Maxx Ice Mim50 User Manual

INSTRUCTION  
MANUAL  
MIM50-0  
Automatic Outdoor Ice Maker  
English  
MIM50-0MAN 0511 REV A  
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE  
IMPORTANT SAFEGUARDS  
Before the ice maker is used, it must be properly positioned and installed as described  
in this manual, so read the manual carefully. MAXX ICE strongly recommends that you  
have a professional install your new machine. The warranty may be affected or voided  
by an incorrect installation .To reduce the risk of fire, electrical shock or injury when  
using the ice maker, follow basic precautions, including the following:  
โ€ข
Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use  
adapter, and do not use an extension cord.  
It is recommended that a separate circuit, serving only your ice maker, be provided.  
Use receptacles that cannot be turned off by a switch or pull chain.  
โ€ข
โ€ข
โ€ข
Do not connect or disconnect the electric plug when your hands are wet.  
Never unplug the icemaker by pulling on the power cord. Always grip the plug firmly  
and pull straight out from the outlet.  
Never clean ice maker parts with flammable fluids. Do not store or use gasoline or  
โ€ข
other flammable vapors and liquids in the vicinity of this or any other appliance. The  
fumes can create a fire hazard or explosion.  
โ€ข
Before proceeding with cleaning and maintenance operations, make sure the  
power line of the unit is disconnected and the water line is shut off. (EXCEPTION: When  
cleaning the machineโ€™s ice making and water systems - See pages 23-25)  
โ€ข
โ€ข
โ€ข
โ€ข
Before operating, put all panels back into place.  
Never allow children to operate, play with or crawl inside the ice maker.  
Do not touch the evaporator by hand when the machine is operating.  
Unplug the ice maker or disconnect power before cleaning or servicing. Failure to  
do so can result in electrical shock or death.  
Do not attempt to repair or replace any part of your ice maker unless it is specifically  
โ€ข
recommended in this manual. All other servicing should be referred to a qualified tech-  
nician.  
โ€ข
Use two or more people to move and install ice maker. Failure to do so can result in  
back or other injury.  
To ensure proper ventilation for your ice maker, the front of the unit must be com-  
โ€ข
pletely unobstructed. Choose a well-ventilated area with temperatures above 45ยฐF (7ยฐC)  
and below 110ยฐ F (43ยฐC).  
โ€ข
The ice maker should not be located next to ovens, grills or other sources of high  
heat.  
โ€ข
The ice maker must be installed with all electrical and water connections in accor-  
dance with state and local codes. A standard electrical supply (115VAC, 60Hz, 15A),  
properly grounded in accordance with the National Electrical Code and local codes  
and ordinances is required.  
โ€ข
โ€ข
Do not kink or pinch the power supply cord between the ice maker and cabinet.  
The fuse (or circuit breaker) size should be 15 amperes.  
โ€ข
It is important for the ice maker to be leveled in order to work properly. You may need  
to make several adjustments to level it.  
โ€ข
โ€ข
All installations must be in accordance with local plumbing code requirements.  
Make certain that the hoses are not pinched or kinked or damaged during installa-  
tion.  
โ€ข
โ€ข
Check for leaks after connection.  
Although the unit has been tested at the factory, due to long-term transit and stor-  
age, the first batch of cubes must be discarded.  
โ€ข
โ€ข
Remove the packing materials and clean the ice maker before using.  
Turn on the water supply tap before switching on the ice maker. Never turn the water  
supply tap off when the ice maker is working.  
Except to take ice from the unit, keep the door closed in order to reduce ice melting  
and to promote proper ice formation.  
If the ice maker will not be used for a long time, before the next use it must be thor-  
โ€ข
โ€ข
oughly cleaned. Follow carefully any instructions provided for cleaning or use of sanitizing  
solution. Do not leave any solution inside the ice maker after cleaning.  
โ€ข
DO NOT touch the condenser fins. The condenser fins are sharp and can be easily  
damaged.  
โ€ข
DO NOT use solvent-based cleaning agents or abrasives on the interior. These clean-  
ers may transmit taste to the ice cubes, or damage or discolor the interior.  
โ€ข
The ice machine cleaner contains acids. DO NOT use or mix with any other solvent-  
based cleaner products. Use rubber gloves to protect hand. Carefully read the material  
safety instructions on the container of the ice machine cleaner.  
โ€ข
Do not use this apparatus for other than its intended purpose.  
Electrical Connection  
Do not, under any circumstances, cut or remove the third (ground) prong from the power  
cord. For personal safety, this appliance must be properly grounded. The power cord of  
this appliance is equipped with a 3-prong grounding plug that mates with a standard 3-  
prong grounding wall outlet to minimize the possibility of electric shock hazard from the  
appliance. Have the wall outlet and circuit checked by a qualified electrician to make  
sure the outlet is properly grounded. When a standard 2-prong wall outlet is encountered,  
it is your responsibility and obligation to have it replaced with a properly grounded 3-  
prong wall outlet. The ice maker should always be plugged into its own individual elec-  
trical outlet which has a voltage rating that matches the rating label on the appliance.  
This provides the best performance and also prevents overloading house wiring circuits  
which could cause a fire hazard from overheated wires. Never unplug your ice maker  
by pulling on the power cord. Always grip the plug firmly and pull straight out from the  
outlet. Repair or replace immediately all power cords that have become frayed or oth-  
erwise damaged. Do not use a cord that shows cracks or abrasion damage along its  
length or at either end. When moving the ice maker, be careful not to damage the  
power cord.  
Extension Cord Because of potential safety hazards under certain conditions, it is strongly  
recommended that you do not use an extension cord with this ice maker.  
3
TECHNICAL SPECIFICATIONS  
MIM50-0  
115VAC ~ 60Hz  
Model:  
Electrical power:  
13.2kWh/100 lbs of ice  
3.7A/4.8A  
R134a 7.06oz  
Power consumption:  
Ice-making/Ice-harvest rated current:  
Refrigerant:  
High/Low Side Pressure:  
Width ร— Depth ร— Height (with feet):  
350psig/130psig  
14.6โ€ร—23.6โ€ร—33.5โ€  
370.84mm x 599.44mm x 850.9mm  
14.6โ€ร—23.6โ€ร—34.9โ€  
370.84mm x 599.44mm x 886.46mm  
88 lbs/39.91kg  
44 lbs/19.95kg - day  
*25 lbs/11.3kg  
Cube  
ยพโ€ ร— ยพโ€ ร— 1โ€  
19.05mm ร— 19.05mm ร— 25.4mm  
Width ร— Depth ร— Height (with casters)  
Unit weight:  
Ice-making capacity:  
Max. ice storage:  
Ice shape:  
Ice cube dimensions:  
The technical data and performance index listed above should be used for refer-  
ence only. They are subject to change. * The actual quantity of ice produced per  
day can vary with room and water conditions. Fahrenheit or degrees Celsius will ap-  
LOCATIONS OF PARTS  
4
INSTALLATION  
Remove packaging materials  
IMPORTANT: Do not remove any permanent instruction labels or the data label on  
your ice maker.  
Remove tape and glue from your ice maker before using.  
โ€ข
To remove any remaining tape or glue, rub the area briskly with your thumb. Tape  
or glue residue can also be easily removed by rubbing a small amount of liquid dish  
soap over the adhesive with your fingers. Wipe with warm water and dry.  
โ€ข
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive  
cleaners to remove tape or glue. These products can damage the surface of your  
ice maker.  
Cleaning before use  
After you remove all of the packaging materials, clean the inside of your ice maker  
before using it. See "Interior cleaning" in the Cleaning and Maintenance section.  
Location Requirements  
INSTALLATION CLEARANCES  
โ€ข
โ€ข
This ice maker should be installed by qualified personnel.  
To ensure proper ventilation for your ice maker, the front of the unit must be com-  
pletely unobstructed.  
When installing the ice maker under a counter, follow the recommended spacing  
โ€ข
dimensions shown on the previous page. Allow 2/5" (10mm) or more clearance at  
rear, 1/5" (5.1mm) at the sides and 1" (25.4mm) at the top for proper air circulation.  
The installation should allow the ice maker to be pulled forward for servicing if neces-  
sary.  
โ€ข
Choose a well-ventilated area with temperatures above 45ยฐF (7ยฐC) and below  
110ยฐ F (43ยฐC).  
โ€ข
โ€ข
The unit should not be located next to ovens, grills or other sources of high heat.  
Installation of the ice maker requires a cold water supply inlet of 1/4โ€ (6.35mm)  
5
INSTALLATION  
soft copper tubing with a shut-off valve.  
โ€ข
The ice maker requires a continuous water supply with a minimum pressure of 15  
psig and a static pressure not to exceed 80 psig. The temperature of the water feed-  
ing into the ice maker should be between 41ยฐF (5ยฐC) and 90ยฐF (32ยฐC) for proper oper-  
ation.  
WARNING: Normal operating ambient temperature should be between 45ยฐF (7ยฐC) to  
110ยฐ F (43ยฐC). Normal operating water temperature should be between 41ยฐF (5ยฐC)  
and 90ยฐF (32ยฐC). Operation of the ice maker for extended periods outside of these  
normal temperature ranges may affect production capacity.  
โ€ข
It is strongly recommended that a water filter be used. A filter, if it is of the proper  
type, can remove taste and odors as well as particles. Some water is very hard; soft-  
ened water may result in white, mushy cubes that stick together. De-ionized water is  
not recommended.  
โ€ข
The ice maker must be installed with all electrical and water connections in ac-  
cordance with all state and local codes.  
The unit should be located on a firm and level surface. It is important for the ice  
โ€ข
maker to be leveled in order to work properly. If needed, you can adjust the height  
of the ice maker by rotating the casters or adjustable feet. See the Leveling the Ice  
Maker section.  
โ€ข
A standard electrical supply (115V AC only, 60Hz, 15A), properly grounded in ac-  
cordance with the National Electrical Code and local codes and ordinances, is re-  
quired.  
โ€ข
IMPORTANT: Do not kink or pinch the power supply cord between the ice maker  
and wall or cabinet.  
Electrical Requirements  
Electrical Shock Hazard: Plug into a grounded 3- prong outlet.  
Never remove the ground prong from the plug.  
Never use an adapter.  
Never use an extension cord.  
Failure to follow these instructions can result in fire, electrical shock or death.  
Before you move your ice maker into its final location, be sure you have the proper  
electrical connection:  
A standard electrical supply (115V AC only, 60Hz, 15A), properly grounded in accor-  
dance with the National Electrical Code and local codes and ordinances, is re-  
quired.  
6
INSTALLATION  
** The ice maker should always be plugged into its own individual electrical outlet. **  
It is recommended that a separate circuit, serving only your ice maker, be provided.  
Use receptacles that cannot be turned off by a switch or pull chain.  
The fuse (or circuit breaker) size should be 15 amperes.  
Recommended grounding method  
For your personal safety, this appliance must be grounded. It is equipped with a  
power supply cord having a 3-prong grounding plug. To minimize a possible shock  
hazard, the cord must be plugged into a mating 3-pronged and grounding-type wall  
receptacle, grounded in accordance with the National Electrical Code and local  
codes and ordinances. If a mating wall receptacle is not available, it is the personal  
responsibility of the customer to have a properly grounded, 3-prong wall receptacle  
installed by a qualified electrician.  
Installation of Casters  
Casters are provided with  
the ice maker. They are  
ideal for rolling the unit  
Screw holes  
from place to place out-  
doors. If a mobile installa-  
tion is chosen, you must  
install the casters.  
Use two or more people when installing or removing casters  
โ€ข
Tip unit to the right so there is a 3/4-foot clearance at the left of the unit. Have  
someone to assist you in tilting the unit, to prevent it from falling on you while installing  
the casters.  
โ€ข
Screw one of the casters with lock in the front screw impression and screw one of  
the casters without lock in the back screw impression.  
Repeat the two steps above with the exception of tipping the unit to the left  
now, to screw in the other two casters.  
โ€ข
โ€ข
โ€ข
The casters are now installed.  
The unit should be level. If the floor conditions do not allow the unit to sit level, ad-  
just the wheel by turning the required wheel counter-clockwise to increase their  
height and clockwise to reduce their height.  
7
INSTALLATION  
Leveling the Ice Maker  
It is important for the ice maker to  
be leveled in order to work properly;  
otherwise water will not flow as it  
should through the evaporator (ice  
mold). Ice production will be less  
than normal, and operation will be  
noisy. The ice maker can be raised  
or lowered by four leveling legs on  
the bottom of the machine. If you  
find that the surface is not level. You  
may need to make several adjust-  
ments to level the machine. We rec-  
ommend using a carpenterโ€™s level  
to check it.  
1. Place a carpenterโ€™s level on top of the product to see if the ice maker is level  
from front to back and side to side.  
2. Adjust the height of the legs as follows:  
Turn the leveling legs to the right to lower that side of the ice maker.  
Turn the leveling legs to the left to raise that side of the ice maker.  
IMPORTANT: Once you are ready to install it in a cabinet or directly on the floor, you  
must adjust the legs to level the ice maker.  
Reversing the Door Swing  
TOOLS NEEDED: Flat screwdriver, Phillips screwdriver  
IMPORTANT: Before you begin, unplug the ice maker or disconnect power.  
To remove door from hinges:  
1. Remove the top hinge  
cover.  
2. Using a Phillips screwdriver,  
remove the screws, then remove  
top hinge mat and top hinge.  
Keep the parts together and set  
them aside.  
3. Lift the door off of the bot-  
tom hinge and turn it upside  
down so that the handle is on  
the right. Set the door aside.  
8
To replace door on hinges:  
1. Using a flat screwdriver, remove the plug buttons from the screw holes opposite  
the door hinges, top and bottom. Set aside.  
2. Remove the bottom hinge and place it on the opposite side at the bottom of the  
door.  
3. Position the door on the bottom hinge.  
4. Align the door on the bottom hinge and replace the top hinge and top hinge  
mat.  
5. Replace top hinge cover.  
6. Push the plug buttons into the original screw holes.  
Water Supply  
The water supply should be ready at the point of installation. The water supply pres-  
sure should be a minimum of 15 psig with a static pressure not more than 80 psig. (A  
wall outlet directly behind the ice machine will make installation easier.)  
IMPORTANT:  
โ€ข
All installations must be in accordance with local  
plumbing code requirements. Professional installation is  
recommended.  
โ€ข
Make certain that the hoses are not pinched or  
kinked or damaged during installation.  
Check for leaks after connection.  
Rear of unit  
โ€ข
Water inlet  
Drain outlet  
Tools required: 1/2โ€ open-end wrenches,  
Phillips screwdriver  
Connecting the water line:  
1. Turn off main water supply. Turn on the nearest faucet long enough to clear the  
line of water.  
2. Find a 1/2โ€ to 3/4โ€ vertical cold water pipe near the installation location. The dis-  
tance should be less than 9 feet. The water supply hose provided with the ice maker  
is about 9 feet.  
3. A shut-off valve must be installed to the main water supply. If the water pipe has a  
plain piece of copper tubing, attach a 1/4โ€ O.D. compression union to the tubing  
and remove the nut.  
4. Connect nuts of water supply hose to the tap, and connect the other end with the  
water inlet. Tighten firmly by hand, then one-half turn with wrench.  
5. Turn on main water supply and tap. Check for water supply connections leaks.  
Tighten every connection (including connections at the water inlet).  
When you connect the water supply hose and the drain hose, pay attention to the  
indications of โ€œWater inletโ€ and โ€œDrain outletโ€ on the machine.  
9
Drain  
IMPORTANT: This ice maker is not a freezer, it must connect to a drain line. Your ma-  
chine comes equipped with a gravity drain. Depending on your plumbing setup, a  
condensation pump may be required. Poor drainage will cause a high rate of melt-  
ing in the ice storage bin and may cause flooding or your machine to shut off.  
Connecting the drain line:  
NOTE: If there is a drain line near the ice maker or the ice maker will be used as an  
outdoor unit, the best choice is to drain water to the drain line through the drain hose  
provided with ice maker.  
1. Locate the floor drain near the ice maker. The distance should be less than 5 feet  
since the length of the long drain hose provided with the ice maker is about 5 feet.  
Find the drain outlet on the back of ice maker, then take off the rear drainage plug.  
Connect the nut of the drain outlet to the water draining hose, and insert the other  
side of the hose into the drain line.  
NOTE: The drain hose should never be allowed to hang or loop higher than the bot-  
tom of the ice storage bin.  
2. All horizontal runs of drain lines must have a fall of 1/4โ€ per foot. An air gap will  
likely be required between the ice maker drain hose and the drain/waste recepta-  
cle. A stand pipe with a trap below it would be acceptable for the drain/waste re-  
ceptacle. A floor drain is also acceptable.  
3. Pour 1 gallon of water into the ice storage bin to check for leaks at all drain con-  
nections and at the nut of the drain water hole. Tighten any connections or nuts that  
leak.  
Installation Types  
This ice maker has been designed for Mobile (free-standing), Enclosed (as under a  
cabinet) or Built-in (sealed) installation, indoor or outdoor. In any case, there must be  
adequate air space around the unit for proper ventilation.  
Mobile installation:  
A mobile installation will allow you to install the ice maker free-standing in any place  
you desire provided you have access to a water supply. You must follow the stated  
instructions for  
a. Electrical requirements  
b. Water supply  
c. Leveling the ice maker  
Enclosed Installation:  
An enclosed installation will allow you to install the ice maker under a cabinet or in-  
side a kitchen cabinet provided the required clearance space around the ice maker  
is respected. This installation has the same requirements as a mobile installation.  
10  
Built-in Installation:  
If this method of installation is chosen, it will still be necessary to allow adequate venti-  
lation space around the unit. The following additional items must be observed.  
1. Place ice maker in front of installation location. Remove the legs and place the  
unit flat on the floor or on a platform depending on your installation requirements.  
2. The water supply line must be plumbed before connecting to the ice maker.  
3. Connect the drain hose.  
4. Turn on main water supply and tap. Check for water supply connection leaks.  
Tighten every connection (including connections at the water inlet).  
5. If the electrical outlet for the ice maker is behind the cabinet, plug in the ice  
maker.  
6. Push the ice maker into position.  
7. Seal all around the cabinet to the floor with an approved caulking compound.  
OPERATION:  
Final Check List before Operation  
1. Have all packing materials and tape been removed from the interior and exterior  
of the ice maker?  
2. Did you clean the ice storage bin?  
3. Have the installation instructions been followed, including connecting the machine  
to water, drain and electricity?  
4. Has the machine been leveled?  
5. Is the ice maker in a site where the ambient temperature is between 45ยฐF (7ยฐC)  
and 110ยฐF (43ยฐC) and the water temperature within 41ยฐF (5ยฐC) and 90ยฐF (32ยฐC) all  
year round?  
6. Has the water supply pressure been checked to ensure a minimum of 15 psig with  
a static pressure not to exceed 80 psig?  
7. Is there a clearance of at least 2/5โ€ณ at the rear, and 1โ€ at the top and 1โ„5โ€ณ at the  
sides for proper air circulation?  
8. Has the power supply voltage been checked or tested against the nameplate rat-  
ing? And has proper grounding been installed for the ice maker?  
9. Is the ice maker plugged in?  
10. Have you turned on the main water supply and the tap?  
11. Have you checked for leaks at all water supply connections?  
Operating Method  
1. Turn on the water tap and let the water trough fill. Then set the Power switch on  
the front panel to the ON position. The ice maker will start working automatically.  
11  
Cold  
preservation  
stage  
Ice-  
harvesting  
stage  
Ice-  
making  
stage  
2. After three minutes, the machine will automatically go into the ice-making stage,  
and the sound of flowing water will be heard.  
3. When the batch of ice has been fully formed, the ice will automatically be har-  
vested to the ice storage bin.  
4. When the ice storage bin is full, the sheet of cubes does not fall completely and it  
holds the ice-full probe open. The machine stops making ice and automatically pro-  
gresses to the cold preservation stage. During this stage, the compressor works regu-  
larly to keep the temperature low to reduce ice melting.  
5. The unit will start making ice again after the ice cubes are removed. Then the ice-  
full probe swings back to operating position.  
IMPORTANT:  
โ€ข
Although the unit has been tested and cleaned at the factory, due to long-term  
transit and storage, the first batch of cubes must be discarded.  
โ€ข
โ€ข
โ€ข
Never turn the water supply tap off when the ice maker is working.  
Never touch the evaporator when the machine is running!  
Except to take ice from the unit, keep the door closed to reduce ice melting and  
insure proper ice formation.  
How the Machine Makes Ice  
Turn the Power switch to the ON position. The Power indicator light will light and the  
machine will automatically go into the ice-making stage.  
There are two distinct cycles: freeze and harvest.  
During the freeze cycle, water flows to the evaporator surface. In the harvest cycle,  
the ice is released. A complete cycle can take 15 to 40 minutes, depending on tem-  
perature and operating conditions.  
Freeze: During the freeze cycle the compressor is pumping refrigerant, the fan motor  
is blowing air, and the water pump is circulating water. When the batch of ice has  
been fully formed, the ice maker stops the freeze cycle and begins the harvest  
cycle.  
Harvest: During the harvest cycle the compressor is still operating, but the water  
pump has stopped. The hot gas valve opens, diverting hot refrigerant gas into the  
evaporator. The hot refrigerant gas warms the evaporator, causing the cubes to slide,  
as a unit, off the evaporator and into the storage bin. The freeze cycle will restart  
when all the cubes have been harvested.  
12  
How the Machine Uses the Water  
The ice maker begins with a fixed  
charge of water that is contained in  
the water trough. As the water flows  
to the freezing evaporator surface,  
the portion of water that does not  
contain mineral impurities will freeze  
and stick to the ice cube molds. The  
water containing impurities falls  
back into the water trough. During  
the ice-making process, fresh water  
enters the water trough continu-  
ously as the water from the trough  
freezes continuously on the evapo-  
rator.  
Evaporator  
Water inlet  
Water pump  
Hot gas valve  
Condenser  
Fan  
motor  
Compressor  
Normal Sounds  
Your new ice maker may make sounds that are unfamiliar to you. Most of the new  
sounds are normal. Hard surfaces like the floor and walls can amplify the sounds. The  
following describes the kinds of sounds that might be new to you and what may be  
causing them.  
โ€ข
Rattling noises may come from the flow of the refrigerant or the water line. Items  
stored on top of the ice maker can also make noises.  
โ€ข
โ€ข
โ€ข
โ€ข
The high-efficiency compressor may make a pulsating or high-pitched sound.  
Running water may make a splashing sound.  
You may hear air being forced over the condenser by the condenser fan.  
During the harvest cycle, you may hear the sound of ice cubes falling into the ice  
storage bin.  
Preparing the Ice Maker for Long Storage  
If the ice maker will not be used for a long time, or is to be moved to another place, it  
will be necessary to drain the system of water.  
1. Shut off the water supply at the main water source.  
2. Disconnect the water supply line from the water inlet.  
3. Shut off the electric supply at main electrical power source.  
4. Take out the ice storage bin to remove remaining ice and water. Dry it.  
5. Connect the drain hose to drain out water completely, then plug up the drain  
outlet after finishing.  
6. Pull off the drainage tube of the water trough to drain off all water.  
7. Leave the door open to allow for circulation and to prevent mold and mildew.  
8. Leave water supply line and power cord disconnected until ready to reuse.  
IMPORTANT:  
โ€ข
โ€ข
Do not touch the power plug when your hands are wet.  
Never unplug the unit by pulling on the plug  
13  
CLEANING & MAINTANANCE:  
CAUTION: If the ice maker is left unused for a long time, before the next use it must be  
thoroughly cleaned. Follow carefully any instructions provided for cleaning or use of  
sanitizing solution. Do not leave any solution inside the ice maker after cleaning.  
Periodic cleaning and proper maintenance will ensure efficiency, top performance,  
and long life. The maintenance intervals listed are based on normal conditions. You  
may want to shorten the intervals if you have pets, or there are other special consid-  
erations.  
** Improper maintenance or neglect may result in your warranty being voided. **  
Never keep anything in the ice storage bin other than ice: objects like wine and beer  
bottles are not only unsanitary, but the labels may slip off and plug up the drain.  
What parts should be kept clean  
There are 5 things to keep clean:  
1. The exterior  
2. The interior  
3. The condenser  
4. Water distribution tube  
5. The ice-making system  
WARNING:Before proceeding with cleaning and maintenance operations, make sure  
the unitโ€™s power line is disconnected and the water line is shut off. (EXCEPTION:  
Cleaning of ice making system)  
Exterior Cleaning  
The door and cabinet may be cleaned with a mild detergent and warm water solu-  
tion such as 1 oz of dishwashing liquid mixed with 2 gallons of warm water. Do not use  
solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water.  
Wipe with a soft clean towel to prevent water spotting. Stainless steel can discolor  
when exposed to chlorine gas and moisture. Clean stainless steel with a mild deter-  
gent and warm water solution and a damp cloth. Never use an abrasive cleaning  
agent.  
Interior Cleaning  
The ice storage bin should be sanitized occasionally. Clean the trough before the ice  
maker is used for the first time and reused after stopping for an extended period of  
time. It is usually convenient to sanitize the trough after the ice-making system has  
been cleaned and the storage bin is empty.  
14  
1. Disconnect the power to the unit.  
2. Open the door and take out the removable ice storage bin. With a clean cloth,  
wipe down the interior of the unit with a sanitizing solution made of 1 ounce of house-  
hold bleach and 2 gallons of hot water (95ยบF to 115ยบF).  
3. Rinse thoroughly with clear water.  
4. Connect a hose to the drain outlet at the rear of the unit to drain water com-  
pletely.  
5. Put the ice storage bin inside the unit.  
6. Reconnect power to the unit.  
The ice scoop should be washed regularly. Wash it just like any other food container.  
WARNING:DO NOT use solvent-based cleaning agents or abrasives on the interior.  
These cleaners may transmit taste to the ice cubes and damage or discolor the inte-  
rior.  
Condenser Cleaning  
A dirty or clogged condenser prevents proper  
airflow, reduces ice making capacity, and  
causes higher-than-recommended operating  
temperatures that may lead to component fail-  
ure. Have the condenser cleaned at least once  
every six months.  
1. Unplug the ice maker or disconnect power.  
2. Remove the 2 screws on the front cover and gently pull it off.  
3. Locate the condenser filter. This can be lifted out and cleaned with a brush or  
flowing water.  
4. Remove dirt and lint from condenser fins and the unit compartment with a brush  
attachment on a vacuum cleaner.  
5. Put back the filter and reassemble the front cover.  
6. Plug in the ice maker or reconnect power.  
WARNING: DO NOT touch the condenser fins. They are sharp and can be damaged  
easily.  
Water Distribution Tube Cleaning  
When you find that the ice cubes are incompletely formed or the output of ice  
cubes is low, the water distribution tube may be blocked. Set the Power switch to  
OFF, rotate the water distribution tube, and locate the holes in the distribution tube.  
Using a toothpick or similar tool, dredge the holes, then rotate the water distribution  
tube back to its original position. If the tube is badly blocked, clean it as follows:  
1. Shut off the water supply.  
2. Disconnect the water hose from the distribution tube.  
3. Lift the right side up, then remove the distribution tube.  
15  
4. With a brush, clean the tube with a dilute solution of warm water and a mild de-  
tergent such as dishwashing liquid. After removing the dirt and lint from the surface,  
rinse the tube with clean water.  
5. Replace the distribution tube  
6. Reconnect the water supply.  
Ice-Making System Cleaning  
Minerals that are removed from water during the freezing cycle will eventually form a  
hard, scaly deposit in the water system. Cleaning the system regularly helps remove  
the mineral scale buildup. How often you need to clean the system depends upon  
how hard your water is or how effective your filtration may be. With hard water of 15  
to 20 grains/gal. (4 to 5 grains/liter), you may need to clean the system as often as  
once every 6 months.  
1. Make sure that all the ice is off the evaporator. If ice is being made, wait until the  
cycle is completed, then turn the machine OFF at the Power switch.  
2. Remove all ice from the storage bin.  
3. Keep the ice maker connected to the water supply. Pour 8 oz. of Nickel-Safe Ice  
Maker Cleaner Solution into the water trough. After about 5 minutes, set the Power  
switch to ON. At the same time press the Clean switch on the front of the unit, and  
the Clean indicator light will light, then initiate the Cleaning cycle. The machine will  
run the Automatic Clean Mode.  
NOTE: The unit will automatically shut down the Cleaning program after 30 minutes,  
or you can stop it by pressing the Clean switch again, and the machine will automat-  
ically progress to the ice-making stage.  
4. Allow 20 minutes for proper cleaning. After cleaning, turn the machine OFF at the  
Power switch. Drain off the waste water to a container by means of the drain hose at  
the front of the water trough.  
NOTE: Do not drain off the waste water to the inside of the cabinet.  
5. Repeat steps 3 and 4 (without Ice Maker Cleaning Solution) 3 times to rinse the  
ice making system.  
NOTE: The use of the Ice Maker Cleaner Solution in the water bin during the rinse is  
not needed.  
WARNING: The ice machine cleaner contains acids.  
DO NOT use or mix with any other solvent-based cleaner products.  
Use rubber gloves to protect hands. Carefully read the material safety instructions on  
the container of the ice machine cleaner.  
DISCARD the first batch of ice produced after cleaning.  
16  
6. Prepare a sanitizing solution made of 1 ounce of household bleach and 2 gallons  
of hot water (95ยบ to 115ยบF). Wipe the entire bin inside and outside, covering the entire  
surface of the walls.  
7. Fill a spray bottle with the sanitizing solution and spray all corners and edges mak-  
ing sure to cover all surfaces with the solution.  
8. Allow the solution to be in contact for at least 3 minutes, then dry.  
9. Repeat steps 1 to 5 with the sanitizing solution of step 6 replacing the Nickel Safe  
ice maker cleaner solution and filling the water trough to its maximum level  
10. Repeat step 5 to rinse the ice making system one more time.  
11. Press the ON/OFF button again. The machine will return to the regular ice making  
mode. Discard the first batch of ice.  
Major Functions  
1. Completely automatic operation  
2. When the ice storage bin is full of ice, the machine stops making ice and pro-  
ceeds to the cold preservation stage automatically. It starts making ice again once  
the cubes are removed.  
3. The fan motor responds to the ambient temperature. If it is cold, the motor will  
stop working to keep the cooling system in good working condition.  
4. A sensitive probe and accurate timer enhance the performance of the ice  
maker.  
5. Built-in compressor protection system  
17  
TROUBLESHOOTING  
Before Calling for Service  
If the unit appears to be malfunctioning, read through the OPERATION section of this  
manual first. If the problem persists, check the Troubleshooting Guide below and on  
the following page. The problem could be something very simple that can be solved  
without a service call.  
Problem  
Possible Cause  
Probable Correction  
Plug the ice maker in.  
Replace fuse โ€“ if this hap-  
pens, call for service to  
check for a short circuit in the  
ice maker.  
Turn the Power switch to ON.  
Remove some ice, making  
sure the ice-full probe is free  
of ice.  
The icemaker is unplugged.  
The fuse is blown.  
The Power switch is set at  
OFF.  
The ice storage bin is full of  
ice.  
The machine  
does not operate.  
The water supply tap is turned  
off.  
The water supply line is not  
properly connected.  
Turn on the water supply tap.  
Reconnect the water supply  
line.  
The water doesn't feed in  
after the machine starts.  
Condenser may be dirty.  
The air flow to the ice maker  
may be obstructed.  
The ambient temperature  
and water temperature are  
high, or machine is near  
some heat source.  
Clean the condenser.  
Check the installation.  
Machine makes ice, but ice  
storage bin does not fill up  
with ice.  
Check the installation.  
A few water drops fall to the  
Normal condensation on the  
floor when you open the door door or some water together  
to take out ice from storage  
Water is leaking from the unit. bin.  
Water supply connection  
leaking.  
with ice. Take care when you  
take out ice.  
Tighten fitting. See โ€œConnect-  
ing the Water Lineโ€.  
18  
TROUBLESHOOTING  
Problem  
Possible Cause  
Probable Correction  
Check if the water supply  
pressure is below 15 psig.  
Cubes are partially formed or Not enough water in the water Check water supply; filter  
are white at the bottom.  
trough..  
may be restricted.  
Check for a water leak at the  
water trough..  
The legs are not leveled and  
locked.  
Certain sounds are normal.  
Level and lock the feet. See  
โ€œLeveling the Ice Makerโ€.  
See โ€œNormal Soundsโ€.  
Noise during  
operation  
Reconnect the power supply  
line.  
The electricity is off.  
The room temperature is out  
The ice maker stops suddenly of the stated range.  
Cut off the electricity; let the  
ice maker stop working until  
the temperature returns to  
within the stated range.  
Remove some ice; be sure  
ice-full probe is free of ice.  
while making ice.  
The ice storage bin is full of  
ice.  
The body of the ice maker is  
electrified.  
The ground line isn't in the  
socket.  
Use a socket meeting the re-  
quired electrical standard.  
Scaling occurs  
frequently inside  
the machine.  
Using a water-softening de-  
vice installed in front of the  
water inlet.  
The water is too hard.  
The drain hole below the ice  
storage bin is blocked.  
Water leaks from the ice stor- The drain hose is kinked or  
Pull out the ice storage bin  
and clean the drain hole.  
Check the drain hose to  
make sure the water can  
drain out unhindered.  
age bin.  
improperly placed higher  
than the floor of the ice stor-  
age bin.  
19  
NOTES:  
20  
NOTES:  
21  
NOTES:  
22  
3355 Enterprise Ave, Suite #160,  
Fort Lauderdale, FL 33331  
Phone:(954) 202-7419 ยท Fax:(954) 202-7337  

Toshiba Air Conditioner Rav Sm804bt E User Manual
Sanyo Eco G Sgp Ew190m2g2w User Manual
Samsung Avmhh105ca0 User Manual
Pontiac Automobile Parts User Manual
Philips Sc468 User Manual
LG LHS 55SBC User Manual
LG DLGX2551 User Manual
KENWOOD KS 1300HT User Manual
Cuddelink User Manual
CRAFTSMAN 917.378950 User Manual