OWNER's INSTRUCTIONS MANUAL
Gas Fire Table
User's Guide and Instruction Manual
HF24501BB
FOR OUTDOOR USE ONLY !
If you smell gas and/or hear a gas hissing sound:
1. Immediately, SHUT OFF gas to the appliance.
2. Extinguish ALL open flames.
3. If odor continues, keep away from the appliance and immediately call your Gas
Supplier or Fire Department.
DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity
of this unit and or any other appliance.
An LP Gas tank not connected for use shall not be stored in the vicinity of this or
any other appliance.
Improper installation, adjustment, alteration, service or maintenance can cause
injury or damage to property.
Read and understand the Owner’s Manual thoroughly before installing or
servicing this Fire Table / Column.
If the information in this Owner's Manual is NOT followed exactly, a fire or
explosion may result and cause property damage, personal injury or loss of life.
CARBON MONOXIDE HAZARD.
This appliance can produce carbon monxide which is odorless.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as inside a camper, tent, car
or home.
Save this Owner's Manual and these instructions for future use.
If you are assembling this unit for someone else, give this Owner's Manual to them to read.
SAFETY INFORMATION
Part A.
Before you assemble or operate this unit, please read carefully this entire Owner's Manual.
Failure to do so may result in a fire, explosion, injury or death.
The installation of this unit must adhere to local codes or either the National Fuel
Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane
Installation Code.
• THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY!
This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
• This unit is to be used with LP Gas / Propane Gas only !
(Propane Gas tank is not attached and not delivered with this unit.
Propane and Gas Tank is sold separately).
• Do not attach a remote gas supply to this unit.
• This unit is NOT intended for Natural Gas.
• Converting this unit to Natural Gas is dangerous and not recommended.
The conversion of this unit shall void the manufacturer warranty.
• Do not use any solid fuel or charcoal for this unit.
• When igniting this unit, exercise caution as some gas pooling from the Burner may cause the flame to
flare that could cause injury.
• LP GAS WARNING : Do not use more than 1/4 inch depth of lava rocks / pumice stones above the burner
holes.
Excessive use of lava rocks / pumice stones, will suffocate the flame.
• If the Propane Gas Tank is leaking gas, you can smell, hear a hiss, or sense a leak at the source.
Do the following:
1. Disconnect the Propane Gas tank.
2. DO NOT attempt to fix the problem yourself.
3. Move yourself and all persons away from the immediate area.
4. Only when everyone is at a safe distance away from the Fire Table / Column, contact your Gas
Supplier or Fire Department for help.
• Applying too much Propane Gas may result in gas pooling and will NOT burn.
Allow fresh air into the unit so that the remaining gas may escape.
• DO NOT use a flame to check for gas leaks.
• The maximum inlet supply pressure: maximum Gas supply 11 inch w.c. (2.74kPa)
• Use LP propane tanks with the following dimensions: diameter 12 in, height 18 in - capacity 20lbs.
• You must use a Propane Gas Tank that has a collar to protect the Gas Valve.
• DO NOT fill tank over 80% full.
• The tank system must be set up for vapor withdrawal.
• STOP using if any part of the Propane Gas Tank is damaged.
Rust and dents in tank may be hazardous and should be inspected by a Gas Supplier.
• DO NOT burn anything other than the provided materials for this Fire Table.
• Keep away from the unit for the first 20 minutes after igniting your unit for the first time, as lava rocks /
pumice stones could pop out and cause injury.
Should any rocks pop out, discard them.
• Always ensure that lava rocks / pumice stones are completely dry before use.
Failure to do so will cause them to crack or pop.
• DO NOT operate unit until all parts are fully assembled.
• DO NOT paint or color any part of this Fire Table / Column.
• Unit may be hot while in use, DO NOT attempt to move it while in use.
• Never leave this Fire Table / Column unattended while in use.
• This unit is NOT intended for cooking.
• Keep all flammable items away and DO NOT use any other fireplace cover for this unit.
• Keep a safe distance to avoid burning skin or clothing.
• DO NOT sit or rest hands or feet on this Fire Table / Column.
• Never place hands or fingers onto upper portion of this unit while in use.
• Keep all electrical cords and fuel supply hose away from heated surfaces.
• Combustible material should NOT be within 72 inches of the top of the unit, and within 48 inches around
the entire unit.
• Keep the appliance area clear and free from combustible material, gasoline and other flammable vapors
and liquids.
• If the flame goes out while burning, turn the gas valve off.
Wait 5 minutes before repeating the initial lighting procedure.
Once you have a flame started, hold down the control knob for 1 minute.
• DO NOT add water into the unit.
• DO NOT operate unit if any part has been under water.
Immediately call for a Qualified Service Technician to inspect the appliance.
Where necessary, secure Qualified Service Technician to replace part(s) of the Control System and any
gas control parts that has been under water.
• DO NOT disconnect any part while the unit is in use.
• DO NOT store a spare Propane Gas Tank on or near this unit.
• If the Fire Table / Column is placed indoors for storage, detach the Propane GasTank and leave the tank
outdoors.
This unit is for outdoors use ONLY.
• DO NOT operate on a boat or vehicle.
This unit can only be used on any stationary outdoor flat surface ONLY
• Always remove protective cover before operating (where applicable) and / or use of your Fire Table /
Column.
• DO NOT set the Protective Cover (E) over the unit until the Fire Table / Column is turned off and
completely cooled down (where applicable).
• Check for leaks after not using the unit for long periods of time.
• Children must never operate this Fire Table / Column.
Children must be supervised AT ALL TIMES while near this Fire Table / Column.
• The maximum gas supply pressure is 250psi.
• All installation and repair should be done by a Qualified Service Technician.
This unit should be inspected annually and cleaned regularly.
• Inspect all elements of this Fire Table / Column before each use.
If there is damage, the Burner must be replaced.
• Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or injury.
• The gas supply tank should be constructed and marked with the specifications for the LP Gas tanks of
the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP Gas tanks,
spheres and tubes for Transportation of Dangerous Goods and Commission.
• The LP Gas tank must have a listed overfilling prevention device and a QCCI or Type I, LP Gas tank
connection.
• This heating appliance should NOT be used on plastic, artificial wood desks or any desk.
• Children and adults should be alerted to the hazards of high surface temperatures and should stay away
to avoid burns or clothing ignition.
• Young children MUST BE carefully supervised at all times when they are in the area of this appliance.
• Clothing or other flammable materials shall NOT be hung from the appliance or placed on or near the
appliance.
• Any guard or other protective device removed for servicing the appliance shall be replaced prior to
operating and use of this appliance.
• Installation and repair(s) should be done by a Qualified Service Technician.
The appliance should be inspected before use. If you suspect there are issues, contact a Qualified
Service person.
More frequent cleaning may be required as necessary.
It is imperative that the control compartment, burners and circulating airways of the appliance are kept
clean.
When APPLICABLE:
• Keep gas tank at least 5 feet away from unit when lit (if external tank).
• Allow Fire Burner / Column to cool down completely before placing on lid.
• Keep the hose away from any pathways to eliminate any accidental damage (if external tank).
• DO NOT use Fire Table / Column while lid is installed.
Always remove the lid while Fire Table / Column is in use.
Use only the Regulator (12/19) and Hose( 12) assembly provided with this unit.
Replacement parts must be supplied directly by manufacturer.
Inspect the Burner (08 ) before use of this unit.
If the Burner (08) shows any kind of damage, DO NOT operate the appliance.
For assistance with repair or replacement of the Burner (08) or any other parts,
call : 1- 818-435-3985.
NOTE: You must follow all steps to properly assemble this Fire Table / Column.
Make sure the Gas Valve is turned “OFF” before assembling.
DO NOT attempt to assemble without proper tools.
IGNITOR CONTROL BOARD
Part B
Herebelow is an exact visual display of the Operation Tablet as found on your Fire Table / Fire Column.
Read carefully before using.
User's Guide to Parts and Accessories of The Regulator,
Charge Valve of the Cylinder and Stelps to Connecting the
Gas Tank to the Fire Table /Column.
Part C
This Safety Information passage holds information that :
1 ) shows you the Regulator ( pre-connected to the Fire Table / Column )
2 ) the Charge Valve of the Gas Tank and its relevant Valves.
There are Fire Table / Column that holds the Gas Tank INTERNALLY and EXTERNALLY.
The Owner / User must know all the different parts : Charge Valves and Regulator.
This picture shows different parts of the Charge Valve of the Gas Tank and the Regulator (12/19 ) is pre-
connected to the Fire Table / Column. the different components and parts of the Gas Tank and the Fire
Table / Column Regulator, as show on the picture to the left here.
Pic. A : Shows the Charge Valve of the Cylinder with
the different Valves and Coupling Nut, these forms
the top of the Gas Cylinder.
Pic. B : Shows the Regular pre-connected to a hose.
This Regulator is pre-connected to the Fire Table /
Column.
There are 2 kinds of Fire Table / Column.
Type 1 : Fire Table / Column that has an internal housing for Gas Tank Cylinders, where the Gas Tank is
held inside the Table / Column. The Gas Tank is held and bound in place inside the FIre Table / Column
with the Metal Ring and locked down with a Wing Screw / Nut.
Type 2 : Fire Table / Column that has the Gas Tank externally visible, whereby the hose shall be NO
SHORTER than 5 feet.
In some cases, some Customers purchases separate Gas Tank Holder to hold the Gas Tank. In this case,
the 5 feet distance between the Fire Table / Column to the Gas Tank applies too.
User's Guide : Loading of Gas Tank into the Fire Table /
Column.
Part D
The Fire Table / Column has a Door. Open the Door .
Inside, you will see a Metal Stand with pre-attached
Wing Screw / Nut.
Proceed to Unscrew the Wing Screw / Nut
Load the Gas Tank / Gas Cylinder as indicated by
the bold black arrow.
Place the Tank / Cylinder gently and snugly into the
Metal Stand.
Position the Wing Screw / Nut in place.
Turn the Wing Screw until fully tightens into the Nut.
The Gas Tank / Gas Cylinder is now secured in
place.
User's Guide : Connecting the Fire Table / Column to the Gas
Cylinder.
Part E.
This next step guides you to connect the Fire Table / Column Regulator to the Gas Cylinder.
Step 1 : Plug the Black Coupling Nut on the
Regulator to the Cylinder Valve.
Step 2 : Turn the Black Coupling Nut, fully
CLOCKWISE until fully locked into the position.
Step 3 : Check for Leaks by : Brush some soap and
water mixture on all connections.
Turn the gas supply on;if extra large bubbles form
on any connection there may be a leak. If you smell
gas or a leak is discovered, IMMEDIATELY turn the
gas valve off, disconnect Propane Gas tank.
Do not use the appliance until the leak is repaired
FIRE TABLE / COLUMN PARTS INTRODUCTION
Part F.
Your Fire Table / Column is delivered pre-assembled whereby there is no assembly actions needed.
Herebelow is an introduction to all the parts that forms your Fire Table / Column.
Each part is different and holds its own function.
DO NOT attempt to change and or remove any part(s) thereof.
In the event of servicing and or operational issues, contact Qualified Services Technical Support and or
seek Qualified Service Technician.
This line art below demonstrates the internal components of the Burner.
For your conveneince all of the above components are individually desribed herebelow.
Tabulated here below are the description to all parts as shown in above Picture .
Item
01
Picture
Description
Qty
1
Guard
02
Thermocouple
1
03
04
Ground Wire
Ignition Pin
1
1
05
06
07
Burner Plate
1
1
1
Main Frame of Fire Table
Door
08
09
10
Burner Ring
Nozzle
1
1
1
Corrugated Pipe
11
12
13
Switching Valve
1
1
1
Regulator Valve with Gas
Hose
Control Knob
Ignitor
14
15
1
4
Foot
ETL Warning Label
Wing Screw with Nut
16
17
1
1
18
Metal Stand
1
User's Guide Parts and Accessories of Fire Table / Column.
Part G.
Tabulated herebelow is the User's Guide to various Parts and Accessories to form your complete Fire
Table /Column.
Before you start to assemble this product, make sure all parts are present.
Compare parts with package contents list.
If any parts are missing or damaged, DO NOT attempt to assemble the product.
CONTENTS
Before Beginning Assembly:
Item
A
Picture
Description
Qty
1 box
1
Lava Rocks
AAA Battery
B
C
Panel with door
1
D
E
Panel D
1
1
Protective Cover
F
G
H
Panel F
Panel G
1
1
1
Table Top
I
Metal Stand
1
Hardware
Item
Picture
Description
Qty
Bolt (M6*10MM)
12
①
②
Screwdriver
1
ASSEMBLY INSTRUCTIONS
1. Check that the Control Knob (13) for the gas supply system is turned to the “OFF” position before
starting any assembly.
D
C
2. Attach panel with door (C) and panel with (D) together using 2pcs of Bolts(01) with Screwdriver(02).
Pls do not fully tighten.
G
D
c
c
3. Attach panel (G ) to the panel (C) together using 2pcs of Bolts(01) with Screwdriver(02).
Pls do not fully tighten.
C
D
4. Attach panel (F) with Panel (G) and Panel (D) together using 4pcs Bolts(01) with Screwdriver(02).
Pls do not fully tighten.
5.Put Thank holder insert into the bottom holes . Tighten all Bolts
6.Put the metal base on the bottom of top, make sure the metal box contact with the window of the panel.
And tighten the Bolts
7.Fixed the metal base with top using 4pcs of Bolts(01) with Screwdriver(02). And tighten the Bolts
8.Turn over the Gas Fire Pit
USER'S INSTRUCTIONS
Part I.
Tabulated herebelow are the basic steps to help you light and use your Fire Table / Column.
STEP1
1. Check that the Control Knob (13) for the gas supply system is turned to the “OFF” position before
starting any assembly.
STEP 2
2. Open the Door (C) from the Fire Table / Column (C).
STEP 3
3. Place 20 lb. Propane Gas Tank (not included) into the Metal Stand (18).
Make sure the Propane Gas Tank is placed completely into the Metal Stand (18 ).
Turn the preassembled Wing Screw (17) in a clockwise direction in to the Nut (17) to secure the Propane
Gas Tank tightly.
STEP 4
4. Turn the Cylinder Valve (21 ) on the tank in a clockwise direction to TURN OFF SUPPLY of the LP Gas
supply .
Attach the preassembled Regulator (12/19) from the Fire Table / Column to the Cylinder Valve (21) by
turning the Black Regulator Coupling Nut (20 ) clockwise.
Make sure it is fastened securely and tighten connections - by HAND only.
STEP 5
5. Close the Door (C) back to the Mainframe of the Fire Table / Column (C ).
STEP 6
6. Remove the Electronic Ignitor Cap (14) on the electronic Ignitor (14) by unscrewing and slide the Battery
(B) into the battery slot (14).
Make sure the positive side of the Battery( B ) faces outwards.
Screw the Electronic Ignitor Cap (14) over the battery, tightly.
STEP 7
Subject to your preference, you may pour Lava Rocks / Pumice stones over the Burer Ring. The Guard
MUST NOT BE BLOCKED. Refer to guidance below :
Note : Do not place more than 1/4 inch depth of lava rocks above the burner holes. Doing so will
suffocate the flame.
Note : Do not place more than 3KG of lava rocks above the burner holes. Doing so will suffocate the
flame.
To ensure proper function, the Guard (01) on the Burner (08) should never have lava rocks (A) covered
over it.
SAFETY INFORMATION - OPERATIONS
Part J.
Before performing a leak test, be sure:
1. ) DO NOT press the Ignitor .
2. ) You are in a spacious outdoor area.
Connect the Propane Gas tank to the Regulator (12 /19) and turn the Valve (22) on the unit to the “OFF”
position.
Brush soap and water mixture onto all connections.
Turn the gas supply on;if extra large bubbles form on any connection there may be a leak. If you smell
gas or a leak is discovered, IMMEDIATELY turn the gas valve off, disconnect Propane Gas tank.
Do not use the appliance until the leak is repaired
The Fire Table / Column has a Door. Open the door. Inspect the Gas Hose (12) before use the Fire Table /
Column.
If there are signs of wear or abrasion on the hose, you must replace the Gas Hose (12).And the Gas Hose
must be supplied directly by manufacturer.
Lava rocks / pumice stones could pop up and strike somebody’s face during the process of lighting this
unit.
Stand away from the Fire Table / Column for the initial 20 minutes after igniting.
Observe flame colour and flame height when the
Fire Table/Column after being lit :
2 inches to 10 inches.
1. ) Flame color should be yellow / blue.
2. ) Flame height burns at 2 - 10 inches high.
Wait 10 minutes after extinguishing flame prior to replacing a lid (if applicable) or protective cover onto
the Fire Table / Column.
SAFETY INFORMATION
USING YOUR FIRE TABLE / COLUMN
Part K.
Before each use, inspect the Gas Hose (12). Replace Gas Hose(12) if there are any signs of cutting, wear
or abrasion.
Before you light your Fire Table / Column, please proceed / adopt the following steps :
1. Make sure the Control Knob (13) is in the “OFF” position.
2. Open the Door (07) and slowly open the Valve ( 22) on the Propane Gas Tank by turning the Contol
Knob (13) counterclockwise.
3. Close the Door (07) on the Main Frame (06) of the Fire Table / Column.
4. Push and hold in the Electronic Ignitor (14 ) to create sparks within the electrode continue to hold.
5. Push in the Control Knob (13) and turn to the “LOW” position.
Keep holding down the Control Knob (13) to allow gas to flow for 15 seconds.
6. If ignition doesn’t occur within a few seconds release the Control Knob (13) and rotate to the “OFF”
position.
Wait for 5 minutes for gas to clear and then repeat the above lighting instructions.
7. Once the Fire Table / Column is lit, the flame intensity may be controlled by turning the Control Knob
(13) between the “LOW” and “HIGH” positions.
8. Observe flame height when lit:
8.1. ) Flame color should be yellow / blue.
8.2. ) Flame height burns at 2 - 10 inches high.
SAFETY INFORMATION : TO SHUT DOWN YOUR FIRE TABLE
/ COLUMN
Part L.
To Shut Down your Fire Table / Column, please proceed / adopt the following steps :
1. Turn Control Knob (13) clockwise to the “OFF” position.
2. Close the Cylinder Valve ( 21) on the Propane Gas tank if you DO NOT intend to use it for a long time.
MAINTENANCE - FIRE TABLE / COLUMN
Part M.
• Before performing any maintenance work, ensure the Control Knob (13) is in the "OFF" position and
always disconnect Propane Gas tank.
• Keep the Fire Table / Column free and clear from all combustible materials.
• Visually inspect Burner (08) for obstructions and keep tank enclosure free and clear from debris.
• Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones /
lava rocks are completely cooled down. Wipe down with a soft cloth.
• Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
• Permanent damage may occur if powder or solvent comes in contact with painted or plastic
components on this Fire Table / Column.
• Keep the Fire Table / Column stored away from direct sunlight.
• If storing this unit inside, disconnect the Propane Gas tank from the Gas Valve (22) .
Leave the gas tank outside of your premises.
• Not using manufacturer approved or supplied parts/accessories may result in a defective condition and
shall void the warranty of this Fire Table / Column.
• Before performing any maintenance work, always:
1 ) ensure Control Knob (13) is in 'OFF' position
2 ) disconnect Propane Gas tank
• Keep the Fire Table / Column free and clear from all combustible materials.
• Visually inspect Burner (08) for obstructions and keep tank enclosure free and clear from debris.
• Place Lid (if applicable) and Protective Cover (E) on the Fire Table / Column when not in use.
MAINTENANCE : FIRE TABLE / COLUMN SURFACE CARE
Part N.
• Our Table / Column Fire Table material has been sealed with a treatment that prevents staining and
moisture absorption, and for product longevity this Fire Table / Column would still require proper care
and maintenance to ensure the integrity of the surface.
• Please see below for recommendations on maintaining your Fire Table / Column surface for years of
extended use:
• Clean any spills immediately to prevent permanent surface(s) staining or damage to your Fire Table /
Column.
Blot any liquid spills with a clean, dry cloth to avoid spreading of the spill to the rest of the table.
Immediate cleaning of stains / blotting of spills also prevents absorption of such stains / spills into the
surfaces, compared to if such stains / spills are left for exended periods on these surfaces.
• How to Clean your Fire Table / Column surface(s) :
Mix a mild dish soap into warm clean water, use a soft, clean cloth or sponge..
Then proceed to remove surface dirt, stains or mild spills.
Rinse all soap solution off from the surfaces with a damp cloth.
Dry off completely with a dry cloth to avoid water spots / water marks.
Regularly cleaning the Fire Table / Column surface will aid in a longer lasting product.
• DO NOT use petroleum-based or abrasive cleaning products.
DO NOT use any harsh brushes / rough sponges when cleaning the Fire Table / Column surface(s).
• DO NOT slide products across the Fire Table / Column surface(s) to avoid permanent scratching and or
damage(s).
• DO NOT place any food on the surface(s) of the Fire Table / Collumn.
DO NOT eat from the surface(s) of the Fire Table / Column surface.
• Fire Table / Column surface must be covered at all times when not in use.
Cover your product with an outdoor Protective Cover(E) when not in use to protect it from the elements.
Store your product indoors during winter months, leave the gas tank outside.
Avoiding extreme cold temperatures, as extreme cold temperatures may cause cracking of the tabletop.
TROUBLE SHOOTING
Part O.
Herebelow is a simple guide on frequently asked questions / frequently occurring issues.
Read through carefully and execute accordinlgy and adequately.
Whenever you are uncertain, please contact Qualified Technician Services and/or Fire Department.
Solution
Dry off with a soft cloth
Problem
Cause
Ignitor pin (04) and Burner
(08) are wet
Check which direction the battery is inserted OR
battery needs to be replaced
Ignitor Battery (B) is
incorrectly inserted
Contact Manufacturer for a replacement part
Ignitor Pin (04) is broken
Fire Pit / Fire Table /
Column DOES NOT
light up.
Reconnect wire to the ignitor box located inside the
table behind the ignitor box
Ground Wire (03) is loose or
disconnected
Ground Wire (03) is shorting
between Valve and Ignitor
Pin(04)
Contact Manufacturer for a replacement part
Check that the Gas tank isn’t empty
No Gas flow
Regulator(12/19) isn’t
connected securely to the
tank
Tighten Regulator connection to the Gas tank
Burner DOES NOT
light
while using a match
Check all hoses (12) for kinks and bends.
Gas flow is obstructed
Turn all gas flow connections OFF.
Insert an opened paperclip (or similar item) into each
of the burner ports to clear them out.
Burner holes are clogged
Check that all Burner holes are free of any small lava
rocks/ pumice stones pieces.
Flame is obstructed at
burner holes
Heater unit emits a lot
of black smoke
Straighten Hose (12) of all bends or kinks.
Check that the Gas tank isn’t empty.
Regulator(12) hose is kinked
No Gas flow
Turn the Control Knob(13) to the ‘OFF’ position.
Close the Tank Valve and disconnect Propane gas
tank.
Turn the Control Knob(13) to ‘HIGH’; wait 1 minute.
Turn the Control Knob (13) back to the 'OFF’
position.
Sudden drop in gas
flow
Excess flow Safety Valve(11)
has been activated
Reconnect Propane gas tank.
Light the fire unit as indicated in the ‘To Light’
section of this manual.
Increase flame to ‘HIGH’
High or gusting winds
No gas flow
Flame blows out
easily
Check that the gas tank isn’t empty
See ‘Sudden drop in gas flow’ above
Excess flow safety valve has
been activated
WARRANTY
Part P.
The manufacturer warranty shall be voided, and manufacturer disclaims any responsibility for the
following actions whereby the Customer / Consumer / Owner has :
• Made modification(s) to the unit and / or components including the Gas Valve assembly. The Owner
shall contact the Local Supplier and Quaified Service Person to repair these parts.
• Use any component part / change to parts that are NOT manufactured or approved by manufacturer
• Use and installation other than what is listed in this Owner's Manual.
Please contact the manufacturer for replacement parts.
CONTACT
Part Q.
If you have any questions or concerns, our Trained Staff are ready to assist you.
Contact: 1-818-435-3985
Monday-Friday 8 a.m. to 5 p.m. PST
|