NEC MULTISYNC E203WI User Manual

Desktop Monitor  
MultiSync E203Wi  
MultiSync E233WM  
User’s Manual  
Please find your model name in the label on the backside of monitor.  
WARNING  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT  
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE  
PRONGS CAN BE FULLY INSERTED.  
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
CAUTION  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED  
FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT  
THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER  
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause  
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.  
This symbol alerts the user that important literature concerning the operation and maintenance of this unit  
has been included. Therefore, it should be read carefully in order to avoid any problems.  
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not  
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the  
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.  
Plug Type  
North America  
European Continental  
U.K.  
Chinese  
Japanese  
Plug Shape  
Country  
Voltage  
U.S.A./Canada  
120*  
EU (except U.K.)  
230  
U.K.  
230  
China  
220  
Japan  
100  
*When operating the monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply  
voltage of the AC power outlet being used.  
NOTE:  
This product can only be serviced in the country where it was purchased.  
English-1  
Registration Information  
FCC Information  
1.  
Use the attached specified cables with the MultiSync E203Wi (L203QX)/MultiSync E233WM (L235QU) color monitor so  
as not to interfere with radio and television reception.  
(1)  
The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,  
and meet the following condition.  
Power supply cord  
Plug shape  
Non shield type, 3-conductor  
U.S.A  
(2)  
Please use the supplied shielded video signal cable.  
Use of other cables and adapters may cause interference with radio and television reception.  
2.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used  
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult your dealer or an experienced radio/TV technician for help.  
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.  
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify  
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,  
Washington, D.C., 20402, Stock No. 004-000-00345-4.  
English-2  
Declaration of Conformity  
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
U.S. Responsible Party: NEC Display Solutions of America, Inc.  
Address:  
500 Park Boulevard, Suite 1100  
Itasca, Illinois 60143  
(630) 467-3000  
Tel. No.:  
Type of Product:  
Display Monitor  
Equipment Classification: Class B Peripheral  
Model: MultiSync E203Wi (L203QX)  
MultiSync E233WM (L235QU)  
We hereby declare that the equipment specified above conforms  
to the technical standards as specified in the FCC Rules.  
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.  
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.  
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.  
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,  
Norway, Spain, Sweden, U.K.  
All other brands and product names are trademarks or registered trademarks of their respective owners.  
ENERGY STAR is a U.S. registered trademark.  
®
As an ENERGY STAR Partner, NEC Display Solutions of America, Inc. has determined that this product  
meets the ENERGY STAR guidelines for energy efficiency. The ENERGY STAR emblem does not represent EPA  
endorsement of any product or service.  
DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards  
Association in the United States and other countries.  
English-3  
Recommended use  
Safety Precautions and Maintenance  
FOR OPTIMUM PERFORMANCE, PLEASE NOTE  
THE FOLLOWING WHEN SETTING UP AND  
USING THE LCD COLOR MONITOR:  
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose  
you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.  
Do not spill any liquids into the cabinet or use your monitor near water.  
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or  
fatal or may cause electric shock, fire or equipment failure.  
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.  
Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to  
the monitor.  
The power supply cord you use must have been approved by and comply with the safety standards of your country.  
(Type H05VV-F 3G 0.75 mm2 should be used in Europe).  
In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.  
Do not place any objects onto the monitor and do not use the monitor outdoors.  
Do not bend power cord.  
Do not use monitor in high temperatured, humid, dusty, or oily areas.  
Do not cover vent on monitor.  
Vibration can damage the backlight. Do not install where the monitor will be exposed to continual vibration.  
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.  
To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks, make sure to install the  
monitor in a stable location and take measures to prevent falling.  
Immediately turn off the power, unplug your monitor from the wall outlet and move to a safe location then refer servicing to  
qualified service personnel under the following conditions. If the monitor is used in this condition, the monitor may cause fall, fire  
and electric shock:  
If the monitor stand has been cracked or peeled.  
If the monitor has been wobbled.  
If the monitor has an unusual odor.  
When the power supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen into the monitor.  
If the monitor has been exposed to rain or water.  
If the monitor has been dropped or the cabinet damaged.  
If the monitor does not operate normally by following operating instructions.  
Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated  
openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor.  
The power cable connector is the primary means of detaching the system from the power supply.  
The monitor should be installed close to a power outlet which is easily accessible.  
CAUTION  
Handle with care when transporting. Save packaging for transporting.  
Do not touch LCD panel surface while transporting, mounting and setting.  
Applying pressure on the LCD panel can cause serious damage.  
Image Persistence: Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen.  
Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period  
of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed.  
For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for  
one hour to erase the image.  
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular  
intervals whenever the screen is idle or turning off the monitor when not in use.  
English-4  
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN  
REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE  
FOLLOWING WHEN YOU POSITION THE MONITOR:  
For optimum performance, allow 20 minutes for the display to warm up.  
Adjust the monitor height so that the top of the screen is at or slightly below eye level.  
Your eyes should look slightly downward when viewing the middle of the screen.  
Position your monitor no closer than 40 cm (15.75 inches) and no further away than  
70 cm (27.56 inches) from your eyes. The optimal distance is 50 cm (19.69 inches).  
Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often.  
Position the monitor at a 90° angle to windows and other light sources to minimize glare  
and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen.  
If reflected light makes it hard for you to see your screen, use an anti-glare filter.  
Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any  
cleaning solution or glass cleaner!  
Adjust the monitor’s brightness and contrast controls to enhance readability.  
Use a document holder placed close to the screen.  
Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize  
turning your head while you are typing.  
Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).  
Get regular eye checkups.  
Ergonomics  
To realize the maximum ergonomics benefits, we recommend the following:  
To avoid eye fatigue, adjust the brightness to a moderate setting. Place a sheet of white paper next to the LCD screen for  
luminance reference.  
Do not position the Contrast control to its maximum setting.  
Use the preset Size and Position controls with standard signals.  
Use the preset Color Setting.  
Use non-interlaced signals with a vertical refresh rate between 60 Hz.  
Do not use primary color blue on a dark background, as it is difficult to see and may produce eye fatigue due to insufficient  
contrast.  
Cleaning the LCD Panel  
When the LCD is dusty, please gently wipe with a soft cloth.  
Please do not rub the LCD panel with coarse or hard material.  
Please do not apply pressure to the LCD surface.  
Please do not use OA cleaner as it will cause deterioration or discoloration to the LCD surface.  
Cleaning the Cabinet  
Unplug the power supply  
Gently wipe the cabinet with a soft cloth  
To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.  
NOTE:  
Many plastics are used on the surface of the cabinet. DO NOT clean with benzene, thinner, alkaline detergent,  
alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Do not touch rubber or  
vinyl to the cabinet for a long time. These types of fluids and fabrics can cause the paint to deteriorate, crack or peel.  
For more detailed information on setting up a healthy work environment, write to the American National Standard for Human Factors Engineering of Computer  
Workstations - ANSI/HFES 100-2007 - The Human Factors Society, Inc. P.O. Box 1369, Santa Monica, California 90406.  
English-5  
Contents  
Your new NEC LCD monitor box* should contain the following:  
LCD monitor with tilt base  
Power Cord*1  
Video Signal Cable (DVI-D to DVI-D cable)  
Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)  
Setup Manual  
Base Stand  
Audio cable*2  
Audio Cable*2  
Setup Manual  
Power Cord*1  
Video Signal Cable  
DVI-D to DVI-D  
cable  
Base Stand  
LCD monitor  
(Base Stand not connected)  
*
*
*
Remember to save your original box and packing material to transport or ship the monitor.  
Type of power cord included will depend on the where the LCD monitor is to be shipped.  
E233WM only.  
1
2
The model name is on the label.  
Rating label on the  
back of the display.  
Quick Start  
To attach the Base to the LCD stand:  
1. Place monitor face down on a non-abrasive surface (Figure 1).  
NOTE:  
2. Please pivot base 90 degrees as shown in Figure 1.  
NOTE: Handle with care when pulling the stand.  
3. Attach the base stand to LCD monitor and properly lock screw of base stand bottom (Figure 2).  
Handle with care when monitor facing down, for avoiding damage to the front control keys.  
NOTE:  
Reverse this procedure if you need to re-pack the monitor.  
Screw  
Figure 1  
Figure 2  
English-6  
To connect the LCD monitor to your system, follow these instructions:  
NOTE: Make sure to read “Recommended Use” (page 4) before installation.  
1. Turn off the power of your computer.  
2. For a PC with DisplayPort output: Connect the DisplayPort cable to the connector of the display card in your system  
(Figure A.1).  
For a PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system  
(Figure A.2). Tighten all screws.  
For a PC with Analog output: Connect a 15-pin mini D-SUB signal cable to the connector of the display card in your  
system (Figure A.3).  
For a MAC with Thunderbolt output: Connect a Mini DisplayPort to DisplayPort adapter (not included) to the computer,  
then attached the included DisplayPort cable to the adapter and to the display (Figure A.4).  
DisplayPort cable  
DVI cable  
Macintosh Cable Adapter (not included)  
Figure A.3  
Figure A.4  
Figure A.1  
Figure A.2  
NOTE:  
1. When removing the DisplayPort cable, hold down the top button to release the lock.  
2. Please use a DisplayPort Certified DisplayPort cable.  
20° Tilt  
3. Place hands on each side of the monitor to tilt the LCD panel 20-degree angle and lift up  
to the highest position.  
4. Connect all cables to the appropriate connectors (Figure C.1).  
NOTE:  
Incorrect cable connections may cause abnormal operation, damage display  
quality/components of LCD module and/or shorten the module’s life.  
Headphone*  
Use an audio cable without a built-in resistor. Using an audio cable with  
a built-in resistor turns down the sound*.  
Highest  
Stand  
Position  
CAUTION: To raise or lower screen, place a hand on each  
side of the monitor and lift or lower to the desired  
height. When you use handle to lower screen,  
you might pinch your fingers.  
Audio Input* D-SUB  
DisplayPort  
DVI  
Power cord  
Figure C.1  
* E233WM only.  
English-7  
5. To keep the cables neatly organized, place them into the cable management system that is built into the stand.  
Place the cables in the hooks firmly and evenly (Figure C.2 and Figure C.3).  
NOTE:  
Cable cover is not removable.  
6. Please check that you can still rotate, raise and lower the monitor screen after you have installed the cables.  
Power Cord  
Power Cord  
DVI Cable  
DVI Cable  
D-SUB Cable  
DisplayPort Cable*1  
Audio Cable*2  
D-SUB Cable  
DisplayPort Cable*1  
Audio Cable*2  
Figure C.2  
Figure C.3  
*1 Cable not included.  
*2 E233WM only.  
7. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet.  
NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.  
8. Turn on the computer and the monitor by touching the power key on the front bezel (Figure E.1).  
9. No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. For further adjustments, use  
the following OSD controls:  
• AUTO CONTRAST (Analog input only)  
• AUTO ADJUST (Analog input only)  
Refer to the Controls section of this User’s Manual for a full description of these OSD controls.  
NOTE:  
If you have any problems, please refer to the Troubleshooting section of this User’s Manual.  
Power Key  
Figure E.1  
English-8  
Raise and Lower Monitor Screen  
The monitor may be raised or lowered in either portrait or landscape mode.  
To raise or lower screen, place a hand on each side of the monitor and lift or lower to the desired height (Figure RL.1).  
NOTE:  
Handle with care when raising or lowering the monitor screen.  
Figure RL.1  
Screen Rotation  
Before rotating, disconnect power cord and all cables, then the screen must be raised to the highest level and tilt to avoid  
knocking the screen on the desk or pinching your fingers.  
To raise the screen, place a hand on each side of the monitor and lift up to the highest position (Figure RL.1).  
To rotate screen, place a hand on each side of the monitor screen and turn clockwise from landscape to portrait or counter-  
clockwise from portrait to landscape (Figure R.1).  
Figure R.1  
Tilt and Swivel  
Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).  
Figure TS.1  
NOTE:  
Handle with care when tilting the monitor screen.  
English-9  
Flexible Arm Installation  
This LCD monitor is designed for use with a flexible arm.  
To prepare the monitor for alternate mounting purposes:  
Follow the instructions provided by the manufacturer of the display mount.  
To meet the safety requirements, the mounting stand must be able to support the weight of the monitor and be UL-certified.  
* Contact your dealer for more information.  
Remove Monitor Stand for Mounting  
To prepare the monitor for alternate mounting purposes:  
1. Disconnect all cables.  
2. Place a hand on each side of the monitor and lift up to the highest position.  
3. Place monitor face down on a non-abrasive surface (Figure S.1).  
NOTE:  
4. Remove the 4 screws connecting the stand to the monitor (Figure S.1).  
NOTE: In order to avoid stand drop, when removing screws, please support stand with your hand.  
Handle with care when the monitor is facing down.  
5. Remove the stand (Figure S.2).  
6. The monitor is now ready for mounting in an alternate manner.  
7. Connect the cables to the back of the monitor.  
NOTE:  
Handle with care when removing monitor stand.  
Figure S.1  
Figure S.2  
8. Reverse this process to re-attach stand.  
NOTE:  
Use only VESA-compatible alternative mounting method.  
Handle with care when removing stand.  
NOTE:  
Match “TOP SIDE” mark on stand to top side of the monitor head when re-attaching stand.  
“TOP SIDE” mark  
Please match top side  
of the monitor  
English-10  
Mount Flexible Arm  
This LCD monitor is designed for use with a flexible arm.  
1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand.  
2. Use the 4 screws removed from the stand to attach the arm to the monitor (Figure F.1).  
Caution: Use ONLY the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand.  
To meet the safety requirements, the monitor must be mounted to an arm which guaranties the necessary  
stability under consideration of the weight of the monitor. The LCD monitor should only be used with an  
approved arm (e.g. TUEV GS mark).  
NOTE:  
Tighten all screws (recommended Fasten Force: 98 - 137N•cm).  
Thickness of Bracket (Arm)  
2.0~3.2 mm  
100 mm  
100 mm  
Weight of LCD assembly: 2.9 kg (E203Wi)  
3.7 kg (E233WM)  
Figure F.1  
Specifications  
4 Screws (M4)  
Spring washer  
Flat washer  
12 mm  
M4  
English-11  
Controls  
OSD (On-Screen Display) Control Functions  
1. Basic functions of the touch keys on the front of the monitor  
INPUT/RESET  
SELECT  
Displays OSD.  
+
OSD Menu  
Not displaying on screen Selects input signal.  
Shortcut to Brightness.  
Shortcut to Contrast  
(E203Wi).  
Shortcut to Volume  
(E233WM).  
Displaying on screen  
Icon Select  
Displays OSD menu and  
selects function icon.  
Moves leftward.  
Moves rightward.  
Adjusts up.  
Function Adjustment  
Reset the function.  
Adjusts the function of the Adjusts down.  
selected icon.  
2. OSD structure  
Example: E203Wi  
Main Menu (Icon Select)  
Main Menu (Adjust)  
Touch  
Touch  
“SELECT”  
key  
“SELECT”  
key again  
Touch “SELECT” key  
Adjust by using  
“–” or “+”  
Example: TOOL sub menu  
Touch “SELECT” key  
Touch  
“SELECT” key  
Touch “–” or  
“+” to select  
an icon  
Touch  
“–” or “+”  
Touch  
“SELECT” key  
Sub Menu (Icon Select)  
Select by using  
“–” or “+”  
Sub Menu (Adjust)  
English-12  
AUDIO (E233WM only)  
Controls the volume of the speakers or headphones.  
To mute the speaker output, select Audio icon and touch “INPUT/RESET” key.  
BRIGHTNESS  
Adjusts the overall image and background screen brightness.  
To enter the ECO MODE, touch the “INPUT/RESET” key.  
ECO MODE OFF: Sets brightness variable from 0% to 100%.  
ECO MODE1: Sets brightness 80%.  
This setting automatically adjusts brightness within a power consumption range that meets Energy Star  
measurement conditions.  
ECO MODE2: Sets brightness 40%.  
This setting can adjust brightness within the range that power has reduced 30% from maximum brightness setting.  
CONTRAST  
Adjusts the image brightness in relation to the background.  
To enter the DV MODE setting, touch the “INPUT/RESET” key.  
DV MODE: Setting that adjusts the brightness by detecting the screen’s black areas and optimizes it.  
AUTO CONTRAST (Analog input only)  
Adjusts the image displayed for non-standard video inputs.  
AUTO ADJUST (Analog input only)  
Automatically adjusts the Image Position, the H. Size and Fine settings.  
LEFT/RIGHT (Analog input only)  
Controls Horizontal Image Position within the display area of the LCD.  
DOWN/UP (Analog input only)  
Controls Vertical Image Position within the display area of the LCD.  
H. SIZE (Analog input only)  
Adjusts the horizontal size by increasing or decreasing this setting.  
FINE (Analog input only)  
Improves focus, clarity and image stability by increasing or decreasing this setting.  
COLOR CONTROL SYSTEMS  
Five color presets (9300/7500/sRGB/USER/NATIVE) select the desired color setting.  
COLOR RED  
Increases or decreases Red. The change will appear on screen.  
COLOR GREEN  
Increases or decreases Green. The change will appear on screen.  
COLOR BLUE  
Increases or decreases Blue. The change will appear on screen.  
TOOL  
Selecting TOOL allows you to get into the sub menu. See page 14.  
OSD TOOL  
Selecting OSD TOOL allows you to get into the sub menu. See page 14.  
FACTORY PRESET  
Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings except MUTE,  
CARBON SAVINGS, CARBON USAGE, and SIGNAL INFORMATION. Individual settings can be reset by highlighting  
the control to be reset and touching the INPUT/RESET key.  
EXIT  
Selecting EXIT allows you to exit OSD menu/sub menu.  
English-13  
TOOL  
EXPANSION  
Selects the zoom mode.  
This function works, when input signal timing is under native resolution.  
FULL: The image is expanded to full screen, regardless of the resolution.  
ASPECT: The image is expanded without changing the aspect ratio.  
RESPONSE IMPROVE (E203Wi only)  
Turns the Response Improve function ON or OFF.  
Response Improve may reduce blurring that occurs in some moving images.  
DDC/CI  
This function allows the DDC/CI function ON or OFF.  
CARBON SAVINGS  
Displays the estimated carbon saving information in kg.  
The carbon footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).  
The carbon saving information can be reset by touching the INPUT/RESET key.  
CARBON USAGE  
Displays the estimated carbon usages information in kg.  
This is the arithmetic estimation, not actual measurement value.  
The carbon footprint factor in the carbon usage calculation is based on the OECD (2008 Edition).  
The carbon usage information can be reset by touching the INPUT/RESET key.  
MONITOR INFO  
Indicates the model and serial numbers of your monitor.  
SOUND INPUT (DisplayPort input only) (E233WM only)  
This function selects AUDIO IN or DP.  
INPUT RESOLUTION (Analog input only)  
This function works, when user selects below special input signal timing.  
Select resolution’s priority of input signal to one of the following signal: 1280x768, 1360x768 and 1366x768 or  
1400x1050* and 1680x1050*.  
1280x768, 1360x768, 1366x768: Determines the resolution to 1280x768, 1360x768 or 1366x768.  
1400x1050*, 1680x1050*: Determines the resolution to 1400x1050 or 1680x1050.  
* E233WM only.  
OSD TOOL  
LANGUAGE  
OSD control menus are available in nine languages.  
OSD TURN OFF  
The OSD control menu will stay on as long as it is in use. In the OSD TURN OFF sub menu, you can select how  
long the monitor waits after the last touch of a key to shut off the OSD control menu. The preset choices are  
10 - 120 seconds by 5 seconds step.  
OSD LOCK OUT  
This control completely locks out access to all OSD control functions except for VOLUME (E233WM only),  
BRIGHTNESS and CONTRAST. To activate the OSD LOCK OUT function, enter the OSD TOOL sub menu, select  
“OSD LOCK OUT”, touch and hold the “INPUT/RESET” key and “+” simultaneously until “OSD LOCKED OUT”  
indicator appears. To deactivate, touch the SELECT key, then repeat the same steps until OSD main menu displays on  
screen.  
SIGNAL INFORMATION  
If you select “ON”, monitor displays “VIDEO INPUT MENU” after changing the input.  
If you select “OFF”, monitor doesn’t display “VIDEO INPUT MENU” after changing the input.  
English-14  
OSD Warning  
OSD Warning menus disappear by touching the SELECT key.  
NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or when there is a  
change of input signal or video is inactive, the NO SIGNAL window will appear.  
OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After the power  
is turned on or there is a change of input signal or the video signal doesn’t have proper timing, the OUT OF RANGE  
menu will appear.  
English-15  
Specifications - E203Wi  
Monitor Specifications  
MultiSync E203Wi Monitor  
Notes  
LCD Module  
Diagonal: 49.41 cm/20 inches  
Viewable Image Size: 49.41 cm/20 inches  
Native Resolution (Pixel Count): 1600 x 900  
Active matrix; thin film transistor (TFT) liquid crystal  
display (LCD); 0.271 (H) x 0.263 (V) mm dot pitch;  
250 cd/m2 white luminance; 1000:1 contrast ratio  
(typical), (25000:1 Contrast ratio, DV MODE ON).  
Input Signal  
DisplayPort:  
DisplayPort Connector: Digital RGB  
DVI-D 24pin: Digital RGB  
DisplayPort Complies with Standard V1.2,  
applicable to HDCP  
DVI:  
DVI (HDCP)  
VGA:  
15pin Mini D-sub: Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
Separate sync.TTL level Positive/Negative  
Display Colors  
16,777,216  
Depends on display card used.  
Synchronization Range  
Horizontal: 31.5 kHz to 81.1 kHz  
Vertical: 56 Hz to 76 Hz  
Automatically  
Automatically  
Viewing Angle  
Left/Right:  
Up/Down:  
89° (CR > 10)  
89° (CR > 10)  
Resolutions Supported (Some systems may  
not support all modes listed).  
720 x 400*1 VGA text  
640 x 480*1 at 60 Hz to 75 Hz  
800 x 600*1 at 56 Hz to 75 Hz  
832 x 624*1 at 75 Hz  
1024 x 768*1 at 60 Hz to 75 Hz  
1152 x 870*1 at 75 Hz  
1440 x 900*1 at 60 Hz  
1600 x 900 at 60 Hz............................................. NEC DISPLAY SOLUTIONS cites recommended  
resolution for optimal display performance.  
Active Display Area  
Landscape: Horiz.: 433.9 mm/17.1 inches  
Vert.: 236.3 mm/9.3 inches  
Portrait: Horiz.: 236.3 mm/9.3 inches  
Vert.: 433.9 mm/17.1 inches  
Power Supply  
Current Rating  
Dimensions  
100 - 240 V ~ 50/60 Hz  
0.35 - 0.20 A  
Landscape: 466.0 mm (W) x 350.0 - 460.0 mm (H) x 213.9 mm (D)  
18.3 inches (W) x 13.8 - 18.1 inches (H) x 8.4 inches (D)  
Portrait: 273.2 mm (W) x 482.4 - 556.4 mm (H) x 213.9 mm (D)  
10.8 inches (W) x 19.0 - 21.9 inches (H) x 8.4 inches (D)  
Height Adjustment: 110 mm / 4.3 inches (Landscape orientation)  
74.0 mm / 2.9 inches (Portrait orientation)  
Weight  
4.9 kg (10.8 lbs) (with stand)  
Environmental Considerations  
Operating Temperature: 5°C to 35°C/41°F to 95°F  
Humidity: 20% to 80%  
Altitude: 0 to 6,562 Feet/0 to 2,000 m  
Storage Temperature: -10°C to 60°C/14°F to 140°F  
Humidity: 10% to 85%  
Altitude: 0 to 40,000 Feet/0 to 12,192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and  
necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually one  
pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-16  
Specifications - E233WM  
Monitor Specifications  
MultiSync E233WM Monitor  
Notes  
LCD Module  
Diagonal: 58.42 cm/23 inches  
Viewable Image Size: 58.42 cm/23 inches  
Native Resolution (Pixel Count): 1920 x 1080  
Active matrix; thin film transistor (TFT) liquid crystal  
display (LCD); 0.265 mm dot pitch; 250 cd/m2 white  
luminance; 1000:1 contrast ratio (typical), (25000:1  
Contrast ratio, DV MODE ON).  
Input Signal  
DisplayPort:  
DisplayPort Connector: Digital RGB  
DVI-D 24pin: Digital RGB  
DisplayPort Complies with Standard V1.2,  
applicable to HDCP  
DVI:  
DVI (HDCP)  
VGA:  
15pin Mini D-sub: Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
Separate sync.TTL level Positive/Negative  
Display Colors  
16,777,216  
Depends on display card used.  
Synchronization Range  
Horizontal: 31.5 kHz to 81.1 kHz  
Vertical: 56 Hz to 76 Hz  
Automatically  
Automatically  
Viewing Angle  
Left/Right:  
Up/Down:  
85° (CR > 10)  
80° (CR > 10)  
Resolutions Supported (Some systems may  
not support all modes listed).  
720 x 400*1 VGA text  
640 x 480*1 at 60 Hz to 75 Hz  
800 x 600*1 at 56 Hz to 75 Hz  
832 x 624*1 at 75 Hz  
1024 x 768*1 at 60 Hz to 75 Hz  
1152 x 870*1 at 75 Hz  
1280 x 960*1 at 60 Hz  
1280 x 1024*1 at 60 Hz to 75 Hz  
1440 x 900*1 at 60 Hz  
1680 x 1050*1 at 60 Hz  
1920 x 1080 at 60 Hz........................................... NEC DISPLAY SOLUTIONS cites recommended  
resolution for optimal display performance.  
Active Display Area  
Landscape: Horiz.: 509.2 mm/20.0 inches  
Vert.: 286.4 mm/11.3 inches  
Portrait: Horiz.: 286.4 mm/11.3 inches  
Vert.: 509.2 mm/20.0 inches  
AUDIO  
AUDIO Input:  
STEREO Mini Jack: Analog Audio  
DisplayPort Connector: Digital Audio  
Stereo L/R 1.0 Vrms 20 Kohm  
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)  
Headphone Output: STEREO Mini Jack:  
Speakers Practical Audio Output: 1.0 W + 1.0 W  
100 - 240 V ~ 50/60 Hz  
0.55 - 0.30 A  
Headphone Impedance 32 Ohm  
Power Supply  
Current Rating  
Dimensions  
Landscape: 544.3 mm (W) x 374.5 - 484.5 mm (H) x 213.9 mm (D)  
21.4 inches (W) x 14.7 - 19.1 inches (H) x 8.4 inches (D)  
Portrait: 322.2 mm (W) x 560.8 - 595.6 mm (H) x 213.9 mm (D)  
12.7 inches (W) x 22.1 - 23.4 inches (H) x 8.4 inches (D)  
Height Adjustment: 110 mm / 4.3 inches (Landscape orientation)  
34.8 mm / 1.4 inches (Portrait orientation)  
Weight  
5.7 kg (12.6 lbs) (with stand)  
Environmental Considerations  
Operating Temperature: 5°C to 35°C/41°F to 95°F  
Humidity: 20% to 80%  
Altitude: 0 to 6,562 Feet/0 to 2,000 m  
Storage Temperature: -10°C to 60°C/14°F to 140°F  
Humidity: 10% to 85%  
Altitude: 0 to 40,000 Feet/0 to 12,192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and  
necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually one  
pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-17  
Features  
Reduced Footprint: Provides the ideal solution for environments with space constraints that still require superior image quality.  
The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another.  
Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a  
variety of standards.  
OSD (On-Screen Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use  
on-screen menus.  
NaViSet Software offers an expanded and intuitive graphical interface, allowing you to more easily adjust OSD display settings  
via mouse and keyboard.  
No Touch Auto Adjust (Analog input only): Automatically adjusts the monitor to optimal settings upon initial setup.  
ErgoDesign Features: Enhanced human ergonomics to improve the working environment, protect the health of the user and  
save money. Examples include OSD controls for quick and easy image adjustments, tilt base for preferred angle of vision, small  
footprint and compliance with MPRII and TCO guidelines for lower emissions.  
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing  
the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically  
optimizing display performance.  
Intelligent Power Manager System: Provides innovative power-saving methods that allow the monitor to shift to a lower power  
consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and lowering the  
air conditioning costs of the workplace.  
Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the  
resolution required.  
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.  
VESA Standard Mounting Interface: Allows users to connect your monitor to any VESA standard third party mounting arm or  
bracket.  
Environmental Impact (E203Wi): Annual typical maximum operating carbon footprint of this monitor (world-wide average) is  
approximately 15.4 kg (calculated by: rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power-to-Carbon  
conversion factor - conversion factor is based on OECD publication of global CO2 emissions 2008 Edition).  
This monitor has a manufacturing carbon footprint of approximately 36.0 kg.  
Environmental Impact (E233WM): Annual typical maximum operating carbon footprint of this monitor (world-wide average) is  
approximately 27.2 kg (calculated by: rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power-to-Carbon  
conversion factor - conversion factor is based on OECD publication of global CO2 emissions 2008 Edition).  
This monitor has a manufacturing carbon footprint of approximately 36.7 kg.  
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC  
for its monitors and are accurate at the time of printing. NEC reserves the right to publish updated carbon footprint values.  
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent  
over a digital signal. If you are unable to view material via the digital input, this does not necessarily mean the display is not  
functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and  
might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).  
DisplayPort: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display  
connectivity. It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables.  
English-18  
Troubleshooting  
No picture  
The signal cable should be completely connected to the display card/computer.  
The display card should be completely seated in its slot.  
The monitor does not support DisplayPort converter adapter.  
Front Power Switch and computer power switch should be in the ON position.  
Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult  
display card or system manual to change graphics mode.)  
Check the monitor and your display card with respect to compatibility and recommended settings.  
Check the signal cable connector for bent or pushed-in pins.  
Check the signal input.  
Power key does not respond  
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.  
When something is stuck on the bezel, key becomes unresponsive.  
Image persistence  
Image persistence is when a “ghost” of an image remains on the screen even after the monitor has been turned off. Unlike CRT  
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time  
should be avoided.  
To alleviate image persistence, turn the monitor off for as long as an image was displayed. For example, if an image was on the  
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.  
NOTE:  
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a screen saver at regular intervals  
whenever the screen is idle or turning off the monitor when not in use.  
Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only)  
Image is displayed only roughly (pixels are missing) and OSD warning “OUT OF RANGE” is displayed: Either signal clock or  
resolution is too high. Choose one of the supported modes.  
OSD warning “OUT OF RANGE” is displayed on a blank screen: Signal frequency is out of range. Choose one of the supported  
modes.  
Image is unstable, unfocused or swimming is apparent  
Signal cable should be completely attached to the computer.  
Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine total. When the display  
mode is changed, the OSD Image Adjust settings may need to be re-adjusted.  
Check the monitor and your display card with respect to compatibility and recommended signal timings.  
If your text is garbled, change the video mode to non-interlace and use 60 Hz refresh rate.  
Picture is not as bright  
Make sure ECO MODE is turned off.  
Signal cable should be completely attached.  
LCD brightness degradation occurs due to long-term usage or extreme cold conditions.  
LED on monitor is not lit (no blue or amber color can be seen)  
Power Switch should be in the ON position and power cord should be connected.  
Display image is not sized properly  
Use the OSD Image Adjust controls to increase or decrease the H.SIZE.  
Check to make sure that a supported mode has been selected on the display card or system being used.  
(Please consult display card or system manual to change graphics mode.)  
No Video  
If no video is present on the screen, turn the Power key off and on again.  
Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).  
Some display cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power cord  
under low resolution with DisplayPort.  
No Sound (E233WM)  
Check to see if speaker cable is properly connected.  
Check to see if mute is activated.  
Check the volume in the OSD menu.  
Check selected OSD’s Tools “SOUND INPUT”, when DisplayPort is in use.  
Brightness variations over time  
Change DV MODE to OFF and adjust brightness.  
NOTE:  
When DV MODE is set to ON, the monitor automatically adjusts brightness based on the environment.  
When the brightness of surrounding environment changes, the monitor will also change.  
English-19  
TCO Certified Displays 6  
Congratulations!  
This product is TCO Certified – for Sustainable IT  
TCO CertiÞed is an international third party sustainability certiÞcation for  
IT products. TCO CertiÞed ensures that the manufacture, use and  
recycling of IT products reßect environmental, social and economic  
responsibility. Every TCO CertiÞed product model is veriÞed by an  
accredited independent test laboratory.  
This product has been veriÞed to meet all the criteria in TCO CertiÞed, including:  
Corporate Social Responsibility  
Socially responsible production - working conditions and labor law in manufacturing country  
Energy EfÞciency  
Energy efÞciency of product and power supply. Energy Star compliant, where applicable  
Environmental Management System  
Manufacturer must be certiÞed according to either ISO 14001 or EMAS  
Minimization of Hazardous Substances  
Limits on cadmium, mercury, lead & hexavalent chromium including requirements for mercury-free  
products, halogenated substances and hazardous ßame retardants  
Design for Recycling  
Coding of plastics for easy recycling. Limit on the number of different plastics used.  
Product Lifetime, Product Take Back  
Minimum one-year product warranty. Minimum three-year availability of spare parts. Product takeback  
Packaging  
Limits on hazardous substances in product packaging. Packaging prepared for recycling  
Ergonomic, User-centered design  
Visual ergonomics in products with a display. Adjustability for user comfort (displays, headsets)  
Acoustic performance – protection against sound spikes (headsets) and fan noise (projectors, computers)  
Ergonomically designed keyboard (notebooks)  
Electrical Safety, minimal electro-magnetic Emissions  
Third Party Testing  
All certiÞed product models have been tested in an independent, accredited laboratory.  
A detailed criteria set is available for download at www.tcodevelopment.com, where you can also  
Þnd a searchable database of all TCO CertiÞed IT products.  
TCO Development, the organization behind TCO CertiÞed, has been an international driver in the  
Þeld of Sustainable IT for 20 years. Criteria in TCO CertiÞed are developed in collaboration with  
scientists, experts, users and manufacturers. Organizations around the world rely on TCO CertiÞed  
as a tool to help them reach their sustainable IT goals. We are owned by TCO, a non-proÞt  
organization representing ofÞce workers. TCO Development is headquartered in Stockholm,  
Sweden, with regional presence in North America and Asia.  
For more information, please visit  
English-20  
Manufacturer’s Recycling and Energy Information  
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s  
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-  
friendly products, and always strive to help define and comply with the latest independent standards from agencies such as  
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).  
Disposing of your old NEC product  
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of  
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely  
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures  
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.  
All required information concerning the disposal of the product and country-specific information on recycling facilities can be  
found on our following websites:  
Energy Saving  
This monitor features an advanced energy saving capability. When a Display Power Management signal is sent to the monitor,  
the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.  
Mode  
Power consumption  
LED color  
17 W (E203Wi)  
30 W (E233WM)  
Maximum Operation  
Blue  
15 W Default setting (E203Wi)  
19 W Default setting, Audio sleeping (E233WM)  
Normal Operation  
Blue  
Energy Saving Mode  
Off Mode  
0.35 W  
0.30 W  
Amber  
Unlit  
For additional information visit:  
For Energy Saving information:  
For ErP/EnergyStar requirement:  
Setting: None.  
Power consumption: 0.5 W or less.  
Time for power management function: Approx. 1 min.  
For ErP (Network standby) requirement:  
Setting: None.  
Power consumption: 0.5 W or less (with 1 port activating) / 6.0 W or less (with all ports activating).  
Time for power management function: Approx. 1 min.  
WEEE Mark (European Directive 2012/19/EU)  
Within the European Union  
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic  
products carrying the mark (left) must be disposed of separately from normal household waste. This includes  
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your  
NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased  
the product, or if applicable, follow any agreements made between yourself and NEC.  
The mark on electrical and electronic products only applies to the current European Union Member States.  
Outside the European Union  
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority  
so as to comply with the correct disposal method.  
English-21  

Sharp Air Cleaner Kc 850u User Manual
Ricoh Aficio 8070 User Manual
MIELE HR 1954 3 DF User Manual
Manual Handy Heater User Manual
LG 43US670H0UA User Manual
Lexmark Intuition S508 User Manual
KENWOOD M A300 User Manual
GE ARC15AAC User Manual
DETROIT RADIANT SW 24 User Manual
CRAFTSMAN 320.64180 User Manual