do not mix battery brands.  
CAUTION: MOVING OR INSTALLING THE LCD MONITOR  
MUST BE DONE BY TWO OR MORE PEOPLE.  
Failure to follow this caution may result in injury if  
the LCD monitor falls.  
Do not combine new and old batteries. This can shorten  
battery life or cause liquid leakage of batteries.  
Remove dead batteries immediately to prevent battery  
acid from leaking into the battery compartment.  
CAUTION: Do not mount or operate the monitor upside  
Do not touch exposed battery acid, it may injure skin.  
down.  
NOTE:  
If you do not intend to use the Remote Control for  
a long period of time, remove the batteries.  
CAUTION: This LCD has a temperature sensor and cooling  
fan, including a fan for the option board.  
If the LCD becomes too hot, the cooling fan will  
turn on automatically.  
3. Connect external equipment  
(See pages 14 and 15)  
The option board’s fan is active although the  
temperature is lower than normal operating  
temperature for cooling the option board. If the  
LCD becomes overheated while the cooling fan  
is running, a “Caution” warning will appear. If the  
“Caution” warning appears, discontinue use and  
allow the unit to cool. Using the cooling fan will  
reduce the likelihood of early circuit failure and  
may help reduce image degradation and “Image  
Persistance”.  
If the LCD is used in an enclosed area or if the  
LCD panel is covered with a protective screen,  
please check the inside temperature of the  
monitor by using the “HEAT STATUS” control  
in the OSD (see page 25). If the temperature is  
higher than the normal operating temperature,  
please turn the cooling fan to ON within the FAN  
CONTROL menu within the OSD (see page 25).  
To protect the external equipment; turn off the main power  
before making connections.  
Refer to your equipment user manual for further  
information.  
NOTE:  
Do not connect/disconnect cables when turning  
on the monitor or other external equipment as this  
may result in a loss of the monitor image.  
4. Connect the supplied power cord  
The equipment should be installed close to an easily  
accessible power outlet.  
Please fasten power cord to the LCD monitor by attaching  
the screw and clamp.  
Fully insert the prongs into the power outlet socket.  
A loose connection may cause image degradation.  
NOTE:  
Please refer to the “Safety Precautions and  
Maintenance” section of this manual for proper  
selection of AC power cord.  
IMPORTANT: Lay the protective sheet, which was wrapped  
around the LCD monitor when it was  
packaged, beneath the LCD monitor so as not  
to scratch the panel.  
2. Install the remote control batteries  
The remote control is powered by two 1.5V AAA batteries.  
To install or replace batteries:  
Screw  
Clamp  
A. Press and slide to open the cover.  
B. Align the batteries according to the (+) and (–) indications  
inside the case.  
C. Replace the cover.  
CAUTION: Incorrect usage of batteries can result in leaks or  
bursting.  
English-12  
5. Switch on the power of all the attached  
external equipment  
When connected with a computer, switch on the power of the  
computer first.  
6. Operate the attached external equipment  
Display the signal from the desired input source.  
7. Adjust the sound  
Make volume adjustments when required.  
8. Adjust the screen (See pages 20 and 21)  
Make adjustments of the screen display position when  
necessary.  
9. Adjust the image (See page 20)  
Make adjustments such as backlight or contrast when  
required.  
10. Recommended Adjustments  
To reduce the risk of the “Image Persistence”, please adjust  
the following items based on the application being used:  
“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 25)  
“DATE & TIME”, “SCHEDULE SETTINGS” (See page 22).  
It is recommended that the “FAN CONTROL” setting  
(See page 25) be turned to ON also.  
English-13  
Connections  
NOTE:  
Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a  
loss of the monitor image.  
NOTE:  
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.  
Before making connections:  
*
*
First turn off the power of all the attached equipment and make connections.  
Refer to the user manual included with each separate piece of equipment.  
Wiring Diagram  
DVD Player  
Second monitor*  
Solid lines = video signal  
Dotted lines = audio signal  
Stereo Amplifier  
Computer (Analog)  
*: Multiple monitors that are daisy-chained have a limit to the connectable monitors.  
Computer (Digital)  
Connected  
equipment  
Connecting  
terminal  
DisplayPort  
DVI (DVI-D)  
HDMI  
VGA (D-Sub)  
VGA (D-Sub)  
Option  
DisplayPort  
DVI (DVI-D)  
HDMI  
Connecting  
audio terminal  
DPORT  
AUDIO IN1/IN2  
HDMI  
AUDIO IN1/IN2  
AUDIO IN1/IN2  
OPTION  
DPORT  
AUDIO IN1/IN2  
HDMI  
Input button  
Setting in terminal mode  
Input signal name  
in remote control  
DisplayPort  
DVI  
-
DP  
DVI  
HDMI  
DVI-HD  
RAW/EXPAND*1  
HDMI  
RGB/HV  
Y/Pb/Pr  
OPTION  
DisplayPort  
DVI  
AV  
D-SUB MODE RGB  
D-SUB MODE COMPONENT  
VGA  
COMPONENT  
OPTION  
DP  
-
-
DVI-PC  
DVI  
HDMI  
PC  
RAW/EXPAND*1  
HDMI  
VGA (D-Sub)  
Option  
-
-
VGA  
OPTION  
AUDIO IN1/IN2  
OPTION  
RGB/HV  
OPTION  
*1: depend on signal type.  
English-14  
Connecting a Personal Computer  
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.  
Some video cards may not display an image correctly.  
Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.  
<Typical factory preset signal timing>  
Scanning frequency  
Horizontal Vertical  
Remarks  
Resolution  
640 x 480  
800 x 600  
31.5 kHz  
37.9 kHz  
48.4 kHz  
48 kHz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
1024 x 768  
1280 x 768  
1360 x 768  
1280 x 1024  
1600 x 1200  
1920 x 1080  
48 kHz  
64 kHz  
75 kHz  
Compressed image  
67.5 kHz  
Recommended resolution  
If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook.  
Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any  
special identification or configuration your monitor’s image and monitor may require.  
Input TMDS signals conforming to DVI standards.  
To maintain display quality, use a cable that conforms to DVI standards.  
Connecting a DVD Player or Computer with HDMI out  
Please use an HDMI cable with HDMI logo.  
It may take a moment for the signal to appear.  
Some video cards or drivers may not display an image correctly.  
When you use a computer with HDMI out, please set OVER SCAN to “OFF” (see page 27).  
Connecting a Computer with DisplayPort  
Please use DisplayPort cable with DisplayPort compliance logo.  
It may take a moment for the signal to appear.  
Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not  
appear.  
Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.  
English-15  
Basic Operation  
Power ON and OFF Modes  
The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.  
NOTE:  
The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the  
Power Button on the front of the LCD.  
OFF  
Main Power Switch  
ON  
Power Button  
Using the remote control  
English-16  
Power Indicator  
Picture Aspect  
DVI, VGA, RGV/HV*4, DPORT, DPORT2*4, DPORT3*4  
Mode  
Status Indicator Light  
Green*1  
FULL  
1:1  
ZOOM  
NORMAL  
Power ON  
Power OFF and Power Save “AUTO Red  
POWER STANDBY”  
HDMI, Y/Pb/Pr, SCART*4, VIDEO*4, S-VIDEO*4, HDMI2*4, Y/Pb/Pr2*4  
Power consumption under 0.5 W  
FULL  
WIDE  
DYNAMIC  
1:1  
ZOOM  
NORMAL  
Power Save “AUTO POWER SAVE” Amber  
Power consumption under 2.5 W*2  
Aspect ratio  
of image  
Recommended selection  
for picture aspect*3  
Power Standby when “SCHEDULE  
SETTINGS” enabled  
Diagnosis (Detecting failure)  
Green and Amber blink alternately  
Unchanged view*3  
Red Blinking  
(See Troubleshooting page 46)  
NORMAL  
*1 If “OFF” is selected in POWER INDICATOR (page 24), the LED will not light when the  
LCD monitor is in active mode.  
*2 Without any option, with factory settings, VGA input only.  
4:3  
DYNAMIC  
FULL  
Using Power Management  
The LCD monitor follows the VESA approved DPM Display  
Power Management function.  
The power management function is an energy saving  
function that automatically reduces the power consumption  
of the display when the keyboard or the mouse has not been  
used for a fixed period.  
The power management feature on your new display has  
been set to the “AUTO POWER SAVE” mode. This allows  
your display to enter a Power Saving Mode when no signal is  
applied. This could potentially increase the life and decrease  
the power consumption of the display.  
Squeeze  
Letterbox  
WIDE  
*3 Grey areas indicate unused portions of the screen.  
NORMAL: Displays the aspect ratio the same as it is sent  
from the source.  
NOTE:  
Depending on the PC and video card used, this  
function may not operate.  
FULL: Fills entire screen.  
NOTE:  
The monitor automatically goes into OFF at the  
preset time period after signal is lost.  
WIDE: Expands a 16:9 letter box signal to fill entire screen.  
DYNAMIC: Expands a 4:3 pictures to fill the entire screen  
with non-linearity. Some of the outside image area will be cut  
off due to expansion.  
Selecting a video source*4  
To view a video source:  
Use the input button to set [VIDEO], [S-VIDEO].  
1:1: Displays the image in a 1 by 1 pixel format.  
ZOOM  
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],  
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your  
video format.  
The image can be expanded beyond the active display area.  
The image which is outside of active display area is not  
shown.  
ZOOM  
ZOOM  
*4: This function depends on which option board you use.  
English-17  
Information OSD  
The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc.  
Press the DISPLAY button on the remote to bring up the Information OSD.  
³
·
»
¿
Input Name  
Audio input mode  
Picture aspect  
Input Signal Information  
Sub picture information  
Picture Mode  
DVI, VGA, RGB/HV*, DPORT, DPORT2*, DPORT3*  
STANDARD  
sRGB  
CUSTOM1  
CUSTOM2  
HIGHBRIGHT  
HDMI, Y/Pb/Pr, SCART*, VIDEO*, S-VIDEO*, HDMI2*, Y/Pb/Pr2*  
STANDARD  
CINEMA  
CUSTOM1  
CUSTOM2  
HIGHBRIGHT  
*: This function depends on which option board you use.  
English-18  
OSD (On-Screen-Display) Controls  
NOTE:  
Some functions may not be available depending on the model or optional equipment.  
Input source  
Main Menu Icons  
Main Menu Item  
70  
50  
50  
50  
Adjustment Settings  
50  
Sub Menu  
50  
THANK YOU FOR SAVING  
THE ENVIRONMENT.  
CARBON FOOTPRINT  
86.0 %  
PICTURE MODE  
Goto Adjustment Return  
Close  
Select  
Key Guide  
Press UP or DOWN  
button to select  
sub-menu.  
Press SET/POINT  
ZOOM.  
Press UP or DOWN,  
PLUS or MINUS to select  
the function or setting to  
be adjusted.  
Press MENU or EXIT.  
Remote Control  
Press UP or DOWN  
button to select.  
Press INPUT button  
to decide.  
Press UP or DOWN, PLUS  
or MINUS button to select.  
Press EXIT  
Control Panel  
OSD screen  
English-19  
Setting  
Default  
PICTURE  
BACKLIGHT  
Adjusts the overall image and background brightness. Press + or - to adjust.  
NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be  
changed.  
70  
CONTRAST  
Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.  
NOTE: When sRGB is selected in picture mode, this function cannot be changed.  
50  
SHARPNESS  
BRIGHTNESS  
Adjusts the crispness of the image. Press + or - to adjust.  
50*2  
50  
Adjusts the image brightness in relationship to the background. Press + or - to adjust.  
NOTE: When sRGB is selected in picture mode, this function cannot be changed.  
HUE  
Adjusts the hue of the screen. Press + or - to adjust.  
50  
NOTE: When sRGB is selected in picture mode, this function cannot be changed.  
COLOR  
Adjusts the color depth of the screen. Press + or - to adjust.  
50*2  
NOTE: When sRGB is selected in picture mode, this function cannot be changed.  
COLOR TEMPERATURE  
Adjusts the color temperature of the entire screen. A low color temperature will make the screen  
reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further  
adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B  
levels, CUSTOM must be showing as the COLOR TEMP selection.  
10000K  
NOTE: When sRGB is selected in picture mode, predefined 6500k is set so it cannot be changed.  
When PROGRAMMABLE1, PROGRAMMABLE2 or PROGRAMMABLE3 is selected in GAMMA  
CORRECTION, this function cannot be changed.  
COLOR CONTROL  
Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.  
NOTE: When sRGB is selected in picture mode, this function cannot be changed.  
When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function cannot be  
changed.  
0
GAMMA CORRECTION  
Select a display gamma for best picture quality.  
NOTE: When sRGB is selected in picture mode, this function cannot be changed.  
NATIVE*2  
(except sRGB  
setting)  
NATIVE  
2.2  
Gamma correction is handled by the LCD panel.  
Typical display gamma for use with a PC.  
Good for video (DVD, etc.)  
2.4  
S GAMMA  
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the  
image (S-Curve).  
DICOM SIM.  
DICOM GSDF curve simulated for LCD type.  
PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using NEC optional software.  
MOVIE SETTINGS  
NOTE: When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function  
cannot be changed.  
NOISE REDUCTION*1 Adjusts the amount of noise reduction. Press + or - to adjust.  
0*2  
VIDEO, S-VIDEO inputs only  
TELECINE  
Automatically senses the sources frame rate for optimal picture quality.  
AUTO*2  
HDMI, Y/Pb/Pr, SCART*1, VIDEO*1,  
S-VIDEO*1, HDMI2*1, Y/Pb/Pr2*1 inputs only  
ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast.  
S-VIDEO*1, HDMI2*1, Y/Pb/Pr2*1 inputs only  
OFF  
HDMI, Y/Pb/Pr, SCART*1, VIDEO*1,  
PICTURE MODE  
RESET  
Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1] or  
[CUSTOM2]. See page 18.  
STANDARD  
-
Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,  
CONTRAST, SHARPNESS, BRIGHTNESS, HUE, COLOR, COLOR TEMPERATURE,  
COLOR CONTROL, GAMMA CORRECTION, MOVIE SETTINGS.  
ADJUST  
AUTO SETUP  
Automatically adjusts Screen Size, H position, V position, Clock, Phase and White Level.  
H Position, V Position and Phase are adjusted automatically when new timing is detected.  
-
OFF  
-
VGA, RGB/HV*1 inputs only  
AUTO ADJUST  
VGA, RGB/HV*1 inputs only  
H POSITION  
Controls the horizontal position of the image within the Display area of the LCD.  
Press + to move right. Press - to move left.  
All inputs except DVI, HDMI, DPORT  
V POSITION  
Controls the vertical position of the image within the Display area of the LCD.  
Press + to move up. Press - to move down.  
-
-
All inputs except DVI, HDMI, DPORT  
CLOCK  
Press + to expand the width of the image on the right of the screen.  
Press - to narrow the width of the image on the left.  
VGA, RGB/HV*1 inputs only  
*1: This function depends on which option board you use.  
*2: Depends on signal input.  
English-20  
PHASE  
Adjusts the visual “noise” on the image.  
-
VGA, RGB/HV*1, Y/Pb/Pr, SCART*1, Y/Pb/Pr2*1  
inputs only  
H RESOLUTION  
Adjusts the horizontal size of the image.  
Adjusts the vertical size of the image.  
-
-
VGA, RGB/HV*1 inputs only  
V RESOLUTION  
VGA, RGB/HV*1 inputs only  
INPUT RESOLUTION  
If there is a problem with signal detection, this function forces the monitor to display the signal at  
the desired resolution. After selection, execute “AUTO SETUP” if required.  
If no problem is detected, the only available option will be “AUTO”.  
AUTO  
VGA, RGB/HV*1 inputs only  
ASPECT  
Select the aspect ratio of the screen image.  
FULL  
NOTE: When the ASPECT is DYNAMIC, WIDE or ZOOM, the image will be changed FULL  
image before IMAGE FLIP, then start to IMAGE FLIP.  
When the ASPECT is DYNAMIC or ZOOM, the image will be changed FULL image before TILE  
MATRIX, then start to TILE MATRIX. After TILE MATRIX, the ASPECT will be returned previous  
ASPECT or set ASPECT during TILE MATRIX.  
When the ASPECT is DYNAMIC or ZOOM, the image will be changed FULL image before POINT  
ZOOM, then start to POINT ZOOM. After POINT ZOOM, the ASPECT will be returned previous  
ASPECT. When the ASPECT is changed during POINT ZOOM, DYNAMIC and ZOOM will be  
FULL image.  
NORMAL  
FULL  
Displays the aspect ratio the same as it is sent from the source.  
Fills entire screen.  
-
-
-
-
WIDE  
Expands a 16:9 letter box signal to fill entire screen.  
DYNAMIC  
Expands a 4:3 pictures to fill the entire screen with non-linearity. Some of the outside image area  
will be cut off due to expansion. TILE MATRIX becomes invalid.  
1:1  
Display the image in a 1 by 1 pixel format. (If the input resolution is higher than a 1920 x 1080  
resolution, the image will be scaled down to fit the screen). TILE MATRIX becomes invalid.  
-
-
-
ZOOM  
The image can be expanded beyond the active display area. The image which is outside of active  
display area is not shown.  
ZOOM  
HZOOM  
Maintains the aspect ratio while zooming.  
Amount of horizontal zoom.  
Amount of vertical zoom.  
Horizontal position.  
VZOOM  
H POS  
V POS  
Vertical position.  
IMAGE FLIP  
NOTE: OVER SCAN is disabled when IMAGE FLIP is selected.  
-
When the ASPECT is DYNAMIC, WIDE or ZOOM, the image will be changed FULL image before  
IMAGE FLIP, then start to IMAGE FLIP.  
When selecting IMAGE FLIP except for NONE, following functions are released: PIP MODE,  
TILE MATRIX, SUPER in INPUT CHANGE, STILL, POINT ZOOM.  
IMAGE FLIP  
Display the inverse image right-left, up-down or rotation.  
Press + or - to select.  
NONE  
NONE  
H FLIP  
-
Normal mode.  
-
The image inverts right-left.  
The image inverts up-down.  
The image rotates 180 degrees.  
V FLIP  
-
-
180° ROTATE  
OSD FLIP  
Determines the OSD display direction.  
OFF  
If “ON” is selected, OSD will invert depending on the image.  
RESET  
Resets “ADJUST” settings back to factory settings.  
Increases or decreases output volume level.  
-
AUDIO  
VOLUME  
BALANCE  
40  
Select “STEREO” or “MONO” of audio output.  
CENTER,  
STEREO  
If you select “STEREO”, adjust the balance of L/R volume.  
Press + button to move the stereo sound image to right.  
Press - button to move the stereo sound image to left.  
TREBLE  
To accentuate or reduce the high frequency sound.  
Press + button to increase TREBLE sound.  
Press - button to decrease TREBLE sound.  
0
*1: This function depends on which option board you use.  
English-21  
BASS  
To accentuate or reduce the low frequency sound.  
Press + button to increase BASS sound.  
Press - button to decrease BASS sound.  
0
SURROUND  
Artificial surround sound.  
OFF  
NOTE: Audio out is disabled when this function is set to ON.  
PIP AUDIO  
LINE OUT  
Selects source of PIP audio.  
MAIN AUDIO  
FIXED  
Selecting “VARIABLE” enables control of the line out level with the VOLUME button.  
NOTE: Audio out is disabled when this function is set to ON.  
AUDIO INPUT  
Selects audio input source [IN1], [IN2], [IN3]*1, [OPTION]*1, [HDMI], [DPORT], [HDMI2]*1,  
[DPORT2]*1, [DPORT3]*1.  
Depend on  
signal input  
RESET  
Resets “AUDIO” options back to factory settings except VOLUME.  
-
SCHEDULE  
OFF TIMER  
Sets the monitor to power off after a length of time.  
A time between 1 to 24 hours is available.  
OFF  
SCHEDULE SETTINGS  
SCHEDULE LIST  
DATE & TIME  
Creates a working schedule for the monitor to use.  
List of schedules.  
-
-
Sets the date, time, and daylight saving region. Date & time must be set in order for the  
“SCHEDULE” function to operate. See page 29.  
YEAR  
MONTH  
Configures the year for the real-time clock.  
Configures the month for the real-time clock.  
Configures the day for the real-time clock.  
Configures the time for the real-time clock.  
Configures daylight savings on or off.  
-
-
DAY  
-
TIME  
-
OFF  
-
DAYLIGHT SAVING  
RESET  
Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER,  
SCHEDULE SETTINGS.  
PIP  
KEEP PIP MODE  
Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.  
When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.  
OFF  
OFF  
PIP MODE  
Selects Picture-in-Picture mode.  
NOTE: This function is released when selecting IMAGE FLIP except for NONE.  
OFF  
PIP  
Normal mode.  
Picture in Picture mode.  
Picture out Picture mode.  
POP  
PICTURE BY PICTURE- Picture by picture (split screen) mode, with keep aspect.  
ASPECT  
PICTURE BY PICTURE  
FULL  
-
Picture by picture (split screen) mode, with full screen.  
SUB INPUT  
Selects sub picture input signal.  
Depends on  
signal input  
PIP SIZE  
Determines the size of the sub-picture used in Picture-in-Picture (PIP) mode.  
Press the SET/POINT ZOOM button to adjust. Press + or CH+ to expand. Press - or CH- to  
reduce.  
37  
It is also possible to change the sub-picture size by pressing the SET/POINT ZOOM button when  
the sub-picture is shown.  
PIP POSITION  
ASPECT  
TEXT TICKER  
MODE  
Determines the location where the PIP appears on the screen.  
X = 95, Y = 92  
FULL  
Selects sub picture aspect, [FULL], [NORMAL] and [WIDE]. See page 17.  
OFF  
Enables Text Ticker and allows you to set Horizontal or Vertical direction.  
Selects the location of the Text Ticker on the screen.  
POSITION  
SIZE  
Determines the size of the Text Ticker in relationship to the overall screen size.  
Sets the transparency of the Text Ticker (0: transparent, 100: opaque).  
Enables auto-detection of the Text Ticker.  
BLEND  
DETECT  
FADE IN  
Enables fade-in of the text ticker.  
*1: This function depends on which option board you use.  
English-22  
RESET  
Resets PIP options back to factory settings except SUB INPUT and ASPECT.  
Select the language used by the OSD.  
-
OSD  
LANGUAGE  
ENGLISH  
DEUTSCH  
FRANÇAIS  
ITALIANO  
ESPAÑOL  
SVENSKA  
РУССКИЙ  
ENGLISH  
(Depends on  
destination)  
MENU DISPLAY TIME  
OSD POSITION  
UP  
Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.  
Determines the location where the OSD appears on the screen.  
30 SEC.  
X = 128, Y = 225  
DOWN  
RIGHT  
LEFT  
INFORMATION OSD  
Selects whether the information OSD is displayed or not. The information OSD will be displayed  
when the input signal or source changes. The information OSD will also give a warning when  
there is no-signal or the signal is out-of range.  
ON, 3 SEC.  
An interval between 3 to 10 seconds for the Information OSD to appear is available.  
MONITOR INFORMATION Indicates the model and serial number of your monitor and firmware version.  
CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon  
footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).  
CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the  
arithmetic estimation, not actual measurement value. This estimation is based without any  
options.  
-
OSD TRANSPARENCY  
OSD ROTATION  
LANDSCAPE  
Set the transparency of the OSD.  
OFF  
Determines the OSD display direction between landscape and portrait.  
Display the OSD with landscape mode.  
LANDSCAPE  
PORTRAIT  
Display the OSD with portrait mode.  
INPUT NAME  
You can create a name for the INPUT currently being used.  
-
Max: 8 characters, including Space, A-Z, 0-9, and some symbols.  
MEMO  
RESET  
Sets a title and message via HTTP server. See page 42.  
-
-
Resets the following settings within the OSD menu back to factory setting:  
MENU DISPLAY TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY.  
MULTI DISPLAY  
ID CONTROL  
Sets the monitor ID number from 1-100 and group ID from A-J. DETECTED MONITORS shows  
the number of all monitors which follow in the chain with LAN.  
1
NOTE: Group ID is made of multiple selections.  
AUTO ID  
When “YES” is selected, monitor ID numbers are set automatically in all monitors which follow in  
the chain with LAN.  
NO  
NOTE: All monitors which follow in the chain with LAN should be ON. When executing this  
function while in standby mode or power save mode, “LAN POWER” should be ON.  
AUTO ID RESET  
Resets monitor ID number of all monitors which follow in the chain with LAN.  
NOTE: AUTO ID RESET should be done when changes the number of monitors which follow in  
the chain with LAN.  
NO  
IR LOCK SETTING  
Selects the mode of the monitor for use with the infra-red remote control.  
UNLOCK  
Selects “LOCK” to prevent the monitor from being controlled by the wireless remote controller. To  
return to normal operation, press the “DISPLAY” button on the remote controller for 5 seconds.  
English-23  
TILE MATRIX  
Allows one image to be expanded and displayed over multiple screens (up to 100) through a  
distribution amplifier.  
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate  
without a distribution amplifier at a lower number of screens.  
NOTE: This function is released when selecting IMAGE FLIP except for NONE.  
When “DYNAMIC” or “ZOOM” is selected in ASPECT while executing TILE MATRIX, the setting  
will be applied after completing of TILE MATRIX.  
H MONITORS  
V MONITORS  
POSITION  
Number of monitors arranged horizontally.  
1
Number of monitors arranged vertically.  
1
Select which section of the tiled image to be displayed on the monitor.  
Turns the TILE COMP feature on.  
1
NO  
TILE COMP  
ENABLE  
Enables Tile Matrix.  
NO  
TILE MATRIX MEM  
When “INPUT” is selected, TILE MATRIX setting is applied to each signal input.  
COMMON  
AUTO TILE MATRIX  
SETUP  
Allows auto setting of multiple screens by inputting the number of monitors arranged horizontally DEACTIVATE  
and vertically on the primary monitor. Following settings are set automatically: MONITOR  
ID, TILE MATRIX, TILE MATRIX MEM, Input Signal, VIDEO OUT SETTING, DisplayPort in  
TERMINAL SETTING.  
NOTE: All monitors which follow in the chain with LAN should be ON. When executing this  
function while in standby mode or power save mode, “LAN POWER” should be set to ON.  
AUTO ID will be automatically executed. When you use this function, it is recommended that  
monitors are chained by DisplayPort cable.  
Example of installation via LAN:  
Primary monitor  
H MONITORS  
V MONITORS  
3
3
POWER ON DELAY  
DELAY TIME  
Adjusts the delay time between being in “standby” mode and entering “power on” mode.  
“POWER ON DELAY” can be set between 0 and 50 seconds.  
0 SEC.  
OFF  
LINK TO ID  
When “ON” selected, delay time is linked with Monitor ID. It takes more time as larger ID number.  
VIDEO OUT SETTING  
Enables the signal output from DPORT. See also page 26 “DisplayPort” in TERMINAL SETTING.  
NOTE: When VGA or Y/Pb/Pr is selected as the main picture, nothing will be output from DPORT.  
When this function is ON, DPORT cannot be selected as the sub picture. When this function is  
ON, INPUT CHANGE is limited to be NORMAL or QUICK. When this function is ON and DPORT  
is selected as the main picture, PIP CHANGE button of remote control (see page 11) is disabled.  
ON  
POWER INDICATOR  
SETTING COPY  
Turns ON or OFF the LED located at the front of the monitor.  
If “OFF” is selected, LED will not light when the LCD monitor is in active mode.  
ON  
NO  
In a daisy chain scenario, select the OSD menu categories that you want to copy over to the  
other monitor.  
NOTE: When you use this function, monitors should be daisy chained by LAN. This function  
resets to default when power is off. This function has a limit depending on the cable you use.  
COPY START  
ALL INPUT  
RESET  
Select “YES” and press the SET button to start copying.  
All input terminals settings are copied when you select this item. Default is off.  
Resets “MULTI DISPLAY” options back to factory settings except for POWER ON DELAY and  
VIDEO OUT SETTING.  
-
DISPLAY PROTECTION  
POWER SAVE  
Sets how long the monitor waits to go into power save mode after the signal is lost.  
AUTO  
NOTE: When connecting DVI, the video card might not stop sending the digital data even  
though the image might have disappeared. If this occurs the monitor will not switch into power  
management mode. POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in  
HUMAN SENSING.  
STANDBY  
AUTO POWER SAVE  
AUTO STANDBY  
DISABLE  
The monitor automatically goes into OFF at the preset time period after signal is lost.  
The monitor will return to normal mode when signal is restarted.  
-
-
-
The monitor automatically goes into OFF at the preset time period after signal is lost.  
Press the power button to return to normal mode.  
The monitor will not goes into OFF after signal is lost.  
English-24  
HEAT STATUS  
FAN CONTROL  
Displays status of the FAN, BACKLIGHT and TEMPERATURE.  
-
Cooling fan reduces the temperature of the display to protect from overheating.  
AUTO, HIGH  
If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.  
SCREEN SAVER  
GAMMA  
Use the SCREEN SAVER function to reduce the risk of Image Persistence.  
The display gamma is changed and fixed when “ON” is selected.  
OFF  
OFF  
BACKLIGHT  
The brightness of backlight is decreased when “ON” is selected.  
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.  
MOTION  
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at  
user determined intervals. You can set interval time and zooming ratio.  
This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.  
OFF  
15  
-
SIDE BORDER COLOR  
CHANGE PASSWORD  
Adjusts the color of the side borders when a 4:3 image is displayed.  
Press + button, the bar will become lighter.  
Press - button, the bar will become darker.  
Allows the security password to be changed.  
The factory preset password is 0000.  
SECURITY  
RESET  
Locks the security password.  
OFF  
-
Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:  
POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR.  
EXTERNAL CONTROL  
IP ADDRESS SETTING  
NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN  
SETTING is applied.  
IP SETTING  
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.  
Disabling this option allows you to register the IP address or subnet mask number obtained from  
your network administrator.  
AUTO  
NOTE: Consult your network administrator for the IP address when “AUTO” is selected for  
[IP SETTING].  
IP ADDRESS:  
Set your IP address of the network connected to the monitor when “MANUAL” is selected for  
[IP SETTING].  
192.168.0.10  
255.255.255.0  
0.0.0.0  
SUBNET MASK:  
DEFAULT GATEWAY:  
Set your subnet mask number of the network connected to the monitor when “MANUAL” is  
selected for [IP SETTING].  
Set your default gateway of the network connected to the monitor when “MANUAL” is selected  
for [IP SETTING].  
NOTE: Set as [0.0.0.0] to delete the setting.  
DNS  
Set for IP ADDRESS setting of DNS server.  
AUTO  
AUTO: Automatically assign an IP address of DNS server connected to the monitor.  
MANUAL: Set your IP address of DNS server connected to the monitor.  
DNS PRIMARY:  
Set your primary DNS settings of the network connected to the monitor.  
NOTE: Set as [0.0.0.0] to delete the setting.  
0.0.0.0  
0.0.0.0  
DNS SECONDARY:  
Set your secondary DNS settings of the network connected to the monitor.  
NOTE: Set as [0.0.0.0] to delete the setting.  
MAC ADDRESS  
LAN POWER  
Displays the MAC ADDRESS.  
-
Selects LAN operation mode. When “ON” selected, allows to supply power to LAN during power  
save mode or standby mode.  
OFF  
NOTE: For enabling “AUTO ID” or “AUTO TILE MATRIX SETUP”, this function should be ON.  
DDC/CI  
PING  
ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.  
Confirm the response by communicating to the preset IP address.  
ENABLE  
192.168.0.10  
NO  
IP ADDRESS RESET  
RESET  
Resets IP ADDRESS SETTING back to factory settings.  
NO  
-
Resets the following setting within the EXTERNAL CONTROL menu back to factory settings:  
DDC/CI.  
English-25  
ADVANCED OPTION1  
INPUT DETECT  
Selects the method of input detection the monitor uses when more than two input devices are  
connected.  
NONE  
NOTE: When SUPER is selected in INPUT CHANGE, this function cannot be changed.  
NONE  
The Monitor will not search the other video input ports.  
FIRST DETECT*2  
When the current video input signal is not present, then the monitor searches for a video signal  
from the other video input port. If the video signal is present in the other port, then the monitor  
switches the video source input port to the new found video source automatically.  
The monitor will not look for other video signals while the current video source is present.  
LAST DETECT*2  
When the monitor is displaying a signal from the current source and a new secondary source  
is supplied to the monitor, the monitor will automatically switch to the new video source. When  
current video input signal is not present, the monitor searches for a video signal from the other  
video input port. If the video signal is present in the other port, then the monitor switches the  
video source input port to the new found video source automatically.  
VIDEO DETECT  
Y/Pb/Pr, Y/Pb/Pr2*1, SCART*1, VIDEO*1 or S-VIDEO*1 inputs will have priority over DVI, VGA,  
RGB/HV*1. When Y/Pb/Pr, Y/Pb/Pr2*1, SCART*1, VIDEO*1 or S-VIDEO*1 input signal is present  
the monitor will change and keep to the Y/Pb/Pr, Y/Pb/Pr2*1, SCART*1, VIDEO*1 or S-VIDEO*1  
input.  
CUSTOM DETECT  
Set the priority of input signals.  
When CUSTOM DETECT is selected, monitor searches listed inputs only.  
LONG CABLE COMP*1  
Manually compensates for image degradation caused from using a long cable.  
(Analog input only)  
ON/OFF  
ON: Activates this function.  
OFF: Deactivates this function.  
OFF  
0
SOG PEAK  
Adjusts the sensitivity of the Sync On Green input signals. Adjusts the slice level when separating  
synchronization from sync On Green signal input. Press “LEFT” or “RIGHT” to select.  
GAIN  
Adjusts gain value.  
0
R-H.POSITION  
G-H.POSITION  
B-H.POSITION  
Adjusts the position of the red component of the image.  
Adjusts the position of the green component of the image.  
Adjusts the position of the blue component of the image.  
0
0
0
SYNC TERMINATION Selects the terminate resistance for matching the cable impedance.  
HIGH  
NORMAL  
INPUT CHANGE  
Sets input change speed. When selected “SUPER”, allows to switch high-speed between set two  
signals.  
NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.  
“SUPER” is released when selecting IMAGE FLIP except for NONE.  
This function should be chosen after all adjustment options have been made for the input.  
TERMINAL SETTING  
DVI MODE  
Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC” when  
PC or other computer equipment is connected. Select “DVI-HD” when DVD player, which has  
DVI-D output, is connected.  
DVI-PC  
RGB  
D-SUB MODE  
Selects the type of signal associated with the D-SUB input.  
RGB: Analog input (R, G, B, H, V)  
COMPONENT: Component (Y, Cb/Pb, Cr/Pr)  
BNC MODE*1  
Selects the kind of equipment which is connected to the BNC input.  
RGB: Analog input.  
RGB  
COMPONENT: Component.  
SCART MODE*1  
Input mode for devices using SCART connectors.  
OFF  
1.1a  
DisplayPort  
Selects DisplayPort mode [1.1a] or [1.2].  
[1.2] should be selected when using Multi-Stream Transport.*3  
HDMI SIGNAL  
RAW: Disable the expanded feature.  
EXPAND  
EXPAND: Expand image contrast and increase detail in the dark and bright areas.  
*1: This function depends on which option board you use.  
*2: Only for DVI, DPORT, VGA, RGB/HV*1, HDMI, HDMI2*1, DPORT2*1, DPORT3*1 input.  
*3: Multi-Stream Transport requires the corresponding video card.  
English-26  
DEINTERLACE  
Selects the IP (Interlace to Progressive) conversion function.  
ON  
NOTE: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu. When INPUT2 of  
SUPER is selected in INPUT CHANGE and displayed, this function cannot be changed.  
ON  
Converts interlaced signals to progressive. This is the default setting.  
OFF  
Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of  
image retention.  
COLOR SYSTEM*1  
The selected Color System depends on the video format of the input signal.  
AUTO  
VIDEO, S-VIDEO inputs only  
AUTO  
NTSC  
Automatically chooses Color System setting based on input signal.  
PAL  
SECAM  
4.43 NTSC  
PAL-60  
OVER SCAN  
Some video formats may require different scanning modes in order to best display the image.  
ON  
HDMI, Y/Pb/Pr, SCART*1, VIDEO*1, S-VIDEO*1,  
HDMI2*1 inputs only  
ON  
Image size is larger than what can be displayed. The image edge will appear cropped.  
Approximately 95% of the image will be shown on the screen.  
OFF  
Image size stays within the display area. The whole image is displayed on the screen.  
NOTE: When you use a computer with HDMI out, please set “OFF”.  
OPTION SETTING  
OPTION POWER  
You can set this setting when option board accessory is connected to the monitor.  
Please contact your supplier for detailed information about Option board slot accessories.  
-
Allow the monitor to supply power to Option board slot during power save mode or standby  
OFF  
mode.  
NOTE: This function should be set to ON when using power save management by slot 2 type  
option.  
AUDIO  
The function is available for slot 2 type option. Selects sound input signal according to slot2 type  
option’s specifications. To activate DIGITAL, select OPTION for input signal and OPTION for  
AUDIO INPUT.  
ANALOG  
NOTE: DIGITAL is activated only when OPTION is selected for input signal and OPTION for  
AUDIO INPUT.  
INTERNAL PC  
OFF WARNING  
The function is available for slot 2 type PC.  
If OPTION POWER is OFF, a warning message appears when monitor power is turned off.  
NOTE: Warning message does not appear when monitor power is turned off by OFF TIMER  
setting or SCHEDULE setting.  
OFF  
OFF  
AUTO OFF  
Monitor power is automatically “OFF” when connected PC is OFF or the monitor is in power save  
mode.  
NOTE: Monitor power is not automatically “ON” when connected PC is ON.  
START UP PC  
FORCE QUIT  
When ON is selected, connected PC start-up.  
NO  
NO  
When ON is selected, it performs force-quit PC.  
Please use this function only when the operating system cannot be shut down manually.  
120Hz  
(not adjustable)  
-
-
-
TOUCH PANEL  
RESET  
(not adjustable)  
Resets the following settings within the ADVANCED OPTION menu back to factory setting:  
INPUT DETECT (except the priority of input signals), INPUT CHANGE (except for INPUT1 and  
INPUT2), TERMINAL SETTING, DEINTERLACE, COLOR SYSTEM, OVER SCAN, AUDIO in  
OPTION SETTING.  
*1: This function depends on which option board you use.  
English-27  
ADVANCED OPTION2  
AUTO DIMMING  
Adjusts the backlight of the LCD automatically depending on the amount of ambient light.  
-
AUTO BRIGHTNESS  
DPORT, DVI, VGA, RGB/HV*1, DPORT2*1,  
DPORT3*1 inputs only  
Adjusts the brightness level according to the input signal.  
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.  
OFF  
ROOM LIGHT  
SENSING  
The backlight of the LCD screen can be set to increase or decrease depending on the amount of  
ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If  
the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the  
viewing experience more comfortable to the eye in a variety of lighting conditions.  
NOTE: When ROOM LIGHT SENSING is set to MODE1 or MODE2, BACKLIGHT, AUTO  
BRIGHTNESS and BACKLIGHT in SCREEN SAVER function are disabled.  
OFF  
Do not cover the room light sensing sensor when you use MODE1 or MODE2.  
AMBIENT parameter setting  
ROOM LIGHT SENSING in OSD, select MODE1 or MODE2 and set MAX LIMIT, IN BRIGHT and  
IN DARK in each mode.  
MAX LIMIT: This is the max level of backlight which you set.  
IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is  
highest.  
IN DARK: This is the level of backlight that the monitor will go down to when the ambient light  
level is low.  
When the ROOM LIGHT SENSING is enabled the Backlight level of the screen changes  
automatically according to the lighting conditions of the room (see figure below).  
Factory Setting  
BACKLIGHT range  
BACKLIGHT range when  
set to MAX LIMIT.  
BACKLIGHT level set for  
the monitor to use when  
ambient lighting level is  
low.  
BACKLIGHT level set  
for the monitor to use  
when ambient lighting  
level is high.  
IN DARK  
dark  
IN BRIGHT  
room bright condition  
bright  
Screen Backlight value by MODE1  
Screen Backlight value by MODE2  
MAX LIMIT: BACKLIGHT level is limited to your set level.  
IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.  
IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.  
HUMAN SENSING*2  
HUMAN SENSING has three settings.  
DISABLE  
NOTE: POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in HUMAN  
SENSING.  
DISABLE  
No human sensing.  
-
-
AUTO OFF  
At the preset time, when no person is detected, BACKLIGHT and VOLUME automatically go  
into OFF. When a person comes near the monitor again, the monitor will automatically return to  
normal mode.  
CUSTOM  
BACKLIGHT and VOLUME automatically shift to the set value when detecting no person. When  
a person comes near the monitor again, the monitor automatically return to normal mode and  
display the input signal selected in INPUT SELECT.  
-
INTELLI. WIRELESS DATA Select “ON” to activate INTELLIGENT WIRELESS DATA function (see page 44). A password is  
required when using the function.  
ON  
RESET  
Resets “ADVANCED OPTION 2” settings back to factory setting, except for INTELLI. WIRELESS  
DATA.  
-
-
FACTORY RESET  
Resets OSD options back to factory settings EXCEPT FOR: PICTURE MODE, VOLUME,  
SCHEDULE SETTINGS, DATE & TIME, DAYLIGHT SAVINGS, SUB INPUT in PIP, ASPECT  
in PIP, LANGUAGE, OSD ROTATION, MEMO, POWER ON DELAY, CHANGE PASSWORD,  
SECURITY, IP ADDRESS SETTING, LAN POWER, PING and LONG CABLE COMP.  
*1: This function depends on which option board you use.  
*2: The function is available only when connecting the optional control unit.  
English-28  
NOTE 1: CREATING A SCHEDULE  
The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed.  
To program the schedule:  
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET/POINT ZOOM or the + button  
to enter the Settings menu. Highlight the desired schedule number and press SET/POINT ZOOM. The box next to the number will turn yellow.  
The schedule can now be programmed.  
2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to  
highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.  
3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight  
PIC. MODE. Use the + and - buttons to choose the picture mode.  
4. Use the down button to select a day on which the schedule will be enabled. Push the  
SET/POINT ZOOM button to enable. If the schedule is to be ran every day, choose  
EVERY DAY and press the SET/POINT ZOOM button. The circle next to EVERY DAY  
will turn yellow. If a weekly schedule is desired, choose the days of the week using the up OFF TIMER  
and down buttons and pressing SET/POINT ZOOM to select. Then highlight the EVERY  
WEEK option and press SET/POINT ZOOM.  
DVI  
SCHEDULE:  
(THU) JUN.18.2009 15:38  
SETTINGS:  
1
2
3
4
5
6
7
SCHEDULE SETTINGS  
SCHEDULE LIST  
DATE & TIME  
RESET  
ON:  
– – : – –  
– – : – –  
– – – –  
– – – –  
OFF:  
INPUT:  
PIC. MODE:  
5. After a schedule is programmed the remaining schedules can then be set. Press MENU  
to leave the OSD or press EXIT to go back to the previous menu.  
EVERY DAY  
EVERY WEEK  
MON  
TUE  
FRI  
WED  
SAT  
THU  
SUN  
NOTE: If schedules are overlapping then the schedule with the highest number will have  
priority over the schedule with the lowest number. For example schedule #7 will have  
priority over schedule #1.  
Return  
Close  
Choose  
Mark  
If selected input or picture mode is not available now, disable input or picture mode  
is shown in red.  
NOTE 2: IMAGE PERSISTENCE  
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a  
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not  
permanent, but constant images being displayed for a long period of time should be avoided.  
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the  
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.  
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at  
regular intervals whenever the screen is idle or turning off the monitor when not in use.  
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.  
For long life use as Public Display  
Image Sticking of LCD Panel  
When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or  
“ghost” image of previous image may be observed. (Image Persistence)  
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along the  
displayed image, and may be permanent. (Image Sticking)  
Recommendations  
To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.  
1. Fixed image should not be displayed for long period. Change fixed images after short intervals.  
2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.  
3. Lower environmental temperatures prolong the lifespan of the monitor.  
When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are  
stacked, utilize the temperature sensors inside monitor.  
To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.  
4. Please use “Screen Saver Mode” of monitor.  
English-29  
Remote Control Function  
REMOTE CONTROL ID FUNCTION  
Monitor ID:1  
Monitor ID:2  
Monitor ID:3  
REMOTE CONTROL ID  
The remote control can be used to control up to 100 individual MultiSync monitors using  
what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode  
works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync  
monitors. For example: if there are many monitors being used in the same area, a remote  
control in normal mode would send signals to every monitor at the same time (see  
Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one specific  
monitor within the group (see Figure 2).  
Remote works  
Remote works  
Remote works  
Figure 1  
Remote in  
Normal mode or  
the REMOTE ID  
is set to 0  
TO SET REMOTE CONTROL ID  
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to  
input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then  
be used to operate the monitor having that specific Monitor ID number.  
When 0 is selected or when the remote control is in normal mode, all monitors will be  
operated.  
Monitor ID:1  
Monitor ID:2  
Monitor ID:3  
TO SET/RESET REMOTE CONTROL MODE  
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for  
2 seconds.  
Remote does  
not work  
Remote does  
not work  
Remote works  
Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold  
down for 2 seconds.  
In order for this feature to work properly, the display must be assigned a Monitor ID number.  
The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD  
(See page 23).  
Figure 2  
Remote set up  
to use REMOTE  
ID:3  
Point the remote control towards the remote sensor of the desired monitor and press the  
REMOTE ID SET button. The MONITOR ID number is shown on the display when your  
remote control is in ID mode.  
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.  
1. Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100.  
This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.  
2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number  
(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to simultaneously  
control all displays in range.  
3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.  
The MONITOR ID number is shown in red on the display.  
If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.  
If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.  
NOTE: GROUP ID cannot be specified via the remote control.  
English-30  
Multiple Monitors Connection  
You can control mutliple monitors by using RS-232C, REMOTE IN or LAN daisy-chain connection.  
NOTE:  
Multiple monitors that are daisy-chained have a limit to the connectable monitors.  
When manually specify the ID number or control by the specified ID number, please execute AUTO ID (see page 23)  
previously.  
Main Monitor  
Connector  
Sub Monitors  
Connector  
IN  
OUT  
IN  
OUT  
RS-232C  
REMOTE IN  
LAN1  
LAN2  
LAN1  
LAN2  
Connection  
MultiSync  
MultiSync  
LAN1 LAN2  
LAN1 LAN2  
LAN Cable  
LAN Cable  
MultiSync  
English-31  
Controlling the LCD monitor via RS-232C Remote Control  
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.  
Functions that can be controlled by a personal computer are:  
Power ON or OFF.  
Switching between input signals.  
Sound Mute ON or OFF.  
Connection  
LCD Monitor + PC  
MultiSync  
PC  
RS-232C  
RS-232C Cable  
NOTE:  
If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your  
dealer for details.  
For the pin assignment, please see page 49 “2) RS-232C input/output”.  
To control a monitor, please use the control command. Instructions for the control command can be found on the CD included  
with the display. The file is called “External_control.pdf”.  
1) Interface  
PROTOCOL  
BAUD RATE  
DATA LENGTH  
PARITY BIT  
STOP BIT  
RS-232C  
9600 [bps]  
8 [bits]  
NONE  
1 [bit]  
FLOW CONTROL NONE  
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.  
The reverse type cable (null modem cable) (not include) should be used for RS-232C control.  
English-32  
2) Control command diagram  
For other commands, please see “External_Control.pdf” file on the CD-ROM.  
Function (Monitor ID = 1)  
Code Data  
Power ON  
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d  
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 46 03 04 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 33 03 71 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 31 03 73 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 43 03 01 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 35 03 77 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 37 03 75 0d  
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 44 03 06 0d  
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 0d  
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a 0d  
Power OFF  
Input Source Select DisplayPort  
Input Source Select DVI  
Input Source Select VGA  
Input Source Select HDMI  
Input Source Select Y/Pb/Pr  
Input Source Select VIDEO  
Input Source Select S-VIDEO  
Input Source Select OPTION  
Sound Mute ON  
Sound Mute OFF  
English-33  
Controlling the LCD monitor via LAN Control  
Connecting to a Network  
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.  
To use a LAN connection, you are required to assign an IP address.  
Example of LAN connection:  
Server  
NOTE: Use a category 5 or higher LAN cable.  
Hub  
LAN cable  
(not supplied)  
Network Setting by Using an HTTP Browser  
Overview  
Connecting the monitor to a network allows for monitor control from a computer via the network.  
To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.  
The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP  
server function. Please be sure to use “Microsoft Internet Explorer 7.0” or a higher version for the web browser.  
(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will  
vary depending on the version of browser. Please refer to the help files and the other information provided in your software.)  
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the  
monitor and entering the following URL.  
Network Setting  
TIP:  
The default IP address is assigned automatically to the monitor.  
The exclusive application can be downloaded from our website.  
NOTE:  
If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to  
refresh your web browser (or clear the cache).  
The display or button’s response can be slowed down or operation may not be accepted depending the settings of  
your network. Should this happen, consult your network administrator.  
The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a  
moment and repeat. If you still can’t get a response, turn the monitor off and then back on.  
To control a monitor please use the control command. See “Control command diagram” ( page 33).  
English-34  
Preparation Before Use  
Connect the monitor to a commercially available LAN cable before engaging in browser operations.  
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting  
method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be  
displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation.  
It is recommended that a proxy server not be used unless it is unavailable.  
Handling of the Address for Operation via a Browser  
The host name can be used under the following cases:  
If the host name corresponding to the IP address of the monitor has been registered to the domain name server (DNS) by the  
network administrator, you can then access the network settings of the display via that registered host name using a compatible  
browser.  
If the host name corresponding to the IP address of the monitor has been configured in the “HOSTS” file of the computer being  
used, you can then access the network settings of the display via that host name using a compatible browser.  
Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by  
specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL.  
Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying  
http://192.168.73.1/index.html for the address or the entry column of the URL.  
Operation  
Access the following address to show HOME. Click each link on the left side of HOME.  
REMOTE CONTROL  
Enable to control equivalent as the remote control key.  
OSD menu  
Enable to set the following OSD menu.  
PICTURE, ADJUST, AUDIO, SCHEDULE, PIP, OSD, MULTI DISPLAY, DISPLAY PROTECTION, EXTERNAL CONTROL,  
ADVANCED OPTION1, ADVANCED OPTION2.  
NOTE:  
Function of buttons which are shown on setting pages.  
[APPLY]: Reflect your settings.  
[CANCEL]: Return to the previous settings. NOTE: CANCEL is disabled after clicking APPLY.  
[RELOAD]: Reload the settings.  
[RESET]: Resets to the initial setting.  
English-35  
Network Setting  
Click “NETWORK” on the left side of HOME.  
IP SETTING  
Set for IP ADDRESS setting.  
AUTO: Automatically assign an IP address.  
MANUAL: Set your IP address of the network connected to the monitor.  
NOTE: Consult your network administrator for the IP address when [AUTO] is selected for  
[IP SETTING].  
IP ADDRESS  
Set your IP address of the network connected to the monitor when [MANUAL] is selected for  
[IP SETTING].  
SUBNET MASK  
Set your subnet mask number of the network connected to the monitor when [MANUAL] is selected  
for [IP SETTING].  
DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when [MANUAL] is selected for  
[IP SETTING].  
NOTE: Set as [0.0.0.0] to delete the setting.  
DNS  
Set for IP ADDRESS setting of DNS server.  
AUTO: Automatically assign an IP address of DNS server connected to the monitor.  
MANUAL: Set your IP address of DNS server connected to the monitor.  
PRIMARY DNS  
Set your primary DNS settings of the network connected to the monitor.  
NOTE: Set as [0.0.0.0] to delete the setting.  
SECONDARY DNS  
Set your secondary DNS settings of the network connected to the monitor.  
NOTE: Set as [0.0.0.0] to delete the setting.  
NOTE:  
The following settings will reset back to the factory setting when “IP ADDRESS RESET” is selected by an EXTERNAL  
CONTROL of OSD:  
[IP SETTING]: AUTO, [IP ADDRESS]: 192.168.0.10, [SUBNET MASK]: 255.255.255.0, [DNS]: AUTO [DEFAULT  
GATEWAY], [PRIMARY DNS] and [SECONDARY DNS] are blank.  
English-36  
Mail Setting  
Click “MAIL” on the left side of HOME.  
This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be  
sent when an error occurs in the monitor.  
ALERT MAIL  
Checking [ENABLE] will turn on the Alert Mail feature.  
Checking [DISABLE] will turn off the Alert Mail feature.  
STATUS MESSAGE  
HOST NAME  
Checking [ENABLE] will turn on the STATUS MESSAGE feature.  
Checking [DISABLE] will turn off the STATUS MESSAGE feature.  
Type in the hostname of the network connected to the monitor.  
Up to 15 alphanumeric characters can be used.  
DOMAIN NAME  
Type in the domain name of the network connected to the monitor.  
Up to 60 alphanumeric characters can be used.  
SENDER’S ADDRESS  
SMTP SERVER  
Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.  
Type in the SMTP server name to be connected to the monitor.  
Up to 60 alphanumeric characters can be used.  
RECIPIENT’S  
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.  
ADDRESS 1 TO 3  
AUTHENTICATION  
METHOD  
This selects the authentication method of the e-mail transmission.  
POP3 SERVER  
USER NAME  
This specifies the address of the POP3 server that is used in the authentication of the e-mail.  
This sets the user name for logging into the authentication server when authentication is required  
for the e-mail transmission. Up to 60 alphanumeric characters can be used.  
TEST MAIL  
Click this button to send a test mail to check if your settings are correct.  
NOTE:  
TIP:  
• If you execute a test, you may not receive an Alert mail.  
Should this happen, check if the network settings are correct.  
• If you entered an incorrect address in a test, you may not receive an Alert mail.  
Should this happen, check if the Recipient’s Address is correct.  
The Alert Mail settings will not be affected even when [RESET] is done from the menu.  
For Control command diagram, please see file “External_Control.pdf” on the CD-ROM.  
English-37  
Alert error message list  
Error number  
* ErrorCode  
Alert mail Message  
Explanation  
Measure  
The monitor’s power supply is not  
functioning normally.  
Standby power Abnormal  
Please contact your supplier.  
70h ~ 7Fh  
80h ~ Fh  
The cooling fan has stopped.  
Cooling fan Abnormal  
Backlight abnormal  
Please contact your supplier.  
Please contact your supplier.  
The monitor’s back light unit is not  
functioning normally.  
90h ~ 9Fh  
A0h ~ AFh  
The monitor is overheated.  
Temperature Abnormal  
Please contact your supplier.  
SENSOR reached at the temperature  
that the user had specified.  
Reconfirm the setting condition from  
OSD (DISPLAY PROTECTION-FAN  
CONTROL) or please contact your  
supplier.  
A2h  
*condition: DISPLAY PROTECTION-FAN  
CONTROL-COOLING FAN = AUTO  
The monitor doesn’t have the input  
signal.  
No signal  
Please check “No picture” in  
“Troubleshooting”.  
B0h ~ BFh  
D0h  
The remaining capacity of the error log Proof of Play log memory size is 1 more  
decreased.  
Please get a log by using PD external  
command. See page 43.  
hour.  
The system error occurred in the  
monitor.  
System error.  
Please contact your supplier.  
E0h ~ EFh  
Sample: The following examples are content of Alert Mail that informs the temperature anomaly of monitor.  
Sample: The following examples are content of test mail by browser.  
English-38  
SNMP Setting  
Click “SNMP” on the left side of HOME.  
This function allows for getting status and controlling of a monitor via the network.  
Version:  
SNMP v1 Authenticated plaintext by community name, not return a confirmation message of Trap.  
SNMP v2c Authenticated plaintext by community name, return a confirmation message of Trap.  
Community name:  
The default setting of community name is “public”. It is read only. You can set community names for up to 3 settings.  
Trap:  
Sending error message to specified address when an error occurs in the monitor.  
Check Box  
Temperature  
Explanation  
Temperature abnormal  
Cooling fan abnormal  
Power abnormal  
Error code  
0xA0, 0xA1, 0xA2  
Fan  
0x80, 0x81  
Power  
0x70, 0x71, 0x72, 0x78  
Inverter/Backlight  
No Signal  
Inverter or backlight abnormal 0x90, 0x91  
No signal  
0xB0  
0xD0  
0xE0  
PROOF OF PLAY  
System Error  
Lower the log storage  
System error  
English-39  
AMX Setting  
Click “AMX” on the left side of HOME.  
AMX BEACON  
Turn on or off for detection from AMX Device Discovery when connecting to the network supported by  
AMX’s NetLinx control system.  
TIP:  
When using a device that supports AMX Device Discovery, all AMX NetLinx control system will  
recognize the device and download the appropriate Device Discovery Module from an AMX server.  
Placing a checkmark will enable detecting the projector from AMX Device Discovery.  
Clearing a checkmark will disable detecting the projector from AMX Device Discovery.  
CRESTRON Setting  
Click “CRESTRON” on the left side of HOME.  
CRESTRON ROOMVIEW compatibility  
The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and  
controlled from a computer or a controller.  
ROOMVIEW  
ROOMVIEW for managing from the computer.  
ON: Enables ROOMVIEW.  
OFF: Disables ROOMVIEW.  
CRESTRON  
CONTROL  
CRESTRON CONTROL for managing from the controller.  
ON: Enables CRESTRON CONTROL.  
OFF: Disables CRESTRON CONTROL.  
CONTROLLER IP  
ADDRESS  
Set your IP address of CRESTRON SERVER.  
IP ID  
Set your IP ID of CRESTRON SERVER.  
TIP: The CRESTRON settings are required only for use with CRESTRON ROOMVIEW.  
For more information, visit http://www.crestron.com  
English-40  
Name Setting  
Click “NAME” on the left side of HOME.  
Set a monitor name. The name must be 16 characters or less. The default is model name.  
Network Password Setting  
Click “NETWORK PASSWORD” on the left side of HOME.  
PJLink PASSWORD Set a password for PJLink*. A password must be 32 characters or less. Do not forget your password.  
However, if you forget your password, consult with your dealer.  
HTTP PASSWORD  
Set a password for HTTP server. A password must be 10 characters or less.  
HTTP PASSWORD  
ENABLE  
HTTP PASSWORD is required when logging in HTTP server.  
Set a monitor name as USER NAME when inputting the password.  
*What is PJLink?  
PJLink is a standardization of protocol used for controlling projectors of different manufacturers. This standard protocol is  
established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.  
The projector supports all the commands of PJLink Class 1.  
Setting of PJLink will not be affected even when [RESET] is done from the menu.  
English-41  
PD List Information  
Click “PD LIST” on the left side of HOME.  
Show the list of ID and IP address of multiple monitors that are daisy-chained.  
Only the master monitor can show the list.  
Memo Setting  
Click “MEMO” on the left side of HOME.  
Set a title and meesage.  
TITLE  
A title must be 24 characters or less.  
MESSAGE  
A message must be 240 characters or less.  
MEMO PASSWORD The default is “0000”.  
MEMO PASSWORD MEMO PASSWORD is required when setting MEMO.  
ENABLE  
English-42  
POINT ZOOM  
Using “SET/POINT ZOOM” button on a remote control allows to enlarge a partial of image.  
Press CH+/- button to zoom up or down. The image can be expanded from 1 to 10 times.  
1
2
3
4
5
6
Press [SET/POINT ZOOM] button on a remote control. An icon will be a magnifier.  
Move magnifier icon by [ ] [ ] [+] [-] button.  
Press [CH+] to zoom up. Press [CH-] to zoom down.  
Press [SET/POINT ZOOM] to disappear the icon.  
Press [EXIT] to return to a normal size.  
Press [MENU] to display OSD menu.<Setting Procedure>  
NOTE:  
• The image may be distorted during this function.  
• This function does not work when set to PIP, POP, PBP, TILE MATRIX, SCREEN SAVER, SUPER in INPUT  
CHANGE, IMAGE FLIP.  
• When selected DYNAMIC or ZOOM in ASPECT, the image will be changed FULL, then start to POINT ZOOM.  
After POINT ZOOM, the ASPECT will be returned previous ASPECT settings. When the ASPECT is changed  
during POINT ZOOM, DYNAMIC and ZOOM will be FULL image.  
• The magnifier icon does not move to no image area.  
• POINT ZOOM will be released after changing input signal or power off.  
• POINT ZOOM will be released when setting IMAGE FLIP or changing ASPECT setting during POINT ZOOM.  
PROOF OF PLAY  
This function allows to send message for the current status of monitor by self checking.  
Check item  
INPUT  
Message  
DVI, VGA, Y/Pb/Pr, HDMI, DPORT, HDMI2*, DPORT2*, DPORT3*, RGB/HV*, Y/Pb/Pr2*, SCART*,  
VIDEO*, S-VIDEO*, OPTION*  
Resolution  
ex. (H)1920, (V)1080 , (H)1360, (V)768 or No signal or Invalid signal  
IN1, IN2, IN3*, HDMI, DPORT, HDMI2*, DPORT2*, DPORT3*, OPTION (analog)*,  
OPTION (digital)*  
Audio INPUT  
Audio signal  
Picture Image  
Audio out  
Audio in or No Audio in or N/A (IN1, IN2, IN3*, OPTION (analog)*)  
Normal Picture or No Picture  
Normal Audio or No Audio  
Cumulative time  
(hour)/(minutes)/(second)  
*: This function depends on which option board you use.  
Sample:  
HDMI  
1920 x 1080  
HDMI  
Audio in  
Normal Picture  
Normal Audio  
0h/0m/0s  
NOTE:  
For Proof of Play function, please see “External_Control.pdf” on the CD-ROM.  
English-43  
INTELLIGENT WIRELESS DATA  
This function allows to get the data of monitor’s status by wireless communication even while the monitor is off.  
Some menu of OSD, you can set by this function.  
NOTE:  
Sensor position: The upper left of the front side (when seen from the front). See page 8.  
Please contact your supplier for detailed information.  
Function name  
Item Name  
Read/Write  
R/W  
PICTURE  
ADJUST  
AUDIO  
SCHEDULE  
PIP  
R/W  
R/W  
R/W  
R/W  
Setting read and write  
function  
OSD  
R/W  
MULTI DISPLAY  
DISPLAY PROTECTION  
EXTERNAL CONTROL  
ADVANCED OPTION1  
ADVANCED OPTION2  
Version display ENABLE  
MODEL NAME  
R/W  
R/W  
R/W  
R/W  
R/W  
Read only  
Read only  
Read only  
Read only  
Read only  
Read only  
Read only  
Read only  
Read only  
SERIAL NO  
MANUFACTURE DATE  
FW1  
Display information  
All data service  
FW2  
MAC ADDRESS  
RUNNING TIME  
English-44  
Features  
Reduced Footprint: Provides the ideal solution for environments with superior image quality.  
Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a  
variety of standards.  
OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six  
axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides  
the monitor with a uniform color profile. This assures that the colors displayed on the monitor are exactly the same as on the  
color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen  
and customise the color accuracy of your monitor to a variety of standards.  
sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and  
other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and  
backward compatibility with other common color standards.  
OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use  
on-screen menus.  
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing  
the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically  
optimizing display performance.  
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a  
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and  
lowering the air conditioning costs of the workplace.  
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.  
VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third  
party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard  
in North America.  
DVI-D: The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between  
computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based  
digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital  
connectors such as DFP and P&D. The DVI interface of this display supports HDCP.  
TILE MATRIX,TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.  
ZOOM: Expands image size for horizontal and vertical direction.  
Self-diagnosis: If an internal error should occur, a failure state will be indicated.  
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over  
a Digital Visual Interface (DVI). If you are unable to view material via the DVI input, this does not necessarily mean the display is  
not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP  
and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).  
Option board slot: You can use an option board. Please contact your supplier for detailed information.  
English-45  
Troubleshooting  
RED LED on monitor is blinking  
No picture  
A certain failure might have occurred, please contact your  
nearest authorized NEC DISPLAY SOLUTIONS service  
facility.  
The signal cable should be completely connected to the  
display card/computer.  
The display card should be completely seated in its slot.  
If the monitor is powered off by the inside temperature  
being higher than the normal operating temperature, a RED  
LED will blink six times. Power on the display again after  
confirming the inside temperature has been reduced to  
normal operation temperature.  
Check the main Power Switch, it should be in the ON  
position.  
Front Power Switch and computer power switch should be in  
the ON position.  
Check to make sure that a supported mode has been  
selected on the display card or system being used. (Please  
consult display card or system manual to change graphics  
mode.)  
Display image is not sized properly  
Use the OSD Image Adjust controls to increase or decrease  
the coarse adjustment.  
Check to make sure that a supported mode has been  
selected on the display card or system being used.  
(Please consult display card or system manual to change  
graphics mode.)  
Check the monitor and your display card with respect to  
compatibility and recommended settings.  
Check the signal cable connector for bent or pushed-in pins.  
The monitor automatically goes into OFF at the preset time  
period after signal is lost. Press the power button.  
Selected resolution is not displayed properly  
Use OSD Display Mode to enter Information menu and  
confirm that the appropriate resolution has been selected. If  
not, select corresponding option.  
Power Button does not respond  
Unplug the power cord of the monitor from the AC outlet to  
turn off and reset the monitor.  
No Sound  
Check the main Power Switch on the back side of the monitor.  
Check to see if audio cable is properly connected.  
Image persistence  
Check to see if mute is activated.  
Please be aware that LCD Technology may experience  
a phenomenon known as Image Persistence. Image  
Persistence occurs when a residual or “ghost” image of a  
previous image remains visible on the screen. Unlike CRT  
monitors, LCD monitors’ image persistence is not permanent,  
but constant images being displayed for a long period of time  
should be avoided. To alleviate image persistence, turn off  
the monitor for as long as the previous image was displayed.  
For example, if an image was on the monitor for one hour  
and a residual image remains, the monitor should be turned  
off for one hour to erase the image.  
Check to see if volume is set at minimum.  
Check to see if computer supports an audio signal through  
DisplayPort.  
If unsure, contact the computer manufacturer.  
Check to see if SURROUND is ON.  
Check Internal/External speaker switch.  
Remote Control is not available  
Check the Remote Control’s batteries status.  
Check if batteries are inserted correctly.  
Check if the Remote Control is pointing at the monitor’s  
remote sensor.  
NOTE:  
As with all personal display devices, NEC DISPLAY  
SOLUTIONS recommends displaying moving images  
and using a moving screen saver at regular intervals  
whenever the screen is idle or turning off the monitor  
when not in use.  
Check the IR LOCK SETTING status.  
The remote control system may not function when direct  
sunlight or strong illumination strikes the remote control  
sensor of the LCD monitor, or when there is an object in the  
path.  
Image is unstable, unfocused or swimming is apparent  
Signal cable should be completely attached to the computer.  
“SCHEDULE”/“OFF TIMER” function is not working properly  
Use the OSD Image Adjust controls to focus and adjust  
display by increasing or decreasing the fine adjustment.  
When the display mode is changed, the OSD Image Adjust  
settings may need to be re-adjusted.  
The “SCHEDULE” function will be disabled when the “OFF  
TIMER” is set.  
If the “OFF TIMER” function is enabled and the power to  
the LCD monitor is turned off when the power supply is  
interrupted unexpectedly, then the “OFF TIMER” will be reset.  
Check the monitor and your display card with respect to  
compatibility and recommended signal timings.  
If your text is garbled, change the video mode to non-  
interlace and use 60Hz refresh rate.  
Snowy Picture, Poor Sound in TV  
Check antenna/cable connection. Use new cable if  
necessary.  
Image of component signal is greenish  
Check to see if the Y/Pb/Pr input connector is selected.  
Interference in TV  
Check components for shielding, move away from monitor if  
necessary.  
LED on monitor is not lit  
(no green or red color can be seen)  
Power Switch should be in the ON position and power cord  
should be connected.  
RS-232C or LAN control is not available  
Check RS-232C or LAN cable connection.  
Check the main Power Switch, it should be in the ON  
position.  
Make certain the computer is not in a power-saving mode  
(touch the keyboard or mouse).  
Check to see that the power indicator option in the OSD is  
set to ON.  
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or degradation.  
English-46  
Specifications - P403  
Product Specifications  
LCD Module  
40”/1016 mm diagonal  
Pixel Pitch: 0.461 mm  
Resolution: 1920 x 1080  
Color: Over 16 million colors (depending on video card used)  
Brightness: 700 cd/m2 (Max.), 550 cd/m2 (Factory setting Typ.) @25°C  
Contrast Ratio: 4000:1  
Viewing Angle: 89° (typ) @ CR>10  
Frequency  
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)  
31.5 kHz - 91.1 kHz (Digital Input)  
Vertical: 50.0 - 85.0 Hz  
Pixel Clock  
Viewable Size  
Input Signal  
DVI  
25.2 MHz - 162.0 MHz  
885.6 x 498.2 mm  
DVI-D 24pin  
Digital RGB  
DVI (HDCP)  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i  
DisplayPort DisplayPort Connector Digital RGB  
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),  
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4  
VGA*2  
HDMI  
15pin Mini D-sub  
Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)  
Separate: TTL level (Pos./Neg.)  
Composite sync on Green Video: 0.3 Vp-p Neg.  
HDMI Connector  
15pin Mini D-sub  
Digital YUV  
Digital RGB  
HDMI  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),  
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,  
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4  
Y/Pb/Pr*2  
Component  
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm  
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz  
Output Signal  
DisplayPort DisplayPort Connector Digital RGB  
AUDIO  
AUDIO  
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3  
Stereo L/R 0.5 Vrms  
STEREO Mini Jack  
Analog Audio  
Input  
HDMI Connector  
Digital Audio  
PCM 32, 44.1, 48 KHz (16/20/24bit)  
PCM 32, 44.1, 48 KHz (16/20/24bit)  
Stereo L/R 0.5 Vrms  
DisplayPort Connector Digital Audio  
STEREO Mini Jack Analog Audio  
AUDIO  
Output  
Speaker Output  
External Speaker Jack 15 W + 15 W (8 ohm)  
Internal Speaker 10 W + 10 W (Stereo)  
Control  
RS-232C In: 9 Pin D-sub  
LAN: RJ-45 10/100 BASE-T  
Remote IN: Stereo Mini jack 3.5  
Service port  
USB service port for maintenance  
Power Supply  
2.9 - 1.2 A @ 100-240V AC, 50/60Hz  
Operational Environment  
Temperature*3: 0 - 40°C / 32 - 104°F, 0 - 35°C / 32 - 95°F (Face up position/Face down position/with Slot 2  
type PC)  
Humidity: 20 - 80% (without condensation)  
Altitude: 0 - 3000 m (Brightness may decrease with altitude)  
Storage Environment  
Dimension  
Temperature: -20 - 60°C / -4 - 140°F  
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C  
920.6 (W) x 532.2 (H) x 69.3 (D) mm / 36.2 (W) x 21.0 (H) x 2.7 (D) inches (with handle)  
920.6 (W) x 532.2 (H) x 66.5 (D) mm / 36.2 (W) x 21.0 (H) x 2.6 (D) inches (without handle)  
Weight  
17.0 kg (37.5 lbs)  
VESA compatible mounting interface  
Power Management  
Plug & Play  
300 mm x 300 mm (M6, 4 Holes)  
VESA DPM  
VESA DDC2B, DDC/CI, DisplayPort  
16V/3.6 A  
Power supply for Slot 2 type OPTION  
Accessories  
Setup manual, Power Cord, Video Signal cable, Remote Control, AAA Battery x 2, Clamp x 1,  
Screw x 1, CD-ROM  
NOTE: Technical specifications are subject to change without notice.  
*1: Compressed image.  
*2: Common terminal.  
*3: When you use option board accessories, please contact your supplier for detailed information.  
*4: Displayed text may be blurred.  
English-47  
Specifications - P463  
Product Specifications  
LCD Module  
46”/1168 mm diagonal  
Pixel Pitch: 0.530 mm  
Resolution: 1920 x 1080  
Color: Over 16 million colors (depending on video card used)  
Brightness: 700 cd/m2 (Max.), 550 cd/m2 (Factory setting Typ.) @25°C  
Contrast Ratio: 4000:1  
Viewing Angle: 89° (typ) @ CR>10  
Frequency  
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)  
31.5 kHz - 91.1 kHz (Digital Input)  
Vertical: 50.0 - 85.0 Hz  
Pixel Clock  
Viewable Size  
Input Signal  
DVI  
25.2 MHz - 162.0 MHz  
1018.1 x 572.7 mm  
DVI-D 24pin  
Digital RGB  
DVI (HDCP)  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i  
DisplayPort DisplayPort Connector Digital RGB  
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),  
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4  
VGA*2  
HDMI  
15pin Mini D-sub  
Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)  
Separate: TTL level (Pos./Neg.)  
Composite sync on Green Video: 0.3 Vp-p Neg.  
HDMI Connector  
15pin Mini D-sub  
Digital YUV  
Digital RGB  
HDMI  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),  
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,  
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4  
Y/Pb/Pr*2  
Component  
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm  
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz  
Output Signal  
DisplayPort DisplayPort Connector Digital RGB  
AUDIO  
AUDIO  
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3  
Stereo L/R 0.5 Vrms  
STEREO Mini Jack  
Analog Audio  
Input  
HDMI Connector  
Digital Audio  
PCM 32, 44.1, 48 KHz (16/20/24bit)  
PCM 32, 44.1, 48 KHz (16/20/24bit)  
Stereo L/R 0.5 Vrms  
DisplayPort Connector Digital Audio  
STEREO Mini Jack Analog Audio  
AUDIO  
Output  
Speaker Output  
External Speaker Jack 15 W + 15 W (8 ohm)  
Internal Speaker 10 W + 10 W (Stereo)  
Control  
RS-232C In: 9 Pin D-sub  
LAN: RJ-45 10/100 BASE-T  
Remote IN: Stereo Mini jack 3.5  
Service port  
USB service port for maintenance  
Power Supply  
3.2 - 1.3 A @ 100-240V AC, 50/60Hz  
Operational Environment  
Temperature*3: 0 - 40°C / 32 - 104°F, 0 - 35°C / 32 - 95°F (Face up position/Face down position/with Slot 2  
type PC)  
Humidity: 20 - 80% (without condensation)  
Altitude: 0 - 3000 m (Brightness may decrease with altitude)  
Storage Environment  
Dimension  
Temperature: -20 - 60°C / -4 - 140°F  
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C  
1055.4 (W) x 608.6 (H) x 69.3 (D) mm / 41.6 (W) x 24.0 (H) x 2.7 (D) inches (with handle)  
1055.4 (W) x 608.6 (H) x 64.5 (D) mm / 41.6 (W) x 24.0 (H) x 2.5 (D) inches (without handle)  
Weight  
21.4 kg (47.2 lbs)  
VESA compatible mounting interface  
Power Management  
Plug & Play  
300 mm x 300 mm (M6, 4 Holes)  
VESA DPM  
VESA DDC2B, DDC/CI, DisplayPort  
16V/3.6 A  
Power supply for Slot 2 type OPTION  
Accessories  
Setup manual, Power Cord, Video Signal cable, Remote Control, AAA Battery x 2, Clamp x 1,  
Screw x 1, CD-ROM  
NOTE: Technical specifications are subject to change without notice.  
*1: Compressed image.  
*2: Common terminal.  
*3: When you use option board accessories, please contact your supplier for detailed information.  
*4: Displayed text may be blurred.  
English-48  
Specifications - P553  
Product Specifications  
LCD Module  
55”/1388 mm diagonal  
Pixel Pitch: 0.630 mm  
Resolution: 1920 x 1080  
Color: Over 16 million colors (depending on video card used)  
Brightness: 700 cd/m2 (Max.), 550 cd/m2 (Factory setting Typ.) @25°C  
Contrast Ratio: 4000:1  
Viewing Angle: 89° (typ) @ CR>10  
Frequency  
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)  
31.5 kHz - 91.1 kHz (Digital Input)  
Vertical: 50.0 - 85.0 Hz  
Pixel Clock  
Viewable Size  
Input Signal  
DVI  
25.2 MHz - 162.0 MHz  
1209.6 x 680.4 mm  
DVI-D 24pin  
Digital RGB  
DVI (HDCP)  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i  
DisplayPort DisplayPort Connector Digital RGB  
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),  
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4  
VGA*2  
HDMI  
15pin Mini D-sub  
Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)  
Separate: TTL level (Pos./Neg.)  
Composite sync on Green Video: 0.3 Vp-p Neg.  
HDMI Connector  
15pin Mini D-sub  
Digital YUV  
Digital RGB  
HDMI  
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),  
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,  
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4  
Y/Pb/Pr*2  
Component  
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm  
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz  
Output Signal  
DisplayPort DisplayPort Connector Digital RGB  
AUDIO  
AUDIO  
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3  
Stereo L/R 0.5 Vrms  
STEREO Mini Jack  
Analog Audio  
Input  
HDMI Connector  
Digital Audio  
PCM 32, 44.1, 48 KHz (16/20/24bit)  
PCM 32, 44.1, 48 KHz (16/20/24bit)  
Stereo L/R 0.5 Vrms  
DisplayPort Connector Digital Audio  
STEREO Mini Jack Analog Audio  
AUDIO  
Output  
Speaker Output  
External Speaker Jack 15 W + 15 W (8 ohm)  
Internal Speaker 10 W + 10 W (Stereo)  
Control  
RS-232C In: 9 Pin D-sub  
LAN: RJ-45 10/100 BASE-T  
Remote IN: Stereo Mini jack 3.5  
Service port  
USB service port for maintenance  
Power Supply  
3.6 - 1.5 A @ 100-240V AC, 50/60Hz  
Operational Environment  
Temperature*3: 0 - 40°C / 32 - 104°F, 0 - 35°C / 32 - 95°F (Face up position/Face down position/with Slot 2  
type PC)  
Humidity: 20 - 80% (without condensation)  
Altitude: 0 - 3000 m (Brightness may decrease with altitude)  
Storage Environment  
Dimension  
Temperature: -20 - 60°C / -4 - 140°F  
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C  
1250.2 (W) x 721.0 (H) x 69.3 (D) mm / 49.2 (W) x 28.4 (H) x 2.7 (D) inches (with handle)  
1250.2 (W) x 721.0 (H) x 64.5 (D) mm / 49.2 (W) x 28.4 (H) x 2.5 (D) inches (without handle)  
Weight  
25.3 kg (55.8 lbs)  
VESA compatible mounting interface  
Power Management  
Plug & Play  
300 mm x 300 mm (M6, 4 Holes)  
VESA DPM  
VESA DDC2B, DDC/CI, DisplayPort  
16V/3.6 A  
Power supply for Slot 2 type OPTION  
Accessories  
Setup manual, Power Cord, Video Signal cable, Remote Control, AAA Battery x 2, Clamp x 3,  
Screw x 3, CD-ROM, Thumbscrew for optional stand x 2  
NOTE: Technical specifications are subject to change without notice.  
*1: Compressed image.  
*2: Common terminal.  
*3: When you use option board accessories, please contact your supplier for detailed information.  
*4: Displayed text may be blurred.  
English-49  
Pin Assignment  
1) Analog multi input (MiniDsub15p): VGA, Y/Pb/Pr  
Pin No Name  
1
2
Red, Y/Pb/Pr_Pr  
Green, Y/Pb/Pr_Y  
Blue, Y/Pb/Pr_Pb  
GND  
3
4
Mini D-SUB 15P (Monitor side)  
5
DDC-GND  
Red-GND  
Green-GND  
Blue-GND  
+5V (DDC)  
GND  
1
5
6
6
7
10  
15  
11  
8
9
10  
11  
12  
13  
14  
15  
NC  
DDC-SDA  
H-SYNC  
V-SYNC  
DDC-SCL  
2) RS-232C input/output  
Pin No Name  
1
2
3
4
5
6
7
8
9
NC  
D-SUB 9P (Monitor side)  
RXD  
TXD  
NC  
5
1
GND  
NC  
6
9
NC  
NC  
NC  
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.  
3) REMOTE IN  
English-50  
Manufacturer’s Recycling and Energy Information  
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top  
priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly  
products, and always strive to help define and comply with the latest independent standards from agencies such as ISO  
(International Organisation for Standardization) and TCO (Swedish Trades Union).  
Disposing of your old NEC product  
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of  
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely  
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures  
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.  
All required information concerning the disposal of the product and country-specific information on recycling facilities can be  
found on our following websites:  
Energy Saving  
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)  
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.  
Mode  
Power consumption  
LED colour  
Approx. 105 W (P403)  
Approx. 115 W (P463)  
Approx. 150 W (P553)  
Normal Operation*1  
Green  
Energy Saving Mode*1  
Power Off  
Less than 2.5 W  
Less than 0.5 W  
Amber  
Red  
*1: without any option, with factory settings.  
WEEE Mark (European Directive 2012/19/EU)  
Within the European Union  
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic  
products carrying the mark (left) must be disposed of separately from normal household waste. This includes  
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your  
NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased  
the product, or if applicable, follow any agreements made between yourself and NEC.  
The mark on electrical and electronic products only applies to the current European Union Member States.  
Outside the European Union  
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority  
so as to comply with the correct disposal method.  
English-51  

Xerox All In One Printer M128 User Manual
Vector Iveco Motos V08 Ent M11 User Manual
Trane Air Conditioner 4ttx6048 User Manual
Toshiba Air Conditioner Mmy Map1204ht8z E User Manual
Schumacher 6000a User Manual
NEC MULTISYNC C551 User Manual
JORJIN WA6800 00 User Manual
GE ASP12 User Manual
FUJITSU SCANSNAP S1100 User Manual
D LINK DAP 2230 User Manual